EdgeStar DEP701EW Owner`s manual

EdgeStar DEP701EW Owner`s manual
Dehumidifier
Model: DEP701EW
Owner’s Manual
For more information on other great EdgeStar products on the web, go to http://www.edgestar.com
Important Safety Information
Improper handling can cause serious damage to the EdgeStar dehumidifier and/or to the user. This
dehumidifier is designed for domestic indoor use only. Do not use the unit for industrial or commercial use. Any
other use may invalidate the warranty. Please review the ratings label located on the rear panel of the unit for
electrical and other technical data related to this unit. The unit must be used in a properly grounded wall
outlet. Please read and follow the safety information listed below.
Electrical Safety
 This dehumidifier is designed for indoor use
only. Do not use the unit near bath tubs,
swimming pools or other bodies of water.
 Do not wet the housing or control panel.
 Do not exceed the power outlet ratings.
 Do not pull the unit by the cord.
 Always turn the unit off and unplug it from
the outlet when cleaning.
 Unplug the unit if it is not going to be used
for an extended time period.
 Do not operate the unit with a power plug
missing the ground plug, a damaged cord
or a loose socket.
 Be sure the dehumidifier is properly
grounded.
 Never plug or unplug the unit with wet
hands.
 Do not bypass, cut or remove the grounding
plug.
 Do not use extension cords or power strips
with this unit. You may need to contact your
electrician if it is necessary to use a longer
cord or do not have a grounded outlet. Do
not modify the power cord’s length or share
the outlet with other appliances. It is
recommended the unit be connected on its
own circuit.
 Do not start or stop the unit by switching the
circuit’s power on and off.
 If the power cord is damaged, it must be
replaced by the manufacturer or a
qualified technician.
 Never open the unit while it is plugged in.
 Immediately unplug the unit if it makes
strange sounds, emits smells or smoke
comes out of it, and contact customer
service.
 Do not remove any part of the casing unless
instructed by an authorized technician.
The water produced by the dehumidifier
 You should
never attempt to repair the unit
is not potable or suitable for drinking.
yourself.
Do not drink or use condensate or water
drained from the unit as it contains
contaminates and could make you sick.
i
General Safety
 This unit is not intended to be used by
children.
 Children should be supervised to ensure that
they do not play with this product.
 Do not allow children to play with the controls
or drop any objects into the air outlets or
vents.
 Care should be taken when using the unit in a
room with infants, elderly persons, and
children.
 Do not place flower vases, containers, or any
objects on top of the unit.
 Do not allow anyone to sit on the unit.
 Do not climb on or use the unit as a step.
 Do not cover the air intake or exhaust vents
with towels, clothes or materials that prevent
air flow.
 When using in closets or confined spaces, be
sure to keep doors open to allow proper
ventilation.
 Do not use this appliance near flammable gas
or combustibles, such as gasoline, benzene,
thinner, etc.
 Do not use in areas where chemicals are
handled.
 Do not place the unit near a heat source as
doing so may cause the plastic parts to melt.
 Only use in an upright position on a flat, level
surface and provide at least 10 inches of
clearance from any walls or objects.
 Route the power cord carefully to avoid
creating a tripping hazard.
 When using in closets or confined spaces, be
sure to keep doors open to allow proper
ventilation.
 Clean the filters every two weeks or as
needed.
 Inspect the filters regularly.
 Always insert the filters securely.
Electrical
should
not be disposed of
 Never
run theproducts
unit without
filters.
with household waste. Please contact your
local recycling center for more information on
how to recycle electronic waste.
Table of Contents
IMPORTANT SAFETY INFORMATION ................................................................. I
INTRODUCTION ................................................................................................... 1
PARTS IDENTIFICATION ..................................................................................... 2
BACK VIEW .......................................................................................................... 2
FRONT VIEW ......................................................................................................... 2
INSTALLATION INSTRUCTIONS ........................................................................ 3
CONTROL PANEL OVERVIEW............................................................................ 4
OPERATING THE CONTROL PANEL ................................................................. 5
POWER ................................................................................................................ 5
Auto-Restart: ................................................................................................ 5
Auto-Shut Off: .............................................................................................. 5
CONTINUOUS MODE ............................................................................................. 5
FAN SPEEDS .......................................................................................................... 5
SETTING THE HUMIDITY LEVEL ................................................................................... 5
LCD DISPLAY ....................................................................................................... 6
Error Codes .................................................................................................. 6
WATER FULL LIGHT ................................................................................................. 6
ADDITIONAL NOTES ABOUT THE DEHUMIDIFIER’S BEHAVIOR: ......................................... 6
DRAINING THE UNIT............................................................................................ 7
MANUAL DRAIN .................................................................................................... 7
CONTINUOUS DRAIN ............................................................................................. 7
MAINTENANCE .................................................................................................... 8
CLEANING THE UNIT ............................................................................................... 8
CLEANING THE PRE-FILTER ....................................................................................... 8
CLEANING THE WATER BUCKET ................................................................................ 8
PREPARATION FOR STORAGE .................................................................................. 9
ENERGY SAVING GUIDE..................................................................................... 9
TROUBLESHOOTING .......................................................................................... 9
SPECIFICATIONS ............................................................................................... 12
EdgeStar Portable Dehumidifier
ii
Introduction
Thank you for purchasing this EdgeStar portable dehumidifier. We are glad
you chose us. We believe that your purchase of this product opens a
relationship between you and EdgeStar. We will provide the customer
support needed to nurture that relationship.
This manual contains important information regarding the proper
installation, use and maintenance of your portable dehumidifier. Following
this manual will ensure that your product will work at its peak performance
and efficiency.
Your dehumidifier is designed to remove moisture in the air by
condensation removal and collecting the water in a removable bucket,
or draining into a drain hose that can be routed to a drain hole on the
floor or condensate pump.
Please save the original product packaging in case you need to safely
transport your portable dehumidifier.
For Your Records:
Please write down the model number and serial number
below for future reference. Both numbers are located
on the ratings label on the back of your unit and are
needed to obtain warranty service. You may also want
to staple your receipt to this manual as it is the proof of
your purchase, and is also needed for service under
your warranty.
Model Number:
Serial Number:
Date of Purchase:
To better serve you, please do the following before contacting customer
service:
1

If you received a damaged product, immediately contact the
dealer that sold you the product.

Read and follow this instruction manual carefully to help you install,
use and maintain your portable dehumidifier.

Read the troubleshooting section of this manual as it will help you
diagnose and solve common issues.

Register your product at http://www.edgestar.com and download
product guides, owner’s manuals, and access additional
troubleshooting resources.

If you need warranty service, our friendly customer service
representatives are available via email at [email protected]
or by telephone at 1 (866) 319-5473.
Parts Identification
Front View
Control Panel
Handle
Air Intake
Water Bucket
Water Level Indicator
Back View
Exhaust
Drain Plug
Power Plug
Casters
EdgeStar Portable Dehumidifier
2
Installation Instructions
Note:


Your dehumidifier will remove moisture from the air and collect the excess
water in a bucket. You can use the EdgeStar dehumidifier to create a
comfortable environment and prevent damage caused by moisture to
books or valuables in areas such as basements or home libraries. Follow
the instructions below to unpack and set up your unit.
Dehumidifiers
working in a
basement will have
little or no effect on
adjacent enclosed
rooms such as
closets, unless there
is enough
circulation of air in
and out of the
enclosed area.
The unit is designed
to work in
environments with
temperatures
between 41°F and
95°F
Caution:
The unit is designed to be used
indoors and freestanding, and
not be used outdoors, or be
built-in to a cabinet or used
under a counter.
1) Carefully unpack the dehumidifier from its box and packaging material,
and remove the adhesive tape holding the water bucket and filter in
place. You may want to save the box for storing and transporting the unit.
Let the unit sit upright for at least 24 hours before powering it on to allow
the compressor’s fluids to settle.
2) Place the dehumidifier on a level floor or surface that is strong enough
to support the unit with a full bucket of water in a room where the
ambient temperature will not drop below 41°F, and away from any heat
sources such as direct sunlight, heaters, radiators, dryers, etc.
Allow at least 10 inches of space all around the unit and at least 20 inches
of space above the unit.
If you have multiple power outlets in the room, choose one that is near the
dehumidifier and that will be able to provide adequate power to the unit.
See the power requirements listed on the product label printed on the
side, or on the back of your dehumidifier.
3) Close all windows and doors. To be most effective, use the dehumidifier
in a contained room. For example, use it in a room with four walls and a
ceiling, instead of a partitioned studio, or warehouse.
4) To activate the unit and ensure the warning switches are engaged,
remove the water bucket and reinstall it; otherwise, the unit may not work
properly.
5) Plug the unit in to a grounded outlet. (Read the Safety Information
section.)
6) When first using the unit, press the Power button on the top of the unit
and run it in continuous mode for 24 hours.
3
Control Panel Overview
Button
Function
The check filter feature is a reminder to clean the air filter for a
more efficient operation. The Filter light will illuminate after 250
hours of operation. To reset after cleaning the filter, press the Filter
button and the indicator light will shut off.
Sets the unit to run continuously until the water bucket is full. You
will not be able to use the increase/decrease humidity buttons.
Sets the fan speed from normal to turbo for your desired level of
moisture removal.
Powers the unit on or off.
Increases the desired relative humidity setting for damper air.
Note: The unit is not a
humidifier; using the increase
humidity button will not add
moisture to the air.
EdgeStar Portable Dehumidifier
Decreases the desired relative humidity setting for drier air.
Press to initiate the auto start and auto stop feature in conjunction
with the increase and decrease buttons.
Indicator Light
Function
Filter
Lights up to indicate the filter needs to be cleaned.
Full
The water full light will light up red if the unit has filled
the water bucket.
Cont.
Lights up when the unit is set to run continuously until
the water bucket is full.
On/Off
Lights up to indicate if the unit is in on or off position.
Turbo
Lights up to indicate the fan is on the high setting.
Normal
Lights up to indicate the fan is on the low setting.
Auto-Defrost
Lights up to indicate the auto defrost operation is on
LCD Display
Displays the level of humidity as well as error codes.
4
Operating the Control Panel
Power
Use the “Power” button to turn the portable dehumidifier on and off. By
default when you first use the power button, the unit will begin to operate
in normal fan speed mode.
Note: If the unit was powered off, wait at least 3 minutes before powering
it back on.
Auto-Restart: If power to the unit is interrupted, the dehumidifier will restart
itself in with the last used mode/settings once the power is restored. The
compressor will restart after 3 minutes.
Auto-Shut Off: The unit will shut off when the set humidity has been
reached, or when the water bucket is full, has been removed, or is not in
its proper position.
Continuous Mode
Continuous mode dehumidifies the air until the water bucket is full. Use the
continuous mode for maximum dehumidification. You will not be able to
use the set humidity buttons.
To operate the unit in continuous mode:
1) Make sure the power cord is plugged into a power outlet.
2) Press the “Power” button.
3) Press the “Cont.” button. The LED indicator next to “Cont.” will light up.
4) Select the fan speed by using the Normal or High button.
Fan Speeds
The dehumidifier has two fan speeds. Use the turbo fan speed for
maximum moisture removal. Use the normal fan speed for quieter
operation.
Select the fan speed by pressing the “Fan” button until desired mode is
illuminated
Setting the Humidity Level
Note: Relative Humidity (RH) is
the ratio of the actual water
content of the air at a given
temperature to the potential
water content at that same
temperature.
5
The desired humidity level can be set within a range of 35% Relative
Humidity (RH) to 80% RH in 5% increments.
To set the desired humidity level percentage:
1) Make sure the power cord is plugged into a power outlet.
2) Press the Power button. Make sure the “Cont.” light is turned off.
3) Press the “Increase” and “Decrease” buttons to set the desired humidity
level. After a few seconds, the LCD display will revert to the actual room
humidity level with ±5% accuracy. For drier air use the “Decrease” button.
Operating the Control Panel continued
LCD Display
The LCD Display will show the room’s relative humidity percentage by
default. Pressing the Increase and Decrease buttons will show the set
humidity for a few seconds, and then revert to the room’s relative
humidity.
Error Codes
In addition to showing the humidity, the display may show the following
error codes:
AS – Humidity sensor error
Power the unit off, and then unplug the unit for 15 minutes. Plug in and
power on. If the issue persists, please contact customer service.
ES – Temperature sensor error
Power the unit off, and then unplug the unit for 15 minutes. Plug in and
power on. If the issue persists, please contact customer service.
EC – Unit malfunction
Please make sure whether the ambient temperature is suitable for the
stated temperature in the manual or not. If not, please operate the unit
under the stated temperature. If the environment temperature is suitable
for the stated temperature, please contact customer service.
P2 – Bucket is full
Empty the water bucket and reinstall it.
Water Full Light
The Water Full Light will illuminate when the bucket is ready to be emptied.
The light also turns on when the bucket is not installed or installed
incorrectly. Once the water is drained, and the bucket is properly
installed, the unit will operate normally.
Additional notes about the dehumidifier’s behavior:



EdgeStar Portable Dehumidifier
Once the unit reaches the desired set humidity, the power button will
remain lit while the compressor and fan shuts off. You will not be able
to change the fan speed.
If the power to the unit was interrupted while the compressor was
running, the unit may take a few minutes to start the fan and
compressor.
If the room’s relative humidity is lower than the set humidity, the unit
will not start the fan and compressor unless you set the unit to run in
Continuous mode.
6
Draining the Unit
Manual Drain
The dehumidifier can be drained manually using the water bucket. When
the bucket is full, the unit will automatically stop running, and the water full
light will turn on.
Follow the steps to remove the bucket and dump the water.
1) Slowly and carefully pull the
bucket out by the handles until
you see the bucket handle.
2) Pull the bucket up by its
handle
Warning: The water produced by
the dehumidifier is not potable or
suitable for drinking.
Do not drink the water drained
from the unit as it contains
contaminates and could make
you sick.
Continuous Drain
3) Pour the water out. Do not place the bucket on the floor as its bottom is
uneven and will fall down.
4) Reinstall the bucket.
The dehumidifier can be drained continuously to a floor drain.
1) Remove the water bucket from the unit, and you will find a hose
connector. You can use a 12 mm hose to attach to the connector.
2) Remove the rubber plug from the back of the unit’s drain hose outlet,
and push the drain hose through.
3) Securely attach the drain hose to the connector. Lead the other end of
the hose to a floor drain or other suitable drainage port.
4) You must reinstall the water bucket.
7
Maintenance
Clean the dehumidifier and filters regularly to maintain performance and
efficiency, and prolong the unit’s life. Be sure to always unplug the
dehumidifier from the power outlet before cleaning.
Cleaning the unit
Use a soft dry cloth to wipe the body clean. If necessary, use lukewarm
water to dampen a cloth to clean the unit. Use a soft bristle brush and
vacuum cleaner to clean between the air intake and exhaust vents.
Never use abrasive chemicals, volatile substances, gasoline, detergents,
chemically treated cloths, or other cleaning solvents that may damage
the cabinet exterior.
Never spray water directly on the unit.
Cleaning the pre-filter
Clean the pre-filter periodically to prolong the unit’s life, and keep the unit
running efficiently. Lint, dust, and dirt can clog the unit and reduce its
performance and effectiveness. If the unit is used in a dusty environment
you may need to clean it on a weekly basis.
To clean the pre-filter, follow the steps below:
1) Power off the unit and remove the pre-filter.
NOTE: Do not put the filter in a
dishwasher.
2) Use a vacuum cleaner or tap the filter lightly to remove loose dust and
dirt, then rinse thoroughly under lukewarm running water (below 104°F).
You may use a mild soap and water solution if needed. Allow the pre-filter
to air dry in a cool and shaded place. Dry thoroughly before reinstalling.
3) Reinsert the pre-filter.
Warning: Never operate the unit without the air filter.
Cleaning the water bucket
NOTE: Do not put the water
bucket in a dishwasher.
EdgeStar Portable Dehumidifier
Wash the water bucket frequently to prevent the growth of bacteria,
mildew and mold.
To clean the water bucket, follow the steps below:
1) Remove the water bucket from the unit.
2) Wash the bucket with clean water and a mild detergent. Rinse the
bucket thoroughly.
3) Install the water bucket.
8
Maintenance continued
Preparation for Storage
If you are not going to be using the unit for an extended period of time,
follow the instructions below before storing your unit:
1) Turn off the unit and wait 24 hours before emptying the water tank.
2) Drain all the water from the water tank.
3) Clean the air filter, water tank and unit.
4) Unplug and carefully wind the power cord.
5) Cover the unit with a plastic bag.
6) Store the unit in an upright position in a dry, well-ventilated place.
Energy Saving Guide
Read and follow the guide below to get the best performance and
efficiency from your portable dehumidifier:
 Do not cover the air outlet (exhaust) while in use.
 Do not place the unit in front of curtains or drapes- to ensure they do
not obstruct the air intake.
 Keep curtains, blinds or drapes closed during the sunniest part of the
day.
 Close all windows and doors.
 Indoor relative humidity should ideally be kept between 35 and 60
percent depending on the ambient temperature.
 Make sure the unit is on a level surface.
 To prolong the compressor's life, please wait at least 3 minutes before
turning the unit back on after shutting it off.
 Inspect and keep the pre-filters clean by cleaning regularly.
 Perform routine maintenance.
9
Troubleshooting
Follow the troubleshooting chart to resolve common issues.
Issue
Possible Cause
Insufficient time to dry
Air intake or Exhaust
vents are blocked
My dehumidifier does
not dry the air
Humidity control may
not be set low enough
Opened windows or
doors
Room temperature is
too low (below 41ºF)
There is a kerosene
heater or something
giving off water vapor
in the room
Frost appears on the
coils
This is normal behavior
Unit is not receiving
power
Insufficient power
My dehumidifier is not
functioning at all
Water bucket is full
Water bucket is not in
proper position
Control panel is
disconnected
The unit is not level
My dehumidifier is
making a loud noise
A foreign object has
jammed the fan
The floor below the unit
is uneven
Air filter is clogged
My dehumidifier is
making a continuous
metallic knocking or
pinging sound
EdgeStar Portable Dehumidifier
Unit may have been
shipped on its side
Damaged compressor
Solution
Run the unit for a
longer period of time.
Make sure there are no
towels, curtains, or
furniture blocking the
front and back of the
unit.
Lower the humidity
control. Run the unit in
continuous mode.
Close all windows and
doors.
Increase the room
temperature.
Remove any device
producing water
vapor.
The dehumidifier has
an auto-defrost
feature.
Make sure the unit is
plugged in.
Move the unit to
another outlet. Check
your circuit breaker.
(Refer to the rating
label on the back of
the unit to determine
the Amperage draw).
Drain the unit and
restart.
Remove bucket and
reinsert.
If no indicator lights
turn on, contact
customer service.
Make sure the unit is on
a level surface.
Shut off the unit, and
remove the object
from the fan.
Move the unit to a
level surface.
Clean the air filter.
Shut off the unit. Let
the unit sit on a level
surface for at least 24
hours and restart.
Contact customer
service.
10
Troubleshooting continued…
My dehumidifier is
leaking
A drain hose has been
attached and is loose
Cracked water bucket
11
My dehumidifier runs
for a little while and
then it trips the power
cord or the circuit
breaker
The dehumidifier may
be plugged into an
outlet that can not
supply the correct
amount of current
The control panel lights
blink randomly
Unit may have a faulty
control panel
Unit has an AS error
Humidity sensor error
Unit has an ES error
Temperature sensor
error
Unit has a EC error
Unit malfunction
Unit has a P2 error
Bucket is full
Bucket is not correctly
installed
Secure the drain hose.
Route your drain hose
to a drain hole or
condensate pump.
Contact custom.er
service.
Contact an electrician
if the unit works in a
different room or
circuit.
Restart the unit, and if
issue persists, contact
customer service.
Restart the unit, and if
issue persists, contact
customer service.
Restart the unit, and if
issue persists, contact
customer service.
Make sure the ambient
temperature is suitable
for the unit (41°F –
95°F). If not please
operate the unit under
the stated
temperature.
If the ambient
temperature is suitable,
please contact
customer service.
Empty the bucket and
reinstall.
Remove the bucket
and reinstall.
Specifications
EdgeStar Portable Dehumidifier
Description of product
Portable Dehumidifier
Model
DEP701EW
Voltage/Frequency
AC 115V~60Hz
Power Consumption
720W
Operating Current
6.9A
Water Bucket Capacity
7.5 Liters / 1.98 Gallons
Dehumidifying Capacity @ 80F
RH60%
70 Pints/Day
Refrigerant
R410A
Dimensions
WxDxH
15 3/8” x 10 9/16” x 23 1/8”
Weight
40 lbs.
12
EdgeStar Limited Warranty
One (1) Year Parts & Ninety (90) Days Labor
This product is warranted by EdgeStar to be free from defective workmanship and materials, subject to any conditions
set forth as follows:
WHAT IS COVERED:
LABOR: For a period of NINETY (90) DAYS from the date of original purchase, labor will be performed free of charge at
an authorized EdgeStar repair facility. At its option, EdgeStar will repair the product with new or remanufactured parts,
or exchange the defective product with a new, refurbished, or remanufactured product. If a product is replaced, it will
carry the remaining warranty of the original product. After the ninety (90) day period, EdgeStar will no longer be
responsible for labor charges incurred. All defective products and parts covered by this warranty will be repaired or
replaced on a mail-in basis to an EdgeStar authorized repair facility.
PARTS: For a period of ONE (1) YEAR from the date of original purchase, EdgeStar will supply new, rebuilt, or
refurbished parts free of charge. EdgeStar may request a defective part be returned in exchange for the replacement
part. All replacement parts or products will be new, remanufactured, or refurbished. All products and parts replaced by
EdgeStar under warranty service become the property of EdgeStar.
This warranty applies to the original purchaser only, and only covers defects in workmanship experienced during
operation of the product under normal service, maintenance, and usage conditions. This warranty applies to the
purchase and use of this product in residential settings within the United States of America.
WHAT IS NOT COVERED:
The following limitations apply to the coverage of this warranty. This warranty does not cover:
x
Labor charges for installation, setup or training to use the product.
x
Shipping damage, and any damage caused by improper packaging for shipment to an authorized service center, and any
damaged caused by improper voltage or any other misuse, including abnormal service, handling, or usage.
x
Cosmetic damage such as scratches and dents.
x
Normal wear and tear on parts or replacement of parts designed to be replaced, e.g. filters, cartridges, batteries.
x
Service trips to deliver, pick-up, or repair, install the product, or to instruct in proper usage of the product.
x
Damages or operating problems resulting from misuse, abuse, operation outside environmental specifications, uses
contrary to instructions provided in the owner’s manual, accidents, acts of God, vermin, fire, flood, improper installation,
unauthorized service, maintenance negligence, unauthorized installation or modification, or commercial use.
x
Labor charges incurred 91 days or more after the date of original purchase.
x
The use of EdgeStar products in commercial settings.
x
Optional accessories, attachments, and appearance items.
x
Products that have been modified to perform outside of specifications without the prior written permission of EdgeStar.
x
Products lost in shipment, or theft.
x
Products sold AS IS or from an unauthorized reseller.
x
Products that have had their serial numbers removed or defaced. Products with serial numbers that have been invalidated.
OBTAINING WARRANTY SERVICE:
If you believe your product is defective, contact EdgeStar Customer Support for troubleshooting assistance and
warranty service at 1-866-319-5473. Please have your serial number and proof of purchase available. Once an
EdgeStar authorized representative has confirmed that your product is defective and eligible for warranty service, the
product must be returned to an EdgeStar repair facility. The purchaser is solely responsible for prepaying all shipping
related costs to and from the repair facility. EdgeStar is not responsible for damage resulting from shipper mishandling
or improper packaging. Do not return a defective product to the place of purchase. Products received without a return
authorization number will be refused.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER
THE MANUFACTURER NOR ITS DISTRIBUTORS SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR PROFITS,
OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. SOME STATES DO NOT ALLOW THE
EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO
STATE.
EdgeStar Beverage Cooler
10
EdgeStar Products
500 N. Capital of TX Hwy, Bldg 5
Austin, TX 78746
Toll Free: 1-866-319-5473
Web: http://www.edgestar.com
E-mail: [email protected]
Register your product, download owner’s manuals, access additional
troubleshooting resources, and obtain more information on other great
EdgeStar & Koldfront products on the web at: http://www.edgestar.com
Product contents and specifications may change without notice.
Copyright © 2012 Living Direct, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement