20G501-00 E2 User Manual
Embedded Solutions
20G501-00 E2 – 2011-06-20
G501 – 3U CompactPCI Serial®
SATA HDD/SSD Shuttle
User Manual
®
G501 – 3U CompactPCI® Serial SATA HDD/SSD Shuttle
G501 – 3U CompactPCI® Serial SATA HDD/SSD Shuttle
The G501 is a CompactPCI® Serial hard disk drive carrier board. It is designed to
carry a 2.5" SATA hard disk drive (RAID level depending on the CPU) or a solid
state drive.
The unit's front panel features four LEDs for the board's SGPIO status (used for the
hot plug functionality) and the status of the internal controller's power supply.
Block Diagram
LEDs
Controller
SGPIO
+3.3V
P1
Hard
Drive
+5V
Power
Supply
+12V
SATA
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
2
Technical Data
Technical Data
Mass Storage
• Serial ATA (SATA)
- One port for onboard 2.5" hard disk drive or solid state drive
- Transfer rates depending on HDD/SSD
- RAID level depends on CPU board
External Interfaces
• 4 LEDs at front panel
- 3 for the SGPIO status (for hot plug functionality)
- 1 for the internal controller's supply voltage status
CompactPCI Serial
• Compliance with CompactPCI Serial PICMG CPCI-S.0 Specification
• Peripheral slot
• Host interface: one SATA and one SGPIO interface
Electrical Specifications
• Supply voltage
- +12V (-25%/+10%), power consumption depending on HDD/SSD
Mechanical Specifications
• Dimensions: conforming to CPCI-S.0 specification for 3U boards
• Hot plug functionality (depending on CPU board).
• Weight: 125 g (without HDD/SSD)
Environmental Specifications
• Temperature range (operation):
- -40..+85°C (depending on HDD or SSD; please refer to the HDD/SSD specifications for possible limits)
- Airflow: min. 1.5 m/s
• Temperature range (storage): -40..+85°C
• Relative humidity (operation): max. 95% non-condensing
• Relative humidity (storage): max. 95% non-condensing
• Altitude: -300 m to + 3,000 m
• Shock: 15 g/11 ms
• Bump: 10 g/16 ms
• Vibration (sinusoidal): 2 g/10..150 Hz
MTBF
• 2.032.578 h @ 40°C according to IEC/TR 62380 (RDF 2000)
Safety
• PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
3
Product Safety
Product Safety
!
Electrostatic Discharge (ESD)
Computer boards and components contain electrostatic sensitive devices.
Electrostatic discharge (ESD) can damage components. To protect the board and
other components against damage from static electricity, you should follow some
precautions whenever you work on your computer.
• Power down and unplug your computer system when working on the inside.
• Hold components by the edges and try not to touch the IC chips, leads, or circuitry.
• Use a grounded wrist strap before handling computer components.
• Place components on a grounded antistatic pad or on the bag that came with the
component whenever the components are separated from the system.
• Store the board only in its original ESD-protected packaging. Retain the original
packaging in case you need to return the board to MEN for repair.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
4
About this Document
About this Document
This user manual describes the hardware functions of the board, connection of
peripheral devices and integration into a system. It also provides additional
information for special applications and configurations of the board.
The manual does not include detailed information on individual components (data
sheets etc.). A list of literature is given in the appendix.
History
Issue
Comments
Date
E1
First issue
2010-03-22
E2
Updated structure of "technical data" section,
added "CompactPCI Serial" block and MTBF, hot
plug functionality now a standard feature, slight
changes to technical data (supply voltage range,
airflow)
2011-06-20
Conventions
!
italics
bold
monospace
hyperlink
This sign marks important notes or warnings concerning proper functionality of the
product described in this document. You should read them in any case.
Folder, file and function names are printed in italics.
Bold type is used for emphasis.
A monospaced font type is used for hexadecimal numbers, listings, C function
descriptions or wherever appropriate. Hexadecimal numbers are preceded by "0x".
Hyperlinks are printed in blue color.
The globe will show you where hyperlinks lead directly to the Internet, so you can
look for the latest information online.
IRQ#
/IRQ
Signal names followed by "#" or preceded by a slash ("/") indicate that this signal is
either active low or that it becomes active at a falling edge.
in/out
Signal directions in signal mnemonics tables generally refer to the corresponding
board or component, "in" meaning "to the board or component", "out" meaning
"coming from it".
Vertical lines on the outer margin signal technical changes to the previous issue of
the document.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
5
About this Document
Legal Information
MEN Mikro Elektronik reserves the right to make changes without further notice to any products herein. MEN makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does MEN assume
any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
"Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be
validated for each customer application by customer's technical experts.
MEN does not convey any license under its patent rights nor the rights of others.
Unless agreed otherwise, MEN products are not designed, intended, or authorized for use as components in systems intended
for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the MEN product could create a situation where personal injury or death may occur. Should Buyer purchase or
use MEN products for any such unintended or unauthorized application, Buyer shall indemnify and hold MEN and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that MEN was negligent regarding the design or manufacture of the part.
Unless agreed otherwise, the products of MEN Mikro Elektronik are not suited for use in nuclear reactors or for application in
medical appliances used for therapeutical purposes. Application of MEN products in such plants is only possible after the user
has precisely specified the operation environment and after MEN Mikro Elektronik has consequently adapted and released the
product.
ESM™, ESMini™, MDIS™, MDIS4™, MENMON™, M-Module™, M-Modules™, SA-Adapter™, SA-Adapters™,
UBox™, USM™ and the MBIOS logo are trademarks of MEN Mikro Elektronik GmbH. PC-MIP® is a registered trademark
of MEN Micro, Inc. and SBS Technologies, Inc. MEN Mikro Elektronik®, ESMexpress®, MIPIOS® and the MEN logo are
registered trademarks of MEN Mikro Elektronik GmbH.
PCI Express® and PCIe® are registered trademarks of PCI-SIG.
All other products or services mentioned in this publication are identified by the trademarks, service marks, or product names
as designated by the companies who market those products. The trademarks and registered trademarks are held by the
companies producing them. Inquiries concerning such trademarks should be made directly to those companies. All other brand
or product names are trademarks or registered trademarks of their respective holders.
Information in this document has been carefully checked and is believed to be accurate as of the date of publication; however,
no responsibility is assumed for inaccuracies. MEN Mikro Elektronik accepts no liability for consequential or incidental
damages arising from the use of its products and reserves the right to make changes on the products herein without notice to
improve reliability, function or design. MEN Mikro Elektronik does not assume any liability arising out of the application or
use of the products described in this document.
Copyright © 2011 MEN Mikro Elektronik GmbH. All rights reserved.
Please recycle
Germany
MEN Mikro Elektronik GmbH
Neuwieder Straße 5-7
90411 Nuremberg
Phone +49-911-99 33 5-0
Fax +49-911-99 33 5-901
E-mail [email protected]
www.men.de
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
France
MEN Mikro Elektronik SA
18, rue René Cassin
ZA de la Châtelaine
74240 Gaillard
Phone +33 (0) 450-955-312
Fax +33 (0) 450-955-211
E-mail [email protected]
www.men-france.fr
USA
MEN Micro, Inc.
24 North Main Street
Ambler, PA 19002
Phone (215) 542-9575
Fax (215) 542-9577
E-mail [email protected]
www.menmicro.com
6
Contents
Contents
1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1 Map of the Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Integrating the Board into a System . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Serial ATA (SATA) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.1
Installing a Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1.2
Removing a Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 CompactPCI Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Front-Panel Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Literature and Web Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 Finding out the Board’s Article Number, Revision and Serial Number13
Figures
Figure 1. Map of the board – front panel and top view . . . . . . . . . . . . . . . . . . . . . 8
Figure 2. Labels giving the board’s article number, revision and serial number. 13
Tables
Table 1.
Table 2.
Table 3.
Signal mnemonics of SATA connector . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pin assignment of SATA connector . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Front-panel status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MEN Mikro Elektronik GmbH
7
20G501-00 E2 – 2011-06-20
Getting Started
1
Getting Started
This chapter gives an overview of the board and some hints for first installation in a
system.
1.1
Map of the Board
Figure 1. Map of the board – front panel and top view
CompactPCI ®
Plus
SATA
2.5" hard disk or
solid state drive
SATA connector
1 2 3 4
P1
G501
1.2
Integrating the Board into a System
You can use the following check list when installing the board in a system for the
first time and with minimum configuration.
 Power-down the system.
 Insert the G501 into a CompactPCI Serial peripheral slot of your CompactPCI
Serial or hybrid system, making sure that the CompactPCI Serial connector is
properly aligned.
Note: The peripheral slots of every CompactPCI Serial system are marked by a
circle on the backplane and/or at the front panel.
 Power-up the system.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
8
Functional Description
2
Functional Description
2.1
Serial ATA (SATA) Interface
The G501 is a hard disk/solid state drive shuttle and features one serial ATA (SATA)
interface controlled by the system’s CPU board. You can connect a 2.5" hard-disk or
solid state drive.
The SATA interfaces support transfer rates up to 300 MB/s.
Table 1. Signal mnemonics of SATA connector
Signal
Direction
Function
+12V
out
+12V power supply
+3.3V
out
+3.3V power supply (optional)
+5V
out
+5V power supply
GND
-
Digital ground
SATA_RX+,
SATA_RX-
in
Differential pair of SATA receive lines
SATA_TX+,
SATA_TX-
out
Differential pair of SATA transmit lines
Connector type:
• 7- & 15-pin SATA receptacle connector, 1.27mm pitch
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
9
Functional Description
Table 2. Pin assignment of SATA connector
S1
P1
2.1.1
S1
GND
S2
SATA_TX+
S3
SATA_TX-
S4
GND
S5
SATA_RX-
S6
SATA_RX+
S7
GND
Key and spacing,
separate signal and
power segments
P1
+3.3V (optional)
P2
+3.3V (optional)
P3
+3.3V (optional)
P4
GND
P5
GND
P6
GND
P7
+5V
P8
+5V
P9
+5V
P10
GND
P11
GND
P12
GND
P13
+12V
P14
+12V
P15
+12V
Installing a Hard Disk
MEN offers a 2.5" hard-disk drive for onboard installation. With a hard disk
installed, the board still needs only one slot in the system.
See also Figure 1, Map of the board – front panel and top view, on page 8.
Please see MEN’s website for ordering options.
Perform the following steps to install a hard disk:
 Power down your system.
 Remove the G501 from the system.
 If another hard disk is already installed, follow the instructions given in Chapter
2.1.2 Removing a Hard Disk.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
10
Functional Description
 Place the hard disk on the G501 as shown below with the connector at the rear
of the hard disk aligned with the SATA connector on the G501.
 Firmly plug the hard disk into the SATA connector on the G501.
 Fasten the hard disk to the board from the other side using the four screws supplied with the G501. Apply thread locker to ensure the screws are not loosened
by vibrations.
2.1.2
Removing a Hard Disk
To remove a hard disk from the G501 simply remove the four screws holding the
hard disk in place (as shown directly above) and then unplug the hard disk from the
G501’s SATA connector.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
11
Functional Description
2.2
CompactPCI Serial Interface
The G501 supports the standard CompactPCI Serial interface (PICMG CPCI-S.0).
For full CompactPCI Serial SATA connection only the P1 connector is needed,
therefore the board only has a P1 connector to the bus.
Connector type of P1:
• 72-pin Airmax VS 4 pair, right angle header, 6 IMLA with end walls
The pin assignment of the P1 connector as defined in the CompactPCI Serial
(PICMG CPCI-S.0) specification will not be repeated here.
2.3
Front-Panel Status LEDs
The G501 has four status LEDs at its front panel.
Table 3. Front-panel status LEDs
LED
Description
1 Hot-plug / Error*
2 Locate*
3 Activity*
4 Power supply status (ON = no undervoltage)
* The functionality of LEDs 1 through 3 is dependent on the CPU board.
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
12
Appendix
3
Appendix
3.1
Literature and Web Resources
• G501 data sheet with up-to-date information and documentation:
www.men.de/products/02G501-.html
3.2
Finding out the Board’s Article Number, Revision and
Serial Number
MEN user documentation may describe several different models and/or hardware
revisions of the G501. You can find information on the article number, the board
revision and the serial number on two labels attached to the board.
• Article number: Gives the board’s family and model. This is also MEN’s ordering number. To be complete it must have 9 characters.
• Revision number: Gives the hardware revision of the board.
• Serial number: Unique identification assigned during production.
If you need support, you should communicate these numbers to MEN.
Figure 2. Labels giving the board’s article number, revision and serial number
Complete article number
02G501-00
00.00.00
Revision number
Serial number
MEN Mikro Elektronik GmbH
20G501-00 E2 – 2011-06-20
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement