Nexxa 16 Manual
USER MANUAL
16 CHANNEL
NETWORK VIDEO RECORDER
INSTRUCTION MANUAL
To obtain the best performance and ensure device function correctly, please read this instruction manual carefully and
completely.
FCC Compliance
USER-INSTALLER CAUTION: YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT
COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES.
NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A
CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE
EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,
AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT
HIS OWN EXPENSE.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
WARNINGS, CAUTIONS & COPYRIGHT
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of insinuated "dangerous voltage" within the products enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral rhombus is intended to alert the user to the presence of
important operating and maintenance (servicing) instruction in the literature accompanying the
product.
USERS OF THE SYSTEM ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL,
STATE, AND LOCAL LAWS AND STATUTES COIPCERNING THE MONITORING AND RECORDING OF
VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS
SYSTEM IN VIOLATION OF CURRENT LAWS AND STATUTES.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR RESPECTIVE
COMPANIES.
2
TABLE OF CONTENTS
1
2
3
4
5
6
INTRODUCTION ...................................................................................................................... 4
1.1
FEATURE....................................................................................................................... 4
1.2
SPECIFICATION .......................................................................................................... 4
HARDWARE OVERVIEW ...................................................................................................... 8
2.1
FRONT PANEL ............................................................................................................. 8
2.2
BACK PANEL................................................................................................................ 9
2.3
CAMERA & MONITOR LOOPING ......................................................................... 10
2.4
EXTERAL ALARM ..................................................................................................... 10
2.5
IR REMOTE CONTROL ........................................................................................... 12
2.6
PTZ (PAN, TILT AND ZOOM) CAMERA ............................................................... 13
SYSTEM SETUP ..................................................................................................................... 14
3.1
MENU SETUP INTERFACE(GUI) ........................................................................... 14
3.2
LIVE VIEWING AND POP-UP MENU .................................................................... 16
3.3
CAMERA SETUP ........................................................................................................ 19
3.4
RECORD SETUP ........................................................................................................ 25
3.5
ALARM SETUP ........................................................................................................... 26
3.6
NETWORK SETUP .................................................................................................... 28
3.7
AUTHORITY SETUP ................................................................................................. 33
3.8
DISK MANAGEMENT ............................................................................................... 35
3.9
SYSTEM SETUP ......................................................................................................... 36
HYBRID DVR PLAYBACK ................................................................................................... 41
4.1
TIME SEARCH ........................................................................................................... 43
4.2
EVENT SEARCH ........................................................................................................ 43
4.3
BACKUP ....................................................................................................................... 44
4.4
SYSTEM LOG ............................................................................................................. 45
BACKUP PLAYBACK ........................................................................................................... 46
5.1
MAIN SCREEN SETTING......................................................................................... 46
5.2
PLAYBACK OPERATION ........................................................................................ 49
NETWORK VIEWING & PLAYBACK ............................................................................... 52
6.1
IP ADDRESS SETUP ON PC SITE ........................................................................... 52
6.2
OPTIONAL MICROSOFT INTERNET EXPLORER SETUP.............................. 54
6.3
LOGIN .......................................................................................................................... 56
6.4
REMOTE CONTROL................................................................................................. 57
6.5
CONFIGURE ............................................................................................................... 62
APPENDIX A: RECORDING TIME LAPSE (HOURS) ............................................................. 72
APPENDIX B: HDD COMPATIBLE TABLE .............................................................................. 73
APPENDIX C: ERROR MESSAGE LIST .................................................................................... 75
3
1
INTRODUCTION
1.1 FEATURE
 H.264 hardware video compression
 Recording rate up to 120 FPS @ D1
 Support Mega Pixel IPcam for each channel.
 Real-time Display & Playback.

Support each channel backup

Support CMS (Central Management System)

Powerful mobile surveillance function, support Android phone & i-Phone
Audio:4 in & 1out/ Audio Backup / Audio Streaming






1.2
Individual recording setup & function for each channel
Support Privacy Mask
HDD damaged block detection & temperature alarm system (HDD S.M.A.R.T)
DVR log function (ex. user login/ logout) for device safety management
Up to four online clients for independent remote control; individual live-time,
play-back & time-search function available
SPECIFICATION
NEXXA16
MODEL
VIDEO
MODE
Multiplex
LIVE-TIME RESOLUTION
720 x 480 (NTSC)
720 × 576 (PAL)
LIVE-TIME DISPLAY RATE
16 × 30 Frame / Sec (NTSC)
16 × 25 Frame / Sec (PAL)
IPCAM RESOLUTION
Up to 1920 x 1080 (2 M-pixel)
IPCAM FRAME RATE
Up to 30 FPS @ NTSC per CH
SPLIT SCREEN
1, 4, 9, 16
VIDEO INPUT
BNC × 8
VIDEO OUTPUT (BNC)
BNC × 8
VIDEO OUTPUT (VGA)
Yes
VIDEO OUTPUT (HDMI)
Yes
AUDIO
AUDIO INPUT
RCA × 4
AUDIO OUTPUT
RCA × 1
4
AUDIO BACKUP
Yes
AUDIO STREAMING
Yes
RECORDING
COMPRESSION TYPE
H.264
RECORDING RESOLUTION ( D1)
720 x 480 (NTSC) / 720 x 576 (PAL)
RECORDING RESOLUTION ( Half
D1)
720 x 240 (NTSC) / 720 x 288 (PAL)
RECORDING RESOLUTION (CIF)
360 x 240 (NTSC) / 360 x 288 (PAL)
RECORDING RATE ( D1)
720 x 480 up to 120 PPS (NTSC)
720 x 576 up to 100 PPS (PAL)
RECORDING RATE ( Half D1)
720 x 240 up to 240 PPS (NTSC)
720 x 288 up to 200 PPS (PAL)
RECORDING RATE (CIF)
360 x 240 up to 240 PPS (NTSC)
360 x 288 up to 200 PPS (PAL)
IPCAM RECORDING RATE
Up to 30 FPS @ NTSC per CH
RECORDING MODE
Manual / Schedule / Alarm
PLAYBACK & SEARCH
PLAYBACK SPEED
Fast Forward
X 2 x4 X 8
Fast Backward
X 2 x4 X 8
Picture by Picture Playback
Pause
TIME SEARCH
Yes
EVENT SEARCH
Yes
EVENT LIST
10000 records per H.D.D (Maximum)
OSD & CONTROL INTERFACE
TITLE
8 Characters
ON SCREEN DISPLAY & SETUP
Time / Date / Setup Menu
GRAPHIC USER INTERFACE (GUI)
Yes
DVR CONTROL PANEL
Yes
MOUSE
Yes
IR REMOTE CONTROLLER
Yes
SUPPORT IE、FIREFOX & SAFARI
Yes
PLAYER
Yes
STORAGE & BACKUP DEVICE
INTERNAL HDD SUPPORT
SATA HDD x 4
EXTERNAL USB BACKUP DEVICE
(PAN DRIVE, HDD, BURNER)
Yes
6
X 16
X32
INTERNAL DVD BURNER BACKUP
No
NETWORK
ETHERNET
Yes (1G)
ETHERNET COMPRESSION FORMAT
H.264
IE REMOTE CONTROL
Yes
DDNS
Yes
E-MAIL & FTP
Yes
NETWORK IP
Static/ DHCP/ PPPoE/DDNS
MULTI-REMOTE CLIENT
Yes ( 4 Clients at the same time available)
ALARM
ALARM INPUT
16 In
ALARM OUTPUT
2 Out (NO/ NC)
MOTION DETECTION
Yes
MOTION DETECTION SENSITIVITY
1~10
VIDEO LOSS DETECTION
Yes
ALARM RECORDING
Yes
BUZZER
Yes
SETUP & OTHER FUNCTIONS
DST
Yes
EACH CHANNEL BACKUP
Yes
WATER MARK
Yes
PRIVACY MASK
Yes
PTZ CONTROL
Yes
RS-485
Yes
DIGITAL ZOOM
Yes
PASSWORD CONTROL
Two levels, one for system and the other for HDD format
KEY-LOCK
Yes
MULTI-LANGUAGE
Yes
FIRMWARE UPDATE
USB Host & Update on line
OTHERS
POWER INPUT
AC 100V~240V
DIMENSIONS (W x H x D)
430mm (W) × 88mm (H) × 382mm (D)
OPERATION TEMPERATURE
0 - 45 ℃
* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
7
2
HARDWARE OVERVIEW
2.1 FRONT PANEL
HYBRID DVR OPERATION
NO.
LABEL
OPERATION
IR Sensor For Remote Control.
1
Press The Button To Display No.1~No.16
2
1-16
CONTROL
Record, Playback And Control Button.
3
PANEL
10
8
11 12
1
2
USB Mouse Connector
43 4
22
FUNCTION
KEYS
5
23
Menu, ptz, hard disk status, Copy, Enter, Select, Zoom,
Auto keys.
Shuttle:
SHUTTLE
SHUTTLE
&
JOG
6
13
21 9
14
16
JOG
Fast Forward ×2 ×4 ×8
Fast Backward ×2 ×4 ×8
Jog: Picture By Picture Playback
15
17
24
18
19
8
PTZ
2.2
BACK PANEL
NO.
LABEL
OPERATION
1
POWER
Power switcher: AC100V~AC240V / 47-63Hz input.
2
VIDEO OUT
(HDMI)
HDMI connector
3
VIDEO OUT
(VGA)
VGA connector. Connect it to LCD monitor.
4
ETHERNET
RJ-45 connector for network.
5
ALARM
16 pin alarm input connector/ 2 pin GND connector/ 1 pin
alarm reset.
6
RS-232/ RS-485/
RELAY OUT
2 pin RS-232 connector, 1pin GND connector/ 2 pin RS-485/
2 pin Relay connector, 1 pin COM connector
7
AUDIO OUT
Audio output.
8
VIDEO OUT
(BNC)
Video output with BNC connector.
9
VIDEO IN
Video input with BNC connector.
10
AUDIO IN
Audio input x 4.
9
2.3
CAMERA & MONITOR LOOPING
Here recommend link cameras by sequence to avoid unexpected image broken, from CH1,
CH2, CH3, CH4…….
2.4
EXTERAL ALARM
There are three types of alarms that the system can be configured to handle. They are
Motion detection Alarm, External Alarm, Video Loss Alarm, and HDD Temperature
Warning.
A. Motion detection Alarm and External Alarm:
When motion detection or External Alarm was triggered, there are 4 possible actions
will be taken.
a. Monitor will display corresponding full screen alarm channel, it will switch
automatic mode to manual mode if buttons pressing activity occurred in 5 seconds.
b. Relays can be activated by motion detection or external alarm when turning on.
c. External alarm will be recorded in the event list. Motion detection can be set to yes
or no.
d. On the top right of the channel which the alarm triggered, the icons pop up to
remind the user.
stands for motion detection alarm.
stands for external
alarm.
B. Video Loss Alarm:
The default setting of Video Loss alarm is enabled and cannot be changed. Although
buzzer action can be disabled, an ALM record will still be added to the Event List that
indicates the precise time of video loss. On the top right of the channel which the alarm
triggered, the icon
pop up to remind the user.
C. HDD Temperature Warning
If the HDD temperature is over than the safe temperature (can be set up by user), the
buzzer start sounding to remind the user.
10
D. Alarm in connecter
Alarm 1~16 is the receiver of external alarm. D+ and D- is used for RS-485. TXD,
RXD, and GND is for RS-232. N.C, N.O, and COM is for relay output connection.
RS-485 D+
RS-485 sends +/ receives +
RS-485 D -
RS-485 sends -/ receives -
RS-232 TXD
RS-232 Transmit Data
RS-232 RXD
RS-232 Receive Data
GND
Ground
ALARM IN 1-16
Camera alarm input.
Alarm RST
Alarm Reset
N.C
Relay N.C.
N.O
Relay N.O.
COM
Common
EX1:Connect GND & Alarm to external IR detector.
EX2:Connect N.O & COM to external siren.
11
2.5
IR REMOTE CONTROL
ITEM
AUTO
SEL
Press AUTO to switch channel by channel
automatically.
Press this button to select the different assembled of
camera formats or perform PTZ functions. Moreover,
under the 16 split screen and full screen modes, press
this button for switching Audio ON/ OFF.
.REC
Press REC to start recording & again to stop.
1-16
Press the button to select the channel for full screen.
Fast backward
Picture by picture backward play
Picture by picture forward play
Fast forward
Play video forward
MODE
Split Screen Switch
ID
**ID setup to control DVRs
▲
Switch split screen & Move upward or increase.
►
Switch split screen & Move right or increase.
▼
Switch split screen & Move downward or decrease.
◄
Switch split screen & Move left or decrease.
To enter item or make choose.
MENU
To into or exit main menu
STOP
Stop play and playback
12
2.6
PTZ (PAN, TILT AND ZOOM) CAMERA
Following diagram for DVR connect between PTZ camera & joystick controller, for DVR to
control PTZ camera please make sure the CAMERA ID, BAUDRATE (default at 9600 bps)
and RS-485 cable.
(16CH Model)
Under “Two Core” connection, controller can control speed dome without integrated protocol
into DVR. Moreover, one keyboard can connect MAX 256 units of speed dome.
13
3
SYSTEM SETUP
3.1
A.
C.
MENU SETUP INTERFACE(GUI)
CAMERA SETUP
ALARM SETUP
14
B.
RECORD SETUP
D.
NETWORK SETUP
E.
AUTHORITY SETUP
G.
SYSTEM SETUP
F.
H.
15
DISK MANAGEMENT
EXIT
3.2
LIVE VIEWING AND POP-UP MENU
NOTE:The pop-up menu can be activated by moving the mouse cursor to the bottom
of the live viewing screen.
A.
GUI MENU BAR
With live viewing mode, press this button to get into the GUI menu.
B.
DISK INFORMATION
With live viewing mode, press this button to display disk information.
C.
DIGITAL ZOOM
In the live full screen mode, left-click the button of the mouse to pull a range to zoom
in or zoom out the image. User can right-click the button of the mouse to disable this
function. (NOTE: Using the mouse to operate digital zoom can zoom in to max. 16
times.) Moreover, user can also use ZOOM key on the front panel to perform this
function. (First, click ZOOM Key and then click ▲▼◄► key to select zoom in or
zoom out position. Finally, click ENTER key to complete the setting. Moreover, click
ZOOM Key again can disable digital zoom function. Using the panel key to perform
zoom in function is fixed at 2 times.)
16
D.
PTZ CONTROLLER
Within live-viewing mode, Clicks this button to get into the PTZ setup menu. User can
right-click the button of the mouse to exit PTZ Setup.
NOTE: Only for the camera supported PTZ function.
PTZ CONTROL
Press the minimization icon then the control panel becomes smaller:
Move the mouse and the arrow will follow the mouse and change direction. In this
mode user can click on the live view to control direction instead of the direction
key on control panel.
When a analog camera is connected, you can set up by clicking the tools icon:
17
E.
AUDIO VOLUME
Press this button, and the audio volume control board will pop up.
F.
DISPLAY CONTROL
Within live-viewing or playback mode, use display control to switch the camera
channel.
G.
RECORD AND PLAYBACK CONTROL
Same as front panel controller and remote controller.
H.
SOUND OUTPUT / PTZ CONTROL
There are little icon on the right top of the live vide of every channel. Click
to
enable the sound output. Click
to PTZ call out the control board. Note that if
those functions are not support by the camera linked, you will not see the
corresponding icons.
The sound options do not affect the audio recorded into playback video. As long as the
audio setup is enabled, the playback video includes audio even the sound output here
is turned off.
18
3.3
CAMERA SETUP
A. Camera Setup
Hybrid DVR can connect two various cameras, analog camera or IP-Cam.
Camera Type in Analog-CAM
Camera Type in IP-CAM
A-1. IPCam Quick Search
19
Press the “IPCam Quick Search” button and click “Search Device” button in the
following, HYBRID DVR will search the IPCAM devices which IP address are
setup as the same domain as HYBRID DVR IP address. Moreover, click the
IPCam device which from the list can import the device information to the
channel automatically without any manual key-in step.
1. Enable:Click the checkbox to decide performing the connection or not.
2. IP Address:Insert the IP address of the connecting device.
3. Port:Insert the port number of the connecting device.
4. User:Insert the user name of the connecting device.
5. Password:Insert the password of the connecting device.
6. State:After click the “connect IPCAM” button to test the IPCAM device, the
connection state will reveal among this column.
A-2. Connect IPCAM:After insert the IPCAM related information, click this button
to test the connection circumstances.
Note: To the camera connected via ONVIF protocol, the PTZ control function is
not supported.
B. Video Setup
Camera Type in Analog-CAM
20
Camera Type in IP-CAM
B-1. Resolution
Click drop down list to change the resolution of connecting device.
B-2. Quality
Click drop down list to change the image quality. (Currently, the maximum
quality of the 16CH HYBRID DVR is 24M/bps)
B-3. FrameRate
Click drop down list to change the frame rate of connecting device.
C. IPCam Image Setup
Camera Type in Analog-CAM
Camera Type in IP-CAM
C-1. Display
Use the mouse to enable or disable the camera display on the screen or not.
C-2. Title
Use the mouse to setup the title of connecting IP device.
C-3. Contrast
Press ◄ or ► to change contrast level. The adjustment value is between 0~255
C4. Brightness
Press ◄ or ► to change brightness level. The adjustment value is between
21
0~255
C-5. Hue
Press ◄ or ► to change hue level. The adjustment value is between 0~255
C-6. Saturation
Press ◄ or ► to change saturation level. The adjustment value is between
0~255
C-7. Sharpness
Press ◄ or ►/ mouse wheel to change sharpness level. The adjustment value is
between 0~15
C-8. Switch Dwell
Press ◄ or ► to change auto switch second. The value is between 0~99 sec.
D. Motion Setup
Camera Type in Analog-CAM
D-1. Relay Dwell
Press ◄ or ► to change the relay time or disable relay function.
D-2. Buzzer Dwell
Press ◄ or ► to change the buzzer time or disable buzzer function.
D-3. Enable Motion Detection
Click the checkbox to decide enable or disable motion detection.
D-4. Sensitivity
Press ◄ or ► to change sensitivity level.
D-5. Motion Area Setup
Press
to setup motion area.
Camera Type in IP-CAM
22
D-6. Relay Dwell
Press ◄ or ► to change the relay time or disable relay function.
D-7. Buzzer Dwell
Press ◄ or ► to change the buzzer time or disable buzzer function.
D-8. Area1 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area1. Click
“Motion Area Setup” and drag a blue area for motion detection.
D-9. Area2 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area2. Click
“Motion Area Setup” and drag a green area for motion detection.
D-10. Area3 Sensitivity
Press ◄ or ► to change the sensitivity of setup motion area in Area3. Click
“Motion Area Setup” and drag a red area for motion detection.
E. Privacy Setup
Camera Type in Analog-CAM
Camera Type in IP-CAM
E-1. Area1
Tick the “Area1” box and click “Area Setup” to drag a blue area for masking.
E-2. Area2
Tick the “Area1” box and click “Area Setup” to drag a green area for masking.
E-3. Area3
23
Tick the “Area1” box and click “Area Setup” to drag a red area for masking.
F. Audio Setup
The channel ticked means the sound from camera will be recorded into the playback
video. Vise versa. No sound will be recorded in the playback video of the channel
which is not ticked. It supports at most 4CH audio record.
24
3.4
RECORD SETUP
A. Post-Alarm Record Time
Press ◄ or ► to switch the recording time of post-alarm. The adjusting value is from
5~99 sec.
B. Mobile Streaming Setup
Press on to record the streaming for mobile viewing.
C. Record Mode
Use the drop down list to switch the recording mode. There are manual, schedule and
alarm trigger three varieties of mode.
Manual: Click
and
button on the right bottom of live viewing to start and
stop the manual record.
Schedule: Click the “Schedule Setup” button to set the schedule recording time.
Alarm trigger: When the alarm trigger is detected, it start recording as the alarm
setting.
25
3.5
ALARM SETUP
A. Alarm Trigger Setup
A-1. Alarm Auto Switch
Use the drop down list to switch the alarm auto switch. When the alarm is
triggered, the screen will switch to full screen, split screen (16CH split screen) or
disable.
A-2. Video Loss Detection
Use the drop down list to switch the video loss detection. When the video loss is
detected, the alarm will trigger.
A-3. Ext Alarm Detection
Use the drop down list to switch the Ext Alarm Detection. When the external
alarm is detected, the alarm will trigger.
A-4. Ext Alarm Mode
Choose normally open or normally close according to the external devise type.
A-5. HDD Temp. Warning
Use the drop down list to turn on or off the HDD Temp. Warning. When the HDD
temperature is too high, the alarm will trigger.
B. Alarm Output Setup
26
This control item separates into two parts, “Buzzer Time” and “Relay Time”. User can
press ◄ or ► to switch ext. alarm buzzer time and video loss buzzer time in “Buzzer
Time” option. The adjustment value is from 5 to 99 seconds. Moreover, among “Relay
Time” option, the user can press ◄ or ► to switch ext. alarm relay time and video loss
relay time. The adjustment value is from 5 to 99 seconds as well.
C. Alarm Event Setup
There are seven sort of events can be selected. When the selected items are happened
and triggered, the alarm will be activated.
27
3.6
NETWORK SETUP
A. IP ADDRESS SETUP
Press ◄ or ► to setup HYBRID DVR IP address.
A-1. IP Mode
Press drop down list to change IP mode to STATIC IP or DHCP.
A-2. IP Address
Use the virtual keypad to setup the HYBRID DVR IP ADDRESS.
A-3. Network
Use the virtual keypad to change SUBNET MASK.
A-4. Gateway
Use the virtual keypad to change Default GATEWAY.
A-5. DNS1
Use the virtual keypad to change DNS.
A-6. DNS2
Use the virtual keypad to change OTHER DNS.
A-7. WebPage Port
Use the virtual keypad to change the IE browser port.
B. PPPoE SETUP
28
B-1. PPPoE Setting
Press the drop down list to enable or disable PPPoE.
B-2. User Name
Insert the user name (ADSL account) which provided from local ISP.
B-3. Password
Insert the password which provided from local ISP.
B-4. Password Confirm
Insert the password again to confirm the password.
B-5. State
Present the current status of PPPoE function.
B-6. Send Mail After Dialed
Click the drop down list to enable or disable the function.
B-7. Subject
Insert the mail subject when dialed successfully.
C. DDNS SETUP
C-1. DDNS Enable
Click the checkbox to enable or disable DDNS function.
C-2. Provider
Click the drop down list to select DDNS provider.
C-3. Host Name
Insert the registered host name in the selected provider.
C-4. User Name
Insert the registered user name in the selected provider.
C-5. Password
Insert the registered password in the selected provider.
C-6. Update Interval
A period of time to update IP address.
C-7. State
The state after apply for DDNS.
Updating: Information update.
Idle: Stop service.
DDNS registered successfully, now log by
http://<username>.ddns.camddns.com: Registered successfully.
Updating Failed, the name is already registered.
Updating Failed, please check your internet connection.
29
D. MAIL SETUP
D-1. Enable
Use the checkbox to enable or disable the Mail Server function.
D-2. Mail Server
The IP address of Mail Server
D-3. SMTP Port
The port of SMTP (known as Simple Mail Transfer Protocol). (Default value is
25)
D-4. User Name
The user name while log in to the mail server.
D-5. Password
The password while log in to the mail server.
D-6. Sender’s Mail
The sender’s account when send the mail via this mail server.
D-7. Receiver’s Mail
The receiver’s mail address.
D-8. BCC Mail
The receiver’s mail address for Bcc Mail.
D-9. Subject
The subject while sending the mail.
E. FTP SETUP
E-1. Enable
Use the checkbox to enable or disable FTP Server.
E-2. FTP Server
The IP address of FTP Server.
E-3. User Name
The username while log in to the ftp server.
E-4. Password
The password while log in to the ftp server.
E-5. FTP Port
30
The port number of file transmission. (Default value is 21)
E-6. Path
The ftp path where the user wants to reserve the information.
F. DHCP Server Setup
F-1. Enable
Use the checkbox to enable or disable DHCP Server function. When the function
is activated, the HYBRID DVR can be treated as the DHCP server. The
HYBRID DVR will assign or distribute one of the IP address which is according
to the setup IP address range (start and end IP Address.) to the connecting
IPCAM (setup DHCP function as well).
F-2. Start IP Address
Use the virtual keypad to insert the start IP Address of DHCP server.
F-3. End IP Address
Use the virtual keypad to insert the end IP Address of DHCP server.
F-4. Lease Time
Press ◄ or ► to change the lease time of DHCP server.
G. UPNP Port Forwarding Setup
G-1. Enable
Use the checkbox to enable or disable UPNP port setup.
G-2. External HTTP Port
Use the virtual keypad to insert the external http port.
G-3. External RTSP Port
Use the virtual keypad to insert the external rtsp port.
31
H. Network Streaming Setup
For Network Viewing, the Hybrid DVR provides two compression formats.
H-1. Main Streaming
Users view the H.264 video playback via Internet browser. Selecting the option can
save the disk space while spend more time when loading the video.
H-2. Sub Streaming
Other than the original H.264 video, the Hybrid DVR saves a copy of M-JPEG video
used for Network Viewing. If it takes long time when loading the video on the web,
selecting sub streaming here may make it faster. However, to store both the H.264
and M-JPEG video, more disk space must be consumed.
32
3.7
AUTHORITY SETUP
A. HDD Format
Use the checkbox to enable or disable the authority of HDD Format function. If
enable this function, the user has to insert password while performing HDD format.
B. Anonymous User Login
Use the checkbox to enable or disable the authority of anonymous user login. If enable
this function, the user does not have to insert the username/ password and can view
the live image via IE browser.
C. Password Protection
Use the checkbox to enable or disable the authority of password protection.
D. Keyboard Lock
Use the checkbox to enable or disable the operation of control bar which is in the right
hand side of live view. The control bar can not work when keyboard lock is activated.
E. User Management
Among this item, user can setup the user management permission and the user
authority management.
E-1. Permission
Use the mouse to click the checkbox to modify and alter the user authority.
33
E-2. Add User
After click
button, the setup page will present in the following.
The user can distribute the authority and the permission for the new user.
34
3.8
DISK MANAGEMENT
A. Overwrite Mode
Click the drop down list to enable or disable overwrite function.
B. Hard Disk Full Warning
Click the drop down list to change value to 20/ 15/ 10 or 5% with non-overwrite mode.
When LEFT RATIO is below the setting, it will enable AUDIBLE ALARM (If
AUDIBLE ALARM of BUZZER of ALARM SETUP is ON).
C. Auto Deletion
Click the drop down list to enable or disable auto deletion function.
D. Reserve Day
Use ◄ or ► to setup the reserve day. While enable auto deletion function, the data
will be removed when reserve day is exceed the setting. The value can be setup
between 1~30 days
E. Storage Information
The information of storage device will present in this page.
F. Format HDD
Insert the user name and password while performing HDD format function.
35
3.9
SYSTEM SETUP
A. System Name
Use the virtual keypad to insert the name of the HYBRID DVR.
B. System ID
Use ◄ or ► to setup the HYBRID DVR ID. The adjustment value is between 0~32
C. Language
Use the drop down list to change the HYBRID DVR language. Currently, there are
English, Traditional Chinese and Simplified Chinese three options.
D. Date Format
Use the drop down list to change DATE. There are DD/MM/YYYY, YYYY/MM/DD
and MM/DD/YYYY three modes.
E. Version
The firmware version of the HYBRID DVR will show in this column.
F. Software Update
Click
button to perform firmware updating.
36
G. Configure Setup
Click the checkbox to select which item can be setup by the user. The user can also
load the setting to factory default, load the configure from USB and backup configure
to USB.
H. Time Setup
Click
button within “Time” block can adjust and synchronize the time of
the HYBRID DVR as the system time of the PC. Moreover, if the user clicks the
enable checkbox and
button within the NTP Setup block, the time of the
HYBRID DVR will synchronize as the NTP Server.
I. Day Light Saving Time
After enable the daylight saving time function, the user can use the drop down list to
select the start time and the end time of daylight saving time. After complete the
setting, please click
button to reserve the setting.
J. Status Display Setup
Use the mouse to click the options, which is including “Date and Time Display”,
“Record Information Display” and “Camera Title Display”.
37
K. Monitor Adjust
User can use ◄ or ► to adjust the monitor related setting within this page, there are
“Brightness”, “Contrast”, “Hue” and “Saturation” four options can be set. You can also
adjust Resolution here by selecting “1280*720”, 1024*768, or “1920*1080(HDMI) /
1280*1024(VGA).” The video output interface, HDMI or VGA, affects the resolution
options.
38
3.EX
DEBUG MESSAGE
The purpose of the following procedure is to export a HDD debug message file. If user has
problems with the DVR, the technical person can analysis the file and might find the cause
of problem.
 Plug in a USB disk.
 Enter the Authority Setup page and make sure the option “HDD Format (Require
Password Confirmation)” is ticked.

Enter the Disk Setup page. Click “Format HDD”.

Key in “@k” in the user name column to login. No password is required.

The screen turns to Advance Setup page. Click download. It takes about 10 seconds to
export the file.
39

When the downloading is complete, a message pops up to remind the user. Click”
OK”.

Now the debug message file should have been in your USB disk. Please send the file”
dbgms.tar” to your dealers technician.
40
4
HYBRID DVR PLAYBACK
Note: Under playback mode, it will output sound when switch to full screen mode.
A.
RECORD BACKUP
With playback mode, press this button to backup record (.da0 video backup) and press
this button again to finish backup. For performing the single image backup (.jpg single
image backup), press
first and then click this button to backup the necessary image.
B.
AUDIO VOLUME
Press this button, and the audio volume control board will pop up.
C.
DISPLAY CONTROL
Within playback mode, use display control to switch the camera channel.
D.
DIGITAL ZOOM
In the live full screen mode, left-click the button of the mouse to pull a range to zoom in
or zoom out the image. User can right-click the button of the mouse to disable this
function. (NOTE: Using the mouse to operate digital zoom can zoom in to max. 16 times.)
Moreover, user can also use ZOOM key on the front panel to perform this function. (First,
click ZOOM Key and then click ▲▼◄► key to select zoom in or zoom out position.
Finally, click ENTER key to complete the setting. Moreover, click ZOOM Key again can
disable digital zoom function. Using the panel key to perform zoom in function is fixed at
2 times.)
41
E.
RECORD AND PLAYBACK CONTROL
Same as front panel controller and remote controller.
42
4.1
TIME SEARCH
Select the start of playback time and then click
button to playback the
recorded data. If the time contains the recorded data, the time point within this page will
become red.
4.2
EVENT SEARCH
After entry to the event search page, user can click the event log item which shown on the
list to start playback. Moreover, the user could click
button to select the
specific event option to filter the event option that shown on the list.
43
4.3
BACKUP
After click the backup button, the user could use drop down list to select the storage
device, and the backup time selection mode, Time Mode/ Hours Mode. After that, click
button to start backup.
TIME MODE
Click ◄ or ► to select the start and end backup time.
Moreover, among “Select Channel” option, use the mouse to select the channel which is
going to backup.
44
4.4
SYSTEM LOG
System log is reserved all of the system record. The maximum storage quantity is 2000.
Click
button to perform the further data filter action. After complete
the specific item selection, please click
button to reserve the setting. While
return to the system log page, it will only reveal the specific selection items.
After click
button
45
5
BACKUP PLAYBACK
SYSTEM REQUIREMENT
CPU: Intel Celeron 1.6G
MEMORY: 256MB.
VGA: 32MB
VGA RESOLUTION: 1024 x 768.
OS: Windows XP / 2000 or above
SUGGESTED REQUIREMENT
CPU: Intel P4 2.8G
MEMORY:512MB or above
VGA:64MB or above
VGA RESOLUTION:1024 x 768
OS: Windows XP / 2000 or above
NETWORK BANDWIDTH: Upload Speed is 256kbps or above
5.1
MAIN SCREEN SETTING
The player
(A6Viewer.exe) is used to play the DVR backup video.
A6Viewer.exe can be attained from the attached CD or via the Internet; moreover,
while performing USB backup and DVD-RW backup, the software will be built
automatically as well.
A. MAIN SCREEN
Open the A6Viewer. Use Overlay mode can improve the system resource
performance.
Record and Playback Control
Select video source
Channel Selected
Save as AVI
Time & Event Search
1, 4, 9, 16 Channels Divide Screen
46
B. HDD PLAY
1. Remove the DVR HDD and connect it to the PC. The DVR HDD is Linux format,
so the Windows system may not know it. Please use the software “Ext2Fsd” to assign
a drive letter to the HDD. “Ext2Fsd” is in the attached CD or can be downloaded from
the Internet.
 Start the Ext2Fsd, and it will detects all the disks connected with your PC.
Right-click on the DVR HDD and choose “Change Drive Letter”.

Click “Add”

Assign a letter to the HDD, then click OK so that the HDD get the letter and can
be recognized by the Windows.
47
2. Under HDD play mode, select the DVR HDD to load the video file in the HDD.
C. File Play
1. You can use A6Viewer to open a single video backup file. Under file play mode,
select "Open".
2. Choose the path that the .daX file is reserved and pick the file to playback.
48
3. Press the play icon to play the video or still picture.
5.2
PLAYBACK OPERATION
A. TIME SEARCH
Select the Date and Time and then click
to play the film.
B. EVENT SEARCH
It will display all the events which are reserved within the DVR HDD after
press
trigger event.
(Shown in the following) and double click left button of mouse to
49
C. LOG
Click
and select a log file to read it.
D. ZOOM
Tick the “Zoom” box and drag an area on the screen. Click the area to zoom in.
50
E. BACKUP FILE TO AVI
1. Please select specific channel to backup.
2. During video playback mode please press AVI bottom
to start.
3. Make up a filename and path than press
bottom to start AVI backup.
4. Press AVI bottom
to finish backup.
51
6
NETWORK VIEWING & PLAYBACK
SYSTEM REQUIREMENT
CPU: Intel Celeron 1.6G
MEMORY: 256MB.
VGA: 32MB
VGA RESOLUTION: 1024 x 768.
OS: Windows XP / 2000
SUGGESTED REQUIREMENT
CPU: Intel P4 2.8G
MEMORY:512MB or above
VGA:64MB or above
VGA RESOLUTION:1024 x 768
OS: Windows XP / 2000
NETWORK BANDWIDTH: Upload Speed is 256kbps or above
6.1 IP ADDRESS SETUP ON PC SITE
Install cameras inside in LAN or use network cable to connect with PC. This is for
IPInstallerEng.exe to set up IP address of cameras. If OS is Windows XP SP2 or above,
the following Windows Security Alert will popup. Then, please click on Unblock.
Then, IPInstallerEng.exe will popup:
HYBRID DVR default IP address is 192.168.1.220
52
NOTE: Please input correct network parameters without blank spaces.
On Device Lists, it lists all servers. Click on one server and then its IP setting will show
on the right side. After editing the parameters and clicking on Submit, the following
dialogue box will popup. And, it will reboot the device with new parameters.
53
6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP
OPTION 1: DISABLE ACTIVEX WARNING
A. IE  Tools  Internet Options  Security  Custom Level  Security Settings 
Download unsigned ActiveX controls  Enable or Prompt (recommend).
B. IE  Tools  Internet Options  Security  Custom Level  Security Settings 
Initialize and script ActiveX controls not marked as safe  Enable or Prompt
(recommend).
1
2
3
4
5
Above three options are all based on select as the prompt.
As indicated in the dialogue box. Please select "YES."
54
OPTION 2: ADD TO TRUSTED SITES
IE  Tools  Internet Options  Security  Trusted sites  Sites
55
6.3 LOGIN
A. INSTALL ACTIVEX
B.
START INSTALL ACTIVEX
C.
ACCOUNT & PASSWORD LOGIN
After IP setup and connect to network or LAN, type IP address on IE Browser
directly. The following User name & Password Login window will popup.
Default user name: admin
Default password: admin
56
6.4 REMOTE CONTROL
LIVE VIEWING
DVR Configuration
PTZ Control
System Time
Play Back
REC
Screen Format
Time-Point Backup
A. HYBRID DVR Configuration
Get into HYBRID DVR network menu.
B. PTZ Control
PTZ control function panel
Direction Keys
PTZ Zoom in/out
Auto Pan Function
Preset Point
Setup
57
Up to 32 preset points
for operation
C. SYSTEM TIME
Live viewing mode: The current live viewing time.
D. SCREEN FORMAT
Switch screen format and click twice to switch different channels with full screen.
E.
REC.
Click to start record the live video to the PC or storage device. The saved file is
*.da16 file.
F.
Playback
Click and select time playback or event playback.
G.
Time-Point Backup
Click to select backup time point. The saved file is *.da0 file.
58
PLAYBACK by TIME SEARCH & EVENT SEARCH
Click
, and the playback window will popup
Playback Time
HDD Select
Time Search
Event Search
A. HDD Select
User can select HDD1 or HDD2 for playback
B. Playback Time
User can select the time then press “Time Search” for playback.
C. Time Search
User can select the time then press “Time Search” for playback.
D. Event Search
User can select event item by pressing “Event Search” for playback.
59
TIME-POINT BACKUP
Click
to operate Time-Point backup.
First, select Start and End backup time which have to among the Record Time.
Then, click Save button to select the position on PC where the user is going to backup the data.
After that, press OK button to start the backup.
Finally, double-click the left button of the mouse to open the saved backup file. The backup file
will named as the time when start to backup, such as, (20080526113258.da0) will be
2008/05/26 11:32:58.
60
OTHER FUNCTIONS
User can use other functions by clicking the left of mouse
A. Snapshot:
User can save any single picture from image.
B. Performance:
User can select image quality (high, medium & low).
C. Use Overlay:
User can use Overlay function. The function can save system resource and promote the
efficacy.
D. Play audio:
User can play audio function by channel.
Note: remote user can receive audio from HYBRID DVR. However, there’s no influence
on sound recording of playback video whether the audio is played or not.
61
6.5 CONFIGURE
A. System - System Information
A-1 SYSTEM INFORMATION
SERVER NAME: This name will show on the IP Installer.
MAC ADDRESS: The MAC address.(cannot be revised)
A-2 NTP Setting
TIME ZONE: It can only be modified via adjust “DATE” and “TIME SETUP
“in the DVR Menu).
NTP SERVER: Revise the time of DVR via different NTP Server.
B. SYSTEM – USER MANAGEMENT
User Management provides 3 levels of limits of authority: Administrator (the
highest), User, and Guest.
Administrator: Possessing the highest level of authority to operate full functions
within network.
User: Having Live Image and Video Playback authority. Moreover, PTZ controlled
is included as well.
Guest: Only have Live Image authority.
Default administrator account:
Username: admin
Password: admin
B-1 ANONYMOUS USER LOGIN:
YES: Accept anonymous user login without password as guest login.
62
NO: Anonymous login unacceptable.
B-2 USER MANAGEMENT:
Add: Key in the Username and Password. The manager can give authority to
the new user by tick at the choice below. (Ex. Ticking at “PTZ” allows
the new user to control the PTZ). You can apply the authority setting to
the channel you choose. The new user has no authority in those channel
that are not selected.
Modify: Click on selected User name on User List and the following window
will popup. After inputting Password and Confirm Password, click on
OK.
Remove: Click on selected User name on the user list and click on Remove.
C. SYSTEM / SYSTEM UPDATE
Firmware Upgrade:
Click on the “Browse” button to select the latest firmware and then press “Upgrade”
button to upgrade the firmware.
Load Default:
63
Click “Browse” to choose a file. You can load setup from your computer if you ever
clicked “Download” and saved the settings before.
ActiveX Updating:
The ActiveX control should be also updated when you update the DVR/NVR
firmware. Use the tool in the attached CD to uninstall the old ActiveX control so that
the newest version can be registered.
 Automatic Uninstall
Please follow the steps:
1. After updating the DVR/NVR firmware, close the web browser.
2. Run the file
"unreg" in the CD to automatically remove the
existing ActiveX component "WATCH_16R" from your PC.
3. Log in the DVR/NVR via web browser again, and the browser will require
you to install the new version of ActiveX control.
 Manual Uninstall
If the tool does not work, please follow the steps to uninstall ActiveX control
manually.
1. Look for the files
"KConfig.ocx" and
"WATCH_16R.ocx" in one of the possible paths:
"C:\WINDOWS\Downloaded Program Files"
"C:\WINDOWS\W16R"
"C:\WINDOWS\system32\WATCH_16R"
2. "Start" -> "Run" -> Key in: regsvr32(The path of KConfig.ocx) /u -> Click
"OK"
Ex.: regsvr32 C:\WINDOWS\system32\WATCH_16R\KConfig.ocx /u
3. "Start" -> "Run" -> Key in: regsvr32(The path of WATCH_16R.ocx) /u ->
Click "OK"
Ex.: regsvr32 C:\WINDOWS\system32\WATCH_16R\WATCH_16R.ocx /u
4. Log in the DVR/NVR via web browser again, and the browser will require
64
you to install the new version of ActiveX control.
D. NETWORK – IP SETTING
D-1
IP ASSIGNMENT
DHCP: In Dynamic Host Configuration Protocol (DHCP) mode, DHCP
server will get setting done automatically.
STATIC IP: Please input IP address, Subnet Mask, and Gateway based on
network environment.
D-2
UPNP PORT FORWARDING
When a router is used, you can enable this function to allow the user to link
the device in the intranet. The default HTTP Port is 80 and RTSP Port is 554.
65
E. NETWORK – PPPoE
E-1 PPPoE SETTING
Click on Enabled to enable ADSL dial function.
Username: Username for ADSL account.
Password: Password for ADSL account.
After dialed successfully, new IP address will appear.
E-2 SEND MAIL AFTER DIALED
Click on Enabled to enable SEND MAIL AFTER DIALED function.
E-3 SUBJECT
Mail subject.
F. NETWORK / DDNS SETTING
66
Click on Enabled to enable DDNS function.
F-1 DYNDNS.ORG
DDNS SETTING - DYNDNS.ORG
PROVIDER: Select dyndns.org
HOSTNAME: The registered hostname in DYNDNS.ORG.
USERNAME: The registered username in DYNDNS.ORG.
PASSWORD: The registered password in DYNDNS.ORG.
SCHEDULE UPDATE: A period of time to update IP address.
STATE
1. Updating: Information update.
2. Idle: Stop service.
3. DDNS registered successfully, now log by
http://<username>.ddns.camddns.com: Registered successfully.
4. Updating Failed, the name is already registered.
5. Updating Failed, please check your internet connection.
F-2 DDNS.CAMNNDS.COM
67
DDNS SETTING – DDNS.CAMDDNS.COM
PROVIDER: Select ddns.camddns.com
USERNAME: The registered username in DDNS.CAMDDNS.COM.
SCHEDULE UPDATE: A period of time to update IP address.
STATE
1. Updating: Information update.
2. Idle: Stop service.
3. DDNS registered successfully, now log by
http://<username>.ddns.camddns.com: Registered successfully.
4. Updating Failed, the name is already registered.
5. Updating Failed, please check your internet connection.
DDNS Setting Steps:
Press
1
○
“ENABLE” option to enable DDNS function and select
2
○
“ddns.camddns.com” of the provider drop down list which is suggested to use. In
the following, insert
3
○
the username which the user wants to apply
(i.e. HYBRID DVR_GODDNS in here). After that, click
4
○
“Apply” button to
apply a DDNS domain name.
1.
2.
3.
4.
Finally, the HYBRID DVR domain name○
5 (http://HYBRID
DVR_GODDNS.ddns.camddns.com) will be shown on the state block.
68
5.
NOTE: 1. If the user selects another provider which is ddns2.ydsHYBRID DVR.com, all of
the setting steps are the same with ddns.camddns.com setting.
2. However, if dyndns.org provider is selected, please go to www.dyndns.org website
to register the account first. The user has to fill in the username, password and
hostname for applying the account. After the user applied the account successfully,
the dyndns.org will give the user a complete DDNS domain name.
3. If setting up IP schedule update too frequently, the IP may be blocked. In general,
schedule update every day (1440 minutes) is recommended.
G.
NETWORK / Mail & FTP
Click on “Motion” or “Alarm” option to enable Mail Setting and FTP Setting
function.
Mail Server: The IP address of Mail Server
SMTP Port: The port of SMTP (known as Simple Mail Transfer Protocol). (Default
value is 25)
69
Username: The username while log in to the mail server.
Password: The password while log in to the mail server.
Sender’s Mail: The sender’s account when send the mail via this mail server.
Receiver’s Mail: The receiver’s mail address.
Bcc Mail: The receiver’s mail address for Bcc Mail.
Event Subject: The subject of this mail. (Default value is ALARM MAIL)
FTP Server: The IP address of FTP Server.
Username: The username while log in to the ftp server.
Password: The password while log in to the ftp server.
Port: The port number of file transmission. (Default value is 21)
Path: The ftp path where the user wants to reserve the information.
Finally, click on Apply button to reserve the setting.
H. NETWORK / DHCP
Assign the Start IP and End IP for DHCP. Key in lease time here to decide the
frequency that the IP address is renewed.
I.
OTHERS / Player Downloaded
Click “Player” button to start download A6Viewer.exe to local PC.
70
J.
OTHERS/ HYBRID DVR Setting
HYBRID DVR setting can be changed via the Internet.
71
APPENDIX A: RECORDING TIME LAPSE (HOURS)
2TB
IMAGE QUALITY
(Mbps)
16CH
UNIT:Hours
LOW(0.25M)
MEDIUM(0.5M)
STANDARD(1M)
HIGH(1.5M)
AVERAGE
AVERAGE
AVERAGE
AVERAGE
960
480
240
160
4TB
IMAGE QUALITY
(Mbps)
16CH
UNIT:Hours
LOW(0.25M)
MEDIUM (0.5M)
STANDARD (1M)
HIGH (1.5M)
AVERAGE
AVERAGE
AVERAGE
AVERAGE
1920
960
480
320
6TB
IMAGE QUALITY
(Mbps)
16CH
UNIT:Hours
LOW(0.25M)
MEDIUM (0.5M)
STANDARD (1M)
HIGH (1.5M)
AVERAGE
AVERAGE
AVERAGE
AVERAGE
2880
1440
720
480
UNIT:Hours
8TB
IMAGE QUALITY
(Mbps)
16CH
LOW(0.25M)
MEDIUM (0.5M)
STANDARD (1M)
HIGH (1.5M)
AVERAGE
AVERAGE
AVERAGE
AVERAGE
3840
1920
960
640
* The value is for reference only
72
APPENDIX B: HDD COMPATIBLE TABLE
Brand
SEAGATE
WD
Model
Capacity
others
ST380815AS
80 GB
7200 10
ST3160815AS
160 GB
7200 10
STM3250820AS
250 GB
7200 10
ST3250310SV
250GB
SV35.3
ST3400620AS
400 GB
7200 10
ST3500320SV
500GB
SV35.3
ST3500410SV
500GB
SV35.5
ST3500320AS
500GB
7200 11
ST3500418AS
500GB
7200 12
ST3500312CS
500GB
Pipeline HD .2
ST3750640AS
750 GB
7200 10
ST3750330AS
750 GB
7200 11
ST31000333AS
1TB
7200 11
ST31000340AS
1TB
7200 11
ST31000340NS
1TB
Barracuda ES.2
ST31000340SV
1TB
SV35.3
ST31000322CS
1TB
Pipeline HD .2
ST31000525SV
1TB
SV35.5
ST31000524AS
1TB SATA3
7200 12
ST1500DL003
1.5TB SATA3
Barracuda LP
ST31500341AS
1.5TB
7200 11
ST32000542AS
2TB
Barracuda LP
ST3320620AS
320 GB
7200
ST3500413AS
500GB
7200
ST3500320NS
500GB
7200
WD1600AAJS
160 GB
7200 CB
WD2500AAKS
250 GB
7200 CB
WD2500AVVS
250 GB
7200 GP
WD3200AVVS-73L2B0
320GB
7200 GP
WD5000AACS
500 GB
7200 GP
WD5000AVVS
500 GB
7200 GP
WD5000AAKS
500GB
7200 CB
500GB
7200 RE
WD5002ABYS
73
WD5000AAKX
500GB SATA3
Caviar Blue
WD5000AUDX
500GB SATA3
Green Power
WD6400AAKS
640 GB
7200 BLUE
WD6400AVVS
640 GB
7200 GP
WD7500AACS
750GB
7200 GP
WD7500AVVS
750GB
7200 GP
WD10EACS
1TB
7200 GP
WD10EADS
1TB
Caviar Green
WD10EVDS
1TB
Green Power
WD10EVVS
WD
HITACHI
1TB
7200 GP
WD10EARS
1TB
Caviar Green
WD10EALX
1TB SATA3
Caviar Blue
WD10EURX
1TB SATA3
Green Power
WD15EADS
1.5TB
7200 GP
WD15EARS
1.5TB
7200 GP
WD15EURS
1.5TB
7200 GP
WD5000AVDS-63U7B0
1.5TB
7200 GP
WD15EVDS
1.5TB
7200 GP
WD20EADS
2.0TB
7200 GP
WD20EVDS-63T3B0
2.0TB
7200 GP
WD20EARS
2.0TB
Caviar Green
WD20EURS
2.0TB
7200 GP
WD30EURS
3TB
CE-GP
WD30EZRX
3TB
7200
HDS721616PLA380
160 GB
7200
HDT725025VLA380
250 GB
7200
HDT725032VLA360
320 GB
7200
HDP725050GLA360
500 GB
7200
HCP725050GLA380
500GB
7200
HDT721010SLA360
1TB
7200
HDS721010CLA332
1TB
7200
HDS722020ALA330
2TB
7200
HDS721050CLA362
500GB
7200
74
APPENDIX C: ERROR MESSAGE LIST
ERROR MESSAGE
ERROR STATUS & REASON
NOTE
DISK ACCESS ERROR!
H.D.D. Data structure Un-normal.
Data does not record into HYBRID DVR or bad sector on
HYBRID DVR H.D.D. Please install another H.D.D. and
perform the record again.
UPDATE FILE ERROR!
Please re-download the update file and update again.
FIRMWARE UPGRADE
FAILED
Please reboot the HYBRID DVR and upgrade the firmware.
Please send the HYBRID DVR back to repair when
HYBRID DVR is disability.
MEDIA ACCESS FAIL!
The USB file format is incorrect (Please format the pen
drive to FAT32) or Pen Drive is setup to ONLY READ mode
(Please annul ONLY READ mode) when reserve the data by
using Pen Drive. The data cannot be burn into CD/DVD
disc. Please change another CD/DVD disc and backup the
file in CD/DVD disc storage.
NO FILE!
There is no upgrade file within Pen Drive or the name of
upgrade file does not correspond with HYBRID DVR
format. Please adjust the upgrade file name based on the
following information.
16CH -> UpdateR.bin
08CH -> Update8.bin
04CH -> Update4.bin
USB DEVICE NOT FOUND
NO USB
Pen Drive undetected. Please Unplug the Pen Drive and plug
it again.
BACKUP START TIME
Backup start time error.
ERROR
BACKUPEND TIME ERROR
Backup end time error.
DISK ERROR
The data cannot be burn into CD/DVD disc. Please change
another CD/DVD disc and backup the file.
FAN FAILED
Fan Error Warning.
NO LOG DATA
No Events Record.
SCHEDULE RECORD
The condition is caused by trying to stop recording when
perform the schedule record. Please setup the record to
manual mode and then stop the record.
PLEASE SELECT ONE
CAMERA
The message will be shown while using the ZOOM function
under split screen condition. Please switch the screen into
full screen mode and then operate the ZOOM function.
75
V1.2_120521
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement