98-05271 R0 UK IC18 Spreader

98-05271 R0 UK IC18 Spreader
IC18 SPREADER
JOB COMPUTER
U S E R
Software version 1.05
European, Volume Based
M A N U A L
COPYRIGHTS
© 2011 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described in it may be reproduced,
copied, photocopied, translated, or reduced in any form or by any means, electronic or machine readable, recording or otherwise, without
prior written consent from TeeJet Technologies.
TRADEMARKS
Unless otherwise noted, all other brand or product names are trademarks or registered trademarks of their respective companies or
organizations.
LIMITATION OF LIABILITY
TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED. NO COPYRIGHT LIABILITY OR PATENT IS ASSUMED. IN NO EVENT SHALL TEEJET TECHNOLOGIES BE LIABLE FOR
ANY LOSS OF BUSINESS, LOSS OF PROFIT, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS, OR FOR INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS BEEN ADVISED OF
SUCH DAMAGES ARISING FROM TEEJET TECHNOLOGIES SOFTWARE.
To ensure optimal use of the equipment, please read this manual thoroughly. Please contact TeeJet Technologies Customer Support or an
authorized TeeJet Technologies dealer if additional support is required.
RESPONSIBILITY FOR USE OF THIS PRODUCT
Regarding responsibility for use of this product, we refer to our sales and delivery terms which states:
Product Usage
Any use of the product is at the sole risk of the buyer. The buyer is therefore not entitled to any form for compensation caused by, for
example, any of the following:
►Disturbance to/from any electronic services or products that do not conform to the standards for CE marketing;
►Missing or poor signal coverage or a succession hereof from external transmitters/receivers used by the buyer; Functional faults which
apply to or from a PC-program or PC equipment not delivered by the seller;
►Faults that may arise from the buyers’ negligence to react to warnings and fault messages from the product or that can be traced to
negligence and/or absent constant control of the work carried out in comparison to the planned job.
When implementing any new equipment the buyer must take great care and pay attention. Any doubts as to the correct operation/use
should result in contacting the seller’s service department.
ISOBUS Job Computer : IC18 Spreader European
Table of Contents
CHAPTER 1– PRODUCT OVERVIEW
OPTIONAL SYSTEM COMPONENTS
1
1
CHAPTER 2 – GETTING STARTED
3
START UP
3
CALCULATION MODE
3
PAGE LAYOUT AND NAVIGATION
4
Home Screen....................................................................................................................................................................4
Transport Mode................................................................................................................................................................4
Operation Mode................................................................................................................................................................4
Main Setup Mode..............................................................................................................................................................5
Main Setup Menu Icons and Section Overviews....................................................................................................6
CHAPTER 3 – MAIN SETUP
7
CALCULATION MODE
7
MAIN SETUP MODE OVERVIEW
7
Main Setup Screen................................................................................................................................................................................. 8
Master Screen.......................................................................................................................................................................................... 8
Home Screen............................................................................................................................................................................................ 9
COUNTERS9
GETTING STARTED
JOB PARAMETERS
OVERVIEW
Trip Counters..........................................................................................................................................................................................10
Active Trip Counter...............................................................................................................................................10
Area Counter........................................................................................................................................................10
Distance Counter..................................................................................................................................................10
Time Counter........................................................................................................................................................10
Amount.................................................................................................................................................................10
Campaign Counters.............................................................................................................................................................................10
Area Counter........................................................................................................................................................10
Amount Counter....................................................................................................................................................10
Time Counter........................................................................................................................................................10
Total Counters........................................................................................................................................................................................11
Area Counter........................................................................................................................................................ 11
Amount Counter.................................................................................................................................................... 11
Time Counter........................................................................................................................................................ 11
Export Counters....................................................................................................................................................................................11
12
SETUP
Active Trip Counter...............................................................................................................................................12
Application Rate....................................................................................................................................................12
Tonnage................................................................................................................................................................12
Gate Height...........................................................................................................................................................12
Density..................................................................................................................................................................12
MACHINE13
APPENDIX
OPERATION
Filling.........................................................................................................................................................................................................13
Amount Remaining...............................................................................................................................................13
Full Bed.................................................................................................................................................................13
Operation................................................................................................................................................................................................14
Speed Source.......................................................................................................................................................14
Simulated Speed..................................................................................................................................................14
Implement Parameters.......................................................................................................................................................................14
98-05271 R0 UK
i
ISOBUS Job Computer : IC18 Spreader European
Working Width.......................................................................................................................................................14
Fast Empty Bed RPM...........................................................................................................................................14
Master Switch.......................................................................................................................................................14
Calibrations.............................................................................................................................................................................................15
Volume Per Pulse...........................................................................................................................................................15
Manual Calibration................................................................................................................................................15
Automatic Calibration............................................................................................................................................15
Implement Speed Sensor...............................................................................................................................................16
Manual Calibration................................................................................................................................................16
Automatic Calibration............................................................................................................................................16
Alarm Configurations..........................................................................................................................................................................16
Amount Remaining Alarm On/Off..........................................................................................................................16
Amount Remaining Trigger Level..........................................................................................................................16
CAN Speed Source Timeout.................................................................................................................................16
Active Trip Count Information................................................................................................................................16
OEM...........................................................................................................................................................................................................17
USER INTERFACE
18
Use Preferred VT..................................................................................................................................................18
COMMUNICATION18
HELP19
Diagnostic...............................................................................................................................................................................................19
Test Input........................................................................................................................................................................19
Test Output.....................................................................................................................................................................20
Test PWM Dutycycle.............................................................................................................................................20
VT Data...........................................................................................................................................................................20
TECU..............................................................................................................................................................................20
About........................................................................................................................................................................................................20
CHAPTER 4 – OPERATION MODE
21
EUROPEAN OR NORTH AMERICA CALCULATION MODE
21
OPERATION MODE OVERVIEW
21
OVERVIEW
Keys Descriptions...........................................................................................................................................................21
Section and Icon Descriptions........................................................................................................................................21
Master Screen........................................................................................................................................................................................22
Home Screen..........................................................................................................................................................................................22
GETTING STARTED
START/STOP APPLICATION
23
INFORMATION KEY
24
TRANSPORT MODE
24
APPENDIX A - FACTORY SETTINGS & RANGES
25
APPENDIX B - UNIT SPECIFICATIONS
26
SETUP
OPERATION
APPENDIX
ii
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
CHAPTER 1– PRODUCT OVERVIEW
Congratulations on the purchase of your new IC18 Spreader ECU built on the ISOBUS architecture. When used within the guidelines of
the this manual, the IC18 controller will be a reliable application tool.
This manual covers the European functions of the IC18 ECU. For North America functions, see manual number 98-05173.
Use with your existing VT or the Matrix 570VT for dry product application
• Works seamlessly and displays on any ISOBUS VT
• Easy navigation menu and data rich display
• Add additional ISOBUS ECUs as your needs change
• Provides basic rate control or variable rate if the connecting VT has variable rate task control capabilities
• Standardized plugs, cables and software simplify installation and connectivity and result in true “plug and play” technology. IC18 ECU
resides on the implement, reducing hardware in the cab
Figure 1-1: IC18 Job Computer
OPTIONAL SYSTEM COMPONENTS
Matrix 570VT
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
The Matrix 570VT is a simple to operate, ISOBUS-certified 5.7″ color touch screen display suitable for bright daylight and nighttime
operation
Figure 1-2: Matrix 570VT
98-05271 R0 UK
1
ISOBUS Job Computer : IC18 Spreader European
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
2
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
CHAPTER 2 – GETTING STARTED
• A firm touch is required when selecting a screen icon.
• Settings are NOT automatically saved when selected. The ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to the previous menu.
• The console needs to be cycled off and back on when changing or attaching equipment to the system.
• The menu structure on your display might vary from the one displayed in this User Manual depending on the virtual terminal being
used.
START UP
Power is continuously supplied to the job computer. The virtual terminal will give access to the job computer options and operation.
Figure 2-1: Master Screen
Matrix VT Setup Key
IC18 Spreader
Other options as available on
ISOBUS system
Master Screen Key
CALCULATION MODE
GETTING STARTED
OVERVIEW
The IC18 job computer is programed to calculate calibrations based on European or North American methods.
◄European – Gate Height is NOT calculated into the product application and calibrations will be based on volume per pulse.
◄North America – Gate Height is calculated into the product application and calibrations will be based on pulses per volume.
This setting has been established before leaving the factory, but it can be changed after purchase with assistance from TeeJet
Technologies Customer Service or your local dealer through the OEM setup menu options.
Figure 2-2: European
SETUP
Figure 2-3: North America
98-05271 R0 UK
APPENDIX
OPERATION
This manual discusses
specifically the functions
and options in European
Mode. See the specific
IC18 Spreader: North
America User Manual for
functions and options in
North America Mode.
3
ISOBUS Job Computer : IC18 Spreader European
PAGE LAYOUT AND NAVIGATION
The Master Screen gives access to the systems currently available on your VT. From the Master Screen, the Home Screen gives access
to the IC18’s available functions.
Home Screen
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and Main Setup.
Figure 2-4: Home Screen
Operation Mode
Main Setup Mode
Transport Mode
Fill Bed Access Key
Master Screen Key
Quick View
Information Based on Current Active Trip
Transport Mode
While in Transport Mode, all operation functions are locked off and cannot be activated.
Figure 2-5: Transport Mode
Home Key
Speedometer
OVERVIEW
Master Screen Key
Operation Mode
GETTING STARTED
Information on the Operation screen will vary depending on the parameters set by the user and the OEM.
Figure 2-6: Operation Mode
Count Number
Applied Volume
Cnt
Alert Warning
1
Applied Area
298.2 t
SETUP
0.0
Speed/Application Information
500
kg/m
Remaining Bed Contents
1.14 ha
kg/ha
1 3 11
Home Key
Information Key
Start/Stop Key
OPERATION
Application On/Off Indication
Rolr
RPM
APPENDIX
Roller RPM
4
www.teejet.com
Spnr
0
RPM
Spinner RPM
0
Extra Key Spaces
Master Screen Key
ISOBUS Job Computer : IC18 Spreader European
Main Setup Mode
The main setup menu contains six options. Each of these options either directly access settings or additional menus.
Figure 2-7: Main Setup Screen
Home Key
Back One Screen
Forward One Screen
Up One Selection
Down One Selection
Master Screen Key
The table below outlines the additional menus and directs you to the setup pages for further information.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
|
|
|
|
Job Parameters
Machine
User Interface
Communication
Help
Trip
Filling
Diagnostic
Campaign
Operation
About
Total
Export Counters
Implement Parameters
Pulses per Volume
Implement Speed Sensor
– Calibrations
Alarm Configurations
OEM
– Sensors
Actuators
Bed Size
User Interface (VT)
Regulator
Configuration
Calibration RPM
Program Modes
Reference Gate Height
Clear total counters
OPERATION
SETUP
GETTING STARTED
OVERVIEW
The OEM setup menu is password protected and the settings in this menu are
directly related to the fitted OEM equipment.
APPENDIX
NOTE: Select functions may not be visible due to OEM settings, available
equipment or sensors.
98-05271 R0 UK
5
ISOBUS Job Computer : IC18 Spreader European
Main Setup Menu Icons and Section Overviews
Figure 2-8: Enter Selection Screens
Selection
Slide Bar with Decrease One Selection
and Increase One Selection Arrows
Accept Key
Escape Key
Number Pad
Close Number Pad Key
Range Maximum
Range Minimum
Zoom In Key
Zoom Out Key
Open Number Pad Key
Available Selections
Up One Selection
Accept Key
Escape Key
Down One Selection
OVERVIEW
GETTING STARTED
SETUP
OPERATION
Section or Icon
Description
Section or Icon
Description
Accept Key
Accepts the new selection
Selection
Displays the current or new selection
Close Number Pad
Key
Minimizes the number pad
Slider
Slide to the left to decrease or right to
increase the selection
Decrease One
Selection Arrow
Decreases the setting
Slide Bar
Down One
Selection Arrow
Highlights the selection below
Escape Key
Escapes without saving changes
Selects the setting by pressing and
releasing on the slide bar or pressing and
dragging the Slider to a designated value.
Range for a specific setting is displayed on
the slide bar.
Increase One
Selection Arrow
Increases the setting
Up One Selection
Arrow
Highlights the selection above
Number Pad
Use the numbers to set the selection value
Zoom In
Key
Narrows slide bar range. Gray = maximum
zoom level.
Open Number Pad
Key
Maximizes the number pad
Zoom Out
Key
Expands slide bar range. Gray = minimum
zoom level.
APPENDIX
6
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
CHAPTER 3 – MAIN SETUP
Main Setup Mode configures the Counters, Job Parameters, Machine, User Interface, Communication and Help options.
NOTE:The menu structure on your display might vary from the one displayed in this User Manual depending on the virtual
terminal being used.
CALCULATION MODE
The IC18 job computer is programed to calculate calibrations based on European or North American methods.
◄European – Gate Height is NOT calculated into the product application and calibrations will be based on volume per pulse.
◄North America – Gate Height is calculated into the product application and calibrations will be based on pulses per volume.
This setting has been established before leaving the factory, but it can be changed after purchase with assistance from TeeJet
Technologies Customer Service or your local dealer through the OEM setup menu options.
Figure 3-1: European
This manual discusses specifically the functions and options in European Mode. See the specific IC18 Spreader: North America User
Manual for functions and options in North America Mode.
MAIN SETUP MODE OVERVIEW
Figure 3-2: Main Setup Screen
Home Key
Back One Screen
OVERVIEW
Forward One Screen
Up One Option
GETTING STARTED
Down One Option
|
Counters
(pages xx-xx)
MAIN SETUP MODE MENU STRUCTURE
|
|
|
|
|
Job Parameters
(pages xx-xx)
Machine
(pages xx-xx)
User Interface
(pages xx)
Communication
(pages xx)
Help
(pages xx-xx)
Trip
Filling
Diagnostic
Campaign
Operation
About
Total
Implement parameters
Pulses per Volume
Implement Speed Sensor
– Calibrations
Alarm configurations
OPERATION
Export Counters
SETUP
Master Screen Key
OEM
APPENDIX
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM equipment. Refer to the OEM Setup Manual for information
regarding OEM settings.
98-05271 R0 UK
7
ISOBUS Job Computer : IC18 Spreader European
Main Setup Screen
NOTE: Settings are NOT automatically saved when selected. The ACCEPT KEY must be selected to save the setting. Select the
ESCAPE KEY to escape without saving settings and return to the previous menu.
To access the Main Setup screens:
1. Select IC18 JOB SPREADER KEY
from the Master Screen.
2. Select MAIN SETUP SCREEN KEY
from the Home Screen.
3. Select from:
►Counters – used to provide an overview of various system counters:
◄ Trip – used to display information regarding area, distance, time and amount applied.
◄ Campaign – used to display information regarding area, amount applied and time for all trips
◄ Total – used to display information regarding area, amount applied, and time for all activity
◄ Export Counters – allows counter information to be exported in HTML or CSV format
►Job Parameters – used to configure application settings including trip counter, application rate, tonnage, gate height and density:
►Machine – used to configure machine settings:
◄ Filling – establishes the amount of material remaining in the tank.
◄ Operation – establishes Speed Source, and Simulated Speed
◄ Implement Parameters – establishes the Working Width, Fast Empty Bed RPM and Master Switch location
◄ Calibrations – establishes either manual or automatic settings of the sensors
◄ Alarm Configurations – establishes alarms on or off as well as sets their trigger level
◄ OEM – the OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM
equipment. Refer to the OEM Setup Manual for information regarding OEM settings.
►User Interface – used to allow the operator to select the system virtual terminal (VT) if more than one VT is available on the ISOBUS
CAN:
►Communication – used to establish the IC18's ability to communicate with an external computer:
►Help – allows the operator to choose between Diagnostics and the About screen:
◄ Diagnostic – used to troubleshoot input/output of the controller (sensor or actuator).
◄ About – used to provide information on the console such as software version, build number, etc
NOTE: The menu structure on your display might vary from the one displayed in this User Guide depending on the virtual terminal being
used. This User Guide will display all possible options.
Master Screen
The Master Screen gives access to the systems currently available on your VT.
• To view the Master Screen options, select MASTER SCREEN KEY
in bottom right corner of any screen.
OVERVIEW
Figure 3-3: Master Screen
GETTING STARTED
SETUP
OPERATION
APPENDIX
8
www.teejet.com
Master Screen Key on Main Setup Screen
ISOBUS Job Computer : IC18 Spreader European
Home Screen
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and Main Setup.
• To view the Home Screen, select HOME KEY
in the top right corner of any screen.
Figure 3-4: Home Screen
Home Key on Main Setup Screen
COUNTERS
The Counters Menu provides an overview of various system counters including Trip Counters, Campaign Counters and Total Counters.
From this screen one can also Export Counters.
|
Counters
|
Job Parameters
MAIN SETUP MENU
|
Machine
|
User Interface
|
Communication
|
Help
Trip
Campaign
Total
Export Counters
OVERVIEW
GETTING STARTED
1. From the Main Setup Screen , select COUNTERS.
2. Select from:
►Trip – used to display information regarding area, distance, time and amount
applied
►Campaign – used to display information regarding area, amount applied and
time for all trips
►Total – used to display information regarding area, amount applied, and time
for all activity
►Export Counters – allows counter information to be exported in HTML or
CSV format
Figure 3-5: Counters
APPENDIX
OPERATION
SETUP
NOTE: Settings are NOT automatically saved when selected. The
ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to
the previous menu.
98-05271 R0 UK
9
ISOBUS Job Computer : IC18 Spreader European
Trip Counters
Trip Counters displays information regarding area, distance, time and amount
applied. The trip that is active is displayed/active on the Operations Screen.
Figure 3-6: Trip Counters Menu
Active Trip Counter
One of up to ten (10) Active Trip Counters can be selected to view the desired trip
information. The trip that is “active” is displayed/active on the Operation Screen.
• To select the Active Trip Counter, use the number pad or slide bar.
• To clear the Trip Counters, select TRASH CAN KEY
. A confirmation
screen will be displayed.
Area Counter
Displays applied area for the selected Active Trip.
Distance Counter
Displays distance traveled for the selected Active Trip.
Figure 3-7: Confirm Counter Clearance
Time Counter
Displays time traveled for the selected Active Trip.
Amount
Displays amount of material applied during the selected Active Trip.
Campaign Counters
Campaign Counters display information regarding area, amount applied and time
for all trips.
• To clear the Campaign Counters, select TRASH CAN KEY
. A confirmation Figure 3-8: Campaign Counters
screen will be displayed.
Area Counter
Displays total applied area for all trips.
Amount Counter
Displays total amount of material applied during all trips.
Time Counter
Displays total time traveled for all trips
OVERVIEW
Figure 3-9: Confirm Campaign Clearance
GETTING STARTED
SETUP
OPERATION
APPENDIX
10
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
Total Counters
Total Counters displays information regarding area, amount applied, and time for all Figure 3-10: Total Counters
activity. Total Counters can only be cleared in the OEM menu.
Area Counter
Displays total applied area for all trips. Total Counters cannot be cleared.
Amount Counter
Displays total amount of material applied during all trips. Total Counters cannot be
cleared.
Time Counter
Displays total time traveled for all trips Total Counters cannot be cleared.
Figure 3-11: Export Counters
SETUP
GETTING STARTED
OVERVIEW
Figure 3-12: Confirm Export Counters
OPERATION
Export Counters allows counter information to be exported in HTML or CSV format.
HTML files can be viewed from an internet browser. CSV files can be viewed as
Excel sheets.
• To export a HTML file, select HTML KEY
. A confirmation screen will be
displayed.
• To export a CSV file, select CSV KEY
. A confirmation screen will be
displayed.
For data transfer, an optional cable is required. Contact your local dealer for
additional information.
APPENDIX
Export Counters
98-05271 R0 UK
11
ISOBUS Job Computer : IC18 Spreader European
JOB PARAMETERS
Job Parameters configures application settings. Options include Active Trip Counter, Application Rate, Tonnage, Gate Height and Density.
|
Counters
1. From the Main Setup Screen
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
, select JOB PARAMETERS.
|
Communication
Figure 3-13: Job Parameters
NOTE: Settings are NOT automatically saved when selected. The
ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to
the previous menu.
Active Trip Counter
Active Trip Counter selects one of up to ten (10) active trip counters to view the
desired trip information. The trip that is “active” is displayed/active on the Operation
Screen.
• To select the Active Trip Counter, use the number pad or slide bar.
NOTE: The selected trip counter will have all data modified (added too) when
additional operations are activated. If current trip counter is not cleared,
Figure 3-14: Tonnage On
the new data will be added to the existing data.
Application Rate
Application Rate defines a target rate of product being applied per hectare/acre.
This setting will set the same for all active trips. Range is 0 - 9999 kg/ha.
• To select the Application Rate, use the number pad or slide bar.
Tonnage
Tonnage converts pounds/kilograms to tons. It is used when the application rate
exceeds the number of digits allowed on the screen display.
• To select the tonnage mode, select an option from the drop down menu or use
the UP/DOWN ARROWS to highlight the option.
Gate Height
Gate Height is the height of the gate opening. Range is 0.0 - 99.9 cm.
• To select the gate height, use the number pad or slide bar.
OVERVIEW
Density
Density is the weight of the material being applied. Range is 0.00 - 5.00 kg/l
• To select the density, use the number pad or slide bar.
GETTING STARTED
SETUP
OPERATION
APPENDIX
12
www.teejet.com
|
Help
ISOBUS Job Computer : IC18 Spreader European
MACHINE
Machine configures machine settings. Options include Filling, Operation, Implement Parameters, Calibrations, Alarm Configurations and
OEM.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
|
Communication
|
Help
Filling
Operation
Implement parameters
Pulses per Volume – Calibrations
Implement Speed Sensor
Alarm configurations
OEM
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM equipment.
1. From the Main Setup Screen , select MACHINE.
2. Select from:
►Filling – establishes the amount of material remaining in the bed.
►Operation – establishes Speed Source, and Simulated Speed.
►Implement Parameters – establishes the Working Width, Fast Empty Bed
RPM and Master Switch location.
►Calibrations – establishes either manual or automatic settings of the
sensors.
►Alarm Configurations – establishes alarms on or off as well as sets their
trigger level
►OEM – The OEM setup menu is password protected and the settings in this
menu are directly related to the fitted OEM equipment. Refer to the OEM
manual for information regarding OEM settings.
Figure 3-15: Machine
NOTE: Settings are NOT automatically saved when selected. The ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to the previous menu.
Filling establishes the amount of material remaining in the bed.
NOTE: The size of the tank is established in the OEM menu. This is the number
that will repopulate when the Full Bed Key
is pressed.
Figure 3-16: Filling
OVERVIEW
Filling
GETTING STARTED
Amount Remaining
Actual Content displays the current volume of content in the tank.The volume can
be manually adjusted.
• To adjust the volume, use the number pad or slide bar.
APPENDIX
OPERATION
SETUP
Full Bed
Full bed returns the amount remaining value to the maximum volume of the bed.
• To reset the Amount Remaining value, press the FULL BED KEY
.
98-05271 R0 UK
13
ISOBUS Job Computer : IC18 Spreader European
Operation
Operation establishes Speed Source and Simulated Speed.
Figure 3-17: Operation
Speed Source
Speed Source selects whether to base the machine’s speed on input from the
CAN, an Implement or a Simulated source. Selecting “Implement” will allow for
the configuration of pulses per 100 meters. Selecting “Simulated” will allow for
simulated speed to be entered using the “Edit Value” option. Selecting “CAN”
allows for speed being supplied by the ISOBUS CAN (usually from the TECU) to be
used.
• To select the Speed Source, select an option from the drop down menu or use
the UP/DOWN ARROWS to highlight the option.
NOTE: If “Implement” is selected, refer to the Calibrations section for further
instructions.
Simulated Speed
Simulated Speed establishes a speed to be used when using the Simulated Speed
source.
• To select the Simulated Speed, use the number pad or slide bar.
Figure 3-18: Implement parameters
Implement Parameters
Implement Parameters establishes the the Working Width, Fast Empty Bed RPM
and Master Switch location.
Working Width
Working Width establishes the desired distance between each adjacent pass while
spreading.
• To select the Working Width, use the number pad or slide bar.
Fast Empty Bed RPM
Fast Empty Bed RPM establishes the revolutions per minute of the roller used to
drive the conveyor during the Fast Empty.
• To select the RPM, use the number pad or slide bar.
The availability of Fast Empty is established in the OEM menu under Program
Modes. When set to "On", the Fast Empty Key
will be available on the Home
Screen.
OVERVIEW
GETTING STARTED
Master Switch
Master Switch is used to allow the operator to choose between a “remote master”
switch or the Start/Stop Key.
• To select the Master Switch, select an option from the drop down menu or use
the UP/DOWN ARROWS to highlight the option.
SETUP
OPERATION
APPENDIX
14
www.teejet.com
Figure 3-19: Fast Empty Key
ISOBUS Job Computer : IC18 Spreader European
Calibrations
Figure 3-20: Calibrations
Calibrations establishes either manual or automatic settings of the sensors.
NOTE: For specific calibration options to appear, a specific sensor needs to be
installed. Sensor availability is activated on the Sensor Presence screen in
the OEM section.
Volume Per Pulse
Volume Per Pulse establishes the amount of cubic centermieters per one (1) pulse.
This value can be established manually or calibrated automatically. Each type of
spreader has a variety of variables that factor into the volume per pulse number
(roller diameter, sensor type, type of belt or chain, etc.). The volume per pulse
number factors these variables into the spreader output
Manual Calibration
Manual calibration establishes the volume based on a user entered value.
• To select the Pulses per Volume, use the number pad or slide bar.
Figure 3-21: Pulses per Volume
Automatic Calibration
Automatic calibration establishes the volume using the automatic calibration
function.
• To calibrate the pulses per volume, select CALIBRATION KEY
.
• Follow the series of instructions displayed.
NOTE: Material will be dispensed during this procedure. Be sure that a collection
device is in place so that a proper volume can be determined.
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
Figure 3-22: Calibration Step One
98-05271 R0 UK
15
ISOBUS Job Computer : IC18 Spreader European
Implement Speed Sensor
The Implement Speed Sensor establishes the wheel pulses over a specified
distance. This value can be established manually or calibrated automatically.
Figure 3-23: Calibrations
Manual Calibration
Manual calibration establishes the pulses based on a user entered value.
• To select the Pulses per Distance, use the number pad or slide bar.
Automatic Calibration
Automatic calibration establishes the pulses using the automatic calibration
function.
• To calibrate the pulses per distance, select CALIBRATION KEY
.
• Follow the series of instructions displayed.
• Select the ACCEPT KEY
to complete the calibration
The counted wheel pulses will be displayed during the automatic calibration.
Figure 3-24: Implement Speed Sensor
Alarm Configurations
Alarm Configurations establishes alarms on or off as well as sets their trigger level.
Amount Remaining Alarm On/Off
The Amount Remaining Alarm will appear if the hopper amount has reached the
low limit level entered. Select either “On” to activate the alarm, or “Off” to deactivate
the alarm.
• To select the Amount Remaining Alarm mode, select an option from the drop
down menu or use the UP/DOWN ARROWS to highlight the option.
Amount Remaining Trigger Level
Amount Remaining Trigger Level establishes the low limit that will trigger the
Amount Remaining Alarm.
• To select the Amount Remaining Trigger Level, use the number pad or slide
bar.
OVERVIEW
CAN Speed Source Timeout
CAN Speed Source Timeout establishes the number of seconds the system will
continue to run on CAN speed without receiving CAN input before the alarm
triggers.
• To select the CAN Speed Source Timeout time, use the number pad or slide
bar.
GETTING STARTED
Active Trip Count Information
The Active Trip Count Information Alarm will appear on power up to identify to
the user which trip counter is active and that this specific counter will be used for
storing work data. Select either “On” to activate the alarm, or “Off” to deactivate the
alarm.
• To select the Active Trip Count Information alarm mode, select an option from
the drop down menu or use the UP/DOWN ARROWS to highlight the option.
SETUP
OPERATION
APPENDIX
16
www.teejet.com
Figure 3-25: Alarm Configurations
ISOBUS Job Computer : IC18 Spreader European
OEM
The OEM setup menu is password protected and the settings in this menu are directly related to the fitted OEM equipment. To obtain an
access code, contact your local dealer or TeeJet Technologies Customer Service.
To access the OEM screens:
Figure 3-26: Machine to OEM
1. From the Main Setup Screen , select MACHINE.
2. Select OEM.
3. Select the Access Code Entry Box to the right of the menu option.
4. Use the number pad or slide bar to enter the access code.
5. Select the ACCEPT KEY
to complete the unlock process
6. Select from:
►Sensors – used to establish the parameters for Spinner RPM, Spinner RPM
Revolution, Hydraulic Motor RPM Revolution, and Weighing systems
►Actuators – used to select the type of valve used to control the spreader belt
►Bed Size – used to establish the maximum load capacity of the spreader
►User Interface (VT) – used to establishes the displayed tolerance for
application rate
►Regulator Configuration – used to establish:
◄ Regulator Test – used to verify the regulation control matches theory
and actual settings.
◄ Valve Configuration – sets the control settings for the regulation valve.
◄ PID Parameters – sets the course and fine adjustments of the
regulation valve.
►Calibration RPM – used to program the desired roller RPM, the bed chain
speed, used during the calibration process
►Program Modes – used to designate various options that impact system
Figure 3-27: OEM Unlock
functions including program style, calibration type, flow factor, step
persentage and fast empty
►Reference Gate Height – used to establish the actual gate height used
during the calibration process
►Delete Total Counters – used to clear the Total Count system counter for
Area, Volume and Time
APPENDIX
OPERATION
SETUP
GETTING STARTED
OVERVIEW
NOTE: Settings are NOT automatically saved when selected. The
ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to
the previous menu.
98-05271 R0 UK
17
ISOBUS Job Computer : IC18 Spreader European
USER INTERFACE
User Interface allows the operator to select the system virtual terminal (VT) if more than one VT is available on the ISOBUS CAN.
|
Counters
1. From the Main Setup Screen
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
|
Communication
|
Help
Figure 3-28: User Interface
, select USER INTERFACE.
NOTE: Settings are NOT automatically saved when selected. The
ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to
the previous menu.
Use Preferred VT
Use Preferred VT sets the virtual terminal preference to either on or off. If “On” is
selected, the preferred VT will be used. If “Off” is selected, the system will arbitrarily
select which VT to use (if more than one VT is available on the ISOBUS CAN).
NOTE: This should always be set to "off" unless another VT is on the CAN bus.
• To set the Use Preferred VT mode, select an option from the drop down menu
or use the UP/DOWN ARROWS to highlight the option.
COMMUNICATION
Communication establishes the IC18's ability to communicate with an external computer.
|
Counters
1. From the Main Setup Screen
OVERVIEW
GETTING STARTED
SETUP
OPERATION
APPENDIX
18
www.teejet.com
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
, select COMMUNICATION.
|
User Interface
|
Communication
|
Help
Figure 3-29: Communication
ISOBUS Job Computer : IC18 Spreader European
HELP
The Help menu allows the operator to choose between Diagnostics and the display of information about serial number, CAN BUS
information, etc. These menus are typically accessed upon Customer Service personnel request only.
|
Counters
MAIN SETUP MODE MENU STRUCTURE
|
Job Parameters
|
Machine
|
User Interface
|
Communication
|
Help
Diagnostic
About
1. From the Main Setup Screen , select HELP.
2. Select from:
►Diagnostic – used to troubleshoot input/output of the controller (sensor or
actuator).
►About – provides information on the console such as software version, build
number, etc.
Figure 3-30: Help
NOTE: Settings are NOT automatically saved when selected. The
ACCEPT KEY
must be selected to save the setting. Select the
ESCAPE KEY
to escape without saving settings and return to
the previous menu.
Diagnostic
Diagnostic is used to troubleshoot input/output of the controller (sensor or actuator). Figure 3-31: Diagnostic
►Test Input – displays the input high and low values on the installed sensors.
►Test Output – allows the regulation valve to be tested at different percentages of
dutycycle..
►VT – provides information regarding the virtual terminal controller.
►TECU – provides information regarding the TECU.
Test Input
OVERVIEW
Test Input displays the input high and low values on the installed sensors.
• To reset the sensors to "0",
select TRASH CAN KEY
.
APPENDIX
OPERATION
SETUP
GETTING STARTED
Figure 3-32: Test Input
98-05271 R0 UK
19
ISOBUS Job Computer : IC18 Spreader European
Test Output
Test Output allows the regulation valve to be tested at different percentages of
dutycycle.
Figure 3-33: Test Output
Test PWM Dutycycle
Liquid Valve PWM Dutycycle is used to test the regulating valve at different
percentages of dutycycle.
• To set the percentage, use the number pad or slide bar.
• Press the PLUS/MINUS KEYS
to test the regulation valve at the
specified dutycycle percentage increase/decrease.
VT Data
The Virtual Terminal (VT) menu provides information regarding the virtual terminal
controller (i.e., address version, etc.).
• If more terminals/controllers are used, switch between these by pressing the
GO TO NEXT VT KEY
.
• Press the DELETE OBJECT POOL KEY
to force the VT to delete saved
data and upload new information from the IC18 Job Computer on the next
power cycle.
NOTE: Restart the IC18 Job Computer to implement and display changes.
Figure 3-34: VT Data
TECU
The TECU is a control unit, residing on the tractor, that performs basic functions
such as power handling, speed info, etc. The TECU data are displayed on this
page.
Figure 3-35: TECU
OVERVIEW
GETTING STARTED
About
The About screen provides information on the IC18 such as software version, build Figure 3-36: About
number, etc. This information may become useful in case of technical support.
SETUP
OPERATION
APPENDIX
20
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
CHAPTER 4 – OPERATION MODE
The Operation Screen accesses the working aspects of the IC18 including boom section control, rate control and trip/count/
application information.
NOTE: Settings are automatically saved when selected.
NOTE:The menu structure on your display might vary from the one displayed in this User Manual depending on the virtual
terminal being used.
EUROPEAN OR NORTH AMERICA CALCULATION MODE
The IC18 job computer is programed to calculate calibrations based on European or North American methods.
◄European – Gate Height is NOT calculated into the product application and calibrations will be based on volume per pulse.
◄North America – Gate Height is calculated into the product application and calibrations will be based on pulses per volume.
This setting has been established before leaving the factory, but it can be changed after purchase with assistance from TeeJet
Technologies Customer Service or your local dealer through the OEM setup menu options.
OPERATION MODE OVERVIEW
Information on the Operation screen will vary depending on the parameters set by the user and the OEM.
Figure 4-1: Operation Mode Screen Overview
Count Number
Applied Volume
Cnt
Alert Warning
1
Applied Area
298.2 t
0.0
Speed/Application Information
500
kg/m
Remaining Bed Content
1.14 ha
kg/ha
1 3 11
Home Key
Information Key
Start/Stop Key
Application On/Off Indication
Rolr
RPM
Roller RPM
Spnr
0
RPM
0
Extra Key Spaces
Master Screen Key
Spinner RPM
Keys Descriptions
Home Key
Press to return to the Home Screen
Information Key
Press to toggle between display modes
Start/Stop Key
Press to start or stop spreader
OVERVIEW
Description
GETTING STARTED
Icon
Description
Job Information
This information bar displays the active count number,
applied volume and applied area
Count Number
Displays the current active trip or job number
Applied Amount
Displays amount applied for the selected count number
Applied Area
Displays applied area for the selected count number
1
0 t
0.00 ha
Displays vehicle speed or amount applied per minute or RPM.
The Information Key toggles
between display modes.
APPENDIX
Speed/Application
Information
Cnt
OPERATION
Section or Icon
SETUP
Section and Icon Descriptions
98-05271 R0 UK
21
ISOBUS Job Computer : IC18 Spreader European
Section or Icon
Description
Remaining Bed Contents Displays the remaining bed content
NOTE: If no bed sensor is fitted or the contents are not entered in the Filling Menu prior to spraying, Bed
Contents will display “0”.
Application Rate
Displays the actual application rate per hectare/acre
NOTE: When the Master is “On” the actual application rate per hectare/acre will be displayed. When the
Master is “Off” the target rate is displayed.
Alarm
Displayed if an alarm condition is active
Roller RPM
Displays the RPM of the belt roller
Spinner RPM
Displays the RPM of the spinner
Master Screen
The Master Screen gives access to the systems currently available on your VT.
• To view the Master Screen options, select MASTER SCREEN KEY
in bottom right corner of any screen.
Figure 4-2: Master Screen
Master Screen Key on Operation Mode Screen
Cnt
1
298.2 t
0.0
1.14 ha
500
kg/m
kg/ha
1 3 11
Rolr
Spnr
RPM
0
RPM
0
Home Screen
The Home Screen gives access to the IC18’s available functions: Operation Mode, Transport Mode and Main Setup.
• To view the Home Screen, select HOME KEY
in the top right corner of any screen.
Figure 4-3: Home Screen
Home Key on Operation Mode Screen
OVERVIEW
Cnt
1
298.2 t
0.0
1.14 ha
500
kg/m
kg/ha
1 3 11
GETTING STARTED
Rolr
RPM
SETUP
OPERATION
APPENDIX
22
www.teejet.com
Spnr
0
RPM
0
ISOBUS Job Computer : IC18 Spreader European
START/STOP APPLICATION
Figure 4-4: Spraying Stopped
Cnt
1
298.2 t
1.14 ha
0.0
500
kg/m
kg/ha
1 3 11
Rolr
Spnr
RPM
0
0
RPM
Figure 4-5: Spraying Started
Cnt
1
298.2 t
0.0
1.14 ha
500
kg/m
kg/ha
1256
Spnr
RPM
0
OVERVIEW
0
GETTING STARTED
RPM
SETUP
Rolr
OPERATION
.
APPENDIX
Starting/stopping application is controlled using the Start/Stop Keys.
• To start or stop the application, press the START/STOP KEYS
98-05271 R0 UK
23
ISOBUS Job Computer : IC18 Spreader European
INFORMATION KEY
Information Key toggles the Speed/Application Information section on the Operation Screen between the display modes.
• Vehicle speed
• Volume applied per minute
• Target Roller RPM
Figure 4-6: Information Key
Cnt
1
298.2 t
1.14 ha
0.0
Vehicle speed
500
km/h
kg/ha
1 3 11
Cnt
1
Spnr
0
0R.P0M
Rolr
Volume applied per minute
RPM
298.2 t
1.14 ha
0
kg/m
500
kg/ha
1 3 11
Cnt
1
Rolr
Ta r g e t
RPM
298.2 t
0
Target Roller RPM
1.14 ha
Spnr
0
RPM
500
RPM
0
kg/ha
1 3 11
Rolr
RPM
Spnr
0
RPM
0
OVERVIEW
TRANSPORT MODE
GETTING STARTED
While in Transport Mode, all operation functions are locked off and cannot be activated. Transport Mode displays the speed in analogue
mode.
Figure 4-7: Transport Mode
Home Key
►Gives access to the IC18’s available functions: Operation Mode,
Transport Mode and Main Setup
Speedometer
SETUP
OPERATION
Master Screen Key
►Gives access to the systems currently available on your VT
APPENDIX
24
www.teejet.com
ISOBUS Job Computer : IC18 Spreader European
APPENDIX A - FACTORY SETTINGS & RANGES
JOB PARAMETERS
Description
Factory Setting
Range/Options
User Setting
Active Trip Counter
1
1 - 10
1
2
3
4
5
6
7
8
9
10
Application Rate
0.0 lb/ac
0.0 kg/ha
0.0 - 9999 lb/ac
0.0 - 9999 kg/ha
Tonnage
Off
Off
On
Gate Height
4.0 in
10.0 cm
0.0 - 35.0 in
0.0 - 99.9 cm
Density
0 lb/ft3
0.00 kg/l
0 - 300 lb/ft3
0.00 - 5.00 kg/l
Description
Factory Setting
Range/Options
Amount Remaining
16000 lb
8000 kg
0 - 90000 lb
0 - 45000 kg
Description
Factory Setting
Range/Options
Speed Source
CAN
CAN
Implement
Simulated
Simulated Speed
0.0 mile/h
0.0 km/h
0.0 - 99.9 mile/h
0.0 - 99.9 km/h
Description
Factory Setting
Range/Options
Working Width
40.0 ft
12.2 m
0.0 - 290.0 ft
0.0 - 90.0 m
Fast Empty Bed RPM
50 RPM
0 - 9999 RPM
Master Switch
Console
Remote
Console
MACHINE
Filling
User Setting
OVERVIEW
Operation
GETTING STARTED
User Setting
Implement Parameters
APPENDIX
OPERATION
SETUP
User Setting
98-05271 R0 UK
25
ISOBUS Job Computer : IC18 Spreader European
Calibrations
Pulses per Volume
Description
Factory Setting
Range
Pulses per Volume
0.0 /ft
0.0 /cm3
0.0 - 5000 /ft
0.0 - 1500.0 /cm3
Description
Factory Setting
Range
Pulses per Distance
0 ft
0m
0 - 30000 /300 ft
0 - 40000 /100 m
Description
Factory Setting
Range/Options
Amount Remaining Alarm On/Off
Off
On
Off
Amount Remaining Trigger Level
0 lb
0 kg
0 - 9000 lb
0 - 4500 kg
CAN Speed Source Timeout
4 sec
0 - 999 sec
Active Trip Count Information
Off
On
Off
Spinner RPM Alarm On/Off
Off
On
Off
Spinner RPM Trigger Level
0 RPM
0 - 9999 RPM
Description
Factory Setting
Options
Use Perferred VT
Off
Off
On
3
User Setting
3
Implement Speed Sensor
User Setting
Alarm Configurations
User Setting
USER INTERFACE
OVERVIEW
APPENDIX B - UNIT SPECIFICATIONS
GETTING STARTED
Dimensions
19.05 x 18.42 x 6.03 cm
Weight
0.644kg
Connector
30 position Cinch pins. A1-K3
30 position Cinch pins. L1-Y3
Environmental
Operating
-40 to +85°C
Humidity
90% non-condensing
SETUP
Input/Output
ISO 11783 (ISOBUS)
Power Requirement
<9 watts @12 VDC
OPERATION
APPENDIX
26
www.teejet.com
User Setting
I C18 S P R E A D E R
J O B CO M P U T E R
U S E R
M A N U A L
Software Version 1.05
European, Volume Based
TeeJet Technologies
1801 Business Park Drive
Springfield, Illinois 62703 USA
Tel: (217) 747-0235 • Fax: (217) 753-8426
www.teejet.com
98-05271 R0 UK
© TeeJet Technologies 2011
TeeJet Aabybro
Mølhavevej 2
DK 9440 Aabybro
Denmark
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement