RGN 8016L Operating Manual
PDF
Download
Document
Advertisement
Advertisement
Operating Manual --Stapler 8016L – long nose-- NOTE: Please read and fully understand the instructions in this manual before operating the pneumatic power tool. Carefully read through this OPERATOR'S MANUAL to ensure efficient, safe operation. It is recommended that the Manual be kept readily available as an important reference when using this tool. 1 IMPORTANT INFORMATION WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. When using the tool, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read and understand tool labels and operating instructions, safety precautions and warnings in this manual before operating or maintaining this nailer. Failure to follow warnings could result in DEATH or SERIOUS INJURY. Most accidents that result from the operation and maintenance of nailers are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs and by observing appropriate safety procedures. Basic safety precautions are outlined in the "SAFETY" section of this manual and in the sections which contain the operation and maintenance instructions. Hazards that must be avoided to prevent bodily injury or tool damage are identified as DANGERS or WARNINGS on the nailer and in this manual. Never allow the nailer to be operated by children or individuals who have not reviewed this manual. OPERATE THE NAILER ACCORDING TO THIS MANUAL. WARNING! Always follow the tool manufacturer's safety and maintenance instructions. Always wear safety glasses with side shields when operating or servicing tools. Always disconnect the air supply from the tool and empty the magazine when servicing tools. SAVE THIS MANUAL FOR FUTURE REFERENCE! 2 WARNING: The operating instructions shall draw attention to the following a) Only those fasteners listed in the operating instructions may be used in the fastener driving tools; NOTE: The fastener driving tool and the fasteners listed in the operating instructions must be seen as one unit system in terms of technical safety. b) Only the main energy and the lubricants listed in the operating instructions may be used; c) Fastener driving tools marked with an inverted equilateral triangle standing on one point may only be used with an effective safety yoke; d) Fastener driving tools equipped with contact actuation or continuous contact actuation, marked with the symbol “Do not use on scaffoldings, ladders”, shall not be used for specific application for example: when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or ladder alike constructions, e.g. roof laths, closing boxes or crates, fitting transportation safety systems e.g. on vehicles and wagons; e) For the maintenance of fastener driving tools, only spare parts specified by the manufacturer or his authorized representative shall be used; f) Repairs shall be carried out only by agents authorized by the manufacturer or by other specialists, having due regard to the information given in the operating instructions; NOTE: Specialists are those who, as a result of professional training or experience, have sufficient expertise in the field of fastener driving tools and sufficient familiarity with relevant governmental industrial protection provisions, accident prevention regulations, directives and generally recognized technical regulations (e.g. CEN- and CENELEC-standards), to be able to assess the safe working condition of fastener driving tools. g) Stands for mounting the fastener driving tools to a support for example a work table, shall be designed and constructed by the stand manufacturer, in such a way that the fastener driving tool can be safely fixed for the intended use, thus for example avoiding damage, distortion or displacement. Additional instructions for fastener driving tools operated by compressed air a) Fastener driving tools operated by compressed air shall only be connected to compressed air lines where the maximum allowable pressure cannot be exceeded by a factor of more than 10%, which can for example be achieved by a pressure reduction valve which includes a downstream safety valve; b) When using fastener driving tools operated by compressed air, particular attention must be paid to avoid exceeding the maximum allowable pressure; c) Fastener driving tools operated by compressed air should only be operated at the lowest pressure required for the work process at hand, in order to prevent unnecessarily high noise levels, increased wear and resulting failures; d) Hazards caused by fire and explosion when using oxygen or combustible gases for operating compressed air operated fastener driving tools. 3 SAFETY INFORMATION WARNING: BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING SAFETY INSTRUCTIONS.FAILURE TO FOLLOW WARNING COULD RESULT IN DEATH OR SERIOUS INJURY. 1. WEAR SAFETY GLASSES OR GOGGLES. Danger to the eyes always exists due to the possibility of dust being blown up by the exhausted air or of a fastener flying up due to the improper handling of the tool. For these reasons, safety glasses or goggles shall always be worn when operating the tool. The employer and/or user must ensure that proper eye protection is worn. The employer is responsible to enforce the use of eye protection equipment by the tool operator and all other personnel in the work area. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. 2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVIRONMENTS. As the working condition may include exposure to high noise levels which can lead to hearing damage, the employer and user should ensure that any necessary hearing protection is provided and used by the operator and others in the work area. 3. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR. The tool is designed to operate on compressed air. Do not operate the tool on any other high pressure gas, combustible gases (e.g. Oxygen, acetylene, etc.) since there is the danger of an explosion. For this reason, absolutely so not use anything other than an air compressor to operate the tool. 4. OPERATE WITHIN THE PROPER AIR PRESSURE RANGE. The tool is designed to operate within an air pressure range of 70 psi to100 psi (5 to 7 bar). The pressure should be adjusted to the type of the work being fastened. The tool shall never be operated when the operating pressure exceeds 120 psi. (8.3 bar). 5. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE. Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Volatile fumes from these substances could be drawn into the compressor and compressed together with the air and this could result in an explosion. 4 6. DO NOT USE A WRONG FITTING. The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the line of air is disconnected, possibly causing injury. 7. DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS NOT IN USE. Always disconnect the air supply from the tool and empty the magazine when operation has been completed or suspended, when unattended, moving to a different work area, adjusting, disassembling, or repairing the tool, and when clearing a jammed fastener. 8. INSPECT SCREW TIGHTNESS. Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put into operation. Inspect to confirm that all screws and bolts are tight and properly installed prior to operating the tool. 9. DO NOT TOUCH THE TRIGGER UNLESS YOUR INTEND TO DRIVER A FASTENER. Whenever the air supply is connected to the tool, never touch the trigger unless you intend to drive a fastener into the work. It is dangerous to walk around carrying the tool with the trigger pulled, and this and similar actions should be avoided. 10. NEVER POINT THE DISCHARGE OUTLET TOWARD YOURSELF AND PERSONNEL. If the discharge outlet is pointed toward people, serious accidents may be caused when misfiring. Be sure the discharge outlet is not pointed toward people when connecting and disconnecting the hose. Loading and not loading the fasteners or similar operations. 11. USE SPECIFIED FASTENERS. The use of fasteners other than specified fasteners will cause the tool malfunction. Be sure to use only specified fasteners when operating the tool. 12. PLACE THE DISCHARGE OUTLET TO THE WORK PROPERLY. Failure to place the discharge outlet of the nose in a proper manner can result in a fastener flying up and is extremely dangerous. 13. KEEP HANDS AND BODY AWAY FROM THE DISCHARGE OUTLET When loading and using the tool, never place a hand or any part of body in fastener discharge area of the tool. It is very dangerous to hit the hands or body by mistake. 5 14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK AND THIN MATERIAL The work piece is likely to split and the fastener could fly and hit someone. 15. DO NOT DRIVE FASTENERS ON THE TOP OF OTHER FASTENERS. Driving fasteners of the top of other fasteners may cause deflection fasteners which could cause injury. 16. REMOVING THE FASTENERS AFTER COMPLETING OPERATION If fasteners are left in the magazine after the completion of operation, there is the danger of a serious accident occurring prior to the resumption of operation, should the tool be handled carelessly, or when connecting the air removes all fitting. For this reason, always move the fasteners away which remaining in the magazine after completion of the operation. 17. CHECK OPERATION OF THE CONTACT TRIP MECHANISM FREQUENTLY IN CASE OF USING A CONTACT TRIP TYPE TOOL Do not use the tool if the trip is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact trip mechanism. 18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE. When fastening roofs or similar slanted surface, start fastening at the lower part and gradually work your way up. Fastening backward is dangerous as you may lose your foot place. Secure the hose at a point close to the area you are going to driver fasteners. Accidents may be caused due to the hose being pulled inadvertently or getting caught. 19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER, CONTACT ARM) IS INOPERABLE DISCONNECTED, ALTERED OR NOT WORKING PROPERLY. 20. NEVER ACTUATE THE TOOL INTO FREE SPACE. This will avoid any hazard caused by free flying fasteners and excessive strain of the tool. 21. ALWAYS ASSUME THAT THE TOOL CONTAINS FASTENERS. 22. DO NOT USE ON SCAFFOLDINGS LADDERS. The tool shall not be used for specific application for example: When changing one driving location to another involves the use of scaffoldings, stairs, ladders, or Ladder alike constructions, e.g. roof laths, Closing boxes or crates, Fitting transportation safety systems e.g. on vehicles and wagons. 6 TECHNICAL DATA Type of tool Stapler 8016L – long nose Dimensions 190 mm X 45 mm X 220 mm Weight (without fasteners) 1.1 kg Actuation mode Single-sequential actuation Magazine capacity 157 Staples Maximum allowable pressure 8 bar (120 psi) Recommended pressure range 4 bar to 7 bar (60 psi to 100 psi) Fasteners Only the staple sizes shown in the table below can be driven with this nailer. 21 Ga. Staples Applications Furniture; Picture frames; Decoration; 7 MAINTENANCE AND INSPECTION Read the section title SAFETY. SERVICE AND REPAIRES All quality tools will eventually require servicing or replacement of parts due to wear from normal use. It is recommended that these operations should be performed by a professional technician. NOTE: The information contained in this Manual is designed to assist you in the safe maintenance of the nailer. Some illustrations in this Manual may show details or attachments that are different from those on your nailer. WARNING: Disconnect air hose and remove nails from nailer when: Doing maintenance and inspection Cleaning a jam Inspecting the magazine 1. DISCONNECT AIR HOSE. 2. Clean the magazine. Remove dust which may have accumulated in the magazine. 3. Lubricate the nailer rail with nailer lubricant. Clearing a jam Remove a jammed nail in the following order: 1. DISCONNECT AIR HOSE. 2. Remove all nails. 3. Remove the jammed nail with a slotted head screwdriver. 4. In case of frequent jams, contact an authorized service center. A qualified person should perform repair and maintenance Periodic maintenance to be performed: Check that the piston bumper is operating normally. A damaged piston bumper may cause damages to other component parts. Check o-rings for wear or damage. Damaged o-rings may affect overall performance. Make sure all screws are secure. Loose screws may affect overall performance. When repairing a tool, make sure the internal parts are clean and lubricated. Storing When not in use of an extended period, apply a thin coat of the lubricant to the steel parts to avoid rust. The nailer should be stored in a warm and dry place when not in use. Do not store the nailer in a cold weather environment. 8 GENERAL WARRANTY CONDITIONS Warranty will be honored, only if: 1. Clean, dry, regulated compressed air has been used at air pressure not exceeding the maximum indicated on the tool casting; 2. No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modifications or storage of the product exists; 3. No deviations from following recommended operating instructions, specifications, and maintenance schedules exist.(Read Operating Manual for use, specifications and maintenance instructions). 9 PARTS LIST – 8016L NO. Description NO. 1 CODE 511120 O-RING 2.5X1.8 27 CODE 322700 Description LOCK PAWL 2 511100 O-RING 12.2X1.75 28 421510 COVER 3 511060 O-RING 15.5X1.75 29 322660 BACK COVER 4 511110 O-RING 16.4X1.8 30 410620 BUMPER 5 511080 O-RING 16X1.25 31 110490 BODY 6 511090 O-RING 8X2.6 32 322720 SILENCER 7 511140 O-RING 25X2.65 33 410660 DAMPER 8 511050 O-RING 27.5X2.6 34 421450 VALVE GASKET 9 511040 O-RING 31.5X2.65 35 421460 VALVE CAP 10 510390 O-RING 17X2.65 36 421470 TRIGGER 11 322830 PIN 37 310450 VALVE CYLINDER 12 640290 STRAIGHT PIN 3X24 38 421440 VALVE SHAFT 13 640310 STRAIGHT PIN 4X19.5 39 410640 INTERMEDIATE VALVE 14 630300 WASHER 40 322910 CYLINDER CAP 15 610490 BOLT M4X12 41 310540 CYLINDER 16 610500 BOLT M4X16 42 322920 BACK NOSE ASSEMBLY 17 610720 BOLT M4X14 43 310550 COVER 18 310470 END CAP 44 210880 FRONT COVER 19 621030 TENSION SPRING 45 322930 DRIVER BLADE 20 511130 O-RING 19.5X3 46 322750 PULLEY 21 322690 FEED BAR 47 322670 PIN 22 421430 PISTON 48 421490 STOP 23 421480 VALVE PIN 49 640170 ROLL PIN 3X28 24 421500 END PIECE 50 410630 RUBBER HANDLE 25 421520 COVER 51 640320 STRAIGHT PIN B4X29 26 621040 LEG SPRING P1. D322931 DRIVER UNIT 10 TOOL SCHEMATIC – 8016L 11 IMPORTER: NOBE ApS Bjødstrupvej 10 DK – 8410 Rønde Denmark Tel: + 45 8615 1913 E-Mail: [email protected] www.nobe.dk / www.rgneurope.com --Stapler 8016L – long nose-2016 12 ">

Public link updated
The public link to your chat has been updated.
Advertisement