ESIM364 Installation Manual (updated 2013.04.10)

ESIM364 Installation Manual (updated 2013.04.10)
ESIM364
GSM ALARM AND MANAGEMENT SYSTEM
INSTALLATION MANUAL
COMPLIES WITH EN 50131-1 GRADE 3, CLASS II REQUIREMENTS
Installation Manual v1.6
Valid for ESIM364 v02.07.00 and up
Safety instructions
Please read and follow these safety guidelines in order to maintain safety of operators and people around:
• GSM alarm & management system ESIM364 (also referenced as alarm system, system or device) has radio transceiver operating in GSM
850/900/1800/1900 bands.
• DO NOT use the system where it can be interfere with other devices and cause any potential danger.
• DO NOT use the system with medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.
• DO NOT attempt to personally repair the system.
• System label is on the bottom side of the device.
GSM alarm system ESIM364 is a device mounted in limited access areas. Any system repairs must be done only by qualified,
safety aware personnel.
The system must be powered by main 16-24V 50 Hz ~1.5A max or 18-24V
1,5A max DC power supply which must be
approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the
system, switching the pole terminals places does not have any affect.
Any additional devices linked to the system ESIM364 (computer, sensors, relays etc.) must be approved by LST EN 60950-1
standard.
Main power supply can be connected to AC mains only inside installation room
with automatic 2-pole circuit breaker capable of disconnecting circuit in the
event of short circuit or over-current condition. Open circuit breaker must have a
gap between connections of more than 3mm and the disconnection current 5A.
Phase
Null
PE
AC/DC
AC 230V
50 Hz/DC 24V
ESIM364
USB cable
Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installation
or maintenance must not be done during stormy conditions
Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one of
battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching the
pole terminals places is NOT allowed.
In order to avoid fire or explosion hazards the system must be used only with approved backup battery.
The device is fully turned off by disconnecting 2-pole switch off device of the main power supply and disconnecting backup
battery connector.
Fuse F1 type – Slow Blown 3A. Replacement fuses have to be exactly the same as indicated by the manufacturer.
If you use I security class computer for setting the parameters it must be connected to earth.
The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that
the product must not be disposed of together with household waste. To prevent possible harm to human health and/or the
environment, the product must be disposed on in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste
disposal in your area.
2
EN
MANUAL ELDES ESIM364 V1.6
Contents
1. GENERAL INFORMATION..........................................................................................................................................................6
1.1.Functionality.......................................................................................................................................................................................................6
1.2. Compatible Device Overview............................................................................................................................................................................6
1.3. Default Parameters & Ways of Parameter Configuration............................................................................................................................6
2. Technical Specifications........................................................................................................................................................14
2.1. Electrical & Mechanical Characteristics........................................................................................................................................................14
2.2. Main Unit, LED & Connector Functionality...................................................................................................................................................15
2.3. Wiring Diagrams...............................................................................................................................................................................................16
3.INSTALLATION........................................................................................................................................................................22
4. GENERAL OPERATIONAL DESCRIPTION................................................................................................................................ 26
5. CONFIGURATION METHODS...................................................................................................................................................27
5.1. SMS Text Messages..........................................................................................................................................................................................27
5.2. EKB2 LCD Keypad.............................................................................................................................................................................................27
5.3. EKB3/EKB3W LED Keypad..............................................................................................................................................................................27
5.4. ELDES Configuration Tool Software............................................................................................................................................................. 28
6. SMS PASSWORD AND INSTALLER CODE.................................................................................................................................33
7. SYSTEM LANGUAGE............................................................................................................................................................... 34
8. USER PHONE NUMBERS.........................................................................................................................................................35
8.1. User Phone Number Names.......................................................................................................................................................................... 36
8.2. System Control from any Phone Number.................................................................................................................................................... 36
9. DATE AND TIME...................................................................................................................................................................... 38
9.1. Automatic Date and Time Synchronization................................................................................................................................................ 38
10. MASTER AND USER CODES ................................................................................................................................................... 39
10.1. Master and User Code Names....................................................................................................................................................................... 41
11. iBUTTON KEYS....................................................................................................................................................................... 42
11.1. Adding and Removing iButton Keys............................................................................................................................................................. 42
11.2. iButton Key Names.......................................................................................................................................................................................... 44
12. ARMING AND DISARMING...................................................................................................................................................... 45
12.1. Free of Charge Phone Call.............................................................................................................................................................................. 45
12.2. SMS Text Message.......................................................................................................................................................................................... 46
12.3. EKB2 Keypad and User/Master Code........................................................................................................................................................... 47
12.4. EKB3 Keypad and User/Master Code........................................................................................................................................................... 49
12.5. EKB3W Keypad and User/Master Code ....................................................................................................................................................... 50
12.6. iButton Key........................................................................................................................................................................................................52
12.7. EWK1/EWK2 Wireless Keyfob........................................................................................................................................................................53
12.8. Arm-Disarm by Zone........................................................................................................................................................................................53
12.9. Disabling and Enabling Arm/Disarm Notifications.................................................................................................................................... 54
13. EXIT AND ENTRY DELAY.........................................................................................................................................................56
14.ZONES..................................................................................................................................................................................... 58
14.1. Zone Numbering.............................................................................................................................................................................................. 58
14.2. Zone Expansion............................................................................................................................................................................................... 58
14.3. 6-Zone Mode.................................................................................................................................................................................................... 58
14.4. ATZ (Advanced Technology Zone) Mode..................................................................................................................................................... 59
14.5. Zone Type Definitions.................................................................................................................................................................................... 60
14.6. Zone Attributes................................................................................................................................................................................................61
14.7. Bypassing and Activating Zones.................................................................................................................................................................. 63
14.8. Zone Names..................................................................................................................................................................................................... 64
14.9. Disabling and Enabling Zones....................................................................................................................................................................... 65
15. STAY MODE............................................................................................................................................................................. 66
16.TAMPERS.................................................................................................................................................................................67
16.1. Tamper Names................................................................................................................................................................................................. 68
17. ALARM INDICATIONS AND NOTIFICATIONS.......................................................................................................................... 69
17.1. Enabling and Disabling Alarm Notifications................................................................................................................................................ 70
17.2. Audio Files.........................................................................................................................................................................................................72
18. PROGRAMMABLE (PGM) OUTPUTS........................................................................................................................................73
18.1. PGM Output Numbering..................................................................................................................................................................................73
18.2. PGM Output Expansion....................................................................................................................................................................................73
18.3. PGM Output Names..........................................................................................................................................................................................74
18.4. Turning PGM Outputs ON and OFF.................................................................................................................................................................74
18.5. PGM Output Control by Event and Scheduler............................................................................................................................................. 76
18.6. Wireless PGM Output Type Definitions.........................................................................................................................................................77
MANUAL ELDES ESIM364 V1.6
EN
3
19. WIRELESS DEVICES................................................................................................................................................................ 78
19.1. Binding, Removing and Replacing Wireless Devicess............................................................................................................................... 78
19.2. Wireless Device Information and Signal Status Monitoring..................................................................................................................... 79
19.3. Disabling and Enabling Siren if Wireless Signal is Lost............................................................................................................................. 81
20.SIREN/BELL............................................................................................................................................................................ 82
20.1. BELL Output Status Monitoring.................................................................................................................................................................... 83
20.2. Bell Squawk...................................................................................................................................................................................................... 84
20.3. Bell Squawk in Stay Mode.............................................................................................................................................................................. 84
20.4. Indication by EWS2 Indicators....................................................................................................................................................................... 86
20.5. Indication by EWS3 Indicators....................................................................................................................................................................... 86
20.6. EWF1 Interconnection.................................................................................................................................................................................... 87
21. BACKUP BATTERY, MAINS POWER SUPPLY STATUS MONITORING AND MEMORY.............................................................. 88
22. GSM CONNECTION AND ANTENNA STATUS MONITORING................................................................................................... 92
23.PARTITIONS........................................................................................................................................................................... 94
23.1. Zone Partition
23.2. User Phone Number Partition....................................................................................................................................................................... 94
23.3. Keypad Partition and Keypad Partition Switch........................................................................................................................................... 95
23.4. User/Master Code Partition......................................................................................................................................................................... 96
23.5. iButton Key Partition...................................................................................................................................................................................... 97
23.6. EWK1/EWK2 Wireless Keyfob Partition ...................................................................................................................................................... 97
24. TEMPERATURE SENSORS...................................................................................................................................................... 98
24.1. Adding, Removing and Replacing Temperature Sensors......................................................................................................................... 98
24.2. Primary and Secondary Temperature Sensors........................................................................................................................................... 99
24.3. Setting Up MIN and MAX Temperature Boundaries. Temperature Info SMS...................................................................................... 100
24.4. Temperature Sensor Names........................................................................................................................................................................ 101
25. REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION................................................................................................. 102
26. SYSTEM INFORMATION. INFO SMS...................................................................................................................................... 103
26.1. Periodic Info SMS........................................................................................................................................................................................... 103
27. SYSTEM NOTIFICATIONS..................................................................................................................................................... 105
27.1. SMSC (Short Message Service Center) Phone Number........................................................................................................................... 113
28. EVENT AND ALARM LOG.......................................................................................................................................................114
29. INDICATION OF SYSTEM FAULTS..........................................................................................................................................115
30. MONITORING STATION..........................................................................................................................................................117
30.1. Data Messages – Events............................................................................................................................................................................... 118
30.2.Communication.............................................................................................................................................................................................. 124
31. DUAL SIM MANAGEMENT.....................................................................................................................................................135
31.1. Disabled Mode............................................................................................................................................................................................... 135
31.2. Automatic Mode............................................................................................................................................................................................ 135
31.3. Manual Mode.................................................................................................................................................................................................. 137
32. ELDES WIRED DEVICES........................................................................................................................................................ 139
32.1. RS485 Interface............................................................................................................................................................................................ 139
32.2. Modules Interface......................................................................................................................................................................................... 157
33. ELDES WIRELESS DEVICES...................................................................................................................................................162
33.1. EKB3W - Wireless LED Keypad.................................................................................................................................................................... 162
33.2. EW1 - Wireless Zone & PGM Output Expansion Module......................................................................................................................... 166
33.3. EWP1 – Wireless Motion Detector.............................................................................................................................................................. 167
33.4. EWD1 – Wireless Magnetic Door Contact.................................................................................................................................................. 169
33.5. EWK1 - Wireless Keyfob................................................................................................................................................................................171
33.6. EWS1 – Wireless Indoor Siren...................................................................................................................................................................... 174
33.7. EWS2 – Wireless Outdoor Siren................................................................................................................................................................... 176
33.8. EW1B - Battery-Powered Wireless Zone & PGM Output Expansion Module...................................................................................... 179
33.9. EWF1 - Wireless Smoke Detector............................................................................................................................................................... 181
33.10.EWK2/EWK2A - Wireless Keyfob................................................................................................................................................................ 186
33.11.EWD2 - Wireless Door Contact/Shock Sensor/Water Sensor................................................................................................................ 189
33.12.EWS3 - Wireless Indoor Siren...................................................................................................................................................................... 194
34. SERVICE MODE..................................................................................................................................................................... 198
35. REMOTE SYSTEM RESTART................................................................................................................................................. 198
36. EN 50131-1 GRADE 3........................................................................................................................................................... 199
37. SMART SECURITY................................................................................................................................................................ 200
38. TECHNICAL SUPPORT ......................................................................................................................................................... 201
38.1.Troubleshooting............................................................................................................................................................................................ 201
38.2. Restoring Default Parameters.................................................................................................................................................................... 201
38.3. Updating the Firmware via USB Cable Locally......................................................................................................................................... 201
38.4. Updating Firmware via GPRS Connection Remotely............................................................................................................................... 202
38.5. Frequently Asked Questions....................................................................................................................................................................... 202
39. RELATED PRODUCTS........................................................................................................................................................... 204
4
EN
MANUAL ELDES ESIM364 V1.6
Limited Liability
The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against such
events.
“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system.
“ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any of the
cellular providers therefore is not responsible for the quality of cellular service.
Manufacturer Warranty
The system carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been
purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the manual
and within specified operating conditions. Receipt must be kept as a proof of purchase date.
The warranty is voided if the system has been exposed to mechanical impact, chemicals, high humidity, fluids, corrosive and hazardous
environments or other force majeure factors.
Package Content
1. ESIM364..................................................... qty. 1
2. Microphone.................................................qty.1
3. SMA antenna............................................. qty. 2
4. Buzzer......................................................... qty. 1
5. Back-up battery connection wire.......... qty. 1
6. User manual............................................... qty. 1
7. Resistors 5,6kΩ.......................................qty. 12
8. Resistors 3,3kΩ.........................................qty. 6
9. Plastic standoffs.......................................qty. 4
About Installation Manual
This document describes detailed installation and operation process of alarm system ESIM364. It is very important to read the installation
manual before starting to use the system.
Copyright © “ELDES UAB”, 2014. All rights reserved
It is not allowed to copy and distribute information in this document or pass to a third party without advanced written authorization by “ELDES
UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products without a warning. Hereby, “ELDES UAB”
declares that this GSM alarm and management system ESIM364 is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
15.105 statement (for digital devices)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must
not be located or operating in conjunction with any other antenna or transmitter..
MANUAL ELDES ESIM364 V1.6
EN
5
1.GENERAL INFORMATION
1.1. Functionality
ESIM364 – micro-controller based alarm system for houses, cottages, country homes, garages and other buildings, also capable of managing electrical appliances via cellular GSM/GPRS network. It can also be used as Intercom system.
Examples of using the system:
• Property security.
• Alarm switch.
• Thermostat, heating and air-conditioner control, temperature monitoring.
• Lighting, garden watering, water pump and other electrical equipment control via SMS text messages.
• Remote listening to what is happening in the secured area.
• Mains power status notification by SMS text message.
• Two-way intercom device via GSM network.
1.2. Compatible Device Overview
Wired Devices
Description
Device
EKB2
LCD keypad
4*
Max. Connectable Devices
EKB3
LED keypad
4*
EA1
EA2
EPGM1
ELAN3-ALARM
EPGM8
Audio output module with 3,5mm jack
Audio amplifier module 1W 8Ω
16 zone and 2 PGM output expansion module
Ethernet communicator
8 PGM output expansion module
1**
1**
2
1
1**
Device
EW1
EW1B
EWP1
EWD1
EWD2
EWK1****
EWK2****
EWS1
EWK2A***
EWS2
EKB3W
EWF1
EWS3
Wireless Devices
Description
Wireless 2 zone and 2 PGM output expansion module
Battery-powered wireless 2 zone and 2 PGM output expansion module
Wireless motion detector
Wireless magnetic door contact
Wireless magnetic door contact/shock sensor/water sensor
Wireless keyfob with 4 buttons
Wireless keyfob with 4 buttons
Wireless indoor siren
Wireless keyfob with 1 button
Wireless outdoor siren
Wireless LED keypad
Wireless smoke detector
Wireless indoor siren
Max. Connectable Devices
32***
32***
32***
32***
32***
5***
5***
32***
5***
32***
4***
32***
32***
* - A mixed combination of EKB2 and EKB3 keypads is supported. The combination can consist of up to 4 keypads in total.
** - Only 1 of these modules can be connected at a time if the module slots are implemented in ESIM364 unit.
*** - A mixed combination of wireless devices is supported. The combination can consist of up to 32 wireless devices in total.
**** - A mixed combination of EWK1 and EWK2 keyfobs is supported. The combination can consist of up to 5 keyfobs in total.
1.3. Default Parameters & Ways of Parameter Configuration
Main Settings
Parameter
Default Value
User 1... 10 name
User 1... 10 phone number
User 1... 10 partition
User 1...10 - call in case of alarm
Allow control from any phone number
SMS password
SMS language
Partition 1 name
Partition 2 name
Partition 3 name
Partition 4 name
N/A
N/A
Partition 1
Enabled
Disabled
0000
Depends on the firmware
PART1
PART2
PART3
PART4
6
EN
Configurable by:
EKB3/
SMS EKB2
EKB3W













Configuration
Tool










MANUAL ELDES ESIM364 V1.6
Partition 1... 4 exit delay
GSM signal loss indication - delay
GSM signal loss indication – activate output
Dual SIM management – SIM card switch
Dual SIM management – try to find operator for a
maximum of
Dual SIM management – send SMS/call via
15 seconds
180 seconds
N/A
Disabled







3 time (s)

Currently in use SIM

Main Settings
Parameter
Default Value
Installer's code
Duress code
SGS code
Passwords/codes format
Prompt additionally for master code when configuring via keypad/software
Master code
Master code name
1470
N/A
N/A
4-digit
Passwords/Codes
Configurable by:
EKB3/
SMS EKB2
EKB3W
Configuration
Tool




















Disabled





Main power loss
1111
N/A
Partition 1, Partition 2, Partition 3, Partition 4
N/A
N/A
Partition 1
Faults
Enabled
Low battery
Enabled

Battery dead or missing
Enabled

Battery failed
Enabled

Siren failed
Enabled

Tamper alarm
Enabled

Date/time not set
Enabled

GSM connection failed
Enabled

GSM antenna failed
Enabled

Wireless antenna failed
Enabled

Keypad lost
Enabled
Master code partition
User code 2... 30
User code 2... 30 name
User code 2... 30 partition


Notifications
System armed – User 1... 10
Enabled



System armed – SMS delivery report
Enabled



System disarmed – User 1... 10
Enabled



System disarmed – SMS delivery report
Enabled



General alarm – User 1... 10
Enabled



General alarm – SMS delivery report
Enabled



Main power loss/restore – User 1... 10
Enabled



Main power loss/restore – SMS delivery report
Enabled



Battery failed – User 1... 10
Enabled



Battery failed – SMS delivery report
Enabled



Battery dead or missing – User 1... 10
Enabled



Battery dead or missing – SMS delivery report
Enabled



Low battery – User 1... 10
Enabled



Low battery – SMS delivery report
Enabled



Siren fail/restore – User 1... 10
Disabled



Siren fail/restore – SMS delivery report
Disabled



Date/time not set – User 1... 10
Disabled



Date/time not set – SMS delivery report
Disabled



GSM connection failed – User 1... 10
Disabled



GSM connection failed – SMS delivery report
Disabled



GSM antenna fail/restore – User 1... 10
Disabled



MANUAL ELDES ESIM364 V1.6
EN
7
GSM antenna fail/restore – SMS delivery report
Disabled



Tamper alarm/restore – User 1... 10
Enabled



Tamper alarm/restore – SMS delivery report
Enabled



Keypad loss/restore – User 1... 10
Enabled



Keypad loss/restore – SMS delivery report
Enabled



Temperature info – User 1... 10
Enabled



Temperature info – SMS delivery report
Enabled



System started – User 1... 10
Enabled



System started – SMS delivery report
Enabled



Periodical info – User 1... 10
Enabled



Periodical info – SMS delivery report
Enabled



Wireless signal loss – User 1... 10
Enabled



Wireless signal loss – SMS delivery report
Enabled



Unable to arm – User 1... 10
Enabled



Unable to arm – SMS delivery report
Enabled






Send to all users simultaneously – all notifications Disabled
Time Synchronization
Time synchronization over GSM network
Disabled
Phone number of the currently inserted SIM card
N/A
Synchronization frequency
30 days



Event Log
Event log
Enabled

Zones


Configurable by:
EKB3/
SMS EKB2
EKB3W
Parameter
Default Value
Z1... Z6 zone name
Z1 type
Z2... Z6 type
Z1... Z6 delay, ms
Z1... Z6 – Stay
Z1... Z6 – Force
On Board
Zone1... Zone6
Delay
Instant
800 milliseconds
Disabled
Disabled
Z1... Z6 tamer name
Tamper1... Tamper6
Delay-type zone – entry delay
Z1... Z6 partition
Z1... Z6 – Shared
Z1... Z6 – audio track
Delay becomes Instant in STAY mode
Chime
ATZ mode
Arm-disarm by zone No1... No4
Zone connection type
Zone name
Status
Type
Delay, ms
Stay
Force
Tamper name
Delay-type zone – entry delay
Partition
Shared
Audio track
15 seconds
Partition 1
Disabled
N/A
Disabled
Enabled
Disabled
N/A
Type 1
EPGM1 Module
Zone X
Enabled
Instant
800 milliseconds
Disabled
Disabled
Tamper X
15 seconds
Partition 1
Disabled
N/A
Zone name
Zone X

Status
Enabled



Configuration
Tool































































Wireless Devices
8
EN


MANUAL ELDES ESIM364 V1.6
Stay
Depends on the connected wireless device model
Disabled
Force
Disabled
Tamper name
Tamper X
Delay-type zone – entry delay
Type









15 seconds



Partition
Partition 1



Shared
Disabled
Audio track
N/A



Keypads
Zone name
Zone X

Status
Disabled

Type




Instant



Stay
Disabled



Force
Disabled



Tamper name
Tamper X
Delay-type zone – entry delay
15 seconds



Partition
Partition 1



Shared
Disabled
Audio track
N/A



Virtual Zones
Zone name
Zone X
Status
Disabled


Type
Instant


Force
Disabled


Delay-type zone – entry delay
15 seconds


Partition
Partition 1


Shared
Disabled


PGM Outputs
Parameter
C1... C4 output name
Status
Using module EPGM8
Output name
Status
Output name
Type
Status
Default Value
On Board
Controll1... Controll4
Turned OFF
Disabled
EPGM1 Module
ControllX
Turned OFF
Wireless Devices
ControllX




Parameter
Default Value
MS mode
Account
GSM & SMS – attempts
GSM & SMS – tel. number 1... 3
PSTN – treat PSTN call as user call
PSTN – attempts
PSTN – tel. number 1... 3
CSD – attempts
CSD – tel. number 1... 5
IP – IP attempts
Disabled
9999
5
N/A
Disable
5
N/A
5
N/A
3
Management













Configurable by:
EKB3/
SMS EKB2
EKB3W

Configuration
Tool



Depends on the connected wireless
device model

Turned OFF
MS Settings
MANUAL ELDES ESIM364 V1.6
Configurable by:
EKB3/
SMS EKB2
EKB3W



















Configuration
Tool










EN
9
IP – test period
180 seconds



IP – protocol
IP – unit ID
IP – communication protocol
IP – server IP
IP – server port
Communication - primary
Communication – backup 1... 5
Delay after last communication attempt
SIA IP protocol settings - encryption
SIA IP protocol settings – encryption key
SIA IP protocol settings – account prefix
SIA IP protocol settings – receiver number
SIA IP protocol settings – Contact ID ping
SIA IP protocol settings – data message

UDP
0000
EGR100

0.0.0.0

20000
GPRS network
N/A
600 seconds
Disabled
0000
N/A
N/A
Disabled
Event: 1602, partition: 01, user/zone: 000
Data Messages
130
Enabled
301
Enabled
401
Enabled
602
Enabled
309
Enabled
311
Enabled
144
Enabled
146
Enabled
602
Enabled
900
Enabled
133
Enabled
110
Enabled
302
Enabled
158
Enabled
159
Enabled
381
Enabled
121
Enabled
463
Enabled
456
Enabled
321
Disabled
626
Enabled
358
Enabled
359










































































Burglary alarm/restore – code
Burglary alarm/restore – status
Main power loss/restore – code
Main power loss/restore – status
Armed/disarmed by user – code
Armed/disarmed by user – status
Test event – code
Test event – status
Battery failed – code
Battery failed – status
Battery dead or missing – code
Battery dead or missing – status
Tamper alarm/restore – code
Tamper alarm/restore – status
Silent zone alarm/restore – code
Silent zone alarm/restore – status
Kronos ping – code
Kronos ping – status
System started – code
System started – status
24H zone alarm/restore – code
24H zone alarm/restore – status
Fire zone alarm/restore – code
Fire zone alarm/restore – status
Low battery – code
Low battery – status
Temperature exceeded – code
Temperature exceeded – status
Temperature fallen – code
Temperature fallen – status
Wireless signal loss/restore – code
Wireless signal loss/restore – status
Disarmed by user (duress code) – code
Disarmed by user (duress code) – status
Armed/disarmed by user (SGS code) – code
Armed by user (SGS code) – status
Armed/disarmed in STAY mode – code
Armed/disarmed in STAY mode – status
Siren fail/restore – code
Siren fail/restore – status
Date/time not set – code
Date/time not set – status
GSM connection failed – code
GSM connection failed – status
GSM antenna fail/restore – code
10
EN













































MANUAL ELDES ESIM364 V1.6
GSM antenna fail/restore – status
System shutdown – code
System shutdown – status
Keypad fail/restore – code
Keypad fail/restore – status
GPRS connection lost – code
GPRS connection lost – status
Zone bypass – code
Zone bypass – status
Disabled
414
Enabled
330
Enabled
354
Enabled
570
Enabled
Control / Scheduler
Parameter
Default Value
PGM output control 1... 16
Scheduler 1... 16
Additional conditions
Disabled
Disabled
Disabled
Peripheral Devices
Parameter
Default Value
Keypad 1... 4 partition
Partition 1
Show armed status in keypad
Disabled
Keypad partition switch
Disabled
EKB3 mode
2 partitions
Wireless keypads - partition
Partition 1
Wireless keypads – backlight timeout
10 seconds
Wireless keypads – bell
Disabled
Keypads










Configurable by:
EKB3/
SMS EKB2
EKB3W
Configurable by:
EKB3/
SMS EKB2
EKB3W















Configuration
Tool



Configuration
Tool







Siren
EWS2 LED
Enabled
Bell squawk
Disabled
Activate siren if wireless device is lost
Disabled
EWS3 fire alarm LED
Disabled
EWS3 alarm LED
Disabled
Bell squawk enabled if arming in STAY mode
Disabled
Temperature sensor 1... 8 name
N/A

Temperature sensor 1... 8 min. temperature
0
Temperature sensor 1... 8 max. temperature























0




Primary
No.1

Secondary
No.2







iButton key name
N/A
iButton key partition
Partition 1
Allow adding new iButton keys
Disabled








Temperature Sensors
iButton Keys
System
Configurable by:
EKB3/
SMS EKB2
EKB3W
Parameter
Default Value
Mains power loss delay
30 seconds



Mains power restore delay
120 seconds
1 minute



Alarm duration


Wireless channel
Depends on firmware
Periodic test
Every 1 day at 11:00

Microphone level
12
Speaker level
85



Management
MANUAL ELDES ESIM364 V1.6

Configuration
Tool






EN
11
Service mode
Disabled




Smart Security
Smart Security
Disabled

Server address
ss.eldes.lt

Port
8082

Ping period
180 seconds

Time zone
N/A

Communication
Via GPRS network

GPRS Settings
SIM1... SIM2 APN
N/A

SIM1... SIM2 user name
N/A

SIM1... SIM2 password
N/A

DNS1
N/A

DNS2
N/A

12
EN









MANUAL ELDES ESIM364 V1.6
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Electrical & Mechanical Characteristics
Main power supply
Current in standby without external sensors and keypad
Recommended backup battery voltage, capacity
Recommended backup battery type
Backup battery charge current
Backup battery charge duration
Gsm modem frequency
Cable type for GSM/GPRS antenna connection
Number of zones on-board
Nominal zone resistance
Number of PGM outputs on-board
16-24V 50 Hz ~1.5A max / 18-24V
Up to 80mA
12V; 1,3-7 Ah
Lead-Acid
Up to 500mA
Up to 30 hours for 7Ah battery
850/900/1800/1900MHz
Shielded
6 (ATZ mode: 12)
5,6kΩ (ATZ Mode: 5,6kΩ and 3,3kΩ)
4
1R
On-board PGM output circuit
Maximum commuting on-board PGM output values
BELL: Siren output when activated
BELL: Maximum siren output current
BELL: Maximum cable length for siren connection
BELL: Cable type for siren connection
AUX: Auxiliary equipment power supply voltage
AUX: Maximum accumulative current of auxiliary equipment
AUX: Maximum cable length for auxiliary equipment connection
AUX: Cable type for auxiliary equipment connection
BUZ: Maximum current of mini buzzer
BUZ: Power supply voltage of buzzer
BUZ: Cable type for mini buzzer connection
Supported temperature sensor model
Maximum supported number of temperature sensors
DATA: Maximum cable length for 1-Wire communication
DATA: Cable type for 1-Wire communication
Supported iButton key model
Maximum supported number of iButton keys
Maximum supported number of keypads
Y/G: Maximum cable length for RS485 communication
Y/G: Cable type for RS485 communication
MIC: Maximum cable length for microphone connection
MIC: Cable type for microphone connection
Wireless transmitter-receiver frequency
Wireless communication range
Maximum supported number of wireless devices
Event log size
Maximum supported number of zones
Maximum supported number of PGM outputs
Cable type for zone and PGM output connection
Communications
Supported protocols
Dimensions
Operating temperature range
Humidity
MANUAL ELDES ESIM364 V1.6
OUT
1,5A max
Open Collector Output.
Output is pulled to COM
when turned ON.
4 x Voltage – 30V; current – 500mA.
Connected to COM
1A
Up to 100 meters
Unshielded
13,8V DC
1,1A
Up to 100 meters
Unshielded
150mA
5V DC
Unshielded
Maxim®/Dallas® DS18S20, DS18B20
8
Up to 30 meters
Unshielded
Maxim®/Dallas® DS1990A
16
4 x EKB2 / EKB3
Up to 100 meters
Unshielded
Up to 2 meters
Unshielded
868 Mhz (EU version) / 915 Mhz (US version)
Up to 30m in premises; up to 150m in open areas
32
500 events
76
76
Unshielded
SMS, Voice calls, GPRS network, RS485, CSD, PSTN, Ethernet via
ELAN3-ALARM
Ademco Contact ID, EGR100, Kronos, Cortex SMS, SIA IP
140x100x18mm
-20...+55 °C
0-90% RH @ 0... +40 °C (non-condensing)
EN
13
2.2. Main Unit, LED & Connector Functionality
SIM CARD2
OPEN
DEF
1
OPEN
S TA T
C4
C3
C2
C1
SIM CARD1
GSM/GPRS ANT
G SM
MO DE M
3A
FUSE F1
PRG
USB
MODULES
TIP RING
Slots for EA1, EA2 or EPGM8 module
W-LESS ANT
C 4C 3
MODULES*
NE TW
Main Unit Functionality
GSM MODEM
GSM network 850/900/1800/1900MHz
modem
SIM CARD1
Primary SIM card slot / holder
SIM CARD2
Secondary SIM card slot / holder
DEF
Pins for restoring default settings
USB
Mini USB port
FUSE F1
3A fuse
W-LESS ANT
Wireless antenna SMA type connector
GSM/GPRS ANT
GSM/GPRS antenna SMA type connector
AK U +
AK U -
AC /DC
AC /DC
AUX+
AUXBELL+
BELL-
CO M
G
Y
C2
C1
BU Z +
BU Z MIC +
M IC +5V
DAT A
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
LED Functionality
NETW
GSM network signal strength
C1
PGM output C1 status - ON/OFF
C2
PGM output C2 status - ON/OFF
C3
PGM output C3 status - ON/OFF
C4
PGM output C4 status - ON/OFF
STAT
Micro-controller status
NETW indication
OFF
Flashing every 3 sec.
Flashing every 1 sec.
Flashing several times per sec.
Steady ON
GSM signal strength
No GSM signal
Poor
Medium
Good
Excellent
Connector Functionality
TIP*
PSTN (landline) terminal
RING*
PSTN (landline) terminal
DATA
1-Wire interface for iButton key & temperature sensor connection
+5V
Temperature sensor power supply terminal (+5V)
MICMicrophone negative terminal
MIC+
Microphone positive terminal
BUZBuzzer negative terminal
BUZ+
Buzzer positive terminal
C1 - C4
PGM output terminals
Z1 - Z6
Security zone terminals
Y
RS485 interface CLOCK terminal (yellow wire)
G
RS485 interface DATA terminal (green wire)
COM
Common return terminal
BELLSiren negative terminal
BELL+
Siren positive terminal
AUXNegative power supply terminal for auxiliary equipment
AUX+
Positive power supply terminal for auxiliary equipment
AC/DC
Main power supply terminals
AKUBackup battery negative terminal
AKU+
Backup battery positive terminal
* - Optional, implementable on request in advance
14
EN
MANUAL ELDES ESIM364 V1.6
2.3. Wiring Diagrams
2.3.1.General Wiring
2
AKU+
AKU-
Backup Battery
12V 1.3-7Ah
AC /DC
AC /DC
AUX+
AUXBELL+
BELLCO M
G
Y
C2
C1
BUZ+
BUZMIC +
MIC +5V
DATA
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
Metal cabinet
PE terminal
Fuse 500 mA
~16-24V
~230V 50Hz
Z6
Z5
Z4
Z3
Z2
Z1
BUZ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
MIC
SIREN/BELL
EPGM1
1A max.
iButton®
key reader
Relay
module
EKB3
Temperature sensor
EKB2
ELAN3-ALARM
2.3.2. Zone Connection Types
Type 1 Example of 4-wire smoke detector wiring
AUX+
C1
COM
Z1
3
5,6 kΩ
6-Zone mode: Normally open contact
with 5,6KΩ end-ofline resistor.
COM
GND
NO
+Vin
Example of magnetic door contact wiring
6-Zone mode: Normally closed contact
with 5,6KΩ end-ofline resistor
COM
Z1
4
5,6 kΩ
Type 2
COM
NC
Magnet
NOTE: Based on the example given, in the event of an alarm, the smoke detector could be reset by turining OFF and ON the PGM
output C1. For more details, please refer to 18.4. Turning PGM Outputs ON and OFF.
MANUAL ELDES ESIM364 V1.6
EN
15
NOTE: The system does NOT support 2-wire smoke detectors.
Type 3
AUX+
AUX-
COM
Z1
5
Example of motion detector wiring
6-Zone mode: Tamper
and 5,6KΩ end-of-line
resistor and 3,3KΩ
end-of-line resistor
with normally closed
contact.
COM
5,6 kΩ
3,3 kΩ
GND
NC
+Vin
TAMP
Type 4
AUX+
AUX-
3,3 kΩ
ATZ mode: 5,6KΩ
end-of-line resistor
and normally closed
contact with 3,3KΩ
end-of-line resistor
and normally closed
contact
5,6 kΩ
COM
Z1
6
Example of magnetic door contact (Z1) and glass break sensor (Z7) wiring
NC
COM
Magnet
Type 5
GND
NC
+Vin
Example of motion detector (Z1) and magnetic door contact (Z7) wiring
AUX+
AUX-
COM
Z1
7
COM
ATZ mode: Tamper,
5,6KΩ end-of-line
resistor, 5,6KΩ
end-of-line resistor
with normally closed
contact and 3,3KΩ
end-of-line resistor
with normally closed
contact.
5,6 kΩ
5,6 kΩ
3,3 kΩ
NC
COM
Magnet
COM
NC
TAMP
GND
+Vin
See also 14.3. 6-Zone Mode and 14.4. ATZ (Advanced Technology Zone) Mode.
16
EN
MANUAL ELDES ESIM364 V1.6
2.3.3. Siren
Piezo siren
BELL+
BELL-
8
1 Connect positive siren wire (red) to BELL+ terminal.
2 Connect negative siren wire (black) to BELLterminal.
BLACK SIREN/BELL
1A max.
RED +
Self-contained siren
BELL+
BELLCOM
9
1 Connect negative GND siren wire to COM terminal.
2Controlling BELL siren wire must be connected
to BELL- terminal.
GND
3 Connect positive +12V siren wire to BELL+ terminal.
BELL
SIREN/BELL
1A max.
+12V
Siren status monitoring
BELL+
BELL-
10
BLACK SIREN/BELL
1A max.
3,3kΩ
3,3kΩ
By default, the system monitors siren status and
indicates system fault on the keypad if the siren
is broken/disconnected. However, this feature
requires a pair of parallelly connected resistors of
3,3kΩ nominal across BELL+ and BELL- terminals.
RED +
BELL+
BELL-
11
No siren status monitoring
If the siren status monitoring feature is not required, do not connect any resistor in parallel and
disable siren fault indication on the keypad (see 29.
INDICATION OF SYSTEM FAULTS).
BLACK SIREN/BELL
1A max.
RED +
See also 20. SIREN/BELL.
NOTE: BELL- is the commuted terminal intended for siren control.
NOTE: Siren status monitoring feature supervises the resistance across BELL+ and BELL- terminals. The resistance must be ranging from
1kΩ through 3,3kΩ, otherwise the system will indicate system fault. In order to view the siren resistance value, please refer to Diagnostic
Management feature available on ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
EN
17
2.3.4. iButton Key Reader and Buzzer
Supported iButton key model: Maxim/Dallas
DS1990A
BUZ+
BUZ-
COM
DATA
12
-
The iButton key reader can be installed with buzzer
or separately. The buzzer is intended for audio indication of exit/entry delay countdown providing
short beeps.
+ BUZZER
1 Connect iButton key reader terminal wires to
1-Wire interface: COM and DATA terminals respectively.
2 Connect buzzer‘s negative terminal wire to BUZand positive terminal wire to BUZ+.
3 Additionally, a LED indicator for visual indication
can be installed in parallel to buzzer or instead.
Connect LED anode terminal to BUZ- and cathode to BUZ+.
iButton
key reader
DS1990A
NOTE: The installation of buzzer is not necessary if EKB2/EKB3 keypad is used.
ATENTION: The cable length for connection to 1-Wire interface can be up to 30 meters max.
2.3.5. Temperature Sensor and iButton Key Reader
Supported iButton key model: Maxim/Dallas DS1990A
Supported temperature sensor model: Maxim/Dallas DS18S20, DS18B20
TEMPERATURE
SENSOR
DS18S20,
DS18B20
DATA
GND
+5V
DS18S20, DS18B20
TEMPERATURE SENSOR
GND
1 Connect temperature sensor GND, DATA, +5V
terminals to 1-Wire interface: COM, DATA and
+5V terminals respectively.
2 When connecting iButton key reader in parallel
to temperature sensor, connect iButton key reader terminal wires to COM and DATA terminals
respectively.
+5V
DATA
COM
+5V
DATA
COM
13
ATENTION: The cable length for connection to
1-Wire interface can be up to 30 meters max.
GND
+5V
DATA
DATA +5V
iButton
key reader
DS1990A
2.3.6. Relay Finder 40.61.9.12 with Terminal Socket 95.85.3 to PGM Output
AUX+
C1
14
1 Wire up relay A1 terminal to PGM output Cx and
A2 terminal to AUX+.
2 In addition, connect LED indicator‘s anode terminal to relay A2 terminal and cathode to A1
terminal.
LED
COIL
A2
A1
RELAY
18
EN
MANUAL ELDES ESIM364 V1.6
2.3.7. RS485
Serial Wiring Method
ESIM364
a
EKB2/EKB3
b
EKB2/EKB3
c
EKB2/EKB3
d
EKB2/EKB3
e
EPGM1
Max. cable length: a+b+c+d+e+f+g= up to 100 meters
f
EPGM1
g
ELAN3-ALARM
NOTE: If necessary, the RS485 devices can be powered from an external 12-14V DC power supply instead of AUX+ and AUX- terminals
ATTENTION: The cable length must not exceed 100 meters in total.
ATTENTION: When wiring more than 1 keypad and/or EPGM1 module, please ensure that the set address of each keypad and/or EPGM1
module is different.
NOTE: You may connect only 1 EKB2/EKB3 keypad or a mixed combination of EKB2 and EKB3 keypads. The combination can consist of
up to 4 keypads in total.
For more details on RS485 device installation, please refer to 32.1. RS485 Interface
MANUAL ELDES ESIM364 V1.6
EN
19
Parallel Wiring Method
ESIM364
Max. cable length: up to 100 meters
EPGM1
EPGM1
EKB2/EKB3
EKB2/EKB3
EKB2/EKB3
ELAN3-ALARM
NOTE: If necessary, the RS485 devices can be powered from an external 12-14V DC power supply instead of AUX+ and AUX- terminals
ATTENTION: The cable between ESIM364 and each RS485 device must be of the same length and can NOT exceed 100 meters.
ATTENTION: When wiring more than 1 keypad and/or EPGM1 module, please ensure that the set address of each keypad and/or EPGM1
module is different.
NOTE: You may connect only 1 EKB2/EKB3 keypad or a mixed combination of EKB2 and EKB3 keypads. The combination can consist of
up to 4 keypads in total.
For more details on RS485 device installation, please refer to 32.1. RS485 Interface
2.3.8. RING/TIP
15
to PSTN
(landline)
ATTENTION: The TIP/RING connectors and PSTN module are NOT
included in a standard ESIM364 alarm system unit. These components
are op­tional and can be implemented on request in advance.
RING
TIP
20
EN
ESIM364
MANUAL ELDES ESIM364 V1.6
3.INSTALLATION
When professional installation, OEM integration or assembly by a third-party is expected, the installation instructions and assembly requirements approved for equipment approval must be provided to the integrators to clearly identify the specific requirements necessary
to maintain RF exposure compliance. The grantee of a transmitter, typically the manufacturer, is responsible for ensuring installers and
integrators have a clear understanding of the compliance requirements by including the required instructions and documentation with
the product and, if necessary, to provide further support to fulfill grantee responsibilities for ensuring compliance. The integrators must
be fully informed of their obligations and verify the resolution of any issues and concerns with each transmitter manufacturer or grantee.
• The system can be installed in a metal or non-flammable cabinet only. For a convenient installation, ME1 metal cabinet is highly recommended. When using a different metal cabinet, it is necessary to ground it.
• For the connection of 230V transformer, use 3x0.75 mm2 1 thread double isolated cable. 230V power supply cables must not be
grouped with low voltage cable group.
• For the connection of auxiliary and BELL outputs, use 2x0.75 mm2 1 thread unshielded cable of up to 100 meters length.
• For the connection of zone/PGM output connectors, use 0.50 mm2 1 thread unshielded cable of up to 100 meters length.
System Installation in ME1 Metal Cabinet
1. ME1 metal cabinet components
16
to AC main power line
Null
blue
PE
Phase
brown
Fuse 1A
Transformer
(Primary voltage: 230V AC,
Secondary voltage: 17V
2,35A)
Tamper switch
to AC/DC terminals
of ESIM364 system
2. Insert the plastic standoffs into the appropriate mounting points and fix the board of ESIM364 on the holders as indicated below.
17
mounting points
MANUAL ELDES ESIM364 V1.6
EN
21
18
7
3. If EPGM1 module is to be installed, please install it in the first place and ESIM364 alarm system afterwards. EPGM1 must be mounted on
the shorter plastic standoffs, while ESIM364 – on the longer ones. The mounting points of EPGM1 module are indicated below.
19
mounting
points
Inserting a SIM card into SIM
CARD1 slot is mandatory as it
is the main SIM card slot, while
using a SIM card in SIM CARD2
slot is optional.
22
EN
MANUAL ELDES ESIM364 V1.6
20
Never install in the following
locations:
• inside the metal cabinet
Recommended installation:
• keep the distance of at least 20
cm or more.
• closer than 20 cm from the
metal surface and/or power
lines
21
Never install in the following
locations:
7
• inside the metal cabinet
• closer than 20 cm from the
metal surface and/or power
lines
Recommended installation:
• face the front side of the
wireless device towards the
antenna
• keep the distance: 0.5 m to 30
m inside the building, 0.5 m to
150 m in open areas
4. Wire up the system according to the wiring diagrams. Install the buzzer closer to iButton key reader in order to hear the exit delay
countdown. A LED indicator can be used in parallel to the buzzer or instead. For a convenient installation, ED1 is highly recommended
(see 2.3 Wiring Diagrams for more details).
5. Disable the PIN code of the SIM card by inserting it into a mobile phone and following the proper menu steps. Ensure that the additional services, such as voice mail, call forwarding, report on missed/busy calls (“call catcher”) are disabled on the SIM card. For
more details on how to disable these services, please contact your GSM operator.
6. Once the PIN code is disabled, place the SIM card into the SIM CARD1 slot of the alarm system. If Dual-SIM feature is to be used, insert
another SIM card into the SIM CARD2 slot. For more details, please refer to 31. DUAL-SIM MANAGEMENT.
MANUAL ELDES ESIM364 V1.6
EN
23
22
24
OPEN
23
26
OPEN
25
7. Connect the GSM/GPRS and wireless antennas and follow the recommendations for the installation:
27
28
GSM/
GPRS
and/or
wireless
antenna
20 cm
or more
GSM/GPRS
antenna
Wireless
antenna
8. If one or more wireless devices are to be bound, follow the recommendations for the installation to achieve the strongest wireless
signal:
29
30
0.5 m to 30 m
inside the building
Wireless
device
0.5 m to 150 m
in open areas
Wireless
device
Wireless
antenna
For more details on how to install the wireless devices, please refer to 33. ELDES WIRELESS DEVICES and RADIO SYSTEM IN­
STALLATION AND SIGNAL PENETRATION manual located at www.eldes.lt/download
9. Power up the system and wait until indicator STAT lights up.
10. The system starts up in less than a minute. Indicator STAT should be flashing indicating successful micro-controller operation.
11. The illuminated indicator NETW indicates that the system successfully registered to GSM network. To find the strongest GSM signal,
place the GSM/GPRS antenna and follow the indications provided by NETW indicator (see 2.3. Main Unit, LED & Connector Functionality).
12. Change the default SMS password (see 6. SMS PASSWORD AND INSTALLER CODE for more details).
13. Set the phone number for User 1 (see 8. USER PHONE NUMBERS for more details).
14. Set system date and time (see 9. DATE AND TIME for more details).
15. Once the system is fully configured, it is ready for use. However, if you fail to receive an SMS reply from the system, please check the
SMSC (Short Message Service Center) phone number. For more details regarding the SMS centre phone number, please refer to 27.1.
SMSC (Short Message Service Center) Phone Number.
16. If it is required to change the batteries for the wireless devices or carry out other system maintenance tasks, please activate the
Service mode. For more detail regarding this mode, please refer to 34. SERVICE MODE.
24
EN
MANUAL ELDES ESIM364 V1.6
ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM profile enabled
are supported. For more details, please contact your GSM operator.
NOTE: The installation of iButton key reader, EKB2/EKB3/EKB3W keypad, EWK1 wireless keyfob is not mandatory. However, it is
recommended to have those devices installed as an emergency switch in case your mobile phone is switched off or missing.
NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insufficient
NOTE:
We advise
youSIM
to choose
the
same GSM
SIM
your system
as formessages.
your mobile phone. This will ensure the fastest,
credit balance
on the
card, the
system
would
failprovider
to makefor
a phone
call or send
most reliable SMS text message delivery service and phone call connection.
NOTE: Even though alarm system ESIM364 installation process is not too complicated, we still recommend to perform it by a person
with basic knowledge in electrical engineering and electronics to avoid any system damage.
4.GENERAL OPERATIONAL DESCRIPTION
When the system is being armed, it will initiate the exit delay countdown intended for the user to leave the secured area. During the countdown period the buzzer will emit short beeps. By default, exit delay duration is 15 seconds. After the countdown is complete, the system
will become armed and lock the configuration by keypad possibility. In case the user does not leave the secured area before the countdown
is complete, the system will will arm in Stay mode if at least 1 zone has Stay attribute enabled. By default, if there is at least 1 violated zone
or tamper, the user will not be able to arm the system until the violated zone or tamper is restored. In case it is required to arm the alarm
system despite the violated zone presence, the violated zone can be bypassed or Force attribute enabled.
After the system is armed and if a zone (depending on type) or tamper is violated, the system will cause an alarm lasting for 1 minute (by
default), During the alarm, the siren/bell will provide an alarm sound along with the buzzers of the keypads. By default, the system will also
makes a phone call and send an SMS text message containing the violated zone or tamper number to a preset user and indicate the violated
zone or tamper number on the keypad. If another zone or tamper is violated or the same one is restored and violated again during the alarm,
the system will act as mentioned previously, but will not extend the alarm time.
After the user enters the secured area, the system will initiate the entry delay countdown intended for system disarming. During the countdown period, the buzzer will emit a steady beep. By default, entry delay duration is 15 seconds. After the user successfully performs the
disarming process, the system will unlock the keypads. If the user does not disarm the system in time, the alarm system will cause an
instant alarm.
NOTE: The alarm will be caused even if a tamper is violated while the system is disarmed.
For more details, please refer to 12. ARMING AND DISARMING.
MANUAL ELDES ESIM364 V1.6
EN
25
5.CONFIGURATION METHODS
!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character
must be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning
and at the end of the SMS text message.
EN50131-1
GRADE 3
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following features:
• All codes and passwords must consist of 6 digits.
• The system must prompt for master (see 10. MASTER AND USER CODES) and installer (see 6. SMS PASSWORD AND INSTALLER CODE) codes when configuring the system by EKB2, EKB3, EKB3W keypad or ELDES Configuration Tool software.
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please
refer to 36. EN 50131-1 GRADE 3
5.1. SMS Text Messages
In order to configure and control the system by SMS text message, send the text command to the ESIM364 system phone
number from one of the preset user phone numbers. The structure of SMS text message consists of 4-digit SMS password
(the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g.
STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in brackets.
SMS
5.2. EKB2 LCD Keypad
The system configuration and control by EKB2 keypad is carried out by navigating throughout the menu section list displayed
on LCD screen. To navigate in the menu path, touch ↓, ↑ keys to select the desired menu section and touch OK key to open the
selected section. To enter a required value, use 0... 9 keys and touch OK key for confirmation or cancel/go one menu section
back by touching ← key. The value can be typed in directly by touching 0... 9 keys while highlighting the desired menu section. EKB2 menu type is “circle”, therefore when the last section in the menu list is selected, you will be brought back to the
beginning of the list after touching the ↓ key. In this installation manual, the menu path is based on the EKB2 menu tree by
starting at home screen view (see 32.1.1.6. EKB2 Menu Tree). The variables are provided in lower-case letters, while a valid
parameter value range is provided in brackets.
EKB2
NOTE: By default, menu section CONFIGURATION is secured with installer code. The default installer code is 1470. NOTE: The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the menu section
icon.
CONFIGURATION is opened. The inactive EKB2 keypads will display
NOTE: The keypad will automatically exit the menu section CONFIGURATION and return to home screen view if 1 minute after the last
key-touch expires.
5.3. EKB3/EKB3W LED Keypad
EKB3/
EKB3W
The system configuration and control by EKB3/EKB3W keypad is carried out by activating the Configuration mode using the
installer code (by default – installer code is 1470) and entering a valid configuration command using the number keys [0]...
[9], [#] key for confirmation and [*] key to clear the characters that have been entered. Alternatively, the user can wait for
10 seconds until the keypad buzzer will provide a long beep indicating that the entered characters have been cleared. When
typing in the characters, the indication of each pressed key is provided by short beep of keypad buzzer and red indicators when
the number keys [0]... [9] are being pressed. Some commands require [STAY], [BYPS], [INST] and [CODE] keys as well. The
structure of a standard configuration command is a combination of digits. The commands, which do not require the Configuration mode being activated, are noted. The variables are provided in lower-case letters, while a valid parameter value range
is provided in brackets.
NOTE: If you have accidentally typed in an unnecessary character (-s), please press [*] key or wait for 10 seconds until the keypad buzzer
will provide a long beep indicating that the typed in characters have been cleared. NOTE for EKB3W: Even if Back-light Timeout has expired, the character will be considered as type in once the appropriate EKB3W key is
pressed. For more details, please refer to 33.1.7. Wireless Communication, Sleep Mode and Back-light Timeout .
Activate/deactivate
Configuration mode
26
EN
EKB3/
EKB3W
Enter installer code:
[INST] iiii #
Value: iiii– 4-digit installer code.
Example: INST1470#
MANUAL ELDES ESIM364 V1.6
EN50131-1
GRADE 3
Activate/deactivate
Configuration mode
EKB3/
+
Deactivate
Configuration mode
EKB3W
EKB3/
EKB3W
Enter installerr and master codes:
[INST] iiiiii mmmmmm #
Value: iiiiii – 6-digit installer code; mmmmmm - 6-digit master code.
Example: INST147000111111#
Enter installerr code:
[INST] iiiiii #
Value: iiiiii – 6-digit installer code.
Example: INST147000#
The following table provides a list of EKB3/EKB3W indications, which are relevant during Configuration mode.
Indication
Indicator ARMED flashing
Indicator SYSTEM flashing
1 long beep
3 short beeps
Description
Configuration mode activated successfully.
Valid parameter is entered and waiting for valid value to be enetered.
Non-existing command or invalid parameter value entered.
Command entered successfully.
NOTE: The system can be configured using only one keypad at a time. Other connected keypads will be inactive while the Configuration mode is activated.
NOTE: Configuration mode will automatically deactivate if 1 minute after the last key-stroke expires.
5.4. ELDES Configuration Tool Software
Config
Tool
Software ELDES Configuration Tool is intended for ESIM364 alarm system configuration locally via USB port or remotely via
GPRS network or Ethernet connection (ELAN3-ALARM device required). This software simplifies system configuration process
by allowing to use a personal computer in the process. Before starting to use ELDES Configuration Tool software, please read
the user guide provided in the software’s HELP section.
5.4.1. Remote System Configuration via Configuration Server
ATTENTION: The system will NOT send any data to monitoring station while configuring the system remotely via GPRS network or
Ethernet connection. However, during the configuration session, the data messages are queued up and transmitted to the monitoring
station after the configuration session is over.
ATTENTION: When the Configuration mode is activated by EKB3/EKB3W keypad or menu section CONFIGURATION is opened by the
installer using EKB2 keypad, remote system configuration will be disabled.
NOTE: The keypads will be inactive when the system is being configured remotely.
Before configuring ESIM364 remotely using GPRS network or Ethernet (using ELAN3-ALARM) connection, please ensure that:
•
SIM card is inserted into SIM CARD1 slot of ESIM364 device (see 2.2. Main Unit, LED & Connector Functionality).
•
Mobile internet service (GPRS) is enabled on the SIM card – required for GPRS network connection only.
•
APN, user name and password are set up (see 30.2.1. GPRS Network) – required for GPRS network connection only.
•
Power supply is connected to ESIM364.
•
Default SMS password is changed to a new 4-digit password (see 6. SMS PASSWORD AND INSTALLER CODE).
•
At least User 1 phone number is set up (see 8. USER PHONE NUMBERS).
GPRS network/
Internet
ESIM364
Internet
Configuration
Server
ELDES Configuration
Tool
Remote system configuration via GPRS network connection
MANUAL ELDES ESIM364 V1.6
EN
27
Ethernet/
Internet
ESIM364 &
ELAN3-ALARM
Internet
Configuration
Server
ELDES Configuration
Tool
Remote system configuration via Ethernet connection using ELAN3-ALARM
a) In order to activate a remote connection between ESIM364 system and ELDES configuration
server, please send the following SMS text message from preset user phone number. Upon
the successful SMS text message delivery, the system establishes a connection session for
20 minutes.
+
Initiate connection
with ELDES server
GPRS
ELAN3
ALARM
SMS text message content:
ssss_STCONFIG
Value: ssss – 4-digit SMS password.
Example: 1111_STCONFIG
SMS text message content:
ssss_STCONFIG:ELAN
Value: ssss – 4-digit SMS password.
Example: 1111_STCONFIG:ELAN
b) Once the SMS text message containing device IMEI number and confirming a successful connection establishment is received, please run ELDES Configuration Tool software.
c) Click Remote Connection Management...
d) In the next window, select Connect to Remote Server (recommended) and click Next
button.
e) In Device IMEI entry, enter the IMEI number previously received by SMS text message.
f) Click Continue button.
g) By default, upon the successfully established connection, the system will prompt for an installer code.
h) By entering a valid installer code, the system grants access to full configuration remotely.
i) Remote Configuration Management window displays all performed configuration actions and connectivity information.
5.4.2. Remote System Configuration via Direct Connection
ATTENTION: The system will NOT send any data to monitoring station while configuring the system remotely via GPRS network or Ethernet connection. However, during the configuration session, the data messages are queued up and transmitted to the monitoring station
after the configuration session is over.
ATTENTION: When the Configuration mode is activated by EKB3/EKB3W keypad or menu section CONFIGURATION is opened by the installer using EKB2 keypad, remote system configuration will be disabled.
NOTE: The keypads will be inactive when the system is being configured remotely.
Before configuring ESIM364 remotely using GPRS network or Ethernet (using ELAN3-ALARM) connection, please ensure that:
28
EN
MANUAL ELDES ESIM364 V1.6
•
SIM card is inserted into SIM CARD1 slot of ESIM364 device (see 2.2. Main Unit, LED & Connector Functionality) – required for GPRS
network connection only.
•
Mobile internet service (GPRS) is enabled on the SIM card – required for GPRS network connection only.
•
APN, user name and password are set up (see 30.2.1. GPRS Network) – required for GPRS network connection only.
•
Machine running ELDES Configuration Tool software provides access via public IP address.
•
TCP port 5000 is forwarded for the IP address of the machine running ELDES Configuration Tool software.
•
Power supply is connected to ESIM364.
GPRS network/
Internet
ELDES Configuration
Tool
ESIM364
Remote system configuration via GPRS network connection
Internet/
Ethernet
ELDES Configuration
Tool
ESIM364 &
ELAN3-ALARM
Remote system configuration via Ethernet connection
MANUAL ELDES ESIM364 V1.6
EN
29
5.4.2.1. Establishing Remote Connection Between ESIM364 System and ELDES Configuration Tool via GPRS Network
a) Run ELDES Configuration Tool software.
GPRS
b) Click Remote Connection Management...
c) In the next window, select Run TCP/IP Server (advanced) and click Next button.
d) Set a TCP port for listening for incoming connections or leave the default TCP
port 5000.
e) Click Continue button.
f) In order to activate a remote connection between ESIM364 system and ELDES
Configuration Tool software running as remote configuration server, please
send the following SMS text message from preset user phone number. Upon
the successful SMS text message delivery, the system establishes a connection
session for 20 minutes.
Initiate connection
with ELDES
Configuration Tool
GPRS
SMS text message content:
ssss_STCONFIG:add.add.add.add:pprrt or
ssss_STCONFIG:host-name:pprrt
Value: ssss – 4-digit SMS password; add.add.add.
add – public IP address of the machine running
ELDES Configuration Tool software; pprrt – TCP
port number, range – [1... 65535]; host-name –
public host-name of the machine running ELDES
Configuration Tool software.
Example: 1111_STCONFIG:62.80.115.102:4522
g) By default, upon the successfully established connection, the system will
prompt for an installer code.
h) By entering a valid installer code, the system grants access to full configuration
remotely.
i) Remote Configuration Management window displays all performed configuration actions and connectivity information.
30
EN
MANUAL ELDES ESIM364 V1.6
5.4.2.2. Establishing Remote Connection Between ESIM364 System and ELDES Configuration Tool via Ethernet Using ELAN3-ALARM
ELAN3
ALARM
a) Run ELDES Configuration Tool software.
b) Click Remote Connection Management...
c) In the next window, select Connect via ELAN3-ALARM and click Next button.
d) Click Continue button.
e)In LAN IP Address entry, enter the public IP address of ELAN3-ALARM device
and click Continue button.
f) By default, upon the successfully established connection, the system will
prompt for an installer code.
g) By entering a valid installer code, the system grants access to full configuration
remotely.
h) Remote Configuration Management window displays all performed configuration actions and connectivity information.
5.4.3. Ending the Configuration Process
After the system configuration is complete, use one of the following methods to end the configuration process:
GPRS
ELAN3
ALARM
•
Click Disconnect or Stop button and close ELDES Configuration Tool software;
•
The session will automatically expire in 20 minutes. Before the last 5 minutes, the software will offer the user to
extend the session for another 20 minutes.
•
Alternatively, the connection with the server can be terminated at any time by sending an SMS text message.
Shut down the
Connection
with the Server
SMS text message content:
ssss_ENDCONFIG
Value: ssss – 4-digit SMS password.
Example: 1111_ENDCONFIG
Once the session is expired or terminated, the system will reply with an SMS text message confirming the end of the session.
MANUAL ELDES ESIM364 V1.6
EN
31
6.SMS PASSWORD AND INSTALLER CODE
For security reasons, the system uses the following type of password and code:
SMS password – 4-digit password used for system arming/disarming and configuration by SMS text messages. By default, SMS password is
0000, which MUST be changed!. SMS password is authorized to carry out the following:
•
Access system configuration by SMS text messages.
•
Arm/disarm partition.
•
Activate/deactivate service mode.
•
Set system date and time.
•
Add/remove user phone numbers.
•
Set SMS password.
•
Turn ON/OFF PGM outputs.
•
Restart system remotely.
Installer code – 4-digit password used for system configuration by EKB2/EKB3/EKB3W keypad and ELDES Configuration Tool
software. By default, installer code is 1470, which is highly recommended to change. Installer code is authorized to carry out
the following:
•
Access system configuration by keypad and ELDES Configuration Tool software.
•
Set installer code.
•
Set master code.
•
Activate/deactivate service mode.
•
Set system date and time.
•
Add/remove user phone numbers.
•
Set SMS password.
•
Turn ON/OFF PGM outputs.
•
Restore system configuration to default.
•
Clear tamper fault (if enabled).
Set SMS password
SMS
EKB2
Enter parameter 14 & new SMS password:
14 ssss #
Value: ssss – 4-digit new SMS password; range – [0001... 9999].
Example: 141111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → 1470 → OK → PRIMARY SETTINGS → OK → INSTALLER CODE → OK → iiii → OK
Value: iii – 4-digit new installer code; range – [0000... 9999].
EKB3/
EKB3W
32
EN
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → SMS PASSWORD → OK → ssss → OK
Value: iiii – 4-digit installer code; ssss – 4-digit new SMS password; range – [0001... 9999].
EKB3W
EKB3/
Set installer code
SMS text message content:
wwww_PSW_ssss
Value: wwww – 4-digit existing SMS password; ssss – 4-digit new SMS password; range –
[0001... 9999].
Example: 0000_PSW_1111
Enter parameter 16 & new installer code:
16 iiii #
Value: iii – 4-digit new installer code; range – [0000... 9999].
Example: 162538#
MANUAL ELDES ESIM364 V1.6
Config
Tool
EN50131-1
GRADE 3
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following features:
• All codes and passwords must consist of 6 digits.
• The system must prompt for master (see 10. MASTER AND USER CODES) and installer (see 6. SMS PASSWORD AND INSTALLER CODE) codes when configuring the system by EKB2, EKB3, EKB3W keypad or ELDES Configuration Tool software.
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please
refer to 36. EN 50131-1 GRADE 3.
7.SYSTEM LANGUAGE
The system comes equipped with a single language for communication with the user by SMS text messages and EKB2 keypad menu display.
The system language depends on ESIM364 firmware, which is based on the user’s location.
List of currently available system languages (firmwares):
• Czech
• English
• Estonian
• Finnish
• French
• German
• Greek
• Hungarian
• Italian
• Latvian
• Lithuanian
• Polish
• Portuguese
• Romanian
• Russian
• Slovak
• Spanish
NOTE: To obtain a firmware that features a different SMS and EKB2 menu language, please contact your local dealer.
MANUAL ELDES ESIM364 V1.6
EN
33
8.USER PHONE NUMBERS
The system supports up to 10 user phone numbers identified as User 1 through 10. When the phone number is set, the user will be able to
arm/disarm the system by SMS text messages and free of charge phone calls (see 12.1. Free of Charge Phone Call and 12.2. SMS Text
Message) as well as to configure the system by SMS text messages. User phone numbers are also used to receive alarm phone calls via
GSM connection and SMS text messages from the system (see 17. ALARM INDICATIONS AND NOTIFICATIONS).
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS text
messages containing wrong SMS password even from a preset user phone number (see 8.2. System Control from any Phone Number).
To set User 1 phone number is mandatory, while the other 9 are optional. The supported phone number formats are the following:
•
International (with plus) – The phone numbers must be entered starting with plus and an international country code in the following format: +[international code][area code][local number], example for UK: +4417091111111. This format can be used when
setting up the phone number by SMS text message and ELDES Configuration Tool software.
•
International (with 00) – The phone numbers must be entered starting with 00 and an international country code in the following
format: 00[international code][area code][local number], example for UK: 004417091111111. This format can be used when setting up the phone number by SMS text message, EKB2/EKB3/EKB3W keypad and ELDES Configuration Tool software.
•
Local – The phone numbers must be entered starting with an area code in the following format: [area code][local number], example
for UK:017091111111. This format can be used when setting up the phone number by SMS text message, EKB2/ EKB3/EKB3W keypad and ELDES Configuration Tool software.
Add user phone
number
SMS
EKB2
EKB3/
EKB3W
Config
Tool
View user phone
number
34
EN
SMS text message content:
ssss_NRup:ttteeellnnuumm
Value: ssss – 4-digit SMS password; up – user phone number slot, range – [1... 10]; ttteeellnnuumm – up to 15 digits user phone number.
Example: 1111_NR1:+4417091111111
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → USERS → OK →
GSM USER 1... 10 → OK → PHONE NUMBER → OK → ttteeellnnuumm → OK
Value: iiii – 4-digit installer code; ttteeellnnuumm – up to 15 digits user phone number.
Enter parameter 17, user phone number slot & phone number:
17 up ttteeellnnuumm #
Value: up – user phone number slot, range – [01... 10]; ttteeellnnuumm – up to 15 digits user
phone number.
Example: 1701004417091111111#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_HELPNR
Value: ssss – 4-digit SMS password.
Example: 1111_HELPNR
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → USERS → OK →
GSM USER 1... 10 → OK → PHONE NUMBER
Value: iiii – 4-digit installer code;
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Delete user phone
number
SMS
SMS text message content:
ssss_NRup:DEL
Value: ssss – 4-digit SMS password; up – user phone number slot, range – [2... 10].
Example: 1111_NR2:DEL
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → USERS → OK →
GSM USER 2... 10 → OK → PHONE NUMBER → OK → OK
Value: iiii – 4-digit installer code;
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: NEVER add a phone number of the device’s SIM card as a user phone number!
ATTENTION: Once User 1 phone number is set, it will be restricted to modify it only.
NOTE:
Multiple user phone numbers can be set by a single SMS text message, Example: 1111_NR1:+4417091111111_
NR2:+4417091111112_NR6:017091111113_NR10:+4417091111114
NOTE: Multiple user phone numbers can be deleted by a single SMS text message, Example: 1111_NR2:DEL_NR3:DEL_NR6:DEL_NR9:DEL_
NR:10:DEL
8.1. User Phone Number Names
When the system is armed or disarmed by free of charge phone call or SMS text message, the system sends a confirmation by SMS text message to user phone number that the system arming/disarming was initiated from. The SMS text message is sent regarding each partition
separately and contains system status and partition name as well as it may contain a user name, set to the user phone number.
Manage user phone
number name
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
8.2. System Control from any Phone Number
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS
text messages containing wrong SMS password even from a preset user phone number. To allow/disallow system arming/disarming by
phone call and SMS text messages that contain a valid SMS password from any phone number, please refer to the following configuration
methods.
Enable system control
from any phone
number
SMS
SMS text message content:
ssss_STR:ON
Value: ssss – 4-digit SMS password.
Example: 1111_STR:ON
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → CTRL FROM ANY
NUM → OK → ENABLE → OK
Value: iiii – 4-digit installer code;
EKB3/
EKB3W
Config
Tool
MANUAL ELDES ESIM364 V1.6
Enter parameter 12 & parameter status value:
12 1 #
Example: 121#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
35
Disable system
control from any
phone number
SMS
SMS text message content:
ssss_STR:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_STR:OFF
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → CTRL FROM ANY
NUM → OK → DISABLE → OK
Value: iiii – 4-digit installer code;
EKB3/
EKB3W
Config
Tool
36
EN
Enter parameter 12 & parameter status value:
12 0 #
Example: 120#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
9.DATE AND TIME
The system comes equipped with internal real-time clock (RTC) that keeps track of the current date and time. Once the system is up and
running, the user must set the correct date and time, otherwise the system will not operate properly. By default, after shutting down and
starting up the system, the date and time must be set again.
Set date and time
SMS
EKB2
EKB3/
EKB3W
Config
Tool
SMS text message content:
ssss_yyyy.mt.dd_hr:mn
Value: ssss – 4-digit SMS password; yyyy – year; mt – month, range – [01... 12]; dd – day, range
– [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59].
Example: 1111_2014.03.16_14:33
Menu path:
a) OK → uumm → OK → DATE/TIME SETTINGS → OK → yyyy-mt-dd hr:mn → OK
b) OK → iiii → OK → PRIMARY SETTINGS → OK → DATE/TIME SETTINGS → OK → yyyy-mt-dd
hr:mn → OK
Value: uumm – 4-digit user/master code; yyyy – year; mt – month, range – [01... 12]; dd – day,
range – [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59]; iiii – 4-digit
installer code.
Enter parameter 66, date & time:
66 yyyy mt dd hr mn#
Value: yyyy – year; mt – month, range – [01... 12]; dd – day, range – [01... 31]; hr – hours, range
– [00... 23]; mn – minutes, range – [00... 59].
Example: 66201405291235#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: When the system is connected to the monitoring station via GPRS network connection (see 30. MONITORING STATION) and/or
when Smart Security feature is in use (see 37. SMART SECURITY), the date and time will be automatically synchronized with the
monitoring station or Smart Security server upon the system startup.
9.1. Automatic Date and Time Synchronization
This feature enables the system to set the date and time automatically without the user being involved in this process. The system supports the following methods of automatic date and time synchronization that are used automatically on system start-up and periodically
(by default – every 30 days):
•
Via GSM network – Once enabled, the system automatically sends a date/time request to the GSM operator. This method is the
most accurate synchronization method. Some GSM operators might not support it.
•
By SMS text message – Once enabled, the system automatically sends the SMS text message to its own phone number and retrieves the date and time from the SMS text message reply, as the included date and time is set by the SMSC (SMS center). This
method is not as accurate as the synchronization via GSM network, but always effective.
By default, synchronization via GSM network is disabled. To enable/disable automatic date and time synchronization via GSM network,
please refer to the following configuration methods.
Enable/disable
synchronization via
GSM network
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, synchronization by SMS text message is disabled. To enable/disable automatic date and time synchronization by SMS text message, please enter/remove device phone number using one of the following configuration methods.
Enter/remove device
phone number for
synchronization by
SMS text message
MANUAL ELDES ESIM364 V1.6
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
37
10.MASTER AND USER CODES
ATTENTION: User/master code management must be carried out using master code and without Configuration mode being activated
by the EKB3/EKB3W keypad.
NOTE for EKB3/EKB3W: User/master code management must be carried out using master code and without Configuration mode
being activated by the EKB3/EKB3W keypad.
NOTE for EKB3/EKB3W: Master code management cat be carried out using an existing master code and without Configuration mode
being activated or by activating Configuration mode using the installer code.
The system supports up to 30 numeric codes, identified as Master code and User code 1 through 29, allowing to carry out system arming/
disarming as well as minor system configuration and control by the keypad.
Master code is authorized to carry out the following:
•
Arm/disarm partition.
•
Bypass violated zones.
•
View violated zones and tampers.
•
View system faults.
•
Set system date and time.
•
View temperature sensor information.
•
View event log,
•
View and clear alarm log,
•
Set/delete user codes.
•
Assign user code as Duress code.
•
Assign user code as SGS code.
User code is authorized to carry out the following:
•
Arm/disarm partition.
•
Bypass violated zones.
•
View violated zones and tampers.
•
View system faults.
•
Set system date and time.
•
View temperature sensor information.
•
View and clear alarm log.
By default, only Master code is preset as 1111 and assigned to Partition 1, 2, 3 and 4. For more details regarding User/Master code partition,
please refer to 23.4. User/Master Code Partition.
Set master code
EKB2
EKB3/
EKB3W
Menu path:
a) OK → vvvv → OK → CODES → OK → MASTER CODE → OK → → CODE → OK → mmmm → OK
b) OK → iiii → OK → PRIMARY SETTINGS → OK → MASTER CODE → mmmm → OK
Value: vvvv – 4-digit existing master code, range – [0000... 9999]; iiii – 4-digit installer
code; mmmm – 4-digit new master code, range – [0000... 9999].
a) Press [CODE], [0], enter existing master code & new master code:
[CODE] [0] vvvv 01 mmmm #
Value: vvvv – 4-digit existing master code; mmmm - 4-digit new master code; range [0000... 9999].
Example: CODE01111012222#
b) Enter parameter 63, existing master code & new master code:
63 vvvv mmmm #
Value: vvvv – 4-digit existing master code; mmmm – 4-digit new master code, range –
[0000... 9999].
Example: 6311112222#
Config
Tool
38
EN
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Set user code
EKB2
EKB3W
Press [CODE], [0], enter master code, user code slot & user code:
[CODE] [0] mmmm us uuuuu #
Value: mmmm - 4-digit master code; us - user code slot, range - [02... 30]; uuuu - 4-digit user
code, range - [0000... 9999].
Example: CODE01111092556#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → mmmm → OK → CODES → OK → REMOVE CODE → OK → uuuu → OK
Value: mmmm – 4-digit master code; uuuu – 4-digit user code.
EKB3/
Delete user code
Menu path:
User code 2... 16: OK → mmmm → OK → CODES → OK → USER CODE (2-16) → OK → USER
CODE 2... 16 → OK → CODE → OK → uuuu → OK
User code 17... 30: OK → mmmm → OK → CODES → OK → USER CODE (17-30) → OK → USER
CODE 17... 30 → OK → CODE → OK → uuuu → OK
Value: mmmm – 4-digit master code; uuuu – 4-digit user code, range – [0000... 9999].
EKB3W
Press [CODE], [0], enter master code & user code slot:
[CODE] [0] mmmm us #
Value: mmmm - 4-digit master code; us - user code slot, range - [02... 30].
Example: CODE0111109#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
NOTE: The system does not allow to set a duplicate code.
Master code or one of the user codes ranging from User code 2 through 9 can be set as SGS (Security Guard Service) code, which is used
for system arming/disarming by a security service employee. When used, the SGS code will be identified by a unique Contact ID code in the
monitoring station.
Set SGS code
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
Master code: OK → mmmm → OK → CODES → OK → SGS CODE → OK → N/A | MASTER CODE → OK
User code: OK → mmmm → OK → CODES → OK → SGS CODE → OK → N/A | USER CODE 2... 10 → OK
Value: mmmm – 4-digit master code; N/A – SGS code not in use.
Press [CODE], [4], user code slot & enter master code:
Master code: [CODE] [4] 01 mmmm #
User code: [CODE] [4] us mmmm #
Value: us - user code slot, range - [02... 30]; mmmm - 4-digit master code.
Example: CODE4041111#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The Duress code is used when system disarming is demanded by force. When used, the system will disarm as well as it will silently transmit
an alert to the monitoring station. Only Master code one of the user codes ranging from User code 2 through 9 can be set as Duress code.
MANUAL ELDES ESIM364 V1.6
EN
39
Set Duress code
EKB2
EKB3/
EKB3W
Config
Tool
EN50131-1
GRADE 3
Menu path:
Master code: OK → mmmm → OK → CODES → OK → DURESS CODE → OK → N/A |MASTER
CODE → OK
User code: OK → mmmm → OK → CODES → OK → DURESS CODE → OK → N/A | USER CODE
2... 10 → OK
Value: mmmm – 4-digit master code; N/A – Duress code not in use.
Press [CODE], [3], 01/user code slot & enter master code:
Master code: [CODE] [3] 01 mmmm #
User code: [CODE] [3] us mmmm #
Value: us - user code slot, range - [02... 30]; mmmm - 4-digit master code.
Example: CODE3081111#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following features:
•
All codes and passwords must consist of 6 digits.
•
The system must prompt for master (see 10. MASTER AND USER CODES) and installer (see 6. SMS PASSWORD AND INSTALLER CODE) codes when configuring the system by EKB2, EKB3, EKB3W keypad or ELDES Configuration Tool software.
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please
refer to 36. EN 50131-1 GRADE 3.
10.1. Master and User Code Names
When the system is armed or disarmed by entering a master or user code using a keypad, the system sends a confirmation by SMS text message to user phone number, sharing the same partition (-s) as the keypad and user/master code. The SMS text message is sent regarding
each partition separately and contains system status and partition name as well as it may contain a user name, set to the user/master code.
Manage user/master
code name
40
EN
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
11.iBUTTON KEYS
An iButton key is a unique 64-bit ID code containing chip enclosed in a stainless steel tab usually implemented in a small plastic holder.
ESIM364 system supports up to 16 iButton keys each holding a unique identity code (ID), which is used for system arming and disarming.
11.1. Adding and Removing iButton Keys
To add an iButton key to the system, do the following:
a) Disarm the system in all partitions (see 12. ARMING AND DISARMING).
b) Enable Allow Adding New iButton Keys mode.
c) T ouch the key to the iButton key reader when the system is disarmed (see Fig. No. 32).
32
d) The successfully added iButton key will be indicated by short beeps emitted by the system’s buzzer.
e) Add as many iButton keys as necessary – touch one key after another to the reader – until the number of 16 keys is reached.
NOTE: iButton Key 1 can be added without Allow Adding New iButton Keys mode being enabled.
Enable Allow Adding
New iButton Keys
mode
SMS
SMS text message content:
ssss_IBPROG:ON
Value: ssss – 4-digit SMS password.
Example: 1111_IBPROG:ON
EKB2
Menu path:
OK → iiii → OK → IBUTTON KEYS → OK → NEW IBUTTON → OK → ENABLE → OK
Value: iiii - 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 18 & parameter status value:
18 0 #
Example: 180#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When adding of iButton keys is complete, please disable Allow Adding New iButton Keys mode.
MANUAL ELDES ESIM364 V1.6
EN
41
Disable Allow Adding
New iButton Keys
mode
SMS
SMS text message content:
ssss_IBPROG:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_IBPROG:ON
EKB2
Menu path:
OK → iiii → OK → IBUTTON KEYS → OK → NEW IBUTTON → OK → DISABLE → OK
Value: iiii - 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 18 & parameter status value:
18 1 #
Example: 181#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To view the ID of the added iButton keys, please refer to the following configuration methods.
View iButton key ID
EKB2
Menu path:
OK → iiii → OK → IBUTTON KEYS → OK → IBUTTON → OK → IBUTTON 1...16 → OK → ID
Value: iiii - 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If the iButton key is lost or stolen, due to security reasons it is highly recommended to remove it from the system.
Remove individual
iButton key from the
system
Remove all iButton
keys from the system
EKB2
Menu path:
OK → iiii → OK → IBUTTON KEYS → OK → IBUTTON → OK → IBUTTON 1...16 → OK →
REMOVE → OK
Value: iiii - 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_RESETIB
Value: ssss – 4-digit SMS password.
Example: 1111_RESETIB
11.2. iButton Key Names
When the system is armed or disarmed by iButton key, the system sends a confirmation by SMS text message to preset user phone number,
42
EN
MANUAL ELDES ESIM364 V1.6
sharing the same partition (-s) as the key. The SMS text message is sent regarding each partition separately and contains system status and
partition name as well as it may contain a user name, set to the iButton key.
Manage iButton key
name
MANUAL ELDES ESIM364 V1.6
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
43
12.ARMING AND DISARMING
The system features the following methods to carry out arming and disarming process:
•
Free of charge phone call.
•
SMS text message.
•
EKB2/EKB3/EKB3W keypad and user/master code.
•
iButton key.
•
EWK1/EWK2 wireless keyfob.
•
Arm-Disarm by Zone.
•
EGR100 middle-ware.
The system arms/disarms the partitions that the preset user phone number, EKB2/EKB3/EKB3W keypad and user/master code, iButton key,
EWK1/EWK2 wireless keyfob or zone, set up for Arm-Disarm by Zone method, are assigned to. For example, if User 1 phone number is assigned
to Partition 1, 2 and 4, the user will be able to arm/disarm Partition 1, 2 and 4 by a single phone call to the system (see 23. PARTITIONS).
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message. For more details on SMS
text message regarding system arming/disarming and how to manage it, please refer to 12.9. Disabling and Enabling Arm/Disarm
Notifications.
The system will allow to arm the system if the following system faults are present (see 29. INDICATION OF SYSTEM FAULTS):
• Main power supply is lost.
•
Low battery.
•
Battery dead or missing.
•
Battery failed.
•
Siren failed.
•
Date/time not set.
•
GSM connection failed.
•
GSM/GPRS antenna failed.
•
Wireless antenna failed.
•
Keypad lost.
When attempting to arm the system (by any method, except EKB2/EKB3/EKB3W keypad and user/master code, EGR100 middle-ware) in
case of violated zone/tamper presence, the system will reply with SMS text message containing violated zone/tamper number. Due to
security reasons it is highly recommended to restore the violated zone/tamper before arming the system. For more details on how to arm
the system despite the violated zone presence, please refer to 14.6. Zone Attributes and 14.7. Bypassing and Activating Zones.
The system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS text messages
containing wrong SMS password even from a preset user phone number. For more details regarding arming/disarming the system from a
non-preset phone number, please refer to 8.2. System Control from any Phone Number.
NOTE: The system remembers the last status (armed/disarmed) of all partitions even after complete shut down.
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following feature:
• System arming is blocked if any system fault exists. The user will not be able to arm the system until all existing system
faults are solved.
• System arming is blocked until tamper fault is cleared by the installer.
EN50131-1
GRADE 3
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please
refer to 36. EN 50131-1 GRADE 3.
12.1. Free of Charge Phone Call
To arm and disarm the system, dial the system‘s phone number from any of 10 available user phone numbers (see 8. USER
PHONE NUMBERS for user phone number management). The phone call is free charge as the system rejects it and carries out
arming/disarming procedure afterwards. When arming – the system rejects the phone call after 2 rings, when disarming – the
system rejects the phone call immediately. If there is more than one preset user dialing to the system at the same time, the
system will accept the incoming call from the user who was the first to dial while other user (-s) will be ignored.
When system’s phone number is dialed for arming, the system will proceed as follows:
•
44
Non-partitioned system:
•
If ready (no violated zone/tamper), the system will arm.
•
If unready (violated zone/tamper is present), the system will not arm and provide a list of violated zones/tampers by SMS text
message to user phone number.
EN
MANUAL ELDES ESIM364 V1.6
•
Partitioned system:
•
If all partitions are disarmed ready, the system will arm them.
•
If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and
skip the unready one (-s). The system will then send an SMS text message, containing a list of violated zones/tampers, to user
phone number that the system arming was initiated from.
If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions and skip
the armed ones.
•
When a user phone number is assigned to multiple partitions, the user will be able arm/disarm the corresponding system partitions by
dialing the system’s phone number. For example, if User 1 is assigned to Partition 1, 2 and 3, the user will be able to arm/disarm Partition 1,
2 and 3 by a single phone call to the system from User 1 phone number. For more details on how to set user phone number partition, please
refer to 23.2. User Phone Number Partition.
33
CALL
User
ESIM364
12.2. SMS Text Message
SMS
To arm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user
phone numbers (see 8. USER PHONE NUMBERS for user phone number management). When the SMS text message for arming is sent to the system’s phone number, the system will proceed as follows:
•
•
Non-partitioned system:
•
If ready (no violated zone/tamper), the system will arm.
•
If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number.
Partitioned system:
•
If all partitions are disarmed ready (no violated zone/tamper), the system will arm them.
•
If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and skip the unready one (-s). The system will then send an SMS text message, containing a list of violated
zones/tampers, to user phone number that the system arming was initiated from.
•
If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions
and skip the armed ones.
Arm the system
SMS text message content:
ssss_ARMp or ssss_ARMp,p,p,p
Value: ssss – 4-digit SMS password; p – partition number, range – [1... 4].
Example: 1111_ARM1
34
SMS
User
ESIM364
To disarm the system by SMS text message, send the following text to the system‘s phone number from any of 10 available user phone numbers:
MANUAL ELDES ESIM364 V1.6
EN
45
Disarm the system
SMS text message content:
ssss_DISARMp or ssss_DISARMp,p,p,p
Value: ssss – 4-digit SMS password; p – partition number, range – [1... 4].
Example: 1111_DISARM1,2,4
35
SMS
User
ESIM364
When a user phone number is assigned to multiple partitions, the user will be able arm/disarm the corresponding system partitions by
sending the SMS text message to the system’s phone number. For example, if User 3 is assigned to Partition 2 and 3, the user will be able
to arm/disarm Partition 2 and/or 3 by sending an SMS text message from User 3 phone number. For more details on how to set user phone
number partition, please refer to 23.2. User Phone Number Partition.
12.3. EKB2 Keypad and User/Master Code
icon displayed next to the partition name in the home screen view of EKB2 keypad indicates that no violated zones and/or tampers are present, therefore the partition is ready for arming. If icon is displayed instead, the partition is unready for arming, therefore the user must restore all violated zones and/or tampers before arming the partition. Alternatively, the violated zones can be bypassed (see 14.7. Bypassing
and Activating Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
icon appears in the home screen view if system fault (-s) exist (see 29. INDICATION OF SYSTEM FAULTS).
To arm the system by EKB2 keypad, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad (see
10. MASTER AND USER CODES for user/master code management). By default, the arming process is as follows:
Non-partitioned system:
a) When a valid user or master code is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps, the keypad
will switch to home screen view and display the countdown timer.
b) When a valid user or master code is entered, the keypad will display the partition selection menu. Once the partition is selected, the
system will initiate exit delay. During the exit delay, the keypad’s buzzer will emit short beeps and the keypad will display ARMING
part-name message for 3 seconds followed by partition selection menu. When the keypad back-light timeout expires, the home
screen view will follow. If
key is touched twice during exit delay, the keypad will return to home screen view and display the countdown timer next to the partition name .
When successfully armed:
•
•
by default, the countdown timer will disappear.
in addition, if enabled, the keypad will display
icon next to the partition name that has been armed.
Partitioned system; arming a single partition as the keypad is assigned to – When a valid user or master code is entered, the keypad will display the partition selection menu. Once a partition that is to be armed is selected, the system will initiate exit delay. During the
exit delay, the keypad’s buzzer will emit short beeps and the keypad will display ARMING part-name message for 3 seconds followed by
partition selection menu. When the keypad back-light timeout expires, the home screen view will follow. If
key is touched twice during
exit delay, the keypad will return to home screen view and display the countdown timer next to the partition name that is being armed.
When successfully armed:
•
•
by default, the countdown timer will disappear.
in addition, if enabled, the keypad will display
icon next to the partition name that has been armed.
Partitioned system; arming a different single partition than the keypad is assigned to – When a valid user or master code is
entered, the keypad will display the partition selection menu. Once a partition that is to be armed is selected, the system will initiate exit
delay, but will not indicate it on EKB2 keypad due to the difference between keypad partition and the one being armed. Then the keypad will
display ARMING part-name message for 3 seconds followed by partition selection menu. When the keypad back-light timeout expires,
the home screen view will follow. Alternatively, the
key may be touched in order to instantly return to home screen view.
Partitioned system; arming multiple partitions simultaneously – When a valid user or master code is entered, the keypad will display the partition selection menu. Once ARM ALL menu item is selected the system will proceed as follows:
•
if all partitions are disarmed-ready (no violated zone/tamper), the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and the keypad will display multiple ARMING part-name messages for 3 seconds reflecting each partition the user/master code is assigned to, followed by partition selection menu.
•
if one or more partitions are disarmed-unready (contains violated zone/tamper), the system will initiate exit delay. During the exit delay, the keypad’s buzzer will emit short beeps and the keypad will display ARMING part-name message (-s) reflecting ready partition
(-s), while the unready partition (-s) will be skipped indicated by part-name NOT READY message (-s) followed by partition selection
menu. Each message will be displayed for 2 seconds and corresponds to the partition (-s) the user/master code is assigned to.
•
if a combination of armed and disarmed-ready partitions exist, the system will initiate exit delay. During the exit delay, the keypad’s
46
EN
MANUAL ELDES ESIM364 V1.6
buzzer will emit short beeps and the keypad will display ARMING part-name message (-s) seconds reflecting ready partition (-s),
while the pre-armed partition (-s) will be skipped. Each message will be displayed for 2 seconds and corresponds to the partition (-s)
the user/master code is assigned to.
When the keypad back-light timeout expires, the home screen view will follow. If key
is touched twice during exit delay, the keypad will
return to home screen view and display the countdown timers next to the partition names the keypad is assigned to. When successfully
armed:
•
by default, the countdown timers will disappear.
•
in addition, if enabled, the keypad will display
Arm the system
icon next to the partition name that has been armed.
Enter user/master code (and select partition):
Non-partitioned system:
a) uumm → OK
b) OK → uumm → OK → ARM/DIS PARTITION → OK → [p] part-name → OK
Partitioned system – arming a single partition: uumm → OK → [p] part-name → OK or OK → uumm → OK
→ ARM/DIS PARTITION → OK → [p] part-name → OK
Partitioned system – arming multiple partitions: uumm → OK → ARM ALL → OK or OK → uumm → OK →
ARM/DIS PARTITION → OK → ARM ALL → OK
Value: uumm – 4-digit user/master code; p – partition number, range – [1... 4], part-name – up to 15
characters partition name.
To cancel the arming process:
•
Non-partitioned system – Enter the user/master code again during exit delay countdown.
•
Partitioned system – Select the partition again, that is currently being armed, from the partition selection menu during exit delay
countdown. The keypad will display part-name ARMING TERMINATED message for 2 seconds followed by partiton selection menu.
To disarm or turn OFF the alarm, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad. By
default, the system disarming process is as follows:
Non-partitioned system:
a) When a valid user or master code is entered, the keypad will switch to home screen view.
b) When a valid user or master code is entered, the keypad will display the partition selection menu. Once the partition is selected, the
keypad will display part-name DISARMED message for 3 seconds and return to partition selection menu followed by home screen
view after the keypad back-light timeout expires. Alternatively, the
ikonas key may be touched in order to instantly return to home
screen view.
Partitioned system; disarming a single partition – When a valid user or master code is entered, the keypad will display the partition
selection menu. Once a partition that is to be disarmed is selected, the keypad will display part-name DISARMED message for 2 seconds
and return to partition selection menu followed by home screen view after the keypad back-light timeout expires.
Partitioned system; disarming multiple partitions simultaneously – When a valid user or master code is entered, the keypad will
display the partition selection menu. Once DISARM ALL menu item is selected, the keypad will display multiple part-name DISARMED
messages for 2 seconds reflecting each partition the user/master code is assigned to and return to partition selection menu followed by
home screen view after the keypad back-light timeout expires. Alternatively, the
ikonas key may be touched in order to instantly
return to home screen view.
Disarm the system
Enter user/master code (and select partition):
Non-partitioned system:
a) uumm → OK
b) OK → uumm → OK → ARM/DIS PARTITION → OK → [p] part-name → OK
Partitioned system – disarming a single partition: uumm → OK → [p] part-name → OK or OK → uumm →
OK → ARM/DIS PARTITION → OK → [p] part-name → OK
Partitioned system – disarming multiple partitions: uumm → OK → ARM ALL → OK or OK → uumm → OK
→ ARM/DIS PARTITION → OK → ARM ALL → OK
Value: uumm – 4-digit user/master code; p – partition number, range – [1... 4], part-name – up to 15
characters partition name.
When a user/master code is assigned to multiple partitions, the user will be able arm/disarm the corresponding system partitions by EKB2
keypad using partition selection menu. However, if a user/master code is assigned to Partition 1, 2 and 4, while EKB2 keypad is assigned
to Partition 2, the user will be able to arm/disarm Partition 1, 2 and 4, but the keypad will only display Partition 2 name and the related information in home scren view. For more details on how to set keypad partition and user/master code partition, please refer to 23.4. User/
Master Code Partition.
Enable/disable Show
ARMED status in
keypad
MANUAL ELDES ESIM364 V1.6
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
47
NOTE: If the user fails to enter a correct user/master code 10 times in a row, the system will block the keypad for 2 minutes and the keypad
will display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user/master code. The
keypad will automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message.
NOTE: The keypad will display
icon and icon next to the armed and disarmed partition name in home screen view respectively only if
Show ARMED status in keypad parameter is enabled and the keypad is assigned to the same partition (-s) as the armed/disarmed one.
12.4.EKB3 Keypad and User/Master Code
ATTENTION: EKB3 keypad can operate either in 2-partition or in 4-partition mode. The description of the following procedure is based on
4-partition mode operation on EKB3 keypad. The arming/disarming procedure in 2-partition mode using EKB3 keypad would be carried out
identically to EKB3W wireless keypad. For more details on 2-partition mode, please refer to 12.5. EKB3W Keypad and User/Master Code
Illuminated indicator READY on EKB3 keypad indicates that no violated zones and/or tampers are present, therefore the partition is ready
for arming. If the indicator READY is not illuminated, the partition is unready for arming, therefore the user must restore all violated zones
and/or tampers before arming the partition. Alternatively, the violated zones can be bypassed (see 14.7. Bypassing and Activating
Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes). Indicator SYSTEM will illuminate or flash if system fault (-s) exist (see 29. INDICATION OF SYSTEM FAULTS).
To arm the system by EKB3 keypad, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad
(see 10. MASTER AND USER CODES for user/master code management). By default, the arming process is as follows:
Non-partitioned system/Partitioned system; arming a single partition as the keypad is assigned to – When a valid user/master code is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps and the indicator ARMED along with the
number [1]... [4] key, indicating the partition that is to be armed, will light ON. When the system is successfully armed, the keypad’s buzzer
will silent down.
Arm the system
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 2222
0
Partitioned system; arming a different single partition than the keypad is assigned to – To arm a different partition than the
keypad is assigned to, use keypad partition switch feature (by default – disabled; see 23.3. Keypad Partition and Keypad Partition
Switch) before arming process. Once the partition is swiched and a valid user/master code is entered, the system will initiate exit delay,
the keypad’s buzzer will emit short beeps and the indicator ARMED along with the number [1]... [4] key, indicating the partition that is to be
armed, will light ON. When the system is successfully armed, the keypad’s buzzer will silent down.
Use keypad
partition switch
Arm the system
Hold the [1]... [4] key and release it after 3 short beeps:
Value: [1]... [4] key – parition number 1... 4
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 2222
0
Partitioned system; arming multiple partitions simultaneously – If a user/master code assigned to all 4 partitions exist, user can
arm all partitions simultaneously. When this feature is used, the system will proceed as follows:
•
if all partitions are disarmed-ready (no violated zone/tamper), the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and indicator ARMED along with number [1], [2], [3] and [4] keys will light ON. When the system is successfully armed, the keypad’s buzzer will silent down.
•
if one or more partitions are disarmed-unready (keypad number [1]... [4] key flashing, indicating the partition that contains violated
zone/tamper), the system will initiate exit delay. During the exit delay, the keypad’s buzzer will emit short beeps and keypad indicator
ARMED (if the keypad is switched to a non-violated partition) along with the number [1]... [4] key, indicating the partition that is to be
armed, will light ON. The ready partition (-s) will be armed and the unready one (-s) will be skipped.
•
if a combination of armed and disarmed ready partitions is present, the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and keypad indicator ARMED (if the keypad is switched to a disarmed partition) along with the number
[1]... [4] key, indicating the partition that is to be armed, will light ON. The disarmed-ready partitions will be armed and the pre-armed
ones will be skipped.
48
EN
MANUAL ELDES ESIM364 V1.6
Arm all 4 partitions
simultaneously
1
2
3
4
5
6
7
8
9
0
Hold the [0] key, release it after 3 short beeps and enter user/
master code:
0 uumm
Value: uumm – 4-digit user/master code.
Example: 0 2222
The system will arm/disarm the partition corresponding to the one that user/master code (see 23.4. User/Master Code Partition) and
the keypad (see 23.3. Keypad Partition and Keypad Partition Switch) are assigned to. For example, if User code 4 is assigned to Partition 2, 3 and 4, while EKB3 keypad is assigned to Partition 2, the user will be able to arm/disarm only Partition 2 by entering User code 4.
To cancel the arming process, enter the user/master code again during exit delay countdown.
To disarm or turn OFF the alarm, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad. By
default, the system disarming process is as follows:
Non-partitioned system/Partitioned system; disarming a single partition as the keypad is assigned to – When a valid user/
master code is entered, indicator ARMED and the number [1]... [4] key, indicating the partition that has been disarmed, will light OFF.
Disarm the system
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 222
0
Partitioned system; disarming a different single partition than the keypad is assigned – To disarm a different partition than the
keypad is assigned to, use keypad partition switch feature (by default – disabled; see 23.3. Keypad Partition and Keypad Partition
Switch) before disarming process. Once the partition is swiched and a valid user/master code is entered, indicator ARMED and the number
[1]... [4] key, indicating the partition that has been disarmed, will light OFF.
Use keypad
partition switch
1
2
3
4
5
6
7
8
9
Hold the [1]... [4] key and release it after 3 short beeps:
Value: [1]... [4] key – parition number 1... 4
0
Disarm the system
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 2222
0
Partitioned system; disarming multiple partitions simultaneously – If a user/master code assigned to all 4 partitions exist, user can
disarm all partitions simultaneously. When this feature is used, the system will proceed as follows:
•
if all partitions are armed and a valid user/master code is entered, indicator ARMED along with the number [1], [2], [3] and [4] keys
will light OFF.
•
if a combination of armed and disarmed ready partitions is present, the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and keypad indicator ARMED (if the keypad is switched to a disarmed partition) along with the number
[1]... [4] key, indicating the partition that is to be armed, will light ON. The disarmed-ready partitions will be armed and the pre-armed
ones will be skipped.
•
if one or more partitions are disarmed-unready (keypad number [1]... [4] key flashing, indicating the partition that contains violated
zone/tamper), the system will deny simultaneous partition disarming until the partition’s zone/tamper violation is removed. Alternatively, the user can disarm the partitions one by one (see Partitioned system; arming a different single partition than the
keypad is assigned to above).
Disarm all 4 partitions
simultaneously
1
2
3
4
5
6
7
8
9
0
Hold the [0] key, release it after 3 short beeps and enter user/
master code:
0 uumm
Value: uumm – 4-digit user/master code.
Example: 0 2222
NOTE: To arm/disarm all partitions simultaneously, the user/master code must be assigned to all 4 partitions and the keypad partition switch feature enabled (see 23.3. Keypad Partition and Keypad Partition Switch)..
12.5. EKB3W Keypad and User/Master Code
Illuminated indicator READY on EKB3W keypad indicates that no violated zones and/or tampers are present, therefore the partition is ready
MANUAL ELDES ESIM364 V1.6
EN
49
for arming. If the indicator READY is not illuminated, the partition is unready for arming, therefore the user must restore all violated zones
and/or tampers before arming the partition. Alternatively, the violated zones can be bypassed (see 14.7. Bypassing and Activating
Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes). Indicator SYSTEM will illuminate or flash if system fault (-s) exist (see 29. INDICATION OF SYSTEM FAULTS).
To arm the system by EKB3W keypad, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad
(see 10. MASTER AND USER CODES for user/master code management). By default, the arming process is as follows:
Non-partitioned system/Partitioned system; arming a single partition as the keypad is assigned to – When a valid user/master
code is entered, the system will initiate exit delay, the keypad’s buzzer will emit short beeps and the indicator ARMED will light ON. When
the system is successfully armed, the keypad’s buzzer will silent down.
Arm the system
1
2
3
4
5
6
7
8
9
0
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 2222
Partitioned system; arming a different single partition than the keypad is assigned to – To arm a different partition than the
keypad is assigned to, use keypad partition switch feature (by default – disabled; see 23.3. Keypad Partition and Keypad Partition
Switch) before arming process. Once the partition is swiched and a valid user/master code is entered, the system will initiate exit delay,
the keypad’s buzzer will emit short beeps and the indicator ARMED will light ON. When the system is successfully armed, the keypad’s
buzzer will silent down.
Use keypad
partition switch
1
2
3
4
5
6
7
8
9
Hold the [1]... [4] key and release it after 3 short beeps:
Value: [1]... [4] key – parition number 1... 4
0
Arm the system
1
2
3
4
5
6
7
8
9
0
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code
Example: 2222
The system will arm/disarm the partition corresponding to the one that user/master code (see 23.4. User/Master Code Partition) and
the keypad (see 23.3. Keypad Partition and Keypad Partition Switch) are assigned to. For example, if User code 4 is assigned to
Partition 2, while EKB3W keypad is assigned to Partition 1, the user will be able to arm/disarm only Partition 2 by entering User code 4.
To cancel the arming process, enter the user/master code again during exit delay countdown.
To disarm or turn OFF the alarm, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad. By
default, the system disarming process is as follows:
Non-partitioned system/Partitioned system; disarming a single partition as the keypad is assigned to – When a valid user/master code is
entered, indicator ARMED will light OFF.
Disarm the system
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code.
Example: 2222
0
Partitioned system; disarming a different single partition than the keypad is assigned – To disarm a different partition than the
keypad is assigned to, use keypad partition switch feature (by default – disabled; see 23.3. Keypad Partition and Keypad Partition
Switch) before disarming process. Once the partition is swiched and a valid user/master code is entered, indicator ARMED will light OFF.
Use keypad
partition switch
1
2
3
4
5
6
7
8
9
Hold the [1]... [2] key and release it after 3 short beeps:
Value: [1]... [2] key – parition number 1... 2
0
50
EN
MANUAL ELDES ESIM364 V1.6
Disarm the system
1
2
3
4
5
6
7
8
9
Enter user/master code:
uumm
Value: uumm – 4-digit user/master code.
Example: 2222
0
NOTE: The user can arm/disarm only the first two system partitions using EKB3W keypad.
12.6.iButton Key
To arm or disarm the system, touch the iButton key reader by any of 16 available iButton keys (see 11. iBUTTON KEYS for iButton key management). When the iButton is touched to the iButton key reader for arming, the system will proceed as follows:
•
Non-partitioned system:
•
•
•
If ready (no violated zone/tamper), the system will initiate exit delay and arm.
If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number. In such case the user must restore all violated zones and tampers before arming the system. Alternatively, the
violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and
Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
Partitioned system:
•
•
•
If all partitions are disarmed ready (no violated zone/tamper), the system will initiate exit delay and arm them.
If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and skip the unready one (-s). The system will then send an SMS text message, containing a list of violated
zones/tampers, to user phone number, sharing the same partition (-s) as the iButton key. In such case the user must
restore all violated zones and tampers before arming the system. Alternatively, the violated zones can be bypassed
(see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
If a combination of armed and disarmed ready partitions is present, the system will initiate exit delay, arm the disarmed ready partitions and skip the armed ones.
36
When an iButton key is assigned to multiple partitions, the user will be able arm/disarm the corresponding system partitions
by touching the iButton key to the reader. For example, if iButton 5 is assigned to Partition 1 and 4, the user will be able to arm/
disarm Partition 1 and 4 by touching iButton 5 to the reader. For more details on how to set iButton key partition, please refer
to 23.5. iButton Key Partition.
MANUAL ELDES ESIM364 V1.6
EN
51
12.7. EWK1/EWK2 Wireless Keyfob
EWK1/
EWK2
To arm the system, press 1 of 4 keyfob buttons set to arm the system (by default, EWK1 –
EWK2 button is pressed for arming, the system will proceed as follows:
•
;EWK 2 -
). When EWK1/
Non-partitioned/partitioned system:
•
•
If all partitions are disarmed ready (no violated zone/tamper), the system will initiate exit delay and arm them.
If unready, the system will not arm and provide a list of violated zones/tampers by SMS text message to user phone
number. In such case the user must restore all violated zones and tampers before arming the system. Alternatively, the
violated zones can be bypassed (see 14.7. Bypassing and Activating Zones), disabled (see 14.9. Disabling and
Enabling Zones) or a Force attribute enabled (see 14.6. Zone Attributes).
38
37
Arm the
system
Arm the
system
To disarm the system, press 1 of 4 keyfob buttons set to disarm the system (by default, EWK1 -
).
40
39
Disarm
the
system
; EWK2 -
Disarm
the
system
To verify if the system has been successfully armed, do not release the Arm the system keyfob button and wait for the 3 short
keyfob buzzer’s beeps/indicator’s flashes indicating the successfully carried out command. The long beep/flash indicates the
unsuccessful command.
The system will arm/disarm the partition corresponding to the one that EWK1/EWK2 wireless keyfob is assigned to (see 23.6.
EWK1/ EWK2 Wireless Keyfob Partition). For example, if EWK1/EWK2 wireless keyfob is assigned to Partition 3, the user
will be able to arm/ disarm only Partition 3. To arm a different partition than the EWK1/EWK2 wireless keyfob is assigned to,
bind another EWK1/EWK2 keyfob to the system and assign it to a different partition.
For more details on how to manage EWK1/EWK2 keyfob buttons, please refer to ELDES Configuration Tool software‘s HELP section.
12.8.Arm-Disarm by Zone
ARM/
DISARM
ZONE
The Arm-Disarm by Zone feature allows to use a zone for arming and disarming the alarm system when the zone is violated and
restored. The process is performed by providing a low-level pulse for more than 3 seconds into the specified zone. It means that
violating and restoring the zone leads to system arming and by repeating this action the system becomes disarmed. The system
will arm/disarm the partition (-s) that the zone is assigned to. This method can be set up to 4 pn-board zones
Set zone for ArmDisarm by Zone
method
EKB2
EKB3/
EKB3W
52
EN
Menu path:
OK → iiii → OK → ZONES → OK → ARM/DISARM BY ZONE → OK → ZONE 1... 4 → OK → nn
Value: iiii – 4-digit installer code; nn – on-board zone number, range – [01... 12].
Enter parameter 34, on-board zone slot & zone number:
34 z nn #
Value: z – on-board zone slot for Arm-Disarm by Zone method; range - [1... 4]; nn – on-board
zone number, range – [01... 12].
Example: 34023#
MANUAL ELDES ESIM364 V1.6
Disable Arm-Disarm by
Zone method
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → ZONES → OK → ARM/DISARM BY ZONE → OK → ZONE 1... 4 → OK → 0
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 34, on-board zone slot & parameter status value
Value: z – on-board zone slot for Arm-Disarm by Zone method; range - [1... 4].
Example: 34200#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
12.9.Disabling and Enabling Arm/Disarm Notifications
By default, when the system is successfully armed or disarmed, it replies with confirmation by SMS text message to:
•
user phone number, sharing the same partition as EKB2/EKB3/EKB3W keypad and user/master code, iButton key, EWK1/EWK2 wireless keyfob or zone, set up for Arm/Disarm by Zone method.
•
user phone number that the system arming/disarming by free of charge phone call was initiated from.
•
user phone number that the system arming/disarming by SMS text message was initiated from.
The confirmation SMS text message is sent to the user phone number regarding each partition separately and contains system status and
partition name as well as it may contain a user name assigned to user phone number, user/master code or iButton key. For more details on
names, please refer to 8.1. User Phone Number Names, 10.1. User/Master Code Names and 11.2. iButton Key Names.
To disable/enable this notification for individual user phone number, please refer to the following configuration methods.
Disable arm/disarm
notification
EKB2
Menu path:
System armed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS ARMED EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK →
SMS REPORT → OK → DISABLE → OK
System disarmed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS DISARMED EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → SMS REPORT → OK → DISABLE→ OK
Value: iiii - 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
System armed event
User phone number: 25 01 up 0 #
SMS text message to all users simultaneously: 21 01 up 0 #
SMS delivery report: 55 01 up 0 #
System disarmed event
User phone number: 25 02 up 0 #
SMS text message to all users simultaneously: 21 02 up 0 #
SMS delivery report: 55 02 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2502040#
MANUAL ELDES ESIM364 V1.6
EN
53
Config
Tool
Enable arm/disarm
notification
EKB2
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
System armed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS ARMED EVENT → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK →
SMS REPORT → OK → ENABLE → OK
System disarmed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS DISARMED EVENT → OK → SMS TO ALL → OK → ENBABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → SMS REPORT → OK → ENABLE → OK
Value: iiii - 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
System armed event
User phone number: 25 01 up 1 #
SMS text message to all users simultaneously: 21 01 up 1 #
SMS delivery report: 55 01 up1 #
System disarmed event
User phone number: 25 02 up 1 #
SMS text message to all users simultaneously: 21 02 up 1 #
SMS delivery report: 55 02 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2502061#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
54
EN
MANUAL ELDES ESIM364 V1.6
13.EXIT AND ENTRY DELAY
When arming, the system initiates the exit delay countdown (by default – 15 seconds) intended for the user to leave the secured area. The
exit delay is indicated by short beeps emitted by EKB2/EKB3/EKB3W keypad buzzer and buzzer, connected to the alarm system. When
arming:
•
a non-partitioned system, a countdown timer will be displayed in the home screen view of EKB2 during exit delay.
•
a partitioned system, EKB2 keypad will display ARMING part-name message on the screen for 2 seconds and switch to partition
selection menu during exit delay.
Exit delay is provided when arming the system by the following methods:
•
EKB2/EKB3/EKB3W keypad and user/master code.
•
iButton key.
•
EWK1/EWK2 wireless keyfob.
•
Arm/Disarm by Zone.
To arm the system without exit delay, use one of the following system arming methods:
• Free of charge phone call.
•
SMS text message.
•
EGR100 middle-ware.
Set exit delay
SMS
EKB2
SMS text message content:
ssss_EXITDELAY:p,ext or ssss_EXITDELAY:p,ext;p,ext;p,ext;p,ext
Value: ssss – 4-digit SMS password; p – partition number, range – [1... 4], ext – exit delay
duration, range – [0... 600] seconds.
Example: 1111_EXITDELAY:1,20;3,43
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → EXIT DELAY → OK → PARTITION 1... 4 → OK →
ext → OK
Value: iiii – 4-digit installer code;, ext – exit delay duration, range – [0... 600] seconds.
EKB3W
Enter parameter 72, partition number & exit delay duration:
72 pp ext #
Value: pp – partition number, range – [01... 04], ext – exit delay duration, range – [0... 600]
seconds.
Example: 7203259#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
NOTE: Alternatively, you can set exit delay value to 0 in order to arm the system without exit delay by any available method.
NOTE: EKB3/EKB3W keypad buzzer will only beep if the keypad is operating in the partition where exit delay countdown is in progress.
Once the exit delay has expired, the system initiates the entry delay countdown (by default – 15 seconds) if a Delay type zone is violated.
The countdown is indicated by short beeps emitted by keypad buzzer and by steady beep emitted by system’s buzzer. The indication is intended to advise the user that the system should be disarmed. Once the user presses/touches any key on the keypad during this delay, the
buzzer of the keypad will be silenced. If the system is disarmed before the entry delay expires, no alarm will be caused.
MANUAL ELDES ESIM364 V1.6
EN
55
Set entry delay for
Delay zone
SMS
EKB2
SMS text message content:
ssss_ENTRYDELAY:nn,eeeee or ssss_ENTRYDELAY:nn,eeeee;nn,eeeee;nn,eeeee;nn,eeeee
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 76], eeeee – entry delay
duration, range – [0... 65535] seconds.
Example: 1111_ENTRYDELAY:1,25;54,14;12,20
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → ENTRY DELAY → OK → eeeee → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → ENTRY DELAY → OK → eeeee → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → ENTRY DELAY → OK → eeeee → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17... 32
→ OK → EPGM1 ZONE 1... 32 → OK → ENTRY DELAY → OK → eeeee → OK
Value: iiii – 4-digit installer code; eeeee – entry delay duration, range – [0... 65535] seconds.
EKB3W
Enter parameter 54, partition number and entry delay duration:
54 nn eeeee #
Value: nn – zone number, range – [01... 76], eeeee – entry delay duration, range – [0... 65535]
seconds
Example: 5403259#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
NOTE: Due to battery power saving reasons, EKB3W keypad buzzer will not sound during exit and entry delay if the violated Delay type
zone is not of the associated EKB3W keypad.
For more details on zone types, please refer to 14.5. Zone Type Definitions.
56
EN
MANUAL ELDES ESIM364 V1.6
14.ZONES
Detection devices such as motion detectors and door contacts are connected to the alarm system’s zone terminals. Once connected, the
associated zone’s parameters must be configured.
ESIM364 comes equipped with 6 on-board zones allowing to connect up to 6 detection devices. For more details regarding zone expansion,
please refer to 14.2. Zone Expansion.
ESIM364 zones are classified by 5 categories:
Description
Max. number of
zones per device
Max. number of
zones in total
On-board zones
Built-in wired zones of ESIM364 alarm system.
6/12*
6/12*
Keypad zones
Hardwired zones of EKB2/EKB3 keypad.
1
4
EPGM1 zones
Zones of EPGM1 - hardwired zone & PGM output expansion 16
module.
32
Wireless zones
Non-physical zones automatically created by connected 2**
wireless devices.
64***
Virtual zones
Non-physical zones intended for Panic button feature (alarm 64****
activaton upon pressing the button) on EWK1/EWK2 wireless
keyfob. Virtual zones can be manually created using ELDES
Configuration Tool software.
64****
Zone category
* - 6-Zone mode is enabled by default. ATZ mode doubles the on-board zone number and increases it to 12 in total.
** - Depends on the connected wireless device.
*** - Available only if no zones, EPGM1 zones and virtual zones are present.
**** - Available only if no zones, EPGM1 zones and wireless zones are present.
14.1. Zone Numbering
The zone numbers ranging from Z1 through Z12 are permanently reserved for on-board zones even when ATZ mode is disabled. The
Z13-Z76 zone numbers are automatically assigned in the chronological order to the created virtual zones and the devices connected to the
system: keypads, wireless devices, EPGM1 modules.
14.2. Zone Expansion
For additional detection device connection, the number of zones can be expanded by:
•
enabling the ATZ (Advanced Technology zone) mode (see 14.4. ATZ (Advanced Technology Zone) Mode).
•
connecting EPGM1 hardwired zone and PGM output expansion module (see 32.1.3. EPGM1 – Hardwired Zone & PGM Output Expansion Module).
•
connecting keypads (see 32.1.1. EKB2 – LCD Keypad, 32.1.2. EKB3 – LED Keypad and 33.1. EKB3W – Wireless LED Keypad).
•
binding wireless devices (see 19. WIRELESS DEVICES).
•
creating virtual zones (see ELDES Configuration Tool software’s Help section).
The maximum supported number of zones is 76.
14.3. 6-Zone Mode
By default, ESIM364 alarm system runs in the 6-Zone mode under zone connection Type 1 allowing to connect up to 6 detection devices
of NO (normally-open) type to the on-board zone terminals as indicated in the wiring diagram of Type 1. Once a different zone connection
type is set, the detection device wiring must be done according to the wiring diagram of the associated type. Available zone connection
types for the 6-Zone mode:
•
Type 1 – Parallel wiring of NO (normally-open) detection device with 5,6kΩ EOL (end-of-line) resistor.
•
Type 2 – Serial wiring of NC (normally-closed) detection device with 5,6kΩ EOL resistor.
•
Type 3 – Combination of serial and parallel wiring of tamper with 5,6kΩ EOL resistor and NC (normally-closed) detection device with
3,3kΩ EOL resistor.
For zone wiring diagrams of the 6-Zone mode, please refer to 2.3.2. Zone Connection Types.
MANUAL ELDES ESIM364 V1.6
EN
57
Set zone connection
type for 6-Zone mode
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
OK → iiii → OK → ZONES → OK → ZONE TYPE:6-ZONE M → OK → TYPE 1... 3 → OK
Value: iiii – 4-digit installer code.
Enter parameter 39 & number of zone connection type:
39 1 # – Type 1
39 2 # – Type 2
39 3 # – Type 3
Example: 392#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
14.4.ATZ (Advanced Technology Zone) Mode
The ATZ mode is a software-based feature that doubles the number of on-board zones and enables two detection devices to be installed
per 1 zone terminal. Once this mode is enabled, the zone connection Type 4 is set automatically. The detection devices must be wired to
the on-board zone terminals as indicated in the wiring diagram of the associated zone connection type. Available zone connection types
for the ATZ mode:
•
Type 4 – Parallel wiring of 2 NC (normally-closed) detection devices with 5,6kΩ and 3,3kΩ EOL (end-of-line) resistors respectively.
5,6kΩ EOL resistor corresponds to zones ranging from Z1 through Z6, while 3,3kΩ EOL resistor corresponds to zones ranging from Z7
through Z12.
•
Type 5 – Combination of serial and parallel wiring of tamper with 5,6kΩ EOL resistor and 2 NC (normally-closed) detection devices with
5,6kΩ and 3,3kΩ EOL resistors respectively. 5,6kΩ EOL resistor corresponds to zones ranging from Z1 through Z6, while 3,3kΩ EOL
resistor corresponds to zones ranging from Z7 through Z12.
For zone wiring diagrams of the ATZ mode, please refer to 2.3.2. Zone Connection Types.
Enable ATZ mode
EKB2
EKB3/
EKB3W
Disable ATZ mode
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → ZONES → OK → ATZ MODE → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
Config
Tool
EN
Enter parameter 28 & parameter status value:
28 1 #
Example: 281#
Config
Tool
EKB3/
58
Menu path:
OK → iiii → OK → ZONES → OK → ATZ MODE → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 28 & parameter status value:
28 0 #
Example: 280#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Set zone connection
type for ATZ mode
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
OK → CONFIGURATION → OK → iiii → OK → ZONES → OK → ZONE TYPE:ATZ MODE → OK →
TYPE 4... 5 → OK
Value: iiii – 4-digit installer code.
Enter parameter 38 & number of zone connection type:
38 1 # – Type 4
38 2 # – Type 5
Example: 381#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: The ATZ mode applies to on-board zones only when enabled.
14.5. Zone Type Definitions
•
Interior Follower – The zone can be violated during exit and entry delay without causing an alarm. If the zone is violated before the
entry delay has begun, it will cause an instant alarm followed by single notification delivery even if the zone has been violated multiple
times or another Interrior Follower-type zone has been violated while alarm period (by default - 1 minute) is in progress. The zone is
used where violating a zone during exit/entry delay is unavoidable. Typically, this zone is used for indoor protection devices, such as
motion detectors, installed close to the exit/entry doors.
•
Instant – The alarm is instantly caused if this zone is violated when the system is armed or during entry delay. This zone type is usually
used for doors, windows or other zones, and shock detectors.
•
24-Hour – When the system is either armed or disarmed, the zone will cause instant alarm if violated. Normally, this type of zone is
used for securing the areas that require constant supervisory.
•
Delay – This zone type can be violated during exit and entry delay without causing an alarm. If the zone is violated when the system
is armed, it will initiate entry delay countdown intended for the user to disarm the system. If the zone is left violated after the exit
delay expires, it will cause an instant alarm. If one more zone with Stay-enabled attribute exist and the Delay-type zone is not violated
and restored during exit delay, the system will be armed in Stay mode (see 15. STAY MODE). Typically, this zone type is used for door
contacts installed at designated exit/entry doors.
•
Fire – If this zone type is violated when the system is either armed or disarmed, the alarm will be instantly caused and the siren/bell will
emit pulsating sound. Typically, this zone type is used for flame and smoke detectors.
•
Panic/Silent – This zone operates the same as 24-Hour zone type, but the system will not activate the siren/bell and keypad buzzer if
violated. Normally, this zone type used for panic alarm buttons.
Set zone type for
individual zone
EKB2
EKB3/
EKB3W
MANUAL ELDES ESIM364 V1.6
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12
→ OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24- HOUR | DELAY | FIRE | PANIC/
SILENT → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24-HOUR | DELAY |
FIRE | PANIC/SILENT → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → TYPE → OK → INTERIOR FOLLOWER | INSTANT | 24-HOUR | DELAY | FIRE |
PANIC/SILENT → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → STAY → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 53, zone number & zone type number:
53 nn 1 # – Interior Follower
53 nn 2 # – Instant
53 nn 3 # –24-Hour
53 nn 4 # – Delay
53 nn 5 # – Fire
53 nn 6 # – Panic/Silent
Value: nn – zone number, range – [01... 76]
Example: 53125#
EN
59
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: The system will NOT activate siren/bell and keypad buzzer only when Panic/Silent zone type is violated.
14.6.Zone Attributes
•
Stay – If this attribute is enabled, the zone, regardless of type, will not cause an alarm if violated when the system is Stay armed. For
more details on arming the system in the Stay mode, please refer to 15. STAY MODE.
•
Force – This attribute determines whether the system can be armed or not while a zone is violated. If a zone with the Force attribute
enabled is left violated until the exit delay expires, it will be ignored. Once the system is armed and the zone is restored, the violation
will not be ignored and the zone will operate according to the determined type. For more details on zone types, please refer to 14.5.
Zone Type Definitions.
•
Shared – This attribute determines whether a zone, assigned to multiple partitions, will cause an alarm or not in the associated armed
partition if violated. If a zone with the Shared attribute enabled is violated when at least one of the associated partitions is disarmed,
the alarm will not be caused. Once the system is armed in all of the associated partitions, the zone with Shared attribute enabled will
operate according to the determined type. Typically, this attribute is used for shared areas, such as corridors.
•
Delay, ms – This attribute determines the zone sensitivity level by delay time (By default – 800 milliseconds). If a zone is left triggered
until the delay time expires, the zone is considered violated.
•
Delay becomes Instant in Stay mode – This attribute determines whether or not any Delay type zone will operate as Instant type
zone when the system is armed in the Stay mode. When the system is fully armed, the Delay type zone will operate normally. For more
details on Delay and Instant zone types, please refer to 14.5. Zone Type Definitions.
•
Chime – This feature is used to emit 3 short beeps from the keypad buzzer whenever any Delay type zone is violated while the system
is disarmed. Typically, the feature is used for designated exit/entry doors to indicate the opening of the doors.
NOTE: Due to battery power saving reasons, EKB3W wireless keypad buzzer will not sound if the Bell attribute is not enabled and the violated Delay type zone is not of the associated EKB3W wireless keypad. For more details on EKB3W wireless keypad, please refer to 33.2.1.
EKB3W – Wireless LED Keypad.
Enable Stay attribute
for individual zone
EKB2
EKB3W
Enter parameter 56, zone number & parameter status value:
56 nn 1 #
Value: nn – zone number, range – [01... 76].
Example: 56041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Disable Stay attribute
for individual zone
60
EN
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → STAY → OK → ENABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → STAY → OK → ENABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEPAD
ZONE → OK → STAY → OK → ENABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → STAY → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB2
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → STAY → OK → DISABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → STAY → OK → DISABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → STAY → OK → DISABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → STAY → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
MANUAL ELDES ESIM364 V1.6
EKB3W
Enter parameter 56, zone number & parameter status value:
56 nn 0 #
Value: nn – zone number, range – [01... 76].
Example: 56190#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Enable Force attribute
for individual zone
EKB2
EKB3W
Enter parameter 82, zone number & parameter status value:
82 nn 1 #
Value: nn – zone number, range – [01... 76].
Example: 82061#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Disable Force
attribute for
individual zone
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → FORCE → OK → ENABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → FORCE → OK → ENABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → FORCE → OK → ENABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → FORCE → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB2
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → FORCE → OK → DISABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → FORCE → OK → DISABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → FORCE → OK → DISABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → FORCE → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 82, zone number & parameter status value:
82 nn 0 #
Value: nn – zone number, range – [01... 76].
Example: 82110#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Enable/disable
Shared attribute for
individual zone
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Set Delay, ms atrribute
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
MANUAL ELDES ESIM364 V1.6
EN
61
Enable/disable Delay
becomes Instant in
Stay mode attribute
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Disable Chime
attribute
EKB2
Menu path:
OK →iiii → OK → ZONES → OK → CHIME → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Enable Chime attribute
Enter parameter 32 & parameter status value:
32 0 #
Example: 320#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK →iiii → OK → ZONES → OK → CHIME → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 32 & parameter status value:
32 1 #
Example: 321#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
14.7. Bypassing and Activating Zones
ATTENTION: Zone bypassing and activation must be carried out without Configuration mode being activated by the EKB3/EKB3W keypad.
Zone bypassing allows the user to deactivate a violated zone and arm the system without restoring the zone. If a bypassed zone is violated
or restored during exit/entry delay, or when then system is armed, it will be ignored. When a zone is bypassed, EKB3/EKB3W keypad indicator BYPS will light ON and EKB2 keypad will display
icon in the home screen view.
Bypass individual
violated zone
EKB2
EKB3/
EKB3W
Bypass all violated
zones
EKB2
Menu path:
OK → uumm → OK → BYPASS → OK → BYPASS LIST 1... 5 → OK → Z1-zone-name... Z76zone-name → OK → BYPASS → OK
Value: uumm – 4-digit user/master code; zone-name – up to 24 characters zone name.
Press the [BYPS[ key, enter zone number & user/master code:
BYPS nn uumm #
Value: nn – zone number, range – [01... 76]; uumm – 4-digit user/master code.
Example: BYPS091111#
Menu path:
OK → uumm → OK →BYPASS → OK → BYP VIOLATED ZONES → OK
Value: uumm – 4-digit user/master code.
The zone will stay bypassed until the system is disarmed. Once the system is disarmed, the corresponding zone state will be indicated
on the keypads (see 32.1.1. EKB2 – LCD Keypad, 32.1.2. EKB3 – LED Keypad and 33.1. EKB3W – Wireless LED Keypad) and Info
SMS text message (see 26. SYSTEM INFORMATION. INFO SMS). Alternatively, the user can activate the bypassed zone by the following
configuration methods.
62
EN
MANUAL ELDES ESIM364 V1.6
Activate bypassed
zone
EKB2
EKB3/
EKB3W
Menu path:
OK → uumm → OK → BYPASS → OK → BYPASS LIST 1... 5 → OK → Z1-zone-name... Z76zone-name → OK → UNBYPASS → OK
Value: uumm – 4-digit user/master code; zone-name – up to 24 characters zone name.
Press the [BYPS[ key, enter zone number & user/master code:
BYPS nn uumm #
Value: nn – zone number, range – [01... 76]; uumm – 4-digit user/master code.
Example: BYPS251111#
NOTE: Zones can only be bypassed and activated when the system is not armed.
14.8.Zone Names
Each zone has a name that can be customized by the user. Typically, the name specifies a device type connected to a determined zone
terminal, for Example: Kitchen doors opened. The zone names are used in SMS text messages that are sent to the user during alarm. the
By default, the zone names are: Z1 – Zone1, Z2 – Zone2, Z3 – Zone3, Z4 – Zone4 etc.
Set zone name
SMS
Config
Tool
View zone names
SMS
EKB2
Config
Tool
SMS text message content:
ssss_Znn:zone-name
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 76]; zone-name – up to
24 characters zone name.
Example: 1111_Z3:Door sensor triggered
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → NAME
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → NAME
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → NAME
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → NAME
Value: iiii – 4-digit installer code.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Colon, semi-colon characters, parameter names and/or values, such as PSW, STATUS, ON, OFF etc. are NOT allowed in zone
names
NOTE: Multiple zone names can be set by a single SMS text message, Example: 1111_Z1:Kitchen doors opened;Z3:Movement in basement;Z4:Bedroom window opened
MANUAL ELDES ESIM364 V1.6
EN
63
14.9.Disabling and Enabling Zones
By default, all zones, except keypad and virtual zones, are enabled. To permanently disable/enable an individual zone, please refer to the
following configuration methods.
Disable zone
SMS
EKB2
Enter parameter 52, zone number & parameter status value:
52 nn 0 #
Value: nn – zone number, range – [01... 76].
Example: 52360#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
EKB2
EN
SMS text message content:
ssss_Znn:ON
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 76].
Example: 1111_Z6:ON
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → STATUS → OK → ENABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → STATUS → OK → ENABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → STATUS → ENABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → STATUS → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 52, zone number & parameter status value:
52 nn 1 #
Value: nn – zone number, range – [01... 76].
Example: 52151#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
64
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → STATUS → OK → DISABLE → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → STATUS → OK → DISABLE → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → STATUS → DISABLE → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → STATUS → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
EKB3/
Enable zone
SMS text message content:
ssss_Znn:OFF
Value: ssss – 4-digit SMS password; nn – zone number, range – [1... 76].
Example: 1111_Z13:OFF
MANUAL ELDES ESIM364 V1.6
15.STAY MODE
Stay mode allows the user to arm and disarm the alarm system without leaving the secured area. If the zones with Stay attribute enabled
are violated when the system is Stay armed, no alarm will be caused. Typically, this feature is used when arming the system at home before
going to bed.
The system can be Stay armed under the following conditions:
•
If a zone with Stay attribute enabled is NOT violated during exit delay, the system will arm in Stay mode. When arming the system in
Stay mode under this condition, one of the available arming methods must be used that provide exit delay. For more details on these
methods, please refer to 13. EXIT AND ENTRY DELAY.
•
The system will instantly arm in Stay mode when using one of the following methods.
Arm the system in
Stay mode
EKB2
EKB3/
EKB3W
Menu path:
Non-partitioned system: P2 → uumm → OK
Partitioned system: P2 → uumm → OK → [p] part-name → OK
Value: uumm – 4-digit user/master code; p – partition number, range – [1... 4]; part-name – up
to 15 characters partition name.
Press the [STAY] key & enter user/master:
STAY uumm
Value: uumm – 4-digit user/master code.
Example: STAY1111
When one or more system partitions are successfully armed in Stay mode, EKB2 keypad will display
icon in the home screen view.
NOTE for EKB3/EKB3W: System arming in Stay mode by the keypad must be carried out without Configuration mode being activated.
NOTE: The system can be armed in Stay mode, only if there is at least one zone with Stay attribute enabled.
NOTE: Stay mode is not supported by virtual zones.
For more details on how to enable Stay attribute for zone, please refer to 14.6. Zone Attributes.
MANUAL ELDES ESIM364 V1.6
EN
65
16.TAMPERS
The tamper circuit is a single closed loop such that a break in the loop at any point will cause a tamper alarm regardless of the system
status – armed or disarmed. During the tamper alarm, the system will activate the siren/bell and the keypad buzzer and send the SMS text
message to the preset user phone number. The system will cause tamper alarm under the following conditions:
•
If the enclosure of a detection device, siren/bell, metal cabinet or keypad is opened, the physical tamper switch will be triggered. By
default, indicated as Tamper x in the SMS text message (x = tamper number).
•
If the wireless signal is lost due to low signal level or low battery power on a certain wireless device and does not restore during 1 hour
period. This event is identified as Wireless Signal Loss. By default, indicated as No wireless signal from wless-dev wless-id Tamper x in
the SMS text message (wless-dev = wireless device model; wless-id = 8-digit wireless device ID code; x = tamper number).
By default, tamper alarm notification by SMS text message is enabled. To disable/enable tamper alarm notification, please refer to the
following configuration methods.
Disable tamper alarm
notification
EKB2
Menu path:
Tamper alarm
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TAMPER ALARM → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
SMS REPORT → OK → DISABLE → OK
Wireless signal loss
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
WLESS SIGN LOSS EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
Tamper alarm
User phone number: 25 13 up 0 #
SMS text message to all users simultaneously: 21 13 up 0 #
SMS delivery report: 55 13 up 0 #
Wireless signal loss
User phone number: 25 18 up 0 #
SMS text message to all users simultaneously: 21 18 up 0 #
SMS delivery report: 55 18 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2518031#
Config
Tool
66
EN
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Enable tamper alarm
notification
EKB2
Menu path:
Tamper alarm
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TAMPER ALARM → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
SMS REPORT → OK → ENABLE → OK
Wireless signal loss
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
WLESS SIGN LOSS EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
Tamper alarm
User phone number: 25 13 up 1 #
SMS text message to all users simultaneously: 21 13 up 1 #
SMS delivery report: 55 13 up 1 #
Wireless signal loss
User phone number: 25 18 up 1 #
SMS text message to all users simultaneously: 21 18 up 1 #
SMS delivery report: 55 18 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2513041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how to view violated tamper, please refer to 17. ALARM INDICATIONS AND NOTIFICATIONS
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following feature:
•
System arming is blocked if any system fault exists. The user will not be able to arm the system until all existing system faults are solved.
•
System arming is blocked until tamper fault is cleared by the installer.
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please refer to 36. EN
50131-1 GRADE 3.
16.1. Tamper Names
Each tamper has a name that can be customized by the user. The tamper names are used in SMS text messages that are sent to the user
during the tamper alarm. By default, the tamper names are: Tamper 1, Tamper 2, Tamper 3, Tamper 4 etc. To set a different tamper name,
please refer to the following configuration methods.
Manage tamper name
MANUAL ELDES ESIM364 V1.6
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
67
17.ALARM INDICATIONS AND NOTIFICATIONS
When a zone, depending on zone type (see 14.5. Zone Type Definitions), or tamper is violated, the system will cause an alarm. By default, the alarm duration is 1 minute (see 20. SIREN/BELL regarding the alarm duration). During the alarm, the system will follow this
pattern:
1. The system activates the siren/bell and the keypad buzzer.
a) The siren/bell will emit pulsating sound if the violated zone is of Fire type, otherwise the sound will be steady.
b) The keypad buzzer will emit short beeps.
c) EKB2 keypad will display
icon next to the alarmed partition in the home screen view followed by
icon indicating the presence
of the alarm events in the alarm log (see 28. EVENT AND ALARM LOG). In case a Fire-type zone is violated in any system partition,
icon will appear in the home screen view.
d) EKB3 keypad operating in 4-partition mode will flash the [1]... [4] key corresponding to the alarmed partition number.
e) If one or more zones are violated, EKB3/EKB3W will light ON the corresponding violated zone indicator (-s) ranging from 1 through
12. Indicator SYSTEM will flash if one or more high-numbered zones are violated. If one or tampers are violated, indicator SYSTEM will
light ON. For more details on viewing violated high-numbered zone and tamper numbers by EKB3/EKB3W keypad, please refer to 29.
INDICATION OF SYSTEM FAULTS.
2. The system attempts to send an SMS text message, containing the violated zone/tamper name (see 14.8. Zone Names on how to set
a zone name), to the first preset user phone number, sharing the same partition as the violated zone/tamper. The system will send SMS
text messages regarding each violated zone/tamper separately.
a) If the user phone number is unavailable and the system fails to receive the SMS delivery report during 20 seconds, it will attempt to
send the SMS text message to the next preset user phone number, assigned to the same partition as the previous one. The user phone
number may be unavailable due to the following reasons:
•
mobile phone was switched off.
•
was out of GSM signal coverage.
b) By default, the system will continue sending the SMS text message to the next preset user phone numbers in the priority order until
one is available. The system sends the SMS text message only once and will not return to the first user phone number if the last one
was unavailable.
3. By default, the system attempts to ring the first user phone number via GSM, sharing the same partition as the violated zone/tamper. The
system will dial regarding each violated zone/tamper separately.
a) When the call is answered, the system will shut down the siren/bell and play the audio file that can be listened to on the user’s mobile
phone. This feature will be available only if an audio file is recorded and assigned to the violated zone (see 17.2. Audio Files).
b) When the audio record has played, the user will be able to listen on the mobile phone for approx. 30 seconds to what is happening in the
area, surrounding the alarm system. This feature will be available only if a microphone is connected to the system (see 25. REMOTE
LISTENING AND 2-WAY VOICE COMMUNICATION).
c) The system will dial the next preset user phone number, assigned to the same partition, if the previous user was unavailable due to the
following reasons:
• mobile phone was switched off.
• mobile phone was out of GSM signal coverage.
• provided “busy” signal.
• user did not answer the call after several rings, predetermined by the GSM operator.
d) The system will continue dialing the next preset user phone numbers in the priority order until one is available. The system will dial the
user phone number 5 times if the first user phone number was out of GSM signal coverage/switched OFF, otherwise the system will dial
only once. If the system ends up with all unsuccessful to contact any preset user phone number, will stop dialing and will not return to
the first user phone number.
e) The system will not dial the next preset user phone number if the previous one was available, but rejected the phone call.
4. If enabled, the system attempts to ring the first phone number via PSTN (see 30.2.3. PSTN). The system will dial regarding each violated
zone/tamper separately.
a) When the call is answered, the system will automatically drop the call.
b) The system will dial the next preset phone number if the previous one was unavailable due to the following reasons:
• mobile phone was switched off.
• mobile phone was out of GSM signal coverage.
• provided “busy” signal.
• user did not answer the call after several rings, predetermined by the GSM operator.
c) The system will continue dialing the next preset phone numbers in the priority order until one is available. The system will dial the
phone number 5 times (by default) if the first phone number was unavailable. If the system ends up with all unsuccessful to contact
any preset phone number, it will return to the first phone number.
To silent the siren/bell as well as to cease system phone calls and SMS text message sending to the user phone numbers, please disarm the
system (see 12. ARMING AND DISARMING).
68
EN
MANUAL ELDES ESIM364 V1.6
ATTENTION: The wireless siren EWS1/EWS2/EWS3 will sound only if wireless zone of the siren is assigned to the same partition as the one
that has been alarmed (see 23.1. Zone Partition).
View violated zones
SMS
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
EKB2
Menu path:
OK → uumm → OK → VIOLATED ZONES → OK → ZONE 1... 76
Value: uumm – 4-digit user/master code.
EKB3W
Please, refer to illuminated zone indicators ranging from 1 through 12 on the keypad. The
flashing indicator SYSTEM stands for violated high-numbered zones (Z13-Z76). For more
details on violated high-numbered zone indication, please refer to 29. INDICATION OF SYSTEM FAULTS.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
The systemwill automatically send an SMS text message, containing a violated tamper name,
to user phone number.
EKB2
Menu path:
OK → uumm → OK → VIOLATED TAMPERS → OK → TAMPER 1... 76
Value: uumm – 4-digit user/master code.
EKB3/
View violated tampers
EKB3/
EKB3W
The illuminated indicator SYSTEM stands for system fault presence including violated tamper. For more details on violated tamper indication, please refer to 29. INDICATION OF SYSTEM FAULTS.
For more details details on how to disable/enable SMS text messages and phone calls to preset user phone number in case of alarm, please
refer to 17.1. Enabling and Disabling Alarm Notifications
ATTENTION: Phone calls to the preset user phone number in case of alarm are disabled by force when MS mode is enabled (see
30. Monitoring Station).
NOTE: If one or more zones/tampers are violated during the alarm, the system will attempt to send as many SMS text message and dial the
user phone number as many times as the zone/tamper was violated.
NOTE: If the system sent the SMS text message and/or dialed the user phone number after disarming the system, it means that the SMS
text message and/or phone call was queued up in the memory before the system was disarmed
17.1. Enabling and Disabling Alarm Notifications
By, default the system will ring the preset user phone numbers via GSM in case of alarm. To disable/enable this feature, please refer to the
following configuration methods.
Disable call in case
of alarm
EKB2
EKB3/
EKB3W
MANUAL ELDES ESIM364 V1.6
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → CALL IN CASE
ALARM → OK → GSM USER 1... 10 → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 30, user phone number slot & parameter status value:
30 us 1 #
Value: us - user phone number slot, range - [01... 10].
Example: 30081#
EN
69
Config
Tool
Enable call in
case of alarm
EKB2
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → CALL IN CASE
ALARM → OK → GSM USER 1... 10 → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 30, user phone number slot & parameter status value:
30 us 0 #
Value: us - user phone number slot, range - [01... 10].
Example: 30090#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
By, default the system will send SMS text message to preset user phone numbers in case of alarm. To disable/enable this feature, please
refer to the following configuration methods.
Disable SMS text
message in case of
alarm
EKB2
EKB3/
EKB3W
Config
Tool
Enable SMS text
message in case of
alarm
EKB2
EKB3/
EKB3W
Config
Tool
70
EN
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
GENERAL ALARM → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM → OK →
SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 03 up 0 #
SMS text message to all users simultaneously: 21 03 up 0 #
SMS delivery report: 55 03 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2503060#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: User phone number: OK → iiii → OK → SMS
MESSAGES 1 → OK → GENERAL ALARM → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK →
GENERAL ALARM → OK → SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 03 up 1 #
SMS text message to all users simultaneously: 21 03 up 1 #
SMS delivery report: 55 03 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2503101#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
By, default the system will not ring the preset phone number via PSTN in case of alarm. To manage this feature, please refer to 30.2.3.
PSTN)
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
By default, tamper alarm notification by SMS text message is enabled. For more details on how to disable/enable tamper alarm notification,
please refer to 16. TAMPERS.
ATTENTION: Regardles of the Call in Case of Alarm parameter status, the system will NOT ring the preset user phone number via GSM if
the system is connected to the monitoring station (see 30. MONITORING STATION) and/or when Smart Security feature is in use (see 37.
SMART SECURITY).
17.2. Audio Files
The system comes equipped with a feature allowing to record up to 16 audio files of up to 6 seconds length using the microphone of the PC.
The recorded file can be assigned to any system zone, except virtual zone, and be played when the alarm is caused by zone with an audio file
assigned. This feature will be available only if the system is able to dial user phone number in the event of an alarm and the user answers
the call. The supported audio file format is as follows:
• Max. number of audio files: up to 16
• Max. audio length: up to 6 seconds
• File format: .wav
• Specifications: 8,000 kHz; 8 Bit; Mono
Record and manage
audio files
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Assign audio file to
individual zone
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Single audio file can be assigned to multiple zones.
MANUAL ELDES ESIM364 V1.6
EN
71
18.PROGRAMMABLE (PGM) OUTPUTS
A PGM output is a programmable output that toggles to its set up state when a specific event has occurred in the system, the scheduled
weekday and time has come or if the user has initiated the PGM output state change manually. Normally, PGM outputs can be used to open/
close garage doors, activate lights, heating, watering and much more. When a PGM output turns ON, the system triggers any device or relay
connected to it.
ESIM364 comes equipped with four open-collector PGM outputs allowing to connect up to four devices or relays. For more details on PGM
output expanding, please refer to 18.2. PGM Output Expansion.
ESIM364 PGM outputs are classified by 4 categories:
PGM output category
Description
Max. number of PGM
outputs per device
Max. number of PGM
outputs in total
On-board PGM Outputs
Built-in wired PGM outputs of ESIM364 alarm system.
4
4
EPGM8 PGM Outputs
PGM outputs of EPGM8 - hardwired PGM output expan8
sion module.
8
EPGM1 PGM Outputs
PGM outputs of EPGM1 - hardwired zone & PGM output
2
expansion module.
4
Wireless PGM Outputs
Non-physical PGM outputs automatically created by con2*
nected wireless devices.
64**
* - Depends on the connected wireless device.
** - Available only if no EPGM1 PGM outputs are present.
For PGM output wiring diagram, please refer to 2.3.6. Relay Finder® 40.61.9.12 with Terminal Socket 95.85.3.
18.1. PGM Output Numbering
The PGM output numbers ranging from C1 through C12 are permanently reserved for on-board PGM outputs even if EPGM8 module mode is
disabled. The C13-C76 PGM output number are automatically assigned in the chronological order to the devices connected to the system:
EPGM1 modules and wireless devices.
18.2.PGM Output Expansion
For additional electrical appliance connection, the number of PGM outputs can be expanded by:
•
connecting EPGM8 hardwired PGM output expansion module. (see 18.2.1. EPGM8 Mode and 32.3.1. EPGM8 – Hardwired PGM
Output Expansion Module)
•
connecting EPGM1 hardwired zone and PGM output expansion module (see 32.1.3. EPGM1 – Hardwired Zone & PGM Output Expansion Module).
•
binding the wireless devices (see 19. WIRELESS DEVICES).
The maximum supported PGM output number is 76.
18.2.1. EPGM8 Mode
EPGM8 is an expansion module, which expands the system with 8 additional hardwired PGM outputs. For more details on EPGM8 module
installation, please refer to 32.3.1. EPGM8 – Hardwired PGM Output Expansion Module.
Once the EPGM8 module is installed, the EPGM8 mode must be enabled.
Enable EPGM8 mode
EKB2
EKB3/
EKB3W
Config
Tool
72
EN
Menu path:
OK → iiii → OK → PGM OUTPUTS → OK → USING EPGM8 → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 33 & parameter status value:
33 1 #
Example: 331#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Disable EPGM8 mode
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
OK → iiii → OK → PGM OUTPUTS → OK → USING EPGM8 → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 33 & parameter status value:
33 0 #
Example: 330#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
18.3.PGM Output Names
Each PGM output has a name that can be customized by the user. Typically, the name specifies a device type connected to a determined
PGM output, for Example: Lights. The name can be used instead of PGM output number when controlling the PGM output by SMS text
message. By default, the PGM output names are: C1 – Controll1, C2 – Controll2, C3 – Controll3, C4 – Controll4 etc.
Set PGM output name
SMS
Config
Tool
View PGM output
names
SMS
EKB2
Config
Tool
SMS text message content:
ssss_Coo:out-name
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name –
up to 16 characters PGM output name.
Example: 1111_C2:Lights
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_STATUS
Value: ssss – 4-digit SMS password.
Example: 1111_STATUS
Menu path:
On-board PGM output: OK → iiii → OK → PGM OUTPUTS → OK → ONBOARD OUTPUTS → OK
→ OUTPUT 1... 12 → OK → NAME
Wireless PGM output: OK → iiii → OK → PGM OUTPUTS → OK → WIRELESS OUTPUTS 1... 4 →
OK → OUTPUT 13... 76 → OK → NAME
Value: iiii – 4-digit installer code.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Space, colon, semi-colon characters, parameter names and/or values, such as PSW, STATUS, ON, OFF etc. are NOT allowed in
PGM output names.
18.4.Turning PGM Outputs ON and OFF
By default, all PGM outputs are turned OFF. To instantly turn ON/OFF an individual PGM output and set its state to ON/OFF when the system
starts-up, please refer to the following configuration methods.
Turn ON PGM output/
Set PGM output startup state as ON
MANUAL ELDES ESIM364 V1.6
SMS
SMS text message content:
ssss_Coo:ON or ssss_out-name:ON
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name –
up to 16 characters PGM output name.
Example: 1111_Lights:ON
EN
73
EKB2
EKB3W
Enter parameter 61, PGM output number & parameter status value:
61 oo 1 #
Value: oo – PGM output number, range – [01... 76].
Example: 61031#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
EWK1/
EWK2/
EWK2A
Turn OFF PGM output/
Set PGM output startup state as OFF
Menu path:
On-board PGM output: OK → iiii → OK → PGM OUTPUTS → OK → ONBOARD OUTPUTS → OK
→ OUTPUT 1... 12 → OK → STATUS → OK → ENABLE → OK
Wireless PGM output: OK → iiii → OK → PGM OUTPUTS → OK → WIRELESS OUTPUTS 1... 4 →
OK → OUTPUT 13... 76 → OK → STATUS → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
SMS
EKB2
This operation may be carried out from the wireless keyfob if pre-configured using the PC running ELDES Configuration Tool software.
SMS text message content:
ssss_Coo:OFF or ssss_out-name:OFF
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name –
up to 16 characters PGM output name.
Example: 1111_C2:OFF
Menu path:
On-board PGM output: OK → iiii → OK → PGM OUTPUTS → OK → ONBOARD OUTPUTS → OK
→ OUTPUT 1... 12 → OK → STATUS → OK → DISABLE → OK
Wireless PGM output: OK → iiii → OK → PGM OUTPUTS → OK → WIRELESS OUTPUTS 1... 4 →
OK → OUTPUT 13... 76 → OK → STATUS → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 61, PGM output number & parameter status value:
61 oo 0 #
Value: oo – PGM output number, range – [01... 76].
Example: 61020#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
EWK1/
EWK2/
EWK2A
This operation may be carried out from the wireless keyfob if pre-configured using the PC running ELDES Configuration Tool software.
To instantly turn ON an individual PGM output for a determined time period and automatically turn it OFF when the time period expires,
please refer to the following configuration method.
Turn ON PGM output
for time period
74
EN
SMS
SMS text message content:
ssss_Coo:ON:hr.mm.sc or ssss_out-name:ON:hr.mn.sc
Value: ssss – 4-digit SMS password; oo – PGM output number, range – [1... 76]; out-name
– up to 16 characters PGM output name; hr – hours, range – [00... 23]; mn – minutes, range
– [00... 59]; sc – seconds, range – [00... 59].
Example: 1111_C4:ON:10.15.35
MANUAL ELDES ESIM364 V1.6
To instantly turn OFF an individual PGM output for a determined time period and automatically turn it ON when the time period expires,
please refer to the following configuration method.
Turn OFF PGM output
for time period
SMS
SMS text message content:
ssss_Coo:OFF:00.00.sc or ssss_out-name:OFF:hr.mn.sc
Value: ssss – 4-digit SMS password;oo – PGM output number, range – [1... 76]; out-name
– up to 16 characters PGM output name; hr – hours, range – [00... 23]; mn – minutes, range
– [00... 59]; sc – seconds, range – [00... 59].
Example: 1111_Lights:OFF:00.00.23
When the PGM output is turned ON or OFF, the system will send a confirmation by SMS text message to the user phone number that the
SMS text message was sent from.
NOTE: PGM output can be turned ON for a determined time period only when it is in OFF state
NOTE: PGM output can be turned OFF for a determined time period only when it is in ON state
NOTE: Multiple PGM outputs can be turned ON/OFF by a single SMS text message, Example: 1111_C1:ON C2:OFF Pump:ON C4:ON:00.20.25
18.5.PGM Output Control by Event and Scheduler
The PGM outputs can automatically operate when a specific event occurs in the system and/or when the scheduled weekday and time
comes.
PGM Output Actions
The automatic action of the determined PGM output can be set as follows:
•
Turn ON – Determines whether the PGM output is to be turned ON.
•
Turn OFF – Determines whether the PGM output is to be turned OFF.
•
Pulse – Determines whether the PGM output is to be turned ON for a set period of time in seconds.
System Events
The aforementioned PGM output action can be automatically carried out under the following events that have occurred in the system:
•
System armed – System is armed in a determined partition ranging from Partition 1 through 4 or any partition.
•
System disarmed – System is disarmed in a determined partition ranging from Partition 1 through 4 or any partition.
•
Alarm begins – Alarm begins in a determined partition ranging from Partition 1 through 4 or any partition.
•
Alarm stops – Alarm stops in a determined partition ranging from Partition 1 through 4 or any partition.
•
Temperature falls – Temperature falls below the set MIN value of a determined temperature sensor 1-8.
•
Temperature rises – Temperature rises above the set MAX value of a determined temperature sensor 1-8.
•
Zone violated – A determined zone ranging from Z1 through Z76 is violated.
•
Zone restored – A determined zone ranging from Z1 through Z76 is restored.
•
Scheduler starts – Determines Start Time of a selected scheduler 1-16.
•
Scheduler ends – Determines End Time of a selected scheduler 1-16.
The user can also set a custom text, which will be sent by SMS text message to user phone number when the automatic PGM output action
is carried out.
Schedulers
The system supports up to 16 schedulers that allow the PGM outputs to operate according to the day of the week and time. When the
scheduler, which includes the set weekday and time, is selected, the PGM output will operate according to it. Each scheduler includes the
following parameters:
•
Always – The scheduler is not in use.
•
At specified time – Determines whether weekday and time settings are enabled:
•
Start Time – Determines the point in time when the PGM output action can begin.
•
End Time – Determines the point in time when the PGM output action can complete.
•
On weekdays – Determines days in week when the PGM output action is valid.
Additional Conditions
Additional condition narrows down the chances for a determined automatic PGM output operation to be carried out. If this feature is enabled, the PGM output will become dependent on one more system event that must be occurred prior or must occur after the aforemen-
MANUAL ELDES ESIM364 V1.6
EN
75
tioned system event. The PGM output will not operate until the chain of system events meets the set values:
•
System armed – System is armed in a determined partition ranging from 1 to 4 or any partition.
•
System disarmed – System is disarmed in a determined partition ranging from 1 to 4 or any partition.
•
Zone violated – A determined zone ranging from Z1 to 76 is violated.
•
Zone restored – A determined zone ranging from Z1 to Z76 is restored.
Example: PGM output C1 is set to be turned ON when zone Z6 is violated. The additional condition feature is enabled and set to allow this
action to be carried out only if system’s Partition 2 is disarmed. It means that the PGM output C1 will be turned ON when zone Z6 is violated,
but only if system’s Partition 2 is disarmed.
Manage PGM output
control by event &
scheduler
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: When both - a system event is determined and a scheduler is selected, the PGM output will operate only if the determined event has
occurred in the system during the scheduled time period.
ATTENTION: If the date and time are not set, the system will NOT be able to automatically control the PGM outputs. For more details on how
to set date and time, please refer to 9. DATE AND TIME.
18.6.Wireless PGM Output Type Definitions
•
Output – Operates as normal PGM output that can be controlled by the user or automatically by event and scheduler. Normally, this
type is used for any device or relay.
•
Siren – Operates as siren output that automatically activates during alarm. Typically, this type is used for bell/siren connected to EW1
wireless device.
Set output type for
individual wireless
PGM output
76
EN
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
19.WIRELESS DEVICES
ESIM364 system has a built-in wireless module for system extension capabilities. The wireless module easily allows the user to bind up to
32 ELDES-made wireless devices to the system. This includes the following:
•
EWP1 – wireless PIR sensor (motion detector).
•
EWD1 – wireless magnetic door contact.
•
EWD2 - magnetic door contact/shock sensor
•
EWS1 and EWS3 – wireless indoor sirens.
•
EWS2 – wireless outdoor siren.
•
EWK1 and EWK2 – wireless keyfobs.
•
EKB3W – wireless keypad.
•
EW1 – wireless zone and PGM output expansion module.
•
EW1B – wireless battery-powered zone and PGM output expansion module.
•
EWF1 - wireless smoke detector.
The wireless devices can operate at a range of up to 30 meters from the alarm system unit while inside the building and at up to 150 meters
range in open areas. The wireless connection is two-way and operates in one of four available channels at 868 Mhz (EU version) / 915
Mhz (US version) non-licensed frequency range. The communication link between the wireless device and the alarm system is constantly
supervised by a configurable self-test period, identified as Test Time.
For more details on how to install the wireless devices, please refer to 33. ELDES WIRELESS DEVICES and RADIO SYSTEM INSTALLATION AND SIGNAL PENETRATION manual located at www.eldes.lt/download
19.1. Binding, Removing and Replacing Wireless Devicess
When the wireless device is switched ON, it will initiate the data transmission to the system within its wireless connection range. In order
to optimize battery power saving of the wireless device, the data transmission periods vary by itself while the device is switched ON, but
still unbound. The data transmission period from the system wireless devices when the alarm system is switched OFF or if the wireless
device is unbound or removed is as follows:
•
•
EKB3W, EW1, EW1B, EWP1, EWS1, EWS2, EWS3, EWF1:
•
First 360 attempts after the device startup (reset) - every 10 seconds.
•
The rest of attempts - every 1 minute.
EWD1, EWD2:
•
First 360 attempts after the device startup (reset) - every 10 seconds.
•
The rest of attempts - every 2 minutes.
Once the wireless device is bound, it will attempt to exchange data with ESIM364 system. Due to battery saving reasons, all ELDES wireless
devices operate in sleep mode. The data exchange will occur instantly if the wireless device is triggered (zone alarm or tamper alarm) or periodically when the wireless device wakes up to transmit the supervision signal, identified as Test Time, to the system as well as to accept
the queued up command (if any) from the system. Example: The alarm occurred at 09:15:25 and the system queued up the command for
EWS2 siren to start sounding. By default, Test Time value of EWS2 siren is 7 seconds, therefore EWS2 siren will sound at 09:15:32.
By default, the Test Time period is as follows:
• EKB3W, EWD1: every 60 seconds.
•
EW1, EWP1, EWF1, EWD2: every 30 seconds.
•
EW1B: every 20 seconds.
•
EWS1, EWS2, EWS3: every 7 seconds.
To set a different Test Time value, please refer to the following configuration method.
Set Test Time
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Test Time affects the wireless device binding process due to the alarm system listening for the incoming data from the wireless
device. The system binds the wireless device only when the first data packet is received.
NOTE FOR EKB3W: In comparison with other ELDES wireless devices, EKB3W keypad features some exceptions regarding the wireless
communication. For more details on EKB3W keypad wireless communication and back-light timeout, please refer to 33.1.7. Wireless
Communication, Sleep Mode and Back-light Timeout.
MANUAL ELDES ESIM364 V1.6
EN
77
An 8-digit wireless device ID code will be required in order to bind the device to the system or to remove it from the system. The wireless
ID code is printed on a label, which can be located on the inner or outer side of the enclosure or on the printed circuit board (PCB) of the
wireless device.
To bind a wireless device, please refer to the following configuration methods.
Bind wireless device
to the system
SMS
Config
Tool
SMS text message content:
ssss_SET:wless-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code.
Example: 1111_SET:535185D
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE FOR EWK1/EWK2/EKB3W: When binding EWK1/EWK2 wireless keyfob or EKB3W wireless keypad, it is necessary to press several
times any button/key on the device.
Once a wireless device is bound, it occupies one of 32 available wireless device slots and the system adds one or two wireless zones and
wireless PGM outputs depending on the wireless device model.
To remove a wireless device, please refer to the following configuration methods.
Remove wireless
device from the
system
SMS
Config
Tool
SMS text message content:
ssss_DEL:wless-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code.
Example: 1111_DEL:535185D
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Once a wireless device is removed from the system, please restore its default parameters and remove the batteries from it.
To replace an existing wireless device with a new same model device, please refer to the following configuration methods
Replace wireless
device
SMS
Config
Tool
SMS text message content:
ssss_REP:wless-id<oldwl-id
Value: ssss – 4-digit SMS password; wless-id – 8-digit wireless device ID code of the old device; oldwl-id - 8-digit wireless device ID code of the new device.
Example: 1111_REP:535185D<41286652
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When a wireless device is successfully replaced with a new one, the configuration of the old wireless device remains.
NOTE: If you are unable to bind a wireless device, please restore the wireless device’s parameters to default and try again. For more details
on how to restore the default parameters, please refer to the user manual provided along with the wireless device or visit www.eldes.lt/en/
download to download the latest user manual
ATTENTION: In order to correctly remove the wireless device from the system, the user must remove the device using SMS text message
or ELDES Configuration Tool software and restore the parameters of the wireless device to default afterwards. If only one of these actions
is carried out, the wireless device and the system will attempt to exchange data to keep the wireless connection alive. This leads to fast
battery power drain on the battery-powered wireless device.
19.2.Wireless Device Information and Signal Status Monitoring
Once a wireless device is bound, the user can view the following information of a determined wireless device:
• Battery level (expressed in percentage).
• Wireless signal strength (expressed in percentage).
• Error rate (number of failed data transmission attempts in 10-minute period) - indicated only in EKB2 keypad menu.
• Firmware version.
• Test Time period (expressed in milliseconds) - indicated only in SMS text message reply.
78
EN
MANUAL ELDES ESIM364 V1.6
To view the wireless device information, please refer to the following configuration methods.
View wireless device
information
SMS
EKB2
Config
Tool
SMS text message content:
ssss_RFINFO:wless-id or ssss_RFINFO:Znn
Value: wless-id – 8-digit wireless device ID code; nn – wireless zone number, range – [13...
76].
Example: 1111_RFINFO:535185D
Menu path:
Battery level: OK → iiii → OK → WIRELESS DEVICES 1... 2→ OK → wless-dev wless-id → OK
→ BATTERY
Wireless signal: OK → iiii → OK → WIRELESS DEVICES 1... 2→ OK → wless-dev wless-id → OK
→ SIGNAL
Error rate: OK → iiii → OK → WIRELESS DEVICES 1... 2→ OK → wless-dev wless-id → OK →
ERROR RATE
Firmware version: OK → iiii → OK → WIRELESS DEVICES 1... 2→ OK → wless-dev wless-id →
OK → FW RELEASE
Value: iiii – 4-digit installer code; wless-dev – wireless device model; wless-id – 8-digit
wireless device ID code.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The system supports up to 32 wireless devices. To view the number of unoccupied wireless device slots in the system, please refer to the
following configuration methods
View unoccupied
wireless device slots
SMS
Config
Tool
SMS text message content:
ssss_STATUS_FREE
Example: 1111_STATUS_FREE
This operation may be carried out from the PC using the ELDES Configuration Tool software.
When the wireless signal between the system and a wireless device is lost and does not restore during 1 hour period, the system will send
notification by SMS text message to preset user phone number. By default, the notification regarding the wireless signal status is enabled.
To disable/enable this notification, please refer to 16. TAMPERS.
MANUAL ELDES ESIM364 V1.6
EN
79
19.3.Disabling and Enabling Siren if Wireless Signal is Lost
If a wireless device loses its wireless signal for 1 hour or longer, the system will send notification by SMS text message to user phone number and activate the siren/bell. By default, the siren will not be activated when wireless signal is lost. To enable/disable this feature, please
refer to the following configuration methods.
Enable Siren if
Wireless Signal is Lost
EKB2
EKB3/
EKB3W
Config
Tool
Disable Siren if
Wireless Signal is Lost
EKB2
EKB3/
EKB3W
Config
Tool
80
EN
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → SIREN SETTINGS →OK → SRN IF WLESS LOSS
→ OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 76 & parameter status value:
76 1 #
Example: 761#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → SIREN SETTINGS →OK → SRN IF WLESS LOSS
→ OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 76 & parameter status value:
76 0 #
Example: 760#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
20.SIREN/BELL
When the system is in alarm state, the siren/bell will sound until the set time (By default – 1 minute) expires or until the system is disarmed.
To set the alarm duration, please refer to the following configuration methods.
Set alarm duration
SMS
SMS text message content:
ssss_SIREN:t
Value: ssss – 4-digit SMS password; t – alarm duration, range – [0... 5] minutes.
Example: 1111_SIREN:4
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → ALARM DURATION
→ OK → tt → OK
Value: iiii – 4-digit installer code; tt – alarm duration, range – [1... 10] minutes.
EKB3W
Enter parameter 10 & alarm duration:
10 tt #
Value: tt – alarm duration, range – [00... 10] minutes.
Example: 1007#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
View alarm duration
SMS
SMS text message content:
ssss_SIREN
Value: ssss – 4-digit SMS password
Example: 1111_SIREN
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → ALARM DURATION
Value: iiii – 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For siren/bell wiring diagram, please refer to 2.3.3. Siren.
NOTE: 0 value disables the siren/bell.
NOTE: Due to battery power saving reasons, the wireless siren will sound for 1 minute regardless of the set alarm duration time, unless it is
set to 0.
MANUAL ELDES ESIM364 V1.6
EN
81
20.1.BELL Output Status Monitoring
The system constantly supervises the BELL output. If the siren/bell is disconnected/cut-off, the system will instantly send the notification
by SMS text message to User 1 and indicate system fault condition on the keypad (see 29. INDICATION OF SYSTEM FAULTS). Once the
bell/siren is connected/fixed, the system will notify User 1 by SMS text message and the keypad will no longer indicate system fault.
By default, the notification by SMS text message regarding the BELL output status is disabled. To enable/disable this notification, please
refer to the following configuration methods.
Enable Siren Fail/
Restore notification
EKB2
EKB3/
EKB3W
Config
Tool
Disable Siren Fail/
Restore notification
EKB2
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SIREN FAIL/REST EV → OK → SMS TO ALL → OK → ENABLE → OK
MS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK →
SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 08 up 1 #
SMS text message to all users simultaneously: 21 08 up 1 #
SMS delivery report: 55 08 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2508021#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SIREN FAIL/REST EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 08 up 0 #
SMS text message to all users simultaneously: 21 08 up 0 #
SMS delivery report: 55 08 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2508040#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
20.2.Bell Squawk
If enabled, the siren/bell indicates the completed system arming and disarming process. After the system is successfully armed, the siren/
bell will emit 2 short beeps and 1 long beep after the system is disarmed. To enable/disable the Bell Squawk feature, please refer to the
following configuration methods.
Enable Bell Squawk
82
EN
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → BELL SQUAWK → OK
→ ENABLE → OK
Value: iiii – 4-digit installer code.
MANUAL ELDES ESIM364 V1.6
EKB3/
EKB3W
Disable Bell Squawk
Enter parameter 29 & parameter status value:
29 1 #
Example: 291#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → BELL SQUAWK → OK
→ DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 29 & parameter statusvalue:
29 0 #
Example: 290#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
20.3.Bell Squawk in Stay Mode
If enabled, the Bell Squawk will be available when arming/disarming the system in Stay mode (see 15. STAY MODE). To enable/disable this
feature, please refer to the following configuration methods
Enable Bell Squawk
in Stay Mode
EKB2
EKB3/
EKB3W
Config
Tool
MANUAL ELDES ESIM364 V1.6
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → BELL SQUAWK STAY
→ OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 95 & parameter status value:
95 1 #
Value: 951#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
83
Disable Bell Squawk
in Stay Mode
EKB2
EKB3/
EKB3W
Config
Tool
84
EN
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → BELL SQUAWK STAY
→ OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 95 & parameter status value:
95 0 #
Value: 950#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
20.4.Indication by EWS2 Indicators
When enabled, the built-in LED indicators of EWS2 wireless outdoor siren will flash during the alarm. To enable/disable this feature, please
refer to the following configuration methods.
Enable EWS2 LED
indication
EKB2
EKB3/
EKB3W
Disable EWS2 LED
indication
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → EWS2 LED → OK →
ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 29 & parameter status value:
88 1 #
Example: 881#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → EWS2 LED → OK →
DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 29 & parameter status value:
88 0 #
Example: 880#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
20.5.Indication by EWS3 Indicators
When enabled, the built-in LED indicators of EWS3 wireless indoor siren will flash during the alarm. In the event of burglary, 24-hour or
tamper alarm, EWS3 will flash the blue LED indicators, while in case of a fire alarm, the device can flash the red LED indicator. To enable/
disable these features, please refer to the following configuration methods.
Enable EWS3 LED
indication
EKB2
EKB3W
Enter parameter 94/93 & parameter status value:
Burglary/24-hour/tamper alarm LED: 93 1 #
Fire alarm LED: 93 1 #
Example: 931#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Disable EWS3 LED
indication
EKB2
EKB3/
EKB3W
MANUAL ELDES ESIM364 V1.6
Menu path:
Burglary/24-hour/tamper alarm LED: OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN
SETTINGS → OK → EWS3 ALARM LED → OK → ENABLE → OK
Fire alarm LED: OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK →
EWS3 FIRE LED → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Menu path:
Burglary/24-hour/tamper alarm LED: OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN
SETTINGS → OK → EWS3 ALARM → OK → DISABLE → OK
Fire alarm LED: OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK →
EWS3 FIRE LED → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 94/93 & parameter status value:
Burglary/24-hour/tamper alarm LED: 93 0 #
Fire alarm LED: 93 0 #
Example: 940#
EN
85
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
20.6.EWF1 Interconnection
The interconnection feature automatically links all wireless smoke detectors to each other that are connected to the same alarm system
unit. When any EWF1 detects smoke, it sounds the alarm and sends the signal to the alarm system that causes an instant alarm along with
the rest of EWF1 wireless smoke detectors. The device that detected smoke will auto-reset when the smoke clears, while the rest of EWF1
detectors will sound in accordance with the set time period (by default - 30 seconds).
By default, the interconnection feature is enabled and the siren alarm duration is 30 seconds. To manage these parameters, please refer
to the following configuraiton methods.
Disable
interconnection
EKB2
EKB3/
EKB3W
Config
Tool
Enable
interconnection
EKB2
EKB3/
EKB3W
Config
Tool
Set EWF1 siren alarm
duration
Config
Tool
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → EWF1 SIREN
INTERC. → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 50 & parameter status value:
50 0 #
Example: 500#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → SIREN SETTINGS → OK → EWF1 SIREN
INTERC. → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 29 & parameter status value:
50 1 #
Example: 501#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on EWF1 wireless smoke detector, please refer to 33.9. EWF1 - Wireless Smoke Detector
86
EN
MANUAL ELDES ESIM364 V1.6
21.BACKUP BATTERY, MAINS POWER SUPPLY STATUS MONITORING AND MEMORY
The system may come equipped with a backup battery maintaining power supply of the system when the mains power supply is temporally
lost. The implemented feature allows the system to perform a self-test on the backup battery and notify User 1 by SMS text message as
well as to indicate system fault by the keypad (see 29. INDICATION OF SYSTEM FAULTS) if:
•
battery has failed and requires replacement – battery resistance is 2Ω or higher; self-tested every 24 hours.
•
battery is dead or missing – battery is not present or battery voltage is below 5V; self-tested every 1 minute.
•
battery power is running low – battery voltage is 10.5V or lower; constantly self-tested.
By default, all notifications regarding the backup battery status are enabled. To disable/enable a determined backup battery notification,
please refer to the following configuration methods.
Disable Battery Failed
notification
EKB2
EKB3/
EKB3W
Config
Tool
Enable Battery Failed
notification
EKB2
EKB3/
EKB3W
Config
Tool
Disable Battery Dead
or Missing notification
MANUAL ELDES ESIM364 V1.6
EKB2
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY FAILED → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 05 up 0 #
SMS text message to all users simultaneously: 21 05 up 0 #
SMS delivery report: 55 05 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2105010#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY FAILED → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 05 up 1 #
SMS text message to all users simultaneously: 21 05 up 1 #
SMS delivery report: 55 05 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2505031#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY DEAD/MISS → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EN
87
EKB3/
EKB3W
Config
Tool
Enable Battery Dead
or Missing notification
EKB2
EKB3/
EKB3W
Config
Tool
Disable Low Battery
notification
EKB2
EKB3/
EKB3W
Config
Tool
Enable Low Battery
notification
88
EN
EKB2
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 06 up 0 #
SMS text message to all users simultaneously: 21 06 up 0 #
SMS delivery report: 55 06 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 5506070#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY DEAD/MISS → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 06 up 1 #
SMS text message to all users simultaneously: 21 06 up 1 #
SMS delivery report: 55 06 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 5506101#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
LOW BATTERY → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY → OK → SMS
REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 07 up 0 #
SMS text message to all users simultaneously: 21 07 up 0 #
SMS delivery report: 55 07 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2107100#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
LOW BATTERY → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY → OK → SMS
REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
MANUAL ELDES ESIM364 V1.6
EKB3/
EKB3W
Config
Tool
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 07 up 1 #
SMS text message to all users simultaneously: 21 07 up 1 #
SMS delivery report: 55 07 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2107021#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If the household electricity is unstable in the system installation area, the system may temporally lose its power supply and continue operating on the backup battery power. The system supervises the mains power supply and notifies User 1 by SMS text message as well as
indicates system fault condition on the keypad (see 29. INDICATION OF SYSTEM FAULTS) when the mains power is lost. When the mains
power restores, the system will notify User 1 by SMS text message and the keypad will no longer indicate system fault.
By default, system notification by SMS text message regarding mains power supply status is enabled. To disable/enable this notification,
please refer to the following configuration methods.
Disable mains power
supply loss/restore
notification
EKB2
EKB3/
EKB3W
Config
Tool
Enable mains power
supply loss/restore
notification
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R → OK →
GSM USER 1... 10 → OK → DISBLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
MAIN POWER L/R → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R → OK →
SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 04 us 0 #
SMS text message to all users simultaneously: 21 04 us 0 #
SMS delivery report: 55 04 us 0 #
Value: us - user phone number slot, range - [01... 10].
Example: 2504050#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
MAIN POWER L/R → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R → OK →
SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 04 up 1 #
SMS text message to all users simultaneously: 21 04 up 1 #
SMS delivery report: 55 04 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2514091#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, mains power supply loss and restore delay are 30 and 120 seconds respectively. To set a different mains power supply loss and
restore delay duration, please refer to the following configuration methods.
MANUAL ELDES ESIM364 V1.6
EN
89
Set mains power
supply loss delay
EKB2
EKB3W
Enter parameter 70 & loss delay duration:
70 lllll #
Value: lllll – mains power loss delay duration, range - [0... 65535] seconds.
Example: 7043#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Set mains power
supply restore delay
Menu path:
OK → iii → OK → PRIMARY SETT INGS → OK → MAIN POWER STATUS → OK → LOSS DELAY →
OK → lllll → OK
Value: iiii – 4-digit installer code; lllll – mains power loss delay duration, range - [0... 65535]
seconds.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → MAIN POWER STATUS → OK → RESTORE
DELAY → OK → rrrrr → OK
Value: iiii – 4-digit installer code; w – mains power restore delay duration, range - [0...
65535] seconds.
EKB3W
Enter parameter 71 & restore delay duration:
71 rrrrr #
Value: rrrrr – mains power restore delay duration, range - [0... 65535] seconds.
Example: 71150#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
The configuration settings and event log records are stored in a built-in EEPROM memory, therefore even if the system is fully shut down,
the configuration and event log remain. For more details regarding the event log, please refer to 28. EVENT AND ALARM LOG.
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
NOTE: In order to view the backup battery voltage, resistance, mains power supply status and value, please refer to Diagnostic Management
feature available on ELDES Configuration Tool software.
90
EN
MANUAL ELDES ESIM364 V1.6
22.GSM CONNECTION AND ANTENNA STATUS MONITORING
The system supervises the GSM connection every 10 minutes. When the GSM signal is lost, the system indicator NETW will light OFF, the
GSM modem automatically restarts, the keypad will indicate system fault condition (see 29. INDICATION OF SYSTEM FAULTS) and the
system will turn ON a determined PGM output if the GSM signal is lost for a longer time period than the set delay value (By default – 180
seconds). Once the GSM signal restores, the sys­tem will notify User 1 by SMS text message, the keypad will no longer indicate system fault
and the determined PGM output will turn OFF.
By default, the notifications by SMS text message regarding GSM signal loss is disabled. To enable/disable thus notification, please refer to
the following configuration methods.
Enable GSM
Connection Failed
notification
EKB2
EKB3/
EKB3W
Config
Tool
Disable GSM
Connection Failed
notification
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED →
OK → GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 11 up 1 #
SMS text message to all users simultaneously: 21 11 up 1 #
SMS delivery report: 55 11 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2114091#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED →
OK → GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 11 up 0 #
SMS text message to all users simultaneously: 21 11 up 0 #
SMS delivery report: 55 11 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2114020#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, the PGM output for GSM signal loss indication is not set. To set the PGM output and delay duration for GSM signal loss indication,
please refer to the following configuration method.
Manage GSM signal
loss indication by PGM
output
MANUAL ELDES ESIM364 V1.6
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
91
The system constantly monitors the GSM/GPRS antenna status. If the GSM/GPRS antenna is disconnected/cut-off, the system will send
notification by SMS text message to User 1 and the keypad will indicate system fault condition (see 29. INDICATION OF SYSTEM FAULTS)
. Once the antenna is connected/fixed, the system will notify User 1 by SMS text message and the keypad will no longer indicate system
fault.
By default, the notification by SMS text message regarding the GSM/GPRS antenna status is disabled. To enable/disable this notification,
please refer to the following configuration methods.
Enable GSM/GPRS
Antenna Fail/Restore
notification
EKB2
EKB3/
EKB3W
Config
Tool
Disable GSM/GPRS
Antenna Fail/Restore
notification
EKB2
EKB3/
EKB3W
Config
Tool
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM ANT FAIL/REST → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 12 us 1 #
SMS text message to all users simultaneously: 21 11 us 1 #
SMS delivery report: 55 11 us 1 #
Value: us - user phone number slot, range - [01... 10].
Example: 2512031#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM ANT FAIL/REST → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
User phone number: 25 12 us 0 #
SMS text message to all users simultaneously: 21 11 us 0 #
SMS delivery report: 55 11 us 0 #
Value: us - user phone number slot, range - [01... 10].
Example: 2512030#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
92
EN
MANUAL ELDES ESIM364 V1.6
23.PARTITIONS
ESIM364 system comes equipped with a partitioning feature that can divide the alarm system into four independently controlled areas identified as Partition 1 through 4, which are all supervised by one alarm system unit. Partitioning can be used in installations where
shared alarm system is more practical, such as a house and a garage or within a single multi-storey building. When partitioned, each system
element, like zone, user phone number, keypad, user/master code, iButton key and wireless keyfob can be assigned to single or multiple
partitions. The user will then be able to arm/disarm the system partition (-s) that the zones and arm/disarm method, except EKB2 keypad,
are assigned to.
The following table reflects the values used for system element assignment to partitions by EKB2/EKB3/EKB3W keypad. A sum of values is
used to assign the element to multiple partitions.
Partition
Partition 1
Partition 2
Partition 3
Partition 4
Value
1
2
4
8
Example1: The user wants to assign a certain iButton key to Partition 4 only. According to the table value 8
reflects Partition 4. He would then have to enter value 8.
Example2: The user wants to assign a certain user code to Partition 2 and 3. According to the table value 2 reflects Partition 2, while value 4 reflects Partition 3, therefore 2 + 4 = 6. He would then have to enter value 6.
Example3: The user wants to assign a certain zone to Partition 1, 3 and 4. According to the table value 1 reflects Partition 1, while values 4 and 8 reflect Partitions 3 and 4 respectively, therefore 1 + 4 + 8 = 13. He
would then have to enter value 13.
23.1. Zone
Partition
Zone partition determines which system partition (-s) the zone will operate in.
Set zone partition
EKB2
Menu path:
On-board zone: OK → iiii → OK → ZONES → OK → ONBOARD ZONES → OK → ZONE 1... 12 →
OK → PARTITION → OK → pv → OK
Wireless zone: OK → iiii → OK → ZONES → OK → WIRELESS ZONES 1... 4 → OK → WIRELESS
ZONE 13... 76 → OK → PARTITION → OK → pv → OK
Keypad zone: OK → iiii → OK → ZONES → OK → KEYPAD ZONES → OK → 1ST... 4TH KEYPAD
ZONE → OK → PARTITION → OK → pv → OK
EPGM1 zone: OK → iiii → OK → ZONES → OK → EPGM1 ZONES 1-16... EPGM1 ZONES 17-32 →
OK → EPGM1 ZONE 1... 32 → OK → PARTITION → OK → pv → OK
Value: iiii – 4-digit installer code; pv – partition value (see 23. PARTITIONS).
EKB3W
Enter parameter 57, zone number & partition value:
57 nn pv #
Value: nn – zone number, range – [01... 76]; pv – partition value (see 23. PARTITIONS).
Example: 57032#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
ATTENTION: Wireless siren EWS1/EWS2/EWS3 siren will sound only if wireless zone of the siren is assigned to the same partition as the
one that has been alarmed.
23.2.User Phone Number Partition
User phone number partition determines which system partition (-s) can be armed/disarmed from a certain user phone number by dialing
system’s phone number or sending an SMS text message.
Set user phone
number partition
EKB2
EKB3W
Enter parameter 59, user phone number slot & partition value:
59 us pv #
Value: us – user phone number slot, range – [01... 10]; pv – partition value (see 23. PARTITIONS).
Example: 591013#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
MANUAL ELDES ESIM364 V1.6
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → CALL/SMS SETTINGS → OK → USERS → OK →
GSM USER 1... 10 → OK → PARTITION → pv → OK
Value: iiii – 4-digit installer code; pv – partition value (see 23. PARTITIONS).
EN
93
23.3.Keypad Partition and Keypad Partition Switch
Keypad partition determines which system partition the keypad will operate in. To identify which partition the keypad is operating in:
•
EKB2 – Refer to partition name (by default – PART1) indicated in home screen view.
•
EKB3W/EKB3 (2-partition mode) – Refer to the location of the illuminated indicator READY on the keypad. The indicator will be illuminated under section A or B, which represent Partition 1 and Partition 2 respectively.
EKB3 keypad can operate in the following modes:
•
2-partition mode – This parameter determines whether EKB3 keypad can operate only in one of the first two system partitions allowing to arm/disarm them and switch the keypad partition using [1]... [2] keys. This mode is set up by default.
•
4-partition mode – This parameter determines whether EKB3 keypad can operate in one of the four system partitions allowing to
arm/disarm them, indicate arm/disarm status, zone state on [1]... [4] keys (see 32.1.2. EKB3 - LED Keypad) and switch the keypad
partition using [1]... [4] keys.
The keypad must be assigned to the same partition as the user/master code (see 23.4. User/Master Code Partition) in order to arm/
disarm the system by the keypad. For more details on system arming/disarming by the keypad, please refer to 12.3. EKB2 Keypad and
User/Master Code, 12.4. EKB3 Keypad and User/Master Code and 12.5. EKB3W Keypad and User/Master Code..
Set EKB3 partition
mode as 2-partition or
4-partition
Config
Tool
Set keypad partition
EKB2
EKB3/
EKB3W
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
EKB2 partition: OK → iiii → OK → PRIMARY SETTINGS → OK → KEYPAD PARTITION → OK →
KEYPAD PARTITION → OK → [k] EKB2 → OK → PARTITION 1... 4 → OK → DISABLE | ENABLE → OK
EKB3 partition: OK → iiii → OK → PRIMARY SETTINGS → OK → KEYPAD PARTITION → OK →
KEYPAD PARTITION → OK → [k] EKB3→ OK → PARTITION 1... 4 → OK
EKB3W partition: OK → iiii → OK → PRIMARY SETTINGS → OK → KEYPAD PARTITION → OK →
EKB3W PARTITION → OK → EKB3W wless-id → OK → PARTITION 1... 2 → OK
Value: iiii – 4-digit installer code; k – keypad slot, range – [1... 4]; wless-id – 8-digit wireless
device ID code.
Enter parameter 51, keypad slot & partition number:
EKB3 partition: 51 kk p #
EKB3W partition: 51 kw r #
Value: kk – EKB3 keypad slot, range – [01... 04]; kw – EB3W keypad slot, range – [05... 08];
p – EKB3 partition number, range – [1... 4]; r – EKB3W partition number, range – [1... 2].
Example: 51062#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: 4-partition mode must be enabled in order to assign EKB3 keypad to Partition 3 or Partition 4.
NOTE: EKB2 keypad can be assigned to multiple partitions, while EKB3 keypad can only be assigned only to single partition.
NOTE: EKB3W keypad assignment is restricted to Partition 1 and Partition 2.
NOTE: The slots for EKB3W keypads are automatically assigned to the bound keypad in the chronological order, hence the earliest bound
keypad would acquire slot 5, while the latest bound keypad would acquire slot 8.
Keypad partition switch allows to quickly change the EKB3/EKB3W keypad partition. When the keypad partition is changed and when 1
minute after the last key-stroke/key-touch expires, the system will return to the preset keypad partition. Typically, this feature is used
for viewing arm/ disarm status and alarms of a different partition or when arming/disarming a different system partition by EKB3/EKB3W
keypad than the keypad is assigned to.
By default, keypad partition switch is disabled. To enable/disable this feature, please refer to the following configuration methods.
94
EN
MANUAL ELDES ESIM364 V1.6
Enable keypad
partition switch
EKB2
EKB3/
EKB3W
Disable keypad
partition switch
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → KEYPAD PARTITION → OK → PARTITION
SWITCH → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
Enter parameter 77 & parameter status value:
77 1#
Example: 771#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → KEYPAD PARTITION → OK → PARTITION
SWITCH → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 77 & parameter status value:
77 0 #
Example: 770#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Keypad partition switch can only be used when the system is partitioned.
23.4. User/Master Code Partition
User/master code partition determines which system partition (-s) can be armed/disarm using a certain user/master code. User/master
code must be assigned to the same partition as the keypad (see 23.3. Keypad Partition and Keypad Partition Switch) in order to arm/
disarm the system by EKB2/EKB3/EKB3W keypad . For more details on system arming/disarming by the keypad, please refer to 12.3. EKB2
Keypad and User/Master Code, 12.4. EKB3 Keypad and User/Master Code and 12.5. EKB3W Keypad and User/Master Code.
Set user/master
code partition
EKB2
EKB3/
EKB3W
Config
Tool
Master code: OK → mmmm → OK → CODES → OK → MASTER CODE → OK → PARTITION → OK
→ pv → OK
User code 2... 17: OK → mmmm → OK → CODES → OK → USER CODE (2-17) → OK → USER
CODE 2... 17 → OK → PARTITION → OK → pv → OK
User code 18... 30: OK → mmmm → OK → CODES → OK → USER CODE (18-30) → OK → USER
CODE 18... 30 → OK → PARTITION → OK → pv → OK
Value: mmmm – 4-digit master code; pv – partition value (see 23. PARTITIONS).
Press [CODE], [5], 01/user code slot & enter master code:
Master code: [CODE] [5] 01 pv mmmm #
User code: [CODE] [5] us pv mmmm #
Value: us - user code slot, range - [02... 30]; pv – partition value (see 23. PARTITIONS);
mmmm - 4-digit master code.
Example: CODE50481111#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE for EKB3/EKB3W: User/master code partition management must be carried out using master code and without Configuration mode
being activated.
MANUAL ELDES ESIM364 V1.6
EN
95
23.5.iButton Key Partition
iButton key partition determines which system partition (-s) can be armed/disarmed using a certain key. iButton key must be assigned to
the partition (-s) that the user desires to arm. For more details on system arming/disarming by iButton key, please refer to 12.5. iButton
Key.
Set iButton key
partition
EKB2
Menu path:
OK → iiii → OK → IBUTTON KEYS → OK → IBUTTON → OK → IBUTTON 1... 16 → OK →
PARTITION → OK → pv → OK
Value: iiii – 4-digit installer code; pv – partition value (see 23. PARTITIONS).
EKB3W
Enter parameter 60, iButton key slot & partition value:
60 is pv #
Value: is – iButton key slot, range – [01... 16]; pv – partition value (see 23. PARTITIONS).
Example: 600511#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
23.6.EWK1/EWK2 Wireless Keyfob Partition
EWK1/EWK2 wireless keyfob partition determines which system partition can be armed/disarmed using a certain EWK1/EWK2 wireless
keyfob. For more details on system arming/disarming by EWK1/EWK2 wireless keyfob, please refer to 12.6. EWK1/EWK2 Wireless Keyfob.
Set EWK1/EWK2
partition
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: EWK1/EWK2 wireless keyfob can only be assigned to one partition.
96
EN
MANUAL ELDES ESIM364 V1.6
24.TEMPERATURE SENSORS
The system may be equipped with up to 8 temperature sensors intended for temperature measurement in the surrounding areas. This
feature allows to monitor the temperature of up to 8 different areas in real-time and receive a notification by SMS text message to User 1
phone number when the set temperature boundaries are exceeded. The temperature is measured at 0,5 degree centigrade (C) accuracy
and automatically rounded to the higher value when 0,5 or above, e. g. temperature ranging from 23,5 through 24,4 will be treated as 24 C.
24.1.Adding, Removing and Replacing Temperature Sensors
To add a temperature sensor to the system, do the following:
a) Shutdown the system.
b) Wire up the temperature sensor to the 1-Wire interface terminals (see 2.3.5. Temperature Sensor and iButton Key Reader for
temperature sensor wiring diagram).
c) If more than one temperature sensor is required, wire another sensor in parallel to the previous one.
d) By default, the first added temperature sensor will be identified as primary and the second one – as secondary temperature sensor
(see 24.2. Primary and Secondary Temperature Sensors).
e) Add as many temperature sensors as necessary – wire up one after another in parallel – until the number of 8 sensors is reached.
f) Power up the system.
To view the real-time temperature values measured by each temperature sensor, please refer to the following configuration methods.
View real-time
temperature values
of individual
temperature sensor
View real-time
temperature values
of all temperature
sensors
SMS
SMS text message content:
ssss_ITEMP:ts
Value: ssss – 4-digit SMS password; ts – temperature sensor slot, range - [1... 8].
Example: 1111_ITEMP:4
EKB2
Menu path:
OK → uumm → OK → TEMP SENSORS INFO → OK → 1. tm.p C (PRIM) | (SEC)... 8. tm.p C
Value: uumm - 4-digit user/master code; tm.p – real-time temperature value.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_ITEMP:?
Value: ssss – 4-digit SMS password.
Example: 1111_ITEMP:?
EKB2
Menu path:
OK → uumm → OK → TEMP SENSORS INFO → OK → 1. tm.p C (PRIM) | (SEC)... 8. tm.p C
Value: uumm - 4-digit user/master code; tm.p – real-time temperature value.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
If a temperature sensor is faulty, it is recommended to remove it or replace it by a functional sensor.
Remove/replace
individual
temperature sensor
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: When multiple temperature sensors are connected, please touch and hold the sensor with your fingers and watch the temperature
value change to identify the number of the temperature sensor slot.
MANUAL ELDES ESIM364 V1.6
EN
97
24.2.Primary and Secondary Temperature Sensors
By default, the first added temperature sensor is automatically set as primary, while the second one is set as secondary temperature sensor. The real-time temperature values of the primary and secondary temperature sensors are included in the Info SMS text message (see
26. SYSTEM INFORMATION. INFO SMS) as well as the temperature measured by the primary temperature sensor is indicated in the
home screen view of EKB2 keypad.
To set a different temperature sensor as primary or secondary, please refer to the following configuration methods.
Set primary
temperature sensor
SMS
SMS text message content:
ssss_TEMPI:PRIM:ts
Value: ssss – 4-digit SMS password; ts – temperature sensor slot, range - [1... 8].
Example: 1111_TEMPI:PRIM:4
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → PRIMARY TEMP SENS
→ OK → 1... 8 CONNECTED → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 89 & temperature sensor slot:
89 ts #
Value: ts – temperature sensor slot, range - [01... 08].
Example: 8903#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Set secondary
temperature sensor
SMS
SMS text message content:
ssss_TEMPI:SEC:ts
Value: ssss – 4-digit SMS password; ts – temperature sensor slot, range - [1... 8].
Example: 1111_TEMPI:SEC:3
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → SECOND. TEMP SENS
→ OK → 1... 8 CONNECTED → OK
Value: iiii – 4-digit installer code.
EKB3W
Enter parameter 90 & temperature sensor slot:
90 ts #
Value: ts – temperature sensor slot, range - [01... 08].
Example: 9005#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
To view the slot number of primary and secondary temperature sensors, please refer to the following configuration methods.
View primary and
secondary temperature
sensor slot number
98
EN
SMS
SMS text message content:
ssss_TEMPI:?
Value: ssss – 4-digit SMS password.
Example: 1111_TEMPI:?
EKB2
Menu path:
Primary: OK → uumm → OK → TEMP SENSORS INFO → OK → 1... 8 tm.p C (PRIM)
Secondary: OK → uumm → OK → EMP SENSORS INFO → OK → 1... 8 tm.p C (SEC)
Value: uumm - 4-digit user/master code; tm.p – real-time temperature value.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
View primary and
secondary temperature
sensor real-time
temperature values
SMS
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
EKB2
Menu path:
Primary: OK → uumm → OK → TEMP SENSORS INFO → OK → 1... 8 tm.p C (PRIM)
Secondary: OK → uumm → OK → EMP SENSORS INFO → OK → 1... 8 tm.p C (SEC)
Value: uumm - 4-digit user/master code; tm.p – real-time temperature value.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Primary and secondary temperature sensors can be set by a single SMS text message, Example: 1111_TEMPI:PRIM:4,SEC:3
24.3.Setting Up MIN and MAX Temperature Boundaries. Temperature Info SMS
The system supports an SMS text message identified as the Temperature Info SMS, which is automatically delivered to User 1 phone num­
ber if the preset minimum (MIN) or maximum (MAX) temperature boundary of any temperature sensor is exceeded by at least 1 C.
To set the MIN and MAX temperature boundaries for a certain temperature sensor, please refer to the configuration methods.
Set MIN and MAX
temperature
boundaries
SMS
EKB2
EKB3/
EKB3W
Config
Tool
View MIN and
MAX temperature
boundaries
SMS
EKB2
MANUAL ELDES ESIM364 V1.6
SMS text message content:
ssss_TEMPts:MIN:mnn,MAX:mxx
Value: ssss – 4-digit SMS password; ts - temperature sensor slot, range – [1... 8]; mnn – MIN
boundary, range – [-55... 125] C; mxx - MAX boundary, range – [-55... 125] C.
Example: 1111_TEMP2:MIN:-5,MAX:28
Menu path:
MIN: OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → TEMPERATURE
SENS 1... 8 → OK → TEMP. MIN → OK → mnn → OK
MAX: OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → TEMPERATURE
SENS 1... 8 → OK → TEMP. MAX → OK → mxx → OK
Value: iiii – 4-digit installer code; mnn – MIN boundary, range – [-55... 125] C; mxx - MAX
boundary, range – [-55... 125] C.
Keys P1 or P2 are used to enter minus character, e.g. -20.
Enter parameter 19 & temperature Value:
19 ts mnn mxx #
Value: ts - temperature sensor slot, range – [1... 8]; mnn – MIN boundary, range – [-55...
125] C; mxx - MAX boundary, range – [-55... 125] C. 00 value stands for minus character, e.
g. 0020 = -20
Example: 1906001530#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_TEMPts
Value: ssss – 4-digit SMS password; ts - temperature sensor slot, range – [1... 8].
Example: 1111_TEMP4
Menu path:
MIN: OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → TEMPERATURE
SENS 1... 8 → OK → TEMP. MIN
MAX: OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → TEMPERATURE
SENS 1... 8 → OK → TEMP. MAX
Value: iiii – 4-digit installer code
EN
99
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details on how Send SMS text message to all users simultaneously and SMS delivery report parameters affect the SMS text message transmission, please refer to 27. SYSTEM NOTIFICATIONS.
NOTE: MIN and MAX boundaries can also be set separately by multiple SMS text messages, Example: 1111_TEMP1:MIN:6 and 1111_
TEMP1:MAX:40
24.4.Temperature Sensor Names
The temperature sensor name is included in the Temperature Info SMS when delivered to the User 1 phone number. This feature allows
easier identification of the temperature sensor and normally it is used when monitoring temperature changes in different areas.
Set temperature
sensor name
SMS
Config
Tool
View temperature
sensor name
Delete temperature
sensor name
EN
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_TEMPts
Value: ssss – 4-digit SMS password; ts - temperature sensor slot, range – [1... 8].
Example: 1111_TEMP3
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → TEMP SENSORS → OK → TEMPERATURE SENS
1... 8 → OK → NAME
Value: iiii – 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
Config
Tool
100
SMS text message content:
ssss_TEMPts:NAME:temp-sens-name
Value: ssss – 4-digit SMS password; ts – temperature sensor slot, range – [1... 8]; tempsens-name – 4 to 24 characters temperature sensor name.
Example: 1111_TEMP3:NAME:Warehouse
SMS text message content:
ssss_TEMPts:NAME:
Value: ssss – 4-digit SMS password; ts - temperature sensor slot, range – [1... 8].
Example: 1111_TEMP2:NAME:
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
25.REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION
ESIM364 comes equipped with a microphone that allows the user to listen on his mobile phone to what is happening in the secured area.
By installing one of the audio modules EA1 or EA2, the user will be able to have a 2-way voice communication (see 32.3.2. EA1 – Audio
Output Module and 32.3.3. EA2 – Audio Output Module with Amplifier). Remote listening and 2-way voice communication can
operate under the following conditions:
•
The system makes a phone call via GSM to a preset user phone number in case of alarm and the user answers the call.
•
The user initiates remote listening by sending the SMS text message, the system makes a phone call via GSM to the user phone number
that the SMS text message was sent from and the user answers the call.
Initiate remote
listening
SMS
SMS text message content:
ssss_MIC
Value: ssss – 4-digit SMS password.
Example: 1111_MIC
Set microphone gain
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK → MICROPHONE GAIN → OK
→ mg → OK
Value: iiii – 4-digit installer code; mg – microphone gain, range – [0... 15].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK → SPEAKER LEVEL → OK
→ sl → OK
Value: iiii – 4-digit installer code; sl – speaker level, range – [0... 85].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Set speaker level
ATTENTION: Phone calls to the preset user phone number in case of alarm are disabled by force when MS mode is enabled
(see 30. MONITORING STATION).
MANUAL ELDES ESIM364 V1.6
EN
101
26.SYSTEM INFORMATION. INFO SMS
The system supports an informational SMS text message identified as the Info SMS, which can be delivered upon request. Once requested,
the system will reply with Info SMS that provides the following:
•
System date & time.
•
System status: partition armed (ON)/disarmed (OFF).
•
GSM signal strength.
•
Mains power supply status.
•
Temperature of the area surrounding primary and secondary temperature sensors (if any).
•
State of zones (OK/alarm).
•
Name and status (ON/OFF) of PGM outputs.
Request for system
information
SMS
Config
Tool
SMS text message content:
ssss_INFO
Value: ssss – 4-digit SMS password.
Example: 1111_INFO
This operation may be carried out from the PC using the ELDES Configuration Tool software.
26.1.Periodic Info SMS
By default, the system sends Info SMS to User 1 phone number periodically once a day at 11:00 (frequency – 1 day; time – 11). The minimum period is every 1 hour (frequency – 0 days; time – 1). Typically, this feature is used to verify the power supply and online status of the
system.
To set a different frequency and time or disable periodic Info SMS, please refer to the following configuration methods.
Set periodic Info SMS
frequency and time
SMS
EKB2
EKB3/
EKB3W
Config
Tool
Disable periodic Info
SMS
SMS
EKB2
102
EN
SMS text message content:
ssss_INFO:fff:it
Value: ssss – 4-digit SMS password; fff – frequency, range – [00... 99] days; it – time, range
– [01... 23].
Example: 1111_INFO:3.15
Menu path:
Frequency: OK → iiii → PRIMARY SETTINGS → OK → INFO SMS SCHEDULER → OK →
FREQUENCY (DAYS) → fff → OK
Time: OK → iiii → PRIMARY SETTINGS → OK → INFO SMS SCHEDULER → OK → TIME → it →
OK
Value: iiii – 4-digit installer code; fff – frequency, range – [00... 125] days; it – time, range –
[01... 23].
Enter parameter 11, time & frequency:
11it fff #
Value: it – time, range – [01... 23]; fff – frequency, range – [00... 125] days.
Example: 110412#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_INFO:00:00
Example: 1111_INFO:00.00
Menu path:
Frequency: OK → iiii → PRIMARY SETTINGS → OK → INFO SMS SCHEDULER → OK →
FREQUENCY (DAYS) → 0 → OK
Time: OK → iiii → PRIMARY SETTINGS → OK → INFO SMS SCHEDULER → OK → TIME → 0 → OK
Value: iiii – 4-digit installer code.
MANUAL ELDES ESIM364 V1.6
EKB3/
EKB3W
Config
Tool
Enter parameter 11, time & frequency:
11 00 00 #
Example: 110000#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: Unlike Info SMS upon request, periodic Info SMS text message does not included zone states, PGM output names and status.
MANUAL ELDES ESIM364 V1.6
EN
103
27.SYSTEM NOTIFICATIONS
By default in case of a certain event, the system attempts to send an SMS text message to the first preset user phone number only. If the
user phone number is unavailable and the system fails to receive the SMS delivery report during 20 seconds, it will attempt to send the SMS
text mes­sage to the next preset user phone number, assigned to the same partition as the previous one. The user phone number may be
unavailable due to the following reasons:
•
mobile phone was switched off.
•
was out of GSM signal coverage.
The system will continue sending the SMS text message to the next preset user phone numbers in the priority order until one is available.
The system sends the SMS text message only once and will not return to the first user phone number if the last one was unavailable.
To change the SMS text message delivery algorithm, user can enable/disable the following parameters for certain events:
•
Send SMS text message to all users simultaneously - This parameter determines whether to ignore the SMS delivery report or
not. Once enabled, the system will attempt to send the SMS text message to every preset user phone number that is enabled to receive
a certain event from the system by SMS text message. In addition, this parameter overrides the SMS delivery report parameter regardless of the SMS delivery report parameter’s status (enabled/disabled).
•
SMS delivery report - This parameter determines whether to request for SMS delivery report or not. Once disabled, the system will
not verify the status of the SMS text message delivery and will attempt to deliver the SMS text message only to the first preset user
phone number regardless if the next preset user phone number (-s) is enabled to receive a certain event by SMS text message or not.
•
Send SMS text message to all users simultaneously - By default, the system sends SMS text message to the first available user
in case of alarm. If the system did not receive the SMS delivery report during 20 seconds, it will attempt to send the SMS text message
to the next preset user phone number. To ignore the SMS delivery report and allow/disallow the system to send the SMS text message
to every preset user phone number, please refer to the following configuration methods.
When using Dual-SIM feature, the Secondary SIM card is involved in the communication process. For more details, please refer to 31. DUAL
SIM MANAGEMENT.
The following table provides the description of system notifications by SMS text message sent to the user phone number.
Seq. No.
1
2
3
4
5
6
Event
System armed
System disarmed
General alarm
Mains power loss/
restore
Battery failed
12
13
14
15
16
Battery dead
or missing
Low battery
Siren fail/restore
Date/time not set
GSM connection failed
GSM/GPRS antenna
fail/restore
Tamper alarm
Keypad failed
Temperature info
System started
Periodical info
17
Wireless signal loss
18
Unable to arm
7
8
9
10
11
104
EN
Description
SMS text message sent to the user regarding armed system.
SMS text message sent to the user about disarmed system.
SMS text message sent to the user in case of system alarm occurrence.
SMS text message sent to the user in case the mains power supply is lost or restored
SMS text message sent to the user in case the backup battery resistance is 2Ω or higher
(battery requires replacement).
SMS text message sent to the user in case the backup battery is not present or the battery voltage
runs below 5V.
SMS text message sent to the user in case the backup battery voltage is 10.5V or lower.
SMS text message sent to the user in case the siren is disconnected/broken or connected/fixed.
SMS text message sent to the user in case system date & time is not set.
SMS text message sent to the user in case the GSM connection is lost.
SMS text message sent to the user in case the GSM/GPRS antenna is disconnected/broken or
connected/broken.
SMS text message sent to the user in case of tamper violation. Indicated as Tamper x.
SMS text message sent to the user in case the keypad is disconnected/broken.
SMS text message sent to the user in case of temperature deviation by the set values.
SMS text message sent to the user on system startup.
Info SMS text message sent to the user periodically by the set values.
SMS text message sent to the user in case the wireless signal is lost. Indicated as No wireless signal
from wless-dev wless-id Tamper x
SMS text message sent to the user in case the system denies arming due to existing violated zone (-s)/tamper (-s).
MANUAL ELDES ESIM364 V1.6
To enable/disable a certain system notification, please refer to the following configuration methods.
Disable system
notification
EKB2
Menu path:
System armed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS ARMED EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK →
SMS REPORT → OK → DISABLE → OK
System disarmed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS DISARMED EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → SMS REPORT → OK → DISABLE → OK
General alarm:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
GENERAL ALARM EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM EV → OK
→ SMS REPORT → OK → DISABLE → OK
Mains power loss/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
MAIN POWER L/R EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R EV → OK
→ SMS REPORT → OK → DISABLE → OK
Battery failed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY FAILED → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
SMS REPORT → OK → DISABLE → OK
Battery dead or missing:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY DEAD/MISS → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ SMS REPORT → OK → DISABLE → OK
Low battery:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY EVENT → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
LOW BATTERY EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY EVENT → OK
→ SMS REPORT → OK → DISABLE → OK
Siren fail/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SIREN FAIL/REST EV → OK → SMS TO ALL → OK → DISABLE → OK
MANUAL ELDES ESIM364 V1.6
EN
105
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ SMS REPORT → OK → DISABLE → OK
Date/time not set:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → DATE/TIME NOT SET → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
DATE/TIME NOT SET → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → DATE/TIME NOT SET → OK
→ SMS REPORT → OK → DISABLE → OK
GSM connection failed:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED →
OK → GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ SMS REPORT → OK → DISABLE → OK
GSM/GPRS antenna fail/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM ANT FAIL/REST → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ SMS REPORT → OK → DISABLE → OK
Tamper alarm:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TAMPER ALARM → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
SMS REPORT → OK → DISABLE → OK
Keypad failed:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → KEYPAD FAILED→ OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
KEYPAD FAILED → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → KEYPAD FAILED → OK →
SMS REPORT → OK → DISABLE → OK
Temperature info:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TEMP INFO EVENT→ OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TEMP INFO EVENT → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TEMP INFO EVENT → OK →
SMS REPORT → OK → DISABLE → OK
System started:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → SYSTEM STARTED EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
SYSTEM STARTED EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → SYSTEM STARTED EV → OK
→ SMS REPORT → OK → DISABLE → OK
Periodical info:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → PERIOD INFO SMS EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
PERIOD INFO SMS EV → OK → SMS TO ALL → OK → DISABLE → OK
106
EN
MANUAL ELDES ESIM364 V1.6
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → PERIOD INFO SMS EV → OK
→ SMS REPORT → OK → DISABLE → OK
Wireless signal loss:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
WLESS SIGN LOSS EV → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ SMS REPORT → OK → DISABLE → OK
Unable to arm:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → FAIL TO ARM SMS → OK →
GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
FAIL TO ARM SMS → OK → SMS TO ALL → OK → DISABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → FAIL TO ARM SMS → OK →
SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
System armed event
User phone number: 25 01 up 0 #
SMS text message to all users simultaneously: 21 01 up 0 #
SMS delivery report: 55 01 up 0 #
System disarmed event
User phone number: 25 02 up 0 #
SMS text message to all users simultaneously: 21 02 up 0 #
SMS delivery report: 55 02 up 0 #
General alarm
User phone number: 25 03 up 0 #
SMS text message to all users simultaneously: 21 03 up 0 #
SMS delivery report: 55 03 up 0 #
Main power loss/restore
User phone number: 25 04 up 0 #
SMS text message to all users simultaneously: 21 04 up 0 #
SMS delivery report: 55 04 up 0 #
Battery failed
User phone number: 25 05 up 0 #
SMS text message to all users simultaneously: 21 05 up 0 #
SMS delivery report: 55 05 up 0 #
Battery dead or missing
User phone number: 25 06 up 0 #
SMS text message to all users simultaneously: 21 06 up 0 #
SMS delivery report: 55 06 up 0 #
Low battery
User phone number: 25 07 up 0 #
SMS text message to all users simultaneously: 21 07 up 0 #
SMS delivery report: 55 07 up 0 #
MANUAL ELDES ESIM364 V1.6
EN
107
Siren fail/restore
User phone number: 25 08 up 0 #
SMS text message to all users simultaneously: 21 08 up 0 #
SMS delivery report: 55 08 up 0 #
Date/time not set
User phone number: 25 10 up 0 #
SMS text message to all users simultaneously: 21 10 up 0 #
SMS delivery report: 55 10 up 0 #
GSM connection failed
User phone number: 25 11 up 0 #
SMS text message to all users simultaneously: 21 11 up 0 #
SMS delivery report: 55 11 up 0 #
GSM/GPRS antenna fail/restore
User phone number: 25 12 up 0 #
SMS text message to all users simultaneously: 21 12 up 0 #
SMS delivery report: 55 12 up 0 #
Tamper alarm
User phone number: 25 13 up 0 #
SMS text message to all users simultaneously: 21 13 up 0 #
SMS delivery report: 55 13 us 0 #
Keypad failed
User phone number: 25 14 up 0 #
SMS text message to all users simultaneously: 21 14 up 0 #
SMS delivery report: 55 14 up 0 #
Temperature info
User phone number: 25 15 up 0 #
SMS text message to all users simultaneously: 21 15 up 0 #
SMS delivery report: 55 15 up 0 #
System started
User phone number: 25 16 up 0 #
SMS text message to all users simultaneously: 21 16 up 0 #
SMS delivery report: 55 16 up 0 #
Periodical info
User phone number: 25 17 up 0 #
SMS text message to all users simultaneously: 21 17 up 0 #
SMS delivery report: 55 17 up 0 #
Wireless signal loss
User phone number: 25 18 up 0 #
SMS text message to all users simultaneously: 21 18 up 0 #
SMS delivery report: 55 18 up 0 #
Unable to arm
User phone number: 25 19 up 0 #
SMS text message to all users simultaneously: 21 19 up 0 #
SMS delivery report: 55 19 up 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2514020#
Config
Tool
108
EN
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Enable system
notification
EKB2
Menu path:
System armed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS ARMED EVENT → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS ARMED EVENT → OK →
SMS REPORT → OK → ENABLE → OK
System disarmed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SYS DISARMED EVENT → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SYS DISARMED EVENT →
OK → SMS REPORT → OK → ENABLE→ OK
General alarm:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
GENERAL ALARM EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → GENERAL ALARM EV → OK
→ SMS REPORT → OK → ENABLE → OK
Mains power loss/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
MAIN POWER L/R EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → MAIN POWER L/R EV → OK
→ SMS REPORT → OK → ENABLE→ OK
Battery failed:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY FAILED → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY FAILED → OK →
SMS REPORT → OK → ENABLE → OK
Battery dead or missing:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
BATTERY DEAD/MISS → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → BATTERY DEAD/MISS → OK
→ SMS REPORT → OK → ENABLE → OK
Low battery:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY EVENT → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
LOW BATTERY EVENT → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → LOW BATTERY EVENT → OK
→ SMS REPORT → OK → ENABLE → OK
Siren fail/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
SIREN FAIL/REST EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → SIREN FAIL/REST EV → OK
→ SMS REPORT → OK → ENABLE → OK
MANUAL ELDES ESIM364 V1.6
EN
109
User phone number: OK → iiii → OK → SMS MESSAGES 1 → OK → DATE/TIME NOT SET → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 1 → OK →
DATE/TIME NOT SET → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 1 → OK → DATE/TIME NOT SET → OK
→ SMS REPORT → OK → ENABLE → OK
GSM connection failed:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED →
OK → GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → SMS TO ALL → OK → DENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ SMS REPORT → OK → ENABLE → OK
GSM/GPRS antenna fail/restore:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
GSM ANT FAIL/REST → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM ANT FAIL/REST → OK
→ SMS REPORT → OK → ENABLE → OK
Tamper alarm:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TAMPER ALARM → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TAMPER ALARM → OK →
SMS REPORT → OK → ENABLE → OK
Keypad failed:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → KEYPAD FAILED→ OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
KEYPAD FAILED → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → KEYPAD FAILED → OK →
SMS REPORT → OK → ENABLE → OK
Temperature info:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → TEMP INFO EVENT→ OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
TEMP INFO EVENT → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → TEMP INFO EVENT → OK →
SMS REPORT → OK → ENABLE → OK
System started:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → SYSTEM STARTED EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
SYSTEM STARTED EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → SYSTEM STARTED EV → OK
→ SMS REPORT → OK → ENABLE → OK
Periodical info:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → PERIOD INFO SMS EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
PERIOD INFO SMS EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → PERIOD INFO SMS EV → OK
→ SMS REPORT → OK → ENABLE → OK
110
EN
MANUAL ELDES ESIM364 V1.6
Wireless signal loss:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
WLESS SIGN LOSS EV → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → WLESS SIGN LOSS EV → OK
→ SMS REPORT → OK → ENABLE → OK
Unable to arm:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → FAIL TO ARM SMS → OK →
GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: OK → iiii → OK → SMS MESSAGES 2 → OK →
FAIL TO ARM SMS → OK → SMS TO ALL → OK → ENABLE → OK
SMS delivery report: OK → iiii → OK → SMS MESSAGES 2 → OK → FAIL TO ARM SMS → OK →
SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Enter parameter 25/21/55, event number, user phone number slot & parameter
status value:
System armed event
User phone number: 25 01 up 1 #
SMS text message to all users simultaneously: 21 01 up 1 #
SMS delivery report: 55 01 up 1 #
System disarmed event
User phone number: 25 02 up 1 #
SMS text message to all users simultaneously: 21 02 up 1 #
SMS delivery report: 55 02 up 1 #
General alarm
User phone number: 25 03 up 1 #
SMS text message to all users simultaneously: 21 03 up 1 #
SMS delivery report: 55 03 up 1 #
Main power loss/restore
User phone number: 25 04 up 1 #
SMS text message to all users simultaneously: 21 04 up 1 #
SMS delivery report: 55 04 up 1 #
Battery failed
User phone number: 25 05 up 1 #
SMS text message to all users simultaneously: 21 05 up 1 #
SMS delivery report: 55 05 up 1 #
Battery dead or missing
User phone number: 25 06 up 1 #
SMS text message to all users simultaneously: 21 06 up 1 #
SMS delivery report: 55 06 up 1 #
Low battery
User phone number: 25 07 up 1 #
SMS text message to all users simultaneously: 21 07 up 1 #
SMS delivery report: 55 07 up 1 #
Siren fail/restore
User phone number: 25 08 up 1 #
SMS text message to all users simultaneously: 21 08 up 1 #
SMS delivery report: 55 08 up 1 #
MANUAL ELDES ESIM364 V1.6
EN
111
Date/time not set
User phone number: 25 10 up 1 #
SMS text message to all users simultaneously: 21 10 up 1 #
SMS delivery report: 55 10 up 1 #
GSM connection failed
User phone number: 25 11 up 1 #
SMS text message to all users simultaneously: 21 11 up 1 #
SMS delivery report: 55 11 up 1 #
GSM/GPRS antenna fail/restore
User phone number: 25 12 up 1 #
SMS text message to all users simultaneously: 21 12 up 1 #
SMS delivery report: 55 12 up 1 #
Tamper alarm
User phone number: 25 13 up 1 #
SMS text message to all users simultaneously: 21 13 up 1 #
SMS delivery report: 55 13 up 1 #
Keypad failed
User phone number: 25 14 up 1 #
SMS text message to all users simultaneously: 21 14 up 1 #
SMS delivery report: 55 14 up 1 #
Temperature info
User phone number: 25 15 up 1 #
SMS text message to all users simultaneously: 21 15 up 1 #
SMS delivery report: 55 15 up 1 #
System started
User phone number: 25 16 up 1 #
SMS text message to all users simultaneously: 21 16 up 1 #
SMS delivery report: 55 16 up 1 #
Periodical info
User phone number: 25 17 up 1 #
SMS text message to all users simultaneously: 21 17 up 1 #
SMS delivery report: 55 17 up 1 #
Wireless signal loss
User phone number: 25 18 up 1 #
SMS text message to all users simultaneously: 21 18 up 1 #
SMS delivery report: 55 18 up 1 #
Unable to arm
User phone number: 25 19 up 1 #
SMS text message to all users simultaneously: 21 19 up 1 #
SMS delivery report: 55 19 up 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 2517041#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
27.1. SMSC (Short Message Service Center) Phone Number
An SMS center (SMSC) is a GSM network element, which routes SMS text messages to the destination user and stores the SMS text message
if the recipient is unavailable. Typically, the phone number of the SMS center is already stored in the SIM card provided by the GSM operator.
If the user fails to receive replies from the system, the SMS center phone number, provided by the GSM operator, must be set manually.
Set SMSC phone
number
SMS
SMS text message content:
ssss_SMS_+ttteeellnnuumm
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits SMSC phone number.
Example: 1111_SMS_+4417031111111
ATTENTION: Before setting the SMSC phone number, please check the credit balance of the system’s SIM card. The system will fail to reply
if the credit balance is insufficient.
112
EN
MANUAL ELDES ESIM364 V1.6
28.EVENT AND ALARM LOG
The event log allows to chronologically register up to 500 timestamped records regarding the following system events:
•
System start.
•
System arming/disarming.
•
Zone violated/restored.
•
Tamper violated/restored.
•
Zone bypassing.
•
Wireless device management.
•
Temperature deviation by MIN and MAX boundaries.
•
System faults.
The event log is of LIFO (last in, first out) type that allows the system to automatically replace the oldest records with the the latest ones.
View event log
EKB2
Menu path:
OK → mmmm → OK → VIEW EVENT LOG → OK
Value: mmmm - 4-digit master code.
To export the event log to .log file or clear it, please refer to the following configuration method.
Export/clear event log
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, event log is enabled. To disable/enable this feature, please refer to the following configuration methods.
Disable event log
EKB2
EKB3/
EKB3W
Enable event log
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → EVENT LOG → OK → DISABLE → OK
Value: iiii - 4-digit installer code.
Enter parameter 36 and parameter status value:
36 0 #
Example: 360#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETTINGS → OK → EVENT LOG → OK → ENABLE → OK
Value: iiii - 4-digit installer code.
EKB3/
Enter parameter 36 and parameter status value:
36 1 #
EKB3W
Config
Tool
Example: 361#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
The alarm log provides a list of last 16 alarm events generated after last arming period. The alarm log can be viewed via EKB2 and includes
only the alarms of the partition that the user/master code is assigned to. Each alarm record includes alarm type, partition number and zone
number. When highlighted, the date and time of the alarm occurrence can be viewed at the bottom of EKB2 screen. In case of alarm,
icon
will appear in home screen view of EKB2. The alarm log auto-clears when the next system arming follows or after viewing it via the keypad.
View alarm log
MANUAL ELDES ESIM364 V1.6
EKB2
Menu path:
OK → uumm → OK → ALARM LOG → OK
Value: uumm - 4-digit user/master code.
EN
113
29.INDICATION OF SYSTEM FAULTS
The system comes equipped with self-diagnostic feature allowing to indicate the presence of any system fault by the keypad as well as by
SMS text message notification to the preset user phone number. By default the indication for all system faults is indicated on the keypad.
To disable/enable the indication of a certain system fault, please refer to the following configuration method.
Disable/enable
individual system fault
indication on keypad
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: After enabling/disabling a certain system fault indication, it is necessary to restart the system locally by powering down and
powering up the system the system or remotely (see 35. REMOTE SYSTEM RESTART).
EN50131-1
GRADE 3
To comply with EN50131-1 Grade 3 standard requirements, the system must be equipped with the following feature:
• System arming is blocked if any system fault exists. The user wil not be able to arm the system until all existing system
faults are solved.
For complete list of EN50131-1 Grade 3 standard requirements and how to enable/disable the associated features, please
refer to 36. EN 50131-1 GRADE 3.
icon displayed in home screen view indicates presence of system faults. In order to view the currently present system faults,
please enter a valid user/master code to access menu section FAULTS. The description on each system fault is provided in the
table below.
EKB2
Menu path:
OK → uumm → OK → FAULTS → OK
Value: uumm – 4-digit user/master code.
Name
MAIN POWER LOSS
LOW BATTERY
BATTERY DEAD/MISS
BATTERY FAILED
SIREN FAILED
VIOLATED TAMPER
DATE/TIME NOT SET
GSM CONNECT FAILED
GSM/GPRS ANTENNA FAILED
WLESS ANTENNA FAIL
KEYPAD LOST
114
EN
Description
Mains power supply is lost
Low backup battery power - backup battery
voltage is 10.5V or lower
Backup battery is not present or the battery
voltage runs below 5V
Backup battery requires replacement - backup
battery resistance is 2Ω or higher
Siren is disconnected/broken
One or more tampers are violated
Date/time not set
GSM connection is lost
GSM/GPRS antenna is disconnected/broken
Wireless antenna is disconnected/broken
Keypad is disconnected/broken
MANUAL ELDES ESIM364 V1.6
EKB3/
EKB3W
Yellow LED SYSTEM indicates system faults. SYSTEM LED indications are mentioned in the table below.
SYSTEM LED
Illuminated continously
Flashing
Description
One or more tampers are violated; other system faults (see below)
One or more high-numbered zones are violated
In order to find out more on the particular system fault, please enter command A provided below. After this procedure the system
will activate red zone LEDs for 15 seconds. The description on each LED indication is mentioned in the table below.
Zone LED
Description
1
Mains power supply is lost
2
Low backup battery power - backup battery voltage is 10.5V or lower
3
Backup battery is not present or the battery voltage runs below 5V
4
Backup battery requires replacement - backup battery resistance is 2Ω or
higher
5
Siren is disconnected/broken
7
One or more tampers are violated
8
Date/time not set
9
One or more high-numbered zones (Z13-Z76) are violated
10
GSM connection is lost
11
GSM/GPRS antenna is disconnected/broken
12
Wireless antenna is disconnected/broken
In order to find out which particular high-numbered zone is violated please , enter command B.
In order to find out which particular tamper is violated please , enter command C.
A. System fault indication - enter command:
[CODE#]
B. Violated high-numbered zone indication – enter command:
[CODE1]
C. Violated tamper indication – enter command:
[CODE2]
The number of violated high-numbered zone or tamper can be calculated using the table below according to the formula: number
from zone LED section B + number from zone LED section A.
Example: LED #3 from section A is flashing and LED #8 from section B is illuminated continuously. According to the table below
LED #8 is equal to number 18, therefore 18 + 3 = 21.
Result: Violated high-numbered zone or tamper number is 21.
Zone LED section - A (flashing)
Zone LED 1 = 1
Zone LED 2 = 2
Zone LED 3 = 3
Zone LED 4 = 4
Zone LED 5 = 5
Zone LED 6 = 6
MANUAL ELDES ESIM364 V1.6
Zone LED section - B (illuminated continously)
Zone LED 7 = 12
Zone LED 8 = 18
Zone LED 9 = 24
Zone LED 10 = 30
Zone LED 11 = 36
Zone LED 12 = 42
EN
115
30.MONITORING STATION
The system can be configured to report events to the monitoring station by transmitting data messages to the monitoring station. The
system connects to the monitoring station when the MS (Monitoring Station) mode is enabled.
Enable MS mode
SMS
SMS text message content:
ssss_SCNSET:ON
Value: ssss – 4-digit SMS password.
Example: 1111_SCNSET:ON
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → MS MODE → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Disable MS mode
Enter parameter 23 & parameter status value:
23 1 #
Example: 231#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_SCNSET:OFF
Value: ssss – 4-digit SMS password.
Example: 1111_SCNSET:OFF
EKB2
Menu path:
OK →iiii → OK → MS SETTINGS → OK → MS MODE → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 23 & parameter status value:
23 0 #
Example: 230#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Account is a 4-digit number (By default – 9999) required to identify the alarm system unit by the monitoring station.
Set account
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → ACCOUNT → OK → cccc → OK
Value: iiii – 4-digit installer code; cccc – 4-digit account number.
EKB3/
Enter parameter 27 & account number:
27 cccc #
EKB3W
Config
Tool
Value: cccc – 4-digit account number.
Example: 278853#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
ATTENTION: The system will NOT send any data to the monitoring station while remote configuration, remote firmware update or remote
listening/2-way voice communication is in progress. However, during the remote configuration session, firmware update process or remote
listening/2-way voice communication process, the data messages will be queued up and transmitted to the monitoring station after the
remote configuration session, firmware update or remote listening/2-way voice communication process is over.
ATTENTION: Phone calls to the preset user phone number via GSM in case of alarm are disabled by force when MS mode is enabled.
116
EN
MANUAL ELDES ESIM364 V1.6
30.1.Data Messages – Events
The configuration of data messages is based on Ademco Contact ID protocol. The data messages can either be transmitted to the monitoring station alone or with duplication by SMS text message to preset user phone number. For more details on system notifications by SMS
text message, please refer to 27. SYSTEM NOTIFICATIONS.
Seq. No.
Contact ID® Code
Event
Description
1
1110
Fire alarm
Transmitted in case a zone of Fire type is violated.
2
3110
Fire restore
Transmitted in case a zone of Fire type is restored.
3
1121
Disarmed by user (Duress
code)
Transmitted in case the system is disarmed by Duress code.
4
1130
Burglary alarm
Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is violated.
5
3130
Burglary restore
Transmitted in case a zone of Delay (if not disarmed before entry delay
countdown is completed), Interior Follower or Instant type is restored.
6
1133
24-Hour zone alarm
Transmitted in case of zone of 24-Hour type is violated.
7
3133
24-Hour zone restore
Transmitted in case of zone of 24-Hour type is restored.
8
1144
Tamper alarm
Transmitted in case the tamper is violated.
9
3144
Tamper restore
Transmitted in case the tamper is restored.
10
1146
Panic/Silent zone alarm
Transmitted in case of zone of Panic/Silent type is violated.
11
3146
Panic/Silent zone restore
Transmitted in case of zone of Panic/Silent type is restored.
12
1158
Temperature risen
Transmitted in case of the temperature has increased above the MAX set
value.
13
1159
Temperature fallen
Transmitted in case of temperature has decreased below the MIN set value.
14
1301
Mains power loss
Transmitted in case the main power supply is lost.
15
3301
Mains power restore
Transmitted in case the main power supply is restored.
16
1302
Low battery
Transmitted in case the backup battery voltage is 10.5V or lower / the
wireless sensor battery level runs below 5%.
17
1308
System shutdown
When the system is running on backup battery power, it transmits the data
message before the backup battery power is fully depleted.
18
1309
Battery failed
Transmitted in case the backup battery resistance is 2Ω or higher.
19
1311
Battery dead or missing
Transmitted in case the backup battery is not present or the battery voltage runs below 5V.
20
3311
Battery connection restore
Transmitted in case the backup battery connecton is fixed.
21
1321
Siren fail
Transmitted in case the siren is disconnected/broken.
22
3321
Siren restore
Transmitted in case the siren is connected/fixed.
23
1330
Keypad fail
Transmitted in case the keypad is disconnected/broken.
24
3330
Keypad restore
Transmitted in case the keypad is connected/fixed
25
1354
GPRS connection loss
Transmitted in case the GPRS connection is lost.
26
1358
GSM connection failed
Transmitted in case the GSM connection is lost.
27
1359
GSM/GPRS antenna fail
Transmitted in case the GSM/GPRS antenna is disconnected/broken
28
3359
GSM/GPRS antenna restore
Transmitted in case the GSM/GPRS antenna is connected/fixed.
29
1381
Wireless signal loss
Transmitted in case the connection with any wireless device is lost.
30
3381
Wireless signal restore
Transmitted in case the connection with any wireless device is restored.
31
1401
Disarmed by user
Transmitted in case the system is disarmed.
32
3401
Armed by user
Transmitted in case the system is armed.
33
1456
Disarmed in Stay mode
Transmitted in case the system is disarmed in Stay mode.
34
3456
Armed in Stay mode
Transmitted in case the system is armed in Stay mode.
35
1463
Disarmed by user (SGS code) Transmitted in case the system is disarmed by SGS code.
36
3463
Armed by user (SGS code)
Transmitted in case the system is armed by SGS code.
37
1570
Zone bypassed
Transmitted in case a violated zone is bypassed.
38
3570
Bypassed zone activated
Transmitted in case a bypassed zone is activated.
39
1602
Test event/Kronos ping
Transmitted for system online status verification purposes.
40
3626
Date/time not set
Transmitted in case system date & time is not set.
41
1900
System started
Transmitted on system startup.
The following table refers to user codes included in arm/disarm data messages.
MANUAL ELDES ESIM364 V1.6
EN
117
Type
User Phone Number 1
User Phone Number 2
User Phone Number 3
User Phone Number 4
User Phone Number 5
User Phone Number 6
User Phone Number 7
User Phone Number 8
User Phone Number 9
User Phone Number 10
iButton 1
iButton 2
iButton 3
iButton 4
iButton 5
Code
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
iButton 6
iButton 7
iButton 8
iButton 9
iButton 10
iButton 11
iButton 12
iButton 13
iButton 14
iButton 15
iButton 16
Master Code
User Code 2
User Code 3
User Code 4
User Code 5
User Code 6
User Code 7
User Code 8
User Code 9
User Code 10
User Code 11
User Code 12
User Code 13
User Code 14
User Code 15
User Code 16
User Code 17
User Code 18
User Code 19
User Code 20
User Code 21
User Code 22
User Code 23
User Code 24
User Code 25
User Code 26
User Code 27
User Code 28
User Code 29
User Code 30
Remote Code (EGR100)
KeyFob 1
KeyFob 2
KeyFob 3
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
133
134
135
118
EN
MANUAL ELDES ESIM364 V1.6
KeyFob 4
KeyFob 5
Arm/Disarm by Zone
Disable data message
MANUAL ELDES ESIM364 V1.6
136
137
213
EKB2
Menu path:
Burglary alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
BURGLR ALM/REST EV → OK → DISABLE → OK
Mains power loss/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK
→ MAIN POWER L/R EV → OK → DISABLE → OK
Armed/disarmed by user: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
ARM/DISARM EVENT → OK → DISABLE → OK
Battery failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → BATTERY
FAILED → OK → DISABLE → OK
Battery dead or missing/battery connection restore: OK → iiii → OK → MS SETTINGS → OK →
DATA MESSAGES 1 → OK → BATTERY DEAD/MISS → OK → DISABLE → OK
Test event: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → TEST EVENT
→ OK → DISABLE → OK
Tamper alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
TAMPER ALM/REST EV → OK → DISABLE → OK
Panic/Silent zone alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1
→ OK → PA/SIL ALM/REST EV → OK → DISABLE → OK
System started: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → SYSTEM
STARTED EV → OK → DISABLE → OK
Fire alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → FIRE
ALM/REST EV → OK → DISABLE → OK
24-Hour zone alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 →
OK → 24H ALM/REST EVENT→ OK → DISABLE → OK
Low battery: OK → iiii → OK → MS SETTINGS → OK →DATA MESSAGES 1 → OK → LOW BATTE
RY EVENT → OK → DISABLE → OK
Temperature risen: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → TEMP
HIGH EVENT → OK → DISABLE → OK
Temperature fallen: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
TEMP LOW EVENT → OK → DISABLE → OK
Wireless signal loss/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 →
OK → WLESS SIGN L/R EV → OK → DISABLE → OK
Disarmed by user (Duress code): OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → DISARM DURESS EV → OK → DISABLE → OK
Armed/disarmed by user (SGS code): OK → iiii → OK → MS SETTINGS → OK → DATA
MESSAGES 2 → OK → ARM/DARM SGS EVENT → OK → DISABLE → OK
Armed/disarmed in Stay mode: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → ARM/DARM STAY EV → OK → DISABLE → OK
Siren fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK → SIREN
FAIL/REST EV → OK → DISABLE → OK
Date/time not set: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK → DATE/
TIME NOT SET → OK → DISABLE → OK
GSM connection failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → DISABLE → OK
GSM/GPRS antenna fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → GSM ANT FAIL/REST → OK → DISABLE → OK
System shutdown: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
SYSTEM SHUTDOWN EV → OK → DISABLE → OK
Keypad fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
KEYPAD FAIL/REST → OK → DISABLE → OK
GPRS connection failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
GPRS CONNECT FAIL → OK → DISABLE → OK
Zone bypassed/activated: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK
→ ZONE BYPASS→ OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EN
119
EKB3/
EKB3W
Config
Tool
120
EN
Enter parameter 24, event number & parameter status value:
24 01 0 # – Burglary alarm/restore
24 02 0 # – Mains power loss/restore
24 03 0 # – Armed/disarmed by user
24 04 0 # – Test event
24 05 0 # – Battery failed
24 06 0 # –Battery dead or missing/battery connection restore
24 07 0 # – Tamper alarm/restore
24 08 0 # – Panic/Silent zone alarm/restore
24 09 0 # – Kronos ping
24 10 0 # – System started
24 13 0 # – 24-Hour zone alarm/restore
24 14 0 # – Fire zone alarm/restore
24 15 0 # – Low battery
24 16 0 # –Temperature risen
24 17 0 # – Temperature fallen
24 18 0 # – Wireless signal loss/restore
24 19 0 # – Disarmed by user (Duress code)
24 20 0 # – Armed/disarmed by user (SGS code)
24 21 0 # – Armed/disarmed in Stay mode
24 22 0 # – Siren fail/restore
24 24 0 # –Date/time not set
24 25 0 # – GSM connection failed
24 26 0 # – GSM/GPRS antenna fail/restore
24 27 0 # – System shutdown
24 28 0 # – Keypad fail/restore
24 29 0 # – GPRS connection failed
24 30 0 # – Zone bypassed/activated
Example: 24080#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
Enable data message
MANUAL ELDES ESIM364 V1.6
EKB2
Menu path:
Burglary alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
BURGLR ALM/REST EV → OK → ENABLE → OK
Mains power loss/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK
→ MAIN POWER L/R EV → OK →ENABLE → OK
Armed/disarmed by user: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
ARM/DISARM EVENT → OK → ENABLE → OK
Battery failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → BATTERY
FAILED → OK → ENABLE → OK
Battery dead or missing/battery connection restore: OK → iiii → OK → MS SETTINGS → OK →
DATA MESSAGES 1 → OK → BATTERY DEAD/MISS → OK → ENABLE → OK
Test event: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → TEST EVENT
→ OK → ENABLE → OK
Tamper alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
TAMPER ALM/REST EV → OK → ENABLE → OK
Panic/Silent zone alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1
→ OK → PA/SIL ALM/REST EV → OK → ENABLE → OK
System started: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → SYSTEM
STARTED EV → OK → ENABLE → OK
Fire alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → FIRE
ALM/REST EV → OK → ENABLE → OK
24-Hour zone alarm/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 →
OK → 24H ALM/REST EVENT→ OK → ENABLE → OK
Low battery: OK → iiii → OK → MS SETTINGS → OK →DATA MESSAGES 1 → OK → LOW BATTE
RY EVENT → OK → ENABLE → OK
Temperature risen: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK → TEMP
HIGH EVENT → OK → ENABLE → OK
Temperature fallen: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 → OK →
TEMP LOW EVENT → OK → ENABLE → OK
Wireless signal loss/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 1 →
OK → WLESS SIGN L/R EV → OK → ENABLE → OK
Disarmed by user (Duress code): OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → DISARM DURESS EV → OK → ENABLE → OK
Armed/disarmed by user (SGS code): OK → iiii → OK → MS SETTINGS → OK → DATA
MESSAGES 2 → OK → ARM/DARM SGS EVENT → OK → ENABLE → OK
Armed/disarmed in Stay mode: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → ARM/DARM STAY EV → OK → ENABLE → OK
Siren fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK → SIREN
FAIL/REST EV → OK → ENABLE → OK
Date/time not set: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK → DATE/
TIME NOT SET → OK → ENABLE → OK
GSM connection failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
GSM CONNECT FAILED → OK → ENABLE → OK
GSM/GPRS antenna fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2
→ OK → GSM ANT FAIL/REST → OK → ENABLE → OK
System shutdown: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
SYSTEM SHUTDOWN EV → OK → ENABLE → OK
Keypad fail/restore: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
KEYPAD FAIL/REST → OK → ENABLE → OK
GPRS connection failed: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK →
GPRS CONNECT FAIL → OK → ENABLE → OK
Zone bypassed/activated: OK → iiii → OK → MS SETTINGS → OK → DATA MESSAGES 2 → OK
→ ZONE BYPASS→ OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EN
121
EKB3/
EKB3W
Config
Tool
122
EN
Enter parameter 24, event number & parameter status value:
24 01 1 # – Burglary alarm/restore
24 02 1 # – Mains power loss/restore
24 03 1 # – Armed/disarmed by user
24 04 1 # – Test event
24 05 1 # – Battery failed
24 06 1 # – Battery dead or missing/battery connection restore
24 07 1 # – Tamper alarm/restore
24 08 1 # – Panic/Silent zone alarm/restore
24 09 1 # – Kronos ping
24 10 1 # – System started
24 13 1 # – 24-Hour zone alarm/restore
24 14 1 # – Fire zone alarm/restore
24 15 1 # – Low battery
24 16 1 # – Temperature risen
24 17 1 # – Temperature fallen
24 18 1 # – Wireless signal loss/restore
24 19 1 # – Disarmed by user (Duress code)
24 20 1 # – Armed/disarmed by user (SGS code)
24 21 1 # – Armed/disarmed in Stay mode
24 22 1 # – Siren fail/restore
24 24 1 # –Date/time not set
24 25 1 # – GSM connection failed
24 26 1 # – GSM/GPRS antenna fail/restore
24 27 1 # – System shutdown
24 28 1 # – Keypad fail/restore
24 29 1 # – GPRS connection failed
24 30 1 # – Zone bypassed/activated
Example: 24031#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
30.2.Communication
The system supports the following communication methods and protocols:
•
GPRS network – EGR100, Kronos, SIA IP protocol.
•
Voice calls (GSM audio channel) – Ademco Contact ID protocol.
•
RS485 data channel.
•
CSD (Cricuit Switched Data).
•
PSTN (landline) – Ademco Contact ID protocol.
•
SMS – Cortex SMS format.
•
ELAN3-ALARM – EGR100, Kronos, SIA IP protocol.
Any communication method can be set as primary or backup connection. The user can set up to 5 backup connections in any sequence order.
Initially, the system communicates via primary connection with the monitoring station. By default, if the initial attempt to transmit data is
unsuccessful, the system will make additional attempts until the data is successfully delivered. If all attempts are unsuccessful, the system
will follow this pattern:
a) The system switches to the backup connection that follows in the sequence (presumably - Backup 1).
b) The system then attempts to transmit data by the backup connection.
c) If the initial attempt is unsuccessful, the system will make additional attempts until the data is successfully delivered.
d) If the system ends up with all unsuccessful attempts, it will switch to the next backup connection in the sequence (presumably - Back­
up 2) and will continue to operate as described in the previous steps. The connection is considered unsuccessful under the following
conditions:
• GPRS network/ELAN3-ALARM – The system has not received the ACK data message from the monitoring station within 40 seconds.
• Voice calls:
• The system has not received the “handshake” signal from the monitoring station within 40 seconds.
• The system has not received the “kissoff” signal from the monitoring station within 5 attempts each lasting 1 second.
• CSD – The system has not received the ACK data message from the monitoring station within 35 seconds.
• PSTN:
• The system has not received the “handshake” signal from the monitoring station within 40 seconds.
• The system has not received the “kissoff” signal from the monitoring station within 5 attempts each lasting 1 second.
• SMS – The system has not received the SMS delivery report from the SMSC (Short Message Service Center) within 45 seconds.
e) If one of the attempts is successful, the system will transmit all queued up data messages by this connection.
f) The system then returns to the primary connection and attempts to transmit the next data messages by primary connection.
g) If the system ends up with all unsuccessful attempts by all connections, it will wait until the Delay after last communication attempt
time (By default – 600 seconds) expires and will return to the primary connection afterwards.
h) If a new data message, except Test Event (ping), is generated during Delay after last communication attempt time, the system will
immediately attempt to transmit it to the monitoring station, regardless of Delay after last communication attempt being in progress.
MANUAL ELDES ESIM364 V1.6
EN
123
PRIMARY
Makes up to 3 or 5 attempts to transmit data
All attempts failed
Switches to BACKUP 1
Makes up to 3 or 5 attempts to transmit data
All attempts failed
One of the attempts is successful
Switches to BACKUP 2
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Switches to BACKUP 3
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Switches to BACKUP 4
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Switches to BACKUP 5
Transmits all queued up data
Makes up to 3 or 5 attempts to transmit data
Returns to PRIMARY
All attempts failed
One of the attempts is successful
Waits for 600 seconds
Transmits all queued up data
Delay after last communication attempt
Returns to PRIMARY
Returns to PRIMARY
NOTE: The number of attempts, indicated in the diagram, are default and depends on the determined communication method.
NOTE: When using Dual-SIM feature, the Secondary SIM card is involved in the communication process. For more details, please refer
to 31. DUAL SIM MANAGEMENT.
124
EN
MANUAL ELDES ESIM364 V1.6
Set primary connection
EKB2
EKB3/
EKB3W
Config
Tool
Set backup connection
1... 5
EKB2
EKB3/
EKB3W
Config
Tool
MANUAL ELDES ESIM364 V1.6
Menu path:
GPRS network: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK →
GPRS → OK
Voice calls: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK → VOICE
CALLS → OK
RS485: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK → RS485 → OK
CSD: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK → CSD → OK
PSTN: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK → PSTN → OK
SMS: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK → SMS → OK
ELAN3-ALARM: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK →
ELAN3-ALARM → OK
connection not in use: OK → iiii → OK → MS SETTINGS → OK → PRIMARY CONNECTION → OK
→ N/A → OK
Value: iiii – 4-digit installer code.
Enter parameter 48 & communication method number:
48 0 # – GPRS network
48 1 # – Voice calls
48 2 # – RS485
48 3 # – CSD
48 4 # – PSTN
48 5 # – SMS
48 6 # – ELAN3-ALARM
48 7 # – connection not in use
Example: 484#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Menu path:
GPRS network: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK →
GPRS → OK
Voice calls: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK →
VOICE CALLS → OK
RS485: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK → RS485 → OK
CSD: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK → CSD → OK
PSTN: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK → PSTN → OK
SMS: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK → SMS → OK
ELAN3-ALARM: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 → OK →
ELAN3-ALARM → OK
connection not in use: OK → iiii → OK → MS SETTINGS → OK → BACKUP CONNECTION1... 5 →
OK → N/A → OK
Value: iiii – 4-digit installer code.
Enter parameter 83, backup connection slot number & communication method
number:
83 bb 0 # – GPRS network
83 bb 1 # – Voice calls
83 bb 2 # – RS485
83 bb 3 # – CSD
83 bb 4 # – PSTN
83 bb 5 # – SMS
83 bb 6 # – ELAN3-ALARM
83 bb 7 # – connection not in use
Value: bb – backup con
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
125
If all attempts by all set connections are unsuccessful, the system will wait until the delay time (By default – 600 seconds) expires and will
attempt to transmit data to the monitoring station again starting with the primary connection.
Set delay after last
communication
attempt
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → DELAY LAST ATTEMPT → OK → aaapp → OK
Value: iiii – 4-digit installer code; aaapp – duration of delay after last attempt, range – [0...
65535] seconds.
EKB3/
Enter parameter 69 & duration of delay after last attempt:
69 aaapp #
EKB3W
Config
Tool
Value: aaapp – duration of delay after last attempt, range – [0... 65535] seconds.
Example: 69200#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: 0 value disables delay after last communication attempt.
NOTE: The system is fully compatible with Kronos NET/Kronos LT monitoring station software for communication via GPRS network. When
using a different monitoring station software, EGR100 middleware is required. EGR100 is freeware and can be downloaded at www.eldes.lt/
en/download
30.2.1.GPRS Network and ELAN3-ALARM
The system supports data transmission to the monitoring station via IP-based networks by GPRS network or Ethernet connection using
ELAN3-ALARM device (see 32.1.4. ELAN3-ALARM - Ethernet Communicator). The supported data formats are the following:
•
EGR100
•
Kronos
•
SIA IP
To set up the system for data transmission via GPRS network or Ethernet using ELAN3-ALARM, please follow the basic configuration steps:
1.
Enable MS Mode parameter (see 30. MONITORING STATION).
2.
Set 4-digit Account number (see 30. MONITORING STATION).
3.
Set server IP address, which is a public IP address of the machine running EGR100, Kronos or SIA IP-based monitoring station software.
4.
Set server port, which is a port of the machine running EGR100, Kronos or SIA IP-based monitoring station software.
5.
Select TCP or UDP protocol. UDP is highly recommended for EGR100 and SIA IP data format.
6.
Select data format: EGR100, Kronos or SIA IP.
7.
In case EGR100 is selected, set 4-digit Unit ID number. Unit ID number can be identical to Account number.
8.
When using GPRS network connection, it is necessary to set up APN, user name and password provided by the GSM operator. Depending on the GSM operator, only APN might be required to set up.
For detailed step-by-step instructions on how to establish the communication between ESIM364 alarm system and EGR100 middleware,
please refer to the middleware’s HELP file.
Set server IP address
SMS
SMS text message content:
ssss_SETGPRS:IP:add.add.add.add
Value: ssss – 4-digit SMS password; add.add.add.add – server IP address.
Example: 1111_SETGPRS:IP:65.82.119.5
EKB2
Menu path:
OK → iiii → OK → GPRS SETTINGS → OK → SERVER IP → OK → add.add. add.add → OK
Value: iiii – 4-digit installer code; add.add.add.add – server IP address.
EKB3/
Enter parameter 40 & server IP address:
40 add add add add #
EKB3W
126
EN
Value: add add add add – server IP address.
Example: 40065082119005#
MANUAL ELDES ESIM364 V1.6
Config
Tool
Set server port
SMS
SMS text message content:
ssss_SETGPRS:PORT:pprrt
Value: ssss – 4-digit SMS password; pprrt – server port number, range – [1... 65535].
Example: 1111_SETGPRS:PORT:5521
EKB2
Menu path:
OK → iiii → OK → GPRS SETTINGS → OK → SERVER PORT → OK → pprrt → OK
Value: iiii – 4-digit installer code; pprrt – server port number, range – [1... 65535].
EKB3/
Enter parameter 44 & server port number:
44 pprrt #
EKB3W
Set DNS1 server IP
address
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → GPRS SETTINGS → OK → DNS1 → OK → add. add.add. add → OK
Value: iiii – 4-digit installer code; add.add.add.add – DNS1 server IP address.
EKB3/
Enter parameter 41 & DNS1 server IP address:
41 add add add add #
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → GPRS SETTINGS → OK → DNS2 → OK → add. add.add. add → OK
Value: iiii – 4-digit installer code; add.add.add.add – DNS2 server IP address.
EKB3/
Enter parameter 42 & DNS2 server IP address:
42 add add add add #
Config
Tool
MANUAL ELDES ESIM364 V1.6
Value: add add add add – DNS1 server IP address.
Example: 41065082119001#
Config
Tool
EKB3W
Set protocol
Value: pprrt – server port number, range – [1... 65535].
Example: 443365#
Config
Tool
EKB3W
Set DNS2 server IP
address
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Value: add add add add – DNS2 server IP address.
Example: 41065082119002#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_SETGPRS:PROTOCOL:ptc
Value: ssss – 4-digit SMS password; ptc – protocol, range – [TCP... UDP].
Example: 1111_SETGPRS:PROTOCOL:UDP
EKB2
Menu path:
OK → iiii → OK → GPRS SETTINGS → OK → PROTOCOL → OK → TCP | UDP → OK
Value: iiii – 4-digit installer code.
EN
127
EKB3W
Enter parameter 43 & protocol number:
43 0 # - TCP
43 1 # - UDP
Example: 431#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Set data format as
Kronos, EGR100 or
SIA IP
Manage SIA IP data
format parameters
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Kronos NET/Kronos LT software communicates via TCP protocol, while EGR100 middle-ware v1.2 and up supports both – TCP and
UDP protocols. However, TCP protocol is NOT recommend to use with EGR100.
ATTENTION: It is necessary to restart the system locally by powering down and powering up the system the system or remotely (see 35.
REMOTE SYSTEM RESTART) after changing the IP address or switching from TCP to UDP.
By default, if the initial attempt to transmit data to the monitoring station via GPRS network or Ethernet method is unsuccessful, the system will make up to 2 additional attempts. If all attempts are unsuccessful, the system will switch to next backup connection that follows in
the sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → IP SETTINGS → OK → IP ATTEMPTS → OK → att → OK
Value: iiii – 4-digit installer code; att – number of attempts, range – [1... 255].
EKB3/
Enter parameter 68 & number of attempts:
68 att #
EKB3W
Config
Tool
Value: att – number of attempts, range – [01... 255].
Example: 6809#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
To report the online status, the system periodically transmits (By default – every 180 seconds) Test Event data message (ping) to the
monitoring station via GPRS network or Ethernet.
Set test period
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → IP SETTINGS → OK → TEST PERIOD → OK →
tteessttpp → OK
Value: iiii – 4-digit installer code; tteessttpp – test period, range – [0... 65535] seconds.
EKB3/
Enter parameter 46 & number of attempts:
46 tteessttpp #
EKB3W
Config
Tool
128
EN
Value: tteessttpp – test period, range – [0... 65535] seconds.
Example: 46120#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
NOTE: 0 value disables test period.
Unit ID is a 4-digit number (By default – 0000) required to identify the alarm system unit by EGR100 middle-ware. It is MANDATORY to
change the default Unit ID before using EGR100.
Set unit ID
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → IP SETTINGS → OK → UNIT ID → OK → unid → OK
Value: iiii – 4-digit installer code; unid – 4-digit unit ID number.
EKB3/
Enter parameter 47 & unit ID number:
47 unid #
EKB3W
Config
Tool
Value: unid – 4-digit unit ID number.
Example: 472245#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For communication via GPRS network, the GPRS parameters provided by the GSM operator are necessary to be set up. To set those parameters, please refer to the following configuration methods.
Set APN
SMS
Config
Tool
Set user name
SMS
Config
Tool
Set password
SMS
Config
Tool
View IP and GPRS
network settings
MANUAL ELDES ESIM364 V1.6
SMS
SMS text message content:
ssss_SETGPRS:APN:acc-point-name
Value: ssss – 4-digit SMS password; acc-point-name – up to 31 character APN (Access Point
Name) provided by the GSM operator.
Example: 1111_SETGPRS:APN:internet
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS:USER:usr-name
Value: ssss – 4-digit SMS password; usr-name – up to 31 character user name provided by
the GSM operator.
Example: 1111_USER:mobileusr
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS:PSW:password
Value: ssss – 4-digit SMS password; password – up to 31 character password provided by
the GSM operator.
Example: 1111_SETGPRS:PSW:mobilepsw
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS text message content:
ssss_SETGPRS?
Example: 1111_SETGPRS?
EN
129
EKB2
Config
Tool
Menu path:
Server IP: OK → iiii → OK → GPRS SETTNGS → OK → IP SETTINGS → OK → SERVER IP
Server port: OK → iiii → OK → GPRS SETTNGS → OK → PORT
DNS1: OK → iiii → OK → GPRS SETTNGS → OK → DNS1
DNS2: OK → iiii → OK → GPRS SETTNGS → OK → DNS2
Protocol: OK → iiii → OK → GPRS SETTNGS → OK → PROTOCOL
DNS1: OK → iiii → OK → GPRS SETTNGS → OK → DNS1
APN: OK → iiii → OK → GPRS SETTINGS → OK → APN
User name: OK → iiii → OK → GPRS SETTINGS → OK → USERS
Password: OK → iiii → OK → GPRS SETTINGS → OK → PASSWORD
Value: iiii – 4-digit installer code.
This operation may be carried out from the PC using the ELDES Configuration Tool software.
30.2.2.Voice Calls and SMS
The system supports up to 3 monitoring station phone numbers for communication with the alarm system by Voice Calls or SMS communication method using Ademco Contact ID or Cortex SMS data format respectively. Tel. Number 1 is mandatory, the other two can be used as
backup phone numbers and are not necessary. The supported phone number formats are the following:
•
International (with plus) – The phone numbers must be entered starting with plus and an international country code in the following format: +[international code][area code][local number], example for UK: +4417091111111. This format can be used when setting
up the phone number by ELDES Configuration Tool software.
•
International (with 00) – The phone numbers must be entered starting with 00 and an international country code in the following
format: 00[international code][area code][local number], example for UK: 004417091111111. This format can be used when setting
up the phone number by EKB2/EKB3/EKB3W keypad.
•
Local – The phone numbers must be entered starting with an area code in the following format: [area code][local number], example
for UK: 017091111111. This format can be used when setting up the phone number by EKB2/EKB3/EKB3W keypad and ELDES Configuration Tool software.
To set up the system for data transmission via Voice Calls or SMS, please follow the basic configuration steps:
1. Enable MS Mode parameter (see 30. MONITORING STATION).
2. Set 4-digit Account number (see 30. MONITORING STATION).
3. Set Tel. Number 1... 3.
Set monitoring station
phone number
EKB2
EKB3/
EKB3W
Delete monitoring
station phone number
Menu path:
OK → iiii → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST → OK → TEL. NUMBER 1... 3 →
OK → ttteeellnnuumm → OK
Value: iiii – 4-digit installer code; ttteeellnnuumm – up to 15 digits monitoring station phone
number.
Enter parameter 26, phone number slot & phone number:
26 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 03]; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Example: 2601004417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST → OK → TEL. NUMBER 1... 3 →
OK → OK
Value: iiii – 4-digit installer code..
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s Tel Number 1 via Voice Calls or SMS method is unsuccessful, the
system will make up to 4 additional attempts. After all unsuccessful attempts, the system will continue to communicate with the monitoring station by switching to the next phone number that follows in the sequence and making up to 4 additional attempts if the initial attempt is unsuccessful. If all attempts to all phone numbers are unsuccessful, the system will switch to next backup connection that follows
in the sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
130
EN
MANUAL ELDES ESIM364 V1.6
Set attempts
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → VOICE CALLS/SMS ST → OK → ATTEMPTS → OK →
at → OK
Value: iiii – 4-digit installer code; at – number of attempts, range – [1... 10].
EKB3W
Enter parameter 37 & number of attempts:
37 at #
Value: at – number of attempts, range – [01... 10].
Example: 3706#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB3/
Due to the individual configuration of each monitoring station, the system may fail to deliver the data message via Voice Calls communication method. In such cases it is recommended to adjust the microphone gain until the optimal value, leading to successful data message
delivery, is discovered.
Set microphone gain
MANUAL ELDES ESIM364 V1.6
EKB2
Menu path:
OK → iiii → OK → PRIMARY SETT INGS → OK → GSM AUDIO → OK → MICROPHONE GAIN → OK
→ mg → OK
Value: iiii – 4-digit installer code; mg – microphone gain, range – [0... 15].
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
131
30.2.3.PSTN
The system supports up to 3 monitoring station phone numbers for communication with the alarm system by PSTN communication meth­od
using Ademco Contact ID data format. Tel. Number 1 is mandatory, the other two can be used as backup phone numbers and are not necessary. The supported phone number formats are the following:
•
International (with 00) – The phone numbers must be entered starting with 00 and an international country code in the following
format: 00[international code][area code][local number], example for UK: 004417091111111. This format can be used when setting
up the phone number by EKB2/EKB3/EKB3W keypad and ELDES Configuration Tool software..
•
Local – The phone numbers must be entered starting with an area code in the following format: [area code][local number], example
for UK: 017091111111. This format can be used when setting up the phone number by EKB2/EKB3/EKB3W keypad and ELDES Configuration Tool software.
To set up the system for data transmission via Voice Calls or SMS, please follow the basic configuration steps:
1. Enable MS Mode parameter (see 30. MONITORING STATION).
2. Set 4-digit Account number (see 30. MONITORING STATION).
3. Set Tel. Number 1... 3.
Set monitoring station
phone number
EKB2
EKB3/
EKB3W
Delete monitoring
station phone number
Menu path:
OK → iiii → OK → MS SETTINGS → OK → PSTN SETTINGS → OK → TEL. NUMBER 1... 3 → OK →
ttteeellnnuumm → OK
Value: iiii – 4-digit installer code; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Enter parameter 58, phone number slot & phone number:
58 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 03]; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Example: 5802004417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → PSTN SETTINGS → OK → TEL. NUMBER 1... 3 → OK → OK
Value: iiii – 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s Tel Number 1 via PSTN method is unsuccessful, the system
will make up to 4 additional attempts. After all unsuccessful attempts, the system will switch to the next phone number that follows
in the sequence and will make up to 4 additional attempts if the initial attempt is unsuccessful. If all attempts to all phone numbers are
unsuccessful, the system will switch to next backup connection that follows in the sequence and will attempt to transmit data until it is
successfully delivered to the monitoring station.
Set attempts
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → PSTN SETTINGS → OK → ATTEMPTS → OK → at → OK
Value: iiii – 4-digit installer code; at – number of attempts, range – [1... 10].
EKB3/
Enter parameter 91 & number of attempts:
91 at #
EKB3W
Config
Tool
Value: at – number of attempts, range – [01... 10].
Example: 9108#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Alternatively, the phone number entries can be treated as phone numbers for receiving calls in case of alarm. For more details on how this
method operates, please refer to 17. ALARM INDICATIONS AND NOTIFICATIONS
132
EN
MANUAL ELDES ESIM364 V1.6
To enable/disable this feature, please refer to the following configuration method.
Enable/disable Treat
PSTN Call as User Call
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
30.2.4.CSD
The system supports up to 5 monitoring station phone numbers for communication with the alarm system by CSD communication method.
Tel. Number 1 is mandatory, the other four can be used as backup phone numbers and are not necessary. The supported phone number
formats are the following:
•
International (with plus) – The phone number must be entered starting with plus and an international country code in the following
format: +[international code][area code][local number], example for UK: +4417091111111. This format can be used when setting up
the phone number by ELDES Configuration Tool software.
•
International (with 00) – The phone number must be entered starting with 00 and an international country code in the following ž
format: 00[international code][area code][local number], example for UK: 004417091111111. This format can be used when setting
up the phone number by EKB2/EKB3/EKB3W keypad.
To set up the system for data transmission via CSD, please follow the basic configuration steps:
1. Enable MS Mode parameter (see 30. MONITORING STATION).
2. Set 4-digit Account number (see 30. MONITORING STATION).
3. Set Tel. Number 1... 5.
Set monitoring station
phone number
EKB2
EKB3/
EKB3W
Delete monitoring
station phone number
Menu path:
OK → iiii → OK → MS SETTINGS → OK → CSD SETTINGS → OK → TEL. NUMBER 1... 5 → OK →
ttteeellnnuumm → OK
Value: iiii – 4-digit installer code; ttteeellnnuumm – up to 15 digits monitoring station phone
number.
Enter parameter 85, number of entry & phone number:
85 ps ttteeellnnuumm #
Value: ps – phone number slot, range – [01... 05]; ttteeellnnuumm – up to 15 digits monitoring station phone number.
Example: 8501004417091111111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EKB2
Menu path:
OK → iiii → OK → MS SETTINGS → OK → CSD SETTINGS → OK → TEL. NUMBER 1... 5 → OK → OK
Value: iiii – 4-digit installer code.
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
By default, if the initial attempt to transmit data to the monitoring station’s phone number via CSD method is unsuccessful, the system will
make up to 4 additional attempts. If all attempts are unsuccessful, the system will switch to next backup connection that follows in the
sequence and will attempt to transmit data until it is successfully delivered to the monitoring station.
Set attempts
EKB2
EKB3/
EKB3W
Config
Tool
MANUAL ELDES ESIM364 V1.6
Menu path:
OK → iiii → OK → MS SETTINGS → OK → CSD SETTINGS → OK → ATTEMPTS → OK → at → OK
Value: iiii – 4-digit installer code; at – number of attempts, range – [1... 10].
Enter parameter 84 & number of attempts:
84 at #
Value: at – number of attempts, range – [01... 10].
Example: 8403#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
EN
133
31.DUAL SIM MANAGEMENT
The Dual-SIM feature allows the system to operate with one of the two inserted SIM cards identified as Primary SIM and Secondary SIM
respectively. The Primary SIM card works as the main default card, while the Secondary SIM card is intended for backup purposes or addition
to the Primary SIM card - SMS text message sending/calling to the preset user phone number and/or communication with the monitoring
station.
The Dual-SIM feature can operate in one of the following modes:
•
Disabled – The Secondary SIM card will not be functional and the system operates with Primary SIM card only (by default – enabled).
•
Automatic – The system switches between the SIM cards in case of a GSM connection or one of the SIM cards failure.
•
Manual – Provides a fully customizable set up of switching between the SIM cards. FOR ADVANCED USERS ONLY!
Manage Dual -SIM
feature
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Regardless of the selected mode, only one of the two SIM cards can operate at the same time.
NOTE: The Dual-SIM feature becomes automatically disabled when the Smart Security feature is in use.
31.1. Disabled Mode
Disabled mode is the default system mode that does not involve the Secondary SIM in the communication process. When this mode is in
use, the system will ignore the Secondary SIM card even if inserted in the SIM card slot.
For more details on how the system communicates with the user and the monitoring station in Disabled mode, please refer to 17. ALARM
INDICATIONS AND NOTIFICATIONS and 30.2. Communication respectively.
31.2. Automatic Mode
Automatic mode involves both SIM cards in the communication process. In this mode there is no Primary or Secondary SIM card hierarchy,
since both cards are equal and the SIM card that is currently in use maintains the GSM connection at all time, unless a failure occurs and the
other card would replace the previous one.
When one of the SIM card fails, the system attempts to re-establish a connection with it by starting an initial reconnection for a set number
of attempts (by default - 3 attempts). If all attempts fail, the system will switch to the other SIM card. If the other SIM card is responsive and
a GSM connection is successfully established, the system will remain operating with that SIM card until it fails. However, if the other SIM
card is unresponsive or it is not present in the SIM card slot, the system will return to the previous SIM card and attempt to establish a GSM
connection with it. If the system fails to carry out this action, after a single attempt it will switch to the other SIM card. This cycle continues
until one of the SIM cards responds and a GSM connection is successfully established. When the SIM card fails, the system will once again
attempt to restore the GSM connection for a set number of attempts (by default – 3 attempts). If all attempts fail, the cycle will continue as
described previously.
In Automatic mode the priority is to transmit data to the monitoring station, but if an event, which requires the system to send an SMS text
message occurs , the system will send the SMS text message via the SIM card that is currently in use. This can only be carried out under
the following conditions:
•
among the attempts to transmit data to the monitoring station (depending on communication method).
•
while switching the monitoring station connections.
•
while switching between the SIM cards.
The following example indicates the situation described above.
134
EN
MANUAL ELDES ESIM364 V1.6
Makes up to 3 or 5 attempt to transmit data via PRIMARY connection on Primary SIM
All attempts failed
One of the attempts successful
Switches to BACKUP1 connection on Primary SIM
Continues transmitting data via PRIMARY connection on Primary SIM card
Makes 1 attempt to transmit data via BACKUP1
connection on Primary SIM, but it is unsuccessful
SMS text message queues up for
sending to user phone number
Attempts to send the text message to user phone number
SMS delivery successful
SMS delivery failed
Continues making the rest of the
attempts (2 or 4) to transmit data via
BACKUP1 connection on Primary SIM
Attempts to send SMS text message
to next available user phone number
All users unavailable
One of the attempts successful
All attempts failed
Transmits all queued up data
Switches to BACKUP2 connection on Primary SIM
Returns to PRIMARY connection on Primary SIM
One of the users available
Sends the SMS text message
Makes up to 3 or 5 attempts
to transmit data via BACKUP2
connection on Primary SIM
Primary SIM card ERROR
Makes up to 3 attempts to
re-establish GSM connection on Primary SIM card
One of the attempts to re-establish GSM connection successful
Makes up to 3 or 5 attempts to transmit data
via BACKUP2 connection on Primary SIM
All attempts failed
One of the attempts successful
Waits for 600 seconds
Transmits all queued up data
Delay after last communication attempt
Returns to PRIMARY connection on Primary SIM
Returns to PRIMARY connection on Primary SIM
Continued in next page
MANUAL ELDES ESIM364 V1.6
EN
135
Continued from previous page
All attempts failed
Makes 1 attempt to switch
to Secondary SIM card
All attempts failed
Attempt successful
Makes up to 3 or 5 attempts to transmit data
via BACKUP2 connection on Secondary SIM
Makes 1 attempt to switch
to Primary SIM card
One of the attempts successful
All attempts failed
Attempt successful
All attempts failed
Transmits all queued up data
Waits for 600 seconds
Continues operating on Primary SIM until the card fails
Makes 1 attempt to switch
to Secondary SIM card
Delay after last communication attempt
Returns to PRIMARY connection on Primary SIM
Continues operating on Secondary SIM until the card fails
Returns to PRIMARY connection on Primary SIM
Continues switching between
the SIM cards until one is available
Continues operating on Secondary SIM until the card fails
NOTE: The number of attempts, indicated in the diagram, are default and depends on the determined communication method
31.3. Manual Mode
Manual mode allows to use both - Primary and Secondary SIM cards and fully customize the algorithm of the communication. The system
can be set up to send SMS text messages/call to the preset user phone number and/or communicate with the monitoring station as follows:
•
Primary SIM – Determines that the SMS text messages/calls/data will be transmitted via the Primary SIM card.
•
Secondary SIM – Determines that the SMS text messages/calls/data will be transmitted via the Secondary SIM card.
•
Currently in use SIM – Determines that the SMS text messages/calls/data will be transmitted via the SIM card that the system is
currently switched to - either Primary or the Secondary SIM card.
•
Return to Primary SIM Enabled – Determines that the Primary SIM card will be the main SIM card of the system. If it is set up to use
the Secondary SIM in the communication process, the system will do so, but after completing the task via the Secondary SIM card, the
system will always return to the Primary SIM card
•
Try to find operator for a maximum of x times – Determines the maximum number of attempts the system should attempt to
re-establish a GSM connection on the current SIM card in case of unsuccessful initial attempt (by default – 3 attempts).
In Manual mode the priority is to transmit data to the monitoring station, but if an event, which requires the system to send an SMS text
message via one of the SIM cards, occurs , the system will switch to the requested SIM card and send the SMS text message. This can only
be carried out under the following conditions:
•
•
•
among the attempts to transmit data to the monitoring station (depending on communication method).
while switching the monitoring station connections.
while switching between the SIM cards.
Example: System settings are the following:
Dual SIM Management:
•
Manual Mode selected
•
Return to Primary SIM – Disabled.
•
Send SMS / Call via – Secondary SIM.
MS Settings – Communication:
•
Primary – Voice Calls via Secondary SIM.
•
Backup1 – CSD via Primary SIM.
•
Backup2 – GPRS Network via Primary SIM.
Let’s say, the system is configured to send an SMS text message to user phone number in case of a Fire Zone Alarm and to transmit data to
136
EN
MANUAL ELDES ESIM364 V1.6
the monitoring station when the system is ARMED. The system is currently switched to the Primary SIM card. The system will follow this
pattern:
a) The user arms the system followed by system switching to the Secondary SIM and attempting to transmit data to the monitoring station via the Primary connection, which is Voice Calls communication method, but fails.
b) The system then switches to the Primary SIM and attempts to transmit data via Backup1 connection, which is CSD communication
method, but fails again.
c) During the event described in step b), a Fire Zone Alarm occurs. The system will switch to the Secondary SIM and attempt to send the
SMS text message to the user regarding this event.
d) The system continues with the data transmission to the monitoring station by switching back to Primary SIM and attempting to transmit data via Backup2 connection, which is GPRS Network communication method, and succeeds.
e) The alarm system switches back to the Primary connection (Voice Calls) and to the Secondary SIM card and waits until the occurrence
of further events.
Attempts to transmit data via PRIMARY connnection (Voice Calls) on Secondary SIM
All attempts failed
Switches to BACKUP1 connection (CSD) on Primary SIM card
Fire Alarm occurs
Stays on Secondary SIM card
Makes up to 5 attempts to transmit data
Attempts to send SMS text message to user phone number
One of the attempts successful
Transmits all queued up data
All attempts failed
SMS delivery successful
Returns to Primary connnection
(Voice Calls) on Secondary SIM
SMS delivery failed
Attempts to send SMS text
message to next available
user phone number
One of the users available
Sends the SMS text message
All users unavailable
Switches to Backup2
(GPRS Network) connection on Primary SIM card
Makes up to 3 attempts
to transmit data
All attempts failed
One of the attempts successful
Waits for 600 seconds
Transmits all queued up data
Delay after last communication attempt
Returns to Primary connnection
(Voice Calls) on Secondary SIM
Returns to PRIMARY connnection
(Voice Calls) on Secondary SIM
NOTE: The number of attempts, indicated in the diagram, are default and depends on the determined communication method
NOTE: If the Return to Primary SIM parameter is enabled, the system would return to the Primary SIM after each data transmission.
MANUAL ELDES ESIM364 V1.6
EN
137
32.ELDES WIRED DEVICES
32.1. RS485 Interface
RS485 interface is used for the system to communicate with the following devices:
•
EKB2 keypads (up to 4 units).
•
EKB3 keypads (up to 4 units).
•
EPGM1 modules (up to 2 units).
•
ELAN3-ALARM (1 unit)
The terminals of RS485 interface are Y (yellow wire) and G (green wire), which are clock and data respectively. The devices, connected to
RS485 interface, must be powered from the AUX+ and AUX- terminals.
For more details on RS485 device wiring, please refer to 3.2.7. RS485.
32.1.1. EKB2 - LCD Keypad
EKB2 is an LCD keypad intended for using with ESIM364 alarm system.
Main EKB2 features:
•
Alarm system arming and disarming (see 12.3. EKB2 Keypad and User Password).
•
Arming and disarming in Stay mode (see 15. STAY MODE).
•
System parameter configuration (see 5. CONFIGURATION METHODS).
•
PGM output control (see 18.4. Turning PGM Outputs ON and OFF).
•
System information display (see 32.1.1.4. Visual and Audio Indications).
•
Audio indication by built-in buzzer (see 32.1.1.4. Visual and Audio Indications ).
•
Wireless device information display (see 19.2. Wireless Device Information and Signal Status Monitoring).
•
Temperature display (see 32.1.1.1.2 Keys Functionality).
•
Time display (see 32.1.1.1.2 Keys Functionality).
The system configuration is performed by accessing EKB2 menu and entering the required values. ESIM364 system allows to connect up
to 4 EKB2 keypads.
32.1.1.1. Technical Specifications
32.1.1.1.1 Electrical & Mechanical Characteristics
Power supply
12-14V
Maximum keypad connection cable length
100 m.
Dimensions
133 x 89 x 19 mm
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Range of operating temperatures
0...+55ºC
138
EN
150mA max.
MANUAL ELDES ESIM364 V1.6
32.1.1.1.2 Keys Functionality
One menu level back / cancel
41
Menu navigation – up
Temperature
Custom keypad
partition title
Digital clock
Menu navigation – down
20,20C
GSM signal
strength
Confirm (enter) value
...
00:45
GARAGE
KITCHEN
BEDROOM
CORRIDOR
System status and alarm
indication
Value typing
Minus character to enter negative
temp. value
Bypassed
violated zone
(-s)
System
fault (-s) is
present
System
STAY-armed
Additional menu / minus character to enter negative temp. value
Home screen
view
Fire-type
zone violated
32.1.1.1.3 Connector and Main Unit Functionality
Vin
Positive power supply terminal
COM
Negative power supply terminal
G
RS485 interface for communication (green wire)
Y
RS485 interface for communication (yellow wire)
COM
Common terminal for Z1
Z1
Security zone terminal
A0
Keypad address pin
A1
Keypad address pin
Buzzer
Buzzer for audio indications
Tamper
Tamper-button for EKB2 enclosure status monitoring
MANUAL ELDES ESIM364 V1.6
42
VIN
COM
Z1
G
Y
COM
A0A1
Buzzer
Tamper
EN
139
32.1.1.1.4 Keypad Address
A0 and A1 pins located on the back side of the keypad are intended to set keypad address. The keypad address is set by putting the jumper
(-s) on the pins. ESIM364 system allows to connect up to 4 EKB2 keypads - each set under different address. Jumper combinations for different keypad address configuration are indicated in the table below.
Address
A0
A1
Jumper position
A0
A1
Keypad 1
A0
A1
Keypad 2
A0
A1
Keypad 3
Keypad 4
The address of each connected keypad is also indicated in ELDES Configuration Tool software.
32.1.1.2. Installation
45
46
ESIM364
Y G
VIN
COM
Z1
AUX- AUX+
EKB2
G
Y
COM
5,6kΩ
32.1.1.3. Visual and Audio Indications
EKB2 can be used even in dark premises as the LCD screen and keys are illuminated continuously. The illumination level lowers down if 3 minutes after the last key-touch expires while the system is disarmed. In case of alarm, the keypad illumination level is boosted and stays in this
state until the system is disarmed.
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried
out configuration, one long beep – for invalid configuration. In addition, the buzzer emits short beeps in case of alarm and exit/entry delay
countdown.
32.1.1.4.
EKB2 Zone and Tamper
Keypad EKB2 has one wired zone Z1 and one tamper button. By default, the keypad zone Z1 is disabled. The keypad zone can be enabled by
SMS, EKB2 keypad, EKB3 keypad, EKB3W keypad and ELDES Configuration Tool software (see 14.9. Disabling and Enabling Zones). When
Z1 is enabled, it operates like any other system zone, therefore a sensor can be connected to it. In addition, Z1 and COM terminals must be
connected with resistor of 5,6kΩ nominal.
The tamper button is intended for monitoring the enclosure status of EKB2, therefore the system causes alarm if the enclosure is illegally
opened. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is required.
140
EN
MANUAL ELDES ESIM364 V1.6
32.1.1.5. Icons and Messages
Icon / Message
(by default - disabled)
(by default - disabled)
Description
Partition is armed and menu is locked
Partition is disarmed and menu is unlocked
Configuration mode activated
Zone or tamper alarm in partition
Partition is ready to be armed.
Partition is not ready to be armed – one or
more zones / tampers violated.
One or more system faults present
One or more violated zones bypassed
One or more partitions STAY-armed
One or more Fire-type zones violated
Alarms in alarm log present
SERVICE MODE
Service mode activated
MANUAL ELDES ESIM364 V1.6
EN
141
32.1.1.6. Menu Tree
HOME SCREEN VIEW
P2
user or master code
OK
uumm
mmmm
part-name... part-name
master code
ARM/DIS PARTITION
part-name... part-name
ARM ALL
ARM ALL
DISARM ALL
DISARM ALL
user code
uuuu
BYPASS
ARM/DIS PARTITION
BYP VIOLATED ZONES
part-name... part-name
Z1-zone-name...
Z17-zone-name
BYPASS LIST 1
ARM ALL
UNBYPASS | BYPASS
DISARM ALL
Z18-zone-name...
Z34-zone-name
BYPASS LIST 2
BYPASS
UNBYPASS | BYPASS
BYP VIOLATED ZONES
Z1-zone-name...
Z17-zone-name
Z35-zone-name...
Z51-zone-name
BYPASS LIST 3
BYPASS LIST 1
UNBYPASS | BYPASS
UNBYPASS | BYPASS
Z18-zone-name...
Z34-zone-name
Z52-zone-name...
Z68-zone-name
BYPASS LIST 4
BYPASS LIST 2
UNBYPASS | BYPASS
UNBYPASS | BYPASS
Z35-zone-name...
Z51-zone-name
Z69-zone-name...
Z76-zone-name
BYPASS LIST 5
BYPASS LIST 3
UNBYPASS | BYPASS
UNBYPASS | BYPASS
Z52-zone-name...
Z68-zone-name
VIOLATED ZONES
BYPASS LIST 4
VIOLATED TAMPERS
UNBYPASS | BYPASS
Z69-zone-name...
Z76-zone-name
FAULTS
BYPASS LIST 5
UNBYPASS | BYPASS
Z1-zone-name... Z76-zone-name
tamp-name... tamp-name
VIOLATED ZONES
VIOLATED TAMPERS
BATTERY DEAD/MISS | BATTERY FAILED | SIREN FAILED
| GSM CONNECT FAILED | GSM/
GPRS ANTENNA FAILED |
VIOLATED TAMPER | MAIN
POWER LOSS | DATE/TIME NOT
SET | LOW BATTERY | WLESS
SIGNAL LOST | KEYPAD LOST
Z1-zone-name... Z76-zone-name
FAULTS
tamp-name... tamp-name
BATTERY DEAD/MISS | BATTERY FAILED | SIREN FAILED
| GSM CONNECT FAILED | GSM/
GPRS ANTENNA FAILED |
VIOLATED TAMPER | MAIN
POWER LOSS | DATE/TIME NOT
SET | LOW BATTERY | WLESS
SIGNAL LOST | KEYPAD LOST
DATE/TIME SETTINGS
yyyy-mt-dd hh-mn
TEMP SENSORS INFO
1. tm.p C (PRIM) | (SEC)... 8. tm.p C
VIEW EVENT LOG
CODES
BYP VIOLATED ZONES
Continued in next page
142
EN
MANUAL ELDES ESIM364 V1.6
1. tm.p C (PRIM) | (SEC)... 8. tm.p C
TEMP SENSORS INFO
codes
Continued from
previous page
mmmm
DATE/TIME SETTINGS
uuuu
yyyy-mt-dd hh-mn
MASTER CODE
ALARM LOG
installer code
USER CODE (2-17)
PARTITION
CALL/SMS SETTINGS
[0000... 9999]
USER CODE (18-30)
USER CODE 18... 30
15 digits
ttteeellnnuumm
CODE
PARTITION
[0000... 9999]
PARTITION
partition value
DURESS CODE
CALL IN CASE ALARM
DISABLE | ENABLE
[0000... 9999]
CODE
PHONE NUMBER
pv
partition value
USER CODE 2... 17
iiii
PRIMARY SETTINGS
USERS
pv
PARTITION
CONFIGURATION
GSM USER 1... 10
[0000... 9999]
CODE
SGS CODE
GSM USER 1... 10
[0000... 9999]
N/A | MASTER CODE
| USER CODE 2... 10
N/A | MASTER CODE | USER CODE 2... 10
REMOVE CODE
[0000... 9999]
CTRL FROM ANY NUM
ALARM LOG
[0000... 9999]
INSTALLER CODE
[0000... 9999]
[0001... 9999]
yyyy-mt-dd hh-mn
days
[0... 99]
ZONES
MASTER CODE
ONBOARD ZONES
SMS PASSWORD
ZONE 1... 12
DATE/TIME SETTINGS
NAME
INFO SMS SCHEDULER
STATUS
FREQUENCY (DAYS)
hour
[0... 23]
TYPE
TIME
DISABLE / ENABLE
STAY
TEMP. MIN
FORCE
[-55... 125]
TEMP. MAX
WIRELESS ZONES 1... 4
NAME
NAME
SECOND. TEMP SENS
STATUS
TYPE
EXIT DELAY
PARTITION 1... 4
[1... 10]
ALARM DURATION
MANUAL ELDES ESIM364 V1.6
partition value
DISABLE | ENABLE
DISABLE | ENABLE
INTERRIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/SILENT
ENTRY DELAY
SIREN SETTINGS
minutes
pv
WIRELESS ZONE 13... 76
PRIMARY TEMP SENS
[0... 600]
seconds
DISABLE | ENABLE
PARTITION
[-55... 125]
seconds
[1... 65535]
TAMPER NAME
TEMPERATURE SENS 1... 8
°C
INTERRIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/SILENT
ENTRY DELAY
EVENT LOG
TEMP SENSORS
°C
DISABLE | ENABLE
Continued in next page
STAY
[1... 65535]
seconds
DISABLE | ENABLE
EN
143
SRN IF WLESS LOSS
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
WIRELESS
ZONE 13... 76
DISABLE | ENABLE
ZONES
BELL SQUAWK STAY
Continued from
previous page
iiii
DISABLE | ENABLE
PRIMARY SETTINGS
BELL SQUAWK
SIREN SETTINGS
DISABLE | ENABLE
EWS2 LED
seconds
[0... 65535]
STATUS
TYPE
STAY
RESTORE DELAY
PARTITION SWITCH
FORCE
DISABLE | ENABLE
NAME
STATUS
[1] EKB2 | NOT USED...
[4] EKB2 | NOT USED
TYPE
DISABLE | ENABLE
INTERRIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/SILENT
ENTRY DELAY
EKB3W PARTITION
STAY
EKB3W wless-id | NOT USED
[1... 65535]
seconds
DISABLE | ENABLE
TAMPER NAME
GSM AUDIO
PARTITION
MICROPHONE GAIN
[0... 100]
partition value
pv
1... 16. EPGM1 ZONE 13... 28
PARTITION SWITCH
[0... 15]
seconds
EPGM1 ZONES 1-16
[1] EKB2 | NOT USED...
[4] EKB2 | NOT USED
PARTITION 1... 2
[1... 65535]
DISABLE | ENABLE
PARTITION
PARTITION SWITCH
PARTITION 1... 4
INTERRIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/SILENT
TAMPER NAME
KEYPAD PARTITION
PARTITION 1... 4
DISABLE | ENABLE
ENTRY DELAY
LOSS DELAY
KEYPAD PARTITION
DISABLE | ENABLE
DISABLE | ENABLE
NAME
EWF1 SIREN INTERC.
[0... 65535]
FORCE
partition value
pv
1ST... 4TH KEYPAD ZONE
EWS3 FIRE LED
MAIN POWER STATUS
seconds
PARTITION
KEYPAD ZONES
EWS3 ALARM LED
DISABLE | ENABLE
TAMPER NAME
FORCE
SPEAKER LEVEL
partition value
pv
DISABLE | ENABLE
EPGM1 ZONES 17-32
PGM OUTPUTS
DISABLE | ENABLE
OUTPUT 1... 12
USING EPGM8
NAME
ONBOARD OUTPUTS
STATUS
NAME
STATUS
TYPE
DISABLE | ENABLE
STAY
NAME
STATUS
[1... 65535]
seconds
DISABLE | ENABLE
PARTITION
Continued in next page
EN
INTERRIOR FOLLOWER | INSTANT | 24-HOUR |
DELAY | FIRE | PANIC/SILENT
TAMPER NAME
WIRELESS OUTPUT 13... 76
144
DISABLE | ENABLE
ENTRY DELAY
WIRELESS OUTPUTS 1... 4
DISABLE | ENABLE
17... 32. EPGM1 ZONE 29... 44
pv
partition value
FORCE
MANUAL ELDES ESIM364 V1.6
FW RELEASE
ERROR RATE
SIGNAL
BATTERY
IBUTTON KEYS
DISABLE | ENABLE
NEW IBUTTON
iiii
ZONES
WIRELESS DEVICES 1... 2
wless-dev wless-id
ATZ MODE
DISABLE | ENABLE
ZONE TYPE:6-ZONE M
TYPE 1... 3
ZONE TYPE:ATZ MODE
TYPE 4... 5
ZONE 1... 4
ARM/DISARM BY ZONE
CHIME
0 | [1... 12]
0:OFF or 1-12
DISABLE | ENABLE
IBUTTON 1... 16
MS SETTINGS
REMOVE
PARTITION
partition value
ID
ACCOUNT
[0000... 9999]
pv
GPRS SETTINGS
DELAY LAST ATTEMPT
MS MODE
APN
[0... 65535]
DISABLE | ENABLE
DATA MESSAGES 1
USER
DISABLE | ENABLE
BURGLR ALM/REST EV
PASSWORD
DISABLE | ENABLE
MAIN POWER L/R EV
PROFILE
BATTERY FAILED
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
BATTERY DEAD/MISS
SYS ARMED EVENT
DISABLE | ENABLE
DISABLE | ENABLE
ARM/DISARM EVENT
SMS MESSAGES 1
SMS TO ALL
PA/SIL ALM/REST EV
DISABLE | ENABLE
SYSTEM STARTED EV
DISABLE | ENABLE
DISABLE | ENABLE
24H ALM/REST EVENT
DISABLE | ENABLE
SMS REPORT
SYS DISARMED EVENT
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
TEMP LOW EVENT
SMS TO ALL
ARM/DARM DURESS EV
DISABLE | ENABLE
ARM/DARM SGS EVENT
DISABLE | ENABLE
SMS REPORT
SMS TO ALL
MANUAL ELDES ESIM364 V1.6
DISABLE | ENABLE
SYSTEM SHUTDOWN EV
SMS REPORT
GSM USER 1... 10
DISABLE | ENABLE
GSM CONNECT FAILED
KEYPAD FAIL/REST
GPRS CONNECT FAIL
BATTERY FAILED
DISABLE | ENABLE
DISABLE | ENABLE
DATE/TIME NOT SET
GSM ANT FAIL/REST
DISABLE | ENABLE
DISABLE | ENABLE
SIREN FAIL/REST EV
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
ARM/DARM STAY EV
MAIN POWER L/R EV
DISABLE | ENABLE
DISABLE | ENABLE
DATA MESSAGES 1
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
WLESS SIGN L/R EV
SMS REPORT
DISABLE | ENABLE
DISABLE | ENABLE
TEMP HIGH EVENTMISS
SMS TO ALL
GENERAL ALARM EV
DISABLE | ENABLE
LOW BATTERY EVENT
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
FIRE ALM/REST EV
ZONE BYPASS EV
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
Continued in next page
EN
145
SMS REPORT
BATTERY DEAD/MISS
DISABLE | ENABLE
iiii
MS SETTINGS
DISABLE | ENABLE
SMS TO ALL
SMS MESSAGES 1
DISABLE | ENABLE
VOICE CALLS/SMS ST
TEL. NUMBER 1... 3
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
SMS TO ALL
IP SETTINGS
SERVER IP
IP address
GSM USER 1... 10
DNS1
[0.0.0.0]
IP address
DNS2
[0.0.0.0]
IP address
SMS TO ALL
SMS REPORT
PROTOCOL
UNIT ID
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
SMS TO ALL
DISABLE | ENABLE
SERVICE MODE
SMS REPORT
CLEAR TAMPER FAULT
RESET TO DEFAULT
uumm
SMS TO ALL
user or master code
SMS REPORT
GSM USER 1... 10
DISABLE | ENABLE
seconds
GPRS | VOICE CALLS | RS485 | CSD
| PSTN | SMS | ELAN3-ALARM | N/A
SMS TO ALL
TAMPER ALARM
DISABLE | ENABLE
[0... 65535]
BACKUP CONNECTION 1... 5
GSM USER 1... 10
DISABLE | ENABLE
[0000... 9999]
GPRS | VOICE CALLS | RS485 | CSD
| PSTN | SMS | ELAN3-ALARM | N/A
SMS REPORT
GSM ANT FAIL/REST
DISABLE | ENABLE
[0... 255]
PRIMARY CONNECTION
GSM USER 1... 10
DISABLE | ENABLE
TCP | UDP
TEST PERIOD
GSM CONNECT FAILED
DISABLE | ENABLE
[1... 65535]
IP ATTEMPTS
DATE/TIME NOT SET
DISABLE | ENABLE
[0.0.0.0]
SERVER PORT
SMS MESSAGES 2
DISABLE | ENABLE
15 digits
SIREN FAIL/REST EV
DISABLE | ENABLE
DISABLE | ENABLE
ttteeellnnuumm
[1... 10]
TEL NUMBER 1... 5
SMS REPORT
DISABLE | ENABLE
DISABLE | ENABLE
15 digits
CSD SETTINGS
ATTEMPTS
DISABLE | ENABLE
ttteeellnnuumm
SMS REPORT
LOW BATTERY EVENT
DISABLE | ENABLE
15 digits
[1... 10]
ATTEMPTS
SMS TO ALL
TEL. NUMBER 1... 3
DISABLE | ENABLE
ttteeellnnuumm
PSTN SETTINGS
GSM USER 1... 10
DISABLE | ENABLE
[1... 10]
ATTEMPTS
PERIOD INFO SMS EV
GSM USER 1... 10
SMS TO ALL
SMS TO ALL
SMS REPORT
SMS REPORT
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
Continued in next page
146
EN
MANUAL ELDES ESIM364 V1.6
WLESS SIGN LOSS EV
DISABLE | ENABLE
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
SMS TO ALL
SMS REPORT
TEMP INFO EVENT
DISABLE | ENABLE
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
SMS MESSAGES 2
KEYPAD FAIL/REST
GSM USER 1... 10
SMS TO ALL
SMS REPORT
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
FAIL TO ARM SMS
GSM USER 1... 10
SMS TO ALL
SMS TO ALL
SMS REPORT
SMS REPORT
DISABLE | ENABLE
DISABLE | ENABLE
DISABLE | ENABLE
SYSTEM STARTED EV
DISABLE | ENABLE
GSM USER 1... 10
DISABLE | ENABLE
DISABLE | ENABLE
MANUAL ELDES ESIM364 V1.6
SMS TO ALL
SMS REPORT
EN
147
32.1.2. EKB3 - LED Keypad
EKB3 is a LED keypad intended for using with ESIM364 alarm system.
Main EKB3 features:
•
Alarm system arming and disarming (see 12.4. EKB3 Keypad and User Password).
•
•
•
•
•
•
Arming and disarming in Stay mode (see 15. STAY MODE).
System parameter configuration (see 5. CONFIGURATION METHODS).
PGM output control (see 18.4. Turning PGM Outputs ON and OFF).
Visual indication by LED indicators (see 32.1.2.3. Visual and Audio Indications).
Audio indication by built-in buzzer (see 32.1.2.3. Visual and Audio Indications).
Keypad partition switch (see 23.3. Keypad Partition and Keypad Partition Switch).
The system configuration by EKB3 keypad is performed by activating the Configuration mode (see 5. CONFIGURATION METHODS) and entering the required parameters & values. ESIM364 system allows to connect up to 4 EKB3 keypads.
32.1.2.1. Technical Specifications
32.1.2.1.1 Electrical & Mechanical Characteristics
Power supply
12-14V
150mA max
Maximum keypad connection cable length
100 m.
Dimensions
140x100x18mm
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Range of operating temperatures
-30...+55ºC
32.1.2.1.2 LED Functionality
ARMED
Steady ON - alarm system is armed / exit delay in progress; flashing - Configuration mode activated
READY
Steady ON - system is ready – no violated zones and tampers
SYSTEM
Steady ON - system faults; flashing - violated high-numbered zone (-s)
BYPS
Steady ON - zone bypass mode
1-12
Steady ON - violated zone Z1-Z12
32.1.2.1.3 Keys Functionality
[BYPS]
Bypass violated zone
[CODE]
System fault list / violated high-numbered zone indication / violated tamper indication
[*]
Clear typed in characters
[#]
Confirm (enter) command
[0] ... [9]
Command typing
[1] ... [4]
Keypad partition switch / steady ON - armed partition indication / flashing - violated partition indication
[0]
Simultaneous 4-partition arming
[STAY]
Manual system arming in Stay mode
[INST]
1st character for Configuration mode activation/deactivation command
32.1.2.1.4 Connector Functionality
AUX+
Positive power supply terminal
AUX-
Negative power supply terminal
G
RS485 interface for communication (green wire)
Y
RS485 interface for communication (yellow wire)
COM
Common terminal for Z1
Z1
Security zone terminal
Z2
N/A
3, 2
Keypad address pins
1
N/A
148
EN
MANUAL ELDES ESIM364 V1.6
BACK SIDE
FRONT SIDE
47
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
10
11
5
12
6
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
3 2 1
TAMPER
COM Y AUXZ2 Z1
G AUX+
32.1.2.1.5 Keypad Address
Pins 3 and 2 located on the back side of the keypad are intended to set keypad address. The keypad address is set by putting the jumper (-s)
on the pins. ESIM364 system allows to connect up to 4 EKB3 keypads - each set under different address. Jumper combinations for different
keypad address configuration are indicated in the table below.
Address Configuration
Jumper position
3 2
Address
1
Keypad 1
3 2
1
Keypad 2
3 2
1
Keypad 3
3 2
1
Keypad 4
NOTE: Pins 1 are inactive.
The address of each connected keypad is also indicated in ELDES Configuration Tool software.
32.1.2.2. Installation
1. Detach keypad holder from EKB3 keypad . Keypad holder detach points are marked with arrows.
48
DOWN SIDE
BACK SIDE
MANUAL ELDES ESIM364 V1.6
EN
149
2. Disconnect alarm system ESIM364 power supply and backup battery before connecting the wires.
49
ESIM364
Y G
AUX- AUX+
EKB3
COM Y AUXZ2 Z1
G AUX+
5,6kΩ
3. Wire up keypad terminals to ESIM364 alarm system respectively – AUX+ to AUX+, AUX- to AUX-, Y to Y, G to G. (see Fig. No. 49).
4. Connect a sensor and the resistor across Z1 and COM terminalss in accordance with zone connection Type 1 or Type 2 (see 2.3.2. Zone
Connection Types). As keypad zone Z1 is disabled by default, it can be enabled by SMS, ELDES Configuration Tool, EKB2, EKB3 and EKB3W keypad. Z2 terminal is permanently inactive. Keypad zone Z1 must be enabled and resistor connected even if the tamper button
alone is required (see Fig. No. 47).
NOTE: Keypad zone connection type can differ from selected on-board zone connection type.
NOTE: ATZ mode is NOT supported by keypad zones. ATZ mode is ineffective for keypad zones when enabled.
5. Set the keypad address by combining DIP switch positions (see 32.1.2.1.5 Keypad Address).
6. Infix the keypad into the holder (see Fig. No. 48).
ATTENTION: Before fixing the keypad into the holder please , make sure that the tamper is properly pressed (see Fig. No. 47).
7. Power up ESIM364 alarm system.
8. EKB3 keypad is ready.
For more details on multiple keypad wiring, please refer to 3.2.7. RS485.
32.1.2.3. Visual and Audio Indications
EKB3 keys have a LED back-light, therefore it is possible to use this keypad even in dark premises. The back-light lasts for 3 minutes after the
last key-stroke while the system is disarmed. In case of alarm, the keypad back-light turns ON and lasts until the system is disarmed.
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried
out configuration command, one long beep – for invalid configuration command. In addition, the buzzer emits short beeps in case of alarm and
exit/entry delay countdown.
32.1.2.4. EKB3 Zone & Tamper
Keypad EKB3 has one wired zone Z1 and one tamper button. By default, the keypad zone Z1 is disabled. The keypad zone can be enabled by
SMS, EKB2 keypad, EKB3 keypad, EKB3W keypad and ELDES Configuration Tool software (see 14.9. Disabling and Enabling Zones). Zone
Z1 is enabled, it operates like any other system zone, therefore a sensor can be connected to it. In addition, Z1 and COM terminals must be
connected with resistor of 5,6kΩ nominal.
The tamper button is intended for monitoring the enclosure status of EKB3, therefore the system causes alarm if the enclosure is illegally
opened. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is required.
150
EN
MANUAL ELDES ESIM364 V1.6
32.1.3. EPGM1 - Hardwired Zone & PGM Output Expansion Module
EPGM1 is a hardwired zone & PGM output expansion module intended for using with ELDES alarm systems.
Main EPGM1 features:
• Hardwired zone expansion. Each module adds 16 additional zones;
• Hardwired PGM output expansion. Each module adds 2 additional PGM outputs for electrical appliance connection;
• Up to 32 hardwired zone and up to 4 hardwired PGM output expansion.
32.1.3.1. Technical Specifications
32.1.3.1.1 Electrical & Mechanical Characteristics
Power supply
Number of digital inputs
Nominal resistance
Number of PGM outputs
Maximum PGM output current
EPGM1 PGM output circuit
10-24V
16
5,6kΩ
2
250 mA
100mA max without auxiliary equipment.
Maximum commuting PGM output values
AUX: auxiliary equipment power supply
Dimensions
Humidity
Voltage – 30V; current 250mA
13,8V
500 mA max
118 x 47 mm
Range of operating temperatures
-20...+55ºC
1R
OUT
Open collector output.
Output is pulled to
COM when turned on.
0-90% RH @ 0... +40 °C (non-condensing)
32.1.3.1.2 LED and Pin Functionality
C2, C1
Z1 - Z16
STATUS
A0
A1
A2
PGM output C1, C2 status – on/off
Zone Z1 - Z16 state – alarm/restore
EPGM1 micro-controller status
EPGM1 module address pins
N/A
N/A
32.1.3.1.3 Connector Functionality
C1, C2
Z1 - Z16
AUXAUX+
Y
G
COM
DC+
PGM output terminals
Security zone terminals
Negative power supply terminal for auxiliary equipment
Positive power supply terminal for auxiliary equipment
RS485 interface for communication (yellow wire)
RS485 interface for communication (green wire)
Negative power supply terminal
Positive power supply terminal
MANUAL ELDES ESIM364 V1.6
EN
151
50
C2
C1
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
STATUS
A0
A1
A2
C1 C2 COM Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 Z9 COM Z10 Z11 COM Z12 Z13COM Z14 Z15COM Z16 -AUX+ COM DC+ Y
G
51
C2
C1
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16
EPGM1
STATUS
A0
A1
A2
C1 C2 COM Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 Z9 COM Z10 Z11 COM Z12 Z13COM Z14 Z15COM Z16 -AUX+ COM DC+ Y
Z16
Z15
Z14
Z13
Z12
Z11
Z10
Z9
Z8
Z7
Z5
Z6
Z4
Z3
Z1
Z2
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
5,6 kΩ
RELAY
MODULE
G
AUX+
AUX-
G
Y
ESIM364
32.1.3.1.4 EPGM1 Address
ESIM364 system allows to connect up to 2 EPGM1 modules - each set under different address. The module address can be set by putting
or removing the jumper from the A0 pins implemented in horizontal position (see Fig. No. 50). Jumper combinations for different EPGM1
module address configuration are indicated in the table below.
Address Configuration
Jumper position
152
EN
Address
A0
Module 1
A0
Module 2
MANUAL ELDES ESIM364 V1.6
32.1.3.2. Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
2. Connect EPGM1 DC+ terminal to ESIM364 AUX+ terminal, EPGM1 COM terminal to ESIM364 AUX- terminal, EPGM1 Y and G termianls
must be connected to ESIM364 Y and G terminals respectively (see Fig. No. 51).
3. Connect the resistors and sensors to EPGM1 module according to the selected zone connection Type 1, Type 2 or Type 3 (see 2.3.2
Zone Connec­tion Types). If ATZ mode is enabled, please connect the resistors and sensors according to zone connection Type 1 or
Type 2.
4. Set the EPGM1 module address by putting or removing the jumper from the A0 pins (see 32.1.3.1.4. EPGM1 Address).
5. Power up ESIM364 system.
6. Upon successful startup indicator STATUS should be blinking indicating successful EPGM1 operation.
7. EPGM1 is ready for use with ESIM364 alarm system.
NOTE: ATZ mode is not supported by EPGM1 zones.
NOTE: When ATZ mode is disabled, all EPGM1 zones must be wired in accordance with zone connection type set up in the system software-wise i.e. Type 1, Type 2 or Type 3. If ATZ mode is enabled, EPGM1 zones can be wired in accordance with Type 1 or Type 2 only
(mixed combination of these two zone connection types is permitted), regardless of the set up zone connection type in the system.
For more details on multiple EPGM1 module wiring, please refer to 3.2.7. RS485
32.1.4.ELAN3-ALARM - Ethernet Communicator
Main features:
• Supported Ethernet connectivity: 10/100 Mbit.
• Enables Internet access on ESIM364 via Ethernet interface.
• Automated configuration.
ELAN3-ALARM is an add-on device designed to use with ESIM364 alarm system and operate in IP-based networks. The device is an Ethernet-based communicator that enables instant Internet access allowing to perform the following:
• Establish a communication between ESIM364 and EGR100 middleware, Kronos or SIA IP protocol-based monitoring station software.
• Connect ESIM364 to ELDES Smart Security platform.
• Configure ESIM364 remotely.
32.1.4.1.Technical Specifications
32.1.4.1.1 Electrical & Mechanical Characteristics
Power supply
10-24V 50Hz ~ 210mA max. / 10-24V
Dimensions
70x85x57 mm
Operating temperature range
-20…+55 °C
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
MANUAL ELDES ESIM364 V1.6
210mA max.
EN
153
32.1.4.1.2 Main Unit, LED Indicator & Connector Functionality
FRONT SIDE
RJ45
52
SIDE VIEW
USB
LAN
(green)
USB
RS232
DEF
LAN
(yellow)
RJ45
STATUS
CONNECT
F1
AC/DC
G
Y
RJ45
10/100Base-T Ethernet port
USB
Mini USB port for firmware update
DEF
Pins for fimware update
STATUS
Red light-emitting diode indicating
micro-controller status
RS485
Green light-emitting diode indicating RS485 connection status
F1
miniSMDC 0,5A fuse
AC/DC
Power supply terminals
G
RS485 interface for communication
(green wire)
Y
RS485 interface for communication
(yellow wire)
LAN
(green)
Green light-emitting diode indicating Ethernet activity
LAN
(yellow)
Yellow light-emitting diode indicating Ethernet status
32.1.4.2.Installation
ATTENTON: The wiring is permitted to be done only while ESIM364 system is completely powered down.
1.Connect AC/DC terminals to ESIM364 system’s AUX+ and AUX- terminals. Alternatively, you can power up the device by 10-24V AC or
DC power supply unit (see 32.1.5.1.1 Electrical & Mechanical Characteristics).
2. Connect G and Y terminals to ESIM364 system’s G and Y terminals respectively.
3. Connect ELAN3-ALARM to local area network router using the Ethernet cable.
53
ETHERNET ROUTER
RJ45
USB
ELAN3-ALARM
AC/DC
G Y
154
EN
A UX+
A UX-
G
Y
ESIM364
ELAN3-ALARM
MANUAL ELDES ESIM364 V1.6
4. Power up ELAN3-ALARM and wait until indicator STATUS starts flashing indicating successful micro-controller operation (see Fig. No.
52).
5.Indicator LAN (green) will flash indicating Ethernet connection activity, while indicator LAN (yellow) will be steady ON indicating
successful Ethernet connection (see Fig. No. 52).
6. In less than 1 minute indicator RS485 indicator will steadily light ON indicating the successfully established RS485 connection between ELAN3-ALARM device and ESIM364 system see (Fig. No. 52).
7. Once the device is up and running, it will automatically obtain a local IP address from the DHCP server, therefore manual configuration
of ELAN3-ALARM is necessary only if DHCP server is not supported by your internet service provider (ISP). For more details on ELAN3ALARM configuration, please refer to ELDES Configuration Tool software’s HELP section.
8. Configure ESIM364 system in order to use it with ELAN3-ALARM. For more details, please refer to ESIM364 installation manual and
ELDES Configuration Tool software’s HELP section.
NOTE: Ensure that the ELAN3-ALARM device is not being blocked on the router, otherwise the device will be unable to transmit any data.
To view or change the IP address of ELAN3-ALARM, please connect the device to the computer using the USB cable and ELDES Configuration
Tool software. For more details, please refer to ELDES Configuration Tool software’s HELP section.
32.1.4.3. Restoring Default Parameters
1. Disconnect the power supply.
2. Short circuit (connect) DEF pins.
3. Power up the device for 7 seconds.
4. Power down the device.
5. Remove short circuit from DEF pins.
6. Parameters restored to default.
32.1.4.4. Updating the Firmware via USB Cable
1. Power down the device.
2. Short-circuit (connect) the DEF pins.
3. Connect the device via USB cable to the PC.
4. Power up the device.
5. The new window must pop-up where you will find the .bin file. Otherwise open My Computer and look for Boot Disk drive.
6. Delete the .bin file found in the drive.
7. Copy the new firmware .bin file to the very same window.
8. Power down the device.
9. Unplug the USB cable.
10. Remove the short-circuit from DEF pins.
11. Power up the device.
12. Firmware updated.
32.1.5. 1-Wire Interface
1-Wire interface is used for the system to communicate with an iButton key reader and up to 8 temperature sensors. 1-Wire interface COM
and DATA terminals are ground and data respectively. When connecting single or multiple temperature sensors, the +5V terminal must be
used along.
For more details on 1-Wire device wiring, please refer to 32.2.1 iButton Key Reader and Buzzer
32.1.6. iButton Key Reader and Keys
The iButton key is a chip enclosed in a stainless steel tab usually implemented in a small plastic holder. Each iButton key holds a unique
identity code (ID) which is used for alarm system ESIM364 arming and disarming procedure.
Main iButton features:
• Up to 16 iButton keys per alarm system unit ESIM364;
• Communication via 1-Wire interface.
MANUAL ELDES ESIM364 V1.6
EN
155
32.1.6.1. Technical Specifications
32.1.6.1.1 Electrical & Mechanical Characteristics
Supported iButton key model
Communication interface
Maximum cable length for 1-wire communication
Maxim/Dallas DS1990A
1-Wire
up to 30 meters
32.1.6.1.2Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
2. Connect iButton key reader contact wires to 1-Wire interface on ESIM364 alarm system: COM and DATA terminals respectively.
DATA
COM
54
iButton
key reader
3. Power up ESIM364 alarm system.
4 iButton® key reader is ready for use with ESIM364 alarm system.
For more details on iButton key management, please refer to 11. iBUTTON KEYS.
32.2.Modules Interface
32.2.1. EPGM8 - Hardwired PGM Output Expansion Module
EPGM8 is a PGM output expansion module intended for using with alarm system ESIM364. This module allows to connect up to additional
8 electrical appliances.
Main EPGM8 features:
• PGM output expansion adding 8 additional PGM outputs;
• Compatible with ESIM364 alarm system
32.2.1.1. Technical Specifications
32.2.1.1.1 Electrical & Mechanical Characteristics
Power supply
Number of PGM outputs
EPGM8 PGM output circuit
10-24V
8
Maximum commuting PGM output values
Dimensions
Humidity
Range of operating temperatures
Voltage – 30V; current 500mA
40 x 55 x 15 mm
156
EN
100mA max
1R
OUT
Open collector output.
Output is pulled to COM
when turned on.
0-90% RH @ 0... +40 °C (non-condensing)
-20...+55ºC
MANUAL ELDES ESIM364 V1.6
32.2.1.1.2 Connector Functionality
PGM output terminals
Positive power supply terminal
Negative power supply terminal
55
12V GND
D1 - D8
12V
GND
D1 D2 D3 D4 D5 D6 D7 D8
MANUAL ELDES ESIM364 V1.6
EN
157
32.2.1.2. Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
S TA T
C4
C3
C2
C1
NE TW
56
GSM/GPRS ANT
C 4C 3
OPEN
W-LESS ANT
OPEN
2. Insert EPGM8 pins into appropriate ESIM364 alarm system slots (see Fig. No. 54)
G SM
MO DE M
DEF
MODULES
12V GND
EPGM8
ESIM364
FUSE F1
3A
PRG
USB
TIP RING
D1 D2 D3 D4 D5 D6 D7 D8
AK U +
AK U -
AC /DC
AC /DC
AUX+
AUXBELL+
BELL-
CO M
G
Y
C2
C1
BU Z +
BU Z MIC +
M IC +5V
DAT A
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
3. Connect EPGM8 12V positive power supply terminal with ESIM364 alarm system AUX+ terminal and EPGM8 GND terminal with
ESIM364 alarm system AUX- terminal. (see Fig. No. 55).
4. Connect the electrical appliances to D1 – D8 PGM outputs. (see Fig. No. 55).
57
ESIM364
AUX+
12V GND
AUX-
D1 D2 D3 D4 D5 D6 D7 D8
El. Appliance 1
TO AUX+
El. Appliance 2
TO AUX+
El. Appliance 3
TO AUX+
El. Appliance 4
TO AUX+
El. Appliance 5
TO AUX+
El. Appliance 6
TO AUX+
El. Appliance 7
TO AUX+
El. Appliance 8
TO AUX+
5. Power up ESIM364 alarm system.
6. Enable EPGM8 mode using EKB2, EKB3, EKB3W keypads or ELDES Configuration Tool software. For more details, please refer to
software’s HELP section or 18.2.1. EPGM8 Mode.
7. EPGM8 is ready for use with ESIM364 alarm system.
158
EN
MANUAL ELDES ESIM364 V1.6
32.2.2.EA1 – Audio Output Module
EA1 audio output module enables a duplex audio connection for ESIM364 alarm system.
Main EA1 features:
•
Two-way voice conversation during a phone call;
• Possibility to connect headphones or desktop speakers.
32.2.2.1. Technical Specifications
• 3,5 mm female jack
• Dimensions: 35 x 33 x 12 mm
32.2.2.2.Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
S TA T
C4
C3
C2
C1
NE TW
58
GSM/GPRS ANT
C 4C 3
OPEN
W-LESS ANT
OPEN
2. Insert EA1 pins into appropriate ESIM364 alarm system slots.
G SM
MO DE M
DEF
ESIM364
EA1
FUSE F1
3A
PRG
USB
MODULES
TIP RING
AK U +
AK U -
AC /DC
AC /DC
AUX+
AUXBELL+
BELL-
CO M
G
Y
C2
C1
BU Z +
BU Z MIC +
M IC +5V
DAT A
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
3. Connect headphones or desktop speakers to EA1 3,5 mm female jack.
59
EA1
4. Power up ESIM364 alarm system.
5. EA1 is ready for use with ESIM364 alarm system.
MANUAL ELDES ESIM364 V1.6
EN
159
32.2.3.EA2 – Audio Output Module with Amplifier
EA2 audio output module enables a duplex audio connection for ESIM364 alarm system.
Main EA2 features:
• Two-way voice conversation during a phone call;
• Possibility to connect a speaker.
32.2.3.1. Technical Specifications
• 1W 8Ω audio amplifier
• Dimensions: 41 x 40 x 24 mm
32.2.3.2.Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
S TA T
C4
C3
C2
C1
NE TW
60
C 4C 3
OPEN
W-LESS ANT
OPEN
2. Insert EA2 pins into appropriate ESIM364 alarm system slots.
GSM/GPRS ANT
G SM
MO DE M
DEF
FUSE F1
3A
PRG
USB
ESIM364
MODULES
TIP RING
EA2
AK U +
AK U -
AC /DC
AC /DC
AUX+
AUXBELL+
BELL-
CO M
G
Y
C2
C1
BU Z +
BU Z MIC +
M IC +5V
DAT A
CO M
Z6
CO M
Z5
Z4
CO M
Z3
Z2
CO M
Z1
3. Connect a speaker to EA2 Speaker terminals.
61
EA2
4. Power up ESIM364 alarm system.
5. EA2 is ready for use with ESIM364 alarm system.
160
EN
MANUAL ELDES ESIM364 V1.6
33.ELDES WIRELESS DEVICES
33.1. EKB3W - Wireless LED Keypad
EKB3W is a wireless LED keypad intended to use with ELDES alarm systems.
Main EKB3W features:
•
Alarm system arming and disarming (see 12.5. EKB3W Keypad and User Password).
•
Arming and disarming in Stay mode (see 15. STAY MODE).
•
System parameter configuration (see 5. CONFIGURATION METHODS).
•
PGM output control (see 18.4. Turning PGM Outputs ON and OFF).
•
Visual indication by LED indicators (see 33.1.5. Visual and Audio Indications).
•
Audio indication by built-in buzzer (see 33.1.5. Visual and Audio Indications).
•
Keypad partition switch (see 23.3. Keypad Partition and Keypad Partition Switch).
The system configuration by EKB3W keypad is performed by activating the Configuration mode (see 5. CONFIGURATION METHODS) and
entering the required parameters & values. ESIM364 system allows to connect up to 4 EKB3W keypads.
33.1.1. Technical Specifications
33.1.1.1. Electrical & Mechanical Characteristics
Battery type
Number of batteries
Battery operation time
Wireless transmitter-receiver frequency
Range of operating temperatures
Dimensions
Humidity
Wireless communication range
Compatible with alarm systems
1,5V Alkaline AAA type
3
~12 months*
868 Mhz (EU version) / 915 Mhz (US version)
-30...+55ºC
140 x 100 x 18 mm
0-90% RH @ 0... +40 °C (non-condensing)
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
* The operation time depends on different conditions and may vary.
33.1.1.2. LED Functionality
ARMED
READY
Steady ON - alarm system is armed / exit delay in progress; flashing - Configuration mode activated
Steady ON - system is ready – no violated zones and tampers
SYSTEM
BYPS
1-12
Steady ON - system faults; flashing - violated high-numbered zone (-s)
Steady ON - zone bypass mode
Steady ON - violated zone Z1-Z12
33.1.1.3. Keys Functionality
[BYPS]
[CODE]
[*]
Bypass violated zone
System fault list / violated high-numbered zone indication / violated tamper indication
Clear typed in characters
[#]
[0] ... [9]
[1]... [2]
[0]
[STAY]
[INST]
Confirm (enter) command
Command typing
Keypad partition switch
Simultaneous 4-partition arming
Manual system arming in Stay mode
1st character for Configuration mode activation/deactivation command
MANUAL ELDES ESIM364 V1.6
EN
161
33.1.1.4.Main Unit & Connector Functionality
BACK SIDE
FRONT SIDE
62
A
B
ARMED
READY
SYSTEM
1
BYPS
7
8
2
9
3
4
5
6
10
11
12
1
2
3
STAY
4
5
6
BYPS
7
8
9
INST
*
0
#
CODE
+
BATTERY
-
-
BATTERY
+
+
BATTERY
-
TAMPER
5,6 kΩ
Z1
TAMPER
+/-
Tamper-button for EKB3W
enclosure status monitoring
Battery slots
COM
Z1
COM
Common contact
Security zone terminal
33.1.2. Installation
1. Detach keypad holder from EKB3W front side . Keypad holder detach points are marked with arrows.
63
DOWN SIDE
BACK SIDE
2.
Fix the keypad holder on the wall using the screws.
3. Connect a sensor and the resistor across Z1 and COM terminalss in accordance with zone connection Type 1 or Type 2 (see 2.3.2. Zone
Connection Types). As keypad zone Z1 is disabled by default, it can be enabled by SMS, ELDES Configuration Tool, EKB2, EKB3 and
EKB3W keypad. Keypad zone Z1 must be enabled and resistor connected even if the tamper button alone is required (see Fig. No. 62).
NOTE: Keypad zone connection type can differ from selected on-board zone connection type.
NOTE: ATZ mode is NOT supported by keypad zones. ATZ mode is ineffective for keypad zones when enabled.
4. Remove the plastic tab inserted between one of the battery terminals and battery slots.
64
ATTENTION: Before fixing the keypad into the holder please , make sure that the tamper is properly pressed (see Fig. No. 62)..
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more
details. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move
EKB3W closer to alarm system device and bind it again.
7. Upon the successful binding process, the built-in mini buzzer of EKB3W device provides 3 short beeps and the system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EKB3W closer to alarm system device
and bind anew.
8. EKB3W keypad is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.1.6. Restoring Default Parameters for more details.
162
EN
MANUAL ELDES ESIM364 V1.6
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be 0,5
meters.
33.1.3. EKB3W Zone & Tamper
Upon successful EKB3W wireless LED keypad contact binding process, the system adds 1 wireless Instant zone intended for wired sensor con­
nection. By default, the keypad zone Z1 is disabled. The keypad zone can be enabled by SMS, EKB2 keypad, EKB3 keypad, EKB3W keypad and
ELDES Configuration Tool. software (see 14.9. Disabling and Enabling Zones). When Z1 is enabled, it operates like any other system zone,
therefore a sensor can be connected to it. In addition, Z1 and COM terminals must be connected with resistor of 5,6kΩ nominal.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EKB3W:
• By tamper button. EKB3W has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EKB3W
is illegally opened, the tamper button becomes unpressed (see Fig. No. 62). This action is followed by alarm which is sent by SMS text
message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EKB3W and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS message
contains the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
33.1.4.Battery Replacement
1. Open EKB3W enclosure.
2. Remove all 3 old batteries from the battery slots.
3. Postition the 3 new 1,5V alkaline AAA type batteries according to the appropriate battery slot positive/negative terminals indicated on
the PCB (printed-circuit-board) of EKB3W.
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 33.1.2. Installation.
ATTENTION: Only 1,5V Alkaline AAA type batteries can be used. Install only new, high quality and unexpired batteries. Do not
mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must
be taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not
charge, disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.1.5. Visual and Audio Indications
EKB3W keys have a LED back-light, which will be activated once any key is pressed. Due to battery power saving reasons, the back-light and
LED light last for 10 seconds after the last key-stroke.
The built-in buzzer uses two types of sound signals – three short beeps and one long beep. Three short beeps stand for successfully carried
out configuration command, one long beep – for invalid configuration command. The buzzer emits short beeps during exit delay. Due to battery saving reasons the buzzer will beep during entry delay and in case of alarm only if the violated zone is of the associated EKB3W keypad.
NOTE: The keypad will not activate any LED indicators, nor the back-light if not bound to the system.
For more details, please refer to 33.1.7. Wireless Communication, Sleep Mode and Back-light Timeout
33.1.6.Restoring Default Parameters
MANUAL ELDES ESIM364 V1.6
EN
163
1. Remove one battery from EKB3W.
2. Press and hold the [*] key.
3. Insert the battery back to EKB3W.
4. Hold the [*] key until LED READY starts flashing.
5. Wait until LED READY turns off and LED ARMED starts flashing.
6. Release the [*] key.
7. Parameters reset to default.
33.1.7. Wireless Communication, Sleep Mode and Back-light Timeout
Once the wireless device is bound, it will attempt to exchange data with ESIM364 system. The communication process follows this pattern:
1. Due to battery power saving reasons, most of the time EKB3W keypad operates in sleep mode and periodically wakes up (by default - every 60 seconds) to transmit the supervision signal, identified as Test Time, to the ESIM364 system. However, when the keypad wakes up,
it will NOT activate its buzzer and/or the LED indicators.
2. When any EKB3W key is pressed, the keypad LED indicators and the back-light will activate for a set up period of time (by default - 10
seconds), identified as Back-light Timeout. During the Back-light Timeout, the Test Time will automatically switch to 2 seconds period
allowing to indicate system alarms, faults and arm/disarm process on the EKB3W keypad if it is assigned to the same partition as the one
that is violated or being armed/disarmed (see 23. PARTITIONS).
3. The Back-light timeout will expire after 10 seconds (by default) of EKB3W idling. When the Back-light Timeout expires, the keypad will
light OFF the LED indicators and the back-light and return to sleep mode. Meanwhile:
a) if a zone or tamper, which is of the associated EKB3W keypad, is violated, EKB3W will instantly wake up and initiate the Back-light Timeout. Meanwhile the keypad buzzer will emit short beeps and the LED indicators will light ON indicating the violated zone or tamper
number.
b) if a zone or tamper, which is not of the associated EKB3W keypad, is violated, EKB3W keypad will NOT wake up and will NOT initiate the
Back-light Timeout as well as the buzzer will NOT emit short beeps and the LED indicators will NOT light ON.
To set a different Back-light Timeout value, please refer to the following configuration method:
Set Back-light
Timeout
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
For more details and how to set a different Test Time value, please refer to 19. WIRELESS DEVICES.
NOTE: Even if Back-light Timeout has expired, the character will be considered as type in once the appropriate EKB3W key is pressed.
164
EN
MANUAL ELDES ESIM364 V1.6
33.2.EW1 - Wireless Zone & PGM Output Expansion Module
Main EW1 features:
•
2 zones for wired sensor connection;
•
2 PGM outputs for electrical appliance connection;
•
Powered by external power supply.
Wireless expansion module EW1 is a wireless device with 2 zones and 2 PGM outputs. This expansion module connects to ELDES wireless
alarm systems and enables wireless access for to 2 wired devices such as movement PIR sensors, magnetic door contacts etc. In addition it
allows to connect and control up to 2 appliances, i.e. lighting, heating etc. After the wiring process to EW1 it is necessary to bind EW1 to the
alarm system by sending a corresponding command via SMS text message or using software ELDES Configuration Tool.
It is possible to connect up to 32 EW1 devices to ESIM364 alarm system at a time. The maximum wireless connection range is 150 meters (in
open areas).
33.2.1. Technical Specifications
33.2.1.1. Electrical & Mechanical Characteristics
Power supply
Number of zones
Zone connection type
Number of PGM outputs
Maximum commuting PGM output values
EW1 PGM output circuit
7-15V
20mA max
2
Normally closed (NC)
2
Voltage – 30V; current 500mA
Wireless transmitter-receiver frequency
Range of operating temperatures
Dimensions
Humidity
868 Mhz (EU version) / 915 Mhz (US version)
-20...+55ºC
38x60x12mm
Wireless communication range
Compatible with alarm systems
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
65
COM
Z2
1R
OUT
0-90% RH @ 0... +40 °C (non-condensing)
66
EW1
Z1
C2
LED
D1
D2
C1
Open collector
output.
Output is pulled to
COM when turned on.
DC+ C1 C2
Z1 Z2 COM
DC+
33.2.1.2. Connector & LED Functionality
COM
Z2, Z1
C2, C1
DC+
D1, D2
LED
Common terminal for power supply, zones
Security zone terminals
PGM output terminals
Positive power supply terminal
Pins for restoring default parameters
EW1 status
+12V
Power supply
MANUAL ELDES ESIM364 V1.6
EN
165
33.2.2.Installation
1. Disconnect ESIM364 alarm system main power supply and backup battery.
2. Wire up EW1 as indicated in Fig. No. 66.
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. T he system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EW1
closer to ESIM364 alarm system device and bind it again.
5. EW1 module is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.2.4 Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be
0,5 meters.
33.2.3.EW1 Zones, PGM Outputs & Tamper
Upon successful EW1 module binding process, the system adds 2 wireless Instant zones intended for wired sensor connection and 2 wireless
PGM outputs intended for electrical appliance connection and control.
The wireless connection loss between EW1 and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation
and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS message contains the wireless device model,
wireless ID code and tamper number.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
33.2.4.Restoring Default Parameters
1. Disconnect EW1 power supply.
2. Short circuit (connect) pins D1 and D2.
3. Power up EW1 and wait until LED provides several short flashes.
4. Disconnect power supply.
5. Remove short-circuit from D1 and D2 pins.
6. Power up EW1.
7. Parameters restored to default.
33.3.EWP1 – Wireless Motion Detector
Main EWP1 features:
•
Violated zone detection by built-in PIR movement sensor.
EWP1 is a wireless device with built-in PIR movement sensor and operates with ELDES wireless alarm systems. The user only needs to switch
on the EWP1 sensor and bind it to ESIM364 alarm system by sending a corresponding command via SMS text message or using soft­ware ELDES
Configuration Tool. User can also monitor temperature of the surrounding areas in real-time as EWP1 has a built-in temperature sensor. It is
possible to connect up to 32 EWP1 devices to ESIM364 alarm system at a time. The maximum wireless connection range is 150 meters (in
open areas).
33.3.1. Technical Specifications
33.3.1.1. Electrical & Mechanical Characteristics
Battery type
Battery voltage; capacity
Battery operation time
Wireless transmitter-receiver frequency
Range of operating temperatures
Dimensions
Humidity
ER14505 AA Lithium Thionyl Chloride
3,6 V; 2,4 Ah
~18 months*
868 Mhz (EU version) / 915 Mhz (US version)
-10 ... +55°C
104x60x33mm
Detection coverage angle
Maximum detection distance
Compatible with alarm systems
Wireless communication range
90°
10 meters
ELDES Wireless
Up to 30 meters in premises; up to 150 meters in open areas
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
166
EN
MANUAL ELDES ESIM364 V1.6
67
1
2
1
Motion detector
2
LED indicators informing about status of PIR sensor EWP1
3
TAMPER button automatically identifies when the box of sensor
EWP1 is open or closed
4
RESET button for reseting system parameters
5
ER14505 3,6 V Lithium Thionyl Chloride battery
3
4
5
33.3.2.Installation
1. Choose the place where intrusion into the premises is the most probable and install the device. To avoid false triggers of the system do
not install it in the following places:
• directing the lens to direct sunlight, for example, to the window of the premises;
• where there is a risk of sudden temperature alteration, for example, near a fireplace or heating system;
• where there is an enlarged possibility of dust or air flow;
• behind the curtain or some other cover blocking the detected zone.
68
2. Fix EWP1 sensors mounting holder with two screws to the wall and attach the sensor.
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWP1
closer to alarm system device and bind it again.
5. EWP1 is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.3.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be
0,5 meters.
33.3.3.EWP1 Zone & Tamper
Upon successful EWP1 sensor binding process, the system adds 1 wireless Instant zone intended for movement detection. By, default, the
alarm is caused instantly if any movement is detected in coverage area of the sensor (when system is armed).
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWP1 sensor:
• By tamper button. EWP1 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWP1 is
illegally opened, the tamper button becomes unpressed (see Fig. No. 67). This action is followed by alarm which is sent by SMS text
message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EWP1 and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
MANUAL ELDES ESIM364 V1.6
EN
167
ATTENTION: The tamper will not operate if the wireless zone is disabled.
33.3.4.Battery Replacement
1. Open EWP1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate battery slot positive/negative terminals indicated on the PCB (prin­ted-circuitboard) of EWP1.
4. Insert the battery into the battery slot.
5. Batteries replaced.
For more details, please refer to 33.3.2. Installation.
ATTENTION: Only ER14505 Lithium Thionyl Chlorid AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
33.3.5.Restoring Default Parameters
1. Remove any battery from EWP1.
2. Press and hold the RESET button.
3. Insert the battery back to EWP1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
33.4.EWD1 – Wireless Magnetic Door Contact
Main EWD1 features:
•
Violated zone detection by magnetic contact;
•
Panic button.
EWD1 is a wireless device with magnetic contact and panic button which is used to secure doors, windows or any other opening parts and
it operates with ELDES wireless alarm systems. EWD1 is bind to ESIM364 alarm system by sending a corresponding command via SMS text
message or using software ELDES Configuration Tool. When EWD1 is connected to the system, two wireless zones are added. First wireless
zone is used to monitor the magnetic contacts and the second wireless zone is for managing the panic button. By default panic button zone is
configured as Silent zone and in case the panic button is pressed, the system causes silent alarm (no siren is activated).
It is possible to connect up to 32 EWD1 devices to ESIM364 alarm system at a time. The maximum wireless connection range is 150 meters
(in open areas).
33.4.1.Technical Specifications
33.4.1.1.Electrical & Mechanical Characteristics
Battery type
Number of batteries
Battery operation time
Wireless transmitter-receiver frequency
Range of operating temperatures
Door contact dimensions
Humidity
CR2032 3V Lithium
1
15 months*
868 Mhz (EU version) / 915 Mhz (US version)
-20...+55ºC
60x37x18mm
Magnet dimensions
Wireless communication range
Compatible with alarm systems
60x17x16mm
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
168
EN
MANUAL ELDES ESIM364 V1.6
69
MAGNET
FRONT SIDE
BACK SIDE
1. BATTERY
2. LED
3. PANIC button
4. RESET button
5. PINS for firmware updates
6. TAMPER
+
1 2
3
4 5
6
33.4.2.Installation
1. Open EWD1 enclosure and insert the battery.
70
RESET
LED
+
3V
CR2032
+
2. EWD1 consists of two parts: a magnet and a sensor. Sensor components are: a mounting part and the sensor. Magnet components are:
a mounting part and the cover.
2.1 Fix the sensor mounting part with two screws on the door or window jamb.
2.2 Fix the magnet mounting part with two screws next to the sensor mounting part on door or window frame.
71
MAX 20 mm
NOTE: The distance between magnet and sensor can be up to 20 mm only.
2.3 The sensor should be attached to the fixed sensors mounting part. When attaching sensor pay attention to the tamper (micro switch)
- it must be pressed.
2.4 The magnet cover should be attached to the fixed magnet mounting part.
NOTE: It is not recommend to fix EWD1 in other ways than with screws, e.g. with duck tape. See Fig. No. 69 for the incorrect ways of
fixing the magnetic door contact.
72
3. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
4. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWD1
MANUAL ELDES ESIM364 V1.6
EN
169
closer to alarm system device and bind it again.
5. EWD1 magnetic door contact is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.4.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be
0,5 meters.
33.4.3.EWD1 Zones & Tamper
Upon successful EWD1 magnetic door contact binding process,the system adds 1 wireless Instant zone and 1 wireless Panic/Silent zone.
The wireless zones are applied to the following EWD1 components respectively:
• Magnetic contact - by default, causing alarm if doors/windows is opened when system is armed.
• Panic button - by default, causing silent alarm instantly when pressed.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWD1:
• By tamper button. EWD1 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWD1 is
illegally opened, the tamper button becomes unpressed (see Fig. No. 69). This action is followed by alarm which is sent by SMS text
message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
•
By wireless connection loss. The wireless connection loss between EWD1 and ELDES alarm system leads to alarm. The system identifies this
event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS message contains
the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
33.4.4.Battery Replacement
1. Open EWD1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate batte­ry slot positive terminal indicated.
4. Insert the battery into the battery slot.
5. Battery replaced.
For more details, please refer to 33.4.2. Installation.
ATTENTION: Only ER14505 Lithium Thionyl Chlorid AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
33.4.5.Restoring Default Parameters
1. Remove the battery from EWD1.
2. Press and hold the RESET button.
3. Insert the battery back to EWD1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
33.5.EWK1 - Wireless Keyfob
Main EWK1 features:
170
EN
MANUAL ELDES ESIM364 V1.6
•
Alarm system arming & disarming;
•
Panic button;
•
PGM output control;
•
Sound indication by built-in mini buzzer.
Keyfob EWK1 – is a wireless device intended to arm and disarm ESIM364 alarm system, to open and close the gates or to control any other device
connected to the alarm system. Wireless keyfob EWK1 is compatible with ELDES wireless alarm systems, therefore user can easily bind it to the
alarm system using ELDES Configuration Tool software or sending a corresponding SMS command. EWK1 keyfob features four configurable buttons intended to operate according to individual needs. After the button is pressed, EWK1 internal buzzer’s sound signal confirms a transferred
command to ESIM364 alarm system via wireless connection. The status of the sent command can be checked by attempting to receive the feedback signal from the alarm system. This can be performed by pressing down the same button and holding it for 3 seconds. 3 short sound signals
indicate a successfully carried out command while 1 long beep stands for failed command and feedback signal failure. By default one pair of
buttons is already configured to arm and disarm the alarm system.
The virtual zones of ESIM364 system are intended for EWK1 button configuration. Please, refer to software’s ELDES Con­figuration Tool HELP section
for more details.
73
Optional
functionality
Disarm the
system
Arm the
system
It is possible to connect up to 5 EWK1 devices to ESIM364 alarm system at
a time. The maximum wireless connection range is 150 meters (in open
areas).
Optional
functionality
NOTE: The picture above reflects the default EWK1 button configuration. All keyfob buttons are configurable according to individual needs.
33.5.1. Technical Specifications
33.5.1.1. Electrical & Mechanical Characteristics
Battery type
Battery voltage; capacity
Quantity of batteries
Battery operation time
Wireless transmitter-receiver frequency
Range of operating temperatures
Wireless keyfob dimensions
Humidity
CR2032 Lithium
3V; 240 mAh
1
~18 months*
868 Mhz (EU version) / 915 Mhz (US version)
-20...+55ºC
54 x 42 x 13 mm
Wireless communication range
Compatible with alarm systems
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
0-90% RH @ 0... +40 °C (non-condensing)
* The operation time depends on different conditions and may vary.
MANUAL ELDES ESIM364 V1.6
EN
171
33.5.2.Installation
75
74
1. Unscrew the EWK1 keyfob housing.
2. Open EWK1 keyfob housing.
3. Insert CR2032 battery provided in the EWK1 package.
Before inserting the battery, make sure that the battery’s “+” sign is facing the outer side.
76
+
3V
CR2032
+
4. Close and screw up the keyfob housing.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more
details.
6. While binding the device to the alarm system, press any EWK1 button several times.
7. EWK1 is ready to use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.5.5. Restoring Default Parameters for more details.
33.5.3.EWK1 Zones (Panic Button)
EWK1 keyfob supports a Panic Button feature allowing to cause alarm at any time when the specified button is pressed. This feature can be
configured using ELDES Configuration Tool software by creating a virtual zone of Panic/Silent or 24-Hour type and assigning it to Virtual Alarm
option. The Panic Button feature can be set up on any button of EWK1. For more details, please refer to software’s HELP section.
33.5.4.Battery Replacement
1. Open EWD1 enclosure.
2. Remove the old battery from the battery slot.
3. Postition the new battery according to the appropriate battery slot positive terminal indicated.
4. Insert the battery into the battery slot.
5. Battery replaced.
For more details, please refer to 33.5.2 Installation.
ATTENTION: Only CR2032 3V batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries
with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
172
EN
MANUAL ELDES ESIM364 V1.6
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.5.5.Restoring Default Parameters
1. Remove the battery from EWK1 keyfob.
2. Press and hold
button.
3. Insert the battery back to EWK1.
4. Hold the button pressed until LED indicator provides several short flashes.
5. Release
button.
6. Parameters restored to default.
33.6.EWS1 – Wireless Indoor Siren
Main EWS1 features:
•
Audio alarm indication by built-in speaker.
EWS1 is a wireless device with built-in siren speaker and operates with ELDES wireless alarm systems. EWS1 has to be bind to the alarm system by sending a corresponding SMS text message or using software ELDES Configuration Tool. Upon successful EWS1 binding, the system
adds one wireless zone and one wireless PGM output. The wireless zone is used to monitor the device (tamper - when the batteries are being
removed) and the wireless PGM output is used to control the speaker. In case of alarm, the siren provides a sound alarm for one minute. The
configuration of this parameter is disabled for EWS1 in order to save the battery power.
It is possible to connect up to 32 EWS1 devices to the alarm system at a time. The maximum wireless connection range is 150 meters (in open areas).
33.6.1.Technical Specifications
77
33.6.1.1. Electrical & Mechanical Characteristics
Compatible with alarm systems
Acoustic sound level
+
-
+
LED
RESET
BATTERY
Up to 30 meters in premises; up to 150 meters in open areas
ELDES Wireless
~97 dB measured at
1m
BATTERY
+
Wireless communication range
0-90% RH @ 0... +40 °C
(non-condensing)
-
BATTERY
Range of operating temperatures
Dimensions
Humidity
1,5V Alkaline AA type
3
~18 months*
868 Mhz (EU version)
/ 915 Mhz (US version)
-20...+55ºC
123x73x36mm
-
Battery type
Number of batteries
Battery operation time
Wireless transmitter-receiver frequency
* The operation time depends on different conditions and may vary.
33.6.1.2.Main Unit & LED Functionality
RESET
+/LED
Button for restoring default parameters
Battery slots
EWS1 status indication
MANUAL ELDES ESIM364 V1.6
EN
173
33.6.2.Installation
1.
Open EWS1 enclosure.
78
79
Insert a thin flat-shaped screwdriver or any tool alike into the gap located on the back of the enclosure.
Push the screwdriver down to the right carefully in order to detach
the enclosure parts from each other.
2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminals and battery slots.
80
3. Fix the siren on the wall using the screws.
81
-
RESET
BATTERY
LED
+
+
BATTERY
-
+
-
BATTERY
4. Close EWS1 enclosure. No tools are required for this action.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software.
Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWS1
closer to alarm system device and bind it again.
7. EWS1 siren is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.6.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be
0,5 meters.
174
EN
MANUAL ELDES ESIM364 V1.6
33.6.3.EWS1 Zone, PGM Output & Tamper
Upon successful EWS1 indoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless
zone is intended for EWS1 tamper control and the wireless PGM output is for siren control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. The wireless connection loss between EWS1
and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and
phone call to the user (-s) by default. The SMS message contains the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
ATTENTION: The siren will sound only if wireless zone of the siren is assigned to the same partition as the one that has been alarmed
(see 23.1. Zone Partition).
33.6.4.Battery Replacement
1. Open EWS1 enclosure.
2. Remove all 3 old batteries from the battery slots.
3. Postition the 3 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the
PCB (printed-circuit-board) of EWS1
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 33.6.2 Installation.
ATTENTION: Only CR2032 3V batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries
with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.6.5.Restoring Default Parameters
1. Remove any battery from EWS1.
2. Press and hold the RESET button.
3. Insert the battery back to EWS1.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
33.7.EWS2 – Wireless Outdoor Siren
Main EWS2 features:
•
Audio alarm indication by built-in speaker;
•
Visual alarm indication by built-in LED indicators;
•
Range of operating temperature: -30...+55oC.
EWS2 is a wireless outdoor device with a built-in siren speaker, LED indicators and operates with ELDES wireless alarm systems. EWS2 has to
be bind to the alarm system by sending a corresponding SMS text message or using software ELDES Configuration Tool. Upon successful EWS2
binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm, the siren provides a sound alarm for one
minute. The configuration of this parameter is disabled for EWS2 in order to save the battery power.
It is possible to connect up to 32 EWS2 devices to the alarm system at a time. The maximum wireless connection range is 150 meters (in open
areas).
MANUAL ELDES ESIM364 V1.6
EN
175
33.7.1. Technical Specifications
Battery type
Number of batteries
Battery operation time
Wireless transmitter-receiver frequency
Range of operating temperatures
Dimensions
Humidity
Wireless communication range
Compatible with alarm systems
Acoustic sound level
1,5V Alkaline AA type
4
~18 months*
868 Mhz (EU version) / 915 Mhz
(US version)
-30...+55ºC
201 x 140 x 36 mm
82
TAMPER
33.7.1.1. Electrical & Mechanical Characteristics
0-90% RH @ 0... +40 °C (non-condensing)
Up to 30 meters in premises; up to
150 meters in open areas
ELDES Wireless
~104 dB measured at 1 m
TAMPER
* The operation time depends on different conditions and may vary.
BATTERY
-
+
BATTERY
-
-
BATTERY
+
-
BATTERY
+
RESET
33.7.1.2. Main Unit, LED & Connector Functionality
RESET
+/LED indicators
Tamper
Bell+
Bell-
+ BELL
+
Button for restoring default parameters
Battery slots
Visual alarm indication
Tamper button terminals
Positive siren speaker terminal
Negative siren speaker terminal
33.7.2.Installation
1. Open EWS2 enclosure.
83
84
Remove the small blue lid located
on the front side of the enclosure by
pulling the lid up.
Unscrew the front side of the enclosureю
85
Detach the front side of the enclosure
by pulling the front side upю
2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminal and battery slots.
86
3. Fix the siren on the wall using the screws.
176
EN
MANUAL ELDES ESIM364 V1.6
87
+
BATTERY
-
+
BATTERY
-
-
BATTERY
+
-
BATTERY
+
4. Close EWS2 enclosure.
5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more
details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWS2
closer to alarm system device and bind it again.
7. EWS2 siren is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.7.6. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be
0,5 meters.
33.7.3.EWS2 Zone, PGM Output & Tamper
Upon successful EWS2 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless
zone is intended for EWS2 tamper control and the wireless PGM output is for siren control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWS2:
• By tamper button. EWS2 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWS2 is
illegally opened, the tamper button becomes unpressed (see Fig. No. 82). This action is followed by alarm which is sent by SMS text
message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS2 and ELDES alarm system leads to alarm. The system
identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
ATTENTION: The siren will sound only if wireless zone of the siren is assigned to the same partition as the one that has been alarmed
(see 23.1. Zone Partition).
33.7.4.Battery Replacement
1. Open EWS2 enclosure.
2. Remove all 4 old batteries from the battery slots.
3. Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the
PCB (printed-circuit-board) of EWS2
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 33.7.2 Installation.
MANUAL ELDES ESIM364 V1.6
EN
177
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.7.5.Restoring Default Parameters
1. 2. 3. 4. 5. 6. Remove any battery from EWS2.
Press and hold the RESET button.
Insert the battery back to EWS2.
Hold the RESET button until LED indicator provides several short flashes.
Release the RESET button.
Parameters restored to default.
33.8.EW1B - Battery-Powered Wireless Zone & PGM Output Expansion Module
Main EW1B features:
•
•
2 zones for wired sensor connection;
2 PGM outputs for electrical appliance connection.
Wireless expansion module EW1B is a wireless device with 2 zones and 2 PGM outputs. This expansion module connects to ELDES wireless
alarm systems and enables wireless access for to 2 wired devices such as movement PIR sensors, magnetic door contacts etc. In addition it
allows to connect and control up to 2 appliances, i.e. lighting, heating etc. After the wiring process to EW1B it is necessary to bind EW1B to the
alarm system by sending a corresponding command via SMS text message or using software ELDES Configuration Tool. t is possible to connect
up to 32 EW1B devices to ESIM364 alarm system at a time. The maximum wireless connection range is 150 meters (in open areas).
33.8.1.Technical Specifications
33.8.1.1.Electrical & Mechanical Characteristics
Battery type
Number of batteries
Battery operation time
Number of zones
Zone connection type
1,5V Alkaline AA type
3
~18 months*
2
Normally closed (NC)
Number of PGM outputs
EW1B PGM output circuit
2
Maximum commuting pgm output values
Wireless transmitter-receiver frequency
Wireless communication range
Voltage – 30V; current 500mA
868 Mhz (EU version) / 915 Mhz (US version)
Up to 30 meters in premises; up to 150 meters in open
areas
ELDES Wireless
-20...+55ºC
38x60x12mm
90x110x40mm
Compatible with alarm systems
Range of Operating Temperatures
EW1B PCB Dimensions
EW1B Enclosure Dimensions
Humidity
Enclosure rating
1R
OUT
Open Collector Output.
Output is pulled to COM
when turned ON.
0-90% RH @ 0... +40 °C (non-condensing)
IP65
* The operation time depends on different conditions and may vary.
178
EN
MANUAL ELDES ESIM364 V1.6
33.8.1.2.Connector & LED Functionality
COM
Common terminal for zones
Z2, Z1
Security zone terminals
C2, C1
PGM output terminals
D1, D2
Pins for restoring default parameters
LED
EW1B status
88
D1
D2
LED
COM
Z2
Z1
C2
C1
+ BATTERY –
– BATTERY +
+ BATTERY –
33.8.2.Installation
89
3. Remove the plastic tab inserted between one of the battery
terminals and battery slot terminals.
91
2. Detach the front side of the enclosure by pulling the front side
up.
90
4. Connect the circuit as indicated below.
92
EW1B
Z1 Z2 COM
Sensor
C1 C2
Sensor
1. Push down the screwdriver and turn it counter-clockwise to un­
screw EW1B enclosure.
6. Close EW1B enclosure.
7. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software.
Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more details.
8. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EW1B
closer to alarm system device and bind it again.
MANUAL ELDES ESIM364 V1.6
EN
179
9. EW1B is ready for use.
NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See
33.8.5. Restoring Default Parameters for more details.
ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM364 system can be 0,5
meters.
33.8.3. EW1B Zones, PGM Outputs & Tamper
Upon successful EW1B module binding process, the system adds 2 wireless Instant zones intended for wired sensor connection and 2 wireless
PGM outputs intended for electrical appliance connection and control. The wireless connection loss between EW1B and ELDES alarm system
leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s)
by default. The SMS message contains the wireless device model, wireless ID code and tamper number.
33.8.4.Battery Replacement
1. Open EW1B enclosure.
2. Remove all 3 old batteries from the battery slots.
3. Postition the 3 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals as indicated.
4. Insert the batteries into the battery slots.
5. Batteries replaced.
For more details, please refer to 33.8.2. Installation.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.8.5.Restoring Default Parameters
1. Remove any battery from EW1B.
2. Short circuit (connect) pins D1 and D2.
3. Insert the battery back to EW1B.
4. Wait untill LED provides several short flashes.
5. Remove short-circuit from D1 and D2 pins.
6. Parameters restored to default.
33.9.EWF1 - Wireless Smoke Detector
Main EWF1 features:
•
•
•
•
Photoelectric sensor for slow smouldering fires
TEST button
Non-radioactive technology for environmental friendly
High and stable sensitivity
•
•
•
•
Quick fix mounting plate for easy installation
LED operation indicator
Built-in speaker for audio alarm indication
Auto-reset when smoke clears
EWF1 is a wireless photoelctric type smoke detector intended to use with ELDES wireless alarm systems. Photoelectric smoke detectors
are generally more effective at detecting smouldering fires which smoulder for hours before bursting into flame. An optical method
is used for the detection of visible smoke. When the concentration of smoke in the optical chamber exceeds a given threshold, EWF1
sounds the alarm and sends out a signal to the ESIM364 alarm system using the wireless connection and the system triggers the alarm.
By default, when more than one EWF1 device is used, the system will automatically activate the interconnection feature (see 20.6.
In­terconnection). ESIM364 system support up to 32 EWF1 devices, The maximum wireless connection range is 150 meters (in open
areas).
180
EN
MANUAL ELDES ESIM364 V1.6
33.9.1.Technical Specifications
33.9.1.1. Electrical & Mechanical Characteristics
Detection type
Detector lifetime
photoelectric chamber
Alarm sound level
85 Decibels at 3 meters
9V
6LR61 alkaline
1
~18 months*
868 Mhz (EU version) / 915 Mhz (US version)
Up to 30 meters in premises; up to 150 meters in open areas
5oC to 45oC
0-90% RH @ 0... +40 °C (non-condensing)
3.0-6.0 % Obs /m
110mm Ø
eLDES Wireless
~98 dB measured at 1 m
up to 10 years**
Battery voltage
Battery type
Number of batteries
Battery operation time
Wireless transmitter-receiver frequency
Wireless communication range
Range of operating temperatures
Humidity
Sensitivity to smoke
Dimensions
Compatible with alarm systems
Acoustic sound level
* The operation time depends on different conditions and may vary.
** For more details regarding date of replacement, please refer to the label located on the back side of the device.
33.9.1.2.Main Unit & LED Functionality
TEST
LED
SIREN
RESET**
Button for testing / button for testing and restoring default parameters (if RESET button not available)
EWF1 status indication
Built-in speaker for audio alarm indication
Button for restoring default parameters
93
FRONT SIDE
Siren
BACK SIDE
TEST button
LED indicator
RESET button**
BATTERY
** Unavailaible on some EWF1 models
33.9.2.PLACEMENT
1. Install the wireless smoke detector as close to the center of the ceiling as possible. If this is not practical, mount no closer than 10
centimeters from a wall or corner. Also, if local codes allow, install wireless smoke detectors on walls, between 10 and 30 centimeters
from ceiling/wall intersections.
2. Install a minimum of two wireless smoke detectors in every house, no matter how small the house is.
3. Install a wireless smoke detector in each room that is divided by a partial wall (either coming down from the ceiling at least 20 centimeters, or coming up from the floor).
4. Install a wireless smoke detector in lived-in attics or attics which ho use electrical equipment like furnaces, air conditioners, or heaters.
NOTE: For best protection we recommend that you install a wireless smoke detector in every room.
MANUAL ELDES ESIM364 V1.6
EN
181
Recommended EWF1 placement locations
94
(0,1 m)
Ceiling
RE
HE A
YW RE
AN HIS A
T
IN
0,9 m (3 ft)
Acceptable
here
NEVER
HERE
(0,1 m)
Max.
(0,3 m)
Max.
Top of detector
acceptable here
0,9 m (3 ft)
HORIZONTAL DISTANCE
Wall
NOTE: Measurements shown are to the closest edge of the detector.
Typical Single-Story House
Install a wireless smoke detector on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area. If a
bedroom area hallway is more than 9 meters long, install a wireless smoke detector at each end.
If there is a basement: Install a wireless smoke detector on the basement ceiling at the bottom of the stairwell.
95
Bedroom
Bedroom
Living Room
Family Room
LEGEND:
Dining Room
Kitchen
Bedroom
Minimum required smoke
detector locations.
Recommended additional
smoke detector locations
182
EN
MANUAL ELDES ESIM364 V1.6
Typical Multi-Story or Split-Level House
Install a wireless smoke detector on the ceiling or wall inside each
bedroom and in the hallway outside each separate sleeping area. If
a bedroom area hallway is more than 9 meter long, install a wireless smoke detector at each end. Please install a wireless smoke
detector on the top of a first-to-second floor stairwell.
96
Bedroom
LEGEND:
Bedroom
Minimum required smoke detector locations.
Recommended additional smoke detector locations
Living
Room
Dining
Room
Basement
Incorrect EWF1 Placement
DO NOT place EWF1 in the following locations:
•
•
•
•
•
Near appliances or areas where normal combustion regularly occurs (kitchens, near furnaces, hot water heaters). Use specialized
wireless smoke detector with unwanted alarm control for this areas.
In areas with high humidity, like bathrooms or areas near dishwashers or washing machines. Install at least 3 meters away from these
areas.
Near air returns or heating and cooling supply vents. Install at least 1 meter away from these areas. The air could blow smoke away
from the detector, interrupting its alarm.
In rooms where temperatures may fall below 5oC or rise above 45oC.
In extremely dusty, dirty, or insect-infested areas where loose particles interfere with wireless smoke detector operation.
ATTENTION: Incorrect placement will result in a decrease of operational effectiveness.
33.9.3.Installation
1. Detach the mounting plate by turning it counter-clockwise from
the back of EWF1 (see Fig. No. 97).
2. Secure the mounting plate to ceiling or wall with mounting
screws.(see Fig. No. 97).
3. Lift to open the battery pocket door (see Fig. No. 97).
4. Insert the battery into the battery pocket considering the polarity terminals indicated on the enclosure of EWF1. Ensure the
battery is securely connected. Red LED may flash briefly when
the battery is being installed.
5. Close the battery pocket door by snapping it into place.
6. Position the smoke detector to the mounting plate by turning
it clockwise to lock into place. Note that the device will not lock
into the mounting plate without the battery being present in
the battery pocket.
7. Push the TEST button to verify if the wirless smoke detector is
operational. See 33.9.5.1. Testing EWF1.
8. Bind the device to the alarm system by sending a corresponding
command via SMS text message or using ELDES Configuration
Tool software. Please, refer to the software‘s HELP section or
refer to 19.1. Binding, Removing and Replacing Wireless
Devices for more details.
6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to
move EWF1 closer to alarm system device and bind it again.
10. EWF1 wireless smoke detector is ready for use.
97
Mounting plate
Mounting slot
Screws
Battery pocket door
NOTE: If you are unable to bind the wireless device, please restore the parameters of the wireless device to default and try again. See chapter 33.9.6. Restoring Default Parameters for more details.
MANUAL ELDES ESIM364 V1.6
EN
183
33.9.4.Interconnection
The interconnection feature automatically links all wireless smoke detectors resulting in causing an instant alarm in the system along
with the rest of EWF1 wireless smoke detectors. For more details on interconnection feature and how to manage it, please refer to 20.4.
EWF1 Interconnection.
33.9.5.Maintenance
33.9.5.1.Testing EWF1
•
The TEST button verifies if EWF1 is operational. Firmly push the TEST button and the wireless smoke detector will sound a loud beep.
The alarm will stop sounding after releasing the TEST button. When testing EWF1 using ELDES Configuration Tool software, the
detector will provide short beeps.
•
Stand at arm’s length from the wireless smoke detector when testing.
•
Test wireless smoke detectors weekly and upon returning from vacation or when no one has been in the household for several days.
•
Test each wireless smoke detector to be sure it is installed correctly and operating properly.
•
DO NOT use an open flame to test this wireless smoke detector. You may ignite and dam­age the wireless smoke detector or your
home.
•
If the wireless smoke detector does not sound, please check the battery and signal level using ELDES Configuration Tool software.
ATTENTION: Test all wireless smoke detectors weekly to ensure proper operation.
33.9.5.2.Battery Replacement
1. Turn EWF1 counter-clockwise to detach it from the mounting
plate.
98
2. Gently pull down the wireless smoke detector.
9V battery
3. Remove the old battery from the battery pocket.
4. Postition the new 9V battery according to the appropriate
battery slot positive/negative terminals indicated on the
enclosure of EWF1. Ensure the plastic battery holder is fully
depressed when the battery has been fitted.
5. Using the TEST button, test the wireless smoke detector to
verify if it is operational. See 33.9.5.1. Testing EWF1.
6. Re-attach the wireless smoke detector to the mounting plate
by turning the wireless smoke detector clockwise until it snaps
into place.
ATTENTION: Only 9V 6F22 primary alkaline type battery can be used. Install only new, high quality and unexpired batteries.
ATTENTION: The battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
NOTE: The system sends an SMS message to the preset user phone number as soon as the battery level runs below 5%.
33.9.6. Restoring Default Parameters
1. Remove the battery from EWF1.
2. Press and hold the RESET button.
3. Insert the battery back to EWF1.
4. Hold the RESET button until you hear a short beep.
5. Release the RESET button.
184
EN
MANUAL ELDES ESIM364 V1.6
On some EWF1 models the RESET button is not available. On such EWF1 devices the reset process is as follows:
1. Remove the battery from EWF1.
2. Wait for 1 minute or more.
3. Press and hold the TEST button.
4. Insert the battery back to EWF1.
5. Hold the TEST button for 10 seconds or more.
6. Release the TEST button.
ATTENTION: EWF1 built-in speaker will sound while pressing and holding the TEST button. Please, ignore the sound.
33.9.7. Cleaning
Clean the wireless smoke detector at least once a month to remove dust, dirt, or debris. Using the soft brush or wand attachment of a
vacuum cleaner, vacuum all sides and cover of wireless smoke detector. Be sure all the vents are free of debris.
If necessary, use a damp cloth to clean wireless smoke detector cover.
NOTE: Do not attempt to remove the cover to clean inside the wireless smoke detector. This will void your warranty.
33.10. EWK2/EWK2A - Wireless Keyfob
Main Features:
•
•
•
•
Alarm system arming & disarming;
Panic button;
PGM output control;
Visual and audio indication of command status.
For more details, please refer to ELDES alarm system user and installation manuals.
EWK2/EWK2A is a wireless device intended to remotely arm and disarm ELDES alarm system, cause system alarm (Panic Button) or to
control any electric appliance connected to the alarm system’s PGM output. In order to start using wireless keyfob EWK2/EWK2A, it has to
be bound to ELDES wireless alarm system using ELDES Configuration Tool software or sending a corresponding SMS text message. EWK2
keyfob features four configurable buttons intended to operate according to individual needs,while EWK2A keyfob model features one configurable button. After the button is pressed, EWK2/EWK2A internal buzzer’s sound signal and red LED indicator confirms a transferred
command to ELDES alarm system via wireless connection. The status of the sent command can be checked by attempting to receive the
feedback signal from the alarm system. This can be performed by pressing down the same button again and holding it for 3 seconds. 3
short sound signals and LED indicator flashes indicate a successfully carried out command, while 1 long beep and LED indicator flash stands
for failed command and feedback signal failure. By default, one pair of buttons is already configured to arm and disarm the alarm system.
It is possible to connect up to 5 EWK2/EWK2A devices to ELDES alarm system at a time. The maximum wireless connection range is 150
meters (in open areas).
33.10.1. Technical specifications
EWK2
EWK2A
LED
indicator
99
LED
indicator
Arm the
system
Disarm the
system
Optional
functionality
Panic button
Optional
functionality
NOTE: the picture above reflects the default EWK2/EWK2A button configuration. All EWK2 keyfob buttons are/EWK2A keyfob button is
configu-rable according to individual needs.
MANUAL ELDES ESIM364 V1.6
EN
185
33.10.1.1. Electrical & Mechanical Characteristics
Battery type
CR2032 Lithium
Battery voltage; capacity
3V; 240 mAh
Quantity of batteries
1
Battery operation time
~18 months*
Wireless transmitter-receiver frequency
868 Mhz
Range of operating temperatures
-20...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Dimensions
53 x 37 x 10 mm
Wireless communication range
Up to 30 meters in premises; up to 150 meters
in open areas
Compatible with alarm systems
ELDES Wireless
* This operation time can be achieved by pressing the keyfob button up to 4 times per day. The operation time depends on different conditions and may vary.
33.10.2. Installation
1. Remove the screw located on the back side of EWK2/EWK2A enclosure.
100
2. Once the enclosure is opened, remove the PCB from the EWK2/EWK2A enclosure and flip the PCB so that the back side would be facing
up.
101
EWK2
102
EWK2A
3. Insert the CR2032 type battery provided in the EWK2/EWK2A pack. Before inserting the battery, ensure that it is positioned plusmarked side up.
103
104
4. Insert the CR2032 type battery provided in the EWK2/EWK2A package. Before inserting the battery, ensure that it is positioned plusmarked side up.
186
EN
MANUAL ELDES ESIM364 V1.6
105
BATTERY
CR2032
+
5. Insert the PCB back to the enclosure and close it.
6. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
7. Press any EWK2 button/press the EWK2A button several times until the device is successfully bound.
8. EWK2/EWK2A is ready for use.
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. See
chapter 33.10.5. Restoring Default Parameters for more details.
MANUAL ELDES ESIM364 V1.6
EN
187
33.10.3. Panic Button
by default, EWK2A keyfob supports a Panic Button feature allowing to cause an alarm at any time when the keyfob button is pressed.
EWK2 keyfob may support a Panic Button feature. This feature that can be configured using ELDES Configuration Tool software by creating a virtual zone of Panic/Silent or 24-Hour type and assigning it to Virtual Alarm option. The Panic Button feature can be set up on any button of EWK2.
33.10.4. Battery Replacement
1. 2. 3. 4. 5. Open EWK2/EWK2A enclosure.
Remove the old battery from the battery slot.
Postition the new battery according to the appropriate battery slot positive terminal indicated.
Insert the battery into the battery slot.
Battery replaced.
See 33.10.2 installation for more details.
ATTENTION: Only CR2032 3V battery can be used. Install only new, high quality and unexpired batteries.
ATTENTION: The battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
33.10.5. Restoring Default Parameters
EWK2
1. Press and hold
and
buttons simultaneously.
2. Hold the buttons pressed until LED indicator and the buzzer provide several short flashes and beeps simultaneously.
3. Release the buttons.
4. Parameters restored to default.
EWK2A
1. Press and hold the lower side of the button.
2. Hold the button pressed until LED indicator and the buzzer provide several short flashes and beeps simultaneously.
3. Release the button.
4. Parameters restored to default.
33.11. EWD2 - Wireless Door Contact/Shock Sensor/Water Sensor
Main EWD2 features:
•
Built-in shock sensor
•
2 wireless zones
•
Available zone modes: magnetic door contact, shock sensor, water sensor, digital sensor
•
2 built-in tamper switches: on the front and on the back of the PCB
EWD2 is a wireless device intended to secure doors, windows or any other opening/clsoing mechanisms. In addition, the device comes
equiped with a built-in shock sensor for vibration detection, an on-board zone terminal designed for external digital sensor or water sensor
connection and 2 built-in tamper switches for EWD2 sabotage detection. In order to start using EWD2, it has to be bound to ELDES alarm
system using ELDES Configuration Tool software or by sending a corresponding SMS text message to ELDES alarm system.
It is possible to connect up to 32 WD2 devices to ESIM364 alarm system. The maximum wireless connection range is 150 meters (in open
areas).
188
EN
MANUAL ELDES ESIM364 V1.6
33.11.1. Technical Specifications
33.11.1.1. Electrical & Mechanical Characteristics
Batteries
1,5V Alkaline AAAA type, LR8 (IEC standard) / 25A (ANSI/NEDA standard)
Number of batteries
2
Battery operation time
~18 months*
Wireless transmitter-receiver frequency
868 Mhz (EU version) / 915 Mhz (US version)
Wireless communication range
Up to 30 meters in premises; up to 150 meters in open areas
Range of operating temperatures
-20...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
EWD2 dimensions
101 x 22 x 20 mm
Magnet dimensions
47 x 17 x 10 mm
Compatible with alarm systems
ELDES Wireless
33.11.1.2. Main Unit and LED Functionality
* The operation time depends on different conditions and may vary.
106 FRONT SIDE
+
Z
COM
+
TAMP1
-
RESET
LED
DETECT
BACK SIDE
TAMP2
DETECT
Unit
Description
Z
Zone terminal
COM
Common terminal
TAMP1
Tamper switch
+/-
Battery slots
DETECT Magnet detector
LED
Light-emitting diode for indication of parameter restoring to default
RESET
Button for restoring default parameters
TAMP2
Tamper switch
ATTENTION for EWD2 v1 and EWD2 v2: If no sensor is to be connected to EWD2 on-board zone terminal, please make a short-circuit
(connect) Z and COM terminals in order to avoid the unnecessary battery power usage.
MANUAL ELDES ESIM364 V1.6
EN
189
33.11.2. Installation
1. Remove the cover of EWD2 enclosure.
107
108
Press and hold
Insert a screwdriver or
any other tool and push it down
2. Remove the PCB (printed-circuit-board) from the enclosure.
109
a) Press and hold
b) Pull up the edge
of the PCB
3. Screw in the enclsoure to the door or window jamb.
110
MOUNTING POINT A
MOUNTING POINT B
Ensure to screw in properly for supervision
of the back side by tamper switch
4. Wire up the external digital sensor (if any) or water sensor (if any) to Z and COM terminals, otherwise do not perform any wiring.
5.
Insert the PCB back into the enclosure
111
112
113
6. Remove the cover of the magnet enclosure.
190
EN
MANUAL ELDES ESIM364 V1.6
114
b) Pull up here
a) Insert a screwdriver or any
other tool and push it down
7. Screw in the magnet to the door or window frame and ensure that the magnet is fixed at the same height as the EWD2 magnet detector.
115
116
+
-
+
RESET
LED
20 mm max
8. Cover the magnet. No tools are required for this action.
9. Remove the plastic tab inserted between one of the battery terminals and battery slots of EWD2.
117
10. Close EWD2 enclosure. Insert the cover to the left edge of the enclosure’s bottom part and push the cover down. DO NOT use any tools
for this action.
118
ATTENTION: DO NOT attempt to close EWD2 enclosure the other way round, otherwise you might break it.
11. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
12. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWD2
closer to alarm system device and bind it again.
13. EWD2 is ready for use.
ATTENTION: Ensure that EWD2 device is properly fixed to the wall and the Mounting Point B portrayed in Fig. No. 110 is properly screwed
in. Otherwise, the tamper switch will NOT supervise the back side of EWD2 enclosure (see also 33.11.3. EWD2 Zones and Tampers).
MANUAL ELDES ESIM364 V1.6
EN
191
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again. See
33.11.5. Restoring Default Parameters for more details.
33.11.3. EWD2 Zones and Tampers
Upon successful EWD2 magnetic door contact binding process, the system adds 2 wireless Instant zones. The wireless zones can be set up
to operate under one of the following modes each:
•
•
Zone 1:
•
Magnetic door contact – Designed for causing an alarm (by default) if doors/windows are opened when the system is armed.
•
External sensor – Designed for causing an alarm (by default) if the wired digital sensor, connected to Z and COM terminals, is
triggered when the system is armed. This mode does NOT operate with Water sensor mode on Zone 2 simultaneously.
Zone 2:
•
Shock sensor – Designed for causing an alarm (by default) if the built-in shock sensor is triggered.
•
Water sensor – Designed for causing an alarm (by default) if a water sensor, connected to Z and COM terminals, is triggered. This
mode does NOT operate with External sensor mode on Zone 1 simultaneously.
Possible zone mode combinations:
•
Zone 1: Magnetic door contact + Zone 2: Shock sensor
•
Zone 1: Magnetic door contact + Zone 2: Water sensor
•
Zone 1: External Sensor + Zone 2: Shock sensor
•
Zone 1: Magnetic door contact + Zone2: N/A
•
Zone 1: External Sensor + Zone2: N/A
•
Zone 1: N/A + Zone 2: Shock sensor
•
Zone 1: N/A + Zone 2: Water sensor
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation
on EWD2:
•
By tamper switch. EWD2 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
•
one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 106).
•
the other one located on back of the PCB supervising the back side of the enclosure in case the EWD2 is illegally detached from
the wall (see Fig. No. 106).
Once the enclosure of EWD2 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
•
•
By wireless connection loss. The wireless connection loss between EWD2 and ELDES alarm system leads to alarm. The system
identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if both wireless zones are disabled.
For more details on EWD2 zone and tamper configuration, please refer to ELDES Configuration Tool software’s HELP section.
33.11.4. Battery Replacement
1. Open EWD2 enclosure.
2. Remove both old batteries from the battery slots.
3. Insert the 2 new 1,5V Alkaline AAAA type batteries according to the appropriate battery slot positive/negative terminals indicated on
the PCB of EWD2.
4. Batteries replaced.
See 33.11.2. Installation for more details.
ATTENTION: Only 1,5V Alkaline AAAA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old
batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken
when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble,
heat or incinerate old batteries.
ATTENTION: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.
ATTENTION: The battery status can be monitored in real-time using ELDES Configuration Tool software.
192
EN
MANUAL ELDES ESIM364 V1.6
33.11.5. Restoring Default Parameters
1. Remove any battery from EWD2.
2. Press and hold the RESET button.
3. Insert the battery back to EWD2.
4. Hold the RESET button until LED indicator provides several short flashes.
5. Release the RESET button.
6. Parameters restored to default.
33.12. EWS3 - Wireless Indoor Siren
Main features:
• Audio alarm indication by 2 built-in speakers.
• Visual alarm indication by built-in LED indicators: burglary/24-hour/tamper alarm and fire alarm indicated in different colours.
• 2 tamper switches: for enclosure opening and device detachment from the wall detection.
EWS3 is a wireless indoor device with built-in siren speakers and LED indicators operating with ELDES wireless alarm systems. The de­
vice is designed to notify the user by audio and visual signals in the event of alarm as well as in event of system arming/disarming (Bell
Squawk feature must be enabled). In the event of burglary, 24-hour or tamper alarm, EWS3 will activate the speakers and flash the blue
LED indicators, while in case of a fire alarm, the device can flash the red LED indicator (both features require EWS3 Alarm LED and EWS3
Fire Alarm LED parameters to be enabled using ELDES Configuration Tool software or EKB2/EKB3/EKB3W keypad)
To start using EWS3, it has to be bind to ELDES alarm system by sending a corresponding SMS message or using software ELDES Configuration Tool. Upon successful EWS3 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm,
the siren provides a sound alarm for one minute. The configuration of this parameter is disabled for EWS3 in order to save the battery
power.
It is possible to connect up to 32 EWS3 devices to ESIM364 alarm system. The maximum wireless connection range is 150 meters (in open
areas).
33.12.1. Technical Specifications
33.12.1.1. Electrical & Mechanical Characteristics
Battery type
1,5V Alkaline AA type
Number of batteries
4
Battery operation time
~18 months*
Wireless transmitter-receiver frequency
868 Mhz
Range of operating temperatures
-25...+55ºC
Humidity
0-90% RH @ 0... +40 °C (non-condensing)
Dimensions
167 x 80 x 34 mm
Wirelesscommunication range
Up to 30 meters in premises; up to 150 meters in open areas
Compatible with alarm systems
ELDES Wireless
Acoustic sound level
~90 dB measured at 1 m
* The operation time might vary in different conditions.
33.12.1.2. Main Unit, LED & Connector Functionality
-
BATTERY
BACK SIDE of PCB
TAMPER
+
+
BATTERY
-
-
BATTERY
+
119
TAMPER
BUZZER
-
BUZZER
BATTERY
+
FRONT SIDE of PCB
STATUS
ALARM (blue)
ALARM (red)
ALARM (blue)
RESET
MANUAL ELDES ESIM364 V1.6
EN
193
RESET
Button for restoring default parameters
+/-
Battery slots
STATUS
LED indicator for data transmission indication
ALARM (blue)
Blue LED indicators for visual alarm indication
ALARM (red)
Red LED indicator for visual alarm indication
BUZZER
Speakers for audio alarm indication
TAMPER
Tamper switches
FRONT SIDE of ENCLOSURE
120
ALARM (blue)
ALARM (red)
ALARM (blue)
LED indication
Description
ALARM (blue) flashing
Burglary, 24-Hour or tamper alarm in progress
ALARM (red) flashing
Fire alarm in progress
33.12.2. Installation
1. open EWS3 enclosure.
121
a. Press and hold
b. Pull down
2. Once the enclosure is opened, fix the siren to the wall using the screws.
MOUNTING POINT B
MOUNTING POINT A
-
123
MOUNTING POINT A
Ensure to screw in properly for supervision of the back side by tamper switch
+
+
-
-
+
-
+
122
MOUNTING
POINT B
3. Remove the plastic tab inserted between one of the battery terminals and battery slot contacts.
194
EN
MANUAL ELDES ESIM364 V1.6
The wireless connection loss between EWS3 and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
124
4. STATUS indicator should start flashing indicating successful data transmission.
5. Close EWS3 enclosure by putting the cover back.
6. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
7. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move
EWS3 closer to alarm system device and bind it again.
ATTENTION: Ensure that EWS3 device is properly fixed to the wall and the Mounting Point A portrayed in Fig. No. 122 and Fig. No.
123 is properly screwed in. Otherwise, the tamper switch will NOT supervise the back side of EWS3 enclosure (see also 33.12.3. EWS3
Zone, PGM Output and Tamper).
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again.
See chapter 33.12.5. Restoring Default Parameters for more details.
33.12.3. EWS3 Zone, PGM Output and Tamper
Upon successful EWS3 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The
wireless zone is intended for EWS3 tamper control and ability to assign a partition (-s), while the wireless PGM output is intended for siren
speaker control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation on EWS3:
• By tamper switch. EWS3 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
• one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 119).
• the other one located on back of the PCB supervising the back side of the enclosure in case the EWS3 is illegally detached from the
wall (see Fig. No. 119).
Once the enclosure of EWS3 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS3 and ELDES alarm system leads to alarm. The system identifies this event as a tamper violation and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
33.12.4. Battery replacement
1.
open EWS3 enclosure.
2.
Remove all 4 old batteries from the battery slots.
3.
Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated
on the PCB (printed-circuit-board) of EWS3
4.
Insert the batteries into the battery slots.
5.
Batteries replaced.
See chapter 33.12.2. Installation for more details.
ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the
old batteries with the new ones.
ATTENTION: At least 1 battery must be removed if the device is not in use.
MANUAL ELDES ESIM364 V1.6
EN
195
ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be
taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge,
disassemble, heat or incinerate old batteries.
NOTE: The system sends an SMS message to a preset user phone number as soon as the battery level runs below 5%.
NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.
5.12.1. Restoring default parameters
1. Remove one battery from EWS3.
2. Press and hold the RESET button.
3. Insert the battery back to EWS3.
4. Hold the RESET button until LED indicator starts blinking.
5. Release the RESET button.
6. Parameters reset to default.
196
EN
MANUAL ELDES ESIM364 V1.6
34.SERVICE MODE
The system comes equipped with Service mode allowing to carry out system maintenance tasks, such as detection device replacement,
tamper switch installation, wireless device battery replacement without causing zone or tamper alarm when Service mode is activated. To
activate/deactivate Service mode, please refer to the following configuration methods:
Activate Service
mode
SMS
SMS text message content:
ssss_SERVICEMODE:ON
Value: ssss - 4-digit SMS password.
Example: 1111_SERVICEMODE:ON
EKB2
Menu path:
OK → iiii → OK → SERVICE MODE → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Deactivate Service
mode
Enter parameter 67 & parameter status value:
67 1 #
Example: 671#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
SMS
SMS text message content:
ssss_SERVICEMODE:OFF
Value: ssss - 4-digit SMS password.
Example: 1111_SERVICEMODE::OFF
EKB2
Menu path:
OK → iiii → OK → SERVICE MODE → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W
Config
Tool
Enter parameter 67 & parameter status value:
67 0 #
Example: 670#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
NOTE: Alternatively, the Service mode automatically deactivates when 1-hour timeout period expires or after arming the system.
35.REMOTE SYSTEM RESTART
In some critical situations, a system restart may be required. To remotely carry out system restart, please refer to the following configuration method.
Restart the system
MANUAL ELDES ESIM364 V1.6
SMS
SMS text message content:
ssss_RESET
Value: ssss – 4-digit SMS password.
Example: 1111_RESET
EN
197
36.EN 50131-1 GRADE 3
EN50131-1
GRADE 3
ESIM364 system complies with EN 50131-1 Grade 3 security standard requirements and comes equipped with the following
features:
• 6-digit SMS password, user/master and installer codes.
• Prompt for master and installer codes when configuring the system by EKB2, EKB3, EKB3W keypad or ELDES Configuration
Tool software.
• System arming is blocked if any system fault exists. The user will not be able to arm the system until all existing system
faults are solved.
• System arming is blocked until tamper fault is cleared by the installer.
By default, the EN 50131-1 Grade 3 features are disabled. To enable/disable them, pelase refer to the following configuration methods:
Set 6-digit format for SMS password,
user/master and installer codes
Config
Tool
Set 4-digit format for SMS password,
user/master and installer codes
Config
Tool
Prompt for master and installer codes when
configuring the system by EKB2, EKB3, EKB3W
keypad or ELDES Configuration Tool software
Config
Tool
Prompt for installer code when configuring the
system using ELDES Configuration Tool software
Config
Tool
Deny system arming if any system fault exists
Config
Tool
Permit system arming if any system fault exists
Config
Tool
Clear tamper fault
EKB2
EKB3/
EKB3W
Config
Tool
198
EN
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
This operation may be carried out from the PC using the
ELDES Configuration Tool software.
Menu path:
OK → iiii → OK → CLEAR TAMPER FAULT → OK
Value: iiii – 4-digit installer code.
Enter parameter 22:
22 #
Example: 22#
This operation may be carried out from the PC using the ELDES Configuration Tool software.
MANUAL ELDES ESIM364 V1.6
37.SMART SECURITY
ELDES Smart Security is a cloud-based platform providing a user-friendly graphical interface intended for system status monitoring and
control. The solution consists of:
Android aplication/widget
or iOS application
Eldes device
Web interface
• ELDES device – The following ELDES devices come or can be equipped with ELDES Smart Security:
• ESIM364
• EPIR2
• ESIM120
• any other ELDES device on request
• Android application/widget and iOS application – The graphical interface can be accessed via a smart-phone application developed for Android and iOS-based (iPhone, iPad) devices.
• Web interface – ELDES Smart Security grants access to the device configuration (ESIM120) and user administration options as well as
all features mentioned above when accessed via a web-browser.
• ELDES Smart Security cloud server – The server links all ELDES Smart Security components to each other.
ELDES Smart Security solution allows to perform the following*:
• Arm/disarm the system
• Control gates or any other electric appliance connected to the output of the ELDES device
• View system faults and alerts
• Monitor GSM signal strength, back-up battery level and temperature
• Configure ELDES device
* - depends on the ELDES device in use. For more details on the available features, please refer to ELDES device user manual.
User hierarchy
Distributor
Power-Admin
Administrator
For more details on Smart Security solution, please refer Smart Security manual located at www.eldes.lt/download
MANUAL ELDES ESIM364 V1.6
EN
199
38.TECHNICAL SUPPORT
38.1.Troubleshooting
Indication
Possible reason
Indicator STAT is off
· No main power supply
· Wiring done improperly
· Blown fuse
Indicator NETW is off or flashing
·
·
·
·
·
·
·
Missing SIM card
PIN code is enabled
SIM card is inactive
Disconnected antenna
GSM network signal too weak
Problems with GSM provider
Microcontroller is not started due to electrical mains noise or static discharge
System does not send any SMS text messages
and/or does not ring
·
·
·
·
·
SIM card credit balance depleted
Incorrect SMS centre phone number
No GSM network signal
User number is not added (or control from anu phone number is disabled)
SIM card changed before disconnecting main power supply or backup battery
Received SMS text message “Wrong syntax”
· Incorrect SMS text message structure
· Extra space symbol could be left in SMS text message
Missing temperature indication in Info SMS text
message/EKB2 keypad
· Temperature sensor not connected
· Temperature sensor broken
· Connection wires too long
24H and/or Fire zones do not work
· Specified zone must be enabled by SMS, ELDES Configuration Tool, EKB2, EKB3
or EKB3W
No sound during remote listening
· Microphone not connected
· Improper microphone connection
For product warranty repair service please , contact your local retail store where this product was purchased.
If your problem could not be fixed by the self-guide above, please contact your local distributor. More up to date information about your device and other products can be found at the manufacturer’s website www.eldes.lt
38.2.Restoring Default Parameters
1. Disconnect the power supply and backup battery.
2. Short circuit (connect) DEF pins.
3. Power up the device for 7 seconds.
4. Power down the device.
5. Remove short circuit from DEF pins.
6. Parameters restored to default.
38.3. Updating the Firmware via USB Cable Locally
1. Disconnect the power supply and backup battery.
2. Short circuit (connect) DEF pins.
3. Connect the device via USB cable to the PC.
4. Power up the device.
5. The new window must pop-up where you will find the .bin file. Otherwise open My Computer and look for Boot Disk drive.
6. Delete the .bin file found in the drive.
7. Copy the new firmware .bin file to the very same window.
8. Power down the device.
9. Unplug USB cable.
10. Remove short circuit from DEF pins.
11. Power up the device.
12. Firmware updated.
NOTE: It is strongly recommended to restore default parameters after the firmware update.
200
EN
MANUAL ELDES ESIM364 V1.6
38.4.Updating Firmware via GPRS Connection Remotely
ATTENTION: The system will NOT send any data to monitoring station while updating the firmware remotely via GPRS network. However, during the firmware update process, the data messages are queued up and transmitted to the monitoring station after the firmware
upgrade process is over.
Before updating the firmware remotely via GPRS connection, make sure that:
• SIM card is inserted into SIM CARD1 slot of ESIM364 device (see 2.2. Main Unit, LED & Connector Functionality).
• Mobile internet service (GPRS) is enabled on the SIM card.
• Power supply is connected to ESIM364.
• Default SMS password is changed to a new 4-digit password (see 6. SMS PASSWORD AND INSTALLER CODE).
• At least User 1 phone number is set up (see 8. USER PHONE NUMBERS).
• APN, user name and password are set up (see 30.2.1. GPRS Network and ELAN3-ALARM).
Initiate FOTA
ESIM364 alarm system supports FOTA (firmware-over-the-air) feature. This allows to upgrade the firmware remotely via GPRS connection. Once the upgrade process is initiated, the system connects to the
specified FTP server address where the firmware file is hosted and begins downloading and re-flashing
the firmware. The firmware file must be located in a folder titled Firmware. In order to initiate the upgrade process please , send the following SMS message.
SMS
SMS text message content:
XXXX_FOTA:ftp-server-ip,port,firmware-file-name.bin,user-name,password
Value: ssss - 4-digit SMS password; ftp-server-io - public IP address of FTP server where
EPIR firmware file is stored; port - port number of FTP server (usually - 21); firmware-filename.bin - name of the firmware file, allowed max. length - up to 31 character; user-name
- user name of FTP server login, allowed max. length - up to 31 character; password password of FTP server login, allowed max. length - up to 31 character.
Example: 1111_FOTA:84.15.143.111,21,ESIM364fw bin,eldesuser,eldespassword
ATTENTION: Comma character is NOT allowed to use in user name and firmware file name.
ATTENTION: “ELDES UAB” does not run a FTP server and does not host the firmware files online. Please, contact your local distributor to
request the latest firmware file: [email protected]
NOTE: It is strongly recommended to restore default parameters after the firmware update.
38.5.Frequently Asked Questions
Question
Answer
Yes, ESIM364 device can fully operate without any SIM card inserted. In this case
1. Can ESIM364 operate as standalone device without SIM
you will not be able to configure and control the device by SMS and calls nor to
card inserted?
receive any SMS reports and calls.
Due to security reasons it is recommended to restore the violated zone (-s)
2. I am unable to arm the alarm system when one of the
before arming the alarm system. However, you can enable a Force attribute
zones (some zones) is violated, although I was able
or use the Bypass feature in order to arm the alarm system despite the vioto perform disarming. Is there a way to arm the alarm
lated zone (-s) being present. Please, refer to 14.5. Zone Type Definitions
system while the zone is violated?
and 14.7. Bypassing and Activating Zones.
3. I have activated ATZ mode in ELDES Configuration Tool
It appears that your ELDES Configuration Tool software is outdated. Please,
software, but I am unable to set the connection Type 5.
download the latest ELDES Configuration Tool software version by visiting
Whenever I select Type 5 and press the “Write Settings”
www.eldes.lt/en/download.
button it switches back to Type 4. What’s wrong?
4. When ESIM364 fully powers down my configuration
This might have happened due to the jumper left on DEF pins or it is a hardbecomes lost and I have to re-configure the device
ware failure. Please, remove the jumper if it is present on DEF pins or contact
again. What’s wrong?
your supplier for warranty service.
If the smoke detector is connected to one of the ESIM364 PGM outputs
5. I have a smoke detector connected to ESIM364 system. you can reset it by turning the PGM output OFF and then back ON. This
How do I reset the smoke detector when the “Fire” zone can be performed by SMS, EKB2 keypad, EKB3 keypad, EKB3W keypad and
is violated?
ELDES Configuration Tool software. Please, refer to 18.4. Turning PGM
Outputs ON and OFF.
6. What happens if I switch backup battery pole terminals Switching backup battery pole terminals places is forbidden. Otherwise this
places?
will lead to blown fuse and ESIM364 alarm system will have to be repaired.
The SMS reports on tamper violation can be disabled by EKB2, EKB3, EKB3W
7. How do I disable SMS reports and calls in case of tamper
keypads or ELDES Configuration Tool software. For mor details, please refer
violation when alarm system is disarmed?
to 16. TAMPERS or to the software’s HELP section. However, due to security
reasons it is not recommended to disable this feature.
MANUAL ELDES ESIM364 V1.6
EN
201
Question
Answer
8. Is any additional configuration necessary when conNo additional configuration is required in order to make EPGM1 module
necting EPGM1 module after wiring is done accroding to
operational.
EPGM1 user manual?
No, the number of EPGM1 zones does not duplicate in ATZ mode as
9. Does the number of EPGM1 zones duplicate when ATZ
EPGM1 module does not support ATZ mode. Only ESIM364 zones
mode is activated in the system?
duplicate in ATZ mode.
10. I connect the wired siren to ESIM364 and I hear a silent
sound alarm even when the alarm system is disarmed.
Please, connect the resistor of 3,3 kΩ nominal to the BELL- / BELL+ contacts
In case of alarm system alarm the siren provides a loud
This should solve the problem.
sound alarm as it should. Why?
11. I am using Windows operating system. The windows
Please, update ELDES Configuration Tool software by visiting www.eldes.lt/
of ELDES Configuration Tool are not fully displayed and
en/download and downloading the latest version.
some parts are like cut-off. What’s wrong?
12. The buzzer remains active when I disarm the alarm
The buzzer is intended for iButton indication only and it is not related to
system using the keypad. Why?
disarming process by keypad.
This happens due to wireless connection loss. There might be several reasons:
1. ELDES wireless device is installed too close or too far from ESIM364
13. One of wireless devices connected to ESIM364 system
system.
sends a tamper alarm from time to time, although no
2. Interference of other electronic equipment.
tamper was violated. Why?
3. Physical interference (building walls, floors etc.)
4. Metal material interference.
14. I have connected a wired magnetic door sensor, but
This happens due to incorrect resistor connection. Please, refer to correI receive tamper alarm instead of zone alarm. What’s
sponding connection circuit according to the selected zone connection type
wrong?
(Type 1 – 5). See 2.3.2 Zone Connection Types for more details.
By default, this notification is enabled. The system checks the backup
15. I disconnected the backup battery, but did not receive
battery resistance once a day and sends an SMS report to User 1 on backup
any SMS report on this event. How do I enable SMS
battery replacement if more than 2Ω resistance is detected. For more details,
report on backup battery disconnection?
please refer to 21. BACKUP BATTERY, MAINS POWER SUPPLY STATUS
MONITORING AND MEMORY.
Every time an SMS text message is sent to the user, the system must “know”
that the message was successfully delivered. The only way to partly disable the
16. When I check system SIM card credit balance I see a lot
SMS delivery report (for alarm notifications only) is to enable alarm SMS notificaof SMS delivery confirmation reports. How do I disable
tions to all users. This is useful when having only User1 phone number set up, as
SMS delivery confirmation ESIM364 system?
in case of alarm the system sends the alarm SMS text message to all preset users
simultaneously, but does not require any SMS delivery report.
According to GSM standards 1 SMS text message may consist of up to 160
17. I have set zone names and/or PGM output names
Latin alphabet/English characters maximum. If the message contains at
containing some Cyrillic and/or non-English characters. least one non-latin/non-English character, the length of SMS message beThe zone names and PGM output names do not fully fit comes at least half shorter, since those characters occupy more size of the
in the SMS message. What‘s wrong?
SMS text message than the Latin ones. It is recommended not to use any
non-Latin/ non-English characters in zone names and PGM output names.
18. The configuration of added wireless keyfob EWK1 to
ELDES Configuration Tool version is too old. Please, update it.
ESIM364 system is not visible in ELDES Configuration
Tool. What‘s wrong?
Microsoft .NET Framework v3.5 is not installed in Windows system. Please,
19. I am unable to run ELDES Configuration Tool - I receive
download this package from official Microsoft website free of charge and
error messages in Windows. Why?
install it to your Windows system.
20. Info SMS report comes with wrong date and time. How
do I correct it?
Please, set the correct system date and time using either ELDES Configuration Tool, EKB2, EKB3, EKB3W or SMS text message.
It appears that the device is unable to establish a communication with
configuration / FTP server. Please, check the GPRS settings in ESIM364
configuration (APN, user name, password), the location of the firmware
21. I receive an error message when attempting to
..bin file (must be located in the FTP server folder titled Firmware) and
configure the device or update the firmware remotely.
the mobile internet feature presence on the SIM card used with ESIM364.
Whats wrong?
If this does not solve the problem, please contact your GSM operator (and
ISP - for remote configuration problems) in order to request a list of blocked
TCP ports.
1. Send the ssss_endconfig SMS text message.
22. I waited for at least 5 minutes, but did not receive any
2. In ELDES Configuration Tool software press Disconnect button and
SMS message confirming that remote configuration via
repeat the steps from the beginning as described in 5.4. ELDES ConfiguGPRS connection has stopped. What‘s wrong?
ration Tool Software
23. The SMS password is changed and I have User 1 phone Most likely you have wrong character encoding set up in your SMS text
number added. However, whenever I send a text mes- messaging settings on your smart-phone. Please, ensure that you have
sage, such as XXXX INFO the system always replies
GSM Alphabet selected, NOT Unicode or any other type of character
with „Wrong password“. What‘s wrong?
encoding.
202
EN
MANUAL ELDES ESIM364 V1.6
39.RELATED PRODUCTS
EKB2 - LCD keypad
EKB3 - LED keypad
ME1 - metal cabinet
EPGM1 - hardwired zone and PGM output expansion module
EPGM8 - hardwired PGM output expansion module
EA1 - audio output module
MANUAL ELDES ESIM364 V1.6
EN
203
204
EN
EA2 - audio output module with amplifier
DS1990A-F5 - iButton key
DS18S20 - temperature sensor
ED1T - plastic enclosure with iButton key reader
and temperature sensor
EWP1 - wireless PIR sensor (motion detector)
EWD1 - wireless magnetic door contact
EWS2 - wireless external siren
EWS1 - wireless internal siren
MANUAL ELDES ESIM364 V1.6
EWK1 - wireless keyfob
EWF1 – wireless smoke detector
EW1 - wireless zone and PGM output expansion module
EW1B - battery-powered wireless zone and
PGM output expansion module
EKB3W – wireless LED keypad
EWD2 - wireless door contact/shock sensor
MANUAL ELDES ESIM364 V1.6
EWK2 - wireless keyfob
EWS3 - wireless indoor siren
EN
205
206
EN
MANUAL ELDES ESIM364 V1.6
MANUAL ELDES ESIM364 V1.6
EN
207
Made in the European Union
www.eldes.lt
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement