Test Report - Lanches
Test Report
Applicant:
Guangdong East Power Co., Ltd.
Product:
Online High Frequency UPS
Trademark:
N/A
Model No:
EA66400, EA6620, EA6640, EA6660, EA6680, EA66100,
EA66120, EA66140, EA66160, EA66180, EA66200, EA66220,
EA66240, EA66260, EA66280, EA66300, EA66320, EA66340,
EA66360, EA66380.
Prepared by:
Most Technology Service Co., Limited
The safety testing has been performed on the submitted samples and found in compliance
with the council LVD directive 2006/95/EC.
Most Technology Service Co., Limited
No.5, 2nd Langshan Road, North District, Hi-tech Industry Park,
Nanshan, Shenzhen, Guangdong, China
Phone: 86-755-86026850
Fax: 86-755- 26013350
http:// www.szmost.com
Report No.: MTS/GEG/T13050257
Page 1 of 33
Test Report
EN 62040-1
Uninterruptible power systems (UPS) –
Part 1:General and safety requirements for UPS
Report
Reference No…………………………...: MTS/GEG/T13050257
Tested by (Name +signature) …………: Grace Gong
………………………………….
Approved by (Name +signature) ……..: Yvette Zhou
…………………………………..
Date of issue…………………………….: May 30, 2013
Testing laboratory
Name …………………………...……....: Most Technology Service Co., Limited
Address …………………...........…......: No.5, 2nd Langshan Road, North District, Hi-Tech Industrial park,
Nanshan, Shenzhen, Guangdong, China
Testing location ..................................: Same as above
Applicant
Name …………………………...……....: GUANGDONG EAST POWER CO., LTD.
Address ……………………………….. : NO.6 NORTHERN INDUSTRY ROAD, SONGSHAN LAKE SCI
&TECH INDUSTRY PARK, DONGGUAN, P.R. CHINA
Test specification
Standard ………………………………...: EN 62040-1: 2008
Procedure deviation …………………...: N/A
Non-standard test method …………….: N/A
Test item
Description ……………………………..: Online High Frequency UPS
Trademark ……………………………. : N/A
Model/type reference ……………….. : EA66400
Rating …………………………………. : Input: AC 380V, 50Hz, 545A
Output: AC 380V, 50Hz, 606A, 400KVA,/320KW
Manufacture Battery: DC±240V
Manufacturer …………………………. : GUANGDONG EAST POWER CO., LTD.
Address ……………………………….. : NO.6 NORTHERN INDUSTRY ROAD, SONGSHAN LAKE SCI
&TECH INDUSTRY PARK, DONGGUAN, P.R. CHINA
Report No.: MTS/GEG/T13050257
Page 2 of 33
Test item particulars
Operation condition …………………………..: Continuous
Tested IT power system …………………...…: N/A
IT testing, phase-phase voltage (V) ………...: N/A
Class of equipment ……………….……….…: Class I
Mass of equipment (kg) ..............................: Mention in user manual
Mains supply tolerance (%)………………..…: +6%, -10%
Protection against ingress of water …………: IP20
Possible test case verdicts:
- test case does not apply to the test object: N/A
- test object does meet the requirement:
P (Pass)
- test object does not meet the requirement: F (Fail)
General remarks
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see appended table)" refers to a table appended to the report.
“(see remark #)” refers to a remark appended to the report.
“(see Annex #) refers to an annex appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
General Product information:
All models are with same principle, constructional and insulation, just different of rating power, etc.
The test model EA66400 is the biggest power of all models.
Summary of Testing and Conclusions:
The Online High Frequency UPS was tested and complied with the requirements of EN 62040-1:2008.
Copy of marking plate:
Online High Frequency UPS
Model: EA66400
Input: AC 380V, 50Hz, 545A, 3
Output: AC 380V, 50Hz, 606A, 400KVA/320KW
Manufacture Battery: DC±240V
Date: March, 2013
Guangdong East Power Co., ltd.
MADE IN CHINA
Report No.: MTS/GEG/T13050257
Page 3 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
4
GENERAL CONDITIONS FOR TESTS
P
4.5
Components
P
Comply either with the requirements of this standard or All components comply with
with the safety aspects of the relevant IEC component the requirements of the
standard or with the safety
standard
aspects of the relevant IEC
component standards
See table 4.5 List of critical
components
Evaluation
and
testing
of
components
Components, Which are
1.5.2/RD
certified to IEC and/or national
standards, are applied correctly
within their ratings.
Components not covered by
IEC standards are tested under
the conditions present in the
equipment.
Thermal
controls
Thermal controls used are
1.5.3/RD
suitable for their intended
application and particularly
Annex K.
Transformers
Transformers used are suitable
1.5.4/RD
for their intended application
and comply with the relevant
requirements of the standard
and particularly Annex C
Interconnecting
cables
For external battery cabinet
1.5.5/RD
only
Capacitors
in
primary
circuits:
Between lines: X2 capacitor
1.5.6/RD
according to IEC 6038414:1993 with 21 days damp
heat test.
Between line/neutral and PE:
Y2 capacitor according to IEC
60384-14:1993.
Double
insulation
or
reinforced
insulation
bridged
by
See below.
1.5.7/RD
components
1.5.7.1/RD General
See below.
No bridging capacitors
1.5.7.2/RD Bridging capacitors
provided.
1.5.7.3/RD Bridging resistors
No such resistor
1.5.7.4/RD Accessible parts
1.5.8/RD
Components in equipment for IT power systems
4.6
Power interface
1.6.1/RD
AC power distribution systems
Report No.: MTS/GEG/T13050257
Backfeed protection in
compliance with requirements
of limited current circuits.
Further details see sub clause
2.4.
Not applied for IT power
systems.
P
P
P
P
P
P
P
P
N/A
N/A
P
N/A
P
TN power system.
P
Page 4 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
1.6.2/RD
1.6.4/RD
Input current
See table 4.6
P
Neutral conductor
Basic insulation for
rated voltage between earthed
parts and line and neutral
conductors.
O/p neutral is not isolated from
the i/p neutral.
P
4.7
Marking and instructions
4.7.1
General
4.7.2
Power rating
Verdict
P
P
All required markings are
affixed on labels located on the
front enclosure of UPS
Input rated voltage/range (V) ..................................... : See page 4
Input rated current/range (A)...................................... : See page 4
P
P
P
Input symbol for nature of supply (d.c.) ..................... : Not designed for "d.c. only".
Therefore, no such marking
required.
Input rated frequency/range (Hz) ............................... : See page 4
N/A
P
Output rated voltage/range (V) .................................. : See page 4
Output rated current/range (A) ................................... : See page 4
P
Number of output phases (1- 3) with/without neutral : UPS: 3with neutral
P
Output rated active power (W) ................................... :
P
P
See page 4
Output rated apparent power (VA) ............................. :
See page 4
Output symbol for nature of supply (d.c.) .................... : No d.c. output. Therefore, no
such marking required.
Rated frequency or rated frequency range (Hz)……….:
See page 4
Max. ambient operating temperature range (C)…….. : 0℃-40℃
Manufacturer’s name or trademark or
Guangdong East Power Co.,
identification mark ..................................................... : ltd.
Type/model or type reference .................................... :
See page 4
Symbol for Class II equipment only ........................... :
Class I equipment
Other symbols ........................................................... : Additional symbols or markings
do not give rise to
misunderstanding.
Certification marks .................................................... : CE
P
N/A
P
P
P
P
N/A
P
P
Instructions for units with automatic
See user manual
bypass/maintenance bypass, additional input
a.c. supply, or external batteries, having text
"See installation instructions before connecting
to the supply" ............................................................ :
P
4.7.3
Safety instructions
See below.
P
4.7.3.1
General
See below.
P
Report No.: MTS/GEG/T13050257
Page 5 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
Safety instructions available as required to avoid
introduction of hazards when operating, installing,
maintaining, transporting or storing the UPS.
User manual inform adequate
information to users and there
are such words in user manuals
4.7.3.2
Installation
4.7.3.3
Guidance on the level of competence necessary for
User manual inform adequate
installation for operator and service person ...............: information to users and there
are such words in user manuals
Installation instructions should include reference to
national wiring rules.
Operation
Guidance on the level of competence necessary to
operate the equipment.
4.7.3.4
Maintenance
4.7.3.5
Safety instructions to be used during maintenance of
the UPS are normally made available only to service
persons.
Distribution related backfeed
P
User manual inform adequate
information to users and there
are such words in user manuals
P
No mains voltage adjustment
device
Supply voltage adjustment .........................................: No adjustment.
Methods and means of adjustment; reference to
installation instructions ...............................................:
Power outlets .............................................................: The maximum apparent and
active power of the standard
outlet is indicated on the rating
plate.
Fuse identification (marking, special fusing
There is a marking located
characteristics, cross-reference) .................................: adjacent to each fuse to
indicate the specification of the
fuse
Wiring terminals
See below.
1.7.7.1/RD Protective earthing and bonding terminals ...................: The protective earthing wiring
terminal is indicated by the
symbol (IEC60417)
1.7.7.2/RD Terminal for a.c. mains supply conductors .................: Letter ’N’ used
Report No.: MTS/GEG/T13050257
P
P
1.7.4/RD
1.7.7.3/RD Terminals for d.c. mains supply conductors ……….....:
P
P
Main voltage adjustment ............................................:
4.7.7
1.7.7/RD
P
P
4.7.4
4.7.6
1.7.6/RD
P
P
For the purpose of warning the electrical service
person against backfeed situations not caused by the
UPS but that may arise when a particular load fault is
present while the UPS operates in stored energy mode
or while unbalanced loads are supplied through a
particular
power distribution system, the installation instructions
for permanently connected UPS shall require the fitting
of a warning label
Warning label with text "Before working on this circuit,
-Isolate Uninterruptible Power System (UPS)
-Then check for Hazardous Voltage between all
terminals including the protective earth.
Risk of Voltage Backfeed
4.7.5
1.7.5/RD
P
N/A
N/A
N/A
P
P
P
P
P
N/A
Page 6 of 33
EN 62040-1
Clause
Requirement – Test
4.7.8
4.7.9
1.7.8/RD
Battery terminals ........................................................: Internal batteries used
Controls and indicators
Result - Remark
Verdict
N/A
See below.
P
1.7.8.1/RD Identification, location and marking .............................: On battery bodys
1.7.8.2/RD Colours ..................................................................... : Colours are acceptable due to
only used for information (no
safety involved even if
disregarded).
Symbols
according
to
IEC
60417................................
:
1.7.8.3/RD
1.7.8.4/RD Markings using figures ............................................... :
4.7.10
Isolation of multiple power sources ............................ :
1.7.9/RD
IT power systems
4.7.11
1.7.10/RD
IT power distribution systems
4.7.12
Protection in building installations
4.7.13
5.1/RD
4.7.14
1.7.11/RD
4.7.15
1.7.12/RD
4.7.16
Durability of markings
Removable parts
The labels were subjected to
the permanence of marking
test. The labels were rubbed
with cloth soaked with water for
15 s and then again for 15 s
with the cloth soaked with
petroleum spirit.
After this test there was no
damage to the labels. The
marking on the labels did not
fade. There was neither curling
nor lifting of the label edges.
No removable part in normal
operation mode
4.7.18
1.7.13/RD
Replaceable batteries 
- if the battery is placed in an OPERATOR ACCESS
AREA, there shall be a marking close to the battery or a
statement in both the operating and the servicing
instructions;
- if the battery is placed elsewhere in the equipment,
there shall be a marking close to the battery or a
statement in the servicing instructions.
Report No.: MTS/GEG/T13050257
P
N/A
N/A
N/A
N/A
N/A
Permanerce connected
three-phase UPS, have the
protectin in buiding installations
and other protection.
High leakage current (mA) ............................. :
Leakage current of the
equipment does not exceed
3.5 mA.
Thermostats and other regulating devices
No device is intended to be
adjusted during in installation
or normal operation mode
Language(s) ............................................................. : English Language
1.7.11/RD
4.7.17
1.7.12/RD
Not used.
Only one external supply of
hazardous voltage or energy
Not applied for IT power
systems.
P
Replaceable by server person.
See user manual
P
N/A
N/A
P
P
N/A
P
N/A
P
Page 7 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
There is no operator access
with a tool in normal operation
mode
Battery
There is a battery warning label
in the battery compartment to
show the following information
--- battery type
--- nominal voltage of total
battery
--- nominal capacity of total
battery
--- warning label denoting an
energy or electrical shock and
chemical hazard and reference
See label in Annex Photos
Clearly legible information ......................................... : Warning label containing below
described information placed
on enclosure of UPS and
battery compartment.
Information clearly legible.
Battery type ................................................................: Lead acid, type as "12Vdc 7Ah"
4.7.19
Operator access with a tool................................... :
1.7.2.5/RD
4.7.20
Nominal voltage of total battery (V) ……………........:
N/A
P
P
P
DC±240V
Nominal capacity of total battery (optional) …………....: 7Ah
P
Warning label .............................................................:
P
P
Instructions ...............................................................:
P
4.7.21
Installation instructions
No special attention is needed
5
FUNDAMENTAL DESIGN REQUIREMENTS
P
5.1
Protection against electric shock and energy hazards
P
5.1.1
Protection for UPS intended to be used in operator
access areas
See below.
P
2.1.1.2/RD Battery compartments............................................. :
2.1.1.4/RD Access to hazardous voltage circuit wiring
2.1.1.5/RD Energy hazards ................................................ :
2.1.1.6/RD Manual controls
Permitted to have access to:
- bare parts of SELV circuits
- bare parts of limited current circuits
- TNV circuits under specified conditions
5.1.2
5.1.3
Protection for UPS intended to be used in service
access areas
Protection for UPS intended to be used in restricted
access areas
Report No.: MTS/GEG/T13050257
N/A
P
No any hazardous voltage
circuit wiring can be accessed
by operator.
There is no energy hazard in
operation access areas
No conductive controls or
handles or alike provided.
Operator access to earthing
metal enclosure only.
TNV circuits can’t accessed by
operation, test with probe
P
P
N/A
P
N/A
N/A
Page 8 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
Working voltage (Vpeak or Vrms); minimum
distance (mm) through insulation
5.1.4
Backfeed protection
See appended table 8.2.
-
Backfeed protection provided
Description of the construction ................................... :
by the mains relay.
P
5.1.5
Emergency switching device
P
5.2
Requirements for auxiliary circuits
P
5.2.1
Safety extra low voltage circuits – SELV
P
2.2.1/RD
General requirements
P
2.2.2/RD
Voltages under normal conditions
P
2.2.3/RD
Voltages under fault conditions
P
2.2.4/RD
Connection of SELV circuits to other circuits
Use isolate transformer and
adequate creepage distance and
clearance to provide reinforced
insulation between RS232 circuit
and hazardous voltage circuits
P
5.2.2
Telephone network voltage circuits – TNV
N/A
5.2.3
Limited current circuits
N/A
2.4.1/RD
General requirements See below.
N/A
2.4.2/RD
Limit values See appended table 5.3.
N/A
Frequency (Hz) ..........................................................:
-
Measured current (mA) ...............................................:
-
Measured voltage (V)..................................................:
-
Measured capacitance (F) ........................................:
-
2.4.3/RD
Connection of limited current circuits to other
circuits
N/A
5.2.4
External signalling circuits
N/A
3.5/RD
Interconnection of equipment
N/A
3.5.1/RD
General requirements
N/A
3.5.2/RD
Types of interconnection circuits
N/A
3.5.3/RD
ELV circuits as interconnection circuits
N/A
3.5.4/RD
Data ports for additional equipment
N/A
5.2.5
2.5/RD
Limited power source
For RS-232 USB, RS485 port
P
a) Inherently limited output
N/A
b) Impedance limited output
P
c) Regulating network limited output under normal
operating and single fault condition
Report No.: MTS/GEG/T13050257
N/A
Page 9 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A), max.
apparent power (VA)
--
Current rating of overcurrent protective device (A)
--
5.3
Protective earthing and bonding
P
5.3.1
General
See below.
P
2.6/RD
Provisions for earthing and bonding
See below.
P
5.3.1
2.6.1/RD
Protective earthing
UPS are class I equipments,
connection of relevant
conductive parts to the PE
terminal via green/yellow
insulated wires.
P
All eartheing is separated from
parts at hazardous voltages
P
2.6.2/RD
Functional earthing
2.6.3/RD
Protective earthing and protective bonding conductors
P
2.6.3.1/RD General
2.6.3.2/RD
Size of protective earthing conductors
P
Size of protective earthing
conductors comply with the
requirements in table 3B/RD
P
Rated current (A), cross-sectional area (mm2), AWG
2.6.3.3/RD
Size of protective bonding conductors
Size of protective earthing
conductors comply with the
requirements in table 3B/RD
P
Same as 2.6.3.1/RD
Rated current (A), cross-sectional area (mm2), AWG
2.6.3.4/RD
Resistance (Ω) of earthing conductors and their
terminations, resistance (ohm), voltage drop (V), test
current (A), duration (min)
P
Colour of insulation:
The insulation of the protective
eatthing conductor in power
cord supplied with equipment
and the protective bonding
conductor is green and yellow
P
Terminals
See below.
P
2.6.3.5/RD
2.6.4/RD
Resistance of the protective
bonding conductor is less than
0.1Ω
See table 5.3 2.6.3.3/RD Ground
continuity Test
2.6.4.1/RD General
P
2.6.4.2/RD Protective earthing and bonding terminals
P
Rated current (A), type, nominal thread diameter (mm)
Separation of the protective earthing conductor from
protective bonding conductors
P
Integrity of protective earthing
See below.
P
2.6.4.3/RD
2.6.5/RD

The earthing terminal in the
appliance inlet is regarded as the
main protective earthing terminal
Separate wiring terminals are
provided to protective earthing
conductor and protective bonding
conductor
Report No.: MTS/GEG/T13050257
Page 10 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Interconnection of equipment
This unit has it's own earthing
connection. PE terminals of
outlets reliably connected to PE
terminal of unit
2.6.5.1/RD
Verdict
2.6.5.2/RD Components in protective earthing conductors and
protective bonding conductors
P
P
2.6.5.3/RD Disconnection of protective earth
N/A
2.6.5.4/RD Parts that can be removed by an operator
N/A
2.6.5.5/RD
Parts removed during servicing
2.6.5.6/RD Corrosion resistance
2.6.5.7/RD
Screws for protective bonding
2.6.5.8/RD Reliance on telecommunication network or cable
distribution system
5.3.2
Protective earthing
The relevant potential hazard is
removed at the same time
when protective earthing
connection is disconnected for
servicing
All safety earthing connections
in compliance with Annex J.
P
P
Self-tapping screws are used to
provided protective bonding
connection and is threaded into
more than twice the pitch of the
screw thread
P
Protective earthing does not rely
on a TNV circuit
N/A
P
5.3.3
Protective bonding
P
5.4
P
5.4.1
AC and d.c. power isolation
General
3.4/RD
Disconnection from the mains supply
P
3.4.1/RD
General requirement
See below.
P
3.4.2/RD
Disconnect devices
Permanently connected
equipment
P
3.4.3/RD
Permanently connected equipment
3.4.4/RD
Parts which remain energized
3.4.5/RD
Switches in flexible cords
3.4.6/RD
Number of poles-single-phase and d.c. equipment
3.4.7/RD
Number of poles- three-phase equipment
P
3.4.8/RD
Switches as disconnect devices
P
3.4.9/RD
Plugs as disconnect devices
3.4.10/RD
Interconnected equipment
3.4.11/RD
Multiple power sources
Report No.: MTS/GEG/T13050257
P
P
N/A
No switchs in the flexible cords
N/A
N/A
Permanence connected
equipment, no plugs used
N/A
N/A
UPS under test receives power
from an AC 380V power
source
N/A
Page 11 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
5.4.2
Disconnect devices
Ungrounded battery, the
internal battery DC supply of
the UPS can be disconnected
by the quick connectors of the
battery
P
5.5
Overcurrent and earth fault protection
P
5.5.1
General
P
2.7.3/RD
Short-circuit backup protection
2.7.4/RD
2.7.5/RD
Building installation is
considered as providing.
shortcircuit
backup protection.
Number and location of protective devices ................. : Over current protection by the
Input breaker in equipment
Protection devices considered
to provide sufficient protection
against earth faults.
Protection by several devices
P
P
P
P
5.5.3
Warning to service personnel ..................................... : See user manual
Basic requirements
Equipment relies on circuit
breaker in the equipment in
regard to L to N short-circuit.
Over current protection is
provided by the built-in circuit
breaker.
Battery circuit protection
See below
5.5.3.1
Overcurrent and earth fault protection
P
5.5.3.2
Location of protective device
2.7.6/RD
5.5.2
Battery supplies are protected
by fuses located adjacent to the
batteries before any
components which may fail
short-circuited, such as
capacitors, semi-conductor
P
P
P
5.5.3.3
Rating of protective device
5.3.1/RD
Protection against overload and abnormal
operation
5.6
Protection of personnel – Safety interlocks
N/A
5.6.1
Operator protection
N/A
2.8/RD
Safety interlocks
N/A
2.8.1/RD
General principles
N/A
2.8.2/RD
Protection requirements
N/A
2.8.3/RD
Inadvertent reactivation
N/A
2.8.4/RD
Fail-safe operation
N/A
2.8.5/RD
Moving parts
N/A
Report No.: MTS/GEG/T13050257
See table4.3.
No hazards
P
P
Page 12 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
2.8.6/RD
Overriding
N/A
2.8.7/RD
Switches and relays
N/A
2.8.7.1/RD Contact gaps (mm) .................................................... :
Mechanical actuators
2.8.8/RD
N/A
2.8.7.2/RD Overload test
N/A
2.8.7.3/RD Endurance test
N/A
2.8.7.4/RD Electric strength test
N/A
5.6.2
Service person protection
N/A
There is no service person
access areas while EUT is
energized.
N/A
5.6.2.1
Introduction
N/A
5.6.2.2
Covers
N/A
5.6.2.3
Location and guarding of parts
N/A
5.6.2.4
Parts on doors
N/A
5.6.2.5
Component access
N/A
2.8.3/RD
Inadvertent reactivation
N/A
5.6.2.6
Moving parts
N/A
5.6.2.7
Capacitor banks
N/A
5.6.2.8
Internal batteries.
N/A
5.7
2.10/RD
Clearances, creepage distances and distances through insulation
2.10.1/RD
General
2.10.2/RD
Determination of working voltage
2.10.3/RD
Clearances
2.10.3.1/R
General
D
2.10.3.2/R
Clearances in primary circuits
D
2.10.3.3/R Clearances in secondary circuits
D
P
Adopt the condition-Pollution
Degree 2
Unit was connected to AC
380V(maximum) TN power
system.
See appended table 8.2
See below, Annex G was not
considered.
Annex F/RD and minimum
clearances considered.
Clearance in primary circuits
meet the requirement
Clearance in secondary circuits
meet the requirement
2.10.3.4/R Measurement of transient voltage levels
D
2.10.4/RD
P
P
P
P
P
P
N/A
Creepage distances
Cree-page distance meets the
requirement
P
CTI tests........................................................... :
CTI rating for all materials of
min. 100.
-
Report No.: MTS/GEG/T13050257
Page 13 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
2.10.5/RD
Solid insulation
See below.
2.10.5.1/R
Minimum distance through insulation
D
2.10.5.2/R Thin sheet material
D
Verdict
P
See appended table.
P
Transformer insulation sheet
and mylar sheet used
Number of layers (pcs)................................................ : Three for transformer
insulation, and one layer for my
lar sheet.
Electric strength test
3000V
2.10.5.3/R
Printed boards
D
P
Distance through insulation
P
Electric strength test for thin sheet insulating
material
-
Number of layers (pcs)............................................... :
-
2.10.5.4/R Wound components
D
Number of layers (pcs)............................................... :
2.10.6/RD
P
N/A
N/A
Two wires in contact inside wound component;
angle between 45and 90........................................ :
N/A
Coated printed boards
N/A
2.10.6.1/R General
D
N/A
2.10.6.2/R
Sample preparation and preliminary inspection
D
N/A
2.10.6.3/R Thermal cycling
D
N/A
2.10.6.4/R
Thermal ageing (C)................................................... :
D
N/A
2.10.6.5/R
Electric strength test 
D
-
2.10.6.6/R
Abrasion resistance test
D
N/A
Electric strength test
2.10.7/RD
2.10.8/RD
2.10.9/RD
-
Enclosed and sealed parts.......................................... :
N/A
Temperature T1=T2 + Tma – Tamb +10K (C) ………….... :
Spacings filled by insulating compound ..................... : Certified sources of
Photo-coupler used. No other
components applied for.
Electric strength test 
Electric strength test was
performed during the
component approval.
Component external terminations
N/A
Report No.: MTS/GEG/T13050257
P
P
Page 14 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
2.10.10/R
D
Insulation with varying dimensions
No reduction of distances
considered.
6
WIRING, CONNECTIONS AND SUPPLY
P
6.1
General
Introduction
P
6.1.1
Verdict
N/A
P
3.1/RD
3.1.1/RD
Current rating and overcurrent protection
3.1.2/RD
Protection against mechanical damage
3.1.3/RD
Securing of internal wiring
3.1.4/RD
Insulation of conductors
3.1.5/RD
Beads and ceramic insulators
3.1.6/RD
Screws for electrical contact pressure
3.1.7/RD
Insulating materials in electrical connections
3.1.8/RD
Self-tapping and spaced thread screws
All wirings meet the
requirement
P
Wires do not touch sharp
edges and heatsinks, which
could damage the insulation
and cause hazard.
Internal wirings are routed,
supported, clamped, secured
in place
P
P
P
Not used.
All screws for electrical contact
pressure are threaded into
more than two complete
threads
There is not non-metallic
material to be used in electrical
connections in EUT
No self- tapping or spaced
thread screws used for
connection of current-carrying
parts.
N/A
P
N/A
N/A
10 N pull test Test performed and passed.
P
3.1.9/RD
Termination of conductors
3.1.10/RD
Sleeving on wiring
6.1.2
6.2
Dimensions and ratings of busbars and insulated
conductors
Connection to power
6.2.1
General provisions for connection to power
3.2.2/RD
Multiple supply connections
3.2.3/RD
Permanently connected equipment
3.2.4/RD
Number of conductors, diameter (mm) of cable
and conduits .............................................................:
Appliance inlets
Report No.: MTS/GEG/T13050257
Use soldered, welded and
similar terminations for the
connection of conductors
P
Heat shrinkable tube reliable
fix on the wiring
P
P
P
P
Single supply connection
N/A
P
See table 4.3
N/A
Page 15 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
3.2.5/RD
Power supply cords
See below
Verdict
P
3.2.5.1/RD AC power supply cords
See appended table
Type .......................................................................... :
P
-
Rated current (A), cross-sectional area (mm2),
See table 4.3
AWG ..........................................................................:
3.2.5.2/RD DC power supply cords
Cord anchorages and strain relief
3.2.6/RD
N/A
P
3.2.7/RD
Protection against mechanical damage
3.2.8/RD
Cord guards
P
D (mm); test mass (g) ................................................ :
-
Radius of curvature of cord (mm) .............................. :
Means of connection ................................................. : Wire terminals
-
6.2.2
No parts under this unit likely to
damage the power supply cord.
Enclosure without sharp edges.
P
More than one supply connection .............................. : Only one supply connection
provided.
6.3
Wiring terminals for external power conductors
3.3.1/RD
Wiring terminals
P
N/A
P
permanently connected
equipments provided with
terminals in which connection
is made by means of screws
and nuts
P
3.3.2/RD
Connection of non-detachable power supply cords
P
3.3.3/RD
Screw terminals
P
3.3.4/RD
Conductor sizes to be connected
3.3.5/RD
Rated current (A), cord/cable type, crosssectional
area (mm2)................................................................. :
Wiring terminal sizes
3.3.6/RD
Rated current (A), type and nominal thread
diameter (mm) .......................................................... :
Wiring terminals design
P
3.3.7/RD
Grouping of wiring terminals
P
3.3.8/RD
Stranded wire
7
PHYSICAL REQUIREMENTS
7.1
Enclosure
7.2
Stability
4.1/RD
Angle of 10
Test: force (N) .................................................. :
Report No.: MTS/GEG/T13050257
N/A
P
-
N/A
P
The frame or chassis of EUT is
not use to carry current during
intended operation
P
See below.
The unit does not overbalance
Tilted to an angle of 10
P
232*20%=46.4N
P
P
Page 16 of 33
EN 62040-1
Clause
Requirement – Test
7.3
Mechanical strength
4.2.1/RD
General
4.2.2/RD
Steady force test, 10 N
4.2.3/RD
Steady force test, 30 N
4.2.4/RD
Steady force test, 250 N
4.2.5/RD
Impact test
Fall test
Swing test
4.2.6/RD
Drop test
4.2.7/RD
Stress relief test Test
4.2.8/RD
Cathode ray tubes
Result - Remark
Verdict
P
Tests performed and passed.
Results see below. After tests,
unit complied with the
requirements of sub-clauses
2.1.1/RD, 2.6.1/RD and
2.10/RD.
10 N applied to all components
other than enclosure.
P
P
30N, 5S to door
250 N applied to outer
enclosure.
P
See Below
No hazard as result from steel
ball fall test.
No hazard as result from steel
ball swing test.
P
P
Not required for this
equipment.
performed at 70°C no
distortion found on front panel.
No CRT in the unit.
P
P
N/A
P
N/A
Picture tube separately certified.................................. :
N/A
4.2.9/RD
High pressure lamps No high pressure lamp provided.
N/A
4.2.10/RD
Wall or ceiling mounted equipment; force (N) . :
N/A
7.4
Construction details
P
7.4.1
Introduction
P
4.3.1/RD
Edges and corners
4.3.2/RD
4.3.3/RD
4.3.4/RD
All edges and corners are
rounded and smoothed
No handles or manual controls
Handles and manual controls; force (N) ..................... : provided. No axial pull applied
to push-buttons.
There is not such adjustable
Adjustable controls
control device in EUT
There is not such part of
Securing of parts
securing in EUT
P
N/A
N/A
P
4.3.5/RD
Connection of plugs and sockets
4.3.7/RD
Heating elements in earthed equipment
No heating elements provided.
N/A
4.3.11/RD
Containers for liquids or gases
No container for liquids or
gases provided.
N/A
4.4/RD
Protection against hazardous moving part
4.4.1/RD
General
4.4.2/RD
Protection in operator access areas
N/A
4.4.3/RD
Protection in restricted access locations
N/A
4.4.4/RD
Protection in service access areas
N/A
Report No.: MTS/GEG/T13050257
N/A
N/A
No such moving part used.
N/A
Page 17 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
4.5/RD
Thermal requirements
4.5.1/RD
General
4.5.2/RD
Temperature tests
P
Normal load condition per Annex L
--
P
See table 7.7 for details.
P
4.5.3/RD
Temperature limits for materials
See Table 7.7 for details.
P
4.5.4/RD
Touch temperature limits
See Table 7.7 for details.
P
4.5.5/RD
Resistance to normal heat
P
7.4.2
Openings
(see appended table 7.7)
EUT are equipped with DC fan
to vented. No arcing
component is adjacent to
batteries
7.4.3
Gas concentration
7.4.4
Equipment movement
7.5
4.7/RD
4.7.1/RD
4.7.2/RD
N/A
No castors provided.
N/A
Resistance to fire
Reducing the risk of ignition and spread of
flame
Method 1, selection and application of
components wiring and materials
Method 2, application of all of simulated fault
condition tests
Conditions for a fire enclosure
4.7.2.1/RD Parts requiring a fire enclosure
P
P
See below.
P
Use of materials with the
required flammability classes.
P
N/A
See below.
With having the following
components:
Components in primary circuits
P
P
Insulated wiring
The fire enclosure is required.
4.7.2.2/RD Parts not requiring a fire enclosure
Materials
4.7.3/RD
4.7.3.1/RD General
4.7.3.2/RD Materials for fire enclosures
N/A
P
PCB rated accordingly. For
details see table 4.3.
Metal enclosure with
thermoplastic front panel. For
details see table 4.3.
P
P
4.7.3.3/RD Materials for components and other parts
outside fire enclosures
4.7.3.4/RD Materials for components and other parts inside
fire enclosures
See subclause 4.7.2/RD.
4.7.3.5/RD Materials for air filter assemblies
No air filters provided.
N/A
4.7.3.6/RD Materials used in high-voltage components
No high voltage components
provided.
N/A
Report No.: MTS/GEG/T13050257
N/A
Internal components except
small parts are V-2, HF-2 or
better.
Batteries have a flammability
class of HB (or better).
P
Page 18 of 33
EN 62040-1
Clause
Requirement – Test
7.6
Battery location
7.6.1
Battery location and installation
7.6.2
Accessibility and maintainability
7.6.3
Distance
7.6.4
Case insulation
P
5.2/RD
Electric strength
P
5.2.1/RD
General
P
5.2.2/RD
P
7.6.5
Test procedure
Wiring
7.6.6
Electrolyte spillage
7.6.7
Ventilation
7.6.8
Charging voltages
7.7
Temperature rise
Maximum temperatures
Result - Remark
Verdict
P
Separate battery rooms
P
P
The batteries are fixed in place
and the temperature of
mounting parts meet
requirement of less than 45
degree temperature rise
Contact, connections and
wiring are protected against
effects of ambient tem.,
moisture, gas, vapour and
mechanical stress.
EUT are equipped with VRLA
type batteries.
EUT are equipped with DC fan
to vented.
No arcing component is
adjacent to batteries
No hazards
P
P
N/A
P
P
P
No excessive temperatures
P
4.5/RD
Thermal requirements
P
4.5.1/RD
General
4.5.2/RD
Temperature tests
P
Normal load condition per Annex L
--
See table 7.7 for details.
P
4.5.3/RD
Temperature limits for materials
See Table 7.7 for details.
P
4.5.4/RD
Touch temperature limits
See Table 7.7 for details.
P
4.5.5/RD
Resistance to normal heat
See Table 7.7 for details.
P
8
8.1
5.1.1/RD
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
General provisions for earth leakage
P
Earth leakage current
5.1.2/RD
Equipment under test (EUT)
5.1.7/RD
Equipment with touch current exceeding 3.5 mA :
Report No.: MTS/GEG/T13050257
See subclause 5.1.2/RD below.
Only one AC main supply
P
Touch current of the equipment
does not exceed 3.5 mA.
P
P
Page 19 of 33
EN 62040-1
Clause
Requirement – Test
8.2
Electric strength
5.2.1/RD
General
See appended table 8.2.
P
5.2.2/RD
Test procedure
See appended table 8.2.
P
8.3
Abnormal operating and fault conditions
P
8.3.1
General
P
5.3.1/RD
No hazards
P
5.3.2/RD
Protection against overload and abnormal
operation
Motors
DC fan are blocked off
P
5.3.3/RD
Transformers
See appended Annex C.
P
5.3.4/RD
Functional insulation ................................................ :
EUT meet the requirement
P
5.3.5/RD
Electromechanical components
No electromechanical
component (except for
approved relays) provided.
N/A
5.3.9/RD
Compliance criteria for abnormal operating and
fault conditions
5.3.9.1/RD During the tests
5.3.9.2/RD After the tests
Result - Remark
Verdict
P
P
---No fire accurs
---EUT do not emit molten
metal
---Enclosures do not deform
After all abnormal test
---reinforced and basic
insulation does show visible
signs of damage
---the clearance and
creepage distance do not
reduce below the value
specified in 2.10/RD
P
P
8.3.2
Simulation of faults
No hazards
P
8.3.3
Conditions for tests
No hazards
P
9
CONNECTION TO TELECOMMUNICATION NETWORKS
P
6.1/RD
Protection of telecommunication network service persons, and users of other equipment
connected to the network, from hazards in the equipment
Protection from hazardous voltages
P
6.1.1/RD
Separation of the telecommunication network from
6.1.2/RD
earth
6.1.2.1/RD Requirements
Test voltage (V) ......................................................... : 3kV
Current in the test circuit (mA) ................................... : Not exceed 10mA
6.1.2.2/RD Exclusions ................................................................. :
Protection of equipment users from overvoltages on telecommunication networks
6.2/RD
6.2.1/RD
Separation requirements
Report No.: MTS/GEG/T13050257
P
P
P

N/A
P
P
Page 20 of 33
EN 62040-1
Clause
Requirement – Test
6.2.2/RD
Electric strength test procedure
Result - Remark
Verdict
P
6.2.2.1/RD Impulse test
6.2.2.2/RD Steady-state test
P
6.2.2.3/RD Compliance criteria
Protection of the telecommunication wiring system
6.3/RD
from overheating
Max. output current (A) .............................................. :
P
P
N/A
-
Current limiting method.............................................. :
-
2.1.3/RD
Protection in restricted access locations
2.3/RD
TNV circuits
P
2.3.1/RD
Limits
P
Type of TNV circuits................................................... :
-
Separation from other circuits and from
accessible parts
P
Insulation employed .................................................. :

Separation from hazardous voltages
P
Insulation employed ................................................... :

2.3.2/RD
2.3.3/RD
2.3.4/RD
The unit is not limited to be
used in restricted access
locations.
Connection of TNV circuits to other circuits
Insulation employed .................................................. :
2.3.5/RD
Test for operating voltages generated externally
2.6.5.8/RD Reliance on telecommunication network or
cable distribution system
2.10.3.3/R Clearances in secondary circuits
D
N/A
N/A

N/A
P
P
2.10.3.4/R
D
Measurement of transient voltage levels
2.10.4/RD
Creepage distances
3.5/RD
Interconnection of equipment
N/A
3.5.1/RD
General requirements
N/A
3.5.2/RD
Types of interconnection circuits....................... :
N/A
P
CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1/RD)
M/RD
ANNEX M,
Introduction
M.1/RD
P
P
P
M.2 /RD
Method A
P
M.3/RD
Method B
N/A
M.3.1/RD
Ringing signal
P
M.3.1.1/R
Frequency (Hz) ......................................................... : <70Hz

Report No.: MTS/GEG/T13050257
Page 21 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
D
M.3.1.2/R
D
Voltage (V) ............................................................... : <300V
M.3.1.3/R
D
Cadence; time (s), voltage (V) .................................. : 8s, Not exceed 56.5V
M.3.1.4/R
D
Single fault current (mA) .......................................... :
M.3.2/RD
Tripping device and monitoring voltage ................... :
P
M.3.2.1/R
D
Conditions for use of a tripping device or a
monitoring voltage
P
M.3.2.2/R
D
Tripping device
M.3.2.3/R
D
Monitoring voltage (V) .............................................. : Not exceed 56.5V
A/RD
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
A.1/RD
Flammability test for fire enclosures of movable
Metal enclosure
equipment having a total mass exceeding 18kg, and of
stationary equipment (see 4.7.3.2)
A.1.1/RD
Not exceed 56.5mA



P
-
N/A
N/A
Samples …………………………….……………………:
-
Wall thickness (mm) ……………………………………:
-
A.1.2/RD
Conditioning of samples; temperature (℃) …………..:
N/A
A.1.3/RD
Mounting of samples ……………………………………:
N/A
A.1.4/RD
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ………………………………………:
A.1.6/RD
A.2/RD
A.2.1/RD
A.2.2/RD
-
Test procedure
N/A
Compliance criteria
N/A
Sample 1 burning time (s) ……………………………..:
-
Sample 2 burning time (s) ……………………………..:
-
Sample 3 burning time (s) ……………………………...:
-
Flammability test for fire enclosures of movable
equipment having a total mass not exceeding 18kg,
and for material and components located inside fire
enclosures (see 4.7.3.2 and 4.7.3.4)
N/A
Samples, material ………………………………………:
-
Wall thinkness (mm)
-
Conditioning of samples
Report No.: MTS/GEG/T13050257
N/A
Page 22 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
A.2.3/RD
Mounting of samples
N/A
A.2.4/RD
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C …………………………………………:
Verdict
-
A.2.5/RD
Test procefure
N/A
A.2.6/RD
Compliance criteria
N/A
A.2.7/RD
Sample 1 burning time (s) ……………………………..:
-
Sample 2 burning time (s) ……………………………..:
-
Sample 3 burning time (s) ……………………………..:
Alternative test acc. to IEC 60695-2-2, cl. 4 and
8
N/A
Sample 1 burning time (s) ……………………………..:
-
Sample 2 burning time (s) ……………………………..:
-
Sample 3 burning time (s) ……………………………..:
-
A.3/RD
Hot flaming oil test (see 4.6.2)
N/A
A.3.1/RD
Mounting of samples
N/A
A.3.2/RD
Test procedure
N/A
A.3.3/RD
Compliance criterion
N/A
B/RD
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2/RD
and 5.3.2/RD)
B.1/RD
General requirements
d.c. fan motors in
SECONDARY CIRCUITS
P
Position …………………………………………………:
Rear of the enclosure
-
Manufacturer ……………………………………………:
See table 4.3
-
Type ……………………………………………………..:
See table 4.3
-
Rated values ……………………………………………:
See table 4.3
-
B.2/RD
Test conditions
The test in the equipment
P
B.3/RD
Maximum temperatures
No excessive temperatures
P
B.4/RD
Running overload test
N/A
B.5/RD
Locked-rotor overload test
N/A
P
Test duration (days) …………………………………….:
-
Electric strength test: test voltage (V) …………………:
-
B.6/RD
Running overload test for d.c. motors in secondary
circuits
B.6.1/RD
General
N/A
B.6.2/RD
Test procedure
N/A
B.6.3/RD
Alternative test procedure
N/A
Report No.: MTS/GEG/T13050257
No possible
N/A
Page 23 of 33
EN 62040-1
Clause
Requirement – Test
Result - Remark
Verdict
B.6.4/RD
Electric strength test
B.7/RD
Locked-rotor overload test for d.c. motors in secondary
circuits
P
B.7.1/RD
General
P
B.7.2/RD
Test procedure
B.7.3/RD
Alternative test procedure; test time (h) ………………: Temp. not exceed the values
specified in Table B.1. after
test 2h until steady conditions
are established
N/A
Block until steady conditions
are established
P
B.7.4/RD
Electric strength test
B.8/RD
Test for motors with capacitors
N/A
B.9/RD
Test for three-phase motors
N/A
B.10/RD
Test for series motors
N/A
C/RD
Operation voltage Not exceed
60 V d.c
P
N/A
Operating voltage (V) …………………………………..:
-
ANNEX C, TRANSFORMERS (see 1.5.4/RD and 5.3.3/RD)
P
Position ………………………………………….………..: See table 4.3
-
Manufacturer ………………………..……………………:
-
Type ………………………………………..……………..:
-
Rated values …………………………………….………:
-
Method of protection ……………………….……………:
-
C.1/RD
Overload test
C.2/RD
Insulation
No excessive temperature
P
P
Protection from displacement of windings ……………:
N/A
Safety isolation transformer
P
With AC 3000V after humidity treatment
Result
-
D/RD
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4/RD)
P
D.1/RD
Measuring instrument
P
D.2/RD
Alternative measuring instrument
E/RD
TEMPERATURE RISE OF A WINDING (see 1.4.13)
Thermocouple method used
Report No.: MTS/GEG/T13050257
Not used
N/A
N/A
Page 24 of 33
EN 62040-1
Clause
Requirement – Test
F/RD
MEASURING OF CLEARANCES AND CREEPAGE DISTANCES (see 2.10)
G/RD
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1/RD
General
N/A
G.1.1/RD
General
N/A
G.1.2/RD
Summary of the procedure for determining minimum
clearances
N/A
G.2/RD
Determination of mains transient voltage (V) ………..:
N/A
G.2.1/RD
AC mains supply
N/A
G.2.2/RD
Earthed d.c. mains supplies
N/A
G.2.3/RD
Unearthed d.c. mains supplies
N/A
G.2.4/RD
Battery operation
N/A
G.3/RD
Determination of telecommunication network transient
voltage (V) ………………………………………………:
N/A
G.4/RD
Determination of required withstand voltage (V) ……..:
N/A
G.4.1/RD
Mains transients and internal repetitive peaks
N/A
G.4.2/RD
Transients from telecommunication networks
N/A
G.4.3/RD
Combination of transients
N/A
G.4.4/RD
Transients from cable distribution systems
N/A
G.5/RD
Measurement of transient levels (V) ………………….:
N/A
G.6/RD
Determination of minimum clearances ……………….:
N/A
H/RD
ANNEX H, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
AND FOREIGN OBJECTS (see IEC 60529)
N/A
J/RD
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6/RD)
P
Metal used ………………………………………………:
Result - Remark
Verdict
P
Screw: steel plated with Zn;
Enclosure: mild metal
Nut and washer: steel plated
with Zn
The max electrochemical
potential is :0. 3V for metal with
Zn
-
K/RD
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1/RD
Marking and breaking capacity
N/A
K.2/RD
Thermostat reliability; operating voltage (V) …………:
N/A
Report No.: MTS/GEG/T13050257
Page 25 of 33
EN 62040-1
Clause
Requirement – Test
K.3/RD
Thermostat endurance test; operating voltage (V) ….:
N/A
K.4/RD
Temperature limiter endurance; operating voltage (V) :
N/A
K.5/RD
Thermal cut-out reliability
N/A
K.6/RD
Stability of operation
N/A
L
ANNEX L, BACKFEED PROTECTION TEST
L.1
General
See L.2 below.
L.2
Test for pluggable equipment type A or
pluggable equipment type B UPS
No pluggable equipment
L.3
Test for permanently connected UPS
L.4
Single-fault conditions
M
ANNEX M, EXAMPLES OF REFERENCE LOAD CONDITIONS
P
M.1
General
P
M.2
Reference resistive load
N/A
M.3
Reference inductive-resistive load
N/A
M.4
Reference capacitive-resistive loads
Result - Remark
Verdict
P
P
N/A
P
No hazards
P
See below.
Worst-case power factors as
specified by the manufacturer
maintained during the relevant
tests.
P
M.5
Reference non-linear load
N/A
M.5.1
Test method
N/A
M.5.2
Connection of the non-linear reference load
N/A
N
ANNEX N, VENTILATION OF BATTERY COMPARTMENTS
P
N.1
General
P
N.2
Hydrogen concentration
N.3
Blocked conditions
N.4
Overcharge test
U/RD
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4/RD)
N/A
U.1/RD
Wire construction
N/A
U.2/RD
Type tests
N/A
U.2.1/RD
Electric strength
N/A
Report No.: MTS/GEG/T13050257
See N.1 above.
comply with require even if the
fan is blocked
P
No hazards
P
No such wires used
P
Page 26 of 33
EN 62040-1
Clause
Requirement – Test
U.2.2/RD
Flexibility and adherence
N/A
U.2.3/RD
Heat shock
N/A
U.2.4/RD
Retention of electric strength after bending
N/A
U.3/RD
Tests during manufacture
N/A
U.3.1/RD
Routine testing
N/A
U.3.2/RD
Sampling tests
N/A
X
ANNEX X, GUIDANCE FOR DISCONNECTION OF BATTERIES DURING SHIPMENT
N/A
X.1
Applicable products
X.2
Battery disconnection
N/A
X.3
Package labelling/marking
N/A
X.4
Damage inspection
N/A
X.5
The importance of safe handling procedures
N/A
Y/RD
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see clause 4.3.13.3/RD)
N/A
Y.1/RD
Test apparatus ………………………………………….:
N/A
Y.2/RD
Mounting of test samples ………………………………:
N/A
Y.3/RD
Carbon-arc light-exposure apparatus …………………:
N/A
Y.4/RD
Xenon-arc light exposure apparatus …………………..:
N/A
Report No.: MTS/GEG/T13050257
Result - Remark
Currently this annex is only
informative.
Verdict
N/A
Page 27 of 33
4.3
TABLE: list of critical components and materials
Object/Part No. Manufacturer /Trademark
P
Type/Model
Technical Data2)
Mark(s) of
Conformity1)
Wire
Shenzhen Jinyangguang Wire &
Cable Co., Ltd.
60227 IEC
02(RV)
4mm2 450/750V
TUV
Alt.
Guangzhoushi Qiguang Cables &
Wires Co.,Ltd
60227 IEC
02(RV)
4mm2 450/750V
TUV
Alt.
Various
60227 IEC
02(RV)
4mm 450/750V
Wire
Guangzhoushi Qiguang Cables &
Wires Co.,Ltd
IEC 02(RV)
Alt.
Shenzhen Jinyangguang Wire &
Cable Co., Ltd.
60227 IEC
02(RV)
Alt.
Various
60227 IEC
02(RV)
Fuse
BUSSMANN
170M5412
630A/690V
VDE & UL
Fuse
LITTEL FUSE
KLK D30
30A/600V
UL E81895
Relay
TYCO Electronics
277VAC/30A
VDE 40019600
DC fan
PELKO MOTORS INC
12V/0.819A
VDE & UL
IGBT
Infineon
1200V/40A
CE
IGBT
IR
900V/28A
CE
Thyristor
IXYS
CLA50E120
0HB
1200V/50A
CE
Thyristor
SEMIKRON
SK100KQ12 1200V/101A
CE
IR
RHRG75120 1200V/75A
CE
Shenzhen Su Rong Capacitors
MPX
280V 474 K(±10%)
VDE 40008924
X -cap.
Shenzhen Su Rong Capacitors
MPX
280V 0.1uF
VDE 40008924
X -cap.
Shenzhen Su Rong Capacitors
MPX
280VAC/3.3uF
VDE 40008924
X -cap.
Tenta Electric Industrial Co. Ltd.
MEX
275V,2.2uF
VDE 119119
Y -cap.
Murata Mfg. Co., Ltd.
KX
250V,470pF
VDE 4002831
Y -cap.
Yinan Don's Electronic
Component Co., Ltd.
MKP
250V,103K
VDE 135256
PCB
Various
Various
130℃, 94V-0
UL
Inductor
Shenzhen Yuyuan Power Co. Ltd.
PFC Chock,
PPI226040
Inductor
BO LUO DA XIN ELECTRIC CO
LTD
PFC Chock,
PPI226040
800uH±
10%,20HKz
800uH±
10%,20HKz
Test with the
appliance
Test with the
appliance
Fast Recovery
Diode
X -cap.
Report No.: MTS/GEG/T13050257
T92S7D12-1
2
R9238M12B
PCB1-7
IKW40N120
H3
IRG4PF50W
PBF
2
95mm2, 70mm2
2
2
4mm , 35mm ,
2
25mm ,450/750V
95mm2, 70mm2
4mm2 , 35mm2,
2
25mm ,450/750V
95mm2, 70mm2
4mm2 , 35mm2,
25mm2 ,450/750V
TUV
TUV
TUV
TUV
Page 28 of 33
Object/Part No. Manufacturer /Trademark
Wire
Varnish
PCB
TAI-I ELECTRIC WIRE & CABLE
CO LTD
HANG CHEUNG
PETROCHEMICAL LTD
KINGBOARD LAMINATES
HOLDINGS LTD
Type/Model
Technical Data2)
Mark(s) of
Conformity1)
EIW
180℃,94V-0
UL E85640
8562/C
130℃
UL E200154
KB-6150
130℃, 94V-0
UL E123995
Tape
JINGJIANG YAHUA PRESSURE
SENSITIVE GLUE CO., LTD
PZ
130℃,94V-0
UL E165111
Epoxy
DONGGUAN EATTO
ELECTRONIC MATERIAL CO
LTD
3300A/B-1
130℃, V-0
UL E218090
Inductor
Shenzhen Yuyuan Power Co. Ltd.
INV Chock,
PPF226026
620uH±10%, 30A
Inductor
BO LUO DA XIN ELECTRIC CO
LTD
PFC Chock,
PPI226040
800uH±
10%,20HKz
Test with the
appliance
Test with the
appliance
-Wire
TAI-I ELECTRIC WIRE & CABLE
CO LTD
EIW
180℃,94V-0
UL E85640
-Spacer
KINGBOARD LAMINATES
HOLDINGS LTD
FR-4
130℃, 94V-0
UL E123995
-Epoxy
WINNING HI-TECH CO LTD
WK-969A
90℃, V-0
UL E87252
SUZHOU TAIHU ELECTRIC
ADVANCED MATERIAL CO LTD
JEPULS TECHNOLOGY
(SHENZHEN) CO., LTD
T-4260(a)
130℃
UL E228349
EA66II IGBT 1KHz
DRV
Transformer
BO LUO DA XIN ELECTRIC CO
LTD
EA66II SCR
DRV
1KHz
Transformer
BO LUO DA XIN ELECTRIC CO
LTD
EE33
100W, 1.0mH
Test with the
appliance
Test with the
appliance
Test with the
appliance
-Bobbin
CHANG CHUN PLASTICS
Phenolic
T375J
94V-0
UL E59481
-Core
KAIYUAN
EPC13 KP4
--
--
-Wire
TAI-I ELECTRIC WIRE & CABLE
CO LTD
MW75
130℃,94V-0
UL E85640
-Alt.
CHENG WEI INDUSTYR CO LTD 2UEW
130℃,94V-0
UL E227475
-Alt.
FENG CHING METAL CORP.
2UEW
130℃,94V-0
UL E172395
-Alt.
PACIFIC ELECTRIC WIRE &
CABLE CO.,LTD
UEW
130℃,94V-0
UL E201757
-Tape
JINGJIANG YAHUA PRESSURE
SENSITIVE GLUE CO., LTD
CT-280
130℃
UL E165111
-Alt.
XINYU SHENGDAFENG
ELECTRIC MATERIAL CO., LTD
SDF-3 12
130℃,94V-0
UL E317896
-Varnish
HANG CHEUNG
PETROCHEMICAL LTD
130℃
UL E200154
-Alt.
YUEYANG GREEN
TECHNOLOGY CO., LTD
130℃
UL E303754
-Varnish
Transformer
Report No.: MTS/GEG/T13050257
8562/C
8562E
JX1150Y
8-1N
Page 29 of 33
Object/Part No. Manufacturer /Trademark
Type/Model
Technical Data2)
Mark(s) of
Conformity1)
-Teflon Tube
CHANGYUAN ELECTRONICS
(SHENZHEN) CO LTD
CB-TT
200℃
UL E180908
-Alt.
GREAT HOLDING INDUSTRIAL
CO., LTD
CB-TT-L
200℃
UL E156256
WF
130℃,94V-0
UL E165111
#1350F
130℃,94V-0
UL E17385
#1350F
130℃, 94V-0
UL E17385
-Margin tape
-Alt.
-Alt.
4.6
EUT
JINGJIANG YAHUA PRESSURE
SENSITIVE GLUE CO LTD
3M COMPANY ELECTRICAL
MARKETS DIV (EMD)
3M COMPANY ELECTRICAL
MARKETS DIV (EMD)
TABLE: input current test
Fuse#
P
Rated(A) U(V)
P(Kw)
I(A)
I fuse(A)
Condition/status
EA66400 Input breaker
545
342Vac
171.68
502
502
Normal operation at rated load
EA66400 Input breaker
545
380Vac
171.76
452
452
Normal operation at rated load
EA66400 Input breaker
545
402.8Vac 171.59
426
426
Normal operation at rated load
By AC mains supply
Note(s): measure the input currents with full load.
(Loaded with empty battery charging and rated output full load)
5.3
2.6.3.4/RD
TABLE: Provisions for protective earthing
P
EUT
Location
Resistance measured(mΩ)
comments
EA66400
I/P earth →O/P earth
I/P earth →metal enclosure
I/P earth →earth on PCB
0.018
0.026
0.026
Tested at 250A/10munites
Tested at 250A/10munites
Tested at 250A/10munites
7.7
TABLE: maximum temperatures
P
Test voltage (V) ……….…:
-
See below
t1(℃) ……..………………..: --
-
t2(℃) …………………..…..:
-
--
Maximum temperature T of part/at:
T (℃)
342V/ 50Hz
T (℃)
402.8V/ 50Hz
Allowed Tmax(℃)
-
-
-
-
Connector
39.2
54.0
38.6
53.5
95
Input wire
38.5
53.3
36.7
51.6
105
Output wire
36.8
51.6
36.3
51.2
105
DC battery connector
32.3
47.1
32.5
47.4
95
DC wire
34.8
49.6
34.8
49.7
105
Report No.: MTS/GEG/T13050257
Page 30 of 33
PCB near fuse
32.6
47.4
32.6
47.5
130
RY1 body
38.2
53.0
39.3
54.2
130
RY4 body
40.4
55.2
42.2
57.1
130
T1 coil
63.1
77.9
64.5
79.4
130-10=120
C10 body
36.2
51.0
36.6
51.5
105
PCB near Q1 body
58.8
73.6
58.5
73.4
130
RY2 near panel
33.3
48.1
34.3
49.2
130
DC fan body
38.2
53.0
38.8
53.7
85
U3 body
33.6
48.4
33.6
48.5
130
Transformer coil(near RS232)
46.8
61.6
43.7
58.6
130-10=120
Panel
29.1
43.9
29.7
44.6
85
Enclosure of Main module
30.3
45.1
29.9
44.8
60
Ambient
25.2
40.0
25.1
40.0
--
Note(s): 1. The temperatures were measured under worst normal mode defined in 1.2.2.1 and as described in
1.2.2.1 and as described in sub-clause 1.6.2 and at voltages as described above.
2. The maximum ambient temperature permitted by the manufacturer’s specification is 40℃
8.1
TABLE: earth leakage current
P
EUT
Condition
L→PE
(mA)
N→PE
(mA)
Limit
(mA)
EA66400
Line mode
RS232 to L/N
RS485 to L/N
USB
2.93
0.001
0.001
0.002
2.92
0.001
0.001
0.002
3.5
0.25
0.25
0.25
5.3,7 and 8.2
Swith on
Swith on
Swith on
Swith on
TABLE:electric strength tests,impulse tests and voltage surge tests P
Test voltage applied between:
Test voltage(V)
Breakdown
Yes/No
Primary to SELV(RS-232)
3000Vac
No
Primary to SELV(RS485)
3000Vac
No
Primary to SELV(USB)
3000Vac
No
Input L/N to front Panel
1500Vac
No
Input L/N to earth
1500Vac
No
Output L/N to earth
1500Vac
No
T1 (Pri-Sec) (main board)
3000Vac
No
Report No.: MTS/GEG/T13050257
Page 31 of 33
7.5 and
8.3
Component
No.
TABLE:fault condition tests
P
Ambient temperature (℃)
25℃
--------
Model/type of power supply
See nameplate for details
--------
Manufacturer of power supply
See nameplate for details
--------
Rated markings of power supply
See nameplate for details
--------
Fault
Test voltage
Fuse
Test time
(V)
No.
Fuse current
Result
(A)
Max. temperature:
(main board)
TX1 coil: 76.3 ℃
DC Fan
Block
402.8
2hours
--
--
TX1 coil: 70.3℃
PCB near Q1 body:84.0℃
Ambient: 25.0℃
Recoverble, no hazard.
Max. temperature:
(main board)TX1 coil:
76.5℃,TX1 coil : 72.3℃
Ventilation
Block
402.8
1hours
--
--
PCB near Q1 body:106.4℃
Ambient: 24.5℃
After 30nins, display: 41.no
output voltage.
Max. temperature:
(main board)
TX1 coil: 86.5 ℃
DC Fan
Block
DC 240V
2hours
(by
batteries)
--
--
TX1 coil: 80.4℃
PCB near Q1 body:83.0℃
Ambient: 25.0℃
Recoverble, no hazard.
Max. temperature:
(main board)TX1 coil: 86.5
Ventilation
Block
DC
240V(by 1hours
batteries)
℃,TX1 coil : 82.5℃
--
--
PCB near Q1 body:105.3℃
Ambient: 25.1℃
After 30nins, display: 41.no
output voltage.
T01 Pin 1-2(main
board)
s-c
380
4mins
--
--
Unit working abnormal, no hazard.
T01 Pin 6-7(main
board)
s-c
380
4mins
--
--
Unit working abnormal, no hazard.
s-c
380
4mins
--
--
Unit working abnormal,, no hazard.
s-c
380
5mins
--
--
Unit shutdown immediately or
T1 (near
RS232)
Other transformer
Report No.: MTS/GEG/T13050257
Page 32 of 33
abnormal,No damaged, no hazards
C1
s-c
380
4mins
--
--
U1 Pin1-2
U1 Pin3-4
U2 Pin1-2
U2 Pin3-4
s-c
s-c
s-c
s-c
380
380
380
380
4mins
4mins
4mins
4mins
-----
-----
Q1 1-2
s-c
380
4mins
--
--
Unit working abnormal, nonrecoverable.
Unit working abnormal, no hazard.
Unit working abnormal, no hazard.
Unit working abnormal, no hazard.
Unit working abnormal, no hazard.
Unit working abnormal,
non-recoverable, no hazard
Note(s): s-c means short-circuit.o-l means overload.o-c means open-circuit.
Report No.: MTS/GEG/T13050257
Page 33 of 33
Appendix 1
Whole views of ‘Online High Frequency UPS’
Model: EA66400
Appendix 2
Whole views of ‘Online High Frequency UPS’
Model: EA66400
Appendix 3
Whole views of ‘Online High Frequency UPS’
Model: EA66400
Appendix 4
Whole views of ‘Online High Frequency UPS’
Model: EA66400
Appendix 5
Internal view of ‘Online High Frequency UPS’
Model: EA66400
Appendix 6
Internal view of ‘Online High Frequency UPS’
Model: EA66400
Appendix 7
Internal view of ‘Online High Frequency UPS’
Model: EA66400
Appendix 8
Internal view of ‘Online High Frequency UPS’
Model: EA66400
Appendix 9
Main module views of ‘Online High Frequency UPS’
Model: EA66400
Appendix 10
Main module inner views of ‘Online High Frequency UPS’
Model: EA66400
---END OF REPORT---
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement