Eizo RadiForce MX191 User`s manual

Eizo RadiForce MX191 User`s manual
Important
Please read PRECAUTIONS, this User’s Manual and Setup Manual
(separate volume) carefully to familiarize yourself with safe and effective
usage.
• Please read the Setup Manual (separate volume)
• The latest User’s Manual is available for download from our site:
http://www.radiforce.com
Product specification may vary with sales areas.
Confirm the specification in the manual written in language of the region of purchase.
• It shall be assured that the final system is in compliance to IEC60601-1-1 requirement.
• Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in malfunction of the
monitor.
Install the equipment in a controlled environment, where such effects are avoided.
• This is a monitor intended for use in a medical image system. It does not support the display of mammography
images for diagnosis.
Copyright© 2009 EIZO NANAO CORPORATION All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential unless prior
arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information. Although every effort has been
made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are subject to change
without notice.
VGA is a registered trademark of International Business Machines Corporation.
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
VESA is a registered trademark or a trademark of Video Electronics Standards Association in the United States and other countries.
PC-9801 and PC-9821 are trademarks of NEC Corporation.
EIZO, RadiCS, RadiForce and ScreenManager are registered trademarks of EIZO NANAO CORPORATION in Japan and other
countries.
All other trademarks are the properties of their respective owners.
Notice for this monitor
This product is suited to clinical review. It does not support the display of mammography images for diagnosis.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used
outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable for power cords and signal cables specified by us.
Use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or timer to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. (Refer to
“Cleaning” on the next page.)
The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due
to the characteristics of the panel itself, and not the product.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD
panel. (If the pressure marks remain on the LCD panel, leave the monitor with a white or black screen. The symptom
may disappear.)
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause some damages to the monitor.
Cleaning
Attention
• Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, disinfectant, and abrasive cleaner, which may damage
the cabinet or LCD panel.
NOTE
• Optional ScreenCleaner is recommended for cleaning the panel surface.
LCD Panel
• Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper.
• Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a
dry cloth for better finishing.
Cabinet
• Clean the cabinet with a soft cloth dampened with a little mild detergent.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the
environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
CONTENTS
. ............................................................ 1
2-7 Locking Buttons
[Key Lock] [Menu Lock]................................ 21
Notice for this monitor........................................... 3
2-8 Displaying Monitor Infomation [Info1] [Info2]................................................... 21
COVER
Cleaning.................................................................. 4
To use the monitor comfortably............................ 4
CONTENTS.............................................................. 5
Chapter 1 Features and Overview...................... 6
1-1 Features............................................................. 6
1-2 Buttons and Indicators..................................... 7
2-9 Setting Power Indicator ON/OFF [Power LED].................................................... 22
2-10 Setting Language [Language]....................... 22
2-11 Displaying EIZO logo...................................... 22
2-12 Resuming the Default Setting [Reset].......... 23
● To reset color adjustment values....................... 23
● To reset all adjustments to
the factory default settings............................... 23
1-3 Basic operation of Adjustment menu and the
icon list.............................................................. 8
Chapter 2 Settings and Adjustments............... 11
2-1 Utility Disk........................................................11
● Disk contents and software overview.................11
● To use RadiCS LE or ScreenManager Pro for
Medical...............................................................11
Chapter 3 Connecting Cables........................... 24
3-1 Connecting Two PCs to the Monitor............. 24
● To switch the input signal.................................. 24
● Setting auto-selection of the input signal
[Input Signal]..................................................... 25
Chapter 4 Troubleshooting................................ 26
2-2 Screen Adjustment......................................... 12
Digital Input........................................................... 12
Chapter 5 Reference.......................................... 28
Analog Input......................................................... 12
5-1 Attaching an Arm............................................ 28
2-3 Color Adjustment............................................ 15
● To select the display mode (CAL Switch mode)15
● To perform advanced adjustments.................... 16
● Adjustment items in each mode........................ 16
● To adjust the brightness [Brightness]................ 16
● To adjust the contrast [Contrast]........................ 17
● To adjust the gamma value [Gamma]................ 17
5-2 Power Saving Mode........................................ 29
5-3 Specifications................................................. 30
5-4 Glossary.......................................................... 34
5-5 Preset Timing.................................................. 36
● To adjust the color temperature [Temperature].. 18
● To adjust the gain value [Gain].......................... 18
FCC Declaration of Conformity........................... 37
● To adjust the color saturation [Saturation]......... 18
● To adjust the hue [Hue]..................................... 19
EMC Information................................................... 38
2-4 Adjusting Sharpness [Sharpness]................ 20
2-5 Setting Enable/Disable for the automatic
brightness adjustment function [Auto EcoView]............................................... 20
2-6 Turning off the monitor automatically [Off Timer]....................................................... 20
CONTENTS
Chapter 1 Features and Overview
Thank you very much for choosing an EIZO color LCD monitor.
1-1 Features
• Over drive circuit for clear motion pictures
• Dual-input system (DVI-D, D-sub)
3-1 “Connecting Two PCs to the Monitor” (page 24)
• Auto EcoView
2-5 “Setting Enable/Disable for the automatic brightness adjustment function”
(page 20)
• Sharpness
2-4 “Adjusting Sharpness” (page 20)
• Auto adjust
2-2 “Screen Adjustment” (page 12)
• 11 bit gamma correction
“To adjust the gamma value” (page 17)
• DICOM mode (CAL Switch function)
To select the display mode (CAL Switch mode) (page 15)
• CAL Switch function for selecting an optimal calibration mode
• The quality control software "RadiCS LE" (for Windows) used to calibrate
the monitor is included
Refer to the EIZO LCD Utility Disk
• Adjustment menu to execute the target function by simple operation.
1-3 “Basic operation of Adjustment menu and the icon list” (page 8)
• The utility software "ScreenManager Pro for Medical" (for Windows) to
control the monitor from a PC with mouse/keyboard is included
Refer to the EIZO LCD Utility Disk
• HDCP (High-bandwidth Digital Content Protection)
Chapter 1 Overview and Features
NOTE
• The stand of the unit can be replaced
with an arm (or another stand). (Refer
to “5-1 Attaching an Arm” on page
28.)
1-2 Buttons and Indicators
Adjustment menu
Button
1
2
3
4
5
6
7
8
1. Sensor (Auto EcoView)
2.
button
button
3.
buttons
4.
button
5.
button
6.
button
7.
8. Power indicator
Indicator status
Blue
Orange
Off
Operation status
The screen is displayed (Power on)
Power saving (Power on)
Power off
NOTE
• While the screen is displayed, the
power indicator that is lighting blue
can be turned off (see “Setting Power
Indicator ON/OFF” on page 22).
Chapter 1 Overview and Features
1-3 Basic operation of Adjustment menu and the icon list
Basic operation of Adjustment menu
Displaying the adjustment menu
Pressing the function button to change the setting or pressing
allows you to display the adjustment menu.
When pressing the input signal selection, mode or brightness control
When pressing the menu button
Modifying the setting
The operation methods differ depending on the icons.
Example
Operation method
As for the icons displayed with the +/- marks, selecting + allows you to increase the setting value
or selecting - to decrease it.
Selecting the icon displayed with
/
mark allows you to show the next menu.
The Enable/Disable setting is toggled by selecting the icon. X is displayed when the function is
invalid.
Displaying the function name
(1) Press
while the adjustment menu appears.
(2) The function name appears.
Storing the setting/Exiting the adjustment menu
After completing the setting, selecting
allows you to store the setting. Selecting
repeatedly allows you to close the
adjustment menu.
NOTE
• The adjustment menu automatically finishes when no input operation occurs in 45 seconds.
Chapter 1 Overview and Features
Adjustment menu icon list
Icon
Function
—
Overview
Determines the setting. Selecting
the icon repeatedly allows you to
close the adjustment menu.
Icon
Function
Adjusts the hue. If you set the hue
to a high value, the image turns
greenish. If low, the image turns
purplish.
Adjustable range: -100 to 100
Hue
Analog
AutoSize
Flickering, screen position,
and screen size are adjusted
automatically.
Returns to the pre-adjusted
status.
Determines the adjustment.
Every color gradation (0 to 255) can
be displayed by adjusting the signal
output level.
AutoRange
Returns to the pre-adjusted
status.
Overview
Saturation
Adjusts the color saturation.
Adjustable range: -100 to 100
Adjusts the color temperature. The
gain preset values are set for each
color temperature setting value.
Temperature Adjustable range: Native,
6500K-15000K (specified by every
500K unit, including 9300K), User (at
gain adjustment)
Gamma
Determines the adjustment.
Adjusts the gamma value.
Adjustable range: 1.8, 2.0, 2.2
Tool
Performs advanced adjustment
when the automatic adjustment fails.
The adjustments for clock, phase
and position proceed in this order.
Info1
Displays the input signal status
(analog/digital), resolution, H/V
frequency.
Clock
Eliminates vertical bars.
Info2
Displays the model name, usage
time and serial number.
Phase
Removes flickering or blurring.
Manual
Position
Correct screen position with
.
Sets to detect the input signal
automatically. The Enable/Disable
Input Signal
setting is toggled by selecting the
icon.
Resets the adjustment values to the
factory settings.
Color
Independent setting and saving of
Color Menu color adjustment are available for
each CAL Switch mode.
Mode*
Brightness
Contrast
Gain
Advanced
Selects the best display mode easily
according to monitor’s application.
Each time you press the button, the
mode is switched.
Adjusts the screen brightness.
Adjustable range: 0 to 100%
Adjusts the contrast.
Adjustable range: 0 to 100%
Determines the mixing rate of red,
green and blue, and adjust the color
tone.
Adjustable range: 0 to 100%
Allows you to determine the
mixing rate of red.
Allows you to determine the
mixing rate of green.
Allows you to determine the
mixing rate of blue.
Attention
Reset
• After resetting, you cannot undo the
operation.
All : Resets all adjustments to
the default settings (factory
settings).
Color (DICOM*) : Only the
adjustment values in the
current CAL Switch mode will
revert to the default settings
(factory settings).
* Current CAL Switch mode is displayed.
Adjusts each function of hue and
saturation.
Chapter 1 Overview and Features
Icon
Function
Overview
Settings
Language
Selects a language for the
adjustment menu or displaying
message. The language setting is
toggled by selecting the icon.
PowerSave
Auto
EcoView
The sensor on the front side of the
monitor detects the environmental
brightness to adjust the screen
brightness automatically and
comfortably by using the Auto
EcoView function. The Enable/
Disable setting is toggled by
selecting the icon.
Sets the power indicator (blue) ON/
OFF in the monitor ON condition.
Power LED
The On/Off setting is toggled by
selecting the icon.
Off Timer
Turns off the monitor automatically
after a specified time has passed.
This function serves to protect the
monitor from after-images caused
when the same image is left
displayed for a long time. Use this
function when an image is displayed
throughout the day.
Adjustable range: Off, 1 to 23h
Screen
Sharpness
10
Emphasizes the outline of the image
by emphasizing the color difference
between the pixels composing the
image and to improve a sense of
quality and materiality. Contrarily,
this function allows you to show
the image smoothly by blurring the
outline of the image.
Chapter 1 Overview and Features
Chapter 2 Settings and Adjustments
2-1 Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk contents and the overview
of the application software programs.
● Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme.txt” file on the
disk for software startup procedures or file access procedures.
Item
Overview
A “Readme.txt” file
RadiCS LE (for Windows)
RadiCS LE is quality control software used to calibrate the monitor and manage
the calibration history.
(A PC must be connected to the monitor with the supplied USB cable.) Refer to
the description later.
ScreenManager Pro for Medical
(for Windows)
A utility software program to control monitor adjustments from a PC using its
mouse and keyboard.
(A PC must be connected to the monitor with the supplied USB cable.) Refer to
the description later.
User’s Manual of this monitor (PDF file)
● To use RadiCS LE or ScreenManager Pro for Medical
Refer to the corresponding User's Manual on the CD-ROM disk in order to install and use the software.
When using this software, you will need to connect a PC to the monitor with the supplied USB cable.
[Connection]
(1) Connect the USB port (downstream) of a USB compatible PC (or other
USB hub) and the monitor’s USB port (upstream) with the supplied
USB cable.
(2) The USB function is set up automatically upon connection of the USB
cable.
Upstream
Chapter 2 Settings and Adjustments
11
2-2 Screen Adjustment
Digital Input
When digital signals are input, images are displayed correctly based on the preset data of
the monitor. When performing the advanced adjustment, see “2-3 Color Adjustment”
(page 15) and its subsequence pages.
Attention
Analog Input
The monitor screen adjustment is used to suppress flickering of the screen or adjust
screen position and screen size correctly according to the PC to be used.
To use the monitor comfortably, adjust the screen when the monitor is set up for the first
time or when the settings of the PC in use are updated. No adjustment is required when
• Wait 30 minutes or more from
monitor power on before starting
adjustments.
• Auto adjust function does not work
for the images under the resolution of
800 × 600 (SVGA).
the image appears correctly.
The auto adjust function works in the following cases:
• When a signal is input into the monitor for the first time
• When the resolution or Vertical/Horizontal Frequency of input signals
is changed
[Adjustment Procedure]
1 Perform the AutoSize adjustment.
Attention
● To adjust flickering, screen position, and screen size
automatically [AutoSize]
(1) Press
.
The adjustment menu appears.
(2) Select
(3) Select
(Analog).
(AutoSize).
Flickering, screen position, and screen size are adjusted automatically.
(4) After confirming the screen message, select
If you select
(OK).
(Undo), the monitor returns to the pre-adjusted status.
• This function works correctly when
an image is fully displayed over the
Windows or Macintosh display area.
It does not work properly when an
image is displayed only on a part of
the screen (command prompt window,
for example) or when a black
background (wallpaper, etc.) is in use.
• This function does not work correctly
with some graphics boards.
• “Auto in Progress” appears on the
screen during auto adjustment.
If the screen is not displayed correctly even after adjusting in step 1
above, perform the adjustments according to the procedures on the
following pages. When the screen is displayed correctly, go to step 5
“To adjust color gradation automatically [AutoRange]”.
2 Prepare the display pattern for the analog display adjustment.
Download the “Screen adjustment pattern files” from our site:
http://www.radiforce.com
12
Chapter 2 Settings and Adjustments
NOTE
• For details and instructions on opening
the “Screen adjustment pattern files”,
refer to the “Readme.txt” file.
the AutoSize adjustment again with the analog screen
3 Perform
adjustment pattern displayed.
● To adjust flickering, screen position, and screen size
automatically [AutoSize]
(1) Display Pattern 1 of the screen adjustment pattern files in full
screen on the monitor.
(2) Press
.
The adjustment menu appears.
(3) Select
(4) Select
(Analog).
(AutoSize).
Flickering, screen position, and screen size are adjusted automatically.
(5) After confirming the screen message, select
If you select
(OK).
(Undo), the monitor returns to the pre-adjusted status.
If the screen is not displayed correctly even after adjusting in step 3
above, perform the adjustments according to the procedures on the
following pages. When the screen is displayed correctly, go to step 5 “To
adjust color gradation automatically [AutoRange]”.
advanced adjustments by using
4 Perform
adjustment menu.
Select
(Manual) in the
(Manual) to adjust the clock, phase and position, in this order.
● To eliminate vertical bars [Clock]
or
of
(1) Adjust the clock with
vertical bars.
(Clock) to eliminate
● To remove flickering or blurring [Phase]
or
of
(Phase) to remove
(1) Adjust the phase with
flickering or blurring.
NOTE
• Press the control button slowly so as
not to miss the adjustment point.
• When blurring, flickering or bars
appear on the screen after adjustment,
proceed to [Phase] to remove
flickering or blurring.
Attention
• Flickering or blurring may not be
eliminated depending on your PC or
graphics board.
Chapter 2 Settings and Adjustments
13
● To correct screen position [Position]
(Position).
(1) Select
(2) Adjust the position with
(Left) /
(Right) /
(Down) /
(Up) to display the image properly in the display area of the
monitor.
(3) Select
.
The adjustment is completed.
5 Adjust the color gradation.
● To adjust color gradation automatically [AutoRange]
Every color gradation (0 to 255) can be displayed by adjusting the
signal output level.
(1) Display Pattern 2 in full screen on the monitor using the screen
adjustment pattern files.
(2) Press
.
The adjustment menu appears.
(3) Select
(4) Select
(Analog).
(AutoRange).
Color gradation is adjusted automatically.
(5) After confirming the screen message, select
If you select
(6) Close the Pattern 2.
14
(OK).
(Undo), the monitor returns to the pre-adjusted status.
Chapter 2 Settings and Adjustments
NOTE
• Since the number of pixels and the
pixel positions are fixed on the LCD
monitor, only one position is provided
to display images correctly. The
position adjustment is made to shift
an image to the correct position.
• When vertical bars appear on the
screen after adjustment, go back to
“To eliminate vertical bars [Clock]”.
(Clock → Phase → Position)
2-3 Color Adjustment
● To select the display mode (CAL Switch mode)
CAL Switch allows you to select the best display mode easily according to the monitor’s
application.
CAL Switch mode
Mode
Purpose
(DICOM-CL)
DICOM-CL mode. Available for setting tailored to X-ray
film color (clear base).
(TXT)
Text mode. Suitable for displaying texts for word
processing or spreadsheets.
(CUS)
Custom mode. Available for the color settings according
to your preference.
(CAL)
CAL mode. Displays the screen adjusted by calibration
software.
NOTE
(1) Press
.
The adjustment menu appears.
(2) Press
again while the adjustment menu is displayed.
Each time you press the button, the mode is switched.
(3) Select
.
The mode selected is set.
• You can also select the CAL Switch
mode by pressing
and select
(Color).
• “ScreenManager Pro for Medical”
allows you to select the CAL Switch
mode automatically according to the
application used.
(Refer to “Chapter 3 Auto CAL
Switch” on the User’s Manual for
“ScreenManager Pro for Medical”.)
Chapter 2 Settings and Adjustments
15
● To perform advanced adjustments
Attention
Independent setting and saving of color adjustment are available for each CAL Switch
mode.
● Adjustment items in each mode
According to the CAL Switch mode selected, the adjustable function differs.
√: Adjustment available
Icon
−: Invalid for adjustment
Function
CAL Switch mode
DICOM-CL
TXT
CUS
CAL
−
−
−
−
−
−
−
√
√
√
√
√
√
−
−
−
−
−
−
−
Brightness
Contrast
Gamma
Temperature
Gain
Saturation
Hue
√
√
−
−
−
√
√
√
• Wait 30 minutes or more from
monitor power on before starting the
color adjustment.
• Perform
(AutoRange) first
when adjusting color for analog input
signals.
(Refer to “To adjust color gradation
automatically” on page 14).
• The same image may be seen in
different colors on multiple monitors
due to their monitor-specific
characteristics. Make fine color
adjustment visually when matching
colors on multiple monitors.
NOTE
• The values shown in “%” or “K” are
available only as reference.
* If
you adjust the calibration in this mode using the calibration kit exclusive for to this monitor (RadiCS LE as an accessory shown on page 33), only Brightness and Reset is adjustable.
● To adjust the brightness [Brightness]
NOTE
The screen brightness is adjusted by changing the brightness of the backlight (Light
source from the LCD back panel).
Adjustable range: 0 to 100%
(1) Press
.
The adjustment menu appears.
(2) Select
(Color).
(3) Adjust the brightness with
(4) Select
.
or
The adjustment is completed.
16
Chapter 2 Settings and Adjustments
of
(Brightness).
• You can also adjust the brightness
by pressing
or
without
displaying the adjustment menu.
● To adjust the contrast [Contrast]
NOTE
• You can also adjust the contrast by
pressing
while the adjustment
menu is not displayed, and press
or
of
(Contrast).
• In the contrast of 50%, every color
gradation is displayed.
• When adjusting the monitor, it
is recommended to perform the
brightness adjustment which may
not lose the gradation characteristics,
prior to the contrast adjustment.
Perform the contrast adjustment in the
following cases.
–When you feel the image is dark
even if the brightness is set to
100%.
–When you feel the black level of the
screen is bright (Set the brightness
down and the contrast to higher
than 50%).
The luminance of the screen is adjusted by varying the video signal level.
Adjustable range: 0 to 100%
(1) Press
.
The adjustment menu appears.
(2) Select
(Color).
(3) Adjust the contrast with
(4) Select
.
of
or
(Contrast).
The adjustment is completed.
● To adjust the gamma value [Gamma]
NOTE
The gamma value can be adjusted. The luminance of the monitor varies depending on
the input signal, however, the variation rate is not proportional to the input signal. To
keep the balance between the input signal and the luminance of the monitor is called as
“Gamma correction”.
• You cannot adjust the value if the
icon is not displayed, depending on
the CAL Switch mode selected. (See
“Adjustment items in each mode” on
page 16.)
Adjustable range: 1.8, 2.0, 2.2
(1) Press
.
The adjustment menu appears.
(2) Select
(Color).
(3) Select
(Color Menu).
(4) Adjust the gamma value with
(5) Select
.
or
of
(Gamma).
The adjustment is completed.
Chapter 2 Settings and Adjustments
17
● To adjust the color temperature [Temperature]
NOTE
The color temperature can be adjusted. The color temperature is normally used to
express the hue of “White” and/or “Black” by a numerical value. The value is expressed
in degrees “K” (Kelvin).
In the same way as the flame temperature, the image on the monitor is displayed reddish
if the color temperature is low and is bluish if the color temperature is high. The gain
preset values are set for each color temperature setting value.
6500K
The white color image is displayed in warm white like paper white.
The temperature is suitable to display photographs or video
images.
9300K
The white color image is displayed slightly bluish white.
Adjustable range: Native, 6500K-15000K (specified by every 500K unit,
including 9300K), User (at gain adjustment)
(1) Press
• You cannot adjust the value if the
icon is not displayed, depending on
the CAL Switch mode selected. (See
“Adjustment items in each mode” on
page 16.)
• [Gain] allows you to perform more
advanced adjustment (See “To adjust
the gain value” on page 18).
• If you set to [Native], the image is
displayed in the preset color of the
monitor (Gain: 100% for each RGB).
• When changing the gain value, the
color temperature adjusting range is
changed to “User”.
.
The adjustment menu appears.
(2) Select
(Color).
(3) Select
(Color Menu).
(4) Adjust the color temperature with
(5) Select
.
or
of
(Temperature).
The adjustment is completed.
● To adjust the gain value [Gain]
NOTE
Each luminance of red/green/blue composing the color is called “Gain”. The gain
adjustment may change the color tone of the “White” (when the max input signal for
each color is obtained)
Adjustable range: 0 to 100%
(1) Press
.
The adjustment menu appears.
(2) Select
(Color).
(3) Select
(Color Menu).
(4) Select
(Gain).
(5) Adjust the respective value of
or
.
(6) Select
.
(Red)/
(Green)/
• You cannot adjust the value if the
icon is not displayed, depending on
the CAL Switch mode selected. (See
“Adjustment items in each mode” on
page 16.)
• The gain value may change depending
on the value of the color temperature.
• When changing the gain value, the
color temperature adjusting range is
changed to “User”.
(Blue) with
The adjustment is completed.
● To adjust the color saturation [Saturation]
This function allows you to adjust the saturation of the color on the monitor.
Adjustable range: -100 to 100
(1) Press
NOTE
.
The adjustment menu appears.
(2) Select
(Color).
(3) Select
(Color Menu).
(4) Select
(Advanced).
(5) Adjust the saturation with
(6) Select
.
or
of
The adjustment is completed.
18
Attention
• This function does not enable to
display every color gradation.
Chapter 2 Settings and Adjustments
(Saturation).
• You cannot adjust the value if the
icon is not displayed, depending on
the CAL Switch mode selected. (See
“Adjustment items in each mode” on
page 16.)
• Setting the minimum (-100) turns the
image to a monochrome screen.
● To adjust the hue [Hue]
Attention
This function allows you to adjust the hue. If you set the hue to a high value, the image
turns greenish. If low, the image turns purplish.
NOTE
Adjustable range: -100 to 100
(1) Press
• You cannot adjust the value if the
icon is not displayed, depending on
the CAL Switch mode selected. (See
“Adjustment items in each mode” on
page 16.)
.
The adjustment menu appears.
(2) Select
(Color).
(3) Select
(Color Menu).
(4) Select
(Advanced).
(5) Adjust the hue with
or
(6) Select
.
• This function does not enable to
display every color gradation.
of
(Hue).
The adjustment is completed.
Chapter 2 Settings and Adjustments
19
2-4 Adjusting Sharpness [Sharpness]
This function allows you to emphasize the outline of the image by emphasizing the color
difference between the pixels composing the image and to improve a sense of quality
and materiality. Contrarily, this function allows you to show the image smoothly by
blurring the outline of the image.
Adjustable range: -3 to 3
(1) Press
.
The adjustment menu appears.
(2) Select
(Screen).
(3) Adjust the sharpness with
(4) Select
.
of
or
(Sharpness).
The adjustment is completed.
2-5 Setting Enable/Disable for the automatic
brightness adjustment function [Auto EcoView]
The sensor on the front side of the monitor detects the environmental brightness to adjust
the screen brightness automatically and comfortably by using the Auto EcoView
function.
(1) Press
.
The adjustment menu appears.
(2) Select
(PowerSave).
(3) The Enable/Disable setting is toggled by selecting
(Auto EcoView).
Enable
Disable
(4) Select
.
The mode selected is set.
2-6 Turning off the monitor automatically
[Off Timer]
This function allows the monitor to automatically turn off after a specified time has
passed. This function serves to protect the monitor from after-images caused when the
same image is left displayed for a long time. Use this function when an image is
displayed throughout the day.
Adjustable range: Off, 1 to 23h
(1) Press
.
The adjustment menu appears.
(2) Select
(PowerSave).
(3) Set a monitor OFF time with
or
Select “Off” to set Off timer setting to “Off”.
of
(Off Timer).
(4) Select
The Off timer setting is completed.
(5) “Power will shut off in a minute” appears on the display if it becomes one
minute before the setting time.
If you select
20
(Extend), the off timer function works 90 minutes later.
Chapter 2 Settings and Adjustments
Attention
• This function is not available in the
DICOM-CL and CAL modes.
Attention
2-7 Locking Buttons [Key Lock] [Menu Lock]
This function allows you to lock the operation buttons to prevent changing the adjusted/
• The key lock function may activate
when calibration is performed with
the calibration kit.
set status.
Key Lock : Locks the buttons other than the Power button.
Menu Lock :Locks the buttons other than the Power, Input signal selection
and Mode buttons.
(1) Press
(2) Press
to turn off the monitor.
holding
down to turn on the monitor.
The adjustment menu appears.
(3) Each time you press
, the mode is switched.
Unlock
Menu Lock
Key Lock
(4) Select
.
The mode selected is set.
2-8 Displaying Monitor Infomation [Info1] [Info2]
This function allows you to display the input signal status, current resolution and model
name.
Info1 : D
isplays the input signal status (analog/digital), resolution, H/V
frequency
Info2 : Displays the model name, usage time and serial number.
(1) Press
.
The adjustment menu appears.
(2) Select
(3) Select
(4) Select
(Tool).
(Info1) or
(Info2).
.
The menu is closed.
Chapter 2 Settings and Adjustments
21
2-9 Setting Power Indicator ON/OFF [Power LED]
This function allows you to set the power indicator (blue) ON/OFF in the monitor ON
condition.
(1) Press
.
The adjustment menu appears.
(2) Select
(PowerSave).
(3) The On/Off setting is toggled by selecting
(Power LED).
On
Off
(4) Select
.
The mode selected is set.
2-10 Setting Language [Language]
This function allows you to select a language for the adjustment menu or displaying
message.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Simplified Chinese/Traditional
Chinese/Japanese
(1) Press
.
The adjustment menu appears.
(2) Select
(Settings).
(3) The language setting is toggled by selecting
(Language).
English
German
French
Spanish
Italian
Swedish
Simplified Chinese
Traditional Chinese
Japanese
(4) Select
.
The language selected is set.
2-11 Displaying EIZO logo
The EIZO logo appears on the display when turning on the monitor. This function allows
you to display, or not, the EIZO logo.
(1) Press
(2) Press
to turn off the monitor.
holding
down to turn on the monitor.
The EIZO logo display setting is toggled by performing the operation in step 2.
22
Chapter 2 Settings and Adjustments
NOTE
• The logo appears with the default
setting.
2-12 Resuming the Default Setting [Reset]
There are two types of Reset. One is to reset the color adjustment only to the default
settings, and the other is to reset all the settings to the default settings.
Attention
• After resetting, you cannot undo the
operation.
● To reset color adjustment values
Only the adjustment values in the current CAL Switch mode will revert to the default
settings (factory settings).
(1) Press
.
The adjustment menu appears.
(2) Select
(3) Select
(Tool).
(Reset).
If you will not perform the reset operation, select
(4) Select
.
(Color (DICOM*)).
The color adjustment values revert to the default settings.
* Current CAL Switch mode is displayed.
● To reset all adjustments to the factory default settings
Reset all adjustments to the factory default settings.
(1) Press
.
The adjustment menu appears.
(2) Select
(3) Select
(Tool).
(Reset).
If you will not perform the reset operation, select
(4) Select
.
(All).
All setting values revert to the default settings.
Chapter 2 Settings and Adjustments
23
Chapter 3 Connecting Cables
3-1 Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the DVI-D and the D-Sub mini 15 pin
connector on the back of the monitor.
Connection examples
DVI-D connector
D-Sub mini
15-pin Connector
To PC 1
To PC 2
D-Sub mini 15-pin
Connector
DVI connector
Signal cable
(Digital) FD-C39
Signal cable
MD-C87
● To switch the input signal
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right corner of
the screen.
24
Chapter 3 Connecting Cables
● Setting auto-selection of the input signal [Input Signal]
Enable : When either PC is turned off or enters the power-saving mode, the monitor
automatically displays signals of another PC.
Disable : The monitor does not detect the PC’s signals automatically. Switch an input
signal with
(1) Press
NOTE
• When “Enable” is selected for [Input
Signal], the monitor’s power-saving
function works only when the two
PCs are in the power-saving mode.
.
.
The adjustment menu appears.
(2) Select
(Tool).
(3) The Enable/Disable setting is toggled by selecting
(Input Signal).
Enable
Disable
(4) Select
.
The mode selected is set.
Chapter 3 Connecting Cables
25
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
• No-picture problems → See No.1 - No.2.
• Imaging problems (digital input) → See No.3 - No.9.
• Imaging problems (analog input) → See No.3 - No.12.
• Other problems → See No.13 - No.14.
• USB problems → See No.15.
Problems
1. No picture
• Power indicator does not light.
Possible cause and remedy
• Check whether the power cord is connected correctly. If
the problem persists, turn off the monitor, and then turn it
on again a few minutes later.
• Press
.
• Power indicator is lighting blue.
• Set each adjusting value in [Brightness], [Contrast] and
[Gain] to higher level. (see page 16, 17, 18)
• Power indicator is lighting orange.
.
• Switch the input signal with
• Operate the mouse or keyboard.
• Check whether the PC is turned on.
2. The message below appears.
This message appears when the signal is not input
correctly even when the monitor functions properly.
• This message appears when no signal is input.
• The message shown left may appear, because some
PCs do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal with
.
• The message shows that the input signal is out of the
specified frequency range. (Such signal frequency is
displayed in yellow.)
Example:
• Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
monitor. (See “Compatible Resolutions/Frequencies” on
the cover back of the Setup Manual.)
• Reboot the PC.
• Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
fD:Dot Clock
(Displayed only when the digital signal inputs)
fH:Horizontal Frequency
fV:Vertical Frequency
3. The screen is too bright or too dark.
• Adjust using [Brightness] or [Contrast]. (The LCD
monitor backlight has a fixed life span. When the screen
becomes dark or begins to flicker, contact your local
dealer.)
4. Characters are blurred.
• Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
monitor. (See “Compatible Resolutions/Frequencies” on
the cover back of the Setup Manual.)
• Adjust using [Sharpness]. (see page 20)
5. Afterimages appear.
• Use a screen saver or off timer function for a long-time
image display.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
6. Green/red/blue/white dots or defective dots remain • This is due to LCD panel characteristics and is not a
on the screen.
failure.
26
Chapter 4 Troubleshooting
Problems
Possible cause and remedy
7. Interference patterns or pressure marks remain on • Leave the monitor with a white or black screen. The
the screen.
symptom may disappear.
8. The outline of the letters are colored.
• If the [Sharpness] setting is set to a high level, the
characters displayed on the monitor may be colored.
9. Noise appears on the screen.
• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
10. Display position is incorrect.
• Adjust image position so that it is displayed properly
within the display area using [Position]. (See page 14)
• If the problem persists, use the graphics board’s utility if
available to change the display position.
11. Vertical bars appear on the screen or a part of the
image is flickering.
• Adjust using [Clock]. (see page 13)
12. Whole screen is flickering or blurring.
• Adjust using [Phase]. (see page 13)
13. The adjustment menu does not appear.
• Check whether the operation lock function works.
(see page 21)
14. The auto adjust function does not work correctly.
• This function does not work when digital signal is input.
• This function is intended for use on the Macintosh and
on AT-compatible PC running Windows. It may not work
properly in either of the following cases. It does not work
properly when an image is displayed only on a part of the
screen (command prompt window, for example) or when
a black background (wallpaper, etc.) is in use.
• This function does not work correctly with some graphics
boards.
15. The monitor connected with the USB cable is not
detected.
• Check whether the USB cable is connected correctly.
• Please perform the following to check the status.
- Reboot the PC.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 4 Troubleshooting
27
Chapter 5 Reference
5-1 Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) to be attached to
the monitor. Use an arm or stand of EIZO option.
[Attaching]
the LCD monitor on a soft cloth spread over on a stable
1 Lay
surface with the panel surface facing down.
2 Remove the stand. (Prepare a screwdriver.)
Unscrew the four screws securing the unit and the stand with the
screwdriver.
3 Attach the monitor to the arm or stand.
Secure the monitor to the arm or stand using the screws specified in the
user’s manual of the arm or stand.
28
Chapter 4 Troubleshooting
Attention
• When attaching an arm or stand,
follow the instructions of their user’s
manual.
• When using another manufacturer’s
arm or stand, confirm the following in
advance and select one conforming to
the VESA standard. Use the M4 × 12
mm screws supplied with this monitor.
– Clearance between the screw holes:
100 mm × 100 mm
–Thickness of plate: 2.6 mm
–Strong enough to support weight of
the monitor unit (except the stand)
and attachments such as cables.
• When using an arm or stand, attach it
to meet the following tilt angles of the
monitor.
–Up 45 degrees, down 45 degrees
(horizontal display, and vertical
display rotated 90 degrees
clockwise)
• Connect the cables after attaching an
arm or a stand.
• Since the monitor and arm are so
heavy, dropping them may result in
injury or equipment damage.
5-2 Power Saving Mode
■Analog input
This monitor complies with the VESA DPMS standard.
[Power Saving System]
Attention
PC
Monitor
Operating
Power saving
STAND-BY
SUSPENDED
OFF
Power
Indicator
Operating
Blue
Power saving
Orange
• Unplugging the power cord
completely shuts off power supply to
the monitor.
[Resumption Procedure]
• Operate the mouse or keyboard to resume the normal screen.
■Digital input
This monitor complies with the DVI DMPM standard.
[Power Saving System]
The monitor enters the power saving mode in five seconds in connection with the PC
setting.
PC
Operating
Power saving
Monitor
Operating
Power saving
Power Indicator
Blue
Orange
[Resumption Procedure]
• Operate the mouse or keyboard to resume the normal screen.
Chapter 5 Reference
29
5-3 Specifications
LCD Panel
Size
19-inch (480 mm) TFT color LCD with
Surface treatment
anti-glare
Surface hardness
3H
Viewing angle
Horizontal 178°, Vertical 178° (CR:10 or more)
Dot Pitch
0.294mm
Response Time
Approx. 20ms
Horizontal Scan
Frequency
Analog
24.8-80kHz
Digital
31-64kHz
Vertical Scan
Frequency
Analog
50-75Hz
Digital
59-61Hz (VGA TEXT: 69-71Hz)
Resolution
Max. Dot Clock
1280 dots × 1024 lines
Analog
135MHz
Digital
108MHz
Max. Display Color
Approx. 16.77 million colors
Display Area (H × V)
376.3mm × 301.0mm
Power Supply
100-120 VAC ±10%, 50/60Hz 0.7-0.6A
200-240 VAC ±10%, 50/60Hz 0.4-0.35A
Power
Consumption
Screen Display On
43W or less
Power saving mode
0.8W or less (for single signal input without USB)
Power button Off
0.7W or less (Without USB)
Input Signal Connector
DVI-D connector (Applicable to HDCP), D-Sub mini 15-pin
Analog Input Signal (Sync)
Separate, TTL, positive/ negative
Analog Input Signal (Video)
Analog, Positive (0.7Vp-p/75Ω)
Digital Signal Transmission System
TMDS (Single Link)
Video Signal Memory
Analog signal: 26 (preset: 21)
Plug & Play
VESA DDC 2B / EDID structure 1.3
Dimensions
Main unit
(Width) × (Height) ×
(Depth)
Main unit (without
stand)
405 mm (15.9 inch) × 406.5 - 506.5 mm (16.0 - 19.9 inch) × 205 mm
(8.1 inch)
Mass
Main unit
7.2 kg (15.9 lbs.)
Main unit (without
stand)
5.2 kg (11.5 lbs.)
Movable range
Environmental
Conditions
30
405 mm (15.9 inch) × 334 mm (13.1 inch) × 61.5 mm (2.4 inch)
Tilt: 30° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 100 mm (3.9 inch)
Rotation: 90° (clockwise)
Temperature
Operating temperature: 0 °C - 35 °C (32 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F)
Humidity
Operating: 20% - 80% (no condensation)
Storage: 10% - 80% (no condensation)
Pressure
Operating: 700 to 1060 hPa.
Storage: 200 to 1060 hPa.
Chapter 5 Reference
USB
Standard
USB Specification Revision 2.0
Port
Upstream port × 1
Main default settings (factory settings)
CAL Switch Mode : The default display mode setting is DICOM mode.
Brightness
Custom
Text
DICOM-CL
CAL
Color Temperature
approx. 300 cd/m2 (100 %)
approx. 100 cd/m2 (40 %)
170 cd/m2
170 cd/m2
Native
7500K
7500K
7500K
Gamma
2.2
2.2
DICOM setting
DICOM setting
others
Auto EcoView
Disable
Off Timer
Disable
Input Signal
Disable
Language
English
Sharpness
0
Outside Dimensions
374 (14.7)
172 (6.8)
38.5 (1.52)
61.5 (2.42)
unit : mm (inch)
SWIVEL
35°
35°
TILT 3
0°
239 (9.4)
320 (12.6)
405 (15.9)
378.4 (14.9)
13.3 (0.52)
15.5
(0.61)
13.3 (0.52)
100 (3.9)
152.5 (6.0)
100 (3.9)
117 (4.6)
130.5 (5.1)
73.3 (2.89)
7.8 (0.31)
37.8 (1.49)
15.5 (0.61)
240.3 (9.5)
100 (3.9)
303 (11.9)
334 (13.1)
406.5 ~506.5 (16~19.9)
442.8~542.8 (17.4~21.4)
117 (4.6)
152.5 (6.0)
Chapter 5 Reference
31
Connector Pin Assignment
• DVI-D connector
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
1
T.M.D.S. Data 2-
9
T.M.D.S. Data1-
17
T.M.D.S. Data0-
2
T.M.D.S. Data 2+
10
T.M.D.S. Data1+
18
T.M.D.S. Data0+
3
T.M.D.S. Data2/4 Shield
11
T.M.D.S. Data1/3 Shield
19
T.M.D.S. Data0/5 Shield
4
NC*
12
NC*
20
NC*
5
NC*
13
NC*
21
NC*
6
DDC Clock (SCL)
14
+5V Power
22
T.M.D.S. Clock shield
7
DDC Data (SDA)
15
Ground (return for +5V,
Hsync, and Vsync)
23
T.M.D.S. Clock+
8
NC*
16
Hot Plug Detect
24
T.M.D.S. Clock(NC*: No Connection)
• D-Sub mini 15-pin connector
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
1
Red video
6
Red video ground
11
Ground
2
Green video
7
Green video ground
12
Data (SDA)
3
Blue video
8
Blue video ground
13
H. Sync
4
Ground
9
NC*
14
V. Sync
5
NC*
10
Ground
15
Clock (SCL)
(NC*: No Connection)
• USB port
Upstream
Series B connector
Contact No.
32
Signal
Remarks
1
VCC
Cable power
2
– Data
Serial data
3
+ Data
Serial data
4
Ground
Cable ground
Chapter 5 Reference
Option List
Panel Protector
EIZO “FP-702”
Arm, Stand
EIZO “LS-H71-D” : Height Adjustable Stand
EIZO “LS-H72-D” : Height Adjustable Stand
EIZO “LS-A70-D” : Height Adjustable Stand
EIZO “LS-HM1-D” : Dual Height Adjustable Stand
EIZO “LA-120-D” : LCD Monitor Flexible Arm
EIZO “LA-130-D” : LCD Monitor Flexible Arm
EIZO “LA-131-D” : LCD Monitor Flexible Arm
EIZO “LA-010-W-BK” : Wall Mount Arm for LCD Monitor
EIZO “LA-011-W” : Wall Mount Arm for LCD Monitor
EIZO “LA-012-W” : Wall Mount Arm for LCD Monitor
EIZO “LA-030-W” : Wall Mount Arm for LCD Monitor
Calibration Kit
EIZO “RadiCS UX1” Ver.3.4.1 or later
EIZO “Clip-On Swing Sensor G1”
EIZO “Clip-On Swing Sensor G2”
Network QC Management
Software
EIZO “RadiNET Pro” Ver.3.4.1 or later
Cleaning Kit
EIZO “ScreenCleaner”
Refer to Web site of EIZO NANAO CORPORATION for the latest information about supported graphics card
(http://www.radiforce.com).
Chapter 5 Reference
33
5-4 Glossary
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in
use, when the analog input signal is converted to a digital signal for image display.
This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DICOM (Digital Imaging and Communication in Medicine)
DICOM is a standard for digital imaging and communication for medical use developed by American College of
Radiology and National Electric Manufacturers Association.
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is
a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal
inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active Off
(power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light
passing through the panel color filter. Red, green and blue are the three primary colors. All the colors on the screen
are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume)
passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a highcontrast image.
HDCP (High-bandwidth Digital Contents Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps
to transmit the digital contents safely by coding the digital contents sent via DVI terminal on the output side and
decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable
to HDCP system.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to
adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that range
adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor
consists of 1280 horizontal pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are illuminated
as a full screen (1:1).
34
Chapter 5 Reference
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen
becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling)
VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. DPMS
defines the signal status between PC and monitor.
Chapter 5 Reference
35
5-5 Preset Timing
The following table shows factory preset video timing (for analog signal only).
Mode
Dot clock
VGA 640×[email protected]
25.2 MHz
VGA 720×[email protected]
28.3 MHz
VESA 640×[email protected]
31.5 MHz
VESA 640×[email protected]
31.5 MHz
VESA 800×[email protected]
36.0 MHz
VESA 800×[email protected]
40.0 MHz
VESA 800×[email protected]
50.0 MHz
VESA 800×[email protected]
49.5 MHz
VESA 1024×[email protected]
65.0 MHz
VESA 1024×[email protected]
75.0 MHz
VESA 1024×[email protected]
78.8 MHz
VESA 1152×[email protected]
108.0 MHz
VESA 1280×[email protected]
108.0 MHz
VESA 1280×[email protected]
108.0 MHz
VESA 1280×[email protected]
135.0 MHz
PC-9801 640 × [email protected]
21.1 MHz
PC-9821 AP2 640 × 400
@70Hz
25.2 MHz
36
Chapter 5 Reference
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Frequency
Horizontal: kHz
Vertical: Hz
31.47
59.94
31.47
70.09
37.86
72.81
37.50
75.00
35.16
56.25
37.88
60.32
48.08
72.19
46.88
75.00
48.36
60.00
56.48
70.07
60.02
75.03
67.50
75.00
60.00
60.00
63.98
60.02
79.98
75.03
24.83
56.42
31.48
70.10
Polarity
Negative
Negative
Negative
Positive
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Negative
Negative
Attention
• Display position may be deviated
depending on the PC connected,
which may require screen adjustment
using Adjustment menu.
• If a signal other than those listed in
the table is input, adjust the screen
using the Adjustment menu. However,
screen display may still be incorrect
even after the adjustment.
• When interlace signals are used, the
screen cannot be displayed correctly
even after screen adjustment using the
Adjustment menu.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: RadiForce MX191
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
*
*
*
*
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the
limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (Enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
37
EMC Information
Essential performance of RadiForce series is to display images and operate functions normally.
CAUTION
The RadiForce series requires special precautions regarding EMC and need to be installed, put into
service and used according to the following information.
Do not use any cables other than the cables that provided or specified by us.
Using other cables may cause the increase of emission or decrease of immunity.
Do not put any portable and mobile RF communications equipment close to the RadiForce series.
Doing so may affect the RadiForce series.
The RadiForce series should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary, the equipment or system should be observed to verify normal operation
in the configuration in which it will be used.
Anyone who connects additional equipment to the signal input part or signal output parts,
configuring a medical system, is responsible that the system complies with the requirements of
EN60601-1-2.
Guidance and manufacturer’s declaration - electromagnetic emissions
The RadiForce series is intended for use in the electromagnetic environment specified below.
The customer or the user of the RadiForce series should assure that it is used in such an environment.
Emission test
Compliance Electromagnetic environment - guidance
RF emissions
CISPR11/EN55011
Group 1
RF emissions
Class B
CISPR11/EN55011
Harmonic emissions Class D
IEC/EN61000-3-2
Voltage fluctuations / Complies
flicker emissions
IEC/EN61000-3-3
The RadiForce series uses RF energy only for its internal function.
Therefore, its RF emission are very low and are not likely to cause any
interference in nearby electronic equipment.
The RadiForce series is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage power
supply network that supplies buildings used for domestic purposes.
Guidance and manufacturer’s declaration - electromagnetic immunity
The RadiForce series is intended for use in the electromagnetic environment specified below.
The customer or the user of the RadiForce series should assure that it is used in such an environment.
Immunity test
IEC/EN60601 test
level
Compliance level
Electromagnetic environment - guidance
Electrostatic
discharge (ESD)
IEC/EN61000-4-2
±6kV contact
±8kV air
±6kV contact
±8kV air
Floors should be wood, concrete or ceramic tile.
If floors are covered with synthetic material, the
relative humidity should be at least 30%.
Electrical fast
transient / burst
IEC/EN61000-4-4
±2kV
for power supply lines
±1kV
for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
±2kV
for power supply lines
±1kV
for input/output lines
±1kV line(s) to line(s)
±2kV line(s) to earth
Mains power quality should be that of a typical
commercial or hospital environment.
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in UT)
for 5 cycles
70% UT (30% dip in UT)
for 25 cycles
<5% UT (>95% dip in
UT) for 5sec
3A/m
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in
UT) for 5 cycles
70% UT (30% dip in
UT) for 25 cycles
<5% UT (>95% dip in
UT) for 5sec
3A/m
Mains power quality should be that of a typical
commercial or hospital environment. If the user
of the RadiForce series requires continued
operation during power mains interruptions, it
is recommended that the RadiForce series be
powered from an uninterruptible power supply or a
battery.
Surge
IEC/EN61000-4-5
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC/EN61000-4-11
Mains power quality should be that of a typical
commercial or hospital environment.
Power frequency
Power frequency magnetic fields should be at
(50/60Hz)
levels characteristic of a typical location in a
magnetic field
typical commercial or hospital environment.
IEC/EN61000-4-8
NOTE UT is the a.c. mains voltage prior to application of the test level.
38
Guidance and manufacturer’s declaration - electromagnetic immunity
The RadiForce series is intended for use in the electromagnetic environment specified below. The customer or the user
of the RadiForce series should assure that it is used in such an environment.
Immunity test
IEC/EN60601 test
level
Compliance level
Electromagnetic environment - guidance
Conducted RF
IEC/EN61000-4-6
3Vrms
150kHz to 80MHz
3Vrms
Radiated RF
IEC/EN61000-4-3
3V/m
80MHz to 2.5GHz
3V/m
Portable and mobile RF communications
equipment should be used no closer to any part
of the RadiForce series, including cables, than
the recommended separation distance calculated
from the equation applicable to the frequency of
the transmitter.
Recommended Separation distance
d = 1.2 √ P
d = 1.2 √ P, 80MHz to 800MHz
d = 2.3 √ P, 800MHz to 2.5GHz
Where “P” is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and “d” is the
recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site surveya,
should be less than the compliance level in each
frequency rangeb.
Interference may occur in the vicinity of equipment
marked with the following symbol.
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the RadiForce series is used exceeds the applicable
RF compliance level above, the RadiForce series should be observed to verify normal operation. If abnormal
performance is observed, additional measures may be necessary, such as reorienting or relocating the RadiForce
series.
b
Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
39
Recommended separation distances between portable and mobile RF communications equipment
and the RadiForce Series
The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances
are controlled. The customer or the user of the RadiForce series can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the
RadiForce series as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output
Separation distance according to frequency of transmitter
power of transmitter
m
150kHz to 80MHz
80MHz to 800MHz
800MHz to 2.5GHz
W
d = 1.2 √ P
d = 1.2 √ P
d = 2.3 √ P
0.01
0.12
0.12
0.23
0.1
0.38
0.38
0.73
1
1.2
1.2
2.3
10
3.8
3.8
7.3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the recommended separation distance “d”
in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where “P” is
the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects and people.
Cable length
Power Cord :
Signal Cable (FD-C39) :
Signal Cable (MD-C87) :
USB Cable (MD-C93) :
40
Accessary
Accessary
Accessary
Accessary
2.0m
2.0m
1.8m
1.8m
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement