Diamond Digital DV42P!mk2 User Manual

Diamond Digital DV42P!mk2 User Manual
ENGLISH
Plasma Display
USER'S MANUAL
Thank you for purchasing the Plasma Display.
Before using your Display, please read the "SAFETY INSTRUCTIONS"
and this "USER'S MANUAL" carefully to learn how to operate the
Display properly. Keep this manual in a safe place. You will find it
useful in the future.
Notes on lnstallation
This product is marketed with the assumption that it is to be
installed by qualified personnel with relevant skills and
competence. It is recommended to consult with an installation
specialist or your dealer install and set up the product. We cannot
assume liabilities for damages caused by improper installation or
mounting, misuse, modifications or natural disasters.
1
IMPORTANT SAFETY INSTRUCTIONS
SAFETY POINTS THAT YOU SHOULD KNOW ABOUT YOUR Plasma Display
Follow all warnings and instructions marked on this Plasma Display .
The lightning flash with arrowhead symbol, within an
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING:
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle, is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
z TO AVOID FIRE OR ELECTROCUTION, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE.
zTHE MONITOR SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS SUCH AS
VASES FILLED WITH LIQUIDS, SHOULD NOT BE PLACED ON THE DISPLAY.
z There are no user serviceable parts inside the DISPLAY.
z Model information and serial numbers are indicated on the
NOTE:
rear side of the DISPLAY.
CAUTION:
Adjust only those controls that are covered in these instructions, as improper changes or modifications not
expressly approved by us could void the user's authority to operate the DISPLAY.
MODIFICATIONS:
The FCC requires that the user be notified that any changes or modifications made to this device, that are not
expressly approved by us may void the user's authority to operate the equipment.
POWER SOURCE
THIS DISPLAY IS DESIGNED TO OPERATE ON 100-240 VOLT 50/60Hz, AC CURRENT. INSERT THE POWER CORD INTO A
120 VOLT 60Hz or 240 VOLT 50Hz OUTLET.
TO PREVENT ELECTRIC SHOCK, DO NOT USE THE DISPLAY (POLARIZED) PLUG WITH AN EXTENSION CORD,
RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED. THIS IS
TO PREVENT BLADE EXPOSURE. NEVER CONNECT THE DISPLAY TO DIRECT CURRENT OR ANYTHING OTHER THAN
THE SPECIFIED VOLTAGE.
CAUTION:
2
Never remove the back cover of the Plasma Display as this can expose you to very high voltages and
other hazards. If the Plasma Display does not operate properly, unplug the Plasma Display and call
your authorized dealer or service center.
ENGLISH
Our reputation has been built on the quality, performance, and ease of service of Plasma Display .
Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety
tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your
Plasma Display .
Read before operating the appliance
Follow all warnings and instructions marked on this Plasma Display .
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this appliance near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other appliances (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and at the point
where they exit from the appliance.
11.Only use the attachments/accessories specified by the
manufacturer.
12
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the appliance. When a cart is used, use caution
when moving the cart/appliance combination to
avoid injury from tip-over.
13.Unplug this appliance during lightning storms or when unused for
long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is
required when the appliance has been damaged in any way, such
as when a power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally, or
has been dropped.
15.To reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
16.Do not expose this appliance to dripping or splashing. Do not place
objects filled with liquids on this appliance.
Do not place any objects on top of the DISPLAY. They may
fall or cause a child to climb up to retrieve the objects.
17. The Shock Hazard Marking and Associated Graphical Symbol
is provided on the bottom panel of the unit.
18. This appliance is designed to comply with the recommended
safety standards for tilt and stability.
Do not pull the cabinet with excessive force. Doing so can
cause the product to overturn, resulting in damage to the
product and/or personal injury.
19. Follow instructions for wall, shelf, or ceiling mounting as
recommended by the manufacturer.
20. An outdoor antenna should not be located in the vicinity of
overhead power lines or other electrical circuits.
Disposal of this product may require specific instructions
pertaining to your resident state. For disposal or
recycling information, please contact your local
authorities or the Electronic Industries Alliance:
www.eiae.org.
CAUTION: PREVENTION OF SCREEN BURN IN
Continuous on-screen displays such as video games, stock market quotations, computer generated
graphics and other fixed (non-moving) patterns can cause permanent damage to the DISPLAY. Such
“SCREEN BURN IN” constitute misuse and are NOT COVERED by our Factory Warranty.
PUBLIC VIEWING OF COPYRIGHTED MATERIAL
Public viewing of programs broadcast by DISPLAY stations and cable companies, as well as programs from other sources, may
require prior authorization from the broadcaster or owner of the video program material.
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
Please read this User's Manual thoroughly, especially the Important
Safety Instructions on Pages 2 to 3 and 6 to 10. Misuse may cause
damage to your PLASMA DISPLAY and could shorten its lifespan, or
may even cause injury to yourself. Should you encounter any difficulty
in the set-up or operation of your DISPLAY, refer to the
Troubleshooting guide at the back of this manual.
In the unlikely event that there is a problem with your PLASMA
DISPLAY, switch off the power and unplug the DISPLAY, and contact
your dealer immediately.
CAUTION
Under no circumstances should you remove the back cover of your
PLASMA DISPLAY.
Never guess or take any chances with electrical equipment of any kind
- it is better to be safe than sorry!
Software Notice
It is prohibited for the end user of this product to copy, reverse
engineer or reverse compile the software included therein, to the
extent permitted by law.
Plasma Display
After the Plasma Display has been on for any length of time, you will
notice that the screen becomes warm. Please note that this is normal.
To prevent scratches or damages to the Plasma screen, do not knock
or rub the surface with sharp or hard objects. Clean the screen with a
soft cloth moistened with warm water and dry with a soft cloth. A mild
soap may be used if the screen is extremely dirty. Do not use harsh or
abrasive cleaners!
CAUTION
Use a soft cloth to clean the cabinet and the control panel of the
DISPLAY. When excessively soiled, dilute a neutral detergent in
water, wet and wring out the soft cloth, then wipe the DISPLAY and
afterwards wipe it off with a dry soft cloth.
4
Never use acid/alkaline detergent, alcoholic detergent, abrasive
cleaner, powder soap, Electronic equipment cleaner, car wax, glass
cleaner, etc. especially because they would cause discoloration,
scratches or cracks.
FEATURE
Enhanced definition plasma
panel
The 42-inch color plasma display panel, with a resolution of 852 (H) x
480 (V) pixels, creates a widescreen picture. This panel features a thin
form factor and can be hung on a wall with an optional wall mounting
kit.
Clear PictureTM Electronics
Advanced electronics eliminate noise, increase contrast and detailand
optimize color for a rich vibrant image.
Easy-to-use remote control and
on screen display system
The included remote control operates all DISPLAY functions. Further,
the on-screen display system, shows the status of the control settings
in an easy-to-view fashion.
Power saving system
The International ENERGY STAR® power saver feature saves power
consumption automatically when input signals are not available.
When connected to a VESA DPMS-compliant PC, the monitor cuts its
power consumption while it is idle.
ENGLISH
Important
IMPORTANT SAFETY INSTRUCTIONS…………....….2
FEATURE…………………………………………….………….4
COMPONENT NAMES………….………………………….15
Main Unit…………………………………………………………15
Remote Control…………………………………………….……16
Loading the Batteries……………………………………………16
Handing the Remote Control…………………………………..16
INSTALLATION INSTRUCTIONS…………………...….10
Installation……………………………………….………………..10
Anti-tumble measures…………………………….……..…..…..10
Mounting the Speaker Unit…………….……………………..11
Power Cord Connection………………….……………………..11
C o n n e c t i n g S i g n a l … … … … … … … … … . .. … . … …… . 1 2
Connecting to Video Imaging Device……………..….……….13
Connecting to a PC…………………………. ………...………..14
COMOPERATING INSTRUCTIONS….………….…....15
Main Uint……………….………………….…………………….. 15
Romote co ntro l……………… ….……………… … … . . 16
OPERATING INSTRUCTIONS….………….…....18
Turning Power On and Off…………….………………………..18
Input Switching.......………………….…………………………..19
Volume Adjustment……………….…………………………..19
Audio Mute………………………………………. ………….…..19
Using the Menu Screen (On-screen display system). ……….20
PICTURE PARAMETERS ………………………………. 22
PC PARAMETERS……………………………………..………..26
AUDIO SETTING……….……….……………..………..…….....27
PICTURE IN PICTURE (PIP)..……………………………..…...28
Selecting PIP size…..……………………………………………28
Selecting PIP Source……….…………………………………..28
PIP Combination Table…….………………………………….28
GENERAL SETTINGS………………….………….…………….31
Size Switching(ASPECT)....………….……….…………….……35
ZOOM..….……………………………………………….…………..36
DISPLAY..........………………………………………….….………36
STILL.……………………………………………………..….………36
SLEEP.……………………………………………………..….………36
SWAP…..……………………………………………….………..…36
OTHER FEATURES…………….………………………….…….36
Automatic Store………...…………………………………….………36
Signal Check (RGB Input)………………………………….………37
Power Save Mode (RGB Input)…………………………….….…..37
IMAGE RETENTION OF PLASMA DISPLAY…………..…38
NOTES………………………………..……….………………......38
TROUBLESHOOTING………….………….……………………39
Symptoms That Seemingly Appear to be Failures…………..…….39
Actions to Corrections Abnormal Displays………………………..41
PROUDCT SPECIFICATIONS………..……………………...42
Signal Input ……………………………………………...…………..43
Recommended Signal List………………………………………....44
SERVICE CONTACTS…………………..……………………...46
Notes about this manual
The information in this manual is subject to change without notice.
While meticulous care has been taken in the preparation of this manual, you are requested to notify your dealer or us should you have any comments,
views or questions about our product.
z Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the product.
We are
not held liable for damages caused by improper handling of the product.
z Reproduction of this manual in whole or in part without our prior written permission is prohibited.
z The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.
z
z
5
ENGLISH
CONTENTS
SAFETY INSTRUCTIONS
This Plasma display has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if
you are to obtain the best results and safety is to be assured.
Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.
About the Symbols
WARNING
CAUTION
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect
handling.
This symbol indicates information that, if ignored, could result possibly in personal injury or physical damage due to
incorrect handling.
Typical Symbols
This symbol indicates an additional warning (including cautions). An illustration is provided to clarify the contents.
This symbol indicates a prohibited action. The contents will be clearly indicated in an illustration or adjacent to the symbol (the symbol to the left
indicates that disassembly is prohibited).
This symbol indicates a compulsory action. The contents will be clearly indicated in an illustration or adjacent to the symbol. (The symbol to the
left indicates that the power plug should be disconnected from the power outlet).
WARNING
Never use the monitor if a problem should occur.
Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables,
penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and
then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never
attempt to make repairs yourself because this could be dangerous.
Disconnect the
plug from the
power outlet.
Do not insert liquids or foreign objects.
Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are
present.
If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power
outlet and contact your dealer.
• Do not place the monitor in a bathroom.
• Do not expose the monitor to rain or moisture.
• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor.
• Do not place metals, combustibles, etc on or around the monitor.
Never disassemble or modify the monitor.
The monitor contains high voltage components. Modification could result in fire or electrical shock.
• Never remove any fixed cover.
Do not give the monitor any shock or impact.
If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the
glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact
your dealer.
Do not place the monitor on an unstable surface.
If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock.
• Do not place the monitor on an unstable, slant or vibrant surface such as a wobbly or inclined stand.
Do not obstruct the ventilation of the monitor.
If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and
shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation.
• Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls.
• Do not place anything around ventilation openings of the monitor.
• Never block ventilation openings.
• Do not put the plasma screen side up.
• Do not cover the monitor with a tablecloth, etc.
• Do not place the monitor on a carpet or bedding, or near a curtain.
Use only the correct power outlet.
Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the
indication on the monitor and the safety standard.
• The enclosed power cord must be used depending on the power outlet to be used.
6
Do not
Disassemble.
ENGLISH
Various symbols are used in this manual, the user’s manual and on the product itself to ensure correct usage, to prevent danger to the users and to prevent
property damage. The meanings of these symbols are described below. It is important that you read these descriptions thoroughly and fully understand the
contents.
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power
plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an
appropriate extension lead or consult your dealer.
ENGLISH
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and
approval as the original. Ensure the fuse cover is returned to its original position.
Be sure to keep safety ground connection.
Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power
cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.
Be careful in handling the power cord and external connection cables.
Surely connect
If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or
the ground wire.
tension to the power cord and cables. If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer.
• Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this
could result in the inadvertent placing of heavy objects on the concealed power cord or cables.
• Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the
plug or connector.
• Do not place the cord near the heater.
• Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock.
• Do not touch the power plug when lightening is close to you.
• Avoid coiling the power cord and bending it sharply.
• Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit
from the apparatus.
• Do not modify the power cord.
Be careful in handling the battery of the remote control.
Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.
• Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not allow the battery to be exposed to fire or water.
• Avoid fire or high-temperature environment.
• Do not hold the battery with metallic tweezers.
• Keep the battery in a dark, cool and dry place.
• Do not short circuit the battery.
• Do not recharge, disassemble or solder the battery.
• Do not physically impact the battery.
• Use only the battery specified in the manual of this monitor.
• Make sure the plus and minus terminals are correctly aligned when loading the battery.
• If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse
well with water.
• Obey the local laws on disposing the battery.
7
SAFETY INSTRUCTIONS(continued)
CAUTION
Be careful in moving the monitor.
Neglect could result in an injury or damage.
• Do not move the monitor during use. Before moving, disconnect the power plug and all external connections.
• You are advised to move the monitor with two persons.
• Avoid any impact or shock to the monitor; particularly take care of glass screen.
ENGLISH
Do not put anything on top of the monitor.
Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in
households where children are present.
Avoid a humid or dusty place.
Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock.
• Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.
Avoid a high temperature environment.
The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire.
• Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc.
• Do not put the monitor in a place where the temperature is widely changing.
Remove the power cord for complete separation.
• For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time.
• Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.
Disconnect the
plug from the
power outlet.
Never remove the back cover of the monitor as this can expose you to very high voltages and other
hazards
• If the monitor does not operate properly, unplug the monitor and call your authorized dealer or service center.
Prevention of screen burn in
• Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can
cause permanent damage to the monitor. Such “SCREEN BURN IN” constitute misuse and are NOT COVERED by our Factory Warranty.
These servicing instructions are for use by qualified service personnel only
• To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Do not place any objects on top of the monitor
• They may fall or cause a child to climb up to retrieve the objects.
PRECAUTIONS
Installation environment
Do not obstruct a ventilation hole.
Do not put the monitor on carpet or blanket, or near a curtain which has a possibility of obstructing a ventilation hole of the monitor.
Do not put the monitor in the following places.
• Hot places such as near heater, place exposed to the direct rays of the sun.
• A place where the temperature is widely changing.
• Places with soot, dust or high humidity.
• Poor air ventilation place.
• Place near fire.
• A wet place such as bathroom, or shower room.
• Place where you can trip over it.
• Always vibrating or strongly vibrating places.
• Distorted or unstable places.
How to view the monitor
If you use the monitor in too dark a room, your eyes may become tired.
Please use it in a reasonably bright room.
Avoid direct rays of the sun to the screen in order to prevent eye fatigue.
Your eyes will get fatigued after viewing the monitor for long period of time.
Relax your eyes by viewing away from the monitor from time to time.
Please watch the monitor in downward direction.
Note on image retention
The Plasma display illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness
of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.
Please refer to the user manual for this model for instruction on how to use these features.
•
•
•
•
•
•
Ensure screen saver mode is activated.
Always display the image in a mode that fills the screen.
Avoid using split screen mode for long periods of time.
Do not allow the “On Screen Display” to stay on for long periods of time.
Do not display still images, such as menus from game consoles, T/Text, PCs or logos, on the panel for long periods of time.
We recommend that the “Contrast” and “Brightness” level is reduced as much possible.
How to clean the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth
moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.
8
How to clean the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft
cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they
would cause discoloration, scratches or cracks.
Prevention of an obstacle to Radio receivers
This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers.
•
•
•
Keep the monitor away from Radio.
Adjust Radio antennas in order for the monitor not to receive interference.
The antenna cable of Radio should be kept away from the monitor.
You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor.
If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.
•
•
•
•
Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are
properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or
changing connections.
Confirm the connector is fixed tightly when the signal cable is connected.
Also confirm the screws on the connector are tightened.
Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc.
Use a plug with ground terminal and make sure that it connects to the ground.
Precaution during transportation
Please pay attention when you transport this monitor because it is heavy.
Furthermore, use the original carton box and its packaging materials when the monitor is transported.
Failure to transport the monitor in any carton except the original carton may result in damage to the monitor.
Save the original carton box and all packing material.
Do not physically impact the remote control.
• A physical impact could cause damage or malfunction of the remote control.
• Take care not to drop the remote control.
• Do not place heavy objects on the remote control.
Avoid strong rays.
Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.
Avoid radio interference.
Any interfering radiation could cause distorted images or noises.
• Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.
Set the sound volume at a suitable level.
It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.
Precautions for the installation
•
•
•
•
•
•
Do not use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved
stand or legs with the fixings provided according to the instructions.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to
the front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury.
Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.
Only use the attachments/accessories specified by the manufacturer.
Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.
Other precautions
•
•
•
Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or
has a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for
infirm or handicapped people.
Disposal of this product may require specific instructions pertaining to your resident region.
Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!
9
ENGLISH
Precautions for the cable connection
INSTALLATION INSTRUCTIONS
Installation
ENGLISH
Display
Desk top stand
WARNING
Use one of the special mount units to install this product. A mount of insufficient strength or inadequate design can cause overturning or dropping and
result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage caused
by use of other mount units or improper installation.
CAUTION
10cm (4 inches) or more*
• Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this yourself. Ask your
dealer to provide the name of a qualified installer.
• In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches: For a desktop set- up) or
more between the sides and other objects such as walls, etc., so that the ventilation holes are not blocked. (*)
Clamp
Cord
or
chain
Anti-tumble measures
CAUTION
Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.
Securing to a wall or pillar
Using a commercially available cord, chain and clamp, secure the set to a firm wall or pillar.
Hook
Chain
cord or chain
Wall or Pillar
Clamp
Securing desktop
1) Using wood screws (two) fasten the set to the clamping screw holes on the rear of the stand as shown.
2) Using commercially available wood screws, secure the set firmly in position.
Mounting Screw
hole
location
Wood
Two places
10
INSTALLATION INSTRUCTIONS (continued)
Mounting the speaker
ENGLISH
Refer to the instruction manual concerning mounting of the optional speaker unit.
SPEAKER
Power Cord Connection
Connect the power cord, after completing all other connections.
c Connect the power cord to this device.
d Connect the power cord plug to the power outlet.
(The type of plug is different from this drawing for some countries.)
CAUTION
• Use only the power cord provided.
• Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.
WARNING
Be cautious of the power cord connection.
Incorrect connection of the power cord could result in fire or electrical shock.
• Do not touch the power cord with a wet hand.
• Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug.
• Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure.
• Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain anappropriate
extension lead or consult your dealer.
• Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and approval as
the original. Ensure the fuse cover is returned to its original position.
11
INSTALLATION INSTRUCTIONS (continued)
Connecting Signal
Make sure that the power switch of the Display is turned off.
Speaker
(6Ω)
12
Speaker(L)
Display rear panel
Terminal
10 W
Speaker Terminal
(6Ω) 10 W
ENGLISH
Speaker(R)
INSTALLATION INSTRUCTIONS (continued)
Connecting to Video Imaging Device
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
42 ~ 45
(2) Make sure that the power switch of the monitor is turned off.
(3) Make sure that the power switch of the imaging device is turned off.
(4) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this device and
the signal output terminal of the imaging device.
* Cable shown are not supplied with the monitor and are available locally
where ever consumer electronic product are sold.
Display Quick Connection
Monitor rear panel
S-CABLE
CAMCORDER
Speaker(R)
Speaker(L)
AERIEL
SPEAKER TERMINAL
SPEAKER TERMINAL
(6Ω) 10W
(6Ω) 10W
DVD PLAYER
Power Code
Cable/ Satellite Decoder
Box
Best Connection
Basic Connection
VCR
* You can connect regular DVD
player to AV4 IN as well
Better
Connection
ANTENNA/
CABLE
SIGNAL
[An example of connecting video components]
z
z
If the OUTPUT (MONITOR) terminal is connected to a 2nd monitor, it is possible to view the same image as on the main source. The composite
video signal from AV1, AV2 input will be displayed on both screens at the same time.
If video equipment with an S vedio output terminal is used, cabling by the S vedio cable is recommended to provide finer vedio quality. (If an S
vedio input terminal and a vedio input terminal of AV3 connect to the monitor at the same time, S vedio input would govern.)
Applicable video signals for each input terminal
RCA
Terminal
Composite
S-video
AV1
○
○
AV2
○
○
AV3
AV4
RGB1
RGB2
Component
(See PRODUCT SPECIFICATIONS for details, 42 )
D-sub
DVI
RGB 1
RGB 2
Remarks
○
480i, 567i Video Signal only
○
480i, 576i, 480p, 576p, 720p/50, 720p/60, 1080i/50,
1080i/60, inputs Video Signal
○
○
(O: Available)
13
ENGLISH
• See "Product Specifications" concerning the specifications of this device.
INSTALLATION INSTRUCTIONS (continued)
Read SAFETY INSTRUCTIONS ( 6 to 9 ) carefully to ensure maximum safety before proceeding
to these steps:
•
Choose an appropriate site and install the product on a level table where the stand is secure.
•
Make sure that the power switch of this device is turned off.
•
Install the monitor to have ready access to a power socket available.
Con
(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this
device.
• See "Product Specifications" concerning the specifications of this device. 42 ~ 45
(2) Make sure that the power switch of the personal computer is turned off.
(3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this device to the Monitor signal output
terminal of the personal computer.
• Use a cable that fits the input terminal of this device and the output terminal of the personal computer.
• Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with the
personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer or ask the personal
computer manufacturer or your local retail dealer.
Monitor rear panel
Speaker(R)
Speaker (L)
SPEAKER TERMINAL
(6Ω )10W
Power Cable
Connector
SPEAKER TERMINAL
(6Ω )10W
AUDIO IN
RGB 2
DIGITALINPUT
RGB 2
AUDIO IN
RGB 1
ANALOG INPUT
RGB 1
Power
Cord
3.5mm
Stereo
Audio Cable
DVI-D
Connector
15Pin D-Sub
VGA Connector
9-Pin D-Sub
RS-232C connector
To Video
Output
To PC 9-Pin
RS-232C connector
To Audio
Output
PC
Note
•
Please refer to the caution regarding prevention of screen burn in on page 3.
Subwoofer Output provides a single un-amplified audio output that passes along the audio signal from the Plasma Display.
Note: When using a Home Theater audio system with this Plasma Display, please connect the sub woofer (if originally supplied with the audio
system) directly to the Home Theater components subwoofer terminal.
14
ENGLISH
Connecting to a PC
COMPONENT NAMES
NOMS D ES COM POSANT S
Main Unit
Front
ENGLISH
Panel
Control panel
• Adjustment buttons are located
on the bottom.
• The back cover is provided with
indications to distinguish the
adjustment buttons.
Remote-control
receiver 16
MENU button 20
Power lamp 18
SOURCE button
19
• The main power switch is located at the back, on the lower
surface.
Main power switch (See page 18 )
ENTER button
VOLUME UP/DOWN buttons
(
ADJUST buttons) 20
PROGRAM UP/DOWN
buttons
(
SELECT button.) 19
SUB-POWER button (See page 18 )
• (
) indicates the function while the MENU is displayed on the screen.
Caution when moving the main unit
• As this product is heavy, whenever it is moved, two
people are required to transport it safely.
• Whenever the unit is moved it should be lifted forwards
using the two handgrips at the back, and the unit should
then be held at the base on both sides for stability.
Handgrips
Rear
Handgrips
Handgrips
External
Speaker
Terminals
External
Speaker
Terminals
14
14
RGB input terminal
15
COMPONENT NAMES(continued)
Remote Control
POWER ON/OFF button
18
19
SOURCE button
SLEEP button
36
36
ZOOM button
ASPECT button 35
PIP button 28
STILL button 36
36
SWAP button
VOLUME UP/DOWN buttons
19
MENU button
20
ENTER button
20
DISPLAY button
32
AV2 button
19 MUTE button
20
SELECT/ADJUST button
19
AV1 button
19
19
AV3 button
RGB1 button
19
19
19
AV4 button
Loading Batteries
1. Open the battery cover.
Slide back and remove the battery
cover in the direction of the arrow.
RGB2 button
Handing the Remote Control
Handling the Remote Control
Use the remote control within about 5m from the front of the unit’s
remote-control sensor and within 30 degrees on both sides.
2. Load batteries.
Load two Size AAA batteries included observing the Polarities.
With in 30
degrees
About 10 feet
With in 30
degrees
About 10
feet
About 16 feet
3. Close the battery cover.
• Replace the battery cover in the direction of the arrow and snap it
back into place.
ATTENTION
CAUTION
Do not drop or impact the remote control..
Do not splash the remote control with water or put it on a wet object.
z Before leaving the remote control out of use for an extended period of
time, remove the batteries from it.
z
Do not use new and old batteries together. The batteries could explode
or leak, resulting in fires, physical injury, or stains.
z When loading batteries, observe their correct polarities as marked on
z
the product. If loaded in the wrong direction, the batteries could
explode or leak, resulting in fires, physical injury, or stains.
z
z
16
If the remote control begins to lack responsiveness, replace the
batteries.
z Strong light, such as direct sunlight, shining on the photoreceptor of
the remote control can cause operational failure.Position this unit to
avoid direct contact with such light.
ENGLISH
l
COMPONENT NAMES(continued)
Remote Control (continued)
POWER
TV(Optional)
SOURCE
Press this button to turn the TV on or off.
Press this button to choose TV as the
source.
Press this button to select the INPUT
Source.
Press this button to activate the Sleep
Timer menu.
S. MODE
Creates a surround sound effect.
ASPECT
Press this button to select how the
picture is displayed on the screen;
4:3,16:9, Panoramic, or Cinema modes.
PIP
Press this button to show the PIP and
change the size of PIP.
VOL
Press these two buttons to adjust the
volume up or down.
ZOOM
ENGLISH
SLEEP
Press this button to change the picture
size.
MULTI P
Use the
/
PIP setting.
buttons to select the
SWAP
Press this button to exchange main
picture with PIP picture.
STILL
Press this button to freeze the picture.
Press it again to return to normal
operation.
CH
Press these two buttons to select the
channel up or down.
LAST CH
MENU
Press this button to select the On Screen
Display Menu.
Press this button to return to the last
Channel viewed.
MUTE
DISPLAY
Press this button to show the input
signal information.
Press this button to turn off the sound.
Press it once more or press the volume
up button to return the sound.
MTS(Optional)
AV2
Press this button to select the VIDEO 2
or S-VIDEO 2 INPUT.
AV1
Press this button to select the VIDEO 1
or S-VIDEO 1 INPUT.
RGB1
Press this button to select the RGB1
VGA INPUT.
RGB2
Press this button to select the RGB2
DVI-D INPUT.
Press this button to select Multi-channel
television sound. This button operates
only in the TV mode.
NUMBERS KEYPAD(Optional)
Press these buttons to access the
corresponding TV channels.
AV3
Press this button to select the AV3 480i
INPUT.
AV4
Press this button to select the AV4
480p/480i INPUT.
17
OPERATING INSTRUCTIONS
Power lamp
To turn the monitor power ON, press the main power switch on the
monitor main unit to ON, and then press the SUB POWER button or
the ON/OFF or ON button on the remote control.
To turn the monitor power OFF, press the SUB POWER button or
the ON/OFF or OFF button on the remote control, and then press the
main power switch on the monitor main unit to OFF.
z
During normal use, the main power switch is set in the ON position, and
the monitor can then be turned ON/OFF using the SUB POWER button or
the ON/OFF button on the remote control.
Indicating lamp
Indicating
lamp
Power status
Operating
Off
Off
When the main power switch is set
to OFF.
Lights red
Off
(standby)
When the main power switch is ON,
and the OFF button on the remote
control or the SUB POWER button
on the underside of the front of the
frame is OFF.
On
When the main power switch is ON,
and the ON button on the remote
control or the SUB POWER button
on the underside of the front of the
frame is ON.
Off
(Power Save)
When the main power switch is ON,
and the ON button on the remote
control or the SUB POWER button
on the underside of the front of the
frame is ON.
However, the state in POWER
SAVE mode.
Main power switch
Lights green
Lights orange
SUB-POWER button
POWER ON/OFF
button
When the indicating lamp lights in orange or the message “No cable
connected” and “Going to sleep” appears on the screen, there is
something unusual about the status of reception. See “Power Save Mode”
(In RGB1 or RGB2 mode) or “Symptoms That Seemingly Appear to be
Failures.”
39
40
ATTENTION
• Avoid repeatedly turning the monitor on and off at short time intervals.
Failures might result from such operation.
• Turn off the main power switch before leaving the monitor out of use for
an extended period of time.
If a power failure occurs while the main unit is running, it would be
powered on upon recovery from the failure. Turn off the unit main power
switch before leaving the main unit.
18
ENGLISH
Turing Power On and Off
OPERATING INSTRUCTIONS (continued)
The volume can be adjusted by pressing the VOL and
VOL buttons of the remote control (or the and volume
buttons of the monitor unit).
Volume setting value
VOLUME
buttons
UP/DOWN
SOURCE button
15
Adjustment status guide display
TV(Optional)
SOURCE
z
VOLUME
CONTROL
MUTE
When a button is pressed, the volume adjustment status
guide will be displayed.
• The volume will increase when the VOL
button is pressed while the
guide is being displayed.
• The volume will decrease when the VOL
guide is being displayed.
button is pressed while the
Audio Mute
Select
The audio volume can be temporarily muted by pressing the
MUTE button of the remote control.
AV1,AV2,AV3
RGB1,RGB2,AV4
buttons
z
When the MUTE button is pressed, the above icon will
appear.
• The volume setting can be lowered by pressing the VOL
the audio is muted.
• Muting can be cancelled by pressing the VOL
button while the audio is muted.
button while
button or the MUTE
Input Switching
- Input can be switched by pressing the AV1, AV2, AV3, AV4, RGB1, or
RGB2 buttons.
- Input can be switched in the sequence AV1-Video ÆAV1-Svideo Æ
AV2-Video Æ AV2-SVideo Æ AV3 YCbCr Æ AV4 YPbPr/YCbCr Æ
RGB1 VGAÆ RGB2 DVI-D by pressing the SOURCE button and then
select the Input with the select keys
and then press the ENTER
button.
AV1
AV1S
AV2
AV2S
RGB2
RGB1
AV4
AV3
19
ENGLISH
Volume Adjustment
OPERATING INSTRUCTIONS (continued)
When the MENU button is pressed, the adjustment menu
screen will appear. Adjustment and setting are possible by
using the SELECT buttons, PROGRAM ADJUST buttons and
the ENTER button.
Refer to 17 _ 32 concerning the adjustment items and the settings.
Example: Selecting the picture screen
MENU button
PROGRAM/
ADJUST
buttons
SELECT buttons
1. Press the MENU button to display the Main Menu screen.
ENTER button
2. Select the Picture Parameters screen with the and
PROGRAM ADJUST buttons and press the
ENTER button.
3. Use the and
SELECT buttons to select the item to be
adjusted and then use the and to adjust (example:
Brightness.)
• Press the MENU button to return to the previous screen.
• If there is no operation for a period of one minute, the
Adjustment Menu screen will disappear.
20
ENGLISH
Using the Menu Screen
(On-screen display system)
ENGLISH
OPERATING INSTRUCTIONS (continued)
Selected
characters
PICTURE
PARAMETERS
PC PARAMETERS
AUDIO SETTINGS
PICTURE IN
PICTURE
GENERAL
SETTINGS
CONTRAST
AUTO
BASS
PIP POSITION
OSD POSITION
BRIGHTNESS
CLOCK
TREBLE
PIP SIZE
OSD TIMEOUT
COLOR
PHASE
BALANCE
MULTI PIP
OSD LANGUAGE
TINT
POSITION
SURROUND
SLEEP TIMER
COLOR TEMP
I/P INFO
SHARPNESS
FACTORY RESET
BLACK ENHANCE
SCREEN SAVER
POWER SAVE
SCREEN WIPE
GAMMA
STANDBY WHITE
PICTURE NR
INVERSE
21
ENGLISH
PICTURE PARAMETERS
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
CONTRAST
BRIGHTNESS
Black is decreased for overall brightness.
Adjust for imum visibility to suit the ambient
brightness.
Adjust as desired.
COLOR
Decrease color level.
Increase color level.
Adjust as desired.
TINT
Enhances red and weakens green.
Enhances green and weakens red.
This can be adjusted when receiving the signal
and will be greyed out.
Adjust as desired for photo realistic skin color.
22
Broadens the gap between light and dark.
Setup hint
Narrows the gap between light and
dark.
Black is increased for overall darkness.
ENGLISH
PICTURE PARAMETERS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Setup hint
Selected characters
COLOR TEMP
COOL
NORMAL
WARM
USER R
USER G
USER B
Adjust color temperature depending on the user’s preference.
These settings are independently stored in each of the 3 Color
Temperature
23
ENGLISH
PICTURE PARAMETERS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Setup hint
Selected characters
SHARPNESS
BLACK ENHANCE
Softens picture
LOW
Adjust sharpness of picture depending on the user’s preference.
Sharpness picture
MIDDLE
HIGH
OFF
Normally set to LOW. Adjusts the black level compensation.
NOTE
The noise appears on the screen according to the content of the picture when this is set in the direction of
In that case, it is possible to improve it by this setting to the Soft side.
24
Sharp.
ENGLISH
PICTURE PARAMETERS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Setup hint
Selected characters
POWER SAVE
OFF
LOW
HIGH
GAMMA
2.2
2.8
PICTURE NR
ON
OFF
Normally set to OFF.
By this control, power consumption can be reduced or degradation of a panel can
be mitigated. The order of power consumption is HIGH < LOW < OFF..
Normally set to 2.2.
Normally set to ON
If this is set to ON, it helps to reduce the noise interference visible on the screen.
25
OPERATING INSTRUCTIONS (continued)
P
ENGLISH
PC PARAMETERS
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
Setup hint
AUTO
Press the
CLOCK
Reduces the dot clock.
Increases the dot clock.
Adjust for maximum character clarity.
PHASE
Slows the dot clock. Phase.
Advances the dot clock Phase.
Adjust for clear character visibility.
POSITION
Press the ADJUST button to adjust the display position.
ENTER button to make the word “ON” light on.
Normally set to off mode. Adjust automatically for clock, phase
and position.
Adjust the horizontal and vertical display positions.
NOTE
PC PARAMETERS all function could be selected in RGB1 and only position setting active in AV4.
26
ENGLISH
AUDIO SETTINGS
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Setup hint
Selected characters
BASS
Suppresses bass.
Enhances bass.
Adjust to taste.
TREBLE
Suppresses treble.
Enhances treble.
Adjust to taste.
BALANCE
Suppresses right-side sound. Suppresses left-side sound.
SURROUND
OFF
BASIC
ENHANCE
Adjust to taste.
Creates a surround sound effect.
27
PICTURE IN PICTURE (PIP)
SOURCE
PIP
Selecting PIP size
When the PIP button on the remote control is pressed, a black box will appear on
the screen.
SELECT and
Each time the PIP button is pressed, the size of box changes as follows.
OFF
PIP-OFF
SMALL
SMALL
MEDIUM
LARGE
MEDIUM
SPLIT
LARGE
SPLIT
S e l e c t i n g P I P S o u rc e
While a black box appears on the screen, press SOURCE button and PIP SOURCE menu appears.
Picture mode will change in the following sequence, each time the remote button is pressed.
Select the SOURCE by using the
ENTER button
select keys on the remote control. Then, press the
P I P C o m b i n a t i o n Ta b l e
Available signals are limited in PIP mode as shown in the table below.
Sub Source
Main Source
28
AV1
AV2
AV3
AV4
RGB1
RGB2
AV1
X
○
○
○
○
○
AV2
○
X
○
○
○
○
AV3
○
○
X
○
○
○
AV4
○
○
○
X
X
○
RGB1
○
○
○
X
X
○
RGB2
○
○
○
○
○
X
ENGLISH
OPERATING INSTRUCTIONS (continued)
ENGLISH
OPERATING INSTRUCTIONS (continued)
PICTURE IN PICTURE(PIP) (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
PIP POSITION
PIP SIZE
Setup hint
Use the
Use the
buttons to adjust pictures to the up or down positions.
buttons to adjust pictures to the right or left positions.
O FF
S M A LL
M E D IU M
L A RG E
S P LIT
Change PIP display position.
Change PIP display Size.
29
ENGLISH
PICTURE IN PICTURE(PIP) (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Setup hint
Selected characters
MULTI PIP
OFF.
PIP(1+12)
PIP(1+8)
PIP(1+3)
Use the
/
buttons to select the PIP setting.
NOTE
z
z
z
30
Even if the input of the horizontal/vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not change to power
save mode.
Please be careful since image retention will occur if display is left in a MULTI PICTURE display state for a long period of time.
It is normal condition if the sub source is slightly dim while the PIP function is on.
OPERATING INSTRUCTIONS (continued)
ENGLISH
GENERAL SETTINGS
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected
characters
OSD POSITION
OSD TIMEOUT
Setup hint
Use the
buttons to adjust the OSD to right or left position
10 Sec.
20 Sec.
3 Sec.
Adjusts the OSD horizontal position.
Adjusts OSD display and on-screen time.
31
ENGLISH
GENERAL SETTINGS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected characters
OSD LANGUAGE
SLEEP TIMER
I/P INFO
32
Setup hint
ENGLISH
OFF
繁體中文
30 Min.
簡體中文
60 Min.
To display information about the input signal.
120 Min.
Sets the language for the OSD.
Set the display off time for each mode.
Displays information about the input signal.
ENGLISH
GENERAL SETTINGS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected
characters
FACTORY RESET
SCREEN SAVER
Setup hint
ON
OFF
OFF
5 Min.
Resets all settings to FACTORY defaults.
15 Min.
30 Min.
This moves the picture around the screen in small amounts, at set intervals, to
reduce the panel image retention. This is where stationary objects such as screen
logos, leave a slight image visible after they should have disappeared.
33
ENGLISH
GENERAL SETTINGS (continued)
*Press "MENU" button to return to Main Menu, then press “MENU” button to exit OSD.
Selected
characters
SCREEN WIPE
Setup hint
ON
STANDBY WHITE
INVERSE
34
60 Min.
OFF
ON
30 Min.
60 Min.
This is used to reduce the panel image retention theat can occur with stationary pictures
by the white field signal. Select On (continuous operation) or 60 Min. (time limit operation)
and press the ENTER button. Press the MENU button on the remote control to return to
normal viewing.
60 Min.
This function is also provided against the image retention. If time is set for this item, the
screen changes into the white pattern when the monitor enters power save mode, and it
will continue for the period of setting time.
This function can change each level of RGB signal invert to reduce the panel
image retention. When this function is required. Select on (continuous operation) or 60Min.
(time limit operation) and press the ENTER button. And press the Menu or Return button to
exit.
Size Switching (ASPECT)
ASPEC T
ENGLISH
The ASPECT button will select how the video image appears on the monitor’s screen.
There are 4 selections.
16:9
Displays a wide screen image.
4:3
Displays a 4:3 square picture with letterbox bands.
PANORAMIC
Stretches the picture to fill the screen, while leaving
images in the center of the picture the same.
CINEMA
Magnifies the image to fill the screen with a picture.
CINEMA
ASPECT
PANORAMIC
Note:
• You can select 4:3 and 16:9 aspect functions in RGB1 VGA,
RGB 2 DVI and AV4 mode.
• The Aspect function has no active at AV4 1080i, 720p input signals.
When you want to
Play a 4:3 image faithfully in a 16:9
screen in the standard vertical size
and horizontally squeezed.
Play a 4:3 image in a 16:9 screen
faithfully.
Set the display size to
Input signal
16:9
(Squeeze)
4:3
Play a 4:3 image faithfully in a 16:9
screen with the height and witch of
the middle of the screen enlarged on
equal scales and with both sides
appearing somewhat enlarged.
PANORAMIC
Play a 21:9 Cinema size image in the
4:3 image expanded vertically on the
16:9 screen.
CINEMA
Display screen
Remarks
An image with an aspect ratio of 16:9
shrunk horizontally to 4:3 to display in a 4:3
screen.
Blanking occurs on both sides.
(4:3 signal)
(Cinema)
In some cases, some slight blanking may
remain at the top and bottom.
35
ENGLISH
OPERATING INSTRUCTIONS (continued)
ZOOM
Each time the ZOOM button of the remote control is pressed, the
Image on the screen will be enlarged. There are 10 selections,
Zoom 0(=Normal size) to Zoom 9.
SLEEP
ZOOM
DISPLAY
SWAP
STILL
Press this button to show the input signal information.
STILL
DISPLAY
Press this button to freeze the picture.
Press it again to return to normal operation.
SLEEP
Press this button to activate the SLEEP TIMER menu.
SWAP
Press this button to exchange main picture with PIP picture.
OTHER FEATURES
Automatic Store
e
Approximately 1 sec. after adjustment is completed; the adjustments will be recorded as shown in the table below.
Menu
Display
CONTRAST
BRIGHTNESS
Registration condition
For every input function, 1 setting is
registered.
Display
PIP SIZE
MULITI PIP
TINT
OSD POSITION
OSD TIMEOUT
OSD LANGUAGE
SLEEP TIMER
I/P INFO
FACTORY RESET
SCREEN SAVER
SCREEN WIPE
STANDBY WHITE
INVERSE
SHARPNESS
BLACK ENHANCE
POWER SAVE
GAMMA
PICTURE NR
BASS
TREBLE
For every Audio Mode, 1 setting is
registered.
BALANCE
1 setting is registered.
SURROUND
For every Audio Mode, 1 setting is
registered.
Registration condition
PIP POSITION
COLOR
COLOR TEMP
36
Menu
1 setting is registered.
1 setting is registered.
● The previously recorded items will be lost.
● The signal mode can be identified by the horizontal/vertical sync
frequency and the sync signal polarity. Different signals where all the
elements are the same or similar will be handled as the same signal.
ENGLISH
OTHER FEATURES (continued)
Signal Check (RGB Input)
Changes in the signal status are displayed on the screen.
Status
Display
Action
When Mode display is set to
A guide is displayed for the
ON, the input signal is switched. input terminal.
When the sync signal is no
longer detected.
A guide displays No sync.
Recheck the personal computer
Detected, and Power Save (for power switch status and the
approx. 5 sec.)
connection status.
When the condition continues
where the sync signal cannot be
detected, indicator lamp of
power source changes to
orange and the mode switches
to power save mode.
When the input signal does not A guide displays Invalid Mode.
match the monitor specifications
or is in an unstable status.
Recheck the input signal
specifications.
39
~ 41
Power Save mode (RGB Input)
When the RGB1, RGB2 input is selected
●When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the computer is not being
used to reduce power consumption by this unit.
RGB sync signal
Horizontal
Yes
No
Yes
No
Vertical
Yes
Yes
Non
No
PC signal
Active (normal display)
Blank (no display)
Operation mode
On
Off
Indicating lamp
Lights green
Lights orange
Power consumption
280W
3W or less (RGB1,RGB2)
Returning to operating status
●Operate the personal computer, or press either the INPUT SELECT button of the main unit or the RGB1/RGB2 buttons of the remote control.
37
There are different characteristics that result in panel image retention depending on how the plasma display is used.
Situations and effective usage methods related to ghosting are provided below.
Image retention characteristics of a plasma display
The image retention phenomenon of a plasma panel occurs because of partial phosphor degradation arising from partial character and figure display.
For example, when the character image as shown in Fig. A at the right is continuously
displayed for a long period of time, the only part of the phosphor (Red, Green, Blue) that will
degrade will be the color of the applicable character display portion. Consequently, when a
white image is displayed on the entire screen as shown in Fig. a, the character marks
displayed up to that time will become a color difference visible to the eye.
Fig. A
Fig. a
„ The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.
• The tendency of the phosphor is to degrade more the brighter the characters and figures
are displayed. When images of figures with different levels of brightness, as shown in Fig.
B, are continuously displayed for a long period of time, it becomes easier to see image
marks at locations when the brighter figures are displayed to see.
Fig. B
Fig. b
* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention is seen differs
depending on the operation time and brightness.
Methods to Reduce the Occurrence of Image Retention
• Lower the Contrast and Brightness settings of the plasma display as much as possible.
• Set the plasma monitor to "Screen Wipe" or "Inverse" display.
The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be reduced by displaying
a reversed color or completely white screen for about 1 ~ 2 hours after terminating the display.
(Settings can be made using Screen Wipe and Inverse of Function MENU shown on 30 )
• Using in combination with moving images
Since the degradation of the fluorescent material progresses comparatively uniformly for moving images, the occurrence of partial image
retention can be minimized .We recommend to use in combination with moving images such as a DVD.
* Please be careful since image retention will occur if display is left in a two screen display state for a long period of time.
* Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut and broadcast
station name or time are displayed in the same portion of the screen. Image retention in these portions can be expected to occur, so please be aware.
NOTES
About screen defects
• High precision technology is used in the making of plasma panels but there may be dark spots (points that do not illuminate) and bright spots (points that are
too bright) in some cases. These do not indicate a malfunction.
About residual images
• In some cases, residual images may remain after the short-term display of still images and another image is displayed , but these will disappear and return to
normalcy. This is not a malfunction.
About the panel screen
• Plasma displays display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel surface may rise in some
cases. Also, plasma displays are made of finely processed glass. A reinforced glass filter is installed over the panel surface but avoid strong impact because
there is still danger of glass breakage.
38
ENGLISH
IMAGE RETENTION OF PLASMA DISPLAY
ENGLISH
TROUBLESHOOTING
Symptoms That Seemingly Appear to be Failures
Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.
WARNING
Self servicing can be hazardous.
Symptom
● There is no picture and the power-indicating lamp is
off.
In RGB mode, the message “No cable connected”
and “Going to sleep” is displayed.
● In Video mode, the message “No sync Detected” is
displayed.
● There is no picture and the power indicating lamp
lights orange.
●
Point to check
● Check to see that the power cable is properly connected.
● Press the main switch.
No sync signal is detected.
● Check that the signal cable is properly connected.
● Make sure that the computer, imaging equipment, etc., is turned
● The power indicating lamp is lit normally but there is
● Check the contrast and brightness settings (adjust them for higher
Text displayed across the screen appears vertically
streaked, with the characters in vertical columns
blurred.
● Text displayed across the screen appears blurred.
A fine pattern flickers when displayed on the screen.
14
on.
An input signal is received abnormally.
● Ensure that the input signal matches the monitor specifications.
● Check to see that the signal cable is properly connected.
● The display image appears slanted.
11
13
● Make sure the computer is not in power-save mode.
● Ensure that the input selection matches the connection terminal.
● The message “Invalid Mode.” is displayed.
no picture.
See Page
14
22
contrast and brightness).
● Check to see that the signal cable is properly connected.
14
● Adjust the clock frequency and the phase. (Adjust the clock
26
frequency first, the dot clock phase next.)
(RGB input)
● Adjust the clock phase till the desired clarity is obtained.
(RGB input)
43
26
43
● The remote control does not work.
● Ensure that the batteries in the remote control are inserted with
the correct polarity.
16
● Check to see that the batteries in the remote control are functional.
39
Symptoms That Seemingly Appear to be Failures(continued)
Symptom
y The temperature of the display panel surface is high.
Point to check
y The plasma display panel is lighting the phosphors by the discharge of
internal radiantion. In some cases, this may cause the temperature of the
panel surface to increase. Please note that this is not a malfunction.
See Page
-
y There are locations on the screen that are different from the y High-precision technology is used to manufacture the plasma display panel,
periphery(*)
however in some cases; there are minor defects in some parts of the screen.
* Points that do not light, points with brightness different
Please note that this is not a malfunction.
from that of the periphery, points with color different from
that of the periphery, etc.
-
y Vertical stripes appear, depending on the screen contents. y The plasma display panel is lighting the phosphors on it by the discharge of
internal radiation. Depending on the screen contents, in rare cases this may
cause vertical stripes to appear because of failure to light. Please note that
this is not a malfunction.
-
y Coarse horizontal stripes appear in16:9 display.
y Adjusting the Clock Phase will reduce the horizontal stripes.
(RGB input)
y Flickering in the form of horizontal lines oscillating up and
down.
(RGB INPUT only)
y If the direct frequency from the computer is below 85Hz, try a higher
frequency (upper limit 85Hz). There may be a slight attenuation of the current
image.
-
y The top of the monitor heats up.
y When used for long periods of time, the top surface of the monitor may heat
up. This is not a malfunction.
-
y Text characters are displayed with varying thicknesses.
y The thicknesses of characters and lines may vary if images with a vertical
resolution greater than 480 lines are displayed; however this is not a
malfunction.
-
y The ambient temperature of the monitor may be low. When used in the
ambient temperatures less than about 15 degrees, it may cause lower
luminance. It happens in an operation of the panel protect circuit, and this is
not a malfunction. The luminance will recover by turning on electricity for a
while.
-
y The brightness contrast in the display seems not bright
enough.
40
26
ENGLISH
TROUBLESHOOTING (continued)
Actions to Correct Abnormal Displays
Corrections d'affichage anormales RVB 1 seulement
Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. (only
for RGB1)
Symptom 1
Text displayed across the screen appears vertically streaked, with some characters blurred (Figure 1).
The display image appears flowing (Figure 2) (RGB input).
Example
Figure 1
Vertical Streaks
Before adjustment.
Some characters are blurred.
After adjustment.
All characters appear
crisp now.
After adjustment.
All characters are
blurred.
Adjustment
procedure
1) Press the MENU button. The Main Menu will be displayed.
2) Press the
button and Select PC PARAMETERS.
3) Press the ENTER button.
4) Press the
SELECT button and select Auto.
5) Press the ENTER button twice to auto configuration.
When adjustment is not possible with Auto Adjust:
6) Press the MENU button. The Main Menu will be displayed.
7) Press the
button and select PC PARAMETERS.
8) Press the ENTER button.
9) Press the
SELECT button and select Clock.
10) Press the or buttons and search for clear characters over the entire screen.
11) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.
z
The display image may be momentarily disturbed during clock adjustment but this is not a failure.
Symptom 2
Text displayed across the screen appears blurred in its entirety (Figure 2).
A fine pattern flickers when displayed on the screen (Figure 3).
Example
Figure 2
Adjustment
procedure
1) Press the MENU button. The Main Menu will be displayed.
2) Press the
button and Select PC PARAMETERS.
3) Press the ENTER button.
4) Press the
SELECT button and select Auto.
5) Press the ENTER button twice to auto configuration.
Before adjustment
Figure 3
Before adjustment
After adjustment
After adjustment
When adjustment is not possible with Auto Adjust
6) Press the MENU button. The Main Menu will be displayed.
7) Press the
button and select PC PARAMETERS.
8) Press the ENTER button.
9) Press the
SELECT button and select PHASE.
(Displays fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)
10) Press
screen.
or
buttons to make the text appear clean across the
10) Press
flickering.
or
buttons to make the text appear without
41
ENGLISH
TROUBLESHOOTING (continued)
PRODUCT SPECIFICATIONS
Panel
Display
dimensions
Resolution
Approx. 42 inches (920 (H) x 518 (V) mm, diagonal 1059mm)
852 (H) x 480 (V) pixels
Net dimensions
1030 (W) x 636 (H) x 91 (D) mm(excluding Speakers/Stand)
1232 (W) x 711.5 (H) x 300 (D) mm(including Speakers/Stand)
Net weight
33kg(excluding Speakers/Stand)
42kg(including Speakers/Stand)
Ambient
conditions
Temperature
Relative humidity
Operating: 5°C to 35°C, Storage: -15°C to 60°C
Operating: 20% to 80%, Storage: 20% to 90% (non-condensing)
Power supply
AC100 - 240V, 50/60Hz
Power consumption/at standby
280W / <3W
Audio output
10W + 10W (6 Ω) (Without speaker)
(RGB input)
Input signals
Input terminals
RGB1-VGA analog RGB input terminal (D-sub 15-pin)
RGB1-VGA audio input terminal (3.5mm Stereo Mini Jack)
RGB2 DVI-D input terminal (DVI-D)
RGB2 DVI-D audio input terminal (3.5mm Stereo Mini Jack)
Video signals
0.7 V
Sync signals
H/V separate, TTL level [2k Ω]
H/V composite, TTL level [2k Ω]
Sync on green, 0.3 Vp-p [75 Ω]
Recommended signal
45 modes
44
45
(Video input)
Input terminals
AV1 : Composite video input terminal(RCA)
AV1 : S video input teminal
AV1 : L/R audio input terminal(RCA)
AV2 : Composite video input terminal(RCA)
AV2 : S video input teminal
AV2 : L/R audio input terminal(RCA)
AV3 : Component input (Y-CbCr) (RCA)
AV3 : L/R audio input terminal (RCA)
AV4 : Component input (YPbPr/ YCbCr) (RCA)
AV4 : L/R audio input terminal (RCA)
Video signals
AV1 : PAL, SECAM, NTSC
AV2 : PAL, SECAM, NTSC
AV3 : 480i, 576i
AV4 : 480i, 576i, 480p, 576p, 720p/50, 720p/60, 1080i/50, 1080i/60,
Input signals
Video output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
Recommended signal
13 modes
44
45
• It takes at least 30 minutes to attain the maximum picture quality.
42
ENGLISH
SPÉCIFIC AT ION S DU PR ODUIT
ENGLISH
PRODUCT PECIFICATIONS (Continued)
Signal Input
RGB1 Input (D-sub 15-pin connector)
Pin
Input signal
1
R
2
G or sync on green
3
B
4
No connection
5
No connection
6
R.GND
7
G.GND
• When different kinds of input signals are simultaneously input to the
monitor via a graphics board or the like, the monitor will automatically
select the signals in the following priority order:
8
B.GND
9
No connection
Sync signal type
10
GND
H/V separate sync.
1
11
No connection
H/V composite sync.
2
sync.on Green *
3
12
[SDA]
13
H. sync or H/V composite sync
14
V.sync. [V.CLK]
15
[SCL]
Frame
GND
Priority
*Even in the case of the recommended signals shown on the following
page, there may be instances when correct display is not possible. In
this case, use H/V separate sync, or H/V composite sync.
RGB2 (DVI-D) Input
Pin
Input signal
1
Pin
Input signal
T.M.D.S. Data2-
14
+5V Power
2
T.M.D.S. Data2+
15
Ground (for+5V)
3
T.M.D.S. Data2/4 Shield
16
Hot Plug Detect
4
T.M.D.S. Data4-
17
T.M.D.S. Data0-
5
T.M.D.S. Data4+
18
T.M.D.S. Data0+
6
DDC Clock
19
T.M.D.S. Data0/5 Shield
7
DDC Data
20
T.M.D.S. Data5-
8
No Connect
21
T.M.D.S. Data5+
9
T.M.D.S. Data1-
22
T.M.D.S. Clock Shield.
10
T.M.D.S. Data1+
23
T.M.D.S. Clock+
11
T.M.D.S. Data1/3 Shield
12
T.M.D.S. Data3-
13
T.M.D.S. Data3+
24
T.M.D.S. Clock-
Frame
GND
S-input connector pin specifications
Pin
Input signal
1
Y
2
Y-GND
3
C
4
C-GND
Frame
GND
RS232C Connector Pin Specification
Pin
1
Input signal
NC
Remarks
2
RXDO
Ground (for+5V)
3
TXDO
Hot Plug Detect
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
10
GND
T.M.D.S. Data0+
43
Recommended Signal List
With Composite Input and S-video Input (AV1~AV2 input)
No.
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
1
NTSC-M
525
59.94
15.734
2
PAL
625
50
15.63
3
SECAM
625
50
15.63
Remarks
With Y, Cb, Cr input (AV3 component input)
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
1
480i
480
59.94
15.734
2
576i
625
50
15.63
No.
Remarks
With Y, Cb, Cr / Y, Pb, Pr input (AV4 component input)
Signal mode
Signal name
Resolution
Vertical frequency (Hz)
Horizontal
frequency (kHz)
1
480i
480
60
15.734
2
576i
576
50
15.63
3
480p
480
60
31.47
4
576p
576
50
31.26
5
720p/50
720
50
37.5
6
720p/60
720
60
44.96
7
8
1080i/50
1080i/60
1080
1080
50
60
28.13
33.75
No.
Remarks
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities. Note
that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 480 lines of vertical resolution at Full display (compressed display) can result in the interpolation of stripes.
With Analog RGB signal input (RGB 1 input)
Signal mode
No.
Horizontal frequency
(kHz)
Dot clock frequency
(MHz)
Resolution
Vertical frequency
(Hz)
1
640 x 400
70.08
31.47
25.18
2
3
640 x 480
864 x 480
59.94
59.94
31.47
31.47
25.18
34.24
4
640 x 480
72.81
37.86
31.50
5
640 x 480
75.00
37.50
31.50
6
640 x 480
85.01
43.27
36.00
7
8
800 x 600
800 x 600
56.25
60.32
35.16
37.88
36.00
40.00
9
800 x 600
72.19
48.08
50.00
10
800 x 600
75.00
46.88
49.50
11
800 x 600
85.06
53.67
56.25
12
13
1024 x 768
1024 x 768
60.00
70.07
48.36
56.48
65.00
75.00
14
1024 x 768
75.03
60.02
78.75
15
1024 x 768
85.00
68.68
94.50
16
1152 X 864
75.00
67.50
108.00
17
18
1280 X 1024
1600 X 1200
60.02
60.00
63.98
75.00
108.00
162.00
19
640 X 480
66.67
35.00
30.24
20
832 X 624
74.55
49.72
57.28
21
1024 X 768
74.93
60.24
80.00
22
1152 X 870
75.06
68.68
100.00
23
24
1280 x 768
1280 x 768
59.833
69.997
47.986
56.137
81.00
94.76
25
1366 x 768
60.015
47.712
89.50
44
ENGLISH
PRODUCT SPECIFICATIONS (continued)
• The monitor differentiates the signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal polarities. Note
that different signals having all these elements alike may be handled as the same signal.
• Displaying images with more than 480 lines of vertical resolution at Full display (compressed display)can result in the interpolation of stripes
With Digital RGB signal input (RGB 2 input)
Signal mode
No.
1
2
3
Signal name
VGA
W-VGA
Resolution
Vertical frequency
(Hz)
Horizontal frequency
(kHz)
Dot clock frequency
(MHz)
640 x 400
70.08
31.47
25.18
640 x 480
59.94
31.47
25.18
864 x 480
59.94
31.47
34.24
4
640 x 480
72.81
37.86
31.50
5
640 x 480
75.00
37.50
31.50
6
640 x 480
85.01
43.27
36.00
7
800 x 600
56.25
35.16
36.00
8
9
800 x 600
800 x 600
60.32
72.19
37.88
48.08
40.00
50.00
10
800 x 600
75.00
46.88
49.50
11
800 x 600
85.06
53.67
56.25
12
1024 x 768
60.00
48.36
65.00
13
14
1024 x 768
1024 x 768
70.07
75.03
56.48
60.02
75.00
78.75
VESA
15
480p
720 x 480
59.94
31.47
27.00
16
576P
720 x 576
50.00
31.25
27.00
17
720p/50
1280 x 720
50.00
37.50
74.29
18
19
720p/60
1080i/50
1280 x 720
1280 x 720
60.00
50.00
45.00
28.13
74.25
74.25
20
1080i/60
1920 x 1080
60.00
33.75
74.25
45
ENGLISH
• The type of video board or connecting cable used, may not allow for correct display adjustment of Horizontal Position, Vertical Position, Horizontal Clock
and Clock Phase.
• The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it.
If problems remain after checking this manual, please contact your place of purchase, visit the Customer Support section of Mitsubishi
Electric Australia’s web site at www.mitsubishielectric.com.au for details of your nearest Mitsubishi Electric Authorised Service Center, or
contact the Service Department for your state:
New South Wales and Australian Capital Territory
348 Victoria Road
Rydalmere, NSW, 2116
Telephone: (02) 1300 651-808
Fax: (02) 9684-7684
Queensland
Unit 12 469 Nudgee Road
Hendra, QLD, 4011
(Airlink Business Park)
Telephone: (07) 3623-2000
Fax: (07) 3630-1888
South Australia and Northern Territory
77 Port Road
Hindmarsh, SA, 5007
Telephone: (08) 8340-0444
Fax: (08) 8340-0555
Victoria and Tasmania
4 / 303 Burwood Hwy
East Burwood, VIC, 3151
Telephone: (03) 9262-9899
Fax: (03) 9262-9850
Western Australia
5 / 329 Collier Road
Bassendean, WA, 6054
Telephone: (08) 9377-3411
Fax:(08) 9377-3499
46
ENGLISH
Service Contacts
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement