ENDA EDP2041 DIGITAL POTENTIOMETER

ENDA EDP2041 DIGITAL POTENTIOMETER
english
Read this document carefully before using this device. The guarantee will be expired by
damages if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
ENDA EDP2041 DIGITAL POTENTIOMETER
Thank you for choosing ENDA EDP2041 potentiometer.
* 35x77mm sized.
* 4 digits display.
* Easy to use by front panel keypad.
* Communication via RS-485 Modbus protocol or
synchronous running between two or more potentiomers.
(Optional)
* Preset value can be adjusted from external buttons.
* Display scale can be adjusted between -1999 and 9999.
(Full scale can not be higher than a 9999)
* Decimal point can be adjusted between 1. and 3. digits.
* 0-10V,0-20 mA a and 4-20mA output with adjustable minimum and
maximum values.
* ‘Soft on’ and ‘soft off’ properties can be selected.
* Parameter access protection on 3 levels.
* CE marked according to European Norms.
Order Code : EDP2041-
TX
RX
AOUT
SET
ENDA
DIGITAL POTENTIOMETER
EDP2041
1
1- Supply Voltage
230VAC...230V AC
24VAC.....24V AC
SM...........9-30V DC / 7-24V AC
2
2- Modbus Option
RS......With RS-485 Modbus communication
Empty.....Without RS-485 Modbus communication
TECHNICAL SPECIFICATIONS
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature 0 ... +50°C/-25 ... +70°C (without icing)
80% Relative humidity for temperatures up to 31 % °C, decreasing linearly to 50% at 40°C.
Max. relative humidity
According to EN 60529
Front panel : IP65
Rated pollution degree
Rear panel : IP20
Height
Max. 2000m
Do not use the device in locations subject to corrosive and flammable gases.
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Date retention
EMC
Safety requirements
230V AC +10% -20%, 50/60Hz or 24V AC ±10% 50/60Hz or optional 9-30V DC / 7-24V AC ±10% SMPS
Max. 7VA
2.5mm² screw-terminal connections
EEPROM (Min. 10 years)
EN 61326-1: 2006 (Performance criterion B for the EMC standards)
EN 61010-1: 2010 (pollution degree 2, overvoltage category II, measurement category I)
INPUTS
Upwards input (UP)
Downwards input (DOWN)
Contact input or max. 24VDC logic input (active low)
Contact input or max. 24VDC logic input (active low)
OUTPUT
0-10V output
Digitally adjusted maximum 10mA, max. 10V potentiometer output.
Accuracy :%0.1 Resolution : 1mV
Fluctuation : Maximum 30mV
Rise time from 0 to 10V is maximum 300ms
OUTPUT
0-20mA output
Digitally adjusted maximum 12V, max.20 mA potentiometer output.
Accuracy: %0.1 Resolution : 2µA
Fluctuation : Maximum 60µA
Rise time from 0 to 20mA is maximum 300ms
HOUSING
Housing type
Dimensions
Weight
Enclosure material
Suitable for flush-panel mounting according to DIN 43 700.
W77xH35xD71mm
Approx. 350g (after packing)
Self extinguishing plastics
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
SURAN Industrieelektronik
Dettinger Str. 9 / D-72160 Horb a.N
Tel.: +49 (0)7451 / 625 617
Fax: +49 (0)7451 / 625 0650
E-mail : [email protected]
Internet : www.suran-elektronik.de
1./3
EDP2041-E
TERMS
1) Adjusted potentiometer value is seen in run mode
Parameter name, value or its unit in programming mode.
TX
RX
AOUT
2) Increment key during run mode.
Increment or parameter selection key during programming mode.
SET
3) Decrement key during run mode.
Decrement or parameter selection key during programming mode.
ENDA
EDP2041
DIGITAL POTENTIOMETER
4) Used for selecting run or programming modes and for adjusting parameters.
( 1 ) Digital display
12,5 mm 4 digits 7 segment red LED display
( 2 ),( 3 ),( 4 ) Keypad
Micro switch
DIMENSIONS
Depth
61mm
77mm
RX
AOUT
1
2
3
4
5
6
7
8
9
10
TX
5mm
Flush mounting
clamp
11 12
B
A
-
-
1
SET
Made in Turkey
241307 704086 8
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
EDP2041
SN: XXXXXXXXX
DIGITAL POTENTIOMETER
Connection
cables
Panel cut-out
2
71,5mm
ENDA INDUSTRIAL ELECTRONICS
ENDA
Rubber Panel
Flush mounting
packing
clamp
Note :
1) Panel thickness should be maximum 7mm.
2) There must be at least 60mm free space
behind the device, otherwise it would be difficult
to remove it from the panel.
To remove the device from panel:
- While pushing the the flushmounting clamp in direction 1,pull out
it in direction 2.
ENDA EDP2041 is intended for installation in control panels. Make sure that the device is used only for intended
purpose. The electrical connections must be carried out by a qualified staff and must be according to the relevant
locally applicable regulations. During an installation, all of the cables that are connected to the device must be free
of electrical power. The device must be protected against inadmissible humidity, vibrations, severe soiling.Make sure
that the operation temperature is not exceeded. The cables should not be close to the power cables or components.
ENDA INDUSTRIAL ELECTRONICS
EDP2041-230VAC
DIGITAL POTENTIOMETER
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
8 6 8 0 4 0 7 7Made
0 3 in1 Turkey
11
SN: XXXXXXXXX
8 Made
6 8in0Turkey
407 703142
-
-
1
2
3
4
5
6
7
8
NOTE :
SUPPLY :
Line
Neutral
184-253V AC 1
50/60Hz 7VA 2
9
1
11 12
10
Fuse
F 100 mA 250V AC
2
3
4
5
6
8
9
10
230V AC
Supply
Cable size: 1,5mm²
SN: XXXXXXXXX
8 680407 703166
Made in Turkey
-
B
A
11 12
1
2
3
4
5
6
7
8
9
A
11 12
10
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
Switch
Fuse should
be connected
7
EDP2041-SM-RS
DIGITAL POTENTIOMETER
9-30V DC / 7-24V AC
±10 % 7VA
B
ENDA INDUSTRIAL ELECTRONICS
Note : 1) Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the power supply switch shall bring the
identification of the relevant instrument and it should be easily accessible by the
operator.
CONNECTION DIAGRAM FOR SYNCHRONOUS RUNNING
120 Ohm
Max. 127 potentiometers
can be controlled.
4
5
6
7
8
9
10
11 12
B
241307 704086 8
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
ENDA INDUSTRIAL ELECTRONICS
1
2
3
4
5
6
7
8
9
10
A
SN: XXXXXXXXX
11 12
B
-
-
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
ENDA INDUSTRIAL ELECTRONICS
1
2
3
4
5
6
7
8
9
SN: XXXXXXXXX
10
11 12
B
A
-
-
Slave
potentiometer-2
3
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
ENDA INDUSTRIAL ELECTRONICS
1
2
3
4
5
6
7
8
9
10
A
SN: XXXXXXXXX
11 12
B
-
Slave
potentiometer-1
241307 704086 8
2
A
-
EDP2041-230VAC-RS
DIGITAL POTENTIOMETER
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
Master
potentiometer
241307 704086 8
1
241307 704086 8
Slave
potentiometer-127
NOTE :
- d.Adr. parameter should be selected C.Pot in master potentiometer. In this case d.Adr. parameter of other potentiometers aren’t used. But be sure that
C.Pot isn’t selected in slave potentiometers to prevent confusion. Settings of slave potentiometers change proportional to setting of master potentiometer.
For example; When Max. output of master potentiometer is changed from 10V to 5V, max. output of slave potentiometers decrease half of previous value
proportional to this. If previous output of slave potentiometer is 6V, it decreases 3V. P.on.c parameter of slave potentiometer should be selected oFF in
order to understand master potentiometer when slave is energized.
- Computer should be used to change only a few potentiometers. In this case, there is not master potentiomer. Output of the required potentiometer is
changed according to d.Adr. parameter.
- Baud rate of potentiometers must be same in both conditions. 120 Ohm termination resistor should be used at the ends and beginning of transmission line.
See www.enda.com.tr/EDP2041.htm for detailed information.
2./3
EDP2041-E
Run mode
Preset
value
Active
output value
PrSt.
1000
or
1001
1000
1002
1002
1003
If no key is pressed
for 3 seconds
If o.Et.y and o.d.t.Y parameters are adjusted to any value expect dSAb parameter,
output can be controlled with and buttons.
key is pressed whole in the run mode,preset setup mode is entered and PrSt. message is displayed. Message appears when the
or button is pressed, the preset value starts to flash.
By using
keys ,preset value can be adjusted.Preset value can be adjusted by using external buttons as well.External buttons become disable in programming mode.If the device is also controlled by a potentiometer,
adjustable preset value appears as above.
SET
Entering from programming mode to run mode:
If no key is pressed within 20 seconds during programming mode data is SET
stored automatically and the run mode is entered.After pressing
to the program menu by pressing
key is pressed in combination with
keys and the information is recorded.
SET
+
key is pressed while holding down to
the programming mode is entered
key
button and
then passed
SET
+
Programming mode
SET
SET
0
d.Pnt.
0
L.ScL..
9999
H.ScL.
d.PNt..= Display decimal point parameter
Decimal point can be adjusted between 1. and 3. digits.
See NOTE 1 for programming.
Off
pon.C.
L.ScL..= Lower value of the scale.Adjustable between-1999 and
(H.SCL.-10).
Scale the lower value of the output,based on o.tYP. parameter
selection, it is 0V,0mA or 4mA
See NOTE 1 for programming.
H.ScL..= Upper value of the scale.
Adjustable between (L.SCL.+10) and 9999.
DsaB
o.E.ty.
Scale the upper value of the output based on, otYP. parameter
selection;it is 10V or 20 mA. H.SCL. and L.SCL. difference can
not be greater than 9999.See NOTE 1 for programming.
0
Lo.Li.
Lo.Li..= The lower limit of the preset value.
Adjustable between L.ScL. and (Hi.Li.-10).
DsaB
o.d.ty..
See NOTE 1 for programming.
1500
Hi.Li.
Hi.Li..= The upper limit of the preset value.
Adjustable between (L.o.li.+10) and H.SCl.
See NOTE 1 for programming.
1
d.ADr.
d.Adr.=Device address for ModBus.
Adjustable between 1-247 or selectable c.Pot. .When c.Pot. is
selected,the device will be master potentiometer and slave
potentiometers can be adjusted dependent on it.
See NOTE 1 for programming
This parameter is active device with RS485 communication option.
9.60
bAud
Adjustable;off,2400,4800,9600,19200 and 38400.
This parameter is active device with RS485 communication option.
30
30
the release of the key, initial condition is returned. The same procedure is valid for the decrement
d.ti. = Decreasing time for output value.
Adjustable between 1-250 seconds.
Output is decreased slowly the lower limit
value during adjusted time.
See NOTE 1 for programming.
P.i.rt. Pi.rt.. = Increasing and decreasing speed
p.YES
U.C.sc.
U.c.Sc. = U.cnF. menu protection
p.YES
o.C.sc.
o.C.sc. = o.Cnf. Menu protection
level parameter.
nonE = No menu is seen
P.yEs = Modification feasible
P. no = Only traceable
off
menu.
This parameter should be 2041.
Security code is 0; key is pressed
continuously for 5 secoonds,dEfP
message is displayed and return to
level parameter.
nonE = No menu is seen
P.yEs = Modification feasible
P. no = Only traceable
Pno = Menu visible.
On
S.str.
Lo.li.
o.E.ty.
o.d.ti.
r.ti.
Dsab.
Dsab.
Enb.
Enb.
S.on
S.ofF
r.ti.
Lo.li.
d.ti.
It is adjustedI dSAb. ,1, 10,100 ve 1000 values.
dSAb is selected,the preset value
can not be changed.
Selected according to the value increase or
decrease the preset buttons for fast switching
mode,the preset value speedy is increased or
decreased “one by one”,10 at each step,100
at each step,1000 at each step.
key. Then, by using
is pressed and held 0.6 seconds, the value of the selected parameter
d.ti.
r.ti. = Increasing time for output.
Adjustable between 1-250 seconds.Output is
increased slowly to the lower limit value
during adjusted time.
of preset value.
SET
changes rapidly. If waited enough, the value increases 100 at each step. After 1 second following
key.
r.ti.
S.Cod = Access code for safety
U.CnF..
E.d.ty. = Returning method of the output to
preset value with the external "Down" input.
o.d.tY. is set like the output parameter.
P.on.C.
S.Cod.
button
E.d.ty..
keys, adjustment can be made.
If increment key
o.d.ty. = Adjusted type of the output to lower limit value with
button.
dSAb.= Output can not be adjusted to lower limit value with
button.
Enb. = Output can be adjusted to lower limit value with button.
S.oFF = Output is increased to voltage that lower limit value is displayed with
during dtI.
See NOTE 1 for programming.
DsaB
1
For adjusting a selected parameter first press and hold
button during r.tI
E.E.ty. = Returning method of the output to preset value with the external "Up" input.
o.E.tY. is set like the output parameter.
Parameter adjustment method
SET
o.E.ty. = Adjusted type of the output to preset value with
button.
dSAb.= Output can not be adjusted to preset value with
button.
Enb. = Output can be adjusted to preset value with
button.
S.on = Output is increased to voltage that set value is displayed with
See NOTE 1 for programming.
E.E.ty..
While the parameter names appear,
and
keys are
pressed together,the program will return to the menu display.
SET
P.on.C. = Selection of the output parameter behavior
ofF= When first energized, output is the voltage or current that lower limit value is indicated.
Attention: If this parameter is selected, the set value that was adjusted before is seen when set button is
pressed at first. In addition,if increasing or decreasing that value is wanted the set value is equalized to
lower limit value and then adjustment can be done.
On= When first energized, output is the voltage or current hat the set value is indicated.
S.Str.= When first energized, output is increased slowly from the voltage or current that lower limit value is
indicated to the voltage or current that set value is indicated during r.ti.
See NOTE 1 for programming.
DsaB
baud = Baud rate for the RS485 connection.
o.cnF.
NOTE 1
SET
SECu.
o.CnF.
U.CnF..
0-10
SEcu.
o.typ.. o.tyP.. = Output type selection parameter
0-10 = 0-10V output usable
4-20 = 4-20mA output usable
0-20 = 0-20mA output usable
See NOTE 1 for programming
E.E.ty.
E.d.ti.
Lo.li.
Dsab.
Dsab.
Enb.
Enb.
S.on
S.ofF
r.ti.
d.ti.
3./3
EDP2041-E
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement