Hurricane 5301G
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
Hurricane 5301G
802.11b/g Wireless
ADSL2+ Modem / Router
User Manual
Version 1.0
2009-07-24
Page 1 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
o.i
r
Hardware connection for H5301G
Wall
Computer
Power
ww
w.
Sh
o
Socket
Telephone
Adapter
(Optional)
Micro Filter
LAN Port
Power switch
Page 2 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Contents
Intended Audience .................................................................................................................. 6
1.2
Definitions Of Terms Used In This Document......................................................................... 6
1.3
Acronyms Used Throughout This Document.......................................................................... 6
1.4
Usage Instructions .................................................................................................................. 6
1.5
Questions Or Comments On This Document ......................................................................... 6
r
1.1
System Overview ..................................................................................................................................... 7
2.1
General Description ................................................................................................................ 7
2.2
Specifications.......................................................................................................................... 7
2.2.1
ADSL Standard............................................................................................................... 7
2.2.2
Wireless Features .......................................................................................................... 7
2.2.3
Software Features.......................................................................................................... 8
2.2.4
Management .................................................................................................................. 8
ww
w.
Sh
o
2
Introduction .............................................................................................................................................. 6
o.i
1
3
4
Hardware Installation ............................................................................................................................... 9
3.1
Hardware Requirements......................................................................................................... 9
3.2
Hardware Setup Procedures .................................................................................................. 9
Software Configuration........................................................................................................................... 10
4.1
LAN Configuration ................................................................................................................ 12
4.2
Wireless Configuration........................................................................................................ 133
4.2.1
Basic Setting ................................................................................................................ 13
4.2.2
Advanced Settings ....................................................................................................... 14
4.2.3
Security ...................................................................................................................... 166
4.2.4
Access Control ............................................................................................................. 18
4.2.5
WPS ............................................................................................................................. 19
4.3
WAN Configuration ............................................................................................................... 21
4.3.1
Channel Configuration ................................................................................................. 21
4.3.2
ATM Setting.................................................................................................................. 23
4.3.3
ADSL Setting................................................................................................................ 24
4.4
Services Configuration.......................................................................................................... 25
4.4.1
DHCP Mode ................................................................................................................. 25
4.4.2
DHCP Server Configuration ......................................................................................... 25
4.4.3
DHCP Relay Configuration .......................................................................................... 26
4.4.4
DNS Configuration ....................................................................................................... 27
4.4.4.1
DNS Server ......................................................................................................... 27
4.4.4.2
Dynamic DNS...................................................................................................... 28
4.4.5
Firewall Configuration .................................................................................................. 30
Page 3 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
IP/Port Filtering.................................................................................................... 30
4.4.5.2
MAC Filtering....................................................................................................... 32
4.4.5.3
Port Forwarding................................................................................................... 34
4.4.5.4
DMZ..................................................................................................................... 35
4.4.5.5
URL Blocking....................................................................................................... 36
4.4.5.6
Domain blocking.................................................................................................. 37
r
4.4.5.1
IGMP Proxy Configuration ........................................................................................... 39
4.4.7
UPnP Configuration ..................................................................................................... 41
4.4.8
RIP Configuration......................................................................................................... 41
4.5
o.i
4.4.6
Advance Configuration ......................................................................................................... 43
Bridging ........................................................................................................................ 43
4.5.2
Routing......................................................................................................................... 44
4.5.3
SNMP Configuration .................................................................................................... 47
4.5.4
Port Mapping................................................................................................................ 48
4.5.5
IP QoS.......................................................................................................................... 49
4.5.6
Remote Access ............................................................................................................ 51
ww
w.
Sh
o
4.5.1
4.6
Diagnostic ............................................................................................................................. 52
4.6.1
4.7
Admin.................................................................................................................................... 53
4.7.1
Commit/Reboot ............................................................................................................ 53
4.7.2
Backup/Restore............................................................................................................ 54
4.7.3
System Log .................................................................................................................. 55
4.7.4
Password ..................................................................................................................... 55
4.7.5
Upgrade Firmware ..................................................................................................... 556
4.7.6
ACL .............................................................................................................................. 57
4.7.7
Time Zone .................................................................................................................... 58
4.7.8
TR-069 Config.............................................................................................................. 59
4.8
5
Diagnostic Test............................................................................................................. 52
Statistics................................................................................................................................ 61
4.8.1
Interfaces ..................................................................................................................... 61
4.8.2
ADSL............................................................................................................................ 62
Channel Mode Configuration ................................................................................................................. 63
5.1
Bridge Mode ......................................................................................................................... 63
5.2
MER(Mac Encapsulating Routing) Mode ............................................................................. 64
5.3
PPPoE Mode ........................................................................................................................ 65
5.4
PPPoA Mode ........................................................................................................................ 66
5.5
1483 Routed Mode ............................................................................................................. 667
Appendices ..................................................................................................................................................... 68
Appendix A: Protocol Stacks.................................................................................................................... 68
Page 4 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
A.1 1483 Bridged Model .............................................................................................. 68
5.5.2
A.2 1483 MER Model................................................................................................... 69
5.5.3
A.3 PPPoE Model ........................................................................................................ 70
5.5.4
A.4 PPPoA Model......................................................................................................... 71
5.5.5
A.5 1483 Routed Model ............................................................................................... 72
r
5.5.1
ww
w.
Sh
o
o.i
Appendix Product Support and Contact Information ................................. Error! Bookmark not defined.
Page 5 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
1 Introduction
r
The ADSL2+ Modem/Router user manual contains the guidance to install and configure
PROLiNK Hurricane 5301G Wireless ADSL2+ Modem/Router using the Web GUI.
1.1 Intended Audience
o.i
This manual is intended for end users to access ADSL broadband service.
1.2 Definitions Of Terms Used In This Document
None.
ww
w.
Sh
o
1.3 Acronyms Used Throughout This Document
None.
1.4 Usage Instructions
None.
1.5 Questions Or Comments On This Document
Please contact us and visit our website at http://www.prolink2u.com should you have any
questions or comments on this document.
Page 6 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
2 System Overview
2.1 General Description
ww
w.
Sh
o
o.i
r
Hurricane 5301G wireless router is a high-speed ADSL2+ Ethernet/Wireless
Modem/Router that is specifically designed to connect to the Internet and to directly
connect to your local area network (LAN) via high-speed 10/100 Mbps Ethernet, or
wireless LAN (WLAN). The ADSL2+ modem is compatible with the latest ADSL standards,
including ADSL2 and ADSL2+, and supports up to 24 Mbps downstream and 1.5 Mbps
upstream to deliver true broadband speed and throughput. The DSL router supports
wireless 802.11b/g and the following security protocols: WEP, WPA, WPA2, and 802.1x.
To ensure fully compatibility, the DSL device was tested with all major DSLAMs, and
support standard 10/100 Mbps Base-T Ethernet interface Auto MDI/MDIx 10/100 Switch
function allowing user easily to link to PC or other Switches/Hubs. The DSL device is an
idea solution for multi-users utilizing build-in channel mode (PPPoE/A, IPoA, IPoE), IP
routing, NAT functionalities sharing the ADSL link. The DSL device is also a perfect
solution for the residential users, it supports the users with bridge mode in host based
PPPoE Client.
2.2 Specifications
2.2.1 ADSL Standard
z
z
z
z
z
z
z
z
ITU-T G.992.1(G.dmt)
ANSI T1.413 Issue 2
G.992.2 (G.lite)
G.994.1 (G.hs)
Auto-negotiating rate adaptation
ADSL2 G.dmt.bis (G.992.3)
ADSL2 G.lite.bis (G.992.4)
ADSL2+ (G.992.5)
2.2.2 Wireless Features
z
z
z
z
z
Compilant with IEEE 802.11 B/G
Up to 54 Mbps wireless operation rate
64/128 bits WEP for security
WPA support
ACL (MAC address Filtering)
Page 7 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
o.i
RFC-1483/2684 LLC/VC-Mux bridged/routed mode
RFC-1577 Classical IP over ATM
RFC-2516 PPPoE
RFC-2364 PPPoA
ITU-T 1.610 F4/F5 OAM send and receive loop-back
802.1d Spanning-Tree Protocol
DHCP Client/Server/Relay
NAT
RIP v1/v2
DNS Relay Agent
DMZ support
IGMP Proxy/Snooping
Stateful Packet Inspection
Protection against Denial of Service attacks
IP Packet Filtering
QoS
Dynamic DNS
UPnP support
ww
w.
Sh
o
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
z
r
2.2.3 Software Features
2.2.4 Management
z
z
z
z
z
z
z
Web-based Configuration
Menu-driven Command-line Interpreter
Telnet Remote Management
SNMP v1/v2/Trap
Firmware upgrade through FTP, TFTP and HTTP
Configuration backup/restore
Diagnostic Tool
Page 8 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
3 Hardware Installation
3.1 Hardware Requirements
r
12V Power Adapter
RJ-45 Ethernet cable
RJ-11 ADSL line
o.i
z
z
z
3.2 Hardware Setup Procedures
ww
w.
Sh
o
1. Connect RJ-11 line from Hurricane 5301G to the wall phone socket
2. Connect RJ-45 line from your PC LAN Port to Hurricane 5301G Ethernet port
3. Connect the 12V power adapter
Page 9 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4 Software Configuration
r
The DSL device is an ADSL2+ wireless router. When you power on the device, the system
will boot up and connect to ADSL automatically. The system provides a PVC for bridge test
by default. The default configurations for the system are listed below.
LAN IP address: 192.168.1.1, NetMask: 255.255.255.0
UART setting: 115200bps, 8 bits, no parity, 1 stop bit, no flow control.
z
z
VPI/VCI for ATM: 0/35
ADSL Line mode: Auto-detect.
o.i
z
z
ww
w.
Sh
o
User can change settings via WEB browser. The following sections describe the set up
procedures.
Please set your PC’s Ethernet port as follow:
z
z
IP address: 192.168.1.XXX (e.g. 192.168.1.10)
NetMask: 255.255.255.0
Access the Web Console:
z
z
Start your web browser.
Type the Ethernet IP address of the modem/router on the address bar of the browser.
Default IP address is 192.168.1.1.
z
The Enter Network Password dialog box appears. Default Username: admin
password
Page 10 of 73
Password:
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
Once you have connected to ADSL2+ router. You will see the status page.
This page displays the ADSL modem/router’s current status and settings. This information
is read-only except for the PPPoE/PPPoA channel for which user can connect/disconnect
the channel on demand. Click the “Refresh” button to update the status
Function buttons in this page:
Connect / Disonnect
The two buttons take effect only when PVC is configured as PPPoE/PPPoA mode. Click
Connect/Disconnect button to connect/disconnect the PPP dial up link.
.
Page 11 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.1 LAN Configuration
ww
w.
Sh
o
o.i
r
This page shows the current setting of LAN interface. You can set IP address, subnet mask,
and IGMP Snooping for LAN interface in this page.
Fields in this page:
Field
Description
IP Address
The IP address your LAN hosts use to identify the device’s LAN port.
Subnet Mask
LAN subnet mask.
IGMP Snooping
Enable/disable the IGMP snooping function for the multiple bridged LAN ports.
Function buttons in this page:
Apply Changes
Click to save the setting to the configuration. New parameters will take effect after
save into flash memory and reboot the system. See section “Admin” for save details.
Undo
Discard your changes.
Page 12 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.2 Wireless Configuration
This section provides the wireless network settings for your WLAN interface. The wireless
interface enables the wireless AP function for ADSL modem.
r
4.2.1 Basic Setting
ww
w.
Sh
o
o.i
This page contains all of the wireless basic settings. Most users will be able to configure
the wireless portion and get it working properly using the setting on this screen.
Fields in this page:
Field
Description
Disable Wireless LAN
Check it to disable the wireless function for ADSL modem.
Interface
Band
Select the appropriate band from the list provided to correspond with your network
setting.
Mode
The selections are: AP
SSID
The Service Set Identifier (SSID) or network name. It is case sensitive and must not
exceed 32 characters, which may be any keyboard character. The mobile wireless
stations shall select the same SSID to be able to communicate with your ADSL
modem (or AP).
Page 13 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Channel Number
Select the appropriate channel from the list provided to correspond with your
network settings. You shall assign a different channel for each AP to avoid signal
interference.
The maximum output power: 15mW, 30mW or 60mW.
r
Radio Power (mW)
Function buttons in this page:
o.i
Associated Clients
Click it will show the clients currently associated with the ADSL modem.
Apply Changes
Change the settings. New parameters will take effect after save into flash memory and
reboot the system. See section “Admin” for save details.
ww
w.
Sh
o
Reset
Discard your changes and reload all settings from flash memory.
4.2.2 Advanced Settings
This page allows advanced users who have sufficient knowledge of wireless LAN. These
setting shall not be changed unless you know exactly what will happen for the changes you
made on your DSL device.
Page 14 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Fields in this page:
Field
Description
Authentication Type
Open System: Open System authentication is not required to be successful while a
client may decline to authenticate with any particular other client.
r
Shared Key: Shared Key is only available if the WEP option is implemented. Shared
Key authentication supports authentication of clients as either a member of those
who know a shared secret key or a member of those who do not. IEEE 802.11
o.i
Shared Key authentication accomplishes this without the need to transmit the secret
key in clear. Requiring the use of the WEP privacy mechanism.
Auto: Auto is the default authentication algorithm. It will change its authentication
type automatically to fulfill client’s requirement.
Fragment Threshold
This value should remain at its default setting of 2346. It specifies the maximum size
for a packet before data is fragmented into multiple packets. If you experience a high
ww
w.
Sh
o
packet error rate, you may slightly increases the “Fragment Threshold” value within
the value range of 256 to 2346. Setting this value too low may result in poor network
performance. Only minor modifications of this value are recommended.
RTS Threshold
This value should remain at its default setting of 2347. Should you encounter
inconsistent data flow, only minor modifications are recommended. If a network
packet is smaller than the preset “RTS threshold” size, the RTS/CTS mechanism will
not be enabled. The ADSL modem (or AP) sends Request to Send (RTS) frames to
a particular receiving station and negotiates the sending of a data frame. After
receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to
acknowledge the right to begin transmission.
Beacon Interval
The Beacon Interval value indicates the frequency interval of the beacon. Enter a
value between 20 and 1024. A beacon is a packet broadcast by the ADSL modem
(or AP) to synchronize the wireless network. The default is 100.
Data Rate
The rate of data transmission should be set depending on the speed of your wireless
network. You should select from a range of transmission speeds, or you can select
Auto to have the ADSL modem (or AP) automatically use the fastest possible data
rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best
possible connection speed between the AP and a wireless client. The default setting
is Auto.
Preamble Type
The Preamble Type defines the length of the CRC (Cyclic Redundancy Check) block
for communication between the AP and mobile wireless stations. Make sure to select
the appropriate preamble type. Note that high network traffic areas should use the
short preamble type. CRC is a common technique for detecting data transmission
errors.
Broadcast SSID
If this option is enabled, the device will automatically transmit their network name
Page 15 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
(SSID) into open air at regular interval. This feature is intended to allow clients to
dynamically discover and roam between WLANs; if this option is disabled, the device
will hide its SSID. When this is done, the station cannot directly discover its WLAN
and MUST be configure with the SSID. Note that in a home Wi-Fi network, roaming
r
is largely unnecessary and the SSID broadcast feature serves no useful purpose.
You should disable this feature to improve the security of your WLAN.
When Relay Blocking is enabled, wireless clients will not be able to directly access
other wireless clients.
Ethernet to Wireless
o.i
Relay Blocking
When enabled, traffic between Ethernet and wireless interfaces are not allowed.
Blocking
Function buttons in this page:
ww
w.
Sh
o
Apply Changes
Change the settings. New parameters will take effect after save into flash memory and
reboot the system. See section “Admin” for save details.
Reset
Discard your changes and reload all settings from flash memory.
4.2.3 Security
This screen allows you to setup the wireless security. Turn on WEP or WPA by using
encryption keys could prevent any unauthorized access to your WLAN.
Fields in this page:
Page 16 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Field
Description
Encryption
There are 4 types of security to be selected. To secure your WLAN, it’s strongly
recommended to enable this feature.
WEP: Make sure that all wireless devices on your network are using the same
r
encryption level and key. Click Set WEP Key button to set the encryption key.
WPA (TKIP): WPA uses Temporal Key Integrity Protocol (TKIP) for data encryption.
TKIP utilized a stronger encryption method and incorporates Message Integrity Code
WPA2 (AES):
o.i
(MIC) to provide protection against hackers.
WPA2, also known as 802.11i, uses Advanced Encryption Standard
(AES) for data encryption. AES utilized a symmetric 128-bit block data encryption.
WAP2 Mixed: The AP supports WPA (TKIP) and WPA2 (AES) for data encryption.
The actual selection of the encryption methods will depend on the clients.
Check it to enable 802.1x authentication. This option is selectable only when the
Authentication
“Encryption” is choose to either None or WEP. If the “Encryption” is WEP, you need
ww
w.
Sh
o
Use 802.1x
to further select the WEP key length to be either WEP 64bits or WEP 128bits.
WPA Authentication
There are 2 types of authentication mode for WPA.
Mode
WPA-RADIUS: WPA RADIUS uses an external RADIUS server to perform user
authentication. To use WPA RADIUS, enter the IP address of the RADIUS server,
the RADIUS port (default is 1812) and the shared secret from the RADIUS server.
Please refer to “Authentication RADIUS Server” setting below for RADIUS setting.
The WPA algorithm is selected between TKIP and AES, please refer to “WPA cipher
Suite” below.
Pre-Shared Key: Pre-Shared Key authentication is based on a shared secret that is
known only by the parties involved. To use WPA Pre-Shared Key, select key format
and enter a password in the “Pre-Shared Key Format” and “Pre-Shared Key” setting
respectively. Please refer to “Pre-Shared Key Format” and “Pre-Shared Key” setting
below.
Pre-Shared Key
PassPhrase: Select this to enter the Pre-Shared Key secret as user-friendly textual
Format
secret.
Hex (64 characters): Select this to enter the Pre-Shared Key secret as hexadecimal
secret.
Pre-Shared Key
Specify the shared secret used by this Pre-Shared Key. If the “Pre-Shared Key
Format” is specified as PassPhrase, then it indicates a passphrase of 8 to 63 bytes
long; or if the “Pre-Shared Key Format” is specified as PassPhrase, then it indicates
a 64-hexadecimal number.
Authentication RADIUS If the WPA-RADIUS is selected at “WPA Authentication Mode”, the port (default is
Server
1812), IP address and password of external RADIUS server are specified here.
Page 17 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Function buttons in this page:
r
Apply Changes
Change the settings. New parameters will take effect after save into flash memory and reboot
the system. See section “Admin” for save details.
4.2.4 Access Control
ww
w.
Sh
o
o.i
This page allows administrator to have access control by enter MAC address of client
stations. When Enable this function, MAC address can be added into access control list
and only those clients whose wireless MAC address are in the access control list will be
able to connect to your DSL device (or AP).
Fields in this page:
Field
Description
Wireless Access
The Selections are:
Control Mode
Disable
Disable the wireless ACL feature.
Allow Listed
When this option is selected, no wireless clients except those whose MAC
addresses are in the current access control list will be able to connect (to this
Page 18 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
device).
Deny Listed
When this option is selected, all wireless clients except those whose MAC
addresses are in the current access control list will be able to connect (to this
MAC Address
r
device).
Enter client MAC address and press “Apply Changes” button to add client MAC
Function buttons for the setting block:
Apply Changes
o.i
address into current access control list.
ww
w.
Sh
o
Click to add this entry into the Current Access Control List.
The Current Access Control List lists the client MAC addresses. Any wireless client with its MAC
address listed in this access control list will be able to connect to the device. You can select the
entries at the Select column and apply to the following function buttons.
Function buttons for the Current Access Control List:
Delete Selected
Delete the selected entries from the list.
Delete All
Flush the list.
4.2.5 WPS
Although home Wi-Fi networks have become more and more popular, users still have
trouble with the initial set up of network. This obstacle forces users to use the open security
and increases the risk of eavesdropping. Therefore, The Wi-Fi Protected Setup (WPS) is
designed to ease set up of security-enabled Wi-Fi networks and subsequently network
management (Wi-Fi Protected Setup Specification 1.0h.pdf, p. 8).
The largest difference between WPS-enabled devices and legacy devices is that users do
not need the knowledge about SSID, channel and security settings, but they could still surf
in a security-enabled Wi-Fi network.
This device supports Push Button method and PIN method for WPS. The following
sub-paragraphs will describe the function of each item. The webpage is as below.
Page 19 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
Fields in this page:
Field
Description
Disable WPS
Check to disable the Wi-Fi protected Setup.
WPS Status
When AP’s settings are factory default (out of box), it is set to open security and
un-configured state. “WPS Status” will display it as “UnConfigured”. If it already
shows “Configured”, some registrars such as Vista WCN will not configure AP. Users
will need to go to the “Backup/Restore” page and click “Reset” to reload factory
default settings.
Self-PIN Number
“Self-PIN Number” is AP’s PIN. Whenever users want to change AP’s PIN, they
could click “Regenerate PIN” and then click “ Apply Changes”. Moreover, if users
want to make their own PIN, they could enter four-digit PIN without checksum and
then click “ Apply Changes”. However, this would not be recommended since the
registrar side needs to be supported with four-digit PIN.
Push Button
Clicking this button will invoke the PBC method of WPS. It is only used when AP acts
Configuration
as a registrar.
Client PIN Number
It is only used when users want their station to join AP’s network. The length of PIN
is limited to four or eight numeric digits. If users enter eight-digit PIN with checksum
error, there will be a warning message popping up. If users insist on this PIN, AP will
Page 20 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
take it.
Regenerate PIN
Click to regenerate the Self-PIN Number.
Apply Changes
Click to commit changes.
Reset
It restores the original values.
ww
w.
Sh
o
Start PIN
Click to start the PIN method of WPS.
o.i
Start PBC
Click to start the Push Button method of WPS.
r
Function buttons in this page:
4.3 WAN Configuration
There are three sub-menu for WAN configuration: [Channel Config], [ATM Settings], and
[ADSL Settings].
4.3.1 Channel Configuration
ADSL modem/router comes with 8 ATM Permanent Virtual Channels (PVCs) at the most.
There are mainly three operations for each of the PVC channels: add, delete and modify.
And there are several channel modes to be selected for each PVC channel. For each of
the channel modes, the setting is quite different accordingly. Please reference to the
section – Channel Mode Configuration for details.
Page 21 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
r
Function buttons in this page:
Add
o.i
Click Add to complete the channel setup and add this PVC channel into configuration.
Modify
Select an existing PVC channel by clicking the radio button at the Select column of the
Current ATM VC Table before we can modify the PVC channel. After selecting an
PVC channel, we can modify the channel configuration at this page. Click Modify to
complete the channel modification and apply to the configuration.
ww
w.
Sh
o
Delete
Select an existing PVC channel to be deleted by clicking the radio button at the Select
column of the Current ATM VC Table. Click Delete to delete this PVC channel from
configuration.
Page 22 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.3.2 ATM Setting
ww
w.
Sh
o
o.i
r
The page is for ATM PVC QoS parameters setting. The DSL device support 4 QoS
mode —CBR/rt-VBR/nrt-VBR/UBR.
Fields in this page:
Field
Description
VPI
Virtual Path Identifier. This is read-only field and is selected on the Select column in
the Current ATM VC Table.
VCI
Virtual Channel Identifier. This is read-only field and is selected on the Select
column in the Current ATM VC Table. The VCI, together with VPI, is used to identify
the next destination of a cell as it passes through to the ATM switch.
QoS
Quality of Server, a characteristic of data transmission that measures how accurately
and how quickly a message or data is transferred from a source host to a destination
host over a network. The four QoS options are:
−
UBR (Unspecified Bit Rate): When UBR is selected, the SCR and
MBS fields are disabled.
−
CBR (Constant Bit Rate): When CBR is selected, the SCR and MBS
fields are disabled.
−
nrt-VBR (non-real-time Variable Bit Rate): When nrt-VBR is
selected, the SCR and MBS fields are enabled.
−
rt-VBR (real-time Variable Bit Rate): When rt-VBR is selected, the
SCR and MBS fields are enabled.
PCR
Peak Cell Rate, measured in cells/sec., is the cell rate which the source may never
Page 23 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
exceed.
SCR
Sustained Cell Rate, measured in cells/sec., is the average cell rate over the
duration of the connection.
MBS
Maximum Burst Size, a traffic parameter that specifies the maximum number of cells
o.i
Function buttons in this page:
r
that can be transmitted at the peak cell rate.
Apply Changes
Set new PVC OoS mode for the selected PVC. New parameters will take effect after
save into flash memory and reboot the system. See section “Admin” for save details.
ww
w.
Sh
o
Undo
Discard your settings.
4.3.3 ADSL Setting
The ADSL setting page allows you to select any combination of DSL training modes.
Page 24 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Fields in this page:
Field
Description
ADSL modulation
Choose prefered xdsl standard protocols.
G.lite : G.992.2 Annex A
T1.413 : T1.413 issue #2
ADSL2 : G.992.3 Annex A
o.i
ADSL2+ : G.992.5 Annex A
r
G.dmt : G.992.1 Annex A
AnnexL Option
Enable/Disable ADSL2/ADSL2+ Annex L capability.
AnnexM Option
Enable/Disable ADSL2/ADSL2+ Annex M capability.
ADSL Capability
“Bitswap Enable” : Enable/Disable bitswap capability.
ww
w.
Sh
o
“SRA Enable” : Enable/Disable SRA (seamless rate adaptation) capability.
Function buttons in this page:
Tone Mask
Choose tones to be masked. Mased tones will not carry any data.
Apply Changes
Click to save the setting to the configuration and the modem will be retrained.
4.4 Services Configuration
4.4.1 DHCP Mode
You can configure your network and DSL device to use the Dynamic Host Configuration
Protocol (DHCP). This page provides DHCP instructions for implementing it on your
network by selecting the role of DHCP protocol that this device wants to play. There are
two different DHCP roles that this device can act as: DHCP Serve and DHCP Relay. When
acting as DHCP server, you can setup the server parameters at the DHCP Server page;
while acting as DHCP Relay, you can setup the relay at the DHCP Relay page.
4.4.2 DHCP Server Configuration
By default, the device is configured as a DHCP server, with a predefined IP address pool of
192.168.1.64 through 192.168.1.253 (subnet mask 255.255.255.0).
Page 25 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
Fields in this page:
Field
Description
IP Pool Range
Specify the lowest and highest addresses in the pool.
Max Lease Time
The Lease Time is the amount of time that a network user is allowed to maintain a
network connection to the device using the current dynamic IP address. At the end of
the Lease Time, the lease is either renewed or a new IP is issued by the DHCP
server. The amount of time is in units of seconds. The default value is 86400
seconds (1 day). The value –1 stands for the infinite lease.
Domain Name
A user-friendly name that refers to the group of hosts (subnet) that will be assigned
addresses from this pool.
Function buttons in this page:
Apply Changes
Set new DHCP server configuration. New parameters will take effect after save into
flash memory and reboot the system. See section “Admin” for save details.
Undo
Discard your changes.
4.4.3 DHCP Relay Configuration
Some ISPs perform the DHCP server function for their customers’ home/small office
Page 26 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
network. In this case, you can configure this device to act as a DHCP relay agent. When a
host on your network requests Internet access, the device contacts your ISP to obtain the
IP configuration, and then forward that information to the host. You should set the DHCP
mode after you configure the DHCP relay.
Fields in this page:
Field
Description
DHCP Server Address Specify the IP address of your ISP’s DHCP server. Requests for IP information from
your LAN will be passed to the default gateway, which should route the request
appropriately.
Function button in this page
Apply Changes
Click to save the setting to the configuration.
4.4.4 DNS Configuration
There are two submenus for the DNS Configuration: [DNS Server] and [Dynamic DNS]
4.4.4.1
DNS Server
This page is used to select the way to obtain the IP addresses of the DNS servers.
Page 27 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
o.i
r
User Manual
ww
w.
Sh
o
Fields in this page:
Field
Description
Attain DNS
Automatically
Select this item if you want to use the DNS servers obtained by the WAN
interface via the auto-configuration mechanism.
Set DNS Manually
Select this item to configure up to three DNS IP addresses.
Function buttons in this page:
Apply Changes
Set new DNS relay configuration. New parameters will take effect after save into flash
memory and reboot the system. See section “Admin” for save details.
Undo
Discard your changes.
4.4.4.2
Dynamic DNS
Each time your device connects to the Internet, your ISP assigns a different IP address to
your device. In order for you or other users to access your device from the WAN-side, you
need to manually track the IP that is currently used. The Dynamic DNS feature allow you to
register your device with a DNS server and access your device each time using the same
host name. The Dynamic DNS page allows you to enable/disable the Dynamic DNS feature.
Page 28 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
On the Dynamic DNS page, configure the following fields:
Field
Description
Enable
Check this item to enable this registration account for the DNS server.
DDNS provider
There are two DDNS providers to be selected in order to register your device
with: DynDNS and TZO. A charge may occurs depends on the service you
select.
Hostname
Domain name to be registered with the DDNS server.
Interface
This field defaults to your device’s WAN interface over which your device
will be accessed.
Username
User-name assigned by the DDNS service provider.
Password
Password assigned by the DDNS service provider.
Function buttons in this page:
Add
Click Add to add this registration into the configuration.
Remove
Select an existing DDNS registration by clicking the radio button at the Select column
of the Dynamic DNS Table. Click Remove button to remove the selected registration
from the configuration.
Page 29 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.5 Firewall Configuration
Firewall contains several features that are used to deny or allow traffic from passing
through the device.
IP/Port Filtering
ww
w.
Sh
o
o.i
r
4.4.5.1
The IP/Port filtering feature allows you to deny/allow specific services or applications in the
forwarding path.
Fields on the first setting block:
Field
Description
Outgoing Default Action Specify the default action on the LAN to WAN forwarding path.
Incoming Default Action Specify the default action on the WAN to LAN forwarding path.
Function button for this first setting block:
Apply Changes
Click to save the setting of default actions to the configuration.
Fields on the second setting block:
Field
Description
Rule Action
Deny or allow traffic when matching this rule.
Direction
Traffic forwarding direction.
Page 30 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
There are 3 options available: TCP, UDP and ICMP.
Src IP Address
The source IP address assigned to the traffic on which filtering is applied.
Src Subnet Mask
Subnet-mask of the source IP.
Src Port
Starting and ending source port numbers.
Dst IP Address
The destination IP address assigned to the traffic on which filtering is
applied.
Dst Subnet Mask
Subnet-mask of the destination IP.
Dst Port
Starting and ending destination port numbers.
o.i
r
Protocol
Function buttons for this second setting block:
Apply Changes
Click to save the rule entry to the configuration.
Function buttons for the Current Filter Table:
ww
w.
Sh
o
Delete Selected
Delete selected filtering rules from the filter table. You can click the checkbox at the
Select column to select the filtering rule.
Delete All
Delete all filtering rules from the filter table.
Page 31 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.5.2
MAC Filtering
ww
w.
Sh
o
o.i
r
The MAC filtering feature allows you to define rules to allow or deny frames through the
device based on source MAC address, destination MAC address, and traffic direction.
iel
Fields on the first setting block:
Field
Description
Outgoing Default Action Specify the default action on the LAN to WAN bridging/forwarding path.
Incoming Default Action Specify the default action on the WAN to LAN bridging/forwarding path.
Function button for this first setting block:
Apply Changes
Click to save the setting of default actions to the configuration.
Fields on the second setting block:
Field
Description
Rule Action
Deny or allow traffic when matching this rule.
Direction
Traffic bridging/forwarding direction.
Src MAC Address
he source MAC address. It must be xxxxxxxxxxxx format. Blanks can be used in the
Page 32 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
MAC address space and are considered as don’t care.
Dst MAC Address
The destination MAC address. It must be xxxxxxxxxxxx format. Blanks can be used
Function buttons for this second setting block:
o.i
Apply Changes
Click to save the rule entry to the configuration.
r
in the MAC address space and are considered as don’t care.
Function buttons for the Current Filter Table:
Delete Selected
Delete selected filtering rules from the filter table. You can click the checkbox at the
Select column to select the filtering rule.
ww
w.
Sh
o
Delete All
Delete all filtering rules from the filter table.
Page 33 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.5.3
Port Forwarding
ww
w.
Sh
o
o.i
r
Firewall keeps unwanted traffic from the Internet away from your LAN computers. Add a
Port Forwarding entry will create a tunnel through your firewall so that the computers on
the Internet can communicate to one of the computers on your LAN on a single port.
Fields in this page:
Field
Description
Enable Port Forwarding Check this item to enable the port-forwarding feature.
Protocol
There are 3 options available: TCP, UDP and Both.
Enable
Check this item to enable this entry.
Local IP Address
IP address of your local server that will be accessed by Internet.
Port
The destination port number that is made open for this application on the LAN-side.
Remote IP Address
The source IP address from which the incoming traffic is allowed. Leave blank for all.
External Port
The destination port number that is made open for this application on the WAN-side
Interface
Select the WAN interface on which the port-forwarding rule is to be applied.
Page 34 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Function buttons for the setting block:
Apply Changes
Click to save the rule entry to the configuration.
Function buttons for the Current Port Forwarding Table:
r
Delete Selected
Delete the selected port forwarding rules from the forwarding table. You can click the
checkbox at the Select column to select the forwarding rule.
4.4.5.4
DMZ
o.i
Delete All
Delete all forwarding rules from the forwarding table.
ww
w.
Sh
o
A DMZ (Demilitarized Zone) allows a single computer on your LAN to expose ALL of its
ports to the Internet. Enter the IP address of that computer as a DMZ (Demilitarized Zone)
host with unrestricted Internet access. When doing this, the DMZ host is no longer behind
the firewall.
Fields in this page:
Field
Description
Enable DMZ
Check this item to enable the DMZ feature.
DMZ Host IP Address
IP address of the local host. This feature sets a local host to be exposed to the
Internet.
Function buttons in this page:
Apply Changes
Click to save the setting to the configuration.
Page 35 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.5.5
URL Blocking
ww
w.
Sh
o
o.i
r
The URL Blocking is the web filtering solution. The firewall includes the ability to block
access to specific web URLs based on string matches. This can allow large numbers of
URLs to be blocked by specifying only a FQDN (such as tw.yahoo.com). The URL Blocking
enforce a Web usage policy to control content downloaded from, and uploaded to, the
Web.
Fields in this page:
Field
Description
URL Blocking capability Check this item to enable the URL Blocking feature.
FQDN
A fully qualified domain name (or FQDN) is an unambiguous domain name that
specifies the node's position in the DNS tree hierarchy absolutely, such as
tw.yahoo.com. The FQDN will be blocked to access.
Keyword
The filtered keyword such as yahoo. If the URL includes this keyword, the URL will
be blocked to access.
Page 36 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Function buttons in this page:
Apply Changes
Click to disable/enable the URL Blocking capability
Add FQDN
Add FQDN into URL Blocking table.
o.i
at the Select column to select the Blocked FQDN.
r
Delete Selected FQDN
Delete the selected FQDN from the URL Blocking table. You can click the checkbox
Add Filtered Keyword
Add filtered keyword into Keyword Filtering table.
Delete Selected Keyword
Delete the selected keyword from the keyword Filtering table. You can click the
ww
w.
Sh
o
checkbox at the Select column to select the filtered keyword.
4.4.5.6
Domain blocking
The firewall includes the ability to block access to specific domain based on string matches.
For example, if the URL of Taiwan Yahoo web site is “tw.yahoo.com” and you enter
“yahoo.com”, the firewall will block all the DNS queries with “yahoo.com” string. So the
Host will be blocked to access all the URLs belong to “yahoo.com” domain. That means
you can protect your computer, your house, your office and anything else that uses DNS
from being able to service domains that you don’t want to load.
Page 37 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Fields in this page:
Field
Description
Domain Blocking capability Check this item to enable the Domain Blocking feature.
Domain
The blocked domain. If the URL of Taiwan Yahoo web site is tw.yahoo.com, the
o.i
Function buttons in this page:
r
domain can be yahoo.com.
Apply Changes
Click to disable/enable the Domain Block capability
Add Domain
Add domain into Domain Block table.
ww
w.
Sh
o
Delete Selected Domain
Delete the selected domain from the Domain Block table. You can click the checkbox
at the Select column to select the Blocked domain.
Page 38 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.6 IGMP Proxy Configuration
ww
w.
Sh
o
o.i
r
Multicasting is useful when the same data needs to be sent to more than one hosts. Using
multicasting as opposed to sending the same data to the individual hosts uses less
network bandwidth. The multicast feature also enables you to receive multicast video
stream from multicast servers.
IP hosts use Internet Group Management Protocol (IGMP) to report their multicast group
memberships to neighboring routers. Similarly, multicast routers use IGMP to discover
which of their hosts belong to multicast groups. This device supports IGMP proxy that
handles IGMP messages. When enabled, this device acts as a proxy for a LAN host
making requests to join and leave multicast groups, or a multicast router sending multicast
packets to multicast group on the WAN side.
When a host wishes to join a multicast group, it sends IGMP REPORT message to the
device’s IGMP downstream interface. The proxy sets up a multicast route for the interface
and host requesting the video content. It then forwards the Join to the upstream multicast
router. The multicast IP traffic will then be forwarded to the requesting host. On a leave, the
proxy removes the route and then forwards the leave to the upstream multicast router.
The IGMP Proxy page allows you to enable multicast on WAN and LAN interfaces. The
LAN interface is always served as downstream IGMP proxy, and you can configure one of
the available WAN interfaces as the upstream IGMP proxy.
„
„
Upstream: The interface that IGMP requests from hosts are sent to the multicast
router.
Downstream: The interface data from the multicast router are sent to hosts in the
multicast group database.
Fields in this page:
Field
Description
IGMP Proxy
Enable/disable IGMP proxy feature
Page 39 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Proxy Interface
The upstream WAN interface is selected here.
ww
w.
Sh
o
Undo
Discard your settings.
o.i
Apply Changes
Click to save the setting to the configuration.
r
Function buttons in this page:
Page 40 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.4.7 UPnP Configuration
The DSL device supports a control point for Universal Plug and Play (UPnP) version 1.0,
ww
w.
Sh
o
o.i
r
and supports two key features: NAT Traversal and Device Identification. This feature
requires one active WAN interface. In addition, the host should support this feature. In the
presence of multiple WAN interfaces, select an interface on which the incoming traffic is
present.
With NAT Traversal, when an UPnP command is received to open ports in NAT, the
application translates the request into system commands to open the ports in NAT and the
firewall. The interface to open the ports on is given to UPnP when it starts up and is part of
the configuration of the application.
For Device Identification, the application will send a description of the DSL device as a
control point back to the host making the request.
Fields in this page:
Field
Description
UPnP Daemon
Enable/disable UPnP feature.
Binded WAN Interface Select WAN interface that will use UPnP from the drop-down lists.
Function buttons in this page:
Apply Changes
Click to save the setting to the system configuration.
4.4.8 RIP Configuration
RIP is an Internet protocol you can set up to share routing table information with other
routing devices on your LAN, at your ISP’s location, or on remote networks connected to
your network via the ADSL line.
Most small home or office networks do not need to use RIP; they have only one router,
such as the ADSL Router, and one path to an ISP. In these cases, there is no need to
share routes, because all Internet data from the network is sent to the same ISP gateway.
Page 41 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
You may want to configure RIP if any of the following circumstances apply to your network:
Your home network setup includes an additional router or RIP-enabled PC
(other than the ADSL Router). The ADSL Router and the router will need to
communicate via RIP to share their routing tables.
−
Your network connects via the ADSL line to a remote network, such as a
corporate network. In order for your LAN to learn the routes used within your
corporate network, they should both be configured with RIP.
−
Your ISP requests that you run RIP for communication with devices on their
network..
ww
w.
Sh
o
o.i
r
−
Fields on the first setting block:
Field
Description
RIP
Enable/disable RIP feature.
Function buttons for the second setting block in this page:
Apply Changes
Click to save the setting of this setting block to the system configuration
Fields on the second setting block:
Field
Description
Interface
The name of the interface on which you want to enable RIP.
Page 42 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Receive Mode
Indicate the RIP version in which information must be passed to the DSL device in
order for it to be accepted into its routing table.
Send Mode
Indicate the RIP version this interface will use when it sends its route information to
Add
o.i
Function buttons for the second setting block in this page:
r
other devices.
Add a RIP entry and the new RIP entry will be display in the table
Delete Selected Entry
Delete a selected RIP entry. The RIP entry can be selected on the Select column of
the RIP Config Table.
ww
w.
Sh
o
4.5 Advance Configuration
4.5.1 Bridging
You can enable/disable Spanning Tree Protocol and set MAC address aging time in this
page.
Fields in this page:
Field
Description
Ageing Time
Set the Ethernet address ageing time, in seconds. After [Ageing Time] seconds of
not having seen a frame coming from a certain address, the bridge will time out
(delete) that address from Forwarding DataBase (fdb).
802.1d Spanning Tree Enable/disable the spanning tree protocol
Function buttons in this page:
Apply Changes
Page 43 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Save this bridge configuration. New configuration will take effect after saving into flash
memory and rebooting the system. See section “Admin” for details.
Show MACs
List MAC address in forwarding table.
r
4.5.2 Routing
−
o.i
The Routing page enables you to define specific route for your Internet and network data.
Most users do not need to define routes. On a typical small home or office LAN, the
existing routes that set up the default gateways for your LAN hosts and for the DSL device
provide the most appropriate path for all your Internet traffic.
On your LAN hosts, a default gateway directs all Internet traffic to the LAN port(s) on the DSL
device. Your LAN hosts know their default gateway either because you assigned it to them
when you modified your TCP/IP properties, or because you configured them to receive the
ww
w.
Sh
o
information dynamically from a server whenever they access the Internet.
−
On the DSL device itself, a default gateway is defined to direct all outbound Internet traffic to
a route at your ISP. The default gateway is assigned either automatically by your ISP
whenever the device negotiates an Internet access, or manually by user to setup through the
configuration.
You may need to define routes if your home setup includes two or more networks or
subnets, if you connect to two or more ISP services, or if you connect to a remote
corporate LAN.
Page 44 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
:
Fields in this page:
Field
Description
Enable
Check to enable the selected route or route to be added.
Destination
The network IP address of the subnet. The destination can be specified as the IP
address of a subnet or a specific host in the subnet. It can also be specified as all
zeros to indicate that this route should be used for all destinations for which no other
route is defined (this is the route that creates the default gateway).
Subnet Mask
The network mask of the destination subnet. The default gateway uses a mask of
0.0.0.0.
Next Hop
The IP address of the next hop through which traffic will flow towards the destination
subnet.
Metric
Defines the number of hops between network nodes that data packets travel. The
default value is 0, which means that the subnet is directly one hop away on the local
LAN network.
Interface
The WAN interface to which a static routing subnet is to be applied.
Page 45 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Function buttons in this page:
Add Route
Add a user-defined destination route.
Update
Update the selected destination route on the Static Route Table.
r
Delete Selected
Delete a selected destination route on the Static Route Table.
ww
w.
Sh
o
o.i
Show Routes
Click this button to view the DSL device’s routing table. The IP Route Table displays,
as shown in Figure.
Page 46 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.5.3 SNMP Configuration
ww
w.
Sh
o
o.i
r
Simple Network Management Protocol (SNMP) is a troubleshooting and management
protocol that uses the UDP protocol on port 161 to communicate between clients and
servers. The DSL device can be managed locally or remotely by SNMP protocol.
Fields in this page:
Field
Description
System Description
System description of the DSL device.
System Contact
Contact person and/or contact information for the DSL device.
System Name
An administratively assigned name for the DSL device.
System Location
The physical location of the DSL device.
System Object ID
Vendor object identifier. The vendor’s authoritative identification of the network
management subsystem contained in the entity.
Trap IP Address
Destination IP address of the SNMP trap.
Community name
Name of the read-only community. This read-only community allows read operation
(read-only)
to all objects in the MIB.
Community name
Name of the write-only community. This write-only community allows write operation
(write-only)
to the objects defines as read-writable in the MIB.
Page 47 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Function buttons in this page:
Apply Changes
Save SNMP configuration. New configuration will take effect after saving into flash
memory and rebooting the system. See section “Admin” for details.
r
4.5.4 Port Mapping
ww
w.
Sh
o
o.i
The DSL device provides multiple interface groups. Up to five interface groups are
supported including one default group. The LAN and WAN interfaces could be included.
Traffic coming from one interface of a group can only be flowed to the interfaces in the
same interface group. Thus, the DSL device can isolate traffic from group to group for
some application. By default, all the interfaces (LAN and WAN) belong to the default group,
and the other four groups are all empty. It is possible to assign any interface to any group
but only one group.
Page 48 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Fields in this page:
Field
Description
Enabled/Disabled
Radio buttons to enable/disable the interface group feature. If disabled, all interfaces
belong to the default group.
To manipulate a mapping group:
1. Select a group from the table.
r
“Interface groups
2. Select interfaces from the available/grouped interface list and add it
o.i
to the grouped/available interface list using the arrow buttons to
manipulate the required mapping of the ports.
3. Click “Apply Changes” button to save the changes.
Function buttons in this page:
ww
w.
Sh
o
Apply Changes
Save configuration to system. New configuration will take effect after saving into flash
memory and rebooting the system. See section “Admin” for details.
4.5.5 IP QoS
The DSL device provides a control mechanism that can provide different priority to different
users or data flows. The QoS is enforced by the QoS rules in the QoS table. A QoS rule
contains two configuration blocks: Traffic Classification and Action. The Traffic
Classification enables you to classify packets on the basis of various fields in the packet
and perhaps the physical ingress port. The Action enables you to assign the strictly priority
level for and mark some fields in the packet that matches the Traffic Classification rule.
You can configure any or all field as needed in these two QoS blocks for a QoS rule.
Page 49 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
Fields on the first setting block of this page:
Field
Description
IP QoS
Enable/disable the IP QoS function.
Source IP
The IP address of the traffic source.
Source Netmask
The source IP netmask. This field is required if the source IP has been entered.
Destination IP
The IP address of the traffic destination.
Destination Netmask
The destination IP netmask. This field is required if the destination IP has been
entered.
Protocol
The selections are TCP, UDP, ICMP and the blank for none. This field is required if
the source port or destination port has been entered.
Source Port
The source port of the selected protocol. You cannot configure this field without
entering the protocol first.
Destination Port
The destination port of the selected protocol. You cannot configure this field without
entering the protocol first.
Page 50 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Physical Port
The incoming ports. The selections include LAN ports, wireless port, and the blank
for not applicable.
r
Fields on the second setting block of this page:
Field
Description
Outbound Priority
The priority level for the traffic that matches this classification rule. The possible
IP Precedence
Select this field to mark the IP precedence bits in the packet that match this
classification rule.
IP Type of Service
Select this field to mark the IP TOS bits in the packet that match this classification
rule.
802.1p
o.i
selections are (in the descending priority): p0, p1, p2, p3.
Select this field to mark the 3-bit user-priority field in the 802.1p header of the packet
ww
w.
Sh
o
that match this classification rule. Note that this 802.1p marking is workable on a
given PVC channel only if the VLAN tag is enabled in this PVC channel.
4.5.6 Remote Access (Moved to ACL Config – please refer to page 57)
The Remote Access function can secure remote host access to your DSL device from LAN
and WLAN interfaces for some services provided by the DSL device.
Page 51 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Fields in this page:
Field
Description
LAN
Check/un-check the services on the LAN column to allow/un-allow the services
access from LAN side; and “WAN”:
Check/un-check the services on the WAN column to allow/un-allow the services
r
WAN
access from WAN side.
WAN Port
This field allows the user to specify the port of the corresponding service. Take the
o.i
HTTP service for example; when it is changed to 8080, the HTTP server address for
the WAN side is http://dsl_addr:8080, where the dsl_addr is the WAN side IP
address of the DSL device.
ww
w.
Sh
o
4.6 Diagnostic
The DSL device supports some useful diagnostic tools.
Fields in this page:
4.6.1 Diagnostic Test
The Diagnostic Test page shows the test results for the connectivity of the physical layer
and protocol layer for both LAN and WAN sides.
Page 52 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
o.i
r
User Manual
Fields in this page:
Field
Description
Select the Internet
The available WAN side interfaces are listed. You have to select one for the WAN
Connection
side diagnostic.
4.7 Admin
4.7.1 Save & Reboot
Page 53 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
ww
w.
Sh
o
Function buttons in this page:
o.i
r
User Manual
1. Save Current Configuration >> Apply
2. Factory Default Configuration >> Apply
3. Reboot >> restart the modem
4.7.2 Backup/Restore
This page allows you to backup and restore your configuration into and from file in your
host.
Page 54 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.7.3 System Log
ww
w.
Sh
o
o.i
r
This page shows the system log.
4.7.4 Password
The first time you log into the system, you use the default password. There are two-level
logins: admin and user. The admin and user password configuration allows you to
change the password for administrator and user.
Page 55 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
o.i
r
User Manual
ww
w.
Sh
o
Fields in this page:
Field
Description
User Name
Selection of user levels are: admin and user.
Old Password
Enter the old password for this selected login.
New Password
Enter the new password here.
Confirmed Password
Enter the new password here again to confirm.
4.7.5 Upgrade Firmware
To upgrade the firmware for the DSL device:
−
Click the Browse button to select the firmware file.
−
Confirm your selection.
−
Click the Upload button to start upgrading.
IMPORTANT! Do not turn off your DSL device or press the Reset button while this procedure is in progress.
Page 56 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.7.6 ACL
ww
w.
Sh
o
o.i
r
The Access Control List (ACL) is a list of permissions attached to the DSL device. The list
specifies who is allowed to access this device. If ACL is enabled, all hosts cannot access
this device except for the hosts with IP address in the ACL table.
1. LAN – You can enable LAN ACS Switch to allow/block the PC to access the Modem
2. WAN – you can enable web(http)/telenet/ftp/tftp/snmp/ping for WAN access
Page 57 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.7.7 Time Zone
ww
w.
Sh
o
o.i
r
Simple Network Timing Protocol (SNTP) is a protocol used to synchronize the system time
to the public SNTP servers. The DSL device supports SNTP client functionality in
compliance with IETF RFC2030. SNTP client functioning in daemon mode which issues
sending client requests to the configured SNTP server addresses periodically can
configure the system clock in the DSL device
Fields in this page:
Field
Description
Current Time
The current time of the specified time zone. You can set the current time by yourself
or configured by SNTP.
Time Zone Select
The time zone in which the DSL device resides.
Enable SNTP client
Enable the SNTP client to update the system clock.
update
SNTP server
The IP address or the host name of the SNTP server. You can select from the list or
set it manually.
Page 58 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.7.8 TR-069 Config (Optional)
ww
w.
Sh
o
o.i
r
TR-069 is a protocol for communication between a CPE and Auto-Configuration Server
(ACS). The CPE TR-069 configuration should be well defined to be able to communicate
with the remote ACS.
Fields in this page:
ACS Field
Description
URL
ACS URL. For example, http://10.0.0.1:80 https://10.0.0.1:443
User Name
The username the DSL device should use when connecting to the ACS.
Password
The password the DSL device should use when connecting to the ACS.
Periodic Inform Enable When this field is enabled, the DSL device will send an Inform RPC to the ACS
Page 59 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
server at the system startup, and will continue to send it periodically at an interval
defined in Periodic Inform Interval field; When this field is disabled, the DSL device
will only send Inform RPC to the ACS server once at the system startup.
Periodic Inform Interval Time interval in second to send Inform RPC.
Description
r
Connection Request
Field
The username the remote ACS should use when connecting to this device.
Password
The password the remote ACS should use when connecting to this device.
Path
The path of the device ConnectionRequestURL. The device
o.i
User Name
ConnectionRequestURL should be configured based on the Device_IP, Path and
Port as follows:
http://Device_IP:Port/Path
The port of the device ConnectionRequestURL.
ww
w.
Sh
o
Port
Page 60 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.8 Statistics
The DSL device shows the different layer of network statistics information.
4.8.1 Interfaces
ww
w.
Sh
o
o.i
r
You can view statistics on the processing of IP packets on the networking interfaces. You
will not typically need to view this data, but you may find it helpful when working with your
ISP to diagnose network and Internet data transmission problems.
To display updated statistics showing any new data since you opened this page, click
Refresh.
Page 61 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
4.8.2 ADSL
ww
w.
Sh
o
o.i
r
This page shows the ADSL line statistic information.
Page 62 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
5 Channel Mode Configuration
5.1 Bridge Mode
ww
w.
Sh
o
o.i
ADSL modem/router can be set to Bridge mode.
r
ADSL router supports multiple channel operation modes. This section will show
procedures to configure the router.
1. Open the WEB page at “WAN interface/Channel Configuration”.
2. Select your VPI/VCI under ATM VC table
3. Change the Channel Mode to “1483 Bridged”. Set the parameters VPI/VCI and
Encapsulation mode according to the CO DSLAM’s setting.
4. Click “Add” button to add this channel into VC table.
5. Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
6. The new settings will take effect after reboot the system.
Page 63 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
5.2 MER(Mac Encapsulating Routing) Mode
1. Open the WEB page at “WAN interface/Channel Configuration”.
2. Select the Channel Mode to “1483 MER”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
3. Set “Local IP Address:” according to the IP that ISP assign for your router. Set “Remote IP
Address” to the ISP’s gateway.
4. Click “Add” button to add this channel into VC table.
5. Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
6. The new settings will take effect after reboot the system.
Page 64 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
5.3 PPPoE Mode
1. Open the WEB page at “WAN interface/Channel Configuration”.
2. Select the Channel Mode to “PPPoE”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
3. Enter user/password from your ISP.
4. Click “Add” button to add this channel.
5. Enable DHCP server to allow the local PCs share the PPP connection. Reference to section
4.6.1 DHCP Server Configuration.
6. Set DNS address from your ISP. Reference to section 4.6.2 DNS Configuration.
7. Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
8. The new settings will take effect after reboot the system.
Page 65 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
5.4 PPPoA Mode
1. Open the WEB page at “WAN interface/Channel Configuration”.
2. Select the Channel Mode to “PPPoA”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
3. Enter user/password from your ISP.
4. Click “Add” button to add this channel.
5. Enable DHCP server to allow the local PCs share the PPP connection. Reference to section
4.6.1 DHCP Server Configuration.
6. Set DNS address from your ISP. Reference to section 4.6.2 DNS Configuration.
7. Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
8. The new settings will take effect after reboot the system.
Page 66 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
ww
w.
Sh
o
o.i
r
5.5 1483 Routed Mode
1. Open the WEB page at “WAN interface/Channel Configuration”.
2. Select the Channel Mode to “1483 Routed”. Set the parameters VPI/VCI and
Encapsulation mode according to the CO DSLAM’s setting.
3. In WAN IP settings, give the local and remote IP address from your ISP or use DHCP to
get them automatically if your ISP support it. Local IP is the address of ADSL router.
Remote IP is the ISP’s gateway address.
4. Click “Add” button to add this channel.
5. Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
6. The new settings will take effect after reboot the system.
Page 67 of 73
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Appendices
Appendix A: Protocol Stacks
IP
IP
Ethernet
Ethernet
Ethernet
ww
w.
Sh
o
Ethernet
o.i
r
5.5.1 A.1 1483 Bridged Model
LLC/SNAP
(1483-B)
LLC/SNAP
(1483-B)
AAL5
AAL5
SAR
SAR
ATM
100BaseT
PC
100BaseT
xDSL
ATU-R
xDSL
ATM
ATM
SONET/SDH
SONET/SDH
DSLAM
1483 Bridged Channel Mode Scenario
Page 68 of 73
BRAS
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
IP
IP
Ethernet
Ethernet
Ethernet
LLC/SNAP
(1483-B)
AAL5
Ethernet
LLC/SNAP
(1483-B)
AAL5
SAR
ww
w.
Sh
o
SAR
IP
o.i
IP
r
5.5.2 A.2 1483 MER Model
ATM
100BaseT
PC
100BaseT
xDSL
ATU-R
xDSL
ATM
ATM
SONET/SDH
SONET/SDH
DSLAM
1483 MER Channel Mode Scenario
Page 69 of 73
BRAS
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
IP
IP
r
5.5.3 A.3 PPPoE Model
IP
IP
PPPoE
Ethernet
Ethernet
Ethernet
LLC/SNAP
(1483-B)
AAL5
SAR
PPPoE
Ethernet
LLC/SNAP
(1483-B)
AAL5
SAR
ATM
ATM
SONET/SDH
SONET/SDH
ww
w.
Sh
o
ATM
PPP
o.i
PPP
100BaseT
PC
100BaseT
xDSL
ATU-R
xDSL
DSLAM
PPPoE Channel Mode Scenario
Page 70 of 73
BRAS
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
IP
IP
IP
Ethernet
Ethernet
PPP
AAL5
IP
PPP
AAL5
SAR
ww
w.
Sh
o
SAR
o.i
r
5.5.4 A.4 PPPoA Model
ATM
100BaseT
PC
100BaseT
xDSL
ATU-R
xDSL
ATM
ATM
SONET/SDH
SONET/SDH
DSLAM
PPPoA Channel Mode Scenario
Page 71 of 73
BRAS
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
IP
IP
Ethernet
Ethernet
IP
LLC/SNAP
(1483-R)
AAL5
IP
LLC/SNAP
(1483-R)
AAL5
SAR
ww
w.
Sh
o
SAR
o.i
r
5.5.5 A.5 1483 Routed Model
ATM
100BaseT
PC
100BaseT
xDSL
ATU-R
xDSL
ATM
ATM
SONET/SDH
SONET/SDH
DSLAM
1483 Routed Channel Mode Scenerio
Page 72 of 73
BRAS
PROLiNK Hurricane 5301G
Wireless ADSL2+ Modem / Router
User Manual
Appendix
PRODUCT SUPPORT AND CONTACT INFORMATION
Singapore Service Center
Tel: (65) 6357 0668
Fax: (65) 6357 0669
Email: support@fida.com
o.i
r
At PROLiNK, we are committed to provide you with the best quality of products as well as
the best technical support. While if your computer is infected by virus, we may suggest you
to find a solution in order to remove the virus, because we are unable to assist you until the
virus is eradicated.
ww
w.
Sh
o
Address: Blk 16 Kallang Place, #06-02 Kallang Basin Industrial Estate, Singapore 339156.
Operating Hours: Mon-Fri : 0900-1745 hrs Wed : 0900-2030 hrs
Malaysia Service Center
Tel: (603) 8023 9151
Fax: (603) 8024 9161
Email: support_my@fida.com
Address: 29, Jalan USJ 1/31, 47600 Subang Jaya, Selangor Darul Ehsan. Malaysia
Operating Hours: Mon-Fri: 0900-1745 hrs Sat: 0900-1300 hrs
Indonesia Service Center
Tel: (62) 021 628 3205
Fax: (62) 021 628 3206
Email: support_id@fida.com
Address: P. Jayakarta Komplek 85 BR/AJ Jakarta Pusat – Indonesia
Operating Hours: Mon-Fri: 0900-1800 hrs
www.prolink2u.com
© Copyright 2008 Fida International (S) Pte Ltd.
Windows 2000, Windows XP and Windows Vista are registered Trademarks of Microsoft Corporation.
Page 73 of 73
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising