CONCORD 5330z Instruction manual

CONCORD 5330z Instruction manual
SYSTEM REQUIREMENTS WINDOWS
• Windows®98/98 SE/Windows®2000 Prof./ Windows® Me / Windows®XP
• 32 MB RAM
• 110MB free memory capacity
• VGA colour monitor
• CD ROM drive
• USB
SYSTEM REQUIREMENTS
IMac,iBook,G3 blue&white series,G4 series
• MacOS 9.0~10.1.3
• 64 MB RAM or higher
• 110MB free memory capacity
• VGA colour monitor
• CD ROM drive
• USB
Thank you for purchasing the Concord Eye-Q-5330z.
Please take the time to read through this instruction manual so you can enjoy all
its features.
This mark on your camera certifies that this camera meets the requirements of the
EU (European Union) concerning interference causing equipment regulations.
CE stands for Conformité Européenne (European Conformity).
Digital Camera
Concord Eye-Q 5330z
Tested To Comply
With FCC
Standards
FOR HOME OR OFFICE USE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference recieved, including interference that may
cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Do not remove the ferrite cores form the cables.
3
FOR PROPER AND SAFE USE
Read and understand all warnings and cautions before using this product.
This is a descriptive statement warning of the result if the instructions are
ignored or not understood.
WARNING
Batteries may become hot or explode due to improper use.
• Use only the batteries specified in this instruction manual.
• Do not install the batteries with the polarity (+/-) reversed.
• Do not attempt to recharge, short, or disassemble.
• Do not mix batteries of different types, brands, ages or charge levels.
• Follow local regulations for battery disposal.
Use caution, accidents may occur when using this product near young chil-dren.Keep batteries or
things that could be swallowed away from young children.Contact a doctor immediately if an object
is swallowed.Immediately remove the batteries and discontinue use if...
• The camera is dropped or subjected to an impact in which the interior is exposed.
• The product emits a strange smell, heat, or smoke.
Do not walk while looking at the monitor.
Do not disassemble. Electric shock may occur if a high voltage circuit inside
the camera is touched.
• Do not use the batteries which show wear or damaged.
• Do not expose batteries to fire,high temperature environment,water or moist places.
• Do not store the batteries nearby the metalic products.
4
• Never charge alkaline betteries.
• Do not use leaking batteries.If fluid from the batteries in your eyes,immediately rinse eyes with lots
of fresh water and contact the doctor.If fluid from the batteries makes contact with your skin or
clothing,please wash the area smoothly.
• Only use the specified AC adapter within the voltage range described on the adapter unit.An specification unknown adapter may cause damage.
• Immidiately remove the batteries or unplug the AC adapter and discontinue use if the camera was
dropped or shocked by an impact in which the interior,especially the flash part is exposed.
• Do not fire the flash directly into the eyes or at vehicle operators.It may cause eyesight injury or
blind or an accident in series.
• Do not use the camera in a humid environment,or operate with wet hands,If any liquid flow into the
camera,immediately remove the power supply(Include batteries and adapter)and discontinue use.
Or it may cause electric shock.
• Do not use the camera near inflammable gases or liquids and use them to clean the camera like
gasoline,benzine,or paint thiner.Or it may cause an explosion or fire.
• Do not just pull on the power cord while unplugging from the outlet on the wall.Hold the adapter
plug unit is recommend.
• Do not damage,twist,modify,heat or place heavy objects on the power cord of the AC adapter.A
damaged power cord may cause damage.
• Do not continue to use if the camera has a odor ,smoke or something strange.Immediately remove
the power supply taking care not to burn yourself.
5
CAUTION
The heat of the camera rises with extended periods of use. Use cautionsly when handling the camera
or removing the batteries and compact flash card.
• Do not leave the camera in places subject to extermely high temperatures,like a sealed
vehicle,direct sunlight or other places of high temperature.
• Exposure to high temperature may adversely affect the internal components of the camera.
• Do not cover the AC adapter plug unit with anything when in use.It may cause heat to build up and
distort the camera case or cause fire.
• Always unplug the camera from power supply for safety purposes whwn the camera is not in use
for long periods.
• Allowing dust to accumulate in the camera over a long period is hazardous as extreme circumstances may cause a fire.It is best to clean the camera prior to seasonal periods of high humidity.
• Consult your dealer for information on the cost of cleaning your camera.
6
BEFORE YOU BEGIN
Check the packing list before you begin. If some parts are missing, contact your
camera dealer or call our customer service hotline listed on the warranty card.
• Concord Eye-Q-5330z zoom camera (x 1)
• AA-size Alkaline Batteries (x 4)
• Video Cable (x 1)
• Hand Strap (x 1)
• Camera Case (x 1)
• Mini-USB Cable (x 1)
• 32 MB CompactFlash Card (x 1)
• Software and Documentation on CD-ROM:
USB Driver Software for Windows ® 98/Windows ® 98 SE / Windows ® 2000 / XP
and Mac OS 9.0~10.1.3
Instruction Manual (PDF) Windows ® /Macintosh
Photo Impression, Video Impression
• Documentation (Printed)
Warranty Card (x 1)
7
TABLE OF CONTENTS
FOR PROPER AND SAFE USE . . . . . . . . . . .4
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . .7
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . .8
NAMES OF PARTS . . . . . . . . . . . . . . . . . . . .12
CAMERA BODY . . . . . . . . . . . . . . . . . . . .12
INSIDE THE TERMINAL COVER . . . . . .14
BOTTOM OF BODY . . . . . . . . . . . . . . . . .14
DATA PANEL . . . . . . . . . . . . . . . . . . . . . .15
VIEWFINDER . . . . . . . . . . . . . . . . . . . . . .16
AUTO POWER OFF . . . . . . . . . . . . . . . . . .28
USING THE DC
ADAPTER (Sold Separately) . . . . . . . . . . .28
INSERTING/REMOVING THE COMPACT
FLASH (CF) CARD . . . . . . . . . . . . . . . . . . . . .29
INSERTING THE CF CARD . . . . . . . . . . .29
REMOVING THE CF CARD . . . . . . . . . . .30
QUICK REFERENCES . . . . . . . . . . . . . . . . .18
GETTING STARTED . . . . . . . . . . . . . . . . . . .18
TAKING PICTURES . . . . . . . . . . . . . . . . . . . .18
MONITORING THE CAPTURED IMAGES . .20
DELETING IMAGES . . . . . . . . . . . . . . . . . . .21
TAKING PICTURES
BASIC RECORDING PROCEDURE. . . . . . . . .33
THE RECORDING MODE DISPLAY ON THE
LCD MONITOR . . . . . . . . . . . . . . . . . . . . . . . .35
THE DISPLAY OF THE CAMERA SETTINGS .36
ADJUSTING THE FOCUS . . . . . . . . . . . . . . . .37
FOCUS LAMP . . . . . . . . . . . . . . . . . . . . . . .37
PREPARATION
ATTACHING THE HAND STRAP . . . . . . . . . .24
INSERTING THE BATTERIES . . . . . . . . . . . .25
CHECKING THE BATTERY POWER . . .27
FOCUS DISTANCE IN THE AUTOFOCUS
MODE (Minimum Focus Distance)....................37
THE SUBJECT THAT IS DIFFICULT TO
FOCUS
8
IN THE AUTOFOCUS MODE . . . . . . . . . . . . .38
WHEN THE SUBJECT IS NOT IN THE
CENTER OF THE FRAME
(Focus Lock Function) . . . . . . . . . . . . . . . . .39
ADJUSTING THE FOCUS DISTANCE . . . .40
CLOSE UP . . . . . . . . . . . . . . . . . . . . . . . . .41
ADJUSTING THE FOCUS AREA . . . . . . . .43
FLASH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
FLASH RANGE . . . . . . . . . . . . . . . . . . . . .44
SELECTING THE FLASH MODE . . . . . . .45
FLASH LAMP . . . . . . . . . . . . . . . . . . . . . ..46
ADVANCED OPERATIONS
P/A/S/M EXPOSURE
EXPOSURE MODES . . . . . . . . . . . . . . .48
DIGITAL ZOOM . . . . . . . . . . . . . . . . . . . . . . . .50
BURST IMAGE CAPTURE . . . . . . . . . . . . . . .52
SELF-TIMER . . . . . . . . . . . . . . . . . . . . . . . . . .54
ISO SETTING . . . . . . . . . . . . . . . . . . . . . . . . .56
EXPOSURE COMPENSATION . . . . . . . . . . ..57
MOVIE CLIP SHOT . . . . . . . . . . . . . . . . . . . . . .59
MOVIE CLIP PLAYBACK . . . . . . . . . . . . .60
MOVIE CLIP SETTING . . . . . . . . . . . . . . .60
VOICE RECORDING . . . . . . . . . . . . . . . . . . .61
VOICE PLAYBACK . . . . . . . . . . . . . . . . .62
SPECIFYING THE RECORDING MODE
SPECIFYING THE RECORDING MODE . . . .64
THE RECORDING MODE MENU DISPLAY
(LCD Monitor) . . . . . . . . . . . . . . . . . . . . .64
RECORDING MODE MENU ITEMS . . . .64
SPECIFYING IMAGE QUALITY MODE . . . . .68
SPECIFYING THE IMAGE SIZE MODE . . . .71
SPECIFYING WHITE BALANCE MODE . . . .73
SPECIFYING THE SHARPNESS MODE . . .75
RESETING TO THE RECORDING MODE DEFAULT
SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
9
PLAYBACK MODE
SINGLE-FRAME PLAY . . . . . . . . . . . . . . . . . . 80
THE PLAYBACK MODE DISPLAY ON THE
LCD MONITOR . . . . . . . . . . . . . . . . . . . . .81
THE IMAGE INFORMATION DISPLAY
IN THE PLAYBACKMODE . . . . . . . . . . . . .82
INDEX PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . 83
ZOOM PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . 85
SLIDE SHOW
TO START THE SLIDE SHOW . . . . . . . . .87
TO STOP THE SLIDE SHOW . . . . . . . . . .88
THE SETTING IN THE SLIDE SHOW
MODE MENU . . . . . . . . . . . . . . . . . . . . . .89
DELETING IMAGES
DELETING SELECTED IMAGE . . . . . . . . . . .92
DELETING ALL IMAGES. . . . . . . . . . . . . . . . .95
DELETING FOLDERS . . . . . . . . . . . . . . . . . .97
ADJUSTING THE BRIGHTNESS OF THE LCD
MONITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
10
SPECIFYING THE PLAYBACK MODE
THE PLAYBACK MODE MENU . . . . . . . . . .101
THE PLAYBACK MODE MENU
(LCD Monitor) . . . . . . . . . . . . . . . . . . . . . . .101
THE PLAYBACK MODE MENU ITEMS AND
EACH SETTINGS . . . . . . . . . . . . . . . . . . . .101
SPECIFYING THE PRINT SETTINGS WITH
THE DPOF . . . . . . . . . . . . . . . . . . . . . . . . . .103
SPECIFYING THE IMAGE AND THE
NUMBER TO BE PRINTED . . . . . . . . . .104
SPECIFYING THE INDEX PRINT
SETTINGS . . . . . . . . . . . . . . . . . . . . . . .106
TO CANCEL THE PRINT SETTINGS WITH
THE DPOF . . . . . . . . . . . . . . . . . . . . . . .108
FOLDER NAME . . . . . . . . . . . . . . . . . . . . . .109
SELECTED AN FOLDER . . . . . . . . . . . .110
GIVE FOLDER A NEW NAME . . . . . . . . .111
On DCF (Design rule for Camera File system)
FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
SETUP
THE SETUP MODE MENU DISPLAY . . . . . .115
THE SETUP MODE MENU DISPLAY ON
THE LCD MONITOR . . . . . . . . . . . . . . . . .115
THE SETUP MODE MENU ITEMS AND
EACH SETTINGS . . . . . . . . . . . . . . . . . . .115
SPECIFYING THE TIME FOR THE AUTO
POWER OFF FUNCTION . . . . . . . . . . . . . . .117
FORMATTING THE CFCARD . . . . . . . . . . .119
SETTING THE DATE / TIME . . . . . . . . . . . .121
SETTING THE BEEP SOUND . . . . . . . . . . .123
SWITCHING THE VIDEO SIGNAL FROM
THE VIDEO OUTPUT TERMINAL . . . . . . . .125
SWITCHING THE LANGUAGE DISPLAYED
ON THE LCD MONITOR . . . . . . . . . . . . . . . .127
RESETTING TO THE DEFAULT SETTINGS. 128
CONNECTING TO THE PERSONAL COMPUTER
CONNECT TO PERSONAL COMPUTER
For Windows . . . . . . . . . . . . . . . . . . . . . .131
For Macintosh . . . . . . . . . . . . . . . . . . . . 141
CAUTIONS WHEN CONNECTING TO
THE PERSONAL COMPUTER . . . . . . .146
INSTALLING PhotoImpression &
VideoImpression . . . . . . . . . . . . . . . . 135&141
APPENDIX
WATCHING THE CAPTURED IMAGES
ON TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
TROUBLESHOOTING . . . . . . . . . . . . . . . . 151
NOTES ON THE HANDLING . . . . . . . . . . .155
CARE AND STORAGE . . . . . . . . . . . . . . . .159
TECHNICAL DETAILS. . . . . . . . . . . . . . . . 160
11
NAMES OF PARTS
CAMERA BODY_FRONT VIEW
* Do not touch.
12
CAMERA BODY_REAR VIEW
13
INSIDE THE TERMINAL COVER
USB connector
Video-out terminal
DC terminal
BOTTOM OF BODY
Battery-chamber door
Tripod socket
14
DATA PANEL
The following diagram shows all items displayed to aid the explanation.
Image-size indicators
Flash-mode indicators
Battery-condition indicator
Self-timer indicator
Number display of recordable remaining frame/
No-card indicator
* Refer to the number of recordable remaining frame as a guide.
The number changes depending on the scene or subject you record.
15
VIEWFINDER
Focus Iamp
(green)
Close-framing guide
Flash Iamp
(red)
Close-framing guide
When you shoot a subject which is closer than 1m through the viewfinder, only the part under the
close-framing guide is recorded. So, use the LCD monitor to check the image composition when you
shoot a subject which is closer than 1m.
16
Focus Lamp (Green)
Lights.
Blinks quickly (about 8
times in a second).
The focus is determined and locked.
The focus is not determined.
(The subject contrast is too low, the subject is too dark or too close.
Or the subject is too far in the close up mode.)
Blinks slowly (about 2
times in a second).
The image is being recorded in the CF (Compact Flash) card.
The camera reads out the image from the CF card.
Focus Area (as a Guide)
In the autofocus mode,
the focus is adjusted at
the gray part as shown
in the figure.
Flash Lamp (Red)
Lights.
Blinks quickly when the shutter-release
button is pressed full-way down
(about 8 times in a second).
(When the flash function is cancelled)
Blinks slowly (about 2 times in a second).
The flash ready for fires.
The flash is being charged.
The shutter-release button is not released.
The shutter speed becomes slow.
Taking a picture in this mode may cause
an image blurred.
17
QUICK REFERENCES
GETTING STARTED
1 Insert the batteries (see page 25).
2 Insert the CF card (see page 29).
Caution:
We advised to use Sandisk or Hitachi CF card.
TAKING PICTURES – See page 33 for details.
1 Rotate the function dial to
.
2 Slide the power switch to turn on the camera.
18
3 Determine the image composition while looking into the
LCD monitor or viewfinder.
4 Adjust the image range and size with the four-way keys
(
/
).
• When the
• When the
key is pressed, the image size becomes large.
key is pressed, the image range becomes wide.
5 Press the shutter-release button half-way down.
• When the image is focused, the focus lamp (green) lights up.
6 Press the shutter-release button full-way down to take the
picture.
• The captured image is displayed on the LCD monitor.
• While the captured image is recorded in the CF card, the focus lamp (green)
blinks slowly (about 2 times in a second).
19
MONITORING THE CAPTURED IMAGES – See page 82 for details.
1 Rotate the function dial to
.
2 Slide the power switch to turn on the camera.
• The latest image (which was recorded last) is displayed on the LCD monitor.
3 When the
or
key is pressed, the image changes to the
next or previous one respectively.
20
DELETING IMAGES – See page 92 for details.
1 Display the image to be deleted on the LCD monitor by performing from steps 1 to 3 of "MONITORING THE CAPTURED IMAGES" described on the previous page.
2 Press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
3 After confirming that [SELECTED IMAGE] is highlighted,
press the
key.
4 When the selected image is highlighted, press the LCD to
select, then press the ENTER button.
21
• The image to be deleted is displayed on the LCD monitor and the display to
conform whether you delete the image or not appears as shown in the figure.
5 Press the
the
key.
key so that [YES] is highlighted and press
• The image displayed on the LCD monitor in step 1 is deleted.
6 To complete the operation of deleting an image, after confirming that [NO] is highlighted in the display to confirm,
press the ENTER button.
• The LCD monitor display returns to the playback mode menu.
7 Press the MENU button.
• The LCD monitor display returns to the playback mode.
22
PREPARATION
23
ATTACHING THE HAND STRAP
1 Insert the smaller loop of the hand strap through the strap
eyelet.
2 Insert the other end of the hand strap through the small
loop.
24
INSERTING THE BATTERIES
This camera uses four AA-size alkaline or Ni-MH batteries.
* When using AA-size Ni-MH batteries, fully recharge them with a vendor-endorsed battery charger.
1 When replacing the batteries, slide the power switch to turn
off the camera.
• You may skip this step when inserting the batteries for the first time after a
purchase.
2 Slide the battery-chamber door slightly in the 1 direction
and open it in the 2 direction.
3 Insert the batteries by following the +/- diagram indicated in
front of the battery-chamber door.
25
4 Close the battery-chamber door in the direction of the arrow
1 and slide it until it clicks 2 .
• After replacing the batteries, check that the built-in clock (date and time) works correctly (See page
121).
If neither AC adapter nor batteries are used more than 5 minutes, the built-in clock may delay or be
reset to the default setting. In this case, set the date and time again by following the procedure
described on page 121.
• Do not place the camera with the battery-chamber door facing down when the battery-chamber
door is open. Doing so may damage the battery-chamber door.
• As the batteries become hot right after the camera is operated, be careful when replacing the batteries.
26
CHECKING THE BATTERY POWER
When the batteries are installed in the camera, the camera checks the battery power automatically
and shows the result on the data panel.
lights - The battery power is sufficient.
Lights - Prepare the new batteries. Even in this status, the recording
or playback can be performed.
All indicators go out and after that, blinks for 5 seconds and then, all
indicators go out again.
- Perform the following either operation.
• Replace all batteries with new ones.
• Remove all batteries and use the AC adapter (sold separately ) (see page 28).
Taking a picture or playing back cannot be excuted.
* When nothing is displayed on the data panel, check that the batteries are installed with a correct
polarity (+/-). When nothing is displayed even though the batteries are installed correctly, replace
the batteries with new ones.
27
AUTO POWER OFF
To save the battery power, This camera will turned off automatically if it is not operated more than 5
minutes. (Auto Power Off function)
To operate the camera, slide the power switch to turn on the camera again.
• When using the batteries, the time for the auto power off function can be changed to 1 minute, 3
minutes, 10 minutes or 30 minutes. See page 117 for details.
• When using the AC adapter (sold separately), this camera will turn off automatically if it is not operated more than 30 minutes. The time for the auto power off function is fixed in 30 minutes.
USING THE AC adapter (Sold Separately)
We recommend you to use the AC adapter (sold separately) when using the camera indoor where
the AC outlet supplies the power to the camera or when connecting the camera to the personal computer for editing the images.
Be sure to turn off the power of the camera when changing the power supply from the batteries to the
AC adapter or vice versa. Do not change it when the power of the camera is turned on.
1 Connect the mini plug of the AC adapter to the DC terminal
of the camera.
• The Shape of the mini plug may vary depending on the AC adapter.
2 Connect the power plug of the AC adapter to an AC outlet.
28
INSERTING/REMOVING THE COMPACT FLASH(CF) CARD
Be sure to turn off the power of the camera when inserting or removing the CF card into or from
the camera. Otherwise, the data in the card may be lost or the card may be damaged.
If you insert or remove the CF card when the camera is turned on, re-format the CF card after transferring the data from the card to your computer if the data is safe.
INSERTING THE CF CARD
1 Open the card-slot door as shown in the figure.
2 Insert the CF card into the card slot.
• Position the front of the card towards the camera lens and insert the card
with the signal part facing down until the card stops.
• Insert the card straight. Do not insert it on the angle.
• If the card is stopped halfway, check the direction of the card. Forcing the
card into the slot may damage the card or the camera.
29
INSERTING/REMOVING THE COMPACT FLASH(CF) CARD
3 Fold the card-release lever down as shown in the figure.
• Be sure to fold the lever. Otherwise, the card-slot door cannot be closed.
4 Close the card-slot door until it clicks.
REMOVING THE CF CARD
1 Confirm that the power of the camera is turned off.
2 Open the card-slot door as shown in the figure.
30
INSERTING/REMOVING THE COMPACT FLASH(CF) CARD
3 Lift the card-release lever up as shown in the figure.
4 Push in the card-release lever straight.
• As the CF card ejects slightly from the camera, pull out the card.
• Be careful with the card because it may be hot.
• Keep the CF card in the protection bag supplied with the card.
5 Close the card-slot door until it clicks.
31
TAKING PICTURES
32
BASIC RECORDING PROCEDURE
1 Rotate the function dial to
.
2 Slide the power switch to turn on the camera.
• The power switch returns to the initial position.
When the power switch on in the recording mode, the initial setup for LCD
monitor is off, if you need turn on the LCD, please press
once.
3 Determine the image composition while looking into LCD
monitor or viewfinder.
• When holding the camera, be sure not to cover the lens with your fingers and
so on.
• When the focus is not adjusted on the subject, use the focus lock function
(see page 39).
4 Adjust the image range and size with the
/
keys.
• When the
key is pressed, the image size becomes large (Telephoto
mode). When the
key is pressed, the image range becomes wide (Wideangle mode).
33
5 Press the shutter-release button half-way down.
• The camera adjusts the focus automatically. When the subject is focused,
the focus lamp (green) lights up.
• When the focus lamp (green) blinks, follow the operation from step 3 again.
• When the flash will fire, the flash lamp (red) lights up.
• When the flash lamp (red) blinks slowly (about 2 times in a second), the
shutter speed becomes slow. Taking a picture in this mode may cause an
image blurred. We recommend you to take pictures after fixing the camera
on the tripod.
* When pressing the
shutter-release button, there is a point
where the button
stops halfway. To
6 Press the shutter-release button the rest of the way down.
press the shutterrelease button to this • If the flash lamp (red) blinks when the shutter-release button is pressed fullway down, the flash is being charged. When the shutter-release button is
point is described
kept pressed in this status, the shutter is released at the same time when
"Press half-way
down" in this manuthe flash is charged.
al.
• The captured image is displayed on the LCD monitor and is recorded in the
CF card. While the image is recorded, the focus lamp (green) blinks slowly
(about 2 times in a second) and "RECORDING" blinks on the LCD monitor
slowly. Be sure not to open the battery-chamber door, disconnect the plug
of the AC adapter or remove the CF card until the recording in the CF card
is completed (until the focus lamp (green) and "RECORDING" stops blinking). otherwise,The data in the CF card may be damaged or lost..
34
THE RECORDING MODE DISPLAY ON THE LCD MONITOR
Each time the display button
is pressed, the display on
the LCD monitor changes in the following order.
The LCD monitor is turned off
Live view
(The camera settings are not displayed)
Live view
(The camera settings are displayed)
35
THE DISPLAY OF THE CAMERA SETTINGS
(For details, see the pages in parentheses)
36
ADJUSTING THE FOCUS
FOCUS LAMP
When the shutter-release button is pressed halfway, this camera adjusts the focus automatically and
the focus lamp (green) shows the focus status (when the focus mode is set to the autofocus mode.)
Lights
Blinks quickly
(abort 8 times in a second)
The focus is determined and locked.
The focus is not determined.
The shutter can be released.
When the focus lamp (green) blinks, check the following points:
• Do you attempt to adjust the focus on the subject which is difficult to focus in the autofocus mode?
(See page 38).
• Is the subject closer than the minimum focus distance (or farther than 40 cm in the close up mode)?
(Refer to the followings.)
FOCUS DISTANCE IN THE AUTOFOCUS MODE (Minimum Focus Distance)
The focus distance in the autofocus mode is described on the list below.
When the subject is closer than the minimum focus distance (0.4m) or farther than 40 cm in the close
up mode, the focus lamp (green) blinks.
Standard mode
Close up mode
(Refer to the page 53)
0.4m to ∞ (infinity)
8 cm to 40 cm
37
THE SUBJECT THAT IS DIFFICULT TO FOCUS IN THE AUTOFOCUS MODE
The autofocus mode uses the image contrast (the difference of light and dark parts) on the CCD
(Charge Coupled Device) to focus on. Therefore, with the autofocus mode, the focus may not be
adjusted correctly on the following subjects. In this case, use the focus lock function (see page 39),
that you once focus on the other subject which is at the same distance as the subject you want to take
the picture and change the image composition.
38
The subject is too dark.
Some subjects at different
distances overlap in the
focus range.
The subject has no contrast such as a blue sky or
a white wall.
The subject is too bright
such as a shining car body
or a surface of water.
WHEN THE SUBJECT IS NOT IN THE CENTER OF THE FRAME
(Focus Lock Function)
When the subject is not in the center of the frame, the camera adjusts the focus on the background. In
this case, take a picture with the focus lock function.
1 Aim the camera so that the subject is in the center
of the frame and press the shutter-release button
half-way down.
• The camera adjusts the focus automatically. When the focus is
adjusted, the focus lamp (green) lights.
2 While you hold pressing the shutter-release button
half-way down, change the camera position to
obtain the desired image composition and press the
button full-way down to take a picture..
39
ADJUSTING THE FOCUS DISTANCE
Keep pressing
key allows you to adjust the Focus Distance to the best situations.
Auto focus The camera will automatically adjust the focus according to distance to subject.
(No icon)
The camera will adjust the focus to infinity.Flash was default to be disabled.
Landscape
The camera will focus closely to subject from 8 cm to 40cm.
Close up
The camera will focus to specified distance, there are 0.5m,1.0m and 2.5m.
Specified
1 Rotate the function dial to
.
• Be sure that camera is turned on.
2 Press
continuously to change the focus distance.
• The icons on upper-right side of the LCD monitor will be changeable.
3 Press the shutter release half-way down to adjust the focus.
40
CLOSE UP
The close up function allows you to take a picture close to the subject up to 8 cm filling the frame with
the subject in about 6 cm x 4 cm.
1 Rotate the function dial to
.
• The recording mode menu is displayed on the LCD monitor.
2 Press
button to change the Focus distance to
.
•
is displayed on the upper right side of the LCD monitor and it shows that
the close up mode is selected.
• The flash mode is set to "FLASH CANCEL"
automatically. When the
close up mode is selected, the flash does not fire.
3 Determine the image composition while looking into the
LCD monitor.
• There is a difference between the image range through the viewfinder and
the actual one in the close up mode. We recommend you to use the LCD
monitor when you determine the image composition.
• We recommend you to fix the camera on the stable or on the tripod.
• The LCD monitor cannot be turned off in the close up mode.
41
4 Press the shutter-release button half-way down.
• If the focus lamp (green) blinks, check that the subject is within the distance
from 8 cm to 40 cm (is not apart more than 40 cm from the camera).
5 Press the shutter-release button full–way down to take the
picture.
• Even after taking a picture, the close up mode is not cancelled. When the
camera is turned off and on again, the camera enters autofocus mode.
• When the camera enters the autofocus mode, the flash mode is returned to
"AUTOFLASH WITH RED-EYE REDUCTION".
42
ADJUSTING THE FOCUS AREA
Adjust the focus area while looking into the LCD monitor.
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor
2 Press the
press the
Central
or
key so that [FOCUSING] is highlighted and
key.
3 Press the or
key to select desired focus area and press
key to finish the setting.
Spot
43
FLASH
With this camera, the following 5 flash modes are available. You can select them according to your
purpose or condition.
AUTOFLASH
FILL-FLASH
FLASH
CANCEL
The flash fires automatically when the light level
is low or the subject is backlit.
The flash fires every time a picture is taken
regardless of the brightness.
Select this mode to reduce the harsh shadows
when you take the picture outdoor and the subject’s face is shaded with a hat and so on.
The flash does not fire. Select this mode when
taking a picture in the place where the flash photography is prohibited such as in a museum, etc.
AUTOFLASH WITH RED-EYE
REDUCTION
The flash fires the short burst 2 times before the
main flash burst for reducing the red-eye phenomenon. Select this mode when taking the picture of
people or animals in the dark
NIGHT MODE
*The flash fires even in long shutter night mode,to
get satisfied exposure on subject and background.
Flash Range
The flash range has the limit. Take pictures by referring to the flash range indicated below
The flash range:Tele 0.5m~2.5m
The flash range:wide 0.5m~3m
44
SELECTING THE FLASH MODE
1 Rotate the function dial to
.
• The recording mode menu is displayed on the LCD monitor.
2 Press
key to change the Flash mode as follows :
AUTOFLASH
FILL-FLASH
FLASH-CANCEL
AUTOFLASH WITH RED-EYE
REDUCTION
NIGHT MODE
45
*The camera usually shows the icon
shot with FLASH-CANCEL mode
on the upper-left side of the LCD monitor when taking a
to a darker subject. It hints you to hold your camera in stable.
• The selected flash mode is displayed with the icon shown on the previous page on the upper right
side of the LCD monitor (see page 36).
• The flash mode returns to "AUTOFLASH WITH RED-EYE REDUCTION" when the camera is turned
off and on again.
Flash Lamp
The flash lamp (red) shows the flash status.
Lights
The flash rdady for fires.
Blinks quickly when the shutterThe flash is being charged. The shutter-release
release button is pressed all the way button is not released.
down (abort 8 times in a second).
The shutter speed becomes slow. Taking a picture
Blinks slowly (when the flash funcin this mode may cause an image blurred.
tion is cancelled). (about 2 times in a The flash function is cancelled when the flash
second).
mode is set to "FLASH CANCEL", when the drive
mode is set to the burst image capture or, when the
focus mode is set to the close-up mode.
46
ADVANCED OPERATIONS
47
P/A/S/M EXPOSURE
EXPOSURE MODES
These 4 exposure modes allow extensive control over general photo taking.Programmed Auto P
gives carefree operation;Aperture Priority A and Shutter Priority S allow users to maximize
exposures in different case;Manual Exposure M provides complete freedom in controlling.
Options
Purpose
Programmed auto The camera will automatically set the
shutter speed and aperture value for
best state.
Aperture priority
the user selects the aperture and the
(F3.37-F15)
camera sets the fit shutter speed.
Shutter priority
(1/2600s-8s)
Manual exposure
48
When to use it
Recommened in most situations.
Recommened in controlling the depth of
field (makes the main subject standing out
from surrounding).
Recommened in freeze the action of fastthe user selects the shutter speed
and the camera sets the fit aperture. moving subject or creat a sense of motion
of slower-moving subject.
You can complete control anything of
the user selects both the shutter
exposure.
speed and aperture.
In P/A/S/M menu:
(Rotate the function dial to
and press MENU button.)
1 Press the
/
key so that [P/A/S/M Exposures] is highlighted and press
key.
2 Select the desired mode by pressing
/
,and Press
key to confirm the settings.
In A/S/M mode:
Programmed Auto
Aperture Priority
Shutter Priority
1. Press
speed.
/
key to change the desired value of aperture or shutter
Manual Exposure
Aperture Priority
Shutter Priority
Manual Exposure
You can adjust both aperture and shutter speed in M mode.
2. Press shutter release button half-way down to adjust.
3 Press MENU button to quit the setting.
49
DIGITAL ZOOM
The digital zoom function can increase the maximum magnification (about 24 mm) of the optical zoom
lens (102 mm in the 34 mm film format equivalent) up to 2 times.
1 In the recording mode, press the
key in the recording
mode so that the image is zoomed to the maximum.
2 Press and hold the
key for more than 2 seconds.
• The digital zoom function is set.
• The indicator that shows the image range appears on the LCD monitor as
shown in the figure left below. When the indicator appears, remove your finger from the
key.
• The digital zoom function cannot be set when the LCD monitor is turned off.
50
3 While looking into the LCD monitor, determine the image
composition so that the desired image is positioned within
the range of the indicator.
4 Press the shutter-release button half-way down.
5 Press the shutter-release button full–way down to take a
picture.
• The focus lock function can be also used (see page 39).
• Even after taking a picture. The digital zoom is not cancelled. To cancel the
digital zoom function, press and hold the
key until the indicator disappears or turn off and on the camera again.
51
CONTINUOUS SHOOTING
This digital camera will continuously take pictures while the shutter-release button is held down.
The maximum number of images that can be captured at a time in follows(with 32MB CF card):
Image quality
FINE (Fine)
STD. (Standard)
ECON. (Economy)
The maximum number of the pictures (as a guide)
2560 x 1920 size
1600X1200 size
about 13 pictures
about 30 pictures
about 26 pictures
about 60 pictures
about 52 pictures
about 90 pictures
* See page 68 for the image quality and page 71 for the image size.
* The number of the picture you can take sequentially at a time describe on the list above can be referred as a guide.
The number of the picture changes according to the scene or subject you record.
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor.
2 Press the ENTER button to select [DRIVE MODE] as follows:
• The continuous icon
appears on the upper right side of the LCD monitor.
(See page 36)
52
Single shot
Continuous shot
Continuous with AF
Self-timer
• When taking a continuous shot,The flash mode is set to "FLASH CANCEL"
automatically.
• When the single shot or the self-timer shot is selected, the flash mode returns to "AUTOFLASH
WITH RED-EYE REDUCTION".
53
SELF-TIMER
The picture is taken about 10 seconds after the shutter-release button is pressed.
1 After fixing the camera on the tripod, rotate the function dial
to
.
2 Press ENTER button to still change the [DRIVE MODE]
to SELF-TIMER
.
Single shot
1 shot even keep pressing shutter release.
Continuous shot
Continuous while still pressing shutter release.
Continuous with AF
Self-timer
3 Determine the image composition while looking into LCD
monitor or viewfinder and adjust the image range and size
with the
or
key.
• When the
key is pressed, the image size becomes large (Telephoto
mode). When the
key is pressed, the image range becomes wide
(Wide-angle mode).
54
4 Press the shutter-release button half-way down.
5 Press the shutter-release button full-way down to start
timer.
• While the self-timer is functioning, the self-timer lamp in the front of the camera blinks. As the time to take the picture is closer, the lamp blinks faster.
And just before taking the picture, the lamp lights up to show the time to take
a shot.
• The beep sounds at the time when the lamp blinks. (The beep can be canceled with the menu in the SETUP mode.)
• When the subject is not in the center of the frame, use the focus lock function.
(See page 39.)
• After taking the self-timer shot, the single-shot mode returns.
* Do not press the shutter-release button when standing in front of the camera. The camera cannot
adjust the focus.
* To interrupt the self-timer shot, rotate the function dial to
, PC or SETUP.
55
ISO SETTING
Select the camera's sensitivity to light.
ISO is the standard used to indicate film sensitivity.Raising the ISO sensivity will mean that the camera needs less light in order to take an image.However,the higher the ISO value is,the grainier the
image will be.
AUTO
1 Turn on the camera,rotate the function dial to
MENU button.
2 Select the desired ISO value by pressing
default is AUTO.
/
,and press
key. The
3 Press
key to confirm the setting and press MENU button
to quit the setting.
56
EXPOSURE COMPENSATION
This function makes the image brighter or darker by adjusting the exposure compensation value for
CCD. The bigger the exposure compensation value is, the brighter the image is and the smaller the
exposure compensation value is, the darker the image is.
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor.
2 Press the
press the
3 Press the
the
key.
or
key so that [Exposure] is highlighted and
key.
or
key so that [EV] is highlighted and press
57
4 Press the
or
key that the desired exposure compensation value and press
to finish the setting.
• The exposure compensation value from +2.0 to –2.0 can be specified by 1/3
step.
5 Press the MENU button.
• The exposure compensation value is specified and displayed on the upper
right side of the LCD monitor (see page 36).
6 Press the shutter-release button full-way down to take picture.
* To cancel the exposure compensation function, follow the operation steps described above and
specify 0 for the exposure compensation value, or turn off and on the camera again.
* When the image to be captured is whitish, increase the exposure compensation value so that the
white part can be easily represented, on the other hand, when the image to be captured is blackish
decrease the exposure compensation value so that the black part can be easily represented.
58
MOVIE CLIP SHOT
Movie clip shot
The extra function allow users to take Motion Pictures in the camera with 15fps.
1 Rotate the function dial to MOVIE CLIP mode
.
• The LCD monitor will be displayed as shown.
2 Press the shutter button once and movie clips are recorded
for as long as the available recording time allows.
• Movies clips will still be recorded if the shutter button is released.
3 If you wish to stop recording, press the shutter button again.
4 Image size and type are listed below.
-Image size :QVGA (320X240)
-File type : *.AVI
5 When the movie clip is being recorded to the CF CARD, the
Green lamp blinks. [RECORDING] message will be displayed
on the LCD monitor.
Note
• The recording may be suspended during the available recording time due to the CF CARD capacity
.
59
MOVIE CLIP PLAYBACK
1 Rotate the function dial to
.
• The image files (including movie clips) will be shown on LCD monitor.
2 Press
/
key to select the movie clip files.
• The movie clip shows the icon
on top of the LCD monitor.
3 Press
key to show the movie clip(PLAY&PAUSE).
MOVIE CLIP SETTING
1 Rotate the function dial to
and press MENU button.
• [REC.TIME](recording time)is adjustable.
2 Press
/
key so that [REC.TIME] is highlighted and press
key.
• You can select recording time from 5s~30s by 5s step.
3 Press
/
key to select the desired value and press
key.
4 Press MENU button to finish the setting after confirming.
60
VOICE RECORDING
RECORDING VOICES FOR MEMORIAL PICTURES
The function allows user to record some voices in any picture which you like.
1 Rotate the function dial to
.
• The latest image is displayed on LCD monitor.
2 Press
or
key to select the desired image to record.
3 Press
key and the sound recording indicator
displayed.
will be
• The sound is being recorded.
4 Press
key again to stop recording.
• The sound will record for 10 seconds.
61
VOICE PLAYBACK
1 Rotate the function dial to
.
• The last shot is displayed on LCD monitor.
2 Press
or
• The icon
of the image is displayed on LCD monitor.
3 Press
key for PLAY & PAUSE.
key to select the image file with voice.
• Press once: PLAY
Press once more: PAUSE
62
SPECIFYING
THE RECORDING MODE
63
SPECIFYING THE RECORDING MODE
THE RECORDING MODE MENU DISPLAY (LCD Monitor)
THE RECORDING MODE MENU ITEMS
FLASH
(For the Flash mode, see page 44)
FOCUSING
(For the Focus mode,see page 37)
ISO
(For the ISO setting,see page 56)
64
(Auto-flash)
(Fill-flash)
(Flash cancel)
(Auto-flash with red-eye reduction)
(Night mode)
Central
Spot
AUTO
ISO100
ISO200
ISO400
DRIVE MODE
(Single shot)*
(For the Drive mode, see page 52)
(Continuous shot )
(Continuous with AF)
(Self-timer shot)
IMAZE SIZE
(For the Image size ,see page 71)
QUALITY
(For the Image quality, see page 68)
WHITE BALANCE
(For the White Balance, see page 73)
FULL (2560X1920)
LARGE (1600X1200)
HALF(1280X960)
VGA (640X480)
FINE (Fine mode)
STD. (Standard mode)
ECON. (Economy mode)
A
(Auto setting)*
(Daylight)
(Light bulb)
(Fluorescent)
(Cloudy)
(WB Preset)
65
EXPOSURE
(For the Exposure compensation
see page 57)
EV
AREA
SHARPNESS
(For the Sharpness, see page 75)
FULL
CENTRAL
SPOT
HARD
NORMAL
SOFT
LCD
(For the LCD, see page 99)
DEFAULT
(For the Default, see page 77)
66
YES
NO
+2.0
+1.7
+1.3
+1.0
+0.7
+0.3
0*
-0.3
-0.7
-1.0
-1.3
-1.7
-2.0
9(bright)
8
7
6
5
4
3
2
1
0(dark)
MOVIE CLIP SHOT(For the MOVIE CLIP MODE,see page 59)
REC.TIME
30s
25s
20s
15s
10s
5s
VOICE
ON
OFF
* The settings indicated with mark are resumed when the power of the camera is turned off and on, or
when the batteries are removed and inserted, For "QUALITY" and "IMAGE SIZE", the camera
memorizes the last setting before the power of the camera is turned off or before the batteries are
removed.
67
SPECIFYING THE IMAGE QUALITY MODE
This camera has 3 image quality modes; "
"(fine), "
" (Standard) and "
" (economy).
The image quality is related to the compression ratio of the image. The compression rate is higher in
the order of "
"
"
"
"
". The higher the compression rate is, the lower the
image quality is. When you want high quality images, select "
". However, as the compression rate
is low, the number of the images to be recorded in the CF card is less than that in the "
" or "
"
mode. When you want to record images in the card as much as possible, select "
" or "
".
However, as the compression rate is high, the image quality is lower than in the "
" mode.
The compression rate, image recording format, image file size and the recordable number of the
image using the CF card of 32 MB in each
,
. and
are as follows.
The compression rate
The image recording format
(Fine)
about 1/4
(Standard)
about 1/8
(Economy)
about 1/12
Exif2.1-JPEG (DCF standards)
The image file size
about 2400KB
about 1200 KB
about 600 KB
The recordable number of
the image using the CF
card of 32 MB
about 13
about 26
about 52
* Refer to the image file size and recordable number as a guide. These vary according to the scene or subject to be
recorded.
68
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor.
2 Press the
press the
or
key so that [QUALITY] is highlighted and
key.
3 Press the
or
key so that the desired image quality mode
is highlighted and press
key to finish the setting.
• The image quality mode changes in the following order.
(Fine mode)
(Standard mode)
(Economy mode)
69
5 Press the MENU button.
• The selected image quality mode is specified and displayed on the upper
left side of the LCD monitor (see page 36).
* It does not matter if there are images recorded in different image quality modes in one CF card.
* The setting of the image quality mode is stored in the camera’s memory even after the camera is
turned off.
* Changing the image quality mode affects the remaining number of images which can be recorded in
the card. Selecting " ", in particular, may considerably reduce the remaining number of image.
We recommend you to check the number display of recordable remaining flame on the data panel.
70
SPECIFYING THE IMAGE SIZE MODE
Before taking pictures, select the image size. Changing the image size affects the number of the
image which can be recorded in the CF card. The " FULL " " LARGE " " HALF " or VGA size can be
selected.
Image Size
FULL
LARGE
HALF
VGA
Number of Pixels (W x H)
2560X1920
1600X1200
1280X960
640X480
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is display on the LCD monitor.
2 Press the
press the
or
key so that [IMAGE SIZE] is highlighted and
key.
71
3 Press the
or
key so that the desired image size mode
is highlighted and press the
key.
• The image size mode changes in the following order.
FULL (2560X1920)
LARGE (1600X1200)
HALF (1280X960)
VGA (640X480)
5 Press the MENU button.
• The selected image size mode is specified and displayed under the image
quality on the upper left side of the LCD monitor (see page 36).
* The setting of the image size mode is stored in the camera’s memory even after the camera is
turned off.
* Changing the image size mode affects the remaining number of images which can be recorded in
the card. We recommend you to check the number display of recordable remaining frame on the
data panel when you change the image size mode.
72
SPECIFYING THE WHITE BALANCE MODE
This camera has 6 white balance modes.
Auto white balance
AUTO
It adjusts white balance according to light source incident on the CCD in normally.
Daylight mode
Select this mode when taking the picture of the subject illuminated by a sunlight.
Light bulb mode
Select this mode when taking the picture of the subject illuminated by an incandescent
light or tungsten light.
Fluorescent mode
Select this mode when taking the picture of the subject illuminated by a fluorescent light.
Cloudy mode
Select this mode when taking the picture of the subject under cloud.
WB Preset mode
Select this mode by using the WB preset white balance setting.
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor.
2 Press the
or
ed and press the
key so that [White Balance] is highlightkey.
73
3 Press the
or
key so that the desired white balance
mode is highlighted, press
key.
• The white balance mode changes in the following order.
A (Auto white balance)
Daylight mode
Light bulb mode
Fluorescent mode
Cloudy mode
WB Preset mode
4 Press the MENU button.
• The selected white balance mode is specified and the icon of the selected
white balance mode is displayed on the left side of the flash mode on the
upper right side of the LCD monitor (see page 36).
74
SPECIFYING THE SHARPNESS MODE
This camera has three sharpness modes as described below.
HARD
NORMAL
SOFT
This enhances the sharpness of image.
No effect of sharpness.
This reduces the sharpness of image and makes an image soft.
1 Rotate the function dial to
and press the MENU button.
• The recording mode menu is displayed on the LCD monitor.
2 Press the
or
and press the
key so that [SHARPNESS] is highlighted
key.
75
3 Press the
or
highlighted.
key so that the desired [sharpness] is
• The sharpness mode changes in the following order.
HARD
NORMAL
SOFT
4 Press the
key.
5 Press the MENU button.
• The selected sharpness mode is specified and there would be no icon
displayed on the LCD monitor. However, even if "HARD" or "SOFT" is
selected.
76
RESETING TO THE RECORDING MODE DEFAULT SETTINGS
This allows you reset this camera’s RECORDING MODE to the default at a time.
The camera settings
Flash
Focus-mode
Focus-Area
Drive Mode
Image size
Quality
White Balance
The default settings
Autoflash with red-eye reduction
Auto
Central region
Single
Full(2560x1920)
Standard
Auto
Exposure-EV
Exposure-Area
Sharpness
LCD
0
Central region
Normal
5
77
1 Press the or
press
key.
2 Press the
key.
key so that [DEFAULT] is highlighted and
key so that [YES] is highlighted and press
• The camera settings are reset to the default.
•The LCD monitor display return to the recording mode menu.
78
PLAYBACK MODE
79
SINGLE-FRAME PLAY
The images recorded in the CF card can be displayed by one frame on the LCD monitor.
1 Rotate the function dial to
.
• The function dial can be rotated even when the camera is turned on.
2 When the camera is not turned on, slide the power switch to
turn on the camera.
• The power switch returns to the initial position.
• In a while , the latest image (last recorded) is displayed on the LCD monitor.
3 Press
or
key to display the desired image.
• When the key is pressed, the following image is displayed. When the
key is pressed, the preceding image is displayed.
• When the latest image (last recorded) is displayed and the
key is
pressed, the oldest image (first recorded) is displayed.
• When the oldest image (first recorded) is displayed and the
key is
pressed, the latest image (last recorded) is displayed.
80
THE PLAYBACK MODE DISPLAY ON THE LCD MONITOR
THE PLAYBACK MODE DISPLAY ON THE LCD MONITOR
Each time the display button is pressed, the display on the LCD
monitor changes in the following order.
Single-frame play
(with the image information)
Index
(9 frames)
Single-frame play
(with no image information)
81
THE IMAGE INFORMATION DISPLAY IN THE PLABACK MODE
Frame number of the image/Total frame
number recorded in the CF card
Recorded date and time of the image
82
When the camera enters the index play mode, the
frame number of the image displayed last in the single-frame play mode is highlighted. (The frame is the
last displayed image in the figure above.)
INDEX PLAY
This mode allows you to display 9 frames at a time on the LCD monitor. It is convenient when you
search the desired image quickly.
1 When the camera is set to the single-frame play mode,
press the display button
once or twice (see page 81).
• When the image information is displayed in the single-frame play mode,
press the display button
twice and when no information is displayed,
press the display button once.
• The frame number of the image displayed last in the single-frame play mode
right before switching to the index play mode is highlighted. The other frame
numbers are displayed white on the images.
83
2 Press
key to select the desired image.
• When the
key is pressed, the following image is selected and the frame
number of the image is highlighted. When the
key is pressed, the preceding imaged is selected and the frame of the image is highlighted.
• When the ninth frame is selected (when the number 9 is highlighted) and the
key is pressed, the following 3 frames are displayed.
• When the tenth frame is selected (when the number 10 is highlighted) and
the
key is pressed, the preceding 3 frames are displayed.
3 Press the display button
once (see page 81).
• The display on the LCD monitor switches to the single-frame play mode
(with the image information) from the index play mode.
• Then selected index image (whose frame number is highlighted) is displayed in the single-frame play mode.
84
ZOOM PLAY
This mode allows you to increase the magnification of image around the center 2.0 times and display
it on the LCD monitor. It is convenient when checking the details of the image.
1 Rotate the function dial to
and press the MENU button.
• The playback mode menu is displayed on the LCD monitor
2 Press the
or
3 Press the
key.
key so that "ZOOM" is highlighted.
• The center part of the image selected in the single-frame play is magnified
2.0 times.
85
4 Press the
,
,
or
key to scroll the magnified
image.
• The image moves slightly in the direction of the key you press. The image
keeps moving while the key is held and pressed.
5 To cancel the zoom play mode, press the MENU button.
• When the zoom play mode is switched from the single-frame play mode, the
single-frame play (with the image information) mode returns.
* In the zoom play mode, the image around the center is displayed in 640 x480 pixels on the LCD
monitor.
86
SLIDE SHOW
The images can be played back continuously on the LCD monitor like an automatic slide show.
TO START THE SLIDE SHOW
1 Rotate the function dial to
and press the MENU button.
• The play back mode menu is displayed on the LCD monitor.
2 Press the
and press
or
key.
3 Press the
or
press the
key.
key so that [SLIDE SHOW] is highlighted
key so that [START] is highlighted,and
• The slide show starts according to the settings in the slide show mode menu
(the settings of "TIME" and "DIRECTION").
87
TO STOP THE SLIDE SHOW
Press one of the following buttons or keys while the slide
show is performed. The slide show stops temporarily.
• the
key
• MENU button
• When the ENTER button is pressed while the slide show stops temporarily,
the slide show stop.
• When the MENU button is pressed while the slide show stops temporarily,
the playback mode menu is displayed on the LCD monitor.
88
THE SETTING IN THE SLIDE SHOW MODE MENU
1 Rotate the function dial to
2 Press the
and press
and press the MENU button.
or
key so that [SLIDE SHOW] is highlighted
key.
3 Press the
or
press
key.
4 Press the
or
highlighted.
key so that [TIME] is highlighted, and
key so that the desired interval time is
89
5 Press the
key to finish the setting.
6 Press the
and press
or
key so that [DIRECTION] is highlighted
key.
7 Press the
or
key so that the desired direction is highlighted and press
to finish the setting.
• The direction changes in the following order.
8 Press the
slide show.
key to start
FORWARD
BACKWARD
90
DELETING IMAGES
91
DELETING SELECTED IMAGES
The images recorded in the CF card can be deleted by an image while checking them displayed on
the LCD monitor.
CAUTION
The deleted image cannot be recovered, BE CAREFUL when deleting an image.
1 Rotate the function dial to
.
• The function dial can be rotated even when the camera is turned on.
2 When the camera is not turned on, slide the power switch to
turn on the camera.
• The power switch returns to the initial position.
• In a while, the latest image (recorded last) is displayed on the LCD minitor.
3 Press
or
key to select the image to be deleted.
• When the
key is pressed, the following image is selected. When the
key is pressed, the preceding image is selected.
92
4 Press the MENU button.
• The playback mode menu is displayed on the LCD monitor
5 Press the
the
key.
or
6 Press the
press the
or
key so that [SELECT IMAGE] is highlighted,
key.
key so that [DELETE] is highlighted, press
* The color of the background in the left figure is gray so that you can easily
find out the contents of the display. However, the image to be deleted (the
image displayed on the LCD monitor in step 1 ) is actually displayed in the
background.
93
7 Press the DISPLAY button
delete.
• After pressing the
be delete.
to determine the image to
key it would show the sign that means the image will
8 Press the ENTER button so that [YES] is highlighted, and
press
key to finish the Deleting.
• "Delete selected image?" is displayed on the lower of the monitor.
9 To complete the operation of deleting an image, after confirming that [NO] is highlighted in the display to confirm,
press the
key.
• The LCD monitor display returns to the playback menu.
1 0 Press the MENU button.
• The LCD monitor display returns to the playback mode.
94
DELETING ALL IMAGES
All images recorded in this folder can be deleted.
CAUTION
The deleted image cannot be recovered, be careful when deleting all images.
1 Rotate the function dial to
.
• The function dial can be rotated even when the camera is turned on.
2 When the camera is not turned on, slide the power switch to
turn on the camera.
• The power switch returns to the initial position.
• In a while, the latest image (recorded last) is displayed on the LCD monitor.
3 Press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
95
4 After confirming that [DELETE] is highlighted, press the
key.
5 Press the
press the
key so that [ALL IMAGES] is highlighted and
key.
• The display to confirm whether you delete all images or not appears as shown
in the figure.
• Only the images captured with this camera can be all deleted. Even if you
insert the CF card in which the images captured with other camera is recorded, the images cannot be deleted.
6 Press
key so that [YES] is highlighted and press
finish the Deleting.
key to
• All images recorded in the CF card are deleted.
• While all images are deleted, the focus lamp (green) blinks slowly (about two
times a second).
96
DELETING FOLDERS
Delete the folder and all images in the folder
CAUTION
The deleted folder cannot be recovered, be careful when deleting any folder.
1 Rotate the function dial to
.
• The function dial can be rotated even when the camera is turned on.
2 When the camera is not turned on, slide the power switch to
turn on the camera.
• The power switch returns to the initial position.
• In a while, the latest image (recorded last) is displayed on the LCD monitor.
3 Press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
97
4 After confirming that [DELETE] is highlighted, press the
key.
5 Press the
the
key.
key so that [FOLDER] is highlighted and press
6 Press
/
key to choose which Folder in the CF card
want to delete, press
key.
7 Press
key so that [YES] is highlighted and press
key to
finish the Deleting.
• All images in the folder and the folder are deleted.
• While all images are deleted, the focus lamp (green) blinks slowly (about two
times a second).
• Or select [NO] to quit the deleting.
98
ADJUSTING THE BRIGHTNESS OF THE LCD MONITOR
This allows you to adjust the brightness of the LCD monitor according to the angle at which you watch
it or the brightness around the monitor so that the display on the LCD monitor can be seen clearly.
1 Rotate the function dial to
and press the MENU button.
2 After confirming that [LCD] is highlighted, press the
key.
• If the LCD monitor is turned off, the LCD monitor is automatically turned on
the live view screen and display to change the brightness of the LCD
monitor appear.
3 Press the
or
lighted. press
key so that the desired brightness is highkey to set the value you changed.
• The brightness can be adjusted in the range from 0 to 9. The smaller the
number is darker and the larger number is brighter on the LCD monitor.
* The color of the background in the left figure is gray so that you can easily
find out the contents of the display. However, the live view screen is actually
displayed in the background.
99
SPECIFYING
THE PLAYBACK MODE
100
THE PLAYBACK MODE MENU
THE PLAYBACK MODE MENU (LCD Monitor)
THE PLAYBACK MODE MENU ITEMS AND EACH SETTINGS
DELETE
SELECT IMAGE
(For deleting images
see page 92)
YES
NO
DELETE ALL IMAGES
ZOOM
FOLDER
YES
NO
YES
NO
(For the zoom play
mode, see page 85)
SLIDE SHOW
START
(For the slide show
mode,see page 87)
DIRECTION
FORWARD
BACKWARD
TIME
2-10 SEC
101
PRINT
(For specifying the
print settings
with the DPOF, see
page103)
FOLDER
(see page 110)
LCD BRIGHT
(For adjusting the brightness
of the LCD
monitor, see page 99)
STD.
INDEX
CANCEL
NEW
SELECT
CD5330
Other folder name
9(bright)
8
7
6
5
4
3
2
1
0(dark)
* For "DELETE" (deleting images), see page 92. For "ZOOM" (zoom play), see page 85. For "SLIDE SHOW" (auto
play), see page 87 Only the 2 items of "PRINT" (Specifying the print setting with DPOF), "FOLDER" (Folder
name) are described on the following pages.
102
SPECIFYING THE PRINT SETTINGS WITH THE DPOF
This camera supports the DPOF™ (Digital Print Order Format) Version 1.10 so that you can specify
the images and the number of copies to be printed and the print type. So, the specified images can be
printed at the specified number only by handing the CF card or the SmartMedia™, etc. in which not
only the captured images but the DPOF data are recorded, to the photo finishing print service supporting the DPOF. You do not need to give them the file name or your password. Also, if you set the
media including the DPOF data in the personal printer which supports the DPOF, you can print the
specified images at the specified number automatically.
* The DPOF is jointly developed by Eastman Kodak Company, Canon Inc., Fuji Photo Film co., Ltd.,
and Matsushita Electric Industrial Co., Led. for direct printing from digital camera.
SPECIFYING THE IMAGE AND THE NUMBER TO BE PRINTED
1 Rotate the function dial to
and press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
2 Press the
and press
or
key so that [PRINT] is highlighted
key.
103
SPECIFYING THE IMAGE AND THE NUMBER TO BE PRINT
3 Press the
or
press
key.
4 Press
or
key so that [STD] is highlighted and
key to select the image to be printed.
• When the image to be printed is selected, the number to be printed is highlighted.
• The sixth frame is selected and the
key is pressed, the following 3
frames are diaplayed.
• When the seventh frame is selected and the
key is pressed, the preceding 3 frames are displayed.
104
5 Press the
• When the
When the
or
key to select the number to be printed.
key is pressed, the number becomes large.
key is pressed, the number becomes small.
6 Repeat step 4 and 5 to specify the number to be printed
for all images.
• For the image you do not want to print is specify 0.
7 Press the ENTER button to finish the setting.
• The DPOF file including data of the image and the number to be printed is
recorded in the CF card.
• After the file is recorded, the LCD monitor display returns to the PLAYBACK
mode menu.
8 Press the MENU button.
• The LCD monitor display returns to the PLAYBACK mode.
105
SPECIFYING THE INDEX PRINT SETTING
This setting allows you to print all images recorded in the CF card on one sheet as an index print.
The illustration of index print as an image.
1 Rotate the function dial to
and press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
2 Press the
press
or
key so that [PRINT] is highlighted and
key.
3 Press the
key so that [INDEX] is highlighted and press
key to finish the setting.
• The display to confirm whether you print the images as an index print or not
appears as shown in the figure.
106
• The DPOF file including data of the index print setting is recorded in the CF
card.
• After the file is recorded, the LCD monitor display returns to the playback
mode menu.
4 Press the MENU button.
• The LCD monitor display returns to the playback mode.
107
TO CANCEL THE PRINT SETTINGS WITH THE DPOF
All Print settings with the DPOF described on page 103 can be cancelled. The index print setting (see
page 106) is also cancelled.
1 Rotate the function dial to
and press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
2 Press the
or
press
key.
3 Press the
press the
key so that [PRINT] is highlighted and
key twice so that [CANCEL] is highlighted and
key to finish the setting.
• The display to confirm whether you cancel all print settings or not appears as
shown in the figure.
108
FOLDER NAME
The folder in the CF card is conformed with DCF (Design rule for Camera File system) format.
When taking a picture with this camera, the "Dcim" folder is made in the directory of the CF card and
the "CD5330" folder is made in the "Dcim" folder. The first captured image is recorded with the file
name of "SIMG001.jpg" in the "CD5330"folder. The name of the folder in which the captured images
are recorded is displayed on the playback mode menu.
The file name of the image to be recorded consists of "SIMG", "4-digit number" and ".jpg". The
files are recorded in the "CD5330" folder until the
4-digit number becomes 9999 (the file mane of
"SIMG9999.jpg"). When the10000th file is recorded, the "101MX520" folder is newly made in the
"Dcim" folder and the 10000th file is recorded
with the file name of "SIMG0001.jpg"in the
"101MX520"folder.
There will be two folders for the images in one CF card if you capture more than 10000 images. You
can select the folder in which the image to be played back is recorded by the folder name displayed in
the playback mode menu.
Continued on Next page 109
SELECTED A FOLDER
Even if other digital camera supporting the DCF format is used to record the captured images in the
CF card, you can insert the CF card into this camera and play back the images by selecting the particular folder name of other digital camera in the playback mode menu.
1 Rotate the function dial to
and press the MENU button.
• The playback mode menu is displayed on the LCD monitor.
2 Press the
or
press
key.
key so that [FOLDER] is highlighted and
3 Press the
or
press
key.
key so that [SELECT] is highlighted and
•The existence folder is displayed on the LCD monitor.
• After chose the folder, the following images will be saved in the selected folder.
110
GIVE THE FOLDER A NEW NAME
You could give the folder a new name in the FOLDER-NEW mode, determine the last 5 character arbitrary.
1 Rotate the funtion dial to
and press the MENU button.
•The playback mode menu is displayed on the LCD monitor.
2 Press the
or
press
key.
3 Press the
key.
or
key so that[FOLDERS] is highlighted and
key so that [New] is highlighted and press
111
4 Press
or
key select the character you like and press
the
key to determine.
•If you won't give a new name, press the menu button back to playback menu.
5 Press the
key so that the folder name in which the
image to be played back is recorded is highlighted and
press the ENTER button.
• When only "CD5330" folder exists, the folder name does not change even
the
or
key is pressed.
112
On DCF (Design rule for Camera File system) Format
DCF (Design rule for Camera File system) is the image format established by JEODA as the standard format of digital camera.
Through this format, the image files can be used between the digital equipment conformed to DCF.
The following operation can be available between the digital equipment conformed to DCF:
• The images captured with your digital camera can be played back on the LCD monitor of other
digital camera.
• The images captured with some digital cameras can be printed out from a printer.
• A recording media (such as a CF card or SmartMediaTM) can be used with any of the digital
cameras.
• By using the computer conformed to DCF, even the image data recorded with some digital cameras can be easily sorted out.
113
SETUP
114
THE SETUP MODE MENU DISPLAY
THE SETUP MODE MENU DISPLAY ON THE LCD MONITOR
FORMAT
(For formatting the CF
card, see page 119)
NO
YES
POWER SAVE
(For the time for the auto power off
function, see page 117)
1 min. (1 minute)
3 min. (3 minutes)
5 min. (5 minutes)
10 min. (10 minutes)
30 min. (30 minutes)
115
DATE/TIME
DATE
YY/MM/DD
(For setting or correcting
the date and time, see
page 121)
TIME
HH:MM
BEEP
(For turning on or off the beep, see page 123)
ON (The beep sounds.)
OFF (The beep does not sound.)
VIDEO OUT
(For switching the video signal from the video-out terminal, see page 125)
PAL
NTSC
LANGUAGE
ENGLISH
GERMAN
(For switching the language displayed on the LCD monitor, see page 127)
DEFAULT
(For resetting the camera, see page 128)
116
NO
YES
SPECIFYING THE TIME FOR THE AUTO POWER OFF FUNCTION
To save the battery power, this camera will be turned off automatically if it is not operated more than 5
minutes. (Auto Power Off function) The time for the auto power off function is set to 5 minutes unless
you change the setting after you purchase this camera.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The power switch returns to the initial position.
2 Press the
button.
• The setup mode menu is displayed on the LCD monitor as shown in the
figure.
3 Press the
or
ed and press the
key so that [POWER SAVE] is highlightkey.
117
4 Press the
or
key so that the desired time for the
auto power off function is highlighted.
• The time for the auto power off function changes in the following order.
1 min. (1minute)
3 min. (3 minutes)
5 min. (5 minutes)
5 Press the
setting.
key to finish the
10 min. (10 minutes)
30 min. (30 minutes)
´Only when using the batteries, the time for the auto power off function can be specified. When using
the AC adapter (sold separately), the time for the auto power off function is fixed in 30 minutes and
cannot be changed.
´When this camera is connected to the computer , the time for the auto power off function is fixed 30
minutes automatically regardless of the setting or the power supply.
118
FORMATING THE CF CARD
This allows user to format the CF card.
CAUTION
As all the images recorded in the CF card are deleted and cannot be recovered, be careful when
formatting the CF card.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The power switch returns to the initial position.
2 Press the
button .
• The setup mode menu is displayed on the LCD monitor as shown in the figure.
3 Press the
or
press
key.
key so that [FORMAT] is highlighted and
• The display to confirm whether you format the CF card or not appears.
119
4 Press the
key so that [YES] is highlighted and press the
Key to finish the setting.
• The format of the CF card starts.
• After formatting the CF card, the LCD monitor returns to the setup mode
menu display.
120
SETTING THE DATE / TIME
When taking a picture, the date and time are recorded as the part of the image information. If the
built-in clock of this camera is not set correctly, the wrong date and time ate recorded. Set the date
and time correctly by performing the procedure below.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The power switch returns to the initial position.
• The setup mode menu is displayed on the LCD monitor as shown in the
figure.
2 Press the
or
and press the
key so that [DATE/TIME] is highlighted
key.
• The display to set the date and time appears as shown in the figure.
3 Press the
press the
or
key so that [DATE] is highlighted and
key.
121
4 Press the
or
key to specify or correct the date and
press
key to finish the setting.
• When you press and hold the
fastbackward.
5 Press the
and press
or
key.
or
key, the value goes fastforwrd or
key so that [DATE/TIME] is highlighted
• The display to set the date and time appears as shown in the figure.
6 Press the
press the
or
key so that [TIME] is highlighted and
key.
7 Press the
press the
or
key to specify or correct the date and
to finish the setting.
• When you press and hold the
or fastbackward.
122
or
key, the value goes fastforward
SETTING THE BEEP SOUND
The beep sounds each time you operate this camera with the buttons or function dial and you can
turn off or on the beep. The beep is turned on unless you change the setting after you purchase this
camera.
When you use this camera in the situation you cannot make noise such as a wedding ceremony, etc.,
you can turn off the beep.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The power switch returns to the initial position.
• The setup mode menu is displayed on the LCD monitor as shown in the
figure.
2 Press the
press the
or
key so that [BEEP] is highlighted and
key.
123
3 Select [ON] or [OFF] with the
or
key.
• The setting of the beep changes in the following order.
ON (The beep sounds.)
OFF (The beep does not sound.)
4 Press the
key to finish the setting .
• When [OFF] is selected on step 4 , the beep does not sound even when
you operate with the buttons or the function dial.
• The volume of the beep cannot be changed.
124
SWITCHING THE VIDEO SIGNAL FROM THE VIDEO OUTPUT TERMINAL
As this camera has the video-out terminal, you can watch the captured images on TV by connecting
this camera to your TV with the supplied video cable.
The video output signal can be switched between NTSC and PAL.
What is an NTSC system and a PAL system?
Both are the color television broadcast system. The NTSC system is mainly used in U.S.A., Japan, Canada,
Mexico, the Philippines, Korea, etc. The PAL system is used in the western Europe such as Germany, England,
Switzerland, Netherlands, Italy (except for France) and Australia, Singapore, Thailand, China, etc.
As these systems have no compatibility, you cannot watch the NTSC system based TV in the area where a PAL
system is used.
This camera can switch the video output signal to both an NTSC system and a PAL system. So you can watch the
images on TV not only in your country, but in other areas.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The power switch returns to the initial position.
• The setup mode menu is displayed on the LCD monitor.
2 Press the
or
and press the
key so that [VIDEO OUT] is highlighted
key.
125
3 Select [PAL] or [NTSC] with the
or
key.
• The setting of the beep changes in the following order.
PAL
NTSC
4 Press the
key to finish the setting.
• The video signal system output from the video-out terminal is switched to
the selected one.
126
SWITCHING THE LANGUAGE DISPLAYED ON THE LCD MONITOR
The language displayed on the LCD monitor can be switched to English.
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The setup mode menu is displayed on the LCD monitor as shown in the figure.
2 Press the
or
and press the
key so that [LANGUAGE] is highlighted
key.
3 Select [ENGLISH] with the
or
key.
• The language changes in the following order.
4 Press the
key to finish the setting.
• The language on displayed on the LCD monitor is switched to the selected
one.
127
RESETTING TO THE DEFAULT SETTINGS
This allows you reset all this camera's PLAYBACK MODE, SETUP MODE, PC MODE to the default
at a time.
The camera playback settings
The default playback settings
Delete (see page 92)
Selected Image
Slide show-Time (see page 89)
2 sec
Slide show-Direction (see page 87)
Forward
Print(see page 103)
STD (standard)
Folders(see page 109)
CD5330
LCD(see page 99)
5
The Camera Setup settings
Power save (see page 117)
Beep sound (see pages 123)
The Camera pc setting
PC connection
128
The default setup settings
3 minutes
On
The default pc settings
Storage
1 Rotate the function dial to "SETUP" and slide the power
switch to turn on the camera.
• The setup mode menu is displayed on the LCD monitor as shown in the
figure.
2 Press the
or
and press the
key so that [DEFAULT] is highlighted
key.
• The display to confirm whether you reset the camera settings to the
default or not appears as shown in the figure.
3 Press the
or
key so that [YES] is highlighted and press
key to finish the setting.
• The camera settings are reset to the default.
• The LCD monitor display returns to the setup mode menu.
129
CONNECTING TO
THE PERSONAL COMPUTER
130
INSTALLATION OF THE DRIVER AND APPLICATION SOFTWARE
INSTALLATION OF THE DRIVER SOFTWARE
The following operation is required for Windows®98 .
ATTENTION WINDOWS 98 USERS:
Please follow steps 1-10.
ATTENTION WINDOWS 2000, ME, XP USERS:
Please follow steps 6-10 after inserting the CD-ROM in the CDROM drive in your computer. It is not necessary to install the
driver. It is only necessary to install DirectX and ArcSoft software. Please refer to pages [ p133-140 ] to begin the installation.
1. Insert installation CD-ROM.
2. Press "Driver" button.
131
INSTALLATION OF THE DRIVER AND APPLICATION SOFTWARE
3. Press "Next"..
4. Starting install driver.
5. Press "Finish " to complete installation.
132
INSTALLATING MICROSOFT DIRECTX 8.1
6. Press "Yes" to install DirectX 8.1.
Important:
DirectX 8.1 enables the movie playback applications on your computer
to play movie clips that are captured with the Concord Eye-Q 5330z.
(e.g. Windows Media Player)
7. Press "Yes".
8. Starting install DirectX 8.1.
133
INSTALLATION OF THE DRIVER AND APPLICATION SOFTWARE
9. Press "OK" to complete installation.
10. Restart your computer.
134
INSTALLATION PHOTOIMPRESSION
For all Windows users.
1. Insert installation CD-ROM.
2. Press "Application" to install ArcSoft PhotoImpression.
3. Press "Next" to continue install PhotoImpression.
4. Press "Next".
135
INSTALLATION PHOTOIMPRESSION
5. Press "Next".
6. Press "Next".
7. Press "Next".
136
INSTALLATION PHOTOIMPRESSION
8. Starting set up.
9. Press "Finish" to complete installation.
137
INSTALLATION VIDEOIMPRESSION1.6
1. Press "Application" to install ArcSoft VideoImpression.
2. Select language that you want and press "sure"
3. Preparing set up.
4. Press "Next".
138
INSTALLATION VIDEOIMPRESSION1.6
5. Press "Yes".
6. Press "Next" to choose folder which you will save.
7. Press "Next".
139
INSTALLATION VIDEOIMPRESSION1.6
8. Press "Next".
9. Starting install VideoImpression1.6.
10. Press "Finish" to complete installation.
140
For Apple Macintosh (OS9, OS10)
INSTALLATION DRIVER
Do not need to install driver.
INSTALLATION PHOTOIMPRESSION
1. Insert installation CD-ROM.
2. Click "ARCSOFT" to install PhotoImpression.
3. Click "PhotoImpression3" to set up software .
141
For Apple Macintosh (OS9, OS10)
4. Click language that you want.
5. It will show below screen and click "PhotoImpression
Installer".
6. Press "Accept".
142
For Apple Macintosh (OS9, OS10)
7. Press "Install" to start installation.
143
INSTALLATION VIDEOIMPRESSION1.6
1. Click "Video Impression1.6" to set up software.
2. Select language that you want.
3. It will show the below screen and click
"VideoImpression1.6 Installer".
144
INSTALLATION VIDEOIMPRESSION1.6
4. Press "Accept".
5. Click "Install" to start installation.
145
CAUTIONS WHEN CONNECTING TO THE PERSONAL COMPUTER
• While this camera is connected to the computer or transferring the image data between this camera
and the computer, do not perform the following operations. Otherwise, the error may occur, the
camera and the computer may not function correctly, or the image data recorded in the CF card
may be erased or damaged.
• Turn off the power of the camera
• Disconnect the USB cable
• Rotate the function dial
• Remove or insert the CF card
• When the camera is connected to the computer. The time for the auto power off function is fixed in
30 minutes automatically regardless of the power supply you use or the settings un the SETUP
mode (see page 113).
146
CAUTIONS WHEN CONNECTING TO THE PERSONAL COMPUTER
• When connecting the camera to the computer and transferring the image data between them, be
sure to check that the battery capacity is full. If the battery power is low, the power of the camera
may be turned off while transferring data. If this happens, the error may occur, the camera and the
computer may not function correctly, or the image data recorded in the CF card may be erased or
damaged.
When the camera is connected to the computer, we recommend you to use new batteries with a full
power capacity or the AC adapter (sold separately).
147
Requirements of PhotoImpression & VideoImpression
To use the supplied image editing application PhotoImpression and VideoImpression, the following
systems are required.
For the IBM-PC/AT and the compatible unit
CPU
OS
Memory
Hard disk space
Monitor
CD-ROM drive
Intel Pentium II processor of 233 MHz or more, or the
computer equipped with the fully compatible processor.
Windows®98/98SE/ME/2000/XP
Windows® NT 4.0 (Service Pack 5)
16 MB or more of built-in memory (For Windows® NT,
32 MB or more of built-in memory).
110 MB or more of available hard disk space.
Resolution 800 x 600/th color monitor for 16-bit color video display
Necessary (when installing and using the software).
For Apple Macintosh
CPU
68040 or later processor or better, or Macintosh or Power
Macintosh
OS
Mac OS9, OS10.1
Memory
32MB RAM or higher
Hard disk space
Monitor
CD-ROM drive
148
110 MB or more of available hard disk space.
The color monitor capable of displaying 256 colors
Necessary (when installing and using the software).
APPENDIX
149
WATCHING THE CAPTURED IMAGES ON TV
WATCHING THE CAPTURED IMAGES ON TV
By connecting this camera to your TV with the supplied video cable, you can watch the captured
images on TV.
1.Confirm that the video out signal from the video-out terminal is set to NTSC or
PAL according to the color system in your country. ( see page 125 ).
2.Turn off the power of the this camera and TV.
3.Open the terminal cover on the left side of the camera and connect the mini
plug of the supplied video cable to the video-out terminal of the camera.
• The LCD monitor is turned off.
4.Connect the other side of the video cable to the video input terminal on TV.
5.Turn on the power of TV.
6.Rotate the function dial to
7.Slide the power switch to turn on the camera.
8.Switch the video input of TV according to the terminal to which the video
cable is connected.
• The images recorded in the CF card can be displayed both on the LCD monitor and TV.
9.You can watch the images in the various play modes following the procedure .
• The images can be played back in the slide show mode ( see page 82 ) , etc.
150
TROUBLESHOOTING
If you have any trouble with this camera, check the following items.
Problem
The focus cannot be
adjusted in the autofocus mode The focus
lamp (green) blinks
quickly (about 8 times
in a second) when the
shutter-release button
is pressed half-way
down.
Check
Do you attempt to adjust the focus
on the subject, which is difficult to
focus in the autofocus mode?
Do you attempt to take a picture
when the subject is closer than the
minimum focus distance (40 cm),
or farther than 40 cm in the close
up mode?
Is the power of the camera
turned off?
Is the camera set to other
The shutter-release
mode except the recording
button is not released.
mode?
Is the focus lamp (green)
blinks slowly (about 2 times in
a second) and "Recording"
blinking on the LCD monitor?
Solution
Take a picture with the focus lock
function or in the manual focus
mode.
Take a picture when the subject is
farther than 40 cm, or when the
subject is within the distance from 8
cm to 40 cm (is not apart more than
40 cm from the camera) in the
close mode.
Rotate the function dial to
and slide the power switch to turn
on the camera.
Page
39
40
41
33
The image is recorded in the CF
35
card. Wait until the recording is
completed and the focus lamp
(green) and "Recording" stop blinking.
151
Problem
Check
The shutter- Is "CARD FULL" displayed on the
release button LCD monitor?
is not
released.
Is the power of the camera turned
off?
The live view Are the batteries exhausted?
is not displayed on the Are the batteries inserted with the
LCD monitor. correct polarity?
Solution
Page
The CF card is full. Delete unwanted
images or transfer the image data to
92
the computer and then delete all
images, or use other CF card, which
has a memory space.
Rotate the function dial to
and slide 33
the power switch to turn on the camera.
Replace all four batteries or use the AC
adapter (sold separately).
Remove the batteries and then insert
the batteries by following the +/- diagram indicated in front of the batterychamber door.
Is the LCD monitor turned off?
Press the display button to turn on the
monitor.
The auto power off function activates. Slide the power switch to turn on the
camera again.
152
27
28
25
35
25
Problem
Check
Is the power of the camera
turned off?
Are the batteries exhausted?
Solution
Rotate the function dial to
and slide the power
switch to turn on the camera.
Replace all four batteries or use the AC adapter
( sold separately ).
Are the batteries inserted with the Remove the batteries and then insert the batteries by
The image correct polarity?
following the +/- diagram indicated in front of the batcannot be
tery-chamber door.
played
Is the CF card is inserted in the When "NO CARD" is displayed on the LCD monitor and
back on
"CF" is displayed on the data panel, the CF card is not
camera? ( Is "NO CARD" disthe LCD
set. Insert the CF card.
played on the LCD monitor? )
monitor.
The auto power off function acti- Slide the power switch to turn on the camera again.
vates.
The camera reads out the image data from the CF
Is the focus lamp ( green )
blinks slowly (about 2 times in card.
a second ) and "PLAY BACK" Wait until the reading is completed and the focus lamp
and "PLAY BACK" stop blinking.
blinks on the LCD monitor?
Theimage Did you take a picture within
Take a picture within the flash range ( 0.4 to 3 m ) .
recorded in the flash range?
the flash
mode is
dark.
Page
80
25
28
25
25
29
44
153
Problem
The zoom play
cannot be performed.
The image is too
dark or bright.
Even when the
lens comes out,
the data panel is
turned off and
the camera can
not function.
The recorded
image file is
damaged.
The camera
does not function
correctly due to
the strong static
electricity, etc.
154
Check
Solution
Did you take a picture with the digi- The picture captured with the digital zoom
tal zoom function?
function cannot be played back in the zoom
play mode.
Specify 0 for the exposure compensation
Is the exposure compensation
value.
value specified?
If the
battery-condition indicator blinks, all
Has the
battery-condition
indicator blinked (all the indicators the indicators will disappear after 5 seconds
while the lens is protruding.
disappeared after 5 seconds ) ?
Page
50
85
99
25
Did you remove the CF card when The data is being recorded in or read out from
33
the image data was recorded in or the CF card while the focus lamp ( green )
blinks slowly (about 2 times in a second ). Do
read out from the CF card?
not remove the CF card from the camera.
Remove the batteries and insert them again. When using the AC adapter ( sold
separately ) , disconnect the plug of the AC adapter from the AC outlet and then
connect it again.
After that, turn on the power of the camera.
* If the power of the camera cannot be turned off correctly, the CF card may be
damaged. In this case, transfer the image data in the CF card to the computer and
then format the CF card.
NOTES ON THE HANDLING
Batteries
• Battery performance decreases with lower operating temperatures. In a cold place, we recommend you to
prepare new batteries and keep the spare batteries in a warm place such as inside your coat.
As the performance of Ni-MH battery less decreases, we recommend you to use the Ni-MH battery in a
cold place. Even if the battery performance decreases due to a cold environment, the battery can recover
its power when the battery warms up.
• Remove the batteries when they are not in use for an extended period. The battery leakage may damage
the battery-chamber.
• Occasionally, when using alkaline batteries, the battery-condition indicator shows that the battery power is
low even if there is enough power capacity.
Continue to use the camera. The low-battery symbol will disappear.
• As the batteries heat up just after the camera is used, be careful when removing or replacing the batteries.
Turn off the power of the camera and allow the batteries to cool down.
155
LCD Monitor Care
• The LCD monitor is manufactured using high precision technology. However, there may rarely be a
lack of color or bright points on the LCD monitor.
• Do not apply pressure on the surface of the LCD monitor. Permanent damage may occur.
• In a cold environment, the LCD monitor may be temporarily dark. When the camera warms up, normal display will be restored.
• The LCD monitor may be slow to react in a low temperature or may be dark in a hot environment.
When the camera warms up, normal display will be restored.
• If there are fingerprints on the LCD monitor surface, gently wipe it with a soft, clean, dry cloth.
Copyright
• TV program, films, video tapes, and other materials may be copy righted.
Unauthorized recording of such materials may be contrary to the provision of the copyright laws.
And in some performance and exhibition, etc. taking picture are prohibited. The image which has a
copyright cannot be used except for the use within the copyright laws.
DPOF
• If the CF card including the DPOF data specified by other camera is set in this camera, the DPOF
data will be cancelled.
• Even if you insert the CF card including the data recorded with other digital camera supporting the
DCF format, the DPOF data for the images captured with other digital camera ( the images in the
folder made by other digital camera supporting the DCF format ) cannot be specified in this camera.
156
Operating Temperatures and Conditions
• This camera has been designed for use in temperatures from 0ºC to 40ºC (32ºF to 104ºF).
• Never leave the camera exposed to extreme high temperatures, such as in a car parked in the sun, or to
extreme humidity.
• To prevent condensation from forming, place the camera in a sealed, plastic bag when bringing it from a
cold place to a warm place. Allow it to come to room temperature before removing it from the bag.
Safety and Handling for the CF card
• Read and follow the instructions manual supplied with the CF card.
• The following may cause data loss or damage. We have no responsibility for it. We recommend you to
copy a backup data in other media such as ZIP disc, hard disk, CD-ROM, etc.
1 Improper use of card.
2 Static electrical discharge near card or electric noise.
3 Removing the card or interrupting power supply while camera or equipment is accessing the caed ( reading, writing, formatting etc. )
4 Non-use of card for an extended period.
5 Using the card over its life.
• When the card is formatted, the recorded data is deleted. Be sure to record a backup data if it is necessary.
• The storage capability of the CF card will diminish with extended use. In this case, buy a new card.
• Keep away from static electricity and electric noise.
• Do not bend, drop, or subject the card to impact.
• The strong static electricity or shock may damage the card so that recording or writing in the card cannot
be performed. In this case, buy a new card.
• Do not touch the electrical contacts of the card with your fingers or a metal object.
• Keep away from heat, moisture, and direct sunlight.
• Keep away from small children.
• When not in use, return the card to its protective case.
157
Others
• Do not subject the camera to shock or impact.
• Turn off the power of the camera when transporting.
• This camera is neither waterproof nor splashproof.
Inserting or removing batteries and the CF card, or operating the camera with wet hands may daage
the camera.
When using the camera at the beach or near water, take care not to drop water or sand on the camera. If water, sand, dust or salt content accumulates on the camera, it may cause the malfunction.
• Do not leave the camera under direct sunlight. Do not point the lens at direct sunlight. Doing so,
CCD may be damaged.
158
CARE AND STORAGE
Cleaning
• If the camera or the outside of the lens is dirty, gently wipe it with a soft, clean, dry cloth. If the camera or lens comes in contact with sand, gently blow away loose particles. Wiping may scratch the
surface.
• To clean the lens surface, first blow away any dust or sand, then, if necessary, moisten a lens tissue
or soft cloth with lens cleaning fluid and gently wipe the lens.
• Never use organic solvents to clean the camera.
• Never touch the lens surface with your fingers.
Storage
• Store in cool, dry and well-ventilated place away from dust and chemicals.
For very long periods, store the camera in an airtight container with a silica gel drying agent.
• Remove the batteries or the CF card from the camera when not in use for an extended period.
• Do not store the camera in the closet with mothballs.
• We recommend you to press the shutter-release button sometimes during the storage. Also, check
the camera’s operation to make sure it is functioning properly before using.
Before Important Events such as a Wedding Ceremony, Overseas Travel
• We recommend you to check the camera’s operation beforehand or take test pictures, and to prepare spare batteries.
• CONCORD has no responsibility for damages incurred by equipment malfunction.
Questions and Service
• If you have questions about your camera, contact your local camera dealer or write to the Jenoptik
distributor in your area.
159
TECHNICAL DETAILS
Camera Type
Recording media exchangeable 3X zoom digital camera with LCD monitor
CCD
Pickup elements:
1/1.8 inch-type inter line CCD, 5.13M pixels, with a base color filter
Pickup system:
single
ISO sensitivity:
AUTO ISO 100 200 400
Number of bit converted to A/D: 12 bit
Lens Unit
Focal length:
8 to 24 mm ( 34 to 102 mm in the 35 mm film format equivalent )
Aperture:
Wide: F3.37 ,F4.86 ,F7.75 ,F15.03(4steps)
Tele :F3.56 ,F5.13 ,F8.2 ,F15.4(4steps)
Construction:
9 elements in 6 groups including 3 aspheric surfaces
Focusing range:
40 cm to infinity ( The close up mode: 8 cm to 40 cm )
Digital zoom:
maximum zoom in the telephoto mode X2
Image Storage
Recording medium: CF card ( Type 1 )
Image file format:
Exit 2.1 ( JPEG ), DCF standards, DPOF 1.10
Number of pixels ( W x H ): 2560x1920 pixels ( Full size )
1600x1200 pixels ( Large size )
1280x960 pixels ( Half size )
640x480 pixels ( VGA size )
160
Technical Support Hot Line:
Toll Free In the USA & Canada
1-866-522-6372
Toll Free In Europe
UK: 0800-169-6482
BELGIUM: 0800-787-57
FRANCE: 0800-917-599
GERMANY: 0800-1800-563
SPAIN: 900-973-195
ITALY: 800-781-883
All Other Countries - Toll
31-53-482-9779
Storage capacity ( Using a 32 M B CF card ) :
FINE
STD.(Standard)
ECOn.(Econmy)
Other:
2560x1920 size
approx. 13 images
approx. 26 images
approx. 52 images
1600x1200 size
approx. 30 images
approx. 60 images
approx. 90 images
1280x960 size
approx. 50
approx. 100
approx. 175
VGA
175
290
340
The number of images to be recorded varies depending on the subject.
Delete function ( Single image. All images ) Format function for the CF Card
161
Autofocus
System:
AF system by CCD
Focus locked when the shutter-release button is pressed halfway.
Focus mode :
One shot AF
Manual Focus :
Avaliable (operated with
,
,
and
keys.)
Auto Exposure (AE) Control
Exposure mode :
Programmed AE
AE Locked when the shutter-release button is pressed halfway.
Metering :
Center weighted TTL metering
Shutter:
CCD electrical shutter (with a Mechanical shutter)
Shutter speed:1/2600 sec. to 8sec.
Exposure compensation: ± 2EV in 1/3EV increments
White balance :
Automatic, Manual setting available(outdoors,tungsten,fluorescent)
LCD Monitor
Type :
46mm (1.8-inch) TFT-LCD module
Pixels :
Approx.60,000
Bright level :
9 steps
Language display : English,German
Display :
Single frame display, index display (9 frames), slide show, magnification display,
( the zoom play, X2, changing magnification area available)
Viewfinder
Type :
Real image zoom finder
Fineld of view ( 3 m) : more than 80%
Eye-relief :
19 mm
Magnification :
X 0.35 to X 0.902(Wide:0.350x,tele:0.902x)
162
Drive Mode
Mode: Single shot, continuous shot(approx.1 frame / sec.), self-timer shot
Self-timer:
Built-in Flash
Charge time:
Flash modes:
Approx. 10 second delayed release
Approx. 8 second at fill flash
Autoflash, Fill-flash,Flash cancel, Autoflash with red-eye reduction,Fill-flash with
(Flash cancel in the close up mode),night mode.
Flash intensity control: Adjusted automatically by an external light
Interface
Video output:
Compositevideo signal,switchable between NTSC and PAL
PC interface:
USB port
Power Supply
Batteries:
AA-sized alkaline battery x 4 or AA+sized Ni-MH battery x 4(AA-sized lithium
battery is not available.)
External power:
AC adapter (not supplied) (a DC terminal is provided on the camera body.)
Operating temperature: 0 to 40ºC (32 to 104ºF)
Dimensions Weight
Dimensions(WxHxD): 116x75x62mm(4.57x2.95x2.44 inches)(not including the projecting parts)
Weight:
Approx.270.5g(9.54 oz.)(without batteries and the CF card)
Specifications are based on the latest information available at the time of printing and are subject to
change without notice.
163
164
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement