Digiplex LCD Keypad User`s Manual
Digiplex LCD Keypad
DGP-641
User’s Manual
1.0 TABLE OF CONTENTS
INTRODUCTION ........................................... 6
1.1 Legend .............................................................. 6
BASIC OPERATION ..................................... 7
2.1
2.2
2.3
2.4
2.5
2.6
Auditory Feedback (Beep Tones) ..................... 8
Keypad Indicator Lights .................................... 8
LCD Screen ...................................................... 8
User Menu ....................................................... 10
Partitioned System ........................................... 11
Area Status Display ......................................... 11
ARMING ....................................................... 13
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Exit Delay Timer .............................................. 13
Regular Arming ................................................ 13
Stay Arming ..................................................... 14
Instant Arming .................................................. 15
Force Arming ................................................... 16
One-Touch Buttons .......................................... 18
Keyswitch Arming ............................................ 19
Auto-Arming ..................................................... 19
Bypass Programming ...................................... 20
DISARMING ................................................. 23
4.1 Entry Delay Timer ............................................ 23
4.2 Disarming an Armed System ........................... 23
4.3 Alarm Memory Display ..................................... 25
ACCESS CODES ......................................... 26
5.1
5.2
5.3
5.4
Keypad Lock-out .............................................. 26
Erasing Access Codes .................................... 26
System Master Code ....................................... 27
User Access Codes ......................................... 27
TROUBLE DISPLAY .................................... 33
6.1 Event Record Display ...................................... 38
ADDITIONAL FEATURES ........................... 40
7.1
7.2
7.3
7.4
7.5
7.6
Programmable Outputs (PGMs) ...................... 40
Keypad Settings .............................................. 40
Set Time & Date .............................................. 42
Programming Chime Zones ............................. 42
Panic Alarms ................................................... 44
Quick Function Buttons .................................... 45
FIRE AND BURGLAR ALARMS ................. 46
8.1
8.2
8.3
8.4
8.5
8.6
Standard Fire Zone .......................................... 46
Delayed Fire Zone ........................................... 46
Fire Safety Tips ............................................... 49
Minimizing Home Fire Hazards ....................... 49
Home Fire Warning System ............................ 50
Burglar Alarm ................................................... 50
TESTING AND MAINTENANCE .................. 51
9.1
9.2
9.3
9.4
Burglar Alarm Testing ...................................... 51
Fire Alarm Testing ............................................ 51
System Maintenance ....................................... 51
System Test...................................................... 52
SYSTEM CHECKLIST ................................. 53
10.1 Zone Description.............................................. 53
10.2 Access Codes ................................................. 56
10.3 Special Buttons and Features ......................... 60
10.4 Other Information ............................................ 61
2.0 INTRODUCTION
Your Digiplex™ Security System is an advanced technology
security system that will provide you with reliable security
protection and powerful features that are easy to use. The
elegant and user-friendly Digiplex LCD Keypad will allow you
easy access to your security system's functions and information
at the touch of a button. The 32-character LCD screen will
display messages and menus to guide you through the system’s
operations. Your installer can even customize the messages for
your home or business.
Since you will communicate your instructions to your system
through the keypad, please read this manual carefully and have
your installer explain basic system operation.
2.1 LEGEND
Indicates a warning or an important note.
Indicates useful information or tip.
[WORD]
[NUMBER]
keypad.
Indicates information that must be entered on the
Italics
Indicates references to features, options or sections.
6 User’s Manual
3.0 BASIC OPERATION
Everything you need to know about your security system is
clearly displayed on the large LCD screen. The menus and the
prompt on the LCD screen provide simple, step-by-step
instructions on how to use your system and display what is
occurring in your system. The following sections will introduce
you to the roles of the buttons, the lights, and messages on your
Digiplex LCD Keypad.
Figure 2-1: Basic Overview
Digiplex LCD Keypad’s 7
3.1 AUDITORY FEEDBACK (BEEP TONES)
When you enter information on the keypad, the keypad will guide
you with beep tones to communicate acceptance or rejection of
your entries.
Confirmation Beep: When an operation (i.e. arming/disarming)
is successfully entered or when the system switches to a new
status/mode, the keypad emits an intermittent beep tone (“BEEPBEEP-BEEP-BEEP-BEEP”).
Rejection Beep: When the system reverts to previous status, or
when an operation is incorrectly entered, the keypad emits a tone
(“BEEEEEEEEEEP”).
3.2 KEYPAD INDICATOR LIGHTS
The state of the two colored lights on the keypad (see Figure 2-1
page 7) represents a specific condition in your system.
3.3 LCD SCREEN
The LCD (liquid crystal display) is a 32-character screen that
communicates messages, instructions, and the status of your
system. The backlight, contrast, and scrolling speed are
adjustable (see section 8.2). Your installer can customize many of
the messages to suit your needs.
8 User’s Manual
3.3.1 Normal Mode
When no actions are being performed on the keypad, the keypad will
remain in Normal Mode as shown in Figure 2-2 on page 9 and will
automatically display:
•The current status of the zones for every area the keypad is
assigned
•The Alarm Memory Display (see section 5.3) if any alarms have occurred
•The Trouble Display (see section 7.0) if any troubles are occurring
•The current state of the Indicator Lights
Figure 2-2: Normal and Confidential Mode
3.3.2 Confidential Mode
The installer can program keypads not to display the status of your system
automatically by changing the LCD screen to Confidential Mode. In
Confidential Mode:
• The zones and status messages will NOT be displayed
• The Indicator Lights will not illuminate
• Depending on how your keypad was programmed by the installer,
you must either press a button or enter your User Access Code to
illuminate the Indicator Lights and activate Normal Mode.
Digiplex LCD Keypad’s 9
3.4 USER MENU
Once you enter your User Access Code and are granted access to
the system, the LCD screen will display the User Menu as shown in
Figure 2-3. From this menu you can access various features and
other menus. Depending on the User Options programmed on your
User Access Code, you will have access to some or all of the
features and menus in the User Menu.
Press the desired Action Button (see Figure 2-1, page 7), or
scroll through the menu by using the
and
buttons on
the right of the keypad and press the
button. Once you
have completed an action (i.e. arming, disarming, etc.), the LCD
screen will return to Normal Mode.
Figure 2-3: User Menu
10 User’s Manual
3.4.1 Multiple-action
The Multiple-action feature permits you to complete more than one action
after entering the User Menu. If your installer has enabled this feature, the
LCD screen will return to the User Menu after each action so you may
perform another action without having to re-enter your User Access Code.
Press the
button to exit the User Menu.
3.5 PARTITIONED SYSTEM
Your installer can design your system to recognize up to four
separate protected areas. A separated system is called a
Partitioned System, which can be useful in situations where
shared security systems are more practical. For example, a
company that has both an office area and a warehouse area can
arm and disarm each area separately and control the access to
each area. Therefore, one person may have access to only one
area, whereas another person may have access to all areas.
Access to the areas is determined by the User Access Code.
3.6 AREA STATUS DISPLAY
In Area Status Display you will be able to see the status of the
areas in a Partitioned System (see section 3.5) for the area(s) the
keypad is assigned. If your LCD screen is in Confidential Mode
(see section 3.3.2), you must first press a button or enter your
User Access Code to activate Normal Mode depending on how
your keypad is programmed.
Digiplex LCD Keypad’s 11
How do I see the status of the zones?
1) Enter [ACCESS CODE] then press the button corresponding to
the area:
= Area 1
= Area 3
= Area 2
= Area 4
2) Press
to exit.
In Area Status Display the following will scroll on the LCD
screen:
• “ready” if all zones in the selected area are closed
• “not ready” if zones in the selected area are open
• open zones within that area
• “Trouble(s)” (see section 7.0) if a trouble has occurred
• “Alarms in Memory” (see section 5.3) if an alarm has occurred
12 User’s Manual
4.0 ARMING
When the system is armed, the alarm system will respond to any
breach in the zones according to the zone’s programming. For
example, if someone opens a window that is armed, the alarm
system will trigger the alarm and can alert your Security Company.
4.1 EXIT DELAY TIMER
When you arm the system, it will start the Exit Delay Timer to
provide you with enough time to exit the protected area before
the system is armed. The Status Light will flash green while the
time elapses.
The timer can be assigned different time limits and the keypad
can be programmed to display the time remaining and/or beep
while the time elapses on the timer. Discuss these options with
your installer.
4.2 REGULAR ARMING
This method is used for the everyday arming of the system. All
zones within the protected area must be closed to arm the
system. To check the status of the zones in each area, refer to
section 3.6 Area Status Display.
Digiplex LCD Keypad’s 13
How do I Regular Arm the system?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
If you have access to more than one area, press the area’s
number, press the
button for all areas, or use the
and
buttons and press
when the area you
want to arm appears.
After the Confirmation Beep, “Regular Arming” should appear
on the LCD screen and the exit delay timer will begin the
countdown to arming.
If enabled by the installer, the One-Touch Buttons
(section 4.6) or a keyswitch (section 4.7) can also be
used to arm the area.
4.3 STAY ARMING
Stay Arming will partially arm your system to permit you to remain in
the protected area. Based on your instructions, your installer will
program specific zones as Stay Zones. These zones will not arm
when you Stay Arm. For example, you can arm your doors and
windows at home without arming the motion detectors so you will be
protected while you sleep. Only User Access Codes with the Stay
and Instant Arm option enabled can Stay Arm the system. Also, see
section 4.8 Auto-Arming for another everyday arming option.
14 User’s Manual
4.3.1 Stay Arming with Delay
Stay Arming with Delay functions like Stay Arming except the
installer can program armed zones with an Entry Delay Timer. If
these zones are accidently triggered, the timer will start to allow you
time to disarm the area(s).
How do I Stay Arm?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press
button.
If you have access to more than one area, press the area’s
number, press the
button for all areas, or use the
and
buttons and press
when the area you
want to Stay Arm appears.
After the Confirmation Beep, “Stay Arming” should appear on
the LCD screen and the exit delay timer will begin.
If enabled by the installer, the One-Touch Buttons (section 4.6)
or a keyswitch (section 4.7) can be used to arm the area.
4.4 INSTANT ARMING
This feature is similar to Stay Arming. Instant Arming will partially arm
your system to permit you to remain in the protected area, but all
zones, including the entry/exit point, are changed to instant alarm
zones. Therefore, if any armed zone is breached, the alarm will
instantly be triggered. Only User Access Codes with the Stay and
Instant Arm option enabled will be able to Instant Arm.
Digiplex LCD Keypad’s 15
4.4.1 Instant Arming with Delay
Instant Arming with Delay functions like Instant Arming except
the installer can program certain armed zones within the
protected area(s) with an Entry Delay Timer. If these zones are
accidently triggered, the timer will start to allow you enough time
to disarm the area(s).
How do I Instant Arm?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
If you have access to more than one area, press the area’s
number, press the
button for all areas, or use the
and
buttons and press
when the area you want
to Instant arm appears.
After the Confirmation Beep, “Instant Arming” will appear
briefly on LCD screen and the exit delay timer will begin.
If enabled by the installer, the One-Touch Buttons
(section 4.6) or a keyswitch (section 4.7) can also be
used to arm the area.
4.5 FORCE ARMING
Force Arming allows you to arm your system when specific
zones are open. Certain zones can be programmed by the
installer to remain unarmed when you initiate Force Arming.
Once the open zone is closed, however, the system will then arm
16 User’s Manual
it as well. Only User Access Codes with the Force Arm option
enabled can Force Arm the system. This feature is commonly
used when a motion detector is protecting an area that is
occupied by a keypad. During Force arming, the motion detector
will remain unarmed until you exit the area that it protects. The
system will then arm the motion detector.
How do I Force Arm?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
If you have access to more than one area, press the area’s
number, press the
button for all areas, or use the
and
buttons and press
when the area you
want to Force Arm appears.
After the Confirmation Beep, “Force Arming” will appear
briefly on LCD screen and the exit delay timer will begin.
If enabled by the installer, the One-Touch Buttons
(section 4.6) or a keyswitch (section 4.7) can also be
used to arm the area.
Digiplex LCD Keypad’s 17
4.6 ONE-TOUCH BUTTONS
At the touch of a button you can view the Area Status Display
(see section 3.6) for a Partitioned System (see section 3.5).
Press and hold:
Your installer can also program your system to respond to certain
features with just a touch of a button. You will then have access
to the following features without using your User Access Code by
pressing and holding the desired button.
Press and hold:
For more information on these features, please refer to their
sections.
18 User’s Manual
4.7 KEYSWITCH ARMING
Your installer can add a keyswitch to arm and disarm your
system. The keyswitch can be programmed to Regular, Stay,
Force, or Instant Arm, and Disarm a specific area. The keyswitch
will also be programmed by the installer to function as a
Maintained or Momentary keyswitch.
4.7.1 Maintained Keyswitch
To arm the system, place in the “on” position.
To disarm the system, place in the “off” position.
4.7.2 Momentary keyswitch
To arm the system, place in the “on” position briefly then place it back
in the “off” position. Repeating this process will disarm the system.
4.8 AUTO-ARMING
Your installer can program your system to allow you to arm your
system automatically if specific conditions occur.
4.8.1 Timed Auto-Arming
If enabled, you can set the time that an area will arm itself
automatically.
Digiplex LCD Keypad’s 19
How do I set the Auto-Arming timer?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
button.
3) Press the
If you have access to more than one area, press the area’s
number or use the
and
buttons and press the
button when the area you want to program appears
on screen.
4) Enter the [TIME] you want the area to be armed according to
the 24-hour clock (i.e. 9 a.m. is 09:00 and 9 p.m. is 21:00).
5) Press the
button to save and exit.
4.8.2 No Movement Auto-Arming
Your system can be programmed to send a report to the Security
Company and/or arm the system if there is no activity in the area during
a specified period of time. Speak to your installer about this feature.
4.9 BYPASS PROGRAMMING
The installer can program certain zones with the bypass option
so you can program the system to bypass certain zones when
you arm the protected area. When a zone is bypassed, it will
remain unarmed once the system is armed. This option may be
useful, for example, when renovating part of the protected area.
20 User’s Manual
Bypassed zone(s) will be kept in memory until the area is armed.
Once the area is disarmed, the system will unbypass the zones.
To bypass a zone:
• The zone must have the Bypass option programmed by the
installer.
• Your User Access Code must be programmed to enable the
Bypass option.
• Your User Access Code must have access to the zone's Area
Assignment.
Fire Zones cannot be bypassed.
4.9.1 Zone Bypass
How do I bypass a zone?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
3) Enter the zone number or use the
and
buttons
and press
once the zone you want to bypass appears.
If “zone bypassed” does not appear on the screen and the keypad emits the Rejection Beep, the zone may not have the
bypass feature enabled.
4) Press the
button to exit.
Digiplex LCD Keypad’s 21
4.9.2 Bypass Recall
Bypass Recall reinstates all the zones that were bypassed the last
time the system was armed.
How do I activate Bypass Recall?
1) Enter your [ACCESS CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
button.
3) Press the
Zones bypassed during the last time the system was armed are
bypassed.
4) Press the
button to exit.
If you have a Partitioned System, only the zones in the
area(s) assigned to your User Access Code will be
affected.
Use the
and
buttons if you want to verify which zones
were bypassed the last time the system was armed after you
press the
button (Step 3). “Bypassed” or “Zone Normal” will
appear below the zones. If you want to unbypass a zone or vice
versa, press the
button.
22 User’s Manual
5.0 DISARMING
When the system is disarmed, the alarm system deactivates the
zones so the alarm will not be triggered if zones are breached.
Any user can disarm the system unless their code has been
assigned the Arm Only option.
5.1 ENTRY DELAY TIMER
Your installer will program designated entry points (i.e. the front
door) with an entry delay. This delay will allow you enough time to
enter your code to disarm the system before the alarm is triggered.
5.2 DISARMING AN ARMED SYSTEM
You can only disarm the area to which your User Access Code is
assigned. User Access Codes with the Arm Only option cannot
disarm area(s).
Digiplex LCD Keypad’s 23
How do I disarm the system?
If you are disarming a Stay or Instant Armed area, go to step 2.
1) Enter through a designated entry.
The keypad will beep and begin the Entry Delay Timer.
2) Enter your [ACCESS CODE].
3) Press the
button.
If you have access to more than one area, press the area’s
number, press the
button for all areas, or scroll and
press
when the area you want to disarm appears.
After Confirmation Beep, “Success Disarm” should appear on
LCD screen.
If enabled by the installer, a One-Touch Button (section
4.6) or a keyswitch (section 4.7) can also be used to
disarm the area.
How do I disarm an accidentally triggered system?
1) Enter your [ACCESS CODE].
2) Call your Security Company quickly to advise them of the false
alarm.
24 User’s Manual
5.3 ALARM MEMORY DISPLAY
Your system will record all the alarms that occurred during the last
armed period. If an alarm was triggered, the keypad will display
“Alarms in Memory”.
In case of a burglar alarm, leave the premises and
call your Security Company from a safe place.
How do I view the list of the alarms that occurred?
When an alarm has occurred, the LCD screen will display
“Alarms in Memory [MEM] to View”.
1) Press the
button.
Each zone whose alarm was triggered will appear below “Alarm in:”.
2) Press the
button to exit the Alarm Memory Display.
The zones in alarm will remain in the Alarm Memory until
the next time that area is armed.
Digiplex LCD Keypad’s 25
6.0 ACCESS CODES
Access Codes allow access the system. These codes can be
programmed to permit access to all or some features and areas.
The installer will program User Access Codes to be four digits, six
digits, or variable from one to six digits in length. Each digit can be
any value between zero and nine. If the installer programmed your
system to accept a variable code length, you may have to press the
button after entering their User Access Code. Only the System
Master Code cannot be less than 4 digits.
6.1 KEYPAD LOCK-OUT
If a consecutive number of invalid codes are entered on the
keypad, the installer can program the system to lock-out access
from the keypad for a specified period of time.
6.2 ERASING ACCESS CODES
To delete existing Access Codes, follow the directions in Figure
5-2 on page 29, but press the
button in Steps 5, 6, and 7.
Once the information is erased, press the
button to save
and exit.
26 User’s Manual
6.3 SYSTEM MASTER CODE (Default 123456)
The System Master Code will give you access to all the features
available on your system as well as the ability to add, modify, or
delete any User Access Codes. We suggest that you change this
code to prevent others from accessing and changing your
options without authorization.
How do I change the System Master Code?
1) Enter the current [SYSTEM MASTER CODE].
After Confirmation Beep, “Access Granted” should appear.
2) Press the
button.
3) Press the
button.
“User code [ ] Enter a number” should appear on LCD screen.
4) Enter the numbers [0] and [1].
5) Enter a [NEW
6) Press the
CODE].
button to exit.
6.4 USER ACCESS CODES
Your system supports up to 63 User Access Codes. Codes are given
a User Number between 02 and 64 (User Number 01 is the System
Master Code).User Access Codes can be programmed with various
options that will allow you to control the access to your system. The
System Master Code and codes with the Master feature can program
User Access Codes with their User Options and Area Assignment.
Digiplex LCD Keypad’s 27
If the keypad emits a Rejection Beep once you have
completed all the steps, you may have chosen an existing
User Code or the Master code used to modify or create the
code does not have access to the User Options or Area
Assignment programmed.
You grant users access to the features or areas by turning ON or
OFF the number corresponding to the option or area. The option is
considered ON when the number appears within the brackets. You
turn options ON and OFF by pressing the number buttons on the
keypad (see example Figure 5-1).
Figure 5-1: Example of Activating Options
28 User’s Manual
Figure 5-2: Programming User Access Codes
Digiplex LCD Keypad’s 29
Table 1: User Options
Options on the User Access Codes that activate access to
features.
Press option on/off Option Description
off
off
on
off
on
on
off
on
off
on
30 User’s Manual
Master feature disabled.
Master feature enabled.
Modifies User Code only.
Full Master feature enabled.
Create or modify other User Codes, User
Options, and Area Assignment according
to its own User Options and Area
Assignment.
Duress feature disabled.
Duress feature enabled.
Can arm, disarm, and send a silent alarm
to the Security Company. For use when
someone forces you to arm or disarm
areas.
Bypass feature disabled.
Bypass feature enabled.
Can deactivate zones using the Bypass
feature
Press option on/off Option Description
off
on
off
on
off
on
off
on
Arm Only feature disabled.
Arm Only feature enabled.
Can arm assigned areas, but CANNOT
disarm.
Stay & Instant Arm feature disabled.
Stay & Instant Arm feature enabled.
Can Stay or Instant Arm the system
Force Arm feature disabled.
Force Arm feature enabled.
Can Force Arm the system.
User Access Code obeys the keypad's
area assignment in a Partitioned System.
When you enter your User Access Code,
the keypad will permit access only to areas
it controls.
Keypad obeys the User Access
Code's area assignment.
The keypad will permit access to all the
areas assigned to the User Access Code
regardless which areas the keypad
controls.
Digiplex LCD Keypad’s 31
Table 2: Area Assignment
In a Partitioned System the system can be divided into four
distinct protected areas. Programming access to a specific area
or areas is called Area Assignment. User Access Codes are only
able to perform actions (arming, disarming, etc.) in the area(s)
the code is assigned.
Press button on/off Area Assignment
on
on
on
on
All four buttons off
Access to Area 1
Access to Area 2
Access to Area 3
Access to Area 4
Controls PGMs only (if PGMs are
programmed by the installer).
When the area's number is OFF, the User Access Code
does not have access to that protected area.
32 User’s Manual
7.0 TROUBLE DISPLAY
If your system is tampered with or experiences problems, the
Trouble Display will appear on the LCD screen. Most of the trouble
conditions can be programmed by your installer to be reported
directly to your Security Company. A keypad will only display
troubles that occur in the area(s) to which it has been assigned.
Potential troubles have been sorted into eight groups. The
messages that the LCD screen will display after experiencing the
trouble are listed below with a brief explanation of the cause.
We strongly suggest that you inform your Security
Company of the trouble and allow them to service your
system.
How do I view the Trouble Display?
1) When in Normal Mode (see section 3.3.1) and “Trouble(s)
[TRBL] to View” appears on the LCD screen.
2) Press the
button.
The Group heading will appear with the particular trouble
causing the problem. The Troubles by Group are listed below.
3) Use the
and
buttons to view the specific trouble.
If your keypad is in Confidential Mode (see section 3.3.2), “Troubles
[TRBL] to View” will not appear on the LCD screen until you enter
your User Access Code or press a button, depending on how your
keypad was programmed.
Digiplex LCD Keypad’s 33
7.0.1 Group 1: System
AC Failure
The control panel has detected a power failure. This means that your
system is running on the back-up battery. This trouble can be
programmed not to appear on the LCD screen when it occurs. The
AC Light on your keypad will be turned off during a power failure. If
this trouble occurs when your establishment is not experiencing a
power failure, call your Security Company for repairs.
Battery Trouble
The back-up battery is disconnected, needs to be recharged, or
replaced.
AUX Current Limit
Devices connected to the control panel have exceeded current limits.
The Auxiliary Output will shutdown until the trouble has been
rectified.
Bell Current Limit
The bell or siren connected to the control panel has exceeded
current limits. The Bell/Siren Output will be shutdown until the trouble
is rectified.
Bell Absent
The control panel has detected that the bell or siren is not connected.
ROM check Error
The control panel registers a memory error.
34 User’s Manual
7.0.2 Group 2: Communicator
TLM (Telephone Line Monitor)
The control panel is unable to access the telephone line.
Fail to Communicate 1
Fail to Communicate 2
Fail to Communicate 3
Fail to Communicate 4
The control panel has tried all assigned telephone numbers and has
failed to communicate with the Security Company.
Fail to Communicate PC
The control panel is unable to communicate with the Security
Company's diagnostic software.
7.0.3 Group 3: Modules Trouble
Module Tamper
The control panel registers that someone has triggered the tamper
switch on a module.
ROM Check Error
The control panel registers a memory error in a module.
TLM Trouble
A module is unable to access the telephone line.
Fail to Communicate
A module has failed to communicate with the Security Company.
Printer Trouble
The control panel registers a problem with the printer. Check printer
for problems (paper jam, no paper, no power, etc.) before calling
installer.
Digiplex LCD Keypad’s 35
AC Failure
Module power failure.
Battery Failure
Module's battery is disconnected, needs to be recharged, or
replaced.
Supply Output
Module has exceeded current limits.
7.0.4 Group 4: Bus Troubles
Missing Keypad
A keypad is no longer communicating with the control panel.
Missing Module
A device no longer communicating with the control panel.
General Failure
No communication between devices and the control panel.
Bus Overload
Too many devices are connected on the Bus.
Bus Communication Error
The Bus is having difficulty communicating with the devices and the
control panel.
7.0.5 Group 5: Zone Tamper
The zone or zones that were tampered with will be displayed on the LCD
screen.
36 User’s Manual
7.0.6 Group 6: Zone Low Battery
If a wireless device's battery needs to be replaced, the zone that it is
assigned to will be displayed on the LCD screen. Also, the light on
the device will flash to indicate this trouble.
7.0.7 Group 7: Zone Fault
A wireless device is no longer communicating with its receiver or a
Fire Loop connection trouble is occurring.
7.0.8 Group 8: Clock Loss
The time and date have been reset to the default. This is the only
trouble that we recommend that you correct. “Clock Loss [8] to
Set” will appear on the LCD screen after you press the
button.
To correct the date and time from Normal Mode, enter your
[ACCESS CODE], press the
button, then follow the
instructions below.
How do I reset the time and date?
1) Press the
button.
2) To change the time, place the underline under the desired
number by using the
button and enter the hour and
minutes according to the 24-hour clock (i.e. 9pm is 21:00).
3) To change the date, place the underline under the desired number and enter the correct date according to year/month/day.
4) Press the
button to exit.
Digiplex LCD Keypad’s 37
7.1 EVENT RECORD DISPLAY
The Event Record Display will record the user-initiated actions
that occurred in your system as well as any alarms or troubles.
For example, when a valid code is entered, the User Access
Code and the action taken (arm, disarm, etc.) is recorded.
You have the choice of viewing the events in all the areas assigned
to your User Access Code or by individual area. In either case the
most recent event is displayed first (see Figure 6-1).
You will only be able to view the events that occurred in
the areas assigned to your User Access Code.
How do I view the Event Record?
1) Enter your [ACCESS CODE].
2) Press the
button.
3) To view events:
Press the
button for all areas
Press the
button for only the First Area
Press the
button for only the Second Area
Press the
button for only the Third Area
Press the
button for only the Fourth Area
4) Use the
button to view subsequent events.
5) Press the
38 User’s Manual
button to exit.
Once you have entered the Event Record Display, you can
change the order that the Event Record screens (see Figure 6-1)
appear by pressing the
button. If you already know the
number of the event you want to view, press the
button and
then enter the event's number.
Figure 6-1: Event Record screens
Messages like “First Area” and “Code 01” shown in Figure 6-1 are
pre-programmed messages that your installer may have
customized to suit your system. For example, “First Area” could be
replaced by “Warehouse”. The Number of the Event may cut off
the last few letters of these custom messages. For example,
“Warehouse” may appear as “Wareh001”.
Digiplex LCD Keypad’s 39
8.0 ADDITIONAL FEATURES
8.1 PROGRAMMABLE OUTPUTS (PGMS)
Your Digiplex system includes five programmable outputs
(PGMs) that can be programmed by your installer. A PGM
triggers when a predetermined event or series of events occurs
in your system. The PGMs can be programmed to reset smoke
alarms, turn on light switches, open or close garage doors and
much more. Ask your installer about this useful feature.
8.2 KEYPAD SETTINGS
You can modify the keypad settings to suit your needs (see
Figure 7-1).
1) Scrolling Speed is how long the messages stay on the screen
before moving to the next message.
2) Backlight refers to the illumination behind the buttons and LCD
screen.
3) Contrast refers to how dark or pale characters on the screen
will appear.
40 User’s Manual
Figure 7-1: Modifying LCD screen settings
Digiplex LCD Keypad’s 41
8.3 SET TIME & DATE
If the wrong time and /or date are displayed on the Normal Mode
screen, you can reset them.
How do I reset the time and date?
1) Press the
button
2) Press the
button.
3) To change the time, place the underline under the number you
want to change by using the
button and enter the hour
and minutes according to a 24-hour clock (i.e. 9 a.m. is 09:00
and 9 p.m. is 21:00).
4) To change the date, place the underline under the number
you want to change and enter the correct date according to
year/month/day.
5) Press the
button to exit.
8.4 PROGRAMMING CHIME ZONES
You can program the keypads to emit a rapid, intermittent beep
whenever designated zones are opened or only when opened
between certain hours. These zones are referred to as Chime
Zones. Your installer can program your Chimed zones to also
beep upon closure.
42 User’s Manual
Figure 7-2: Programming Chime Zones
Digiplex LCD Keypad’s 43
8.5 PANIC ALARMS
Your system can be programmed to send an alarm to your
Security Company to request help from the police, a medical
facility, the fire department, or anyone you wish when you press
a pre-determined combination of buttons. Ask your installer
about programming these features in your system.
Emergency Panic
Press & hold the
and
buttons simultaneously for two
seconds to generate an alarm. The alarm can be programmed by the
installer to be either silent or audible according to your preference.
Auxiliary Panic
Press & hold the
and
buttons simultaneously for two
seconds to generate an alarm. The alarm can be programmed by the
installer to be either silent or audible according to your preference.
Fire Panic
Press & hold the
and
buttons simultaneously for two
seconds to generate an alarm. The alarm can be programmed by the
installer to be either silent or audible according to your preference.
44 User’s Manual
8.6 QUICK FUNCTION BUTTONS
You will only need to use the Quick Function Buttons upon your
installer or Security Company's request. Only the System Master
Code or User Access Codes with the Master feature enabled will
be able to access these functions.
How do I access the Quick Function Buttons?
1) Enter your [ACCESS CODE]
2) Press the
button.
3) Press one of the following for the system to:
button: send a test report to the Security Company
button: call the Security Company's diagnostic software.
button: answer the Security Company's diagnostic software.
button: cancel the communication with Security Company.
Digiplex LCD Keypad’s 45
9.0 FIRE AND BURGLAR ALARMS
9.1 STANDARD FIRE ZONE
During a fire alarm, the bell/siren emits an intermittent sound
(BEEP-BEEP-BEEP) until silenced or reset. If the zone is a Standard
Fire Zone, the system can immediately send an alert to your
Security Company.
How do I disarm a false alarm?
1) Enter your [ACCESS CODE] on the keypad.
2) Call your Security Company quickly to advise them of the
false alarm.
The Fire Zone may reset itself once the problem has
cleared. If it does not, simultaneously press and hold
the
and
buttons for two seconds.
9.2 DELAYED FIRE ZONE
During a fire alarm, the bell/siren will emit an intermittent sound
(BEEP-BEEP-BEEP) until silenced or reset. If the zone is a Delayed
Fire Zone, there is an automatic delay before the system
contacts the Security Company (see Figure 8-1). This will
prevent unnecessary reporting of false alarms.
If you are unable to cancel the fire alarm, the system will
send an alert. Call your Security Company to advise them
of the false alarm.
46 User’s Manual
What do I do if the fire alarm is accidentally triggered?
1) Press the
button within 30 seconds of the alarm.
2) Clear the problem from the area.
3) If problem remains after 90 seconds, the alarm will sound
again. Press
again.
The system will delay reporting the alert for another 30 seconds.
The Fire Zone may reset itself once the smoke has
cleared. If it does not, simultaneously press and hold
the
and
buttons for two seconds or speak
to your installer.
Digiplex LCD Keypad’s 47
Figure 8-1: Delayed Fire Zone
48 User’s Manual
9.3 FIRE SAFETY TIPS
How should you prepare in case of a fire in your home or business?
1) Remind everyone to escape first, then call for help.
2) Develop a fire escape plan and designate a meeting place outside.
3) Practice the escape plan frequently.
4) Plan two ways to escape from every room, if possible.
5) Practice feeling the way out with eyes closed.
6) Tell everyone never to stand up during a fire, always crawl under
the smoke and keep mouths covered.
7) Instruct everyone never to return to a burning building for any
reason; it may cost them their life.
8) Check smoke alarms regularly; working smoke alarms dramatically
increase everyone's chances of surviving a fire.
9.4 MINIMIZING HOME FIRE HAZARDS
How can you avoid the three most common causes of fires at home?
1) Never leave cooking food unattended. It's also the leading cause
of fire injuries. Cooking fires often result from unattended
cooking and human error, rather than mechanical failure.
2) Stay alert when smoking. Careless smoking is the leading cause of fire
deaths. Smoke detectors and smolder-resistant bedding and
upholstered furniture are significant fire deterrents.
3) Maintain your heating system. Heating is the second leading
cause of residential fires. However, heating fires are a larger
problem in single family homes than in apartments. Unlike
apartments, the heating systems in single family homes are
often not professionally maintained.
Digiplex LCD Keypad’s 49
9.5 HOME FIRE WARNING SYSTEM
Household fires are especially dangerous at night. Fires produce
smoke and deadly gases that can overcome occupants while they
sleep. To warn against fire, smoke detectors should be installed
outside each separate sleeping area in the immediate vicinity of
the bedrooms and on each additional story of the family living unit,
including basements.
9.6 BURGLAR ALARM
If your armed system is breached, the burglar alarm devices
specific to your system will be triggered. If your keypad is in
Normal Mode:
• The Status Light may flash red
• “In Alarm” will appear on LCD screen.
• Bell or siren may be activated
In case of a burglar alarm, leave the premises and
call your Security Company from a safe place.
50 User’s Manual
10.0 TESTING AND MAINTENANCE
10.1 BURGLAR ALARM TESTING
Two people are needed to complete this test. One person will watch
the LCD screen on the keypad while the other person walks around
the protected area and open the zones (i.e. open the doors and
window that are protected, walk in the path of the motion detectors,
etc.). The LCD screen will display the opened zones. If a zone does
not register, contact your installer. Your installer will provide details
on the best way to test your system.
10.2 FIRE ALARM TESTING
Do NOT use an open flame or burning materials to test your fire
detection devices. Your installer will provide details on the best way
to test your system.
10.3 SYSTEM MAINTENANCE
Under normal use your system requires no maintenance other than
regular testing. We recommend that your installer change the battery
every three years.
Digiplex LCD Keypad’s 51
10.4 SYSTEM TEST
Speak to your installer before conducting a system test since the
system must be programmed to respond to the test instructions.
It is normally recommended that you conduct the system test
once a week, but contact your installer for instructions
concerning your particular system.
How do I conduct the system test?
1) Call Security Company to advise them that you are testing
the system.
2) Enter your [ACCESS CODE].
3) Press the
button.
The system will test all its connections and can send a report to
your Security Company. If the system detects a problem, the
Trouble Display will show on the LCD screen (see section 7.0).
Call your installer for repairs.
52 User’s Manual
11.0 SYSTEM CHECKLIST
Important: Keep this information in a secure location.
11.1 ZONE DESCRIPTION
Is this a Partitioned System?
Yes N
No N
Area 1 = __________________________________________
Area 2 = __________________________________________
Area 3 = __________________________________________
Area 4 = __________________________________________
Place a
(if any).
> indicate the options and area(s) enabled for that zone
Zone # and
Description
1
Area
Entry
Byp Stay Force 24Hr.
2 3 4
Delay
01:___________ N N N N N
02:___________ N N N N N
03:___________ N N N N N
04:___________ N N N N N
05:___________ N N N N N
06:___________ N N N N N
07:___________ N N N N N
08:___________ N N N N N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
____
____
____
____
____
____
____
____
Digiplex LCD Keypad’s 53
Zone # and
Description
1
Area
Entry
Byp Stay Force 24Hr.
2 3 4
Delay
09:___________ N N N N N
N
N
N
11:___________ N N N N N
N
N
N
10:___________ N N N N N
12:___________ N N N N N
13:___________ N N N N N
14:___________ N N N N N
15:___________ N N N N N
16:___________ N N N N N
17:___________ N N N N N
18:___________ N N N N N
19:___________ N N N N N
20:___________ N N N N N
21:___________ N N N N N
22:___________ N N N N N
23:___________ N N N N N
24:___________ N N N N N
25:___________ N N N N N
26:___________ N N N N N
27:___________ N N N N N
28:___________ N N N N N
54 User’s Manual
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
Zone # and
Description
1
Area
Entry
Byp Stay Force 24Hr.
2 3 4
Delay
29:___________ N N N N N
N
N
N
31:___________ N N N N N
N
N
N
30:___________ N N N N N
32:___________ N N N N N
33:___________ N N N N N
34:___________ N N N N N
35:___________ N N N N N
36:___________ N N N N N
37:___________ N N N N N
38:___________ N N N N N
39:___________ N N N N N
40:___________ N N N N N
41:___________ N N N N N
42:___________ N N N N N
43:___________ N N N N N
44:___________ N N N N N
45:___________ N N N N N
46:___________ N N N N N
47:___________ N N N N N
48:___________ N N N N N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
Digiplex LCD Keypad’s 55
Exit Delay:
Area 1 is ___________ seconds.
Area 2 is ___________ seconds.
Area 3 is ___________ seconds.
Area 4 is ___________ seconds.
The entry delays appear in the Zone Description table.
11.2 ACCESS CODES
For security reasons, write only the user’s name and not his or
in the squares to identify which
her access code. Place a
options are enabled.
>
4-Digit Codes N 6-Digit Codes N
User #, Name
1 to 6 Digit Codes N
Keypad
Area
Full
Arm
Master
Byp Stay Force
Duress obeys
1234
Master
Only
code
System Master 1 2 3 4
Code
02:_______
___
03:_______
___
04:_______
___
05:_______
___
06:_______
___
07:_______
___
08:_______
___
56 User’s Manual
N
N
N
N
N
N
N
> > > >
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
>
N
N
N
N
N
N
N
User #, Name
09:_______
Keypad
Area
Full
Arm
Master
Byp Stay Force
Duress obeys
1234
Master
Only
code
___
10:_______
___
11:_______
___
12:_______
___
13:_______
___
14:_______
___
15:_______
___
16:_______
___
17:_______
___
18:_______
___
19:_______
___
20:_______
___
21:_______
___
22:_______
___
23:_______
___
24:_______
___
25:_______
___
26:_______
___
27:_______
___
28:_______
___
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Digiplex LCD Keypad’s 57
User #, Name
Keypad
Area
Full
Arm
Master
Byp Stay Force
Duress obeys
1234
Master
Only
code
29:_______
___
30:_______
___
31:_______
___
32:_______
___
33:_______
___
34:_______
___
35:_______
___
36:_______
___
37:_______
___
38:_______
___
39:_______
___
40:_______
___
41:_______
___
42:_______
___
43:_______
___
44:_______
___
45:_______
___
46:_______
___
47:_______
___
48:_______
___
58 User’s Manual
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
User #, Name
Keypad
Area
Full
Arm
Master
Byp Stay Force
Duress obeys
1234
Master
Only
code
49:_______
___
50:_______
___
51:_______
___
52:_______
___
53:_______
___
54:_______
___
55:_______
___
56:_______
___
57:_______
___
58:_______
___
59:_______
___
60:_______
___
61:_______
___
62:_______
___
63:_______
___
64:_______
___
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Digiplex LCD Keypad’s 59
11.3 SPECIAL BUTTONS AND FEATURES
One-Touch Buttons:
Place a
>if the One-Touch Button is activated.
N
Stay Arm
N
Bypass Programming
N
Force Arm
N
Instant Arm
N
Regular Arm
N
Keypad Settings
N
Disarm Stay/Instant Arm N
Event Record Display
Panic Alarms:
Place a
>if the Panic Button is activated and if alarm is
silent or audible.
&
N
&
Auxiliary or ______________ NSilent NAudible
N
&
Fire or __________________ NSilent NAudible
60 User’s Manual
Emergency or ____________ NSilent NAudible
N
PGMs:
PGM
When this occurs:
This is activated:
1
__________________ __________________
2
__________________ __________________
3
__________________ __________________
4
__________________ __________________
5
__________________ __________________
11.4 OTHER INFORMATION
Installed By:___________________ Date:_________________
Service provided by:_________________Tel:______________
Monitoring Station:_________________Tel:________________
Your account number is: ______________________________
Alarm transformer location:__________ on circuit #:__________
Location of Telephone Connections:______________________
Digiplex LCD Keypad’s 61
Warranty
The Seller warrants its products to be free from defects in
materials and workmanship under normal use for a period of
one year. Except as specifically stated herein, all express or
implied warranties whatsoever, statutory or otherwise,
including without limitation, any implied warranty of
merchantability and fitness for a particular purpose, are
expressly excluded. Because Seller does not install or connect
the products and because the products may be used in
conjunction with products not manufactured by Seller, Seller
cannot guarantee the performance of the security system.
Seller obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller's option, any product
not meeting the specifications. In no event shall the Seller be
liable to the buyer or any other person for any loss or damages
whether direct or indirect or consequential or incidental,
including without limitation, any damages for lost profits, stolen
goods, or claims by any other party caused by defective goods
or otherwise arising from the improper, incorrect or otherwise
faulty installation or use of the merchandise sold.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement