PCISA-9102 Half-Size CPU Card User Manual

PCISA-9102 Half-Size CPU Card User Manual
PCISA -9102 Half-Size CPU Card
PCISA-9102 Half-size CPU Card
Page I
PCISA-9102 Half-Size CPU Card
Revision
Date
Version
Changes
2008-07
1.00
Initial Release
Page II
PCISA -9102 Half-Size CPU Card
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page III
PCISA-9102 Half-Size CPU Card
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the PCISA-9102 or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the PCISA-9102. Cautions are easy to recognize. The word “caution” is written
as “CAUTION,” both capitalized and bold and is followed. The italicized text is the
cautionary message. A caution message is shown below:
Page IV
PCISA -9102 Half-Size CPU Card
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the PCISA-9102.
Please take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the PCISA-9102. Please take
note messages seriously.
Page V
PCISA-9102 Half-Size CPU Card
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the PCISA-9102 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
The items listed below should all be included in the PCISA-9102 package.
1 x PCISA-9102 CPU card
1 x IDE flat cable
1 x Mini jumper pack
1 x Parallel port and RS-232 cable
2 x SATA cables
1 x SATA power cable
1 x USB cable
1 x Utility CD
1 x Quick installation guide
Images of the above items are shown in Chapter 3.
Page VI
PCISA -9102 Half-Size CPU Card
Table of Contents
1
INTRODUCTION..................................................................................................... 1
1.1 PCISA-9102 OVERVIEW ............................................................................................ 2
1.1.1 PCISA-9102 Features ........................................................................................ 3
1.1.2 PCISA-9102 Model Variation ............................................................................ 3
1.2 PCISA-9102 BOARD OVERVIEW ............................................................................... 4
1.2.1 PCISA-9102 Connectors.................................................................................... 5
1.2.2 Technical Specifications..................................................................................... 6
2
DETAILED SPECIFICATIONS ............................................................................. 9
2.1 OVERVIEW ............................................................................................................... 10
2.2 DIMENSIONS ............................................................................................................ 10
2.2.1 Board Dimensions............................................................................................ 10
2.2.2 External Interface Panel Dimensions .............................................................. 12
2.3 DATA FLOW .............................................................................................................. 12
2.4 COMPATIBLE PROCESSORS ....................................................................................... 14
2.5 INTEL® 910GMLE GRAPHICS AND MEMORY CONTROLLER HUB ............................ 14
2.5.1 Intel® 910GMLE Overview .............................................................................. 14
2.5.2 Intel® 910GMLE Front Side Bus (FSB) Support ............................................ 14
2.5.3 Intel® 910GMLE Memory Support .................................................................. 15
2.5.4 Intel® 910GMLE Integrated Graphics............................................................. 16
2.5.4.1 Intel® 910GMLE Analog CRT Support .................................................... 17
2.5.4.2 Intel® 910GMLE LVDS Support .............................................................. 17
2.5.4.3 Intel® 910GMLE SDVO Support ............................................................. 18
2.5.5 Intel® 910GMLE Direct Management Interface (DMI)................................... 18
2.6 INTEL® ICH6-M I/O CONTROLLER HUB.................................................................. 19
2.6.1 Intel® ICH6-M Overview ................................................................................. 19
2.6.2 Intel® ICH6-M Audio Codec ’97 Controller.................................................... 20
2.6.3 Intel® ICH6-M IDE Interface........................................................................... 21
2.6.4 Intel® ICH6-M Low Pin Count (LPC) Interface .............................................. 22
2.6.5 Intel® ICH6-M PCI Interface........................................................................... 22
2.6.5.1 Winbond W83628 PCI-to-ISA Bridge ...................................................... 22
Page VII
PCISA-9102 Half-Size CPU Card
2.6.6 Intel® ICH6-M PCIe x1 Bus............................................................................. 23
2.6.7 Intel® ICH6-M Real Time Clock ...................................................................... 23
2.6.8 Intel® ICH6-M SATA Controller ...................................................................... 24
2.6.9 Intel® ICH6-M USB Controller........................................................................ 24
2.7 PCIE BUS COMPONENTS .......................................................................................... 25
2.7.1 PCIe Bus Overview .......................................................................................... 25
2.7.2 Broadcom BCM5787M PCIe GbE Controller ................................................. 25
2.8 LPC BUS COMPONENTS ........................................................................................... 26
2.8.1 LPC Bus Overview........................................................................................... 26
2.8.2 BIOS Chipset.................................................................................................... 27
2.8.3 Winbond W83627EHG Super I/O Chipset ....................................................... 27
2.8.3.1 Super I/O LPC Interface ........................................................................... 28
2.8.3.2 Super I/O UART Controller...................................................................... 29
2.8.3.3 Super I/O Infrared ..................................................................................... 29
2.8.3.4 Super I/O Hardware Monitor Functions ................................................... 29
2.8.3.5 Super I/O Parallel Port .............................................................................. 29
2.8.3.6 Super I/O Floppy Disk Drive (FDD) Controller....................................... 30
2.8.3.7 Super I/O Keyboard and Mouse Controller .............................................. 31
2.8.3.8 Super I/O GPIO Ports ............................................................................... 31
2.8.3.9 Super I/O Fan Speed and Fan Control ...................................................... 31
2.9 ENVIRONMENTAL AND POWER SPECIFICATIONS ....................................................... 31
2.9.1 System Monitoring ........................................................................................... 31
2.9.2 Operating Temperature and Temperature Control........................................... 32
2.9.3 Power Consumption......................................................................................... 33
3
UNPACKING .......................................................................................................... 34
3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 35
3.2 UNPACKING.............................................................................................................. 35
3.2.1 Unpacking Precautions.................................................................................... 35
3.3 UNPACKING CHECKLIST ........................................................................................... 36
3.3.1 Package Contents............................................................................................. 36
3.3.2 Optional Items.................................................................................................. 37
4
CONNECTORS AND JUMPERS ......................................................................... 39
4.1 PERIPHERAL INTERFACE CONNECTORS .................................................................... 40
Page VIII
PCISA -9102 Half-Size CPU Card
4.1.1 PCISA-9102 Layout ......................................................................................... 40
4.1.2 Peripheral Interface Connectors ..................................................................... 41
4.1.3 Rear Panel Connectors .................................................................................... 42
4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 43
4.2.1 ATX Power Supply Enable Connector ............................................................. 43
4.2.2 Audio Connector .............................................................................................. 44
4.2.3 CompactFlash® Socket.................................................................................... 45
4.2.4 Digital Input/Output Connector....................................................................... 47
4.2.5 Fan Connector ................................................................................................. 48
4.2.6 Floppy Disk Connector (34-pin)...................................................................... 49
4.2.7 Front Panel Connector .................................................................................... 51
4.2.8 IDE Connector ................................................................................................. 52
4.2.9 Infrared Interface Connector ........................................................................... 54
4.2.10 Keyboard/Mouse Connector .......................................................................... 55
4.2.11 LCD Backlight Connector.............................................................................. 56
4.2.12 LVDS LCD connector .................................................................................... 57
4.2.13 Parallel Port Connector ................................................................................ 58
4.2.14 Power Connector ........................................................................................... 59
4.2.15 SATA Drive Connectors ................................................................................. 60
4.2.16 SDVO Connector............................................................................................ 61
4.2.17 Serial Port Connector (COM 1, RS-232)....................................................... 63
4.2.18 Serial Port Connector (COM 2, RS-232/422/485) ........................................ 64
4.2.19 Internal USB Connectors............................................................................... 65
4.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 67
4.3.1 CRT Connector ................................................................................................ 67
4.3.2 Ethernet Connectors ........................................................................................ 68
4.3.3 USB Connector ................................................................................................ 69
5
INSTALLATION .................................................................................................... 70
5.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 71
5.2 INSTALLATION CONSIDERATIONS ............................................................................. 72
5.2.1 Installation Notices .......................................................................................... 72
5.2.2 Installation Checklist ....................................................................................... 73
5.3 CPU, CPU COOLING KIT AND DIMM INSTALLATION ............................................. 74
5.3.1 Socket 479 CPU Installation............................................................................ 74
Page IX
PCISA-9102 Half-Size CPU Card
5.3.2 Cooling Kit CF-479B-RS Installation.............................................................. 76
5.3.3 DIMM Installation ........................................................................................... 78
5.4 JUMPER SETTINGS .................................................................................................... 80
5.4.1 AT Power Select Jumper Settings..................................................................... 81
5.4.2 CF Card Setup ................................................................................................. 82
5.4.3 Clear CMOS Jumper........................................................................................ 83
5.4.4 COM 2 Function Select Jumper....................................................................... 84
5.4.5 CPU Frequency Selection ................................................................................ 85
5.4.6 LVDS Voltage Selection.................................................................................... 86
5.4.7 LVDS Panel Resolution Selection .................................................................... 87
5.5 CHASSIS INSTALLATION ........................................................................................... 89
5.5.1 Airflow.............................................................................................................. 89
5.5.2 Backplane Installation ..................................................................................... 89
5.5.3 CPU Card Installation ..................................................................................... 90
5.6 INTERNAL PERIPHERAL DEVICE CONNECTIONS........................................................ 90
5.6.1 Peripheral Device Cables ................................................................................ 90
5.6.2 IDE Cable Connection..................................................................................... 91
5.6.3 SATA Drive Connection ................................................................................... 92
5.6.4 USB Cable (Dual Port) with Slot Bracket ....................................................... 93
5.6.5 7.1 Channel Audio Kit Installation (Optional) ................................................ 94
5.7 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 96
5.7.1 LAN Connection (Single Connector) ............................................................... 96
5.7.2 VGA Monitor Connection ................................................................................ 97
5.7.3 USB Device Connection (Single Connector) ................................................... 98
6
AMI BIOS.............................................................................................................. 100
6.1 INTRODUCTION ...................................................................................................... 101
6.1.1 Starting Setup................................................................................................. 101
6.1.2 Using Setup .................................................................................................... 101
6.1.3 Getting Help................................................................................................... 102
6.1.4 Unable to Reboot After Configuration Changes............................................ 102
6.1.5 BIOS Menu Bar.............................................................................................. 102
6.2 MAIN ..................................................................................................................... 103
6.3 ADVANCED ............................................................................................................. 104
6.3.1 CPU Configuration........................................................................................ 105
Page X
PCISA -9102 Half-Size CPU Card
6.3.2 IDE Configuration ......................................................................................... 106
6.3.2.1 IDE Master, IDE Slave ........................................................................... 108
6.3.3 Floppy Configuration......................................................................................113
6.3.4 Super IO Configuration...................................................................................114
6.3.5 Hardware Health Configuration.....................................................................117
6.3.6 Remote Access Configuration .........................................................................119
6.3.7 USB Configuration......................................................................................... 122
6.4 PCI/PNP ................................................................................................................ 125
6.5 BOOT ..................................................................................................................... 127
6.5.1 Boot Settings Configuration........................................................................... 128
6.5.2 Boot Device Priority ...................................................................................... 130
6.5.3 Removable Drives .......................................................................................... 131
6.6 SECURITY............................................................................................................... 132
6.7 CHIPSET ................................................................................................................. 133
6.7.1 Northbridge Configuration ............................................................................ 133
6.7.2 Southbridge Configuration ............................................................................ 136
6.8 POWER ................................................................................................................... 137
6.9 EXIT ....................................................................................................................... 138
7
SOFTWARE DRIVERS ....................................................................................... 141
7.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 142
7.2 DRIVER CD AUTO-RUN .......................................................................................... 142
7.3 CHIPSET DRIVER INSTALLATION............................................................................. 144
7.4 VGA DRIVER ......................................................................................................... 146
7.5 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION .................................. 150
7.6 INTEL® MATRIX STORAGE MANAGER DRIVER INSTALLATION ............................... 154
A
BIOS CONFIGURATION OPTIONS ............................................................. 161
A.1 BIOS CONFIGURATION OPTIONS........................................................................... 162
B
TERMINOLOGY ................................................................................................. 165
C
WATCHDOG TIMER .......................................................................................... 170
D
ADDRESS MAPPING.......................................................................................... 173
D.1 IO ADDRESS MAP ................................................................................................. 174
D.2 1ST MB MEMORY ADDRESS MAP ......................................................................... 174
Page XI
PCISA-9102 Half-Size CPU Card
D.3 IRQ MAPPING TABLE ............................................................................................ 175
D.4 DMA CHANNEL ASSIGNMENTS ............................................................................. 175
E
COMPATIBILITY................................................................................................ 176
E.1 COMPATIBLE PROCESSORS ..................................................................................... 177
E.2 COMPATIBLE MEMORY MODULES.......................................................................... 177
F
HAZARDOUS MATERIALS DISCLOSURE ................................................... 179
F.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 180
G
INDEX.................................................................................................................... 183
Page XII
PCISA -9102 Half-Size CPU Card
List of Figures
Figure 1-1: PCISA-9102 CPU Card...............................................................................2
Figure 1-2: PCISA-9102 Board Overview (Front Side)...............................................4
Figure 1-3: PCISA-9102 Board Overview (Solder Side).............................................5
Figure 2-1: PCISA-9102 Dimensions (mm) ...............................................................11
Figure 2-2: External Interface Panel Dimensions (mm)...........................................12
Figure 2-3: Data Flow Block Diagram........................................................................13
Figure 2-4: Front Side Bus (FSB)...............................................................................15
Figure 2-5: 240-pin DDR2 DIMM Socket ....................................................................16
Figure 2-6: Integrated Graphics Interfaces...............................................................16
Figure 2-7: DMI Chip-to-Chip Connection.................................................................19
Figure 2-8: Audio Connector......................................................................................21
Figure 2-9: PCI-to-ISA Bridge.....................................................................................23
Figure 2-10: SATA Drive Connectors ........................................................................24
Figure 2-11: Onboard USB Implementation .............................................................25
Figure 2-12: Broadcom BCM5787M PCIe GbE Controllers .....................................26
Figure 2-13: BIOS Chipset..........................................................................................27
Figure 2-14: Winbond W83627EHG Super I/O ..........................................................28
Figure 4-1: Connector and Jumper Locations (Front Side) ....................................40
Figure 4-2: Connector and Jumper Locations (Solder Side)..................................41
Figure 4-3: ATX Power Supply Enable Connector Location...................................43
Figure 4-4: Audio Connector Location......................................................................44
Figure 4-5: CF Card Socket Location ........................................................................46
Figure 4-6: GPIO Connector Location.......................................................................48
Figure 4-7: Fan Connector Locations .......................................................................49
Figure 4-8: 34-pin FDD Connector Location.............................................................50
Figure 4-9: Front Panel Connector Location............................................................51
Figure 4-10: IDE Device Connector Location ...........................................................53
Page XIII
PCISA-9102 Half-Size CPU Card
Figure 4-11: Infrared Connector Pinout Locations ..................................................54
Figure 4-12: Keyboard/Mouse Connector Location.................................................55
Figure 4-13: LCD Backlight Connector Location .....................................................56
Figure 4-14: LVDS LCD Connector Location............................................................57
Figure 4-15: Parallel Port Connector Location.........................................................58
Figure 4-16: Power Connector Location ...................................................................60
Figure 4-17: SATA Drive Connector Locations........................................................61
Figure 4-18: SDVO Connector Pinout Locations .....................................................62
Figure 4-19: RS-232 Connector Pinout Locations ...................................................64
Figure 4-20: 14-Pin Serial Port Connector Locations..............................................65
Figure 4-21: Internal USB Connector Locations ......................................................66
Figure 4-22: PCISA-9102 External Interface Connectors ........................................67
Figure 4-23: VGA Connector ......................................................................................67
Figure 4-24: RJ-45 Ethernet Connector ....................................................................69
Figure 5-1: Make sure the CPU socket retention screw is unlocked .....................75
Figure 5-2: Lock the CPU Socket Retention Screw .................................................76
Figure 5-3: IEI CF-479B-RS Cooling Kit ....................................................................76
Figure 5-4: Cooling Kit Support Bracket...................................................................77
Figure 5-5: Connect the cooling fan cable ...............................................................78
Figure 5-6: Installing a DIMM .....................................................................................79
Figure 5-7: Jumper Locations....................................................................................80
Figure 5-8: AT Power Select Jumper Location ........................................................81
Figure 5-9: CF Card Setup Jumper Location............................................................82
Figure 5-10: Clear CMOS Jumper ..............................................................................84
Figure 5-11: COM 2 Function Select Jumper Location ...........................................85
Figure 5-12: CPU Frequency Setup Jumper.............................................................86
Figure 5-13: LVDS Voltage Selection Jumper Pinout Locations............................87
Figure 5-14: LVDS Resolution Selection Jumper Pinout Locations ......................88
Figure 5-15: IDE Cable Connection ...........................................................................91
Figure 5-16: SATA Drive Cable Connection .............................................................92
Figure 5-17: SATA Power Drive Connection ............................................................93
Figure 5-18: Dual USB Cable Connection.................................................................94
Page XIV
PCISA -9102 Half-Size CPU Card
Figure 5-19: 7.1 Channel Audio Kit............................................................................95
Figure 5-20: LAN Connection.....................................................................................97
Figure 5-21: VGA Connector ......................................................................................98
Figure 5-22: USB Device Connection........................................................................99
Figure 7-1: Introduction Screen.............................................................................. 143
Figure 7-2: Available Drivers................................................................................... 143
Figure 7-3: InstallShield Wizard Preparation Screen............................................ 144
Figure 7-4: Welcome Screen ................................................................................... 144
Figure 7-5: License Agreement............................................................................... 145
Figure 7-6: Readme Information ............................................................................. 145
Figure 7-7: Restart the Computer ........................................................................... 146
Figure 7-8: Starting Install Shield Wizard Screen ................................................. 147
Figure 7-9: Preparing Setup Screen ....................................................................... 147
Figure 7-10: VGA Driver Installation Welcome Screen......................................... 148
Figure 7-11: VGA Driver License Agreement ........................................................ 148
Figure 7-12: VGA Driver Installing Notice.............................................................. 149
Figure 7-13: VGA Driver Installation Complete ..................................................... 149
Figure 7-14: Access Windows Control Panel........................................................ 150
Figure 7-15: Double Click the System Icon ........................................................... 151
Figure 7-16: Double Click the Device Manager Tab.............................................. 151
Figure 7-17: Device Manager List ........................................................................... 152
Figure 7-18: Search for Suitable Driver.................................................................. 153
Figure 7-19: Locate Driver Files.............................................................................. 153
Figure 7-20: Location Browsing Window............................................................... 154
Figure 7-21: SATA RAID Driver Installation Program........................................... 155
Figure 7-22: SATA RAID Setup Program Icon....................................................... 156
Figure 7-23: InstallShield Wizard Setup Screen.................................................... 156
Figure 7-24: Matrix Storage Manager Setup Screen............................................. 157
Figure 7-25: Matrix Storage Manager Welcome Screen ....................................... 157
Figure 7-26: Matrix Storage Manager Warning Screen ........................................ 158
Figure 7-27: Matrix Storage Manager License Agreement................................... 158
Figure 7-28: Matrix Storage Manager Readme File............................................... 159
Page XV
PCISA-9102 Half-Size CPU Card
List of Tables
Table 1-1: Model Variations..........................................................................................3
Table 1-2: Technical Specifications ............................................................................8
Table 2-1: Supported Intel® Processors...................................................................14
Table 2-2: Supported HDD Specifications ................................................................21
Table 2-3: Power Consumption .................................................................................33
Table 3-1: Package List Contents..............................................................................37
Table 3-2: Optional Items ...........................................................................................38
Table 4-1: Peripheral Interface Connectors..............................................................42
Table 4-2: Rear Panel Connectors.............................................................................43
Table 4-3: ATX Power Supply Enable Connector Pinouts ......................................44
Table 4-4: Audio Connector Pinouts .........................................................................45
Table 4-5: CF Card Socket Pinouts ...........................................................................47
Table 4-6: GPIO Connector Pinouts ..........................................................................48
Table 4-7: Fan Connector Pinouts.............................................................................49
Table 4-8: 34-pin FDD Connector Pinouts ................................................................50
Table 4-9: Front Panel Connector Pinouts ...............................................................52
Table 4-10: IDE Connector Pinouts ...........................................................................54
Table 4-11: Infrared Connector Pinouts....................................................................54
Table 4-12: Keyboard/Mouse Connector Pinouts ....................................................55
Table 4-13: LCD Backlight Connector Pinouts ........................................................56
Table 4-14: LVDS LCD Connector Pinouts ...............................................................58
Table 4-15: Parallel Port Connector Pinouts ............................................................59
Table 4-16: Power Connector Pinouts ......................................................................60
Table 4-17: SATA Drive Connector Pinouts .............................................................61
Table 4-18: SDVO Connector Pinouts .......................................................................63
Table 4-19: RS-232 Connector Pinouts .....................................................................64
Table 4-20: COM 2 Pinouts.........................................................................................65
Table 4-21: Internal USB Pinouts...............................................................................66
Page XVI
PCISA -9102 Half-Size CPU Card
Table 4-22: VGA Connector Pinouts .........................................................................68
Table 4-23: LAN1 and LAN2 Pinouts .........................................................................68
Table 4-24: RJ-45 Ethernet Connector LEDs............................................................69
Table 4-25: External USB Connector Pinouts ..........................................................69
Table 5-1: Jumpers......................................................................................................80
Table 5-2: AT Power Select Jumper Settings...........................................................81
Table 5-3: CF Card Setup Jumper Settings ..............................................................82
Table 5-4: Clear CMOS Jumper Settings ..................................................................83
Table 5-5: COM 2 Function Select Jumper Settings................................................84
Table 5-6: CPU Frequency Setup Jumper Settings .................................................85
Table 5-7: LVDS Voltage Selection Jumper Settings ..............................................87
Table 5-8: LVDS Resolution Selection Jumper Settings.........................................88
Table 5-9: IEI Provided Cables...................................................................................90
Table 6-1: BIOS Navigation Keys............................................................................ 102
Page XVII
PCISA-9102 Half-Size CPU Card
List of BIOS Menus
Menu 1: Main
................................................................................................. 103
Menu 2: Advanced No Power.................................................................................. 105
Menu 3: CPU Configuration .................................................................................... 106
Menu 4: IDE Configuration ...................................................................................... 107
Menu 5: IDE Master and IDE Slave Configuration ................................................ 109
Menu 6: IDE Master and IDE Slave Configuration ................................................ 113
Menu 7: Super IO Configuration ............................................................................. 114
Menu 8: Hardware Health Configuration ............................................................... 117
Menu 9: Remote Access Configuration [Advanced] ............................................ 120
Menu 10: USB Configuration .................................................................................. 123
Menu 11: PCI/PnP Configuration ............................................................................ 125
Menu 12: Boot........................................................................................................... 127
Menu 13: Boot Settings Configuration................................................................... 128
Menu 14: Boot Device Priority Settings ................................................................. 130
Menu 15: Removable Drives ................................................................................... 131
Menu 16: Security..................................................................................................... 132
Menu 17:Northbridge Chipset Configuration ........................................................ 133
Menu 18:Southbridge Chipset Configuration ....................................................... 136
Menu 19:Power ......................................................................................................... 137
Menu 20: Exit ............................................................................................................ 139
Page XVIII
PCISA -9102 Half-Size CPU Card
Chapter
1
1 Introduction
Page 1
PCISA-9102 Half-Size CPU Card
1.1 PCISA-9102 Overview
Figure 1-1: PCISA-9102 CPU Card
The PCISA-9102 half-size PCISA CPU card is a Socket 479 Intel® Pentium® M or
Celeron® M CPU platform. The PCISA-9102 has a maximum front side bus (FSB)
frequency of 400 MHz and contains one DDR2 SDRAM DIMM socket that supports up to
1 GB system memory.
The PCISA-9102 comes with a VGA interface and dual PCI Express (PCIe) Gigabit
Ethernet (GbE). The PCISA-9102 supports up to two SATA hard disk drives (HDD) with
maximum transfer rates of 1.5 Gb/s and up to six USB 2.0 devices.
The PCISA-9102 also has a CompactFlash® card socket for additional system storage.
Two RS-232, one parallel port and one digital input/output (DIO) port offer system
integrators more choices of peripheral devices for the targeted application. Multiple
display (VGA, LVDS and SDVO) support also adds versatility to the system enabling
system integrators and designers increased flexibility in selecting display panel options.
Page 2
PCISA -9102 Half-Size CPU Card
1.1.1 PCISA-9102 Features
Some of the PCISA-9102 features are listed below:
Complies with RoHS
Supports Socket 479 Intel® Pentium® M or Celeron® M processor
Supports a maximum FSB speed up to 400 MHz
Supports one 240-pin 1 GB (max.) 400 MHz DDR2 SDRAM DIMM
Supports one CompactFlash® Type I or Type II card
Dual PCIe GbE connectors
Supports two SATA channels with transfer rates up to 1.5 Gb/s
Supports six USB 2.0 devices
Supports CRT and 24-bit dual-channel LVDS
1.1.2 PCISA-9102 Model Variation
There are three PCISA-9102 models. They are listed below.
CPU
PCISA-9102
Socket 479 Intel® Pentium®
L2 Cache
FSB
2 MB (Max.) 400 MHz
M / Celeron® M
PCISA-9102-1GZ
1.0 GHz Intel® Celeron® M
Zero cache
400 MHz
PCISA-9102-1G512
1.0 GHz Intel® Celeron® M
512 KB
400 MHz
Table 1-1: Model Variations
Page 3
PCISA-9102 Half-Size CPU Card
1.2 PCISA-9102 Board Overview
Figure 1-2: PCISA-9102 Board Overview (Front Side)
Page 4
PCISA -9102 Half-Size CPU Card
Figure 1-3: PCISA-9102 Board Overview (Solder Side)
1.2.1 PCISA-9102 Connectors
The PCISA-9102 has the following connectors on-board:
1 x Audio connector
1 x ATX enable connector
1 x CompactFlash® card slot
1 x DDR2 DIMM socket
1 x Digital I/O connector
1 x Fan connector
1 x Floppy disk connector
1 x Front panel connector
1 x IDE Interface connector
1 x Infrared interface connector
1 x Keyboard/Mouse connector
1 x LCD backlight connector
1 x LVDS LCD connector
1 x Parallel port connector
Page 5
PCISA-9102 Half-Size CPU Card
1 x Power connector
1 x RS-232 serial port connector
1 x RS-232/422/485 serial port connector
2 x SATA connectors
1 x SDVO connector
2 x USB connectors
The PCISA-9102 has the following connectors on the board rear panel:
1 x CRT connector
2 x Ethernet connectors
2 x USB 2.0 ports
The PCISA-9102 has the following on-board jumpers:
CF card setup
Clear CMOS
CPU frequency selection
COM 2 function selection
LCD voltage selection
LVDS panel resolution selection
The location of these connectors on the motherboard can be seen in Figure 1-1. These
connectors are fully described in Chapter 3.
1.2.2 Technical Specifications
PCISA-9102 technical specifications are listed in Table 1-2. Detailed descriptions of each
specification can be found in Chapter 2.
SPECIFICATION
CPUs Supported
PCISA-9102
Socket 479 Intel® Pentium® M
Socket 479 Intel® Celeron® M
On-board 1 GHz Intel® Celeron® M with 512 KB/zero cache
FSB
Page 6
400 MHz
PCISA -9102 Half-Size CPU Card
Chipsets
Northbridge: Intel® 910GMLE
Southbridge: Intel® ICH6-M
Graphics Support
Display
Intel® Graphics Media Accelerator (GMA) 900
CRT
LVDS: Dual-channel 24-bit LVDS
Memory
One 240-pin 400 MHz single-channel DDR2 SDRAM DIMM
(system max. 1 GB)
Super I/O
Winbond W83627EHG
Serial ATA (SATA)
Two SATA connectors with 1.5 Gb/s transfer rates
HDD Interface
One IDE channel supports two Ultra ATA 100/66/33 devices
FDD Interface
One FDD connector
SSD
One CompactFlash® Type I or Type II slot
USB Interfaces
Six USB 2.0 devices supported (four internal and two
external)
Serial Ports
One RS-232
One RS-232/422/485
Keyboard/Mouse
One keyboard/mouse connector (6-pin header)
One IrDA connector through the Winbond W83627EHG super
Infrared
I/O. supports:
Serial Infrared (SIR)
Amplitude Shift Keyed IR (ASKIR)
Digital I/O
8-bit digital I/O, 4-bit input / 4-bit output by super I/O
Audio
7.1 channel HD audio via AC-KIT883HD audio kit or
5.1 channel AC’97 audio via AC-KIT08R audio kit
Ethernet
Dual Broadcom BCM5787M PCIe GbE controllers
BIOS
AMI BIOS Label
Page 7
PCISA-9102 Half-Size CPU Card
Power
AT and ATX power
Power Consumption
5V @ 2.51 A, 12V @ 2.15 A, [email protected], [email protected]
(1.80 GHz Intel® Pentium® M 745 with a 400 MHz FSB and a
1 GB DDR2 DIMM)
Operating Temperature
Minimum: 0ºC (32°F)
Maximum: 60°C (140°F)
Humidity
5%~95% non condensing
Physical Dimensions
185 mm x 127.6 mm (width x length)
Weight (GW/NW)
1000 g / 230 g
Table 1-2: Technical Specifications
Page 8
PCISA -9102 Half-Size CPU Card
Chapter
2
2 Detailed Specifications
Page 9
PCISA-9102 Half-Size CPU Card
2.1 Overview
This chapter describes the specifications and on-board features of the PCISA-9102 in
detail.
2.2 Dimensions
2.2.1 Board Dimensions
The dimensions of the board are listed below:
Page 10
Length:
185.0 mm
Width:
127.6 mm
PCISA -9102 Half-Size CPU Card
Figure 2-1: PCISA-9102 Dimensions (mm)
Page 11
PCISA-9102 Half-Size CPU Card
2.2.2 External Interface Panel Dimensions
External peripheral interface connector panel dimensions are shown in Figure 2-2.
Figure 2-2: External Interface Panel Dimensions (mm)
2.3 Data Flow
The PCISA-9102 motherboard comes with an Intel® 910GMLE GMCH and an Intel®
ICH6-M I/O Controller Hub. Figure 2-3 shows the data flow between the system chipset,
the CPU and other components installed on the motherboard.
Page 12
PCISA -9102 Half-Size CPU Card
Figure 2-3: Data Flow Block Diagram
Page 13
PCISA-9102 Half-Size CPU Card
2.4 Compatible Processors
Table 2-1 lists the Intel® processors supported on the PCISA-9102. All the processors in
Table 2-1 are 90nm Socket 479 processors.
Processor
Max. CPU Speed
FSB Speed
Max. Cache Size
Intel® Pentium® M
2.10 GHz
400 MHz
2 MB
Intel® Celeron® M
1.70 GHz
400 MHz
1 MB
Table 2-1: Supported Intel® Processors
2.5 Intel® 910GMLE Graphics and Memory Controller Hub
2.5.1 Intel® 910GMLE Overview
The Intel® 910GMLE GMCH has the Intel® Graphics Media Accelerator 900 (Intel® GMA
900) to support integrated graphics. The integrated graphics and memory controller hub
(GMCH) facilitates the flow of information primarily between the following four interfaces:
Front Side Bus (FSB)
System Memory Interface
Graphics Interface
Direct Media Interface (DMI)
2.5.2 Intel® 910GMLE Front Side Bus (FSB) Support
The Intel® 910GMLE GMCH supports processors with a 400 MHz FSB. The Socket 479,
Intel® 910GMLE GMCH and the FSB are shown in Figure 2-4.
Page 14
PCISA -9102 Half-Size CPU Card
Figure 2-4: Front Side Bus (FSB)
2.5.3 Intel® 910GMLE Memory Support
WARNING:
Only DDR2 memory module can be installed on the PCISA-9102. Do
not install DDR memory modules. If a DDR memory module is installed
on the PCISA-9102, the PCISA-9102 may be irreparably damaged.
The Intel® 910GMLE GMCH on the PCISA-9102 supports one 240-pin DDR2 DIMM with
the following features:
One 240-pin DIMM
DDR2 only (DO NOT install a DDR DIMM)
Single-channel
Capacities of 256 MB, 512 MB or 1 GB
Transfer speeds of 400 MHz
64-bit wide channel
The memory sockets are shown in Figure 2-5.
Page 15
PCISA-9102 Half-Size CPU Card
Figure 2-5: 240-pin DDR2 DIMM Socket
2.5.4 Intel® 910GMLE Integrated Graphics
The Intel® 910GMLE GMCH has a mobile Intel® Graphics Media Accelerator 900
integrated graphics engine that supports the following display devices:
Analog CRT
LVDS
SDVO
Figure 2-6: Integrated Graphics Interfaces
Page 16
PCISA -9102 Half-Size CPU Card
2.5.4.1 Intel® 910GMLE Analog CRT Support
A DB-15 VGA connector on the external peripheral interface connector panel is interfaced
to the Intel® 910GMLE graphics engine. The Intel® 910GMLE internal graphics engine
supports:
Max DAC frequency up to 400 MHz
24-bit RAMDAC
Analog CRT monitors up to QXGA (2048 x 1536).
2.5.4.2 Intel® 910GMLE LVDS Support
A 30-pin LVDS crimp connector is interfaced to the Intel® 910GMLE graphics engine. The
Intel® 910GMLE internal graphics engine supports LVDS displays with the following
features:
Compliant with ANSI/TIA/EIA -644-2001 spec
Integrated dual channel LVDS interface supported on Display Pipe B only
Supports 25 MHz to 112 MHz single/dual channel LVDS interface
o
o
Single channel LVDS interface support: 1 x 18 bpp
Dual channels LVDS interface support: 2 x 18 bpp
TFT panel type supported
Maximum Panel size supported up to UXGA
Maximum Wide panel size supported up to WUXGA
Ambient Light Sense support for automatic backlight brightness adjustments
Intel Display Power Savings Technology 2.0 support
Supports Single pipe simultaneous display with the CRT DAC and the LVDS
ports under the following conditions:
o
Timings must match for both display
Panel Fitting. Panning, and Center mode supported
Spatial Dithering support to emulate up to 16 million colors for 18bpp TFT
panels
Spread spectrum clocking (SSC) supported
o
Supports down and center SSC via an SSC clock from an external SSC
clock chip.
Page 17
PCISA-9102 Half-Size CPU Card
o
Supports down spread of – 2.5% or center spread of ± -1.25% in
reference 30-50 kHz modulation rate
SSC must be disabled for LVDS port and CRT DAC single pipe simultaneous
display mode.
Panel Power Sequencing support
o
Power down state can be either zero volt or high impedance
Integrated PWM interface for LCD Backlight Inverter Control
Up to UXGA monitors with a maximum resolution of 1600 x 1200
24-bit 25 MHz to 112 MHz single-channel or dual-channel LVDS screens
CPIS 1.5 compliant LVDS screens
2.5.4.3 Intel® 910GMLE SDVO Support
The Intel® 910GMLE internal graphics engine has the following SDVO output features:
Two SDVO ports are supported
Supports a variety display devices such as DVI, LVDS, etc.
Compliant with DVO specification 1.0 when combined with a DVI compliant
external device and connector.
Data sourced from either display Pipe A or Pipe B
Supports single pipe simultaneous display with the DAC or LVDS ports
Timings must match for both display
Single pipe not supported with SSC on LVDS port
Each SDVO Port support display pixel rates up to 200 MP/s (600 MB/s)
Fast point-to-point GMBUS is provided for SDVO device control
Supports Hot Plug and Display
Support for HDCP SDVO devices
2.5.5 Intel® 910GMLE Direct Management Interface (DMI)
The Direct Media Interface (DMI) is the communication bus between the Intel® 910GMLE
GMCH and the ICH6-M I/O controller hub (ICH). The DMI is a high-speed interface that
integrates advanced priority-based servicing and allows for concurrent traffic and true
isochronous transfer capabilities. The DMI is shown in Figure 2-7.
Page 18
PCISA -9102 Half-Size CPU Card
Figure 2-7: DMI Chip-to-Chip Connection
Features of the Intel® 910GMLE DMI are listed below:
2GB/s (1GB/s in each direction) bus speed
Configurable as x2 or x4 DMI lanes
32-bit downstream address
2.6 Intel® ICH6-M I/O Controller Hub
2.6.1 Intel® ICH6-M Overview
The Intel® ICH6-M Southbridge chipset is connected to the Intel® 915GM Northbridge
GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the
Intel® ICH6-M are listed below.
Complies with PCI Express Base Specification, Revision 1.0a
Complies with PCI Local Bus Specification, Revision 2.3 and supports 33MHz
PCI operations
Supports ACPI Power Management Logic
Contains:
o
o
o
Enhanced DMA controller
Interrupt controller
Timer functions
Integrated SATA host controller with DMA operations interfaced to two SATA
Page 19
PCISA-9102 Half-Size CPU Card
connectors on the PCISA-9102
Integrated IDE controller supports Ultra ATA 100/66/33
Supports the four USB 2.0 devices on the PCISA-9102 with four UHCI
controllers and one EHCI controller
Complies with System Management Bus (SMBus) Specification, Version 2.0
Supports Audio Codec ’97 (AC’97) Revision 2.3
Supports Intel® High Definition Audio
Contains Low Pin Count (LPC) interface
Supports Firmware Hub (FWH) interface
2.6.2 Intel® ICH6-M Audio Codec ’97 Controller
The Audio Codec ’97 (AC’97) controller integrated into the ICH6-M complies with AC’97
Component Specification, Version 2.3. The AC’97 controller is connected to the onboard
audio connector. The audio connector is connected to an optional 5.1 channel or 7.1
channel audio kit with an embedded AC’97 audio codec. The AC’97 controller supports up
to six PCM audio output channels. Complete surround sound requires six-channel audio
consisting of:
Front left
Front right
Back left
Back right
Center
Subwoofer
Page 20
PCISA -9102 Half-Size CPU Card
Figure 2-8: Audio Connector
2.6.3 Intel® ICH6-M IDE Interface
The integrated IDE interface on the ICH6-M supports two IDE hard disks and ATAPI
devices. PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100 MB/s. The
integrated IDE interface is able to support the following IDE HDDs:
Ultra ATA/100, with data transfer rates up to 100 MB/s
Ultra ATA/66, with data transfer rates up to 66 MB/s
Ultra ATA/33, with data transfer rates up to 33 MB/s
Specification
Ultra ATA/100
Ultra ATA/66
Ultra ATA/33
IDE devices
2
2
2
PIO Mode
0–4
0–4
0–4
PIO Max Transfer Rate
16.6 MB/s
16.6 MB/s
16.6 MB/s
DMA/UDMA designation
UDMA 3 - 4
UDMA 3 – 4
UDMA 2
DMA/UDMA Max
100 MB/s
66 MB/s
33 MB/s
5V
5V
5V
Transfer
Controller Interface
Table 2-2: Supported HDD Specifications
Page 21
PCISA-9102 Half-Size CPU Card
2.6.4 Intel® ICH6-M Low Pin Count (LPC) Interface
The ICH6-M LPC interface complies with the LPC 1.1 specifications. The LPC bus from
the ICH6-M is connected to the following components:
BIOS chipset
Super I/O chipset
For more detailed information please refer to Section 2.8.
2.6.5 Intel® ICH6-M PCI Interface
The PCI bus on the ICH6-M is compliant with the PCI Revision 2.3 implementation. Some
of the features of the PCI interface are listed below.
PCI Revision 2.3 compliant
33 MHz
5V tolerant PCI signals (except PME#)
Integrated PCI arbiter supports up to seven PCI bus masters
2.6.5.1 Winbond W83628 PCI-to-ISA Bridge
The ICH6-M is interfaced to a Winbond W83628 PCI-to-ISA bridge through the PCI bus.
The Winbond W83628 PCI-to-ISA bridge is then connected to an ISA edge connector on
the bottom of the PCISA-9102 thereby enabling legacy ISA card expansion on the
backplane. The PCI to ISA bridge is shown in Figure 2-9.
Page 22
PCISA -9102 Half-Size CPU Card
Figure 2-9: PCI-to-ISA Bridge
Some of the features of the Winbond PCI-to-ISA Bridge are listed below:
Full ISA bus support including ISA masters
5 V ISA and 3.3 V PCI interfaces
Supports three ISA compatible slots without buffering
External BIOS ROM address decode output
2.6.6 Intel® ICH6-M PCIe x1 Bus
The Intel® ICH6-M GMCH has four PCIe x1 lanes. Two of the four PCIe lanes are
implemented on the PCISA-9102, including:
Two PCIe x1 lanes are connected to two Broadcom BCM5787M GbE
controllers
For more detailed information, please refer to Section 2.7.
2.6.7 Intel® ICH6-M Real Time Clock
256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock
(RTC) integrated into the ICH6-M. The RTC operates on a 3 V battery and 32.768 KHz
crystal. The RTC keeps track of the time and stores system data even when the system is
turned off.
Page 23
PCISA-9102 Half-Size CPU Card
2.6.8 Intel® ICH6-M SATA Controller
The integrated SATA controller on the ICH6-M supports two SATA drives on the
PCISA-9102 with independent DMA operations. SATA controller specifications are listed
below.
Supports two SATA drives
Supports 1.5 Gb/s data transfer speeds
Supports Serial ATA Specification, Revision 1.0a
Figure 2-10: SATA Drive Connectors
2.6.9 Intel® ICH6-M USB Controller
Up to eight high-speed, full-speed or low-speed USB devices are supported by the
ICH6-M on the PCISA-9102. High-speed USB 2.0, with data transfers of up to 480 MB/s,
is enabled with the ICH6-M integrated Enhanced Host Controller Interface (EHCI)
compliant host controller. USB full-speed and low-speed signaling is supported by the
ICH6-M integrated Universal Host Controller Interface (UHCI) controllers.
Six of the eight USB ports implemented on the PCISA-9102 are connected to two internal
connectors and two external connectors. See Figure 2-11.
Page 24
PCISA -9102 Half-Size CPU Card
Figure 2-11: Onboard USB Implementation
2.7 PCIe Bus Components
2.7.1 PCIe Bus Overview
The PCIe bus is connected to components listed below:
Two PCIe x1 lanes are connected to two Broadcom PCIe GbE connectors
2.7.2 Broadcom BCM5787M PCIe GbE Controller
Two RJ-45 Ethernet LAN connectors are interfaced directly to two Broadcom BCM5787M
PCIe GbE controllers. The Broadcom BCM5787M PCIe GbE controller combines a
triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed
Ethernet transceiver and interfaced to the Intel® ICH6-M Southbridge through a PCIe x1
lane. The Broadcom BCM5787M GbE controllers are shown in Figure 2-12 below.
Page 25
PCISA-9102 Half-Size CPU Card
Figure 2-12: Broadcom BCM5787M PCIe GbE Controllers
Some of the BCM5787 controller features are listed below:
Integrated 10/100/1000BASE-T transceiver
Automatic MDI crossover function
PCIe v1.0a
10/100/1000BASE-T full/half-duplex MAC
Wake on LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (802.3z,
clause 30)
Serial EEPROM or serial flash support
JTAG support
2.8 LPC Bus Components
2.8.1 LPC Bus Overview
The LPC bus is connected to components listed below:
BIOS chipset
Super I/O chipset
Page 26
PCISA -9102 Half-Size CPU Card
2.8.2 BIOS Chipset
The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset. Some of the
BIOS features are listed below:
AMI Flash BIOS
SMIBIOS (DMI) compliant
Console redirection function support
PXE (Pre-boot Execution Environment) support
USB booting support
The BIOS chipset is shown in Figure 2-13 below.
Figure 2-13: BIOS Chipset
2.8.3 Winbond W83627EHG Super I/O Chipset
The Winbond W83627EHG Super I/O chipset is connected to the ICH6-M Southbridge
through the LPC bus. Winbond W83627EHG Super I/O chipset is shown in Figure 2-14
below.
Page 27
PCISA-9102 Half-Size CPU Card
Figure 2-14: Winbond W83627EHG Super I/O
The Winbond W83627EHG is an LPC interface-based Super I/O device that comes with
Environment Controller integration, floppy disk controller, UART controller and IR
controller. Some of the features of the Winbond W83697EHG chipset are listed below:
LPC Spec. 1.01 compliant
LDRQ# (LPC DMA) and SERIRQ (serial IRQ) supported
Hardware monitor functions integrated
Microsoft PC98/PC99 Hardware Design Guide compliant
ACPI DPM (Device Power Management) supported
Some of the Super I/O features are described in more detail below:
2.8.3.1 Super I/O LPC Interface
The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specification
Rev. 1.01. The LPC interface supports both LDRQ# and SERIRQ protocols as well as PCI
PME# interfaces.
Page 28
PCISA -9102 Half-Size CPU Card
2.8.3.2 Super I/O UART Controller
There are two high-speed 16550 compatible UART controllers integrated onto the Super
I/O chipset. Both controllers have 16-byte send/receive FIFO. Some of the features of the
UART controllers are listed below:
MIDI compatible
Fully programmable serial-interface characteristics:
o
o
o
5, 6, 7, or 8-bit characters
Even, odd or no parity bit generation/detection
1, 1.5 or 2 stop bits generation
Internal diagnostic capabilities:
o
o
Loop-back control for communications link fault isolation
Break, parity, overrun, framing error stimulation
Programmable baud generator allows division of 1.8461 MHz and 24 MHz by
1 to (216 – 1)
Maximum baud rate up to 921 kbps for 14.769 MHz and 1.5 Mbps for 24 MHz
2.8.3.3 Super I/O Infrared
The onboard Super I/O supports the following infrared specifications:
IrDA version 1.0 SIR protocol with a maximum baud rate up to 115.2 Kbps
The IR controller on the super I/O is interfaced through the onboard IrDA pin-header on
the PCISA-9102.
2.8.3.4 Super I/O Hardware Monitor Functions
The Super I/O Hardware Monitor monitors internal voltages, system temperature and the
cooling fan speed. All the monitored environmental parameters can be read from the BIOS
Hardware Health Configuration menu.
2.8.3.5 Super I/O Parallel Port
The Super I/O parallel port (LPT) is compatible with the following LPT specifications.
Page 29
PCISA-9102 Half-Size CPU Card
IBM parallel port compatible
PS/2 compatible bi-directional parallel port
Enhanced Parallel Port (EPP) mode supported. Compatible with IEEE 1284
specifications
Extended Parallel Port (EPP) mode supported. Compatible with IEEE 1284
specifications
Enhanced printer port back-drive current protection
The parallel port controller is connected to an onboard LPT connector.
2.8.3.6 Super I/O Floppy Disk Drive (FDD) Controller
The Super I/O FDD controller is compatible with the following specifications.
IBM PC AT disk drive compatible
Variable write pre-compensation with track selectable capability
Vertical recording format supported
DMA logic enabled
16-byte data FIFOs
Overrun and under run conditions detected
Built-in address mark detection circuitry to simplify the read electronics
FDD anti-virus functions with software write protect and FDD write enable
signal
Supports 3.5-inch or 5.25-inch FDD
Compatible with industry standard 82077
Supported capacities:
o
o
o
o
o
360 K
720 K
1.2 M
1.44 M
2.88 M
Supported transfer rates
o
o
o
o
Page 30
250 Kbps
300 Kbps
500 Kbps
1 Mbps
PCISA -9102 Half-Size CPU Card
o
2 Mbps
3-mode FDD and Win95/98 driver supported
The FDD controller is interfaced to a FDD pin-header connector on the PCISA-9102.
2.8.3.7 Super I/O Keyboard and Mouse Controller
The Super I/O keyboard and mouse controller is compatible with the following
specifications.
8042 compatible
Asynchronous access to two data registers and one status register
Compatible with 8042 software
PS/2 mouse supported
Port 92 supported
Interrupt and polling modes supported
Fast Gate A20 and Hardware Keyboard Reset
8-bit timer/counter
The keyboard and mouse controller is interfaced to a keyboard and mouse connected to
the PCISA-9102 through the onboard connector.
2.8.3.8 Super I/O GPIO Ports
The Super I/O has 22 programmable GPIO ports.
2.8.3.9 Super I/O Fan Speed and Fan Control
The super I/O can both monitor and control the fan speed. The super I/O is interfaced to
the fan on the backplane through the board-to-board connectors.
2.9 Environmental and Power Specifications
2.9.1 System Monitoring
Three thermal inputs on the PCISA-9102 Super I/O Enhanced Hardware Monitor monitor
the following temperatures:
Page 31
PCISA-9102 Half-Size CPU Card
CPU temperature
PWM temperature
System temperature
Eight voltage inputs on the PCISA-9102 Super I/O Enhanced Hardware Monitor monitor
the following voltages:
+1.5V
+1.8V
+3.30V
+5.00V
+12.0V
VBAT
The PCISA-9102 Super I/O Enhanced Hardware Monitor also monitors the following fan
speed:
CPU Fan speed
The values for the above environmental parameters are all recorded in the BIOS
Hardware Health Configuration menu.
2.9.2 Operating Temperature and Temperature Control
The maximum and minimum operating temperatures for the PCISA-9102 are listed below.
Minimum Operating Temperature: 0ºC (32°F)
Maximum Operating Temperature: 60°C (140°F)
A cooling fan and heat sink must be installed on the CPU. Thermal paste must be
smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks
are also mounted on the GMCH and ICH chipsets to ensure the operating temperature of
these chips remain low.
Page 32
PCISA -9102 Half-Size CPU Card
2.9.3 Power Consumption
Table 2-3 shows the power consumption parameters for the PCISA-9102 running with a
1.80 GHz Intel® Pentium® M 745 with a 400 MHz FSB and a 400 MHz 1 GB DDR2 DIMM,
Voltage
Current
+5 V
2.51 A
+12 V
2.15 A
+3.3 V
1.27 A
5 V standby
0.3 A
Table 2-3: Power Consumption
Page 33
PCISA-9102 Half-Size CPU Card
Chapter
3
3 Unpacking
Page 34
PCISA -9102 Half-Size CPU Card
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
PCISA-9102 may result in permanent damage to the PCISA-9102 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the PCISA-9102. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the PCISA-9102, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the PCISA-9102, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
PCISA-9102.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
3.2 Unpacking
3.2.1 Unpacking Precautions
When the PCISA-9102 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 3.1.
Make sure the packing box is facing upwards so the PCISA-9102 does not fall
out of the box.
Make sure all the components shown in Section 3.3 are present.
Page 35
PCISA-9102 Half-Size CPU Card
3.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the PCISA-9102 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
3.3.1 Package Contents
The PCISA-9102 is shipped with the following components:
Quantity
Item and Part Number
1
PCISA-9102 CPU card
1
Parallel port and RS-232 cable
(P/N: 19800-000027-RS)
1
IDE cable
(P/N: 32200-000052-RS)
2
SATA cables
(P/N: 32000-062800-RS)
1
SATA power cable
(P/N: 32100-088600-RS)
Page 36
Image
PCISA -9102 Half-Size CPU Card
1
Mini jumper pack
1
Quick Installation Guide
1
Dual port USB cable
(P/N: CB-USB02-RS)
1
Utility CD
Table 3-1: Package List Contents
3.3.2 Optional Items
NOTE:
The items listed in this section are optional items that must be ordered
separately. Please contact your PCISA-9102 vendor, distributor or
reseller for more information or, contact IEI directly by sending an email
to [email protected]
The following optional items are available for the PCISA-9102.
Quantity
1
Item and Part Number
Image
7.1 Channel HD audio kit with Realtek
ALC883
(P/N: AC-KIT883HD-R10)
Page 37
PCISA-9102 Half-Size CPU Card
Quantity
1
Item and Part Number
5.1 Channel AC’97 audio kit with Realtek
ALC655
(P/N: AC-KIT08R-R10)
1
CPU Cooler
(P/N: CF-479B-RS)
1
FDD cable
(P/N: 32200-000058-RS)
1
KB/MS cable with bracket
(P/N: 19800-000075-RS)
1
RS-232/422/485 cable
(P/N: 32200-000077-RS)
Table 3-2: Optional Items
Page 38
Image
PCISA -9102 Half-Size CPU Card
Chapter
4
4 Connectors and
Jumpers
Page 39
PCISA-9102 Half-Size CPU Card
4.1 Peripheral Interface Connectors
Section 4.1.1 shows peripheral interface connector locations. Section 4.1.2 lists all the
peripheral interface connectors seen in Section 4.1.1.
4.1.1 PCISA-9102 Layout
Figure 4-1 shows the on-board peripheral connectors, backplane peripheral connectors
and on-board jumpers.
Figure 4-1: Connector and Jumper Locations (Front Side)
Page 40
PCISA -9102 Half-Size CPU Card
Figure 4-2: Connector and Jumper Locations (Solder Side)
4.1.2 Peripheral Interface Connectors
Table 4-1 shows a list of the peripheral interface connectors on the PCISA-9102. Detailed
descriptions of these connectors can be found in Section 4.2.
Connector
Type
Label
ATX enable connector
3-pin wafer
ATXCTL1
Audio connector
10-pin header
J_AUDIO1
CompactFlash® card slot
50-pin slot
CF1
DDR2 DIMM socket
240-pin slot
DDRIIA1
Digital Input/Output connector
10-pin header
DIO1
Fan connector, CPU
4-pin wafer
CPU_FAN1
FDD connector
34-pin header
FDD1
Page 41
PCISA-9102 Half-Size CPU Card
Front panel connector
8-pin header
F_PANEL1
IDE Interface connector
40-pin box header
IDE1
Infrared interface connector
5-pin header
IR1
Keyboard connector
6-pin wafer
KB_MS1
LCD backlight connector
5-pin wafer
INVERTER1
LVDS LCD connector
30-pin crimp
LVDS1
Parallel port connector
26-pin header
LPT1
Power connector
4-pin connector
ATXPWR1
SATA drive connector (1)
7-pin SATA connector
SATA1
SATA drive connector (2)
7-pin SATA connector
SATA2
SDVO connector
47-pin connector
CN1
Serial port connector
10-pin header
COM1
Serial port connector
14-pin header
COM2
USB connector (1)
8-pin header
USB01
USB connector (2)
8-pin header
USB23
Table 4-1: Peripheral Interface Connectors
4.1.3 Rear Panel Connectors
Table 4-2 lists the rear panel connectors on the PCISA-9102. Detailed descriptions of
these connectors can be found in Section 4.3.
Connector
Type
Label
CRT connector
15-pin female connector
VGA1
Ethernet connector (1)
RJ-45 connector
LAN1
Ethernet connector (2)
RJ-45 connector
LAN2
Page 42
PCISA -9102 Half-Size CPU Card
USB 2.0 port (1)
USB port connector
USB_C4
USB 2.0 port (2)
USB port connector
USB_C5
Table 4-2: Rear Panel Connectors
4.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the PCISA-9102.
4.2.1 ATX Power Supply Enable Connector
CN Label:
ATXCTL1
CN Type:
3-pin wafer (1x3)
CN Location:
See Figure 4-3
CN Pinouts:
See Table 4-3
The ATX power supply enable connector enables the PCISA-9102 to be connected to an
ATX power supply.
Figure 4-3: ATX Power Supply Enable Connector Location
Page 43
PCISA-9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
1
GND
2
PS-ON
3
+5V Standby
Table 4-3: ATX Power Supply Enable Connector Pinouts
4.2.2 Audio Connector
CN Label:
J_AUDIO1
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-4
CN Pinouts:
See Table 4-4
The audio connector connects to the optional audio kit to provide 7.1 channels HD audio
or 5.1 channels AC’97 audio to the system.
Figure 4-4: Audio Connector Location
Page 44
PCISA -9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
SYNC
2
BITCLK
3
SDOUT
4
PCBEEP
5
SDIN
6
RST#
7
VCC
8
GND
9
+12V
Table 4-4: Audio Connector Pinouts
4.2.3 CompactFlash® Socket
CN Label:
CF1 (solder side)
CN Type:
50-pin slot (2x25)
CN Location:
See Figure 4-5
CN Pinouts:
See Table 4-5
A CF Type I or Type II memory card is inserted to the CF socket on the solder side of the
PCISA-9102.
Page 45
PCISA-9102 Half-Size CPU Card
Figure 4-5: CF Card Socket Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GROUND
26
VCC-IN CHECK1
2
DATA 3
27
DATA 11
3
DATA 4
28
DATA 12
4
DATA 5
29
DATA 13
5
DATA 6
30
DATA 14
6
DATA 7
31
DATA 15
Page 46
PCISA -9102 Half-Size CPU Card
7
HDC_CS0#
32
HDC_CS1
8
N/C
33
N/C
9
GROUND
34
IOR#
10
N/C
35
IOW#
11
N/C
36
VCC_COM
12
N/C
37
IRQ15
13
VCC_COM
38
VCC_COM
14
N/C
39
CSEL
15
N/C
40
N/C
16
N/C
41
HDD_RESET
17
N/C
42
IORDY
18
SA2
43
SDREQ
19
SA1
44
SDACK#
20
SA0
45
HDD_ACTIVE#
21
DATA 0
46
66DET
22
DATA 1
47
DATA 8
23
DATA 2
48
DATA 9
24
N/C
49
DATA 10
25
VCC-IN CHECK2
50
GROUND
Table 4-5: CF Card Socket Pinouts
4.2.4 Digital Input/Output Connector
CN Label:
DIO1
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-6
CN Pinouts:
See Table 4-6
The DIO connector is managed through a Super I/O chip. The DIO connector pins are
user programmable. The digital IO port of PCISA-9102 is 5 V CMOS level.
Page 47
PCISA-9102 Half-Size CPU Card
Figure 4-6: GPIO Connector Location
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
GND
2
VCC
3
OUTPUT 3
4
OUTPUT 2
5
OUTPUT 1
6
OUTPUT 0
7
INPUT 3
8
INPUT 2
9
INPUT 1
10
INPUT 0
Table 4-6: GPIO Connector Pinouts
4.2.5 Fan Connector
CN Label:
CPU_FAN1
CN Type:
4-pin wafer connector (1x4)
CN Location:
See Figure 4-7
CN Pinouts:
See Table 4-7
The cooling fan connector provides a 12V, 500mA current to a CPU cooling fan. The
connector has a "rotation" pin to get rotation signals from fans and notify the system so the
system BIOS can recognize the fan speed. Please note that only specified fans can issue
the rotation signals.
Page 48
PCISA -9102 Half-Size CPU Card
Figure 4-7: Fan Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
+12VCC
3
Rotation Signal
4
Control
Table 4-7: Fan Connector Pinouts
4.2.6 Floppy Disk Connector (34-pin)
CN Label:
FDD1
CN Type:
34-pin header (2x17)
CN Location:
See Figure 4-8
CN Pinouts:
See Table 4-8
The floppy disk connector is connected to a floppy disk drive.
Page 49
PCISA-9102 Half-Size CPU Card
Figure 4-8: 34-pin FDD Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
DRVDE0
3
GND
4
N/C
5
GND
6
N/C
7
GND
8
INDEX#
9
GND
10
MTR0#
11
GND
12
N/C
13
GND
14
DR0#
15
GND
16
N/C
17
GND
18
DIR0#
19
GND
20
STEP#
21
GND
22
WDATA#
23
GND
24
WGATE#
25
GND
26
TRACK 0#
27
GND
28
WRPRO#
29
GND
30
READ DATA#
31
GND
32
HDSEL##
33
N/C
34
DSKCH#
Table 4-8: 34-pin FDD Connector Pinouts
Page 50
PCISA -9102 Half-Size CPU Card
4.2.7 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
8-pin header (2x4)
CN Location:
See Figure 4-9
CN Pinouts:
See Table 4-9
The front panel connector connects to several external switches and indicators to monitor
and control the motherboard. These indicators and switches include:
Power LED
Power button
Reset button
HDD LED
Figure 4-9: Front Panel Connector Location
Page 51
PCISA-9102 Half-Size CPU Card
FUNCTION
PIN
DESCRIPTION
FUNCTION
PIN
DESCRIPTION
Power
1
PWR_BTN+
Power
2
PWR_LED+
Button
3
PWR_BTN-
LED
4
PWR_LED-
HDD LED
5
HDD_LED+
Reset
6
RESET+
7
HDD_LED-
8
RESET-
Table 4-9: Front Panel Connector Pinouts
4.2.8 IDE Connector
CN Label:
IDE1
CN Type:
40-pin box header (2x20)
CN Location:
See Figure 4-10
CN Pinouts:
See Table 4-10
One primary 40-pin IDE device connector on the PCISA-9102 motherboard supports
connectivity to ATA 100/66/33 IDE devices with data transfer rates up to 100 MB/s.
Page 52
PCISA -9102 Half-Size CPU Card
Figure 4-10: IDE Device Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
N/C
21
IDE DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
IDE CHRDY
28
BALE – DEFAULT
29
IDE DACK
30
GND
31
INTERRUPT
32
N/C
33
SA1
34
PDIAG#
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
Page 53
PCISA-9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
39
HDD ACTIVE#
PIN NO.
40
DESCRIPTION
GND
Table 4-10: IDE Connector Pinouts
4.2.9 Infrared Interface Connector
CN Label:
IR1
CN Type:
5-pin header (1x5)
CN Location:
See Figure 4-11
CN Pinouts:
See Table 4-11
The infrared interface connector supports both Serial Infrared (SIR) and Amplitude Shift
Key Infrared (ASKIR) interfaces.
Figure 4-11: Infrared Connector Pinout Locations
PIN NO.
DESCRIPTION
1
VCC
2
NC
3
IR-RX
4
GND
5
IR-TX
Table 4-11: Infrared Connector Pinouts
Page 54
PCISA -9102 Half-Size CPU Card
4.2.10 Keyboard/Mouse Connector
CN Label:
KB_MS1
CN Type:
6-pin header (1x6)
CN Location:
See Figure 4-12
CN Pinouts:
See Table 4-12
The keyboard/mouse connector can be connected to a standard PS/2 cable or PS/2 Y
cable to add keyboard and mouse functionality to the system.
Figure 4-12: Keyboard/Mouse Connector Location
PIN NO.
DESCRIPTION
1
VCC
2
MS DATA
3
MS CLK
4
KB DATA
5
KB CLK
6
KB GROUND
Table 4-12: Keyboard/Mouse Connector Pinouts
Page 55
PCISA-9102 Half-Size CPU Card
4.2.11 LCD Backlight Connector
CN Label:
INVERTER1
CN Type:
5-pin wafer connector (1x5)
CN Location:
See Figure 4-13
CN Pinouts:
See Table 4-13
The LCD backlight connector is for the LCD inverter connection.
Figure 4-13: LCD Backlight Connector Location
PIN NO.
DESCRIPTION
1
BRIGHTNESS
2
GND1
3
12V
4
GND2
5
BL_EN
Table 4-13: LCD Backlight Connector Pinouts
Page 56
PCISA -9102 Half-Size CPU Card
4.2.12 LVDS LCD connector
CN Label:
LVDS1
CN Type:
30-pin crimp connector (2x15)
CN Location:
See Figure 4-14
CN Pinouts:
See Table 4-14
The connector supports one or two channel 24-bit LVDS panel.
Figure 4-14: LVDS LCD Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND1
2
GND2
3
A_Y0
4
A_Y0#
5
A_Y1
6
A_Y1#
7
A_Y2
8
A_Y2#
9
A_CK
10
A_CK#
11
A_Y3
12
A_Y3#
13
GND3
14
GND4
15
B_Y0
16
B_Y0#
17
B_Y1
18
B_Y1#
19
B_Y2
20
B_Y2#
21
B_CK
22
B_CK#
Page 57
PCISA-9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
23
B_Y3
24
B_Y3#
25
GND5
26
GND6
27
VCC_LCD
28
VCC_LCD
29
VCC_LCD
30
VCC_LCD
Table 4-14: LVDS LCD Connector Pinouts
4.2.13 Parallel Port Connector
CN Label:
LPT1
CN Type:
26-pin header (2x13)
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-15
The 26-pin parallel port connector connects to a parallel port connector interface or some
other parallel port device such as a printer.
Figure 4-15: Parallel Port Connector Location
Page 58
PCISA -9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
STROBE#
14
AUTO FORM FEED #
2
DATA0
15
ERROR#
3
DATA1
16
INITIALIZE#
4
DATA2
17
PRINTER SELECT LN#
5
DATA3
18
GND
6
DATA4
19
GND
7
DATA5
20
GND
8
DATA6
21
GND
9
DATA7
22
GND
10
ACKNOWLEDGE#
23
GND
11
BUSY
24
GND
12
PAPER EMPTY
25
GND
13
PRINTER SELECT
Table 4-15: Parallel Port Connector Pinouts
4.2.14 Power Connector
CN Label:
ATXPWR1
CN Type:
4-pin connector (1x4)
CN Location:
See Figure 4-16
CN Pinouts:
See Table 4-16
The 4-pin power input connector is connected to a power supply.
Page 59
PCISA-9102 Half-Size CPU Card
Figure 4-16: Power Connector Location
PIN NO.
DESCRIPTION
1
+12V
2
GND
3
GND
4
+5V
Table 4-16: Power Connector Pinouts
4.2.15 SATA Drive Connectors
CN Label:
SATA1 and SATA2
CN Type:
7-pin SATA drive connectors (1x7)
CN Location:
See Figure 4-17
CN Pinouts:
See Table 4-17
The two SATA drive connectors are connected to two SATA drives. SATA drives transfer
data at speeds as high as 1.5 Gb/s.
Page 60
PCISA -9102 Half-Size CPU Card
Figure 4-17: SATA Drive Connector Locations
PIN NO.
DESCRIPTION
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
Table 4-17: SATA Drive Connector Pinouts
4.2.16 SDVO Connector
CN Label:
CN1
CN Type:
47-pin connector (1x47)
CN Location:
See Figure 4-18
CN Pinouts:
See Table 4-18
The 47-pin SDVO (Serial Digital Video Out) connector supports additional video signaling
interfaces.
Page 61
PCISA-9102 Half-Size CPU Card
Figure 4-18: SDVO Connector Pinout Locations
PIN NO. DESCRIPTION
PIN NO. DESCRIPTION
1
GROUND
25
GROUND
2
SDVOC_CLK-
26
SDVOB_BLUE-
3
SDVOC_CLK+
27
SDVOB_BLUE+
4
GROUND
28
GROUND
5
SDVOC_GREEN-
29
SDVOB_RED-
6
SDVOC_GREEN+
30
SDVOB_RED+
7
GROUND
31
GROUND
Page 62
PCISA -9102 Half-Size CPU Card
8
SDVOB_CLK-
32
SDVO1_STALL-
9
SDVOB_ CLK+
33
SDVO1_STALL+
10
GROUND
34
GROUND
11
SDVOB_GREEN-
35
SDVO_TVCLKIN-
12
SDVOB_GREEN+
36
SDVO_TVCLKIN+
13
GROUND
37
GROUND
14
SDVOC_INT+
38
SDVO_CLK
15
SDVOC_INT+
39
SDVO_DATA
16
GROUND
40
PCIRST
17
SDVOB_INT+
41
+5VS
18
SDVOB_INT+
42
+5VS
19
GROUND
43
+5VS
20
SDVOC_BLUE-
44
NC
21
SDVOC_BLUE+
45
NC
22
GROUND
46
GROUND
23
SDVOC_RED-
47
GROUND
24
SDVOC_RED+
Table 4-18: SDVO Connector Pinouts
4.2.17 Serial Port Connector (COM 1, RS-232)
CN Label:
COM1
CN Type:
10-pin header (2x5)
CN Location:
See Figure 4-19
CN Pinouts:
See Table 4-19
The 10-pin serial port connector provides a RS-232 serial communications channel. The
COM 1 serial port connector can be connected to external RS-232 serial port devices.
Page 63
PCISA-9102 Half-Size CPU Card
Figure 4-19: RS-232 Connector Pinout Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Data Carrier Direct (DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request To Send (RTS)
5
Transmit Data (TXD)
6
Clear To Send (CTS)
7
Data Terminal Ready (DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
Ground (GND)
Table 4-19: RS-232 Connector Pinouts
4.2.18 Serial Port Connector (COM 2, RS-232/422/485)
CN Label:
COM2
CN Type:
14-pin header (2x7)
CN Location:
See Figure 4-20
CN Pinouts:
See Table 4-20
The serial ports connectors connect to RS-232/422/485 serial port device.
Page 64
PCISA -9102 Half-Size CPU Card
Figure 4-20: 14-Pin Serial Port Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
GND
11
TXD 485+
12
TXD 485#
13
RXD 485+
14
RXD 485#
Table 4-20: COM 2 Pinouts
4.2.19 Internal USB Connectors
CN Label:
USB01 and USB23
CN Type:
8-pin header (2x4)
CN Location:
See Figure 4-21
CN Pinouts:
See Table 4-21
One 2x4 pin connector provides connectivity to two USB 2.0 ports. The USB ports are
used for I/O bus expansion.
Page 65
PCISA-9102 Half-Size CPU Card
Figure 4-21: Internal USB Connector Locations
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1
VCC
2
GND
3
DATA-
4
DATA+
5
DATA+
6
DATA-
7
GND
8
VCC
Table 4-21: Internal USB Pinouts
Page 66
PCISA -9102 Half-Size CPU Card
4.3 External Interface Connectors
The peripheral connectors on the back panel are connected to devices externally when
the PCISA-9102 is installed in a chassis. The peripheral connectors on the rear panel are:
1 x CRT connector
2 x RJ-45 Ethernet connectors
2 x USB 2.0 connectors
Figure 4-22: PCISA-9102 External Interface Connectors
4.3.1 CRT Connector
CN Label:
VGA1
CN Type:
15-pin female connector
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-22 and Figure 4-23
The standard 15-pin VGA connector connects to a CRT or LCD display monitor.
Figure 4-23: VGA Connector
Page 67
PCISA-9102 Half-Size CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
RED
2
GREEN
3
BLUE
4
N/C
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
N/C
12
DDC DAT
13
HSYNC
14
VSYNC
15
DDC CLK
Table 4-22: VGA Connector Pinouts
4.3.2 Ethernet Connectors
CN Label:
LAN1 and LAN2
CN Type:
RJ-45
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-23
The PCISA-9102 is equipped with two built-in GbE Ethernet controllers. The controllers
can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the
connector indicating the status of LAN. The pin assignments are listed in the following
table:
PIN
DESCRIPTION
PIN
DESCRIPTION
1
MDIA3-
5
MDIA1+
2
MDIA3+
6
MDIA2+
3
MDIA2-
7
MDIA0-
4
MDIA1-
8
MDIA0+
Table 4-23: LAN1 and LAN2 Pinouts
Page 68
PCISA -9102 Half-Size CPU Card
Figure 4-24: RJ-45 Ethernet Connector
The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green
LED indicates activity on the port and the yellow LED indicates the port is linked. See
Table 4-24.
SPEED LED
STATUS
DESCRIPTION
ACT/LINK LED
STATUS
DESCRIPTION
OFF
10Mbps connection
OFF
No link
GREEN
100Mbps connection
YELLOW
Linked
ORANGE
1Gbps connection
BLINKING
Data Activity
Table 4-24: RJ-45 Ethernet Connector LEDs
4.3.3 USB Connector
CN Label:
USB_C4 and USB_C5
CN Type:
USB port
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-25
USB devices can be connected directly to the USB connectors on the rear panel.
PIN NO.
DESCRIPTION
1
VCC
2
DATA-
3
DATA+
4
GND
Table 4-25: External USB Connector Pinouts
Page 69
PCISA-9102 Half-Size CPU Card
Chapter
5
5 Installation
Page 70
PCISA -9102 Half-Size CPU Card
5.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
PCISA-9102 may result in permanent damage to the PCISA-9102 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the PCISA-9102. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the PCISA-9102, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the PCISA-9102, place it on an
antic-static pad. This reduces the possibility of ESD damaging the
PCISA-9102.
Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
Page 71
PCISA-9102 Half-Size CPU Card
5.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before the PCISA-9102 is installed. All
installation notices pertaining to the installation of the PCISA-9102
should be strictly adhered to. Failing to adhere to these precautions
may lead to severe damage of the PCISA-9102 and injury to the
person installing the motherboard.
5.2.1 Installation Notices
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the PCISA-9102,
PCISA-9102 components and injury to the user.
Before and during the installation please DO the following:
Read the user manual:
o
The user manual provides a complete description of the PCISA-9102
installation instructions and configuration options.
Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
Place the PCISA-9102 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power to the PCISA-9102 off:
Page 72
PCISA -9102 Half-Size CPU Card
o
When working with the PCISA-9102, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the PCISA-9102 DO NOT:
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
Use the product before verifying all the cables and power connectors are
properly connected.
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
5.2.2 Installation Checklist
The following checklist is provided to ensure the PCISA-9102 is properly installed.
All the items in the packing list are present
The CPU is installed
The CPU cooling kit is properly installed
A compatible memory module is properly inserted into the slot
The jumpers have been properly configured
The PCISA-9102 is inserted into a chassis with adequate ventilation
The correct power supply is being used
The following devices are properly connected
o
o
o
o
o
o
IDE device
SATA drives
Power supply
USB cable
Parallel port cable
Serial port cable
The following external peripheral devices are properly connected to the
chassis:
o
o
o
VGA screen
RJ-45 Ethernet cable
USB devices
Page 73
PCISA-9102 Half-Size CPU Card
5.3 CPU, CPU Cooling Kit and DIMM Installation
WARNING:
A CPU should never be turned on without the specified cooling kit
being installed. If the cooling kit (heat sink and fan) is not properly
installed and the system turned on, permanent damage to the CPU,
PCISA-9102 and other electronic components attached to the system
may be incurred. Running a CPU without a cooling kit may also result
in injury to the user.
The CPU, CPU cooling kit and DIMM are the most critical components of the PCISA-9102.
If one of these component is not installed the PCISA-9102 cannot run.
5.3.1 Socket 479 CPU Installation
WARNING:
CPUs are expensive and sensitive components. When installing the
CPU please be careful not to damage it in anyway. Make sure the CPU
is installed properly and ensure the correct cooling kit is properly
installed.
To install a Socket 479 CPU onto the PCISA-9102, follow the steps below:
WARNING:
When handling the CPU, only hold it on the sides. DO NOT touch the
pins at the bottom of the CPU.
Step 1: Unlock the CPU retention screw. When shipped, the retention screw of the
Page 74
PCISA -9102 Half-Size CPU Card
CPU socket should be in the unlocked position. If it is not in the unlocked
position, use a screwdriver to unlock the screw. See Figure 5-1.
Figure 5-1: Make sure the CPU socket retention screw is unlocked
Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
compressed air.
Step 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is
facing upwards.
Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the
CPU socket. See Figure 5-1.
Step 5: Align the CPU pins. Carefully align the CPU pins with the holes in the CPU
socket.
Step 6: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are
properly aligned, the CPU should slide into the CPU socket smoothly.
Step 7: Lock the retention screw. Rotate the retention screw into the locked position.
See Figure 5-2.Step 0:
Page 75
PCISA-9102 Half-Size CPU Card
Figure 5-2: Lock the CPU Socket Retention Screw
5.3.2 Cooling Kit CF-479B-RS Installation
Figure 5-3: IEI CF-479B-RS Cooling Kit
An IEI Socket 479 CPU cooling kit can be purchased separately. The cooling kit
comprises a CPU heat sink and a cooling fan.
Page 76
PCISA -9102 Half-Size CPU Card
WARNING:
Do not wipe off (accidentally or otherwise) the pre-sprayed layer of
thermal paste on the bottom of the CF-479B-RS heat sink. The thermal
paste between the CPU and the heat sink is important for optimum
heat dissipation.
To install the CF-479B-RS cooling kit, please follow the steps below.
Step 1: Place the cooling kit onto the CPU. Make sure the CPU cooling fan cable
can be properly routed when the cooling kit is installed.
Step 2: Properly align the cooling kit. Make sure its four spring screw fasteners can
pass through the pre-drilled holes on the PCB.
Step 3: Secure the cooling kit. From the solder side of the PCB, align the support
bracket to the screw threads on heat sink that were inserted through the PCB
holes. (See Figure 5-4)
Figure 5-4: Cooling Kit Support Bracket
Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each
nut a few turns at a time and do not over-tighten the screws.
Page 77
PCISA-9102 Half-Size CPU Card
Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the motherboard. Carefully route the cable and avoid heat generating chips
and fan blades. See Figure 5-5. Step 0:
Figure 5-5: Connect the cooling fan cable
5.3.3 DIMM Installation
WARNING:
Only DDR2 memory module can be installed on the PCISA-9102. Do
not install DDR memory modules. If a DDR memory module is installed
on the PCISA-9102, the PCISA-9102 may be irreparably damaged.
Please make sure the purchased DIMM complies with the memory
specifications of the PCISA-9102. DIMM specifications compliant with
the PCISA-9102 are listed in Chapter 2.
Page 78
PCISA -9102 Half-Size CPU Card
CAUTION:
The DIMM1 socket must be installed with one DDR2 DIMM to enable
the PCISA-9102 to boot-up properly.
To install a DIMM into a DIMM socket, please follow the steps below and refer to
Figure 5-6.
Figure 5-6: Installing a DIMM
Step 1: Open the DIMM socket handles. The DIMM socket has two handles that
secure the DIMM into the socket. Before the DIMM can be inserted into the
socket, the handles must be opened. See Figure 5-6.
Step 2: Align the DIMM with the socket. The DIMM must be oriented in such a way
that the notch in the middle of the DIMM must be aligned with the plastic bridge
in the socket. See Figure 5-6.
Step 3: Insert the DIMM. Once properly aligned, the DIMM can be inserted into the
socket. As the DIMM is inserted, the white handles on the side of the socket will
Page 79
PCISA-9102 Half-Size CPU Card
close automatically and secure the DIMM to the socket. See Figure 5-6.
Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The
memory module is ejected by a mechanism in the socket.Step 0:
5.4 Jumper Settings
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect
them. To CLOSE/SHORT a jumper means
connecting the pins of the jumper with the plastic
clip and to OPEN a jumper means removing the
Figure 5-7: Jumper Locations
plastic clip from a jumper.
Before the PCISA-9102 is installed in the system, the jumpers must be set in accordance
with the desired configuration. The jumpers on the PCISA-9102 are listed in Table 5-1.
Description
Label
Type
CF card setup
JCF1
2-pin header
CPU frequency selection
J_FREQ1
3-pin header
Clear CMOS
J_CMOS1
3-pin header
COM 2 function selection
JP1
6-pn header
LVDS LCD voltage selection
J_VLVDS1
3-pin header
LVDS LCD resolution selection
J_LCD_TYPE1
8-pin header
Table 5-1: Jumpers
Page 80
PCISA -9102 Half-Size CPU Card
5.4.1 AT Power Select Jumper Settings
Jumper Label:
ATXCTL1
Jumper Type:
3-pin wafer
Jumper Settings:
See Table 5-2
Jumper Location:
See Figure 5-8
The AT Power Select jumper specifies the systems power mode as AT or ATX. AT Power
When the ATXCTL1 connector is set to ATX mode (open), please refer to Section 4.2.1
for the pinouts of this ATX power enable connector. Select jumper settings are shown in
Table 5-2.
AT Power Select
Description
Short 1-2
Use AT power
Open
Use ATX power
Default
Table 5-2: AT Power Select Jumper Settings
The location of the AT Power Select jumper is shown in Figure 5-8 below.
Figure 5-8: AT Power Select Jumper Location
Page 81
PCISA-9102 Half-Size CPU Card
5.4.2 CF Card Setup
Jumper Label:
JCF1
Jumper Type:
2-pin header
Jumper Settings:
See Table 5-3
Jumper Location:
See Figure 5-9
The CF Card Setup jumper sets the CF Type I card or CF Type II cards as either the slave
device or the master device. CF Card Setup jumper settings are shown in Table 5-3.
CF Card Setup
Description
Open
Slave
Closed
Master
Default
Table 5-3: CF Card Setup Jumper Settings
The CF Card Setup jumper location is shown in Figure 5-9.
Figure 5-9: CF Card Setup Jumper Location
Page 82
PCISA -9102 Half-Size CPU Card
5.4.3 Clear CMOS Jumper
Jumper Label:
J_CMOS1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-4
Jumper Location:
See Figure 5-10
If the PCISA-9102 fails to boot due to improper BIOS settings, the clear CMOS jumper
clears the CMOS data and resets the system BIOS information. To do this, use the jumper
cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1
and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
The clear CMOS jumper settings are shown in Table 5-4.
Clear CMOS
Description
Short 1 - 2
Keep CMOS Setup
Short 2 - 3
Clear CMOS Setup
Default
Table 5-4: Clear CMOS Jumper Settings
The location of the clear CMOS jumper is shown in Figure 5-10 below.
Page 83
PCISA-9102 Half-Size CPU Card
Figure 5-10: Clear CMOS Jumper
5.4.4 COM 2 Function Select Jumper
Jumper Label:
JP1
Jumper Type:
6-pin header
Jumper Settings:
See Table 5-5
Jumper Location:
See Figure 5-11
The COM 2 Function Select jumper sets the communication protocol used by the second
serial communications port (COM 2) as RS-232, RS-422 or RS-485. The COM 2 Function
Select settings are shown in Table 5-5.
COM 2 Function Select
Description
Short 1-2
RS-232
Short 3-4
RS-422
Short 5-6
RS-485
Default
Table 5-5: COM 2 Function Select Jumper Settings
The COM 2 Function Select jumper location is shown in Figure 5-11.
Page 84
PCISA -9102 Half-Size CPU Card
Figure 5-11: COM 2 Function Select Jumper Location
5.4.5 CPU Frequency Selection
Jumper Label:
J_FREQ1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-6
Jumper Location:
See Figure 5-12
The CPU Frequency setup jumper enables a user to select the frequency of the CPU on
the PCISA-9102. The FSB CPU Frequency jumper settings are shown in Table 5-6.
FSB Setup
Description
Short 1 – 2
400 MHz
Short 2 – 3
533 MHz
Default
Table 5-6: CPU Frequency Setup Jumper Settings
The location of the CPU Frequency Setup jumper is shown in Figure 5-12 below.
Page 85
PCISA-9102 Half-Size CPU Card
Figure 5-12: CPU Frequency Setup Jumper
5.4.6 LVDS Voltage Selection
WARNING:
Permanent damage to the screen and PCISA-9102 may occur if the
wrong voltage is selected with this jumper. Please refer to the user
guide that cam with the monitor to select the correct voltage.
Jumper Label:
J_VLVDS1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-7
Jumper Location:
See Figure 5-13
The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set. The
LVDS Voltage Selection jumper settings are shown in Table 5-7.
Page 86
PCISA -9102 Half-Size CPU Card
LVDS Voltage Select
Description
Short 1-2
+3.3V
Short 2-3
+5V
Default
Table 5-7: LVDS Voltage Selection Jumper Settings
The LVDS Voltage Selection jumper location is shown in Figure 5-13.
Figure 5-13: LVDS Voltage Selection Jumper Pinout Locations
5.4.7 LVDS Panel Resolution Selection
Jumper Label:
J_LCD_TYPE1
Jumper Type:
8-pin header
Jumper Settings:
See Table 5-8
Jumper Location:
See Figure 5-14
The LVDS Panel Resolution Selection jumper allows the LVDS screen resolution to be
set. The LVDS Panel Resolution Selection jumper settings are shown in Table 5-8.
Page 87
PCISA-9102 Half-Size CPU Card
LVDS Resolution Select
Description
Open
By software
Short 1-2
640 x 480 (18-bit)
Short 3-4
800 x 600 (18-bit)
Short 1-2 & 3-4
1024 x 768 (18-bit)
Short 5-6
1024 x 768 (24-bit)
Short 1-2 & 5-6
Reserved
Short 3-4 & 5-6
1280 x 1024 (48-bit)
Short 1-2 & 3-4 & 5-6
1600 x 1200 (48-bit)
Short 7-8
1280 x 768 (18-bit)
Short 1-2 & 7-8
1280 x 800 (18-bit)
Short 3-4 & 7-8
1366 x 768 (24-bit)
Short 1-2 & 3-4 & 7-8
1440 x 900 (36-bit)
Short 5-6 & 7-8
1440 x 900 (48-bit)
Default
Table 5-8: LVDS Resolution Selection Jumper Settings
The LVDS Voltage Selection jumper location is shown in Figure 5-14.
Figure 5-14: LVDS Resolution Selection Jumper Pinout Locations
Page 88
PCISA -9102 Half-Size CPU Card
5.5 Chassis Installation
5.5.1 Airflow
WARNING:
Airflow is critical to the cooling of the CPU and other onboard
components. The chassis in which the PCISA-9102 must have air
vents to allow cool air to move into the system and hot air to move out.
The PCISA-9102 must be installed in a chassis with ventilation holes on the sides allowing
airflow to travel through the heat sink surface. In a system with an individual power supply
unit, the cooling fan of a power supply can also help generate airflow through the board
surface.
NOTE:
IEI has a wide range of backplanes available. Please contact your
PCISA-9102 vendor, reseller or an IEI sales representative at
[email protected] or visit the IEI website (http://www.ieiworld.com.tw)
to find out more about the available chassis.
5.5.2 Backplane Installation
Before the PCISA-9102 can be installed into the chassis, a backplane must first be
installed. Please refer to the installation instructions that came with the backplane and the
chassis to see how to install the backplane into the chassis.
Page 89
PCISA-9102 Half-Size CPU Card
NOTE:
IEI has a wide range of backplanes available. Please contact your
PCISA-9102 vendor, reseller or an IEI sales representative at
[email protected] or visit the IEI website (http://www.ieiworld.com.tw)
to find out more about the available chassis.
5.5.3 CPU Card Installation
To install the PCISA-9102 CPU card onto the backplane, carefully align the CPU card
interface connectors with the corresponding socket on the backplane. To do this, please
refer to the reference material that came with the backplane. Next, secure the CPU card to
the chassis. To do this, please refer to the reference material that came with the chassis.
5.6 Internal Peripheral Device Connections
5.6.1 Peripheral Device Cables
The cables listed in Table 5-9 are shipped with the PCISA-9102.
Quantity
Type
1
IDE cable
1
Parallel port and RS-232 cable
2
SATA drive cables
1
SATA drive power cable
1
USB cable
Table 5-9: IEI Provided Cables
Optional cables are listed below:
FDD cable
Page 90
PCISA -9102 Half-Size CPU Card
Keyboard/mouse cable
RS-232/422/485 cable
5.6.2 IDE Cable Connection
The IDE flat cable connects to the PCISA-9102 to one or two IDE devices. To connect an
IDE HDD to the PCISA-9102, please follow the instructions below.
Step 1: Locate the IDE connector. The location of the IDE device connector is shown
in Chapter 3.
Step 2: Insert the connector. Connect the IDE cable connector to the onboard
connector. See Figure 5-15. A key on the front of the cable connector ensures it
can only be inserted in one direction.
Figure 5-15: IDE Cable Connection
Step 3: Connect the cable to an IDE device. Connect the two connectors on the other
side of the cable to one or two IDE devices. Make sure that pin 1 on the cable
corresponds to pin 1 on the connector.Step 0:
Page 91
PCISA-9102 Half-Size CPU Card
5.6.3 SATA Drive Connection
The PCISA-9102 is shipped with two SATA drive cables and one SATA drive power cable.
To connect the SATA drives to the connectors, please follow the steps below.
Step 1: Locate the connectors. The locations of the SATA drive connectors are shown
in Chapter 3.
Step 2: Insert the cable connector. Press the clip on the connector at the end of the
SATA cable and insert the cable connector into the onboard SATA drive
connector. See Figure 5-16.
Figure 5-16: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 5-17.
Step 4: Connect the SATA power cable. Connect the SATA power connector to the
back of the SATA drive. See Figure 5-17. Step 0:
Page 92
PCISA -9102 Half-Size CPU Card
Figure 5-17: SATA Power Drive Connection
5.6.4 USB Cable (Dual Port) with Slot Bracket
The PCISA-9102 can be shipped with a dual port USB 2.0 cable. To connect the USB
cable connector, please follow the steps below.
Step 1: Locate the connectors. The locations of the USB connectors are shown in
Chapter 3.
WARNING:
If the USB pins are not properly aligned, the USB device can burn out.
Step 2: Align the connectors. The cable has two connectors. Correctly align pin 1on
each cable connector with pin 1 on the PCISA-9102 USB connector.
Step 3: Insert the cable connectors. Once the cable connectors are properly aligned
with the USB connectors on the PCISA-9102, connect the cable connectors to
Page 93
PCISA-9102 Half-Size CPU Card
the onboard connectors. See Figure 5-18.
Figure 5-18: Dual USB Cable Connection
Step 4: Attach the bracket to the chassis. The USB 2.0 connectors are attached to a
bracket. To secure the bracket to the chassis please refer to the installation
instructions that came with the chassis.Step 0:
5.6.5 7.1 Channel Audio Kit Installation (Optional)
NOTE:
This is an optional item that must be ordered separately. For further
information please contact the nearest PCISA-9102 distributor, reseller
or vendor or contact an iEi sales representative directly. Send any
queries to [email protected]
The optional 7.1 channel audio kit connects to the 10-pin audio connector on the
PCISA-9102. The audio kit consists of five audio jacks. One audio jack, Mic In, connects
to a microphone. The remaining four audio jacks, Line-In, Front-Out, Rear-Out, and
Page 94
PCISA -9102 Half-Size CPU Card
Center Subwoofer, connect to speakers. To install the audio kit, please refer to the steps
below:
Step 1: Connect the audio kit cable. The audio kit is shipped with a cable that
connects the audio kit to the PCISA-9102. Connect the cable to the connector
on the back of the audio kit. Make sure the pins are properly aligned (i.e. pin 1
connects to pin 1).
Step 2: Locate the audio connector. The location of the 10-pin audio connector is
shown in Chapter 3.
Step 3: Align pin 1. Align pin 1 on the on-board connector with pin 1 on the audio kit
cable connector. Pin 1 on the audio kit cable connector is indicated with a white
dot. See Figure 5-19.
Figure 5-19: 7.1 Channel Audio Kit
Step 4: Mount the audio kit onto the chassis. Once the audio kit is connected to the
PCISA-9102, secure the audio kit bracket to the system chassis.
Step 5: Connect the audio devices. Connect one speaker to the line-in audio jack, one
speaker to the line-out audio jack and a microphone to the mic-in audio jack.
Page 95
PCISA-9102 Half-Size CPU Card
Step 6: Install the driver. If the 7.1 channel audio kit is used, the ALC883 Realtek
codec driver must be installed. Refer to Chapter 7 for driver installation
instructions.Step 0:
5.7 External Peripheral Interface Connection
The following external peripheral devices can be connected to the external peripheral
interface connectors.
RJ-45 Ethernet cables
USB devices
VGA monitor
To install these devices, connect the corresponding cable connector from the actual
device to the corresponding PCISA-9102 external peripheral interface connector making
sure the pins are properly aligned.
5.7.1 LAN Connection (Single Connector)
There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection
to an external network. To connect a LAN cable with an RJ-45 connector, please follow
the instructions below.
Step 1: Locate the RJ-45 connectors. The locations of the USB connectors are shown
in Chapter 4.
Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of
the RJ-45 connectors on the PCISA-9102. See Figure 5-20.
Page 96
PCISA -9102 Half-Size CPU Card
Figure 5-20: LAN Connection
Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN
cable RJ-45 connector into the on-board RJ-45 connector. Step 0:
5.7.2 VGA Monitor Connection
The PCISA-9102 has a single female DB-15 connector on the external peripheral interface
panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor
to the PCISA-9102, please follow the instructions below.
Step 1: Locate the female DB-15 connector. The location of the female DB-15
connector is shown in Chapter 3.
Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen
cable with the female DB-15 connector on the external peripheral interface.
Step 3: Insert the VGA connector. Once the connectors are properly aligned with the
insert the male connector from the VGA screen into the female connector on the
PCISA-9102. See Figure 5-21.
Page 97
PCISA-9102 Half-Size CPU Card
Figure 5-21: VGA Connector
Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA
monitor to the external interface by tightening the two retention screws on either
side of the connector. Step 0:
5.7.3 USB Device Connection (Single Connector)
There are two external USB 2.0 connectors. Both connectors are perpendicular to the
PCISA-9102. To connect a USB 2.0 or USB 1.1 device, please follow the instructions
below.
Step 1: Located the USB connectors. The locations of the USB connectors are shown
in Chapter 4.
Step 2: Align the connectors. Align the USB device connector with one of the
connectors on the PCISA-9102. See Figure 5-22.
Page 98
PCISA -9102 Half-Size CPU Card
Figure 5-22: USB Device Connection
Step 3: Insert the device connector. Once aligned, gently insert the USB device
connector into the on-board connector. Step 0:
Page 99
PCISA-9102 Half-Size CPU Card
Chapter
6
6 AMI BIOS
Page 100
PCISA -9102 Half-Size CPU Card
6.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
6.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP”
message appears on the screen. 0.
If the message disappears before the DELETE key is pressed, restart the computer and try
again.
6.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Page Up key
Increase the numeric value or make changes
Page Dn key
Decrease the numeric value or make changes
Page 101
PCISA-9102 Half-Size CPU Card
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 6-1: BIOS Navigation Keys
6.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
6.1.4 Unable to Reboot After Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 5.
6.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Power Changes power management settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 102
PCISA -9102 Half-Size CPU Card
6.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
Type: Names the currently installed processor
Speed: Lists the processor speed
Page 103
PCISA-9102 Half-Size CPU Card
o
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size:
Lists memory size
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
6.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system to
malfunction. Make sure that the settings made are compatible with the
hardware.
CPU Configuration (see Section 6.3.1)
IDE Configuration (see Section 6.3.2)
Floppy Configuration (see Section 6.3.3)
Super IO Configuration (see Section 6.3.4)
Hardware Health Configuration (see Section 6.3.5)
Remote Access Configuration (see Section )
USB Configuration (see Section 6.3.7)
Page 104
PCISA -9102 Half-Size CPU Card
BIOS Menu 2: Advanced No Power
6.3.1 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications
and configure the CPU.
Page 105
PCISA-9102 Half-Size CPU Card
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
6.3.2 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration
of the IDE devices installed in the system.
Page 106
PCISA -9102 Half-Size CPU Card
BIOS Menu 4: IDE Configuration
ATA/IDE Configurations [Compatible]
Use the ATA/IDE Configurations option to configure the ATA/IDE controller.
Disables the on-board ATA/IDE controller.
Disabled
Compatible
DEFAULT
Configures the on-board ATA/IDE controller to be in
compatible mode. In this mode, a SATA channel will
replace one of the IDE channels. This mode supports up
to 4 storage devices.
Enhanced
Configures the on-board ATA/IDE controller to be in
Enhanced mode. In this mode, IDE channels and SATA
channels are separated. This mode supports up to 6
storage devices. Some legacy OS do not support this
mode.
Page 107
PCISA-9102 Half-Size CPU Card
Legacy IDE Channels [SATA Pri, PATA Sec]
SATA Only
SATA Pri., PATA Sec
DEFAULT
PATA Only
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 6.3.2.1 appear.
6.3.2.1 IDE Master, IDE Slave
Use the IDE Master and IDE Slave configuration menu to view both primary and
secondary IDE device details and configure the IDE devices connected to the system.
Page 108
PCISA -9102 Half-Size CPU Card
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from
after the Power-On Self-Test (POST) is complete.
BIOS is prevented from searching for an IDE disk
Not Installed
drive on the specified channel.
Auto
DEFAULT
The BIOS auto detects the IDE disk drive type
attached to the specified channel. This setting should
be used if an IDE hard disk drive is attached to the
specified channel.
CD/DVD
The CD/DVD option specifies that an IDE CD-ROM
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
Page 109
PCISA-9102 Half-Size CPU Card
IDE disk drives on the specified channel.
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical
Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
BIOS is prevented from using the LBA mode control on
Disabled
the specified channel.
Auto
DEFAULT
BIOS auto detects the LBA mode control on the specified
channel.
Block (Multi Sector Transfer) [Auto]
Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the
device supports multi-sector transfers.
BIOS is prevented from using Multi-Sector Transfer on the
Disabled
specified channel. The data to and from the device occurs
one sector at a time.
Auto
DEFAULT
BIOS auto detects Multi-Sector Transfer support on the
drive on the specified channel. If supported the data
transfer to and from the device occurs multiple sectors at
a time.
Page 110
PCISA -9102 Half-Size CPU Card
PIO Mode [Auto]
Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
BIOS auto detects the PIO mode. Use this value if the IDE disk
drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
DMA Mode [Auto]
Use the DMA Mode BIOS selection to adjust the DMA mode options.
Auto
DEFAULT
BIOS auto detects the DMA mode. Use this value if the IDE
disk drive support cannot be determined.
SWDMA0
Single Word DMA mode 0 selected with a maximum data
transfer rate of 2.1MBps
SWDMA1
Single Word DMA mode 1 selected with a maximum data
transfer rate of 4.2MBps
SWDMA2
Single Word DMA mode 2 selected with a maximum data
transfer rate of 8.3MBps
Page 111
PCISA-9102 Half-Size CPU Card
MWDMA0
Multi Word DMA mode 0 selected with a maximum data
transfer rate of 4.2MBps
MWDMA1
Multi Word DMA mode 1 selected with a maximum data
transfer rate of 13.3MBps
MWDMA2
Multi Word DMA mode 2 selected with a maximum data
transfer rate of 16.6MBps
UDMA1
Ultra DMA mode 0 selected with a maximum data transfer
rate of 16.6MBps
UDMA1
Ultra DMA mode 1 selected with a maximum data transfer
rate of 25MBps
UDMA2
Ultra DMA mode 2 selected with a maximum data transfer
rate of 33.3MBps
UDMA3
Ultra DMA mode 3 selected with a maximum data transfer
rate of 44MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
UDMA4
Ultra DMA mode 4 selected with a maximum data transfer
rate of 66.6MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
UDMA5
Ultra DMA mode 5 selected with a maximum data transfer
rate of 99.9MBps (To use this mode, it is required that an
80-conductor ATA cable is used.)
S.M.A.R.T [Auto]
Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and
Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Page 112
PCISA -9102 Half-Size CPU Card
Auto
DEFAULT
BIOS auto detects HDD SMART support.
Disabled
Prevents BIOS from using the HDD SMART feature.
Enabled
Allows BIOS to use the HDD SMART feature
32Bit Data Transfer [Enabled]
Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on supported
hard disk drives.
6.3.3 Floppy Configuration
Use the Floppy Configuration menu to configure the floppy disk drive connected to the
system.
BIOS Menu 6: IDE Master and IDE Slave Configuration
Page 113
PCISA-9102 Half-Size CPU Card
Floppy A
Use the Floppy A option to configure the floppy disk drive. Options are listed below:
Disabled
360 KB 51/4”
1.2 MB 51/4”
720 KB 31/2”
1.44 MB 31/2’
2.88 MB 31/2”
6.3.4 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 7) to set or change the
configurations for the FDD controllers, parallel ports and serial ports.
BIOS Menu 7: Super IO Configuration
Page 114
PCISA -9102 Half-Size CPU Card
Serial Port1 Address [3F8/IRQ4]
Use the Serial Port1 Address option to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 1 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Address [2F8/IRQ3]
Use the Serial Port2 Address option to select the Serial Port 2 base address.
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
DEFAULT
Serial Port 2 I/O port address is 3F8 and the interrupt
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Mode [Normal]
Use the Serial Port2 Mode option to select the Serial Port2 operational mode.
Normal
IrDA
DEFAULT
Serial Port 2 mode is normal
Serial Port 2 mode is IrDA
Page 115
PCISA-9102 Half-Size CPU Card
Serial Port 2 mode is ASK IR
ASK IR
Parallel Port Address [378]
Use the Parallel Port Address option to select the parallel port base address.
No base address is assigned to the Parallel Port
Disabled
378
DEFAULT
Parallel Port I/O port address is 378
278
Parallel Port I/O port address is 278
3BC
Parallel Port I/O port address is 3BC
Parallel Port Mode [Normal]
Use the Parallel Port Mode option to select the mode the parallel port operates in.
Normal
DEFAULT
The normal parallel port mode is the standard mode
for parallel port operation.
Bi-Directional
Parallel port outputs are 8-bits long. Inputs are
accomplished by reading 4 of the 8 bits on the
status register.
EPP
The parallel port operates in the enhanced parallel
port mode (EPP). The EPP mode supports
bi-directional communication between the system
and the parallel port device and the transmission
rates between the two are much faster than the
Normal mode.
ECP
The
parallel port
operates
in
the
extended
capabilities port (ECP) mode. The ECP mode
supports bi-directional communication between the
system and the parallel port device and the
Page 116
PCISA -9102 Half-Size CPU Card
transmission rates between the two are much faster
than the Normal mode
ECP+EPP
The parallel port is compatible with both EPP and
ECP devices described above
Parallel Port IRQ [IRQ7]
Use the Parallel Port IRQ selection to set the parallel port interrupt address.
IRQ5 is assigned as the parallel port interrupt address
IRQ5
IRQ7
DEFAULT
IRQ7 is assigned as the parallel port interrupt address
6.3.5 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 8) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 8: Hardware Health Configuration
Page 117
PCISA-9102 Half-Size CPU Card
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures: The following system temperatures are monitored
o
o
o
CPU Temperature
PWM Temperature
System Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
CPU Fan Speed
Voltages: The following system voltages are monitored
o
o
o
o
o
o
+1.5V
+1.8V
+3.3V
+5V
+12.0V
VBAT
CPU FAN Mode Setting [Manual Mode]
Use the CPU FAN1 Mode Setting option to configure the second fan.
Manual Mode
Thermal
DEFAULT
Cruise
Mode
Fan is on all the time
If selected, the following appears with
values that can be selected:
Target CPU Temp Value
CPU Temp Tolerance Value
CPU FAN StartUp Value
CPU FAN Stop Value
CPU FAN StopTime Value
Speed Cruise Mode
Page 118
If selected, the following appears with
PCISA -9102 Half-Size CPU Card
values that can be selected:
CPU FAN TargetSpeed Value
CPU Temp Tolerance Value
CPU Fan PWM Control [250]
The CPU Fan PWM Control option can only be set if the CPU FAN Mode Setting option
is set to Manual Mode. Use the CPU Fan PWM Control option to select PWM duty cycle
control. The PWM duty cycle specifies the width of the modulated pulse. A high value
ensures a wide pulse and a low value ensures a narrow pulse. To select a value, select
the CPU Fan PWM Control option and enter a decimal number between 000 and 255.
The PWM Duty Cycle control range is specified below.
PWM Minimum Mode: 0
PWM Maximum Mode: 255
6.3.6 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 9) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
Page 119
PCISA-9102 Half-Size CPU Card
BIOS Menu 9: Remote Access Configuration [Advanced]
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Disabled
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Redirection after BIOS POST
Terminal Type
Page 120
PCISA -9102 Half-Size CPU Card
These configuration options are discussed below.
Serial Port Number [COM1]
Use the Serial Port Number option allows users to select the serial port used for remote
access.
COM1
DEFAULT
COM2
System is remotely accessed through COM1
System is remotely accessed through COM2
NOTE: Make sure the selected COM port is enabled through the Super I/O configuration
menu.
Base Address, IRQ [3F8h,4]
The Base Address, IRQ option cannot be configured and only shows the interrupt
address of the serial port listed above.
Serial Port Mode [115200 8,n,1]
Use the Serial Port Mode option to select baud rate through which the console redirection
is made. The following configuration options are available
115200 8,n,1 DEFAULT
57600 8,n,1
38400 8,n,1
19200 8,n,1
09600 8,n,1
NOTE:
Identical baud rate setting musts be set on the host (a management
computer running a terminal software) and the slave
Page 121
PCISA-9102 Half-Size CPU Card
Redirection After BIOS POST [Always]
Use the Redirection After BIOS POST option to specify when console redirection should
occur.
Disabled
The console is not redirected after POST
Boot Loader
Redirection is active during POST and during Boot
Loader
Always
DEFAULT
Redirection is always active (Some OSes may not
work if set to Always)
Terminal Type [ANSI]
Use the Terminal Type BIOS option to specify the remote terminal type.
ANSI
DEFAULT
The target terminal type is ANSI
VT100
The target terminal type is VT100
VT-UTF8
The target terminal type is VT-UTF8
6.3.7 USB Configuration
Use the USB Configuration menu (BIOS Menu 10) to read USB configuration
information and configure the USB settings.
Page 122
PCISA -9102 Half-Size CPU Card
BIOS Menu 10: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
USB Function [6 USB Ports]
Use the USB Function BIOS option to enable or disable a specified number of USB ports.
If only two USB ports are being used, disabling the remaining six USB frees up system
resources that can be redirected elsewhere.
Disabled
USB function support disabled
Page 123
PCISA-9102 Half-Size CPU Card
2 USB Ports
Two USB ports are enabled
4 USB Ports
Four USB ports are enabled
6 USB Ports
DEFAULT
Six USB ports are enabled
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
USB 2.0 controller disabled
Disabled
Enabled
DEFAULT
USB 2.0 controller enabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Legacy USB support disabled
Disabled
Enabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
Auto
connected
USB2.0 Controller Mode [HiSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
The controller is capable of operating at 12Mb/s
FullSpeed
HiSpeed
Page 124
DEFAULT
The controller is capable of operating at 480Mb/s
PCISA -9102 Half-Size CPU Card
6.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 11) to configure advanced PCI and PnP settings.
WARNING!
Setting wrong values for the BIOS selections in the PCIPnP BIOS menu
may cause the system to malfunction.
BIOS Menu 11: PCI/PnP Configuration
IRQ#
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
The specified IRQ is available to be used by
Page 125
PCISA-9102 Half-Size CPU Card
PCI/PnP devices
The specified IRQ is reserved for use by Legacy ISA
Reserved
devices
Available IRQ addresses options are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
Reserved
The specified DMA is reserved for use by Legacy
ISA devices
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Page 126
PCISA -9102 Half-Size CPU Card
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
6.5 Boot
Use the Boot menu (BIOS Menu 12) to configure system boot options.
BIOS Menu 12: Boot
Page 127
PCISA-9102 Half-Size CPU Card
6.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 13) to configure advanced
system boot options.
BIOS Menu 13: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Page 128
PCISA -9102 Half-Size CPU Card
Normal POST messages displayed
Disabled
Enabled
DEFAULT
OEM Logo displayed instead of POST messages
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
Page 129
PCISA-9102 Half-Size CPU Card
Boot From LAN Support [Disabled]
Use the BOOT From LAN Support option to enable the Broadcom PCIe GbE controller to
boot the system.
Disabled
DEFAULT
Cannot be booted from a remote system through the
Broadcom PCIe GbE controller
Enabled
Can be booted from a remote system through the
Broadcom PCIe GbE controller
6.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 14) to specify the boot sequence from
the available devices. Possible boot devices may include:
USB
HDD
CD/DVD
BIOS Menu 14: Boot Device Priority Settings
Page 130
PCISA -9102 Half-Size CPU Card
6.5.3 Removable Drives
Use the Removable Drives menu (BIOS Menu 15) to specify the boot sequence of the
available USB devices. When the menu is opened, the USB devices connected to the
system are listed as shown below:
1st Drive
[1st USB]
2nd Drive
[2nd USB]
NOTE:
Only the drives connected to the system are shown. For example, if only
one USB device is connected only “1st Drive” is listed.
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available USB devices is shown. Select the first USB device the system
boots from. If the “1st Drive” is not used for booting this option may be disabled.
BIOS Menu 15: Removable Drives
Page 131
PCISA-9102 Half-Size CPU Card
6.6 Security
Use the Security menu (BIOS Menu 16) to set system and user passwords.
BIOS Menu 16: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
Page 132
PCISA -9102 Half-Size CPU Card
6.7 Chipset
Use the Chipset menu to access the Northbridge and Southbridge menus.
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
6.7.1 Northbridge Configuration
Use the Northbridge Chipset Configuration menu (BIOS Menu 17) to configure the
Northbridge chipset.
BIOS Menu 17:Northbridge Chipset Configuration
Page 133
PCISA-9102 Half-Size CPU Card
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see if
it is necessary to reserve the space.
Disabled
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
15MB – 16MB
ISA expansion cards
Internal Graphics Mode Select [Enable, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
DEFAULT
8MB of memory used by internal graphics device
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
DEFAULT
Graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Combo Mode
A fixed portion of graphics memory is reserved as
graphics memory. If more memory is needed,
graphics
Page 134
memory
is
dynamically
allocated
PCISA -9102 Half-Size CPU Card
according to the system and graphics needs.
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Boot Display Device [Auto]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration options are listed below.
Auto
DEFAULT
CRT
LFP
Flat Panel Type [1024x768 18b]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
640x480 18b
800x600 18b
1024x768 18b
1024x768 24b
1280x1024 48b
1600x1200 48b
1280x768 18b
1280x800 18b
1366x768 24b
1440x900 36b
Page 135
PCISA-9102 Half-Size CPU Card
1440x900 48b
6.7.2 Southbridge Configuration
The Southbridge Configuration menu (BIOS Menu 18) allows the Southbridge chipset
to be configured.
BIOS Menu 18:Southbridge Chipset Configuration
Azalia/AC97 Selection [Azalia]
Use the Azalia/AC97 Selection option to select the audio codec.
Azalia
AC’97
DEFAULT
Audio
The HD Audio is enabled
The onboard AC’97 is enabled
Only
All Disabled
Page 136
The AC’97 and HD Audio are all disabled.
PCISA -9102 Half-Size CPU Card
Onboard BCM5787 Port n [Enabled]
Use the Onboard BCM5787 Port n option to determine enable or disable the nth
Broadcom BCM5787 PCIe GbE port.
nth PCI Express port disabled.
Disabled
Enabled
DEFAULT
nth PCI Express port enabled.
6.8 Power
The Power menu (BIOS Menu 19) allows the advanced power management options to be
configured.
BIOS Menu 19:Power
Power Supply Mode [BY HARDWARE]
Use the Power Supply Mode BIOS to specify how the power supply mode.
AT
The power supply mode is set to AT.
Page 137
PCISA-9102 Half-Size CPU Card
If selected, the following appears with values that
ATX
can be selected:
Power Button Mode
Restore on AC Power Loss
Suspend Mode
RTC Resume
RI Resume
Resume On KeyBoard/Mouse
BY
DEFAULT
HARDWARE
The power supply mode is set by the onboard
jumper.
6.9 Exit
Use the Exit menu (BIOS Menu 20) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Page 138
PCISA -9102 Half-Size CPU Card
BIOS Menu 20: Exit
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Page 139
PCISA-9102 Half-Size CPU Card
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 140
PCISA -9102 Half-Size CPU Card
Chapter
7
7 Software Drivers
Page 141
PCISA-9102 Half-Size CPU Card
7.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product
and is subject to change without prior notice. Visit the IEI website or
contact technical support for the latest updates.
The following drivers can be installed on the system:
Intel® chipset driver
VGA driver
LAN drivers
Audio driver
SATA driver
Installation instructions are given below.
7.2 Driver CD Auto-run
All the drivers for the PCISA-9102 are on the CD that came with the system. To install the
drivers, please follow the steps below.
Step 1: Insert the CD into a CD drive connected to the system.
NOTE:
If the system does not initiate the "autorun" program when the CD is
inserted, click the Start button, select Run, then type X:\autorun.exe
(where X:\ is the system CD drive) to access the IEI Driver CD main
menu.
Step 2: The driver main menu appears (Figure 7-1).
Page 142
PCISA -9102 Half-Size CPU Card
Figure 7-1: Introduction Screen
Step 3: Click PCISA-9102.
Step 4: A new screen with a list of available drivers appears (Figure 7-2).
Figure 7-2: Available Drivers
Step 5: Select the driver to install from the list in Figure 7-2. Detailed driver installation
instructions follow below. Step 0:
Page 143
PCISA-9102 Half-Size CPU Card
7.3 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Insert the CD into the system that contains the PCISA-9102 board. Open the
1-INF directory and locate the icon for the infinst_autol.exe installation file.
Once located, use the mouse to double click the icon.
Step 2: The “InstallShield Wizard Preparation Screen” in Figure 7-3 appears.
Figure 7-3: InstallShield Wizard Preparation Screen
Step 3: The “Welcome” window in Figure 7-4 appears next.
Figure 7-4: Welcome Screen
Page 144
PCISA -9102 Half-Size CPU Card
Step 4: Click “NEXT” and the license agreement shown in Figure 7-5 appears.
Figure 7-5: License Agreement
Step 5: Agree to the license terms by clicking “YES”. The “Readme” in Figure 7-6
appears.
Figure 7-6: Readme Information
Step 6: Click “YES”. The driver is installed on the computer. After the installation is
Page 145
PCISA-9102 Half-Size CPU Card
complete, the installation complete screen shown in Figure 7-7 appears. Select
the preferred option and click “FINISH” to complete the installation process.
Step 0:
Figure 7-7: Restart the Computer
7.4 VGA Driver
To install the VGA driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive)
and double-click the win2k_xp1420.exe installation file.
Step 3: The Starting Install Shield Wizard appears (Figure 7-8).
Page 146
PCISA -9102 Half-Size CPU Card
Figure 7-8: Starting Install Shield Wizard Screen
Step 4: The Preparing Setup window appears next (Figure 7-9).
Figure 7-9: Preparing Setup Screen
Page 147
PCISA-9102 Half-Size CPU Card
Step 5: A Welcome screen shown in Figure 7-10 appears. Click NEXT to continue the
installation.
Figure 7-10: VGA Driver Installation Welcome Screen
Step 6: A license agreement shown in Figure 7-11 appears. Read through the license
agreement.
Figure 7-11: VGA Driver License Agreement
Page 148
PCISA -9102 Half-Size CPU Card
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
the “YES” button (Figure 7-11). The installation notice shown in Figure 7-12
appears.
Figure 7-12: VGA Driver Installing Notice
Step 8: After the driver installation process is complete, a confirmation screen shown in
Figure 7-13 appears.
Figure 7-13: VGA Driver Installation Complete
Step 9: The confirmation screen shown in Figure 7-13 allows user to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once
decided when to restart the computer, click the “FINISH” button. Step 0:
Page 149
PCISA-9102 Half-Size CPU Card
7.5 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 7-14).
Figure 7-14: Access Windows Control Panel
Step 2: Double click the System icon (Figure 7-15).
Page 150
PCISA -9102 Half-Size CPU Card
Figure 7-15: Double Click the System Icon
Step 3: Double click the Device Manager tab (Figure 7-16).
Figure 7-16: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 7-17).
Page 151
PCISA-9102 Half-Size CPU Card
Figure 7-17: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Step 6: The Device Driver Wizard appears (Figure 7-18). Click NEXT to continue.
Page 152
PCISA -9102 Half-Size CPU Card
Figure 7-18: Search for Suitable Driver
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-19).
Click NEXT to continue.
Figure 7-19: Locate Driver Files
Page 153
PCISA-9102 Half-Size CPU Card
Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx
Drivers” directory (Figure 7-20) in the location browsing window, where “X:\” is
the system CD drive.
Figure 7-20: Location Browsing Window
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
continue. The driver is installed.Step 0:
7.6 Intel® Matrix Storage Manager Driver Installation
To install the Intel® Matrix Storage Manager driver, please follow the steps below:
Step 1: Select SATA from the list in Figure 7-2.
Step 2: A new window opens (Figure 7-21).
Page 154
PCISA -9102 Half-Size CPU Card
Figure 7-21: SATA RAID Driver Installation Program
Step 3: Double-click the INTEL folder.
Step 4: Double-click the iata62_cd.exe program icon in Figure 7-22.
Page 155
PCISA-9102 Half-Size CPU Card
Figure 7-22: SATA RAID Setup Program Icon
Step 5: Figure 7-23 shows the InstallShield Wizard preparing to guide the user through
the rest of the process.
Figure 7-23: InstallShield Wizard Setup Screen
Page 156
PCISA -9102 Half-Size CPU Card
Step 6: Figure 7-24 shows the Matrix Storage Manager software configuring the
installation process.
Figure 7-24: Matrix Storage Manager Setup Screen
Step 7: Figure 7-25 shows the Matrix Storage Manager welcome screen.
Figure 7-25: Matrix Storage Manager Welcome Screen
Step 8: Click NEXT and a warning appears (Figure 7-26). Read the warning carefully and
Page 157
PCISA-9102 Half-Size CPU Card
decide whether or not to continue the installation process.
Figure 7-26: Matrix Storage Manager Warning Screen
Step 9: Click NEXT and a license agreement appears (Figure 7-27).
Figure 7-27: Matrix Storage Manager License Agreement
Step 10: Read the license agreement. To accept the terms and conditions stipulated in
the license agreement shown, click YES and the Readme information file shown
in Figure 7-28 appears.
Page 158
PCISA -9102 Half-Size CPU Card
Figure 7-28: Matrix Storage Manager Readme File
Step 11: Read the Readme file information and click NEXT.
Step 12: After the driver installation process is complete, a confirmation screen appears
(Figure 7-29).
Figure 7-29: Matrix Storage Manager Setup Complete
Page 159
PCISA-9102 Half-Size CPU Card
Step 13: The confirmation screen offers the option of restarting the computer now or later.
For the settings to take effect, the computer must be restarted. Click FINISH to
restart the computer. Step 0:
Page 160
PCISA -9102 Half-Size CPU Card
Appendix
A
A BIOS Configuration
Options
Page 161
PCISA-9102 Half-Size CPU Card
A.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 6.
System Overview ................................................................................................ 103
System Time [xx:xx:xx] ...................................................................................... 104
System Date [xx/xx/xx] ....................................................................................... 104
ATA/IDE Configurations [Compatible].............................................................. 107
Legacy IDE Channels [SATA Pri, PATA Sec]................................................... 108
IDE Master and IDE Slave .................................................................................. 108
Type [Auto] .......................................................................................................... 109
ZIP ....................................................................................................................... 110
LS-120 .................................................................................................................. 110
LBA/Large Mode [Auto]...................................................................................... 110
Block (Multi Sector Transfer) [Auto] ................................................................. 110
PIO Mode [Auto].................................................................................................. 111
DMA Mode [Auto]................................................................................................ 111
S.M.A.R.T [Auto].................................................................................................. 112
32Bit Data Transfer [Enabled] ........................................................................... 113
Floppy A............................................................................................................... 114
Serial Port1 Address [3F8/IRQ4] ....................................................................... 115
Serial Port2 Address [2F8/IRQ3] ....................................................................... 115
Serial Port2 Mode [Normal]................................................................................ 115
Parallel Port Address [378] ................................................................................ 116
Parallel Port Mode [Normal]............................................................................... 116
Parallel Port IRQ [IRQ7]...................................................................................... 117
CPU FAN Mode Setting [Manual Mode] ............................................................ 118
Target CPU Temp Value ..................................................................................... 118
CPU Temp Tolerance Value ............................................................................... 118
CPU FAN StartUp Value ..................................................................................... 118
CPU FAN Stop Value .......................................................................................... 118
CPU FAN StopTime Value.................................................................................. 118
Page 162
PCISA -9102 Half-Size CPU Card
CPU FAN TargetSpeed Value ............................................................................ 119
CPU Temp Tolerance Value ............................................................................... 119
CPU Fan PWM Control [250].............................................................................. 119
Remote Access [Disabled]................................................................................. 120
Serial Port Number ............................................................................................. 120
Serial Port Mode.................................................................................................. 120
Redirection after BIOS POST............................................................................. 120
Terminal Type...................................................................................................... 120
Serial Port Number [COM1] ............................................................................... 121
Base Address, IRQ [3F8h,4]............................................................................... 121
Serial Port Mode [115200 8,n,1]......................................................................... 121
Redirection After BIOS POST [Always] ............................................................ 122
Terminal Type [ANSI] ......................................................................................... 122
USB Configuration.............................................................................................. 123
USB Devices Enabled......................................................................................... 123
USB Function [8 USB Ports].............................................................................. 123
USB 2.0 Controller [Enabled]............................................................................. 124
Legacy USB Support [Enabled]......................................................................... 124
USB2.0 Controller Mode [HiSpeed]................................................................... 124
IRQ#...................................................................................................................... 125
DMA Channel# [Available] ................................................................................. 126
Reserved Memory Size [Disabled] .................................................................... 127
Quick Boot [Enabled] ......................................................................................... 128
Quiet Boot [Enabled] .......................................................................................... 128
AddOn ROM Display Mode [Force BIOS] ......................................................... 129
Bootup Num-Lock [On] ...................................................................................... 129
Boot From LAN Support [Disabled] .................................................................. 130
Change Supervisor Password........................................................................... 132
Change User Password...................................................................................... 132
Memory Hole [Disabled]..................................................................................... 134
Internal Graphics Mode Select [Enable, 8MB] ................................................. 134
Page 163
PCISA-9102 Half-Size CPU Card
DVMT Mode Select [DVMT Mode]...................................................................... 134
DVMT/FIXED Memory [128MB] .......................................................................... 135
Boot Display Device [Auto]................................................................................ 135
Flat Panel Type [1024x768 18b]......................................................................... 135
Azalia/AC97 Selection [Azalia] .......................................................................... 136
Onboard BCM5787 Port n [Enabled]................................................................. 137
Power Supply Mode [BY HARDWARE]............................................................. 137
Power Button Mode ............................................................................................ 138
Restore on AC Power Loss................................................................................ 138
Suspend Mode .................................................................................................... 138
RTC Resume........................................................................................................ 138
RI Resume ........................................................................................................... 138
Resume On KeyBoard/Mouse ........................................................................... 138
Save Changes and Exit ...................................................................................... 139
Discard Changes and Exit ................................................................................. 139
Discard Changes................................................................................................. 139
Load Optimal Defaults........................................................................................ 139
Load Failsafe Defaults........................................................................................ 140
Page 164
PCISA -9102 Half-Size CPU Card
Appendix
B
B Terminology
Page 165
PCISA-9102 Half-Size CPU Card
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®
in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects storage
devices including hard disks and CD-ROM drives to a computer.
APM
The Advanced Power Management (APM) application program
interface (API) enables the inclusion of power management in the
BIOS.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes digital
audio data on the system.
CompactFlash®
CompactFlash® is a solid-state storage device. CompactFlash®
devices use flash memory in a standard size enclosure. Type II is
thicker than Type I, but a Type II slot can support both types.
CMOS
Complimentary metal-oxide-conductor is an integrated circuit used in
chips like static RAM and microprocessors.
Page 166
PCISA -9102 Half-Size CPU Card
COM
COM refers to serial ports. Serial ports offer serial communication to
expansion devices. The serial port on a personal computer is usually a
male DB-9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to analog
signals.
DDR
Double Data Rate refers to a data bus transferring data on both the
rising and falling edges of the clock signal.
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the system
memory.
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
DIO
The digital inputs and digital outputs are general control signals that
control the on/off circuit of external devices or TTL devices. Data can be
read or written to the selected address to enable the DIO functions.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
FSB
The Front Side Bus (FSB) is the bi-directional communication channel
between the processor and the Northbridge chipset.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
GPIO
General purpose input
HDD
Hard disk drive (HDD) is a type of magnetic, non-volatile computer
storage device that stores digitally encoded data.
ICH
The Input/Ouput Controll Hub (ICH) is an Intel® Southbridge chipset.
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
Page 167
PCISA-9102 Half-Size CPU Card
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
The Level 2 Cache (L2 Cache) is an external processor memory cache.
LCD
Liquid crystal display (LCD) is a flat, low-power display device that
consists of two polarizing plates with a liquid crystal panel in between.
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
MAC
The Media Access Control (MAC) protocol enables several terminals or
network nodes to communicate in a LAN, or other multipoint networks.
PCIe
PCI Express (PCIe) is a communications bus that uses dual data lines
for full-duplex (two-way) serial (point-to-point) communications between
the SBC components and/or expansion cards and the SBC chipsets.
Each line has a 2.5 Gbps data transmission rate and a 250 MBps
sustained data transfer rate.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
RAM
Random Access Memory (RAM) is volatile memory that loses data
when power is lost. RAM has very fast data transfer rates compared to
other storage like hard drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The
SATA bus has transfer speeds up to 1.5 Gbps and the SATA II bus has
data transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Page 168
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers
PCISA -9102 Half-Size CPU Card
to automatic status checking technology implemented on hard disk
drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the
system’s serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates, while
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system
developed by IBM.
Page 169
PCISA-9102 Half-Size CPU Card
Appendix
C
C Watchdog Timer
Page 170
PCISA -9102 Half-Size CPU Card
NOTE:
The following discussion applies to DOS environment.
IEI support is
contacted or the IEI website visited for specific drivers for more
sophisticated operating systems, e.g., Windows and Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer either performs a hardware reset (cold boot) or a Non-Maskable Interrupt
(NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table C-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. While the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the Watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 171
PCISA-9102 Half-Size CPU Card
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system resets.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;No, restart the application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 172
;is the application over?
PCISA -9102 Half-Size CPU Card
Appendix
D
D Address Mapping
Page 173
PCISA-9102 Half-Size CPU Card
D.1 IO Address Map
I/O address
Description
Range
000-01F
DMA Controller
020-021
Interrupt Controller
040-043
System time
060-06F
Keyboard Controller
070-07F
System CMOS/Real time Clock
080-09F
DMA Controller
0A0-0A1
Interrupt Controller
0C0-0DF
DMA Controller
0F0-0FF
Numeric data processor
1F0-1F7
Primary IDE Channel
2E8-2EF
Serial Port 4 (COM4)
2F8-2FF
Serial Port 2 (COM2)
378-37F
Parallel Printer Port 1 (LPT1)
3B0-3BB
Intel 910GMLE Graphics Controller
3C0-3DF
Intel 910GMLE Graphics Controller
3E8-3EF
Serial Port 3 (COM3)
3F6-3F6
Primary IDE Channel
3F7-3F7
Standard floppy disk controller
3F8-3FF
Serial Port 1 (COM1)
Table D-1: IO Address Map
D.2 1st MB Memory Address Map
Memory address
Description
00000-9FFFF
System memory
A0000-BFFFF
VGA buffer
F0000-FFFFF
System BIOS
1000000-
Extend BIOS
Table D-2: 1st MB Memory Address Map
Page 174
PCISA -9102 Half-Size CPU Card
D.3 IRQ Mapping Table
IRQ
Description
IRQ
Description
IRQ0
System Timer
IRQ8
RTC clock
IRQ1
Keyboard
IRQ9
ACPI
IRQ2
Available
IRQ10
COM 4
IRQ3
COM2
IRQ11
COM 3
IRQ4
COM1
IRQ12
PS/2 mouse
IRQ5
SMBus Controller
IRQ13
FPU
IRQ6
FDC
IRQ14
Primary IDE
IRQ7
Parallel port
IRQ15
Secondary IDE
Table D-3: IRQ Mapping Table
D.4 DMA Channel Assignments
Channel
Function
0
Available
1
Available
2
Floppy disk (8-bit transfer)
3
Available
4
Cascade for DMA controller 1
5
Available
6
Available
7
Available
Table D-4: DMA Channel Assignments
Page 175
PCISA-9102 Half-Size CPU Card
Appendix
E
E Compatibility
Page 176
PCISA -9102 Half-Size CPU Card
NOTE:
The compatible items described here have been tested by the IEI R&D
team and found to be compatible with the PCISA-9102.
E.1 Compatible Processors
The following Socket 478 90nm processors have been successfully tested on the
PCISA-9102.
CPU
Model Number
Frequency
FSB
Intel® Pentium® M
745
1.80 GHz
400 MHz
Intel® Pentium® M
725
1.60 GHz
400 MHz
Intel® Celeron® M
373
1.00 GHz
400 MHz
Intel® Celeron® M
370
1.50 GHz
400 MHz
Intel® Celeron® M
320
1.30 GHz
400 MHz
E.2 Compatible Memory Modules
NOTE:
The memory modules listed below have been tested on the
PCISA-9102 other memory modules that comply with the specifications
may also work on the PCISA-9102 but have not been tested.
The following memory modules have been successfully tested on the PCISA-9102.
Page 177
PCISA-9102 Half-Size CPU Card
Manufacturer
Model No.
Capacity
Speed
Kingston
KVR533D2N4/512
512 MB
533 MHz
KingBOX
DDR2 512MB 533MHz
512 MB
533 MHz
ADATA
DDR2 667(5) 512MX8
512 MB
667 MHz
Corsair
V512MB533D2
512 MB
533 MHz
UMAX
DIMM, 512MB, DDRII800, 64X8
512 MB
800 MHz
Unigen
UG64T6400L8DU-6AL
512 MB
667 MHz
Transcend
1GB DDR2 667
1 GB
667 MHz
Transcend
2GB DDR2 800
2 GB
800 MHz
Apacer
512MB UNB PC2-5300 CL5
512 MB
667 MHz
PK
512 MB DDR2 800MHz
512 MB
800 MHz
TwinMOS
8D25JK-TT
512 MB
800 MHz
DSL
512MB DDR2 800MHz CL5
512 MB
800 MHz
Page 178
PCISA -9102 Half-Size CPU Card
Appendix
F
F Hazardous Materials
Disclosure
Page 179
PCISA-9102 Half-Size CPU Card
F.1 Hazardous Material Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 180
PCISA -9102 Half-Size CPU Card
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
X
O
O
O
O
X
Display
X
O
O
O
O
X
Printed Circuit
X
O
O
O
O
X
Metal Fasteners
X
O
O
O
O
O
Cable Assembly
X
O
O
O
O
X
Fan Assembly
X
O
O
O
O
X
Power Supply
X
O
O
O
O
X
O
O
O
O
O
Board
Assemblies
Battery
O
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
Page 181
PCISA-9102 Half-Size CPU Card
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些
元件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
X
O
O
O
O
X
显示
X
O
O
O
O
X
印刷电路板
X
O
O
O
O
X
金属螺帽
X
O
O
O
O
O
电缆组装
X
O
O
O
O
X
风扇组装
X
O
O
O
O
X
电力供应组装
X
O
O
O
O
X
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 182
PCISA -9102 Half-Size CPU Card
G Index
Page 183
PCISA-9102 Half-Size CPU Card
socket ....................................................45
A
airflow ........................................................89
AMI BIOS.....................................................7
anti-static precautions..........................35, 71
anti-static pad ..................................35, 71
anti-static wristband.........................35, 71
handling ...........................................35, 71
self-grounding..................................35, 71
ASKIR interface .........................................54
AT power select jumper .............................81
location ..................................................81
settings ..................................................81
ATX power ...................................................8
ATX power supply enable connector .........43
location and pinouts ..............................43
Audio Codec ’97 ........................................20
B
CF card setup jumper ................................82
location ..................................................82
settings ..................................................82
chassis .......................................... 43, 67, 89
backplane installation ............................89
installation..............................................89
Clear CMOS.......................................... 6, 80
clear CMOS jumper ...................................83
location ..................................................83
settings ..................................................83
CMOS ........................................................83
clear CMOS jumper ...............................83
codec .........................................................20
AC’97.....................................................20
COM 2
COM 2 function select ...........................84
COM 2 function select jumper ...................84
location ..................................................84
settings ..................................................84
backplane ..................................................89
CompactFlash............................................45
installation..............................................89
socket location and pinouts ...................45
BIOS 27, 101, 102, 103, 104, 105, 106, 107,
connectors, external
108, 109, 113, 114, 117, 119, 120, 122,
CRT connector.......................................67
123, 125, 127, 128, 129, 130, 131, 132,
LAN connector.......................................68
133, 136, 137, 138, 139
RJ-45 connector ....................................68
USB port ................................................69
C
cables ........................................................90
dual port USB ........................................93
CF card ......................................................45
location and pinouts ..............................45
setup jumper..........................................82
Page 184
connectors, pinouts and location
14-pin serial port....................................64
ATX power supply enable......................43
audio......................................................44
COM 1 serial port ..................................63
CompactFlash .......................................45
digital input/output .................................47
PCISA-9102 Half-Size CPU Card
fan..........................................................48
Digital I/O .................................................5, 7
floppy disk .............................................49
dimensions.................................................10
front panel..............................................51
board .....................................................10
IDE.........................................................52
external peripheral interface connector
infrared interface ...................................54
panel..................................................12
internal USB ..........................................65
DIMM .........................................................78
keyboard................................................55
installation..............................................78
LCD backlight ........................................56
specifcations..........................................78
LVDS LCD .............................................57
DMA controller ........................................ 175
parallel port............................................58
Drivers
power.....................................................59
Intel® Matrix Storage Manager ........... 154
SATA......................................................60
dual port USB cable...................................93
SDVO ....................................................61
serial port (COM 1)................................63
cooling .......................................................89
airflow ....................................................89
cooling fan .............................48, 76, 78, 118
cooling kit installation.................................76
CPU
cooling fan .............................................76
heat sink ................................................76
installation..............................................74
CPU card ...................................................90
E
electrostatic discharge ........................ 35, 71
Enhanced Hardware Monitor .....................29
Ethernet .....................................................96
RJ-45 cable connector ..........................96
external peripheral interface ......................96
connection .............................................96
connectors .............................................96
F
installation..............................................90
CPU frequency ......................................6, 80
CPU Frequency Setup
fan connector .............................................48
location and pinouts...............................48
settings ..................................................85
FDD..........................................................114
CPU Frequency Setup jumper...................85
floppy disk connector .................................49
CRT connector...........................................67
location and pinouts...............................49
CRT monitor...............................................97
floppy disk drive .........................................49
front panel ..................................................51
D
DB-15 connector........................................97
DDR2 .............................................3, 5, 7, 41
Page 2
Front panel............................................ 5, 42
front side bus ...............................................2
FSB ......................................................... 106
PCISA -9102 Half-Size CPU Card
H
K
heat sink ....................................................76
keyboard/mouse ........................................55
keyboard/mouse connector .......................55
I
ICH6-M ........................................................7
location and pinouts...............................55
L
IDE device .................................................91
connector...............................................91
LAN connection..........................................96
IDE flat cable .........................................91
LAN connector ...........................................68
IDE flat cable .............................................91
LCD backlight.................................. 5, 42, 56
IDE interface ..............................................21
LCD voltage .......................................... 6, 80
infrared interface........................................54
LPC bus .....................................................26
Amplitude Shift Key Infrared..................54
LPC interface ...................................... 22, 28
ASKIR....................................................54
LVDS display....................................... 86, 87
Serial Infrared........................................54
resolution ...............................................87
SIR.........................................................54
voltage select.........................................86
infrared interface connector.......................54
LVDS panel resolution selection jumper ....87
location and pinouts ..............................54
LVDS resolution selection jumper
installation checklist ...................................73
location ..................................................88
Intel 910GMLE.........................................174
settings ..................................................87
Intel® 910GMLE 7, 12, 14, 15, 16, 17, 18, 19
LVDS voltage selection jumper..................86
IrDA.......................................................... 115
location ..................................................87
settings ..................................................86
J
M
jumper........................................................80
AT power select .....................................81
memory module installation .......................78
CF card setup........................................82
memory support .........................................15
clear CMOS...........................................83
COM 2 function select ...........................84
jumper configuration..............................80
LVDS resolution selection .....................87
LVDS voltage selection .........................86
N
Northbridge ..................................................7
P
panel resolution............................................6
Page 3
PCISA-9102 Half-Size CPU Card
parallel port ................................ 29, 116, 117
SDVO connector ........................................61
parallel port connector ...............................58
location and pinouts...............................61
location and pinouts ..............................58
serial port connector ..................................63
PCI interface ..............................................22
location and pinouts...............................63
PCIe bus ....................................................25
CPU ...........................................................85
peripheral device cables............................90
SIR interface ..............................................54
Power Button Mode .................................137
socket P CPU
power connector ........................................59
installation..............................................74
location and pinouts ..............................59
Super I/O chipset ................................ 26, 27
power supply..............................................59
system voltages ............................... 117, 118
AT power select jumper.........................81
T
PS/2 .........................................................175
PS/2 cable .................................................55
temperature..............................................117
R
real time clock............................................23
RJ-45 .......................................42, 67, 68, 69
RJ-45 connection.......................................96
single connector ....................................96
RJ-45 connector ........................................68
RoHS ...........................................................3
RS-232.......................................................63
COM 1 location and pinouts ..................63
connector location and pinouts..............63
serial port devices .................................63
RS-232 serial port devices ........................63
S
U
unpacking...................................................35
unpacking checklist ...............................36
unpacking precautions...........................35
USB............................... 2, 93, 122, 123, 124
cable
dual port ............................................93
cable ......................................................93
cable connection....................................93
connectors .............................................93
controller................................................24
external USB device connection ...........98
USB 2.0..................... 3, 6, 7, 43, 65, 67, 124
USB cable
SATA ..............................................2, 6, 7, 60
dual port.................................................93
controller................................................24
USB device connection..............................98
SATA drive .................................................92
single connector ....................................98
cables ....................................................92
USB port ....................................................69
connection .............................................92
power cable ...........................................92
Page 4
PCISA -9102 Half-Size CPU Card
V
VGA ...........................................................97
connection .............................................97
W
VGA monitor ..............................................97
warranty validation .....................................73
Page 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement