AOC 193FW - MANUEL 2 Operating instructions


Add to my manuals
21 Pages

advertisement

AOC 193FW - MANUEL 2 Operating instructions | Manualzz

193FW+

TABLE OF CONTENTS

FOR YOUR SAFETY -------------------------------------------------- 1

SAFETY PRECAUTIONS -------------------------------------- 2

SPECIAL NOTES ON LCD MONITORS ------------------- 3

BEFORE YOU OPERATE THE MONITOR --------------------- 3

FEATURES -------------------------------------------------------- 3

PACKING LIST --------------------------------------------------- 3

INSTALLATION INSTRUCTIONS --------------------------- 4

CONTROLS AND CONNECTORS -------------------------- 5

ADJUSTING THE VIEWING ANGLE ----------------------- 6

OPERATING INSTRUCTIONS ------------------------------------- 7

GENERAL INSTRUCTIONS ---------------------------------- 7

HOW TO ADJUST A SETTING ------------------------------ 9

ADJUSTING THE PICTURE ----------------------------- 10-11

PLUG AND PLAY ----------------------------------------------- 12

TECHNICAL SUPPORT(FAQ) -----------------------------------13

ERROR MESSAGE & POSSIBLE SOLUTION -------- 14

HOW TO INSTALL INF & ICM FILE -------------------------15

APPENDIX -------------------------------------------------------------- 16

SPECIFICATIONS -----------------------------------------16-17

FACTORY PRESET TIMING TABLE ---------------------18

CONNECTOR PIN ASSIGNMENT ------------------------19

Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference.

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference.

As an E NERGY S TAR

®

Partner our company has determined that this product meets the E NERGY S TAR

®

guidelines for energy efficiency.

WARNING:

To prevent fire or shock hazard, do not expose the monitor to rain or moisture.

Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

1

PRECAUTIONS

z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.

Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. z Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. z The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. z The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. z Unplug the unit during a lightening storm or when it will not be used for long period of time. This will protect the monitor from damage due to power surges. z Do not overload power strips and extension cords. Overloading can result in fire or electric shock. z Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. z Do not attempt to service the monitor by yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. z

To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A. z The wall socket shall be installed near the equipment and shall be easily accessible. z

For use only with the attached power adapter (Output 12Vdc) which have

UL, CSA listed license.

2

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a problem.

NOTES

Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.

You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.

Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image when the same image has been displayed for a long time. The monitor will slowly recover from this.

BEFORE YOU OPERATE THE MONITOR

FEATURES

19” (48cm) Wide screen TFT Color LCD Monitor

Crisp, Clear Display for Windows

Recommened Resolutions: 1440 X 900@60Hz

E NERGY S TAR

® •

EPA

Dual Input (DVI + Analog)

Ergonomic

Space Saving, Compact Case Design

CHECKING THE CONTENTS OF THE PACKAGE

The product package should include the following items:

3. Power Cord

7. Driver-Disk

3

INSTALLATION INSTRUCTIONS

SWIVEL BASE

Install Remove

Figure 1 Installing and Removing the Swivel Base

POWER CORD

Power Source:

1. Make sure that the power cord is the correct type required in your area.

2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.)

3. Connect the AC-power cord into your LCD monitor’s External Adapter input socket, and then plug the other end of External adapter to LCD monitor’s DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.

NOTES

A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0.75mm

2

or

H05VVH2-F2 3G 0.75mm

2

) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G

0.75mm

2

) shall be used.

4

CONTROLS AND CONNECTORS

VIDEO CABLE

Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer’s D-Sub port.

Connecting the Power Cord: Plug the AC-power cord into the External

Adapter. Then plug the DC-jack power cable into DC-IN Inlet.

Connecting the DVI Cable: Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer’s DVI port.

Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).

Figure 2 Connecting Cables

1. DC-Jack Power Cable

3. AC Power Cord

5

ADJUSTING THE VIEWING ANGLE

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference.

Hold the stand so you do not topple the monitor when you change the monitor’s angle.

You are able to adjust the monitor’s angle from -5

°

to 20

°

.

Figure 3

NOTES

Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.

Careful attention is required not to catch your fingers or hands when you change the angle.

6

OPERATING INSTRUCTIONS

GENERAL INSTRUCTIONS

Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.

The power cord should be connected.

Connect the video cable from the monitor to the video card.

Press the power button to turn on the monitor position. The power indicator will light up.

Figure 4 External Control Button

EXTERNAL CONTROLS

1. Power Key

3. MENU/ENTER

2. LED

4. Luminance

5. Brightness Preset 6. Auto Adjust Key/Exit

7

FRONT PANEL CONTROL

Power Button:

Press this button to switch ON/OFF of monitor’s power.

MENU / ENTER :

Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast

Adjust OSD status.

Luminance :

Adjust contrast and brightness or function adjust.

*Only adjustable at “STD” mode

(see Brightness Preset below)

Brightness Preset:

Switch between “STD”, “OFFICE” & “VIVID”.

Auto Adjust button / Exit:

1. When OSD menu is in active status, this button will act as EXIT-KEY

(EXIT OSD menu).

2. When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function.

The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.

Power Indicator:

Green — Power On mode.

OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.

NOTES

Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.

Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor.

For maximum protection, repackage your monitor as it was originally packed at the factory.

To keep the monitor looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.

8

HOW TO ADJUST A SETTING

1. Press the MENU-button to activate the OSD window.

2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.

3. Press or to change the settings of the selected function.

4. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-3.

Figure 5 The OSD Message

9

ADJUSTING THE PICTURE

The descriptions for function control LEDS

Main

Menu Item

Main

Menu

Icon

Sub Menu

Item

Sub

Menu

Icon

Contrast

Description

Contrast from Digital-register.

Luminance

Image

Setup

Image

Position

Color

Temp.

Input

Select

Brightness

Backlight Adjustment

Focus

Clock

H. Position

V. Position

Adjust Picture Phase to reduce

Horizontal-Line noise

Adjust picture Clock to reduce

Vertical-Line noise.

Adjust the horizontal position of the picture.

Adjust the verticalposition of the picture.

Warm N/A from EEPROM.

Recall Cool Color Temperature from

Cool N/A

EEPROM.

Recall sRGB Temperature from sRGB N/A

EEPROM.

User / Red Red Gain from Digital-register.

User /

Green

Green Gain Digital-register.

User / Blue Blue Gain from Digital-register.

Select input signal from analog

Analog N/A source (D-Sub)

10

Main

Menu Item

Main

Menu

Icon

Sub Menu

Item

Sub

Menu

Icon

OSD Setup

Language

Information

Reset

Exit

Description

H. Position

Adjust the horizontal position of the

OSD.

V. Position

Adjust the verticalposition of the

OSD.

OSD

Timeout

Adjust the OSD timeout.

Language N/A Select the language you like.

Information N/A

Show the resolution, H/V frequency and input port of current input timing.

Clear each old status of Auto-

Yes N/A configuration .

Do not execute reset, return to

No N/A main menu.

11

PLUG AND PLAY

Plug & Play DDC 2B Feature

This monitor is equipped with VESA DDC 2B capabilities according to the

VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.

The DDC 2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC 2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS

NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE

PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.

This monitor meets the Green monitor standards as set by the Video

Electronics Standards Association (VESA) and/or the United States

Environmental Protection Agency (EPA) and The Swedish Confederation

Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present.

When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.

USING THE RIGHT POWER CORD :

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.

Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type

SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.

The other end terminates with a molded-on type connector body, rated 10A,

250V, having standard CEE-22

female configuration.

Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

12

TECHNICAL SUPPORT (FAQ)

Problem & Question

Power LED is not on

No Plug & Play

Picture is fuzzy

Possible Solution

*Check if the Power Switch is in the ON position

*Power Cord should be connected

*Check if the PC system is Plug & Play compatible

*Check if the Video Card is Plug & Play compatible

*Check if the D-15 plug pin of Video

Cable is bent

*Make sure the LCD Monitor Drivers are installed

*Adjust the Contrast and Brightness

Controls.

*Move electrical devices that may cause electrical interference.

*Computer Power Switch should be in

Picture bounces or a wave pattern is present in the picture

The power LED is ON (Red) but there’s no video or no picture. the ON position.

*Computer Video Card should be snugly seated in its slot.

*Make sure monitor’s video cable is properly connected to the computer.

*Inspect monitor’s video cable and make sure none of the pins are bent.

*Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS

LOCK LED. The LED should either turn

ON or OFF after hitting the CAPS LOCK key.

Missing one of the primary colors (RED, GREEN, or

*Inspect the monitor’s video cable and make sure that none of the pins are

BLUE)

Screen image is not centered or sized properly.

Picture has color defects

(white does not look white) bent.

*Adjust pixel frequency (CLOCK) and

FOCUS or press hot-key (AUTO).

*Adjust RGB color or select color temperature. disturbances on the screen CLOCK and FOCUS or perform hot- key

(AUTO-key).

CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width.

FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture.

For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode pattern.

13

ERROR MESSAGE & POSSIBLE SOLUTION

CABLE NOT CONNECTED :

1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws.

2. Check the signal-cable’s connection pins for damage.

INPUT NOT SUPPORT :

Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table.(see page 18)

14

HOW TO INSTALL THE DRIVER-DISK (INF & ICM FILE)

FOR FIRST TIME INSTALL :

Your system may not recognize your flat-panel monitor,and as a result, you may need to complete the following steps for optimum performance of your monitor.

1. Check this LCD MONITOR is properly connected to your computer.

2. Restart the computer , when win95/98 detects the presence of a Plug and Play Monitor ,its device driver can be loaded and configured dynamically, insert LCD Monitor install disk to DISK A after the Win95/98 setup wizard is appeared. This setup wizard will lead you through the steps for configuring the system.

(Select “ NEXT “ for next steps and select driver A for LCD Monitor install file, if not select driver A ,the configuration system will automatically select the standard Plug and Play driver)

3. After the installation complete you can find the monitor complete name by following steps :

Click “ START ” , select “ SETTINGS ”, select “ CONTROL PANEL “Select

“ SYSTEM ”, select “ DEVICE MANAGEMENT “, select “ MONITOR ” icon and click twice ,you can see the description as follow :

“ AOC193FW ” if this description doesn’t exist, or the “ MONITOR ” icon doesn’t exist too,that means your installation is not successful.

Please delete the description with click the right button of mouse, and select The “remove or erase” to delete the description, if your step is successful, the “ MONITOR “ icon will disappear.

Please repeat this 2nd, 3rd steps if not success

4. After you complete above setup, please follow the steps below to operate your monitor at maximum performance :

A). Double click on the My Computer icon

B). Double click on the Control Panel icon

C). Double click on the Display icon, click on the Settings tab

D). In Desktop Area drag the slider to resolution 1280x1024, and set the Color palette for 16-bit color

E). Click on the Advanced Properties the tab , set the refresh rate to 60 Hz, click the

OK button, and click on the CLOSE button

15

APPENDIX

SPECIFICATIONS

LCD Panel

Input

Display Colors

Dot Clock

Max. Resolution

Plug & Play

EPA E NERGY S TAR

®

Input Connector

Input Video Signal

Maximum Screen Size

Power Source

Environmental

Considerations

Dimension

Weight (N. W.)

Driving system TFT Color LCD

Size 48cm(19")

Pixel pitch

Video

0.285mm( H ) × 0.285mm( V )

R,G,B Analog Interface

Digital Interface

Separate Sync. H/V TTL

H-Frequency 30kHz – 83kHz

V-Frequency 55-75Hz

135MHz

1440 × 900 @60Hz

VESA DDC 2B TM

ON Mode

OFF Mode

≤ 36W

≤ 1W

15-pin D-Sub

DVI 24pin

Analog:0.7Vp-p(standard),

75 OHM, Positive

Digital signal

Horizontal : 410mm

Vertical : 256mm

100~240VAC,47~63Hz

Operating Temp: 5° to 50°C

Storage Temp.: -20° to 60°C

Operating Humidity :

10% to 85%

440×356×215 (W ×H×D)mm

4kg Unit (net)

16

External Controls: Functions

Power Consumption ( Maximum )

Regulatory Compliance

Auto Adjust Key

Brightness Preset

Luminance

Power Button

MENU

Contrast

Brightness

Focus

Clock

H. Position

V. Position

(Warm)Color

(Cool)Color

sRGB

RGB Color temperature

Input select

OSD Setup

Language

Information

Reset

Exit

36 Watts cULus, CE, MPR II,TCO’99

17

STANDARD

Dos-mode

VGA

SVGA

XGA

SXGA

WXGA+

Preset Display Modes

RESOLUTION

HORIZONTAL

FREQUENCY

720 × 400 31.47kHz

640 × 480

640 × 480

800 × 600

800 × 600

1024 × 768

1024 × 768

1024 × 768

1280 × 1024

1280 × 1024

1440 × 900

31.47kHz

37.50kHz

37.879kHz

46.875kHz

48.363kHz

56.476kHz

60.021kHz

64.000kHz

80.000kHz

55.935kHz

VERTICAL

FREQUENCY

70.0Hz

60.0Hz

75.0Hz

60.0Hz

75.0Hz

60.0Hz

70.0Hz

75.0Hz

60.0Hz

75.0Hz

59.8Hz

18

CONNECTOR PIN ASSIGNMENT

1

6

11

5

10

15

15 - Pin Color Display Signal Cable

PIN NO. DESCRIPTION

1. Red

2. Green

3. Blue

4. Ground

5. Ground

6. R-Ground

7. G-Ground

PIN NO.

9.

DESCRIPTION

+5V

8. B-Ground

24 - Pin Color Display Signal Cable

PIN NO.

1.

2.

3.

13.

14.

15.

4.

5.

6.

7.

8.

9.

10.

11.

12.

TMDS Data 2-

TMDS Data 2+

TMDS Data 2/4

Shield

TMDS Data 4-

TMDS Data 4+

DDC Clock

DDC Data

N.C.

TMDS Data 1-

TMDS Data 1+

TMDS Data 1/3

Shield

TMDS Data 3-

16.

17.

18.

19.

20.

21.

22.

23.

24.

TMDS Data 3+

+5V Power

Ground(for+5V)

Hot Plug Detect

TMDS Data 0-

TMDS Data 0+

TMDS Data 0/5

Shield

TMDS Data 5-

TMDS Data 5+

TMDS Clock Shield

TMDS Clock +

TMDS Clock -

19

20

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 48.3 cm (19")
  • 1440 x 900 pixels
  • 8 ms 300 cd/m² 500:1
  • 36 W

Related manuals

advertisement