Roboto Manual - Starlight Entertainment

Roboto Manual - Starlight Entertainment
Technical Specifications
Power
AC 120V~60Hz or AC 230/240/250V 50/60Hz
Fuse
20mm Glass T6.3A Fast Blow
Lamp
HTI 150W
Dimension 373mm x 295mm x 451 mm
Weight
13 kg
IH9000-1
User Guide
Innovation , Quality , Performance
Professional Entertainment Technology
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in which
the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
TABLE OF CONTENTS
Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
1. Safety Instruction
Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60
days.
2. Technical Specification
2.1 Inserting/Exchanging rotating gobos
EC Declaration of Conformity
2.2 Beam angel
We declare that our products (lighting equipments) comply with the following
3. Lamp
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
4. How To Set The Unit
4.1 Control Panel
4.2 Main Function
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
2-
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
&
Harmonized Standard
5.3 iSolution Operation / Universal DMX Controller
5.4 DMX512 Configuration
EN 60598-1: 2004
5.5 DMX512 Connection
IEC 60598-1:2003+ corrigendum 2004
Part 1:General requirements and test
6. Troubleshooting
Following the provisions of the low voltage directive 73/23/EEC and 93/68/EEC
7. Fixture Cleaning
1. Safety Instruction
H. If The pan belt is broken
1. Turn off the main power.
2. Unscrew all the screws (A) and open the base-housing cover (B).
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
3. Unplug all the connect wires (C) that from the arm to PC board and igniter.
4. Unscrew the screws (D) that fix the bridge (E).
WARNING
5. Unscrew the screws (F) that fix the axis gear (G).
♦
6. Change a new belt (H) by going through all connecting wires that from the arm to base,
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
and through the bridge for correct position.
7. Set up the gear axis to the bridge and screwed it. Note: do not press the belt.
♦
Unpack and check carefully there is no transportation damage before using the unit.
♦
Before operating, ensure that the voltage and frequency of power supply match the
8. Put the belt around the axis gear and motor gear.
power requirements of the unit.
9. Plug all the connect wires (C) that form the arm to PC board and igniter.
♦
The unit is designed for use with the HTI 150W. Do not use any other type of lamp.
10. Adjust the pan home position.
♦
It’s important to ground the yellow/green conductor to earth in order to avoid electric
11.Screw the base-housing cover (B).
shock.
♦
The unit is for indoor use only. Use only in a dry location.
♦
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
3-
♦
Disconnect main power before fuse/lamp replacement or servicing.
♦
Replace fuse/lamp only with the same type.
♦
Make sure there are no flammable materials close to the unit while operating, as it
is fire hazard.
♦
G
D
H
A D
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only,
but always by taking its base.
♦
E
C
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature
is higher than this.
B
♦
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
during its operation. Turn off the power and allow about 15 minutes for the unit to
F
cool down before replacing bulb or serving.
♦
In the event of serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
B
A
A
center. Always use the same type spare parts.
♦
Don’t connect the device to any dimmer pack or power pack.
♦
Do not touch any wire during operation as high voltage might be causing electric
shock.
.
6. Troubleshooting
Warning
Following are a few common problems that may occur during operation. Here are
♦ To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
some suggestions for easy troubleshooting:
moisture.
♦ Never touch bulb with bare fingers as it is very hot after using.
A. The unit does not work, no light and the fan does not work
♦ Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
1. Check the connection of power and main fuse.
♦ Do not start on the unit without bulb enclosure or housing are damaged.
2. Measure the mains voltage on the main connector.
♦ The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
3. Check the power on LED.
damaged.
B. Not responding to DMX controller
♦ Do not look directly at the light while the bulb is on.
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
Caution
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
There are no user serviceable parts inside the unit. Do not open the housing or attempt
of the unit or the previous one.
any repairs yourself. In the unlikely event your unit may require service, please contact
4. Try to use another DMX controller.
your nearest dealer.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 30
kgs for each unit.
4-
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
5.5 DMX512 Connection
2. Technical Specification
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1
2
3
Power supply
- AC 120V~60Hz
4
Lamp
- Discharge HTI 150W GY 9.5
Optical system
- Standard 13° focused beam angle.
Shutter/Dimmer
- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per second).
DMX512 INPUT
120 ohm 1/4W
Gobo wheel
COMMON
1
DMX INPUT
3
2
DMX +
1
DMX -
2
3
- Independent gobo wheel with 7 gobos plus open, gobos are interchangeable: 4 metal
DMX OUTPUT
Termination reduces signal errors and to avoid signal
transmission problems and interference. It is always
advisable to connect a DMX terminal.
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
pin3 (DMX+) of the last fixture.
gobos, 2 glass gobos, and 1 effect gobo.
- Gobo wheel rotates with variable speed, giving shaking effect.
1
Color wheel
3
2
- Independent color wheel with 9 dichroic mirrors plus white.
- Color wheel rotates with variable speed, giving rainbow effect.
1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm 1/4W
Movement
5-
- Pan: 540° in 2.8 second.
resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the
- Tilt: 270° in 1.6 second.
DMX-output of the last unit.
DMX Channels
3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to the
- Standard DMX512 signal addressing and can be controlled by any universal DMX controller.
input of the next unit. The cable can not branched or split to a “Y” cable. DMX512 is a very
high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors
can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when
power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the controller.
The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
Channel
Channel
Channel
Channel
Channel
Channel
Channel
Channel
1
2
3
4
5
6
7
8
Pan motion
Tilt motion
Shutter/ Shaking
Gobo
Color
Gobo Rotation
Dimmer
Dimension: 373mm x 295mm x 451mm
Weight: 13 kg
2.1 Inserting/Exchanging rotating gobos
5.4 DMX512 Configuration
DANGER!
Install the gobos with the device switched off only.
Unplug from mains before changing gobos!
Open the cover by loosening the fastening screw at the sides of the cover.
If you wish to use other forms and patterns as the standard-gobos, or if the gobos are to be
exchanged, remove the fixation ring with an appropriate tool. Remove the gobo and insert the
new gobo. Press the fixation-ring together and insert it in the front of the gobo.
6-
CAUTION!
Never unscrew the screws of the rotating gobo as the ball bearing
will otherwise be opened!
2.2 Beam angel
3. Lamp
Stand by Blackout the unit
Strobe
1.Gobo/Color sync.
strobe
Function 2.Sync. strobe
3.Two-light strobe
Mode
Sound 1
(LED off )
X/Y moving show
mode selection
( Show 1 ~ Show 4 )
Please refer to Show
mode in 4.2 Main
Function.
Sound 2
(LED normal blinking)
Color/Gobo selection
1. Hold on for gobo
change.
2. Press shortly for
color change.
Slow/Sound 3
(LED on)
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master unit,
then set Slave units’
position.
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
Because of its high internal pressure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is harmful to
Position/ Latch
(LED fast blinking)
the eyes and skin. The high luminance of the arc can cause severe damage to the retina
if looks directly at the lamp.
5.3.1 iSolution Operation
Discharge lamp : HTI 150W
♦
Consistent DMX configuration enable iMove to be linked together with iRock and iShow
1. Always switch off the main supply and never handle the lamp or luminaries when is
and controlled at the same time.
♦
hot.
DMX address can be set remotely by iLead controller ( please refer to the user manual
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
of iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦
alcohol and wipe it with a lint free cloth before installation.
Automatic switching between DMX function and built-in stand alone programs.
3. The lamp generates UV radiation. Never operate the lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube
5.3.2 DMX Controller
7-
rupture. The risk increases with age, temperature and improper handling of the lamp. Do
not use the lamp any longer than its specified life.
An universal DMX controller to control the units, you have to set DMX address from 1 to 512
channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when the
display stops blinking or storing automatically 8 seconds later. To go back to the functions
without any change press the MENU button again. Please refer to the following diagram to
address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
channels of each fixture in the chain.
5. Make sure the lamp is located in the center of the reflector for the best spot. Adjust
lamp position by screws A, B and C.
4. How To Set The Unit
5. How To Control The Unit
You can operate the unit in three ways:
4.1 Control Panel
1. By master/slave built-in preprogram function
2. By easy controller
3. By iLead controller ( please refer to the user guide of iLead ) or by universal DMX
controller
No need to turn the unit off when you change the DMX address, as new DMX address setting
will be effected at once. Every time you turn the unit on, it will show IM8S / IM7S on the
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in
programs.
5.1 Master/Slave Built-In Preprogrammed Function
Display
To show the various menus and the selected functions .
You can select blackout mode
in
(yes blackout) or
(no blackout)
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
LED
will control the other units to give an automatic, sound activated, synchronized light show.
DMX
MASTER
SLAVE
SOUND
On
On
On
Flashing
DMX input present
Master Mode
Slave Mode
Sound activation
Button
MENU
DOWN
UP
ENTER
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
8-
This function is good when you want an instant show. You have to select
(show 1) or
(show 2) or
(show 3) or
(show 4) mode by easy controller. Its
DMX input jack will have nothing plugged into it, and Its master LED will be constantly on and
sound LED will flash to the music. The other units will have to set in slave mode
and
select
(normal) or
(2 light show) mode, Their DMX cables plugged into the
DMX input jacks (daisy chain) and the slave LED lights will constantly on.
2-light show
Remote controller input
In
By connect to the 1/4” microphone jack to control the unit for Stand by, Function and Mode
show. In order to create a great light show, you can set
on the second unit to get
contrast movement to each other, even if you have two units only.
Sensitivity
(slave mode),
means the unit works normally and
To adjust the sound sensitivity .
Microphone
5.2 Easy Controller
To receive audio signal for sound activation .
The easy remote controller is used only in master/slave mode. By
DMX input/output
connecting to the 1/4” microphone jack of the first unit, you will find that
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
the remote control on the first unit will control all the other units for
Stand by, Function and Mode.
means 2-light
4.2 Main Function
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
when the
To select any of the pre-set functions, press the MENU button up to when the required one is
shown on the display. Select the function by ENTER button and the display will blink. Use
is blinking on the display. Use the ENTER button to change to the mode
DOWN and UP button to change the mode. Once the required mode has been selected,
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
button again return to the mode
the MENU button.
press the ENTER button to setup or it will automatically return to the main functions without
(display normal). To go back to the functions press
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are shown below:
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
DMX512 Address Setting
Focus Adjust
Show mode 1
Show mode 2
Show mode 3
Show mode 4
Slave Mode " Normal "
Slave mode " 2 Light Show "
Blackout Mode " Yes Blackout "
Blackout Mode " No Blackout "
Normal Color
Split Color
Pan Normal
Pan Inversion
Tilt Normal
Tilt Inversion
Dimmer Normal
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan 180°,
pan 270° in every pressing ENTER button. Use DOWN and UP button to adjust focus. To go
back to the functions press the MENU button again.
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the unit will run self-test by built-in program. To go back to the functions press the
9-
MENU
MENU button again.
Dimmer Inversion
LED on
LED off
Display Normal
Display Inversion
Fixture Hours
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
Focus Adjust
Self-Test
Reset
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
functions press the MENU button again.
Fixture Hours
Reset
DMX512 Address Setting
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the DMX512
address. Once the address has been selected, press the ENTER button to setup or
automatically return to the main functions without any change after 8 seconds. To go back to
the functions without any change press the MENU button again.
Show Mode
Press the MENU button up to when the
Color Mode
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
Press the MENU button up to when the
(show 1) or
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(show 2) or
(show 3) or
(show 4) mode. Once the mode has been
selected, press the ENTER button to setup or automatically return to the main functions
(split color) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
without any change after 8 seconds. To go back to the functions without any change press
back to the functions without any change press the MENU button again.
the MENU button again.
Pan Inversion
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Press the MENU button up to when the
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
button and the display will blink. Use DOWN and UP button to select the
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting to
the audience’s direction; i.e in front of the stage. Pan movement angel ( left to
is showing on the display. Pressing ENTER
(normal) or
(pan inversion) mode. Once the mode has been selected, press the ENTER button
to setup or automatically return to the main functions without any change after 8 seconds. To
right to left ): 160°. Tilt movement angel: 90° ( 60° above horizon; 30° below
go back to the functions without any change press the MENU button again.
horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in front
of the stage. Pan movement angel ( left to right to left ) :160°. Tilt movement
angel: 90° ( vertically, front 75°; back 15° )
Press the MENU button up to when the
10-
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(tilt inversion) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
Slave Mode
Press the MENU button up to when the
Tilt Inversion
back to the functions without any change press the MENU button again.
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(2 light show) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Dimmer Inversion
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(normal) or
(dimmer inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
Blackout Mode
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the
(yes
seconds. To go back to the functions without any change press the MENU button again.
Led Display
blackout) or
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change after
Press the MENU button up to when the
8 seconds. To go back to the functions without any change press the MENU button again.
button and the display will blink. Use DOWN and UP button to select the
is showing on the display. Pressing ENTER
(Led on) or
(Led off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To go
back to the functions without any change press the MENU button again.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement