Autonics CT Series Counter/Timer Datasheet PDF (1.1

Autonics CT Series Counter/Timer Datasheet PDF (1.1
CT Series
DIN W48×H48mm, W72×H36mm, W72×H72mm counter/timer
Upgraded functions
Upgrade
● Available to set 6 digits(0.00001 to 999999) prescale value
(4digit : 0.001 to 9999)
● Built-in Modbus communication function(Communication model)
● Available to set the One-Shot output time in 10ms.
(0.01sec. to 99.99sec.)
● Increase contact capacity to 5A(CTS, CTM Series)
● Available to set Count Start Point.(Initial value)
● Improved to select memory protection function in the indicator
● Added BATCH counter function(CTM Series)
● Added Counter Up-1 / Up-2 / Down-1 / Down-2 input modes
● Added Counter TOTAL / HOLD operation modes in the indicator
● Added Timer TOTAL / HOLD / On Time Display operation
modes in the indicator
● Added Timer INT2 / NFD / NFD.1 / INTG output modes
● Added Timer range 999.999s / 9999m59 / 99999.9h
Please read “Caution for your safety” in operation
manual before using.
DAQMaster(integrated device management program)
● DAQMaster is a integrated device management program for convenient
management of parameters and multiple device data monitoring.
● Visit our website (www.autonics.com) to download user manual and
integrated device management program.
< DAQMaster screen >
Item
Minimum requirements
IBM PC compatible computer with Intel Pentium
Ⅲ or above
Operating system Microsoft Windows 98/NT/XP/Vista/7
Memory
256MB or more
Hard disk
More than 1GB of free hard disk space
VGA
1024×768 or higher resolution display
Others
RS-232 serial port(9-pin), USB port
System
Ordering information
CT
6
M
-
2P
4
T
※A shaded (
) part is upgraded or added function.
Communication No mark
None
출력 회로의
수
T
RS 485
Power supply
Output
Size
Digit
Item
J-8
4
2
100-240VAC 50/60㎐
24VAC 50/60㎐ / 24-48VDC
2P
1P
I
Dual preset
Single preset
Indicator
S
DIN W48×H48mm
Y
M
DIN W72×H36mm
DIN W72×H72mm
4
6
9999(4digit)
999999(6digit)
CT
Counter/Timer
※4digit type does not exist
in the indicator type.
Programmable Counter/Timer
Specifications
CTS
CTY
4
6
6
CT6S-2P
CT6Y-2P
Dual Preset
CT4S-2P
CT6S-1P
CT6Y-1P
Single Preset
CT4S-1P
Model
Single Preset
CT6S-1
CT6Y-1
Single Preset
11mm
10mm
10mm
Digit
Size
Single Preset
8mm
7mm
7mm
Single Preset
100-240VAC 50/60Hz
Power
Supply
Single Preset
24VAC 50/60Hz / 24-48VDC
Allowable voltage range
90 to 110% of rated voltage(AC Power type)
Single Preset
Max. 12VA
Power
consumption Single Preset
AC: Max. 10VA / DC: Max. 8W
INA/INB Max. counting speed Selectable 1cps / 30cps / 1kcps / 5kcps / 10kcps
Counter
Reset signal : Selectable 1ms, 20ms
Min. input
signal width Timer
INA, INB RESET : Selectable 1ms, 20ms
Series
Digit
(A)
Photo
electric
sensor
CTM
6
CT6M-2P
CT6M-1P
CT6M-1
13mm
9mm
(B)
Fiber
optic
sensor
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
INA, INH, RESET, INHIBIT, BATCH
RESET : Selectable 1ms, 20ms
Selectable voltage input or No-voltage input
Input
[Voltage input] Input impedance is 5.4kΩ, 'H' level : 5-30VDC, 'L' level : 0-2VDC
[No-voltage input] Short-circuit impedance : Max. 1kΩ, Residual voltage : Max. 2VDC
One-shot output
Count, timer : Selectable 0.01s to 99.99s
Contact
Dual preset : SPST(1a) 2EA
Dual preset : SPST(1a) 1EA, SPDT(1c) 1EA
With- output
Single preset : SPDT(1c) 1EA
Single preset : SPDT(1c) 1EA
out
Dual preset:3NPN open collector
com. Solid state Dual preset : 1NPN open collector
output
Single preset : 1NPN open collector
Single preset:2NPN open collector
Contact
Dual preset : SPST(1a)2EA
Dual preset: SPST(1a), SPDT(1c)
With- output
Single preset : SPDT(1c)1EA
Single preset: SPDT(1c)
Control
out
output
Dual preset: Dual preset:2NPN open collector
com. Solid state output
Single preset:1NPN open collector Single preset:2NPN open collector
Contact
250VAC 5A resistive load
250VAC 3A resistive load
250VAC 5A resistive load
With- output
out
com. Solid state 30VDC Max. 100mA Max.
output
External sensor power
12VDC ±10%, 100mA Max.
Memory retention
10years(When using non-volatile semiconductor memory type)
Repeat error
SET error
Power ON Start : Max. ±0.01% ±0.05 sec
Timer
Signal Start : Max. ±0.01% ±0.03 sec
Voltage error
Temperature error
Insulation resistance
Min. 100MΩ(500VDC Megger)
Dielectric strength
2,000VAC 50/60Hz for 1minute
Noise strength (AC Power)
±2kV the square wave noise(pulse width:1㎲) by the noise simulator
Mechanical
0.75mm amplitude at frequency of 10 to 55(for 1 min.)Hz in each of X, Y, Z directions for 1 hour
Vibration
Malfunction
0.5mm amplitude at frequency of 10 to 55Hz(for 1 min.) in each of X, Y, Z directions for 10 minutes
Mechanical
300m/s²(approx. 30G) in each of X, Y, Z directions for 3 times
Shock
Malfunction
100m/s²(approx. 10G) in each of X, Y, Z directions for 3 times
Mechanical
Min. 10,000,000 operations
Relay
Life cycle
Electrical
Min. 100,000 operations
Protection
IP65(Front panel only)
Ambient
-10 to 55℃, storage : -25 to 65℃
temperature
Environment
Ambient
35 to 85%RH, storage : 35 to 85%RH
humidity
Approval
Unit weight
Approx. 159g
Approx. 149g
Approx. 253g
※Environment resistance is rated at no freezing or condensation.
Communication specification
Protocol
Connection method
Application standard
Number of connections
Communication method
Synchronous method
Communication distance
Communication speed
Response waiting time
Start bit
Data bit
Parity bit
Stop bit
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
Modbus RTU(16bit CRC)
RS485
Compliance with EIA RS485
31, it is available to set address 1 to 127
Half Duplex
Asynchronous
within max. 800meter
2,400/4,800/9,600/19,200/38,400bps(Factory default : 9,600bps)
5 to 99ms(Factory default : 20ms)
1bit(Fixed)
8bits(Fixed)
None, Even, Odd(Factory default : None)
1, 2bit(Factory default : 2bit)
(T)
Software
(U)
Other
J-9
CT Series
Connections
Be careful that connections are different
between communication model and
non-communication model when wiring.
CT S-2P
CT S-2P T
12VDC 100mA
INB / INH
INA
12VDC 100mA
INB / INH
INA
RESET
0VDC
OUT2
30VDC
100mA
OUT2
250VAC 5A
RESISTIVE
OUT1
250VAC 5A
RESISTIVE
-
A(+)
RESET
0VDC
RS485
B(-)
OUT2
OUT1
250VAC 5A 250VAC 5A
RESISTIVE RESISTIVE
+
※1
CT S-1P
-
+
※1
CT S-1P T
12VDC 100mA
INB / INH
INA
12VDC 100mA
INB / INH
INA
RESET
0VDC
OUT
30VDC
100mA
OUT
NO COM
NC
-
+
250VAC 5A
RESISTIVE LOAD
RESET
0VDC
A(+)
OUT
RS485
NO COM
NC
B(-)
-
250VAC 5A
RESISTIVE LOAD
※1
CT6S-I
+
※1
CT6S-I T
12VDC 100mA
INB / INH
INA
12VDC 100mA
INB / INH
INA
RESET
0VDC
RS485
A(+)
-
RESET
0VDC
B(-)
-
+
+
※1
CT6Y-2P
※1
SOLID
250VAC 3A
250VAC 3A
STATE OUT
RESISTIVE LOAD RESISTIVE LOAD 30VDC
100mA
NC COM
OUT
NO
OUT1
OUT2
0VDC RESET
INA
INB / INH
12VDC 100mA
OUT2
-
※1
CT6Y-1P
250VAC 3A
RESISTIVE LOAD
NC COM
NO
SOLID
STATE OUT
30VDC
100mA
J-10
250VAC 3A
RESISTIVE
250VAC 3A
RESISTIVE
OUT2
OUT1
0VDC RESET
-
※1
B(-)
RS485
-
+
※1
CT6Y-1P T
SOLID
250VAC 3A STATE OUT
RESISTIVE LOAD 30VDC
NC COM
NO 100mA A(+)
OUT
+
A(+)
0VDC RESET
INA
INB / INH
12VDC 100mA
OUT
OUT
INA
INB / INH
12VDC 100mA
+
CT6Y-2P T
INA
INB / INH
12VDC 100mA
OUT
0VDC RESET
B(-)
RS485
-
+
※1
Programmable Counter/Timer
CT6Y-I
CT6Y-I T
(A)
Photo
electric
sensor
B(-)
A(+)
RS485
-
0VDC RESET
INA
INB / INH
12VDC 100mA
+
※1
CT6M-2P
BATCH RESET
SOLID STATE OUT
30VDC
100mA
CT6M-1P
※2
INHIBIT
RESET
0VDC
12VDC 100mA
INB
INA
+
B(-)
※1
OUT
COM NC
NO
250VAC 5A
RESISTIVE
LOAD
12VDC 100mA
INB
INA
-
(I)
SSR/
Power
controller
+
(J)
Counter
※1
BATCH RESET
(K)
Timer
※2
INHIBIT
RESET
0VDC
BATCH RESET
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
RS485
BATCH
B(-)
OUT
BATCH
(N)
Display
unit
SOLID STATE OUT
30VDC
OUT
100mA
OUT
CT6M-I
(H)
Temp.
controller
CT6M-1P T
12VDC 100mA
INB
INA
A(+)
NO COM NO
250VAC 5A
RESISTIVE
LOAD
OUT2 BATCH
SOLID STATE OUT
30VDC
OUT2
100mA
NO COM
250VAC 5A
RESISTIVE
LOAD
SOLID STATE OUT 30VDC
100mA
OUTPUT
COMMON
(F)
Rotary
encoder
(G)
Connector/
Socket
OUT1
-
BATCH RESET
RS485
OUT2
COM NC
NO
250VAC 5A
RESISTIVE
LOAD
(D)
Proximity
sensor
(E)
Pressure
sensor
※2
INHIBIT
RESET
0VDC
12VDC 100mA
INB
INA
A(+)
NO COM
250VAC 5A
RESISTIVE
LOAD
+
※1
OUTPUT
COMMON OUT1 OUT2 BATCH
OUT1
-
(C)
Door/Area
sensor
CT6M-2P T
※2
INHIBIT
RESET
0VDC
12VDC 100mA
INB
INA
0VDC RESET
INA
INB / INH
12VDC 100mA
(B)
Fiber
optic
sensor
-
NO COM NO
250VAC 5A
RESISTIVE
LOAD
+
※1
CT6M-I T
※2
INHIBIT
RESET
0VDC
-
(O)
Sensor
controller
(P)
Switching
mode power
supply
+
※1
(Q)
Stepper
motor&
Driver&Controller
※2
INHIBIT
RESET
0VDC
12VDC 100mA
INB
INA
(R)
Graphic/
Logic
panel
(S)
Field
network
device
RS485
A(+)
(T)
Software
B(-)
(U)
Other
-
+
※1
※1: Source
- AC Power: 100-240VAC 50/60Hz
- AC/DC Power: 24-48VDC, 24VAC 50/60Hz
-
+
※1
※2: INHIBIT Signal
- Counter operation: If INHIBIT signal is applied,
count input will be prohibited.
- Timer operation: If INHIBIT signal is applied, time
progressing will stop.(HOLD)
J-11
CT Series
Dimensions
(unit:mm)
CTS Series
● Bracket
10
48
● Panel cut-out
90
2
5
4
8
7
4
5
10
3
9
6
2
10
J-12
31.5 +0.6
0
68 +0.7
0
CTM Series
1
6
13
3
7
8
2
5
4
12
11 9
10
9. Mode key
- By pressing MD key for 3sec (parameter setting)/ 5sec (communication)
in RUN mode, it moves to function setting mode.
- By pressing MD key in function setting mode, select function setting
mode. By pressing MD key over 3 sec., it moves to Run mode.
- By pressing MD key over 1 sec. in function setting checking mode, it
moves to Run mode.
10. Set key
≪ : To enter into setting value(PS1, PS2) change status and shift digit
of setting value(PS1, PS2).
: To decrease setting value in setting value change mode, change
setting value in function setting mode, move down checked
value in function setting check mode.
: To increase setting value in setting value change mode, change
setting value in function setting mode, move up checked value in
function setting check mode. By pressing MD key over 1 sec.
in Run mode, enters into function setting check mode.
11. BATCH key
By pressing BA key in run mode to enter into BATCH counter
indication mode.
12. BATCH output indicator(red LED)
13. BATCH setting value checking and changing indicator
(yellow-green LED)
Lights when checking and changing BATCH setting value.
≫
Model
Changed Notice
1. Count indicator(Red LED)
CT6Y-1P
- Run mode
CT6S-1P PS2→PS There are no
PS1, OUT1
: Count mode-Indicates count value.
CT4S-1P OUT2→OUT LEDs.
Timer mode-Indicates time progressing. CT6M-1P
CT6Y-I
- Function setting mode
There are no
CT6S-I
PS2→PS PS1, OUT1
: Indicates function setting mode.
OUT2 LEDs.
CT6M-I
2. Preset value indicator (Yellow-Green LED)
※The indicator type does not exist
- Run mode: Indicates preset value.
in CT4S model.
- Function setting mode: Indicates setting value1.
3. Key Lock : Lights when setting key lock.
4. The operation of counter indicator
5. The operation of timer indicator
TMR LED flashes when the timer is operating.
TMR LED lights when the operating time stops.
6. Check preset value and display change of it
PS1 LED lights when checking or changing the setting value1.
PS2 LED lights when checking or changing the setting value2.
7. Output(OUT1, OUT2) indicator
OUT1 lights when output1 is on.
OUT2 lights when output2 is on.
8. Reset key
By pressing RST key in Run mode, the count value is initialized and
output is returned.
By pressing RST key in BATCH counter mode,BATCH count value
resets.
≫
6
3
7
8
9
1
68 +0.7
0
Min. 91
67
1
CTY Series
68 +0.7
0
● Panel cut-out
85
10
72
Min. 40
30
36
86
Parts description
45.5 +0.5
0
Min. 91
77
6
72
CTS Series
45.5 +0.5
0
● Panel cut-out
85
CTM Series
Min. 62
Min. 91
CTY Series
45
60
Min. 55
Programmable Counter/Timer
Input connections
(A)
Photo
electric
sensor
No-voltage input(NPN)
● Solid-state input(Standard sensor : NPN output type sensor)
Sensor
Brown
Black ※1
Counter/Timer
CT Series
Sensor
+12V
5.4Ω
+12V
(NPN output)
(C)
Door/Area
sensor
+12V
Inner circuit
of input part
Blue
0V
Counter/Timer
CT Series
5.4Ω
Black ※1
Inner circuit
of input part
Blue
Counter/Timer
CT Series
Brown
(B)
Fiber
optic
sensor
● Contact input
※2
5.4Ω
(D)
Proximity
sensor
Inner circuit
of input part
0V
(E)
Pressure
sensor
0V
(NPN open collector output)
(F)
Rotary
encoder
※1: INA, INB/INH, RESET, INHIBIT, BATCH RESET input part
※2: Counting speed: 1 or 30cps setting(Counter)
(G)
Connector/
Socket
Voltage input(PNP)
● Solid-state input(Standard sensor : PNP output type sensor)
Sensor
Brown
Counter/Timer
CT Series
+12V
Black ※1
Blue
Sensor
Counter/Timer
CT Series
Brown
5.4㏀
(PNP output)
Counter/Timer
CT Series
(I)
SSR/
Power
controller
+12V
Inner circuit
of input part
(J)
Counter
Inner circuit
of input part
5.4㏀
Blue
0V
※2
+12V
Black※1
Inner circuit
of input part
(H)
Temp.
controller
● Contact input
5.4Ω
0V
(K)
Timer
0V
(PNP open collector output)
(L)
Panel
meter
※1: INA, INB/INH, RESET, INHIBIT, BATCH RESET input part
※2: Counting speed: 1 or 30cps setting(Counter)
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
Input logic Selection[No-voltage input(NPN)/Voltage input(PNP)]
1. The power must be cut off.
2. Detach the case from the body.
(CTS, CTY Series)
①
②
3. Select input logic by using input logic switch(SW1)
inside Counter/Timer.
(O)
Sensor
controller
● Select No-voltage
input(NPN)
(P)
Switching
mode power
supply
NPN PNP
(Factory default)
● Select voltage
input(PNP)
NPN
(Q)
Stepper
motor&
Driver&Controller
PNP
(R)
Graphic/
Logic
panel
(S)
Field
network
device
①
* Case detachment
Squeeze toward ① and pull toward ② as shown
in picture.
Please check if the power is cut off.
(T)
Software
<CTS Series>
<CTY Series>
<CTM Series>
(U)
Other
4. Push a case in the opposite direction of 2-②.
5. Then apply the power to Counter/Timer.
J-13
CT Series
Output connections
Contact output
Solid-state output
Counter/Timer
CT Series
Counter/Timer
CT Series
※1
Load
(Power of load)
(-)
Load
Communication
Timer
Counter
Factory default
Factory default
UP/Down-C (UD-C)
F (F)
30cps (30)
TOTAL (TOTAL)
Hold (HOLD)
100ms (0)10)
------
20ms (20)
NPN (NPN)
6digit type : -.-----, 4digit type : -.---­
6digit type : 1.00000,4digit type : 1.000
000000
Clear (SLR)
Lock off (lOFF)
1000 (1000)
5000 (5000)
6Digit type: 0.001s-999.999s, 4Digit type: 0.001s-9.999s
UP (UP)
TOTAL (TOTAL)
CLEAR (SLR)
OND (OND)
Hold (HOLD)
100ms (0)10)
NPN (NPN)
20ms (20)
Lock off (lOFF)
1000 (1000)
5000 (5000)
01 (001)
9600bps (96)
NONE (NONE)
2 (2)
20ms (20)
Enable (ENA)
Error display
Error display
EEP
PS1○
PS2○
J-14
FAIL
Power
for load
(DC)
※Use proper load and power for load not to excess ON/OFF
capacity(30VDC Max. 100mA max.) of solid state output.
※Be sure not to apply reverse polarity of power.
※1: When use inductive load(Relay etc), surge absorber
(Diode, varistor etc) must be connected between both
sides of the load.
※Use proper load not to exceed the capacity.
Parameter
Input mode (ㅑIN)
Output mode (OUtM)
CPS (CPS)
Indication mode (indicator type)(DSpM)
OUT2 output time (OUt2)
OUT1 output time (OUt1)
Decimal point (DP)
Min. reset time (RST)
Input logic (SIG)
Prescale decimal point (ScDP)
Prescale value (SCL)
Start Point setting (STRT)
Counting memory (DATA)
Lock key (LOCK)
Preset value 1 (PS1)
Preset value 2 (PS2)
Time range (HOUR/MIN/SEC)
Up/Down mode (U-D)
Indication mode(Indicator type)(DSpM)
Memory protection(Indicator type) (DATA)
Output mode (OUtM)
OUT2 output time (OUT2)
OUT1 output time (OUT1)
Input logic (SIG)
Input signal time (ImT)
Lock key (LOCK)
Preset value 1 (PS1)
Preset value 2 (PS2)
Communication address (ADDR)
Communication speed (BPS)
Communication parity (PRTY)
Communication stop bit (STP)
Response waiting time (RSWT)
Communication writing (COmY)
(+)
Errors
Output status
How to return
Failed in data loading
for exsiting setting
values
OFF
Power on again
Programmable Counter/Timer
Operations and functions
RESET
BATCH RESET
※1
Change of BATCH
setting value.
(A)
Photo
electric
sensor
※1
Change of
preset
RUN
mode
BATCH counter
indication mode
※BATCH counter is
available for
CT6M-1P/2P only.
3sec. 5sec.
※1. If no key is touched for 60 sec., the counter will
return to RUN mode without being restored.
1sec.
1sec.
(B)
Fiber
optic
sensor
Function setting
check mode
(C)
Door/Area
sensor
(D)
Proximity
sensor
3sec.
3sec.: Enters into parameter 1 group
5sec.: Enters into parameter 2 group
Function
setting mode
(F)
Rotary
encoder
Change of preset(Counter/Timer)
●Even if changing the preset value, input operation and output control will continue. In addition, the preset value could
be set to 0 and 0 preset value turns ON. According to output mode, preset value could not be set to 0. (When setting to 0,
preset value "0" will flash 3 times.)
1.
2.
(E)
Pressure
sensor
(G)
Connector/
Socket
3.
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
In Run mode, it enters into the
preset value setting mode
using
key. 'PS1' LED lights
and first digit of preset value
flashes.
The preset value is set to ' '
using ,
and
keys, then
press
key to enter into the
PS2 setting mode.
(K)
Timer
The preset value is set to '200'
using ,
and
keys, then
press
key to complete PS2
setting and return to Run mode.
(L)
Panel
meter
※Press key to save set value after changing the setting value. Then, it moves to next parameter or returns
to RUN mode. However, if no key is touched for 60 sec., it will return to RUN mode without being saved.
Function setting check mode
● Setting value of function setting mode can be confirmed using the
and
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
keys.
Switching display function in preset indicator
●Setting value 1(PS1) and setting value 2(PS2) are displayed each time pressing
(In timer, it is available for
output mode.)
(O)
Sensor
controller
key in dual preset model.
(P)
Switching
mode power
supply
Reset
● In Run mode or function setting mode, if
key or applying the signal to the RESET terminal on the back side,
present value will be initialized and output will maintain off status. When selecting voltage input(PNP), short no. 10
and no. 12 terminals, or when selecting no-voltage input(NPN), short no. 11 and no. 12 terminals to reset.
BATCH Counter(For CT6M-1P
/CT6M-2P
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
model only)
In BATCH counter indication mode, 'BATCH counter value' is displayed in count indicator and 'BATCH counter
setting value' is displayed in preset indicator.
(S)
Field
network
device
Change of BATCH setting value
If pressing
key in Run mode, it will enter into BATCH counter indication mode.
1.
(T)
Software
2.
It enters into
settingvalue change
mode using key.
(BA.S lights, first digit
of setting value flashes.)
(U)
Other
BATCH value is set to '200'
using , and keys,
then press key to complete
BATCH setting value and
move to BATCH counter
indication mode.
J-15
CT Series
BATCH counter operation
Power
ON
OFF
Preset output
Batch Reset
999999
Batch setting value
0
BA.O LED
ON
OFF
Batch ON
output OFF
BATCH counting operation
● BATCH counting value is increasing until BATCH reset signal applied. BATCH counting value will be circulated when it is
over 999999.
1) BATCH counting operation in Counter : Counts the number of reaching setting value of CT6M-1P or reaching dual
setting value of CT6M-2P
2) BATCH counting operation in Timer: Counts the number of reaching setting time.
(In case of "FLK" output mode, count the number of reaching T.off setting time
and T.on setting time.)
BATCH output
● If input signal is applied while changing BATCH setting value, counting operation and output control will be performed.
● If BATCH count value equals to BATCH setting value, BATCH output will be ON and maintain ON status until BATCH reset
signal is applied.
● When the power is cut off then resupplied in status of BATCH output is ON, BATCH output maintains ON status until
BATCH reset signal is applied.
BATCH reset input
● If pressing reset button or applying the signal to BATCH reset terminal on the back side panel, BATCH counting value will
be reset. When selecting voltage input(PNP), short no. 10 and no. 14 terminals, or when selecting no-voltage input(NPN),
short no. 11 and no. 14 terminals to reset.
● When BATCH reset is applied, BATCH counting value maintains at 0 and BATCH output maintains in the OFF status.
Application of BATCH counter function
● Counter
In case, put 5 products in a box then pack the boxes when
they reaches to 200.
- Counter preset setting value="5", BATCH setting
value="200"
- When the count value of counter reaches to the preset
value "5", the control output(OUT) will be on, and at
this time the count value of the BATCH counter will be
increased by "1". The control box which is received the
control output (OUT) repeatedly controls conveyor to
move the full box and to place the next empty box for
standby. When the BATCH count value reaches to "200",
BATCH output will be ON. Then the control box stops
conveyor and provides a control signal for packing.
Count input
BATCH output
Control
output
(OUT)
CT6M-1P4
Control box
Preset value = 5
BATCH output
lamp
Control signal
for packing
Control signal
for conveyor
Third
Second
First
box
box
box
Current BATCH count value = 3
J-16
● Timer
Fills milk into the bottle for 3sec.(setting time) When 500
bottles are filled, BATCH counting finish lamp is turned on.
(Setting time : 3sec., BATCH setting value : 500)
Operation valve
(Open valve
for 3sec.)
BATCH output
Control
output
CT6M1P4
Control the
operation valve
Bottle sensing
sensor
Productivity :
500bottels
Lamp on when
it is completed.
BATCH counting
finish lamp
Control
box
Programmable Counter/Timer
Flow chart for function setting mode
(A)
Photo
electric
sensor
Run mode
3sec.
3sec.
5sec.
Parameter group1
,
※3
Counter/Timer
(COUN)
(GRp2)
(C-T)
Input mode
Time range
(IN)
※3
Output mode
(ㅐㅕㅆOUtM)
Indication mode
※1
(DSpM)
※3
Max. counting speed
(CPS)
※2 ※3
Function setting mode
OUT2 output time
(OUT2)
※3
OUT1 output time
(OUT1)
※3
Decimal point
(DP)
※3
(HOUR/MIN/SEC)
※2
(RST)
Up/Down mode
(U-D)
※1
※3
Indication mode
(DSpM)
Memorize
counting value
(DATA)
※3
Output mode
(OUtM)
※3
OUT2 output time
(OUT2)
※3
(OUT1)
Input logic
(SIG)
(SIG)
※3
Prescale decimal
point
(ScDP)
※3
Prescale value
(RST)
※3
Start Point value
(STRT)
Memorize counting value
(LOCK)
Communication
(E)
Pressure
sensor
Com. address
(ADDR)
※3
Input logic
Lock key
(D)
Proximity
sensor
(F)
Rotary
encoder
Com. speed
(BPS)
(G)
Connector/
Socket
Com. parity
(PRTY)
(H)
Temp.
controller
Com. stop bit
(I)
SSR/
Power
controller
(STP)
Response
waiting time
(J)
Counter
(RSwT)
(K)
Timer
Com. writing
(COmW)
(L)
Panel
meter
OUT1 output time
Min. reset time
(DATA)
(C)
Door/Area
sensor
Timer
(T1ME)
※3
3sec.
Parameter group2
(GRp1)
Counter
(B)
Fiber
optic
sensor
Input signal time
(InT)
※1: Indicator
※2: Output type
※3: If changing the setting
value of function, OUT1,
OUT2 will turn OFF and
return to Run mode, then
present value resets.
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
Lock key
(LOCK)
(P)
Switching
mode power
supply
※Counter
- Single preset model has no "OUT1 output setting time" setting function
mode and OUtT is displayed in "OUT2 output time" setting function mode.
- In case of DN, DN-1, DN-2 input mode, there is no "Start Point value" setting
function mode.
- In case of F or N output mode, there is no "OUT2 output time" setting function
mode.(Fixed to HOLD)
- In case of S, T or D output mode, there is no "OUT2 output time" setting
function mode.
※Timer
- In case of FLk1, FLk2 or INtG output mode and OND, OND1, OND2 output
mode of single preset model, OUtT is displayed in "OUT2 output time" function
setting mode and there is no "OUT1 output time" function setting mode.
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
- The output modes except for OND, ONd1, ONd2 and INt2 output mode there is no
"OUT1 output time" function setting mode.
※If changing setting value of parameter group1, display value and output will be initialize.
※Press key over 3sec./5sec. in RUN mode to enter into parameter 1 group/ parameter 2 group.
Press key over 3 sec. in function setting mode to return RUN mode.
※Input operation and output control can be set in function setting mode.
※If changing set value of ※3 marked parameters in function setting mode, OUT1 and OUT2 output will be turned OFF and
then the current value is reset.
※Parameter 2 group is not available to non-communication models.
J-17
(U)
Other
CT Series
Parameter setting(Counter)
(
Setting mode
How to set
Counter/Timer
ㅊㅊC-T
COUN
Input mode
IN
UD-C
key: To select setting mode,
key: To change setting value)
※CONE: COUNTER
TIME: TIMER
TIME
UP
or
UP-1
UP-2
DN
DN-1
DN-2
UD-A
UD-B
● UP, UP-1, UP-2 or DN, DN-1, DN-2 input mode
N
F
C
R
K
P
Q
A
Output mode
OUtM
Indication mode
DSpM
Max. counting speed
CPS
※In case that output mode is F, N there is no "OUT2 output time" setting mode. (Fixed to HOLD)
※If output mode is set to D when max. counting
● UD-A, UD-B, UD-C input mode
N
F
C
R
K
P
Q
A
S
T
D speed is set to 5Kcps, 10Kcps, max. counting
speed is automatically set to 30cps. (Factory
default setting)
● In case of the indicator
※In case of the indicator, indicate mode selection (DSpM)is displayed.
HOLD
TOTAL
※It is added that the function which can set the preset value when selecting
HOLD.(Refer to J-22 page 'Counter operation of the indicator'.)
30
1K
SY
10K
1
※Counting speed is that of one by one(1:1) duty ratio of INA or INB input signal,
and it is applied in INA and INB at thesame time.
※In case of setting D in output mode, you can choose 1cps, 30cps, 1Kcps.
OUT2 output time
OUT2
: To shift flashing digit position of OUT2
output time value.
: To change OUT2 output time value.
OUT1 output time
OUT1
: To shift flashing digit position of OUT1
output time value.
: To change OUT1 output time value.
※1
Decimal point
DP
● 6digit type
------
-----.-
● 4digit type
------.-
--.--
Min. reset time
RST
1
Input logic
SIG
NPN: No-Voltage input
PNP: Voltage input
※1
Prescale
decimal point
ScDP
20
----.--.---
※Set OUT2 one-shot output time.
※Setting range: 0.01 to 99.99 sec.
※It does not appear if F, N output mode is selected.
※Set OUT1 one-shot setting time
※Time range: 0.01 to 99.99 sec., Hold
※HOLD is displayed by pressing key 4 times.
---.---
--.----
-.-----
※Setting the decimal point is applied same to counting
value and setting value.
※Set the min. external RESET signal width.
unit: ms
※Check input logic value(PNP, NPN).
● 6digit type
※Prescale decimal point position is not set below the decimal
point setting digits (DP).
● 4digit type
Prescale value
SCL
: To shift the flashing digit.
: To change the prescale value.
※Setting range of prescale value
6digit type: 0.00001 to 99999.9
4digit type: 0.001 to 999.9
※Refer to the J-20 page ' Prescale function'.
Start Point Value
STRT
: To shift the flashing digit.
: To change the Start Point value.
※Setting range of Start Point value (Connected with decimal point setting)
6digit type: 0.00000 to 999999
4digit type: 0.000 to 9999
※Refer to the J-20 page ' Start Point function'.
Memory protection
DATA
Lock key
LOCK
CLR
REC
LOFF
LOc1
LOc3
LOc2
※CLR: Initializes count value when power is off.
※REC : Memorizes count value at the moment of power off.
※LOFF:Cancellation of the lock mode.
LOc1: Locks
key.
LOc2: Locks , , keys.
LOc3: Locks , , , keys.
※1. Explanation of decimal point and prescale decimal point setting
- Decimal point setting : Set decimal point of the display value on front indicator.
- Prescale decimal point setting : Set prescale decimal point of counting regardless of decimal point of display value
on front indicator.
J-18
Programmable Counter/Timer
Input operation mode(Counter)
Input mode
Count chart
Operation
INA H
H
INB
L
No
counting
(UP)
Count
0
value 0
H
INA
L
UP-1
Ⓐ
Ⓐ
INB H
L
Count
value 0
0
Ⓐ
n-1
n-2
INA H
L
DN-1
(Down-1)
Count
value
INA
DN-2
Ⓐ
n
n-1
(Up/Down-A)
Count
value
n-5
n-6
(H)
Temp.
controller
(I)
SSR/
Power
controller
Ⓐ
n
n-4
0
1
2
3
4
n-4
2
1
(Q)
Stepper
motor&
Driver&Controller
2
(R)
Graphic/
Logic
panel
n-5
Ⓐ
3
(O)
Sensor
controller
※Counts when INA input signal is
down. (
)
※INA: Counting input
※INB: Inhibition input
n-3
Ⓐ
(N)
Display
unit
(P)
Switching
mode power
supply
Ⓐ
n-2
H
L
(M)
Tacho/
Speed/ Pulse
meter
n-5
No counting
n-1
(L)
Panel
meter
※Count when INA input signal is up.
(
)
※INA: Counting input
※INB: Inhibition input
n-3
Ⓐ
(K)
Timer
n-7
0
0
(G)
Connector/
Socket
※If INA is counting input, INB is
inhibition input.
If INB is counting input, INA is
inhibition input.
No counting
n-2
H
INA L
INB
n-4
Ⓐ
H
L
INB H
L
Count
value
n-3
0
(Down-2)
UD-A
Ⓐ
0
INB H
L
(F)
Rotary
encoder
No counting
Ⓐ
n
Count
value
(D)
Proximity
sensor
(J)
Counter
INB H
L
(Down)
(C)
Door/Area
sensor
※Counts when INA input signal is
down. (
)
※INA: Counting input
※INB: Inhibition input
4
3
2
1
INA H
L
DN
Ⓐ
No counting
(Up-2)
※If INA is counting input, INB is
inhibition input.
If INB is counting input, INA is
inhibition input.
※Counts when INA input signal is up.
(
)
※INA: Counting input
※INB: Inhibition input
5
4
3
INA H
L
UP-2
Ⓐ
2
1
0 0
7
(E)
Pressure
sensor
No counting
(Up-1)
6
5
4
3
2
1
H
INB L
Count
value
(B)
Fiber
optic
sensor
No counting
L
UP
(A)
Photo
electric
sensor
3
4
(S)
Field
network
device
※INA: Counting input
INB: Counting command input
(T)
Software
※When INB is L, counting Up.
When INB is H, counting Down.
(U)
Other
J-19
CT Series
Input operation mode(Counter)
Input mode
Count chart
Operation
INA H
L
INB H
L
ㅕㅕUD-B
(Up/Down-B)
Count
value
0
INA H
L
INB H
L
UD-C
2
1
0
0
4
3
2
2
3
4
BBBB
(Up/Down-C)
Count
value
3
0
1
2
3
2
1
2
3
※INA: Up counting input
INB: Down counting input
※When both INA and INB are applied
to L->H, it will remain previous
counting value.
※When use A,B phase of encoder
with connecting to INA, INB, please
set counter input mode(IN) as
phase different input(UD-C).
※ⓐ signal width should be over min. signal width and ⓑ signal width should be over a half min. signal width.
If not, ±1 will occur.
※Min. signal width by counting speed
※The meaning of "H" and "L"
Voltage input (NPN) No-Voltage input (PNP)
H
5-30VDC
Short circuit
L
0-2VDC
Open
Counting
speed
1cps
30cps
1kcps
5kcps
10kcps
Min. signal
width
500㎳
16.7㎳
0.5㎳
0.1㎳
0.05㎳
INA High
(INB) Low
ON
OFF
Ton
Toff
ON
OFF
T
※Ton, Toff : Min. signal width
Prescale function(Counter)
This function is to set and indicate calculated unit for actual length, liquid measure, position etc. It is called "Prescale value"
for measured length, measured liquid, measured position, etc per 1 pulse.
For example, P is the number of pulses per 1 revolution of a rotary encoder and L is the desired length to be measured.
Prescale value is [the desired length (L)]/[the number of pulses (P) per 1 revolution of the rotary encoder.].
It is the length per 1 pulse of a rotary encoder.
Ex) Control length by the counter and the rotary encoder
Roller
[In case of 22mm diameter(D) of roller connected
with the encoder of 1,000 pulse]
Cutter
Rotary encoder
● Prescale value =
Motor
Motor controlling
system
=
Counter
π × Diameter of the roller(D)
The number of pulses per
1 revolution of the encoder
3.1416 × 22
1000
= 0.069mm/pulse
To control conveyor position in 0.1mm, set the decimal point to tenth place(-----.-) in decimal point setting mode(DP) and
set the prescale decimal point to thousandth place(---.---) in prescale decimal point setting mode(ScDP)Then set prescale
value "0.069" in prescale setting mode (SCL).
Start point function(Counter)
This function is that start point value works as initial value when on counting mode.
● In case of DN, DN-1 or DN-2 in timer input mode, it is not available.
● When reset is applied, the present value is initialized to start point.
● After count up in C, R, P, Q After count up in
J-20
Programmable Counter/Timer
Output operation mode(Counter)
Output
mode
F
(F)
One-shot output(0.01 to 99.99 sec.)
One-shot output Retained output
Retained output
Input mode
Up, Up-1, 2
Down, Down-1, 2
Up/Down A, B, C
RESET
999999
PRESET2
PRESET1
0
OUT1
OUT2
(OUT)
N
(N)
C
(C)
RESET
999999
PRESET2
PRESET 1
0
OUT1
OUT2
(OUT)
RESET
999999
PRESET2
PRESET 1
0
OUT1
OUT2
(OUT)
R
(R)
K
(K)
P
(P)
RESET
999999
PRESET2
PRESET1
0
OUT1
OUT2
(OUT)
RESET
999999
PRESET2
PRESET1
0
OUT1
OUT2
(OUT)
RESET
999999
PRESET2
PRESET1
0
OUT1
OUT2
(OUT)
Q
(Q)
RESET
999999
PRESET2
PRESET1
0
OUT1
OUT2
(OUT)
A
(A)
RESET
999999
PRESET2
PRESET 1
0
OUT1
OUT2
(OUT)
(A)
Photo
electric
sensor
(B)
Fiber
optic
sensor
Operation
※After count-up, counting display
value increases or decreases until
reset signal is applied and retained
output is maintained.
(C)
Door/Area
sensor
(D)
Proximity
sensor
(E)
Pressure
sensor
※After count- up, counting display
value and retained output are maintained until reset signal is applied.
(F)
Rotary
encoder
(G)
Connector/
Socket
※When count-up, counting display value
will be reset and count simultaneously.
※OUT1 retained output will be off after
OUT2 one- shot time.
※The one-shot output time of OUT1
one-shot output time is operated
gardless of OUT2 output.
※After OUT2 one-shot time, counting
display value will be reset and count
simultaneously.
※OUT1 retained output will be off after
OUT2 one-shot time.
※OUT1 one-shot output time is operated
regardless of OUT2 output.
※After count-up, counting display
value increases or decreases until
RESET input is applied.
※OUT1 retained output is off after
OUT2 one-shot time.
※OUT1 one-shot output time is operated
regardless of OUT2 output.
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
※After count-up, counting display value is
maintained while OUT2 output is on.
Counting value is internally reset and
counts simultaneously.
※When OUT2 output is off, displays
counting value while OUT2 is ON,
and it increases or decreases.
※OUT1 retained output is off after
OUT2 one-shot time.
※OUT1 one-shot output time is operated regardless of OUT2 output.
(O)
Sensor
controller
※After count-up, counting display
value increases or decreases during
OUT2 one-shot time.
※OUT1 retained output is off after
OUT2 one-shot time.
※OUT1 one-shot output time is operated
regardless of OUT2 output.
(R)
Graphic/
Logic
panel
※After count-up, counting display value
and OUT1 retained output are maintained until RESET input is applied.
※OUT1 one-shot output time is operated regardless of OUT2 output.
※The single preset type output(OUT) is operated as OUT2 of dual preset type.
※OUT1 output could be set to 0 in all modes and 0 value output turns ON.
※OUT2 output could not set to 0 in C(C). R(R), P(P) or Q(Q) output mode.
J-21
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(S)
Field
network
device
(T)
Software
(U)
Other
CT Series
Output operation mode(Counter)
Output mode Up/Down - A, B, C
Operation
RESET
999999
PRESET2
PRESET1
0
-99999
OUT1
OUT2
(OUT)
S
(S)
※OUT1 and OUT2 keeps ON status in
following condition:
Counting display value ≧ PRESET1
Counting display value ≧ PRESET2
RESET
999999
PRESET2
PRESET1
0
-99999
OUT1
T
(T)
Retained output Coincidence
output
※OUT1 output is off:
Counting display value ≧ PRESET1
※OUT2 keeps ON status in following
condition:
Counting display value ≧ PRESET2
OUT2
(OUT)
RESET
※When counting display value is equal
to setting value(PRESET1, PRESET2)
only, OUT1 or OUT2 output keeps ON
status.
※When setting 1kcps for counting
speed, solid state contact output
should be used.
999999
PRESET2
PRESET1
0
D
(D)
-99999
OUT1
OUT2
(OUT)
※The single preset type output(OUT) is operated as OUT2 of dual preset type.
※The dual preset model OUT1 output is operated as one-shot or retained output.(except S, T, D mode)
※OUT1 output could be set to 0 in all modes and 0 value output turns ON.
※OUT2 output could not set to 0 in C(C), R(R), P(P) or Q(Q) output mode.
Counter operation of the indicator(CT6S-I, CT6Y-I, CT6M-I)
Indicate
mode
(DSpM)
TOTAL
(TOTAL)
HOLD
Count chart
In case of input mode is Up
(Up, Up-1, Up-2)
In case of input mode is Down
(Down, Down-1, Down-2)
RESET
RESET
999999
999999
0
-99999
RESET
999999
PRESET
999999
PRESET
0
(HOLD)
0
Operation
Count value increases or decreases
until RESET input is applied.
When reaching max. count value or
min. count value, it will be reset and
count simultaneously.
Count value increases or decreases
until RESET input is applied, count
value indicator flashes when reaching
preset value(Up count) or 0(Down
count).
0
● In case of the input mode is Command input (UD-A), Individual input(UD-B), Phase difference input(UD-C).
RESET
999999
0
-99999
J-22
※In case of UP/DOWN (UD-A, UD-B, UD-C) input mode, indication mode (DSpM) of the configuration is not displayed.
Programmable Counter/Timer
Parameter setting(Timer)
Setting mode
How to set
Counter/Timer
C-T
COUN
(
key: To select setting mode
or
key: To change setting value)
(B)
Fiber
optic
sensor
※COUN: COUNTER
TIME: TIMER
TIME
(C)
Door/Area
sensor
6digit type
SEC
99(999
SEC
999(99
0.001s to
999.999s
0.01s to
9999.99s
HOUR
9999(9
0.1h to
99999.9h
Timer range
HOUR/MIN/SEC
UP/DOWN mode
U-D
Indication mode
DSpM
Memory protection
DATA
Output mode
OUtM
SEC
9999(9
SEC
999999
M S
995(99
M S
9995(9
0.1s to
99999.9s
1s to
999999s
0.01s to
99m59.99s
0.1s to
999m59.9s
H M
999959
H M 5
995959
MIN
999999
MIN
9999(9
M 5
999959
1m to
9999h59m
1s to
99h59m59s
1m to
999999m
0.1m to
99999.9m
1s to
9999m59s
SEC
9(99
SEC
99(9
0.001s to
9.999s
0.01s to
99.99s
0.1s to
999.9s
UP
OND
SEC
9959
1s to
9999s
1s to
99m59s
HOUR
9999
H M
9959
MIN
9999
MIN
99(9
1h to
9999h
1m to
99h59m
1m to
9999s
0.1m to
999.9m
(E)
Pressure
sensor
(F)
Rotary
encoder
(G)
Connector/
Socket
HOLD
(I)
SSR/
Power
controller
(J)
Counter
(K)
Timer
ONtD
ONd2
FLK
FLk1
INTG
NFd1
NFD
OFD
FLk2
INt2
OUT1 output time
OUT1
Input logic
S1G
※NPN: No-Voltage input
※PNP: Voltage input
Input signal time
InT
1
LOc3
LOc2
(O)
Sensor
controller
INt1
key: To shift flashing digit position of OUT1 output time value.
key: To change OUT1 output time value.
※Set OUT1 one-shot output time.
※Setting range: 0.01 to 99.99sec., Hold
※HOLD is displayed by pressing key 4 times.
[unit: ms]
(N)
Display
unit
INT
OUT2 output time
OUT2
LOc1
(M)
Tacho/
Speed/ Pulse
meter
※Used for the indicator only.
※치CLR : Initializes time value when power is off.
REC : Memorizes time value at the moment of power off.
ONd1
LOFF
(L)
Panel
meter
※Used for the indicator only.
※ It is added that the feature which set the setting time when
selecting H
OLD or ONtD (Refer to J-28 page ' Timer
operation for the indicator').
REC
20
(H)
Temp.
controller
※UP: Time proceeds from 0 to the setting value.
※DN: Time proceeds from the setting value to 0.
DN
TOTAL
CLR
SEC
9999
key: To shift flashing digit position of OUT2 output time value.
key: To change OUT2 output time value.
※Set OUT2 one-shot output time.
※Setting range: 0.01 to 99.99sec.
※HOLD is displayed by pressing key 4 times.
Lock key
LOCK
(D)
Proximity
sensor
4digit type
SEC
(999
(A)
Photo
electric
sensor
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
※Check input logic value(PNP, NPN).
※CTS/CTY: Set min. external INA, INH, RESET signal width.
※CTM: Set min. external INA, RESET, INHIBIT,
BATCH RESET signal width.
(U)
Other
※LOFF: Cancellation of the lock mode
LOc1: Locks
key.
LOc2: Locks , , keys.
LOc3 : Locks , , , keys.
J-23
CT Series
One-shot output
Retained output
Output operation mode(Timer)
Output mode Input mode
Operation
Signal On Delay(Power Reset)
1) Time starts when INA signal turns on.
2) When INA signal turns off, time resets.
3) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
4) Control output operates as retained
or one-shot output.
POWER
INA(START)
INH(INHIBIT)
OND
(OND)
RESET
Setting time2
UP
Setting time1
Display
Down
One-shot output Retained output
0
INA
Setting time2
T1
Setting time1
0
OUT1
T2
OUT2
(OUT)
OUT1
T1: Setting time1
T2: Setting time2
OUT2
1) Time starts when INA signal turns on,
if INA signal is applied repeatedly,
only initial signal is recognized.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as retained
or one-shot output.
4) Only first INA input signal is valid in
case INA input signal is repeatedly
applied.
Signal On Delay 1(Power Reset)
POWER
INA(START)
INH(INHIBIT)
RESET
ONd1
(OND.1)
Setting time2
UP
Display
Down
Setting time1
0
Setting time2
INA
T1
Setting time1
OUT1
0
T2
OUT2
(OUT)
OUT1
T1: Setting time1
T2: Setting time2
OUT2
1) Time starts when power turns on.
(There is no INA function.)
2) Time resets when reset turns on.
Time starts when reset turns off.
3) Control output operates as retained
or one-shot output.
4) It memorizes display value at the
moment of power off.
Power On Delay(Power Hold)
POWER
INA(START)
INH(INHIBIT)
RESET
Setting time2
Setting time1
ONd2
UP
(OND.2)
Display
Down
HOLD
0
Setting time2
POWER
Setting time1
0
T1
OUT1
T2
OUT2
(OUT)
OUT1
OUT2
t
1) Time starts when INA signal turns on.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as retained
output, output turns off for the T.off
time and turns off for the T.off time
and turns on for the T.on time repeatedly.
Ta+Tb = T.off setting time
4) The T.on time and T.off time must be
set individually.
5) In case of using the contact output, min.
setting time must be set over 100ms.
Flicker(Power Reset)
POWER
INA(START)
INH(INHIBIT)
RESET
T.off
setting time
T.on
setting time
FLK
(FLK)
UP
Display
Down
0
T.off
setting time
POWER
T.on
setting time
0
INA
T.off
OUT2(OUT)
T1: Setting time1
T2: Setting time2
a t-a
T.on Ta
Tb T.on
T.off T.on
T.off T.on
T.off
T.off
T.on
T.off
OUT2
(OUT)
※Power Reset: There is no memory protection.(Initializes the display value when power is off)
Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized
display value when power is resupplied.)
J-24
Programmable Counter/Timer
Output operation mode(Timer)
One-shot output One-shot output Retained output
Retained output
Output mode Input mode
Operation
Flicker 1(Power Reset)
1) Time starts when INA signal turns on.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as retained
output.
4) In case of using the contact output, min.
setting time must be set over 00ms.
Hold output
POWER
INA(START)
INH(INHIBIT)
RESET
Setting time
Up
Display
Down
FLk1
(FLK.1)
INA
T
T
OUT2
(OUT)
0
1) Time starts when INA signal turns on.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as one-shot
output.
4) In case of using the contact output,
min. setting time must be set over
100ms.
POWER
INA(START)
INH(INHIBIT)
RESET
Setting time
Up
Display
Setting time
INA
0
OUT2
(OUT)
Down
t
t
t
T
T
POWER
INA(START)
INH(INHIBIT)
RESET
Setting time
Up
Display
Down
FLk2
(FLK.2)
0
INA
0
OUT2
(OUT)
POWER
INA(START)
INH(INHIBIT)
RESET
Display
Down
Setting time
0
T
T-c
Hold
c
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
T
(Q)
Stepper
motor&
Driver&Controller
T:Setting time
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
POWER
Setting time
0
t
OUT2(OUT)
(I)
SSR/
Power
controller
(P)
Switching
mode power
supply
1) Time starts when INA signal turns ON and
the display value at the moment when
power is off is memorized.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as one-shot
output.
4) In case of using the contact output, min.
setting time must be set over 100ms.
One-Shot output
(H)
Temp.
controller
(K)
Timer
POWER
Setting time
OUT2(OUT)
Up
T
1) Time starts when INA signal turns ON and
the display value at the moment when
power is off is memorized.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) Control output operates as retained output.
4) Control output will be reversed when it
reaches to setting time.(At the initial
start, OUT2 control output is OFF).
5) In case of using the contact output, min.
setting time must be set over 100ms.
Hold output
(G)
Connector/
Socket
T:Setting time
OUT2(OUT)
Flicker 2(Power Hold)
(D)
Proximity
sensor
(J)
Counter
POWER
0
(C)
Door/Area
sensor
(F)
Rotary
encoder
T
T:Setting time
OUT2(OUT)
One-Shot output
(B)
Fiber
optic
sensor
(E)
Pressure
sensor
POWER
0
Setting time
(A)
Photo
electric
sensor
t
t
a
t-a
t
INA
OUT2
(OUT)
T
T-c
Hold
c
(U)
Other
T
T:Setting time
※Power Reset: There is no memory protection.(Initializes the display value when power is off)
Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized
display value when power is resupplied.)
J-25
CT Series
Output operation mode(Timer)
Output mode Input mode
Interval (Power Reset)
POWER
INA(START)
INH(INHIBIT)
RESET
ㅑㅜINT
(INT)
Setting time
Up
0
Display
Setting time
Down
0
OUT2(OUT)
Interval 1(Power Reset)
POWER
INA(START)
INH(INHIBIT)
INt1
(INT.1)
RESET
Setting time
Up
0
Display
Setting time
Down
0
One-shot output One-shot output Retained output
Retained output
Operation
1) Control output turns ON and time starts
when INA signal turns ON.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) When it reaches setting time, indication
value and control output are reset
automatically.
4) Control output is ON when time is
progressing.
POWER
INA
POWER
INA(START)
INH(INHIBIT)
RESET
INt2
(INT.2)
Setting time1
Up
T
T:Setting time
1) Control output turns ON and time starts
when INA signal turns ON.
2) When INA signal is on:
Power ON Time Start is operated
Power OFF Time Start is operated
3) When it reaches setting time, indication
value and control output are reset
automatically.
4) Control output is ON when time is
progressing.
5) INA input is ignored while time is
progressing.
POWER
INA
OUT2
(OUT)
OUT2(OUT)
Interval 2(Power Reset)
T
OUT2
(OUT)
T
T:Setting time
1) Time starts when INA input is ON and
resets when INA input is OFF.
2) INA input is ON, OUT1 output is ON during
T1 or t1.
3) When it reaches setting time1, display
value resets and OUT2 output is ON
during T2 or t2 output time.
※ Output turns OFF when reaching the
setting time even if one-shot time
is longer than setting time.
Setting time2
0
Display
Setting time2
Down
Setting time1
0
OUT1
OUT2
INA
T1
OUT1
OUT2
T2
t1
T1: Setting time1
T2: Setting time2
t1: One-shot1
t2: One-shot2
t2
(Single preset model has no INT.2 mode)
※Power Reset: There is no memory protection.(Initializes the display value when power is off)
Power Hold: There is memory protection.(Memorizes the display value at the moment of power off, indicates the memorized
display value when power is resupplied.)
J-26
Programmable Counter/Timer
Output operation mode(Timer)
Output mode Input mode
Signal Off Delay1(Power Reset)
POWER
INA(START)
INH(INHIBIT)
RESET
OFD
(OFD)
Setting time
Up
Display
Down
0
Setting time
0
OUT2(OUT)
On-Off Delay (Power Reset)
POWER
INA(START)
INH(INHIBIT)
RESET
NFD
(NFD)
On_Delay
Off_Delay
Up
Display
Down
0
On_Delay
Off_Delay
0
One-shot output One-shot output Retained output
Retained output
Operation
1) If INA is ON, control output remains
ON. (except when power is off and
reset is on)
2) When INA signal is OFF, time processes.
3) When it reaches setting time, indication value and control output are
reset automatically.
POWER
INA
T
OUT2
(OUT)
T: Setting time
T1
OUT2
(OUT)
POWER
INA(START)
INH(INHIBIT)
RESET
NFd1
Up
(NFD.1)
Display
Up
Down
Display
Down
On_Delay
Off_Delay
0
On_Delay
Off_Delay
0
OUT2(OUT)
OUT2
(OUT)
T1
T2
POWER
INTG
(INTG)
Up
Display
Down
0
Setting time
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(L)
Panel
meter
(M)
Tacho/
Speed/ Pulse
meter
(N)
Display
unit
(O)
Sensor
controller
(P)
Switching
mode power
supply
(R)
Graphic/
Logic
panel
INA(START)
RESET
Setting time
(E)
Pressure
sensor
(Q)
Stepper
motor&
Driver&Controller
T1: On_Delay
T2: Off_Delay
Integration Time(Power Reset)
INH(INHIBIT)
(D)
Proximity
sensor
(K)
Timer
T1: On_Delay
T2: Off_Delay
1) When INA input turns ON, time
progresses and output turns ON
after On_Delay time.
2) When INA input turns OFF, time
progresses and output turns OFF
after Off_Delay time.
3) If INA input turns OFF within On_
Delay time, output will turn ON and
step2 operate.
4) If INA input turns ON within Off_
Delay time, output will turn OFF
and step1 operate.
INA
(C)
Door/Area
sensor
(J)
Counter
T2
OUT2(OUT)
On-Off Delay1 (Power Hold)
(B)
Fiber
optic
sensor
(F)
Rotary
encoder
1) When INA input is ON, output is
ON and time is progressing, then
output is OFF after On_Delay time.
2) When INA input is OFF, output is
ON and time is progressing, then
output is OFF after Off_Delay time.
3) If INA input is OFF within On_Delay
time, step 2 starts again.
4) If INA input is ON within Off_Delay
time, step 1 starts again.
INA
(A)
Photo
electric
sensor
1) Time is progressing while INA input
is ON.
2) Time progress stops while INA input is
OFF.
3) When it reaches the setting time,
output is ON.
0
OUT2(OUT)
※Power Reset: There is no memory protection.(Initializes the display value and the output status when re-supplying the power.)
Power Hold: There is memory protection.(It memorizes the status of power off. When re-supplying the power, it returns
the memorized display value and the output status.)
J-27
(S)
Field
network
device
(T)
Software
(U)
Other
CT Series
Timer operation of the indicator(CT6S-I, CT6Y-I, CT6M-I)
When memory protection setting is OFF
POWER
INA(START)
INH(INHIBIT)
Up
Display
TOTAL
(TOTAL)
Down
RESET
Max.
time range
0
Max.
time range
1) Time starts when INA input is ON.
2) Setting value is initialized when Reset input
is ON.
3) Time progress stops when INHIBIT input is
ON.
4) Resets when power is OFF.
0
When memory protection setting is ON
POWER
INA(START)
INH(INHIBIT)
Up
Display
Down
RESET
Max.
time range
0
Max.
time range
1) Time starts when INA input is ON.
2) Setting value is initialized when Reset input
is ON.
3) Time progress stops while INHIBIT input
is ON.
4) Display value at the moment of power OFF
is memorized.
0
When memory protection setting is OFF
POWER
INA(START)
INH(INHIBIT)
RESET
Up
Display
HOLD
(HOLD)
Down
Setting time
0
Setting time
0
When memory protection setting is ON
POWER
INA(START)
INH(INHIBIT)
RESET
Up
Display
Setting time
0
Setting time
Down
0
When memory protection setting is OFF
POWER
INA(START)
INH(INHIBIT)
RESET
Up
Display
ONtD
(On Time
Display)
Setting time
0
Setting time
Down
0
When memory protection setting is ON
POWER
INA(START)
INH(INHIBIT)
RESET
Setting time
Up
Display
0
Setting time
Down
0
J-28
1) Time progresses when INA input is ON.
2) Time progress stops while INA input is OFF.
3) When time reaches setting time, display
value will stop and flash.
4) When reset input is applied, display value
is initialized.
5) Resets when power is OFF.
1) Time progresses when INA input is ON.
2) Time progress stops while INA input is OFF.
3) When time reaches setting time, display
value will stop and flash.
4) When reset input is applied, display value
is initialized.
5) Display value the moment when power is
OFF is memorized.
※ON time indicate mode of INA input
1) Time reset start operates when INA input
turns ON.
2) Time progress stops while INA input is OFF.
3) When time progress stops and power is
off, the display value is initialized.
4) If progress time is greater than setting
time when INA input turns off, display
value flashes and operation stops until
reset signal is applied.
※ON time indicate mode of INA input
1) Time reset start operates when INA input
turns ON.
2) Time progress stops while INA input is OFF.
3) When time progress stops and power is
off, the display value is memorized.
4) If progress time is greater than setting
time when INA input turns off, display
value flashes and operation stops until
reset signal is applied.
Programmable Counter/Timer
Timer '0' time setting
(A)
Photo
electric
sensor
Available output operation mode to set '0' time setting
OND, ONd1, ONd2, NFD, NFd1
Operation according to output mode(at 0 time setting)
1) OND(Signal ON Delay) mode [OND]
● Setting time1 is set to 0
UP mode
DOWN mode
INA(START)
(B)
Fiber
optic
sensor
● Setting time2 is set to 0
INA(START)
0
0
(E)
Pressure
sensor
OUT1
OUT1
OUT2
OUT2
2) OND.1(Signal ON Delay 1) mode [ONd1]
● Setting time1 is set to 0
UP mode
DOWN mode
INA(START)
(F)
Rotary
encoder
● Setting time2 is set to 0
(G)
Connector/
Socket
INA(START)
RESET
Setting time1
RESET
Setting time2
(H)
Temp.
controller
0
0
OUT1
OUT1
(I)
SSR/
Power
controller
OUT2
OUT2
3) OND.2(Power ON Delay2) mode [ONd2]
● Setting time1 is set to 0
UP mode
● Setting time2 is set to 0
POWER
RESET
Setting time 1
RESET
Setting time1
0
0
OUT1
OUT1
OUT2
OUT2
4) NFD(ON-OFF Delay) mode [NFD]
● OFF_Delay setting time is set to 0
Up
OUT2
(OUT)
(O)
Sensor
controller
Off_Delay
0
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
OUT2
(OUT)
● ON_Delay setting time is set to 0
(R)
Graphic/
Logic
panel
INA(START)
RESET
RESET
Display On_Delay
0
Down
(N)
Display
unit
Display Off_Delay
0
Down
INA(START)
On_Delay
0
(M)
Tacho/
Speed/ Pulse
meter
RESET
OUT2
(OUT)
5) NFD.1(ON-OFF Delay1) mode [NFd1]
● OFF_Delay setting time is set to 0
(L)
Panel
meter
INA(START)
RESET
Display On_Delay
0
Down
(K)
Timer
● ON_Delay setting time is set to 0
INA(START)
On_Delay
0
(J)
Counter
UP mode
DOWN mode
POWER
Up
(D)
Proximity
sensor
Setting time 2
Setting time2
Up
(C)
Door/Area
sensor
Up
(S)
Field
network
device
Off_Delay
0
Display Off_Delay
0
Down
(T)
Software
OUT2
(OUT)
(U)
Other
Setting value1(PS1) is higher than Setting value2(PS2)
OND(OND), OND.1(ONd1)or OND.2(ONd2)output mode
● UP mode: When the timer setting value1 is greater than the setting value 2, OUT1 output does not turn ON.
● DOWN mode: When the timer setting value1 is greater than the setting value 2, OUT1 output does not turn ON.
If the setting value 1 is same as the setting value2 and START signal is applied, OUT1 output turns ON
immediately.
J-29
CT Series
Communication mode
Parameter setting
Setting mode
(
key: To select setting mode,
or
key: To change setting value)
How to set
※Setting range of com. address: 1 to 127
: To shift flashing digits of Com. address.
※If the same address is applied during multicom.,
: To change the flashing digits.
it will not work correctly.
Com. address
(ADDR)
Com. speed
(BPS)
24
Com. parity
(PRTY)
NONE
Com. stop bit
(STP)
1
48
96
192
EVEN
384
※2400/4800/9600/19200/38400bps
※NONE: None EVEN : Even number ODD: Odd number
ODD
2
※Setting range according to com. speed.
: To shift flashing digits position of com.
response waiting time.
: To change the flashing digits position
value.
esponse
waiting time
(RSwT)
Com. write
(COmW)
ENA
2400bps
4800bps
9600bps
19200bps
38400bps
16ms to 99ms
8ms to 99ms
5ms to 99ms
5ms to 99ms
5ms to 99ms
※ENA : Permits com. write(Enable)
DISA : Prohibits com. write(Disable)
DISA
Application of system organization
RS485
RS232C
RxD - RxD
TxD - TxD
GND - GND
GND
V(12-24VDC)
Terminating
resistance
B(-)
B(1)
A(+)
RS232C Cable
Computer
A(+) B(-)
B(-)
ON
A(+)
OFF
A(+) B(-)
CT Series
#31
A(+) B(-)
CT Series CT Series
#01
#02
CT Series
#30
A(+)
※It is recommended to use communication converter, RS485 to Serial converter(SCM-38I, sold separately), USB to
RS485 converter(SCM-US48I, sold separately). Please use a proper twist pair for RS485 communication.
Communication control ordering
A
※A → Min. 1sec. after applying power
B → 38400bps: Approx. 1ms.
19200bps: Approx. 2ms.
9600bps: Approx. 4ms.
4800bps: Approx. 8ms.
2400bps: Approx. 16ms.
C → Min. 20ms
J-30
C
Data
Data
CRC16
Command
Address code
B
CRC16
CT Series
Command
Data
CRC16
Command
Address code
Upper system
Address code
1. The communication method is Modbus RTU(PI-MBUS-300-REV.J).
2. After 1sec. of power supply into the high order system, it starts to communicate.
3. Initial communication will be started by the high order system. When a command comes out from the high order system,
CT Series will respond.
Programmable Counter/Timer
Communication command and block
(A)
Photo
electric
sensor
The format of query and response
1) Read Coil Status(Func 01 H),
Read Input Status(Func 02 H
5) Preset Multiple Registers(Func 10 H)
● Query(Master)
● Query(Master)
Starting
Slave
Address
Address Function
High
Low
1Byte 1Byte 1Byte 1Byte
No. of Points
High
1Byte
Low
1Byte
Error Check
(CRC 16)
Low
High
1Byte 1Byte
CRC 16
Data
Data
Data
1Byte
1Byte
1Byte
1Byte
Error Check
(CRC 16)
Low
High
1Byte 1Byte
CRC 16
2) Read Holding Registers(Func 03 H),
Read Input Registers(Func 04 H)
● Query(Master)
Starting
Slave
Address
Address Function
High
Low
1Byte 1Byte 1Byte 1Byte
No. of Points
High
1Byte
Low
1Byte
Error Check
(CRC 16)
Low
High
1Byte 1Byte
CRC 16
● Response(Slave)
Error Check
Data
Data
Slave Function Byte Data
(CRC 16)
Address
Count
High Low High Low High Low Low High
1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte
CRC 16
3) Force Single Coil(Func 05 H)
● Query(Master)
Coil Address
Slave
Address Function
High
Low
1Byte 1Byte 1Byte 1Byte
Force Data
High
1Byte
Low
1Byte
Error Check
(CRC 16)
Low
High
1Byte 1Byte
CRC 16
● Response(Slave)
Coil Address
Slave
Function
Address
High
Low
Force Data
High
Low
Error Check
(CRC 16)
Low
High
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
CRC 16
Register
Slave
Address
Address Function
High
Low
Preset Data
High
Low
Error Check
(CRC 16)
Low
High
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
Byte
Count
High Low High Low
Data
Error
Check
(CRC 16)
Data
High Low High Low Low High
● Response(Slave)
Slave
Function
Address
Starting Address
No. of Register
Error Check
(CRC 16)
High
Low
High
Low
Low
High
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
(G)
Connector/
Socket
CRC 16
(H)
Temp.
controller
Read Coil Status(Func 01 H)
Master reads OUT2 00002(0001H) to 00003(0002H),
OUT1 output status(ON : 1, OFF : 0) from the
Slave(Address 01).
● Query(Master)
(I)
SSR/
Power
controller
Starting Address
Slave
Function
Address
High
Low
No. of Points
Error Check
(CRC 16)
High
Low
Low
High
01 H
00 H
02 H
EC H
0B H
00 H
01 H
(J)
Counter
(K)
Timer
On slave side OUT2 00003(0002H) : OFF,
OUT1 00002(0001H) : ON
● Response(Slave)
Slave
Address
Function
01 H
01 H
(L)
Panel
meter
Error Check
(CRC 16)
Low
High
D0 H
49 H
Data
Byte Count (00003 to
00001)
01 H
02 H
(M)
Tacho/
Speed/ Pulse
meter
Read Input Register (Func 04 H)Master reads preset value
21004(03EBH) to 21005(03ECH) of counter/timer, Slave
(Address 15).
● Query(Master)
Starting Address
Slave
Function
Address
High
Low
No. of Points
High
Low
Error Check
(CRC 16)
Low
High
0F H
00 H
02 H
00 H
04 H
03 H
EB H
95 H
Error Check
(CRC 16)
Data
Data
High
Low
High
Low
Low
High
0F H
E2 H
40 H
00 H
01 H
E2 H
28 H
(T)
Software
1Byte
(U)
Other
Register
Slave
Address
Address Function
High
Low
Preset Data
High
Low
Error Check
(CRC 16)
Low
High
1Byte
1Byte
1Byte
1Byte
1Byte
1Byte
(Q)
Stepper
motor&
Driver&Controller
(S)
Field
network
device
CRC 16
● Response(Slave)
1Byte
(O)
Sensor
controller
(R)
Graphic/
Logic
panel
Slave
Byte
Function
Count
Address
04 H
(N)
Display
unit
(P)
Switching
mode power
supply
In case that the present value is 123456(0001 E240 H) in
slave side, 31004(03EBH): E240 H, 31005(03ECH): 0001H
04 H
(D)
Proximity
sensor
(F)
Rotary
encoder
6) Application
01 H
(C)
Door/Area
sensor
(E)
Pressure
sensor
● Response(Slave)
4) Preset Single Register(Func 06 H)
● Query(Master)
1Byte
No. of
Register
CRC 16
Byte
Slave
Address Function Count
1Byte
Starting
Slave
Address
Function
Address
1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte 1Byte
● Response(Slave)
1Byte
(B)
Fiber
optic
sensor
1Byte
CRC 16
J-31
CT Series
Modbus Mapping Table
1) Reset/Output
No(Address)
00001(0000)
00002(0001)
00003(0002)
Func
01/05
01
01
00004(0003) 01
4) Monitoring data
Explanation
Reset
OUT2 output
OUT1 output
Setting range Notice
0:OFF 1:ON
0:OFF 1:ON
0:OFF 1:ON
For BATCH
BATCH output 0:OFF 1:ON
output model
For BATCH
00005(0004) 01/05 BATCH resets 0:OFF 1:ON
output model
2) Terminal input status
No(Address) Func Explanation
10001(0000) 02
10002(0001) 02
10003(0002) 02
10004(0003) 02
10005(0004) 02
Setting range Notice
Terminal input
INA input status
0:OFF 1:ON
status
Terminal input
INB input status
0:OFF 1:ON
status
Terminal input
INHIBIT input status 0:OFF 1:ON
status
Terminal input
RESET input status 0:OFF 1:ON
status
BATCH RESET
Terminal input
0:OFF 1:ON
input status
status
3) Product Information
No(Address)
30001~30100
30101(0064)
30102(0065)
30103(0066)
30104(0067)
30105(0068)
30106(0069)
30107(006A)
30108(006B)
30109(006C)
30110(006D)
30111(006E)
30112(006F)
30113(0070)
30114(0071)
30115(0072)
30116(0073)
30117(0074)
Func
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
04
30120(0077) 04
Explanation
Reserved
Product number H
Product number L
Hardware version
Software version
Model no. 1
Model no. 2
Model no. 3
Model no. 4
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Coil Status
Start Address
Coil Status
Quantity
Input Status
Start Address
30121(0078) 04
30122(0079) 04
30118(0075) 04
Notice
Model ID
"CT"
"6M"
"-2"
"PT"
0000
No(Address) Func Explanation
BA.O LED
display status
OUT2 LED
display status
OUT1 LED
display status
BA.S LED
display status
31001
LOCK LED
04 display status
(03E8)
PS2 LED
display status
PS1 LED
display status
TMR LED
display status
CNT LED
display status
Present value
31002(03E9)
04 of BATCH
31003(03EA)
counter
31004(03EB)
31005(03EC)
04
31006(03ED) 04
31007(03EE)
31008(03EF)
04
31009(03F0)
31010(03F1)
31011(03F2)
31012(03F3)
04
04
31013(03F4) 04
Setting range
Notice
0:OFF 1:ON
Bit 5
0:OFF 1:ON
Bit 6
0:OFF 1:ON
Bit 7
0:OFF 1:ON
Bit 10
0:OFF 1:ON
Bit 11
0:OFF 1:ON
Bit 12
0:OFF 1:ON
Bit 13
0:OFF 1:ON
Bit 14
0:OFF 1:ON
Bit 15
0 to 999999
For BATCH
output
model
Counter
-99999 to
Present value 6digit type: 999999
Use counter
of
and timer
4digit
type:
-999
to
9999
counter/timer Timer: Within time setting in common
range
Counter:
Counter: decimal point 40058 Data
of display value Timer:
Timer: Time range
40102 Data
Counter
6digit type: -99999 to
Use counter
PS(2)
999999
timer
setting value 4digit type: -999 to 9999 and
Timer: Within time setting in common
range
Counter
6digit type: -99999 to
Use counter
PS1
999999
timer
setting value 4digit type: -999 to 9999 and
Timer: Within time setting in common
range
Setting value
Use counter
of BATCH
0 to 999999
and timer
counter
in common
Checking the 0: NPN, 1 : PNP
input logic
Display unit
-
● Date format of 31001(03E8) address bit
0000
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit4 Bit 3 Bit 2 Bit 1 Bit 0
Input Status Quantity
-
CNT TMR PS1 PS2 LOCK BA.S -
-
OUT1 OUT2 BA.O -
-
-
-
-
0 or 1 0 or 1 0 or 1 0 or 1 0 or 1 0 or 1 0
0
0 or 1 0 or 1 0 or 1 0
0
0
0
0
0000
-
30124(007B) 04
Holding Register
Start Address
Holding Register
Quantity
Input Register
Start Address
30125(007C) 04
Input Register Quantity
-
30119(0076) 04
30123(007A) 04
J-32
0064
※2 Words data format: Upper data has high number address.
Ex)31004 : Present Value(Low Word),
31005 : Present Value(High Word)
5) Preset value setting group
No(Address) Func
40001(0000) 03
06
40002(0001) 16
40003(0002) 03
06
40004(0002) 16
40005(0004) 03
06
40006(0005) 16
Explanation
Setting range
Counter
PS2 setting value
PS setting value 6digit type: 0 to
999999
4digit type: 0 to 9999
PS1 setting
Timer: Within time
value
setting range
BATCH counter
0 to 999999
setting value
Notice
Use counter
and timer
in common
Use counter
and timer
in common
Use counter
and timer
in common
Programmable Counter/Timer
6) Function setting mode (Counter group)
No(Address)
40051(0032)
40052(0033)
Func
03/06/16
03/06/16
40053(0034)
03/06/16
40054(0035)
03/06/16
40055(0036)
03/06/16
40056(0037)
40057(0038)
03/06/16
03/06/16
40058(0039)
03/06/16
40059(003A)
03/06/16
40060(003B)
03/06/16
40061(003C)
40062(003D)
40063(003E)
40064(003F)
40065(0040)
40066(0041)
03/06/16
03/06/16
03/06/16
03/06/16
Explanation
Counter/Timer(C-T)
Setting range
1: COUN 1: TIME
Input mode(IN)
0: UP
1: UP-1
2: UP-2
3: DN
4: DN-1
(A)
Photo
electric
sensor
Notice
Use counter and timer in common
5: DN-2
6: UD-A
7: UD-B
8: UD-C
(B)
Fiber
optic
sensor
-
(C)
Door/Area
sensor
Indication mode(DISM) 0: TOTAL
1: HOLD
0: F
3: R
6: Q
9: T
Output mode(OUTM)
1: N
4: K
7: A
10: D
5: P
8: S
2: C
Maximum counting
0: 1
2: 1K
4: 10K
1: 30
3: 5K
speed(CPS)
OUT2(OUT) output time 0001~ 9999
0001~ 9999
OUT1 Output time
0: ------ 2: ----.-- 4: --.---Decimal point(DP)
1: -----.- 3: ---.--- 5: -.----0: 1
Min. reset time(RST)
1: 20
Prescale decimal
0: -----.- 3: ---.--- 5: -.----2: ----.-- 4: --.---point position(SClD)
6digit type: )00001 to 999999
Prescale value(SCL)
4digit type: )001 to 9999
6digit type: 000000to 999999
Start value(STRT)
4digit type: 0000to 9999
Memory protection(DATA) 0: CLR
1: REC
Lock key(LOCK)
0: lOFF 1: LOc1 2: LOc2 3: LOc3
For the indicator
(D)
Proximity
sensor
-
(E)
Pressure
sensor
unit: ×10㎳
unit: ×10㎳
4digit type 0: ---1: ---.- 2: --.-- 3: -.--unit: ms
4digit type
1: ---.- 2: --.-- 3: -.--Connected with prescale
decimal point position
Connected with decimal
point position of display value
Use counter and timer
in common
(F)
Rotary
encoder
(G)
Connector/
Socket
(H)
Temp.
controller
(I)
SSR/
Power
controller
(J)
Counter
7) Function setting mode (Timer group)
No(Address)
Func
Explanation
40101(0064) 03/06/16 Counter/Timer(C-T)
Setting range
Notice
0: COUN 1: TIME
Use counter and timer
in common
(K)
Timer
4digit type
40102(0065)
03/06/16
Time range
(HOUR/MIN/SEC)
0: 0.001s to 9.999s
1: 0.01s to 99.99s
2: 0.1s to 999.9s
3: 1s to 9999s
4: 1s to 99m59s
0: 0.001s to 999.999s
1: 0.01s to 9999.99s
2: 0.1s to 99999.9s
3: 1s to 999999s
4: 0.01s to 99m59.99s
5: 0.1s to 999m59.9s
03/06/16
UP/Down mode
(U-D)
0: UP
40104(0067)
03/06/16
Output mode
(OUTM)
0: OND
1: ONd1
2: ONd2
40105(0068)
03/06/16
40106(0069)
03/06/16
40107(006A)
40108(006B)
40109(006C)
40110(006D)
03/06/16
03/06/16
03/06/16
03/06/16
OUT2(OUT) Output time
(OUT2)
OUT1 Output time
(OUT1)
Input signal time(INT)
Memory protection(DATA)
Lock key(LOCK)
ndication mode(DSpM)
(M)
Tacho/
Speed/ Pulse
meter
-
6digit type
40103(0066)
(L)
Panel
meter
5: 0.1m to 999.9m
6: 1m to 9999m
7: 1m to 99h59m
8: 1h to 9999h
(O)
Sensor
controller
7: INt1
8: INt2
9: OFD
10: NFD
11: NFd1
12: INtG
unit: ×10ms
0000 to 9999(0 : Hold)
unit: ×10,ms
0:
0:
0:
0:
unit: ms
Use counter and timer in common
Use counter and timer in common
For the indicator
1: 20
1: REC
1: LOc1
1: HOLD
2: LOc2
2: ONtD
3: LOc3
(Q)
Stepper
motor&
Driver&Controller
-
0000 to 9999(0: Hold)
1
CLR
lOFF
TOTAL
(P)
Switching
mode power
supply
-
1: DN
3: FLK
4: FLk1
5: FLk2
(N)
Display
unit
6: 1s to 9999m59s
7: 1m to 99999.9m
8: 1m to 999999m
9: 1s to 99h59m59s
10: 1m to 9999h59m
11: 0.1h to 99999.9h
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
J-33
CT Series
8) Function setting mode (Communication group)
No(Address)
Func
Explanation
Setting range
Notice
40151(0096)
40152(0097)
40153(0098)
40154(0099)
40155(009A)
40156(009B)
03/06/16
03/06/16
03/06/16
03/06/16
03/06/16
03/06/16
Com. address (ADDR)
Com. speed (BPS)
Com. parity (PRTY)
Stop bit (STP)
Response waiting time (RSwT)
Com. writing (COmW)
1 to 127
0: 24 1: 48 2: 96 3: 192 4: 384
0: NONE 1: EVEN 2: ODD
0: 1 1: 2
05 to 99
0: ENA 1: DISA
unit: ×100bps
unit: ms
-
Exception processing
When communication error occurs, the highest bit of received function is set
to 1, then sends response command and transmits exception code.
Slave Address
Function+80H
Exception Code
1Byte
1Byte
1Byte
Error Check(CRC16)
Low
1Byte
High
1Byte
● Illeegal Function(Exception Code: 01H): Not supporting command
● Illegal Data Address(Exception Code: 02H): Mismatch between the number of asked data and the number of transmittable data.
● Illegal Data Value(Exception Code: 03H): Mismatch between asked the number of data and transmittable the number of
data in device
● Slave Device Failure(Exception Code: 04H): Command is processed incorrectly.
Example)
Master reads output status (ON:1, OFF:0) of non existing coil 01001 (03E8 H) from Slave (Address17).
● Query(Master)
Slave Address
Function
11H
01H
Starting Address
High
03H
No. of Points
Low
E8H
Error Check(CRC16)
High
00H
Low
01H
Low
##H
High
##H
● Response(Slave)
Slave Address
Function + 80H
Exception Code
11H
81H
02H
Error Check(CRC16)
Low
High
##H
##H
Read and write of parameter value using communication
Read of the parameter area
00002(OUT2), 00003(OUT1), 00004(BA, 0), 10001 to 10005(Terminal input), 30101 to 30125(Product information),
31001 to 31013(Monitoring data)
Read and write of the parameter area
00001(Reset starts), 00005(BATCH Reset starts), 40001 to 40006(Setting value saving group),
40051 to 40066(Counter setting group), 40101 to 40110(Timer setting group),
40151 to 40156(Communication setting group)
Read of communication
Read parameter value using communication.(Function : 01H, 02H, 03H, 04H)
It is able to read communication regardless of permitting/prohibiting communication writing.
Communication write
Change parameter value using communication.(Function: 05H, 06H, 10H)
● When change the parameter setting value of ' Function setting mode Counter group' or ' Function setting mode
Timer group' using communication, reset indication will flash in 3 sec. and display value will be reset.(Counting display
value and progress time before changing parameter setting value are not saved.)
● When change the parameter setting value of ' Preset value setting group' or ' Function setting mode Communication group' using communication, counting display value or progress time will not be reset.
= 1:
), a write command does not process.
● In prohibit writing communication setting (
● If set value beyond the setting range, this setting value is substituted for the value within the setting range and then
memorized.
J-34
Programmable Counter/Timer
Proper usage
(A)
Photo
electric
sensor
The power ON/OFF
Power
ON
OFF
100㎳
The unstable time
against the input signal.
(B)
Fiber
optic
sensor
500㎳
(C)
Door/Area
sensor
Power voltage rises for 100ms after power on and falls for
500ms after power off. Therefore be sure to apply input
signal after 100ms and power turns on again after 500ms
when power turns off.
● Be sure to use insulated and resistive voltage /current or
Class2 supply power device to input 24VAC/24-48VDC
power supply model.
(D)
Proximity
sensor
(E)
Pressure
sensor
(F)
Rotary
encoder
Input signal line
● Use as short a cable from the sensor to this unit as possible.
● Use shielded cable for long input line.
● Wire as separating input line from the power line.
(G)
Connector/
Socket
(H)
Temp.
controller
When selecting input logic
(I)
SSR/
Power
controller
Be sure that supply power is off when selecting input logic,
then select logic input according to input logic changing
method.
(J)
Counter
Contact count input (When it is used as Counter)
If apply contact input at high speed mode(1k, 5k, 10k), it
may cause miscount by chattering.
Therefore set low speed mode(1cps or 30cps) at contact input.
(K)
Timer
(L)
Panel
meter
When test dielectric voltage and insulation resistance of the control panel with this
unit installed.
(M)
Tacho/
Speed/ Pulse
meter
● Please isolate this unit from the circuit of control panel.
● Please make all terminals of this unit short-circuited.
(N)
Display
unit
Do not use below places.
(O)
Sensor
controller
● Place where there are severe vibration or impact.
● Place where strong alkalis or acids are used.
● Place where there are direct ray of the sun.
● Place where strong magnetic field or electric noise are
generated.
(P)
Switching
mode power
supply
(Q)
Stepper
motor&
Driver&Controller
Installation environment
● It shall be used indoor.
● Altitude Max. 2000m
● Pollution Degree 2
● Installation Category II
(R)
Graphic/
Logic
panel
(S)
Field
network
device
(T)
Software
(U)
Other
J-35
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement