®
BRILLIANT WONDERS
®
1.5" LED LIGHT
INSTALLATION INSTRUCTIONS & PRODUCT MANUAL
25503-500-000
25503-520-000 (P-Style and H-Style)
25503-560-000 (P-Style and H-Style)
Cord Lengths Available:
25’, 50’, 100’, 150’
LED WATERFALL | LED BUBBLER | LED LIGHTS | LED LAMINAR CMP DOCUMENT 11120-000-000_Rev.A
CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM
2. IMPORTANT WARNINGS & SAFETY
INSTRUCTIONS
DANGER
WARNING
Serious bodily injury or death can result if these lights are not installed and used correctly.
Installers, pool operators, and pool owners must read these warning and all instructions before using these lights.
WARNING
WARNING
Before installing this product, read and follow all warning notices and instructions in this guide. Failure to follow warnings and instructions can result in severe bodily injury, death, or property damage.
These underwater swimming pool lights must be installed by a licensed or certified electrician or a qualified pool professional in accordance with the National Electric Code (NEC) or Canadian
Electric Code (CEC), CSA C22.1.
CAUTION
WARNING
NOTICE
NOTICE
All applicable local installation codes and ordinances must also be adhered to. Improper installation will create an electrical hazard which could result in death or serious injury to pool users, installers, or others due to electric shock. Always disconnect power to the pool lights before servicing.
Turn off power to light before installation/service. CMP Brilliant
Wonders 1.5" LED Light is a low voltage light and should never be electrically connected to a power source other than an approved pool
“Safety Rated,” UL listed, outdoor rated, 12 VAC transformer. Failure to comply will either damage or destroy the light and will void the warranty.
No separate ground or bonding wire is required for the Brilliant
Wonders 1.5” LED Lights which have no exposed metal. They do not require a niche.
Save these instructions. This installation and user guide contains important information about the installation, operation, and safe use of this swimming pool/spa light. This guide should be given to the owner and/or operator of this equipment.
2
3. INSTALLATION INSTRUCTIONS
STEP 1
The light must be installed in or on a wall of the pool (or water feature) with the top of the lens opening no less than 4 inches (10.16 cm) below normal water level of the pool.
For vertical installations on benches, swim outs and fountains the depth of the light underwater must still be no less than 4 inches.
NOTE: Requires the use of a 1.5" threaded wall fitting.
NOTE: 12" minimum of 1.5" pipe to accommodate the LED Light. Then 1" pipe to control box with sweeps only, no 90° bends.
1” PIPE
NO 90°
BENDS
STEP 2
Install supplied 2-conductor electric cord through the conduit outlet of the wall into the conduit and up to the location of the 12VAC pool/spa transformer. Cut off excess cord installing appropriate service length.
NOTICE
Allow 18"-24" extra slack in the cord on the 12VAC pool transformer end for future service of the LED light.
1.5” PIPE
(12” MINIMUM) 1.5” WALL FITTING
12VAC
ONLY
4” MIN. FROM WATER
LEVEL TO TOP OF LENS
Allow 18”-24” slack for
Service Loop
3
3. INSTALLATION INSTRUCTIONS
(CONTINUED)
An example of an approved pool transformer is the Intermatic model PX-100 or PX-300.
Refer to Wire Gauge and Wire Length guide for proper wire gauge size in reference to the use of Junction Box installations.
NOTE : Brilliant Wonders 1.5” LED Light can be used with any UL Listed, outdoor rated,
12VAC transformer provided the wattage and amperage is not exceeded by the total wattage and amperage in use.
Control/
Timer/
Automation
Transformer
Primary
110V - 120V
Secondary
12 VAC
L
N
110V - 120V
WIRING CONNECTION TO TRANSFORMER
A Red wire is used with the Brilliant Wonders Controller. If another timer or switch is installed, there may not be a red wire. If this is the case, follow this wiring structure:
Black = Hot
White = Neutral
Green = Ground
4
3. INSTALLATION INSTRUCTIONS
(CONTINUED)
STEP 3
Thread the Faceplate into the 1.5" Threaded
Wall Fitting using the included Installation
Tool until snug (do not over tighten). Tighten set screw using a 2mm Allen wrench (not included).
STEP 4
Connect male and female electrical cord connections and thread together until snug.
Install light into Faceplate by snapping included Installation Tool into the 4 rectangle holes in the LED Lens and then gently pushing in the LED Light while twisting the Installation
Tool clockwise until it clicks into place. Pull
Installation Tool straight out to disconnect it from the LED lens.
WINTERIZATION CLAUSE
Pool water level must be drained 12" below light(s) position in pool wall. It is recommend that the lights be loosened from their Wall Fittings to allow drainage of water that might have accumulated inside the conduit. It is recommended to disconnect cord connections and remove the 1.5" LED Light completely for the winter. Consult your local swimming pool professional for proper local area winterization processes.
LIGHT IS SERVICEABLE
Do not disassemble any part of the Brilliant Wonders 1.5” LED Light body. Only remove cord at connection between male and female connectors.
5
4. OPERATION INSTRUCTIONS
NOTICE
When syncing multiple LED light products, color shows will match but cycle timings may vary.
CMP/J-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The CMP/J-STYLE Brilliant Wonders 1.5" LED Light is preprogrammed with the following color sequence:
SEQUENCE ORDER
1
2
3
6
7
4
5
10
11
12
8
9
13
14
COLOR MODE
Alpine White
Sky Blue
Cobalt Blue
Caribbean Blue
Spring Green
Emerald Green
Emerald Rose
Magenta
Violet
Slow Color Splash
Fast Color Splash
America the Beautiful
Fat Tuesday
Disco Tech
To operate the light and change colors:
• Turn the light ON. The first time the light is turned on, the color sequence will begin with Alpine
White. To change color, turn light OFF then back ON within three (3) seconds. Continue turning OFF and ON until the desired light color mode is reached.
• When the light is turned off for more than seven (7) seconds, it will remain in the color mode that was currently active when the light was turned off.
• To RESET the light to the beginning color sequence (Alpine White), turn the light OFF, wait four (4) to six (6) seconds, then turn the light ON.
6
4. OPERATION INSTRUCTIONS
[CONTINUED]
H-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The H-STYLE Brilliant Wonders 1.5” LED Light is preprogrammed with seventeen light modes:
SEQUENCE ORDER
1
2
3
6
7
4
5
12
13
14
15
8
9
10
11
16
17
COLOR MODE
Voodoo Lounge
Deep Blue Sea
Royal Blue
Afternoon Skies
Aqua Green
Emerald
Cloud White
Warm Red
Flamingo
Vivid Violet
Sangria
Twilight
Tranquility
Gemstone
USA!
Mardi Gras
Cool Cabaret
To operate the light and change colors:
• The H-STYLE Brilliant Wonders 1.5” LED Light is operated through power-cycling; a method of changing modes which requires no special controller or interface. To activate the light simply turn the power switch ON. To advance to the next programmed light mode, turn the switch OFF then back
ON within ten (10) seconds. Whenever the light has been off for more than sixty (60) seconds, and it is first turned on, it will come on white for 15 seconds, then go back to the last programmed light mode it was running before being powered off.
To sync the light with additional H-STYLE lights:
• The H-STYLE Brilliant Wonders 1.5” LED Light can easily be synced with additional H-STYLE lights. All lights should be wired to the same switch, this should automatically sync the lights. If the lights get out of sync on the same switch: turn the switch OFF, then wait between eleven (11) and fourteen (14) seconds and turn the switch back ON. When the lights come back on, they should enter program mode number one (1) and be synchronized.
7
4. OPERATION INSTRUCTIONS
[CONTINUED]
P-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The P-STYLE Brilliant Wonders 1.5” LED Lights can be controlled using a standard wall-mount light switch. Multiple lights can be connected via a junction box to a single switch so that all lights can be switched ON and OFF together. P-STYLE Lights are controlled by cycling the AC power from a standard wall switch. By turning the switch ON and OFF a specific number of times, the light activates one of the seven (7) light show modes, fixed colors, and enables the “Hold” and “Recall” feature.
The P-STYLE Brilliant Wonders 1.5” LED Light is preprogrammed with seven light show modes (1-7) and five fixed color modes (8-12). For saving color effects during the “show” modes the light also includes and “Hold” and “Recall” feature (13-14).
SEQUENCE ORDER
1
2
3
6
7
8
4
5
9
10
11
12
13
14
COLOR MODE
SAm® Mode
Party Mode
Romance Mode
Caribbean Mode
American Mode
California Sunset Mode
Royal Mode
Blue
Green
Red
White
Magenta
Hold
Recall
Example to operate the light and change to “California Sunset” show mode:
• Turn the light switch ON and OFF six (6) times.
• During the ON/OFF switching process, no illumination will occur, then a white light will momentarily illuminate.
• The white light will immediately be followed by the selected “California Sunset” mode.
Hold and Recall Features Example:
• Use the “Hold” feature to capture a unique color effect while “Romance Mode” is active.
• Turn switch on and off thirteen (13) times.
• Saved color effect is displayed.
• From any light show or fixed color mode...
• Turn switch ON and OFF fourteen (14) times to activate last saved color effect.
• Saved color effect is displayed.
8
5. AVAILABLE ACCESSORIES
25500-104-007
(Included)
Brilliant Wonders 1.5" LED Light
Installation Tool
25500-510-200
Brilliant Wonders 1.5" LED Light
Stainless Steel Faceplate
25503-510-000
25503-511-000
25503-514-000
25503-517-000
25503-559-000
25503-569-000
25503-519-000
White (Included)
Gray
Black
Dark Gray
Light Blue
Dark Blue
Tan
Brilliant Wonders 1.5" LED Light
Plastic Faceplate
25503-510-220
25503-511-220
25503-514-220
25503-517-220
25503-559-220
25503-569-220
25503-519-220
SS-White
SS-Gray
SS-Black
SS-Dark Gray
SS-Light Blue
SS-Dark Blue
SS-Tan
Brilliant Wonders 1.5” LED Light
Color Accent Faceplate
For the most recent instructions, videos and product information visit www.c-m-p.com
9
FOR PRODUCT IMAGES, VIDEOS, LITERATURE
AND UP-TO-DATE INSTRUCTIONS VISIT
WWW.C-M-P.COM
ON YOUR COMPUTER OR MOBILE DEVICE
10
CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM
