Installation Guide & User Manual
Installation Guide & User Manual
Standalone Metal RFID Series
Version: 2.1
Date: January, 2015
Important Note
Document Privacy Note:
Firstly thank you for purchasing the product. Before use, please read this manual
carefully to avoid the unnecessary damage! The company reminds you that the proper
user will improve the use affect and authentication speed. No written consent by
company, any unit or individual isn’t allowed to excerpt, copy the content of this manual
in part or in full, also spread in any form.
Document use statement:
Due to the constant renewal of products, the company can not undertake the actual
product in consistence with the information in the document, also any dispute caused by
the difference between the actual technical parameters and the information in this
document. Please forgive any change without notice. Reserve the final rights of
modification and interpretation.
Contents
Installation Guide
1. Equipment Installation
2. Structure and Function
3. Lock Connection
4. Connected with Other Parts ………………………………………………………………IV
5. Connect with Power…………………………………………………………..……………IV
User Manual
1. User Management..................................................................................................... 1
1.1 Administrator Operations .................................................................................. 1
1.2 Add Users ........................................................................................................ 2
1.3 Register Eight Passwords for Opening the Door .............................................. 3
1.4 Authenticate User ............................................................................................. 3
1.5 Delete Users .................................................................................................... 4
2. Access Control Management .................................................................................... 5
2.1 Configure Unlocking Duration .......................................................................... 5
2.2 Configure Authentication Mode ........................................................................ 5
2.3 Configure Concealed Mode .............................................................................. 6
2.4 Configure Door Sensor Mode ........................................................................... 6
2.5 Configure Alarm ............................................................................................... 7
2.6 SRB ................................................................................................................. 8
2.7 Factory Reset................................................................................................... 9
3. Switch Working Mode................................................................................................ 9
3.1 Controller Mode Switch to Reader Mode .......................................................... 9
3.2 Reader Mode Switch to Controller Mode ........................................................ 10
Appendix ..................................................................................................................... 11
Packing List ................................................................................................................ 11
1. Equipment Installation
1
Optical Tamper Switch
2
Remove the screw on
the bottom of device.
4
3
Fix the back cover on
the wall.
6
5
Fix the device to the
back cover.
Fix the screw.
Please pick off the plastic
6
Exposed wire
Take away the
back cover.
when exposed wire
Buried wire
I
2. Structure and Function
Access Control System Function
(1) If a registered user is verified, the device will send a signal to unlock
the door.
(2) Door Sensor will detect the door is open or not. If the door is
unexpectedly opened or improperly closed, the alarm will
be triggered.
(3) It supports Exit Button; it is convenient to open the door inside.
(4) It supports Smoke Detector etc., it will alarm and open the door when
receives the signal of detector.
(5) It supports Door Bell; visitors could call by the door bell.
(6) If the device is dismantled, it will send an alarm signal.
 Linkage Function
This device has an Auxiliary Input interface (AUX+) which allows it to be
connected with an external source, for instance a smoke detector, gas
detector, infrared sensor or emergency switch.
Trigger Linkage
Once detectors or sensors are connected to AUX+ and are triggered, the
II
system receives the linkage signal and would generate an alarm and open
the door, the door keeps open and alarm keeps on until the linkage
is canceled.
Cancel Linkage
The linkage can be canceled when a user is verified, or the Administrator
opens the door with password.
3. Lock Connection
Warning: No operation when power on!
(1) The system supports NO LOCK and NC LOCK. For example the
NO LOCK (normally open by power on) is connected with NO
terminal, and the NC LOCK is connected with NC terminal.
(2) When the Electrical Lock is connected to the Access Control
System, you need to parallel one FR107 diode (equipped in the
package) to prevent the self-inductance EMF affecting the system,
do not reverse the polarities.
(I) Share power with the lock
 ULOCK=12V, I ≥ IDevice + ILock (The maximum operating current of
device is 100mA, and the rated current is 60mA);
 And the lock is near to the device.
III
(II) Does not share power with the lock
Device does not share power with the lock:
 ULOCK=12V, I < IDevice + ILock (The maximum operating current of
device is 100mA, and the rated current is 60mA);
 ULOCK≠12V;
 The lock is far from the device.
I: device output current; ULOCK: lock voltage; ILOCK: lock current.
5. Connect with Power
4. Connect with Other Parts
Voltage output ≤ DC 12V for Alarm
IV
Input DC12V, ≤110mA (≤80mA
standby) Positive is connected
with +12V, negative is connected
with GND (do not reverse
the polarities).
Recommended procedure
Step 1: Power on after the device is completely installed on the wall.
Step 2: Change the administrator password, and configure access control parameters,
including unlocking duration, authentication mode, concealed mode, door sensor mode,
and alarm etc.
Step 3: Register users' cards, or eight passwords.
1. User Management
1.1 Administrator Operations
To ensure data security of the device, you can operate the device only after the
administrator password is authenticated.
 Authenticate the Administrator Password
1. Press [*]
(The indicator is off and
makes a long beep.)
2. Press [#] .
(You can authenticate
the password.)
3. Enter the administrator
password. (The initial
password is 1234.)
5. Exit. (Press [*] or do
not operate the device
within 20 seconds ,The
indicator turns red and
makes a long beep, then
automatically exit.)
4. The authentication is
successful. (The indicator
turns blue.)
Yes
Note: The initial administrator password is 1234.
 Change Administrator Password
1. The administrator
password is authenticated.
2. Press [8]. (You can
change the password.)
3. Enter a new
administrator password.
Failed.
(The indicator turns red
and makes three beeps.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. Succeed. (The
indicator turns blue and
the makes a long beep.)
Yes
4. Enter the new
administrator password
again for authentication.
Note: Four-digit passwords are automatically verified. For passwords with less than
four digits, press [#] to enter the verification process.
1
 Open the Door by Entering the Administrator Password
1. The administrator
password is authenticated.
2. Press [0]. (The
indicator turns blue and
makes a long beep.)
3. Press [0]. (The
indicator turns blue and
makes a long beep.)
5. Exit. (The indicator
turns red and makes a
long beep, then
automatically exit.)
4. The door is opened
(The indicator turns blue
and makes a long beep.)
Note: This function can be used to open the door.
 Administrator Password is Forgotten?
If the administrator password is forgotten, please dismantle the device and wait 30
seconds when there is a long beep, then press the Optical Tamper Switch three times to
reset to the initial administrator password, each press shall take 2~5 seconds and it
comes a beep each time, note this operation must be done within 30 seconds. It is
successfully reset when it has a long beep after the third press; the Red LED blinks and
quits the operation by itself.
Note: The initial administrator password is 1234.
1.2 Add Users
Register the card of a user or register cards in batches.
 Add Users
1. The administrator
password is
authenticated.
2. Press [1].
(The indicator turns blue
and makes a long beep.)
4. Register cards.
( Swipe the card once.)
3. Input user ID twice
(The indicator turns blue
and makes a long beep.)
6. Exit. (Press [*], the indicator
turns red and makes a long
beep, then automatically exit. )
4. Register cards.
( Swipe the card once.)
5. Adding users successfully.
(The indicator turns blue and
makes a long beep.)
Note:
1. Nine-digit user ID is automatically verified. For user ID with less than nine-digit, press
[#] to confirm.
2. If the user ID is not available, the ID number increases automatically. It continues to
register new one once a user is successfully registered.
3. The registration fails if the user ID or the card has been registered (the indicator turns
2
red and makes three short beeps). When the indicator turns blue, you can register the
user again. If you fail in swiping card or entering user ID three times, the device will
enter the standby state.
 Register Cards in Batches
1. The administrator
password is authenticated.
2. Press [6]. (Registering
Cards in Batches.)
3. Swipe the first card once.
(Swipe the card once.)
Failed.
(The indicator turns red
and makes three beeps.)
6. Exit.
(The indicator turns red
and makes a long beep,
then automatically exit.)
5. Cards are registered
in batches successfully.
Yes
4. Enter the total number
of cards.
Note:
1. In the process of entering the total number of cards, three-digit numbers are
automatically verified. For numbers with less than three digits, press [#] to enter the
verification process. Press [*] to reenter the total number of cards.
2. IDs of to-be-registered cards must be consecutive numbers.
1.3 Register Eight Passwords for Opening the Door
This device supports 8 passwords, each password has a Group ID ranges from 1~8.
The default password value is 0 for all groups, which means passwords are disabled.
You can modify the passwords under 8 groups to open the door.
1. The administrator
password is
authenticated.
2. Press [3].
(The indicator turns blue
and makes a long beep.)
3. Enter the group ID of
password.(Group ID: 1 ~ 8.)
7. Exit. (Press [*], the
indicator turns red and
makes a long beep, then
automatically exit)
6. Register successfully.
(The indicator turns blue
and makes a long beep.)
4. Enter the password
twice.
(The password consists of
four digits.)
Note: If a password is successfully changed, enter the Group ID to change next one.
1.4 Authenticate User
Card / Password Authentication
3
After the device is powered on, it enters the authentication state for unlocking the door.
1. The device is in the
authentication state.
2. Swipe the card, or enter Yes 3. The authentication is
the password. Press [#]
successful. (The indicator
after entering the
turns blue and makes a
password.
long beep.)
Failed.
(The indicator turns red and
makes two short beeps.)
Note: Press [#] after entering a password for authentication. The door opens if the
entered password is identical with one of the eight passwords for opening the door.
1.5 Delete Users
Delete a user whose card is registered, or delete all users.
 Delete a User
1. The administrator
password is authenticated.
2. Press [2]. (The indicator
turns blue and makes a
long beep.)
3. Swipe the user card or
input user ID once which
to be deleted.
Failed.
(The indicator turns red
and makes three beeps.)
6. Exit. (Press [*] or do not
operate the device within 20
seconds, the indicator turns
red and makes a long beep,
then automatically exit.)
5. The user is deleted.
(The indicator turns blue
and makes a long beep.)
Yes
4. Determine whether the
user is authentic. (The
indicator turns blue and
makes a long beep.)
Note:
1. You can swipe the card or input user ID to delete a user. Nine-digit user ID is
automatically verified. For user ID with less than nine-digit, press [#] to confirm.
2. The device automatically enters the process of deleting the next user when a user is
deleted, or press [*] to exit.
4
 Delete All Users
1. The administrator
password is authenticated.
2. Press [9]. (The indicator
turns blue and makes a
long beep.)
3. Press [9]. (The
indicator turns blue and
makes a long beep.)
5. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
4. Deleting All Users is
successful. (The indicator
turns blue and makes a
long beep.)
Note: Press [9] for automatic confirmation. Other values are considered invalid. If an
invalid value is entered, the device indicator turns red, and the device makes a long
beep and exits the process.
2. Access Control Management
2.1 Configure Unlocking Duration
1. The administrator
password is
authenticated.
2. Press [4]. (The indicator
turns blue and makes a
long beep.)
3. Enter the unlocking
duration. (range: 1s to 254s)
5. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
4. The unlocking duration is
modified. (The indicator
turns blue and makes a
long beep.)
Note: The unit of Unlocking Duration is second. Three-digit values are automatically
verified. For values with less than three digits, press [#] to enter the verification process.
2.2 Configure Authentication Mode
1. The administrator
password is authenticated.
2. Press [5]. (The indicator
turns blue and makes a
long beep.)
3. Enter the
authentication mode.
5. Exit. (The indicator turns
red and makes a long beep,
then automatically exit.)
4. The configuration is
successful. (The indicator
turns blue and makes a
long beep.)
5
Note:
1. When the authentication mode is RF & password, swipe card and then enter the
passwords please.
2. Details about the authentication modes are as follows:
Authentication Mode
Value
Description
PW
1
Only password verification
RF
2
Only RF Card verification
RF/PW (default)
3
RF or password verification
RF&PW
4
RF and password verification
2.3 Configure Concealed Mode
If the Concealed Mode is enabled, the indicator is off.
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [3].
(The indicator turns blue
and makes a long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. The configuration is
successful. (The indicator
turns blue and makes a
long beep.)
4. Configure the
concealed mode.
(0: enable; 1: disable).
Note: An indicator blinks to indicate the status of this function when users are
authenticating their cards or passwords.
2.4 Configure Door Sensor Mode
The door sensor has three modes:
● NONE: The door sensor is disabled.
● NO: The door sensor will send an alarm signal if it detects the door is closed.
● NC: The door sensor will send an alarm signal if it detects the door is open.
6
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [5]. (The indicator
turns blue and makes a
long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. The configuration is
successful. (The indicator
turns blue and makes a
long beep.)
4. Configure the door
sensor mode. (0: Normally
Open; 1: Normally Closed;
2: Disabled).
Note: The door sensor mode configured here is used as the basis for the door
sensor alarm.
2.5 Configure Alarm
 Configure Alarm Switch
The alarm switch is turned on by default. When it’s disabled, then Error
Operation-Triggered Alarm and the Alarm Delay for the Door Status Sensor will be
disabled, but Tamper Alarm still works.
1. The administrator
password is authenticated.
2. Press [0]. (The
indicator turns blue and
makes a long beep.)
3. Press [1]. (The indicator
turns blue and makes a
long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. The configuration is
successful. (The
indicator turns blue and
makes a long beep.)
4. Configure the alarm
setting. (0: enable; 1:
disable).
 Configure Error Operation-Triggered Alarm
Alarms will be generated if the administrator fails the authentication upon three attempts
under this function enabled, and it is not allowed to continue within 20 seconds.
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [2]. (The
indicator turns blue and
makes a long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. The configuration is
successful.
(The indicator turns blue
and makes a long beep.)
4. Configure the error
operation-triggered
alarm switch. (0: enable;
1: disable)
7
 Configure Tamper Alarm
If this function is enabled, alarms will be generated when device is dismantled from
the wall.
1. The administrator
password is authenticated.
2. Press [7]. (The indicator
turns blue and makes a
long beep.)
3. Configure whether to
enable the tamper alarm.
(0: enable; 1: disable)
5. Exit. The indicator turns
red and makes a long
beep, then automatically
exit.)
4. The configuration is
successful. (The indicator
turns blue and makes a
long beep.)
 Configure Alarm Delay for the Door Status Sensor
DSen. Delay (Door Sensor Delay):
It is to configure the time how long would the door sensor would do check the door
status.
1. The administrator
password is
authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [4].
(The indicator turns blue
and makes a long beep.)
6.Exit.
(The indicator turns red
and makes a long beep,
then automatically exit.)
5. The configuration is
successful.
(The indicator turns blue
and makes a long beep.)
4.Configure the alarm
delay. (range: 1s to 254s)
Note: Three-digit values are automatically verified. For values with less than three
digits, press [#] to confirm. Values greater than 254 are considered invalid.
2.6 SRB
Security Relay Box (SRB) is a relay switch to control electric lock, exit button to provide
higher security level for access control.
It is installed on a secured place and connected with standalone access control devices
by Wiegand out.
Note: For electrical parameters and connection guide, please consult SRB Simple
Access Controller Connection Guide.
8
2.7 Factory Reset
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [9]. (The indicator
turns blue and makes a
long beep.)
6.Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. The configuration is
successful.
(The indicator turns blue
and makes a long beep.)
4. Press [9]. (a short beep)
The Factory Default Settings
Unlock Authentication Mode
Door Sensor Mode
Alarm Switch
Error Operation-Triggered Alarm Switch
Tamper Alarm Switch
Concealed Mode
Unlocking Duration
Door Sensor Delay
RF/PW
None
Enabled
Enabled
Enabled
Disabled
5 seconds
15 seconds
3. Switch Working Mode
This device could work as a standalone controller or as a wiegand reader, which offers
flexibility to use depending on actual needs. It is a standalone controller by default
setting but you could switch the working mode by the following instruction.
If the indicator blinks blue, indicates that the device is set to Controller Mode.
If the indicator stays in red, indicates that the device is set to Reader Mode.
Note: For wiring diagram of reader mode, please consult Appendix.
3.1 Controller Mode Switch to Reader Mode
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. Set mode successfully.
(The indicator turns blue
and makes a long beep.)
3. Press [6]. (The indicator
turns blue and makes a
long beep.)
4. Press [1].
(The indicator turns blue
and makes a long beep.)
Note: The device makes three short beeps when fails in setting, then the indicator
turns red and makes a long beep, then automatically exit.
9
Set Weigand Format
When the device is in Reader Mode, hold and press [*] five seconds, press [#] when the
red indicator turns off, then input administrator password to enter the device. It can be
set to Weigand 26 or Weigand 34.
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. Set format successfully.
(The indicator turns blue
and makes a long beep.)
3. Press [7]. (The indicator
turns blue and makes a
long beep.)
4. Set Weigand format
(0:WG26, 1:WG34.)
Note: The device makes three short beeps when fails in setting, then the indicator
turns red and makes a long beep, then automatically exit.
3.2 Reader Mode Switch to Controller Mode
When the device is in Reader Mode, hold and press [*] five seconds, press [#] when the
red indicator turns off, then input administrator password to enter the device.
1. The administrator
password is authenticated.
2. Press [0]. (The indicator
turns blue and makes a
long beep.)
3. Press [6]. (The indicator
turns blue and makes a
long beep.)
6. Exit. (The indicator turns
red and makes a long
beep, then automatically
exit.)
5. Set mode successfully.
(The indicator turns blue
and makes a long beep.)
4. Press [0].
(The indicator turns blue
and makes a long beep.)
Note: The device makes three short beeps when fails in setting, then the indicator
turns red and makes a long beep, then automatically exit.
10
Appendix
Wiring Diagram of Controller Mode
Wiring Diagram of Reader Mode
Red: DC 12V
Light Blue: SEN
Red: DC 12V
Black: GND
Black: GND
Gray: BUT
Green: WD0
White: WD1
Light Blue: LED
Yellow: NC
Purple: BELL+ (Bell)
Gray: BEEP
Pink: COM
Brown: BELL- (Bell)
Purple: BELL+ (Bell)
Blue: NO
Brown: BELL- (Bell)
Weigand Output
Linkage Function
Green: WD0
Orange: AL (Alarm)
White: WD1
Light Green: AUX+
Packing List
Access Device &
Mounting Plate
4 Screws
1 Card
4 Diodes (FR107)
4 Wall Plugs 1 Star-shaped Screw
11
Screwdriver
1 Installation Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement