PEB-7604VG3A User`s Manual R1.1

Add to my manuals
50 Pages

advertisement

PEB-7604VG3A User`s Manual R1.1 | Manualzz

PEB-7604VG3A

Intel

®

Pentium

®

M

915GM Mini ITX

User’s Manual

Rev. 1.1

2006/12/25

PEB-7604VG3A User’s Manual

Copyright

All rights reserved. The information contained in this guide has been validated and reviewed for accuracy. No patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, the Manufacturer assumes no responsibility for errors or omissions.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Manufacturer.

Trademark

Intel

®

, Pentium

®

and Celeron

®

are registered trademarks of Intel

®

Corporation.

Microsoft

®

and Windows

®

are registered trademarks of Microsoft Corporation.

All products and company names are trademarks or registered trademarks of their respective holders.

These specifications are subject to change without notice.

Technical Support

We hope you to get the maximum performance from your products and be willing to help if running into technical difficulties. For the most frequently asked questions, it’s easily found answers from the product documentation and usually a lot more detailed, so please take reference to this manual first. If the answer still can not be found, gather all the information or questions applying to the problem, and with the product on hand, contact your distributor, sales representative, or customer service center for technical support. Most problems reported are minor and able to be easily solved over the phone. In addition, free technical support is available and always ready to give advices on application requirements or specific information on the installation and operation of any of our products.

Please have the following information ready before you call:

1. Product name and serial number

2. Description of your peripheral attachments

3. Description of your software (operating system, version, application software, etc.)

4. A complete description of the problem

5. The exact wording of any error messages

2 / 50

How to Use This Manual

PEB-7604VG3A User’s Manual

This manual is written for the system integrator, PC technician and knowledgeable PC end user. It describes how to configure your PEB-7604VG3A to meet various operating requirements. The user’s manual is divided into four chapters, with each chapter addressing a basic concept and operation of the server board.

Chapter 1: Introduction - presents what you have inside the box and gives you an overview of the product specifications and basic system architecture for the

PEB-7604VG3A server board.

Chapter 2: Hardware Configuration Setting - shows the definitions and locations of

Jumpers and Connectors so that you can easily configure your system.

Chapter 3: System Installation - describes how to properly mount the CPU, main memory, and M-System Flash disk for a safe installation. It will also introduce and show you the driver installation procedure for the Graphics Controller and Ethernet Controller.

Chapter 4: BIOS Setup Information - specifies the meaning of each setup parameter, how to get advanced BIOS performance and update to a new BIOS.

Note:

(1) Memory type support dual-channel interleaved mode assuming DDR2 533 MHz, all DIMMs in a system must be of the same type, the speed in all channels is the speed of the slowest DIMM in the system.

3 / 50

PEB-7604VG3A User’s Manual

Table of Content

1.

Introduction.................................................................................................................8

1.1

1.2

1.3

1.4

1.5

Description...........................................................................................................8

Packing Check List..............................................................................................9

Specifications ....................................................................................................10

System Architecture..........................................................................................12

Dimensions ........................................................................................................13

2.

Hardware Configuration Setting..............................................................................15

2.1

2.2

2.3

Board Layout .....................................................................................................15

Jumpers & Connectors .....................................................................................16

Jumpers/Connectors Setting............................................................................17

2.3.1 RTC CMOS Clear Select (JP1) ....................................................................17

2.3.2 CPU Frequency Select (JP4) .......................................................................17

2.3.3 Internal Audio for Chassis (AUDIO1) ............................................................17

2.3.4 Audio Connector (AUDIO2) ..........................................................................17

2.3.5 CD-In from CD-ROM (CD1)..........................................................................17

2.3.6 Chassis/CPU/System Connectors (CHS_FAN1, CPU_FAN1, SYS_FAN1)..17

2.3.7 COM1 / VGA & COM2 Connector (COM2, VGA_COM1) .............................17

2.3.8 DVI Connector (DVI......................................................................................18

2.3.9 GPIO Connector (GPIO1).............................................................................18

2.3.10 IrDA Connector (IR1) ....................................................................................18

2.3.11 PS/2 Keyboard & Mouse (KBMS1)...............................................................19

2.3.12 LAN LED Connector (LAN_LED1)................................................................19

2.3.13 LAN 1/2/3 & USB 1/2 Connectors (LAN2_LAN3, USB1LAN1) .....................19

2.3.14 LCD Inverter Connector (LVDS1) .................................................................19

2.3.15 LVDS Connector (LVDS2) ............................................................................20

2.3.16 Front Side Indicators (PANEL1) ...................................................................20

2.3.17 24-pin ATX Power Connector (PWR1)..........................................................20

2.3.18 Serial ATA 1/2 Connectors (SATA1, SATA2) .................................................21

2.3.19 Internal Speaker Connector (SPK1) .............................................................21

2.3.20 Internal USB 3/4/5/6 Connectors (USB2, USB3)..........................................21

4 / 50

PEB-7604VG3A User’s Manual

3.

System Installation ...................................................................................................23

3.1 Socket 478 Processors .....................................................................................23

3.1.1 Installing Intel

®

Pentium

®

M / Celeron

®

M CPU ............................................23

3.2 Installing Cooling Fan .......................................................................................23

3.3

3.4

Main Memory......................................................................................................24

Installing the Mini-ITX........................................................................................25

3.4.1 Intel 915GM Integrated Graphics Controller .................................................25

3.4.2 Triple Marvell Gigabit Ethernet Controller.....................................................26

3.4.3 Drivers Support ............................................................................................26

4.

BIOS Setup................................................................................................................28

4.1

4.2

Entering Setup ...................................................................................................28

Main Menu ..........................................................................................................28

4.2.1 Standard CMOS Features ............................................................................29

4.2.2 Advanced BIOS Features.............................................................................30

4.2.3 Advanced Chipset Features .........................................................................34

4.2.4 Integrated Peripheral ....................................................................................37

4.2.5 Power Management Setup ...........................................................................41

4.2.6 PnP/PCI Configurations ...............................................................................43

4.2.7 PC Health Status ..........................................................................................45

4.2.8 Frequency/Voltage Control ...........................................................................46

4.2.9 Load Fail-Safe Default..................................................................................46

4.2.10 Load Optimized Defaults ..............................................................................47

4.2.11 Supervisor/User Password Setting ...............................................................47

4.2.12 Exit Selection................................................................................................49

5 / 50

PEB-7604VG3A User’s Manual

Revision History

Revision Date By

Rev.1.0 Nov. 2006 ChunFu, Tai Initial released

Rev.1.1 Dec. 2006 ChunFu, Tai JP4 inserted

Comment

6 / 50

PEB-7604VG3A User’s Manual

CHAPTER 1

7 / 50

PEB-7604VG3A User’s Manual

1. Introduction

1.1 Description

The PEB-7604VG3A series all-in-one Mini ITX is designed to fit a high performance

Pentium M based processor and compatible for high-end computer system application with

PCI bus architecture. It is made to meet today’s demanding pace, and keep complete compatibility with hardware and software designed for the IBM PC/AT. The on-board devices support one PCI slot, integrated graphics, and on-board three Marvell Gigabit

Ethernet controllers. It’s beneficial to build up a high performance and high data availability system for VARs, or system integrators.

PEB-7604VG3A series support the following processors:

Intel ® uFC-PGA 478 Pentium M® / Celeron M processor FSB 400/533 MH with 0.90 and 0.13 micron technology.

This Mini ITX can run with Intel Socket 479 Pentium/Celeron M processors and support

DIMM up to 2 GB dual-channel DDR2 533 memory. The enhanced on-board one PCI-IDE interface can support 1 drive up to PIO mode 4 timing and Ultra ATA 33/66/100 synchronous mode feature, one CF socket interface, and 2 Serial ATA high-speed data transfers at up to 150 MB/s connectors. The on-board Super I/O chipset supports two serial ports, one SIR (Serial Infrared) port, two high performance 16C550-compatible UARTs provide 16-byte send/receive FIFOs, and two RS-232 serial port interfaces. Besides, H/W monitor function, Intel High Definition Audio as 5.1 surround sound, six Hi-Speed USB 2.0 ports offering up to 40X greater bandwidth over USB 1.1. Also provide dual display function by VGA and DVI, by VGA, and LVDS interface.

The Mini-ITX standard makes the PEB-7604VG3A series work with the one slot PCI and one 6-pin Mini-DIN connector for PS/2 mouse and keyboard. The on-board Flash ROM is used to make the BIOS update easier. The high precision Real Time Clock/calendar is built to support Y2K for accurate scheduling and storing configuration information. One 20-pin standard connector is designed to support ATX power function. A feature of CPU overheat protection will give user more security and stability. All of these features make

PEB-7604VG3A series excellent in stand-alone applications.

Note: 1) The PEB-7604VG3A series only support Intel Pentium/Celeron M processor (Dothan 400/533 FSB) for 0.13 and 0.90 micron.

2) The PEB-7604VG3A series only support DDR2 533 memory module.

8 / 50

PEB-7604VG3A User’s Manual

1.2 Packing Check List

The PEB-7604VG3A Series package includes the following basic items accompany with this manual.

One PEB-7604VG3A series Mini ITX

One Quick Installation Guide for PEB-7604VG3A

One 40-pin IDE cable

One Serial ATA cable

One Serial port cable for COM2

One optional USB 2.0 cable

One Supporting CD-ROM contains User’s Manual and internal VGA display driver and Marvell Gigabit Ethernet network controller driver and on board devices drivers

If any of these items is damaged or missed, please contact your vendor and save all packing materials for future replacement and maintenance.

9 / 50

1.3 Specifications

System

CPU

FSB

BIOS

System Chipset

I/O Chip

System Memory

Storage

SSD

Watchdog Timer

H/W Status Monitor

PEB-7604VG3A User’s Manual

Supports Intel µFC-PGA 478 Pentium® M / Celeron® M Processor with

65nm / 90nm process technology, up to 2.26G / 2.0G

FSB 533/400 MHz

Award BIOS with 4 Mb Flash ROM

Intel

®

915GM + ICH6M

Winbond W83627THG-AW supports two serial ports

2 x 240-pin DIMM sockets support dual channel DDR2 from 128 MB to 2

GB at 400/533 MHz memory bus

1 x Ultra DMA100/66/33 support two IDE devices by 40-Pin IDE connector ; 2 x Serial ATA connectors high-speed data transfer at up to

150 MB/s

1 x CompactFlash Type I/II Socket

Reset: 1 sec.~255 min. and 1 sec. or 1 min./step

Monitoring system temperature, voltage, and cooling fan status.

Auto throttling control when CPU overheats.

System automatically restored on recovery of AC power loss.

Built-in ICH6M with Y2K compliant

On-board programmable 8-bit Digital I/O interface

1 x 32-bit PCI slot compliant with PCI v2.3 specification

Real Time Clock

GPIO

Expansion

MIO

Internal

External

Display

Chipset

Display Memory

1 x RS-232, 4 x USB 2.0

1 x RS-232, 1 x K/B, 1 x Mouse, 3 x LAN & 2 x USB 2.0

Resolution

VGA/LCD Interface

LVDS

DVI

Intel® 915GM Integrated Intel® GMA 900 graphics

Intel® DVMT 3.0 supports up to 128 MB video memory

CRT mode: support maximum resolution up to 2048 x 1536 at fresh rate

75Hz (QXGA)

Multiple maximum overlay display resolution up to 1600x1200 at 85 Hz

(UXGA)

DSUB-15 VGA connector for DAC output

Dual Channel 18-bit LVDS

Chrontel CH7307 DVI transmitter

10 / 50

Audio

Chipset

AC97 Codec

Audio Interface

Ethernet

Chipset

Ethernet Interface

Mechanical & Environmental

PEB-7604VG3A User’s Manual

Intel

®

ICH6M

Realtek ALC655 AC97 5.1 CH 3D audio interface

Mic in, Line in, CD Audio in, Line out, Rear out and Center/Subwoofer out

Three Marvell

®

Yukon

TM

-EC 88E8053 PCI Express

TM

Ethernet controllers

IEEE 802.3 10/100/1000BASE-T Gigabit Ethernet compliant

Power Requirement

Power Type

Operating Temperature

Operating Humidity

Size (L x W)

Weight

3.3 V @ 3.4 A, +5 V @ 359 mA, +12 V @ 1,92 A , -12 V @ 294 mA, 5 Vsb

@ 263 mA

ATX

0~60°C (32~140°F)

0%~90% relative humidity, non-condensing

6.69" x 6.69" (170 mm x 170 mm)

0.94 lbs (0.43 Kg)

11 / 50

PEB-7604VG3A User’s Manual

All of details operating relations are shown in PEB-7604VG3A series system block diagram.

12 / 50

1.5 Dimensions

PEB-7604VG3A User’s Manual

13 / 50

Unit: mm

PEB-7604VG3A User’s Manual

CHAPTER 2

14 / 50

2. Hardware Configuration Setting

PEB-7604VG3A User’s Manual

This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on PEB-7604VG3A SERIES are in the proper position. The default settings shipped from factory are marked with an asterisk ( ).

In general, jumpers on the Mini ITX are used to select options for certain features. Some of the jumpers are designed to be user-configurable, allowing for system enhancement. The others are for testing purpose only and should not be altered. To select any option, cover the jumper cap over (SHORT) or remove (NC) it from the jumper pins according to the following instructions. Here, NC stands for “Not Connect”.

15 / 50

PEB-7604VG3A User’s Manual

2.2 Jumpers & Connectors

JUMPERS

JP1

JP4

FUNCTION

RTC CMOS clear select

CPU frequency select

CONNECTORS FUNCTION

AUDIO1

AUDIO2

CD1

Internal audio for chassis

Audio connector

CD-In from CD-ROM

CF1

CHS_FAN1

Compact Flash card connector

Chassis fan connector

CPU_FAN1

COM2

CPU fan connector

Serial port 2 connector

DIMM1, DIMM2 240-pin DDR2 SDRAM 1 & 2 socket

DVI1

DVI connector

GPIO1

IDE1

GPIO connector

Primary IDE connector

IR1

IrDA connector

KBMS1

LAN_LED1

PS/2 keyboard & mouse connector

LAN LED connector

LAN2_LAN3

LAN 2 & LAN 3 connectors

LVDS1

LVDS2

PANEL1

LCD inverter connector

LVDS connector

Front side indicators:

IDE1 active LED (1-3)

System power on LED (2-4)

System reset LED (5-7)

System power on switch LED (6-8)

PCI1

PWR1

PCI slot

24-pin ATX power connector

SATA1, SATA2 Serial ATA 1 & 2 connector

SPK1

Internal speaker connector

SYS_FAN1

System fan connector

USB1LAN1

USB 1, 2 & LAN 1 connectors

USB2, USB3

Internal USB 3, 4 & 5, 6 connectors

VGA_COM1

D-sub 15-pin VGA & D-sub 9-pin serial port 1 connectors

REMARK

2 x 1 header

2 x 1 header

REMARK

2 x 5 header

Audio jack x 3

1 x 4 header

2 x 5 header

HIROSE

2 x 5 header

2 x 20 header

2 x 3 header

2 x 6 header

HIROSE

2 x 5 header

1 x 4 header

2 x 5 header

16 / 50

PEB-7604VG3A User’s Manual

2.3.1 RTC CMOS Clear Select (JP1)

OPEN SHORT

2.3.2 CPU Frequency Select (JP4)

OPEN SHORT

Normal Operation Clear CMOS contents

400 MHz 533 MHz

2.3.3 Internal Audio for Chassis (AUDIO1) 2.3.4 Audio Connector (AUDIO2)

PIN No.

1

Description

F_MIC1

PIN No.

1 (Blue)

Description

Line-in

Speaker out

MIC-in

3 F_MIC2

4 +5V

3 (Red)

5 LOUTR

6 F_R

7 NC

8 NC

9 LOUTL

10 F_L

2.3.5 CD-In from CD-ROM (CD1) 2.3.6 Chassis/CPU/System Connectors

(CHS_FAN1, CPU_FAN1, SYS_FAN1)

PIN No. Description PIN No.

1

Description

CD-L

2 CD-Ground

3 CD-Ground

4 CD-R

1 GND

2 +12V

3

4

SENSE

Control (CPU_FAN1 only)

2.3.7 COM1 / VGA & COM2 Connector (COM2, VGA_COM1)

COM1 / COM2

PIN No.

1

Description

Data Carrier Detect

VGA

Description PIN No. PIN No. Description

Green Signal 2 1 Red Signal

3

5

6

7

9

Transmit Data

Ground

Data Set Ready

Request To Send

Ring Indicator

Ground 6 5 Ground

Ground 8 7 Ground

Ground 10 9 +5V

DCC_DATA 12 11 NC

VSYNC 14 13 HSYNC

17 / 50

2.3.8 DVI Connector (DVI

Description PIN No. PIN No. Description

TDC0# 2 1 +5V

TDC0 4 3 GND

NC 6 5 NC

TDC1#

NC

10

14

9

13

HPDET

MDVICLK

PEB-7604VG3A User’s Manual

TDC2# 18 17 TLC#

Signal

TDC0,TDC0#

TDC1,TDC1#

TDC2,TDC2#

HPDET

TMDSDATA

TMDSDCLK

TLC,TLC#

Type

O

O

O

I

I/O

I/O

O

Description

DVI Data Channel 0 Output: These pins provide the DVI differential output for data channel 0 (Blue).

DVI Data Channel 1 Output: These pins provide the DVI differential output for data channel 1 (Green).

DVI Data Channel 2 Output: These pins provide the DVI differential output for data channel 2 (Red).

Hot Plug Detect (internal pull-down): This input determines whether the

DVI is connected to a DVI monitor. When terminated , the monitor is required to apply a voltage greater than 2.4 volts. Changes on the status of this pin will be relayed to the graphics controller via the P-OUT/TLDET* or

GPIO(1)/TLDET* pin pulling low.

DVI I2C Data: This signal is used as the I2C DOC clock for a digital display connector (i.e. TV-Out Encoder , TMDS transmitter ). This signal is tri-stated during a hard reset.

DVI DOC Clock: This signal is used as the DOC clock for a digital display connector (i.e. primary digital monitor). This signal is tri-stated during a hard reset.

DVI Clock Output: These pins provide the differential clock outputs to the

DVI interface corresponding a data on TDC(0:2) outputs.

2.3.9 GPIO Connector (GPIO1)

PIN No. Description

1

2

3

4

5

+3.3V

General Purpose I/O bit 3

General Purpose I/O bit 5

General Purpose I/O bit 0

General Purpose I/O bit 7

6

7

8

9

General Purpose I/O bit 2

General Purpose I/O bit 4

General Purpose I/O bit 1

General Purpose I/O bit 6

10 Ground

2.3.10 IrDA Connector (IR1)

PIN No.

1

Description

NC

2 NC

3

4

+5V

Infrared transmitter output

5

6

Ground

Infrared receiver input

18 / 50

PEB-7604VG3A User’s Manual

2.3.11 PS/2 Keyboard & Mouse (KBMS1) 2.3.12 LAN LED Connector (LAN_LED1)

PIN No.

1

Description

Keyboard Data

PIN No.

1

Description

L1_LED_LINKACT

3 Ground

4 +5V

5 Keyboard Clock

2 L1_LED_LINK100

3 L1_LED_LINKACT_V

4 L1_LED_LINK1000

5 L2_LED_LINKACT

6 L2_LED_LINK100

7 L2_LED_LINKACT_V

8 L2_LED_LINK1000

9 L3_LED_LINKACT

10 L3_LED_LINK100

11 L3_LED_LINKACT_V

12 L3_LED_LINK1000

2.3.13 LAN 1/2/3 & USB 1/2 Connectors (LAN2_LAN3, USB1LAN1)

LAN 1/2/3 USB 1/2

PIN No.

1

Description

TX+

PIN No.

5

Description

NC

2 TX- 6 RX-

3 RX+ 7 NC

PIN No. Description PIN No. Description

1 +5 V (fused) 5 +5 V (fused)

2 USBP0- 6 USBP1-

3 USBP0+ 7 USBP1+

4 Ground 8 Ground

4 NC 8 NC

2.3.14 LCD Inverter Connector (LVDS1)

PIN No.

1

Description

+12V

2 Ground

3 Backlight On/Off control

4 Backlight brightness adjustment

5 +5V

19 / 50

2.3.15 LVDS Connector (LVDS2)

Description PIN No. PIN No. Description

+5V 2 1 +3.3V

Ground 6 5 Ground

LCTLB_CLK_L 8 7 LDDC_CLKL

LCTLB_DATA_L 10 9 LDDC_DATA_L

Ground 12 11 Ground

Ground 14 13 Ground

A_CLK- 16 15 B_CLK-

A_CLK+ 18 17 B_CLK+

Ground 20 19 Ground

A_DATA0- 22 21 B_DATA0-

A_DATA0+ 24 23 B_DATA0+

Ground 26 25 Ground

A_DATA1- 28 27 B_DATA1-

A_DATAP+ 30 29 B_DATA1+

Ground 32 31 Ground

A_DATA2- 34 33 B_DATA2-

A_DATA2+ 36 35 B_DATA2+

Ground 38 37 Ground

+12V 40 39 +12V

PEB-7604VG3A User’s Manual

Signal

LCTLB_CLK_L

LCTLB_DATAL

Type

I/O

I/O

Description

I

2

C Based control signal (Clock) for External SSC clock chip control

I

2

C Based control signal (Data) for External SSC clock chip control

LDDC_CLKL I/O EDID support for flat panel display

LDDC_DATAL I/O EDID support for flat panel display

2.3.16 Front Side Indicators (PANEL1)

IDE1 Active LED

2.3.17 24-pin ATX Power Connector (PWR1)

Description PIN No. PIN No. Description

+3.3V 13 1 +3.3V

PIN No. Signal Description

1 +5V (Pull-up for HDD LED)

3 HDD active# (LED cathode terminal)

Ground 15 3 Ground

PS_ON 16 4 +5V

PIN No.

5

System Reset LED

Signal Description

Reset

Ground

7 Ground

Ground

17

Ground 18 6 +5V

19

5

7

Ground

Ground

System Power On Switch LED

+5V 21 9 5VSB

PIN No.

6

Signal Description

Power button control signal

8 Ground

+5V 23 11 +12V

Ground 24 12 +3.3V

20 / 50

PEB-7604VG3A User’s Manual

2.3.18 Serial ATA 1/2 Connectors (SATA1,

SATA2)

These SATA connectors support Serial ATA 150. Each

SATA connector can only support one serial ATA device.

Note: With most storage devices, there is a power cable that you need attach to a power source (power supply).

2.3.19 Internal Speaker Connector (SPK1)

PIN No.

1

Description

Ground

2 Ground

3 NC

4 +5V

2.3.20 Internal USB 3/4/5/6 Connectors (USB2, USB3)

PIN No. Description

Note :

1 5VSB

1) This mainboard provides 2 USB headers on the board

2 5VSB allowing for 4 additional USB ports. To make use of

3 DATA_3- / DATA_5-

4 D ATA_3- / DATA_5+ these headers, you must attach a USB bracket/cable

5 DATA_4+ / DATA_6- with USB ports (some models will come packaged with

6 D ATA_4+ / DATA_6+ a USB 4-port bracket-cable). The optionally packaged

7 Ground

8 Ground bracket will have two connectors that you can connect to the headers (USB1, USB2). The other end (bracket

9 NC

10 NC containing the USB ports) is attached to the computer casing.

2)

If you are using a USB 2.0 device with Windows

2000/XP, you will need to install the USB 2.0 driver from the Microsoft® website. If you are using Service pack 1 (or later) for Windows® XP, and using Service pack4 (or later) for Windows® 2000, you will not have to install the driver.

21 / 50

PEB-7604VG3A User’s Manual

CHAPTER 3

22 / 50

PEB-7604VG3A User’s Manual

This chapter provides you with instructions on how to setup your system. The additional information shows you how to install CPU/ FAN and memory.

3.1 Socket 478 Processors

Intel

®

Pentium

®

M / Celeron

®

M CPU

The processor socket comes with a screw to secure the processor, please unlock the screw first.

Position the CPU above the socket and the gold triangular mark on the CPU must align with pin 1 of the CPU socket. Then Insert the CPU gently seated in place.

Turn the screw to the lock position.

Unlock

Lock

Pin 1 of the socket

Gold triangular mark

Note: Do not force the CPU into the socket. It may bend the pins and damage the

CPU.

3.2 Installing Cooling Fan

Warning For a safety landing, avoid leaving prongs on hard surface.

Instructions:Smear thermal grease on the top of the CPU. Lower the CPU fan onto the CPU/CPU socket and secure it using the attachments or screws provided on the fan. Finally, attach the fan power cable to the CPUFAN adapter. For more details on this, go to http://www.intel.com

23 / 50

PEB-7604VG3A User’s Manual

PEB-7604VG3A series provide 2 DIMMs (240-pin Dual In-line Memory Module) to support

1.5V DDRAM (Synchronized DRAM) as on-board main memory. The maximum memory size is 256 MB ~ 2 GB with using 256MB/512MB/1GB technology. Supports up to 2 double sided DIMMs at DDR2 533MHz. The memory architecture adopts 128-bit data interface to support for x8 and x16 DDRAM(DDR2) device width. In addition, it only supports Non-ECC memory.

For system compatibility and stability, don’t use memory module without brand. You can also use the single or double-side DIMM .The three DIMMs can be out of order. You can install different size of DDRAM module on DIMM1, DIMM2 or all to boot up system.

Without out the contact and lock integrity of memory module with socket, it will impact on the system reliability. Follow normal procedure to install your DDRAM module into memory socket. Before locking, make sure that the module has been fully inserted into the DIMM slot.

NOTE: For maintaining system stability, do not change any of DDR2 memory parameters in

BIOS setup to upgrade your system performance without acquiring technical information.

24 / 50

PEB-7604VG3A User’s Manual

3.4 Installing the Mini-ITX

To install your PEB-7604VG3A series into standard chassis or proprietary environment, you need to perform the following steps:

1. Check all jumpers setting on proper position

2. Install and configure CPU and memory module on right position

3. Place PEB-7604VG3A series into the dedicated position in your system

4. Attach cables to existing peripheral devices and secure it

NOTE: Please refer section 3.4 to install display and Ethernet drivers and setup your system.

WARNING: Please ensure that your SBC properly inserted and fixed by mechanism.

Otherwise, the system might be unstable or do not work from bad contact of golden finger.

3.4.1 Intel 915GM Integrated Graphics Controller

The on-board graphics controller integrated in 915GM(GMCH) chipset that integrates high performance memory technology , the on-board operates at a frequency of 2.5Gb/s on each lane while employing 8b/10b encoding, and supports a maximum theoretical bandwidth of 4Gb/s each direction, the 82915GM GMCH multiplexes the PCI Express interface with DVI & CRT support. The chipset supports the following modes.

Bits Per Pixel (frequency in Hz)

Resolution

256 Color 16-bit 32-bit

640x480 60,70,72,75,85,100,120 60,70,72,75,85,100,120 60,70,72,75,85,100,120

800x600 60,70,72,75,85,100,120 60,70,72,75,85,100,120 60,70,72,75,85,100,120

1024x768 60,70,72,75,85,100,120 60,70,72,75,85,100,120 60,70,72,75,85,100,120

1152x864 60,75,85,100 60,75,85,100 60,75,85,100

1280x600 60 60 60

1280x720 60,75,85,100

1280x768 60,75,85

1280x960 60,75,85

1280x1024 60,75,85,100,120

60,75,85,100 60,75,85,100

60,75,85

60,75,85

60,75,85

60,75,85

60,75,85,100,120 60,75,85,100,120

1400x1050 60,75,85 60,75,85 60,75,85

1600x900 60,75,85,100,120 60,75,85,100,120 60,75,85,100,120

1600x1200 60,75,85,100,120 60,75,85,100,120 60,75,85,100,120

1856x1392 60,75

1920x1080 60,75,85,100

1920x1200 60,75,85

1280x1024 60,75

1920x1440 60,75,85

2048x1536 60,75

60,75 60,75

60,75,85,100 60,75,85,100

60,75,85

60,75

60,75,85

60,75

60,75,85

60,75

60,75,85

60,75

25 / 50

PEB-7604VG3A User’s Manual

3.4.2 Triple Marvell Gigabit Ethernet Controller

Triple Marvell Gigabit Ethernet 10/100/1000BASE-TX controller by PCI Express.

The PEB-7604VG3A series provide three LED indicators on RJ-45 connectors to show LAN interface status. These messages will give you a guide for troubleshooting.

Yellow LED indicates transmit and receive activity.

Blinking: indicates transmit/receive activity

On: indicates no activity but link is valid

Off: link is invalid

Green LED indicates Link speed

On: link speed at 1000Mbps

On: link speed at 100Mbps

Off: link speed at 10Mbps

PEB-7604VG3A series provide on CD-Title to support on-board VGA and Ethernet device drivers in various operating systems. Before installing the device drivers, please see the reference files in each sub-directory. You cannot install drivers from CD-Title directly.

Intel 915GM Chipset Integrated Graphics supports Win2000, XP, Win2003 and 64bit

Windows environment.

Intel 915GM & ICH6(M) Chipset Driver supports Win2000, XP, Win2003 and 64bit

Windows environment.

Three Marvell Gigabit Ethernet Controllers support Win2000, XP, Win2003, and 64 bit

Windows environment.

26 / 50

PEB-7604VG3A User’s Manual

CHAPTER 4

27 / 50

PEB-7604VG3A User’s Manual

Phoenix-Award BIOS has a built-in setup program that allows users to modify the basic system configuration. This information is stored in CMOS RAM whose power is supplied by a battery so that it can retain the setup information even when the power is turned off. Press

Delete when you Power on or Reboot the computer system. (i.e. After the logo appears at the center of the screen, please press Delete to enter the BIOS setup program). In the

BIOS, make sure that everything is working fine before you try to optimize it for maximum performance.

When you enter the PHOENIX-AWARD™ CMOS Setup Utility, the Main will appear on the screen. The Main allows you to select several configuration options. Use the left/right arrow keys to highlight a particular configuration screen from the top menu bar or use the down arrow key to access and configure the information below.

28 / 50

4.2.1 Standard CMOS Features

PEB-7604VG3A User’s Manual

4.2.1.1 Date (mm/date/year) and Time (hh/mm/ss)

Allow you to change the date and time of the system clock. No matter how good the quality of the motherboard, remember that losing (or gaining) several seconds per month is not a surprising thing.

4.2.1.2 IDE Channel 0 Master/Slave

You can press Enter to see the submenus they contain.

4.2.1.3 Video

Allows you to select the type of displaying standard you are using. Available options are

EGA/VGA, CGA 40, CGA 80 and MONO.

Select the situation in which you want the BIOS to stop the POST process and notify you.

Available options are All Errors, No Errors, All, but keyboard, All, but diskette, and All,

but disk/key.

Displays the amount of conventional memory detected during boot up.

Displays the amount of extended memory detected during boot up.

Displays the total memory available in the system.

29 / 50

4.2.2 Advanced BIOS Features

PEB-7604VG3A User’s Manual

4.2.2.1.1 Delay Prior to Thermal

Select the delay thermal time. Configuration options: [4min][8min][16min][32min]

30 / 50

PEB-7604VG3A User’s Manual

4.2.2.1.2 Thermal Management

This BIOS feature controls the activation of the Thermal Monitor’s automatic mode. It allows you to determine when the Pentium M4’s Thermal Monitor should be activated in automatic mode after the system boots. In general, the Thermal Monitor should not be activated immediately on booting since the processor will be under a heavy load during the booting process, which results in the sharp rise in die temperature from its cold state, which leads to the unstable system. Therefore, to ensure optimal booting performance, the activation of the Thermal Monitor must be delayed for a set period of time. But how do you possibly know the optimal delay time? It is recommended that you set this to its lowest value that exceeds the time it takes to fully boot up your computer.

This item will monitor the CPU thermal to prevent the CPU damage from high temperature.

4.2.2.1.3 TM2 BUS Ratio

Select the Represents the frequency (bus ratio of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot

4.2.2.1.4 TM2 BUS VID

Select Represents the voltage of the throttled performance state that will be initiated when the on die sensor goes from not hot to hot.

4.2.2.1.5 Limit CPUID MaxVal

When the limit CPUID MaxVal is set to 3, the item should be set to “Disabled” for Windows

XP. Options: Enabled、Disabled (default).

4.2.2.1.6 C1E Function

Select CPU C1E Function Select

4.2.2.1.7 Execute Disable Bit

Select when disable, forces the XD feature flag to always return 0.

4.2.2.1.8 Virtualization Technology

Select when enable, a VMM can utilize the additional hardware capabilities provided by

Vander pool Technology.

31 / 50

PEB-7604VG3A User’s Manual

4.2.2.2 Hard Disk Boot Priority

Select removable device priority, such as Pri.Master, Pri,Slave, USBHDD0, USBHDD1,

USBHDD2, and Bootable Add-in Cards.

Allows to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempts to write data into this area, BIOS will show a warning message on screen and alarm beep.

4.2.2.4 CPU L1 & L2 Cache

Cache memory is much faster than conventional DRAM system memory. These fields allow you to enable or disable the CPUs Level 1 built-in cache and Level 2 external cache. Both settings are left as Enabled to significantly enhance the performance of your computer.

When you install a CPU featuring Hyper-Threading Technology, this item will allow you to enable or disable the Hyper-Threading technology. Options: Disabled、Enabled (default).

4.2.2.6 Quick Power On Self Test

Enable this function to reduce the amount of time required to run the POST (Power On Self

Test). BIOS will save time by skipping certain tests during POST. It is recommended that you disable this setting. Finding a problem during boot up is better than loosing data during your work.

4.2.2.7 First/Second/Third Boot Device

Allow you to select the First, Second and Third Boot Device. If your computer is newly constructed, the next thing you want to do is load the Operating System from scratch, directly off its CD. Before that, you need to set the First Boot Device to the CDROM. This instructs the BIOS to boot from the CD drive before trying to boot from the hard drive, which is still blank.

32 / 50

PEB-7604VG3A User’s Manual

4.2.2.8 Boot Up NumLock Status

This function defines the keyboard's numberpad as number keys or arrow keys. If it is set at

On the number keys will be activated, if it is set at Off the arrow keys will be activated.

4.2.2.9 Typematic Rate Setting

When enabled, you can set the following two-typematic control items. When disabled, the keyboard controller determines keystrokes arbitrarily in your system.

4.2.2.10 Typematic Rate (Chars/Sec)

The typematic rate sets the rate at which characters on the screen repeat when a key is pressed and held down.

4.2.2.11 Typematic Delay (Msec)

The typematic delay sets how long after you press a key that a character begins repeating.

4.2.2.12 APIC Mode

By enabling this option, “MPS version control for OS” can be configured. Disabled is recommended.

4.2.2.13 MPS Version Control for OS

The 1.1 version is the older version that supports 8 more IRQs in the Windows NT environment. Choose the new 1.4 version for Windows 2000 and Windows XP. Options: 1.4

(default)、1.1

4.2.2.14 OS Select For DRAM > 64MB

IBM’s relic. If your system's DRAM is larger than 64MB and you are running OS/2, select

OS/2 as the item value. Otherwise, set the item value to Non-OS/2 for all other operating systems.

33 / 50

4.2.3 Advanced Chipset Features

PEB-7604VG3A User’s Manual

4.2.3.1 DRAM Timing Selectable

This item determines DRAM clock/timing using SPD or manual configuration. Make sure your memory module has SPD (Serial Presence Data), if you want to select the “By SPD” option. Options: Manual、By SPD (default)

4.2.3.2 CAS Latency Time

CAS is short for column address strobe, which is a kind of signals. When the CPU needs data from SDRAM, CAS signals will be sent via the CAS line to specify the column where the data is needed. This controls the time delay (in clock cycles - CLKs) that passes before the SDRAM starts to carry out a read command after receiving it. This also determines the number of CLKs for the completion of the first part of a burst transfer. In other words, the lower the latency, the faster the transaction.

Note that some SDRAM modules may not be able to handle the lower latency and will become unstable and lose data. Therefore, set the DRAM CAS Latency Time to 2 for optimal performance if possible but increase it to 2.5 if your system becomes unstable.

Interestingly, increasing the CAS latency time does have an advantage in that it will enable the SDRAM to run at a higher clockspeed, thereby giving you an edge in overclocking your system. So, if you hit a snag while overclocking, try increasing the CAS latency time.

4.2.3.3 DRAM RAS# to CAS# Delay

This item allows you to select a delay time between the CAS and RAS strobe signals. It only applies when DRAM is written to, read from, or refreshed. This field is adjustable only when “DRAM Timing Selectable” is set to “manual”. This field is locked when “DRAM

Timing Selectable” is set to “By SPD” and is automatically determined by the system.

Options: 5、4、3、2.

34 / 50

PEB-7604VG3A User’s Manual

4.2.3.4 DRAM RAS# Precharge

This item allows you to select the DRAM RAS# precharge time. The ROW address strobe must precharge again before DRAM is refreshed. An inadequate configuration may result in incomplete data. This field is adjustable only when “DRAM Timing Selectable” is set to

“manual”. This field is locked when “DRAM Timing Selectable” is set to “By SPD” and is automatically determined by the system. Options: 5、4、3、2.

This item allows you to select DRAM Active to Precharge Delay. This field is locked when

“DRAM Timing Selectable” is set to “By SPD” and is automatically determined by the system. Options: 15、14、13、12、11、10、9、8、7、6、5、4.

4.2.3.6 System BIOS Cacheable

Enabling this function allows caching of the system BIOS ROM at F0000h-FFFFFh, which results in better system performance. However, if any program writes to this memory area, a system error may result. It is advisable to leave it in default setting. Caching the system

BIOS results in better performance than shadowing the system BIOS.

4.2.3.7 Video BIOS Cacheable

Select “Enabled” to allow caching of the video BIOS which may improve performance. If any other program writes to this memory area, a system error may result. Options: Enabled,

Disabled (default)

4.2.3.8 Memory Hole at 15M-16M

Enabling this function will reserve the memory address space between 15MB and 16MB for

ISA expansion cards. However, it will also result in not allowing the system to have access to memory above 16MB. Please note that some expansion cards require this setting to be enabled. The default setting is Disabled. If Auto Configuration is enabled, you must set the

DRAM timing function to 60ns or 70ns, depending on the type of DRAM you install.

4.2.3.9 PCI Express Root Port Function

This item allows to Enable/Disable PCI Express port and select the PCI Express

Compliancy mode from v1.0a to v1.0.

4.2.3.10 On-Chip Frame Buffer Size

This item allows you to setting the VGA memory form share system. Options:

1M(minimum)、8M(Maximum default)

4.2.3.11 DVMT Mode

DVMT/FIXED Memory Size

4.2.3.12 Boot Display

This item allows you to setting CRT monitor only or CRT with EFP(DVI) together display.

35 / 50

PEB-7604VG3A User’s Manual

4.2.3.13 Panel Scaling

This item is for the backlight scaling techniques dynamically dimming the backlight to conserve its power consumption as increasing the panel transmittance to maintain the same luminance. Most displays use either spatial or temporal method to synthesize colors.

4.2.3.14 Panel Number

This item allows to select panel resolution that will be displayed depending on the LCD panel (LFP).

36 / 50

PEB-7604VG3A User’s Manual

4.2.4.1 Onchip IDE Device

4.2.4.3.1 IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sector read/write.

If the IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support.

4.2.4.3.2 IDE DMA Transfer Access

This item could allows you to enabled/disabled the IDE UDMA transfer function and only use PIO mode

37 / 50

PEB-7604VG3A User’s Manual

4.2.4.3.3 On-Chip Primary/Secondary PCI IDE

The chipset contains a PCI IDE interface with support for two IDE channels. Select Enabled to activate the primary IDE interface. Select Disabled to deactivate this interface.

4.2.4.3.4 IDE Primary/Secondary Master/Slave PIO

The IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device.

4.2.4.3.5 IDE Primary/Secondary Master/Slave UDMA

Ultra DMA implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If the hard drive and the system software both support Ultra DMA, select

Auto to enable BIOS support.

4.2.4.3.6 On-Chip Serial ATA

The chipset contains a SATA IDE interface with support for two IDE channels. Select

Enabled to activate the primary IDE interface (Channel0). Select Disabled to deactivate this interface.

4.2.4.3.7 PATA IDE Mode

This function allows to select PATA IDE mode.

38 / 50

PEB-7604VG3A User’s Manual

4.2.4.3.1 USB Controller

This item allows you to set the USB Controller.

4.2.4.3.2 USB 2.0 Controller

This item allows you to set the USB 2.0 Controller.

4.2.4.3.3 USB Keyboard Support

This item allows you to set the system’s USB keyboard to Enabled/Disabled.

4.2.4.3.4 USB Mouse Support

This item allows you to set the system’s USB Mouse to Enabled/Disabled.

4.2.4.3.5 Azalia/AC97 Audio Select

This option is used to Set whether onboard Azalia/AC97 audio is enabled

39 / 50

4.2.4.3 Super IO Device

PEB-7604VG3A User’s Manual

4.2.4.3.1 Onboard Serial Port 1/2

Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you are not going to use FDC or the system has no floppy drive, select Disabled in this field.

4.2.4.3.2 UART Mode Select

Select an address and corresponding interrupt for the first and second serial ports.

4.2.4.3.3 RxD,TxD Active

This BIOS feature allows to set the infra-red reception (RxD) and transmission (TxD) polarity. There are four options available, based on combinations of Hi and Lo. Please consult the IR peripheral's documentation to determine the correct polarity, or the wrong polarity will prevent a proper IR connection from being established with the IR peripheral.

4.2.4.3.4 IR transmission Delay

The field enables or disables IR transmission delay function.

4.2.4.3.5 UR2 Duplex Mode

Select the value required by the IR device connected to the IR port. Full-duplex mode permits simultaneous two-direction transmission. Half-duplex mode permits transmission in one direction only at a time.

4.2.4.3.6 Use IR Pins

Select the correct setting of TxD and RxD signals.

4.2.4.3.7 PWRON After PWR-Fail

This item is to set whether to run Ac Loss Auto Restart or off

4.2.4.4 Watch Dog Timer Select

This function will determine watch dog timer during the range of 10 Sec., 20 Sec., 30 Sec.,

40 Sec., 1 Min., 2 Min., and 4 Min. The default setting is Disabled.

40 / 50

4.2.5 Power Management Setup

PEB-7604VG3A User’s Manual

This function enables PCs to implement Power Management functions through Operating

System and also provides the opportunity to integrated the interface for controlling power management and Plug-n-Play features on system devices.

4.2.5.2 ACPI Suspend Type

This item allows to set the ACPI suspend (sleep) mode instead of simply turning off a computer. In S1 the computer consumes less power because HDDs and some other devices are powered off, but CPU is still running and it requires its fan to rotate. In S3 mode it's only RAM (system memory) that remains powered.

41 / 50

PEB-7604VG3A User’s Manual

4.2.5.3 Run VGABIOS if S3 Resume

This item is to select whether to run VGABIOS if resumed from S3 state but for older VGA drivers only. Please select Auto (Default) if in doubt.

There are three selections for power management and HDD power down. The Min. Power

Saving sets the HDD Power Down at 15 Min., Max. Power Saving at 1 Min., and User defined from 1 Min. to 15 Min. and disabled but from 1 Min. to 1 hour while disabled.

4.2.5.5 Video Off Method

Determines the manner in which the monitor is blanked. V/H SYNC + Blank turns off vertical and horizontal synchronization ports and writes blanks to the video buffer; DPMS

Support is for the monitor supports the Display Power Management Signaling(DPMS) standard of the Video Electronics Standards Association(VESA); Blank Screen set the system only writes blanks to the video buffer.

4.2.5.6 Video Off In Suspend

This item allows to set if the monitor is blanked in Suspend mode. The default setting is

Yes.

This item will set the system status to shut down the PC with choices of Stop Grant and

PwrOn Suspend.

4.2.5.8 MODEM Use IRQ

This determines the IRQ in which the MODEM can use.

4.2.5.9 Sort-Off by PWR-BTTN

Pressing the power button for more than 4 seconds/Instant-Off forces the system to enter the Soft-Off state when the system has “hung”.(Only could working on ATX Power supply).

4.2.5.10 Wake-Up by PCI Card

This will enable the system to wake up through PCI Card peripheral or not.

4.2.5.11 Power On by Ring

The function allows the system boot up if there’s an incoming call from the modem.

4.2.5.12 USB KB Wake-Up From S3

This option is used to enabled/disabled USB keyboard wake up with suspend to RAM.

4.2.5.13 Primary/Secondary IDE 0/1

This function is for setting IDE 0/1 on primary/secondary mode.

4.2.5.14 FDD,COM,LPT Port

System can be awaked by Floppy Drive, COM or LPT port.

4.2.5.15 PCI PIRQ[A-D]#

This function will cause the system waking up completely from the power management mode.

42 / 50

PEB-7604VG3A User’s Manual

4.2.6.1 Init Display First

This item allows you to decide to active whether PCI Slot or Onboard/AGP first.

4.2.6.2 Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset Extended System

Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system cannot boot.

4.2.6.3 Resources Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows

®95. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field.

43 / 50

PEB-7604VG3A User’s Manual

4.2.6.3.1 IRQ Resources

This item allows you to determine the IRQ assigned to the ISA bus and is not available to any PCI slot. Legacy ISA for devices compliant with the original PC AT bus specification,

PCI/ISA PnP for devices compliant with the Plug and Play standard whether designed for

PCI or ISA bus architecture.

4.2.6.3.2 DMA Resources

This item allows you to determine the DMA assigned to the ISA bus and is not available to any PCI slot. Legacy ISA for devices compliant with the original PC AT bus specification,

PCI/ISA PnP for devices compliant with the Plug and Play standard whether designed for

PCI or ISA bus architecture.

44 / 50

PEB-7604VG3A User’s Manual

4.2.6.4 PCI/VGA Palette Snoop

This function determines if the graphics card should allow VGA palette snooping by a fixed function display card. It is only useful if a fixed-function display card using that requires a

VGA-compatible graphics card to be present. Otherwise, leave the setting as default

Disabled.

This item allows to set the maximum TLP payload size (unit in byte) for the PCI Express devices.

4.2.7 PC Health Status

This item allows to shutdown the system while the temperature is overheated.

4.2.7.2 CPU Warning Temperature

This function sets the CPU temperature value when the system will warn you about possible overheating issue.

4.2.7.3 Smart CPU FAN Temperature

The Smart CPU Fan option in the BIOS slows down the fan when the CPU is below a given temperature.

45 / 50

PEB-7604VG3A User’s Manual

4.2.8.1 Auto Detect PCI/DIMM Clk

This item allows to enable/disable auto detect PCI/DIMM clock.

This is to adjust extreme value of the pulse for EMI test.

4.2.9 Load Fail-Safe Default

Use this menu to load the BIOS default values for the minimal/stable performance for your system to operate.

Press <Y> to load the BIOS default values for the most stable, minimal-performance system operations.

46 / 50

PEB-7604VG3A User’s Manual

4.2.10 Load Optimized Defaults

Use this menu to load the BIOS default values that are factory settings for optimal performance system operations. While Award has designed the custom BIOS to maximize performance, the factory has the right to change these defaults to meet their needs.

Press <Y> to load the default values setting for optimal performance system operations.

4.2.11 Supervisor/User Password Setting

You can set either supervisor or user password, or both of them.

Supervisor Password: able to enter/change the options of setup menus

47 / 50

PEB-7604VG3A User’s Manual

User Password: able to enter but no right to change the options of setup menus.

Type the password, up to eight characters in length, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password. To disable a password, just press <Enter> when you are prompted to enter the password. A message will confirm the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration. Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer. You determine when the password is required within the BIOS

Features Setup Menu and its Security option (see Section 3). If the Security option is set to

“System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup

48 / 50

PEB-7604VG3A User’s Manual

Save CMOS value changes to CMOS and exit setup. Enter <Y> to store the selection made in the menus in CMOS, a special section in memory that stays on after turning the system off. The BIOS configures the system according to the Setup selection stored in CMOS when boot the computer next time. The system is restarted after saving the values.

Abandon all CMOS value changes and exit setup, and the system is restarted after exiting

49 / 50

PEB-7604VG3A User’s Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement