Wi-Fi 6 MESH AP
Quick Start Guide
Azores Networks, LLC
Overview
Thank you for choosing our product.
Please read this manual before use.
If you need to change Internet Access method,i.e.from router to bridge mode,or add a new
Mesh AP to your Mesh network,or need other information,please scan the QR code below or
visit https://azoresnetworks.com/pages/download-center in the browser to view the
corresponding electronic user manual for instructions.
Scan QR code to download electronic user manual
Azores Dual-band Router Model List
AX1500
AX1800
AX1800 PRO
AX3000 PRO
01 Product
Hardware Description
Product Backside Description
AX1500
AX1800
AX1500/AX1800
AX1800 PRO/AX3000 PRO
The picture is for reference only, please refer to the actual product.
Button Description
Button
WPS
Function
Set the WPS process.
Short press (1 second) for reset the router;
Reset
Long press (5 seconds or longer) for reset to factory default settings.
ON/OFF
Power on and off the router.（Model:AX1500/AX1800 PRO/AX3000 PRO）
Turn on or off the LED.Turn off the LED indicator for a better sleep.
LED ON/OFF
The LED indicator switch will not affect the operation of Azores Router.
（Model:AX1800）
LED Description
LED Behavior
Dark
02 Product
Scenario
No Power
Steady Red
Powering up
Blinking Red
No network cable connected
Blinking Green
Network connection in progress
Steady Green
Function normally and can access the Internet
Blinking Blue
WPS or Mesh pairing in progress
Steady Blue
Pairing successful
Manual
Single Router
AX1500/AX1800
AX1800 PRO/AX3000 PRO
For single router：
Connect the provided network cable from the Azores Router to your home Broadband Gateway (i.e. cable/DSL
modem, PON gateway). Please refer to SINGLE ROUTER SETUP STEPS for network setup.
Mesh Router Set
AX1500/AX1800
AX1800 PRO/AX3000 PRO
For mesh router set:
Main AP has the QR code on the label, is used as the main router, which is to be connected, via provided network
cable, to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway); Satellite AP is used for Wi-Fi
network expansion. Please refer to ONE ROUTER SETUP STEPS (for Main AP) & MESH SETUP STEPS (for
Satellite AP) for network setup.
When Single Router and Main AP in Mesh Router Set have the same operation steps, they are collectively
referred to as Azores Router hereinafter.
03 ONE
ROUTER SETUP STEPS
The Azores Router can be connected according to the diagram above. Note the DSL/PON/Cable Gateway
must be connected to the WAN Port of Azores Router. When it is connected to the Internet ,the LED light is
steady green. If you can, try place the Azores Router in an open area like on a table or a shelf.
Wired devices can be connected directly to LAN Port(s) for Internet access; Wireless devices can use the
network name (SSID) & password (see the sticker on the bottom(or backside) of Azores Router) to connect
to Internet.
04 MESH
SETUP STEPS
Place the Satellite AP at a proper location based on your home layout. After powering on again, Satellite AP is all
set when the LED is steady green. To optimize wireless performance, place the Satellite AP in a location that
minimizes the barrier (such as wall, door, and floor) between the Main AP and Satellite AP. We recommend one
wall/door/floor between the Main AP and Satellite AP. You can connect the Satellite AP to your Main AP via
network cable (preferred method) or wirelessly.
Note:
(1) If you know there is a spot in your home, where the Wi-Fi signal is the weakest. Try place the Satellite AP midway
between the Main AP and the weakest spot.
(2) When Main AP and Satellite AP pairing successfully, the SSID and Password would be same, that is showing on the
bottom of Main AP.
05 Azores
Router APP
01 Connect your Mobile device to Wi-Fi network according to the Wi-Fi SSID and password sticker on the label
of Azores Router.
02 Download mobile APP software by scanning the QR code below or visiting
https://azoresnetworks.com/pages/app-download in the browser.
Scan QR code to download Azores Router APP
03 Follow the APP guidance to log in.
04 Enter the “My Wi-Fi” menu to modify WiFi configuration or perform other operations.
*Note: If you want to use the mobile device to perform other operations on the router, follow the instructions on the
mobile APP.
06 Frequently
Asked Questions
Q1 I replaced my old router with Azores
(2) If PPPoE Internet access is needed, you need
Router.After connecting network cable
to check whether the broadband account and
from DSL/PON/Cable gateway to the
password are filled in correctly;Otherwise, check
Azores Router, the LED is keep flashing
whether the Internet status of your Broadband
red.What should I do?
Gateway is normal.
Answer:For some cable carriers limit the number of
(3) Make sure the broadband service is normal and
in-home device to one. This problem may happen if
you have paid Internet bill.
you replace your old router with Azores Router.In
(4) When all above are normal, try reboot the
this case, you need to power down the cable
device and then check the network once it powers
gateway,leave it powered down for 15 seconds and
back on.
power back it up. Afterwards, power down and on
the Azores Router,then you should see the LED
turns steady green pretty soon.
Q2 How to reset the device?
Answer: WhenAzores Router is powered on,
pushing the “Reset” hole on the bottom of the
device with a needle. The LED starts to flash green
Q4 How to manage Azores Router
network?
Answer: Connect your device to the Router using
wireless or wired connection. Open an Internet
browser
and
enter
http://192.168.0.1(or
http://azoresrouter.com). You can modify WAN
configuration, router configuration, single SSID for
2.4G and 5G network, guest Wi-Fi network, and
retrieve your wireless network status.
and hold for 5 more seconds. Release when the
LED turns off. The LED will become steady red and
Q5 Azores Router APP cannot control
will then start to blink green. Wait for about 2
Azores Router.What should I do?
minutes, then the factory default reset is completed.
Answer: Please check your phone is connected to
WiFi normally, and use the correct password for
Q3 Mobile phones and other devices are
login.
connected to the router but cannot
access the Internet.
Q6 If the way that you connect to the
Answer: (1) Check whether the Azores Router's
network is different from shown in the
WAN Port is connected to your Broadband
figure in “ONE ROUTER SETUP
Gateway. The Azores Router's network port should
STEPS”,or the IP address conflicts with
be connected to your Broadband gateway (i.e.
the address of the deployed home
DSL/Cable modem, PON gateway) with a network
router/gateway,how to configure Internet
cable.
access?
、Answer:Try put Router in bridge mode.Please scan
the QR code(on page 1) to view the electronic user
manual to switch to bridge mode.
Q7 What if I already purchased a Mesh
Router set and want to further expand the
network with additional AP(s)?
Answer:You need to purchase another or more
Azores routers(the same model) and expand the
current mesh network.Please scan the QR code to
view the electronic user manual to obtain the
customized mesh network operation method.
Q8 How to access the Satellite AP web
management page(GUI) if the mesh
pairing failed?
Answer:Manually set the PC IP address to
192.168.0.X(e.g.192.168.0.100),the subnet mask is
255.255.255.0.Open the browser and enter
http://192.168.0.254.
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different.
from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and
operated with minimum distance of 20cm the radiator your body. This device and its antenna(s) must
not be co-located or operation in conjunction with any other antenna or transmitter
ISED Canada Statement:
This device contains licence-exempt trasnsmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada 's licence-exempt RSS(s). Operation is subject to the
following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Radiation Exposure: This equipment complies with Canada radiation
exposure limits set forth for an uncontrolled environment
RF Exposure Statement
To maintain compliance with IC's RF Exposure guidelincs, This
cquipment should be.installed and operated with minimum distance of
20cm the radiator your body. This device and its antenna(s) must not be
co-located or operation in conjunction with any other antenna or
transmitter
Déclaration de l'ISED Canada :
Cet appareil contient des émetteurs / récepteurs exempts de licence se
conformer à l'innovation, la science et le développement économique
Les RSS du Canada exemptes de licence. Leur fonctionnement suivant
deux conditions:
1) cet appareil ne peut pas causer d'interférences et
2) ce dispositif doit accepter toute interférence, y compris
peut provoquer le fonctionnement indésirable de l'appareil.
Exposition aux rayonnements : Cet équipement est conforme aux radiations du Canada
limites d'exposition pour un environnement incontrôlé
noncé d'exposition RF
Pour maintenir le respect des guides d'exposition RF d'IC,
cquipment doit être.installé et actionné avec une distance minimale de
20cm le radiateur de votre corps. Cet appareil et ses antennes ne doivent pas être
co-localisé ou en opération en conjonction avec toute autre antenne ou
émetteur
">
