Code Code Reader 1000 User`s manual

Code Code Reader 1000 User`s manual
Bar Code Reader
Models 1000/1002
USER'S MANUAL
2190 Regal Parkway • Euless, TX 76040
(817) 571-9015 • (800) 648-4452 • FAX (817) 685-6232
FCC NOTICE
WARNING: This equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. It has been tested and found
to comply with the limits for a Class A computing device pursuant to Subpart J of
Part 15 FCC Rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures may be
required to correct the interference.
Rev 3.2c
TABLE OF CONTENTS
Introduction ......................................................................................................... 1
Installation Instructions ....................................................................................... 2
Scanning Bar Codes ........................................................................................... 5
Wand Scanning .................................................................................... 5
Slot Reader (Badge Reader) ................................................................ 6
Default Settings ................................................................................................... 7
Changing the Default Settings ............................................................................ 9
Programming Guide .......................................................................................... 11
Code 39 .............................................................................................. 12
UPC .................................................................................................... 13
EAN .................................................................................................... 14
UPC/EAN Supplements ...................................................................... 15
Interleaved 2 of 5 ................................................................................ 16
Codabar .............................................................................................. 17
Code 128 ............................................................................................ 17
Code 93 .............................................................................................. 18
MSI/Plessey ........................................................................................ 19
Code 11 .............................................................................................. 20
Preamble ............................................................................................ 21
Postamble ........................................................................................... 21
Bar Code Edit ..................................................................................... 22
Termination Character ........................................................................ 23
Beep Tone .......................................................................................... 23
Beep Length ....................................................................................... 23
Computer Type ................................................................................... 24
Transmit Speed .................................................................................. 24
Other Options ..................................................................................... 25
Diagnostics ......................................................................................... 28
Specifications .................................................................................................... 29
Signal Definitions .............................................................................................. 30
i
TABLE OF CONTENTS (Cont)
Appendix A - Function & Special Keys ........................................................ A-1
Appendix B - Code 39 Specifications .......................................................... B-1
Appendix C - Full ASCII Extension to Code 39 ........................................... C-1
Appendix D - UPC Specifications ................................................................ D-1
Appendix E - EAN Specifications ................................................................ E-1
Appendix F - Interleaved 2 of 5 Specifications ........................................... F-1
Appendix G - Codabar Specifications .......................................................... G-1
Appendix H - Code 128 Specifications ........................................................ H-1
Appendix I
- Code 93 Specifications ............................................................ I-1
Appendix J
- Sources of Bar Code Standards ............................................. J-1
ii
INTRODUCTION
The Model 1000/1002 bar code reader is an easy to use system that accepts a wand
or slot reader as an input device. The reader installs quickly between the keyboard
and personal computer. Data is sent to the computer as if it were typed in from the
keyboard. No hardware or software changes are necessary.
Tailor the reader to individual applications by simply scanning a bar code from the
menu. It’s that simple! All these features make the Model 1000/1002 an ideal data
collection device that provides quality and performance in one package.
FEATURES:
Bar Code Data Appears as Keyboard Input to the PC.
Reader Automatically Recognizes and Reads the Following
Bar Code Types:
Code 39
Extended Code 39 (Full ASCII)
Interleaved 2 of 5
UPC-A, UPC-E(0), UPC-E(1)
EAN-8, EAN-13
UPC & EAN Supplements (2 and 5 Character)
Codabar
Code 128
Code 93
Code 11
MSI/Plessey
Power/Ready Light Indicates Scanner Status.
1
INSTALLATION INSTRUCTIONS
OVERVIEW
Installation requires connecting cables between the reader and your computer.
Step 1:
Turn OFF the power to the computer.
Step 2:
Unplug the KEYBOARD cable from the back of the computer and
plug it into the connector labeled "KEYBOARD" on the rear panel
of the reader.
COMPUTER KEYBOARD
Step 3:
Plug one end of the cable (supplied with the reader) into the
connector labeled "COMPUTER" on the rear panel of the reader.
COMPUTER KEYBOARD
Step 4:
Plug the other end of the cable (supplied with the reader) into the
KEYBOARD connector located on the back of your computer.
2
Step 5: CONNECTING INPUT DEVICES:
Installing a Wand
Plug the end of the WAND cable into the circular connector labeled
"WAND" on the front panel of the reader.
MICROSCANNER
AMERICAN
MICROSYSTEMS
POWER
WAND
Installing A Slot Reader
Plug the end of the SLOT READER cable into the circular
connector labeled "WAND" on the front panel of the reader.
MICROSCANNER
AMERICAN
MICROSYSTEMS
POWER
WAND
3
Step 6: Verify that the cables are connected as shown below:
Step 7:
Turn ON the power to the computer. (The reader receives its
power from the computer just like the keyboard.)
Step 8:
The "POWER" display light on the front panel of the reader will
display RED and the reader will BEEP twice. Approximately 1/2
second later the display will change to GREEN.
Step 9:
The GREEN color indicates the reader is ready to use. The
keyboard remains fully functional and you may enter data as
before.
4
SCANNING BAR CODES
WAND SCANNING
Step 1:
HOLD THE WAND LIKE A PENCIL, tilted at an angle of 10o to 30o
from vertical.
Step 2:
TOUCH the wand tip to the WHITE SPACE before the label.
Step 3:
Move the wand QUICKLY across the label as if you were drawing a
straight line through the middle of it.
Step 4:
Begin and end your stroke in the WHITE SPACE. Maintain a
smooth, even stroke while scanning. You can read labels bidirectionally (either left-to-right or right-to-left) and the data will
output correctly to your computer.
Step 5:
If you scanned the label correctly, you will hear a short BEEP.
When the "POWER" light turns GREEN the reader is ready to scan
another label.
5
SLOT READER (Badge Reader)
Step 1:
Hold the CARD so that the bar code label is on the bottom and
FACES the ARROW on the slot reader.
Step 2:
Insert the CARD into the opening on either side of the reader.
Step 3:
Holding the CARD flat against the bottom of the reader, SLIDE the
card through the opening. You can slide the CARD bi-directionally
(either left-to-right or right-to-left) and the data will output correctly
to your computer. The CARD must maintain contact with the base
of the reader while scanning. The front panel "POWER" light will
change to RED while the card is being pulled through the SLOT
READER.
NOTE: The center of the bar code must be positioned 0.5" from
the bottom edge of the card.
Step 4:
After a successful read the following will occur:
The decoder will BEEP.
The bar code data is transmitted to the computer.
Step 5:
When the front panel "POWER" light changes to GREEN, the
reader is ready to scan another card.
6
DEFAULT SETTINGS
The Model 1000/1002 is shipped from the factory with the following default settings:
CODE 39
CODE 39 DECODER
FULL ASCII
MOD 43 CHECK DIGIT
SEND CHECK DIGIT
CONCATENATE M ODE
UPC
ON
OFF
OFF
OFF
OFF
UPC DECODER
CONVERT UPC-E TO UPC-A
CONVERT UPC-A TO EAN-13
SEND UPC-A NUMBER SYSTEM
SEND UPC-E NUMBER SYSTEM
SEND UPC-A CHECK DIGIT
SEND UPC-E CHECK DIGIT
EAN
EAN DECODER
ZERO FILL EAN-8 TO EAN-13
SEND EAN-13 COUNTRY CODE
SEND EAN-8 COUNTRY C ODE
SEND EAN-13 CHECK DIGIT
SEND EAN-8 CHECK DIGIT
ISBN CONVERSION
UPC/EAN SUPPLEMENTS
ON
OFF
ON
ON
ON
ON
OFF
SUPPLEMENTS DECODER
ALLOW 2 DIGIT SUPPLEMENTS
ALLOW 5 DIGIT SUPPLEMENTS
REQUIRE SUPPLEMENTS
SEND SEPARATOR S PACE
INT. 2 OF 5
I 2 OF 5 DECODER
CHECK DIGIT
SEND CHECK DIGIT
FIXED LENGTH
SET F IXED LENGTH #1
SET F IXED LENGTH #2
ON
NONE
OFF
OFF
06
00
CODABAR DECODER
SEND START/STOP
CLSI FORMATTING
CLSI CHECK DIGIT
ON
OFF
OFF
OFF
CODE 93
ON
OFF
ON
CODE 93 DECODER
CONCATENATE MODE
MSI/PLESSEY
MSI/PLESSEY DECODER
TWO CHECK DIGITS REQUIRED
FIRST CHECK DIGIT MOD 11
SEND 1ST CHECK DIGIT
SEND 2ND CHECK DIGIT
ISBN PLESSEY
OFF
ON
ON
OFF
OFF
CODABAR
CODE 128
CODE 128 DECODER
UCC-128 VERIFICATION
SEND MOD 10 CHECK DIGIT
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
CODE 11
OFF
OFF
OFF
OFF
OFF
OFF
CODE 11 DECODER
TWO CHECK DIGITS REQUIRED
SEND 1ST CHECK DIGIT
SEND 2ND CHECK DIGIT
7
OFF
OFF
OFF
OFF
PREAMBLE
ENTER PREAMBLE
PREAMBLE SEND DELAY
ACTIVE TYPES
POSTAMBLE
NONE
0.0 SEC.
ALL
ENTER POSTAMBLE
POSTAMBLE SEND DELAY
ACTIVE
TERMINATION CHARACTER
TERMINATION CHARACTER
BAR CODE EDIT
CR
BAR CODE EDITING
ENTER # OF LEADING STRIP CHAR'S
ENTER # OF TRAILING STRIP C HAR'S
ENTER BAR CODE TYPE TO EDIT
STRIP LEADING & TRAILING S PACES
BEEP TONE
BEEP TONE
MEDIUM
BEEP LENGTH
MEDIUM SHORT
TRANSMIT SPEED
IBM AT
USA
ON
TRANSMIT SPEED
DIAGNOSTICS
DIAGNOSTIC SELF TEST
OFF
0
0
ALL
OFF
BEEP LENGTH
COMPUTER TYPE
COMPUTER TYPE
KEYBOARD T YPE
KEYBOARD INSTALLED
NONE
0.0 SEC.
ALL
FAST
OTHER OPTIONS
OFF
SEND BAR CODE TYPE ID
FUNCTION KEYS
KEYBOARD CAPS LOCK STATUS
KEYBOARD N UM LOCK S TATUS
SPECIAL KEYS
KEYBOARD A UTO C APS/N UM LOCK
ALTERNATE KEYBOARD SCAN CODES
TERMINATION CHARACTER OVERRIDE
READ REVERSE IMAGE BAR CODES
8
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
CHANGING THE DEFAULT SETTINGS
You can easily change the default settings by simply scanning the bar code options
located on the READER SETUP MENU. The READER SETUP MENU is a
laminated sheet of bar codes supplied with this manual.
The basic programming sequence is:
START / CATEGORY / OPTION (0-9) / ON/OFF (or) NUMBER ONLY /
EXIT
Follow the instructions below to change the settings.
Step 1:
Scan the START label at the top left corner of the SETUP MENU.
This puts the reader into the program mode.
Step 2:
Scan one of the CATEGORY labels (i.e. Code 39, UPC, Computer
Type, Transmit Speed).
Step 3:
Select the desired option by scanning one of the numeric labels
(0 - 9).
Step 4:
If there is an (ON/OFF) next to the description, scan an ON label to
enable or OFF label to disable the option.
EXAMPLE: To enable the MOD 43 check digit on Code
39, perform the following:
1) Scan the "CODE 39" category label.
2) Scan the option "2" label to select the "MOD 43
CHECK DIGIT" option.
3) Scan the "ON" label to enable option (2).
If there is a range of numbers next to the option, then scan one of
the numeric labels (0 - 9).
EXAMPLE: To select the OPCC check digit for
Interleaved 2 of 5, perform the following:
1)
2)
3)
Scan the "INT. 2 OF 5" category label.
Scan the "1" label to select the "CHECK DIGIT" option.
Scan the "2" label to select OPCC.
9
Step 5:
If you want to make another change within the SAME CATEGORY,
you can scan another option number (i.e., return to "Step 3"
above). If you want to make a change in a DIFFERENT
CATEGORY you MUST scan the new CATEGORY (i.e., return to
"Step 2" above and repeat the steps).
Step 6:
When you have finished making all of the changes, you can either:
1)
SCAN the EXIT (Save Changes) label to save all the changes
OR
2)
SCAN the EXIT (Ignore Changes) label to exit without saving
any changes.
NOTE: You can reset the reader to the default setting
by performing the following:
1)
2)
3)
Scan the START label.
Scan the RESET ALL DEFAULTS label.
Scan the EXIT (Save Changes) label.
10
PROGRAMMING GUIDE
START
The START bar code places the reader into the program mode. After scanning
this label, the reader will emit three short BEEPS to indicate that it is in the
program mode.
EXIT (SAVE CHANGES)
Scan this bar code to EXIT the program mode and save all of the changes. After
scanning this label, the reader will BEEP twice, then delay approximately one
second, and emit three short BEEPS to indicate that it accepted the changes.
EXIT (IGNORE CHANGES)
Scan this bar code to EXIT the program mode and DISCARD all of the current
changes. The reader will use the settings that were in effect before entering the
program mode.
RESET ALL DEFAULTS
Scan this bar code to RESET all options to their DEFAULT settings.
0-9 BAR CODES
These bar codes are scanned to select various options and enter programmable
data into the reader.
NOTE:
ON
OFF
Scan option (9) to reset all of the options within
the current CATEGORY back to their defaults.
If the OPTION has an (ON/OFF) beside the description, scan the ON bar code
to turn ON the current option.
If the OPTION has an (ON/OFF) beside the description, scan the OFF bar code
to turn OFF the current option.
FULL ASCII CHART
The FULL ASCII CHART is located on the back of the SETUP MENU. This chart
contains the entire ASCII character set (128 characters). Use this chart to enter
PREAMBLE and POSTAMBLE character strings, or for a USER DEFINED
TERMINATION CHARACTER.
ADDITIONAL NOTES:
If the description beside the OPTION contains:
(ON/OFF) Then scan either an ON or OFF label to set the option.
(CHART) Then scan one or more characters from the Full ASCII Chart.
(0-9)
Scan the desired character from the 0-9 labels.
(0.0-9.9) Scan two characters from the 0-9 labels to set the time from
0.0 to 9.9 seconds.
11
* NOTE: Defaults are marked with " * ".
CODE 39
0) CODE 39 DECODER
ON *
Enable reading CODE 39 labels.
OFF
1) FULL ASCII
ON
OFF *
Disable reading CODE 39 labels.
Enable the FULL ASCII EXTENSION to CODE 39.
Option (0) above must be ON. A Full ASCII Chart is
provided in Appendix C.
Disable the FULL ASCII EXTENSION to CODE 39.
This sets the reader to the standard CODE 39 mode.
2) MOD 43 CHECK DIGIT
ON
Enable the MOD 43 CHECK DIGIT for CODE 39.
When this option is enabled, only CODE 39 labels
that contain a valid check digit will be read.
OFF *
Disable the MODE 43 CHECK DIGIT.
verification will not be performed.
Check digit
3) SEND CHECK DIGIT
ON
Transmit the MOD 43 CHECK DIGIT with the bar
code data. Requires option (2) above to be ON.
OFF *
Do not transmit the MOD 43 CHECK DIGIT.
4) CONCATENATE MODE
ON
Enable CONCATENATE MODE. The concatenate
mode allows the reader to accumulate multiple bar
codes in its buffer, then send them to the computer
just like they were a single bar code. When a Code
39 label containing a leading space is read, the
reader emits two short beeps and buffers the data
without transmission. This process continues until a
Code 39 label without a leading space is read or 128
characters are buffered. A Code 39 bar code label
that only contains a single or multiple dashes (minus
sign) will clear the buffer.
OFF *
Disable CONCATENATE MODE.
12
UPC
0) UPC DECODER
ON *
Enable reading UPC-A and UPC-E labels.
OFF
Disable reading UPC-A and UPC-E labels.
1) CONVERT UPC-E TO UPC-A
ON
Convert all UPC-E labels to their UPC-A equivalents
before transmission. After conversion, the reader will
follow the UPC-A programming options.
OFF *
No UPC-E conversions will be performed.
2) CONVERT UPC-A TO EAN-13
ON
Convert all UPC-A labels to an equivalent EAN-13
format by inserting a leading zero. After conversion,
the reader will follow the EAN-13 programming
options.
OFF *
No UPC-A conversions will be performed.
3) SEND UPC-A NUMBER SYSTEM
ON *
Transmit the UPC-A NUMBER SYSTEM character.
OFF
Do not transmit the UPC-A NUMBER SYSTEM
character.
4) SEND UPC-E NUMBER SYSTEM
ON *
Transmit the UPC-E NUMBER SYSTEM character.
OFF
Do not transmit the UPC-E NUMBER SYSTEM
character.
5) SEND UPC-A CHECK DIGIT
ON *
Transmit the UPC-A CHECK DIGIT character.
OFF
Do not transmit the UPC-A CHECK DIGIT character.
6) SEND UPC-E CHECK DIGIT
ON *
Transmit the UPC-E CHECK DIGIT character.
OFF
Do not transmit the UPC-E CHECK DIGIT character.
13
EAN
0) EAN DECODER
ON *
Enable reading EAN-8 and EAN-13 labels.
OFF
Disable reading EAN-8 and EAN-13 labels.
1) ZERO FILL EAN-8 TO EAN-13
ON
Add five leading zeroes to EAN-8 labels. After
conversion, the reader will follow the EAN-13
programming options.
OFF *
No conversion is performed.
2) SEND EAN-13 COUNTRY CODE
ON *
Transmit the EAN-13 COUNTRY CODE.
OFF
Do not transmit the EAN-13 COUNTRY CODE.
3) SEND EAN-8 COUNTRY CODE
ON *
Transmit the EAN-8 COUNTRY CODE.
OFF
Do not transmit the EAN-8 COUNTRY CODE.
4) SEND EAN-13 CHECK DIGIT
ON *
Transmit the EAN-13 CHECK DIGIT character.
OFF
Do not transmit the EAN-13 CHECK DIGIT character.
5) SEND EAN-8 CHECK DIGIT
ON *
Transmit the EAN-8 CHECK DIGIT character.
OFF
Do not transmit the EAN-8 CHECK DIGIT character.
6) ISBN CONVERSION
ON
Convert 13 DIGIT BOOKLAND/EAN (978 prefix) to
it's corresponding 10 DIGIT ISBN number.
EXAMPLE: BAR CODE DATA = 9780806957906
ISBN OUTPUT
=
0806957905
OFF *
Do not convert BOOKLAND/EAN to ISBN number.
14
UPC/EAN SUPPLEMENTS
0) SUPPLEMENTS DECODER
ON
Enable reading UPC & EAN supplements.
OFF*
Disable reading UPC & EAN supplements.
1) ALLOW 2 DIGIT
ON*
Enable reading 2 digit supplements.
above must be set ON.
OFF
Disable reading 2 digit supplements.
2) ALLOW 5 DIGIT
ON*
Enable reading 5 digit supplements.
above must be set ON.
OFF
Option (0)
Option (0)
Disable reading 5 digit supplements.
3) REQUIRE SUPPLEMENTS
Specifies how the reader will handle various supplements.
0)*
UPC/EAN bar codes will be read with or without valid
supplements.
1)
UPC bar codes will not be read unless they are
accompanied by a valid supplement.
2)
EAN bar codes will not be read unless they are
accompanied by a valid supplement.
3)
Bookland EAN bar codes will not be read unless they
are accompanied by a valid supplement.
4)
All UPC/EAN bar codes will not be read unless they
are accompanied by a valid supplement.
4) SEND SEPARATOR SPACE
ON
Insert a space between the standard bar code data
and the supplemental data.
OFF*
No separator space is inserted.
15
INTERLEAVED 2 OF 5
0) I 2 OF 5 DECODER
ON *
Enable reading INTERLEAVED 2 OF 5 labels.
OFF
Disable reading INTERLEAVED 2 OF 5 labels.
1) CHECK DIGIT: 0=NONE, 1=USS, 2=OPCC
Specifies which type of check digit will be used with
INTERLEAVED 2 of 5.
0*
1
2
NONE (no check digit required)
UNIFORM SYMBOLOGY SPECIFICATION
(3-1-3 MOD 10)
OPTICAL PRODUCT CODE COUNCIL
(2-1-2 MOD 10)
2) SEND CHECK DIGIT
ON
Transmit the INTERLEAVED 2 OF 5 check digit with
the bar code data.
OFF *
The check digit is not transmitted.
3) FIXED LENGTH
ON
Read only FIXED LENGTH INTERLEAVED 2 OF 5
bar code labels that match the lengths defined in
options (4) & (5) below. (The SEND CHECK DIGIT
option can be ON or OFF.)
OFF *
Disable FIXED LENGTH mode.
Read all
INTERLEAVED 2 OF 5 labels without regard to
length.
4) SET FIXED LENGTH #1 (02-60)
Sets the first valid FIXED LENGTH for Interleaved 2 of 5.
Scan a two digit value to enter the length. Valid lengths are 02
- 60 characters. By definition, the length of INTERLEAVED 2
OF 5 labels are an even number of characters. The default
FIXED LENGTH is six (06) characters.
5) SET FIXED LENGTH #2 (02-60)
Sets a second valid fixed LENGTH for INTERLEAVED
2 OF 5. Scan a two digit value to enter the length. The default
length is set to zero (00) characters (i.e. the second FIXED
LENGTH is disabled).
16
CODABAR
0) CODABAR DECODER
ON *
Enable reading CODABAR labels.
OFF
Disable reading CODABAR labels.
1) SEND START/STOP
ON
Transmit the CODABAR start/stop characters.
OFF *
Do not transmit the CODABAR start/stop characters.
2) CLSI FORMATTING
ON
The reader will insert a blank after the 1st, 5th, and
10th characters of a 14-character CODABAR label.
The label length does not include the start and stop
characters.
OFF *
Disable CLSI formatting.
3) CLSI CHECK DIGIT
ON
Enable the CLSI check digit. When this option is
enabled, all fourteen digit numeric bar codes must
contain a valid check digit.
OFF*
Disable the CLSI check digit. Check digit verification
will not be performed.
CODE 128
0) CODE 128 DECODER
ON *
Enable reading Code 128 labels.
OFF
Disable reading Code 128 labels.
1) UCC-128 VERIFICATION
ON
A valid MOD 10 CHECK DIGIT is required on UCCMOD 10 bar codes. (Applies to 20-digit serial
shipping container bar codes.)
OFF *
UCC-MOD 10 bar codes are accepted without valid
MOD 10 CHECK DIGITS.
2) SEND MOD 10 CHECK DIGIT
ON *
Transmit the MOD 10 CHECK DIGIT with the bar
code entry.
OFF
Do not transmit the MOD 10 CHECK DIGIT.
17
CODE 93
0) CODE 93 DECODER
ON *
Enable reading CODE 93 labels.
OFF
Disable reading CODE 93 labels.
1) CONCATENATE MODE
ON
Enable CONCATENATE MODE. The concatenate
mode allows the reader to concatenate multiple bar
codes in its buffer, then send them to the computer
just like they were a single bar code. When a Code
93 label with a leading space is read, the reader
emits two short beeps and buffers the data without
transmission. This process continues until a Code 93
label without a leading space is read or 128
characters are buffered. A Code 93 bar code label
that only contains a single or multiple dashes (minus
sign) will clear the buffer.
OFF *
Disable CONCATENATE MODE.
18
MSI/PLESSEY
0) MSI/PLESSEY DECODER
ON
Enable reading MSI/PLESSEY labels.
OFF *
Disable reading MSI/PLESSEY labels.
1) TWO CHECK DIGITS REQUIRED
ON
Two valid CHECK DIGITS are required for each label.
The first check digit is defined by option (2) below.
The second check digit is always MOD 10.
OFF *
One valid CHECK DIGIT is required for each label.
The CHECK DIGIT must be MOD 10.
2) FIRST CHECK DIGIT MOD 11
ON
The FIRST CHECK DIGIT must be MOD 11.
OFF *
The FIRST CHECK DIGIT must be MOD 10.
3) SEND FIRST CHECK DIGIT
ON
Transmit the FIRST CHECK DIGIT.
OFF *
Do not transmit the FIRST CHECK DIGIT.
4) SEND SECOND CHECK DIGIT
ON
Transmit the SECOND CHECK DIGIT.
OFF *
Do not transmit the SECOND CHECK DIGIT.
5) ISBN PLESSEY
ON
Enable reading of Modified Plessey ISBN bar codes.
Only eleven digit ISBN bar codes will be read.
OFF*
Do not read Modified Plessey ISBN bar codes.
19
CODE 11
0) CODE 11 DECODER
ON
Enable reading CODE 11 labels.
OFF *
Disable reading CODE 11 labels.
1) TWO CHECK DIGITS REQUIRED
ON
Two valid CHECK DIGITS are required for each label.
OFF *
One valid CHECK DIGIT is required for each label.
2) SEND FIRST CHECK DIGIT
ON
Transmit the FIRST CHECK DIGIT.
OFF *
Do not transmit the FIRST CHECK DIGIT.
3) SEND SECOND CHECK DIGIT
ON
Transmit the SECOND CHECK DIGIT.
OFF *
Do not transmit the SECOND CHECK DIGIT.
20
PREAMBLE
0) ENTER PREAMBLE
This set of user-defined characters is transmitted at the
beginning of bar code data. To define the PREAMBLE, scan
up to 15 characters from the FULL ASCII chart on the reverse
side of the SETUP MENU. Scan the "ON" bar code when
complete.
1) PREAMBLE SEND DELAY (0.0 - 9.9 SEC)
This option specifies the amount of delay to occur after the
PREAMBLE is transmitted. The delay period is programmable
from 0.0 to 9.9 seconds. The default setting is 0.0 seconds.
2) ACTIVE TYPES
Specifies the types of bar codes that use preambles. Select
one of the following:
A
B
C
D
CODE 39
UPC-A
UPC-E
EAN-13
E EAN-8
I
F I 2 of 5
J
G CODABAR
K
H CODE 128
L
X* ALL BAR CODES
CODE 93
MSI/PLESSEY
CODE 11
ISBN
POSTAMBLE
0) ENTER POSTAMBLE
This set of user-defined characters is transmitted at the end of
bar code data. To define the POSTAMBLE, scan up to 15
characters from the FULL ASCII chart on the reverse side of
the SETUP MENU. Scan the "ON" bar code when complete.
1) POSTAMBLE SEND DELAY (0.0 - 9.9 SEC)
This option specifies the amount of delay to occur after the
POSTAMBLE is transmitted.
The delay period is
programmable from 0.0 to 9.9 seconds. The default setting is
0.0 seconds.
3
4
CARRIAGE RETURN & LINE FEED
(ASCII 13 & ASCII 10)
USER DEFINED TERMINATION CHARACTER
2) ACTIVE TYPES
Specifies the types of bar codes that use postambles. Select
one of the following:
A
B
C
D
CODE 39
UPC-A
UPC-E
EAN-13
E EAN-8
I
F I 2 of 5
J
G CODABAR
K
H CODE 128
L
X* ALL BAR CODES
21
CODE 93
MSI/PLESSEY
CODE 11
ISBN
BAR CODE EDIT
This option allows editing bar codes before transmittal.
0) BAR CODE EDITING
(Must be ON for any of the editing options below to be valid.)
ON
Enable Bar Code Editing.
OFF *
Disable Bar Code Editing.
1) ENTER # OF LEADING CHARS TO STRIP (0-9, A-F)
(Option (0) above must be ON.) Refers to the number (0-15)
of bar code characters to be stripped, i.e., removed, from the
beginning of the data entry.
2) ENTER # OF TRAILING CHARS TO STRIP (0-9, A-F)
(Option (0) above must be ON.) Refers to the number (0-15)
of bar code characters to be stripped, i.e., removed, from the
end of the data entry.
NOTE:
If the total number of strip characters (both
Leading and Trailing) is greater than the
number of characters of the bar code, no
characters will be stripped.
3) ENTER BAR CODE TYPE TO EDIT
(Option (0) above must be ON.) Refers to the type of bar
codes for which editing can be enabled. The choices are
listed below:
A
B
C
D
E
F
CODE 39
UPC-A
UPC-E
EAN-13
EAN-8
INTERLEAVED 2 of 5
G
H
I
J
K
X*
CODABAR
CODE 128
CODE 93
MSI/PLESSEY
CODE 11
ALL BAR CODES
4) STRIP LEADING & TRAILING SPACES
(Option (0) above must be ON.)
ON
Any LEADING & TRAILING SPACES will be stripped
from the data.
OFF *
No spaces will be stripped.
22
TERMINATION CHARACTER
The optional TERMINATION CHARACTER is transmitted at the end of
the data. This option applies to bar code, mag stripe, and serial data.
If a USER DEFINED TERMINATION CHARACTER is desired, select
setting (4) below, then scan a single character from the FULL ASCII
section of the MENU.
0
1
2*
3
4
NONE
HORIZONTAL TAB (ASCII 09)
CARRIAGE RETURN (ASCII 13)
CARRIAGE RETURN & LINE FEED
(ASCII 13 & ASCII 10)
USER DEFINED TERMINATION CHARACTER
BEEP TONE
This option sets the frequency (pitch) of the beep tone. Select one of
the following:
0
1
2*
3
NONE
LOW
MEDIUM
HIGH
BEEP LENGTH
This option sets the length of the beep tone.
following:
0
1*
2
3
SHORT
MEDIUM SHORT
MEDIUM LONG
LONG
23
Select one of the
COMPUTER TYPE
This option defines both the type of computer and the type of keyboard
that will be used. The selections must be made properly for the data to
transmit correctly. Note the UNIVERSAL keyboard setting below, which
can be used for all international keyboards.
Select a COMPUTER TYPE from settings (0-3), and a KEYBOARD
TYPE from setting (4):
0
1*
2
3
4
NOTE:
5)
IBM PC/XT (8088 and 8086 processors)
IBM AT (286, 386, and 486 processors)
IBM PS/2 MODELS 25, 30, 57, & 90
(and some MODEL 70's)
IBM PS/2 MODELS 30-286, 50, 55, 60, 70, 80
KEYBOARD TYPE. Select from the following:
0) *
USA
1)
FRENCH
2)
GERMAN
3)
ITALIAN
9)
UNIVERSAL
For all XT computers, select UNIVERSAL as
the KEYBOARD TYPE to ensure proper
upper/lower case transmission.
KEYBOARD INSTALLED
ON*
The computer has a keyboard
installed .
OFF
The computer does not have a
keyboard installed.
NOTE: Option (5) is not applicable to PC/XT computers.
TRANSMIT SPEED
This option sets the speed at which data will be transmitted to the
computer. Some computer systems may require the transmission
speed to be set to a slower speed. The default setting is (3), FAST.
0
1
2
3*
SLOW
MEDIUM SLOW
MEDIUM FAST
FAST
24
OTHER OPTIONS
0) SEND BAR CODE TYPE ID
ON
Transmit the bar code identifier character at the
beginning of the bar code data. There is one space
between the ID character and the bar code data. The
identifier characters are defined below:
A
B
C
D
E
F
OFF *
CODE 39
UPC-A
UPC-E
EAN-13
EAN-8
INTERLEAVED 2 of 5
G
H
I
J
K
CODABAR
CODE 128
CODE 93
MSI/PLESSEY
CODE 11
Do not transmit BAR CODE TYPE ID.
1) FUNCTION KEYS
ON
Applies to bar code data, preambles, postambles,
and user defined termination characters. FUNCTION
KEYS F1 through F10 will be transmitted in place of
the ASCII characters "DC1" (11H) through "SUB"
(1AH). The FUNCTION KEY values are listed in the
Full ASCII Chart on back of the MENU, and in
Appendix A.
OFF *
NOTE:
Disable FUNCTION KEYS.
(Standard ASCII characters are transmitted.)
See option (4) for a related example.
2) KEYBOARD CAPS LOCK STATUS
Setting this function is necessary only if option (5),
KEYBOARD AUTO CAPS/NUM LOCK, does not operate on
your computer. See option (5) to determine whether
KEYBOARD CAPS LOCK STATUS is required.
To use this option, scan either ON or OFF to match the
computer keyboard's CAPS LOCK status.
ON *
Scan ON to indicate that the keyboard's CAPS
LOCK is turned ON. The result is lower case
Alpha characters being output as Shifted
characters.
OFF
Scan OFF to indicate that the keyboard's CAPS
LOCK is turned OFF. The result is upper case
Alpha characters being output as Shifted
characters.
25
3) KEYBOARD NUM LOCK STATUS
Setting this function is necessary only if option (5),
KEYBOARD AUTO CAPS/NUM LOCK, does not operate on
your computer. See (5) to determine whether KEYBOARD
NUM LOCK STATUS is required.
To use this option, scan either ON or OFF to match the
computer keyboard's NUM LOCK status.
ON
Scan ON to indicate that the computer keyboard's
NUM LOCK is turned ON.
OFF *
Scan OFF to indicate that the computer keyboard's
NUM LOCK is turned OFF.
4) SPECIAL KEYS
This option applies to bar code data, preambles, postambles,
and user defined termination characters.
ON
SPECIAL KEY characters will be transmitted in place
of a specific set of ASCII characters. The SPECIAL
KEYS are listed in the Full ASCII Chart provided on
back of the SETUP MENU and in Appendix A.
OFF *
Disable SPECIAL KEYS.
(Standard ASCII characters are transmitted.)
EXAMPLE: With SPECIAL KEYS ON, the bar code
character "STX" will be transmitted as a right
arrow, having the effect of pressing the "→"
key at the keyboard.
NOTE:
If the Bar Code Reader is not transmitting
the special characters with SPECIAL KEYS
ON, or if the computer is an XT, see
option (5), "Keyboard Auto Caps/Num Lock".
5) KEYBOARD AUTO CAPS/NUM LOCK
With this option ON, data is automatically transmitted in the
correct upper/lower case, whether the keyboard's settings are
turned ON or OFF.
ON *
Enable KEYBOARD AUTO CAPS/NUM LOCK.
OFF
Disable KEYBOARD AUTO CAPS/NUM LOCK.
26
NOTE
The KEYBOARD AUTO CAPS/NUM LOCK option is
NOT effective on some computers, such as XT's.
Indications that this option is NOT functioning are as
follows:
Upper/Lower Case are reversed.
SPECIAL KEY characters are not transmitted
when SPECIAL KEYS are ON.
If KEYBOARD AUTO CAPS/NUM LOCK is NOT operating properly on your system, take the following steps:
Set KEYBOARD AUTO CAPS/NUM LOCK to
OFF.
Set KEYBOARD CAPS LOCK STATUS. (See
option (2).)
Set KEYBOARD NUM LOCK STATUS. (See
option (3).)
6) ALTERNATE KEYBOARD SCAN CODES
This option is necessary ONLY for computers that use SCAN
CODE Set 3. Note that it might be necessary to disable option
(5), KEYBOARD AUTO CAPS/NUM LOCK.
ON
Enable ALTERNATE KEYBOARD SCAN CODES.
OFF *
Disable ALTERNATE KEYBOARD SCAN CODES.
7) TERM CHAR OVERRIDE
ON
If any control character or special character (ie.,
function key, arrow key, etc...) is embedded in the bar
code data, the TERMINATION CHARACTER, the
PREAMBLE, and the POSTAMBLE will not be
transmitted.
OFF * The TERMINATION CHARACTER, the PREAMBLE,
and the POSTAMBLE will be transmitted with all bar
code data.
8) READ REVERSE IMAGE BAR CODES
ON
Enable reading of Reverse Image (negative image)
bar codes.
OFF * Disable the reading of Reverse Image (negative
image) bar codes.
27
DIAGNOSTICS
This option executes a self-test program which performs the following
tests on the reader:
*
EPROM Version Number
*
Internal and External Ram Test
*
EPROM Checksum Test
*
Character Set Test
*
Buzzer Test
The above tests are performed and their status is displayed on the PC
monitor.
NOTE: Exit your application program and return to DOS before
enabling this test.
28
SPECIFICATIONS
BAR CODES SUPPORTED
Auto-discriminates between all of the following codes:
- Code 39
- Extended Code 39 (Full ASCII)
- Interleaved 2 of 5 (Variable and Fixed Length, Check Digit)
- UPC-A (Including 2 and 5 Character Supplements)
- UPC-E(0), UPC-E(1) (Including 2 and 5 Character Supplements)
- EAN (Including 2 and 5 Character Supplements)
- Code 128 (UCC-128 Verification, Check Digit)
- Codabar
- Code 93
- Code 11
- MSI/Plessey
INPUT DEVICES SUPPORTED
Wands (Visible and Infrared)
Slot Readers (Or Badge Readers)
USER PROGRAMMABLE FEATURES
All features are easily programmed with a bar code menu:
Bar Code Selection:
Preamble (15 Chars Max)
- Enable/Disable
Postamble (15 Chars Max)
- Length
Computer Type
- Check Digit
Keyboard Type (US & Foreign)
- Start/Stop Transmit
Transmit Speed
Beep Tone and Length
User Defined Termination Char.
INDICATORS
Audio "BEEP" indicates Successful Read
A Red/Green LED Indicates Status of Reader
POWER REQUIREMENTS
Reader Receives its Power from the Personal Computer Keyboard Interface.
CONNECTORS
Wand: 5 Pin DIN Style
Keyboard Interface: M1000 = 5 Pin DIN Style
M1002 = 6 Pin MINI-DIN Style
ENVIRONMENTAL
Operating Temperature:
Storage Temperature:
Relative Humidity:
PHYSICAL SPECIFICATIONS
Weight: 14 Ounces
Length: 5 1/4 Inches
0o to +50o C
-30o to +70o C
5% to 95% (Non-Condensing)
Width: 5 1/8 Inches
Height: 1 1/2 Inches
29
SIGNAL DEFINITIONS
WAND INTERFACE
PIN
1
2
3
4
5
SIGNAL
+5V
DATA
GROUND
NO CONNECTION
NO CONNECTION
5
1
4
2
3
M1000 KEYBOARD/COMPUTER INTERFACE
PIN
1
2
3
4
5
SIGNAL
KEYBOARD CLOCK
GROUND
KEYBOARD DATA
+5V
SPARE
1
5
4
2
3
M1002 KEYBOARD/COMPUTER INTERFACE
PIN
1
2
3
4
5
6
SIGNAL
KEYBOARD DATA
RESERVED
GROUND
+5V
KEYBOARD CLOCK
RESERVED
6
4
30
2
1
5
3
APPENDIX A - FUNCTION & SPECIAL KEYS
With FUNCTION KEYS enabled, the decoder can accept a given ASCII
character and transmit a corresponding FUNCTION KEY to the computer. The
ASCII characters and values are listed in the table below.
ASCII CHARACTERS
FUNCTION KEYS
ASCII VALUES
DC1
F1
17
DC2
F2
18
DC3
F3
19
F4
20
DC4
NAK
F5
21
SYN
F6
22
26
ETB
F7
23
CAN
F8
24
EM
F9
25
SUB
F10
26
SPECIAL KEYS
With SPECIAL KEYS enabled, the decoder can accept a given ASCII character
and transmit a corresponding SPECIAL KEY to the computer. The ASCII
characters and values are listed in the table below.
ASCII CHARACTERS
SPECIAL KEYS
ASCII VALUES
SOH
(Left Arrow)
1
STX
(Right Arrow)
2
ETX
(Up Arrow)
3
EOT
(Down Arrow)
4
ENQ
HOME
5
ACK
END
6
BEL
DELETE
7
VT
PAGE UP
11
FF
PAGE DOWN
12
SO
SHIFT ON
14
SI
SHIFT OFF
15
DLE
INS
16
FS
CTRL ON
28
GS
CTRL OFF
29
RS
ALT ON
30
US
ALT OFF
31
A-1
APPENDIX B - CODE 39 SPECIFICATIONS
Code 39 is a variable length alphanumeric code. Each character is made up of
nine elements, five bars and four spaces. Three of the elements are wide and
six are narrow. Code 39 is a popular choice for applications because:
-
it is easy to print with low cost dot matrix printers
large character set (A-Z, 0-9, 7 special characters)
code can be extended to include the entire 128 ASCII character set
variable length.
0123456789
ABCDE12345
CHARACTERISTICS:
Character Set: 26 uppercase letters (A - Z)
10 digits (0 - 9)
7 special characters (SPACE -.$/+%)
Symbol Length: Variable
Check Digit: Optional
Bi-directional Decoding: Yes
Maximum Density: 9.8 char./inch
(using .0075 inch narrow element)
B-1
CODE 39 CHARACTER SET:
An optional check character can be used for applications requiring higher levels
of data security. When used, the check character immediately follows the last
data character. The check digit is calculated as follows:
1.
Each data character is assigned a numerical value as shown in the
following table:
CHAR
VALUE
CHAR
VALUE
CHAR
VALUE
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
U
V
W
X
Y
Z
.
SPACE
$
/
+
%
30
31
32
33
34
35
36
37
38
39
40
41
42
B-2
2.
Sum all of the numerical values for each data character in the bar code.
3.
Divide this sum by 43.
4.
The remainder is the numerical value for the check digit. Use the table in
step 1 to look-up the corresponding character.
EXAMPLE: Sample Code 39 data = A394T
1.
2.
3.
4.
Use the table to lookup the numerical value for each character.
10 + 3 + 9 + 4 + 29 = 55
55 / 43 = 1 remainder 12
Check digit numerical value = 12
The check digit = C.
Bar code with check digit = A394TC
B-3
APPENDIX C - FULL ASCII EXTENSION TO CODE 39
The FULL ASCII EXTENSION expands standard CODE 39 to include the entire
128 ASCII character set. This is accomplished by pairing standard CODE 39
characters. The $, +, /, and % characters are paired as shown in the following
table:
ASCII
CODE
ASCII
CODE
ASCII
CODE
ASCII
CODE
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
SP
%U
$A
$B
$C
$D
$E
$F
$G
$H
$I
$J
$K
$L
$M
$N
$O
$P
$Q
$R
$S
$T
$U
$V
$W
$X
$Y
$Z
%A
%B
%C
%D
%E
SPACE
!
"
#
$
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
/A
/B
/C
/D
/E
/F
/G
/H
/I
/J
/K
/L
.
/O
0 or /P
1 or /Q
2 or /R
3 or /S
4 or /T
5 or /U
6 or /V
7 or /W
8 or /X
9 or /Y
/Z
%F
%G
%H
%I
%J
%V
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
`
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
%K
%L
%M
%N
%O
%W
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
¦
}
~
DEL
+A
+B
+C
+D
+E
+F
+G
+H
+I
+J
+K
+L
+M
+N
+O
+P
+Q
+R
+S
+T
+U
+V
+W
+X
+Y
+Z
%P
%Q
%R
%S
%T,%X,
%Y or
%Z
C-1
APPENDIX D - UPC SPECIFICATIONS
The Universal Product Code (UPC) symbols can be found on almost all retail
products today. The UPC coding system was designed to uniquely identify a
product and its manufacturer.
UPC VERSION A
UPC-A is a fixed length (12 digits) numeric only code with the following features:
0
5
12345 67890
Number System
Character
5-Digit
Product Code
5-Digit
Manufacturer
Number
Check Digit
UPC-A BAR CODE
The NUMBER SYSTEM CHARACTER indicates the type of product the symbol is
identifying:
0,7
2
3
4
5
Regular UPC codes with numbers assigned by the Uniform Code
Council (see Appendix J - Sources of Bar Code Standards).
Random-weight items such as meat and produce.
National Drug Code and National Health-Related Items Code.
For in-store marking of non-food items.
Reserved for coupons.
1,6,8,9 Reserved for future use.
D-1
The last digit in UPC bar codes is a MODULO 10 CHECK DIGIT. It is calculated in
the following manner:
1.
From right to left, sum the digits in the odd positions.
2.
Multiply this sum by 3.
3.
From right to left, sum the digits in the even positions.
4.
Add this sum to the product of Step 2.
5.
The modulo-10 check digit is the smallest number, which when
added to the sum of Step 4 produces a multiple of 10.
EXAMPLE:
1.
2.
3.
4.
5.
UPC bar code = 01234567890C where C is the
CHECK DIGIT.
Sum 0 + 8 + 6 + 4 + 2 + 0 = 20
Multiply 20 x 3 = 60
Sum 9 + 7 + 5 + 3 + 1 = 25
Sum 60 + 25 = 85
85 + 5 = 90 (check digit = 5)
Therefore: UPC bar code - 012345678905
UPC VERSION E
UPC Version E is a six digit variation of the UPC symbology. The last digit indicates
the type of compression used. Because of this data compression process, the
Version E symbol is often referred to as a zero-suppressed symbol.
173559 8
D-2
The following table illustrates the expansion process for converting UPC-E to its
UPC-A equivalent:
Version E
Number
Insertion
Digits
Insertion
Location
Resultant
Version A
XXXXX0
XXXXX1
XXXXX2
XXXXX3
XXXXX4
XXXXX5
XXXXX6
XXXXX7
XXXXX8
XXXXX9
00000
10000
20000
00000
00000
0000
0000
0000
0000
0000
Position 3
Position 3
Position 3
Position 4
Position 5
Position 6
Position 6
Position 6
Position 6
Position 6
XX00000XXX
XX10000XXX
XX20000XXX
XXX00000XX
XXXX00000X
XXXXX00005
XXXXX00006
XXXXX00007
XXXXX00008
XXXXX00009
173559 8
0
VERSION E
17355 00009
8
VERSION A EQUIVALENT
UPC/EAN SUPPLEMENTS
UPC and EAN bar codes can contain supplements that provide two or five digits of
additional information. The supplements are located to the right of standard UPC/
EAN labels. The reader can be programmed to either read or ignore the supplements.
10
0
12345
0
12345 67890
01234 56789
D- 3
APPENDIX E - EAN SPECIFICATIONS
The European Article Numbering system (EAN) is a superset of UPC. EAN has two
versions: EAN-13 (13 digits) and EAN-8 (8 digits).
5 012345 678900
5012 3452
EAN 13
EAN 8
Country codes 00, 01, 03, 04, and 06 - 09 are assigned to the U.S. for compatibility
with UPC.
E-1
APPENDIX F - INTERLEAVED 2 OF 5 SPECIFICATIONS
The Interleaved 2 of 5 bar code symbology is a numeric code (0 - 9) which has
different start and stop characters. The name Interleaved 2 of 5 is derived from the
fact that two characters are paired together using the bars to represent the first
character and spaces to represent the second. Each character has two wide
elements and three narrow elements.
CHARACTERISTICS:
Character Set:
Symbol Length:
Check Digit:
Bi-directional Decoding:
Maximum Density:
Numeric only (0 - 9)
Variable (must be an even number of digits)
Optional
Yes
18 char./inch
(using .0075 inch narrow element)
CHARACTER SET:
The following table illustrates the data patterns. A "1" represents a wide bar or space
and a "0" represents a narrow bar or space.
CHARACTER
PATTERN
0
1
2
3
4
5
6
7
8
9
start
stop
00110
10001
01001
11000
00101
10100
01100
00011
10010
01010
0000
100
0123456789
F-1
OPTIONAL CHECK DIGIT:
Interleaved 2 of 5 may contain an optional check digit. The reader supports two
types of check digits:
1.
2.
Uniform Symbology Specification (USS) - calculated as modulo 10 check
digit based on 3-1-3 weightings.
Optical Product Code Council (OPCC) - calculated as modulo 10 check digit
based on 2-1-2 weightings.
USS CHECK DIGIT CALCULATION:
1.
2.
3.
4.
5.
From right to left, sum the digits in the odd positions.
Multiply this sum by 3.
From right to left, sum the digits in the even positions.
Add this sum to the product of Step 2.
The modulo-10 check digit is the smallest number which when
added to the sum of Step 4 produces a multiple of 10.
EXAMPLE: USS check digit. Sample bar code data: 513827
1. Sum 7 + 8 + 1 = 16
2. Multiply 16 x 3 = 48
3. Sum 2 + 3 + 5 = 10
4. Sum 48 + 10 = 58
5. 58 + 2 = 60 (check digit = 2)
Therefore: Data + check digit = 5138272
NOTE: A leading zero will be required to make it an even
number of characters. The resulting bar code will be:
05138272
OPCC CHECK DIGIT CALCULATION:
1.
2.
3.
4.
From right to left, assign every digit a weighting factor from the
sequence: 2,1,2,1,2,1,2,1...
Multiply each digit by its weighting factor.
Sum the products in step 2, treating two digit products as the sum
of the individual digits.
The check digit is the smallest number which when added to the
sum of step 3 produces a multiple of 10.
EXAMPLE:
1.
2.
3.
4.
OPCC check digit
Sample bar code data: 020489713
Assign weighting factors: 020489713 212121212
Calculate the products: 0 2 0 4 16 9 14 1 6
Sum the products: 0+2+0+4+1+6+9+1+4+1+6 = 34
34 + 6 = 40 (check digit = 6)
Therefore: Data + check digit = 0204897136
F-2
APPENDIX G - CODABAR SPECIFICATIONS
The Codabar bar code symbology is a numeric code (0 - 9) that also contains six
special characters and four start/stop characters. The start/stop characters may or
may not be transmitted. Characters are constructed of four bars and three spaces.
Codabar is commonly used in libraries, blood banks, cotton and transportation
industry.
CHARACTERISTICS:
Character Set:
Symbol Length:
Check Digit:
Bi-directional Decoding:
Maximum Density:
10 digits (0 - 9)
6 special characters (- $ : / . +)
4 stop/start characters (a b c d)
Variable
Optional
Yes
12.8 char./inch
(using .0075 inch narrow element)
CHARACTER SET:
The following table illustrates the data patterns. A "1" represents a wide bar or
space and a "0" represents a narrow bar or space.
CHARACTER
PATTERN
0
1
2
3
4
5
6
7
8
9
$
:
/
.
+
a
b
c
d
0000011
0000110
0001001
1100000
0010010
1000010
0100001
0100100
0110000
1001000
0001100
0011000
1000101
1010001
1010100
0010101
0011010
0101001
0001011
0001110
A123456B
G-1
APPENDIX H - CODE 128 SPECIFICATIONS
The CODE 128 symbology is a variable length alphanumeric code containing the full
128 ASCII character set. Each character consists of 11 modules containing three
bars and three spaces. Bars and spaces can be from 1 to 4 modules wide. Three
different start characters are used to select one of three character sets. Code 128
is the bar code of choice for new applications.
CHARACTERISTICS:
Character Set:
Symbol Length:
Check Character:
Bi-directional Decoding:
Maximum Density:
All 128 ASCII characters
4 function characters
4 code set selection characters
3 start/stop characters
Variable
1
Yes
12.1 alphanumeric char./inch
24.2 numeric digits/inch
(using .0075 inch module element)
0123456789
ABCD123
UCC-128 MOD 10 SERIAL SHIPPING CONTAINER CODE:
FORMAT:
STARTC
FNC1
0000012345555555555
(1)
(2)
(3)
1. Start Code "C"
2. FNC1 Character
3. 19 Digits
8
C
(4) (5)
STOP
(6)
4. MOD 10 Check Digit
5. MOD 103 Check Digit
6. Stop Code
00000123455555555558
H-1
CHARACTER SET:
The following table contains the character set for Code 128 subsets A, B, and C:
CODE 128 (USD-6)
VALUE
CODE
A
CODE
B
CODE
C
B
S
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
SP
!
"
#
$
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
SP
!
"
#
$
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
2
2
2
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
3
3
2
2
2
1
1
1
1
1
1
2
2
2
1
1
1
1
1
2
2
2
2
3
2
2
3
2
2
3
1
2
2
1
2
2
2
2
2
1
2
1
1
2
2
1
2
2
1
1
3
1
3
3
1
3
3
1
3
3
1
1
3
1
H-2
BAR PATTERN
B
S
B
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
3
3
3
3
1
1
3
3
2
1
1
1
2
2
2
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
3
2
1
2
2
3
2
2
3
2
2
3
2
2
1
2
2
1
2
2
1
2
2
1
1
2
1
2
2
1
2
1
3
1
3
1
3
3
1
3
3
1
3
1
3
1
1
2
2
2
2
2
2
1
1
1
1
1
1
3
3
3
2
2
2
1
3
3
1
1
3
2
2
2
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
3
3
3
2
S
2
2
1
3
2
2
3
2
2
3
2
2
2
2
1
2
2
1
1
2
1
2
2
1
2
2
1
2
2
1
3
1
1
3
3
1
3
3
1
3
3
1
3
1
1
3
CODE 128 (USD-6)
VALUE
CODE
A
CODE
B
CODE
C
B
S
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
1
1
3
2
2
2
2
2
3
3
3
3
3
3
3
2
4
1
1
1
1
1
1
1
1
1
1
1
1
2
2
4
2
1
1
1
1
1
1
1
4
4
4
2
2
1
3
1
1
3
1
1
1
1
1
3
1
1
3
1
2
3
1
1
2
2
4
4
1
1
2
2
4
4
4
2
1
4
3
1
2
2
1
2
2
1
2
2
1
1
H-3
BAR PATTERN
B
S
B
3
3
3
1
1
3
3
3
1
1
1
2
2
2
4
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
3
1
4
1
1
1
4
4
4
1
1
1
2
4
3
1
1
3
1
1
3
1
1
3
1
1
3
1
1
4
1
2
4
1
4
1
2
2
4
1
4
1
2
2
1
1
1
1
2
1
2
2
1
2
2
1
2
1
1
2
2
2
3
3
1
1
3
2
2
2
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
4
4
4
1
1
1
1
1
1
4
2
S
1
1
1
1
1
3
1
1
3
1
1
3
1
1
1
1
1
4
2
4
1
2
1
4
2
4
1
2
1
1
4
1
2
1
2
2
1
2
2
1
2
2
1
1
1
CODE 128 (USD-6)
VALUE
CODE
A
CODE
B
CODE
C
B
S
91
92
93
94
95
96
97
98
99
100
101
102
ESC
FS
GS
RS
US
FNC 3
FNC 2
SHIFT
CODE C
CODE B
FNC 4
FNC 1
{
¦
}
~
DEL
FNC 3
FNC 2
SHIFT
CODE C
FNC 4
CODE A
FNC 1
91
92
93
94
95
96
97
98
99
CODE B
CODE A
FNC 1
4
1
1
1
1
1
4
4
1
1
3
4
1
1
1
3
1
1
1
1
1
1
1
1
2
1
1
1
4
4
1
1
3
4
1
1
1
1
3
1
1
3
1
3
1
1
1
1
2
4
4
4
1
1
1
1
4
3
4
3
1
3
1
1
3
1
3
1
1
1
1
1
B
S
B
S
B
S
2
2
2
1
1
1
1
1
1
4
2
2
1
1
3
2
4
2
B
S
B
S
B
S
B
2
3
3
1
1
1
2
103
104
105
START (CODE A)
START (CODE B)
START (CODE C)
STOP
H-4
BAR PATTERN
B
S
B
S
APPENDIX I - CODE 93 SPECIFICATIONS
The Code 93 bar code symbology is a variable length alphanumeric code containing
the full 128 ASCII character set. Each character consists of 9 modules with three
bars and three spaces. The bars can be 1, 2, or 3 modules wide except for the start/
stop character. The spaces can be 1, 2, 3, or 4 modules wide. Code 93 bar codes
contain a mandatory two digits for data integrity.
CHARACTERISTICS
Character Set:
Symbol Length:
Check Digit:
Bi-directional Decoding:
Maximum Density:
128 ASCII character set
Variable
2
Yes
14.8 char./inch (using .0075 inch narrow element)
CHARACTER SET
The following tables represent Code 93 data. Table 1 defines all of the USS-93
character assignments. Table 2 shows the full ASCII character set with the special
control characters.
Table 1. USS-93 Character Assignments
I-1
Table 2. Encoding the Full ASCII Character Set
_
0123456789
I-2
APPENDIX J - SOURCES OF BAR CODE STANDARDS
ABC (American Blood Commission)
1117 North 19th Street
Suite 501
Arlington, VA 22209-1749
(703) 522-8414
*
Committee for Commonality in Blood Banking Automation (CCBBA)
Report (Codabar)
AIM (Automatic Identification Manufacturers, Inc.)
1326 Freeport Road
Pittsburgh, PA 15238
(412) 963-8588
*
*
*
*
*
*
*
USD-1 (Interleaved 2 of 5)
USD-2 (A Subset of Code 39)
USD-3 (Code 39)
USD-4 (Codabar)
USD-6 (Code 128)
USD-7 (Code 93)
USD-8 (Code 11)
AIAG (Automotive Industry Action Group)
26200 Lahser Road
Suite 200
Southfield, MI 48034
(313) 358-3570
*
*
*
AIAG-B-1 1984 Bar Code Symbology Standard
AIAG-B-3 Shipping/Parts Identification Label Standard
AIAG-B-6 Standard for Bar Code Data Identifiers
ANSI (American National Standards Institute)
11 West 42nd Street
New York, NY 10036
(212) 624-4900
*
*
ANSI MH10.8M-1983 Specification for Bar Code Symbols on Transport
Packages and Unit Loads. (Code 39, Interleaved 2 of 5, Codabar)
ANSI X3A1.3 Bar Code Print Quality (Draft)
J-1
DOD (Department of Defense)
Naval Publications & Forms Center
5801 Tabor Avenue
Philadelphia, PA 19120
(215) 697-2000
*
*
*
MIL-STD-1189A (B) - Standard Department of Defense Bar Code
Symbology
MIL-STD-129J - Military Standard - Marking for Shipment & Storage Bar Code Markings
FED-STD-123D - Federal Standard - Marking for Shipment (Civil
Agencies) Bar Code Markings
EAN (European Article Numbering Association)
Rue des Colonies, Bte 8
1000 Brussels
BELGIUM
011 322 218 7585
HIBCC (Health Industry Business Communications Council)
5110 North 40th Street, Suite 250
Phoenix, AZ 85018
(602) 381-1091
*
*
*
HIBC Supplier Labeling Standard
HIBC Provider Applications Standard
HIBC Guidelines
UCC (Uniform Code Council)
8163 Old Yankee Rd., Suite J
Dayton, OH 45458
(513) 435-3870
*
*
*
*
*
UPC Symbol Specification
UPC Location Guidelines
UPC Shipping Container Symbol Specifications Manual
UPC Industrial Code Guidelines Manual
UPC Film Master Verification Manual
J-2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement