Datasheet

Datasheet
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
ENDA EPC4420 PID PROFILE CONTROLLER
Thank you for choosing ENDA EPC4420 profile controller.
* 48 x 48mm sized.
* Selectable sensor type.
* Automatic calculation of PID parameters (SELF TUNE).
Enter PID parameters of the system if they are known at the beginning.
Otherwise, Self-Tune should be activated.
* Communication vai RS-485 ModBus protocol (Optional).
* Selectable SSR or relay control output.
* Selectable 0-20mA or 4-20mA analog control output.
* Relay output can be programmable as second alarm or control output.
* AL1 output or Timer output or can be used as control AL1 relay output.
* Selectable Heat/Cool control.
* Input offset feature.
* In the case of sensor failure periodical running or relay state can be
selected.
* Until the eight steps to make the profile control.
* In each step AL1 and AL2 outputs proramming.
* To continue where it left off in power failure feature.
* For the keypad security levels.
* Programming by using keypad or Modbus.
* CE marked according to European Norms.
EPC 4420
CNT/AL2
SSR
PV
AL1
R
TIMER
SET
PSET
AL1
ASET
ENDA
AL2
START
STOP
PROFILE CONTROLLER
TECHNICAL SPECIFICATIONS
Input type
Pt 100 Resistance Thermometer
Pt 100 Resistance Thermometer
J (Fe-CuNi) Thermocouple
K (NiCr-Ni) Thermocouple
T (Cu-CuNi) Thermocouple
S (Pt/0Rh-Pt) Thermocouple
R (Pt13Rh-Pt) Thermocouple
EN 60751
EN 60751
EN 60584
EN 60584
EN 60584
EN 60584
EN 60584
Temperature range
°F
°C
-200...600 °C
-328... +1112 °F
-99.9...300.0 °C
-99.9...+543.0°F
0... 600 °C
+32... +1112 °F
0...1200°C
+32... +2192 °F
0... 400°C
+32... +752 °F
0...1600°C
+32... +2912 °F
0...1600°C
+32... +2912°F
Accuracy
0,2% (of full scale)
0,2% (of full scale)
0,2% (of full scale)
0,2% (of full scale)
0,2% (of full scale)
0,2% (of full scale)
0,2% (of full scale)
1 digit
1 digit
1 digit
1 digit
1 digit
1 digit
1 digit
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature 0 ... +50°C/-25... +70°C (with no icing)
Max. Relative humidity
80% up to 31°C decreasing linearly 50% at 40°C .
According to EN 60529
Front panel : IP65
Rated pollution degree
Rear panel : IP20
Height
Max. 2000m
Do not use the device in locations subject to corrosive and flammable gases.
ELECTRICAL CHARACTERISTICS
Supply
Power consumption
Wiring
Line resistance
Data retention
EMC
Safety requirements
230V AC +10% -20%, 50/60Hz or 24V AC ±10%, 50/60Hz.
Max. 5VA
2.5mm² screw-terminal connections
For thermocouple max.100ohm, for 3 wired Pt 100 max. 20ohm
EEPROM (minimum 10 years)
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B for standard EN 61000-4-3)
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
OUTPUTS
CONT./AL2
AL1
ANL/SSR
Life expectancy for relay
Relay : 250V AC, 2A ( for resistive load), NO/NC. Selectable as Control or Alarm2 output.
Relay : 250V AC, 2A ( for resistive load), NO/NC selectable. (Alarm1 output).
Selectable logic control output. (Max. 12V, 20mA)
Mechanical 30.000.000 operation; Electrical 300.000 operation
CONTROL
Control type
Control algorithm
A/D converter
Sampling time
Proportional band
Integral time
Derivative time
Control period
Hysteresis
Output power
Single set-point and alarm control
On-Off / P, PI, PD, PID (selectable)
15 bits
500ms
Adjustable between 0% and 100%. If Pb=0%, On-Off control is selected.
Adjustable between 0.0 and 100.0 minutes
Adjustable between 0.00 and 25.00 minutes
Adjustable between 1 and 250 seconds
Adjustable between 1 and 50°C/F
The ratio of power at a set point can be adjusted between 0% and 100%
HOUSING
Housing type
Dimensions
Weight
Enclosure material
Suitable for flush-panel mounting according to DIN 43 700.
W48xH48xD87mm
Approx. 250g (after packing)
Self extinguishing plastics.
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
1/6
EPC4420-E-01-R
SET
SET
If
ASET
PSET
key is pressed while holding
ASET
PSET
Con.o.
ASET
STOP
Pb
4
AL2
START
STOP
ti
4.0
AL2
AL1
START
STOP
td
1.00
AL2
AL1
START
STOP
Ct
20
AL2
AL1
START
STOP
P.SEt.
0
AL2
AL1
START
STOP
C.HyS.
2
AL2
AL1
START
STOP
C.StA.
HEAt
AL2
AL1
START
STOP
Pr.Er.
0
AL2
AL1
START
STOP
C.oT.S.
Out1
AL2
AL1
START
STOP
C.Con.
off
ALr.2
ALr.1
AL2
AL1
key, the programming mode is enabled.
ASET
AL2
Pb
Entering from the programming mode to the run mode:
If no key is pressed within 20 seconds during programming mode, the data is stored automatically and
SET
the run mode is entered.
Alternatively, the same function occurs first pressing
key and then pressing
keys together.
ASET
PSET ASET
AL2
A1.Hy. = Hysteresis of the Alarm1
output.
Adjustable between 1 and 50°C.
A1.Hy.
2
AL1
Ti = Integral time.
START
AL1
td = Derivative time.
START
STOP
A1.tP. =
Function of Alarm1 output.
Four kinds of functions can be
selected.
indE. = Independent
dE. = Deviation
bAnd = Band
bAn.i. = Band with inhibition
prof = Profile of control during the
current segment AL1 output according
to program behaves.
AL2
STOP
Adjustable between 0.00 and 25.00 minutes.
If td = 0.00, derivation effect is not used.
Setting Pb = 0 this parameter is not seen.
Ct = Control period.
Adjustable between 1 and 250 seconds.
Setting Pb = 0 and C.ot.S.= Out1 this
parameter is not seen.
A1.St. A1.St. = The state of Alarm1.
If independent or deviation alarm is
Hi. selected, this parameter can be Lo.
P.SEt. = The ratio of output power at the set
AL1
point.Adjustable between 0% and 100%.
If this parameter is set to 0, the output power
becomes 0 at the set point. If it is adjusted to
50% output power becomes 50% at the set
point. Using this parameter the energy
requirements of the system is adjusted at the
set point. So the set point can be achieved by
minimum fluctuations and in the shortest time.
Setting Pb = 0, this parameter is not seen.
START
and Hi.. For Lo. alarm output is
energized below the alarm set point.
For Hi. alarm output is energized
above the alarm set point. If band
alarm is selected, this parameter can
be bIHI or boHI. bIHI means
alarm is activated inside the
band.boHI means alarm is activated
outside the band.
AL2
STOP
A1.P.e. A1.p.e. = State of Alarm1 output in
on the case of sensor failure.
C.HYS.
= Hysteresis of the control output.
Adjustable between 1 and 50 °C/F.
Adjustable between 0,1 and 50 °C/F ,if inp=Pt.0
Setting Pb = 0 this parameter is seen.
AL1
START
If A1.p.e.= On , the alarm output is
energized during the sensor failure.
If A1.p.e.= oFF, the alarm output is not
energized during the sensor failure.
AL2
STOP
C.StA. = Configuration of the control output.
C.StA. = HEAt means heating control.
C.StA. = cooL means cooling control.
Pr.Er. = This parameter is used to adjust the
control output during a sensor failure.
Adjustable between 0% and 100%.
If this parameter is adjusted to a value closer to
the energy requirements of the system at the set
point, process temperature is prevented to rise or
drop to dangerous levels.
START
= Alarm1 value upper limit.
If InP. or UnIt. parameters are changed,
the maximum value of the A1.H.L. parameter
changes to the maximum scale value of the
selected input type. Minimum of A1.H.L.
parameter is the value of A1.L.L. parameter.
AL2
STOP
A1.L.L.
0
C.ot.S.
START
STOP
A2.tp.
indE.
AL1
START
A1.L.L.
= Alarm1 value lower limit.
If InP. or UnIt. parameters are changed,
the minimum value of the A1.L.L. parameter
changes to the minimum scale value of the
selected input type. The maximum value is
the value of A1.H.L. parameter.
= Type of control output
out1 = Out1 control output.
0-20 = Analog control output.
( 0mA %0 energy, 20mA %100 energy )
Out1 = Alarm2 output.
4-20 = Analog control output.
( 4mA %0 energy, 20mA %100 energy )
Out1 = Alarm2 output.
s.s.r = SSR control output.
Out1=Alarm2 output.
C.Con. = Consistently control selection.
off = At the end of the profile, temperature
control is turned off.
on = At the end of the profile, temperature is kept
constant in last set value.
A2.Hy. = Hysteresis of the Alarm2
output.
Adjustable between 1 and 50°C.
AL2
AL2
STOP
AL1
A2.tP. =
Function of Alarm2 output.
Four kinds of functions can be
selected.
indE. = Independent
dE. = Deviation
bAnd = Band
bAn.i. = Band with inhibition
prof = Profile of control during the
current segment AL2 output according
to program behaves.
A2.St. =
A2.St.
Hi.
AL1
START
AL2
STOP
A2.P.e.
oFF
AL1
START
AL2
STOP
A2.H.L.
600
AL1
START
AL2
STOP
A2.L.L.
0
The state of Alarm2.
If independent or deviation alarm is
selected, this parameter can be Lo.
and Hi.. For Lo. alarm output is
energized below the alarm set point.
For Hi. alarm output is energized
above the alarm set point. If band
alarm is selected, this parameter can
be bIHI or boHI. bIHI means
alarm is activated inside the
band.boHI means alarm is activated
outside the band.
NOTE! If C.ot.S. = .out1, this
parameter is not seen.
A2.p.e. = State of Alarm2 output in
the case of sensor failure.
If A2.p.e.= On, the alarm output is
energized during the sensor failure.
If A2.p.e.= oFF, the alarm output is not
energized during the sensor failure.
NOTE! If C.ot.S. = .out1, this
parameter is not seen.
A2.H.L
= Alarm2 value upper limit.
If InP. or UnIt. parameters are changed,
the maximum value of the A2.H.L. parameter
changes to the maximum scale value of the
selected input type. Minimum of A2.H.L.
parameter is the value of A2.L.L. parameter.
A2.L.L.
= Alarm2 value lower limit.
If InP. or UnIt. parameters are changed, the minimum
value of the A2.L.L. parameter changes to the minimum
scale value of the selected input type. The maximum
value is the value of A2.H.L. parameter.
NOTE! If C.ot.S. = .out1, this parameter is not seen.
SET
CSET
C.HyS.
6
SET
CSET
C.HyS.
5
SET
CSET
C.HyS.
6
AL1
STOP
AL2
STOP
C.Lo.L.
0
AL1
START
AL2
STOP
oFFS.
0
AL1
START
AL2
STOP
Unit.
°C
AL1
START
AL2
STOP
fL.Co.
5
AL1
START
AL2
STOP
inP. = Type of input and scale.
Pt = Pt 100 -200 to +600°C
Pt.0 = Pt 100 -99.0 to +300.0°C
FE.cn. = J (Iron vs. Copper-Nickel) 0 to +600°C
nc.nA. = K (Nickel-Cr.vs. Nickel-Alum.) 0 to +1200°C
c.cn. = T (Copper vs. Copper-Nickel) 0 to +400°C
P10.r. = S (Platinum-10%Rhodium vs. Pt.) 0 to +1600°C
P13.r. = R (Platinum-13%Rhodium vs. Pt.) 0 to +1600°C
Note : If the selected input type is changed, the value of
C.Hi.L, C.Lo.L , A.Hi.L., A.Lo.L. parameters changes
automatically.
C.Hi.L. = Set point upper limit.
If InP. or UnIt. parameters are changed, the maximum
value of the C.Hi.L. parameter changes to the maximum
scale value of the selected input. The minimum value is
the value of C.Lo.L. parameter.
C.LoL. = Set point lower limit.
If InP. or UnIt. parameters are changed, the minimum
value of the C.Lo.L. parameter changes to the minimum
scale value of the selected input. The maximum value is
the value of C.Hi.L. parameter.
oFFS. = Offset value.
Offset value is added to the measurement value.
Adjusted between -99 and +99°C.
The normal value is 0.
UnIt
= The temperature unit.
Selectable as °C or °F.
Note : If the temperature unit is changed, the value of
the UPL., Lol., A.UP.L., A.Lo.L. Parameters changes
automatically.
NOTE! IfInp parameter is selected TC or Pt100, this
parameter is seen.
fL.Co.
= Coefficient of digital filter.
Filter for display value.
Adjustable between 1 and 32. If this parameter is 1,
digital filter runs most quick. If the parameter is 31, the
filter run most slow. The value of parameter should be
increased in interference.
t.bAs. t.bas. = Unit of time.
min As SEC. or mIn can be selected.
AL1
START
AL2
STOP
SEC. is selected,the time as second is shown.
min. is selected, the time as minute is shown.
Se.i.p. SE.i.p. = Segment increasing parameter.
SE.i.P. parameter can be set between the value in 0 and C.H.I.L parameters.
50 If S.num is selected between 1 and 8,the time value at the end of the process and
AL1
START
START
AL2
STOP
the difference between the target temperature value of SE.I.P. is equal to or smaller
then the next segment is passed.
If the S.num = 0 is selected,the difference between target temperature with process
value until from SE.IP value smaller than or equal ;timer is stopped and it does flash.
AL2
STOP
If Cont. is selected, the power is cutted-off and came back; running program will
continue where is resume.
s.num. s.num = Maximum segment number.
Can be selected between the 0-8. Selected numbers between 1-8,shows the step of
8 program to work with.Can be selected “0” is passed to the thermostat and timer
AL1
AL2
SET
CSET
key,the value of parameter flashes and
CSET
using
AL2
C.Hi.L.
600
AL1
SET
When holding
START
page 3/6
ASET
= The selection of action that the energy is given.
P.on.t. P.ont.
If StoP is selected, the running program is stopped when power is cutted-off and
Stop came back ;is returned to beginning of the program.It is expected to run again.
Modification of Parameter Diagram
C.HyS.
6
inP.
FE.cn.
START
A1.H.L
A1.H.L.
600
AL1
STOP
A2.Hy.
2
AL1
AL2
A1.tp.
indE.
Adjustable between 0.0 and 100.0 minutes.
If ti = 0.0, integral effect is not used.
Setting Pb = 0 this parameter is not seen.
AL2
ASET
PSET
ConF.
ASET
STOP
STOP
= Proportional band.
Adjustable between 0% and 100%
Setting Pb = 0% On-Off control is
selected.
ATTENTION! If C.ot.S
parameter is a .out 1
This MENU is not seen.
SET
keys the requested value can be adjusted.
If
key is pressed and held 0.6 seconds,the value of the
selected parameter changes rapidly.If waited enough,the
value increases 100 at each step. After 1 second following
the release of the key,initial condition is returned. The same
prodecure is valid for the decrement key.
START
d.adr. d.adr. = Device address.
Adjustable between 1 and 247. Difference addresses
1 should be selected for every device.
AL1
STOP
baud
off
mode.In this mode the timer works when the temperature reached the set value at the
end of this period and the Alarm1 contact be active.
d.sel. d.sel. = Display selection parameter.
It can take values between the 1-10. Can be selected “1”,only the process value is
1 shown. 2 and the above values are selected ;If 2 or more is programmed segment
AL2
AL1
START
STOP
Baud= Modbus baud rate.
START
AL2
profile, a segment number process value is shown alternately.
STOP
Selectable 1200, 2400, 4800 and 9600.
If baud= off, Modbus communication will be disable.
Note: The parameter appears at the devices which
become ModBus.
2/6
EPC4420-E-01-R
SET
PSET
ASET
SEGMENTS OF PROGRAMMING
SECU.
S.tun.
500
40.
CNT/AL2
page 2/6
ASET
AL2
STOP
C.SEt
150
AL1
START
PV
SV
STOP
S.cod.
0
C.SET = Auto PID parameters’s will
be found that temperature set value.
AL1
START
STOP
AL1
S.tu.E. = Auto PID parameter,the
finding parameter.
no = Selft tune is not done.
yES = Self tune is started.
START
STOP
AL2
STOP
A.AL.1
P.yES
AL1
START
AL2
STOP
A.AL.2
P.yES
AL1
START
AL2
STOP
A.CNF.
P.yES
AL1
START
AL2
STOP
A.tun.
yES
A.tu.E= Yes
?
70
TE.HI.
No
S.cod. = Security menu access
code.
It should be 666.
SET
SET
While device in running mode
key is
PSET
pressed to the segment programming mode is
passed.
PSET
AL2
A.Con.
P.yES
Temperature can begin the
process for self tune to
wait until fall.
SSR
AL1
AL2
S.tu.E.
yES
ASET
AL2
Before starting sef-tune
procedure, be sure A.tun
parameter is YES
in the SECU menu.
A.Con. = Parameter’s of CoN.o menu
access level code.
nonE = Invisible
P.yES = Modification can be done.
P. no = Only visible.
CNT/AL2
SSR
AL1
A.AL.1. =
Parameter’s of ALr.1
menu security level parameter.
nonE = Invisible
P.yES = Modification can be done.
P. no = Only visible.
= 1. Segment target temperature value
t.te.1 t.tE.1
SET
500 PSET key is being held
are set to the desired value by using keys.
AL2
AL1
START STOP
AL2
AL1
START
SSR
AL1
A.Al.2. = Parameter’s of A.Lr.2
STOP
ti.1
40
CNT/AL2
ti.1 =
PSET
AL2
AL1
key is being held
are set to the desired value by using keys.
START STOP
AL2
AL1
menu security level code.
nonE = Invisible
P.yES = Modification can be done.
P. no = Only visible.
1. Segment time value
SET
ti.1
40
CNT/AL2
STOP
START
SSR
AL1
A.CnF = Parameter’s of ConF menu
security level code.
nonE = Invisible
P.yES = Modification can be done.
P. no = Only visible.
AL1
CNT/AL2
SSR
ASET
START
AL1
ti.1
40
AL2
CNT/AL2
SSR
ASET
STOP
AL1
ti.1
40
AL1
key will be holding the
ASET
key as the AL1 output on or off can be
START
programmed.
With the
AL2
AL1
AL2
A.tun. = Parameter’s of S.tun. menu
security level code.
no = Invisible
yES = Self tune can be done.
or
key the AL2 output as on or off can be programmed.
START
STOP
ATTENTION!!! During check out the profile of the alarm outputs to be actived
before running a profile of A1.tP. and A2.tP. parameters must be set to as
Prof.
STOP
One of AL1 or AL2 keys are pressed continuesly 2sn,
returns from the segment programming mode.
Yes
All segments of the above processes are repeated.
No
Is it measured
temperature set value’s
to %60 equal or below
the this value’s?
Return to the normal running mode
Yes
AL2
AL1
Yes
START
25
Pid.t.
Is it measured
temperature set value’s
to %80 equal or above
this value’s?
Yes
100
P.SE.t.
CNT/AL2
Synchronized
to the measured temperature
value set?
SSR
AL1
t.te.8
500
t.tE.8 =
8. Segment target temperature value
SET
PSET
AL1
No
STOP
AL1
key is being held
AL2
START STOP
are set to the desired value by using keys.
AL2
No
START
CNT/AL2
Probe error is not,to the self tune mode is entered.The measured temperature is low
enough to make that self tune,PId.t. message is seen in sub-indicator and the self
tune process starts.For the self tune process to begin,measured temperature must
be to % 60 equal or under the set value’s.If this condition is not right , in the subindicator tE.HI. message flashes and the device can make self tune waits until the
temperature falls.When the temperature decreased, PId.t. message starts to flash
in the sub-indicator and self tune process is started and PID parameters can be
calculated until possible in the sub-indicator of this message continues to flash.
After PID parameters found in the sub-indicator P.SE.t. message starts to flash.
In this case,device PID controlled the heating till the set value and finding the
reqired amount of energy for being stabilished on the set level heating; returned
quitting the self tune mode and writing the P.SE.t. parameter as %.
SSR
AL1
STOP
ti.8
40
ti.8 =
8. Segment time value
SET
PSET
AL1
key is being held
AL2
START STOP
are set to the desired value by using keys.
If pressed on any keys while the PId.t. message flashes on sub-indicator, self tune
mode is quitted without accounting display PID parameters.
3/6
EPC4420-E-01-R
TIMER / THERMOSTAT OUTPUT EXAMPLES
S.NuM = 0
C.Con = on
Temperature
S.NuM = 0
C.Con = off
Temperature
t.te.1
t.te.1
se.i.P.
se.i.P.
Time
Time
AL1 Out
AL1 Out
START
START
key
key
ti.1
START
key
START
key
ti.1
Hold
ti.1
Time
ti.1+Hold
ti.1
ti.1
Time
PROFILE CONTROL OUTPUT EXAMPLES
Temperature
SNuM = 1
SNuM = 1
C.Con = on
C.Con = off
Temperature
t.te.1
t.te.1
se.i.P.
se.i.P.
Time
For single-step program S.num should be “1”.
Time
START
key
START
key
ti.1
ti.1
Time
ti.1
Time
ti.1
MULTI-STEP PROFILE CONTROL OUTPUT EXAMPLES
Seg2
Seg1
Target Temperature
Time
AL1
AL2
T.te.1 =100
Ti.1 = 30
ON
OFF
Seg4
Seg3
T.te.2 =100
Ti.2 = 20
OFF
ON
T.tE.3 =300
Ti.3 = 60
OFF
OFF
T.tE.4 = 300
Ti.4 = 40
ON
ON
Seg5
T.tE.5 =100
Ti.5 = 60
OFF
OFF
For five-step program S.num should be “5”.
AL1
AL2
Seg1
Seg2
Seg3
Seg4
Seg5
300°C
200°C
If C.Con = on
100°C
IfC.Con = oFF
Ti.1
Ti.2
Ti.3
Ti.4
Ti.5
30
20
60
40
60
Time (Minute or second)
The program returns to the
beginning from here.Waits to
start key pressing again.
4/6
EPC4420-E-01-R
TERMS
( 1 ) Measurement value (At running mode)
Parameter name (At programming mode)
( 2 ) Set value (At running mode)
Parameter value (At programming mode)
Timer run LED
( 3 ) Value increment key (At running and programming mode)
START key (At running mode)
Parameter selection key (At programming mode)
( 4 ) Value decrement key (At running and programming mode)
STOP key (At profile programming mode)
If only this key is pressed in running mode,software version number is seen.
Parameter selection key (At programming mode)
( 5 ) Alarm set key (At running mode)
Menu selection key (At programming mode)
EPC 4420
CNT/AL2
(7)
SSR
PV
AL1
R
TIMER
SET
AL1
PSET
START
ASET
ENDA
AL2
STOP
PROFILE CONTROLLER
( 6 ) The profile set values adjustment key (At running mode)
Parameter set key (At programming mode)
( 1 ) PV display
( 2 ) TIMER display
4 digits 7 segment red LED
4 digits 7 segment yellow LED
PV display :
7mm
TIMER display :7mm
Character heights
( 3 ),( 4 ),( 5 ),( 6 ) Keypad
( 7 ) State indicator
Mikro switch
3 red LEDs for Control, Alarm1 and SSR outputs
ALARM1 AND ALARM2 OUTPUT TYPES
Independent Alarm
A1.tP.=indE
SV
Band Alarm
A1.tP.= bAnd
Deviation Alarm
A1.tP.= DE.
SV
ON
SV
ON
ON
OFF
OFF A.StA.= Hi
ON
ON
ON
OFF
OFF A.StA.= Lo
OFF
a1.Hy.
A1.St.= boHi
OFF
A1.Hy.
A1.Hy..
A1.Hy.
SV-ASV
ASV
SV+ASV +300
(ASV min = beginning of scale -300
ASV max = end of scale)
(ASV min. =-300, ASV max. = +300)
(IfinP = Pt..0, ASV min. = -30.0,
ASV max. = +30.0)
SV = Set point of CONT output
ASV = Set point of alarm output
A1.St.= biHi
SV+ASV
300
300
SV =Set point of CONT output
ASV = Set point of AL1 output
(ASV min. = 0, ASV max. = +300)
(IfinP = Pt..0, ASV min. = 0.0, ASV max. = +30.0)
Band Alarm With Inhibition
A1.tP.= BAn.i.
SV+ASV
SV+ASV
SV
SV
SV-ASV
SV-ASV
ON
OFF
ON
OFF
Band alarm is possible
Band alarm is possible
Beginning
Beginning
of procedure
of procedure
SV =Set point of CONT output ASV = Set point of AL1 output (ASV min. = 0, ASV max. = 300 )
MODIFICATION OF CONTROL AND ALARM SET POINTS
PV
PV
130
150
SV
ASET
First, press and hold
A1.sE.
250
R
ASET
STOP
A1.sE.
249
PV
R
ASET
START
A1.sE.
250
PV
ASET
When CSET is released, it
returns to normal operation.
R
key, alarm setpoint value appears on the display. Then, the value is adjusted by using
keys.
START STOP
ASET
If C.ot.S different from out1. Alarm1 and Alarm2 setpoint values can be adjusted in sequence when per press
key.
ASET
NOTE: The maximum of C.SEt is the value of C.Hi.L. parameter and the minimum of it is the value of C.Lo.L. parameter.
If independent alarm is selected, A1.SE. and A2.SE.values can be adjusted between the limits of the full scale.
If deviation alarm is selected, A1.SE. and A2.SE. values can be adjusted between -300 and +300.
If band alarm is selected, A1.SE. and A2.SE. values can be adjusted between 0 and +300.
---150
Error Messages
PV
PV
---R
Temperature value is
higher than the scale
150
R
Temperature value is
lower than the scale
PFA
150
PV
R
Temperature sensor
is broken or over temperature
5/6
PSC
150
PV
R
Pt 100 or a sensor
line is short circuited
EPC4420-E-01-R
DIMENSIONS
Depth
87mm
For removing the device from
the panel:
- While pressing both side of
the device in direction 1, push it
in direction 2.
1
EPC 4420
CNT/AL2
48mm
58mm
SSR
PV
AL1
R
TIMER
SET
PSET
AL1
START
ASET
ENDA
AL2
STOP
PROFILE CONTROLLER
2
1
Connection
cables
Ambient temperature
measurement sensor
Panel cut-out
51mm
+0.6
mm
45
+0.6
mm
45
80mm
Flush mounting
clamp
Panel
Note 1) While panel mounting, additional distance required for
connection cables should be considered.
2) Panel thickness should be maximum 9mm.
3) If there is no 100mm free space at back side of the device,
it would be difficult to remove it from the panel.
CONNECTION DIAGRAM
ENDA EPC4420 is intended for installation in control panels. Make sure that the device is used only for intended
purpose. The shielding must be grounded on the instrument side. During an installation, all of the cables that are
connected to the device must be free of energy. The device must be protected against inadmissible humidity,
vibrations, severe soiling and make sure that the operation temperature is not exceeded. All input and output lines
that are not connected to the supply network must be laid out as shielded and twisted cables. These cables should
not be close to the power cables or components. The installation and electrical connections must be carried on by
a qualified staff and must be according to the relevant locally applicable regulations.
ENDA INDUSTRIAL ELECTRONICS
ENDA INDUSTRIAL ELECTRONICS
EPC4420-24VAC
PID PROFILE CONTROLLER
EPC4420-230VAC-RS
PID PROFILE CONTROLLER
+
-
RS- 485
A 1
9
B 2
10
3
RS-485 COM.
SSR / ANL
OUT
+
TC
Pt 100
-
+
-
4
11
5
12
6
13
7
14
8
15
230V AC +10% -20%
50/60Hz 5VA
1
9
2
10
3
SSR / ANL
OUT
CONT./AL2
AC 250V 2A
RESISTIVE LOAD
+
AL1
AC 250V 2A
RESISTIVE LOAD
TC
Pt 100
-
SN: XXXXXXXXX
+
-
11
4
5
6
13
7
14
8
15
24V AC ±10%
50/60Hz 5VA
CONT./AL2
12
AC 250V 2A
RESISTIVE LOAD
AL1
AC 250V 2A
RESISTIVE LOAD
Note 1) Mains supply cords shall meet the requirements
of IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the
power supply switch shall bring the identification of
the relevant instrument and it should be easily
accessible by the operator.
SN: XXXXXXXXX
NOTE :
SUPPLY :
184-253V AC
9
or 99-121V AC
10
50/60Hz 5VA
Logic output of the instrument is not electrically
insulated from the internal circuits. Therefore,
when using a grounding thermocouple, do not
connect the logic output terminals to the ground.
Line
Fuse
F 100 mA
250V AC
Holding screw
0.4-0.5Nm
switch
230V or 24V AC
Supply
Neutral
Fuse should
be connected.
Order Code : EPC4420-      - 
1
Cable size: 1,5mm²
SENSOR INPUT :
For J-K-T-S-R type thermocouple :
Use suitable compensation cables. Don't use
jointed cables. Pay attention to the polarities of the
thermocouple cables as shown in the figure right
are connected to the .
For resistance thermometer :
When 2 wired Pt 100 is used,
terminals 6 and 7 must be
short circuited.
Equipment is protected throughout
by DOUBLE INSULATION.
+
TC
7
-
8
+
-
6
Pt 100
7
2
1 - Supply Voltage
230VAC...230V AC
24VAC.....24V AC
SM...........9-30V DC / 7-24V AC
2- Modbus Option
RS........RS-485 Modbus communication
None....Don’t support RS-485 Modbus communication
8
SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.
Yukarý Dudullu Barbaros Cd. Kutup Sok. No:20 34775 - ÜMRANÝYE/ÝSTANBUL-TÜRKÝYE
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
6/6
url : www.enda.com.tr
EPC4420-E-01-R
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement