- Computers & electronics
- TVs & monitors
- Video splitters
- Interlogix
- 4-Port Fast Ethernet/PoE-af Mid-span Injector
- User manual
Interlogix 4-Port Fast Ethernet/PoE-af Mid-span Injector User Manual
Add to my manuals14 Pages
Interlogix 4-Port Fast Ethernet/PoE-af Mid-span Injector is a compact and reliable solution for powering and networking your IP devices over a single Ethernet cable. It provides a cost-effective and easy way to extend the reach of your PoE network, and it's perfect for use in a variety of applications, such as powering IP cameras, VoIP phones, and wireless access points.
advertisement
IFS POE201-MS/4
4-Port PoE-af Injector
User Manual
P/N 1072580 • REV R00.04 • ISS 31JAN13
Copyright
Trademarks and patents
© 2013 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of
United Technologies Corporation. All rights reserved.
The IFS POE201-MS/4 4-Port PoE-af Injector and logo are trademarks of United Technologies.
Intended use
Manufacturer
Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
Use this product only for the purpose it was designed for; refer to the data sheet and user documentation for details. For the latest product information, contact your local supplier or visit us online at www.interlogix.com.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue
Costa Mesa, CA 92626-5923, USA
EU authorized manufacturing representative:
UTC Fire & Security B.V., Kelvinstraat 7,
6003 DH Weert, The Netherlands
Certification
FCC compliance
ACMA compliance
Canada
N4131
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Notice!
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
This Class A digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe A est conforme á la norme
NMB-003du Canada.
European Union 2004/108/EC directives
Americas Corporation, Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC. symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Contact information
For contact information see our Web site: www.interlogix.com.
Contact support
www.interlogix.com/customer
Contents
Appendix A: Network Connection 7
Contacting Technical Support 10
IFS POE201-MS/4 4-Port PoE-af Injector User Manual i
Package Contents
Thank you for purchasing the IFS POE201-MS/4, an IEEE
802.3af High Power over Ethernet Injector Hub.
Open the package containing the Ethernet Injector Hub and carefully unpack it. The box should contain the following items:
● User Manual x1
If any of these items are missing or damaged, please contact your distributor or IFS Sales Rep. If possible, retain the original carton and packaging material and use them again to repack the product in case there is a need to return it to us for repair.
Product Features
The IFS POE201-MS/4 is a 4-Port IEEE 802.3af Power over
Ethernet injector hub complies with IEEE 802.3, IEEE 802.3u and IEEE 802.3af standards. Equipped with 4 10/100Base-TX
Fast Ethernet ports, the POE201-MS/4 supports full 48V DC power for any remote IEEE 802.3af powered device (PD) like
Wireless LAN Access Point, IP Phone, and IP Camera.
Providing up to 70 watts, the, POE201-MS/4 provides sufficient power for up to 4 remote devices.
There are 8 RJ-45 ports on the POE201-MS/4. The ports on the right panel function as "Data" and the other half on the left panel function as "Data and Power". Each of the "Data and
Power"
port has an injector which inserts DC Voltage into the
CAT 5 cable allowing the cable between the Injector and
Splitter to transfer data and power simultaneously.
• Complies with IEEE 802.3, IEEE 802.3u, 10/100Base-TX
• Complies with IEEE 802.3af, 48V DC power over unused twisted-pair wires
• 4-Port IEEE 802.3af in-line mid-span power injector box
IFS POE201-MS/4 4-Port PoE-af Injector User Manual 1
• Full power support (15.4W) on each POE port
• Circuit protection prevents power interference between ports
• LED indicators power input indication
• Small Compact Design
2 IFS POE201-MS/4 4-Port PoE-af Injector User Manual
Product Overview
Figure 1 shows the front and side panels of the POE201-MS/4.
Figure 1: POE201-MS/4 Front and Side Panels
IFS POE201-MS/4 4-Port PoE-af Injector User Manual 3
LED Indicators
POE201-MS/4 LED indicators
LED Color Function
PWR
PoE In-use
Green
Lit indicates that the POE201-MS/4 has power.
Green
Lit indicates that the PoE port is providing 56VDC in-line power.
Hardware Installation
This product provides two different running speeds – 10Mbps and 100Mbps- in the same device and automatically distinguishes the speed of the incoming connection.
This section describes the hardware features of the POE201-
MS/4. Before connecting any network device to the POE201-
MS/4, read this chapter carefully.
Before Installation
The POE201-MS/4 requires an AC-DC adapter with DC 48V input and injects this DC power into the pins of the twisted pair cable (pair 4, 5 and pair 7, 8).
If there is no convenient location to plug the AC-DC Adapter of your non-IEEE 802.3af networked device, the POE201-MS/4 and SP-POE can provide a way to supply DC power for this
Ethernet device conveniently and easily.
The 10Mbps or 100Mbps speed, duplex mode from Data port of the POE201-MS/4 depends on which Ethernet device is attached.
Injector Installation
For installation locations where it's hard to find a power outlet, the POE201-MS/4 provides an easier way to power your
4 IFS POE201-MS/4 4-Port PoE-af Injector User Manual
Ethernet devices such as an IFS IEEE 802.3af Power over
Ethernet Splitter (SP-POE) for non-PoE devices.
The POE201-MS/4 can be directly deployed to connect the third party IEEE 802.3af devices installed 100 meters away.
Figure 2: Connection Architecture
Note:
According to the IEEE 802.3af standard, the POE201-
MS/4 will not inject power to the cable if it is not connected to
IEEE 802.3af devices.
IFS POE201-MS/4 4-Port PoE-af Injector User Manual 5
Troubleshooting
This chapter contains information to help you solve problems.
If the POE201-MS/4 is not functioning properly, make sure the
POE201-MS/4 is set up according to instructions in this manual.
How can my non IEEE 802.3af network devices can work with the POE201-MS/4?
Solution: You can use IFS Power over Ethernet Splitter, such as the IFS SP-POE to work as a power transformer between the POE201-MS/4 and non-IEEE 802.3af devices.
The PoE LED is not lit
Solution: Check the cable connection between the POE201-
MS/4 and IEEE 802.3af device.
Why is the PoE device not powered although it's connected to the POE201-MS/4?
Solution: Please check the cable type of the connection from
POE201-MS/4 to the other end. The cable should be an 8-wire
UTP, Category 5/5e, EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100 meters, all will affect the power supply.
Please check and assure the device that fully complied with
IEEE 802.3af standard.
6 IFS POE201-MS/4 4-Port PoE-af Injector User Manual
Appendix A: Network Connection
RJ-45 Pin Assignments
10/100Mbps, 10/100Base-TX
Contact
1
2
3
4, 5
6
7, 8
RJ-45 Connector pin assignment
MDI
Media Dependant
MDI-X
Media Dependant
Interface
Tx + (transmit)
Interface -Cross
Rx + (receive)
Tx - (transmit)
Rx + (receive)
Rx - (receive)
Tx + (transmit)
IEEE 802.3af DC 48V
Rx - (receive) Tx - (transmit)
IEEE 802.3af DC 0V
The standard RJ-45 receptacle/connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of a straight cable and crossover cable connection:
Figure A-1: Straight-Through and Crossover Cable
IFS POE201-MS/4 4-Port PoE-af Injector User Manual 7
Please make sure that the cables used are with same pin assignment and color as above picture before deploying the cables into your network.
Energy Saving Note of the Device
This power required device does not support standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing the power cable, the device will still consume power from the power source. For energy savings and reducing the unnecessary power consumption, we strongly suggest that you remove the power connection for the device if this device is not intended to be active.
8 IFS POE201-MS/4 4-Port PoE-af Injector User Manual
Specifications
Model
Ethernet Connector
Ethernet Data Rate
Input Voltage
Number of Device can be Powered
Ethernet Cable
LED Indicator
POE201-MS/4
8-Port RJ-45 STP with 4-Port "Data" and 4-Port "Data
and Power"
10/100Mbps( vary on Ethernet device attached)
DC 48V, 1.5A
4
TIA/EIA-568, Category 5/5e cable
1 x power, 4 x POE ready / in-use
Operating Environment 0~50 Degree C, 5%~90%RH
Storage Environment -10~70 Degree C, 5%~90%RH
Dimension (H x W x D) 26 x 70 x 97mm
Weight 220g
Emission FCC Class B, CE mark
Standard Compliance IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3af Power over Ethernet
IFS POE201-MS/4 4-Port PoE-af Injector User Manual 9
Contacting Technical Support
Contact technical support if you encounter any difficulties during this installation. Please contact us by phone or go to www.interlogix.com/customer-support .
Technical Support
Europe, Middle East and Africa
W Select Contact Us at www.utcfssecurityproducts.eu
North America
T +1 855.286.8889
Australia
10 IFS POE201-MS/4 4-Port PoE-af Injector User Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Complies with IEEE 802.3af PoE standard
- Provides up to 15.4W of power per port
- Supports 10/100Mbps data rates
- Plug-and-play installation
- Compact and lightweight design
- Cost-effective and energy-efficient
Related manuals
Frequently Answers and Questions
How many devices can I power with the Interlogix 4-Port Fast Ethernet/PoE-af Mid-span Injector?
What is the maximum power output of the Interlogix 4-Port Fast Ethernet/PoE-af Mid-span Injector?
What type of Ethernet cables can I use with the Interlogix 4-Port Fast Ethernet/PoE-af Mid-span Injector?
advertisement
Table of contents
- 3 Contents
- 5 Package Contents
- 5 Product Features
- 7 Product Overview
- 8 LED Indicators
- 8 Hardware Installation
- 8 Before Installation
- 8 Injector Installation
- 10 Troubleshooting
- 11 Appendix A: Network Connection
- 11 RJ-45 Pin Assignments
- 11 10/100Mbps, 10/100Base-TX
- 11 The standard RJ-45 receptacle/connector
- 12 Energy Saving Note of the Device
- 13 Specifications
- 14 Contacting Technical Support