User manual | QUICK START GUIDE

QUICK START GUIDE
NeXtage 08 - Ref. NXT0802
Thank you for choosing Analog Way and the NeXtage 08. By following these simple steps, you will be able to
set up and use your Powerful true-seamless AV processor based on Analog Way’s new LiveCore™ platform
within minutes. Discover the NeXtage 08 capabilities and intuitive interface while commanding top-notch
presentations and unleash your creativity for a new experience in show and event management.
WHAT’S IN THE BOX
Go on our website to register your product(s)
and be notified about new firmware versions:
http://bit.ly/AW-Register
• 1 x NeXtage 08 (NXT0802)
• 1 x Power supply cord
• 1 x Ethernet cross cable (for device control)
• 1 x MCO 10 pin connector
• 1 x Web-based Remote Control Software included and hosted on the device
• 1 x Rack mount kit (the parts are stowed in the packaging foam)
• 1 x User manual (PDF version)*
• 1 x Quick start guide*
* User manual and quick start guide are also available on www.analogway.com
QUICK INSTALL AND SETUP
CAUTION!
Mounting using only the front
rack ears is sufficient for fixed
installations. Additional support,
such as the rear rack support or
slide rails, is required for mobile
applications, and recommended
for all.
Connecting with the Web RCS
The NeXtage 08 uses standard ethernet LAN
networking. To connect the Web RCS to your new
NeXtage 08, you first need to connect a computer
to the NeXtage 08 using the Ethernet cable. Then
on your computer open an internet browser which
supports Flash® player.
Into this internet browser, please enter the IP
address of the NeXtage 08 displaying on the front
panel screen.
If the connection is not starting, please see:
• Be sure the computer IP address is on the same
network and subnet as the NeXtage 08.
• Be sure that no two devices have the same IP
address (prevent IP conflicts)
• Check your network cable. You will need a
crossover ethernet cable if you are connecting
directly from the NeXtage 08 to the computer. If
a hub or switch is involved, use straight ethernet
cables.
The connection should start.
• For more information, please see the user manual
or contact your local technical support.
Often, computers are set to DHCP client (automatic
IP detection) mode. You may need to change the Once you have successfully connected, the flash
IP address configuration on your computer before app will automatically download and launch in your
you can connect. These settings are found in the browser. When the two icons in the bottom right
properties for your LAN network adaptor, and vary corner of the screen turn green, the Web RCS is
by operating system.
ready to use. If you are having trouble syncronizing,
The default IP address on the NeXtage 08 is try clearing the cache and refreshing the page
192.168.2.140 with a netmask of 255.255.255.0 (ctrl+F5 in most browsers):
Therefore, you can assign your computer a static - NXT0802: will turn green when connected
IP address of 192.168.2.100 and a netmask of - Synch OK: will turn green when the Web RCS has
255.255.255.0 and should be able to connect.
finished syncronizing.
Power supply:
Swappable power unit;
100-240 VAC; 4,8A; 50/60Hz;
225W
- 8 x 3G/HD/SD-SDI
- 8 x Universal Analog
(4 x HD15 & 4 x DVI-A)
(Dual link available on Inputs 4 and 8)
- 2 x DisplayPort
(Dual link available on Inputs 2 and 6)
Inputs #1 to #8:
- 4 x HDMI
-6
x DVI-I
On/Off
Stand-by: Push the button then
use the contextual button to
enter in stand-by mode
4.3’’ TFT color display
Menu scroll
knob
See User’s Manual for details
Devices sync.:
Used for effect sync in
multi-machine mode.
Ethernet
Plug
Frame Lock:
Analog Frame
Lock plug and
specific loop
output
Tally
CAUTION:
The user should avoid disconnecting the power source
(AC input) until the unit is in stand-by mode. Failure to
do this could result in hard drive data corruption.
Monitoring Preview output:
- 1 x Universal Analog (HD15 & DVI-A)
- 1 x DVI-I
- 2 x SD/HD/3G SDI
- 1 x RGBs/RGsB/RGB/YPrBr/YC/comp
Analog output
Program output #1 - Preview output #2:
- 2 x Universal Analog (HD15 & DVI-A)
- 2 x DVI-I (DVI Dual-Link on output #1)
- 2 x Video Optical SFP module cage
- 3G/HD/SD-SDI
Source control:
Frame logo: press before selecting the
Logo/Frame number
Freeze: freeze the input linked to the
current layer on the Program
TAKE:
Transition the preselected sources onto the
Program output with the
selected effects
Step Back:
Recall the last preset into
your Preview monitor
Screen:
#1 to #2: select a screen
Edit:
Program: edit Program
Preview: edit Preview
Layer control:
Clear: clear a layer
Aspect Image Layer: adjust
Layer properties
Source selection:
#1 to #8: access Frame #1 to #4
or Logo #5 to #8
Color: fill in a layer with a color
Preset:
Load: load a preset
Save: save a preset
Layer selection:
Native Background: not
scaled layer.
A/B: scaled layers
Control:
Exit/Menu: Home menu
or back one level
Enter: validate the menu
or command
RS232 port:
Used for Secure Power
Unit (Ref. SPU001) status
management only
4 x USB Plugs
USB Plug
Contextual
buttons
NEXTAGE 08 - REF. NXT0802 / FRONT & REAR PANELS DESCRIPTION
Solid orange:
TIP: Always try to use native resolution of your screens/
projectors to avoid additional scaling.
Output settings:
Under this menu you have access to the HDCP ON/OFF feature,
Optical SFP restart and test pattern possibilities.
Other settings are available for layers, please refer to the user
manual.
• Drag sources into layers to change the source
• Load and place all your layer with your mouse and use the take
button to send it to your program
• Resize or reposition your layer by clicking and dragging the layer.
Preconfig.: Setup assistant for adjusting all basic setups.
Outputs: Manage your outputs and have access to every settings and parameters.
Inputs: Configure your inputs connected to your NeXtage 08.
Logos: Configure Logos and Frames selections.
Library: Load your Logos and Frames into the system.
Presets: Configure your preset by loading layouts.
Confidence: Configure the Confidence monitor.
Monitoring: Configure the operator’s monitor including the resolution and choice of layout, to show input or output preview
combinations.
Blending: Configure the blending.
Control: Access all control settings.
Versions: Check the version number, board checksum...
Maintenance: Access to all Analog Way maintenance services
(update, ...).
Contextual button
Blinking green:
Once your setup is complete, click on the EDIT tab to start building
your presets.
Layer/source selected or is not currently
active on the Program output
HOME MENU
Layer/source selected or is currently active
on the Program output
Blinking red:
Output format/rate:
Under SETUP > OUTPUT, click on the selected output on the left
to have access to the setup. Then choose the format and rate.
(Rate choice is only available for Monitoring/Preview output, the
main outputs will use the rate defined under SETUP > Preconfig
> Internal rate, Framelock, etc.)
Click on SETUP > INPUT > GENERAL to have an overview of your
inputs.
Operation mode:
Choose your operation mode using the setup menu (SETUP >
Preconfig > screens) to drag and drop your unused output to
the selected mode.
• To reset a preset, please click on the preset number holding
SHIFT on your keyboard. Then into the windows below click on
the reset button
• You can load your preset at any time on Program or Preview
by clicking on the preset number (with the Save mode button
disabled), or simply drag and drop the preset into the Program
or Preview windows.
• Click on SAVE MODE then choose your preset number.
Once you build a preset, you can save it as one of the 144 preset
slots the NeXtage 08 offers.
PRESET MANAGEMENT
Click on your ACTIVE PLUG in order to choose the displayed
input.
Click on the SETUP PLUG to start settings a specific plug without
choosing it as the active displayed plug. (Not necessarily
displayed).
As each input has multiple input plugs, you must choose one
plug to display as this input. The remaining non-displayed plugs
remain active and can still be configured.
Individual input setting:
Click on the left on the individual input setup in order to define
your input
Click on AUTOSET ALL to launch the automatic detection of all
inputs.
INPUT SETUP
OUTPUT SETUP
EDIT
#1 = Source is on Preview
#2 = Function available for modification
#1 = Source is on the Program output
#2 = Freeze enable
#3 = Stand-by button
#4 = Preset Selection
Solid green:
Solid red:
BUTTON COLOR USAGE
OPERATION OVERVIEW
WEB RCS STRUCTURE
SETUP
Click on SETUP, then go to the preconfig
button. The Setup assistant is here to help
you to set up step by step your unit by
following an interactive tutorial.
EDIT
The EDIT mode is the place where you will
manage all your configurations. You will
manage your inputs, your layers in terms
of size position effect etc… your Frames
and Logos. You can save all your screen
configurations into presets
LIVE
The LIVE mode is the section where you
will start operating your show. You can play
preset one after the other on a real timeline
adding some parameters like duration or
wait for user interaction.
WARRANTY AND SERVICE
This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not
include faults resulting from user negligence, special modifications, electrical surges, abuse (drop/crush),
and/or other unusual damage. In the unlikely event of a malfunction, please contact your local Analog Way
office for service.
GOING FURTHER WITH THE NEXTAGE 08
For complete details and operations procedures, please refer to the LiveCore’s unit User’s Manual and our
website for further information: www.analogway.com
Firmware v03.00.105
07/17/2015
140165 - NXT0802-QSG

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project