The Bowflex Revolution®XP Home Gym Assembly

The Bowflex Revolution®XP Home Gym Assembly
The Bowflex Revolution®XP
Home Gym
Assembly Instructions
P/N: 001-7057 Rev $ (/0)
2
Table of Contents
Before You Start ....................................... 2
Tools You Will Need / Hardware Contents.... 3
Box Contents............................................ 6
Assembling Your Bowflex Revolution ..........10
Important Contact Numbers ......................29
Before You Start
Before You Assemble
Select where you are going to locate your Bowflex Revolution®XP carefully. The best place for your
Bowflex Revolution®XP is on a hard, level surface. For best results, assemble your the unit in the
location where you intend to use it. Allow a workout area of at least 7’ length x 7’ width (2.1m L x 2.1m
W) of free space for safe operation of the Bowflex Revolution®XP.
Basic Assembly Principles
Here are a few basic tips that will make your assembly of the Bowflex Revolution®XP quick and easy.
By using these principles, you can simplify each process and save yourself extra time and effort.
1. To make the assembly process go faster, gather the pieces you need for each step and thoroughly
read the assembly instructions for that step prior to starting assembly for the step.
2. When tightening a locknut on a bolt, use a combination wrench to grip the locknut and ensure that
it is fastened securely.
3. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt
through the holes.
4. As a general rule, and for all bolts and nuts on your Bowflex Revolution®XP, turn bolts or nuts
toward the right to tighten and left to loosen. Or you can remember the mnemonic: “Righty tighty,
lefty loosey.”
3
Tools You Will Need
Hex Wrenches Are Provided in the Box
These Tools Are Not Provided in the Box
Phillips Head Screwdriver
3/32” Allen Wrench for #8 Allen Screws
3/4” and 9/16” Wrenches or Adjustable Wrenches
5/16” Allen Wrench for 1/2” Allen Screws
7/32” Allen Wrench for 3/8” Allen Screws
1/8” Allen Wrench for Top Cover Screws
* Tool and Hardware specifications subject to change
without notice.
3/16” Allen Wrench for Upholstery Screws
Hardware
9
12
2
8
7
10
11
1
3
4
13
6
5
Hardware Card (Box 2)
ITEM NO.
QTY.
DESCRIPTION
1
2
BUTTON HEAD CAP SCREW WITH THREADLOCK 3/8”X3/4”
2
2
NYLOCK NUT 1/2”
3
1
WRENCH, ALLEN HEX 3/32”
4
1
WRENCH, ALLEN HEX 1/8”
5
1
WRENCH, ALLEN 7/32”
6
1
WRENCH, ALLEN HEX 5/16”
7
2
WASHER 3/8”
8
4
WASHER 1/2”
9
5
SPRING CLIP
10
4
1/2” PLASTIC PLUG
11
4
3/8” PLASTIC PLUG
12
2
BUTTON HEAD CAP SCREW 1/2”x3 1/4”
13
1
WRENCH, HEX 3/16”
4
Hardware
12
7
10
9
2
5
2
6
6
Only two needed for XP model.
Use 4 for FT model.
3
8
3
4
2
1
11
Used on the FT model only
Hardware Card (Box 3)
ITEM NO.
QTY.
DESCRIPTION
1
6
BUTTON HEAD CAP SCREW 3/8”x 2 3/4”
2
16
NARROW WASHER 3/8”
3
7
NYLOCK NUT 3/8”
4
2
BUTTON HEAD CAP SCREW WITH THREADLOCK 3/8”x 3/4”
5
5
BUTTON HEAD CAP SCREW WITH THREADLOCK 1/2”x 1”
6
9
NARROW WASHER 1/2”
7
1
BUTTON HEAD CAP SCREW 3/8”x 4”
8
2
NYLOCK NUT 1/2”
9
1
BUTTON HEAD CAP SCREW 1/2”x 4 1/2”
10
2
RUBBER PAD
11
4
CABLE HOOK
12
1
BUTTON HEAD CAP SCREW 1/2”x 4”
5
Hardware
9
8
6
5
2
3
7
4
1
Hardware Card (Box 4)
ITEM NO.
QTY.
DESCRIPTION
1
6
BUTTON HEAD CAP SCREW 3/8”x 4”
2
8
NARROW WASHER 5/16”
3
18
NARROW WASHER 3/8”
4
6
NYLOCK NUT 3/8”
5
8
BUTTON HEAD CAP SCREW WITH THREADLOCK 5/16”x 1”
6
1
SEAT BOTTOM LOCK PIN
7
6
BUTTON HEAD CAP SCREW WITH THREADLOCK 3/8”x 3/4”
8
1
LEG EXTENSION PIN
9
4
END CAP
6
Box Contents
BOX 1
1
3
2
2
6
5
4
Box 1 Contents
ITEM
QTY.
DESCRIPTION
1
1
PRE STRETCH HARDWARE PACK
2
4
20LB PACK ASSEMBLY
3
2
40LB PACK ASSEMBLY
4
2
PRE-STRETCH PACK ASSEMBLY
5
2
5LB PACK ASSEMBLY
6
2
10LB PACK ASSEMBLY
7
Box Contents
BOX 2
8
10
9
7
Box 2 Contents
ITEM NO.
QTY.
DESCRIPTION
7
1
REVOLUTION MAIN UNIT
8
1
BOX HARDWARE CARD
9
2
FOOT CAP
10
1
REAR STABILIZER
8
Box Contents
BOX 3
12
16
21
17
11
15
18
13
19
14
20
Box 3 Contents
ITEM NO.
QTY.
DESCRIPTION
11
1
SHAFT
12
1
BOWFLEX HANDLE KIT
13
1
PLATFORM
14
1
LEFT STABILIZER
15
1
RIGHT STABILIZER
16
4
PULLEY
17
1
SQUAT HARNESS
18
1
MULTI POINT FOOT HARNESS
19
1
TRANSPORT WHEELS
20
2
LEG EXT CABLES
21
1
BOX 3 HARDWARE CARD
9
Box Contents
BOX 4
33
32
29
24
30
34
35
26
28
31
25
22
23
27
Box 4 Contents
ITEM NO.
QTY.
DESCRIPTION
22
1
SEAT TUBE
23
1
LOWER SEAT CONNECTOR
24
1
HARDWARE CARD BOX 4
25
1
LEG EXT ASSEMBLY
26
4
FOAM ROLLER PAD
27
2
ROLLER TUBE
28
1
SEAT TUBE CAP
29
1
DOCUMENTS KIT
30
1
BACK PAD
31
1
BACK PAD BRACKET
32
1
SEAT PAD BRACKET
33
1
SEAT PAD
34
1
RIGHT SEAT SUPPORT PLATE
35
1
LEFT SEAT SUPPORT PLATE
10
Assembly (Unboxing)
WA R N I N G
Warning: The Bowflex Revolution®XP Home Gym is very heavy. Whenever possible use
two people to unbox the main unit.
We have designed the packaging to make unboxing the main unit as safe and easy as
possible.
NOTE: Some of the hardware needed for unboxing is located on the Box 3 Hardware Card
Top layer of
styrofoam
Open top flaps
Step 1
1-1 Open the top flaps of Box 2
(Figure A) and split the
corners along the perforations
to expose the top layer of
styrofoam. (Figure B)
Split box corners
along perforations
Figure B
Figure A
Step 2
Rear Stabilizer Hardware
Rear Stabilizer
Top layer of
styrofoam
2-1 Remove the Rear Stabilizer,
and Hardware Pack, (Figure C)
then remove the top layer of
styrofoam to expose the lower
portion of the Main Frame.
(Figure D)
Lower portion of
Main Frame
The two Foot Caps that are
packaged in this box will be installed
in Step 6. (Figure E)
Figure C
Foot Caps
Figure E
Figure D
11
Assembly (Unboxing)
Transport Wheel
Transport Wheel
Plate
Step 3 Assemble Rear Stabilizer
Transport Wheel
Plate
Parts:
• Rear Stabilizer (Box 2)
• Rubber Pads (Box 3 hardware card)
• Transport Wheels (Box 3)
Holes
Tools:
• 7/32” Allen Wrench
3-1 Insert Transport Wheels into Rear Stabilizer
making sure that the holes in the Stabilizer
and the plates on the Transport Wheels are
pointing up.
Rear Stabilizer
3-2 Install and completely tighten the hardware.
Rubber Pad
3-3 Press the Rubber Pads into the holes on the opposite
side of the hardware.
Hardware (1:1):
2 Button Head Cap Screw With Threadlock (3/8” X 3/4 ”)
2 Washer (3/8”)
12
Assembly (Unboxing)
Step 4 Install Rear Stabilizer
Parts:
• Rear Stabilizer (From Step 3)
Tools:
• 5/16” Allen Wrench
• 7/32” Allen Wrench
• 3/4” Wrench or Adjustable Wrench
4-1 Place the Rear Stabilizer in the bracket on the Main Frame with
the wheels pointing away from the frame. Make sure the two bolt
holes in the Rear Stabilizer are pointing downward.
4-2 Install but do not tighten two 3/8”x3/4” Allen Bolts and 3/8”
washers (Box 3 Hardware Card) in the underside of the Rear Stabilizer.
4-3 Install two 1/2”x3 1/4” Allen Bolts with 1/2” washers and Nylock Nuts
in the sides of the Rear Stabilizer.
4-4 Completely tighten all of the hardware.
Rear Stabilizer
Threaded bolt holes
point downward
Wheels point
away from frame
1/2” Washer
1/2”x 3 1/4” Allen Bolt
1/2” Nylock Nut
1/2” Washer
Main Frame
3/8” Washer
3/8”x 3/4” Allen Bolt
Bracket
Hardware (1:1):
2 Button Head Cap Screw With Threadlock (3/8” X 3/4”)
2 Button Head Cap Screw (1/2” X 3 1/4”)
4 Washer (1/2”)
2 Nylock Nut (1/2”)
2 Washer (3/8”)
13
Assembly (Unboxing)
Step 5 Install Stabilizers and Lower Lat Connector
Parts:
• Right and Left Stabilizer (Box 3)
• Lower Seat Connector (Box 4)
Tools:
• 5/16” Allen Wrench
• 3/4” Wrench or Adjustable Wrench
5-1 Insert Lower Seat Connector into the Main Frame with the
threaded hole on the flat side pointing down as shown.
5-2 Align the Right and Left Stabilizers with the holes in the Main frame.
5-3 Install but DO NOT TIGHTEN the hardware.
NOTE: You will install an additional screw in the Lower Seat Connector when the unit is upright.
1/2”x 1” Allen Bolt
Main Frame
1/2” Washer
Left Stabilizer
1/2” x 4 1/2” Allen Bolt
Lower Seat Connector
Make sure threaded
hole is pointing down.
1/2” Nylock Nut
Hardware (1:1):
Right Stabilizer
4 Button Head Cap Screw With Threadlock (1/2” X 1”)
1 Button Head Cap Screw (1/2” X 4 1/2 ”)
6 Washer (1/2”)
1 Nylock Nut (1/2”)
14
Assembly (Unboxing)
Step 6
3/8 x 2 3/4 ” Button Head
Cap Screw
Parts:
• Platform (Box 3)
• Foot Caps (Box 2)
Tools:
• 7/32” Allen Wrench
• 9/16” Wrench or Adjustable Wrench
3/8” Washer
6-1 Align Platform with Stabilizers making
sure the rubber pads are pointing
downward.
3/8” Nylock Nut
6-2 Install DO NOT TIGHTEN the hardware.
3/8” Washer
6-3 Install Foot Caps onto the ends of the Stabilizers.
Hardware (1:1):
6 Button Head Cap Screw (3/8” X 2 3/4”)
12 Washer (3/8”)
6 Nylock Nut (3/8”)
Step 7
With the help of a partner, slowly roll the box completely over so the unit rests on the
Rear Stabilizer and Platform.
15
Assembly (Unboxing)
Step 8
8-1 Lift the box up and off of the styrofoam packing.
8-2 Separate the styrofoam packing. Remove plastic
wrapping from the engine.
Separate styrofoam
packing
Lift box
Styrofoam packing
Step 9
Tools:
• 5/16” Allen Wrench
9-1 Install one 1/2”x3/4” Allen Bolt.
1/2”x 1” Allen Bolt
9-2 Make sure Platform is flat and level and
completely tighten hardware from steps 5
through 9.
1/2” Washer
Hardware (1:1):
1 Button Head Cap Screw With Threadlock (1/2” X 1 ”)
1 Washer (1/2”)
16
Assembly
Step 10 Remove Top Cover
Top Cover
Remove screws
Tools:
• 1/8” Allen wrench
10-1 Use a 1/8” Allen Wrench to remove the four
screws in the Top Cover, then remove
the Top Cover and set it aside. Set screws
aside for Step 16.
Remove front piece first
Step 11 Remove Styrofoam Inner Packing
11-1 Remove and discard the three pieces of
Styrofoam Inner Packing.
Note: You must open the plastic bag
and remove each piece of styrofoam
individually.
Styrofoam Packing
17
Assembly
Main unit
Step 12 Install Tension Shaft
Parts:
• Main Unit
• Shaft (Box 3)
12-1 Align the rounded side of the
Tension Shaft with the rounded
side of the hole in the Main Unit
and slowly slide the Shaft through
until it clicks into place.
Rounded edge on top
Shaft
If the Shaft is obstructed
inside the Main Unit,
loosen the tension
screws in the Tension
Shaft Holder (see Step 13).
Note: If you didn’t feel or hear a distinct click, make sure the shaft is centered by measuring the
amount of exposed shaft on each side of the Main Unit. There should be an equal measure
on each side.
18
Assembly
Step 13 Tighten Tension Shaft Holder
Tools:
• 7/32” Allen Wrench
13-1 Use a 7/32” Allen Wrench to tighten the Tension Shaft Holder by
tightening the screws in numerical order shown on the tensioner.
Tighten the two screws marked 1, then the two marked 2, etc.
Note: Do not replace Top Cover at this time.
Tension screws
Tighten screws in order
1&1 , 2&2, 3&3, then
4&4.
Tension Shaft Holder
19
Assembly
Side view of pre-tension
SpiraFlex ® pack
Step 14 Install Pre-Tension SpiraFlex® Packs.
Tools:
• 3/32” Allen Wrench (Box 1)
Pre-tension
Hooks toward
SpiraFlex®Pack
main unit
#8-32 X 3/8” Allen screw
Parts:
• Pre-tension SpiraFlex® Packs (Box 1)
14-1 Align the rounded edge of the Pre-tension
SpiraFlex® Pack with the rounded edge of
the Tension Shaft and slide it all the way
onto the shaft.
Cam
14-2 When the Pack makes contact with
the Cam, continue to apply pressure
and twist the Pack to the left until
you feel the Pack seat into place.
14-3 Install and completely tighten
hardware, installing screws in a star
pattern around pre-tension pack.
Hardware (1:1):
Hardware for this step located in Box 1
12 Allen Bolt ( # 8-32 X 3/8”)
Remove Cam Holders
Step 15 Remove Cam Holders.
Tools:
• Phillips Head Screwdriver
15-1 Use a Phillips Head Screwdriver
to remove the Cam Holders.
Note: The Cam Holders are only
needed when the Spiraflex®
packs are not installed and
may be discarded or recycled.
Cam Holders
Allen Bolt
20
Assembly
Step 16 Replace Top Cover
Make sure inside edges
of Shroud fit in slots
on Top Cover
Parts:
• Top Cover
Allen Screw
Top Cover
Rear
Slots
Front
Inside Edge
Tools:
• 1/8” Allen Wrench
Tab
Shroud
16-1 If the screws are still in the Top Cover
from Step 1, remove them to avoid
dropping them into the Main Unit.
16-2 Replace the Top Cover front end first.
Make sure inside edge of the Shroud
fits into the slots in the Top Cover.
Now seat the rear making sure the
tabs on the Top Cover fit inside the
Shroud.
16-3 Install and completely tighten the hardware.
!4 4 % . 4 ) / .
Before Installing the Seat Support Plates (Step 17), make sure the Cables are properly tensioned
according to the following procedure . If there is slack in the Cables, the Support Plate Bolts
could cause interference.
Adjusting Cable Tension
Pay close attention to maintenance of the cable tension. Over time and with heavy use, the
cables are designed to give slightly. Located on the main engine housing is a tension control
knob which allows you to increase the tension in the cables.
Checking for incorrect cable tension is simple.
1. Position the adjustable swing arms in the upper most position.
2. Check to see if clips at end of cable hang down or if they are tight against the pulley.
3. If cables don’t have enough tension, use the tension control knob on the side of the machine to
tighten the cables. (See image).
4. To increase tension, pull tension knob outward and turn the large pulley clockwise. The clip on
the cable should be touching the pulley.
21
Assembly
Adjusting Cable Tension (continued)
There are tension knobs on each side of the machine. To increase
cable tension, pull knob and turn the large pulley clockwise. You’ll
know when you have enough tension when the cable retracts and
the cable clip touches the pulley.
The cable clip
should stop here.
Large pulley. This is what you
need to turn to increase the
tension on the cable. Pull the
tension knob and use your
other hand to turn the large
pulley clockwise.
In this image, the cable clip extends a few
inches below the pulley, so there is not enough
tension in the cable. The cable clip should be
tight against the pulley with appropriate tension.
3/8”x 4” Button Head Cap
Screw
Step 17 Install Seat Support Plates
Right Lat Support Plate
Parts:
• Right and Left Lat Support Plate (Box 4)
3/8” Nylock Nut
Tools:
• 7/32” Allen Wrench
3/8” Narrow Washer
17-1 Orient the Lat Support Plates so the hooks
on the plates are on the outside and align
the Left and Right Lat Support Plates with
the holes on the Main unit.
Hook
Left Lat Support Plate
3/8” Narrow Washer
17-2 Install BUT DO NOT TIGHTEN the hardware.
Hardware (1:1):
2 Button Head Cap Screw (3/8” X 4”)
4 Narrow Washer (3/8”)
2 Nylock Nut (3/8”)
22
Assembly
Step 18 Install Seat Tube
3/8”x 4” Button Head Cap
Screw
Seat Support Tube
Parts:
• Seat Tube (Box 4)
3/8” Nylock Nut
Tools:
• 7/32” Allen Wrench
3/8” Narrow Washer
18-1 Align the Seat Tube with the holes in the
Seat Support Plates and the Lower Seat
Connector.
18-2 Install and completely tighten the hardware
from step 17 and 18.
Hardware (1:1):
8 Narrow Washer (3/8”)
4 Button Head Cap Screw (3/8” X 4”)
Seat Tube Cap
Step 19 Seat Tube Cap
3/8”x 3/4” Button Head
Cap Screw
If you ordered the Lat Attachment,
do not install the Seat Tube Cap.
Refer to the Lat Attachment Assembly Manual
3/8” Narrow Washer
Parts:
• Seat Tube Cap (Box 4)
Seat Tube
Tools:
• 7/32” Allen Wrench
19-1 Insert the Seat Tube Cap into the top of the
Seat Tube.
19-2 Install and completely tighten the hardware.
Hardware (1:1):
6 Button Head Cap Screw With Threadlock (3/8” X 3/4”)
4 Nylock Nut (3/8”)
6 Narrow Washer (3/8”)
23
Assembly
Step 20 Install Cable Hooks
Parts:
• Rope Hooks (Box 3 Hardware Card)
Tools:
• 5/16” Allen Wrench
20-1 Align the Hooks with the holes in the
Main Frame with the tabs on the hooks
inserted into the slots in the Main Frame.
20-2 Install and completely tighten the hardware.
1/2” Nylock nut
NOTE: The remaining holes in the
Main Frame just above the
Hook Holes should be plugged
with two 1/2” plugs from the
Box 2 hardware card.
The remaining plugs are
not needed on this unit and
can be discarded.
Hook
Main Frame
Plug these holes
1/2”x 4” Button Head
Cap Screw
Hook
Hardware (1:1):
1 Button Head Cap Screw (1/2” X 4 ”)
Plug
1 Nylock Nut (1/2”)
24
Assembly
Pulley
Step 21 Install Pulleys
Hook Bolt
Spring
Parts:
• Pulley Components (Box 3)
Spring Cap
Hook Bolt
Tools:
• Screwdriver
Spring Cap
Hex Nut (discard)
NOTE: Remove and discard the hex nut to
disassemble the Pulley components.
21-1 Place a Spring Cap over a threaded hole in a
Stabilizer and screw the Hook Bolt into the
hole ONLY about three turns. (Figure A)
21-2 Place the Spring down over the Hook Bolt.
Compress the Spring and hook the Eyelet
under the Pulley to the Hook Bolt. (Figure B)
Figure A
21-3 Place a screwdriver through the Spring and
Hook Bolt on the Pulleys and tightly screw
them into the Stabilizers. (Figure C)
Screwdriver
NOTE: Place the pulleys with the
pre-installed cable closest to the main frame.
Pulley
Hook Bolt
Eyelet
Spring
Figure C
Figure B
25
Assembly
Step 22 Install Back Pad
Seat Back
Parts:
• Back Pad (Box 4)
• Back Pad Bracket (Box 4)
Seat Back Bracket
5/16” Washer
Tools:
• 3/16” Allen Wrench
22-1 Align the Back Pad with the lower 4 holes
in the Back Pad Bracket. The upper holes
are not used with this pad.
22-2 Install and completely tighten the hardware.
Hardware (1:1):
5/16” Button Head
Cap Screw
4 Button Head Cap Screw (5/16” X 1”)
4 Washer (5/16”)
Step 23 Install Seat Pad
Seat Pad
Parts:
• Seat Pad (Box 4)
• Seat Pad Bracket (Box 4)
Smaller Notch
Tools:
• 3/16” Allen Wrench
23-1 Align the Seat Pad with the holes
in the Seat Pad Bracket. Make sure the
smaller notch in the Seat Pad is opposite the
hooks on the Bracket.
Seat Pad Bracket
23-2 Install and completely tighten the hardware.
5/16” Washer
Hardware (1:1):
4 Button Head Cap Screw (5/16” X 1”)
4 Washer (5/16”)
5/16” Button Head
Cap Screw
26
Assembly
Attaching Seat and Back Pad
Attach the Seat and Back Pad to the Main unit by placing the Upper Hooks
onto the respective Upper Post and rotating the Lower Hook into position.
Once the Seat Pad is in postion, insert the Locking Pin through the hole
behind the Lower Hook to secure the pad to the Seat Tube.
Upper Hook
Upper Post
Back Pad
Upper Hook
Seat Pad
Locking Pin
Upper Post
27
Assembly
Roller Pad
Step 24 Assemble Leg Extension
Parts:
• Foam Roller Pads Pad (Box 4)
• Roller Tubes (Box 4)
• Leg Extension Assembly (Box 4)
• End Caps (Box 4 Hardware Card)
• Leg Extension Pin (Box 4 Hardware Card)
Leg Extension Assembly
Leg Extension Pin
Roller Tube
24-1 Slide the Roller Tubes through the
holes in the Leg Extension Assembly
followed by the Roller Pads and End Caps.
24-1 Place the Leg Extension Pin through Leg Extension
Assembly and Pivot Tube.
Install the Leg Extension Assembly by pulling
down on the Pop-Pin under the Seat and inserting
the Leg Extension into the bracket. Slide the Leg
extension to the desired position and screw the
Pop-Pin tightly into place.
Leg Extension Assembly
Seat Pad
Pop-Pin
Pivot Tube
End Cap
28
Assembly
Step 25 Install Cables
Parts:
• Ropes (Box 3)
25-1 Remove the Ball End from the cable by
pressing the insert out of the ball (Figure A)
and slide the ball off of the cable.
25-2 Route the cable under the Pulley closest
to the Main Unit and reinstall the Ball End
(Figure B).
Cable
Pulley
Figure A
NOTE: When not in use, store the cable by wrapping it around
the Cable Hooks as shown.
Hooks
Figure B
29
Step 26 Apply Revolution XP Decal
Parts:
• Revolution® XP Decal (Box 4 Documentation Kit)
26-1 Apply the Decal to the Platform in the indented area as shown. .
Decal
Platform
30
Step 27 Final Inspection
Please inspect your machine to ensure that all fasteners are tight and components are
properly assembled. Review all warnings affixed to machine.
Congratulations! You have successfully completed assembly of your Bowflex
Revolution® XP home gym!
7! 2 . ) . '
Failure to visually check and test assembly
before use can cause damage to the Bowflex
Revolution® XP home gym and serious injury to
users and bystanders and can also compromise
the effectiveness of your exercise program.
Important Contact Numbers
If you need assistance, please have both the serial number of your machine and the date of
purchase available when you contact the appropriate Nautilus office listed below.
Please record the following information for future reference.
Serial Number
Date of Purchase
OFFICES IN THE UNITED STATES:
INTERNATIONAL:
E-mail: [email protected]
• TECHNICAL/CUSTOMER SERVICE
Nautilus, Inc.
World Headquarters
16400 SE Nautilus Drive
Vancouver, Washington, USA 98683
Phone: 800-NAUTILUS (800-628-8458)
Email: [email protected]
Fax: 877-686-6466
• CORPORATE HEADQUARTERS
Nautilus, Inc.
World Headquarters
16400 SE Nautilus Drive
Vancouver, Washington, USA 98683
Phone: 800-NAUTILUS (800-628-8458)
For technical assistance and a list of distributors in
your area, please call or fax one of the following
numbers.
• INTERNATIONAL CUSTOMER SERVICE
Nautilus International S.A.
Rue Jean Prouvé 6
1762 Givisiez / Switzerland
Tel: + 41-26-460-77-77
Fax: + 41-26-460-77-70
Email: [email protected]
BUSINESS OFFICES:
• SWITZERLAND OFFICE
Nautilus Switzerland S.A.
Tel: + 41-26-460-77-66
Fax: + 41-26-460-77-60
• GERMANY and AUSTRIA OFFICE
Nautilus GmbH
Tel: +49-2203-20-20-0
Fax: +49-2203-20-20-4545
• ITALY OFFICE
Nautilus Italy s.r.l.
Tel: +39-051-664-6201
Fax: +39-051-664-7461
• UNITED KINGDOM OFFICE
Nautilus UK Ltd.
Tel: +44-1908-267-345
Fax: +44-1908-267-346
• CHINA OFFICE
Nautilus Representative Office
Tel: +86-21-523-707-00
Fax: +86-21-523-707-09
31
This manual is written and designed
by industry professionals. If you
have any questions regarding your
Bowflex Revolution®XP Home Gym or
any instructions found in this manual,
please call 1-800-NAUTILUS
(800-628-8458) for assistance.
©200 Nautilus Inc. All rights reserved. 16400 S.E. Nautilus Drive, Vancouver, Washington, USA 98683.
Bowflex, Bowflex Revolution, and the Bowflex and Nautilus logos are either registered trademarks or trademarks of Nautilus, Inc.
All other trademarks are owned by their respective companies.
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement