Epson Stylus C84WN User guide

Epson Stylus C84WN User guide
Start Here
®
EPSON Stylus C84WN
Follow these instructions if you’re an advanced user and your network has a
wireless access point or AirPort® Base Station. This includes wired networks
that have wireless access points. For more detailed instructions, see your
Setup and Installation book.
1 Unpack and
Open the cartridge cover.
9
Insert each cartridge into its holder
and push it down until it clicks into
place.
10
Set Up the Printer
1
8
11
Take everything out of the box.
10
Setup and
Installation
Print server base
Printer Basics
Print server
Printer software
CD-ROM
Paper support
Print server
power supply
13
Read the license agreement. Click Next to accept the agreement
and continue.
Note: You must install the Java Runtime
Environment if it’s not already installed on
your computer.
14
Follow the instructions on the
screen to install the wireless
utilities. At the last screen,
click Done. You see the Wireless
Server Search window.
Note: Don’t remove the cartridge
labels, or ink may leak.
11
When you see the license agreement, read it and
click Yes to continue. Follow the instructions on the screen.
Close the cartridge cover.
12
When you see this window,
make sure Program Files
and WP-Admin are selected,
then click Next.
Press the ink button and close the printer cover. Wait while the
ink charges.
Continue with the instructions in section 3, “Connect the Print Server.”
3 Connect the Print Server
Place paper against the
right edge of the sheet
feeder, then slide the
edge guide against
the paper.
You see the Wireless Server
Search Window.
To check the printer, first turn
it off. Then hold down the
paper button as you press and
release the
power button
to turn it back on. The test
page prints.
2
Turn off the printer. Then connect the parallel cable to the printer
and print server.
3
Connect the power supply to the print server and plug in the AC
adapter. Both the green and yellow lights come on and then go out.
4
Turn on the printer.
5
To test the connection, press the test button for one second
and release it. The status page prints.
Macintosh
®
Before you begin, do the following:
•
Make sure that AirPort is on and that both AppleTalk® and
TCP/ IP are enabled.
•
Select a working connection to an AirPort Base Station or to an
access point.
•
Make sure that WEP encryption is disabled on your wireless network.
Printer
Remove all the tape and packing material inside and around the printer.
The tape may be in different places on your printer, so check carefully.
Slide the print server into the base and press firmly.
It should click into place.
Don’t load
paper above
this arrow
1
Power cord
1
Continue with the instructions in section 3,
“Connect the Print Server.”
If the test page doesn’t print, see the “Problem Solving” chapter
in Printer Basics.
Ink
cartridges
2
If you see this message, click Continue.
Caution: Don’t turn off the printer while the green light is flashing, unless
the printer hasn’t moved or made any noise for more than 5 minutes.
12
Parallel cable
Cartridge cover
2 Install the Software
For details, see your AirPort or Macintosh documentation.
Follow the appropriate instructions below to install the software if you
have a wireless access point or AirPort Base Station. If you don’t, see your
Setup and Installation book.
Don’t touch
this cable
Carefully remove
this piece
Windows
1
®
Slide the paper support into
the slot on the back
of the printer.
2
Insert your printer software CD-ROM.
3
Double-click Install EPSON
Stylus C84WN Printer Driver
and follow the instructions
on the screen.
4
4
5
Connect the printer’s power cord
to the printer, then plug it into a
standard electrical outlet.
Power button
7
3
Mac® OS X: Double-click the EPSON CD-ROM icon to open it,
then double-click the EPSON OS X Installer icon.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
4
Lower the output tray, pull out the
extension, and open the cover.
Shake the package of ink cartridges
4 or 5 times. Then remove the
cartridges from the package.
(Don’t shake them after
removing the packaging.)
continue
Double-click Install EPSON Stylus
C84WN Printer Driver.
5
If you’re running Mac OS X, enter your
administrator password, if necessary.
6
Follow the instructions on the screen
to install the driver and restart your
Macintosh.
7
Do one of the following:
Mac OS X: Double-click the EPSON CD-ROM icon to open it, then
double-click the EPSON OS X Installer icon.
When you see this window, click Stop
searching. Then follow the instructions
on the screen to finish installing and
register your printer.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
8
Note: The Stop searching button
may take a minute or two to appear.
Press the printer’s
power button
until the green power light comes on.
5
6
Insert your printer software CD-ROM.
Make sure the wireless mode for your computer is set to Infrastructure
and WEP encryption is disabled.
For instructions, see the documentation for your wireless adapter.
3
2
9
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
10
Double-click Register Your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
11
Double-click Install EpsonNet
Wireless Print Server Utilities.
You see the print server install
window.
12
Click Next.
Double-click Install EPSON Network Status Monitor.
Follow the on-screen instructions.
6
Double-click Install EPSON Printer Movies and User Guide (EPIC)
and follow the on-screen instructions.
7
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
8
Double-click Register your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
9
Double-click Install EpsonNet Wireless Print Server Utilities.
continue
Double-click Install Printer Movies and Guide (EPIC) and follow the
on-screen instructions.
Test button
If the status page doesn’t print, or it indicates that zero bytes were
transmitted or received, check the solutions under “Problems?”
on the back of this sheet.
continue
Turn over
Start Here
®
EPSON Stylus C84WN
Follow these instructions if you’re an advanced user and your network has a
wireless access point or AirPort® Base Station. This includes wired networks
that have wireless access points. For more detailed instructions, see your
Setup and Installation book.
1 Unpack and
Open the cartridge cover.
9
Insert each cartridge into its holder
and push it down until it clicks into
place.
10
Set Up the Printer
1
8
11
Take everything out of the box.
10
Setup and
Installation
Print server base
Printer Basics
Print server
Printer software
CD-ROM
Paper support
Print server
power supply
13
Read the license agreement. Click Next to accept the agreement
and continue.
Note: You must install the Java Runtime
Environment if it’s not already installed on
your computer.
14
Follow the instructions on the
screen to install the wireless
utilities. At the last screen,
click Done. You see the Wireless
Server Search window.
Note: Don’t remove the cartridge
labels, or ink may leak.
11
When you see the license agreement, read it and
click Yes to continue. Follow the instructions on the screen.
Close the cartridge cover.
12
When you see this window,
make sure Program Files
and WP-Admin are selected,
then click Next.
Press the ink button and close the printer cover. Wait while the
ink charges.
Continue with the instructions in section 3, “Connect the Print Server.”
3 Connect the Print Server
Place paper against the
right edge of the sheet
feeder, then slide the
edge guide against
the paper.
You see the Wireless Server
Search Window.
To check the printer, first turn
it off. Then hold down the
paper button as you press and
release the
power button
to turn it back on. The test
page prints.
2
Turn off the printer. Then connect the parallel cable to the printer
and print server.
3
Connect the power supply to the print server and plug in the AC
adapter. Both the green and yellow lights come on and then go out.
4
Turn on the printer.
5
To test the connection, press the test button for one second
and release it. The status page prints.
Macintosh
®
Before you begin, do the following:
•
Make sure that AirPort is on and that both AppleTalk® and
TCP/ IP are enabled.
•
Select a working connection to an AirPort Base Station or to an
access point.
•
Make sure that WEP encryption is disabled on your wireless network.
Printer
Remove all the tape and packing material inside and around the printer.
The tape may be in different places on your printer, so check carefully.
Slide the print server into the base and press firmly.
It should click into place.
Don’t load
paper above
this arrow
1
Power cord
1
Continue with the instructions in section 3,
“Connect the Print Server.”
If the test page doesn’t print, see the “Problem Solving” chapter
in Printer Basics.
Ink
cartridges
2
If you see this message, click Continue.
Caution: Don’t turn off the printer while the green light is flashing, unless
the printer hasn’t moved or made any noise for more than 5 minutes.
12
Parallel cable
Cartridge cover
2 Install the Software
For details, see your AirPort or Macintosh documentation.
Follow the appropriate instructions below to install the software if you
have a wireless access point or AirPort Base Station. If you don’t, see your
Setup and Installation book.
Don’t touch
this cable
Carefully remove
this piece
Windows
1
®
Slide the paper support into
the slot on the back
of the printer.
2
Insert your printer software CD-ROM.
3
Double-click Install EPSON
Stylus C84WN Printer Driver
and follow the instructions
on the screen.
4
4
5
Connect the printer’s power cord
to the printer, then plug it into a
standard electrical outlet.
Power button
7
3
Mac® OS X: Double-click the EPSON CD-ROM icon to open it,
then double-click the EPSON OS X Installer icon.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
4
Lower the output tray, pull out the
extension, and open the cover.
Shake the package of ink cartridges
4 or 5 times. Then remove the
cartridges from the package.
(Don’t shake them after
removing the packaging.)
continue
Double-click Install EPSON Stylus
C84WN Printer Driver.
5
If you’re running Mac OS X, enter your
administrator password, if necessary.
6
Follow the instructions on the screen
to install the driver and restart your
Macintosh.
7
Do one of the following:
Mac OS X: Double-click the EPSON CD-ROM icon to open it, then
double-click the EPSON OS X Installer icon.
When you see this window, click Stop
searching. Then follow the instructions
on the screen to finish installing and
register your printer.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
8
Note: The Stop searching button
may take a minute or two to appear.
Press the printer’s
power button
until the green power light comes on.
5
6
Insert your printer software CD-ROM.
Make sure the wireless mode for your computer is set to Infrastructure
and WEP encryption is disabled.
For instructions, see the documentation for your wireless adapter.
3
2
9
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
10
Double-click Register Your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
11
Double-click Install EpsonNet
Wireless Print Server Utilities.
You see the print server install
window.
12
Click Next.
Double-click Install EPSON Network Status Monitor.
Follow the on-screen instructions.
6
Double-click Install EPSON Printer Movies and User Guide (EPIC)
and follow the on-screen instructions.
7
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
8
Double-click Register your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
9
Double-click Install EpsonNet Wireless Print Server Utilities.
continue
Double-click Install Printer Movies and Guide (EPIC) and follow the
on-screen instructions.
Test button
If the status page doesn’t print, or it indicates that zero bytes were
transmitted or received, check the solutions under “Problems?”
on the back of this sheet.
continue
Turn over
Start Here
®
EPSON Stylus C84WN
Follow these instructions if you’re an advanced user and your network has a
wireless access point or AirPort® Base Station. This includes wired networks
that have wireless access points. For more detailed instructions, see your
Setup and Installation book.
1 Unpack and
Open the cartridge cover.
9
Insert each cartridge into its holder
and push it down until it clicks into
place.
10
Set Up the Printer
1
8
11
Take everything out of the box.
10
Setup and
Installation
Print server base
Printer Basics
Print server
Printer software
CD-ROM
Paper support
Print server
power supply
13
Read the license agreement. Click Next to accept the agreement
and continue.
Note: You must install the Java Runtime
Environment if it’s not already installed on
your computer.
14
Follow the instructions on the
screen to install the wireless
utilities. At the last screen,
click Done. You see the Wireless
Server Search window.
Note: Don’t remove the cartridge
labels, or ink may leak.
11
When you see the license agreement, read it and
click Yes to continue. Follow the instructions on the screen.
Close the cartridge cover.
12
When you see this window,
make sure Program Files
and WP-Admin are selected,
then click Next.
Press the ink button and close the printer cover. Wait while the
ink charges.
Continue with the instructions in section 3, “Connect the Print Server.”
3 Connect the Print Server
Place paper against the
right edge of the sheet
feeder, then slide the
edge guide against
the paper.
You see the Wireless Server
Search Window.
To check the printer, first turn
it off. Then hold down the
paper button as you press and
release the
power button
to turn it back on. The test
page prints.
2
Turn off the printer. Then connect the parallel cable to the printer
and print server.
3
Connect the power supply to the print server and plug in the AC
adapter. Both the green and yellow lights come on and then go out.
4
Turn on the printer.
5
To test the connection, press the test button for one second
and release it. The status page prints.
Macintosh
®
Before you begin, do the following:
•
Make sure that AirPort is on and that both AppleTalk® and
TCP/ IP are enabled.
•
Select a working connection to an AirPort Base Station or to an
access point.
•
Make sure that WEP encryption is disabled on your wireless network.
Printer
Remove all the tape and packing material inside and around the printer.
The tape may be in different places on your printer, so check carefully.
Slide the print server into the base and press firmly.
It should click into place.
Don’t load
paper above
this arrow
1
Power cord
1
Continue with the instructions in section 3,
“Connect the Print Server.”
If the test page doesn’t print, see the “Problem Solving” chapter
in Printer Basics.
Ink
cartridges
2
If you see this message, click Continue.
Caution: Don’t turn off the printer while the green light is flashing, unless
the printer hasn’t moved or made any noise for more than 5 minutes.
12
Parallel cable
Cartridge cover
2 Install the Software
For details, see your AirPort or Macintosh documentation.
Follow the appropriate instructions below to install the software if you
have a wireless access point or AirPort Base Station. If you don’t, see your
Setup and Installation book.
Don’t touch
this cable
Carefully remove
this piece
Windows
1
®
Slide the paper support into
the slot on the back
of the printer.
2
Insert your printer software CD-ROM.
3
Double-click Install EPSON
Stylus C84WN Printer Driver
and follow the instructions
on the screen.
4
4
5
Connect the printer’s power cord
to the printer, then plug it into a
standard electrical outlet.
Power button
7
3
Mac® OS X: Double-click the EPSON CD-ROM icon to open it,
then double-click the EPSON OS X Installer icon.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
4
Lower the output tray, pull out the
extension, and open the cover.
Shake the package of ink cartridges
4 or 5 times. Then remove the
cartridges from the package.
(Don’t shake them after
removing the packaging.)
continue
Double-click Install EPSON Stylus
C84WN Printer Driver.
5
If you’re running Mac OS X, enter your
administrator password, if necessary.
6
Follow the instructions on the screen
to install the driver and restart your
Macintosh.
7
Do one of the following:
Mac OS X: Double-click the EPSON CD-ROM icon to open it, then
double-click the EPSON OS X Installer icon.
When you see this window, click Stop
searching. Then follow the instructions
on the screen to finish installing and
register your printer.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
8
Note: The Stop searching button
may take a minute or two to appear.
Press the printer’s
power button
until the green power light comes on.
5
6
Insert your printer software CD-ROM.
Make sure the wireless mode for your computer is set to Infrastructure
and WEP encryption is disabled.
For instructions, see the documentation for your wireless adapter.
3
2
9
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
10
Double-click Register Your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
11
Double-click Install EpsonNet
Wireless Print Server Utilities.
You see the print server install
window.
12
Click Next.
Double-click Install EPSON Network Status Monitor.
Follow the on-screen instructions.
6
Double-click Install EPSON Printer Movies and User Guide (EPIC)
and follow the on-screen instructions.
7
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
8
Double-click Register your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
9
Double-click Install EpsonNet Wireless Print Server Utilities.
continue
Double-click Install Printer Movies and Guide (EPIC) and follow the
on-screen instructions.
Test button
If the status page doesn’t print, or it indicates that zero bytes were
transmitted or received, check the solutions under “Problems?”
on the back of this sheet.
continue
Turn over
Start Here
®
EPSON Stylus C84WN
Follow these instructions if you’re an advanced user and your network has a
wireless access point or AirPort® Base Station. This includes wired networks
that have wireless access points. For more detailed instructions, see your
Setup and Installation book.
1 Unpack and
Open the cartridge cover.
9
Insert each cartridge into its holder
and push it down until it clicks into
place.
10
Set Up the Printer
1
8
11
Take everything out of the box.
10
Setup and
Installation
Print server base
Printer Basics
Print server
Printer software
CD-ROM
Paper support
Print server
power supply
13
Read the license agreement. Click Next to accept the agreement
and continue.
Note: You must install the Java Runtime
Environment if it’s not already installed on
your computer.
14
Follow the instructions on the
screen to install the wireless
utilities. At the last screen,
click Done. You see the Wireless
Server Search window.
Note: Don’t remove the cartridge
labels, or ink may leak.
11
When you see the license agreement, read it and
click Yes to continue. Follow the instructions on the screen.
Close the cartridge cover.
12
When you see this window,
make sure Program Files
and WP-Admin are selected,
then click Next.
Press the ink button and close the printer cover. Wait while the
ink charges.
Continue with the instructions in section 3, “Connect the Print Server.”
3 Connect the Print Server
Place paper against the
right edge of the sheet
feeder, then slide the
edge guide against
the paper.
You see the Wireless Server
Search Window.
To check the printer, first turn
it off. Then hold down the
paper button as you press and
release the
power button
to turn it back on. The test
page prints.
2
Turn off the printer. Then connect the parallel cable to the printer
and print server.
3
Connect the power supply to the print server and plug in the AC
adapter. Both the green and yellow lights come on and then go out.
4
Turn on the printer.
5
To test the connection, press the test button for one second
and release it. The status page prints.
Macintosh
®
Before you begin, do the following:
•
Make sure that AirPort is on and that both AppleTalk® and
TCP/ IP are enabled.
•
Select a working connection to an AirPort Base Station or to an
access point.
•
Make sure that WEP encryption is disabled on your wireless network.
Printer
Remove all the tape and packing material inside and around the printer.
The tape may be in different places on your printer, so check carefully.
Slide the print server into the base and press firmly.
It should click into place.
Don’t load
paper above
this arrow
1
Power cord
1
Continue with the instructions in section 3,
“Connect the Print Server.”
If the test page doesn’t print, see the “Problem Solving” chapter
in Printer Basics.
Ink
cartridges
2
If you see this message, click Continue.
Caution: Don’t turn off the printer while the green light is flashing, unless
the printer hasn’t moved or made any noise for more than 5 minutes.
12
Parallel cable
Cartridge cover
2 Install the Software
For details, see your AirPort or Macintosh documentation.
Follow the appropriate instructions below to install the software if you
have a wireless access point or AirPort Base Station. If you don’t, see your
Setup and Installation book.
Don’t touch
this cable
Carefully remove
this piece
Windows
1
®
Slide the paper support into
the slot on the back
of the printer.
2
Insert your printer software CD-ROM.
3
Double-click Install EPSON
Stylus C84WN Printer Driver
and follow the instructions
on the screen.
4
4
5
Connect the printer’s power cord
to the printer, then plug it into a
standard electrical outlet.
Power button
7
3
Mac® OS X: Double-click the EPSON CD-ROM icon to open it,
then double-click the EPSON OS X Installer icon.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
4
Lower the output tray, pull out the
extension, and open the cover.
Shake the package of ink cartridges
4 or 5 times. Then remove the
cartridges from the package.
(Don’t shake them after
removing the packaging.)
continue
Double-click Install EPSON Stylus
C84WN Printer Driver.
5
If you’re running Mac OS X, enter your
administrator password, if necessary.
6
Follow the instructions on the screen
to install the driver and restart your
Macintosh.
7
Do one of the following:
Mac OS X: Double-click the EPSON CD-ROM icon to open it, then
double-click the EPSON OS X Installer icon.
When you see this window, click Stop
searching. Then follow the instructions
on the screen to finish installing and
register your printer.
Mac OS 8.6 to 9.x: Double-click the EPSON OS 8 & 9 Installer icon.
8
Note: The Stop searching button
may take a minute or two to appear.
Press the printer’s
power button
until the green power light comes on.
5
6
Insert your printer software CD-ROM.
Make sure the wireless mode for your computer is set to Infrastructure
and WEP encryption is disabled.
For instructions, see the documentation for your wireless adapter.
3
2
9
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
10
Double-click Register Your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
11
Double-click Install EpsonNet
Wireless Print Server Utilities.
You see the print server install
window.
12
Click Next.
Double-click Install EPSON Network Status Monitor.
Follow the on-screen instructions.
6
Double-click Install EPSON Printer Movies and User Guide (EPIC)
and follow the on-screen instructions.
7
Optionally, double-click Install EPSON Software Film Factory
and follow the instructions on the screen to install this photo
management program.
8
Double-click Register your EPSON Stylus C84WN and follow the
on-screen instructions to register your printer. Close your browser
when you’re done.
9
Double-click Install EpsonNet Wireless Print Server Utilities.
continue
Double-click Install Printer Movies and Guide (EPIC) and follow the
on-screen instructions.
Test button
If the status page doesn’t print, or it indicates that zero bytes were
transmitted or received, check the solutions under “Problems?”
on the back of this sheet.
continue
Turn over
4 Configure the Print Server
After the files are installed, you see the Wireless Server Search window:
5 Set Up a Network Port
5
You are getting a wireless
signal, but you are not
able to print.
Make sure Network is selected, then click Browse.
You need to add the printer’s network port to each Windows computer that
will access it. If necessary, print a status page and note the server name or
IP address of your print server before you begin. For instructions on setting
up a network port on Windows NT,® see the Setup and Installation book.
Check the Wireless Server Search window to
make sure your wireless link has adequate
strength—at least 50 percent. If the signal is
weak, try moving the print server, printer, and
access point or base station closer together.
Windows XP or 2000
1
1
Windows XP: Click Start > Control Panel > Printers and
Other Hardware > Printers and Faxes.
Click START. You see server information like this:
Appears
when the
server is
found
Signal strength
Do one of the following:
Windows 2000: Click Start > Settings > Printers.
Indicates
signal strength
It may take up to 2 minutes for the server information to appear.
2
Right-click your printer icon, then click Properties.
3
On the Ports tab, select your printer (if necessary), and click Add Port.
4
Select Standard TCP/IP Port and click New Port.
6
Check the printer’s lights to see if there is a
problem with the printer. See Printer Basics
for details.
If you don’t pick up a signal from the print server, move the print server
and access point closer to each other and to the computer. If that
doesn’t work, try the solutions under “Problems?.”
2
3
When you see server information on the screen, click STOP.
Then click CONFIGURE.
When you see a message asking for a password, click OK.
You see the Wireless Configuration screen:
5
When you see the Add Standard TCP/IP Printer Port Wizard, click Next.
6
Enter your print server name or IP address and click Next.
Make sure that your network port is set up
correctly (Windows), or that you’ve added
the printer to Print Center or Printer Setup
Utility (Mac OS X) or selected the printer
in the Chooser (Mac OS 8.6 to 9.x).
Click to expand the network path, then click the + next to
Epson_Ipr and select your printer.
7
Click OK, then click OK again. Click Apply on the Details tab.
8
To test the connection, click the General tab and click
Print Test Page.
You are unable to see the
printer in the Macintosh
Chooser or Print Center.
Make sure you are connected to the correct
AirPort network. See your AirPort
documentation for details.
You see a communication
error when you try to print.
You may see an error message if another
computer on your network is trying to print at
the same time. Wait until the first print job is
done. Your job will print when it reaches the
top of the print queue.
Paper jams frequently.
Try loading fewer sheets of paper.
If the test page prints, click Yes, then click OK to close the Properties
window.
If it doesn’t print, try the suggestions under “Problems?” below.
Congratulations! You’re ready for wireless printing. See Printer Basics
for more information.
When you load paper, don’t push it in.
Also, slide the left edge guide against the
paper, but not too tightly.
Use new, smooth, high-quality paper.
7
Follow the instructions on the screen to complete the wizard.
Note: For descriptions of all the settings on the Wireless
Configuration screen, see Appendix A in Setup and Installation.
8
Click Close to close the printer ports window, then click Apply
on the Properties window.
4
Enter a Server Name that is easy to remember.
9
To test the connection, select the General tab and click
Print Test Page.
5
Check that Boot Method is set to AUTO.
Click OK.
7
When you see the Wireless Server Search window again, click QUIT.
Congratulations! You’re ready for wireless printing. See Printer Basics for
more information.
1
On the EPSON® Installation Program screen, double-click Install
EpsonNet Direct Print Utility and follow the on-screen instructions
to install the utility and restart your computer.
Do one of the following:
Windows: Click Finish on the last screen. Then continue with
the instructions in the next section to set up a network port.
Mac OS X: Add the printer to Print Center or Printer Setup Utility.
(For details, see Setup and Installation.) Congratulations! You’re
ready for wireless printing. See Printer Basics for instructions.
For more problem solving tips on wireless printing, see Setup and Installation.
For printer problems, see Printer Basics.
Make sure the parallel cable is securely
connected to both the print server and your
computer.
Make sure the printer is on. Check the printer’s
lights to see if there is a problem. See Printer
Basics for details.
Unplug the AC adapter from the print server
and plug it in again. Then press the print
server’s test button for 10 seconds to reset
it to its factory defaults. If you still have
problems, contact EPSON.
If it doesn’t print, try the solutions under “Problems?” in the next
column.
Windows Me or 98
8
The print server’s status
page doesn’t print, or it
indicates that zero bytes
were transmitted
or received.
If the test page prints, click OK to close the Properties window.
Note: Always set the Boot Method to AUTO, unless you plan to
unplug the print server. See Setup and Installation for details.
6
Problems?
The Wireless Server
Search window fails to
pick up a signal from
the print server.
Test button
Make sure the print server, printer, and access
point are not near a cordless phone unit,
microwave oven, BluetoothTM device, or large
metal object. Try moving them to a new
location, or try moving them closer to
each other.
Press the print server’s test button for 10
seconds to reset it. On Macintosh, select your
wireless network again.
2
Click Start > Settings > Printers.
3
Right-click your printer icon, then click Properties. Click the Details tab.
4
Click Add Port.
Try restarting your computer.
On Macintosh, make sure that AirPort is
on, and that both AppleTalk and TCP/ IP
are enabled.
Mac OS 8.6 to 9.x: Select your C84 Series printer icon in the
Macintosh Chooser. Congratulations! You’re ready for wireless
printing. See Printer Basics for more information.
Confirm the connection between the computer
and your access point or base station. If you
have problems establishing a connection,
reset the access point or base station.
Where to Get Help
EPSON Printer Information Center
View Print Show animations that quickly tell you how to load special paper,
replace ink cartridges, and clean the print head. Also includes a User Guide
with additional printer information. To launch EPSON Printer Information
Center, double-click the EPIC or EPSON Printer Info Center icon on your
desktop.
Printer Basics
Includes instructions for printing, maintaining the printer, and solving
basic printer problems.
Setup and Installation
Provides greater detail about how to set up your printer for wireless network
printing. Includes system requirements, print server specifications, and
descriptions of settings on the Wireless Server Configuration screen.
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Here you can download drivers and other files, look at product documentation
and troubleshooting information, and receive technical advice through e-mail.
Automated Telephone Services
A variety of help services are available 24 hours a day, 7 days a week.
To use these services, you must have a touch tone telephone and call
(800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70445.
Use this code to quickly select the EPSON Stylus C84WN in SoundAdvice.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is
a trademark, and SoundAdvice is a service mark of Epson America, Inc.
continue
continue
General Notice: Other product names are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
© 2004 Epson America, Inc.
1/04 Printed in USA
CPD-17476
4 Configure the Print Server
After the files are installed, you see the Wireless Server Search window:
5 Set Up a Network Port
5
You are getting a wireless
signal, but you are not
able to print.
Make sure Network is selected, then click Browse.
You need to add the printer’s network port to each Windows computer that
will access it. If necessary, print a status page and note the server name or
IP address of your print server before you begin. For instructions on setting
up a network port on Windows NT,® see the Setup and Installation book.
Check the Wireless Server Search window to
make sure your wireless link has adequate
strength—at least 50 percent. If the signal is
weak, try moving the print server, printer, and
access point or base station closer together.
Windows XP or 2000
1
1
Windows XP: Click Start > Control Panel > Printers and
Other Hardware > Printers and Faxes.
Click START. You see server information like this:
Appears
when the
server is
found
Signal strength
Do one of the following:
Windows 2000: Click Start > Settings > Printers.
Indicates
signal strength
It may take up to 2 minutes for the server information to appear.
2
Right-click your printer icon, then click Properties.
3
On the Ports tab, select your printer (if necessary), and click Add Port.
4
Select Standard TCP/IP Port and click New Port.
6
Check the printer’s lights to see if there is a
problem with the printer. See Printer Basics
for details.
If you don’t pick up a signal from the print server, move the print server
and access point closer to each other and to the computer. If that
doesn’t work, try the solutions under “Problems?.”
2
3
When you see server information on the screen, click STOP.
Then click CONFIGURE.
When you see a message asking for a password, click OK.
You see the Wireless Configuration screen:
5
When you see the Add Standard TCP/IP Printer Port Wizard, click Next.
6
Enter your print server name or IP address and click Next.
Make sure that your network port is set up
correctly (Windows), or that you’ve added
the printer to Print Center or Printer Setup
Utility (Mac OS X) or selected the printer
in the Chooser (Mac OS 8.6 to 9.x).
Click to expand the network path, then click the + next to
Epson_Ipr and select your printer.
7
Click OK, then click OK again. Click Apply on the Details tab.
8
To test the connection, click the General tab and click
Print Test Page.
You are unable to see the
printer in the Macintosh
Chooser or Print Center.
Make sure you are connected to the correct
AirPort network. See your AirPort
documentation for details.
You see a communication
error when you try to print.
You may see an error message if another
computer on your network is trying to print at
the same time. Wait until the first print job is
done. Your job will print when it reaches the
top of the print queue.
Paper jams frequently.
Try loading fewer sheets of paper.
If the test page prints, click Yes, then click OK to close the Properties
window.
If it doesn’t print, try the suggestions under “Problems?” below.
Congratulations! You’re ready for wireless printing. See Printer Basics
for more information.
When you load paper, don’t push it in.
Also, slide the left edge guide against the
paper, but not too tightly.
Use new, smooth, high-quality paper.
7
Follow the instructions on the screen to complete the wizard.
Note: For descriptions of all the settings on the Wireless
Configuration screen, see Appendix A in Setup and Installation.
8
Click Close to close the printer ports window, then click Apply
on the Properties window.
4
Enter a Server Name that is easy to remember.
9
To test the connection, select the General tab and click
Print Test Page.
5
Check that Boot Method is set to AUTO.
Click OK.
7
When you see the Wireless Server Search window again, click QUIT.
Congratulations! You’re ready for wireless printing. See Printer Basics for
more information.
1
On the EPSON® Installation Program screen, double-click Install
EpsonNet Direct Print Utility and follow the on-screen instructions
to install the utility and restart your computer.
Do one of the following:
Windows: Click Finish on the last screen. Then continue with
the instructions in the next section to set up a network port.
Mac OS X: Add the printer to Print Center or Printer Setup Utility.
(For details, see Setup and Installation.) Congratulations! You’re
ready for wireless printing. See Printer Basics for instructions.
For more problem solving tips on wireless printing, see Setup and Installation.
For printer problems, see Printer Basics.
Make sure the parallel cable is securely
connected to both the print server and your
computer.
Make sure the printer is on. Check the printer’s
lights to see if there is a problem. See Printer
Basics for details.
Unplug the AC adapter from the print server
and plug it in again. Then press the print
server’s test button for 10 seconds to reset
it to its factory defaults. If you still have
problems, contact EPSON.
If it doesn’t print, try the solutions under “Problems?” in the next
column.
Windows Me or 98
8
The print server’s status
page doesn’t print, or it
indicates that zero bytes
were transmitted
or received.
If the test page prints, click OK to close the Properties window.
Note: Always set the Boot Method to AUTO, unless you plan to
unplug the print server. See Setup and Installation for details.
6
Problems?
The Wireless Server
Search window fails to
pick up a signal from
the print server.
Test button
Make sure the print server, printer, and access
point are not near a cordless phone unit,
microwave oven, BluetoothTM device, or large
metal object. Try moving them to a new
location, or try moving them closer to
each other.
Press the print server’s test button for 10
seconds to reset it. On Macintosh, select your
wireless network again.
2
Click Start > Settings > Printers.
3
Right-click your printer icon, then click Properties. Click the Details tab.
4
Click Add Port.
Try restarting your computer.
On Macintosh, make sure that AirPort is
on, and that both AppleTalk and TCP/ IP
are enabled.
Mac OS 8.6 to 9.x: Select your C84 Series printer icon in the
Macintosh Chooser. Congratulations! You’re ready for wireless
printing. See Printer Basics for more information.
Confirm the connection between the computer
and your access point or base station. If you
have problems establishing a connection,
reset the access point or base station.
Where to Get Help
EPSON Printer Information Center
View Print Show animations that quickly tell you how to load special paper,
replace ink cartridges, and clean the print head. Also includes a User Guide
with additional printer information. To launch EPSON Printer Information
Center, double-click the EPIC or EPSON Printer Info Center icon on your
desktop.
Printer Basics
Includes instructions for printing, maintaining the printer, and solving
basic printer problems.
Setup and Installation
Provides greater detail about how to set up your printer for wireless network
printing. Includes system requirements, print server specifications, and
descriptions of settings on the Wireless Server Configuration screen.
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Here you can download drivers and other files, look at product documentation
and troubleshooting information, and receive technical advice through e-mail.
Automated Telephone Services
A variety of help services are available 24 hours a day, 7 days a week.
To use these services, you must have a touch tone telephone and call
(800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70445.
Use this code to quickly select the EPSON Stylus C84WN in SoundAdvice.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is
a trademark, and SoundAdvice is a service mark of Epson America, Inc.
continue
continue
General Notice: Other product names are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
© 2004 Epson America, Inc.
1/04 Printed in USA
CPD-17476
4 Configure the Print Server
After the files are installed, you see the Wireless Server Search window:
5 Set Up a Network Port
5
You are getting a wireless
signal, but you are not
able to print.
Make sure Network is selected, then click Browse.
You need to add the printer’s network port to each Windows computer that
will access it. If necessary, print a status page and note the server name or
IP address of your print server before you begin. For instructions on setting
up a network port on Windows NT,® see the Setup and Installation book.
Check the Wireless Server Search window to
make sure your wireless link has adequate
strength—at least 50 percent. If the signal is
weak, try moving the print server, printer, and
access point or base station closer together.
Windows XP or 2000
1
1
Windows XP: Click Start > Control Panel > Printers and
Other Hardware > Printers and Faxes.
Click START. You see server information like this:
Appears
when the
server is
found
Signal strength
Do one of the following:
Windows 2000: Click Start > Settings > Printers.
Indicates
signal strength
It may take up to 2 minutes for the server information to appear.
2
Right-click your printer icon, then click Properties.
3
On the Ports tab, select your printer (if necessary), and click Add Port.
4
Select Standard TCP/IP Port and click New Port.
6
Check the printer’s lights to see if there is a
problem with the printer. See Printer Basics
for details.
If you don’t pick up a signal from the print server, move the print server
and access point closer to each other and to the computer. If that
doesn’t work, try the solutions under “Problems?.”
2
3
When you see server information on the screen, click STOP.
Then click CONFIGURE.
When you see a message asking for a password, click OK.
You see the Wireless Configuration screen:
5
When you see the Add Standard TCP/IP Printer Port Wizard, click Next.
6
Enter your print server name or IP address and click Next.
Make sure that your network port is set up
correctly (Windows), or that you’ve added
the printer to Print Center or Printer Setup
Utility (Mac OS X) or selected the printer
in the Chooser (Mac OS 8.6 to 9.x).
Click to expand the network path, then click the + next to
Epson_Ipr and select your printer.
7
Click OK, then click OK again. Click Apply on the Details tab.
8
To test the connection, click the General tab and click
Print Test Page.
You are unable to see the
printer in the Macintosh
Chooser or Print Center.
Make sure you are connected to the correct
AirPort network. See your AirPort
documentation for details.
You see a communication
error when you try to print.
You may see an error message if another
computer on your network is trying to print at
the same time. Wait until the first print job is
done. Your job will print when it reaches the
top of the print queue.
Paper jams frequently.
Try loading fewer sheets of paper.
If the test page prints, click Yes, then click OK to close the Properties
window.
If it doesn’t print, try the suggestions under “Problems?” below.
Congratulations! You’re ready for wireless printing. See Printer Basics
for more information.
When you load paper, don’t push it in.
Also, slide the left edge guide against the
paper, but not too tightly.
Use new, smooth, high-quality paper.
7
Follow the instructions on the screen to complete the wizard.
Note: For descriptions of all the settings on the Wireless
Configuration screen, see Appendix A in Setup and Installation.
8
Click Close to close the printer ports window, then click Apply
on the Properties window.
4
Enter a Server Name that is easy to remember.
9
To test the connection, select the General tab and click
Print Test Page.
5
Check that Boot Method is set to AUTO.
Click OK.
7
When you see the Wireless Server Search window again, click QUIT.
Congratulations! You’re ready for wireless printing. See Printer Basics for
more information.
1
On the EPSON® Installation Program screen, double-click Install
EpsonNet Direct Print Utility and follow the on-screen instructions
to install the utility and restart your computer.
Do one of the following:
Windows: Click Finish on the last screen. Then continue with
the instructions in the next section to set up a network port.
Mac OS X: Add the printer to Print Center or Printer Setup Utility.
(For details, see Setup and Installation.) Congratulations! You’re
ready for wireless printing. See Printer Basics for instructions.
For more problem solving tips on wireless printing, see Setup and Installation.
For printer problems, see Printer Basics.
Make sure the parallel cable is securely
connected to both the print server and your
computer.
Make sure the printer is on. Check the printer’s
lights to see if there is a problem. See Printer
Basics for details.
Unplug the AC adapter from the print server
and plug it in again. Then press the print
server’s test button for 10 seconds to reset
it to its factory defaults. If you still have
problems, contact EPSON.
If it doesn’t print, try the solutions under “Problems?” in the next
column.
Windows Me or 98
8
The print server’s status
page doesn’t print, or it
indicates that zero bytes
were transmitted
or received.
If the test page prints, click OK to close the Properties window.
Note: Always set the Boot Method to AUTO, unless you plan to
unplug the print server. See Setup and Installation for details.
6
Problems?
The Wireless Server
Search window fails to
pick up a signal from
the print server.
Test button
Make sure the print server, printer, and access
point are not near a cordless phone unit,
microwave oven, BluetoothTM device, or large
metal object. Try moving them to a new
location, or try moving them closer to
each other.
Press the print server’s test button for 10
seconds to reset it. On Macintosh, select your
wireless network again.
2
Click Start > Settings > Printers.
3
Right-click your printer icon, then click Properties. Click the Details tab.
4
Click Add Port.
Try restarting your computer.
On Macintosh, make sure that AirPort is
on, and that both AppleTalk and TCP/ IP
are enabled.
Mac OS 8.6 to 9.x: Select your C84 Series printer icon in the
Macintosh Chooser. Congratulations! You’re ready for wireless
printing. See Printer Basics for more information.
Confirm the connection between the computer
and your access point or base station. If you
have problems establishing a connection,
reset the access point or base station.
Where to Get Help
EPSON Printer Information Center
View Print Show animations that quickly tell you how to load special paper,
replace ink cartridges, and clean the print head. Also includes a User Guide
with additional printer information. To launch EPSON Printer Information
Center, double-click the EPIC or EPSON Printer Info Center icon on your
desktop.
Printer Basics
Includes instructions for printing, maintaining the printer, and solving
basic printer problems.
Setup and Installation
Provides greater detail about how to set up your printer for wireless network
printing. Includes system requirements, print server specifications, and
descriptions of settings on the Wireless Server Configuration screen.
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Here you can download drivers and other files, look at product documentation
and troubleshooting information, and receive technical advice through e-mail.
Automated Telephone Services
A variety of help services are available 24 hours a day, 7 days a week.
To use these services, you must have a touch tone telephone and call
(800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70445.
Use this code to quickly select the EPSON Stylus C84WN in SoundAdvice.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is
a trademark, and SoundAdvice is a service mark of Epson America, Inc.
continue
continue
General Notice: Other product names are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
© 2004 Epson America, Inc.
1/04 Printed in USA
CPD-17476
4 Configure the Print Server
After the files are installed, you see the Wireless Server Search window:
5 Set Up a Network Port
5
You are getting a wireless
signal, but you are not
able to print.
Make sure Network is selected, then click Browse.
You need to add the printer’s network port to each Windows computer that
will access it. If necessary, print a status page and note the server name or
IP address of your print server before you begin. For instructions on setting
up a network port on Windows NT,® see the Setup and Installation book.
Check the Wireless Server Search window to
make sure your wireless link has adequate
strength—at least 50 percent. If the signal is
weak, try moving the print server, printer, and
access point or base station closer together.
Windows XP or 2000
1
1
Windows XP: Click Start > Control Panel > Printers and
Other Hardware > Printers and Faxes.
Click START. You see server information like this:
Appears
when the
server is
found
Signal strength
Do one of the following:
Windows 2000: Click Start > Settings > Printers.
Indicates
signal strength
It may take up to 2 minutes for the server information to appear.
2
Right-click your printer icon, then click Properties.
3
On the Ports tab, select your printer (if necessary), and click Add Port.
4
Select Standard TCP/IP Port and click New Port.
6
Check the printer’s lights to see if there is a
problem with the printer. See Printer Basics
for details.
If you don’t pick up a signal from the print server, move the print server
and access point closer to each other and to the computer. If that
doesn’t work, try the solutions under “Problems?.”
2
3
When you see server information on the screen, click STOP.
Then click CONFIGURE.
When you see a message asking for a password, click OK.
You see the Wireless Configuration screen:
5
When you see the Add Standard TCP/IP Printer Port Wizard, click Next.
6
Enter your print server name or IP address and click Next.
Make sure that your network port is set up
correctly (Windows), or that you’ve added
the printer to Print Center or Printer Setup
Utility (Mac OS X) or selected the printer
in the Chooser (Mac OS 8.6 to 9.x).
Click to expand the network path, then click the + next to
Epson_Ipr and select your printer.
7
Click OK, then click OK again. Click Apply on the Details tab.
8
To test the connection, click the General tab and click
Print Test Page.
You are unable to see the
printer in the Macintosh
Chooser or Print Center.
Make sure you are connected to the correct
AirPort network. See your AirPort
documentation for details.
You see a communication
error when you try to print.
You may see an error message if another
computer on your network is trying to print at
the same time. Wait until the first print job is
done. Your job will print when it reaches the
top of the print queue.
Paper jams frequently.
Try loading fewer sheets of paper.
If the test page prints, click Yes, then click OK to close the Properties
window.
If it doesn’t print, try the suggestions under “Problems?” below.
Congratulations! You’re ready for wireless printing. See Printer Basics
for more information.
When you load paper, don’t push it in.
Also, slide the left edge guide against the
paper, but not too tightly.
Use new, smooth, high-quality paper.
7
Follow the instructions on the screen to complete the wizard.
Note: For descriptions of all the settings on the Wireless
Configuration screen, see Appendix A in Setup and Installation.
8
Click Close to close the printer ports window, then click Apply
on the Properties window.
4
Enter a Server Name that is easy to remember.
9
To test the connection, select the General tab and click
Print Test Page.
5
Check that Boot Method is set to AUTO.
Click OK.
7
When you see the Wireless Server Search window again, click QUIT.
Congratulations! You’re ready for wireless printing. See Printer Basics for
more information.
1
On the EPSON® Installation Program screen, double-click Install
EpsonNet Direct Print Utility and follow the on-screen instructions
to install the utility and restart your computer.
Do one of the following:
Windows: Click Finish on the last screen. Then continue with
the instructions in the next section to set up a network port.
Mac OS X: Add the printer to Print Center or Printer Setup Utility.
(For details, see Setup and Installation.) Congratulations! You’re
ready for wireless printing. See Printer Basics for instructions.
For more problem solving tips on wireless printing, see Setup and Installation.
For printer problems, see Printer Basics.
Make sure the parallel cable is securely
connected to both the print server and your
computer.
Make sure the printer is on. Check the printer’s
lights to see if there is a problem. See Printer
Basics for details.
Unplug the AC adapter from the print server
and plug it in again. Then press the print
server’s test button for 10 seconds to reset
it to its factory defaults. If you still have
problems, contact EPSON.
If it doesn’t print, try the solutions under “Problems?” in the next
column.
Windows Me or 98
8
The print server’s status
page doesn’t print, or it
indicates that zero bytes
were transmitted
or received.
If the test page prints, click OK to close the Properties window.
Note: Always set the Boot Method to AUTO, unless you plan to
unplug the print server. See Setup and Installation for details.
6
Problems?
The Wireless Server
Search window fails to
pick up a signal from
the print server.
Test button
Make sure the print server, printer, and access
point are not near a cordless phone unit,
microwave oven, BluetoothTM device, or large
metal object. Try moving them to a new
location, or try moving them closer to
each other.
Press the print server’s test button for 10
seconds to reset it. On Macintosh, select your
wireless network again.
2
Click Start > Settings > Printers.
3
Right-click your printer icon, then click Properties. Click the Details tab.
4
Click Add Port.
Try restarting your computer.
On Macintosh, make sure that AirPort is
on, and that both AppleTalk and TCP/ IP
are enabled.
Mac OS 8.6 to 9.x: Select your C84 Series printer icon in the
Macintosh Chooser. Congratulations! You’re ready for wireless
printing. See Printer Basics for more information.
Confirm the connection between the computer
and your access point or base station. If you
have problems establishing a connection,
reset the access point or base station.
Where to Get Help
EPSON Printer Information Center
View Print Show animations that quickly tell you how to load special paper,
replace ink cartridges, and clean the print head. Also includes a User Guide
with additional printer information. To launch EPSON Printer Information
Center, double-click the EPIC or EPSON Printer Info Center icon on your
desktop.
Printer Basics
Includes instructions for printing, maintaining the printer, and solving
basic printer problems.
Setup and Installation
Provides greater detail about how to set up your printer for wireless network
printing. Includes system requirements, print server specifications, and
descriptions of settings on the Wireless Server Configuration screen.
World Wide Web
From the Internet, you can reach EPSON Support at http://support.epson.com.
Here you can download drivers and other files, look at product documentation
and troubleshooting information, and receive technical advice through e-mail.
Automated Telephone Services
A variety of help services are available 24 hours a day, 7 days a week.
To use these services, you must have a touch tone telephone and call
(800) 922-8911. Your EPSON SoundAdviceSM Express Code is 70445.
Use this code to quickly select the EPSON Stylus C84WN in SoundAdvice.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Software is
a trademark, and SoundAdvice is a service mark of Epson America, Inc.
continue
continue
General Notice: Other product names are for identification purposes only and may be trademarks of
their respective owners. EPSON disclaims any and all rights in those marks.
© 2004 Epson America, Inc.
1/04 Printed in USA
CPD-17476
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement