CMP Brilliant Wonders® 4″ LED Bubbler Instruction manual
CMP 25503-460-000 Brilliant Wonders 4 Inch Led Bubbler offers a mesmerizing water display with its adjustable plume height and two orifice size options for customized water flow. Ideal for vinyl, fiberglass, or gunite pools, it features a durable construction with a 4-inch diameter and a floating collar for easy installation. The bubbler operates on a safe 12VAC power supply and includes a 12VAC transformer for hassle-free setup.
Advertisement
Advertisement
®
BRILLIANT WONDERS
®
4" LED BUBBLER
INSTALLATION INSTRUCTIONS & PRODUCT MANUAL
25503-460-XXX
25503-460-XXXP
25503-460-XXXH
Cord Lengths Available:
25’, 50’, 100’, 150’
LED WATERFALL | LED BUBBLER | LED LIGHTS | LED LAMINAR
90602-550-301 REV E
CUSTOM MOLDED PRODUCTS | 36 HERRING ROAD, NEWNAN, GA 30265 | WWW.C-M-P.COM
IMPORTANT WARNINGS & SAFETY
INSTRUCTIONS
DANGER
WARNING
WARNING
WARNING
CAUTION
WARNING
NOTICE
NOTICE
Serious bodily injury or death can result if these lights are not installed and used correctly.
Installers, pool operators and pool owners must read these warnings and all instructions before using these lights.
Before installing this product, read and follow all warning notices and instructions in this guide. Failure to follow warnings and instructions can result in severe bodily injury, death, or property damage.
These underwater swimming pool lights must be installed by a licensed or certified electrician or a qualified pool professional in accordance with the National Electric Code (NEC) or Canadian Electric
Code (CEC), CSA C22.1.
All applicable local installation codes and ordinances must also be adhered to. Improper installation will create an electrical hazard which could result in death or serious injury to pool users, installers, or others due to electric shock. Always disconnect power to the pool lights before servicing.
Turn off power to light before installation/service. CMP Brilliant
Wonders ® 4" LED Bubbler light module is a low voltage light and should never be electrically connected to a power source other than an approved pool "Safety Rated," UL listed, outdoor rated, 12 VAC transformer. Failure to comply will either damage or destroy the light and will void the warranty.
No separate ground or bonding wire is required for the CMP Brilliant
Wonders® 4” LED Bubbler light module which have no exposed metal. They do not require a niche.
Save these instructions. This installation and user guide contains important information about the installation, operation, and safe use of this swimming pool/spa light. This guide should be given to the owner and/or operator of this equipment.
2
PART & TOOLS LIST
INCLUDED PARTS - 4" BUBBLER BOX
Main Body Assembly Pressure Test Hardware
6X M4 Machine Screws
6X M4 Hex Nuts
Floating Collar
(Gunite Only)
Large Lens, L-Gasket, Eyeball,
Orifice Discs, Lubricant
INCLUDED PARTS - LED LIGHT BOX
Stopper Assembly Pressure Test Cap And
Pressure O-Ring
REQUIRED TOOLS
1. 7 mm Wrench
2. 3/8" Socket Wrench
3. 3/8" Socket Extender
4. PVC Glue
5. Level
6. Phillips Head Screw
Driver
7. O-Ring Lubricant
Led Light Module Installation Tool Electric Cable
3
INSTALLATION STEPS
VINYL/FIBERGLASS POOL
INSTALLATION STEPS
1. Use a 3.5" hole saw and cut a hole in the desired location of the 4" Bubbler.
2. Use template included with your Vinyl
Faceplate Kit to drill six holes around the 3.5" hole using an 11/64" or #17 drill bit.
3. Install one gasket under the vinyl, or fiberglass, and one on the water side.
4. Secure the Vinyl Trim Ring with the 6 x M4 Stainless Steel Screws included with your Vinyl Liner Kit.
NOTICE
Fiberglass installation may require longer
M4 Stainless Steel Screws (not included).
GUNITE INSTALLATION STEPS
1. Install gunite up to flange of the Main
Body.
2. Use Pressure Test Cap (25503-460-
208) as a debris guard while installing gunite.
3. Determine finishing height of the plaster.
4. The finishing height of the plaster should line up just below the top of the Floating Collar.
5. The Floating Collar is designed to allow up to 0.5" of adjustability before gluing, to better match the final plaster height.
6. Glue Floating Collar into main body using PVC glue.
7. Wait for glue to dry then install the plaster to just below the top of the
Floating Collar.
4
VINYL TRIM RING
GASKET (2)
NOTE: FIBERGLASS
MAY REQUIRE
LONGER M4
MACHINE SCREWS
VINYL LINER KIT PART LIST
1. Decorative Ring
2. 2x Gaskets
3. M4 Stainless
Steel Screws (6)
4. Cutting Template
GASKET/PLASTER
FINISH HEIGHT
USE PROTECTIVE CAP
AS DEBRIS GUARD
GASKET/PLASTER
FINISH HEIGHT
GUNITE
FINISH HEIGHT
NOTICE
VINYL, OR
FIBERGLASS
BETWEEN TWO
GASKETS
FLOATING COLLAR
MAX HEIGHT
0.5” ADJUSTABLE
Make certain that all screws and hex nuts are hand tight before pressure testing the unit
WATER
PLUMBING & ELECTRICAL DIAGRAMS
GENERAL PLUMBING GUIDE
12 VAC
TRANSFORMER/
JUNCTION BOX
FLOW CONTROL
BUBBLER
1.5” CONDUIT
SWEEP
REQUIRED
FROM PUMP
PUMP
1 1/2” PVC PIPE
• Water inlet is 1.5" PVC socket.
• Power inlet is 1.5" conduit socket.
• A minimum of one (1.5" x 90°) sweep conduit required. After this, 1" conduit can be used to the junction box.
• Water depth must be between 2"-12".
• Beach entry slope must not exceed 1/12 grade to keep plume perpendicular with water surface.
• Pressure test all pipe fittings according to your local building codes.
• Your 4" Bubbler is shipped ready to pressure test.
1” CONDUIT
GENERAL ELECTRICAL DIAGRAM
CONTROL BOX
ABOVE WATER LEVEL
12V AC ONLY
12VAC
18” - 24” EXTRA
SLACK FOR A
SERVICE LOOP
1” CONDUIT
1.5“ x 90°
SWEEP
REQUIRED
• Connect CMP 4" Bubbler LED Light
Module to a 12V AC transformer. Listed, outdoor rated 12VAC transformer must be used. Check that the transformer’s wattage and amperage are not exceeded by the total wattage and amperage in use (load).
• CMP 4" Bubbler LED Light Module
(25503-460-900) final operating depth must be at least 2" underwater.
• A minimum of one (1.5" x 90°) sweep or
12" of straight conduit must be installed into the electical socket on the bottom of the 4" Bubbler.
• Use sweeps only in electrical conduit line. No 90° bends.
5
STEP-BY-STEP INSTALLATION GUIDE
1. Post and level the 4" bubbler unit.
for vinyl/fiberglass see pg 7
2. Install plumbing using PVC glue.
Make sure screws are tight then pressure test the unit.
3. Install conduit. 1.5" × 90° sweep required. Can use 1" conduit to the junction box.
for vinyl/fiberglass see pg 7
0.5” - 1.1” PLASTER
THICKNESS
4. Remove screws and nuts. Leave cap for debris guard. Install concrete/ gunite to top of unit.
for vinyl/fiberglass see pg 7
5. Remove Pressure Test Cap, pressure o-ring and the stopper assembly.
6. Determine plaster height. Use PVC glue and install collar with plaster height slightly below top of collar.
12V AC ONLY
12VAC
APPLY O-RING
LUBRICANT 18” - 24” EXTRA
SLACK FOR A
SERVICE LOOP
7. Replace Pressure Test Cap as a debris guard. Install plaster up to
6 slightly below the top of the collar.
8. Install electric cable to a 12VAC transformer. Leave 18"- 24" service loop at the control box.
9. Apply lubricant to bottom of LED module. Install LED module with
Installation Tool. Rotate clockwise until it clicks.
STEP-BY-STEP INSTALLATION GUIDE
CONTINUED
APPLY O-RING
LUBRICANT
1
2
1
3
2
10. Install L-gasket making sure it is seated properly in the groove.
Apply lubricant to top of L-gasket.
Install large lens using the
Installation Tool. Rotate clockwise until you feel a “click” and the lens stops rotating.
11. Install orifice disc into the eyeball.
Install eyeball into large lens by rotating 90° and inserting. Rotate eyeball to desired position.
VINYL/FIBERGLASS ONLY
INSTALLATION STEPS
All installation steps are the same for vinyl/fiberglass installation as they are for gunite installation, except the adjustable collar comes pre-glued from our factory for the vinyl/fiberglass units.
VINYL TRIM RING
VINYL, OR
FIBERGLASS
BETWEEN TWO
GASKETS
REMOVE AFTER
PRESSURE TEST
3.5” HOLE SAW
USE PAPER
TEMPLATE AND
11/64 DRILL BIT
GASKET (2)
NOTE: FIBERGLASS
MAY REQUIRE
LONGER M4
MACHINE SCREWS
1. Cut hole in desired location using
3.5" hole saw. Use paper template to drill 6 holes using 11/64 drill bit.
2. Secure bubbler to vinyl/fiberglass shell using Trim Kit.
3. To pressure test, install Pressure
Test Cap and O-Ring into bubbler.
Rotate clockwise until it stops rotating. Pressure test the unit.
Remove cap, and stopper.
7
OPERATING PROCEDURES
WATER PATH OPERATING PROCEDURES
25°
TWO ORIFICE SIZE
OPTIONS
3/8” and 1/2”
• The adjustable Eyeball can be angled up to 25° from vertical.
• The Orifice Disk snaps into the
Eyeball.
• Two orifice size options are included with your 4" Bubbler: 3/8" and 1/2".
• A smaller orifice opening will have higher water pressure and plume height.
• A larger orifice opening will have lower water pressure and plume height.
• Flow control valve can be adjusted to meet desired performance.
NOTICE
The Stopper Assembly can be used for installing Orifice Discs. (see pg 3) PERFORMANCE CHART
1. Factors such as water flow rate, orifice size and water depth above the orifice will all contribute to the final look of the plume height. The performance chart below can be used as a reference in deciding how to install your 4" Bubbler.
Flow Rate vs Plume Height for 1.5” Plumbing
40”
35”
30”
25”
20”
15”
10”
5”
10 15
4”
6”
8”
10”
12”
20
NOTICE
25 30
Flow Rate (GPM)
35
Results may vary.
4” 6” 8” 10” 12” water depth
40 45
8
MAINTENANCE INSTRUCTIONS
GENERAL MAINTENANCE INSTRUCTIONS
1
2
APPLY O-RING
LUBRICANT TO
L-GASKET BEFORE
REINSTALLING
1
2
1
2
NOTICE
• Do not damage or misplace the sealing L-Gasket that in underneath the large lens.
• To remove the LED Light Module, insert the four snaps on the
Installation Tool into the four snap receptors on the small LED lens. Use a 3/8" socket extender to insert into the square hole on the top of the
Installation Tool. Rotate counterclockwise until you feel a click. Then keep rotating until the Light Module unseals itself from the conduit. Pull the Installation Tool upwards and remove the LED Light Module.
WINTERIZING STEPS
1. Remove the eyeball from the large lens by rotating eyeball 90° and lifting out vertically.
2. Remove the large lens by inserting the top of the installation tool into the eyeball cavity like a key, then rotating counter-clockwise.
3. Remove the large lens from the floating collar using the installation tool then replace the eyeball back into the large lens for storage.
4. Remove the L-gasket that is directly below the large lens.
5. Remove the LED light module using the installation tool.
6. Secure the wire inside main body, use tape to prevent the cord from retracting back into the conduit.
7. Use an air compressor to blow the water line free of water.
8. Install the pressure test cap (25503-460-208) on the bubbler for the duration of winter.
9. Store the large lens with eyeball, L-gasket, and LED light module in a dry place for winter.
CAUTION
When removing the LED Light
Module, make sure to not let the power cable fall back down into the conduit. Use tape or a paper clip around the power cord to prevent this from happening prior to disconnecting.
9
NOTES
10
NOTES
11
TROUBLE SHOOTING/FAQ
TROUBLE SHOOTING
Problem
Large Lens is hard to install and/or remove.
Light Module is hard to install and/or remove.
Solution 1
Apply O-Ring lubricant to the top of the L-Shaped gasket under the large lens
To install, push the module down with force to seal the bottom O-Rings in the electrical conduit socket. Use the Installation Tool, a 3/8" socket wrench, and a 3/8" socket extender to help turn the Light Module clockwise until it reaches the locked position.
Solution 2
Make sure L-Gasket is properly aligned and seated in the groove.
To remove, use the Installation
Tool, a 3/8" socket wrench, and a 3/8" socket extender to turn the Light Module counterclockwise. Ramps in the Center
Wheel will help un-seal the
O-Rings from the conduit socket as it rotates.
LED Light Module flashes and then goes dark.
Make sure you are using a
12VAC transformer not 120V directly from a power outlet.
Make sure you are using a
12VAC transformer (not sold by
CMP) and not the CMP 12V DC
Power Supply (25650-110-200).
Can not pull the LED Light
Module out of the Bubbler unit.
Swirling or sloshing water
No slack was left in the line.
Provide slack on the power cable by coiling some extra wire on the control box side of the installation.
Have another person help by pushing the electric cable from the control box side of the installation.
The 4" Bubbler was installed too close to a wall or other feature in the pool which causes a harmonic wave to occur in the water. Angle the eyeball differently to change the water harmonics.
Try changing your GPM flow rate using a flow control valve.
12
LED OPERATION INSTRUCTIONS
NOTICE
When syncing multiple LED light products, color shows will match but cycle timings may vary.
CMP/J-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The CMP/J-STYLE Brilliant Wonders® 1.5" LED Light is preprogrammed with the following color sequence:
SEQUENCE ORDER
1
2
3
6
7
4
5
10
11
12
8
9
13
14
COLOR MODE
Alpine White
Sky Blue
Cobalt Blue
Caribbean Blue
Spring Green
Emerald Green
Emerald Rose
Magenta
Violet
Slow Color Splash
Fast Color Splash
America the Beautiful
Fat Tuesday
Disco Tech
To operate the light and change colors:
• Turn the light ON. The first time the light is turned on, the color sequence will begin with Alpine
White. To change color, turn light OFF then back ON within three (3) seconds. Continue turning OFF and ON until the desired light color mode is reached.
• When the light is turned off for more than seven (7) seconds, it will remain in the color mode that was currently active when the light was turned off.
• To RESET the light to the beginning color sequence (Alpine White), turn the light OFF, wait four (4) to six (6) seconds, then turn the light ON.
NOTICE
CMP Brilliant Wonders ® LED Products can be used with Jandy ® controls. Refer to operating instructions for your control box. “J-style” must be ordered for compatibility.
13
LED OPERATION INSTRUCTIONS
[CONTINUED]
H-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The H-STYLE Brilliant Wonders® 1.5" LED Light is preprogrammed with seventeen light modes:
SEQUENCE ORDER
1
2
3
6
7
4
5
12
13
14
15
8
9
10
11
16
17
COLOR MODE
Voodoo Lounge
Deep Blue Sea
Royal Blue
Afternoon Skies
Aqua Green
Emerald
Cloud White
Warm Red
Flamingo
Vivid Violet
Sangria
Twilight
Tranquility
Gemstone
USA!
Mardi Gras
Cool Cabaret
To operate the light and change colors:
• The H-STYLE Brilliant Wonders® 1.5" LED Light is operated through power-cycling; a method of changing modes which requires no special controller or interface. To activate the light simply turn the power switch ON. To advance to the next programmed light mode, turn the switch OFF then back ON within ten (10) seconds. Whenever the light has been off for more than sixty (60) seconds, and it is first turned on, it will come on white for 15 seconds, then go back to the last programmed light mode it was running before being powered off.
To sync the light with additional H-STYLE lights:
• The H-STYLE Brilliant Wonders® 1.5" LED Light can easily be synced with additional H-STYLE lights.
All lights should be wired to the same switch, this should automatically sync the lights. If the lights get out of sync on the same switch: turn the switch OFF, then wait between eleven (11) and fourteen
(14) seconds and turn the switch back ON. When the lights come back on, they should enter program mode number one (1) and be synchronized.
14
NOTICE
CMP Brilliant Wonders ® LED Products can be used with Hayward ® controls. Refer to operating instructions for your control box. “H-style” must be ordered for compatibility.
Not compatible with Hayward ® Networked Lights.
LED OPERATION INSTRUCTIONS
[CONTINUED]
P-STYLE COLOR SELECTION AND SYNC INSTRUCTIONS
The P-STYLE Brilliant Wonders® 1.5" LED Lights can be controlled using a standard wall-mount light switch. Multiple lights can be connected via a junction box to a single switch so that all lights can be switched ON and OFF together. P-STYLE Lights are controlled by cycling the AC power from a standard wall switch. By turning the switch ON and OFF a specific number of times, the light activates one of the seven (7) light show modes, fixed colors, and enables the "Hold" and "Recall" feature.
The P-STYLE Brilliant Wonders® 1.5" LED Light is preprogrammed with seven light show modes
(1-7) and five fixed color modes (8-12). For saving color effects during the "show" modes the light also includes and "Hold" and "Recall" feature (13-14).
SEQUENCE ORDER
1
2
3
6
7
8
4
5
9
10
11
12
13
14
COLOR MODE
SAm® Mode
Party Mode
Romance Mode
Caribbean Mode
American Mode
California Sunset Mode
Royal Mode
Blue
Green
Red
White
Magenta
Hold*
Recall*
Example to operate the light and change to "California Sunset" show mode:
• Turn the light switch ON and OFF six (6) times.
• During the ON/OFF switching process, no illumination will occur, then a white light will momentarily illuminate.
• The white light will immediately be followed by the selected "California Sunset" mode.
*Hold and Recall Features Example (Designed for use with a controller. Can be done manually following these steps):
• Use the "Hold" feature to capture a unique color effect while any color show is active.
• Turn switch on and off thirteen (13) times. Held color effect is activated.
• From any light show or fixed color mode...
• Turn switch ON and OFF fourteen (14) times to activate last saved color effect.
• Saved color effect is displayed.
NOTICE
CMP Brilliant Wonders ® LED Products can be used with Pentair ® controls. Refer to operating instructions for your control box. “P-style” must be ordered for compatibility.
15
AVAILABLE ACCESSORIES
25500-104-007
Brilliant Wonders® 1.5" LED Light
Installation Tool
(Included and Sold Separately)
25503-460-223
Pressure Test/Winter Cap and
O-Ring
(Included and Sold Separately)
25503-469-253
Large Lens Kit
(Included and Sold Separately)
25503-460-900 CMP/J Style
25503-460-900H H-Style
25503-460-900P P-Style
Brilliant Wonders®
4” LED Bubbler Light Module
(Included and Sold Separately)
25503-300-460
25503-301-460
25503-304-460
25503-309-460
25503-369-460
White
Gray
Black
Tan
Dark Blue
Vinyl Liner Kit
(Sold Separately)
25500-000-025
25500-000-050
25500-000-100
25500-000-150
25 ft
50 ft
100 ft
150 ft
Electric Cable
(Included and Sold Separately)
For the most recent instructions, videos and product information visit www.c-m-p.com/brilliant-wonders-4-led-bubbler
16

Public link updated
The public link to your chat has been updated.
Advertisement