USER`S MANUAL
USER’S MANUAL
Mini-Split Air Conditioner
YEHJZH009-24BAM1ABX
YEHJZH009-24BAM1AKX
Read this manual before installation and operation
Make sure that it is well kept for later reference
If you have lost the Owner’s Manual, please sent email to
[email protected] for electronic version.
UYHJZHAMQ-140505
Content
Operation Notices
Precautions............................................................................................................ 1
Parts Name............................................................................................................ 6
Screen Operation Guide
Buttons on remote controller..................................................................................7
Introduction for icons on display screen.................................................................7
Introduction for buttons on remote controller......................................................... 8
Introduction for special function............................................................................13
Operation guide................................................................................................... 15
Replacement of batteries in remote controller......................................................15
Emergency operation .......................................................................................... 16
Maintenance
Clean and Maintenance........................................................................................16
Malfunction
Malfunction analysis ............................................................................................ 19
Installation Notice
Installation dimension diagram ............................................................................ 23
Tools for installation............................................................................................. 24
Selection of installation location .......................................................................... 24
Requirements for electric connection .................................................................. 25
Installation
Installation of indoor unit...................................................................................... 26
Check after installation ........................................................................................ 31
Test and operation
Test operation.......................................... ............................................................31
Attachment
Configuration of connection pipe ......................................................................... 32
Pipe expanding method ....................................................................................... 34
Wired Controller (Optional).................................................................................. 35
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
R410A(R32/125: 50/50): 1975
Precautions
WARNING
Operation and Maintenance
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Do not connect air conditioner to multi-purpose socket.
Otherwise, it may cause fire hazard.
Do disconnect power supply when cleaning air
conditioner. Otherwise, it may cause electric shock.
.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Do not wash the air conditioner with water to avoid
electric shock.
Do not spray water on indoor unit. It may cause electric
shock or malfunction.
After removing the filter, do not touch fins to avoid injury.
Do not use fire or hair dryer to dry the filter to avoid
deformation or fire hazard.
1
Precautions
WARNING
Maintenance must be performed by qualified
professionals. Otherwise, it may cause personal injury
or damage.
Do not repair air conditioner by yourself. It may cause
electric shock or damage. Please contact dealer when
you need to repair air conditioner.
Do not extend fingers or objects into air inlet or air
outlet. It may cause personal injury or damage.
Do not block air outlet or air inlet. It may cause
malfunction.
Do not spill water on the remote controller, otherwise the
remote controller may be broken.
When below phenomenon occurs, please turn off air
conditioner and disconnect power immediately, and then
contact the dealer or qualified professionals for service.
Ɣ Power cord is overheating or damaged.
Ɣ There’s abnormal sound during operation.
Ɣ Circuit break trips off frequently.
Ɣ Air conditioner gives off burning smell.
Ɣ Indoor unit is leaking.
If the air conditioner operates under abnormal conditions,
it may cause malfunction, electric shock or fire hazard.
When turning on or turning off the unit by emergency
operation switch, please press this switch with an insulating
object other than metal.
Do not step on top panel of outdoor unit, or put heavy
objects. It may cause damage or personal injury.
2
Precautions
WARNING
Attachment
Installation must be performed by qualified professionals.
Otherwise, it may cause personal injury or damage.
Must follow the electric safety regulations when installing
the unit.
According to the local safety regulations, use qualified
power supply circuit and circuit break.
Do install the circuit break. If not, it may cause malfunction.
An all-pole disconnection switch having a contact separation
of at least 3mm in all poles should be connected in fixed
wiring.
Including an circuit break with suitable capacity, please
note the following table. Air switch should be included
magnet buckle and heating buckle function, it can protect
the circuit-short and overload.
Air Conditioner should be properly grounded. Incorrect
grounding may cause electric shock.
Don't use unqualified power cord.
Make sure the power supply matches with the
requirement of air conditioner. Unstable power supply or
incorrect wiring or malfunction. Please install proper power
supply cables before using the air conditioner.
Properly connect the live wire, neutral wire and
grounding wire of power socket.
Be sure to cut off the power supply before proceeding
any work related to electricity and safety.
3
Precautions
WARNING
Do not put through the power before finishing installation.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
The temperature of refrigerant circuit will be high, please
keep the interconnection cable away from the copper
tube.
The appliance shall be installed in accordance with
national wiring regulations.
Installation must be performed in accordance with the
requirement of NEC and CEC by authorized personnel
only
The air conditioner is the first class electric appliance. It
must be properly grounding with specialized grounding
device by a professional. Please make sure it is always
grounded effectively, otherwise it may cause electric shock.
The yellow-green wire in air conditioner is grounding
wire, which can't be used for other purposes.
The grounding resistance should comply with national
electric safety regulations.
The appliance must be positioned so that the plug is
accessible.
All wires of indoor unit and outdoor unit should be
connected by a professional.
If the length of power connection wire is insufficient, please
contact the supplier for a new one. Avoid extending the
wire by yourself.
4
Precautions
WARNING
For the air conditioner with plug, the plug should be
reachable after finishing installation.
For the air conditioner without plug, an circuit break
must be installed in the line.
If you need to relocate the air conditioner to another
place, only the qualified person can perform the work.
Otherwise, it may cause personal injury or damage.
Select a location which is out of reach for children and
far away from animals or plants.If it is unavoidable,
please add the fence for safety purpose.
The indoor unit should be installed close to the wall.
Instructions for installation and use of this product are
provided by the manufacturer.
Working temperature range
Maximum cooling
Maximum heating
Indoor side DB/WB(ć )
32/23
27/-
Outdoor side DB/WB(ć )
43/26
24/18
NOTICE:
Ɣ The operating temperature range (outdoor temperature) for cooling is -15 ~43 ;
Heating temperature range for the model without electric heating belt for chassis
is -15 ~43
Heating temperature range for the model with electric heating belt
for chassis is -20 ~43 .
5
Parts Name
Indoor Unit
air inlet
aux.button
horizontal louver
air outlet
cooling
indicator
power
indicator
receiver
window
display
heating
indicator
temp.
indicator
drying
indicator
(Display content or position may be different from above
graphics, please refer to actual products)
remote controller
NOTICE:
Actual product may be different from above graphics, please refer to actual
products.
6
Buttons on remote controller
1 ON/OFF button
2 FAN button
3 MODE button
4 +/- button
5 TURBO button
6
button
2
2
5
6
4
4
11
3
9
7
3
8
1
13
10
12
14
16
7
8 CLOCK button
1
15
9 TIMER ON/
TIMER OFF button
10 TEMP button
11
(before opening cover
(after opening cover
button
/
button
12 I FEEL button
1 ON/OFF button
13 LIGHT button
2 FAN button
14 X-FAN button
3 MODE button
15 QUIET button
4 +/- button
16 SLEEP button
Introduction for icons on display screen
I feel
Quiet
Set fan speed
Turbo mode
Send signal
Healthy mode
Scavenging functions
8ć(46̧) heating function
Operation mode
Auto mode
Cool mode
Set temperature
X-FAN function
Dry mode
Fan mode
Heat mode
Set time
TIMER ON /TIMER OFF
Clock
Sleep mode
Child lock
Up & down swing
Left & right swing
Light
Temp. display type
: Set temp.
: Indoor ambient temp.
: Outdoor ambient temp.
7
Introduction for buttons on remote controller
Note:
Ɣ After putting through the power, the air conditioner will give out a sound.
Operation indictor " " is ON (red indicator). After that, you can operate the air
conditioner by using remote controller.
ƔUnder on status, pressing the button on the remote controller, the signal icon " "
on the display of remote controller will blink once and the air conditioner will give
out a “de” sound, which means the signal has been sent to the air conditioner.
Ɣ8QGHURff status, set temperature and clock icon will be displayed on the display
of remote controller (If timer on, timer off and light functions are set, the corresponding icons will be displayed on the display of remote controller at the same
time); Under on status, the display will show the corresponding set function icons.
1
ON/OFF button
Press this button, the unit will be turned on, press it once more, the unit will be turned off. Sleep function will be canceled, while unit off.
2
FAN button
Press this button, Auto, Low, Medium-low, Medium, Medium-high, High speed can
be circularly selected. After powered on, Auto fan speed is default. Under DRY
mode, Low fan speed only can be set up.
ATUO
Low fan
Medium-low fan
Note: It’s Low fan speed
under Dry mode.
Medium fan
Medium-high fan
High fan
Note: If matching with smart zone controller for operation, under auto fan speed, the
fan speed display on smart zone controller will always be maintained at “auto high fan”.
3
MODE button
Press this button, Auto, Cool, Dry, Fan, Heat mode can be selected circularly. Auto
mode is default while power on. Under Auto mode, the temperature will not be displayed; Under Heat mode, the initial value is 28ć(82̧); Under other modes, the
initial value is 25ć(77̧).
AUTO
COOL
DRY
FAN
HEAT
(only for cooling and heating unit. As for cooling only unit, it won’t have any action
when it receives the signal of heating operation.)
4
+/- button
Presetting temperature can be increased. Press this button, the temperature can be
set up, continuously press this button and hold for two seconds, the relative contents
can quickly change, until unhold this button and send the order that the ć(̧) signal
will be displayed all the time. The temperature adjustment is unavailable under the
Auto mode, but the order can be sent if pressing this button. Temperature of Celsius
degree setting: 16-30; for Fahrenheit degree setting: 61-86.
8
Introduction for buttons on remote controller
Presetting temperature can be decreased. Press this button, the temperature can
be set up, continuously press this button and hold for two seconds, the relative contents can quickly change, until unhold this button and send the order that the Ƈ
(Ɖ) signal will be displayed all the time. The temperature adjustment is unavailable
under the Auto mode, but the order can be sent by if pressing this button.
5
TURBO button
Under Cool or Heat mode, press this button can turn on or turn off the Turbo function.
After the Turbo function turned on, the signal of Turbo will display. The signal will
be automatically cancelled if changing the mode or fan speed.
6
button
Press this button to set left & right swing angle cycling as below:
OFF
7
button
Press this button to set swing angle, which circularly changes as below:
OFF
This remote controller is universal. If it receives threes kinds of following status, the
swing angle will remain original.
If guide louver is stopped when it is swinging up and down, it will remian its present
position.
indicates guide louver swings back and forth in the five places, as shown in the figure.
8
CLOCK button
Press this button, the clock can be set up, signal blink and display. Within 5 seconds,
the value can be adjusted by pressing + or - button, if continuously press this button for 2
seconds above, in every 0.5 seconds, the value on ten place ofMinutewill be increased 1.
During blinking, repress the Clock button or Confirm button, signal will be constantly
displayed and it denotes the setting succeeded. After powered on, 12:00 is defaulted to
display and signal will be displayed. If there is signal be displayed that denotes
the current time value is Clock value, otherwise is Timer value.
9
TIMER ON/TIMER OFF button
Timer On setting: Sign al “ON” will blink and display, signal will conceal, the numerical section will become the timer on setting status. During 5 seconds blink, by
pressing + or - button to adjust the time value of numerical section, every press of
that button, the value will be increased or decreased 1 minute. Hold pressing + or -
9
Introduction for buttons on remote controller
button, 2 seconds later, it quickly change, the way of change is: During the initial
2.5 seconds, ten numbers change in the one place of minute, then the one place
is constant, ten numbers change in the tens place of minu te at 2.5 seconds speed
and carry. During 5s blink, press the Timer button, the timer setting succeeds. The
Timer On has been set up, repress the timer button, the Timer On will be canceled.
Before sett ing the Timer, please adjust the Clock to the current actual time.
One press this key to enter into TIMER OFF setup, in which case the TIMER OFF
icon will blink. The method of setting is the sameas for TIMER ON.
10
TEMP button
Press this button, you can see indoor set temperature, indoor ambient temperature
or outdoor ambient temperature on indoor unit’s display. The setting on remote controller is selected circularly as below:
no display
When selecting " " with remote controller or no display, temperature indicator on
indoor unit displays set temperature; When selecting " " with remote controller,
temperature indicator on indoor unit displays indoor ambient temperature; When
selecting " " with remote controller, temperature indicator on indoor unit displays
outdoor ambient temperature. 3s later it will return to the setting temprature or it
depends on the other received signal within 3s.
Attention: When displaying the outdoor ambient, the displaying range is 0-60Ƈ
When it goes beyond the range, it keeps the threshold data (the smallest—0Ƈ
and the largest 60Ƈ).
Warm tips: When operating buttons on the cover please make sure the cover is
closed completely.
11
/
button
Press this button to achieve the on and off of healthy and scavenging functions in
operation status. Press this button for the first time to start scavenging function;
LCD displays " ". Press the button for the second time to start healthy and scavenging functions simultaneously; LCD displays " " and " ". Press this button
for the third time to quit healthy and scavenging functions simultaneously. Press the
button for the fourth time to start healthy function; LCD display " ". Press this button again to repeat the operation above.
NOTE: This function is applicable to partial of models.
12
I FEEL button
Press this button once, to turn on the I FEEL function, then the figure of "I FEEL"
will be displayed, after every press of other function button, every 200ms to send
I FEEL once, after this function started, the remote controller will send temperature
to the main un it in every 10 minutes. When repress this button, this function will be
turned off.
10
Introduction for buttons on remote controller
13
LIGHT button
Press this button at unit On or Off status, Light On and Light Off can be set up.
After powered on, Light On is defaulted.
14
X-FAN button
Pressing X-FAN button in COOL or DRY mode, the icon
is displayed and the
indoor fan will continue operation for 2 minutes in order to dry the indoor unit even
though you have turned off the unit. After energization, X-FAN OFF is defaulted.
X-FAN is not available in AUTO, FAN or HEAT mode.
15
QUIET button
Press this button, the Quiet status is under the Auto Quiet mode (display " "
and "Auto" signal) and Quiet mode (display " " singal) and Quiet OFF (there
is no signal of " " displayed), after powered on, the Quiet OFF is defaulted.
Under the Quiet mode (Display "
" signal).
16
SLEEP button
Press this button, can select Sleep 1 (
), Sleep 2 (
), Sleep 3 (
) and
cancel the Sleep, circulate between these, after electrified, Sleep Cancel is defaulted.
Sleep 1 is Sleep mode 1, in Cool, Dehumidify modes: sleep status after run for
one hour, the main unit setting temperature will increase 1Ƈ, 2 hours, setting temperature increased 2Ƈ, the unit will run at this setting temperature; In Heat mode:
sleep status after run for one hour, the setting temperature will decrease 1Ƈ, 2
hours, setting temperature will decrease 2Ƈ, then the unit will run at this setting
temperature.
Sleep 2 is sleep mode 2, that is air conditioner will run according to the presetting
a group of sleep temperature curve.
In Cool mode:
(1) When setting the initial temperature 16Ƈ-23Ƈ, after turned on Sleep function,
the temperature will be increased 1Ƈ in every hour, after 3Ƈ the temperature
will be maintained, after 7hours, the temperature will be decreased 1Ƈ, after
that the unit will keep on running under this temperature;
(2) When setting the initial temperature 24Ƈ-27Ƈ, after turned on Sleep function,
the temperature will be increased 1Ƈ in every hour, after 2Ƈ the temperature
will be maintained, after 7hours, the temperature will be decreased 1Ƈ, after
that the unit will keep on running under this temperature;
(3) When setting the initial temperature 28Ƈ-29Ƈ, after turned on Sleep function,
the temperature will be increased 1Ƈ in every hour, after 1Ƈ the temperature
will be maintained, after 7hours, the temperature will be decreased 1Ƈ, after
that the unit will keep on running under this temperature;
11
Introduction for buttons on remote controller
(4) When setting the initial temperature 30Ƈ, under this temperature setting, after
7hours, the temperature will be decreased 1Ƈ, after that the unit will keep on
running under this temperature;
In Heat mode:
(1) Under the initial presetting temperature 16Ƈ, it will run under this setting temperature all along.
(2) Under the initial presetting temperature17Ƈ-20Ƈ, after Sleep function started
up, the temperature will decrease 1Ƈ in every hour, after 1Ƈ decreased, this
temperature will be maintained.
(3) Under the initial presetting temperature 21Ƈ-27Ƈ, after Sleep function started
up, the temperature will decrease 1Ƈ in every hour, after 2Ƈ decreased, this
temperature will be maintained.
(4) Under the initial presetting temperature 28Ƈ-30Ƈ, after Sleep function started
up, the temperature will decrease 1Ƈ in every hour, after 3Ƈ decreased, this
temperature will be maintained.
Sleep 3 - the sleep curve setting under Sleep mode by DIY:
(1) Under Sleep 3 mode, press "Turbo" button for a long time, remote controller enters into user individuation sleep setting status, at this time, the time of remote
controller will display "1hour", the setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink (The first entering
will display according to the initial curve setting value of original factory);
(2) Adjust "+" and "-" button, could change the corresponding setting temperature,
after adjusted, press "Trubo" button for confirmation;
(3) At this time, 1hour will be automatically increased at the timer postion on the
remote controller, (that are "2hours" or "3hours" or "8hours"), the place of setting temperature "88" will display the corresponding temperature of last setting
sleep curve and blink;
(4) Repeat the above step (2)~(3) operation, until 8hours temperature setting finished,
sleep curve setting finished, at this time, the remote controller will resume the
original timer display; temperature display will resume to original setting temperature.
Sleep3 - the sleep curve setting under Sleep mode by DIY could be inquired:
The user could accord to sleep curve setting method to inquire the presetting sleep
curve, enter into user individuation sleep setting status, but do not change the temperature, press "Turbo" button directly for confirmation.
Note: In the above presetting or enquiry procedure, if continuously within10s, there
is no button pressed, the sleep curve setting status will be automatically quit
and resume to display the original displaying. In the presetting or enquiry procedure, press "ON/OFF" button, "Mode" button, "Timer" button or "Sleep"
button, the sleep curve setting or enquiry status will quit similarly.
12
Introduction for special function
About X-FAN function
This function indicates that moisture on evaporator of indoor unit will be blowed after
the unit is stopped to avoid mould.
1. Having set X-FAN function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 2 min. at low speed. In this period, press
X-FAN button to stop indoor fan directly.
2. Having set X-FAN function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be off directly.
About AUTO RUN
When AUTO RUN mode is selected, the setting temperature will not be displayed on
the LCD, the unit will be in accordance with the room temp. automatically to select the
suitable running method and to make ambient comfortable.
About turbo function
If start this function, the unit will run at super-high fan speed to cool or heat quickly so
that the ambient temp. approachs the preset temp. as soon as possible.
About lock
Press + and - buttons simultaneously to lock or unlock the keyboard. If the remote controller is locked, the icon
will be displayed on it, in which case, press any button,
the mark will flicker for three times. If the keyboard is unlocked, the mark will disappear.
About swing up and down
1. Press swing up and down button continuously more than 2s, the m ain unit will swing
backand forth from up to down , and then loosen the button, the unit will stop swing
and present position of guide louver will be kept immediately.
2. Under swing up and down mode, when the status is switched from off to
, if press
this button again 2s later,
status will switch to off status directly; If press this button
again within 2s, the change of swing status will also depend on the circulation sequence stated above.
About swing left and right
1. Press swing left and right button continuously more than 2s, the main unit will swing
back and forth from left to right, and then loosen the button, the unit will stop swing
and present position of guide louver will be kept immediately.
2. Under swing left and right mode, when the status is switched from off to
, if press
this button again 2s later,
status will switch to off status directly; if press this button
again within 2s, the change of swing status will also depend on the circulation sequence stated above.
13
Introduction for special function
About switch between Fahrenheit and Centigrade
Under status of unit off, press MODE and - buttons simultaneously to switch ć and ̧.
Combination of "TEMP" and "CLOCK" buttons:
About Energy - saving Function
Press “TEMP” and “CLOCK” simultaneously in COOL mode to start energy-saving function. Nixie tube on the remote controller displays “SE”. Repeat the operation to quit
the function.
Combination of "TEMP" and "CLOCK" buttons:
About 8ć Heating Function
3UHVV³7(03´DQG³&/2&.´VLPXOWDQHRXVO\LQ+($7PRGHWRVWDUWć Heating Function
Nixie tube on the remote controller displays “ ” and a seleFWHGWHPSHUDWXUHRI³ć”.
(46̧ if Fahrenheit is adopted). Repeat the operation to quit the function.
Note: If matching with smart zone controller for operation, the display on smart zone
controller will be maintained the original status.
About auto Quiet function
When quiet function is selected:
1. Under cooling mode: indoor fan operates at notch 4 speed. 10 minutes later or when
LQGRRUDPELHQWWHPSHUDWXUH”ćLQGRRUIDQZLOORSHUDWHDWQRWFKVSHHGRUTXLHW
mode according to the comparison between indoor ambinet temperature and set temperature.
8QGHUKHDWLQJPRGHLQGRRUIDQRSHUDWHVDWQRWFKVSHHGRUquiet mode according
to the comparison between indoor ambient temperature and set temperature.
8QGHUGU\IDQPRGHLQGRRUIDQRSHUDWHVDWTXLHWPRGH
4. Under auto mode: the indoor fan operates at the auto quiet mode according to actual
cooling, heating or fan mode.
About Sleep function
Under the Fan and Auto mode, the Sleep function cannot be set up, under Dehumidify
mode, only Sleep 1 can be selected. Select and enter into any kind of Sleep mode, the
Quiet function will be attached and stared, different Quiet status could be optional and
turned off.
14
Operation guide
General operation
4
1. After powered on, press ON/OFF button, the unit will start
to run. (Note: When it is powered on, the guide louver of
main unit will close automatically.)
2. Press MODE button, select desired running mode.
3. Pressing + or - button, to set the desired temperature (It is
unnecessary to set the temp. at AUTO mode.)
4. Pressing FAN button, set fan speed, can select AUTO FAN,
LOW, MEDIUM-LOW, MEDIUM, MEDIUM-HIGH and HIGH.
5. Pressing and button, to select the swing.
3
5
2
1
Optional operation
4
1. Press SLEEP button, to set sleep.
2. Press TIMER ON and TIMER OFF button, can set the
scheduled timer on or timer off.
3. Press LIGHT button, to control the on and off of the
displaying part of the unit (This function may be not
available for some units).
4. Press TURBO button, can realize the ON and OFF of
TURBO function.
2
1
3
Replacement of batteries in remote controller
battery
1. Press the back side of remote controller marked
reinstall
the cover of battery box along the arrow direction.
2. Replace two 7# (AAA 1.5V) dry batteries, and
make sure the position of "+" polar and "-" polar
are correct.
3. Reinstall the cover of battery box.
remove
Cover of battery box
NOTICE
Ɣ'XULQJRSHUDWLRQSRLQWWKHUHPRWHFRntrol signal sender at the receiving
window on indoor unit.
Ɣ7KHGLVWDQFHEHWZHHQVLJQDOVHQGHUand receiving window should be no
more than 8m, and there should be no obstacles between them.
Ɣ6LJQDOPD\EHLQWHUIHUHGHDVLO\LQWKH room where there is fluorescent lamp
or wireless telephone; remote controller should be close to indoor unit during
operation.
Ɣ5HSODFHQHZEDWWHULHVRIWKHVDPHPRGHOZKHQUHSODFHPHQWLVUHTXLUHG
Ɣ:KHQ\RXGRQ¶WXVHUHPRWHFRQWUROOHUIRUDORQJWLPHSOHDVHWDNHRXWWKH
batteries.
Ɣ,IWKHGLVSOD\RQUHPRWHFRQWUROOHULVIX]]\RUWKHUH¶VQRGLVSOD\SOHDVH
replace batteries.
15
Emergency operation
If remote controller is lost or damaged, please use auxiliary button to turn
on or turn off the air conditioner. The operation in details are as below:
air conditioner. When the air conditioner is turned on, it will operate under
auto mode.
panel
aux. button
WARNING:
Use insulated object to press the auto button
Clean and Maintenance
WARNING
Ŷ Turn off the air conditioner and disconnect the power before cleaning the air
conditioner to avoid electric shock.
Ŷ'RQRWZDVKWKHDLUFRQGLWLRQHUZLWKZDWHUWRDYRLGHOHFWULFVKRFN
Ŷ'RQRWXVHYRODWLOHOLTXLGWRFOHDQWKHDLUFRQGLWLRQHr.
Clean surface of indoor unit
When the surface of indoor unit is dirty, it is recommended to use a soft dry cloth
or wet cloth to wipe it.
NOTICE:
Ɣ'RQRWUHPRYHWKHSDQHOZKHQFOHDQLQJLW
16
Clean and Maintenance
1
Open panel
3
Pull out the panel to a certain
Ɣ8VHGXVWFDWFKHURUZDWHUWR
WKHZDWHUEHORZć ) to clean
LWDQGWKHQSXWLWLQDVKDG\
DQGFRROSODFHWRGU\.
2
4
panel cover tightl\.
WARNING
operation environment, clean frequency can be increased.
17
Clean and Maintenance
NOTICE: Checking before use-season
1. Check whether air inlets are blocked.
2. Check whether air switch,plug and socket are in good condition.
&KHFNZKHWKHU¿OWHULVFOHDQ
4. Check whether drainage pipe is damaged.
NOTICE: Checking after use-season
1. Disconnect power supply.
&OHDQ¿OWHUDQGLQGRRUXQLW’s panel.
Notice for recovery
1. Many packing materials are recyclable materials.
Please dispose them in appropriate recycling unit.
2. If you want to dispose the air conditioner, please contact local dealer or
consultant service center for the correct disposal method.
18
Malfunction analysis
General phenomenon analysis
Please check below items before asking for maintenance. If the malfunction still
Phenomenon
Check items
Solution
Ɣ:KHWKHULW
VLQWHUIHUHGVHYHUHO\ Ɣ3XOORXWWKHSOXJ5HLQVHUW
(such as static electricit\, stable the plug after about 3min, and
voltage)?
then turn on the unit again.
Indoor unit
can’t receive
remote
controller’s
signal or
remote
controller
has no
action.
Ɣ:KHWKHUUHPRWHFRQWUROOHULV
within the signal receiving
range?
Ɣ6LJQDOUHFHLYLQJUDQJHLVP
Ɣ:KHWKHUWKHUHDUHREVWDFOHV"
Ɣ5HPRYHREVWDFOHV
ƔSelect proper angle and point
Ɣ:KHWKHUUHPRWHFRQWUROOHULV
pointing at the receiving
WKHUHPRWHFRQWUROOHUDWWKHUH
window?
ceiving window on indoor unit.
Ɣ,VVHQVLWLYLW\RIUHPRWHFRQWUR Ɣ&KHFNWKHEDWWHULHV,IWKH
power of batteries is too low,
OOHUORZIX]]\GLVSOD\DQGQR
please replace them.
GLVSOD\"
Ɣ&KHFNZKHWKHUUHPRWHFRQW
Ɣ1RGLVSOD\ZKHQRSHUDWLQJ
roller appears to be damaged.
remote controller?
,I\HVUHSODFHLW
Ɣ)OXRUHVFHQWODPSLQURRP"
Ɣ Take the remote controller
close to indoor unit.
DQGWKHQWU\LWDJDLQ
1RDLU
emitted
from
indoor
unit
Ɣ Air inlet or air outlet of indoor
unit is blocked?
Ɣ(OLPLQDWHREVWDFOHV
Ɣ8QGHUKHDWLQJPRGHLQGRRU
temperature is reached to set
temperature?
Ɣ $IWHUUHDFKLQJWRVHWWHPSHU
DWXUHLQGRRUXQLWZLOOVWRSEO
owing out air.
Ɣ+HDWLQJPRGHLVWXUQHGRQMXVW Ɣ,QRUGHUWRSUHYHQWEORZLQJ
now?
out cold air, indoor unit will be
VWDUWHGDIWHUGHOD\LQJIRUVHY
HUDOPLQXWHVZKLFKLVDQRU
mal phenomenon.
19
Malfunction analysis
3KHQRPHQRQ
$LUFRQGLW
LRQHUFDQ¶W
RSHUDWH
&KHFNLWHPV
6ROXWLRQ
Ɣ3RZHUIDLOXUH"
Ɣ:DLWXQWLOSRZHUUHFRYHU\
Ɣ,VSOXJORRVH"
Ɣ5HLQVHUWWKHSOXJ
Ɣ$LUVZLWFKWULSVRIIRUIXVHLV
EXUQWRXW"
Ɣ$VNSURIHVVLRQDOWRUHSODFH
DLUVZLWFKRUIXVH
Ɣ:LULQJKDVPDOIXQFWLRQ"
Ɣ$VNSURIHVVLRQDOWRUHSODFHLW
Ɣ8QLWKDVUHVWDUWHGLPPHGLDWHO\
Ɣ:DLWIRUPLQDQGWKHQWXUQ
DIWHUVWRSSLQJRSHUDWLRQ"
RQWKHXQLWDJDLQ
Ɣ:KHWKHUWKHIXQFWLRQVHWWLQJ
IRUUHPRWHFRQWUROOHULV
FRUUHFW"
0LVWLVHP
LWWHGIURP
Ɣ,QGRRUWHPSHUDWXUHDQGKXP
LQGRRUXQLW¶V LGLW\LVKLJK"
DLURXWOHW
6HWWHPSHU
DWXUHFDQ¶W
EHDGMXVWHG
&RROLQJ
KHDWLQJ
HIIHFWLV
QRWJRRG
Ɣ5HVHWWKHIXQFWLRQ
Ɣ%HFDXVHLQGRRUDLULVFRROHG
UDSLGO\$IWHUDZKLOHLQGRRU
WHPSHUDWXUHDQGKXPLGLW\ZLOO
EHGHFUHDVHDQGPLVWZLOO
GLVDSSHDU
Ɣ8QLWLVRSHUDWLQJXQGHUDXWR
PRGH"
ƔTHPSHUDWXUHFDQ¶WEHDGMX
VWHGXQGHUDXWRPRGH
3OHDVHVZLWFKWKHRSHUDWLRQ
PRGHLI\RXQHHGWRDGMXVW
WHPSHUDWXUH
ƔYRXUUHTXLUHGWHPSHUDWXUH
H[FHHGVWKHVHWWHPSHUDWXUH
UDQJH"
Ɣ6HWWHPSHUDWXUHUDQJH
ć ać ƔVROWDJHLVWRRORZ"
Ɣ:DLWXQWLOWKHYROWDJH
UHVXPHVQRUPDO
Ɣ)LOWHULVGLUW\"
Ɣ6HWWHPSHUDWXUHLVLQSURSHU
UDQJH"
ƔAGMXVWWHPSHUDWXUHWRSURSHU
UDQJH
Ɣ'RRUDQGZLQGRZDUHRSHQ"
Ɣ&ORVHGRRUDQGZLQGRZ
20
Malfunction analysis
Phenomenon
Odours are
emitted
Air conditioner operates
abnormally
suddenly
“Water
ÀRZLQJ´
noise
Cracking
noise
Check items
Solution
Ɣ:KHWKHUWKHUH¶VRGRXUVRXUFH Ɣ(OLPLQDWHWKHRGRXUVRXUFH
such as furniture and cigarette,
Ɣ&OHDQWKH¿OWHU
etc.
Ɣ:KHWKHUWKHUH¶VLQWHUIHUHQFH
such as thunder, wireless
devices, etc.
Ɣ'LVFRQQHFWSRZHUSXWEDFN
power, and then turn on the
unit again.
Ɣ$LUFRQGLWLRQHULVWXUQHGRQRU
turned off just now?
Ɣ7KHQRLVHLVWKHVRXQGRI
UHIULJHUDQWÀRZLQJLQVLGH
the unit, which is a normal
phenomenon.
Ɣ$LUFRQGLWLRQHULVWXUQHGRQRU
turned off just now?
21
Ɣ7KLVLVWKHVRXQGRIIULFWLRQ
caused by expansion and/or
contraction of panel or other
parts due to the change of
temperature.
Malfunction analysis
Error Code
Ɣ:KHQDLUFRQGLWLRQHUVWDWXVLVDEQRUPDlWHPSHUDWXUHLQGLFDWRURQLQGRRUXQLWZLOO
DWLRQRIHUURUFRGH
,QGRRU
GLVSOD\
(UURUFRGH
$ERYHLQGLFDWRUGLDJUDPLVRQO\
IRUUHIHUHQFH3OHDVHUHIHUWR
DFWXDOSURGXFWIRUWKHDFWXDO
LQGLFDWRUDQGSRVLWLRQ
(UURUFRGH
TURXEOHVKRRWLQJ
+HDWLQJLQGLFDWRU
21V2))V
0HDQVGHIURVWLQJVWDWXV,W¶VWKHQRUPDOSKHQRPHQRQ
)
3OHDVHFRQWDFWTXDOLILHGSURIHVVLRQDOVIRUVHUYLFH
)
3OHDVHFRQWDFWTXDOLILHGSURIHVVLRQDOVIRUVHUYLFH
&
3OHDVHFRQWDFWTXDOLILHGSURIHVVLRQDOVIRUVHUYLFH
H6
,WFDQEHHOLPLQDWHGDIWHUUHVWDUWLQJWKHXQLW,IQRWSOHDVH
FRQWDFWTXDOLILHGSURIHVVLRQDOVIRUVHUYLFH
1RWH,IWKHUH
UHRWKHUHUURUFRGHVSOHDVHFRQWDFWTXDOLILHGSURIHVVLRQDOVIRU
VHUYLFH
WARNING
Ŷ:KHQEHORZSKHQRPHQRQRFFXUVSOHDVHWXUQRIIDLUFRQGLWLRQHUDQGGLVFRQ
IRUVHUYLFH
Ɣ3RZHUFRUGLVRYHUKHDWLQJRUGDPDJHG
Ɣ7KHUH¶VDEQRUPDOVRXQGGXULQJRSHUDWLRQ
Ɣ$LUVZLWFKWULSVRIIIUHTXHQWO\
Ɣ$LUFRQGLWLRQHUJLYHVRIIEXUQLQJVPHOO
Ɣ,QGRRUXQLWLVOHDNLQJ
Ŷ,IWKHDLUFRQGLWLRQHURSHUDWHVXQGHUDEQRUPDOFRQGLWLRQVLWPD\FDXVH
22
At least 15cm
Space to the ceiling
Installation dimension diagram
Space to the wall
At least 15cm
At least 15cm
Space to the wall
m
At
ce
a
Sp
s
lea
he
ot
At least 250cm
0c
0
t3
n
tio
uc
str
ob
t
23
Tools for installation
1 Level meter
2 Screw driver
3 Impact drill
4 Drill head
5 Pipe expander
6 Torque wrench
7 Open-end wrench
8 Pipe cutter
9 Leakage detector
10 Vacuum pump
11 Pressure meter
12 Universal meter
13 Inner hexagon spanner
Note:
14 Measuring tape
Ɣ3OHDVHFRQWDFWWKHORFDODJHQWIRULQVWDOODWLRQ
Ɣ'RQ
WXVHXQTXDOL¿HGSRZHUFRUG
Selection of installation location
Basic requirement
Installing the unit in the following places maycause malfunction. If it is unavoidable,
please consult the local dealer:
1. The place with strong heat sources, YDSRUVÀDPPDEOHRUH[SORVLYHJDV, or
volatile objects spread in the air.
2. The place with high-frequency devices (such as welding machine, medical
equipment).
3. The place near coast area.
4. The place with oil or fumes in the air.
5. The place with sulfureted gas.
6. Other places with special circumstances.
7. Do not use the unit in the immediate surroundings of a laundry a bath a
shower or a swimming pool.
Indoor unit
1. There should be no obstruction near air inlet .
2. Select a location where the condensation water can be dispersed easily and
ZRQ
WDIIHFWRWKHUSHRSOH
3. Select a location which is convenient to connect the outdoor unit and near the
power socket.
4. Select a location which is out of reach for children.
7KHORFDWLRQVKRXOGEHDEOHWRZLWKVWDQGWKHZHLJKWRILQGRRUXQLWDQGZRQ
W
increase noise and vibration.
7KHDSSOLDQFHPXVWEHLQVWDOOHGPDERYHÀRRU
'RQ
WLQVWDOOWKHLQGRRUXQLWULJKWDERYHWKHHOHFWULFDSSOLDQFH
3OHDVHWU\\RXUEHVWWRNHHSZD\IURPÀXRUHVFHQWODPS
24
Requirements for electric connection
Safety precaution
1. Must follow the electric safety regulations when installing the unit.
$FFRUGLQJWRWKHORFDOVDIHW\UHJXODWLRQVXVHTXDOL¿HGSRZHUVXSSO\FLUFXLWDQG
air switch.
3. Make sure the power supply matches with the requirement of air conditioner.
Unstable power supply or incorrect wiring or malfunction. Please install proper
power supply cables before using the air conditioner.
4. Properly connect the live wire, neutral wire and grounding wire of power socket.
5. Be sure to cut off the power supply before proceeding any work related to
electricity and safety.
'RQRWSXWWKURXJKWKHSRZHUEHIRUH¿QLVKLQJLQVWDOODWLRQ
7. If the supply cord is damaged, it must be replaced by the manufacturer, its
VHUYLFHDJHQWRUVLPLODUO\TXDOL¿HGSHUVRQVLQRUGHUWRDYRLGDKD]DUG
8. The temperature of refrigerant circuit will be high, please keep the interconnection cable away from the copper tube.
9. The appliance shall be installed in accordance with national wiring regulations.
10.Installation must be performed in accordance with the requirement of NEC
DQG&(&E\DXWKRUL]HGSHUVRQQHORQO\
Grounding requirement
7KHDLUFRQGLWLRQHULVWKH¿UVWFODVVHOHFWULFDSSOLDQFH,WPXVWEHSURSHUO\
JURXQGLQJZLWKVSHFLDOL]HGJURXQGLQJGHYLFHE\DSURIHVVLRQDO3OHDVHPDNH
sure it is always grounded effectively, otherwise it may cause electric shock.
7KH\HOORZJUHHQZLUHLQDLUFRQGLWLRQHULVJURXQGLQJZLUHZKLFKFDQ
WEHXVHG
for other purposes.
3. The grounding resistance should comply with national electric safety regulations.
4. The appliance must be positioned so that the plug is accessible.
5. An all-pole disconnection switch having a contact separation of at least 3mm in
DOOSROHVVKRXOGEHFRQQHFWHGLQ¿[HGZLULQJ)RUPRGHOVZLWKDSRZHUSOXJ
make sure the plug is within reach after installation.
25
Installation of indoor unit
Step one: choosing installation location
rm it with the client.
Step two: install wall-mounting frame
1. Hang the wall-mounting frame on the wall; adjust it in horizontal position with the
plastic expansion particles in the holes.
3. Fix the wall-mounting frame on the wall with tapping screws (ST4.2X25TA) and
.
Step three: open piping hole
1. Choose the position of piping hole according to the direction of outlet pipe. The
position of piping hole should be a little lower than the wall-mounted frame,
shown as below.
、 、12K
Wall
Mark in the middle of it
18K
Level meter
Space
to the
wall
above
PP
Wall
Wall
Space
to the
wall
above
PP
Space
to the
wall
above
PP
Left
ĭPP
Rear piping hole
Mark in the middle of it
Right
ĭPP
Rear piping hole
Left
ĭPP
Rear piping hole
Wall
Level meter
Space
to the
wall
above
PP
Right
ĭPP
Rear piping hole
24K
Wall
Mark in the middle of it
Space
to the
wall
above
PP
Left
ĭPP
Rear piping hole
Level meter
Wall
Space
to the
wall
above
PP
Right
ĭPP
Rear piping hole
Note: Please select the corresponding installation dimensional drawing according to actual wall-mounted plate.
2. Open a piping hole with the diameter oIĭRQWKHVHOHFWHGRXWOHWSLSH
position. In order to drain smoothly, slant the piping hole on the wall slightly
GRZQZDUGWRWKHRXWGRRUVLGHZLWKWKHJUDGLHQWRIƒ
26
Installation of indoor unit
Indoor
outdoor
Note:
Ɣ3D\DWWHQWLRQWRGXVWSUHYHQWLRQDQG
WDNHUHOHYDQWVDIHW\PHDVXUHVZKHQ
opening the hole.
Ɣ The plastic expansion particles are
QRWSURYLGHGDQGVKRXOGEHERXJKW
locally.
ĭ
ĭ
5-10
Step four: outlet pipe
2. When select leading out the pipe
from left or right, please cut off the
corresponding hole on the bottom
case.
1. The pipe can be led out in the
direction of right, rear right, left or
rear left.
right
left
right
left
rear right
rear left
cut off
the hole
1. Aim the pipe joint at the corresponding
bellmouth.
pipe joint
union nut
pipe
2. Pretightening the union nut with hand.
3. Adjust the torque force by referring to the following sheet. Place the open-end
wrench on the pipe joint and place the torque wrench on the union nut. Tighten
the union nut with torque wrench.
27
Installation of indoor unit
open-end
wrench
union nut
torque wrench
pipe
Hex nut diameter Tightening torque (N.m)
ĭ
a
ĭ
30~40
ĭ
5a
ĭ
a
ĭ
a
indoor pipe
4. Wrap the indoor pipe and joint of connection pipe with insulating pipe, and
then wrap it with tape.
insulating pipe
,IDNLQGRRUXQLWLVWREHFRQQHFWHGZLWK)UHH0DWFKRXWGRRUXQLWDWUDQVLWLRQDO
SLSHMRLQWSURYLGHGVKRXOGEHDGGHGDWWKHSLSHMRLQWRILQGRRUXQLWHYDSRUDWRUDVV\
DVWKHSLSHMRLQWRIHYDSRUDWRUDVV\DGRSWVSLSHGLDPHWHURIĭ3OHDVHUHIHUWRVWHS
1-4 during installation.
Step six: install drain hose
1. Connect the drain hose to the outlet pipe of
indoor unit.
drain hose
2. Bind the joint with tape.
outlet pipe
drain hose
outlet
pipe
tape
drain hose
Note:
Ɣ Add insulating pipe in the indoor
drain hose in order to prevent
condensation.
Ɣ The plastic expansion particles are
not provided.
insulating pipe
Step seven: connect wire of indoor unit
panel
1. Open the panel, remove the screw
on the wiring cover and then take
down the cover.
28
screw
wiring cover
Installation of indoor unit
2. Make the power connection wire go
through the cable-cross hole at the back
of indoor unit and then pull it out from
the front side.
cable-cross
hole
power connection
wire
3. Remove the wire clip; connect the power connection wire to the wiring terminal
according to the color; tighten the screw and then fix the power connection wire
with wire clip.
N(1)
2
3
blue black brown
yellow-green
outdoor unit connection
4. Put wiring cover back and then tighten the screw.
5. Close the panel.
Note:
Ɣ All wires of indoor unit and outdoor unit should be connected by a professional.
for a new one. Avoid extending the wire by yourself.
installation.
Ɣ)RUWKHDLUFRQGLWLRQHUZLWKRXWSOXJDQair switch must be installed in the line.
The air switch should be all-pole parting and the contact parting distance should
be more than 3mm.
29
Installation of indoor unit
Step eight: bind up pipe
1. Bind up the connection pipe, power
cord and drain hose with the band.
indoor unit
connection pipe
drain hose
band
indoor and
outdoor power cord
gas
pipe
indoor power cord
liquid pipe
3. Bind them evenly.
4. The liquid pipe and gas pipe should
be bound separately at the end.
band
drain hose
2. Reserve a certain length of drain
hose and power cord for installation
when binding them. When binding to
a certain degree, separate the indoor
power and then separate the drain
hose.
Note:
Ɣ The power cord and control wire
can't be crossed or winding.
Ɣ The drain hose should be bound
at the bottom.
Step nine: hang the indoor unit
1. Put the bound pipes in the wall pipe and then make them pass through the wall
hole.
2. Hang the indoor unit on the wall-mounting frame.
3. Stuff the gap between pipes and wall hole with sealing gum.
4. Fix the wall pipe.
5. Check if the indoor unit is installed firmly and closed to the wall.
indoor
wall pipe
upper hook
outdoor
sealing gum
lower hook of
wall-mounting frame
Note:
Ɣ'RQRWEHQGWKHGUDLQKRVHWRRH[FHssively in order to prevent blocking.
30
Check after installation
Items to be checked
Possible malfunction
The unit may drop, shake or emit noise.
Have you done the refrigerant leakage
test?
(heating) capacity.
It may cause condensation and water
dripping.
Is water drained well?
It may cause condensation and water
dripping.
Is the voltage of power supply according to the voltage marked on the
nameplate?
It may cause malfunction or damaging
the parts.
Is electric wiring and pipeline installed
correctly?
It may cause malfunction or damaging
the parts.
Is the unit grounded securely?
It may cause electric leakage.
Does the power cord follow the speci-
It may cause malfunction or damaging
the parts.
Is there any obstruction in the air inlet
and outlet?
(heating) capacity.
The dust and sundries caused during
installation are removed?
It may cause malfunction or damaging
the parts.
The gas valve and liquid valve of
connection pipe are open completely?
(heating) capacity.
Test operation
1. Preparation of test operation
Ɣ The client approves the air conditioner.
Ɣ6SHFLI\WKHLPSRUWDQWQRWHVIRUDLUFRQGLWLRQHUWRWKHFOLHQW
2. Method of test operation
Ɣ3XWWKURXJKWKHSRZHr, press ON/OFF button on the remote controller to start
operation.
Ɣ3UHVV02'(EXWWRQWRVHOHFW AUTO, COOL, DRY, F$1DQG+(AT to check
whether the operation is normal or not.
Ɣ,IWKHDPELHQWWHPSHUDWXUHLVORZHUWKDQć , the air conditioner can’t
start cooling.
31
Configuration of connection pipe
1. Standard length of connection pipe
ƔPPP
0LQOHQJWKRIFRQQHFWLRQSLSHLVP
0D[OHQJWKRIFRQQHFWLRQSLSHDQGPD[KLJKGLfference.
Cooling
FDSDFLW\
Max length
Max height
of connecdifference
tion pipe
Cooling
FDSDFLW\
Max length
Max height
of connecdifference
tion pipe
%WXK
:
%WXK
:
10
%WXK
:
%WXK
:
10
%WXK
:
%WXK
:
20
%WXK
:
20
10
%WXK
:
20
%WXK
:
10
%WXK
:
20
4. The additional refrigerant oil and refrigerant charging required after prolonging
connection pipe
Ɣ $IWHUWKHOHQJWKRIFRQQHFWLRQSLSHLVSURORQJHGIRUPDWWKHEDVLVRI
VWDQGDUGOHQJWK\RXVKRXOGDGGPORIUHIULJHUDQWRLOIRUHDFKDGGLWLRQDOP
of connection pipe.
Ɣ The calculation Pethod of additional refrigerant charging DPount (on the Easis
of liquid pipe):
$GGLWLRQDOUHIULJHUDQWFKDUJLQJDPRXQW = prolonged length of liquid pipe ×
DGGLWLRQDOUHIULJHUDQWFKDUJLQJDPRXQWSHUPHWHU
ƔBasing on the length of standard pipe, add refrigerant according to the
requirement as shown in the table. 7KHDGGLWLRQDOUHIULJHUDQWFKDUJLQJDPRXQW
SHUPHWHULVGLfIHUHQWDFFRUGLQJWRWKHGLDPHWHURIOLTXLGSLSH6HHWKH
following sheet.
32
Configuration of connection pipe
Additional refrigerant charging amount for R22, R407C, R410A and R134a
Diameter of connection pipe
Outdoor unit throttle
Liquid pipe(mm)
Gas pipe(mm)
ĭ
ĭRUĭ
20
ĭRUĭ
ĭRUĭ
ĭ
ĭRUĭ
30
120
ĭ
ĭRUĭ
120
ĭ
_
ĭ
_
Cooling only(g/m) Cooling and heating(g/m)
33
Pipe expanding method
Note:
Improper pipe expanding is the main cause of refrigerant leakage. Please expand
the pipe according to the following steps:
A: Cut the pipe
E: Expand the port
Ɣ([SDQGWKHSRUWZLWKH[SDQGHr.
the distance of indoor unit and
outdoor unit.
Ɣ&XWWKHUHTXLUHGSLSHZLWKSLSHFXWWHr.
hard
mold
expander
pipe
pipe
pipe cutter
leaning
uneven
Note:
Ɣ$LVGLfferent according to the
diameter, please refer to the sheet
below:
burr
B: Remove the burrs
Ɣ5HPRYHWKHEXUUVZLWKVKDSHUDQG
prevent the burrs from getting into
the pipe.
pipe
shaper
downwards
A(mm)
Outer diameter
(mm)
Max
Min
ĭ
ĭ
ĭ
ĭ
F: Inspection
Ɣ&KHFNWKHTXDOLW\RIH[SDQGLQJSRUW
,IWKHUHLVDQ\EOHPLVKH[SDQGWKH
port again according to the steps
above.
C: Put on suitable insulating pipe
D: Put on the union nut
Ɣ5HPRYHWKHXQLRQQXWRQWKHLQGRRU
connection pipe and outdoor valve;
install the union nut on the pipe.
smooth surface
improper expanding
union pipe
leaning
pipe
WKHOHQJWKLVHTXDl
34
damaged
surface
crack
uneven
thickness
Wired Controller (Optional)
If the product you bought is equipped with wired controller, please
refer to the following introductions of wired controller.
1 Displaying Part
Fig1.1.1 Outline of wired controller
1.1 LCD Display of Wired Controller
Fig.1.1.2 LCD display
35
Wired Controller (Optional)
1.2 Instruction to LCD Display
Table 1.1
No.
Symbols
Description
1
Swing function
2
Air exchange function (this function is yet unavailable for this unit).
3
Sleep function (Only sleep 1).
4
Each kind of running mode of indoor unit (auto mode)
5
Cooling mode
6
Dry mode
7
Fan mode
8
Heating mode
9
Defrosting function for the outdoor unit.
10
Gate-control function (this function is yet unavailable for this unit).
11
Lock function.
12
SHIELD
13
Turbo
14
MEMORY
15
16
Turbo function state
Memory function (The indoor unit resumes the original setting state after
power failure and then power recovery).
It blinks under on state of the unit without operation of any button.
SAVE
17
Energy-saving function (this function is yet unavailable for this unit).
Ambient/setting temperature value
18
E-HEATER
19
BLOW
20
21
Shield functions (Button operation, temperature setting, On/Off operation,
Mode setting are disabled by the remote monitoring system.)
Electric auxiliary heating function.
Blow function.
Timing value.
QUIET
Quiet function (two types: quiet and auto quiet)
(this function is yet unavailable for this unit).
36
Wired Controller (Optional)
2 Buttons
2.1 Layout of Buttons
2.2 Functions of Buttons
Table 2.1
No.
Name
1
Enter/Cancel
2
Ÿ
6
ź
3
Fan
4
Mode
5
Function
7
Timer
Timer setting.
8
On/Off
Turn on/off the indoor unit
4+2
Ÿ0RGH
Function
Function selection and cancellation.
ķ .Running temperature setting of the indoor unit, range:16~30oC.
ĸ .Timer setting, range:0.5-24 hr.
Setting of the high/middle/low/auto fan speed.
Setting of the Cooling/Heating/Fan/Dry/Auto mode of the indoor unit.
Switchover among the functions of Turbo/Save/E-heater/Blow etc..
Press them for 5s under off state of the unit to enter/cancel the Memory
function(If memory is set, indoor unit after power failure and then power
recovery will resume the original setting state. If not, the indoor unit is
defaulted to be off after power recovery. Memory off is default before
delivery.).
By pressing them at the same time under off state of the unit,
3+6
)DQź
2+6
Ÿź
will be
will be
displayed on the wired controller for the cooling only unit, while
displayed on the wired controller for the cooling and heating unit.
Upon startup of the unit without malfunction or under off state of the
unit,press them at the same time for 5s to enter the lock state, in which
case,any other buttons won’t respond the press. Repress them for 5s to quit
this state.
37
Wired Controller (Optional)
3 Operation Instructions
3.1 On/Off
Press On/Off to turn on the unit and turn it off by another press.
Note: The state shown in Fig.3.1.1 indicates the “Off” state of the unit after power on. The state
shown in Fig.3.1.2 indicates the “On” state of the unit after power on.
Fig.3.1.1 “Off” State
Fig.3.1.2 “On” State
3.2 Mode Setting
Under ON state of the unit, press the Mode to switch the operation modes as the following
sequence: Auto–Cooling–Dry–Fan–Heating.
3.3 Temperature Setting
Press Ÿor ź to increase/decrease the preset temperature. If pressing either of them
continuously, the temperature will be increased or decreased by 1°C every 0.5s,as shown in
Fig.3.3.1.
In the Cooling, Dry, Fan or Heating mode, the temperature setting range is 16°C~30°C.
In the Auto mode, the setting temperature is unadjustable.
Fig.3.3.1
Fig.3.4.1
38
Wired Controller (Optional)
3.4 Fan Setting
Under the “On” state of the unit, press Fan and then fan speed of the indoor unit will change
circularly as shown in Fig.3.4.1.
Low
Middle
High
3.5 Timer Setting
Under on-state of the unit, Press Timer button to set timer off of the unit. Under off-state of the
unit, press Timer button to set timer on of the unit in the same way.
‡ Timer on setting:
Under off-state of the unit without timer setting, if Timer button is pressed, LCD will display xx.
Hour,with ON blinking. In this case, SUHVVŸ or ź button to adjust timer on and then press Timer to
‡ Timer off setting:
Under on-state of the unit without timer setting, if Timer button is pressed, LCD will display xx.
HourZLWK2))EOLQNLQJ,QWKLVFDVHSUHVVŸRUźEXWWRQWRDGMXVWWLPHURQDQGWKHQSUHVV Timer to
‡&DQFHOWLPHU
After setting of timer, if Timer button is pressed, LCD won’t display xx. Hour so that timer setting
is canceled.
Timer off setting under the “On” state of the unit is shown as Fig.3.5.1.
Fig.3.5.1 Timer off Setting under the “On” State of the Unit
39
Wired Controller (Optional)
Timer on setting under the “Off” state of the unit is shown as Fig.3.5.2.
Fig.3.5.2 Timer on Setting under the “Off” State of the Unit
Timer range: 0.5-24hr. Every press of ŸRU ź will make the set time increased or decreased by
0.5hr. If either of them is pressed continuously, the set time will increase/ decrease by 0.5hr every
0.5s.
40
Wired Controller (Optional)
3.6 Swing Setting
Swing On: Press Function under on state of the unit to activate the swing function. In this case,
Swing Off: When the Swing function is on, press Function to enter the Swing setting
blinking. After that, press Enter/Cancel to cancel this function. Swing setting is
interface,with
shown as Fig.3.6.1.
Fig.3.6.1 Swing Setting
Notes:
ķ . Sleep, Turbo or Blow setting is the same as the Swing setting.
ĸ . After the setting has been done, it has to press the key “Enter/Cancel” to back to the setting
41
Wired Controller (Optional)
3.7 Sleep Setting
Sleep on: Press Function under the On state of the unit till the unit enters the Sleep setting
Sleep off: When the Sleep function is activated, press Function to enter the Sleep setting
status. After that, press Enter/Cancel to cancel this function.
In the Cooling or Dry mode, the temperature will increase by 1°C after the unit runs under
Sleep1 for 1hr and 1°C after another 1hr.After that, the unit will run at this temperature.
In the Heating mode, the temperature will decrease by 1°C after the unit runs under Sleep 1 for
1hr and 1°C after another 1hr. After that, the unit will run at this temperature.
Sleep setting is shown as Fig.3.7.1.
Fig.3.7.1. Sleep Setting
42
Wired Controller (Optional)
3.8 Turbo Setting
Turbo function: The unit at the high fan speed can realize quick cooling or heating so that the
room temperature can quickly approach the setting value.
In the Cooling or Heating mode, press Function till the unit enters the Turbo setting status and
When the Turbo function is activated, press Function to enter the Turbo setting status and then
press Enter/Cancel to cancel this function.
Turbo function setting is as shown in Fig.3.8.1.
Fig.3.8.1 Turbo Setting
43
Wired Controller (Optional)
3.9 E-heater Setting
E-heater (auxiliary electric heating function): In the Heating mode, E-heater is allowed to be
Once the wired controller or the remote controller enters the Heating mode, this function will be
turned on automatically.
Press Function in the Heating mode to enter the E-heater setting interface and then press
Enter/Cancel to cancel this function.
Press Function to enter the E-heater setting status, if the E-heater function is not activated,
and then press Enter/Cancel to activate it.
The setting of this function is shown as Fig.3.9.1 below:
Fig.3.9.1 E-heater Setting
44
Wired Controller (Optional)
3.10 Blow Setting
Blow function: After the unit is turned off, the water in evaporator of indoor unit will be
automatically evaporated to avoid mildew.
In the Cooling or Dry mode, press Function till the unit enters the Blow setting status and then
press Enter/Cancel to active this function.
When the Blow function is activated, press Function to the Blow setting status and then press
Enter/Cancel to cancel this function.
Blow function setting is as shown in Fig.3.10.1
Fig.3.10.1 Blow Setting
Notes:
ķ . When the Blow function is activated, if turning off the unit by pressing On/Off or by the
remote controller, the indoor fan will run at the low fan speed for 2 min, with “BLOW” displayed on
the LCD. While, if the Blow function is deactivated, the indoor fan will be turned off directly.
ĸ . Blow function is unavailable in the Fan or Heating mode.
45
Wired Controller (Optional)
3.11 Other Functions
a. Lock
Upon startup of the unit without malfunction or under the “Off” state of the unit, press Ÿ and źat
the same time for 5s till the wired controller enters the Lock function. In this case, LCD displays
.
After that, repress these two buttons at the same time for 5s to quit this function.
Under the Lock state, any other button press won’t get any response.
b. Memory
Memory switchover: Under the “Off” state of the unit, press Mode and Ÿ at the same time for
5s to switch memory states between memory on and memory off. When this function is activated,
Memory will be displayed. If this function is not set, the unit will be under the “Off” state after power
failure and then power recovery.
Memory recovery: If this function has been set for the wired controller, the wired controller after
power failure will resume its original running state upon power recovery. Memory contents: On/
Off, Mode, set temperature, set fan speed and Lock function.
4 Installation and Dismantlement
4.1 Connection of the Signal Line of the Wired Controller
Ɣ2SHQWKHFRYHURIWKHHOHFWULFFRQWUROER[RIWKHLQGRRUXQLW
Ɣ/HWWKHVLQJOHOLQHRIWKHZLUHGFRQWUROOHUWKURXJKWKHUXEEHUULQJ
Ɣ&RQQHFWWKHVLJQDOOLQHRIWKHZLUHGFRQWUROWRWKHSLQVRFNHWRIWKHLQGRRUXQLW3&%
Ɣ Tighten the signal wire with ties.
Ɣ The communication distance between the main board and the wired controller can be up to
20 meters ( the standard distance is 8 meters)
4.2 Installation of the Wired Controller
39&3LSH
1
2
3
4
5
Fig.4.1 Accessories for the Installation of the Wired Controller
Table 4.1
No.
1
2
3
4
5
Name
6RFNHWER[
embedded
in the wall
Soleplate of
the Wired
Controller
Screw
M4X25
)URQW3DQHO
of the Wired
Controller
Screw
ST 2.9X6
46
Wired Controller (Optional)
1
2
3
7
4
6
8
9
5
10
Fig.4.2
Fig.4.2 shows the installation steps of the wired controller, but there are some issues that need
your attention.
1) Prior to the installation, please firstly cut off the power supply of the wire buried in the
installation hole, that is, no operation is allowed with electricity during the whole installation.
2) Pull out the four-core twisted pair line from the installation holes and then let it go through
the rectangular hole behind the soleplate of the wired controller.
with screws M4X25.
4) Insert the four-core twisted pair line into the slot of the wired controller and then buckle the
front panel and the soleplate of the wired controller together.
CAUTION!
Please pay special attention to the followings during the connection to avoid the malfunction of
the air conditioning unit due to electromagnetic interference.
ķ . Separate the signal and communication lines of the wired controller from the power cord
47
Wired Controller (Optional)
and connection lines between the indoor and outdoor unit, with a minimum interval of 20cm,
otherwise the communication of the unit will probably work abnormally.
ĸ . If the air conditioning unit is installed where is vulnerable to electromagnetic
interference,then the signal and communication lines of the wired controller must be the shielding
twisted pair lines.
4.3 Dismantlement of the Wired Controller
1
2
3
4
5 Errors Display
If there is an error occurring during the operation of the system, the error code will be displayed
on the LCD, as show in Fig.5.1. If multi errors occur at the same time, their codes will be displayed
circularly.
Note: In event of any error, please turn off the unit and contact the professionally skilled
personnel.
Fig.5.1
48
Wired Controller (Optional)
Table 5.1 Meaning of Each Error
Error
Return air temperature sensor open/
short circuited
evaporator temperature sensor open/
short circuited
Indoor unit liquid valve temperature
sensor open/short circuited
Indoor gas valve temperature sensor
open/ short circuited
IPM temperature sensor open/short
circuited
Outdoor ambient temperature sensor
open/ short circuited
Outdoor unit condenser mid-tube
temperature sensor open/short circuited
Discharge temperature sensor open/
short circuited
Error
Code
Error
Error
Code
F1
Drive board communication error
P6
F2
Compressor overheating protection
H3
b5
Indoor and outdoor units unmatched
LP
b7
Communication line misconnected or
expansion valve error
dn
P7
E7
F3
Pump-down
Fo
F4
Jumper error
C5
F5
Forced defrosting
H1
Indoor and outdoor communication error
E6
Compressor startup failure
Lc
DC bus under-voltage protection
PL
High discharge temperature protection
E4
DC bus over-voltage protection
PH
Overload protection
E8
Compressor phase current sensing
circuit error
U1
Whole unit over-current protection
E5
Compressor demagnetization protection
HE
Over phase current protection
P5
PFC protection
Hc
Compressor desynchronizing
H7
IPM Temperature Protection
P8
IPM Current protection
H5
Over-power protection
L9
System charge shortage or blockage
protection
F0
Capacitor charging error
PU
High pressure protection
E1
Low pressure protection
E3
Compressor stalling
LE
Over-speeding
LF
Drive board temperature sensor error
PF
Indoor unit full water error
E9
AC contactor protection
P9
Anti-freezing protection
E2
Temperature drift protection
PE
AC input voltage abnormal
PP
Sensor connection protection
Pd
Whole unit current sensing circuit error
U5
DC bus voltage drop error
U3
4-way valve reversing error
U7
Outdoor fan 1 error protection
L3
Motor stalling
H6
Outdoor fan 2 error protection
LA
PG motor zero-crossing protection
U8
Compressor phase loss/reversal
protection
Frequency restricted/reduced with whole
unit current protection
Frequency restricted/reduced with IPM
current protection
Frequency restricted/reduced with high
discharge temperature
Frequency restricted/reduced with antifreezing protection
Frequency restricted/reduced with
overload protection
Frequency restricted/reduced with IPM
temperature protection
49
Ld
F8
En
F9
FH
F6
EU
2014 Johnson Controls, Inc.
www.johnsoncontrols.com
Doc. No.:UYHJZHAMQ-20141225
Johnson Controls reserve the right to change product features without prior notice.
66129917572
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement