4S645 USER`S MANUAL
4S645
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-4S645R3A
Release date: July 2002
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT
USER’S NOTICE ............................................................................... ii
MANUAL REVISION INFORMATION............................................... 1
COOLING SOLUTIONS ................................................................... 1
CHAPTER 1 INTRODUCTION OF 4S645 MOTHERBOARD
1-1
1-2
1-3
1-4
FEATURE OF MOTHERBOARD............................................................... 2
SPECIFICATION .......................................................................................... 3
PERFORMANCE LIST ................................................................................ 4
LAYOUT DIAGRAM & JUMPER SETTING ........................................... 5
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS ..................................................... 7
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING .......................... 7
2-3 INSTALL CPU ............................................................................................... 8
2-3-1 GLOSSARY....................................................................................................8
2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU ........................................9
2-4 INSTALL MEMORY .................................................................................... 10
2-5 EXPANSION CARD ...................................................................................... 11
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION .................. 11
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD ............................................ 11
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD .......... 12
2-5-4 AGP SLOT ..................................................................................................... 12
2-6 CONNECTORS, HEADERS......................................................................... 12
2-6-1 CONNECTORS ............................................................................................. 12
2-6-2 HEADERS ...................................................................................................... 15
2-7 STARTING UP YOUR COMPUTER.......................................................... 19
CHAPTER 3 INTRODUCING BIOS
3-1
3-2
3-3
3-4
3-5
3-6
ENTERING SETUP....................................................................................... 20
GETTING HELP............................................................................................ 21
THE MAIN MENU ........................................................................................ 21
STANDARD CMOS FEATURES................................................................. 22
ADVANCED BIOS FEATURES .................................................................. 24
ADVANCED CHIPSET FEATURES .......................................................... 26
3-6-1 DRAM TIMING SETTINGS ............................................................ 27
3-6-2 AGP FUNCTION SETTINGS .......................................................... 28
3-7 INTEGRATED PERIPHERALS.................................................................. 28
3-7-1 ONCHIP IDE FUNCTION................................................................ 29
3-7-2 ONCHIP DEVICE FUNCTION ....................................................... 30
3-7-3 ONCHIP SUPERIO FUNCTION ..................................................... 31
3-8 POWER MANAGEMENT SETUP .............................................................. 32
3-8-1 PM WAKE UP EVENTS .................................................................. 33
3-9 PNP/PCI CONFIGURATION SETUP......................................................... 34
i
3-10
3-11
3-12
3-13
3-9-1 IRQ RESOURCES ............................................................................ 35
PC HEALTH STATUS ................................................................................. 35
MISCELLANEOUS CONTROL................................................................. 36
LOAD STANDARD/OPTIMIZED DEFAULTS ....................................... 37
SET SUPERVISOR/USER PASSWORD ................................................... 37
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 95/98/98SE/NT4.0/2000.............. 38
4-1 AGPVXD
INSTALL SIS AGPVXD DRIVER ........................................... 39
4-2 SOUND
INSTALL ALC201 AUDIO CODEC DRIVER .......................... 40
4-3 PC-HEALTH WINBOND HARDWARE DOCTOR MONITORING SOFTWARE 41
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM
OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 4S645 MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL
CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS
MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR
ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING
DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT
BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES,
AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE
OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.
ii
Manual Revision Information
Reversion
3.0
Revision History
Third Edition
Date
July 2002
Item Checklist
4S645 motherboard
Cable for IDE/Floppy
CD for motherboard utilities
□
Cable for USB Port 3/4 (Option)
4S645 User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal
management becomes increasingly crucial when building computer systems.
Maintaining the proper thermal environment is key to reliable, long-term system
operation. The overall goal in providing the proper thermal environment is keeping the
processor below its specified maximum case temperature. Heatsinks induce improved
processor heat dissipation through increased surface area and concentrated airflow
from attached fans. In addition, interface materials allow effective transfers of heat
from the processor to the heatsink. For optimum heat transfer, Intel recommends the
use of thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below
for collection of heatsinks evaluated and recommended by Intel for use with Intel
processors. Note, those heatsinks are recommended for maintaining the specified
Maximum T case requirement. In addition, this collection is not intended to be a
comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index
1
Chapter 1
Introduction of 4S645 Motherboard
1-1 Feature of motherboard
The 4S645 motherboard is design for use Intel Pentium 4 Processor in 478 Pin
Package/Northwood Processor with the SiS 645 Chipset delivers a high performance
and professional desktop platform solution. Which utilize the Socket 478 design and
the memory size expandable to 3.0GB.
This motherboard use the newest SiS 645 Chipset Supports 400MHz System Bus in
data transfer rate and 100MHz/133MHz/166MHz SDRAM clock frequency support
DDR200/DDR266/DDR333 DDR SDRAM Module . The 4S645 motherboard offers
ULTRA ATA 100 to provide speedier HDD throughout that boosts overall system
performance.
The motherboard also has an integrated AC’97 2.1 CODEC on board which is fully
compatible with Sound Blaster Pro that gives you the best sound quality and
compatibility.
For those wanting even greater graphic performance, an AGP 4X slot is included on the
board.
With USB control as well as capability of expanding to 4 USB function ports, the
4S645 meet future USB demand also this motherboard has built-in hardware monitor
function to monitor and protect your computer.
This motherboard can conditional support traditional ATX Power Supply, if the 12V
output of Power Supply can offer more than 120W, let you have more choice when
use Power Supply.
We use three phase design in CPU Vcore Voltage let CPU Voltage more stable when
CPU full speed running.
By Magic Install CD, users can install system drivers easily and friendly, and the
Magic BIOS Utility can offer BIOS live update from web, auto detected BIOS version
to prevent update wrong BIOS.
In 4S645, we have CPU Host clock step-by-step increment designs in BIOS Setup
Utility to increasing CPU Host Clock let users approach over clock demand.
4S645 provides high performance & meets future specification demand. It is really
wise choice for your computer.
2
1-2 Specification
Spec
Design
Chipset
CPU Socket
(mPGA478B Socket)
Memory Socket
Expansion Slot &
Headers
Integrate IDE
Audio
BIOS
Multi I/O
Description
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
∗
ATX form factor 4 layers PCB size: 30.5x21.0cm
SiS 645 North Bridge Chipset
SiS 961 HyperZip Media I/O Chipset
Support Intel Pentium 4 478 Pin package utilizes FlipChip Pin Grid Array (FC-PGA2) package processor
Support 1.5G∼2.2G 478 Pin Pentium 4 processor
Reserves support for future Intel Pentium 4 processors
184-pin DDR SDRAM module socket x3
Support 2 pcs DDR333 or 3 pcs DDR200/DDR266 DDR
SDRAM Modules
Expandable to 3.0GB
AGP slot x1 support AGP 2.0 & 4X mode
32-bit PCI slot x5
CNR slot x1
Two PCI IDE controllers support PCI Bus Mastering,
ATA PIO/DMA and the ULTRA DMA 33/66/100
functions that deliver the data transfer rate up to 100 MB/s
AC’97 Digital Audio controller integrated
AC’97 Audio CODEC on board
Audio driver and utility included
Award 2MB Flash ROM
PS/2 keyboard and PS/2 mouse connectors
Floppy disk drive connector x1
Parallel port x1
Serial port x2
USB connector x2
USB headers x2 (connecting cable option)
Audio connector (Line-in, Line-out , MIC & Game Port)
3
1-3 Performance List
The following performance data list is the testing result of some popular benchmark
testing programs. These data are just referred by users, and there is no responsibility
for different testing data values gotten by users (the different Hardware & Software
configuration will result in different benchmark testing results.)
Performance Test Report
Intel Pentium 4 1.9GHz mPGAB package
128M DDR266 x2 (SAMSUNG K4H280838B-TCB0)
256M DDR333 x1 (KINGMAX KDL684T4A2A-6)
VGA Expansion Card: NVDIA Geforce2 MX-400 64MB (1024x768xHi-color)
IBM DTLA-305040 (ATA-100)
Hard Disk Driver:
Award Optimal default
BIOS:
Win 98SE
OS:
CPU:
DRAM:
Performance Test Report
DDR266
5369
2492
103
9.76
42.5
52.7
45.1
DDR333
5477
2519
104
10.60
43.6
53.6
46.7
3D Mark 2000
3D Mark 2001
3D Winbench 2000
Final Reality
Content Creation Winstone 2000
Content Creation Winstone 2001
Business Winstone2001
Winbench 99:
CPU Mark 99
109
114
FPU Winmark 99
6600
6610
Business Disk Winmark99
7650
8980
Hi-end Disk Winmark99
19000
20400
Business Graphic Winmark
432
440
Hi-end Graphic Winmark
1250
1270
SYS Mark 2001 : SISMark 2000/2001 Rating (Internet Content Creation / Office
Productivity)
SISMark 2000
205 (223/192) 214 (233/201)
SISMark 2001
149 (167/133) 154 (174/136)
SISOFT Sandra 2001 :
Dhrystone ALU
MIPS
3623
3616
Whetstone FPU
MFLOPS
1136/2365
1131/2369
Int ALU/RAM
MB/S
881
1098
Float FPU/RAM
MB/S
892
1117
Integer SSE2
IT/S
7531
7538
Floating-Point SSE2
IT/S
9342
9333
QUAKE3 DEMO1
FPS
164.6
176.6
DEMO2
FPS
164.9
178.7
WCPUID System/CPU Clock
100.67/1912.81 100.67/1912.81
4
5
1-4 Layout Diagram & Jumper Setting
PRINT
GAME/MIDI PORT
PS/2 MOUSE
PS/2 Keyboard
USB
COM1
COM2
K/B Power ON
Jumper (JP1)
MIC
LINE-IN
LINE-OUT
CPU Socket
PS2 KB/Mouse Port
CPU FAN
USB Port
PC99 Back Panel
DDR DIMMX3
SiS 645 Chip
ATX 12V Power Conn.
ATX Power Connector
SYSTEM FAN
Front Panel Audio
AGP Slot
ITE 8705 Chip
CD Audio
SiS 961 Chip
2MBit Flash ROM BIOS
ATA 100 IDE Conn.
PCI Slot
Clear CMOS (JP2)
Floppy Connector
Front Panel Connector
CNR Slot
Wake On LAN
IR Connector
USB Port
6
Jumpers
Jumper
JP2
JP1
Name
Description
CMOS RAM Clear
Page
3-pin Block
P.7
Keyboard Power On Enable/Disabled 3-pin Block
P.8
Connectors
Connector
Name
Description
Page
ATX1
ATX2
KBMS1
ATX Power Connector
20-pin Block
P.12
ATX 12V Power Connector
4-pin Block
P.13
PS/2 Mouse & PS/2 Keyboard
Connector
6-pin Female
P.13
USB1
PRINT1
USB Port Connector
4-pin Connector
P.13
Parallel Port Connector
25-pin Female
P.13
AUDI_GAME
Audio/Game Connector
3 phone jack + 15-pin Connector
P.13
9-pin Connector
P.14
34-pin Block
P.14
40-pin Block
P.14
COM1/COM2 Serial Port COM1/2 Connector
FDC1
Floppy Driver Connector
IDE1/IDE2
Primary/Secondary IDE Connector
Headers
Header
Name
Description
Page
FAUDIO
USB2
HDLED
RESET
SPK2
ACPILED
PWRBT
WOL1
SPEAKER, MIC header
9-pin Block
P.15
USB Port Headers
9-pin Block
P.16
IDE activity LED
2-pin Block
P.16
Reset switch lead
2-pin Block
P.16
PC Speaker connector
4-pin Block
P.16
Power LED
2-pin Block
P.16
Power switch
2-pin Block
P.16
Wake On-LAN Headers
3-pin Block
P.17
SYSTEM FAN, CPU FAN
FAN Speed Headers
3-pin Block
P.17
IR1
CDIN1
IR infrared module Headers
5-pin Block
P.17
CD Audio-In Headers
4-pin Block
P.18
Expansion Sockets
Socket/Slot
Name
Description
Page
ZIF Socket 478
DIMM1, DIMM2, DIMM3
CPU Socket
478-pin mPGAB CPU Socket
P.9
SDRAM Module
Socket
184-pin DDR SDRAM Module
Expansion Socket
P.10
PCI1 ∼ PCI5
AGP
CNR
PCI Slot
32-bit PCI Local Bus Expansion slots P.11
AGP 4X Mode Slot
AGP Expansion Slot
CNR Slot
Communication Network Riser Slot
7
P.12
Chapter 2
Hardware installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JP2
A battery must be used to retain the motherboard configuration in CMOS RAM short 2-3
pins of JP2 to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JP2 and short pins 1-2 for a few seconds
4. Return JP2 to its normal setting by shorting pins 2-3
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
1
1
3
JP2
3
JP2
1-2 closed
Clear CMOS
2-3 closed
CMOS RAM Clear Setting
8
Normal (Default)
(2) Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password to power on system.
1
1
3
JP1
1-2 closed
(Default)
3
JP1
K/B Power ON Disable
2-3 closed
K/B Power ON Enabled
Keyboard Power On Setting
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces between
the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for
sound cards and modems; runs at approx. 8MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
9
Processor - the "central processing unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"
Front Side Bus Frequency - the working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache - the flash memory inside the CPU, normal it depend on CPU type
2-3-2 About Intel Pentium 4 478-pin CPU
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to
prevent overheating. If this is not the case, then purchase a correct cooling FAN before
you turn on your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF
socket and open it by first pulling the level sideways away from the socket then
upward to a 90-degree angle. Insert the CPU with the correct orientation as shown
below. The notched corner should point toward the end of the level. Because the
CPU has a corner pin for two of the four corners, the CPU will only fit in the
orientation as shown.
mPGA478B
Colden Arrow
CPU ZIF mPGAB Socket
When you put the CPU into the ZIF socket. No force require to insert of the CPU,
then press the level to Locate position slightly without any extra force.
10
2-4 Install Memory
This motherboard provides three 184-pin DUAL INLINE MEMORY MODULES
(DIMM) sites for DDR memory expansion available from minimum memory size of
64MB to maximum memory size of 3.0GB DDR SDRAM.
Valid Memory Configurations
Bank
184-Pin DIMM
Total Memory
Bank 0, 1 (DIMM1)
DDR200/DDR266/DDR333
DDR SDRAM Module
X1
64MB∼1.0GB
Bank 2, 3 (DIMM2)
DDR200/DDR266/DDR333
DDR SDRAM Module
X1
64MB∼1.0GB
Bank 4, 5 (DIMM3)
DDR200/DDR266 DDR SDRAM Module
X1
64MB∼1.0GB
3
64MB∼3.0GB
Total
System Memory (Max. 3.0GB)
NOTE! Due to SiS 645 chip specification limited it only can support 2 pcs DDR333
module when DDR clock setting in 166MHz.
DIMM3 (BANK4+BANK5)
DIMM2 (BANK2+BANK3)
DIMM1 (BANK0+BANK1)
Generally, installing DDR SDRAM modules to your motherboard is very easy, you
can refer to figure 2-4 to see what a 184-Pin DDR SDRAM module looks like.
Figure 2-4
NOTE!
When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its
indention on both sides.
WARNING! For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266compliant DDR Modules. When this motherboard operate at 133Mhz, most
system will not even boot if non-compliant modules are used because of the
strict timing issues, if your DDR Modules are not DDR266-compliant, set
the SDRAM clock to 100MHz to ensure system stability.
11
2-5 Expansion Cards
WARNING!
Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary
hardware or software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively
assign to one use. In a standard design, there are 16 IRQs available but most of them
are already in use.
Standard Interrupt Assignments
IRQ
0
1
2
3*
4*
5*
6*
7*
8
9*
10 *
11 *
12 *
13
14 *
15 *
Priority
N/A
N/A
N/A
8
9
6
11
7
N/A
10
3
2
4
N/A
5
1
Standard function
System Timer
Keyboard Controller
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
Sound Card (sometimes LPT2)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when enabled
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
12
Interrupt request are shared as shown the table below:
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Onboard USB 1
Onboard USB 2
AC97/MC97
PROMISE
INT A INT B INT C INT D INT E
√
√
√
√
INT F
INT G INT H
√
√
√
√
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support
“Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will
arise between the two PCI groups that will make the system unstable or
cards inoperable.
2-5-4 AGP Slot
This motherboard provides an AGP Slot, support the 1X/2X/4X AGP VGA card.
2x notch
4x notch
AGP SLOT
2-6 Connectors, Headers
2-6-1 Connectors
(1)
Power Connector (20-pin block) : ATX1
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.
13
Pin 1
PIN
ROW2
ROW1
1
2
3
4
5
6
7
8
9
10
3.3V
-12V
GND
Soft Power On
GND
GND
GND
-5V
+5V
+5V
3.3V
3.3V
GND
5V
GND
5V
GND
Power OK
+5V (for Soft Logic)
+12V
(2) ATX 12V Power Connector (4-pin block) : ATX2
This is a new defined 4-pin connector that usually comes with ATX Power Supply. The
ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 12V voltage to maintain system power consumption.
Without this connector might cause system unstable because the power supply can not
provide sufficient current for system.
This Motherboard Conditional supports the ATX
Power Supply which without Extra ATX 12V Power
connector, if it’s 12V output can offer more than
120W to maintain system power consumption.
GND
+12V
∗
GND
+12V
Pin 1
(3)
PS/2 Mouse & PS/2 Keyboard Connector: KBMS1
The connectors for PS/2 keyboard and PS/2 Mouse.
(4)
USB Port connector: USB1
The connectors are 4-pin connector that connect USB devices to the system board.
(5)
Parallel Port Connector (25-pin female): PRINT1
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The Onboard Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(6)
Audio and Game Connector : AUDIO_GAME (SPK1, LININ1, MIC1, GAME1)
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin
D-Subminiature Receptacle Connector for joystick/MIDI Device.
Audio output to speaker
Line-out :
Audio input to sound chip
Line-in :
Microphone Connector
MIC :
Game/MIDI : For joystick or MIDI Device
14
(7)
Serial Port COM1, COM2 : COM1, COM2
COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial port
can be disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED
PERIPHERALS SETUP” section for more detail information.
PS/2
MOUSE
PRINT
PS/2 USB
Keyboard
(8)
COM1
GAME/MIDI PORT
COM2
MIC
LINE-IN
LINE-OUT
Floppy drive Connector (34-pin block): FDC1
This connector supports the provided floppy drive ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to the floppy drives.
Pin 1
Floppy Drive Connector
(9)
Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s).
If you install two hard disks, you must configure the second drive to Slave mode by
setting its jumpers accordingly. Please refer to the documentation of your hard disk for
the jumper settings.
15
Pin 1
Primary IDE Connector
(10) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two
hard disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Pin 1
Secondary IDE Connector
•
Two hard disks can be connected to each connector. The first HDD is referred to as the
“Master” and the second HDD is referred to as the “Slave”.
•
For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM
drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.
2-6-2 Headers
(1)
Line-Out/MIC Header for Front Panel (9-pin): FAUDIO
This header connect to Front Panel Line-out, MIC connector with cable.
Without install the cable, this header default setting is 5-6 short, 9-10 short. When you
install the cable you have take off these jumpers.
16
AUD_RET_L
AUD_GND
AUD_VCC
AUD_RET_R
FAUDIO
2
10
Pin 1
AUD_MIC
AUD_MIC_BIAS
AUD_FPOUT_R
HP_ON
AUD_FPOUT_L
9
Line-Out, MIC Headers
-DATA
+DATA
GND
OC
-DATA
+DATA
GND
USB2
VCC
USB Port Headers (9-pin) : USB2
These headers are used for connecting the additional USB port plug. By attaching an
option USB cable, your can be provided with two additional USB plugs affixed to the
back panel.
VCC
(2)
OC (Over Current)
Pin 1
USB Port Headers
(3)
(4)
(5)
(6)
(7)
IDE Activity LED: HDLED
This connector connects to the hard disk activity indicator light on the case.
Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the lift of the system’s power supply. See the figure
below.
Speaker connector: SPK2
This 4-pin connector connects to the case-mounted speaker. See the figure below.
Power LED: ACPILED
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.
Power switch: PWRBT
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.
17
PWRBT
ACPILED
FP1
VCC5
ACPILED
PWRBTN
GND
SPK2
RESET
VCC5
HDDLED
GND
RSTSW
NC
Pin 1
HDLED
SPKR
NC
GND
VCC5
Pin 1
System Case Connections
(8)
Wake On-LAN Headers (3-pin) : WOL1
This connector connects to a LAN card with a WAKE ON-LAN output. This
connector power up the system when a wake up signal is received through the
LAN/Modem card.
5VSB
GND
WON
NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
WOL1
1
3
Wake-On-LAN Headers
(9)
FAN Speed Headers (3-pin) : SYSTEM FAN, CPU FAN
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the
fan manufacturer, the wire and plug may be different. The red wire should be positive,
while the black should be ground. Connect the fan’s plug to the board taking into
consideration the polarity of connector.
18
CPU FAN
1
3
1
SYSTEM FAN
3
(10) IR infrared module Headers (5-pin) : IR1
This connector supports the optional wireless transmitting and receiving infrared
module. You must configure the setting through the BIOS setup to use the IR function.
GND
IRRX
IR1
2
6
Pin 1
NC
VCC5
IRTX
5
IR infrared module Headers
(11) CD Audio-In Headers (4-pin) : CDIN1
CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.
CDIN1
1
4
CD Audio-In Headers
19
2-7 Starting Up Your Computer
1. After all connection are made, close your computer case cover.
2. Be sure all the switch are off, and check that the power supply input voltage is set to
proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.
3. Connect the power supply cord into the power supply located on the back of your system
case according to your system user’s manual.
4. Turn on your peripheral as following order:
a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply
and press the ATX power switch on the front side of the case.
5. The power LED on the front panel of the system case will light. The LED on the monitor
may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.
If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.
Beep
Meaning
One short beep when displaying logo
No error during POST
Long beeps in an endless loop
No DRAM install or detected
One long beep followed by three short beeps
Video card not found or video card memory bad
High frequency beeps when system is
working
CPU overheated
System running at a lower frequency
6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in
BIOS SETUP.
7. Power off your computer: You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click “Start” button, click “Shut down” and then click “Shut down the computer?”
The power supply should turn off after windows shut down.
20
Chapter 3
Introducing BIOS
The BIOS is a program located on a Flash Memory on the motherboard. This program
is a bridge between motherboard and operating system. When you start the computer,
the BIOS program gain control. The BIOS first operates an auto-diagnostic test called
POST (power on self test) for all the necessary hardware, it detects the entire hardware
device and configures the parameters of the hardware synchronization. Only when
these tasks are completed done it gives up control of the computer to operating system
(OS). Since the BIOS is the only channel for hardware and software to communicate,
it is the key factor for system stability, and in ensuring that your system performance
as its best.
In the BIOS Setup main menu of Figure 3-1, you can see several options. We will
explain these options step by step in the following pages of this chapter, but let us first
see a short description of the function keys you may use here:
•
Press <Esc> to quit the BIOS Setup.
•
Press ↑ ↓ ← → (up, down, left, right) to choose, in the main menu, the option you
want to confirm or to modify.
•
Press <F10> when you have completed the setup of BIOS parameters to save these
parameters and to exit the BIOS Setup menu.
•
Press Page Up/Page Down or +/– keys when you want to modify the BIOS
parameters for the active option.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup, restart
the system to try again by turning it OFF then ON or pressing the “RESET” button on
the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and
<Delete> keys. If you do not press the keys at the correct time and the system does
not boot, an error message will be displayed and you will again be asked to
Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup
21
3-2 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of
the screen.
Status Page Setup Menu/Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and
the possible selections for the highlighted item. To exit the Help Window, press
<Esc>.
3-3 The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will
appear on the screen. The Main Menu allows you to select from fourteen setup
functions and two exit choices. Use arrow keys to select among the items and press
<Enter> to accept or enter the sub-menu.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Standard CMOS Features
Miscellaneous Control
Advanced BIOS Features
Load optimized Defaults
Advanced Chipset Features
Load Standard Defaults
Integrated Peripherals
Set Supervisor Password
Power Management Setup
Set User Password
PnP/PCI Configurations
Save & Exit Setup
PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
↑↓→ ←
: Select Item
Time, Date, Hard Disk Type...
Figure 3-1
Standard CMOS Features
Use this Menu for basic system configurations.
Advanced BIOS Features
Use this menu to set the Advanced Features available on your system.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your system’s
performance.
22
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP/PCI configurations
This entry appears if your system supports PnP/PCI.
PC Health Status
This entry shows your PC health status.
Miscellaneous Control
Use this menu to specify your settings for Miscellaneous control.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings for optimal
performances system operations.
Load Standard Defaults
Use this menu to load the BIOS default values for the minimal/stable performance
system operation.
Set Supervisor/User Password
Use this menu to set User and Supervisor Passwords.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
3-4 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories. Each
category includes no, one or more than one setup items. Use the arrow keys to
highlight the item and then use the <PgUp> or <PgDn> keys to select the value you
want in each item.
23
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Standard CMOS Features
>
>
>
>
Date (mm:dd:yy)
Time (hh:mm:ss)
Mon, Oct, 26 2001
16 : 48 : 35
IDE
IDE
IDE
IDE
Press
Press
Press
Press
Primary Master
Primary Slave
Secondary Master
Secondary Slave
Enter
Enter
Enter
Enter
None
None
None
None
Drive A
Drive B
1.44M, 3.25 in.
None
Video
Halt On
EGA/VGA
All,But Keyboard
Base Memory
Extended Memory
Total Memory
Item Help
Menu Level >
Change the day, month,
year and century
640K
56320K
57344K
↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F5:Previous Values
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
Date
The date format is <day><month><date><year>.
Day of the week, from Sun to Sat, determined by BIOS. Read-only.
Day
Month The month from Jan. through Dec.
Date The date from 1 to 31 can be keyed by numeric function keys.
Year The year depends on the year of the BIOS.
Time
The time format is <hour><minute><second>.
Primary Master/Primary Slave
Secondary Master/Secondary Slave
Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the
specifications of your drive must match with the drive table. The hard disk will not
work properly if you enter improper information for this category. If your hard disk
drive type is not matched or listed, you can use Manual to define your own drive type
manually.
If you select Manual, related information is asked to be entered to the following items.
Enter the information directly from the keyboard. This information should be
provided in the documentation from your hard disk vendor or the system manufacturer.
If the controller of HDD interface is SCSI, the selection shall be “None”.
If the controller of HDD interface is CD-ROM, the selection shall be “None”
Access Mode The settings are Auto Normal, Large, and LBA.
number of cylinders
Cylinder
number of heads
Head
write precomp
Precomp
Landing Zone landing zone
number of sectors
Sector
24
3-5 Advanced BIOS Features
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Advanced BIOS Features
Anti-Virus Protection
CPU L1 & L2 Cache
CPU L2 Cache ECC Checking
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
HDD S.M.A.R.T. Capability
Report No FDD For Windows
Video BIOS Shadow
↑↓→← Move Enter:Select
F5:Previous Values
Disabled
Enabled
Disabled
Enabled
Floppy
HDD-0
CDROM
Enabled
Disabled
Enabled
On
Fast
Disabled
6
250
Setup
Non-OS2
Disabled
Yes
Enabled
Item Help
Menu Level >
Allows you to choose
the VIRUS warning
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled
and someone attempt to
write data into this
area, BIOS will show a
warning message on
screen and alarm beep
Enabled copies Video
BIOS to shadow RAM
Improves performance
+/-/PU/PD:Value F10:Save ESC:Exit
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
Anti-Virus Protection
Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection.
If this function is enabled and someone attempt to write data into this area, BIOS will show a
warning message on screen and alarm beep.
Disabled (default) No warning message to appear when anything attempts to access the
boot sector or hard disk partition table.
Activates automatically when the system boots up causing a warning
Enabled
message to appear when anything attempts to access the boot sector
of hard disk partition table.
CPU L1 Cache
The default value is Enabled.
Enabled (default) Enable cache
Disable cache
Disabled
Note: The internal cache is built in the processor.
CPU L2 Cache
Choose Enabled or Disabled. This option enables the Level 2 cache memory.
Quick Power On Self Test
This category speeds up Power On Self Test (POST) after you power on the computer. If this
is set to Enabled. BIOS will shorten or skip some check items during POST.
Enabled (default) Enable quick POST
Normal POST
Disabled
25
First/Second/Third/ Boot Device, Boot Other Device
The BIOS attempts to load the operating system from the devices in the sequence selected in
these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAN
and Disabled.
Swap Floppy Drive
Switches the floppy disk drives between being designated as A and B. Default is Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K
type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.
Boot Up NumLock Status
The default value is On.
On (default) Keypad is numeric keys.
Keypad is arrow keys.
Off
Gate A20 Option
The A20 signal is controlled by keyboard controller or chipset hardware.
Normal
Fast (default) The A20 signal is controlled by port 92 or chipset specific method.
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the
typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.
Typematic Rate (Chars/Sec)
Sets the number of times a second to repeat a keystroke when you hold the key down. The
settings are: 6, 8, 10, 12, 15, 20, 24, and 30.
Typematic Delay (Msec)
Sets the delay time after the key is held down before is begins to repeat the keystroke. The
settings are 250, 500, 750, and 1000.
Security Option
This category allows you to limit access to the system and Setup, or just to Setup.
The system will not boot and access to Setup will be denied if the
System
correct password is not entered at the prompt.
Setup (default) The system will boot, but access to Setup will be denied if the correct
password is not entered prompt.
OS Select For DRAM > 64MB
Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2.
Set to OS/2 if using more than 64MB and running OS/2.
Report No FDD For Win 95
Whether report no FDD for Win 95 or not. The settings are: Yes, No.
26
3-6 Advanced Chipset Features
The Advanced Chipset Features Setup option is used to change the values of the chipset
registers. These registers control most of the system options in the computer.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Advanced Chipset Features
> DRAM Timing Settings
> AGP Function Settings
Prefetch Caching
Memory Hole at 15M-16M
↑↓→← Move Enter:Select
F5:Previous Values
Press Enter
Press Enter
Disabled
Disabled
Item Help
Menu Level >
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
DRAM Timing Settings
Please refer to section 3-6-1
AGP Function Settings
This option determines the effective size of the graphics aperture used in the particular PAC
configuration. The AGP aperture is memory-mapped, while graphics data structure can
reside in a graphics aperture. The aperture range should be programmed as not cacheable in
the processor cache, accesses with the aperture range are forwarded to the main memory, then
PAC will translate the original issued address via a translation table that is maintained on the
main memory. The option allows the selection of an aperture size of 32MB, 64MB.
Please refer to section 3-6-2
Memory Hole at 15M-16M
You can reserve this area of system memory for ISA adapter ROM. When this area is
reserved, it cannot be cached. The user information of peripherals that need to use this area of
system memory usually discusses their memory requirements. The settings are: Enabled and
Disabled.
27
3-6-1 DRAM Timing Setting
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
DRAM Timing Setting
Auto Configuration
RAS Active Time
RAS Precharge Time
RAS to CAS Delay
Write Recovery Time
CAS Latency Setting
Standard
7T
2T
2T
2T
2.5T
Item Help
Menu Level >>
↑↓→← Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit
F5:Previous Values
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
RAS Active Time
Select the number of SCLKs for an access cycle. The settings are: Auto (Default), 6T, 7T, 5T,
4T.
RAS Precharge Time
If an insufficient number of cycles is allowed for the RAS to accumulate its charge before
DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast
gives faster performance; and Slow gives more stable performance. This field applies only
when synchronous DRAM is installed in the system. The settings are: Auto (default), 4T, 2T
and 3T.
RAS to CAS Delay
This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when
DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives
more stable performance. This field applies only when synchronous DRAM is installed in the
system. The settings are: 2T and 3T.
CAS Latency Setting
When synchronous DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing. The settings are: Auto (Default) 2T and 3T.
28
3-6-2 AGP Function Settings
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
AGP Function Settings
AGP
AGP
AGP
AGP
AGP
AGP
Transfer Mode
Fast Write
Aperture Size
Aperture Write Combining
Driving Control
Driving Value
↑↓→← Move Enter:Select
F5:Previous Values
Auto
Disabled
64MB
Enabled
Auto
88
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
3-7 Integrated Peripherals
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Integrated Peripherals
> OnChip IDE Function
> OnChip Device Function
> Onboard SuperIO Function
Power Loss Function
Init Display First
↑↓→← Move Enter:Select
F5:Previous Values
Press Enter
Press Enter
Press Enter
Always Off
PCI Slot
Item Help
Menu Level >
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
OnChip IDE Function
Please refer to section 3-7-1
OnChip Device Function
Please refer to section 3-7-2
Onboard SuperIO Function
Please refer to section 3-7-3
Init Display First
This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings
are: PCI Slot, AGP Slot.
29
3-7-1 OnChip IDE Function
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
OnChip IDE Function
Internal PCI/IDE
Primary Master
PIO
Primary Slave
PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master
UltraDMA
Primary Slave
UltraDMA
Secondary Master UltraDMA
Secondary Slave UltraDMA
IDE Burst Mode
IDE HDD Block Mode
Delay For HDD (Secs)
↑↓→← Move Enter:Select
F5:Previous Values
Both
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Enabled
Enabled
0
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
Internal PCI/IDE
The integrated peripheral controller contains an IDE interface with support for two IDE
channels. Select Both to activate each channel separately. The settings are: Both, IDE0,
IDE1.
Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of
the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide
successively increased performance. In Auto mode, the system automatically determines the
best mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode
4.
Primary/Secondary Master/Slave UltraDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the
operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus
master driver). If your hard drive and your system software both support Ultra DMA/33 and
Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If
your IDE hard drive supports block mode (most new drives do), select Enabled for automatic
detection of the optimal number of block read/writes per sector the drive can support. The
settings are: Enabled, Disabled.
30
3-7-2 OnChip Device Function
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
OnChip Device Function
AC97 Audio Device
Game Port Address
Midi Port Address
Midi Port IRQ
AC97 Modem Device
USB Controller
USB Keyboard Legacy Support
↑↓→← Move Enter:Select
F5:Previous Values
Enabled
201
Disabled
10
Enabled
Enabled
Disabled
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
AC97 Audio Device
This item allows you to decide to enable/disable the chipset family to support AC97 Audio.
The settings are: Enabled, Disabled.
Game Port Address/Midi Port Address
This will determine which Address the Game Port/Midi Port will use.
AC97 Modem Device
This item allows you to decide to enable/disable the chipset family to support AC97 Modem.
The settings are: Auto, Disabled.
USB Controller
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have
a USB peripherals. The settings are: Enabled, Disabled.
USB Keyboard Legacy Support
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have
a USB keyboard. The settings are: Enabled, Disabled.
31
3-7-3 Onboard SuperIO Function
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Onboard SuperIO Function
Onboard FDD Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART2 Mode
IR Duplex Mode
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
↑↓→← Move Enter:Select
F5:Previous Values
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
Half
378/IRQ7
SPP
3
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and
you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this
field. The settings are: Enabled and Disabled.
Onboard Serial Port 1/Port 2
Select an address and corresponding interrupt for the first and the second serial ports. The settings are:
3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.
UART 2 Mode
This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this functions
uses.
Onboard Parallel Port
There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP, and
EPP features. It has the following option:
Disabled
(3BCH/IRQ7)/ Line Printer port 0
Line Printer port 2
(278H/IRQ5)/
Line Printer port 1
(378H/IRQ7)
Parallel Port Mode
SPP
EPP
ECP
: Standard Parallel Port
: Enhanced Parallel Port
: Extended Capability Port
SPP/EPP/ECP/ECP+EPP
To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the
onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the
onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the
onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode
has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After
selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can
choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after
the user chooses the onboard parallel port with the EPP function, the following message will be
displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec.
can be chosen.
32
3-8 Power Management Setup
The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Power Management Setup
ACPI Function
ACPI Suspend Type
Video Off Option
Video Off Method
MODEM Use IRQ
Hot key Function as
Power Button Function
> PM Wake Up Events
↑↓→← Move Enter:Select
F5:Previous Values
Enabled
S1(POS)
Always Off
V/H SYNC+Blank
Auto
Power Off
Instant Off
Press Enter
Item Help
Menu Level >
+/-/PU/PD:Value F10:Save ESC:Exit
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
ACPI Function
This item allows you to Enabled/Disabled the Advanced Configuration and Power Management
(ACPI). The settings are Enabled and Disabled.
Video Off Option
This determines the manner in which the monitor is blanked. The choice are Suspend → off,
All Modes → Off, and Always On.
Video Off Method
This determines the manner in which the monitor is blanked.
Initial display power management signaling.
DPMS (default)
This option only writes blanks to the video buffer.
Blank Screen
V/H SYNC+Blank This selection will cause the system to turn off the vertical and
horizontal synchronization ports and write blanks to the video
buffer.
Modem Use IRQ
This determines the IRQ in which the MODEM can use.
The settings are: 3, 4, 5, 7, 9, 10, 11, NA.
Power Button Function
Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off
state. The settings are: Delay 4 Sec, Instant-Off.
PM Wake Up Events
Please refer to section 3-8-1
33
3-8-1 PM Wake Up Events
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PM Wake Up Events
IRQ [3-7,9-15],NMI
IRQ 8 Break Suspend
RING
Power Up Control
MACPME Power UP Control
KB Power ON Password
Power Up by Alarm
x Month Alarm
x Day of Month Alarm
x Time (hh:mm:ss) Alarm
↑↓→← Move Enter:Select
F5:Previous Values
Enabled
Disabled
Disabled
Disabled
Enter
Disabled
NA
NA
0 : 0 : 0
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
Ring Power Up Control
During Disabled, the system will ignore any incoming call from the modem. During Enabled,
the system will boot up if there’s an incoming call from the modem.
PCIPME Power Up Control
This will enable the system to wake up by PCI device Power Management function.
The settings are: Enabled and Disabled.
KB Power ON Password
This item can setting Power On Password, if you Enabled keyboard Power On function then
you can Power On system by key-in the password which you setting.
Power Up by Alarm
This function is for setting date and time for your computer to boot up. During Disabled, you
cannot use this function. During Enabled, choose the Date and Time Alarm:
Date(of month) Alarm
You can choose which month the system will boot up. Set to 0, to boot every day.
Time(hh:mm:ss) Alarm
You can choose what hour, minute and second the system will boot up.
Note: If you have change the setting, you must let the system boot up until it goes to the
operating system, before this function will work.
34
3-9 PnP/PCI Configuration Setup
This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the
CPU itself uses when communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only experienced users should
make any changes to the default settings.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
> IRQ Resources
PCI/VGA Palette Snoop
Assign IRQ For VGA
Assign IRQ For USB
↑↓→← Move Enter:Select
F5:Previous Values
Disabled
Manual
Press Enter
Disabled
Enabled
Enabled
Item Help
Menu Level >
Default is Disabled.
Select Enabled to
reset Extended System
Configuration Data
(ESCD) when you exit
Setup if you have
installed a new add-on
and the system
reconfiguration has
caused such a serious
conflict that the OS
cannot boot
+/-/PU/PD:Value F10:Save ESC:Exit
F6:Optimized Defaults
F1:General Help
F7:Standard Defaults
Reset Configuration Data
Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration
Data (ESCD) when you exit Setup if you have installed a new add-on and the system
reconfiguration has caused such a serious conflict that the operating system can not boot. The
settings are: Enabled and Disabled.
Resource Controlled By
The Award Plug and Play BIOS has the capacity to automatically configure all of the boot
and Plug and Play compatible devices. However, this capability means absolutely nothing
unless you are using a Plug and Play operating system such as Windows95/98. If you set
this field to “manual” choose specific resources by going into each of the sub menu that
follows this field (a sub menu is preceded by a “>”).
The settings are: Auto(ESCD), Manual.
IRQ Resources
When resources are controlled manually, assign each system interrupt a type, depending on
the type of device using the interrupt.
Please refer to section 3-9-1
PCI/VGA Palette Snoop
Leave this field at Disabled. The settings are Enabled, Disabled.
35
3-9-1 IRQ Resources
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
IRQ Resources
IRQ-3
IRQ-4
IRQ-5
IRQ-7
IRQ-9
IRQ-10
IRQ-11
IRQ-14
IRQ-15
assigned
assigned
assigned
assigned
assigned
assigned
assigned
assigned
assigned
to
to
to
to
to
to
to
to
to
↑↓→← Move Enter:Select
F5:Previous Values
PCI
PCI
PCI
PCI
PCI
PCI
PCI
PCI
PCI
Device
Device
Device
Device
Device
Device
Device
Device
Device
Item Help
Menu Level >>
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
3-10 PC Health Status
This section shows the Status of you CPU, Fan, Warning for overall system status. This is
only available if there is Hardware Monitor onboard.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PC Health Status
Shutdown Temperature
Show PC Health in Post
Vcore
VccVid
Vcc3
Vcc5
+12V
SB3V
-12V
SB5V
Vbat
CPU Temperature
System Temperature
CPU Fan
System Fan
↑↓→← Move Enter:Select
F5:Previous Values
Disabled
Enabled
1.5V
1.18V
3.3V
5.01V
12.02V
3.31V
-11.95V
5.02V
3.01V
43°C/109°C
33°C/91°C
5500 RPM
0 RPM
Item Help
Menu Level >
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
Show PC Health in Post
During Enabled, it displays information list below. The choice is either Enabled or Disabled
Current CPU Temperature/Current System Temp/Current CPUFAN, SYSFAN Speed/
Vcore/ Vcc/3.3V/+5V/+12V/-12V/5VSB(V)
This will show the CPU/FAN/System voltage chart and FAN Speed.
36
3-11 Miscellaneous Control
This section is for setting CPU Frequency Control.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Miscellaneous Control
CPU Clock Ratio
10 X
Auto Detect DIMM/PCI Clock
Enabled
Spread Spectrum
Disabled
Clock Control
By Hardware
** Current Host Clock is 100/33MHz **
HOST/PCI Clock at Next Boot is 100/33MHz
** Current DRAM Clock is 100 MHz **
DRAM Clock at Next Boot is
100MH (HOST CLK)
↑↓→← Move Enter:Select
F5:Previous Values
Item Help
Menu Level >
+/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F6:Optimized Defaults
F7:Standard Defaults
Auto Detect DIMM/PCI Clock
This item allows you to enable/disable auto detect DIMM/PCI Clock.
The settings are: Enabled, Disabled.
Clock Control
This item allows you to set the CPU Host Clock by Hardware (CPU/PCI 100/33MHz) or by
Software (BIOS)
Host/PCI clock at Next boot is
When Clock Control setting By Software this item allows you to set CPU Host Clock step by
step from 100MHz to 200MHz, use Page Down/Page Up key can change the frequency to
approach over clocking.
DRAM Clock at Next Boot is
This item allows you to set the DRAM clock synchronous as CPU Host Clock or
Asynchronous as Host clock 100MHz, 133MHz, 166MHz to approach your DDR SDRAM
specification.
37
3-12 Load Standard/Optimized Defaults
Load Standard Defaults
When you press <Enter> on this item, you get confirmation dialog box with a message similar
to:
Load Standard Defaults (Y/N)? N
Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system
operations.
Load Optimized Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:
Load Optimized Defaults (Y/N)? N
Pressing <Y> loads the default values that are factory settings for optimal performance
system operations.
3-13 Set Supervisor/User Password
You can set either supervisor or user password, or both of them. The differences are:
Supervisor password:
User password:
Can enter and change the options of the setup menus.
Can only enter but do not have the right to change the options of
the setup menus. When you select this function, the following
message will appear at the center of the screen to assist you in
creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>. The password typed
now will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to enter the password. A
message will confirm that the password will be disabled. Once the password is disabled, the
system will boot and you can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it every time you try to
enter Setup. This prevents an unauthorized person from changing any part of your system
configuration.
Additionally, when a password is enabled, you can also require the BIOS to request a
password every time your system is rebooted. This would prevent unauthorized use of your
computer.
You determine when the password is required within the BIOS Features Setup Menu and its
Security option. If the Security option is set to “System”, the password will be required both
at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter
Setup.
38
Chapter 4
DRIVER & FREE PROGRAM INSTALLATION
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all
DRIVERS you need and some free application programs and utility programs. In addition,
this CD also include an auto detect software which can tell you which hardware is installed,
and which DRIVERS needed so that your system can function properly. We call this auto
detect software MAGIC INSTALL.
MAGIC INSTALL Supports WINDOWS 95/98/98SE/ME/NT4.0/2000
Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below.
If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or
click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive).
From MAGIC INSTALL MENU you may make 8 selections:
1. AGPVXD
Install AGPVXD file when use External AGP card
2. SOUND
install ALC201 Audio Codec driver
3. PC-HEALTH
installs SMART GUARDIAN software for hardware monitoring device
4. MAGIC BIOS install BIOS Live Update Utility
5. DIRECTX8
install Microsoft DirectX 8.0 driver
6. PC-CILLIN
install PC-CILLIN2000 anti-virus program
7. BROWSE CD
to browse the contents of the CD
8. EXIT
to exit from MAGIC INSTALL menu
39
4-1 AGPVXD
Install SiS AGPVXD Driver
The AGPVXD Driver is Only For AGP Slot VGA CARD User, before install AGP card
driver please install this AGPVXD driver first.
The path of the file:
for WINDOWS 9X is X:\SIS645\AGPVXD\WIN9X\SETUP.EXE
(including WIN95/98/98SE/ME)
for WINDOWS 2000/XP is X:\SIS645\AGPVXD\WIN2K_XP\SETUP.EXE
For WINDOWS 95/98/98SE/ME/2000/XP
1. Click AGPVXD when Magic Install
MENU appears
2. Click Next when SiS Aceleration Graphic
Port appears
3. Click NEXT or choose BROWSE to
change the path For the file to be stored
4. After Setup complete please select restart
my computer now and click Finish to
complete setup
40
4-2 SOUND
Install ALC201 Audio Codec Driver
1. Click SOUND when MAGIC INSTALL
MENU appears
2. Then auto detect operation system language
edition, click Next, start to install DRIVER
3. Click Finish and Restart Windows
4. Click Start→Program→Avance Sound
Manager→AvRack. Then AVRACK Windows
appears
5. Avance Audio Rack table can play CD, WAV,
MID, MP3, AVI, MPG Format File
6. This is a Sound Environment Simulator and
Karaok function table
NOTE:
MAGIC INSTALL will auto detect file path:
41
X:\SIS645\SOUND\SETUP.EXE (for WINDOWS 95/98/98SE/ME/NT4.0/2000/XP)
4-3 PC-HEALTH installs SMART GUARDIAN software for
hardware monitoring device
1. Click PC-HEALTH when MAGIC INSTALL 2. Click Install when SMART GUARDIAN
MENU appears
INSTALL appears
3. Click OK after the software is installed
4. SMART GUARDIAN Utility
NOTE: MAGIC INSTALL will auto detect file path X:\SIS645\HEALTH\SETUP.EXE
This driver supports WINDOWS 95/98/98SE/NT4.0/2000
42
43
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising