Touch Screen Device Driver Software

Touch Screen Device Driver Software
User Manual (Touch Screen Driver)
ITM Inc.
Touch Screen Device Driver Software
User Manual Version 04.01.06
Application Model : L1730SF-SVN, L1730SF-BVN
L1510BF-SVN, L1510SF-SVN
This models support only the USB type.
The software described in this document is provided based on the Software
License Agreement, and can be used only when the contents of the agreement.
Please read the manual before installing the touch screen. If you find the
problem or inconvenience during install and use, make an inquiry of the
custom service team or the sales team.
If you loss driver CD or Update UPDD software, use ‘
’
☞ Information of this manual can be changed without advance notice for performance
improvement.
1
User Manual (Touch Screen Driver)
ITM Inc.
Contents
1.
Introduction
----------------------------------------------
3
2.
Quick Guide
----------------------------------------------
5
3.
Full Guide
----------------------------------------------
6
Installation ----------------------------------------------
6
I.
II. Uninstall
----------------------------------------------
III. Before using the touch screen
11
------------------------
13
IV. UPDD Function Setting -------------------------------
18
V. Support procedures for problem s ----------------------
36
2
User Manual (Touch Screen Driver)
ITM Inc.
1. Introduction
This installation guide provides the information about using the Touch Screen Device Driver
software. Read this guide completely so you can fully utilize the functions of this software.
Features
The software lets you use our touch screen controller, just as though you were using a mouse to
operate the touch screen on Windows.
1. This touch screen software can implement an operating environment equivalent to the
mouse function through operating the touch screen.
2. Because you can use the touch screen software together with a mouse, you can switch
usage between the touch screen and the mouse without needing any special settings.
3. This driver confirms OS's language environment automatically and is installed in this
language. Help of program is supported according to OS's language environment.
4. The touch screen controller only supports USB type connection.
(LG supports only USB type.)
5. The software lets you customize functions such as, changing the preference to left hand
users, setting click controlling for detailed usage , event customization for touch input, and
precise calibration function to insure excellent operability in a wide range of applications.
6. Supports multi-monitors touch function on USB. This software does not support multi
touch, Multi input on a single monitor is not supported.
☞ Multi monitor : Multi monitor function enables more than one users to input on
Touch Screens with interlinking several Touch Screens to one PC,
Input is processed in consecutive order. For example, there is
that keyboard and a mouse are linked at the same time by input
device to one PC.
☞ Dual Touch : Dual touch support means several touch screens are linked to one
PC, and when the screen is given multi input simultaneously
each input is processed at the same time ( This version does not
support such function.)
See on-line multi-monitor documentation for more information.
7. Currently the Touch screen driver supports individual auto touch monitor rotation
between monitor 1 and monitor 2 only when using Intel chips and iRotate software. In
other environments the software supports auto touch monitor rotation for only monitor
1(Main Monitor). (If resolution and rotation of all monitors are equal, user can
manually use touch screen functions with modification)
3
User Manual (Touch Screen Driver)
ITM Inc.
Minimum System Requirements
● Supported model :
- IBM PC/AT or its compatibles
● Supported operating system :
- Windows 2000, Windows XP, Windows VISTA(32, 64BIT)
Remarks
1. Application models are L1730SF-SVN, L1730SF-BVN, L1510BF-SVN, L1510SF-SVN
2. Supports only USB type connection..
3. The software is designed for our touch-screen controller. It is not intended for operation with
touch-screen controllers of other companies or similar products.
4. Please restrict usage methods that are only in this manual. Other methods might not work
with the software.
5. The software is not to be used on OS systems and product models that are not mentioned in
the manual.
6. The program may malfunction when used with mouse emulation programs or similar
software.
7. The driver installation begins with executing file Setup.exe. Running the driver or using
Touch screen functions will not work before installation.
4
User Manual (Touch Screen Driver)
ITM Inc.
2. Quick Guide
1. You must fully install the UPDD program to use the touch screen.
2. After the program is installed, connect the USB cable. UPDD program will recognizes the
device automatically if USB cable is connected after installation.
3. Run the UPDD program.
4. If the UPDD console of the UPDD program appears on the screen when running the
program, click calibration located on the bottom left side of the console. (After the
program is installed, all functions are at basic settings)
5. Touch the calibration marks on the screen to set touch points with corresponding location
6. You can use the touch screen when calibration is complete.
7. When configuring multi monitor environment, visit this site for further instructions.
See on-line multi-monitor documentation for multi screens information.
5
User Manual (Touch Screen Driver)
ITM Inc.
2. Full Manual
I. Installation
Installation of the software differs, depending on whether USB port has been connected to our
touch-screen controller. This section describes the procedures for installation and the parts that
you need to set individually depending on whether you have USB port connected.
1. Computer power supply (common)
1. Turn on the computer and start Windows
2. Insert the CD then the installation will start automatically
(Don’t connect the USB controller)
☞ If the software is not installed, connecting the USB device will trigger Windows to do
an automatic hardware search. But because the controller driver is not installed,
Error will occur during hardware search. So we encourage you to connect the USB
after software installation.
2-1. Start install program (Windows XP/Vista 32bit)
1. Insert the CD then the installation will start automatically.
6
User Manual (Touch Screen Driver)
ITM Inc.
☞ The set values displayed in the installer screen are the optimized for most users
which requires no modification for normal users.
☞ This driver confirms OS's language environment automatically and is installed in this
language.
- During the installation sequence, the screen for selecting the controller will appear. Then, you
must select whether you want to connect your touch-screen controller.
☞ LG application model supports only USB type. So driver is selected by USB type.
- To connect the controller with the USB port, choose [USB].
After selecting [USB], click [Install].
2-2. Start install program (Vista 64bit)
- Microsoft visual C++ 2005 Redistributable (x64) should be installed prior to the system for
UPDD to install in Windows Vista 64bit’s case. User can easily confirm installation by opening
the control panel ‘Change or Remove programs’.
1.
If installed : Follow manual instructions of 2-1 and install program.
2.
In case program is not installed : Open the CD-ROM driver and first open and install file
vcredist_x64.exe and proceed with installation as shown in 2-1.
7
User Manual (Touch Screen Driver)
ITM Inc.
☞ Installation of vista update vcredist_x64.exe requires Administrator account. If the
current user is not the Administrator you are instructed to log off and use the
Administrator account to install program.
1. Choose start of Windows.
2. Execute [Accessories] – [Run].
3. Execute OK after input gpedit.msc.
4. Move to path such as picture.
8
User Manual (Touch Screen Driver)
ITM Inc.
[Local Computer Policy] - [Windows Settings] - [Security Settings] - [Local Policies] - [Security
option] - [Accounts: Administrator account status]
5. Set [Enable] in [Accounts: Administrator account status]
6. After log off, log in to administrator account.
7. Open CD-ROM driver in computer and install vcredist_x64.exe file.
9
User Manual (Touch Screen Driver)
ITM Inc.
3. Install driver
Wait until the install is 100% complete. Click on “Close”, and press the <Enter> key.
☞ USB controller is automatically recognized when it is connected to PC
☞ When the controller is connected to the computer, the name of controller's VID
(Vender ID) shows.
Ex) USB (UPDD-1) or USB (UPDD-2)
☞ If controller is connected for the first time, process about new hardware discovery will
be started. The installation will be done automatically in 5 ~ 10 sec, please wait.
Program installation path : C:\Program Files\UPDD
☞ UPDD setup.exe file executes install only. Therefore, if user wants to remove program,
Turn to page 11 for reference of manaul uninstall (page 11).
☞ Continuous UPDD setup.exe program execution can produce problem.
10
User Manual (Touch Screen Driver)
ITM Inc.
II. Uninstall
There are 2 methods to uninstall this software.
1. Execute Unistall.exe file in folder that UPDD is installed.
2. To uninstall the software, run “My Computer”, then go to the “Control Panel” and select
“Add/Delete Application” and choose the “Universal Pointer Device Driver.” Finally click
“Change/Remove”
11
User Manual (Touch Screen Driver)
ITM Inc.
After activating the Uninstaller, follow the software’s instructions on the screen.
Click on “Uninstall” or press <Enter>
You have successfully completed the uninstall. Click on “Close”.
12
User Manual (Touch Screen Driver)
ITM Inc.
III. Before using the touch screen
1. Calibration
You must calibrate the Touch screen before begin of use.
Calibration : It is very important work that the position of touch corresponds with the
Windows’s mouse cursor position. Through calibration you can use the touch
screen with more accuracy and less frustration.
The followings are a few procedures that are required before calibration.
☞ When running calibration, the program needs time to confirm setting values. (about
10 sec)
Users that have continuous sessions of changing calibration setting values, must
consider this point
1. Setting calibration conditions
1) Click the icon at the task, and select the [Adjust settings]. And select the
[calibration] of UPDD console, see following picture.
2) Change the setting value that User wants.
☞ Condition setting makes reference to [ V. UPDD Function Setting - A) Calibration
setting – 4. Calibration ]
2. Calibration action path
Can select start calibration with any of the following 3 methods..
1) [Start] -> [All Programs] -> [UPDD] -> [Calibration] select.
2) [Start] -> [All Programs] -> [UPDD] -> [Adjust settings] -> [Calibration] select.
13
User Manual (Touch Screen Driver)
ITM Inc.
3) UPDD system tray icon of monitor screen right side lower column clicks ->
[Calibration] select.
☞ If controller is not connected, calibration and test of system tray will be deactivated
and cannot be able to select.
3. Executing Calibration
- If you execute calibration, ╋ mark will appear on the screen and touch this using a pen or finger.
After touching the first ╋ mark, another ╋ mark will appear on the screen, Touch this point as
done with the first point. (╋ mark’s number will appear as many times as you have set set under
calibration condition.)
Press center of mark
with finger or a pen.
- If you finish pressing calibration points, the value is stored automatically and position calibration
action is completed.
- Calibration cancellation has 2 methods. Method selection depends on which procedure the user is
currently at.
1) ESC key cancel : When changing calibration conditions or when executing calibration Esc key
14
User Manual (Touch Screen Driver)
ITM Inc.
allows you to return to the stage calibration execution.
2) Time out cancel : If time runs out during the calibration the program will set the calibration
conditions to the previous condition.
☞ If the coordinates differ as time passes please calibrate again
☞ The calibration procedure sends out more data than usual to the computer.
Therefore for more accurate touch results we recommend you to choose the [Click
and Drag] for correct calibration, and slowly and precisely touch the calibration
marks.
☞ In case of executing calibration in multi monitor environment, each controller and
monitor must be matched up. If controller is connected first time, the computer will
use the default values which is the whole area of monitor 1. Therefore, without
matching monitor settings the screen will only show calibration on monitor 1
Ex) USB controller 1 – monitor 1, USB controller 2 – monitor 2.
☞ In case of executing calibration in multi monitor environment, user must make
resolution of all monitors equally. Because UPDD bases resolution of the basis
monitor, calibration screen can project smaller larger images than the monitor.
Therefore, executing calibration in equal resolution, and change each by resolution
that user wants.
☞ When executing calibration, calibration coordinate is depended on absolute
magnitude of size of touch screen. After calibration, even if the user changes
resolution of monitor, coordinates are calculated automatically and are applied.
2. Mouse setting
1. Clicking and dragging
You can use the touch screen to perform such basic operations as click, double-click and drag as
follows:
Click
: Touch the touch screen swiftly.
Double-click : Touch the touch screen twice swiftly
Drag
: Drag your finger (or stylus) on the screen.
2. Right-clicking the mouse
- Unlike the mouse, the touch screen does not provide two buttons. When you want to perform
the right-button operation using the touch screen, do the following:
1) Click the icon at the task, and select the [Event selector]. A small window with a
computer mouse appears.
2) Every time you touch the mouse picture, a dark blue mouse button becomes active.
3) Touching the touch screen just after the active button appears; operate it like a mouse
button.
15
User Manual (Touch Screen Driver)
Left Button
ITM Inc.
Right Button
☞ If [one hit] of event selector menu is selected, return by left button action after action
1th.
4) If click event selector icon of system tray, can do action such as 1). A red mouse
button becomes action.
3. Multi-monitor and multi-device notes
UPDD supports both multi-monitor and multiple pointer device configurations. This means that
UPDD can cater with a system that has more than one monitor or more than one pointer device
and any combination thereof can be supported by UPDD.
This document describes the multi-monitor and device considerations for each of the supported
desktop operating systems.
Please ensure you read the notes section before using multi touch devices or multi touch
monitors.
1. Current UPDD supports limited multi environment on the primary monitor (monitor 1).
– resolution, monitor area, rotate etc.
1) We only currently support rotate on monitor 2 with Intel Chips and iRotate utility.
All other environments only support functions on Primary (monitor 1) monitor.
2) Monitor number can select from Moniter1 to Monitor16.
2. Monitor and controller connection confirmation in multi monitor environment.
1) To use multi monitor functions the user must check if all monitors are correctly
connected.
2) When initially connecting the first controller in multi monitor environment the
desktop area should be set to default values.(Monitor1)
16
User Manual (Touch Screen Driver)
ITM Inc.
3)
If the user does not configure the connection of monitor and controller, calibration
screen shows only in monitor 1. You can calibrate the monitor and controller’s
connection after the connection. The monitor and controller connection is decided
according to the order that controller is connected to PC.
Ex) First controller 1, Second controller 2 -> Monitor 1 – controller 1 and Monitor 2
– controller 2
First controller 2, Second controller 1 -> Monitor 1 – controller 2 and Monitor 2 –
controller 1
4) User must confirm connection state between monitor and controller in multi monitor
environment.
5) After confirming the order of port and Hub that the controller is coupled, Accord the
controller and monitor
Ex)
3. Calibration in multi Monitor environment.
1) Because calibration screen of present UPDD executes on resolution of basis monitor
(monitor 1), calibration screen can look smaller or bigger than the monitor’s
optimized resolution.
2) When executing calibration work in multi monitor environment, the user should set
resolution of all monitors equally and begin the calibration.
3) If the user completes the calibration, the change of resolution that user wishes to use
will not affect the coordinates of the touch screen, because the controller will
automatically set all coordinates to the changed resolution.
4) For reference, UPDD only currently supports rotate on monitor 2 with Intel Chips
and iRotate utility. All other environments only work on Primary (monitor 1)
monitor. So, error can occur.
5) When all monitors are rotating state such as basis monitor, the user can use manual
control for the calibration
☞ In Multi monitor environment, the calibration must be executed after setting
conditions equally with basis monitor.
☞ UPDD works mainly on a basic monitor condition. And other monitors are set for
assistance monitor.
17
User Manual (Touch Screen Driver)
ITM Inc.
IV. Setting UPDD Function
- By the default, this software provides the environment similar the ordinary mouse-operating
environment. Its flexible customize functions facilitates the operating environment which meets a
specific application. This section describes [Control setting] which allows you to make various
settings.
A) Activating the Adjust setting screens
Use one of the following methods:
1. Select and activate “START” → [Program (P)] → [UPDD] → [Control setting.]
2. Click the icon at the system tray (see the right picture), and select and activate the [Control
setting].
-
The ‘touch screen driver property’ window appears. The screen is divided by several tabs.
These tabs are classified for each purpose of setting. They are gathered into one screen for
each content respectively; the controller addition is in the [Device] tab, the controller status
confirmation is in the [Status tab], and the contents related to calibration is in the
[Calibration] tab.
-
☞ When you change the setting, it re-initializes the controllers so that the touch screen
gives no response for several seconds.
18
User Manual (Touch Screen Driver)
ITM Inc.
1. Hardware
- Hardware port definition, desktop association, add, remove and search for devices
z
1)
Shows the desktop area controller by the pointer device. This is normally set to the
whole desktop. In multi-monitor environment this option is used to associate the device to
a specific monitor.
☞ After select desktop area, user must calibrate for application.
☞ In case connecting and using more than one monitors, confirm order of each monitor
in PC display registration information first. And select monitor in Handling Whole
desktop control setting.
☞ After selecting monitor, user must execute calibration and accord connection
between monitor and controller so that touch screen will work normally. (First time
controllers are connected all controllers are set to default value (monitor 1).
Desktop area select.
z
1)
Monitor 1 ~ Monitor 16
- In case use multi monitor, can select monitor to do matching with controller of touch
screen. Monitor number can confirm in Display settings of Windows, and Monitor number
can select from Moniter1 to Moniter16. (When use multi monitor, controller of number
19
User Manual (Touch Screen Driver)
ITM Inc.
such as number of monitor has to be connected.)
☞ Monitor and controller’s connection are decided according to order that controller is
connected to PC.
Ex) First controller 1, Second controller 2 -> Monitor 1 – controller 1 and Monitor
2 – controller 2.
First controller 2, Second controller 1 -> Monitor 1 – controller 2 and Monitor
2 – controller 1.
☞ Usually, USB's order is decided by system (PC main board).
z
Shows the port connected to the device.
- In the case of USB, PS/2 and Bus connected devices this shows connection information.
z
In a multi-device environment this option is used to add additional devices, specifically non
PnP devices.
☞ UPDD adds automatically if USB controller is connected. So, user does not have to
execute [Add a new device].
20
User Manual (Touch Screen Driver)
ITM Inc.
z
User can remove the current device. When all devices are removed, [Properties] does not
act.(All environment values are initialized.)
☞ When controller is use impossibility, controller name is marked color red.
☞ Device remove icon is executed in state that cancels USB controller and PC's
connection. Because driver adds controller automatically, even if remove controller
in situation that is linked, controller is added again immediately. So though
controller’s connection is canceled, it can execute icon.
☞ Connected controller name (ID) is marked in device tab of the UPDD console top
position.
☞ When several controllers are connected, you can select each controller in device tap
of the UPDD console.
21
User Manual (Touch Screen Driver)
ITM Inc.
2. Click mode
- The Click Mode dialog defines the click mode emulation and links to the click mode settings
within the operating system.
z
Shows the current click mode emulation. A full mouse click is the action of a pen down
followed by a pen up. In the following click emulations, where pen down is specified but with
no indication if it’s a left or right click, then the Event Selector setting will dictate the click
performed.
z
Pen down then drag. Pen up at lift off.
z
Drag then click at lift off.
z
Pen down and pen up at point of touch. No movement.
22
User Manual (Touch Screen Driver)
ITM Inc.
z
At normal ‘Click and drag’ settings the user can add the mouse right click function. If the user
presses on the screen for the time that interactive switch delay is set, the mouse right click
function will occur..
z
Interactive switch delay determines the time the mouse right click should occur.
(User can confirm the execution speed by animation. But, if cancel touch before animation
ends, function call is cancelled too.)
z
Visual notification indicates if visual feedback is shown during Interactive Touch right click
countdown (only Windows at time of writing).
z
Indicates if touch is silent. If disabled a beep is sent to the system internal speaker (not sound
card). The system must have an internal speaker configured and working.
☞ Disabled if the OS, such as Vista 64 bit, does not support the speaker interface used
by UPDD.
☞ Confirmation Path
[Start] – [control Panel] – [Hardware and Sound] – [Device Manager] – [Tool bar :
View] – [Show hidden devices] – [Non-plug and Play Drivers] – [Beep] check.
☞ UPDD uses the system internal speaker (Beep sound).
z
The user can go to [Mouse configuration] and set mouse settings to fit user preference.
23
User Manual (Touch Screen Driver)
ITM Inc.
z
Used to test right and double clicks. A red check is shown if the click test is successful to the
click mode settings within the operating system.
☞ Use this icon to click test only. It does not relate to the event selector.
24
User Manual (Touch Screen Driver)
ITM Inc.
3. Properties
- Define device name, configuration, priority (when multiple devices defined) and specific
settings.
☞ Wrong setting can make problem in touch screen action. Therefore, we recommend
touch screen function manual setting for only advanced users.
z
Associates a name to the device. By default the name is the driver’s controller device name.
z
Applies a filter to produce smoother drawing. Software implementation of a low pass filter
algorithm to remove jitter. This is a more advanced approach to filtering that can improve
drawing but will affect the speed of drawing the higher the value used. The scope is possible
from 0 to 100. (Default : 5)
z
The Lift off Time value specifies the time interval required to register a stylus lift after the last
touch packet is received. Lift off time is defined in units of 20ms. This value is used to perform
25
User Manual (Touch Screen Driver)
ITM Inc.
a pen up if the ‘Use Lift off’ packet is disabled otherwise Pen ups are generated as soon as the
stylus leaves the pointer device display. However, because this timer is triggered after each
received touch packet it is important to ensure the value is greater than the time interval
between data packets otherwise pen up events will constantly be generated. If this value is set
to zero pen ups based on time are disabled. This is a useful setting for controllers working in
Delta mode, that is, data is not generated unless the x or y co-ordinates change. The scope is
possible from 0 to 100. (Default : 5)
z
Stabilization causes small movements to be ignored. The scope is possible from 0 to 100.
(Default : 0)
z
Applies a filter to produce smoother drawing. Averaging takes the average of the last N coordinates. This is a very basic approach to filtering that can improve drawing and not affect
drawing speed. The scope is possible from 0 to 100. (Default : 0)
z
The device can only be used if no other device is in use (i.e. touch screen being touched) and
the time since the last use of another device exceeds the ‘release time’ period. Release time is
defined in units of 20ms and defaults to 20ms.
z
Any device currently in use is forced into a ‘pen up’ state and the device is given immediate
priority.
z
Defines the interlock release time, as described above. The scope is possible from 0 to 100.
(Default : 5)
z
Only shown if a pen up data packet is generated by the device on stylus lift off. If enabled the
pen up data packet is used to invoke pen up otherwise the pen up processing will generate a
pen up event at the lift off time threshold as described above.
26
User Manual (Touch Screen Driver)
ITM Inc.
☞ When select or cancel, need the time for data transmission.
z
The Anchor Mouse option is set if the mouse cursor is to return to its original position after the
pointer device has been used. Normally used in multi-monitor configurations where the cursor
is to return to another monitor.
☞ Anchor position is set to place that is located on last by a PC mouse.
z
Indicates if the device is enabled. If the device is disabled the hardware port’s resources are
available for use by another device or process. This is a way of freeing up the resources
without having to uninstall the driver. If UPDD has a connection to the device it cannot be
‘stopped’ until disabled by UPDD.
z
All properties function value return to defaults. Is initialized controller's properties which is
selected in device tap of UPDD console.
☞ Keep in mind that all properties values are initialized.
27
User Manual (Touch Screen Driver)
ITM Inc.
4. Calibration
- The calibration dialog is used to set the calibration settings for the current device.
- Calibration cancellation has 2 methods. User can select any method according to return to
visual point.
1) ESC key cancel : Return before calibration practice.(only calibration cancel)
2) Time out cancel : Return before changing by calibration setting.(Cancel until Calibration
setting Value.)
☞ After making any calibration setting change you should wait a few seconds before
calibrating otherwise the previous settings are used in the calibration.
☞ In case of executing calibration in multi monitor environment, user must make
resolution of all monitors equally. Because UPDD bases resolution of basis monitor,
calibration screen can appear smaller or larger than the monitor’s optimized
resolution. Therefore, execute calibration in equal resolution, and then change the
resolution of each monitor to the settings that the user wants.
☞ When executing calibration, calibration coordinates are depended on absolute
magnitude of size of touch screen. After calibration, even if user changes resolution
of monitor, coordinate is calculated automatically and is applied.
z
Shows/selects the current calibration style. Each device can have more than one calibration
28
User Manual (Touch Screen Driver)
ITM Inc.
style which can be calibrated independently. Calibration styles can be invoked/switched from
an application, a toolbar or the UPDD activator.
e.g. a whiteboard device may be used as a whiteboard or in projected mode to show a large
desktop. Two calibration modes can be defined, whiteboard and projected and calibrated
when used in those modes. The appropriate calibration style can then be invoked when
required, thus avoiding the need to constantly recalibrate when switching usage.
z
Add a new calibration style. After add style, must execute revision.
z
Indicates the number of calibration points. The number of points determines the calibration
pattern used. 2 points uses the raw pointer device data, 4, 9 and 25 uses a calibration algorithm
best suited to non-linear data whereas the other patterns are best suited to linear data. Using 4
points or more allows the driver to automatically determine the orientation of the touch screen
and caters for rotated video in cases where the driver has not automatically adjusted for
rotation and for these reasons it is highly recommended that 4 points or more are used.
(Default : 4)
z
Indicates the percentage margin in from the edge of the visual display area from which to draw
the calibration points. The scope is possible from 1 to 25. (Default : 12)
z
Specifies the number of seconds to wait for a calibration touch before cancelling the calibration
procedure. The scope is possible from 1 to free time. Because error by system frequency use
can happen, it recommends to use within 20 seconds. There is addition time at actuality action.
(Default : 20)
z
If enabled a calibration check dialog is shown at the end of the calibration procedure. The
calibration confirm button must be selected (with the touch screen!) if the new calibration data
is to be used.
29
User Manual (Touch Screen Driver)
ITM Inc.
z
If enabled a beep will be generated on calibration touch.
☞ Disabled if the OS, such as Vista 64 bit, does not support the speaker interface used
by UPDD.
☞ Confirmation Path
[Start] – [control Panel] – [Hardware and Sound] – [Device Manager] – [Tool bar :
View] – [Show hidden devices] – [Non-plug and Play Drivers] – [Beep] check.
☞ UPDD uses the system internal speaker (Beep sound).
30
User Manual (Touch Screen Driver)
ITM Inc.
5. Status
- Device status and re-initialisation, test functions, driver reload and settings backup.
z
Shows the actual controller type in use irrespective of the name given to it in the UPDD
Console.
z
Indicates if the device is enabled at the UPDD level. The enabled setting is held in the UPDD
Console or, for Windows, the UPDD system tray. Applications can also enable or disable the
device using the UPDD programming interface.
z
This function reinitializes the controller. The macro, if defined, is sent to the controller.
☞ In case execute [Replay initialization macro], communication happens between
controller and UPDD driver. If execute command consecutively, program can be
31
User Manual (Touch Screen Driver)
ITM Inc.
stopped by communication clash. So, caution user to do not run repeat.
☞ If UPDD program is stopped, do re-booting.
z
This option resets the sync error count. Only enabled if error count >0.
z
This function reloads the driver. This could take a number of seconds to perform.
☞ In case execute [Reload driver settings], communication happens between controller
and UPDD driver. If user executes the commands consecutively, program can be
stopped by communication clash. Caution not to repeat run.
☞ If UPDD program is stopped, do re-booting.
z
32
User Manual (Touch Screen Driver)
ITM Inc.
z
z
Dump driver settings to a file. The file is useful for support purposes but can also be used in
subsequent installs to define the initial settings.
- Windows Vista path C:\Users\User Accounts
- Windows XP path C:\Documents and settings\User Accounts
- file type ; 19112008120040.ini(min, hour, year, month, day)
☞ Dump file becomes initialization data at subsequent installation. Therefore,
initialization value of subsequent installation can be different from manual.
Contemplate in use.
33
User Manual (Touch Screen Driver)
ITM Inc.
B) Event selector
- Using the Event Selector allows you to classify the left and right clicking of the mouse button.
1. Activating the Event Selector
- Select “Start” → [Program(P)] → [UPDD] → [Event Selector].
Or click the icon at the system tray (see the right picture), and select and activate the
[Event Selector].
2. Settings
- To select the Event Selector, click a small mouse picture at the left top of the window, and
select a menu displayed.
One hit
: Enables only once touch in the right-click setting.
Small icon
: Displays a smaller size mouse picture in Windows.
Medium icon
: Displays the standard size mouse picture in Windows.
Large Icon
: Displays a larger size mouse picture in Windows.
Text mode
: Provides text display in Windows. One hit:
Enables only once touch in the right-click setting.
Auto run
: Provides text display in Windows. One hit:
Enables only once touch in the right-click setting.
☞ Displayed language is decided according to Windows OS language.
☞ Can be changed partially.
34
User Manual (Touch Screen Driver)
ITM Inc.
C) System Tray menu
- If click system tray's icon, can use function of menu such as following picture.
Enabled
: Indicates if the device is ‘logically’ enabled/disabled in UPDD. If a
device is ‘physically’ disabled (e.g. a device is unplugged) the text will
be shown in red. A tick indicates that the device is enabled and a cross
indicates that it is disabled. This option can be used to temporarily
disable the pointer device. If more than one device is configured a sub
menu lists the devices to show the enabled state. If all devices are
disabled or inactive the system tray icon shows a red X to indicate to
the user the touch screen will not be working.
Calibrate
: Invokes the calibration procedure.
Adjust settings
: Invokes the UPDD Console.
Test
: Invokes the Test Utility.
Event Selector
: Invokes the Event Selector:
Help
: Invokes the UPDD Help system.
About
: General information.
☞ If controller is not connected, calibrate and test function cannot use.
35
User Manual (Touch Screen Driver)
ITM Inc.
V. Support procedures for problem
☞ Please check below before calling
1. Do not install in Windows Vista 64bit..
z
After install first Visual C++ runtime library (vcredist_x64.exe) through Windows update in
Windows Vista 64 bit, and must install device driver program(UPDD).
2. Installation language is English.
z
z
This driver confirms OS's language environment automatically and is installed in this language.
UPDD's basic language is English. Therefore, English installation screen can happen in Os of other
language. If install reference the manual, there is no problem.
3. During installation, [new hardware search program] is executed continuously.
z
z
Before software is installed, Windows hardware search program acts automatically in case connect
controller to USB. But because controller driver is not installed yet, Windows hardware search
program mistake happens. So encourage to connect USB after software installation.
If message appears during UPDD installation, cancel controller connection. And UPDD ends
installation. Connect controller after installation completion, and becomes hardware addition
automatically.( In case is not selected by automatic addition, user must answer on hardware
addition message.)
4. There is no remove option when setup.exe is executed after full installation
z
z
z
The driver has separate setup and uninstall files.
The user can uninstall at [control panel -> add/remove programs]
The user can execute uninstall at the UPDD folder.
5. Not able to remove device in UPDD console.
z
You can only use the remove device icon when the USB controller and PC connection is
disconnected. Because the present driver automatically adds the USB controller when connected, to
prevent continuous device adding the icon is activated only when the USB controller is
disconnected
6. Touch screen does not work properly.
z
z
z
Make sure that the software is installed properly.
Check the interface cable connection.
- USB controller : USB cable.
Try reconnecting the interface cable.
7. Touched area and the on-screen cursor does not match.
z
Try reconfiguring the calibration.
8. Double click does not act.
36
User Manual (Touch Screen Driver)
z
z
z
ITM Inc.
Confirm setting of software click mode.
Confirm setting in event selector Windows.
This phenomenon can appear in case of the double click awareness speed is so fast or dimension is
small.
9. Can not hear anything even when silent mode is not selected.
z
z
z
z
UPDD uses the system internal speaker (Beep sound).
Indicates if touch is silent. If disabled a beep is sent to the system internal speaker (not sound card).
The system must have an internal speaker configured and working.
Disabled if the OS, such as Vista 64 bit, does not support the speaker interface used by UPDD.
Confirmation Path : [Start] – [control Panel] – [Hardware and Sound] – [Device Manager] – [Tool
bar : View] – [Show hidden devices] – [Non-plug and Play Drivers] – [Beep] check.
10. Executed [Reload driver settings] consecutively and program is stopped.
z
z
In case execute [Reload driver settings], communication happens between controller and UPDD
driver. If execute command consecutively, program can be stopped by communication clash. So,
caution user to do not run repeat.
If UPDD program is stopped, do re-booting.
11. Mouse cursor moves to fixed direction continuously.
z
Please Communicate to ITMinc. (
)
12. Different point touches but mouse cursor always same position come back.
z
Please Communicate to ITMinc. (
)
13. In case use resolution as is different in multi monitor, there is problem with
calibration screen.
● Because calibration screen of present UPDD executes on resolution of basis monitor (monitor 1),
calibration screen can look like smaller or big than monitor.
● When execute calibration work in multi monitor environment, set resolution of all monitors equally
and calibration work.
● After complete calibration work, may change by resolution that user wishes to use because regulate
coordinate and resolution of touch screen automatically even if resolution is changed.
14. Executed whole calibration in multi monitor environment. But, calibration screen
displays in monitor 1.
z
z
In case connect and use many monitor, confirm order of each monitor in PC display registration
information first. And select monitor in Handling Whole desktop control setting First time
connected all controllers is set by default value (monitor 1)
Ex) First controller 1, Second controller 2 -> Monitor 1 – controller 1 and Monitor 2 – controller 2
First controller 2, Second controller 1 -> Monitor 1 – controller 2 and Monitor 2 – controller 1
15. Each monitor and touch screen do not correspond in multi monitor environment.
z
z
z
In case connect and use many monitor, confirm order of each monitor in PC display registration
information first. And select monitor in Handling Whole desktop control setting First time
connected all controllers is set by default value (monitor 1)
Monitor number can select from Moniteo1 to Moniteo16.
Monitor and controller’s connection are decided according to order that controller is connected to
PC.
37
User Manual (Touch Screen Driver)
ITM Inc.
Ex) First controller 1, Second controller 2 -> Monitor 1 – controller 1 and Monitor 2 – controller 2.
First controller 2, Second controller 1 -> Monitor 1 – controller 2 and Monitor 2 – controller 1
User must confirm connection state between monitor and controller in multi monitor environment.
After confirm order of port and Hub that controller is coupled, Accord controller and monitor.
z
z
Ex)
16. Rotated monitor 2 in multi monitor environment, there is problem with touch position
and calibration screen.
z
Currently we only support rotate on monitor 2 with Intel Chips and iRotate utility. All other
environment only work on Primary (monitor 1) monitor.
When all monitors are rotating state such as basis monitor, can use manual control the calibration.
z
17. Confirming program uninstall completion message is difficult.
z
z
z
According to priority order, the displayed position (front, or behind) of program is decided.
Windows program decides automatically priority order of program that is acting.
When uninstall dialog is not displayed, confirm [Uninstall Complete] message in taskbar of monitor.
18. Please make reference to the following homepage.
.
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement