"user manual"

"user manual"
User Manual
June 2009
Ord. No.
050-900
050-901
050-902
050-903
050-904
Model
T1 Thermocycler 48
T1 Thermocycler 96
T1 Thermocycler 384
T1 Thermocycler in situ
T1 Thermocycler combi
!! Warning !!
Please read these instructions carefully before using this
apparatus!
Biometra GmbH
Rudolf-Wissell-Str. 30
D-37079 Göttingen
Tel.: +49 551-50686-0
Fax: +49 551-50686-66
email: [email protected]
Internet: http://www.biometra.com
Service Department
Rudolf-Wissell-Strasse 14-16
D-37079 Göttingen
Tel.: +49 551-50881-10/12
Fax: +49 551-50881-11
email: [email protected]
Manual T1 Thermocycler June 2009
2 __________________________________________________________________________
1
Introduction ...........................................................................................................................4
2
Before you start.....................................................................................................................5
2.1
3
Safety precautions.........................................................................................................5
First steps with the T1 Thermocyler ......................................................................................6
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4
The T1 Thermocyler front View .....................................................................................6
The T1 Thermocyler rear view ......................................................................................7
The T1 Thermocycler control panel...............................................................................8
Initial self test.................................................................................................................9
The T1 Thermocycler display ........................................................................................9
Handling of the adjustable heated Lid ...........................................................................9
Releasing wheel in case of blocked lid........................................................................10
Creating a Program.............................................................................................................11
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5
Select a directory.........................................................................................................11
Select a program store ................................................................................................11
Enter name for subdirectory ........................................................................................12
Enter a program name ................................................................................................12
Enter the lid temperature.............................................................................................13
Select / deselect pre-heating of the lid ........................................................................14
Enter temperature and time settings ...........................................................................14
Set cycle number.........................................................................................................15
Cool below ambient temperature ................................................................................16
Save program..............................................................................................................16
View/edit program data .......................................................................................................17
5.1
5.2
5.3
6
Delete / insert program steps ......................................................................................17
Copy program..............................................................................................................18
Delete program............................................................................................................19
Further programming options..............................................................................................21
6.1
6.2
6.3
7
Program time increments ............................................................................................21
Program touch down ...................................................................................................22
Adjust heating and cooling rates .................................................................................22
Run Program.......................................................................................................................23
7.1
7.2
7.3
7.4
8
Select and start program .............................................................................................23
Display during operation..............................................................................................24
View remaining run time..............................................................................................25
Pause / stop program ..................................................................................................25
Special functions .................................................................................................................27
8.1
8.2
8.3
8.4
9
10
Print protocols .............................................................................................................27
Switch beep on/off.......................................................................................................27
Select language...........................................................................................................28
RS232 Control.............................................................................................................28
Maintenance........................................................................................................................29
Exchange of modules......................................................................................................29
Manual T1 Thermocycler June 2009
____________________________________________________________________________ 3
11
11.1
11.2
11.3
11.4
12
12.1
12.2
Trouble shooting............................................................................................................. 30
Slow heating and cooling............................................................................................ 30
Restart due to unrecognized power failure ................................................................. 30
Adaptation of protocols from other cyclers ................................................................. 30
Recommendations for the use of 384 well Thermocyclers ......................................... 30
Appendix......................................................................................................................... 31
Technical specifications T1 Thermocycler 96............................................................. 31
Ordering information ................................................................................................... 31
13
Instructions for return shipment ...................................................................................... 32
14
Warranty ......................................................................................................................... 33
15
Equipment Decontamination Certificate ......................................................................... 34
16
EU - Konformitätserklärung / EU - Declaration of Conformity ........................................ 35
17
Subject Index.................................................................................................................. 36
Manual T1 Thermocycler June 2009
____________________________________________________________________________ 4
1 Introduction
The T1 Thermocycler was designed to meet the highest standard of a today molecular biology
laboratory. The instrument combines the very successful Biometra silver block concept with an
advanced block architecture. The result is a Thermocycler that provides extremely high
temperature ramping rates and an unrivalled temperature uniformity. High ramping rates ensure
specific reation and the perfect temperature uniformity guarantees identical conditions in any
position of the block.
The T1 Thermocyler is available with different modules that support a broad range of tubes,
strips and microplates. There is also an in situ-modul for up to 4 microscopic slides.
The T1 Thermocyler is adjusted to match the BIOMETRA TGradient cycling characteristics.
Thus protocols, that have been optimized with a TGradient, can be operated without the need
for modifications. This makes the T1 the perfect instrument to increase sample throughput
togehter with an existing Tgradient.
Manual T1 Thermocycler June 2009
____________________________________________________________________________ 5
2 Before you start
2.1 Safety precautions
Please read this manual carefully before starting operation of the T1 Thermocycler.
•
General safety precautions for laboratory work must be observed when working with the T1
thermocycler.
•
Be aware that samples are reaching high temperatures. Do not touch or open hot tubes or
microplates, because hot liquid may quickly spill out.
•
Do not heat samples without having the lid locked securely.
•
Before opening of the lid, release lid pressure (see section 3.6)
•
Do not place fingers between lid and housing when opening or closing the lid.
•
Do not touch the heated lid.
•
When only few samples are put in the block place additional tubes in the four corner
positions. This is to evenly distribute the lid pressure and prevents single tubes from
excessive pressure. Use of few tubes may result in damage of the tubes by excessive
pressure.
•
Use only suited plastic ware in the T1 thermocycler. Tubes and plates must show good fit
when placed in the thermoblock. Only use tubes that are suited for high temperatures (tight
lids).
•
The T1 Thermocyler contains no user serviceable parts. Do not open the housing
instrument. Service and repair may only be carried out by the Biometra Service department
or otherwise qualified technical personal.
•
Do not use the instrument when damages of the housing, block, cable or other parts are
visible.
•
The T1 Thermocycler must not be used with explosive, flammable or volatile liquids.
•
Appropriate safety regulations must be observed when working with infectious or pathogenic
material.
The thermoblock and the heated lid will reach high temperatures
during operation. Both thermoblock and heated lid can burn you.
Rapid heating of the thermoblock can cause liquids to boil
explosively. Always wear safety goggles during operation. Close the
lid before starting a program.
It is not necessary to apply oil into the opening of the block in order
to improve the heat transfer between the block and the sample
tubes.
If you still decide to use oil, do not use silicon oil. Mineral oil may be
used.
Manual T1 Thermocycler June 2009
6 __________________________________________________________________________
3 First steps with the T1 Thermocyler
3.1 The T1 Thermocyler front View
Knob for release
of the lid
Wheel for the height
adjustement
of the heated lid.
Keypad
Graphical display
Power switch
Manual T1 Thermocycler June 2009
____________________________________________________________________________ 7
3.2 The T1 Thermocyler rear view
Parallel
printer port
RS-232
port
Fuse holder
for 2 fuses,
for specifications of fuses
see type label on the
instrument´s backside
Manual T1 Thermocycler June 2009
Power cord
plug
Type label including:
serial number
specifications of fuses
8 __________________________________________________________________________
3.3 The T1 Thermocycler control panel
Graphical display
Power
Power switch:
backlit = power on
A
B
C
D
Function keys:
the corresponding functions are
specified in the screen.
7
8
9
4
5
6
1
2
3
.
0
-
Easy to clean
keyboard
Cursor keys:
For free navigation in the
programming spreadsheet.
Use to scroll through lists.
Manual T1 Thermocycler June 2009
____________________________________________________________________________ 9
3.4 Initial self test
After switching on the T1 Thermocyler the serial number of the instrument and the software
version is displayed.
T1 Thermocycler
Serial No 1234567
Vers. 5.01t1
The T1 Thermocyler checks the programs in all directories (so called RAM check).
3.5 The T1 Thermocycler display
The T1 Thermocyler display provides information about the instrument and about the status of
the active program.
prog
step
temp[°C]
time
lid
A ?
25.2°C
25.4°C
B start/stop
C programs
D +
The individual function of the special keys A , B , C and D are specified in the display and
depend on the context.
3.6 Handling of the adjustable heated Lid
To achieve optimum pressure on the tubes the T1 Thermocyler is equipped with an height
adjustable heated lid (smart lid technology).
Close the lid:
After the samples have been placed in the block close the lid. Turn the wheel clockwise until
you hear a clicking noise. In this mode, the pressure will not increase further, even when you
keep on turning the wheel.
Note: The pressure of the lid has been optimize for a fully loaded block. If only very few tubes
are loaded to the block you should place dummy tubes in the four corner positions to avoid
damage of tubes by excessive pressure.
Open the heated lid:
First: Release pressure by turning the wheel counter clockwise. As soon as there is no more
resistance the pressure has been released. Then: now you can open the lid with the knob.
Important: The lid must not be opened under pressure because this leads to damage of the
locking mechanism.
Manual T1 Thermocycler June 2009
10 _________________________________________________________________________
3.7 Releasing wheel in case of blocked lid
Note: When the lid is in the extreme up or down position, it may happen that the wheel is
uncoupled. In this situation the clutch mechanism is active in both directions (clicking noise in
either direction). To unlock wheel, press metal pin with a ballpen and turn wheel carefully. This
pin overcomes the automatic clutch mechanism. Thus, care must be taken not to apply
excessive pressure.
Lid arrested in upper
position:
carefully turn wheel with
pressed pin clockwise, until
you feel normal resistance
(no more clicking noise,
clutch is released). Release
pin and turn lid down, until
the clutch mechanism is
activated (clicking noise,
optimum pressure applied).
Lid arrested in down
position:
carefully turn wheel with
pressed pin counter
clockwise, until you feel
normal resistance (no more
clicking noise, clutch is
released). Release pin and
turn wheel counter clockwise
until pressure is completely
released. Open lid.
IMPORTANT: WHEN THE CLUTCH MECHANISM IS ACTIVE (OPTIMUM PRESSURE IS
APPLIED), NEVER USE PIN TO FURTHER INCREASE PRESSURE. THIS WILL LEAD TO
DAMAGE OF TUBES AND INSTRUMENT!
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 11
4 Creating a Program
4.1 Select a directory
In the T1 Thermocyler programs can be stored both in the main directory and in individual
subdirectories. For easy identification of the selected storage place, the subdirectories can be
named (see section 4.3).
Start with the main screen.
Prog
step
temp[°C]
time
lid
A ?
25.2°C
25.4°C
B start/stop
C programs
D +
Press [C programs] to enter the edit mode.
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
A ?
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
You are now in the main directory. The structure of the subdirectories is displayed.
4.2 Select a program store
Programs can be stored in the main directory or in subdirectories.
To create a program in the main directory press [D enter].
To access a subdirectory move right with the cursor key Ö and select a subdirectory with the
cursor keys ×Ø. The selected directory will be highlighted.
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
A ?
Manual T1 Thermocycler June 2009
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
12 _________________________________________________________________________
4.3 Enter name for subdirectory
The process for naming a subdirectory and a program is the same. For information about
naming programs see section 4.4.
Press [D enter] to enter the highlighted subdirectory
directory:
program no.
edit
A list
5
Name:
B
C quit
D enter
Press [A list] to view a list of all existing files and empty memory in this directory.
Note: If neither program name nor the word “empty” is displayed, this place may be occupied by
a program without name. For the programming of new protocols choose an empty memory.
Existing programs that are not needed any more can be deleted to provide new memory.
0
1
2
3
4
A
empty
empty
empty
empty
empty
list
B forward
C quit
D enter
Scroll through the list with cursor keys ×Ø and confirm memory with [D enter].
4.4 Enter a program name
Each program is specified by a program number and a subdirectory number. To make retrieval
of a program easier, you can enter a name for each program existing of letters, numbers and
symbols.
Directory:
program no.
A ABC
3
0
Name:
B files
∧
ABCDEFGHIJKLMNOPQRST
UVWXYZ-()#°C/,〈〉&+.%!
C name OK
D enter
To enter a name for your program press [A ABC].
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 13
Directory:
program no.
A name
3
0
B blank
Name:
∧
ABCDEFGHIJKLMNOPQRST
UVWXYZ-()#°C/,〈〉&+.%!
C quit
D enter
Choose a letter from the alphabet with cursor keys ÕÖ×Ø
Confirm each letter with [D enter].
Directory:
program no.
A name
3
0
B blank
Name:
T
∧
ABCDEFGHIJKLMNOPQRST
UVWXYZ-()#°C/,〈〉&+.%!
C name OK
D enter
The selected letter will appear in the display and the cursor will move one step to the right.
Select the next letter and confirm with [D enter].
Note: What to do, if a wrong letter has been accepted?
To alter the position of the cursor within the name press [A name]. Now you can move the
cursor with cursor keys ÕÖ through the name. This is helpful if you have confirmed an wrong
letter or if you want to change the name of an existing program.
Once the name is complete, confirm name with [C name OK].
Directory:
program no.
lid temp:
edit
A ?
3
0
°C
B files
Name:
TEST 1
preheating: on
C pgm OK
D enter
4.5 Enter the lid temperature
Note: Thanks to a new lid design, significantly lower lid temperatures than in the past can be
used for thermocycling. The lower lid temperature leads to a higher temperature uniformity
within the lid and thus to a more even temperature distribution in the tubes.
For instruments featuring the new lid design, a maximum temperature of 99.0°C should be
used.
Manual T1 Thermocycler June 2009
14 _________________________________________________________________________
Directory:
3
program no.
0
lid temp:
99 °C
edit
A ?
Name:
TEST 1
preheating: on
B files
C pgm OK
D enter
4.6 Select / deselect pre-heating of the lid
You can choose whether the lid is pre-heated before the program starts. This is to avoid
evaporation during the initial heating phase. Note: During the preheating of the lid, the block is
held constant at 25°C.
Directory:
3
program no.
0
lid temp:
99 °C
edit
A on/off
Name:
TEST 1
preheating: on
B files
C pgm OK
D enter
Note: The default setting, which is recommended for most applications, is preheating: on.
After all pre-settings have been made, press [D enter] to open the programming spreadsheet.
4.7 Enter temperature and time settings
The programming spreadsheet:
Temp[°C]
1
2:
3:
4:
A ?
time
Å
opt Æ
#
B insert/delete
C pgm OK
D enter
Note: In this spreadsheet you can enter all parameters for your cycling protocol. Furthermore,
you can set special parameters like touch down, ramping rates or time increments. For further
details on these special parameters, see section 6.
Note: You can navigate in the spreadsheet without limitations with the four cursor keys ÕÖ×Ø.
Note: Each setting is confirmed with [D enter]. The cursor moves automatically to the next field.
Alternatively, you can confirm a value by moving forward with the cursor keys.
Note: At any time you can call up the help function with [A ?]
Note: In an existing protocol hole program steps can be deleted and inserted. For further
information on deleting and inserting program steps see section 5.1.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 15
Now enter temperature for the first step in the protocol:
Temp[°C]
time
Å
#
1
65,0
2:
3:
4:
A ?
B insert/delete
opt Æ
C pgm OK
D enter
Confirm temperature with [D enter] or just move on with the cursor key. If you move to the next
row, the setting will be stored in the temporary memory.
Temp[°C]
1
65.0
2:
3:
4:
A ?
time
Å
opt Æ
#
B insert/delete
C pgm OK
D enter
Enter a time for step one.
Note: There is a convention on how time settings are entered in all BIOMETRA cyclers:
hours z minutes z seconds
If you enter a number without “dot” this value will be interpreted as seconds (“300” => 5
minutes). To program minutes enter a “z” after the number of minutes. To enter hours enter z
z after the number. You can also enter any combination of hours, minutes and seconds.
Example: for 1 hour, 30 minutes, 20 seconds enter 1z 30 z 20.
The time values will be displayed in the following format: 0h 00 m 00s
Accept time setting with [D enter] or move to the next field with cursor key.
4.8 Set cycle number
Note: In general, loops are defined by selecting the target for the back loop and the number of
backloops.
Temp[°C]
1: 65.0
2: 65.0
3: 80.0
4: 35.0
A ?
time
Å #
0h 5m 0s
0h 0m30s
0h 0m30s
0h 0m30s
2
B insert/delete
opt Æ
C pgm OK
D enter
In the column labeled with Å you can select the target step for a backloop.
Manual T1 Thermocycler June 2009
16 _________________________________________________________________________
Temp[°C]
1: 65.0
2: 65.0
3: 80.0
4: 35.0
A ?
time
Å #
0h 5m 0s
0h 0m30s
0h 0m30s
0h 0m30s 2
29
B insert/delete
C pgm OK
opt Æ
D enter
Enter the number of backloops. Note: total cycler number = (n backloops) + 1, e.g. enter 29 for
a total number of 30 cycles.
4.9 Cool below ambient temperature
Temp[°C]
2: 65.0
3: 80.0
4: 35.0
5: 4.0
A ?
time
Å #
0h 0m30s
0h 0m30s
0h 0m30s 2
29
pause
B insert/delete
C pgm OK
opt Æ
D enter
To hold the temperature for an indefinite time enter “0”. After pressing [D enter] “pause” is
displayed.
Note: The minimum temperature you can set is –3°C.
4.10 Save program
Save program with [C pgm OK]. The program data are stored in the permanent memory.
Directory:
3
program no.
0
number of steps: 5
runtime:
1h10m23s
edit
A
B
Name:
C
TEST 1
D
The runtime is calculated and displayed.
Note: To view the current remaining runtime at any time of the run press [A info] in the main
menu.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 17
5 View/edit program data
You can check any existing program by scrolling through the editing mode with cursor keys
ÕÖ×Ø. Select the desired program as described in section 4.2.
Note: During operation of the cycler the active program can be viewed but not modified. If you
want to change settings of the active program for further experiments you have to save a copy
of this program to another memory. For further information about copying programs see section
5.2.
5.1 Delete / insert program steps
The programming spreadsheet:
Temp[°C]
time
Å #
2: 65.0 0h 0m30s
3: 80.0 0h 0m30s
4: 35.0 0h 0m30s 2
29
5:
A ?
B insert/delete
opt Æ
C pgm OK
D enter
To delete or insert a program step press [B insert/delete]
insert /
2: 65.0
3: 80.0
4: 35.0
5:
A ?
delete step:
0h 0m30s
0h 0m30s
0h 0m30s 2
29
B delete input
C quit
D enter
Enter the number of the step that you want to insert / delete.
Note: Additional steps will be inserted before the selected step number. The following steps will
be shifted by one position.
insert /
2: 65.0
3: 80.0
4: 35.0
5:
A ?
delete step:
0h 0m30s
0h 0m30s
0h 0m30s 2
3
29
B delete input
C quit
D enter
Note: If you have entered a wrong number, the field can be cleared with [B delete input].
Confirm the step number with [D enter].
Manual T1 Thermocycler June 2009
18 _________________________________________________________________________
insert / delete step:
2: 65.0 0h 0m30s
3: 80.0 0h 0m30s
4: 35.0 0h 0m30s 2
5:
A insert
B delete
3
29
C quit
D enter
Press [A insert] to insert one step at the selected position.
Note: Additional steps will be inserted before the selected step. The following steps will be
shifted by one position.
Press [B delete] to delete the selected step.
Note: By deleting a step the following steps will be shifted by one position.
Note: The insertion and deletion of steps may have an influence on existing cycles. Be sure
that all settings are updated to maintain a correct cycle.
5.2 Copy program
Select the program you want to copy as described in section 4.1 and 4.2
Directory:
program no.
lid temp:
A ?
3
0
99°C
Name:
TEST 1
preheating: on
B files
C pgm OK
D enter
Press [B files].
Directory:
program no.
lid temp:
edit
A copy
3
0
°C
Name:
TEST 1
preheating: on
B delete pgm
C quit
D enter
To copy this program to another memory press [A copy]
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
copy to:
A ?
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
Select the desired subdirectory with the cursor keys Ö× Ø. The selected subdirectory will
highlight.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 19
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
copy to:
A ?
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
Confirm your selection with [D enter].
copy from directory 3 program 0
to
directory 6 program
A list
B
C quit
D enter
Choose an empty memory from the list with [A list].
copy from directory 3 program 0
to
directory 6 program 6
enter = OK
target program contains
A list
B
0 steps
C quit
D enter
Note: Before you confirm with [D enter] the target memory is checked. If there is no program in
the target, memory the message “ target program contains 0 steps” is displayed. If the memory
already contains a program the number of steps is displayed.
Note: If you copy a program to a memory that already contains a program, the former program
will be deleted!
Save a copy of the program in the new directory with [D enter].
5.3 Delete program
Select program as described in section 4.1 and 4.2
Directory:
program no.
lid temp:
edit
A copy
3
0
°C
B delete pgm
To delete this program press [B delete pgm].
Manual T1 Thermocycler June 2009
Name:
TEST 1
preheating: on
C quit
D enter
20 _________________________________________________________________________
Directory:
program no.
lid temp:
3
0
°C
Name:
TEST 1
preheating: on
delete program 0?
A copy
B delete pgm
enter = yes
C quit
D enter
Confirm your selection with [D enter].
Note: Once you have deleted a program it cannot be restored!
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 21
6 Further programming options
Temp[°C]
1: 65.0
2: 65.0
3: 80.0
4: 35.0
A ?
time
Å
0h 5m 0s
0h 0m30s
0h 0m30s
0h 0m30s
2
B header
opt Æ
#
C pgm OK
D enter
Note: To program special parameters you can scroll the display to the right.
Move the cursor to the right side of the display that is labeled with opt Æ.
The following screen will appear:
Main funct.
dT[°C]
1: Å
2: Å
3: Å
4: Å
A ?
B header
dt[s]
C pgm OK
Ê[°/s]
5.00
5.00
5.00
5.00
D enter
Note: To get back to the screen with the basic parameters move the cursor to the left side of
the display labeled with “Main funct.” Alternatively you can move the cursor to the extreme right.
Temp[°C]
1: 65.0
2: 65.0
3: 80.0
4: 35.0
A ?
time
Å
0h 5m 0s
0h 0m30s
0h 0m30s
0h 0m30s
2
B header
opt Æ
#
+
C pgm OK
D enter
Note: In the main screen you will find an information that a special parameter has been
modified. This is indicated by a + in the row labeled with opt Æ.
6.1 Program time increments
To compensate for loss in enzyme activity each step within a loop can be extended from cycle
to cycle. Enter the desired time increment [seconds] in the row labeled with dt[s]. This value will
be added to the time value from cycle to cycle.
Main funct.
dT[°C]
2: Å
3: Å
4: Å
5: Å
A ?
B header
Manual T1 Thermocycler June 2009
dt[s]
10
C pgm OK
Ê[°/s]
5.00
5.00
5.00
5.00
D enter
22 _________________________________________________________________________
Note: The time increment will have an impact on the total runtime depending on the numbers of
cycles and the size of the increment. A program with many cycles and large time increments will
take a significantly longer time than a standard protocol.
6.2 Program touch down
For some applications it is useful to start with a higher temperature and to decrease the
temperature from cycle to cycle. This subsequent lowering of the temperature is called touch
down.
To decrease a temperature from cycle to cycle enter a negative temperature increment in the
row labeled with dT[s].
Main funct.
dT[°C]
2: Å
3: Å
4: Å
-0.20
5: Å
A ?
B header
dt[s]
C pgm OK
Ê[°/s]
5.00
5.00
5.00
5.00
D enter
Note: Be sure that the temperature decrease is set in a step that lies within a loop. Otherwise
there will be no iterative temperature decrease.
6.3 Adjust heating and cooling rates
Since the T1 Thermocyler is a extremely fast Thermocycler it may be necessary to reduce the
heating and cooling ramp for some applications. For example this is helpful if cycling protocols
from other cyclers shall be used.
The heating or cooling ramp respectively can be set in the row labeled with Ê[°/s].
Main funct.
dT[°C]
2: Å
3: Å
4: Å
5: Å
A ?
B header
dt[s]
C pgm OK
Ê[°/s]
5.00
5.00
5.00
5.00
D enter
Note: The default is [5.00 °/s], which means maximum ramping speed.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 23
7 Run Program
7.1 Select and start program
Main display:
Prog
step
temp[°C]
time
lid
A ?
25.2°C
25.4°C
B start/stop
C programs
D +
To select a program press [B start/stop]
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
start
A ?
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
Choose directory with cursor keys Ö × Ø or enter main directory with [D enter]
Note: The path for the program that was modified most recently is automatically pre-selected
⏐-3.
⏐-4.
Main direct.--- ⏐-5.
⏐-6.
⏐-7.
A ?
B
subdirect.:
subdirect.:
Subdirect.:
subdirect.:
subdirect.:
C quit
D enter
Enter subdirectory with [D enter]
Directory: 5
program no.
Edit
A list
B
Name:
C quit
D enter
Enter the number of the program you want to start. Alternatively, [press A] list to select a
program from the list of all programs in this subdirectory.
Scroll through the list with cursor keys × Ø.
Manual T1 Thermocycler June 2009
24 _________________________________________________________________________
0
1
2
3
4
A
test 1
empty
empty
empty
empty
list
B forward
C quit
D enter
Confirm highlighted program with [D enter].
The number and name of both subdirectory and the selected program will be displayed.
Directory:
program no.
3
0
Name:
TEST 1
preheating lid on
signal on
C quit
D start
start block
A list
B
To start the program press [D start].
7.2 Display during operation
During preheating of the lid the following screen is displayed:
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
1
25.0°C
preheating
B start/stop
dir 3
Æ 65.0
C programs
D +
Note: In the default setting (preheating on) the block is held constantly at 25°C. The program
starts as soon as the lid has reached the set temperature. During the preheating phase the
display of the lid temperature alternates between the current lid temperature and “preheating”.
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
1
25.0°C
dir 3
Æ 65.0
preheating
B start/stop C programs
D +
As soon as the block has reached the programmed hold temperature, the timer starts to count
down.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 25
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
1
65.0°C
0h 2m15s
98.9°C
B start/stop
dir 3
cycle 1 of 30
Æ 65.0
Æ0h 5m 0s
C programs
D +
The elapsed time versus programmed hold time is displayed
7.3 View remaining run time
Display during operation:
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
dir 3
1
cycle 1 of 30
80.0
Æ 80.0
0h 0m23s
Æ0h 5m 0s
98.9°C
B start/stop
C programs
D +
Press [A info] to call up the current remaining time calculation.
Additional information about active pgm
Status:
Step 2
Cycle 3 of 30
Remaining time: 2h 57m
Stop or pause: key B in main menu
A
B
C quit
D
The current remaining run time id displayed in line 4.
7.4 Pause / stop program
Main display during operation:
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
1
35.0°C
0h 0m18s
98.8°C
B start/stop
dir 3
cycle 8 of 30
Æ 35.0
Æ0h 0m30s
C programs
D +
To pause or stop the active program press [B start/stop]
Stop/pause
directory:
program no:
A ?
Manual T1 Thermocycler June 2009
3
0 test 1
B pause
C quit
D stop
26 _________________________________________________________________________
Select
[B pause]
[D stop]
[C quit ]
to pause program
to stop program
to return to the program display
When you select [B pause], the following screen is displayed:
Prog
Step
temp[°C]
time
lid
A info
0 TEST 1
1
35.0°C
98.8°C
B start/stop
dir 3
cycle 8 of 30
Æ 35.0
pause
C programs
D +
The program pauses in the current state. The word pause is displayed and alternates with the
elapsed time. You can proceed with the program with [B start/stop].
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 27
8 Special functions
Main screen
Prog
step
temp[°C]
time
lid
A ?
25.2°C
25.4°C
B start/stop
C programs
D +
To change special features of the T1 Thermocyler press [D +].
1 print
2 signal
3 language
4 standard mode
5 test mode
A back
B forward
C quit
D enter
Scroll though the list with the cursor keys × Ø. Enter desired function with [D enter]
8.1 Print protocols
1
2
3
4
graphic protocol*
graphic protocols*
print program
print all programs
A
B
C quit
D enter
Scroll through the list with the cursor keys × Ø. Confirm the highlighted function with [D enter].
8.2 Switch beep on/off
There is an option for an audible signal whenever a program enters a pause and when the
program is finished. If this option is active, the beep can be switched off by pressing any key of
the keyboard.
with signal
A
yes
no
B
C quit
D enter
In this window you can select whether there is a signal or whether there is not. Using the cursor
keys you can toggle between signal yes/no. Confirm your selection with [D enter].
Manual T1 Thermocycler June 2009
28 _________________________________________________________________________
8.3 Select language
The display of the T1 Thermocyler can be switched from English to German. Select language
with cursor keys Ø ×. As you toggle between the two settings the language will change.
language
A
German
English
B
C quit
D enter
To confirm your selection press [D enter]
8.4 RS232 Control
The T1 Thermocylcer can be programmed and controlled by a Personal Computer. The
Tcontrol iT software is available with the order number 050-820. To acivate remote control, the
T1 Thermocylcer has to be set to RS232 control mode.
For detailled information on controlling T1 Thermocylcer with PC please refer to the Tcontrol iT
manual.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 29
9 Maintenance
The T1 Thermocyler was built to operate for a long time without the need for periodical
maintenance. The housing may be cleaned from time to time with a smooth cotton cloth. Do not
use strong detergents or organic solvents for cleaning.
10 Exchange of modules
For exchange of modules you need two hexagonal keys (number 3 and number 5). These keys
are included in the shipment of the module.
Remove module
Â
Â
Â
Â
Â
Â
Remove power plug
Place instrument upside down on a soft surface
Remove the 2 screws that close the shutter (hexagonal key number 3)
Remove the 4 screws that hold the block (hexagonal key number 4)
unplug connectors from the block (control and power supply)
remove module
Install module
Follow description in reversed order.
Manual T1 Thermocycler June 2009
30 _________________________________________________________________________
11 Trouble shooting
11.1 Slow heating and cooling
The T1 Thermocyler is equipped with a strong ventilator for the cooling of the heat sink. The
inlet of this fan is located at the bottom side of the instrument. Be sure that the inlet is not
clogged by dust or other material (e.g. a sheet of paper placed under the cycler can be attached
to the inlet as the fan is in operation). Dirt can be removed easily from the inlet with a
conventional vacuum cleaner.
11.2 Restart due to unrecognized power failure
High voltage fluctuation can lead to an automatic restart of the Thermocycler. In this case the
cycler restarts at the step where there power failure has occurred. To avoid voltage fluctuation,
do not connect the cycler to a socket shared by a strong power consumer like a refrigerator or a
centrifuge.
11.3 Adaptation of protocols from other cyclers
Since the T1 Thermocyler is an extremely fast Thermocycler it may be necessary to reduce the
heating and cooling ramps to run protocols from other cyclers. For the setting of the heating and
cooling ramps see section 6.3. Alternatively, the time settings may be extended.
Note: Protocolls that have been optimized with a TGradient Thermocycler can be run without
changes.
11.4 Recommendations for the use of 384 well Thermocyclers
a) Use the recommended 384 well plates and sealing materials
To prevent sample evaporation by insufficient sealing please use 384 well plates and sealings
tested and recommended by Biometra. A list of plates and sealing is available at
www.biometra.com -> thermocyclers -> plasticware
b) Reduce the temperature of the heated lid
Due to the fact that the heated lid is very close to the reaction volume with a 384 well plate
compared to 0.2 ml vessels the lid temperature can have a significant impact on the effective
incubation temperature. For reaction volumes less than 10 µl the lid temperature is
recommended to be set at 95 °C. When using a reaction volume of 10 µl or more, set lid
temperature at 85 °C. Even at these lowered lid temperatures possible condensation will not
occur as problem due to a mixture of physical factors like dew point, salt concentration,
temperature difference, air pressure within the tube and reaction volume. It is strongly
recommend to reduce the lid temperature according to the reaction volume. Otherwise, at
conventional lid temperature settings, sample volumes or amplification yields might be reduced.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 31
12 Appendix
12.1 Technical specifications T1 Thermocycler 96
Thermal range
Temperature accuracy
Thermal homogeneity
Maximum heating speed
Max. cooling speed
Sample capacity
Heated lid
Line Voltage
Frequency
Power consumption
Fuses
Display
Ports
-3°C – 100°C
+ 0.1°C
+ 0.3°C within 15 sec.
4°C/sec.
3°C/sec.
96 x 0.2ml tubes, 96 well microplates, strips
High Precision Smart Lid for optimum lid pressure and
excellent temperature uniformity
Lid temperature range 30.0 – 99.0°C
115 Volt or 230 Volt
50-60 Hz
310 watts maximum
see label on the back of the instrument
LCD graphical display, back-lit
serial: RS232 (bi-directional data transfer)
parallel: Centronics (printer)
Port for in tube-sensor
memory
Total capacity: 1500 steps
in 10 directories with maximum 100 programs each
Dimensions (WxDxH)
Weight
Storage conditions
Operating conditions
25 x 34 x 16,5 cm
8,8 kg
5°C – 35°C
10 – 90% humidity
12.2 Ordering information
T1 Thermocyler
T1 Thermocyler 48 for 48 x 0.5ml tubes
T1 Thermocyler 96 for 96 x 0.2ml tubes, strips or 96 well microplates
T1 Thermocyler 384 for 384 well microplates
T1 Thermocyler in situ for 4 microscopic slides
T1 Thermocyler Modules
T1 Thermocyler 48 Module for 48 x 0.5ml tubes
T1 Thermocyler 96 Module for 96 x 0.2ml tubes, strips or 96 well
microplates
T1 Thermocyler in situ Module for 4 microscopic slides
Order-No.
050-800
050-801
050-802
050-803
050-810
050-811
050-813
For information about tubes, strips, microplates and other consumables please contact
BIOMETRA or your local BIOMETRA distributor.
Manual T1 Thermocycler June 2009
32 _________________________________________________________________________
13 Instructions for return shipment
In case of faults occurring with our T1 Thermocyler please proceed as follows:
• Return only defective devices. For technical problems which are not definitively recognizable
as device faults please contact the Technical Service Department at Biometra (Tel.:
+49/551/5068640, Fax: ++49/551/5068666, e-mail: [email protected]).
• Important: Cleanse all parts of the instrument of biologically dangerous, chemical or
radioactive contaminants. If an instrument is contaminated, Biometra will be forced to refuse
to accept the device. The sender of the repair order will be held liable for possible losses
resulting from insufficient decontamination of the device.
• Please prepare written confirmation that the device is free from biologically dangerous and
radioactive contaminants. The declaration of decontamination (see 15) has to be attached to
the outside of the packaging.
• Use the original packing material. If not available, please use a comparable robust box. Be
sure that the instrument fits tightly into the box. When packaging, protect the device in a way
to avoid scratches.
• Label the outside of the box with “CAUTION! SENSITIVE ELECTRONIC INSTRUMENT!”
• Please enclose a note which contains the following:
a) Sender’s name and address,
b) Name of a contact person for further inquiries with telephone number,
c) Description of the fault, which also reveals during which procedures the fault occurred, if
possible
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 33
14 Warranty
This Biometra instrument has been carefully build, inspected and quality controlled before
dispatch. Hereby Biometra warrants that this instrument conforms to the specifications given in
this manual. This warranty covers defects in materials or workmanship as described under the
following conditions:
This warranty is valid for 24 month from date of shipment to the customer from Biometra or an
authorized distributor. This warranty will not be extended to a third party without a written
agreement of Biometra.
This warranty covers only the instrument and all original accessories delivered with the
instrument. This warranty is valid only if the instrument is operated as described in the manual.
Biometra will repair or replace each part which is returned and found to be defective. This
warranty does not apply to wear from normal use, failure to follow operating instructions,
negligence or to parts altered or abused.
Manual T1 Thermocycler June 2009
34 _________________________________________________________________________
15 Equipment Decontamination Certificate
To enable us to comply with German law (i.e. §28 StrlSchV, §17 GefStoffV and §19 ChemG) and to avoid
exposure to hazardous materials during handling or repair, will you please complete this form, prior to the
equipment leaving your laboratory
COMPANY / INSTITUTE ____________________________________________________________
ADDRESS ____________________________________________________________
TEL NO _____________________ FAX NO _____________________ E-MAIL
_____________________ ______________________________
EQUIPMENT
If on loan / evaluation
Model
Serial No
__________
__________
__________
__________
__________
__________
__________
__________
Start Date: ________ Finish Date ________
Hazardous materials used with this equipment
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Has the equipment been cleaned and decontaminated? YES / NO (delete)
Method of cleaning / Decontamination
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
NAME ________________________________ POSITION __________________________
(HEAD OF DIV./ DEP./ INSTITUTE / COMPANY)
SIGNED ______________________________ DATE ______________________________
PLEASE RETURN THIS FORM TO BIOMETRA GmbH OR YOUR LOCAL BIOMETRA DISTRIBUTOR
TOGETHER WITH THE EQUIPMENT.
PLEASE ATTACH THIS CERTIFICATE OUTSIDE THE PACKAGING. INSTRUMENTS WITHOUT THIS
CERTIFICATE ATTACHED WILL BE RETURNED TO SENDER.
Manual T1 Thermocycler June 2009
___________________________________________________________________________ 35
16 EU - Konformitätserklärung / EU - Declaration of
Conformity
Göttingen, den 20. 08. 2004
im Sinne der EG-Richtlinie über elektrische Betriebsmittel zur Verwendung innerhalb bestimmter
Spannungsgrenzen 73/23/EWG
following the EC directive about electrical equipment for use within certain limits of voltage 73/23/EEC
und / and
im Sinne der EG-Richtlinie für die elektromagnetische Verträglichkeit 89/336/EWG.
following the EC directive about the electromagnetic compatibility 89/336/EEC ..
Hiermit erklären wir, daß folgende Thermocycler und Thermocycler Module:
Herewith we declare that the following thermocyclers and thermocycler moduls:
Typen:
types:
T1 Thermocycler 48, T1 Thermocycler 96, T1 Thermocycler Kombi,
T1 Thermocycler 384, T1 Thermocycler in situ,
T1 plus Thermocycler 48, T1 plus Thermocycler 96, T1 plus Thermocycler Kombi,
T1 plus Thermocycler 384, T1 plus Thermocycler in situ,
T1 Modul 48, T1 Modul 96, T1 Modul Kombi, T1 Modul 384, T1 Modul in situ
T1 Thermocycler 48, T1 Thermocycler 96, T1 Thermocycler Combi,
T1 Thermocycler 384, T1 Thermocycler in situ,
T1 plus Thermocycler 48, T1 plus Thermocycler 96, T1 plus Thermocycler Combi,
T1 plus Thermocycler 384, T1 plus Thermocycler in situ,
T1 module 48, T1 module 96, T1 module combi, T1 module 384, T1 module in situ
Best.-Nr. / Order No.: 050-900, 050-901, 050-902, 050-903, 050-904, 050-910, 050-911, 050-912,
050-913, 050-914, 050-920, 050-921, 050-922, 050-923, 050-924
den grundlegenden Anforderungen der
corresponds to the basic requirements of
EG-Niederspannungsrichtlinie 73/23/EWG und der
EC low voltage directive 73/23/EEC and the
EG-Richtlinie über die elektromagnetische Verträglichkeit 89/336/EWG entsprechen.
EC directive about the electromagnetic compatibility 89/336/EEC .
Folgende harmonisierte Normen wurden angewandt:
The following harmonized standards have been used:
Dr. Jürgen Otte
Quality Manager
Manual T1 Thermocycler June 2009
EN 55022:1998 + A1:2000 + A2:2003
EN 61000-3-3:1965 + A1:2001
EN 61010-2-010: 1994 + A1: 1996
Formular 006, Ver. 03
EN 55011:1998 + A1:1999 + A2:2000
EN 61000-3-2:2000
EN 61000-6-1:2001
EN 61010-1: 2001
36 _________________________________________________________________________
17 Subject Index
Beep......................................................... 27
Declaration of Conformity ........................ 35
Decontamination ...................................... 34
Heated Lid.......................................... 10, 14
Heating and cooling rates ........................ 22
Language ................................................. 28
Module
Exchange ............................................. 29
Program
Copy..................................................... 18
Create .................................................. 11
Delete................................................... 19
Increment ............................................. 21
Insert / Delete step ............................... 17
Loop......................................................15
Name ....................................................12
Pause....................................................25
Save......................................................16
Startt .....................................................23
Stop ......................................................25
Protocol
Print ......................................................27
Remaining run time...................................25
Safety precautions ......................................5
Self test.......................................................9
Technical specifications............................31
Trouble shooting .......................................30
Warranty ...................................................33
Manual T1 Thermocycler June 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement