Socomec NET VISION UPS Network Integrator User Guide

UPS NETWORK INTEGRATOR
User Guide
IOMNETVIXX00-GB_08.doc
At and IBM are registered trademarks of International Business Machines Corporation.
NetWare is a registered trademark of Novell Incorporated.
DOS, Windows 95 / 98 / ME and Windows NT/ 2000/Xp are registered trademarks of
Microsoft (R) Corporation.
All other trademarks belong to their respective owners.
2
1. ELECTROMAGNETIC EMISSION NOTICE
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B (DoC) digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful electromagnetic interference when the equipment is used in a commercial environment.
CE Notice
This device complies with the EMC directive 89/336/EEC of the European Community and meets or exceeds
the following technical standards:
3
2. SAFETY INFORMATION
For NET VISION/Card
¾
Qualified service personnel must perform all operations performed on this equipment. Remove rings,
watches and other jewellery before installing the unit.
For NET VISION/Box
¾
¾
¾
¾
¾
¾
To reduce the risk of fire or electric shocks install the unit in a temperature-controlled indoor area free of
conductive contaminants. Do not place the unit near liquids or in an excessively humid environment.
Do not allow liquids or foreign objects to enter the unit
The unit does not contain any customer-replaceable parts. Do not open the unit.
Qualified personnel must perform all operations on this equipment. Remove rings, watches and other
jewellery before installing the unit.
Before maintenance, repair or shipment, the unit must be completely switched off, unplugged and all
connections must be removed.
Make sure that the mains rating is compatible with the power adapter rating before connecting the NET
VISION/Box.
4
1.
ELECTROMAGNETIC EMISSION NOTICE__________________________________________________ 3
2.
SAFETY INFORMATION __________________________________________________________________ 4
For NET VISION/Card _______________________________________________________________________ 4
For NET VISION/Box ________________________________________________________________________ 4
3.
CHAPTER 1 – NET VISION OVERVIEW _____________________________________________________ 7
Functions _________________________________________________________________________________ 7
Features __________________________________________________________________________________ 8
System Operation ___________________________________________________________________________ 9
Layout of NET VISION Connections ___________________________________________________________ 10
4.
CHAPTER 2 - NET VISION INSTALLATION ________________________________________________ 11
Hardware Installation ______________________________________________________________________
NET VISION/Card Installation________________________________________________________________
NET VISION/Box Installation_________________________________________________________________
Preparation_______________________________________________________________________________
NET VISION Configuration via serial port ______________________________________________________
NET VISION Configuration (with Windows) _____________________________________________________
IP Address, Gateway Address, Network Mask and Date/Time (System Group Setting) _____________________
Login Passwords And Available Protocols (Control Group Setting) ___________________________________
General Information and Poll Rate (Parameter Group Setting) ______________________________________
E-Mail Parameters (SMTP Group Setting) ______________________________________________________
E-Mail Receivers Table _____________________________________________________________________
Access Policies (Access Control Table Setting) ___________________________________________________
Trap Receivers Setting ______________________________________________________________________
End of NET VISION Configuration ____________________________________________________________
NET VISION Configuration via Ethernet ________________________________________________________
NET VISION/Card Hardware Preparation ______________________________________________________
NET VISION/Box hardware Preparation ________________________________________________________
Changing the routing settings on a PC__________________________________________________________
Finding the NET VISION IP address ___________________________________________________________
Running the TELNET Command ______________________________________________________________
Running the Web Browser (Netscape, Internet Explorer, etc.)________________________________________
Initial Configuration Setup ___________________________________________________________________
Configuring basic NET VISION parameters via Web Browser _______________________________________
Enabling/Disabling network protocols and NET VISION Reset_______________________________________
5.
CHAPTER 3 – WEB BROWSER OPERATIONS ______________________________________________ 29
Using a Web Browser to view the NET VISION Home Page _________________________________________
Description of the Menus ____________________________________________________________________
UPS Monitor______________________________________________________________________________
UPS Management __________________________________________________________________________
Net Vision Mgmt ___________________________________________________________________________
SNMPv3 USM Table________________________________________________________________________
SNMP Trap Receivers_______________________________________________________________________
SNMP/HTTP Access Control _________________________________________________________________
Homepage Refresh Rate _____________________________________________________________________
UPS History ______________________________________________________________________________
6.
29
29
29
36
42
44
45
46
46
46
CHAPTER 4 - SNMP NMS USER OPERATIONS______________________________________________ 47
NET VISION SNMP Configuration parameters ___________________________________________________
IP Write Access Setting______________________________________________________________________
Trap Receivers Setting ______________________________________________________________________
SNMP Management Software Set Up ___________________________________________________________
NET VISION and SNMP _____________________________________________________________________
7.
11
11
12
12
13
14
17
18
19
19
20
21
22
22
23
23
23
24
24
26
26
27
27
28
47
47
47
47
47
CHAPTER 5 - SHUTDOWN SOFTWARE ____________________________________________________ 50
5
Supported Operating Systems_________________________________________________________________
Using Shutdown Software On Windows _________________________________________________________
View connected devices using a Web Browser ____________________________________________________
View the connected devices using SNMP NMS____________________________________________________
Uninstalling Shutdown Software_______________________________________________________________
Using shutdown software on Novell NetWare ____________________________________________________
Using shutdown software on Sco UnixWare______________________________________________________
Using the shutdown software on Sco OpenServer _________________________________________________
Using shutdown software on Sun Solaris ________________________________________________________
Using the shutdown software on Linux__________________________________________________________
8.
CHAPTER 6: UPS POWER CRISIS MANAGEMENT__________________________________________ 67
UPS Management __________________________________________________________________________
UPS Control Menu _________________________________________________________________________
Forcing UPS To Stand-By ___________________________________________________________________
Programming The UPS Shutdown Schedule______________________________________________________
Programming UPS shutdown events ___________________________________________________________
Display of automatic warning messages_________________________________________________________
9.
83
83
84
84
APPENDIX C - EMD SENSOR ___________________________________________________________ 85
Introduction ______________________________________________________________________________
Features _________________________________________________________________________________
Installation _______________________________________________________________________________
________________________________________________________________________________________
13.
78
78
79
79
80
80
81
81
81
82
82
APPENDIX B – FIRMWARE UPGRADE __________________________________________________ 83
General Information ________________________________________________________________________
Firmware Upgrade using Unix________________________________________________________________
Firmware Upgrade using Windows 95/98/ME/NT4.0/2000/Xp _______________________________________
Program Features__________________________________________________________________________
12.
74
74
75
76
76
77
APPENDIX A - TECHNICAL INFORMATION _____________________________________________ 78
NET VISION/Card Technical Information _______________________________________________________
Technical Specifications _____________________________________________________________________
NET VISION/Card Layout And Pin Assignment___________________________________________________
Description of DIP-switch functions____________________________________________________________
NET VISION/Box Technical Information ________________________________________________________
Technical Specifications _____________________________________________________________________
Front Panel_______________________________________________________________________________
Rear Panel _______________________________________________________________________________
Description of DIP-switch functions____________________________________________________________
LED Indicators ____________________________________________________________________________
Serial Cable Specification ___________________________________________________________________
11.
67
68
69
70
71
73
CHAPTER 7 - ”HISTORY LOG” MANAGEMENT ____________________________________________ 74
Display of the UPS History Log _______________________________________________________________
Description of the UPS History Log ____________________________________________________________
Description of the UPS Extended Log __________________________________________________________
UPS Log Graphic Display ___________________________________________________________________
Description of the UPS Event Log _____________________________________________________________
Description of the NET VISION Agent Events Log_________________________________________________
10.
50
51
52
53
54
55
57
59
61
64
86
86
87
88
APPENDIX D – REMOTE VIEW _________________________________________________________ 90
What’s Remote View? _______________________________________________________________________ 90
Installation._______________________________________________________________________________ 90
6
Chapter 1
3. CHAPTER 1 – NET VISION OVERVIEW
Functions
NET VISION is an SNMP v1/v3 (Simple Network Management Protocol) and HTTP/HTTPS (Hyper Text
Transfer Protocol) Agent Adapter. It can communicate, send commands and monitor the UPS through the
network. The user can therefore use SNMP managers or Web browsers to manage the UPS through an
Ethernet.
NET VISION also provides an integrated shutdown service for a number of different operating systems. A
shutdown command is sent in any of the following cases: mains failure, low battery, UPS overload, UPS
overheating, imminent shutdown and scheduled shutdown. All shutdown events can be selected by the User.
The integrated shutdown program will automatically perform an orderly shutdown to prevent the damage to
the system hardware and software.
There are two versions of NET VISION available. One is an internal Card version, designed for UPS models
which have the extension board slot where NET VISION can be inserted and connected to the UPS through
the comb contacts (figure 1-1a). The other is an external Box version designed for UPS models which are
not equipped with the extension board slot. A serial cable is used to connect the NET VISION/Box version to
the UPS (figure 1-1b).
NET VISION is fitted with two RS232 ports, one for the UPS and one for configuration via a PC or terminal.
The RS232 ports of the NET VISION are accessed by the RJ45 jacks on the back panel.
Figure 1-1a NET VISION/Card
7
Figure 1-1b NET VISION/Box
Chapter 1
Features
¾
Network connection through RJ45 connector
The RJ45 plug connects the UPS directly to the Ethernet network without occupying the RS232 port
on the computer and without having to install a UPS monitoring program on the computer.
¾
Network UPS management
The UPS can be remote controlled from any computer on the network.
¾
Remote monitoring of the UPS via SNMP v1/v3, HTTP/HTTPS and Java Applets
The UPS can be monitored using a Browser, a Java Applet or an SNMP application.
¾
UPS and NET VISION set up from any computer on the network (access is password protected)
Certain parameters of the UPS and NET VISION can be configured from any SNMP control workstation or via a Browser.
¾
Analysis of the power quality via Java Applets
Java Applets display dynamic graphics to indicate the quality level.
Saving the Events & measurements log in non-volatile memory
A file stored in the internal non-volatile memory contains the log of UPS power events, power quality,
UPS status and battery condition.
¾
Automatic shutdown
The standard software automatically executes the orderly shutdown of the workstations/server in the
event of failure or scheduled shutdown.
¾
Multiple Shutdown of servers/workstations
The standard software will broadcast mains failure messages to all computers connected on the
network mains and will proceed to the automatic shutdown of all computers even if they use different
operating systems.
¾
SNMP Trap and/or Applet Java notification to the system administrator.
In addition to the standard receipt of alarm messages through the shutdown program, notification of
an anomaly or failure can also be sent from Net Vision using SNMP Trap or automatic pop-up messages created by a Java Applet.
8
Chapter 1
System Operation
NET VISION is an interface between UPS and an Ethernet network. NET VISION can obtain the UPS
status and send commands to UPS through its RS232 interface. NET VISION supports SNMP and
HTTP protocols. The SNMP NMS and Web Browsers can monitor the UPS status sending commands
to UPS and can change the NET VISION set-up.
NET VISION also provides shutdown software for various operating systems. The shutdown software
uses a proprietary protocol to automatically connect and communicate with NET VISION through the
network. NET VISION will shutdown in cases of: mains failure, battery low and scheduled shutdown.
The Shutdown software will proceed to the shutdown process in order to prevent the abnormal shutoff
of workstations or servers due to power failure.
Computers
configured via
RS232
UPS
NMS Station or
W eb Browser
RS232
NET VISION
Power line
Ethernet
Shutdown
Program
Shutdown
Program
Shutdown
Program
Computer 1
Computer 2
Computer 3
Operating
System 1
Operating
System 2
Operating
System 3
Figure 1-2 Diagram of NET VISION system operation
9
Chapter 1
Layout of NET VISION Connections
Back panel of NET VISION/Card
Figure 1-3 NET VISION/Card view of back panel
1.
2.
3.
4.
DIP-switches
Reset button
RS232 serial interface port
10/100Base -T Ethernet Connector
Back panel of NET VISION/Box
Figure 1-4 NET VISION/Box view of back panel
1.
2.
3.
4.
5.
6.
10/100Base -T Ethernet Connector
RS232 serial interface port for cable to connect the UPS
RS232 serial interface port for cable to connect a PC or terminal
DIP-switches
Reset button
DC power outlet
10
Chapter 2
4. CHAPTER 2 - NET VISION INSTALLATION
Hardware Installation
Depending on the NET VISION version you are using, refer to the section entitled “NET VISION/Card
Hardware Installation” or to the section entitled “NET VISION/Box Hardware Installation
NET VISION/Card Installation
1. Insert the NET VISION/Card into the UPS slot, see figure 2-1. See also the manual of the specific UPS
for correct installation; (the procedure for card Installation may differ for each model of UPS).
2. Tighten the screws of the NET VISION/Card bracket
Figure 2-1 Installing the NET VISION/Card on the UPS
11
Chapter 2
NET VISION/Box Installation
1. Use the UPS serial cable (marked UPS) to connect the NET VISION/Box port to the serial port of the
UPS (figure 2-2).
2. Connect the NET VISION/Box power supply to the UPS outlet; plug the power cable into the NET
VISION/Box power outlet.
N.B.: An adapter may be required (not supplied) to connect the NET VISION/Box power supply to the
UPS outlet.
Power supply
Serial Cable
Figure 2-2 Installing NET VISION/Box on the UPS
Preparation
A PC or a terminal is required in order to configure NET VISION before it is ready for use. It can be configured in one of two ways:
1. NET VISION Configuration via serial port.
2. NET VISION Configuration via network.
Depending on the type of configuration adopted, please refer to the next section for NET VISION Serial
Port configuration, or go to the section “NET VISION Configuration Via Ethernet” in this chapter.
12
Chapter 2
NET VISION Configuration via serial port
NET VISION/Card hardware preparation
1. Procure a PC (with Windows installed) or a Terminal.
2. Connect a RS232 cable supplied with NET VISION between the NET VISION/Card serial port
(marked PC) and the Computer COM port or terminal TTY port.
3. Set the NET VISION/Card dip-switches to the OFF position (normal mode).
Net Vision Card
seri al port
PC or terminal
serial port
Figure 2-3 Serial cable connection for NET VISION/Card
NET VISION/Box hardware preparation
1.
2.
3.
Procure a PC (with Windows installed) or a Terminal.
Connect a RS232 cable supplied with NET VISION between the NET VISION/Box serial port (marked
PC) and the Computer COM port or terminal TTY port.
Set the NET VISION/Box dip-switches to the OFF position (normal mode).
UPS serial port
PC or terminal
serial port
Figure 2-4 Serial cable Connection for NET VISION/Box
13
Chapter 2
NET VISION Configuration (with Windows)
1. Switch the PC on and click on Start, Programs, Accessories, Communication (if present), Hyper
Terminal (if present) and finally on the Hyper Terminal icon to start the communication program as
shown in figure 2-5.
Figure 2-5 Hyper terminal directory in the Programs/Accessories/Communication group.
2. Enter the name and choose an icon for the connection (figure 2-6).
Figure 2-6 New Hyper Terminal connection.
14
Chapter 2
3. Select direct COM port connection (figure 2-7).
Figure 2-7 Select the port connection.
4. Configure the port parameters - 9600 bps, 8 data bits, no parity, 1 stop bit and no flow control (figure
2-8).
Figure 2-8 Parameters of the connection port.
15
Chapter 2
5. If the NET VISION/Card is used, remove it from the slot and then reinsert it. If NET VISION/Box is
used, press the Reset button. Wait 60 seconds so that NET VISION has time to restart.
6. Press Enter on the PC keyboard.
7. A log-in message will appear on the screen (figure 2-9)
+============================================================================+
|
[ SOCOMEC UPS Net Vision Main menu ]
|
+============================================================================+
Enter Password:
Figure 2-9 NET VISION login menu.
8. Enter the password (the default password is public). The main NET VISION configuration menu
appears on the screen (figure 2-10).
N.B.: Each numbered row identifies a menu that is selected by typing the corresponding number at the
prompt. Each menu may contain submenus or values. Each value can be changed by selecting
the corresponding number and re-typing the desired value at the prompt. If an invalid string is entered, NET VISION will keep the preceding value.
+============================================================================+
|
[ SOCOMEC UPS Net Vision Main menu ]
|
+============================================================================+
1. Net Vision Configuration
2. Access Control Table
3. Trap Receiver Table
4. Reset Configuration To Default
5. Exit
6. Restart Agent
Please Enter Your Choice => 1
+============================================================================+
|
[ SOCOMEC UPS Net Vision Configuration Menu ]
|
+============================================================================+
1. System Group
2. Control Group
3. Parameter Group
4. SMTP Group
5. E-Service Group
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-10 NET VISION configuration menu.
16
Chapter 2
IP Address, Gateway Address, Network Mask and Date/Time (System Group Setting)
1. In the configuration menu, press “1” to modify the IP address, Gateway address and other group parameters. The definitions of these parameters are listed below (figure 2-11). Refer to table 2-1 for configuration examples.
+============================================================================+
|
[ System Group Configuration Menu ]
|
+============================================================================+
SNMP Agent Version : Net Vision v0.70 (SN 1203927005)
Ethernet address
: 00 E0 D8 0C 09 5F
1. Ip Address
: 210.67.192.204
2. Gateway Address
: 210.67.192.254
3. Network Mask
: 255.255.255.0
4. System Date
: 25/11/1999
5. System Time
: 09:49:52
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-11 Setting the NET VISION local network addressing parameters, date and time
No.
1.
2.
3.
4.
5.
Function
IP Address
Gateway Address
Network Mask
System Date
System Time
Description
The NET VISION IP address.
The network default gateway.
The sub-net mask setting.
NET VISION internal Date (dd/mm/yyyy)
NET VISION internal Time (hh:mm:ss)
Example/Remark
210.67.192.204
210.67.192.254
255.255.255.0
17/10/1999
13:10:34
Table 2-1 System Group configuration examples
1. After completing these settings, press “0” to return to the configuration menu.
17
Chapter 2
Login Passwords And Available Protocols (Control Group Setting)
1.
In the configuration menu, press "2" to modify the access password and enable/disable the
available network protocols (Figure 2-12). Refer to table 2-2 for configuration examples.
+============================================================================+
|
[ Control Group Configuration Menu ]
|
+============================================================================+
1. HTTP Login Username
: Net Vision
2. Community Read-Only
: public
3. Community Read/Write : *
4. BOOTP/DHCP Control
: Enabled
5. Telnet Control
: Enabled
6. TFTP Upgrade Control : Disabled
7. HTTP Security Control : Disabled
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-12 Setting the passwords and enabling the network protocols
No.
1.
2.
3.
4.
5.
6.
7.
Function
Description
Example/Remark
HTTP Login Username HTTP access login string,
Net Vision
default is “Net Vision”
Community Read-Only General password for read-only public
access, default is “public”
Community Read/Write Administrator password for read public
and write access, default is
“public”
BOOTP/DHCP Control Enable/disable BOOTP/DHCP Disabled
protocols
Telnet Control
Enable/disable the TELNET
Enabled
protocol
TFTP Upgrade Control Enable/disable the TFTP proto- Enabled
col for firmware upgrades via the
local network
HTTP Security Control Enable login and password
Disabled
request for HTTP access
Table 2-2 Control Group configuration examples
1. After completing these settings, press “0” to return to the configuration menu.
18
Chapter 2
General Information and Poll Rate (Parameter Group Setting)
1. To change the SNMP ID information and the frequency at which UPS data is read, press “3” (Figure
2-13). See table 2.3 for configuration examples.
+============================================================================+
|
[ Parameter Group Configuration Menu ]
|
+============================================================================+
1. sysContact
: SOCOMEC UPS Technical Support
2. sysName
: Net Vision
3. System Location :
4. Poll Rate
: 5
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-13 Setting the identification information and the UPS data read frequency
2. Once the settings are complete, press 0 to return to the configuration menu.
No.
1.
2.
3.
4.
Function
SysContact
SysName
Description
Example/Remark
Reference person
“Mr. Smith”
A name to identify the NET VISION, useful “NET VISION on
if more than one system is present
40kVA”
SystemLocation A name to identify the location of NET “Laboratory II”
VISION, useful if more than one system is
present
Poll Rate
UPS data polling rate (seconds)
5
Digys
Table 2-3 Parameter Group configuration examples
E-Mail Parameters (SMTP Group Setting)
1. In the configuration menu, press "4" to modify the SMTP information (figure 2-14).
+============================================================================+
|
[ SMTP Group Configuration Menu ]
|
+============================================================================+
1. Domain Name Server's Ip Address : 192.16.4.5
2. SMTP Mail Address Server
: mailServer.domain
3. SMTP Mail Account
: emailAccount
4. SMTP Mail Account Passwd
: *
5. E-mail first send delay
: 5
6. E-mail send interval
: 1
7. E-mail Receivers Table
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-14 Setting the SMTP parameters.
19
Chapter 2
No.
1.
2.
3.
Function
Description
Domain Name Server's Ip Address DNS server IP Address (x.y.z.n)
SMTP Mail Address Server
IP Address (x.y.z.n)
or name of the server
SMTP Mail Account
NET VISION mail
account
4.
SMTP Mail Account Passwd
5.
E-mail first send delay
6.
E-mail send interval
7.
E-mail Receivers Table
The account password (if required)
Delay of the first mail
send action
Time before sending
the same mail if the
alarm is fixed
Used to configure the
list of the e-mail
receivers
Example/Remark
192.168.7.225
192.168.7.10 or mailsrv.dm
[email protected]
N.B. On all NET VISION firmware releases prior to 2.04, the
end of the address including @
must be omitted.
Password
0 = send immediately
>0 = send after ‘n’ minutes
0 = send only once
>0 = Send the same mail every
‘n’ hours
See next paragraph
Table 2-4 Setting the e-mail parameters
E-Mail Receivers Table
1. Press "7" on the SMTP Group Configuration menu to modify the e-mail receivers information
(Figure 2-15).
+============================================================================+
| SMTP Complete Address
Description
|
+============================================================================+
[1] [email protected]
user 1
[2]
[3]
[4]
[5]
[6]
[7]
[8]
COMMANDS 1. Modify - Modify an entry of table
2. Reset - Reset an entry to default from table
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-15 Setting the e-mail receivers table
1. Press 1 to change the data on one row. Press 2 to delete all the data in a row.
2. After completing all the settings, press 0 to return to the main menu.
N.B.: an e-mail will be sent to all the addresses in the table to notify users when an alarm occurs.
20
Chapter 2
Access Policies (Access Control Table Setting)
If you wish to have more restrictive NET VISION access criteria than the two general “Community”
passwords for a SNMP Manager Program and / or for HTTP Network Management, you can use the
access control table to set PC’s access authorisations (figure 2-16).
Important: Telnet and Serial Port access is subject to the “Community Read/Write” password.
1.
Press 1 to change the data on one line. Press 2 to delete all the data on one line.
2.
After completing all the settings, press 0 to return to the main menu.
+============================================================================+
|
IP Address
Community String
Access
|
+============================================================================+
[1] 0.0.0.0
*
NotAccess
[2] 0.0.0.0
*
NotAccess
[3] 0.0.0.0
*
NotAccess
[4] 0.0.0.0
*
NotAccess
[5] 0.0.0.0
*
NotAccess
[6] 0.0.0.0
*
NotAccess
[7] 0.0.0.0
*
NotAccess
[8] 0.0.0.0
*
NotAccess
COMMANDS 1. Modify - Modify an entry of table
2. Reset - Reset an entry to default from table
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-16 Access control table
Passwords entered in Community String fields are not masked using RS-232 connection, while if a
Telnet connection is used the passwords are masked by asterisks “ ***** ” which will be displayed instead of typed characters.
If the IP address of a PC is set as “No Access”, the PC in question will not be able to access any NET
VISION information, even if the Community read-only password is recognised.
21
Chapter 2
Trap Receivers Setting
If you want to use a SNMP control workstation to monitor the UPS using NET
VISION, the IP address of the workstation must be specified in the Trap Receiver Table menu, to inform NET VISION which stations are authorised to receive “trap” messages and send commands (security reasons).
1. Press “1” to change the data on a line. Press “2” to delete all the data on a line.
2. After completing these settings, press “0” to return to the configuration menu (figure 2-15).
Note: Trap Receivers Table configuration is only used for SNMP Network management.
+============================================================================+
|
IP Address
Community String
Description
|
+============================================================================+
[1] 0.0.0.0
*
[2] 0.0.0.0
*
[3] 0.0.0.0
*
[4] 0.0.0.0
*
[5] 0.0.0.0
*
[6] 0.0.0.0
*
[7] 0.0.0.0
*
[8] 0.0.0.0
*
1. Modify - Modify an entry of table
2. Reset - Reset an entry to default from table
0. Return to previous menu
Please Enter Your Choice =>
Figure 2-17 Setting Trap Receivers.
End of NET VISION Configuration
After completing all the settings, press “5” to terminate the connection without restarting NET VISION
or “6” to terminate the connection forcing the NET VISION internal program to restart.
The initial NET VISION configuration is now complete.
N.B.: if you want to restore the default NET VISION factory configuration, press “4”: Reset Configuration to
Default.
22
Chapter 2
NET VISION Configuration via Ethernet
Depending on which version you are using, please refer to the section entitled “NET VISION/Card
Hardware Preparation” or to “NET VISION/Box Hardware Preparation.”
NET VISION/Card Hardware Preparation
1. Procure a PC with an Ethernet card and a Web Browser installed.
2. Connect the Ethernet cable (twisted-pair cable) to the PC’s Ethernet card and to a network HUB or
Switch plug.
3. Connect another Ethernet cable (twisted-pair cable) to the NET VISION/Card plug and to a HUB or
Switch plug. (Figure 2-18).
4. Set the NET VISION/Card DIP-switches to OFF.
5. Turn on the UPS and wait 60 seconds for full NET VISION start-up.
Net Vision Card Ethernet
Plug
PC Ethernet card plug
Figure 2-18 PC-NET VISION/Card connection via Ethernet
NET VISION/Box hardware Preparation
1. Procure a PC with an Ethernet card and a Web Browser installed
2. Connect the Ethernet cable (twisted-pair cable) to the PC Ethernet card and to a network HUB or
Switch plug.
3. Connect another Ethernet cable (twisted-pair cable) to the NET VISION/Card plug and to a HUB or
Switch plug. (Figure 2-19).
4. Set the NET VISION/Card DIP-switches to OFF.
5. Press the Reset button and wait60 seconds for full NET VISION start-up.
23
Chapter 2
UPS serial port
Net Vision Box Ethernet
pulg
Twisted pair Ethernet cables
PC Ethernet card plug
Figure 2-19 PC-NET VISION/Box connection via Ethernet
Changing the routing settings on a PC
The first time you use NET VISION, the PC IP address will probably not have the same IP sub-net
mask as the NET VISION.
Use “route add” command to change the routing table on the PC and then configure NET VISION (if
the IP address of the PC has the same IP sub-net mask as the NET VISION, you just need a Web
Browser for the connection).
Procedure to change the routing table for Windows™ operating systems
Follow the same procedure to add a routing path to your PC:
Turn on the PC and set up the TCP/IP protocol, if necessary (refer to the operating system manual for
information on how to configure the TCP/IP protocol.
Find the IP address of your PC by typing “winipcfg” at the MS-DOS prompt for Windows™ operating
systems 9x or Me and, when the IP configuration window appears, select the Ethernet card connected
to the HUB typing “ipconfig.” for Windows™ operating systems NT4.0, 2000 or XP.
Enter the following command to add a routing condition:
Syntax: Route add [NET VISION default IP address] [PC IP]
Example: Route add 192.168.7.18 210.67.192.147
Assuming the PC IP address is 210.67.192.147 and the IP address of NET VISION is
192.168.7.18. (default value)
Note: see your Windows manual for detailed information on how to add a routing condition.
Finding the NET VISION IP address
The NET VISION IP address may not be configured with the default value and so it may be difficult
to find this information manually without using a serial connection.
In this case, you can use the “SUPGRADE2.exe” program which comes with the NET VISION CDROM. The program can easily identify the IP addresses of all the NET VISION systems installed on
the LAN (Local Area Network).
24
Chapter 2
The program can be run from the Upgrade directory of the NET VISION CD.
When the Supgrade window appears, just click on Discover for a list of all the NET VISION systems
connected to your LAN (figure 2-20).
Figure 2-20 Supgrade.exe application program
If the icon next to the NET VISION IP address is blue, there is no need to add a routing condition to
connect up to NET VISION using Telnet or a Web Browser. If, on the other hand, the icon is grey,
then a routing condition must be added to connect up to NET VISION (see the section “Changing the
routing settings on the PC” in this Chapter). .
The Supgrade2.exe program can also be used to update NET VISION firmware with new versions,
as they become available.
N.B.: Supgrade2.exe can be run on Windows™ operating systems.
25
Chapter 2
Running the TELNET Command
1. Run the command dialog box (for Windows this is the MS-DOS prompt).
2. Enter the “192.168.7.18” command and press Enter. The NET VISION IP default address is
192.168.7.18.
3. The NET VISION configuration menu via Telnet is the same as the configuration menu via serial
port, already described in this chapter at point 7 of ”Setting the NET VISION Configuration” paragraph.
N.B.: Telnet access to NET VISION can be disabled using a Telnet connection, so take care not to set
“Disable Telnet Control” if NET VISION cannot be easily connect to a PC serial port to restore the
Telnet Connection.
Running the Web Browser (Netscape, Internet Explorer, etc.)
1. Run the Web Browser.
2. Type the address “http:\\192.168.7.18” (if 192.168.7.18 is the current NET VISION address)
3. Enter “Net Vision” as the user name log-in (make sure that the first letters of the two words are upper
case and that the words are separated by a space) and “public” as the password.
4. The NET VISION home page will appear (figure 2-21).
Figure 2-21 NET VISION Home Page: Comprehensive View.
26
Chapter 2
Initial Configuration Setup
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Select “Net Vision Configuration” on the Net Vision Mgmt main menu to setup the network configuration parameters (figure 2-22).
Enter the NET VISION IP address you want.
Enter the network gateway IP address if needed.
Enter the network sub-net mask if needed.
Select “Set Values” to save the settings (NET VISION will save the configuration).
Select “Set Real Time” to set the appropriate Date and Time values in the specified format.
Click on “Set Values” to save the Date and Time settings.
Select “Net Vision Control” to enable or disable network protocols if needed
(Figure 2-23).
Click on “Apply” to save the changes.
Configuring basic NET VISION parameters via Web Browser
Figure 2-22 NET VISION initial configuration screen.
27
Chapter 2
Enabling/Disabling network protocols and NET VISION Reset
The “Net Vision Control” menu lets you select which communication protocols will be enabled and therefore
used in communications with NET VISION (figure 2-23).
To inhibit the use of one or more protocols on NET VISION, just select the “Disabled” value for each of these
and then confirm the selection by clicking on “Apply”.
The same menu also lets you delete any log data stored in the NET VISION memory by highlighting the
relevant button and then clicking on “Clear”.
Figure 2-23 NET VISION Control screen page.
28
Chapter 3
5. CHAPTER 3 – WEB BROWSER OPERATIONS
It is assumed that the NET VISION connection and basic configuration procedures described in the preceding chapters have already been carried out and that the system is ready to use.
Using a Web Browser to view the NET VISION Home Page
1. Run the Web Browser and enter the address: “http:// 210.67.192.204” if the NET VISION IP address
is 210.67.192.204. (If a different address has been set, then this should be entered).
2. The NET VISION home page appears on the screen.
3. Press “Help” at the bottom of the screen for a brief description of each menu item.
Description of the Menus
UPS Monitor
This menu displays the main measurements and data read from the UPS.
Note.
In case of parallel configuration, measurements and data will not refer to the single UPS but to
the entire system.
Comprehensive View
This page gives a snapshot of all the main UPS parameters as described in figure 3-3. The page is refreshed automatically. To set the refresh interval select the “Net Vision Mgmt” menu – “Homepage Refresh Rate”.
29
Chapter 3
UPS Comprehensive View
Figure 3-3 NET VISION Home Page: Comprehensive View.
you access the graphic mimic panel of the UPS (Java Applet
Selecting the software button
Monitor). See the section entitled Java Applet Monitor for a detailed description.
UPS Identification
Select “UPS Identification” on the “UPS Monitor” menu of the home page to get a table of the UPS
and NET VISION Identification Parameters (figure 3-4).
Figure 3-4 NET VISION UPS Monitor: UPS Identification.
30
Chapter 3
UPS Battery
Select “UPS Battery” in the “UPS Monitor” on the main menu to get a table of the UPS battery parameters (figure 3-5).
Figure 3-5 NET VISION UPS Monitor: UPS Battery Parameters.
The battery status may be one of the following:
Low Battery
Battery failure
Battery discharging
Battery OK
UPS Input
To view the UPS input parameters, select “UPS Input” on the “UPS Monitor” menu (figure 3-6).
Figure 3-6 NET VISION UPS Monitor: UPS Input Parameters
One column will be displayed for single-phase UPS data and three columns for three-phase UPS.
31
Chapter 3
UPS Output
Select “UPS Output” on the “UPS Monitor” main menu to get a table of the UPS output parameters
(figure 3-7).
Figure 3-7 NET VISION UPS Monitor: UPS Output Parameters
One column will be displayed for single-phase UPS data and three columns for three-phase UPS.
Alarm Table
Select “Alarm Table” on the “UPS Monitor menu to get a table of possible alarms (figure 3-8).
Figure 3-8 NET VISION UPS Monitor: Alarm Table
32
Chapter 3
Shutdown Clients Table
Select “Client Table” on the “UPS Monitor” menu for a table of connected clients running the shutdown software (figure 3-9).
Figure 3-9 NET VISION UPS Monitor: Shutdown Clients
Java Applet monitor
in the “UPS Monitor” “Comprehensive view” menu, you acIf you click on the software button
cess the UPS graphic mimic panel (Java Applet Monitor - figure 3-10).
NET VISION provides a real-time Java applet to display the UPS status and log. This applet can display the most important UPS parameters in real time – AC input voltage, AC output voltage, UPS load,
and battery capacity and input frequency in its main window. This applet has function icons (specified
below), a status bar that can display the current UPS status, an alarm box that can display the codes
of the current UPS alarms and a bar indicating the presence of UPS modules in parallel.
Function Icons
Status bar
Figure 3-10 NET VISION UPS: Java Applet Monitor
33
Measurement bar
Chapter 3
Function keys
Display switch
This icon is used to switch the display from measurement
mode to graphic mode and vice versa.
Pop-up switch
Enables/disables the display of warning messages.
Polling interval
The time interval that the display needs to get the next record (defines the update time for data on the screen)
Exit
Exit the Java applet monitor.
Status Bar
Displays the UPS status, changing the colours of the boxes which describe the alarms and conditions.
Measurement Bar
Provides graphic representation of the UPS measurements.
Parallel Modules
This is used to detect the presence of up to six UPS modules in parallel. If a module is found, the corresponding cell is coloured green (the default colour is grey). If a module is configured correctly and is
operating normally, the corresponding cell is green. It becomes red if there is an operating problem.
Active Alarms
This box gives the codes of active alarms on the UPS according to the indications in Table 3 -1.
Whether the alarms shown are managed or not depends on the UPS model; as a result, some alarms
may be displayed on some UPS models, and not on others (see your UPS manual for further information).
34
Chapter 3
Alarm Codes
CODE
A00
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
Description
Alarm present (or of all UPS alarms)
Battery failure/Battery anomaly/Battery fuse open
UPS overload
Output voltage out of tolerance
Digital power supply fault (Vdc)
Input voltage out of tolerance
Auxiliary mains out of tolerance
Inside over-temperature alarm (OR of all temperature sensors)
Manual By-pass closed
Short-circuit detection on UPS output
Battery charger failure
Inverter over-current
Excessive Inverter distortion
Pre-charge voltage out of tolerance
BOOST output voltage too low
BOOST output voltage too high
Battery voltage too high
Environmental alarm
Overload time-out blocking Inverter
Microprocessor control system failure
Configuration data map corrupted
PLL Fault
Input mains general alarm
Rectifier general alarm
BOOST general alarm
Inverter general alarm
Battery charger general alarm
Output voltage over limits
Output voltage under limits
By-pass general alarm
UPS stopped for overload
Imminent Stop
Module 1 in parallel general alarm
Module 2 in parallel general alarm
Module 3 in parallel general alarm
Module 4 in parallel general alarm
Module 5 in parallel general alarm
Module 6 in parallel general alarm
External Alarm 1
External Alarm 2
External Alarm 3
External Alarm 4
E-service general alarm
Redundancy lost
Periodic service check up
Automatic and manual transfer disabled
Automatic transfer disabled
Battery room alarm
Manual bypass alarm
Battery Discharged
Insufficient resources
Optional boards general alarm
Rectifier fault
Boost fault
Inverter fault
Parallel module fault
Gen-set general alarm
Gen-set fault
Emergency stop active
Battery circuit open
Fans failure
Phase rotation fault
A62: UPS Alarm
A63: UPS Alarm
Table 3-1 Alarm Codes
35
Chapter 3
UPS Management
This menu lets you modify the control parameters of the connected UPS using NET VISION.
All the menus are available in read-only for all authorised users, whereas only the administrators have
access in read/write mode.
UPS Configuration
This menu displays the nominal input and output values of the UPS (figure 3-11).
Figure 3-11 NET VISION UPS Configuration screen
UPS Control
This menu lets you send commands to the UPS for immediate execution. It is visible only to read and
write authorised users (administrators) (figure 3-12)
N.B.: The commands will be sent to the UPS immediately without any forewarning message to the connected clients, so they should only be used when absolutely necessary.
36
Chapter 3
Displayed
only if the
UPS has at
least one
power plug
Figure 3-12 NET VISION UPS Control screen
Power Share Management
The UPS may have up to four power share plugs, which are power outlets that can be programmed by
the user (figure 3-13).
This menu lets you configure the power share plugs.
Figure 3-13 Power Share Management screen
37
Chapter 3
Available Plugs:
Lists the Active Plugs. If a plug is not available, the related
row is hidden.
Mode:
None:
Automatic output plug management is disabled.
Battery Capacity (%):
The output power plug will be switched off when the battery
capacity falls below the set value (1 to 99%). This feature is
managed by the UPS.
Remaining backup Time (min):
The output power plug is switched off when the remaining
back up time is lower than the set value (from 1 to 120 minutes). The feature is managed by the UPS.
Emergency Lighting On:
In case of mains failure, the UPS powers the output plugs to
activate the emergency lights. When the power is restored,
the plugs will be switched off (no set value). This feature is
managed by the UPS
Time Since On Battery Power (min):
The output plug is switched off when the time the unit has
been working in battery mode exceeds the set value. This
feature is managed by NET VISION.
Value:
Value used to manage the Power Share output plugs.
Set:
When you click on this icon, NET VISION stores all the settings and sends them to the UPS.
UPS Battery Test
This menu lets you check the battery status and run a battery test, if the UPS has this option (figure
3-14). See the UPS manual for further details.
Figure 3-14 NET VISION UPS Battery Test
Warning: This function is displayed only if the option is available on the UPS connected to NET VISION.
38
Chapter 3
Shutdown Parameters
This menu lets you modify the parameters associated with shutdown events (figure 3- 15).
These events which cause shutdown of the clients and of the UPS are:
¾
¾
¾
¾
¾
¾
AC Failed
Battery Low
UPS Overload
UPS Over Temperature
On Bypass
Imminent Stop
: mains power failure
: low remaining battery charge
: output overload
: UPS internal overheating
: on manual or automatic bypass
: UPS imminent shutdown alarm.
Figure 3-15 NET VISION Shutdown parameters
The following elements are also available, but can only be configured by the NET VISION administrators:
¾
Weekly Schedule:
weekly scheduled start-up/shutdown
¾
Special Day Schedule:
start-up/shutdown on certain days of the year
¾
ECO/MODE Schedule:
activation or deactivation of ECO/MODE
N.B.: These functions will be displayed only if they are available on the UPS connected to NET VISION.
39
Chapter 3
Weekly Schedule
This menu lets you change the start-up and shutdown parameters set for certain days of the week
(figure 3-16).
Figure 3-16 NET VISION Weekly Schedule
Special Schedule
This menu lets you change the start-up and shutdown parameters set for certain days in the year
(figure 3-17).
Figure 3-17 NET VISION Special Schedule
40
Chapter 3
ECO/MODE Schedule
This menu lets you change the parameters for activating or deactivating ECO/MODE (figure 3-18).
Figure 3-18 NET VISION Eco-Mode Schedule
N.B.: the functions described in this chapter are displayed only if they are available on the UPS. Consult the
UPS manual to check whether these options are available.
41
Chapter 3
Net Vision Mgmt
In this menu you can display and modify the NET VISION control parameters.
All the menus are available in read-only for authorised users, while only the administrators have access in read/write mode.
Set Real Time
This menu lets you manually set the NET VISION internal date and time. If the Primary or Secondary
Time Server has been configured, modifying the time parameters may not have effect, as the shutdown program will update the time to that of the computer on which it is run.
NET VISION Configuration
This menu lets the administrator set the local network configuration parameters on NET VISION. The
main settings of the SMTP (sending e-mails) can also be set.
List of parameters that can be set:
¾ Net Vision IP Address:
NET VISION IP address in decimal point format (e.g.
192.0.60.229).
N.B.: changing the NET VISION IP address will cause a soft reboot and while NET VISION is booting
up it cannot be accessed on the network.
¾ Net Vision Gateway Address:
Network Gateway IP address in decimal point format (e.g.
192.9.60.10).
¾ Net Vision Subnet Mask:
NET VISION subnet mask (e.g. 255.255.255.0).
¾
Name of reference person or network administrator.
System Contact:
¾ System Name:
NET VISION ID name, useful if there is more than one system connected on the network.
¾ System Location:
name, which identifies the NET VISION location, useful if
there is, more than one system installed in the building.
¾ Primary Time Server:
Primary Time Server IP address in decimal point format. The
NET VISION date and time are supplied by the Primary
Time Server (i.e. one of the computers on the network that
runs the shutdown program).
¾ Secondary Time Server:
Secondary Time Server IP address in decimal point format.
If the Primary Time Server is not available, the NET VISION
date and time are supplied by the Secondary Time Server.
¾ Domain Name Server's IP:
IP address of the Domain Name Server in decimal point
format.
¾
42
Chapter 3
¾ SMTP Mail Address Server:
name or IP address in decimal format of the mail server
used by NET VISION to send e-mails.
¾ SMTP Mail Account:
user ID to be used by NET VISION to send e-mails.
¾
e-mail first send delay:
The mail will be sent only if the alarm remains active for
longer than the set value (expressed in minutes).
¾
e-mail send interval:
The e-mail will be sent again at the end of the set time interval if the status remains active. The format is expressed in
hours.
¾ History Log Interval (sec):
Configures time interval (in minutes) to save the Input Voltage, Output Voltage, Load and Battery Capacity values in
the History Log. The maximum value for this setting is 28800
(i.e. 8 hours)
¾ Extended History Log Interval (min): Configures the time interval, in minutes, to save the Input
Voltage, Output Voltage, Load and Battery Capacity values
in the extended history log. After each interval the UPS parameters are analysed and the minimum, maximum and average values of these parameters are saved. The parameter
can be set from 1 to 10080 minutes (7 days).
¾ Net Vision Polling Rate (sec):
Configures the time interval that NET VISION must wait to
get data on the current UPS status.
¾ Net Vision Baud Rate (sec):
Data transfer speed.
NET VISION Control
This menu lets you enable or disable the communication protocols available on NET VISION and can
be used to restart the system and/or reset the NET VISION internal parameters.
List of parameters that can be configured:
¾
BOOTP/DCHP Status:
This parameter enables or disables the Boot Protocol
(BOOTP) / Dynamic Host Configuration Protocol (DHCP)
process. These protocols are commonly used on the Internet
to get a dynamic IP address from a server.
¾
Network Upgrade:
This parameter enables or disables the Trivial File Transfer
Protocol (TFTP) Upgrade Control. On Windows™ systems,
supgrade.exe (a program included in the kit) can be used via
TFTP to update the NET VISION firmware.
¾
Telnet Connection:
This parameter enables or disables the “Terminal to Server
Application (Telnet Control process)” for NET VISION configuration.
¾
SNMP TRAP Filter:
This is the parameter enabling or disabling the first four
Traps (Enabled = RFC1628 compliant).
¾
SNMP Support :
Change the SNMP protocol version : disable, SNMPv1,
SNMPv3
¾
Reset Net Vision to Default:
Restores default parameters on NET VISION.
¾
Restart Net Vision:
Restarts NET VISION, loading all parameters that have
been modified.
43
Chapter 3
¾
Clear Log Data:
Deletes selected data in the NET VISION log.
e-Mail Receivers
This menu lets you set up to eight e-mail addresses to which a customer configurable e-mail message
will be sent should any of the selected alarms occur.
If the option All Alarms is selected, an e-mail will be sent if any alarm occurs (figure 3-19).
The Customer Text Field can be used to give more information on the UPS location and type of load
(i.e. Ups located in factory 1, supplying servers).
N.B.: The Set Value command must be used to save any changes and the Send Test command can
be used to check that the system has been configured correctly.
Figure 3-19 e-Mail Receivers
e-Service Configuration
This menu is used for customer service. It must be configured only if an after sales service contract
has been signed.
The customer service will provide instructions as to how this menu must be configured.
SNMPv3 USM Table
SNMPv3 is more secure than the previous versions, SNMPv1 and SNMPv2c. This table uses USM security
model for processing outgoing and incoming messages.
This menu is visible only if the SNMP Support field on Net Vision Control page is set to SNMPv3.
44
Chapter 3
1. Index
The index number of the entries.
2. User Name
The user name of SNMPv3 to be sent. The maximum length of the string is 31 characters. The user
name must be the same as Trap community that lists in the SNMP Trap Receivers Table or user can not
receive the trap by SNMPv3.
3. Auth Password
The Authentication password of SNMPv3. The maximum length of the string is 31 characters.
4. Priv Password
The Privacy password of SNMPv3. The maximum length of the string is 31 characters.
5. Security Level
• noAuthnoPriv: Using this option provides no security, confidentiality, or privacy at all. It might be useful for certain applications such as development and debugging to turn security off.
• authNoPriv: The user at the management application is authenticated by the SNMPv3 entity before
the entity allows the user to access any of the values in the MIB objects on the agent.
• authPriv: The user at the management application is authenticated by the SNMPv3 entity before the
entity allows the user to access any of the values in the MIB objects on the agent. In addition, all of
the requests and responses from the management application to the SNMPv3 entity are encrypted,
so that all the data is completely secure.
6. Authentication
Select authentication protocol, HMAC_MD5 and HMAC_SHA. This value is the message authentication code to be inserted in the msgAuthenticationParameters files of the SNMPv3 message.
7.
•
•
•
User Status
Ready: The status is ready to encode the message.
Processing: The status is trying to encode the message.
Not use: The status is not use.
SNMP Trap Receivers
This table may contain up to eight addresses of the Network Management stations to which the
SNMP Traps will be sent.
¾
Index: the index numbers of the entry.
¾
NMS IP Address: IP address in decimal point format, of the NMS stations to which the traps will be
sent. The Traps will only be sent to receivers whose address is different from 0.0.0.0.
¾
Community String: this is the password which authorises an NMS station to access NET VISION.
The string can have a maximum of 16 characters.
¾
Description: Customer description string.
45
Chapter 3
SNMP/HTTP Access Control
This menu displays a list of addresses (in decimal point format) of the NMS stations and clients PC’s
which may or may not be authorised read/write access to NET VISION.
Important: it is strongly recommended to pay attention if you use the browser to modify these parameters,
because if a “No Access” policy is configured for your PC address, no further access is permitted until a new setting is made using Telnet or Serial Connection.
¾
Index:
index number of the addresses
¾
NMS IP Address:
IP address used to identify the management station or a client computer.
0.0.0.0 means that it has not been configured.
¾
Community:
Password associated to the IP address. It is used to define the type of access.
¾
Access Type:
The access options may be: no access, read only, read and read-write.
Homepage Refresh Rate
This menu lets the administrator set the refresh rate for the NET VISION Web pages (figure 3-20).
N.B.: The recommended minimum refresh rate is 5 seconds.
Figure 3-20 Homepage Refresh rate
UPS History
Please refer to Chapter 7 for information on this menu.
46
Chapter 4
6. CHAPTER 4 - SNMP NMS USER OPERATIONS
NET VISION SNMP Configuration parameters
IP Address, Gateway Address And MIB System Group Setting
Before using NET VISION with SNMP applications, the IP address, Gateway addresses and MIB
System Group must be configured correctly.
See Chapter 2 for further information.
IP Write Access Setting
NET VISION supports the SNMP protocol. A PC with an “SNMP Manager” program can be used to
control the UPS via the net.
In order to comply with NET VISION safety directives, the IP address of the PC normally used for the
management, must be added to the write access table on NET VISION. See the “Access Control
Table Settings” in Chapter 2 for further details.
N.B.: if the IP address of the PC is not added to the NET VISION write access setting table, the
SNMP application will only be able to read the UPS status and cannot send any commands to the
UPS.
Trap Receivers Setting
If you want to enable the ‘trap’ function you must add the IP address of the computer used as the
SNMP station in the NET VISION trap receivers table. See Chapter 2, “Trap Receivers Setting ” section for more details.
SNMP Management Software Set Up
Add the NET VISION MIB file to the SNMP management program database.
To access the NET VISION SNMP agent, use the read only “GET community string” or the read/write
“SET community string” passwords. The public password can be changed by the system administrator
if necessary (see the Trap Receivers Setting paragraph in this chapter).
GET Community string: public (default)
SET Community string: public (default)
Note: if you have set a different password for “Community Read-only, Community Read/Write” during a
previous NET VISION configuration on the “Net Vision Configuration, Control Group” menu, then you
have to use these passwords to access the NET VISION. For further information, refer to the MIB file
on the NET VISION CD.
NET VISION and SNMP
47
Chapter 4
The NetVision MIB file can be compiled using an SNMP program.
This MIB file includes the standard “Object Identifiers” and the standard Traps contained in the
RFC1628 specifications, together with some additional “Object Identifiers”.
The following 23 Traps are specifically connected to the UPS:
upsTrapOnBattery
upsTrapTestCompleted
upsTrapAlarmEntryAdded
upsTrapAlarmEntryRemoved
upsTrapUpsNormal
upsTrapUpsBattTestFailed
upsTrapOnBatteryPower
upsTrapBatteryLow
upsTrapPowerRestored
upsTrapImminentStop
upsTrapTurnedOff
upsTrapOverTemperature
upsTrapOverload
upsTrapOnMains
upsTrapRedoundancyLost
upsTrapEmdTempLow
upsTrapEmdTempHigh
upsTrapEmdHumidityLow
upsTrapEmdHumidityHigh
UpsTrapEmdFirstInputActive
UpsTrapEmdFirstInputRestored
UpsTrapEmdSecondInputActive
UpsTrapEmdSecondInputRestored
Description:
"upsTrapOnBattery" gives information on battery operation, how long the system has been working
in battery mode and the estimated remaining back up time.
"upsTrapTestCompleted" not used
to find out if the UPS has any alarms, refer to the "upsTrapAlarmEntryAdded” and "upsTrapAlarmEntryRemoved" trap functions.
48
Chapter 4
Traps have the following format:
iso(1)
org(3)
dod(6)
internet(1)
private(4)
enterprises(1)
socomecSicon(enterprises 4555)
software(socomecSicon 1)
network(software 1)
netvision(network 1)
upsObjects(netvision 1)
upsTraps(netvision 2)
upsIdent OBJECT IDENTIFIER ::= { upsObjects 1 }
upsBattery
OBJECT IDENTIFIER ::= { upsObjects 2 }
upsInput OBJECT IDENTIFIER ::= { upsObjects 3 }
upsOutput
OBJECT IDENTIFIER ::= { upsObjects 4 }
upsBypass
OBJECT IDENTIFIER ::= { upsObjects 5 }
upsAlarm OBJECT IDENTIFIER ::= { upsObjects 6 }
=======================<<<<<
upsTest OBJECT IDENTIFIER ::= { upsObjects 7 }
upsControl
OBJECT IDENTIFIER ::= { upsObjects 8 }
upsConfig
OBJECT IDENTIFIER ::= { upsObjects 9 }
upsAgent OBJECT IDENTIFIER ::= { upsObjects 10 }
An example of a real alarm (Trap) is given below:
Trap received @ 10:47:21 AM from host (172.17.16.51)
1.3.6.1.4.1.4555.1.1.1.1.6.2.1.1.17 [OID] = 17 [VALUE]
upsAlarmId.17 [NAME]
1.3.6.1.4.1.4555.1.1.1.1.6.2.1.2.17 [OID] = 1.3.6.1.4.1.4555.1.1.1.1.6.3.8 [VALUE]
upsAlarmDescr.17 [NAME]
==================================
This means that this Trap was sent by the host at IP address "172.17.16.51" at 10:47:21 AM .
The first part indicates the type of Trap: "1.3.6.1.4.1.4555.1.1.1.1.6.2.1.1.17"
(in this case, it is an alarm) and other details refer to Trap ".2.1.1.17"
".2”: upsAlarmTable
“. 1”: upsAlarmEntry
“. 1”: upsAlarmId
“. 17”: upsAlarmId [VALUE]
this means that 17 is the UPS alarm code value
the second part of the Trap "1.3.6.1.4.1.4555.1.1.1.1.6.2.1.2.17:, indicates which alarm has occurred:
"1.3.6.1.4.1.4555.1.1.1.1.6.3.8 [VALUE]"
therefore
"1.3.6.1.4.1.4555.1.1.1.1.6" refers to the Trap, and
".3" : upsWellKnownAlarms
".8" : "the output load exceeds the maximum UPS load."
The Trap means that this is the 17th transmission since the NET VISION was switched on and the alarm
refers to the output load which exceeds the maximum load capacity of the UPS.
49
Chapter 5
7. CHAPTER 5 - SHUTDOWN SOFTWARE
The shutdown software is a very important part of the NET VISION system. This
software runs as a service or daemon on servers and/or workstations. It connects to
NET VISION when servers and/or hosts start-up and communicates with NET VISION to alert and if necessary to shutdown servers and/or hosts if UPS alarms occur.
NET VISION scans the status of the UPS, and sends a shutdown command to the
shutdown software when certain events (e.g. AC power failure, Low Battery …) are
detected. The shutdown software will post warning messages on the screen of servers and/or workstations and then, if the user takes no action, will automatically shut
them down.
Supported Operating Systems
Microsoft
1. Windows 95
2. Windows 98
3. Windows ME
4. Windows NT 4.0 (IA32Architecture)
5. Windows 2000 (IA32Architecture)
6. Windows Xp (IA32Architecture)
Or later versions.
Novell
1. Netware 4.x
SCO
1. Unixware 7.1x (IA32Architecture)
2. Open Server 5.x (IA32Architecture)
SUN
1. Solaris 2.6 or later versions (IA32 Architecture)
Linux
1. Linux Kernel 2.2.x or later versions, Red Hat compatible (IA32Architecture)
50
Chapter 5
Using Shutdown Software On Windows
Shutdown Software Installation On Windows 95/ 98/ NT/ ME/ 2000
1. Insert the program CD into the CD reader drive.
2. Run the program “NetVision_X_X_XXXX.exe” on the NET VISION CD (e.g. “D:\shutdown\windows”,
where X_X_XXXX is the shutdown software version and D: is the name of the CD drive)
3. A standard installation window will be executed, where the user must insert the directory in which the
shutdown software will be installed with some personal details.
4. When the installation is complete, the shutdown software is automatically started and a new icon will
appear in the “System Tray” (see figure 5.1).
Figure 5-1 NET VISION Icon
5. Click on this icon with the right button of the mouse and a configuration/service menu will appear
(figure 5.2).
Figure 5-2 NET VISION Shutdown software configuration menu.
6. The configuration menu lets you open a dialog box in which you must enter the NET VISION IP address, the name of the local PC, the delay time for shutdown and the complete file batch or executable file path (these files will be run before the shutdown process is executed (figure 5-3)).
N.B.: the computer shutdown time must be less than the UPS shutdown on NET VISION. .
7. If UPS is connected in parallel, redundancy values can be set (default value is non-redundant).
8. Click on “OK” to confirm the settings.
51
Chapter 5
Figure 5-3 The configuration screen
9. When all the settings are complete, the shutdown program will automatically connect to NET VISION
and connection established status message appears on the screen (figure 5-4).
Figure 5-4 Shutdown program connected to NET VISION
View connected devices using a Web Browser
1. Run the Web Browser on any computer connected to the LAN (Local Area Network).
2. Enter the NET VISION IP address (e.g. http://210.67.192.204).
3. Enter the user login and the password, if required (the administrator can set NET VISION so that the
actions described in step 3 are not necessary).
4. Select “Client Table” from the “UPS Monitor” on the “Net Vision Main Menu”.
5. A list of the connected shutdown programs is displayed on the screen (figure 5-5).
52
Chapter 5
Figure 5-5 NET VISION connected device list
View the connected devices using SNMP NMS
1.
2.
3.
4.
Run the SNMP management program
Load the MIB definition file from the NET VISION CD
Select “upsConnections / upsConnectionTable” from the SNMP management program
The table of connected devices will appear on the screen.
Shutdown on Windows 95/ 98/ NT/ ME/ 2000/ Xp
When NET VISION detects an event, for example, an UPS AC power failure, it will send (depending
on how it has been programmed) the shutdown command to the computers (servers and/or clients).
After the shutdown software receives the command from NET VISION, it will post a dialog box to notify
the user that the system will be shutdown (figure 5-6).
The user can select "Shutdown Now" to start the shutdown procedure or "Cancel" to cancel it. The
shutdown software will proceed with the shutdown and the clients and/or servers will be shut down
automatically if no command is given within the time indicated in the message.
Figure 5-6 Warning message of imminent shutdown
53
Chapter 5
There are five shutdown states that are indicated in the “tray icon”:
Figure 5-7 Possible NET VISION states
Green
Grey and Blue
Red
Barred Green
Yellow
(NORMAL):
(SEEK):
(SHUT):
(SUSP):
(SLPT):
UPS Connection OK.
Trying to locate UPS.
Local machine is about to shut down.
The service is suspended.
Remote UPS is about to shut down or has shutdown.
Uninstalling Shutdown Software
To uninstall the shutdown software, the following procedure should be followed.
1.
2.
3.
4.
Click with the right mouse button on the NET VISION icon in the tray bar.
Select "Exit ” in the menu to stop the shutdown service.
Select "Add/Remove programs" icon in the Windows control panel.
Select "Net Vision ", then click the "Add/ Remove" icon to remove the software.
54
Chapter 5
Using shutdown software on Novell NetWare
Installing shutdown software on Novell NetWare (4.x)
N.B.: the shutdown software can be installed on NetWare 5.x operating systems, but this could
cause CPU overloads.
Contact the customer support service for information on how to run the shutdown on NetWare
5.x or later versions, and for a description of the JSC optional software.
The NET VISION shutdown service for Novell NetWare can be installed on Novell V4.x.
As service uses TCP/IP protocol for information exchange, the user must configure this protocol and
ensure that it works correctly before installing the shutdown software.
Installation
1. Create a new subdirectory for the shutdown software modules in the Novell NetWare system directory.
2. Copy the Novell NetWare shutdown software file “SICSHUT.NLM” and ”UPSCFG:INI” into the newly
created directory.
N.B. : Steps 1 and 2 can be run both on a remote computer connected to the network and on the local server in DOS mode.
3. If you are in DOS mode, start the Novell server.
4. Load the installation module.
LOAD INSTALL
5. select “NCF file options”.
Figure 5-8 Configuring the shutdown execution after server startup.
55
Chapter 5
Figure 5-8b Configuring automatic execution of shutdown after server start-up.
6. Select the “Edit AUTOEXEC.NCF” file (figure 5-8b).
7. Add the following row:
load [Drive]:\(netware_sys_directory)\(shutdown_service_directory)\sicshut.nlm
where: netware_sys_directory is the system directory on the server and
shutdown_service_directory is the directory containing the shutdown software modules.
8. Save the “AUTOEXEC.NCF” file (figure 5-8c).
Figure 5-8c Configuring automatic execution of shutdown after server start-up
9. Restart the NetWare server and the shutdown service will start automatically. Set the shutdown parameters. From this point the shutdown service will protect the system. .
Uninstallation
You only have to uninstall the SICSHUT.NLM and UPSCFG:INI files and if the AUTOEXEC.NCF file
has been modified, it must be restored to its initial status deleting the line which loads the SICSHUT.NLM module.
56
Chapter 5
Using shutdown software on Sco UnixWare
1.
2.
3.
4.
Log onto the SCO UnixWare workstation/server as the supervisor.
Insert the NET VISION CD in the CD drive
If you have already mounted the CD, go to step 5
Mount the CD into directory “/mnt” , specifying system file dosfs. .
# mount –F dosfs /dev/cdrom /mnt
5. Copy the shutdown software into a temporary directory and extract the file from the /uGuard directory
# mkdir /uGuard
# cp /mnt/shutdown/sco_uw/ ug1_0_1038_unixware.tar.Z /uGuard/uGuard.tar.Z
# cd /uGuard
# uncompress uGuard.tar.Z
# tar xvf uGuard.tar
# cd ug1_0_1038
6. Type “./install.sh” to proceed with the installation procedure.
# ./install.sh
The shell command will invoke the 'vi uGuard.conf'. The user must modify the remote host value:
(one or more NET VISION systems to which the shut down device is connected), the host name:
(the name of the local PC which appears in the NET Vision connections table), and the local delay
(delay in the local computer shutdown) The delay can be configured differently for each computer
on which the shutdown software has been installed (figure 5-9). After saving the file, the installation
is complete.
;Sample configuration file of uGuard
;RemoteHost[1/6]: The IP address of remote UPSs.
;Set the address to 0.0.0.0 if no Net Vision is connected.
RemoteHost1 = 192.168.60.11
RemoteHost2 = 0.0.0.0
RemoteHost3 = 0.0.0.0
RemoteHost4 = 0.0.0.0
RemoteHost5 = 0.0.0.0
RemoteHost6 = 0.0.0.0
;Parallel Mode:
;1 = Redundant; 2 = Not redundant(default)
ParallelMode = 2
; HostName: The name of the this machine[optional].
;
Free form for this parameter.
;
Maximum 27 bytes long.
HostName = Mainserver
;LocalDelay: The local delay time before shutdown.
;
Range from 0 to 65536 seconds.
LocalDelay = 120
;Special shutdown program
shutdown = /usr/foo
;Editor user specialized
EDITOR = vi
:
Figure 5-9 uGuard configuration screen
57
Chapter 5
Description of the uGuard parameters
Type the following command to view the list of parameters accepted by uGuard:
# cd /uGuard
# uGuard -h
uGuard -- Net Vision Service, Formal Release 1.0.1038 (Build 2000)
Copyright (C) 1999-2000 SOCOMEC UPS
All rights reserved
Usage : uGuard [-h][-v][-sS][-uU][-d][-r][-p][-l][-e][-gn]
-h : This manual page .
-v : Show revision information.
-s : Start the program now.
-S : Start the program at next boot up time.
-u : Unload program.
-U : Unload program, don't restart at next boot time.
-d : Suspend program.
-r : Resume program.
-p : Probe the status.
-l : List configurations.
-e : Modify configurations.
-gn : Log level(Default = 1;log file is /usr/adm/ugnet.log).
n = 0, No log activities .
n = 1, Log start/stop/warning activities.
n = 2, Log all activities(debug purpose).
Figure 5-10 uGuard -h command
Uninstallation of uGuard
Stop uGuard
#cd /etc
#uGuard -U
Remove uGuard files
#cd /etc
#rm uGuard
#rm uGuard.conf
#cd /etc/rc.d/init.d
#rm ug_usha.sh
#rm /usr/adm/ugnet.log
58
Chapter 5
Using the shutdown software on Sco OpenServer
1.
2.
3.
4.
5.
6.
7.
Log onto the SCO Open Server workstation/server as a supervisor.
Insert the NET VISION CD into the CD drive.
If you have already mounted the CD, go to step 7.
Type "scoadmin" .
Select "Filesystems" -> "Filesystem Manager" -> "Mount" -> "Add Mount Configuration" -> "Local".
Select a "Device File" and insert "Mount Point" name (i.e. : /mnt). Then confirm with "OK".
Copy the shutdown software files into a temporary directory and extract the programs to the /uGuard
directory.
# mkdir /uGuard
# cp /mnt/shutdown/sco_os/ ug1_0_1038_openserver.tar.Z /uGuard/uGuard.tar.Z
# cd /uGuard
# uncompress uGuard.tar.Z
# tar xvf uGuard.tar
# cd ug1_0_1038
8. Type “./install.sh” to proceed with the installation procedure.
# ./install.sh
The shell command will invoke the 'vi uGuard.conf'. The user must modify the remote host value:
(one or more NET VISION systems to which the shut down device is connected), the host name:
(the name of the local PC which appears in the NET Vision connections table), and the local delay
(delay in the local computer shutdown) The delay can be configured differently for each computer
on which the shutdown software has been installed (figure 5-11). After saving the file, the installation is complete.
;Sample configuration file of uGuard
;RemoteHost[1/6]: The IP address of remote UPSs.
;Set the address to 0.0.0.0 if no Net Vision is connected.
RemoteHost1 = 192.168.60.11
RemoteHost2 = 0.0.0.0
RemoteHost3 = 0.0.0.0
RemoteHost4 = 0.0.0.0
RemoteHost5 = 0.0.0.0
RemoteHost6 = 0.0.0.0
;Parallel Mode:
;1 = Redundant; 2 = Not redundant(default)
ParallelMode = 2
;HostName:The name of this machine[optional].
;
Free form for this parameter.
;
Maximum 27 bytes long.
HostName = Mainserver
;LocalDelay: The local delay time before shutdown.
;
Range from 0 to 65536 seconds.
LocalDelay = 120
;Special shutdown program
shutdown = /usr/foo
;Editor user specialized
EDITOR = vi
:
Figure 5-11 uGuard configuration screen
59
Chapter 5
Description of uGuard parameters
Type the following command to view the list of parameters accepted by uGuard:
# cd /uGuard
# uGuard -h
uGuard -- Net Vision Service, Formal Release 1.0.1038 (Build 2000)
Copyright (C) 1999-2000 SOCOMEC UPS
All rights reserved
Usage : uGuard [-h][-v][-sS][-uU][-d][-r][-p][-l][-e][-gn]
-h : This manual page .
-v : Show revision information.
-s : Start the program now.
-S : Start the program at next boot up time.
-u : Unload program.
-U : Unload program, don't restart at next boot time.
-d : Suspend program.
-r : Resume program.
-p : Probe the status.
-l : List configurations.
-e : Modify configurations.
-gn : Log level(Default = 1;log file is /usr/adm/ugnet.log).
n = 0, No log activities .
n = 1, Log start/stop/warning activities.
n = 2, Log all activities(debug purpose).
Figure 5-12 uGuard -h command
Uninstalling uGuard
Stop uGuard
#cd /etc
#uGuard -U
Remove uGuard files
#cd /etc
#rm uGuard
#rm uGuard.conf
#cd /etc/rc.d/init.d
#rm ug_usha.sh
#rm /usr/adm/ugnet.log
60
Chapter 5
Using shutdown software on Sun Solaris
Installing the shutdown software on Sun Solaris 2.6 (or later versions)
N.B. : the shutdown software is specific for IA32 platforms and as such no attempt must be made to
install it on Sparc platforms, as this could result in system malfunction or the total failure of the
operating system.
The shutdown program included on the NET VISION CD can be installed on the SUN Solaris x86
operating systems with versions later than 2.6x up to 8x.
Follow the procedure described below to run the shutdown program correctly:
1.
2.
3.
4.
Log onto the Solaris workstation/server as the supervisor.
Insert the NET VISION CD into the CD drive.
If you have already mounted the CD as a DOS system file, go to step 5.
As Solaris has a “Removable Media Manager”, and only supports ufs system files, this service must
first be deactivated and then the CD should be manually mounted as a DOS system file.
#ps –ef |grep vol (this will display the vold and stdvolcheck process ID)
root
root
xxx
xxx
1 0 08:25:54 ? 0:00 /usr/sbin/vold
1 0 08:27:17 ? 0:00 /bin/ksh /usr/dt/bin/stdvolcheck
5. Stop the ID processes of “vold” and “stdvolch”
#kill xxx (xxx depends on which vold ID you system displays)
#kill xxx (xxx depends on which stdvolcheck ID your system displays)
6. Type mount –F hsfs /dev/dsk/c1t0d0s0 /mnt (CD-ROM on IDE secondary master channel)
7. Move to the mounting directory.
(e.g. : # cd /mnt/shutdown/solaris).
8. Copy the shutdown program to the directory and extract the programs to the /uGuard directory.
# mkdir /uGuard
# cp /mnt/shutdown/solaris/ ug1_0_1038_sunos.tar.Z /uGuard/uGuard.tar.Z
# cd /uGuard
#uncompress uGuard.tar.Z
# tar xvf uGuard.tar
# cd ug1_0_1038
9. Type “./install.sh” to proceed with the installation procedure.
# ./install.sh
61
Chapter 5
The shell command will invoke the 'vi uGuard.conf'. The user must modify the remote host value:
(one or more NET VISION systems to which the shut down device is connected), the host name:
(the name of the local PC which appears in the NET Vision connections table), and the local delay
(delay in the local computer shutdown) The delay can be configured differently for each computer
on which the shutdown software has been installed (figure 5-11). After saving the file, the installation is complete.
;Sample configuration file of uGuard
;RemoteHost[1/6]: The IP address of remote UPSs.
;Set the address to 0.0.0.0 if no Net Vision is connected.
RemoteHost1 = 192.168.60.11
RemoteHost2 = 0.0.0.0
RemoteHost3 = 0.0.0.0
RemoteHost4 = 0.0.0.0
RemoteHost5 = 0.0.0.0
RemoteHost6 = 0.0.0.0
;Parallel Mode:
;1 = Redundant; 2 = Not redundant(default)
ParallelMode = 2
;HostName:The name of this machine[optional].
;
Free form for this parameter.
;
Maximum 27 bytes long.
HostName = Mainserver
;LocalDelay: The local delay time before shutdown.
;
Range from 0 to 65536 seconds.
LocalDelay = 120
;Special shutdown program
shutdown = /usr/foo
;Editor user specialized
EDITOR = vi
:
Figure 5-13 Changing the uGuard settings
Description of uGuard parameters
Type the following command to view the list of the parameters accepted by uGuard:
# cd /uGuard
# uGuard -h
62
Chapter 5
uGuard -- Net Vision Service, Formal Release 1.0.1038 (Build 2000)
Copyright (C) 1999-2000 SOCOMEC UPS
All rights reserved
Usage : uGuard [-h][-v][-sS][-uU][-d][-r][-p][-l][-e][-gn]
-h : This manual page .
-v : Show revision information.
-s : Start the program now.
-S : Start the program at next boot up time.
-u : Unload program.
-U : Unload program, don't restart at next boot time.
-d : Suspend program.
-r : Resume program.
-p : Probe the status.
-l : List configurations.
-e : Modify configurations.
-gn : Log level(Default = 1;log file is /usr/adm/ugnet.log).
n = 0, No log activities .
n = 1, Log start/stop/warning activities.
n = 2, Log all activities(debug purpose).
Figure 5-14 uGuard -h command
Uninstallation of uGuard
Stop uGuard
#cd /etc
#uGuard -U
Remove the uGuard files
#cd /etc
#rm uGuard
#rm uGuard.conf
#cd /etc/rc.d/init.d
#rm ug_usha.sh
#rm /usr/adm/ugnet.log
63
Chapter 5
Using the shutdown software on Linux
The shutdown program included in the NET VISION CD can be installed on Linux operating systems
with Kernel version 2.2.x. or later versions. Follow the procedure described below to run the shutdown program correctly
1. Log onto the Linux workstation/server as the supervisor.
2. Insert the NET VISION CD into the CD drive.
3. If you have already mounted the CD, go to step 5.
Type: mount /dev/cdrom
4. go to the Linux directory on the CD
(ex. : # cd /mnt/cdrom/shutdown/linux).
5. Copy the program files into a temporary directory and extract the programs to a new directory.
# mkdir /uGuard
# cp /mnt/shutdown/linux/ug1_0_1038_linux.tgz /uGuard/uGuard.tgz
# cd /uGuard
# tar zxvf uGuard.tgz
# cd ug1_0_1038
Type “./install.sh” to proceed with the installation procedure.
/install.sh
The shell command will invoke the 'vi uGuard.conf'. The user must modify the remote host value:
(one or more NET VISION systems to which the shut down device is connected), the host name:
(the name of the local PC which appears in the NET Vision connections table), and the local delay
(delay in the local computer shutdown) The delay can be configured differently for each computer
on which the shutdown software has been installed (figure 5-9). After saving the file, the installation
is complete.
;Sample configuration file of uGuard
;RemoteHost[1/6]: The IP address of remote UPSs.
;Set the address to 0.0.0.0 if no Net Vision is connected.
RemoteHost1 = 192.168.60.11
RemoteHost2 = 0.0.0.0
RemoteHost3 = 0.0.0.0
RemoteHost4 = 0.0.0.0
RemoteHost5 = 0.0.0.0
RemoteHost6 = 0.0.0.0
;Parallel Mode:
;1 = Redundant; 2 = Not redundant(default)
ParallelMode = 2
;HostName:The name of this machine[optional].
;
Free form for this parameter.
;
Maximum 27 bytes long.
HostName = Mainserver
;LocalDelay: The local delay time before shutdown.
;
Range from 0 to 65536 seconds.
LocalDelay = 120
;Special shutdown program
shutdown = /usr/foo
;Editor user specialized
EDITOR = vi
:
Figure 5-15 uGuard Configuration screen
64
Chapter 5
Description of uGuard parameters
Type the following command to view the list of parameters accepted by uGuard:
# cd /uGuard
# uGuard -h
uGuard -- Net Vision Service, Formal Release 1.0.1038 (Build 2000)
Copyright (C) 1999-2000 SOCOMEC UPS
All rights reserved
Usage : uGuard [-h][-v][-sS][-uU][-d][-r][-p][-l][-e][-gn]
-h : This manual page .
-v : Show revision information.
-s : Start the program now.
-S : Start the program at next boot up time.
-u : Unload program.
-U : Unload program, don't restart at next boot time.
-d : Suspend program.
-r : Resume program.
-p : Probe the status.
-l : List configurations.
-e : Modify configurations.
-gn : Log level(Default = 1;log file is /usr/adm/ugnet.log).
n = 0, No log activities .
n = 1, Log start/stop/warning activities.
n = 2, Log all activities(debug purpose).
Figure 5-16 uGuard-h command screen.
65
Chapter 5
Uninstalling uGuard
Stop uGuard
#cd /etc
#uGuard -U
Remove the uGuard files
#cd /etc
#rm uGuard
#rm uGuard.conf
#cd /etc/rc.d/init.d
#rm ug_usha.sh
#rm /usr/adm/ugnet.log
66
Chapter 6
8. CHAPTER 6: UPS POWER CRISIS MANAGEMENT
Monitoring the power supply of the load applied to the UPS requires connection to NET VISION in
“Super-User” mode. The “Super-User” mode can be activated from any Web Browser menu that includes this option and in particular from the “Net Vision Mgmt” – “Net Vision Control” menu, simply by
clicking on “Become Super User”:
Figure 6-1 “Become a Super User” command button
You will be asked to enter your user name and password to activate the mode.
UPS Management
NET VISION supports the “UPS Shutdown” or “UPS Stand-by” functions, where “Shutdown” or
“Stand-by“ are two UPS conditions which both result in disconnecting the power supply from the outlet connector.
The following parameters are related to the UPS Shutdown function:
No.
Parameter name
1
UPS Shutdown Delay It defines how many sec- UPS Management – shutdown
(sec)
onds after beginning the parameters
shutdown procedure the
UPS will turn off (min. 0
minutes, max. 65535 minutes).
UPS Shut Off (Enable It defines if the UPS load
UPS Management – shutdown
or Disable)
will be turned off (Stand-by) parameters
after completion of the
server shutdown procedure
2
Description
Web Reference Menu
Table 6-1 UPS shutdown parameters
67
Chapter 6
UPS Control Menu
In “Super-User” mode you can access the “UPS Management” – “UPS Control” menu:
Figure 6-2 UPS Control Menu
This menu enables commands to be sent directly to the UPS as follows:
1. By selecting the software button “UPS Stand-by ON” with the mouse and clicking on the “Send”
button, the UPS load will be powered down immediately. This function, to be used only in emergencies, is not supported on certain UPS models or requires special UPS configuration in order to
be supported. For further information, see your UPS manual or the UPS interface adapter manual.
2. By selecting the software button “UPS Stand-by OFF” with the mouse and clicking on the “Send”
button, the UPS is no longer in Stand-by and the load is powered again. This function is not supported on certain UPS models or requires a special UPS configuration in order to be supported.
For further information, see your UPS manual or the UPS interface adapter manual.
3. By selecting the software button “UPS Eco Mode ON” with the mouse and clicking on the “Send”
button, the UPS switches over to energy saving mode. This function is not supported on certain
UPS models. For further information, see your UPS manual.
4.
By selecting the software button “UPS Eco Mode OFF” with the mouse and clicking on the “Send”
button, the UPS energy saving mode is disabled. This function is not supported on certain UPS
models; for further information, see your UPS manual.
68
Chapter 6
5. By selecting the software button “UPS Alarm Reset” with the mouse and clicking on the “Send”
button, all Alarms are reset.
6. By selecting the software button “UPS Commands Reset” with the mouse and clicking on the
“Send” button, all pending commands are reset.
7. By selecting the software button “UPS Buzzer OFF” with the mouse and clicking on the “Send”
button, the UPS acoustic buzzer is disabled (it will be reactivated when the next alarm occurs).
Forcing UPS To Stand-By
1. Become “Super-User” .
2. Select “UPS Control” from the “UPS Management” of the main menu.
3. Choose “UPS Stand-by on” from the menu.
4. Select “Send” to confirm the above operation.
Stand-by Commando On
UPS output (on)
UPS output off
Switch UPS output off
Figure 6-3 Forcing UPS to stand-by
69
Chapter 6
Programming The UPS Shutdown Schedule
NET VISION supports two types of scheduled shutdowns – (1) weekly schedule; (2) special day
schedule.
1. Select “Shutdown Parameters” from “UPS Management” on the main menu, select “Become SuperUser” and enter your user name and password.
2. Enable “Weekly Schedule” and “UPS Shut Off” if needed.
3. Set the “UPS Shutdown Delay”, “Delay” and warning intervals.
4. Select “Weekly Schedule” from “UPS Management” on the main menu to program the weekly
schedule for UPS shutdown and restart.
5. Select “Special Day Schedule” from “UPS Control” on the main menu to program the special day
schedule for UPS shutdown and restart.
6. Select “Set Value” to confirm all the changes.
N.B.: before you program the shutdown schedules, set the date and time on the “Date and Time parameters” menu on “Net Vision Mgmt” - “Set Real Time” or set the system to read these values
from a “time server”, i.e. a computer used as a clock (see Chapter 3 NET VISION Management).
Example: an example of the UPS output states for the following parameters:
Shutdown time 19:15
Restart time 19:30
UPS shutdown delay = 120 sec
First warning = 60 sec
Warning intervals = 60 sec
Delay for system shutdown = 60 sec.
Shutdown phases
UPS on
Warning messages
UPS shutdown delay
UPS output off
UPS output on
Time
19:10
19:15
19:17
19:30
19:11
19:12
Shutdown begins
UPS output
off
UPS
output
o
n
Duration
120 sec
Defined by user
1st warning
Program
action
2nd warning
Shutdown begins
p
q
r
Figure 6-4 UPS shutdown schedule
70
Chapter 6
No.
1
Parameter
Delay
2
UPS Shutdown
Delay
3
4
5
Description
Interval in minutes before the time set
for scheduled shutdown. During this
interval, warning messages will appear
on the screen of the connected device
(server or workstation).
Defines how many seconds after the
beginning of the shutdown procedure
the UPS will be powered down.
Reference Menu
UPS Control – Shutdown
parameters
UPS Management – Shutdown parameters
UPS Control- Shutdown
parameters
UPS Management – Shutdown parameters
1st warning
Delay for the first warning message
UPS Control – Shutdown
displayed on the screen of the conparameters
nected device (server or workstation). UPS Management – Shutdown Parameters
Warning intervals Intervals between subsequent warning UPS Control – Shutdown
messages displayed on the screen of parameters
the connected device (server or work- UPS Management – Shutstation).
down Parameters
System Shutdown Delay in receiving the shutdown com- Shutdown program
delay
mand to power down the system.
(see relevant Chapter)
Table 6-2 Parameters for programming UPS shutdown
Programming UPS shutdown events
NET VISION supports four types of shutdown events – (1) AC Failed, (2) Battery Low, (3) UPS
Overload, (4) UPS Over Temperature.
1. Select “Shutdown Parameters” from “UPS Management” on the main menu and select “Become
Super-User”; enter your user name and password.
2. Enable the necessary shutdown events from among the following: AC Failed, Battery Low, UPS
Overload, UPS Over Temperature, Weekly Schedule, Special Day Schedule.
3. Set the “UPS Shutdown Delay”, “Delay” and the warning intervals.
4. Select “Set Value” to confirm the changes.
N.B.: The shutdown module must be installed on the server/workstation to be protected, as described in the paragraph relating to “Shutdown software”.
Example: an example of the UPS output states for the following parameters is given below:
Time of AC failure 19:08
UPS shutdown delay = 120 sec
First warning = 5 sec
Warning interval = 30 sec
Delay for system shutdown = 60 sec
71
Chapter 6
Shutdown phases
UPS on
Warning messages
Time
19:08: 19:08: 19:08: 19:09:05
00
05
35
UPS
output
UPS shutdown
UPS output off
delay
19:15:00
19:17:00
Shutdown begins
Network failure
UPS
off
n
output
o
Duration
120 sec
1st warning
Program
action
3rd warning
Computer shutdown complete
Shutdown begins
p
q
r
Figure 6-5 Programming UPS shutdown in case of alarm
No.
1
Parameters
Delay
2
UPS Shutdown
Delay
3
1st warning
4
Warning interval
5
Shutdown delay
Description
Reference Menu
Delay time in minutes. After each UPS Control- Shutdown
enabled alarm, a shutdown signal will parameters
be activated – after this delay.
UPS Control – Shutdown
Parameters
Defines how many seconds after the UPS Control- Shutdown
beginning of the shutdown procedure parameters
before the UPS output will be switched UPS Control – Shutdown
off.
Parameters
Delay for the fist warning message
UPS Control- Shutdown
displayed on the screen of the conparameters
nected device (server or workstation). UPS Control – Shutdown
Parameters
Time interval for subsequent warning UPS Control- Shutdown
messages displayed on the screen of parameters
the connected device (server or work- UPS Control – Shutdown
station).
Parameters
Delay in receiving the shutdown com- Shutdown program
mand for powering down the system. (see the relevant Chapter).
Table 6-3 Parameters for programming UPS shutdown
72
Chapter 6
Display of automatic warning messages
In addition to the warning messages sent by the shutdown software, other warning messages may
be received from the Java Applet monitor, without having to keep a Browser window open.
To monitor the UPS parameters using Java Applets, you must install the Java Runtime Engine (JRE)
suited to the operating system in use and run the following command:
appletviewer http://<IPaddress>/PageJavaMonitor.html
where<IPaddress> is the NET VISION IP address
In this way it is possible to run the Java Applet on a PC at the user Log-in time; this solution enables
the display of warning messages in case of shutdown following the events defined in the menu “UPS
Management” – “Shutdown Parameters”.
Warning:
for correct operation of this feature, the following parameter must be disabled from the
CONTROL GROUP menu, accessing the NET VISION configuration menu via Telnet or
RS-232.
HTTP Security Control: Disabled
This disables the user name and password prompts for read only access to NET VISION.
73
Chapter 7
9. CHAPTER 7 - ”HISTORY LOG” MANAGEMENT
NET VISION internally supports a series of history logs, saving the most important parameter settings of the UPS and the agent (NET VISION).
Data is recorded in circular mode, whereas size of the log files depends on the parameters set in
“History Log Interval” and “Extended History Log Interval” in the “Net Vision Mgmt” – “Net Vision
Configuration” menu.
Display of the UPS History Log
Select “UPS History Log” from the main “UPS History” menu to display the history log. Click on the
appropriate row with the mouse to display the desired portion of the log.
Select “UPS Extended Log” from the main “UPS History” menu to display the extended log. Click on
the appropriate row with the mouse to display the desired portion of the log.
Select “UPS Events Log” from the main “UPS History” menu to display the UPS events log. Click on
the appropriate row with the mouse to display the desired portion of the log.
Select “Agent Event Log” from the main “UPS History” menu to display the NET VISION events log.
Click on the appropriate row to display the desired portion of the log.
Description of the UPS History Log
Figure 7-1 UPS History Log
This table gives a snapshot of some UPS Parameters. The old values are overwritten when the maximum number of entries (rows) is reached.
If there are no history logs available, the "No history logs available" message will be displayed.
The ”Super-user” can access the “manual Delete Entry” menu if necessary.
To save the table on the local disk of the computer used for the connection to NET VISION, select the
“SaveAsFile” option on the “File” menu on your Browser
74
Chapter 7
Log Date
The date on which the record was saved.
Log Time
Time at which the record was saved in 24-hour format.
Input Voltage
Input voltage when the data was saved, expressed in Volts (V1 for single-phase UPS and V1, V2,
V3 for three-phase UPS).
Output Voltage
Output voltage when the data was saved, expressed in Volts (V1 for single-phase UPS and V1, V2,
V3 for three-phase UPS).
Output Load
Percentage of the UPS load when the data was saved (L1 for single-phase UPS and L1, L2, L3 for
three-phase UPS).
Battery Capacity
Remaining battery capacity expressed in percentage of the total capacity when the data was saved.
Description of the UPS Extended Log
Figure 7-2 UPS Extended Log
This table gives a consolidated view of the UPS parameters taken over a set period of time.
The recording interval can be changed by the administrators modifying the "Extended Log Interval"
value in the “Net Vision Mgmt – Net Vision Configuration” menu. The minimum, maximum and average values are shown for each UPS parameter. The old values are overwritten when the maximum
number of entries is reached. If there are no history logs available, the "No history logs available"
message will be displayed. The Super-user can access the manual “Delete Entry” menu if necessary.
To save the table on the local of the computer used for the connection to NET VISION, select the
“SaveAsFile” option from the “File” menu on your Browser.
75
Chapter 7
Start Date
Date on which the data save started during the set interval.
Start Time
Time at which the data save started during the set interval.
End Date
Date on which the data save ended during the set interval.
End Time
Time at which the data save ended during the set interval.
Input Voltage (V1 - V2 - V3)
Maximum, minimum and average values of the input voltage during the set interval (V1 for singlephase UPS and V1, V2, V3 for three-phase UPS).
Output Voltage (V1 - V2 - V3)
Maximum, minimum and average values of the output voltage during the set interval (V1 for singlephase UPS and V1, V2, V3 for three-phase UPS).
Battery Capacity
Maximum, minimum and average values of the remaining battery capacity (in percentage) during the
set interval.
Total Load
Maximum, minimum and average values of the load during the set interval.
UPS Log Graphic Display
Select the command button
on the “UPS History” - “UPS History Log” menu or “UPS Extended Log” (at the bottom right of the screen page).
Selecting this menu lets you produce a log data trend graph. You can zoom on the data by moving
the red and green arrows in the window and then pressing the “Refresh” command button.
Description of the UPS Event Log
Figure 7-3 Description of UPS events
76
Chapter 7
This table lists all the UPS events that have occurred since the table was last cleared. The administrator can delete entries in the table.
Date
Date on which the event occurred, saved in dd/mm/yy format.
Time
Time at which the event occurred, saved in 24-hour format.
Event Description
Description of the event.
Description of the NET VISION Agent Events Log
Figure 7-4 NET VISION Agent events
This table lists all the NET VISION events that have occurred since the table was last cleared. The
administrator can cancel entries in the table.
Date
Date on which the event occurred saved in dd/mm/yy format.
Time
Time at which the event occurred saved in 24-hour format.
Event Description
Description of the event.
77
Appendix A
10. APPENDIX A - TECHNICAL INFORMATION
Depending on whether you are using NET VISION/CARD or NET VISION Box, refer to the appropriate Technical Information section.
NET VISION/Card Technical Information
Features
¾
¾
¾
¾
¾
¾
¾
¾
Set up from Web Browser, Telnet and serial port.
Management via SNMP manager and HTTP Web Browser.
MIB_II supported, SOCOMEC UPS MIB
Update via TFTP.
UPS Control.
Log File
Alarm Control.
UPS shutdown warning messages on all devices which run the shutdown software.
Technical Specifications
Serial Communication
Network Connection
UPS Protocol
Network Protocol
Supported MIB
Operating Temperature
Operating Humidity
Power Input
Power Consumption
Size
Weight
Regulatory compliance
Two asynchronous serial ports
10/100 BaseT RJ-45 plug
JBUS “P” protocol
SNMP on UDP/IP
HTTP on TCP/IP
ARP, RARP, TFTP and ICMP
MIB_II
SOCOMEC UPS MIB
0 to 40° C
10 to 80 %
8-12 VDC unregulated
Maximum 2.0 Watt
130 mm x 60 mm (L x W)
80 g
FCC class A
CE class A
78
Appendix A
NET VISION/Card Layout And Pin Assignment
NET VISION/Card Layout
Pins
Pin Assignment
Pin 1
Pin 3
Pin 5
Pin 7
Pin 9
Pin 1 to 25
Bottom side
GND
Txd_UPS
Txd_PC
NC
GND
NC
Pin 2
Pin 4
Pin 6
Pin 8
Pin 10
Pin 12 to 26
Component Side
9V DC
Rxd_UPS
Rxd_PC
Shortcircuited to pin 10
Shortcircuited to pin 8
NC
Description of DIP-switch functions
Layout of panel components
DIP-switch Definition
No.
1
2
3
4
SW1
OFF
OFF
ON
ON
SW2
OFF
ON
OFF
ON
Operating Mode
Normal mode
Reserved
Reserved
Special mode
79
Appendix A
NET VISION/Box Technical Information
Features
¾
¾
¾
¾
¾
¾
¾
¾
Set up from Web Browser, Telnet and serial port.
Management via SNMP manager and HTTP Web Browser.
MIB_II supported, SOCOMEC UPS MIB
Update via TFTP.
UPS Control.
Log File.
Alarm Control.
UPS shutdown warning messages on all devices which run the shutdown software.
Technical Specifications
Serial Communication
Network connection
UPS Protocol
Network Protocols
MIB Supported
Operating Temperature
Humidity
Power input
Power consumption
Size
Weight
Regulatory compliance
Two asynchronous serial ports
10/100BaseT RJ-45 plug
JBUS “P” protocol
SNMP on UDP/IP
HTTP on TCP/IP
ARP, RARP, TFTP and ICMP
MIB_II
SOCOMEC UPS MIB
0 to 40° C
10 to 80 %
12V DC unregulated
Maximum 2.0 Watt
134 mm x 86 mm x 27mm (L x W x H)
170g
FCC class A,UL,CUL,CE
80
Appendix A
Front Panel
TRAFFIC LED
STATUS LED
POWER LED
Rear Panel
12
UPS
Port 0
Network
Connector
COM
Port 1
DIP
Switch
Reset
Button
Description of DIP-switch functions
DIP-switch Definition
No.
1
2
3
4
SW1
OFF
OFF
ON
ON
SW2
OFF
ON
OFF
ON
Operating Mode
Normal mode
Reserved
Reserved
Special mode
81
Power
Inlet
Appendix A
LED Indicators
LED Indicator Definition
No.
1
2
3
4
5
Status LED
OFF
OFF
Flashing
Steady ON
OFF
Traffic LED
Steady ON
Flashing
OFF
Steady ON
OFF
6
7
Flashing
Steady ON
Flashing
Flashing
Operating Mode
Normal mode
Ethernet traffic
Default IP address
NET VISION error
UPS switched off (only if NET VISION is
powered by the UPS)
UPS connection error
Set-up mode
Serial Cable Specification
NET VISION/Box Serial port 0 cable (UPS cable)
RJ45
1
2
3
4
5
6
7
8
DB9 (Male)
8
2
5
Case GND
3
-
Description
Clear to send/ DC output
Not connected
Data received
Ground signal
Chassis ground
Data transmitted
Not connected
Not connected
N.B. : pins 2 and 7 of the RJ45 plug are connected internally.
NET VISION/Box serial port 1 cable (PC cable)
RJ45
1
2
3
4
5
6
7
8
DB9 (Female)
2
5
Case GND
3
Description
Not connected
Not connected
Data received
Ground signal
Chassis ground
Data transmitted
Not connected
Not connected
N.B.: pins 2 and 7 of the RJ45 plug are connected internally.
82
Appendix B
11. APPENDIX B – FIRMWARE UPGRADE
General Information
To upgrade the firmware, NET VISION must be connected to the same network as the PC used to
send the upgrade file (they must not be separated by routers or other devices for connection to different networks).
Check that “Network Upgrade” item on the NET VISION Control menu is enabled and that you have
the login user name and read/write password.
Firmware Upgrade using Unix
To perform firmware upgrade using a UNIX operating system, you must run the tftp command.
Run the following command line to download the upgrade file to NET VISION:
tftp -b <Net Vision IP> put <filename> upgrade@<password>@<username>
Where:
-b
<host>
put
<filename>
: Downloads the file in binary mode
: NET VISION IP address. For example: 172.168.1.18
: Sends the file
: name of the file which contains the firmware image.
Example: /mnt/floppy/NetVision100.bin
upgrade
@
<password>, <username>
: upgrade command
: separator character
: user name and password for read/write access.
Example:
NET VISION address
Image file name
Username
Password
: 172.168.1.18
: /mnt/floppy/NetVision100.bin
: NetVision
: public
The upgrade command becomes:
tftp -b 172.168.1.18 put /mnt/floppy/NetVision100.bin upgrade@public@NetVision
N.B.: Depending on the Unix or “Unix like” system you are using, the command syntax may vary. Please
refer to your operating system manual for more details on the TFTP protocol.
83
Appendix B
Firmware Upgrade using Windows 95/98/ME/NT4.0/2000/Xp
In order to upgrade the firmware, you must use the supgrade.exe program, included on the CD supplied with NET VISION.
This program is compatible with Windows 95/98/ME/NT4.0/2000/Xp, and later versions of these systems.
Once the program has been run, the following window will appear:
Program Features
UPS List
This lists the NET VISION addresses present on the LAN.
Discover button
Enables an automatic search for all the NET VISION systems connected to the LAN. All those found
will be automatically added to the UPS list.
Add button
Lets you manually add one or more NET VISION systems to the list.
Modify button
Lets you change the selected NET VISION parameters in the UPS list.
Upgrade button
Sends the program loaded with the “Open” button to the NET VISION you have selected on the list.
Open button
Lets you load the upgrade file to the sent to the NET VISION systems.
Remove button
Removes the selected NET VISION system from the list.
84
Appendix C
12. APPENDIX C - EMD SENSOR
Environmental Monitoring Device
Installation Manual
85
Appendix C
Introduction
The EMD (Environmental Monitoring Device) is a connectivity device that allows you to remotely monitor the
temperature, humidity, and status of two contact devices. It’s connection to the NET VISION enables monitoring or notification of alarms via standard Web browsers.
The EMD can be used with the UPS equipped with a NET VISION with firmware version 4.00 or higher.
When the EMD is plugged into the NET VISION communication port, temperature and humidity readings are
automatically displayed on the “NET VISION Comprehensive View” page. If enabled, the status of the external contact devices is also displayed on the same page.
Features
The EMD has the following features:
¾
Real-time temperature/humidity and other environmental conditions monitoring
¾
Monitors the status of two user-provided contact devices to protect your critical equipments
¾
Can be located away from the NET VISION with a straight-through CAT5 network cable up to 15m long
¾
User selectable alarm thresholds allow you define acceptable temperature or humidity limits
¾
Comprehensive environment conditions management and flexible configuration via Web Browser.
¾
Automatic events notification via E-mail and SNMP Trap
¾
Regularly records EMD parameters for statistical analysis and event diagnostics
¾
Configuration utility simplifies the firmware upgrade process
¾
Quick and easy installation (Hot-swappable)
86
Appendix C
Installation
With NET VISION CARD
Use the following steps to install the EMD to the NET VISION:
Before you install the EMD, the NET VISION should be installed into UPS first.
1.
Connect the supplied straight-through CAT5 network cable from the NET VISION’s RJ45 connector
labeled “COM” to the labeled “010101” port on the EMD.
2.
If applicable, connect external contact closure inputs to the screw terminals on the EMD.
3.
Verify that the NET VISION has a network connection, is installed in a UPS, and the UPS is plugged in
and turned on. The EMD is automatically recognized by the NET VISION.
4.
Run the Web browser and connect to NET VISION IP address. The home page of NET VISION appears.
5.
Change the setting of “EMD Status” from “Disable” to “Auto” on the EMD Configuration page (see
Figure C-1).
6.
Check the LED (Power/Status) of EMD. The LED will flash every 5 seconds (The flashing time is 3.).
7.
The temperature and humidity status is automatically displayed on the Comprehensive View page (see
Figure C-2).
NOTE: There are two models of EMD, EMD-HT and EMD-T. The EMD-HT supports both humidity and
temperature monitoring and the EMD-T supports only temperature monitoring. The NET VISION will recognize the models automatically and it will display the EMD type on the EMD Configuration page (see Figure 31).
87
Appendix C
Figure C-1 EMD Configuration Page
Figure C-2 Comprehensive View Page
88
Appendix C
With NET VISION BOX
Use the following steps to install the EMD to the NET VISION BOX:
1.
Connect the supplied RJ45/DB9(M) serial cable form the NET VISION RJ45 connector labeled “UPS” to
the COM port on the UPS.
2. Connect the supplied straight-through CAT5 network cable from the NET VISION RJ45 connector
labeled “PC” to the labeled “010101” port on the EMD.
3. If applicable, connect external contact closure inputs to the screw terminals on the EMD.
4. Insert the power connector in the NET VISION ’s power inlet.
5. Plug in the power adapter of the NET VISION into the power socket.
6. Verify that the NET VISION has a network connection, is installed in a UPS, and the UPS is plugged in
and turned on. The EMD is automatically recognized by the NET VISION.
7. Run the Web browser and connect to NET VISION IP address. The home page of NET VISION appears.
8. Change the setting of “EMD Status” from “Disable” to “Auto” on the EMD Configuration page (see
Figure 3-1).
9. Check the LED (Power/Status) of EMD. The LED will flash every 5 seconds (The flashing time is 3.).
10. The temperature and humidity status is automatically displayed on the Comprehensive View page (see
Figure 3-2).
NOTE: There are two models of EMD, EMD-HT and EMD-T. The EMD-HT supports both humidity and
temperature monitoring and the EMD-T supports only temperature monitoring. The NET VISION will recognize the models automatically and it will display the EMD type on the EMD Configuration page (see Figure C1).
89
Appendix D
13. APPENDIX D – REMOTE VIEW
What’s Remote View?
Remote View is an application running under Windows® 2000, Windows® XP, Windows® 2003, Windows®
VISTA, used for web monitoring through SNMP protocol of UPS equipped with Net Vision 4.11 or later.
The control of the devices is provided both with tree-view and list-view, with Icon style and Report style
indications. Whe trap happens, according to the severity level, the icon of the device will change colour and a
mail will be automatically sent to all addresses defined by the user.
To make geographical or building control easy and build a view of the real allocation of the UPSs, it is possible to insert maps and custom layouts in .jpg, .bmp and .gif format.
Remote View can manage up to 1024 devices simultaneously and the hierarchy structure can have up to 8
levels.
Caution!
In order to set and use Remote View properly, it is necessary to know the IP Address, User Name and
Password of each Net Vision device.
Minimum System Requirements.
•
•
•
•
•
•
Windows® 2000, Windows® XP, Windows® 2003, Windows® VISTA operating system
E-mail client;
Pentium 4 processor (equivalent equivalent processor or later);
256 Mb RAM;
1024x768 video resolution;
CD-ROM drive.
Installation.
Please, follow the instructions you find on Remote View’s Help on Line.
90
Appendix D
Visit our site if you require further information or if you need to
contact the after sales customer support
www.socomec.com
91
">