advertisement
TVP-224HR
4-port VoIP Gateway with 4-port Broadband Router
Quick Installation Guide
Version 07.25.05
TRENDnet
TRENDware, USA
What's Next in Networking
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
Table of Contents
English ...................................................................................................... 1
1. Prepare for Installation ......................................................................
2. Install Hardware ................................................................................
3. Configure the computer's TCP/IP Settings ........................................
4. Configuration .....................................................................................
5. Connection through Telnet .................................................................
6. Connection through Console .............................................................
7. Dynamic DNS (Domain Name Server) ..............................................
8. Web Browser Dial Plan Sample .........................................................
3
4
1
2
9
10
12
14
English QIG
1. Prepare for Installation
Thank you for purchasing the TVP-224HR. This VoIP Gateway Router will allow you to share your broadband Internet connection with wired 10/100Mbps
Fast Ethernet computers as well as integrate your existing analog / PBX phone system for Internet telephone.
This guide will help you setup and configure your VoIP Gateway Router.
Following the installation instructions should be quick and easy. If you run into problems, please refer to the detailed installation procedures on the CD User's
Guide. If you need further technical support, please visit www.TRENDNET.com or call by phone.
Verify Package Contents
Please make sure you have everything in the box:
TVP-224HR
4-port VoIP Gateway with 4-port Broadband Router
Quick Installation Guide
Version 07.25.05
TRENDnet
TRENDware, USA
What's Next in Networking
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
Quick Installation Guide TVP-224HR CD-ROM
AC Power Adapter RJ45 Ethernet (LAN) Cable RS-232 Console Cable
Verify Equipment
Before installing the VoIP Gateway Router you should have:
1.
A working DSL Internet connection with Static IP or Dynamic IP with
DDNS.
2.
Cable / DSL Modem
3.
A computer with wired network card installed.
4.
TCP/IP protocol installed on each wired computer.
5.
A Web Browser such as Internet Explorer (5.0 or higher) or Netscape
Navigator (4.7 or higher).
1
English
2. Install Hardware
1.
Connect a RJ-45 network cable from Cable/ADSL Modem to TVP-224HR's
WAN port.
2.
Connect a RJ-45 network cable from one of the TVP-224HR's LAN ports to
PC.
3.
Connect Analog Phones/ Fax machine using RJ11 to FXS port(s).
WARNING:
Never connect a Trunk Line / PSTN line to a FXS Port. This will result In permanent damage to the FXS port.
4.
Connect FXO port(s) using RJ 11 Cable to PBX system or PSTN line.
5.
Power on your TVP-224HR.
TVP-224HR
2 1
4
3
5
Verify Hardware Installation
Make sure the following Router LEDs are on: Power, System (blinking), WAN,
LAN (100Mb/s or 10Mb/s Off)
SYSTEM LAN LINE
POWER
WAN
2
English
3. Configure the computer's TCP/IP Settings
To verify that your computer can communicate with your VoIP Gateway Router, you need to configure the TCP/IP settings in your PC Operating System (OS).
Set up the PC to “Obtain an IP address automatically”. Detailed setup procedures for Windows OS computers can be found in the User Manual on the CD provided. If you are running any other OS please see your system documentation for configuration information.
3
English
4. Configuration
The TVP-224HR comes with default LAN IP addresses “192.168.0.1”. The
TVP-224HR DHCP server is always enabled, and by default assigns 30 IP addresses starting from 192.168.0.10. You may use any PC to connect to the
LAN port of TVP-224HR, and then follow the steps below:
1.
Start your WEB browser. In the address field, Type in the following address
http://192.168.0.1.
2.
The pop-up screen should appear and prompt for user name and password.
The default values are:
User name:
admin
(all lower case)
Password:
123
3.
The following TVP-224HR VoIP Gateway Router Graphical User Interface main page should appear. If connection fails, check all cable connections between the Cable / ADSL Modem and TVP-224HR.
4
English
Internet Access
The following set-up information is designed to help you set-up your gateway to connect to the Internet. The set-up is different depending upon the type of
Internet Connection you have with your ISP (Fixed IP, PPPoE or DHCP). If you're not sure what type of connection you have, please contact your Internet
Service Provider and collect the required information. Below is a table that outlines the basic data you will require from your ISP.
Connection Type
Fixed IP (Static)
PPPoE
DHCP
Data required
Fixed IP Address, Subnet Mask, Default
Gateway and Primary DNS (Secondary
DNS is optional).
Login name and password (Service Name is optional)
Usually, none. But some ISP may require a particular Hostname, Domain name, or MAC
(physical) address.
After setting up Internet Access you will be able to Remote Manage the
Gateway using the WAN IP. By default the Web Access and Telnet
Access management are enabled. Both of these methods provide access over the internet so they do pose a potential security risk. It is recommended that once configuration is complete, both Web and Telnet access are disabled for security reasons. Turning of Web Access disables access from the Internet; however, you will still have web browser access from the LAN side from a computer in the same segment. If you prefer leaving Web and / or Telnet access enabled, be sure to change the administration password. In the event that you should forget the password see section 6 Connection through Console.
5
English
Static or Fixed IP Cable Connection
1.
From the Navigation Bar on the left side of the screen, Click on the
Internet
Access
Option. From the Internet Access sub-menu, Select
Fixed IP
.
The Fixed IP Configuration page will appear.
2.
Enter all field information as provided by your ISP and Click
Save
.
3.
Reboot
the TVP-224HR system in order for the changes to take effect.
4.
Launch
your web browser, (Internet Explorer or Netscape Navigator)
Type
http://www.trendnet.com in the address bar, and hit the Enter key. If the website appears, your router is configured correctly.
NOTE:
If the website does not appear, please verify that the information is entered correctly. Also call your ISP and verify your connection type. If you still can not establish Internet Access, please reference the trouble shooting section of your user manual.
6
English
PPPoE DSL Connection
1.
Click on the
Internet Access
option on the left-hand side of the screen and
Select
PPPoE
. The WAN PPPoE configuration page will appear.
2.
Enter PPPoE User Name and Password as provided by your ISP
.
3.
Click
Save
.
4.
Reboot
the TVP-224HR system in order for the changes to take effect.
5.
Launch
your web browser, (Internet Explorer or Netscape Navigator)
Type
http://www.trendnet.com in the address bar, and hit the Enter key. If the website appears, your router is configured correctly.
NOTE:
If the website does not appear, please verify that the information is entered correctly. Also call your ISP and verify your connection type. If you still can not establish Internet Access, please reference the trouble shooting section of your user manual.
6.
Setup DDNS Client (See section 7 on DDNS Client).
7
English
DHCP Connection
1.
Click on the
Internet Access
option on the left-hand side of the screen and
Select
DHCP
. The WAN PPPoE configuration page will appear.
2.
Enable
DHCP
, and enter Hostname, Domain Name and / or WAN MAC
Address (To find the WAN MAC Address, please navigate to Home / System
Status page) if required by your ISP.
3.
Click
Save.
4. Reboot
the TVP-221H system in order for the changes to take effect.
5.
Launch your web Browser, (Internet Explorer or Netscape Navigator) Type http://www.trendnet.com in the address bar, and hit the
Enter
key. If the website appears, your router is configured correctly.
6.
Setup DDNS Client (See section 7 on DDNS Client).
NOTE:
This quick guide covers only the most common situations.
Please refer to the User Guide (CD) for more information. For console / telnet configuration, please reference the Advanced User Guide (CD) for more detailed information.
8
English
5. Connection through Telnet
To use Telnet, Internet Access must have been previously setup so that the gateway is visible on the internet (See User Guide for More Information).
Alternatively, you can use Telnet to locally access the TVP-224HR, if you are under a router or switch and the TVP-224HR and your computer are in the same network segment.
To access the TVP-224HR Gateway from a remote location using Telnet, perform the following tasks:
Task
Open the windows command prompt and enter the telnet command followed by the IP address of the TVP-224HR
Gateway you want to access.
When the TVP-224HR Gateway prompts you to
Login
, enter the user name "admin”
When the TVP-224HR Gateway prompts you for
Password
, enter the password. “Console>” will appear. The default password is "123" but it is recommended that the password be changed for security considerations. The password can be changed from the Web Browser Administration / Password submenu page.
Type in “ping xxx.xxx.xxx”, where xxx.xxx.xxx is your ISP provided DNS Server IP or any known Public Internet Address.
The following dialogue confirms Internet Access
Console>ping 168.95.1.1
ping <168.95.1.1>: 56 data bytes
168.95.1.1 is alive
If the ping times out, you do not have Internet Access or the
Public IP Address you pinged is incorrect. Try another IP
Address. If you confirm that you do not have Internet Access, please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP-224HR.
Prompt
None
Login:
Password:
Console>
Type telnet xxx.xxx.xxx
admin
123 ping xxx.xxx.xxx
9
English
6. Connection through Console
The console port uses a DB-9 RS-232 connector. The supplied straight through
RS-232 cable connects the console port of the TVP-224HR to a console PC or terminal.
Task Prompt Type
Connect RS-232 Cable to TVP-224HR RS-232 console port a
your computer that you will use as a configuring terminal
Open HyperTerminal and enter the following Input Parameters when prompted:
When HyperTerminal Screen appears type “123”
Baud rate
Number of data bit
Parity check
Number of stop bit
Flow control
19,200
8
None
1
None
123
In the event that you forget your administration password, you can gain console access to the TVP-224HR using the super password. The super password is the last six digits of your MAC address located on the bottom of your TVP (00-50-2d-xx-xx-xx).
At the Console prompt enter the super password without hyphens. The password is all lower case. After gaining access, at the console prompt type in
net set manager password
<new_password> <new_password>
net store
net reset
If entry of new password is successful, the console will list “OK”.
You will now be able to gain Web Access from a PC in the same
local segment using the TVP-224HR LAN IP Address. If Web and / or Telnet Access are enabled, you will also be able to remote access the TVP-224HR by entering http:// followed by the TVP-224HR WAN IP or domain name.
10
English
Task
At the prompt
Console>
Enter
ping 168.95.1.1
The following dialogue indicates that Internet Access is successful.
ping 168.95.1.1
1 out of 1 pings succeeded.
Console>
If the ping times out, you do not have Internet Access. Please refer to the trouble shooting section of the User Manual or consult your ISP to make sure your Internet Access Data is correct and accurately entered into the TVP-224HR.
The following commands enable / disable web and telnet access respectively.
Net set http <on/off>
Net set telnet <on/off>
To reset to Factory Default settings, please perform the following commands to:
Erase all 'port', 'codec' & 'h323' configuration
config erase
Then access dial plan edit mode by entering
atpm req
Purge the dial plan from the database
atpm purge all
Store the changes
atpm store
Reset the network configuration to default
net set fac_default
net store
net reset
Key in
"yes"
to re-boot.
Prompt
Console>
Console>
Type
ping
168.95.1.1
on / off
11
English
7. Dynamic DNS (Domain Name Server)
This free service is a very useful feature. It allows Internet users to connect to the TVP-224HR using a URL, rather than an IP Address. This also solves the problem of having a dynamic IP address. With a dynamic IP address, your IP address may change whenever you connect to the Internet, making it difficult for others to find / connect to the TVP-224HR. With Internet DDNS, your IP may change but your Domain Name is Static.
The Service works as follows:
1.
You must register for the service at www.dyndns.org using the dyndns.org domain. This is the only Dynamic DNS service currently supported.
2.
After registration, follow the Service Provider's procedure to request a
Domain Name, and have it allocated to you.
Select Internet on the main menu, then DDNS submenu, to see a screen like the following:
12
English
3.
Enable Dyn-DNS. Please be sure to enter the data correctly. For instance, if you registered johnsmith.dyndns.org, please make sure that “dyndns.org” is in the Server Name Field and “johnsmith” is in the Host Name Field. Please also to enter “User Name” and “Password”.
4.
Click
Save.
5.
The TVP-224HR will then automatically ensure that your current IP Address is recorded and updated at the DDNS server. If the DDNS Service provides software to perform this "IP address update"; you should disable the
“Update" function, or not use the software at all.
6.
From the Internet, users will be able to connect to your 224HR using your
Domain name, shown on this screen.
13
English
8. Web Browser Dial Plan Sample
This section describes how to use a web browser to build a dial plan in the
VoIP Gateway. We suggest the following when developing your dial plan:
Draw an application diagram to illustrate / clarify application including:
1.
Local gateway: IP setup
2.
Local gateway: local telephone number setup
3.
Local gateway: remote gateway IP & remote telephone number setup
NOTE:
The Diagram below of Gateway A & B could be any combination of either the TVP-224HR (connected to switch by WAN port) or the TVP-221H (Connected by LAN port). The switch that joins these two gateways serves the purpose of initial lab configuration.
Under this configuration, both TVP Gateways (To be also referred to as
Gateway and GW) must be in the same IP segment. Once the dial plans have been entered and tested, the switch would be replaced by the public internet and the gateways would then have to be updated with the field application Internet Access Settings (eg. Public IP Address,
Subnet Mask and Gateway IP Address). In addition, all remote destinations in the dial plan must be updated with the actual application
/ field IP Addresses.
14
English
NOTE:
This diagram serves the purpose of illustrating the possible analog phone / PBX / PSTN integration / applications of the Gateway.
However, disconnect cadence provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway. This will require the assistance of your PBX supplier and /or Systems Integrator. Please also see User's Guide for additional information.
Scenario description: Two gateways connected by a switch
There are two gateways connected by a switch. They are generically labeled
“Gateway” but could be any combination of either the TVP-224HR (connected to switch by WAN port) or TVP-224HR (Connected by LAN port). Theoretically,
GW A is in Taiwan (Local Area Code have 2 digits) and GW B is in the US
(Local Area Codes have 3 digits).
Gateway A, 4 ports, is configured as follows:
1.
Gateway A IP: 192.168.1.20, mask IP: 255.255.255.0, gateway IP 0.0.0.0
(virtual IP)
2.
FXS Port 2 has a telephone set connected, its phone number is “203”
3.
FXS Port 3 has a telephone set connected, its phone number is “204”
4.
FXO Port 0 is connected to PBX. There are two telephone sets connected to the PBX. Their extension numbers are “800” and “801”.
5.
FXO Port 0 is registered as number “9” and it is connected to PBX
6.
PBX has an external line to PSTN. Dialing “9” connects you PBX, where “9” is dialed to connect to PSTN.
7.
The PSTN number to reach the PBX is “8888-2222”.
8.
Telephone A's number is “7777-1234” and belongs to the local PSTN
15
English
Gateway B, 4 ports, is configured as follows:
1.
Gateway B IP: 192.168.1.55, mask IP: 255.255.255.0, gateway IP 0.0.0.0
(virtual IP)
2.
FXS Port 2 has an analog telephone set connected, its phone number is
“203”
3.
FXS Port 3 has an analog telephone set connected, its phone number is
“204”
4.
FXO Port 0 is registered as number “9”. Dialing “9” connects you to the outside line.
5.
FXO Port 0 is connected to PSTN line “9999-3333”.
6.
Telephone B's number is “6666-4321” and belongs to the local PSTN.
Gateway A - IP setup:
1.
Navigate to Internet Access / Fixed IP Menu
2.
Type in IP Address: 192.168.1.20, Subnet Mask: 255.255.255.0 and Default
IP Gateway Address: 0.0.0.0 in the related fields.
3.
Click on
“Save”.
4.
Click on
“Reboot”.
Gateway B IP Setup:
5.
Navigate to Internet Access / Fixed IP Menu.
6.
Type in IP Address: 192.168.1.55, Subnet Mask: 255.255.255.0 and Default
IP Gateway Address: 0.0.0.0 in the related fields.
7.
Click on
“Save”.
8.
Click on
“Reboot”.
Gateway A: Dial Plan Setup
FXS Ports to Analog Phones - Gateway A has two phones on the FXS ports.
Telephone number 203 on Port 2 and 204 on Port 3. These numbers are part of the default dial plan and do not have to be entered. We can skip the local
Dial Plan setup including Telephone Address, hunt group and destination for phones 203 and 204.
16
English
How to Enter the Dial Plan
The Dial plan consists of three tables that include the Telephone Table, Hunt
Group (eg. Customer Service may have multiple phones that the GW must search through for an open line), and Destination Table (Both Local and
Remote). The dial plan has to be entered into all Gateways so that the local gateway knows how to process calls, sending them to its local ports or to remote gateways for further processing.
The following screen shots show an example for entering a dial plan for a single number. This example should give you the necessary insight as to how to enter the rest of the Dial Plan. If you still have difficulty understanding the dial plan and entering data, please reference the User Manual for more examples.
Telephone Number Table
1.
From the Navigation Menu on the left side, Select
Dial Plan Table Setup.
2.
From the window, please Select
<Add> <Telephone>.
3.
The following window will appear. Please Enter Data as shown.
4.
Click on
OK
.
17
English
Hunt Group Table
1.
From the Navigation Menu on the left side, Select
Dial Plan Table Setup.
2.
From the window, please Select
<Add> <HuntGroup>.
3.
The following window will appear. Please Enter Data as shown.
4.
Click on
OK
.
Local Destination ID Table
1.
From the Navigation Menu on the left side, Select
Dial Plan Table Setup.
2.
From the window, please Select
<Add> <Local_Destination_Channel>.
3.
The following window will appear. Please Enter Data as shown.
4.
Click on
OK
.
18
English
Store Dial Plan
1.
Continue entering the Gateway A Dial Plan as laid out in the tables below
(Telephone Table, Hunt Group Table and Destination Table) following the above procedures.
2.
After you have entered the Dial Plan, make sure you
Store Dial Plan
to flash memory. From the Navigation Bar on the left side, Click on
Store Dial Plan.
3.
The following screen will appear on the right side. Click on
YES.
Gateway B: Dial Plan Setup
1.
Enter Gateway B Dial Plan into Gateway B as shown in the tables below
(Telephone Table, Hunt Group Table and Destination Table) following the above procedures.
2.
After entering all the information listed in the tables below,
DO NOT
navigate away from Dial Plan Settings. Click
Store Dial Plan
, and click YES to save your dial plan to Flash Memory.
19
English
Gateway A and Gateway B dial plan setting
Gateway A Table Number Table
Phone #
Hunt
Group ID
Min.
Digits
Max.
Digits
Prefix strip
Prefix
Address
203
204
800
801
9
01
2
3
4
5
6
7
3
3
3
3
1
10
3
3
3
3
1
12
3
3
0
0
0
2
Function Comment
None
Dialing “203” calls phone on FXS Port 2
None
None
None
Dialing “204” calls phone on FXS Port 3
Dialing “800” calls PBX on
FXO Port 0, which then dials “800”.
This is an example only.
Please substitute your ext# on PBX if applicable
Dialing “801” calls PBX on
FXO Port 0, which then dials “801”.
This is an example only.
Please substitute your ext# on PBX if applicable
None
“9”
Dialing “9” from local phone on FXS Port connects you
FXO Port 0 PBX, where “9” is dialed for outside line.
After receiving “01” + 8 to
10 digits (2 Digit Taiwan
Area Code) from GW B,
“01” is stripped, prefix address “9” is dialed to PBX on FXO Port 0 for outside line and then, remaining 8 to
10 digits are dialed.
For PBX on FXO use only
For PBX on FXO use only
22
02
22
22
5
10
5
13
2
0
None
“22” is stripped and remaining 3 digits are sent to GW B.
Remote Zone # used to make calls to remote
GW B FXS (Internal Ext)
None
“02” + 8 to 11 digits (3 Digit
US Area Code) are sent to
GW B.
Remote Zone # used to make calls to remote
GW B FXO
(Externa -PBX / PSTN)
20
English
Gateway A - Hunt Group Table
Hunt Group ID
2
3
Hunt Type
2
2
# of Dest ID(s)
1
1
4
5
6
7
22
2
2
2
2
2
1
1
1
1
1
Dest. ID(s)
2
3
4
4
4
4
22
Gateway A - Destination Table
Dest ID
Mode
2
3
Local
Local
4
22
Local
Remote
Destination
Port = 2
Port = 3
Port = 0
Dest = 192.168.1.55/1720 TCP
NOTE:
The above destination table has both local destinations and remote destinations. When the gateways are taken out of this initial testing environment, and implemented in the field, the internet access settings will have to be updated. In addition, the above remote destination IP will have to be updated to the field IP address.
21
English
Gateway B - Telephone Number Table
Phone #
Hunt
Group ID
Min.
Digits
Max.
Digits
Prefix strip
Prefix
Address
203
204
9
02
11
01
2
3
4
5
11
11
3
3
1
10
51
10
3
3
1
13
5
12
3
3
1
2
2
0
Function Comment
None
None
Dialing “203” calls phone on Port 2
Dialing “204” calls phone on Port 3
None
None
None
None
Dialing “9” from local phone on FXS Port gets you a dial tone on FXO Port 0 for outside line.
Assumes that Telephone line is attached to Port
0 / Line 1
“02” is stripped, and the remaining 8 to 11 digits (3
Digit US Area Code) are dialed out on Port 0 to
PSTN.
Assumes that Telephone line is attached to Port
0 / Line 1
“11” is stripped and remaining 3 digits are sent to GW A.
Remote Zone # used to make calls to remote
GW A FXS (Internal Ext)
“01” + 8 to 10 digits (2 Digit
Taiwan Area Code) are sent to GW B.
Remote Zone # used to make calls to remote
GW A FXO
(External- to PSTN)
22
English
Gateway B - Hunt Group Table
Hunt Group ID
Hunt Type
# of Dest ID(s)
2
3
2
2
1
1
4
5
11
2
2
2
1
1
1
Dest. ID(s)
2
3
4
4
11
Gateway B - Destination Table
Dest ID Mode
2 Local
3 Local
4
11
Local
H.323
Destination
Port = 2
Port = 3
Port = 0
Dest = 192.168.1.20/1720 TCP
NOTE:
The above destination table has both local destinations and remote destinations. When the gateways are taken out of this initial testing environment, and implemented in the field, the internet access settings will have to be updated. In addition, the above remote destination IP will have to be updated to the field IP address.
23
English
Case 1: Making a call between Gateway A and Gateway B
Gateway B phone 203 calls to Gateway A phone 203
Caller Operation at GW B Equipment Operation
Pick up phone 203 (204)
Dial 11203 (11204, 11800,
11801)
Ring back tone is heard
1. GW dial tone is heard.
2. GW B Line 3 LED “ON”
1. Du Du is heard.
2. VoIP call processing
1. GW A Line 3 LED “ON”
Receiver Operation at GW A
Phone 203 rings
Pick up phone 203
VoIP Conversation VoIP Conversation
The above process is the same for Gateway B phone 203 and 204 calls to
Gateway A phone 201, 800 and 801.
Case 2: Gateway Phone to PSTN Phone
Gateway B phone 203 calls to PSTN phone A number 77771234
Caller Operation at GW B Equipment Operation Receiver Operation at GW A
Pick up phone 203
Dial 01-7777-1234
Ring back tone is heard
Ring back tone is heard
1. GW dial tone is heard.
2. GW B Line 3 LED “ON”
1. Du Du is heard.
2. VoIP call processing
1. GW A Line 1 LED “ON”
2. GW A is connected to PSTN
1. PSTN call processing Phone 77771234 is ringing
Receiver on 77771234 picks up
VoIP Conversation VoIP Conversation
The above dialing process is the same for phones 203, 204 to any GW A local
PSTN phone number.
24
English
Case 3: PSTN Phone to Gateway Phone
Phone A number (03)77771234 calls to Gateway B phone 203
Caller Operation at Phone A Equipment Operation
Receiver Operation at GW B phone 301
Pick up phone A
1. PSTN dial tone is heard.
Dial 88882222
Dial 22203 (22204)
1. Call being processed.
2. PBX plays voice greeting
1. Du Du is heard.
2. VoIP call processing
Ring back tone is heard
1. GW A Line 2 LED “ON”
1. GW A Line 2 LED “ON”
Phone 203 is ringing
Receiver picks up phone 203
VoIP Conversation VoIP Conversation
The above dialing process is the same for any calls made from GW A local
PSTN to remote phone numbers 203 & 204.
NOTE:
Case Tables 1-3 show the possible analog phone / PBX / PSTN integration / applications of the Gateway. Disconnect cadence provided by your phone company for your PSTN line and disconnect cadence provided by your PBX may require additional matching with the gateway. This will require the assistance of your PBX supplier and/ or
Systems Integrator. Please also see User's Guide for additional information.
25
English
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
26
English
TRENDnet
TRENDware, USA
What's Next in Networking
TRENDnet Technical Support
US/Canada Support Center European Support Center
Contact
Telephone:
Fax:
Email:
1(310) 626-6252
1(310) 626-6267 [email protected]
Tech Support Hours
7:30am - 6:00pm Pacific Standard Time
Monday - Friday
Contact
Telephone
Deutsch
:
+49 (0) 6331 / 268-460
Français
:
+49 (0) 6331 / 268-461
Español
:
+49 (0) 6331 / 268-462
English
:
+49 (0) 6331 / 268-463
Italiano
:
+49 (0) 6331 / 268-464
Dutch
:
+49 (0) 6331 / 268-465
Fax
: +49 (0) 6331 / 268-466
Tech Support Hours
8:00am - 6:00pm Middle European Time
Monday - Friday
TRENDware International, Inc.
3135 Kashiwa Street
.
Torrance, CA 90505
http://www.TRENDNET.com
Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement