High security lock for safes - M

High security lock for safes - M
MiniTech
High security lock for safes
USER INSTRUCTIONS
Index
Information about MiniTech .......................................................................................... 3
Open the lock................................................................................................................ 5
Manager (01) and users (02-09): open the lock with time delay ............................ 5
Override user (10): open the lock without time delay............................................. 5
Change code ................................................................................................................ 6
Manager (01), users (02-09) and override user (10).............................................. 6
Users management ...................................................................................................... 6
Lock setup .................................................................................................................... 6
Dynamic codes ............................................................................................................. 7
Block and unblock the lock ........................................................................................... 7
Test mode..................................................................................................................... 8
Change language ......................................................................................................... 8
Audit.............................................................................................................................. 8
Download the audit on a Dallas key....................................................................... 8
Slide events on the LCD ........................................................................................ 9
Firmware release .......................................................................................................... 9
Adjust contrast .............................................................................................................. 9
Time delay .................................................................................................................. 10
Master menu............................................................................................................... 10
Time and date settings ........................................................................................ 10
Time Lock settings............................................................................................... 10
Weekly Time Lock settings - Add new values...................................................... 11
Weekly Time Lock settings – Verify or delete values........................................... 11
Closing periods settings - Add new values .......................................................... 12
Closing periods settings – Verify or delete values ............................................... 12
Opening periods settings- Add new values.......................................................... 13
Opening periods settings - Verify or delete values .............................................. 13
Audit .................................................................................................................... 14
Download the audit on a Dallas key..................................................................... 14
Slide events on the LCD ...................................................................................... 14
Change Master code ........................................................................................... 14
Manager Management......................................................................................... 14
Dynamic codes .................................................................................................... 15
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 19
2 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Information about MiniTech
Using your keypad
Press any button to power up the keypad.
Automatic power savings: if no operation is performed for 30 seconds the keypad will
automatically switch off.
To slide menu functions press
.
To exit from a menu and get back to start menu slide the functions until the message
.
“EXIT?” and press
Shortcuts
Press and hold the button corresponding to the needed function.
= Change Manager code (01), users code (02-09) and override user code (10)
= Users management
= Lock setup
= Dynamic codes
= Block/unblock the lock
= Test mode
= Change keypad language
= Audit
= Firmware release
= Time delay
= Back to start menu
= Master menu
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
3 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Users properties and default codes
Master: code (default: 1-2-3-4-5-6-7-8).
Manager: code (default: ID: 0-1 code: 1-2-3-4-5-6) or code + Dallas key.
Users 02 - 09: code (default: ID: 0-2 code: 2-2-2-2-2-2, ID 0-3 code: 3-3-3-3-3-3,
etc…), code + Dallas key.
Override user 10: code (default: ID 1-0 code: 1-0-1-0-1-0), code + Dallas key.
Change default codes before operating the lock
Penalty
Four consecutive wrong codes initiate a four minutes penalty. During this period LCD
will display the message “PENALTY” and no operation will be allowed.
Time Delay
Time delay 0-99 minutes; open window 1-19 minutes.
Dallas keys
Available as option for Manager and users (not available for Master).
Power supply
Lock can be powered with an ALKALINE 9V battery, with an internal large battery box
(6 ALKALINE 1.5V batteries) or with power supply and dedicated interface.
Low battery warning
A long beep and the message “BATTERY LOW” indicate the battery is low and has to
be immediately changed.
Audit
The lock stores the last 900 operations with time, date, user and operation. The
keypad stores the last 250 operations with time, date, user and operation.
Never remove label on lock cover, this voids the warranty.
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 19
4 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Open the lock
Manager (01) and users (02-09): open the lock with time delay
Power up the keypad. LCD will display the message:
Enter Manager or user code and the Dallas key (if set). LCD will show
time delay counting.
If the entered code is wrong LCD will display the message:
To stop time delay counting press
and then
to confirm.
After time delay counting LCD will display open window counting:
Press
, LCD will display the message:
ENTER CODE
XX–XXXXXX
TIME DELAY
00:59
WRONG CODE
STOP TIME DELAY
COUNTING?
OPEN WINDOW
00:01
ENTER CODE
XX–XXXXXX
Enter Manager or user code and the Dallas key (if set). Open within
three seconds (green led).
OPEN THE LOCK
If the user is set to open in dual mode LCD will display the message:
ENTER 2° CODE
XX–XXXXXX
Enter second code and the Dallas key (if set). Open the lock within
three seconds (green led).
OPEN THE LOCK
Override user (10): open the lock without time delay
Power up the keypad. LCD will display the message:
ENTER CODE
XX–XXXXXX
Enter override user code and the Dallas key (if set). Open the lock
within three seconds (green led).
OPEN THE LOCK
If the user is set to open in dual mode LCD will display the message:
ENTER 2° CODE
XX–XXXXXX
Enter second code and the Dallas key (if set). Open the lock within
three seconds (green led).
OPEN THE LOCK
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
5 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Change code
Manager (01), users (02-09) and override user (10)
Power up the keypad. Press and hold
message:
ENTER OLD CODE
XX–XXXXXX
. LCD will display the
Enter the old code and the Dallas key (if set).
ENTER NEW CODE
XXXXXX
Enter the new code and the Dallas key (if set).
CONFIRM CODE
XXXXXX
Confirm the new code and the Dallas key (if set).
Always perform this operation with the door open.
Users management
Power up the keypad. Press and hold
message:
USERS MANAGEMENT
01–XXXXXX
. LCD will display the
Enter Manager code.
Press
02 03 04 05 06
v x _ _ v
to slide users list or enter user ID.
“V” user installed, “_” user deleted, “X” user disabled.
Users 02 - 09 open with time delay (if set). Override user 10 opens without time delay. Override
user 10 can be only installed when lock is open. Open the lock before install the user.
Press
02
. If the user is not installed LCD will display the message:
INSTALL?
“ ” code, “ ” Dallas key, “+” dual mode, “TL” time lock
Press
to confirm or press
to disable/enable/delete and press
to confirm.
Lock setup
Lock setup is done through a setup Dallas key when the lock is in pre-setup.
To open a lock in pre-setup press
.
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 19
6 of 16
PRESS 1 TO OPEN
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Power up the keypad. Press and hold
message:
. LCD will display the
Enter the setup Dallas key into the reader and connect the reader the
the keypad through the jack connector. LCD will display the message:
Check displayed time and date, press
to confirm or
to update
the values and then
to confirm. LCD will display the message:
If the operation is successfully performed LCD will display the
message:
SYSTEM SETUP
…..
08:00 FRY
27/01/2006
UPLOADING
..…
OPERATION DONE
Dynamic codes
Power up the keypad. Press and hold
message:
. LCD will display the
Enter the dynamic user PIN or the Dallas key. LCD will display the
message:
Enter the dynamic code and press
DYNAMIC USER
XXXX
DYNAMIC CODE
XXX XXX XXX
.
Open within three seconds (green led).
If the lock is set to display closing code, LCD will display the
message:
CLOSING CODE
XXX
Block and unblock the lock
Power up the keypad. Press and hold
message:
. LCD will display the
BLOCK THE LOCK
XX–XXXXXX
Enter the requested code.
If weekly Time Lock is set LCD will display the next opening time.
BLOCK LOCK UNTIL
14/09 08:00
If you want to set a different opening time enter new values (max. 2
to confirm.
weeks) then press
BLOCK LOCK UNTIL
DD/MM hh:mm
BLOCK THE
LOCK?
LCD will display the message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
7 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Press
LOCK BLOCKED
to confirm. LCD will display the message:
The lock can be blocked for maximum thirtyone (31) days.
To unblock a lock previously blocked press and hold
display the message:
UNBLOCK THE LOCK
XX–XXXXXX
. LCD will
OPERATION DONE
Enter requested code. LCD will display the message:
Depending on lock setup Master code could be needed: enter Master code.
Test mode
Power up the keypad. Press and hold
message:
. LCD will display the
Enter the sequence of buttons displayed on the LCD.
TEST MODE
1234567890
v
TEST MODE
1234567890
v
Any working button will produce a short beep.
A damaged button will cause a long beep. LCD will display the
message.
WRONG/FAULTY
KEY
Change language
Power up the keypad. Press and hold
message:
. LCD will display the
ITALIANO
1 2 3
Press one of the available numbers to change the language and
press
to confirm or press
ENGLISH
1 2 3
to exit.
Audit
Download the audit on a Dallas key
Use this function to download on a Dallas key all keypad and lock events. The audit stored on the
Dallas key can be read through an interface and a PC software provided by Tecnosicurezza.
Power up the keypad. Press and hold
message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
. LCD will display the
ver. 1.0 2012 11 19
8 of 16
LOCK AUDIT
01–XXXXXX
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Enter Manager code. LCD will display the message:
Enter the audit Dallas key into the reader. If the operation is
successfully performed LCD will display the message:
ENTER DALLAS
…
OPERATION DONE
Slide events on the LCD
Use this function to check all the opening and closing events stored on the lock.
Power up the keypad. Press and hold
message:
. LCD will display the
Enter Manager code. LCD will display the message:
LOCK AUDIT
01–XXXXXX
ENTER DALLAS
…
Press
or wait. LCD will display the message:
LCD will start showing all the opening and closing events stored on
the lock.
Press
to slide all the events or
SLIDE EVENTS
ON LCD
001: 28/09
WED
14:42:48
to exit.
Firmware release
Power up the keypad. Press and hold
message:
Press
. LCD will display the
MINITECH
V 1.00
21/02/12
. LCD will display the
MINITECH
V 1.00
21/02/12
to get back to start menu.
Adjust contrast
Power up the keypad. Press and hold
message:
Press and hold
again. LCD will display the message:
Press one of the available numbers to change the contrast and press
to exit.
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
9 of 16
ADJUST CONTRAST
1 2 3 4 5 6 7 8
to confirm or press
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Time delay
Power up the keypad. Press and hold
message:
. LCD will display the
SET TIME DELAY
01–XXXXXX
Enter Manager code. LCD will display current values:
TIME DELAY
00
OPEN WINDOW 01
Press
T.DELAY
O.WINDOW
to exit or
to set new values.
Enter new values and press
message:
to confirm. LCD will display the
mm
mm
VALUES UPDATED
Time delay: 00 - 99 minutes. Open window: 01 - 19 minutes.
To set a lower time delay than the current set, lock must be open.
Master menu
. LCD will display the
MASTER MENU
XXXXXXXX
Access the Master menu and access the function. LCD will display
the message:
TIME AND DATE
SETTINGS
Power up the keypad. Press and hold
message:
Enter Master code. (default 1-2-3-4-5-6-7-8).
Time and date settings
Press
. LCD will display current time and date:
Press
to change time and date.
Enter new values and press
08:00 FRY
27/01/2006
hh:mm
___
DD / MM / YYYY
to confirm.
Time Lock settings
Access the Master menu and access the function. LCD will display
the message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 19
10 of 16
TIME LOCK
SETTINGS
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Weekly Time Lock settings - Add new values
Access the time lock menu and access the function. LCD will display
the message:
Press
. LCD will display the message:
Press
. LCD will display the current day of the week.
WEEKLY TIME LOCK
SETTINGS
ADD NEW VALUES
hh:mm
FRY
hh:mm
Enter first the opening time and then the closing time.
Press
to confirm. LCD will display the next day of the week and propose the same values.
Press
to confirm or
to skip and change day.
At the end of the week LCD will display the message:
Press
to save or
END OF LIST
EXIT AND SAVE? v
to get back to the first day.
Settings will be saved when
day.
will be pressed. Up to four different periods can be set for each
Weekly time lock is an opening time period: the safe door can be opened if you enter a valid code
(for ex. opening period from 08:00 to 14:00: the door can be opened from 08:00 to 14:00, but can’
be opened at 16:00).
You can enter four different time periods for each day (for ex. MON from 07:00 to 10:00; from
12:00 to 13:00; from 15:00 to 16:00; from 18:00 to 19:00).
Time periods will be saved after confirmation (pressing
).
It is recommended to set the values with safe door open.
Weekly Time Lock settings – Verify or delete values
Access the time lock menu and access the function. LCD will display
the message:
Press
and then
Press
, LCD will display the set values for the first day.
Press
to scroll all the set values.
Press
to delete the set values. LCD will display the message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
, LCD will display the message:
ver. 1.0 2012 11 13
11 of 16
WEEKLY TIME LOCK
SETTINGS
VERIFY OR
DELETE VALUES
hh:mm
FRI
hh:mm
DELETE?
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
v
Press
to confirm or press
At the end of the list press
to exit.
END OF LIST
.
Closing periods settings - Add new values
Access the time lock menu and access the function. LCD will display
the message:
CLOSING PERIODS
SETTINGS
Press
, LCD will display the message:
ADD NEW VALUES
Press
, LCD will display the message:
DD/MM/YY hh:mm
DD/MM/YY hh:mm
Enter first closing time and date and then opening time and date. Press
to confirm.
If a value for the year is set, this closing period will cease after that date. If a value for the year is
not set, the closing period will repeat every year.
To cancel entered values, press
.
Repeat this procedure for every closing period.
During closing periods the safe’s door can not be opened.
Up to 30 opening periods are available for a maximum of fourteen (14) days each.
Closing periods settings – Verify or delete values
Access the time lock menu and access the function. LCD will display
the message:
Press
and then
Press
, LCD will display the first saved closing period.
Press
to scroll all the set values.
Press
to delete the set values. LCD will display the message:
Press
to delete the LCD values or press
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
, LCD will display the message:
CLOSING PERIODS
SETTINGS
VERIFY OR
DELETE VALUES
DD/MM/YY hh:mm
DD/MM/YY hh:mm
DELETE?
v
to exit.
ver. 1.0 2012 11 19
12 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
At the end of list press
END OF LIST
.
Opening periods settings- Add new values
Access the time lock menu and access the function. LCD will display
the message:
OPENING PERIODS
SETTINGS
Press
. LCD will display the message:
ADD NEW VALUES
Press
. LCD will display the message:
DD/MM/YY hh:mm
DD/MM/YY hh:mm
Enter first opening time and date and then closing time and date. Press
to confirm.
If a value for the year is set, this opening period will cease after that date. If a value for the year is
not set, this opening period will repeat every year.
To cancel entered values, press
.
Repeat this procedure for every opening period.
During opening periods it will be possible to open the safe’s door even if time lock is active.
Up to 30 opening periods are available for a maximum of fourteen (14) days each.
Opening periods settings - Verify or delete values
Access the time lock menu and access the function. LCD will display
the message:
OPENING PERIODS
SETTINGS
Press
and then
VERIFY OR DELETE
VALUES
Press
, LCD will display the first saved opening period.
Press
to scroll all the set values.
Press
to delete the set values. LCD will display the message:
Press
to delete the LCD values or press
At the end of list press
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
, LCD will display the message:
DD/MM/YY hh:mm
DD/MM/YY hh:mm
DELETE?
v
to exit.
END OF LIST
.
ver. 1.0 2012 11 13
13 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Audit
Download the audit on a Dallas key
Use this function to download all keypad and lock events on a Dallas key.
Access the Master menu and access the function. LCD will display
the message:
Enter the audit Dallas key into the reader. If the operation is
successfully performed LCD will display the message:
ENTER DALLAS
…
OPERATION DONE
Slide events on the LCD
Use this function to check all the opening and closing events stored in the lock.
Access the Master menu and access the function. LCD will display
the message:
ENTER DALLAS
Press
SLIDE EVENTS
ON LCD
or wait. LCD will display the message:
LCD will start showing all the opening and closing events stored on
the lock.
Press
to slide all the events or
…
001: 28/09
WED
14:42:48
to exit.
Change Master code
Access the Master menu and access the function. LCD will display
the message:
CHANGE MASTER
CODE
Press
ENTER NEW CODE
XXXXXXXX
and enter the new code.
CONFIRM CODE
XXXXXXXX
Confirm the new code.
Always perform this operation with the door open.
Manager Management
Access the Master menu and access the function. LCD will display
the message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 19
14 of 16
MANAGER
MANAGEMENT
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Press
. LCD will display the message:
MANAGER
v
“V”: Manager installed, “_”: Manager deleted, “X”: Manager disabled.
Press
. If the Manager is not installed LCD will display the
message:
Press
to confirm or press
to confirm.
01
INSTALL?
to disable/enable/delete and press
Dynamic codes
Use this function to enable/disable dynamic codes function on the lock. Dynamic codes function
can be only enabled when lock is open. Open the lock before enable the function.
Access the Master menu and access the function. LCD will display
the message:
DYNAMIC CODES
Press
. LCD will display the message:
DYNAMIC CODES
DISABLED (ENABLED)
Press
. LCD will display the message:
DYNAMIC CODES
ENABLE? (DISABLE?)
Press
to confirm. LCD will display the message:
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
15 of 16
OPERATION DONE
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Before operating the lock,
please read this manual thoroughly,
and retain it for future reference.
Correct disposal of this product:
(Waste Electrical & Electronic Equipment)
Applicable in the European Union and other European countries
with separate collection systems.
This marking displayed on the product or its literature indicates that
it should not be disposed with other wastes at the end of its working
life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
M-LOCKS BV
Vlijtstraat 40
NL-7005 BN Doetinchem
ver. 1.0 2012 11 13
16 of 16
Tel: +31 (0)314 376 876
Fax: +31 (0)314 376 878
www.m-locks.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising