advertisement
▼
Scroll to page 2
of 90
SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Library Illumina HiSeq and MiSeq Multiplexed Sequencing Platforms Protocol Version 1.8, October 2014 Before you begin, view hands-on videos of SureSelect procedures at http://www.agilent.com/genomics/protocolvideos. SureSelect platform manufactured with Agilent SurePrint Technology For Research Use Only. Not for Use in Diagnostic Procedures. Notices © Agilent Technologies, Inc. 2014 Warranty No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and international copyright laws. The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applicable law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Agilent shall not be liable for errors or for incidental or consequential damages in connection with the furnishing, use, or performance of this document or of any information contained herein. Should Agilent and the user have a separate written agreement with warranty terms covering the material in this document that conflict with these terms, the warranty terms in the separate agreement shall control. Manual Part Number G7530-90000 Edition Version 1.8, October 2014 Agilent Technologies, Inc. 5301 Stevens Creek Rd Santa Clara, CA 95051 USA Acknowledgment Oligonucleotide sequences © 2006, 2008, and 2011 Illumina, Inc. All rights reserved. Only for use with the Illumina sequencer systems and associated assays. Technology Licenses Technical Support For technical product support, contact your local Agilent Support Services representative. For US and Canada, call (800) 227-9770 (option 3,4,4). For other countries, find your support center telephone numbers at www.agilent.com/chem/contactus. Or send an e-mail to: [email protected] Notice to Purchaser SureSelect capture libraries and reagents must be used within one year of receipt. The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license. Restricted Rights Legend U.S. Government Restricted Rights. Software and technical data rights granted to the federal government include only those rights customarily provided to end user customers. Agilent provides this customary commercial license in Software and technical data pursuant to FAR 12.211 (Technical Data) and 12.212 (Computer Software) and, for the Department of Defense, DFARS 252.227-7015 (Technical Data - Commercial Items) and DFARS 227.7202-3 (Rights in Commercial Computer Software or Computer Software Documentation). Safety Notices CAUTION A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met. WA R N I N G A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing In this Guide... This guide describes the recommended operational procedures to capture the genomic regions of interest using the Agilent SureSelectXT Target Enrichment Kit for Illumina Multiplex Sequencing. This protocol is specifically developed and optimized to use biotinylated RNA oligomer libraries to enrich targeted regions of the genome from repetitive sequences and sequences unrelated to the research focus, specifically adjusted to provide high performance with SureSelect. This guide uses an optimized protocol for Illumina paired-end multiplexed library preparation. 1 Before You Begin This chapter contains information (such as procedural notes, safety information, required reagents and equipment) that you should read and understand before you start an experiment. 2 Sample Preparation (3 µg DNA Samples) 3 Sample Preparation (200 ng DNA Samples) These chapters describe the steps to prepare the DNA samples for target enrichment. 4 Hybridization This chapter describes the steps to prepare and hybridize samples. 5 Addition of Index Tags by Post-Hybridization Amplification This chapter describes the steps to amplify, purify, and assess quality of the sample libraries. Samples are pooled by mass prior to sequencing. 6 Reference This chapter contains information on reagent kit content, SureSelect index sequences, and alternative equipment that can be used with this protocol. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 3 What’s new in 1.8 • Support for SureSelectXT Focused Exome and Exome Plus 1 capture libraries. What’s new in 1.7 • Support for SureSelectXT Clinical Research Exome and SureSelectXT Inherited Disease capture libraries. • D1000 ScreenTape and Reagents replace D1K ScreenTape and Reagents. High Sensitivity D1000 ScreenTape and Reagents replace High Sensitivity D1K ScreenTape and Reagents. What’s new in 1.6 • Support for V5+lncRNA SureSelect capture libraries. • Support for 200-ng DNA Samples input option. • Details added for storage of on-bead captured DNA samples. What’s new in 1.5 • Support for SureSelect Human All Exon V5, V5 Plus, and V5+UTRs capture libraries. • More details provided for the Agilent 2200 TapeStation for DNA quantitation and qualification. • Option to hybridize for 16 hours. What’s new in 1.4 • On-bead PCR procedure replaces in-solution PCR procedure for post-hybridization. • Support for Covaris E-series Sample Preparation system and SonoLab 7 software. 4 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Content 1 Before You Begin 7 Procedural Notes 8 Safety Notes 8 Required Reagents 9 Optional Reagents 11 Required Equipment 12 Optional Equipment 13 2 Sample Preparation (3 µg DNA Samples) 15 Step 1. Shear DNA 19 Step 2. Purify the sample using Agencourt AMPure XP beads Step 3. Assess quality (optional) 22 Step 4. Repair the ends 25 Step 5. Purify the sample using Agencourt AMPure XP beads Step 6. Add ‘A’ Bases to the 3' end of the DNA fragments 27 Step 7. Purify the sample using Agencourt AMPure XP beads Step 8. Ligate the paired-end adaptor 29 Step 9. Purify the sample using Agencourt AMPure XP beads Step 10. Amplify adaptor-ligated library 31 Step 11. Purify the sample with Agencourt AMPure XP beads Step 12. Assess quality and quantity 35 3 Sample Preparation (200 ng DNA Samples) 21 26 28 30 34 39 Step 1. Shear DNA 43 Step 2. Assess quality (optional) 45 Step 3. Repair the ends 46 Step 4. Purify the sample using Agencourt AMPure XP beads 47 Step 5. Add ‘A’ Bases to the 3' end of the DNA fragments 48 Step 6. Purify the sample using Agencourt AMPure XP beads 49 Step 7. Ligate the paired-end adaptor 50 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing5 Contents Step 8. Purify the sample using Agencourt AMPure XP beads Step 9. Amplify adaptor-ligated library 52 Step 10. Purify the sample with Agencourt AMPure XP beads Step 11. Assess quality and quantity 55 4 Hybridization 54 59 Step 1. Hybridize the library 62 Step 2. Prepare magnetic beads 68 Step 3. Select hybrid capture with SureSelect 5 51 69 Addition of Index Tags by Post-Hybridization Amplification 71 Step 1. Amplify the captured library to add index tags 72 Step 2. Purify the sample using Agencourt AMPure XP beads 76 Step 3. Assess quality 77 Step 4. Assess the quantity of each index-tagged library by QPCR (optional) 80 Step 5. Pool samples for Multiplexed Sequencing 81 Step 6. Prepare sample for cluster amplification 82 6 Reference 83 SureSelect Reagent Kit Content 84 Other Reagent Kits Content 86 SureSelectXT Indexes for Illumina 87 Alternative Capture Equipment Combinations 6 88 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 1 Before You Begin Procedural Notes 8 Safety Notes 8 Required Reagents 9 Optional Reagents 11 Required Equipment 12 Optional Equipment 13 Make sure you have the most current protocol. Go to genomics.agilent.com and search for G7530-90000. Make sure you read and understand the information in this chapter and have the necessary equipment and reagents listed before you start an experiment. NOTE This protocol differs from the Illumina Multiplexed Paired-End sequencing manual and other SureSelect protocols at several steps. Pay close attention to the primers used for each amplification step and the blocking agents used during hybridization. NOTE Agilent cannot guarantee the use of the SureSelect Target Enrichment kits with non-Agilent protocols nor provide technical support for non-Agilent protocols to process samples for enrichment. 7 1 Before You Begin Procedural Notes Procedural Notes • To prevent contamination of reagents by nucleases, always wear powder-free laboratory gloves and use dedicated solutions and pipettors with nuclease-free aerosol-resistant tips. • Maintain a clean work area. • Do not mix stock solutions and reactions containing gDNA on a vortex mixer. Instead, gently tap the tube with your finger to mix the sample. • When preparing frozen reagent stock solutions for use: 1 Thaw the aliquot as rapidly as possible without heating above room temperature. 2 Mix briefly on a vortex mixer, then spin in a centrifuge for 5 to 10 seconds to drive the contents off of walls and lid. 3 Store on ice or in a cold block until use. • In general, follow Biosafety Level 1 (BL1) safety rules. Safety Notes CAUTION 8 Wear appropriate personal protective equipment (PPE) when working in the laboratory. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Before You Begin Required Reagents 1 Required Reagents Table 1 Required Reagents for Library Prep and Post-Hybridization Amplification Description Vendor and part number For use with 2100 Bioanalyzer: DNA 1000 Kit Agilent p/n 5067-1504 High Sensitivity DNA Kit Agilent p/n 5067-4626 QPCR NGS Library Quantification Kit (Illumina GA) Agilent p/n G4880A or equivalent For use with 2200 TapeStation System: D1000 ScreenTape Agilent p/n 5067-5582 D1000 Reagents Agilent p/n 5067-5583 High Sensitivity D1000 ScreenTape Agilent p/n 5067-5584 High Sensitivity D1000 Reagents Agilent p/n 5067-5585 Herculase II Fusion DNA Polymerase (includes dNTP mix and 5x Buffer) 200 reactions (processes 100 XT libraries) 400 reactions Agilent p/n 600677 p/n 600679 Nuclease-free Water (not DEPC-treated) Ambion Cat #AM9930 Agencourt AMPure XP Kit 5 mL 60 mL 450 mL Beckman Coulter Genomics p/n A63880 p/n A63881 p/n A63882 1X Low TE Buffer (10 mM Tris-HCl (pH 8.0), 0.1 mM EDTA) Life Technologies p/n 12090-015 or equivalent Qubit dsDNA HS Assay Kit or Life Technologies p/n Q32851 Qubit dsDNA BR Assay Kit 100 assays, 2-1000 ng 500 assays, 2-1000 ng 1000 assays, 2-1000 ng Life Technologies p/n Q32850 Life Technologies p/n Q32853 Life Technologies p/n Q33130 Qubit assay tubes Life Technologies p/n Q32856 Buffer EB (10mM Tris-Cl, ph 8.5) Qiagen p/n 19086 Ethanol, 100% for molecular biology Sigma-Aldrich p/n E7023 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 9 1 Before You Begin Required Reagents SureSelect Reagent Kit* Table 2 Reagent Kits 16 Reactions 96 Reactions 480 Reactions Reagent Kit, HSQ G9611A G9611B G9611C SureSelectXT Reagent Kit, MSQ G9612A G9612B G9612C SureSelect XT * SureSelect reagents must be used within one year of receipt. SureSelect Capture Library (select one)* Table 3 10 Capture Libraries 16 Reactions 96 Reactions 480 Reactions SureSelectXT Focused Exome 5190-7787 5190-7788 SureSelectXT Focused Exome Plus 1 5190-7790 5190-7791 SureSelectXT Clinical Research Exome 5190-7338 5190-7339 SureSelectXT Human All Exon V5 5190-6208 5190-6209 SureSelectXT Human All Exon V5+UTRs 5190-6213 5190-6214 SureSelectXT Human All Exon V5+lncRNA 5190-6446 5190-6447 SureSelectXT Human All Exon V5 Plus 5190-6211 5190-6212 SureSelectXT Human All Exon V4 5190-4631 5190-4632 5190-4634 SureSelectXT Human All Exon V4+UTRs 5190-4636 5190-4637 5190-4639 SureSelectXT Mouse All Exon 5190-4641 5190-4642 5190-4644 SureSelectXT Inherited Disease 5190-7518 5190-7519 SureSelectXT Inherited Disease Plus 5190-7521 5190-7522 SureSelectXT DNA Kinome 5190-4646 5190-4647 5190-4649 SureSelectXT X-chromosome 5190-4651 5190-4652 5190-4653 SureSelectXT Custom 1 kb up to 499 Kb 5190-4806 5190-4807 5190-4809 (reorder) 5190-4811 5190-4812 5190-4814 SureSelectXT Custom 0.5 Mb up to 2.9 Mb 5190-4816 5190-4817 5190-4819 (reorder) 5190-4821 5190-4822 5190-4824 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Before You Begin Optional Reagents Table 3 1 SureSelect Capture Library (select one)* (Continued) Capture Libraries 16 Reactions 96 Reactions 480 Reactions SureSelectXT Custom 3 Mb up to 5.9 Mb 5190-4826 5190-4827 5190-4829 (reorder) 5190-4831 5190-4832 5190-4834 SureSelectXT Custom 6 Mb up to 11.9 Mb 5190-4836 5190-4837 5190-4839 (reorder) 5190-4841 5190-4842 5190-4844 SureSelectXT Custom 12 Mb up to 24 Mb 5190-4896 5190-4897 5190-4899 (reorder) 5190-4901 5190-4902 5190-4904 * SureSelect capture libraries must be used within one year of receipt. Table 4 Required Reagents for Hybridization Description Vendor and part number Dynabeads MyOne Streptavidin T1 Life Technologies 2 mL 10 mL 100 mL Cat #65601 Cat #65602 Cat #65603 Nuclease-free Water (not DEPC-treated) Ambion Cat #AM9930 Optional Reagents Table 5 Optional Reagents Description Vendor and part number Ethylene glycol American Bioanalytical p/n AB00455 Tween 20 Sigma-Aldrich p/n P9416-50ML SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 11 1 Before You Begin Required Equipment Required Equipment Table 6 Required Equipment for Library Prep and Post-Hybridization Amplification Description Vendor and part number 2100 Bioanalyzer Agilent p/n G2938C or 2200 TapeStation System Agilent p/n G2964AA or G2965AA Mx3005P Real-Time PCR System Agilent p/n 401449 or equivalent Thermal cycler Agilent SureCycler, Life Technologies Veriti Thermal Cycler, BioRad (MJ Research) DNA Engine PTC-200, or equivalent Covaris Sample Preparation System, S-series or E-series model Covaris Covaris microTUBE with AFA fiber and snap cap Covaris p/n 520045 Microcentrifuge Eppendorf Microcentrifuge Model 5417C or equivalent 1.5-mL LoBind Tube Eppendorf p/n 022431021 or equivalent Qubit Fluorometer Life Technologies p/n Q32857 Dynal DynaMag-2 magnetic stand Life Technologies p/n 123-21D or equivalent P10, P20, P200 and P1000 pipettes Pipetman P10, P20, P200, P1000 or equivalent Vacuum concentrator Savant SpeedVac or equivalent Ice bucket Powder-free gloves PCR tubes, strips, or plates Sterile, nuclease-free aerosol barrier pipette tips Timer Vortex mixer Heat block at 37°C 12 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Before You Begin Optional Equipment Table 7 1 Required Equipment for Hybridization Description Vendor and part number Mx3000P/Mx3005P 96-well tube plates Agilent p/n 410088 or equivalent Mx3000P/Mx3005P optical strip caps Agilent p/n 401425 or equivalent MicroAmp Clear Adhesive Film Life Technologies p/n 4306311 BD Clay Adams Nutator Mixer BD Diagnostics p/n 421105 or equivalent Dynal DynaMag-2 magnetic stand Life Technologies p/n 123-21D or equivalent P10, P20, P200 and P1000 pipettes Pipetman P10, P20, P200, P1000 or equivalent Pipet-Light Multichannel Pipette, 12 channels Rainin p/n L12-20 or equivalent PCR tubes, strips, or plates Sterile, nuclease-free aerosol barrier pipette tips Thermal cycler Agilent SureCycler, Life Technologies Veriti Thermal Cycler, BioRad (MJ Research) DNA Engine PTC-200, or equivalent Timer Vortex mixer Water bath or heat block set to 65°C Optional Equipment Table 8 Optional Equipment for Hybridization Description Vendor and part number Tube-strip capping tool Agilent p/n 410099 PlateLoc Thermal Microplate Sealer and Peelable Aluminum Seal Agilent p/n G5402A and Agilent p/n 24210-001 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 13 This page intentionally left blank. 14 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 2 Sample Preparation (3 µg DNA Samples) Step 1. Shear DNA 19 Step 2. Purify the sample using Agencourt AMPure XP beads Step 3. Assess quality (optional) 22 Step 4. Repair the ends 25 Step 5. Purify the sample using Agencourt AMPure XP beads Step 6. Add ‘A’ Bases to the 3' end of the DNA fragments 27 Step 7. Purify the sample using Agencourt AMPure XP beads Step 8. Ligate the paired-end adaptor 29 Step 9. Purify the sample using Agencourt AMPure XP beads Step 10. Amplify adaptor-ligated library 31 Step 11. Purify the sample with Agencourt AMPure XP beads Step 12. Assess quality and quantity 35 21 26 28 30 34 This chapter contains instructions for prepped library production specific to the Illumina paired-read sequencing platform. For each sample to be sequenced, individual library preparations, hybridizations, and captures are performed. The samples are then tagged by PCR with an index (barcode) sequence. Depending on the target size of the SureSelect capture, up to 16 samples can be pooled and sequenced in a single lane using Illumina multiplex index tags. CAUTION This protocol contains an option for 3-µg DNA samples (standard input) and an option for 200-ng DNA samples (low input). Make sure you follow the steps in the appropriate chapter. 15 The steps in this chapter differ from the Illumina protocol in the use of the Covaris system for gDNA shearing, smaller target shear size, elimination of size selection by gel purification, and implementation of AMPure XP beads for all purification steps, and primers used for PCR. Refer to the Illumina protocol Preparing Samples for Multiplexed Paired-End Sequencing (p/n 1005361 Rev. C) for more information. NOTE Make sure genomic DNA samples are of high quality with an OD 260/280 ratio ranging from 1.8 to 2.0. Use the Qubit system to quantify genomic DNA before library preparation. Sample Preparation (3 µg DNA Samples) 2 Genomic DNA Sample 1, 2…n Shear DNA fragments with a base pair peak of 150 to 200 bp Repair ends Blunt-ended fragments with 5'-phosphorylated ends Add Klenow and dATP 3'-dA overhang Ligate indexing-specific adaptors Genomic Locations Adaptor-modified ends Bait Design in eArray SureSelect Capture Library AMPure XP bead purification Removal of unligated adaptors PCR with SureSelect Primer and SureSelect Pre-capture Reverse PCR primers Prepped Library Library Hybridization (1 per sample) 16 or 24 hours at 65°C Hybrid Capture Selection Magnetic bead selection Amplification and Index Tagging PCR and purification Quality Assessment of each indexed sample Bioanalyzer and Quantification by QPCR Pool samples 1, 2...n Sequencing Figure 1 Overall sequencing sample preparation workflow. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 17 Table 10 Overview and time requirements Step Time Illumina Prepped library Production 1 day Library Hybridization 16 or 24 hours Bead preparation 30 minutes Capture Selection and Washing 2 hours DNA purification 30 minutes Post-Hybridization Amplification 1 hour PCR purification 30 minutes Bioanalyzer QC and QPCR 2 to 3 hours Pool indexed samples by mass < 1 hour Sample Preparation (3 µg DNA Samples) Step 1. Shear DNA 2 Step 1. Shear DNA For each DNA sample to be sequenced, prepare 1 library. 1 Use the Qubit dsDNA Assay to determine the concentration of your gDNA sample. Make sure the gDNA is of high quality (non-degraded, A260/A280 is 1.8 to 2.0). Follow the instructions for the instrument. 2 Set up the Covaris instrument. a Check that the water in the Covaris tank is filled with fresh deionized water to fill line level 12 on the graduated fill line label. b Check that the water covers the visible glass part of the tube. c Set the chiller temperature to between 2°C to 5°C to ensure that the temperature reading in the water bath displays 5°C. d Optional. Supplement the circulated water chiller with ethylene glycol to 20% volume to prevent freezing. e On the instrument control panel, push the Degas button. Degas the instrument for least 30 minutes before use. Refer to the Covaris instrument user guide. 3 Dilute 3 μg of high-quality gDNA with 1X Low TE Buffer in a 1.5-mL LoBind Tube to a total volume of 130 μL. 4 Put a Covaris microTube into the loading and unloading station. Keep the cap on the tube. 5 Use a tapered pipette tip to slowly transfer the 130 μL of DNA sample through the pre-split septa. Be careful not to introduce a bubble into the bottom of the tube. 6 Secure the microTube in the tube holder and shear the DNA with the settings in Table 11 or Table 12. The target peak for base pair size is 150 to 200 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 19 Table 11 Shear settings for Covaris instruments that use SonoLab 7 or newer Setting Value Duty Factor 10% Peak Incident Power (PIP) 175 Cycles per Burst 200 Treatment Time 360 seconds Bath Temperature 4° to 8° C Table 12 Shear settings for Covaris instruments that use SonoLab software previous to SonoLab 7 Setting Value Duty Cycle 10% Intensity 5 Cycles per Burst 200 Time 6 cycles of 60 seconds each Set Mode Frequency sweeping Temperature 4° to 7° C 7 Put the Covaris microTube back into the loading and unloading station. 8 While keeping the snap-cap on, insert a pipette tip through the pre-split septa, then slowly remove the sheared DNA. 9 Transfer the sheared DNA into a new 1.5-mL LoBind Tube. Sample Preparation (3 µg DNA Samples) Step 2. Purify the sample using Agencourt AMPure XP beads 2 Step 2. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 180 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the sheared DNA library (~130 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 50 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove approximately 50 μL of the supernatant to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 21 Step 3. Assess quality (optional) Quality assessment can be done with either the 2100 Bioanalyzer instrument or the 2200 TapeStation. 2100 Bioanalyzer System with DNA 1000 Assay For the Standard Input option, use the DNA 1000 Assay. 1 Check that the 2100 Bioanalyzer electrodes have been cleaned as instructed in the reagent kit guide. 2 Open the Agilent 2100 Expert Software (version B.02.02 or higher), turn on the 2100 Bioanalyzer and check communication. 3 Prepare the chip, samples and ladder as instructed in the reagent kit guide. 4 Load the prepared chip into the 2100 Bioanalyzer and start the run within five minutes after preparation. 5 Within the instrument context, choose the appropriate assay from the drop down list. 6 Start the run. Enter sample names and comments in the Data and Assay context. 7 Verify the results. Check that the electropherogram shows a distribution with a peak height between 150 to 200 bp. Sample Preparation (3 µg DNA Samples) Step 3. Assess quality (optional) Figure 2 2 Analysis of sheared DNA using a DNA 1000 Bioanalyzer assay. The electropherogram shows a distribution with a peak size between 150 to 200 bp. 2200 TapeStation and D1000 ScreenTape You can use the 2200 TapeStation for rapid analysis of multiple samples. Use the D1000 ScreenTape and D1000 Reagents. For more information to do this step, see the Agilent 2200 TapeStation User Manual. 1 Prepare the TapeStation samples as instructed in the Agilent 2200 TapeStation User Manual. Use 1 μL of each sheared DNA sample diluted with 3 μL of D1000 sample buffer for the analysis. CAUTION Make sure that you thoroughly mix the combined DNA and D1000 sample buffer on a vortex mixer for 5 seconds or more for accurate quantitation. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 23 2 Load the sample plate or tube strips from step 1, the D1000 ScreenTape, and loading tips into the 2200 TapeStation as instructed in the Agilent 2200 TapeStation User Manual. Start the run. 3 Verify that the electropherogram shows an average DNA fragment size of about 185 bp. A sample electropherogram is shown in Figure 3. Stopping Point If you do not continue to the next step, seal the sheared DNA sample plate and store at 4°C overnight or at –20°C for prolonged storage. Figure 3 Analysis of sheared DNA using the 2200 TapeStation with a D1000 ScreenTape. The electropherogram shows an average DNA fragment size between 150 to 200 bp. Sample Preparation (3 µg DNA Samples) Step 4. Repair the ends 2 Step 4. Repair the ends To process multiple samples, prepare master mixes with overage at each step, without the DNA sample. Master mixes for preparation of 12 samples (including excess) are shown in each table as an example. Use the SureSelect Library Prep Kit, ILM. Prepare the master mix on ice. 1 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 13. Mix well on a vortex mixer. b Add 52 μL of the reaction mix to each well or tube. c Add 48 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. 2 Incubate in a thermal cycler for 30 minutes at 20°C. Do not use a heated lid. If the heated lid of your thermal cycler cannot be turned off, incubate the sample with lid open. Table 13 End Repair Mix Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 35.2 µL 440 µL 10× End Repair Buffer (clear cap) 10 µL 125 µL dNTP Mix (green cap) 1.6 µL 20 µL T4 DNA Polymerase (purple cap) 1 µL 12.5 µL Klenow DNA Polymerase (yellow cap) 2 µL 25 µL T4 Polynucleotide Kinase (orange cap) 2.2 µL 27.5 µL Total Volume 52 µL 650 µL (52 µL/sample) SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 25 Step 5. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 180 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the end-repaired DNA library (~100 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 32 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. Remove the supernatant (~32 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. Sample Preparation (3 µg DNA Samples) Step 6. Add ‘A’ Bases to the 3' end of the DNA fragments 2 Step 6. Add ‘A’ Bases to the 3' end of the DNA fragments Use the SureSelect Library Prep Kit, ILM. 1 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 14. Mix well on a vortex mixer. b Add 20 μL of the reaction mix to each well or tube. c Add 30 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. Table 14 Adding “A” Bases Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 11 µL 137.5 µL 10× Klenow Polymerase Buffer (blue cap) 5 µL 62.5 µL dATP (green cap) 1 µL 12.5 µL Exo(-) Klenow (red cap) 3 µL 37.5 µL Total Volume 20 µL 250 µL (20 µL/sample) 2 Incubate in a thermal cycler for 30 minutes at 37°C. If you use a heated lid, make sure that the lid temperature does not exceed 50°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 27 Step 7. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the A-tailed DNA library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 15 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~15 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. 14 Proceed immediately to the next step, “Step 8. Ligate the paired-end adaptor”. Sample Preparation (3 µg DNA Samples) Step 8. Ligate the paired-end adaptor 2 Step 8. Ligate the paired-end adaptor This step uses a 10:1 molar ratio of adaptor to genomic DNA insert, based on a starting quantity of 3 μg of DNA before shearing. Use the SureSelect Library Prep Kit, ILM. 1 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 15. b Add 37 μL of the reaction mix to each well or tube. c Add 13 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. Table 15 Ligation master mix Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 15.5 µL 193.75 µL 5× T4 DNA Ligase Buffer 10 µL 125 µL SureSelect Adaptor Oligo Mix (brown cap) 10 µL 125 µL T4 DNA Ligase (red cap) 1.5 µL 18.75 µL Total Volume 37 µL 462.5 µL (37 µL/sample) 2 Incubate for 15 minutes at 20°C on a thermal cycler. Do not use a heated lid. Stopping Point If you do not continue to the next step, store the samples at -20°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 29 Step 9. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the ligated library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes until the residual Ethanol is completely evaporated. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 32 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~32 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. Sample Preparation (3 µg DNA Samples) Step 10. Amplify adaptor-ligated library 2 Step 10. Amplify adaptor-ligated library Use reagents from these kits: • SureSelect Library Prep Kit, ILM • SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2 • Herculase II Fusion DNA Polymerase (Agilent) This protocol uses half of the adaptor-ligated fragments for amplification. The remainder can be saved at -20°C for future use, if needed. CAUTION To avoid cross-contaminating libraries, set up PCR reactions (all components except the library DNA) in a dedicated clean area or PCR hood with UV sterilization and positive air flow. 1 Prepare reaction mix and DNA sample: a Prepare the reaction mix in Table 16, on ice. Mix well on a vortex mixer. b Add 35 μL of the reaction mix to each well or tube. c Add 15 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 31 Table 16 Components for PCR mix Reagent Volume for 1 reaction Volume for 12 reactions (includes excess) Nuclease-free Water 21 μL 262.5 μL SureSelect Primer (brown cap)* 1.25 µL 15.625 µL SureSelect ILM Indexing Pre Capture PCR Reverse Primer (clear cap)† 1.25 µL 15.625 µL 5× Herculase II Rxn Buffer (clear cap)‡ 10 μL 125 μL 0.5 μL 6.25 μL 1 μL 12.5 μL 35 μL 437.5 µL (35 µL/reaction) 100 mM dNTP Mix (green cap)‡ Herculase II Fusion DNA Polymerase (red cap)‡ Total * Included in the SureSelect Library Prep Kit, ILM. † Included in the SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2. ‡ Included in the Herculase II Fusion DNA Polymerase (Agilent) kit. Do not use the buffer or dNTP mix from any other kit. 2 Run the program in Table 17 in a thermal cycler. Table 17 PCR program Step Temperature Time Step 1 98°C 2 minutes Step 2 98°C 30 seconds Step 3 65°C 30 seconds Step 4 72°C 1 minute Step 5 Repeat Step 2 through Step 4 for a total of 4 to 6 times. Step 6 72°C 10 minutes Step 7 4°C Hold Sample Preparation (3 µg DNA Samples) Step 10. Amplify adaptor-ligated library NOTE 2 Different library preparations can produce slightly different results, based on varying DNA quality. In most cases, 5 cycles will produce an adequate yield for subsequent capture without introducing bias or non-specific products. If yield is too low or non-specific high molecular weight products are observed, adjust the number of cycles accordingly with the remaining extra library template. As an alternative, you can prepare one PCR master mix as outlined in Table 16. Split the master mix into three small-scale 10-µL PCR reactions and run for 4, 5 or 6 cycles. Clean these PCR reactions using the AMPure XP protocol outlined in “Step 2. Purify the sample using Agencourt AMPure XP beads” with these modifications: Use 30 µL of AMPure XP beads and elute with 20 µL of Nuclease-free Water. Run these cleaned samples on a DNA1000 chip on the Bioanalyzer, as described in “Step 3. Assess quality (optional)”. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 33 Step 11. Purify the sample with Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the amplified library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 30 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~30 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. Sample Preparation (3 µg DNA Samples) Step 12. Assess quality and quantity 2 Step 12. Assess quality and quantity Quality assessment can be done with either the 2100 Bioanalyzer instrument or the 2200 TapeStation. 2100 Bioanalyzer System and DNA 1000 Assay 1 Check that the 2100 Bioanalyzer electrodes have been cleaned as instructed in the reagent kit guide. 2 Open the Agilent 2100 Expert Software (version B.02.02 or higher), turn on the 2100 Bioanalyzer and check communication. 3 Prepare the chip, samples and ladder as instructed in the reagent kit guide. 4 Load the prepared chip into the 2100 Bioanalyzer and start the run within five minutes after preparation. 5 Within the instrument context, choose the appropriate assay from the drop down list. 6 Start the run. Enter sample names and comments in the Data and Assay context. 7 Verify the results. Check that the electropherogram shows a distribution with a peak size approximately 225 to 275 bp. Measure the concentration of the library by integrating under the peak. Figure 4 Analysis of amplified library DNA using a DNA 1000 assay. The electropherogram shows a single peak in the size range of 225 to 275 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 35 2200 TapeStation and D1000 ScreenTape You can use the 2200 TapeStation to analyze the amplified libraries. Use the D1000 ScreenTape and D1000 Reagents. For more information to do this step, see the Agilent 2200 TapeStation User Manual. 1 Prepare the TapeStation samples as instructed in the Agilent 2200 TapeStation User Manual. Use 1 μL of each amplified library DNA sample diluted with 3 μL of D1000 sample buffer for the analysis. CAUTION Make sure that you thoroughly mix the combined DNA and D1000 sample buffer on a vortex mixer for 5 seconds or more for accurate quantitation. 2 Load the sample plate or tube strips from step 1, the D1000 ScreenTape, and loading tips into the 2200 TapeStation as instructed in the Agilent 2200 TapeStation User Manual. Start the run. 3 Verify that the electropherogram shows a distribution with a peak size approximately 225 to 275 bp. A sample electropherogram is shown in Figure 5. Stopping Point If you do not continue to the next step, seal the sheared DNA sample plate and store at 4°C overnight or at –20°C for prolonged storage. Sample Preparation (3 µg DNA Samples) Step 12. Assess quality and quantity Figure 5 2 Analysis of amplified library DNA using the 2200 TapeStation with a D1000 ScreenTape. The electropherogram shows a single peak in the size range of 225 to 275 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 37 This page intentionally left blank. 38 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 3 Sample Preparation (200 ng DNA Samples) Step 1. Shear DNA 43 Step 2. Assess quality (optional) 45 Step 3. Repair the ends 46 Step 4. Purify the sample using Agencourt AMPure XP beads Step 5. Add ‘A’ Bases to the 3' end of the DNA fragments 48 Step 6. Purify the sample using Agencourt AMPure XP beads Step 7. Ligate the paired-end adaptor 50 Step 8. Purify the sample using Agencourt AMPure XP beads Step 9. Amplify adaptor-ligated library 52 Step 10. Purify the sample with Agencourt AMPure XP beads Step 11. Assess quality and quantity 55 47 49 51 54 This chapter contains instructions for prepped library production specific to the Illumina paired-read sequencing platform. For each sample to be sequenced, individual library preparations, hybridizations, and captures are performed. The samples are then tagged by PCR with an index (barcode) sequence. Depending on the target size of the SureSelect capture, up to 16 samples can be pooled and sequenced in a single lane using Illumina multiplex index tags. CAUTION This protocol contains an option for 3-µg DNA samples (standard input) and an option for 200-ng DNA samples (low input). Make sure you follow the steps in the appropriate chapter. 39 The steps in this chapter differ from the Illumina protocol in the use of the Covaris system for gDNA shearing, smaller target shear size, elimination of size selection by gel purification, and implementation of AMPure XP beads for all purification steps, and primers used for PCR. Refer to the Illumina protocol Preparing Samples for Multiplexed Paired-End Sequencing (p/n 1005361 Rev. C) for more information. NOTE Make sure genomic DNA samples are of high quality with an OD 260/280 ratio ranging from 1.8 to 2.0. Use the Qubit system to quantify genomic DNA before library preparation. Sample Preparation (200 ng DNA Samples) 3 Genomic DNA Sample 1, 2…n Shear DNA fragments with a base pair peak of 150 to 200 bp Repair ends Blunt-ended fragments with 5'-phosphorylated ends Add Klenow and dATP 3'-dA overhang Ligate diluted indexingspecific adaptors Genomic Locations Adaptor-modified ends Bait Design in eArray SureSelect Capture Library AMPure XP bead purification Removal of unligated adaptors PCR with SureSelect Primer and SureSelect Pre-capture Reverse PCR primers Prepped Library Library Hybridization (1 per sample) 16 or 24 hours at 65°C Hybrid Capture Selection Magnetic bead selection Amplification and Index Tagging PCR and purification Quality Assessment of each indexed sample Bioanalyzer and Quantification by QPCR Pool samples 1, 2...n Sequencing Figure 6 Overall sequencing sample preparation workflow. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 41 Table 18 Overview and time requirements Step Time Illumina Prepped library Production 1 day Library Hybridization 16 or 24 hours Bead preparation 30 minutes Capture Selection and Washing 2 hours DNA purification 30 minutes Post-Hybridization Amplification 1 hour PCR purification 30 minutes Bioanalyzer QC and QPCR 2 to 3 hours Pool indexed samples by mass < 1 hour Sample Preparation (200 ng DNA Samples) Step 1. Shear DNA 3 Step 1. Shear DNA For each DNA sample to be sequenced, prepare 1 library. 1 Use the Qubit dsDNA Assay to determine the concentration of your gDNA sample. Make sure the gDNA is of high quality (non-degraded, A260/A280 is 1.8 to 2.0). Follow the instructions for the instrument. 2 Set up the Covaris instrument. a Check that the water in the Covaris tank is filled with fresh deionized water to fill line level 12 on the graduated fill line label. b Check that the water covers the visible glass part of the tube. c Set the chiller temperature to between 2°C to 5°C to ensure that the temperature reading in the water bath displays 5°C. d Optional. Supplement the circulated water chiller with ethylene glycol to 20% volume to prevent freezing. e On the instrument control panel, push the Degas button. Degas the instrument for least 30 minutes before use. Refer to the Covaris instrument user guide. 3 Dilute 200 ng of high-quality gDNA with 1X Low TE Buffer in a 1.5-mL LoBind Tube for a total of 50 μL. 4 Put a Covaris microTube into the loading and unloading station. Keep the cap on the tube. 5 Use a tapered pipette tip to slowly transfer the 50 μL of DNA sample through the pre-split septa. Be careful not to introduce a bubble into the bottom of the tube. 6 Secure the microTube in the tube holder and shear the DNA with the settings in Table 19 or Table 20. The target peak for base pair size is 150 to 200 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 43 Table 19 Shear settings for Covaris instruments that use SonoLab 7 or newer Setting Value Duty Factor 10% Peak Incident Power (PIP) 175 Cycles per Burst 200 Treatment Time 360 seconds Bath Temperature 4° to 8° C Table 20 Shear settings for Covaris instruments that use SonoLab software previous to SonoLab 7 Setting Value Duty Cycle 10% Intensity 5 Cycles per Burst 200 Time 6 cycles of 60 seconds each Set Mode Frequency sweeping Temperature 4° to 7° C 7 Put the Covaris microTube back into the loading and unloading station. 8 While keeping the snap-cap on, insert a pipette tip through the pre-split septa, then slowly remove the sheared DNA. 9 Transfer the sheared DNA into a new 1.5-mL LoBind Tube. Sample Preparation (200 ng DNA Samples) Step 2. Assess quality (optional) 3 Step 2. Assess quality (optional) Quality assessment can be done with the 2100 Bioanalyzer instrument. For the 200-ng option, use the High Sensitivity DNA assay. 1 Check that the 2100 Bioanalyzer electrodes have been cleaned as instructed in the reagent kit guide. 2 Open the Agilent 2100 Expert Software (version B.02.02 or higher), turn on the 2100 Bioanalyzer and check communication. 3 Prepare the chip, samples and ladder as instructed in the reagent kit guide. 4 Load the prepared chip into the 2100 Bioanalyzer and start the run within five minutes after preparation. 5 Within the instrument context, choose the appropriate assay from the drop down list. 6 Start the run. Enter sample names and comments in the Data and Assay context. 7 Verify the results. Check that the electropherogram shows a distribution with a peak height between 120 to 150 bp. Figure 7 Analysis of sheared DNA using a High Sensitivity DNA assay. The electropherogram shows a distribution with a peak size between 120 to 150 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 45 Step 3. Repair the ends To process multiple samples, prepare master mixes with overage at each step, without the DNA sample. Master mixes for preparation of 12 samples (including excess) are shown in each table as an example. Use the SureSelect Library Prep Kit, ILM. Prepare the master mix on ice. 1 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 21. Mix well on a vortex mixer. b Add 52 μL of the reaction mix to each well or tube. c Add 48 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. 2 Incubate in a thermal cycler for 30 minutes at 20°C. Do not use a heated lid. If the heated lid of your thermal cycler cannot be turned off, incubate the sample with lid open. Table 21 End Repair Mix Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 35.2 µL 440 µL 10× End Repair Buffer (clear cap) 10 µL 125 µL dNTP Mix (green cap) 1.6 µL 20 µL T4 DNA Polymerase (purple cap) 1 µL 12.5 µL Klenow DNA Polymerase (yellow cap) 2 µL 25 µL T4 Polynucleotide Kinase (orange cap) 2.2 µL 27.5 µL Total Volume 52 µL 650 µL (52 µL/sample) Sample Preparation (200 ng DNA Samples) Step 4. Purify the sample using Agencourt AMPure XP beads 3 Step 4. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 180 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the end-repaired DNA library (~100 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 32 μL Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. Remove the supernatant (~32 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 47 Step 5. Add ‘A’ Bases to the 3' end of the DNA fragments Use the SureSelect Library Prep Kit, ILM. 1 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 22. Mix well on a vortex mixer. b Add 20 μL of the reaction mix to each well or tube. c Add 30 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. Table 22 Adding “A” Bases Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 11 µL 137.5 µL 10× Klenow Polymerase Buffer (blue cap) 5 µL 62.5 µL dATP (green cap) 1 µL 12.5 µL Exo(-) Klenow (red cap) 3 µL 37.5 µL Total Volume 20 µL 250 µL (20 µL/sample) 2 Incubate in a thermal cycler for 30 minutes at 37°C. If you use a heated lid, make sure that the lid temperature does not exceed 50°C. Sample Preparation (200 ng DNA Samples) Step 6. Purify the sample using Agencourt AMPure XP beads 3 Step 6. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the A-tailed DNA library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 15 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~15 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. 14 Proceed immediately to the next step, “Step 7. Ligate the paired-end adaptor”. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 49 Step 7. Ligate the paired-end adaptor Use the SureSelect Library Prep Kit, ILM. 1 Dilute SureSelect Adaptor Oligo Mix (brown cap) 1:10 in Nuclease-free Water immediately before use. Use the diluted Oligo mix in the next step. 2 Prepare reaction mix and DNA sample (prepare on ice): a Prepare the reaction mix in Table 23. b Add 37 μL of the reaction mix to each well or tube. c Add 13 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. Table 23 Ligation master mix Reagent Volume for 1 Library Volume for 12 Libraries (includes excess) Nuclease-free Water 15.5 µL 193.75 µL 5× T4 DNA Ligase Buffer 10 µL 125 µL Diluted SureSelect Adaptor Oligo Mix 10 µL 125 µL T4 DNA Ligase (red cap) 1.5 µL 18.75 µL Total Volume 37 µL 462.5 µL (37 µL/sample) 3 Incubate for 15 minutes at 20°C on a thermal cycler. Do not use a heated lid. Stopping Point If you do not continue to the next step, store the samples at -20°C. Sample Preparation (200 ng DNA Samples) Step 8. Purify the sample using Agencourt AMPure XP beads 3 Step 8. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the ligated library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes until the residual Ethanol is completely evaporated. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 32 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~32 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 51 Step 9. Amplify adaptor-ligated library Use reagents from these kits: • SureSelect Library Prep Kit, ILM • SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2 • Herculase II Fusion DNA Polymerase (Agilent) CAUTION To avoid cross-contaminating libraries, set up PCR reactions (all components except the library DNA) in a dedicated clean area or PCR hood with UV sterilization and positive air flow. 1 Prepare reaction mix and DNA sample: a Prepare the reaction mix in Table 24, on ice. Mix well on a vortex mixer. b Add 20 μL of the reaction mix to each well or tube. c Add 30 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples. Sample Preparation (200 ng DNA Samples) Step 9. Amplify adaptor-ligated library Table 24 3 Components for PCR mix Reagent Volume for 1 reaction Volume for 12 reactions (includes excess) Nuclease-free Water 6 μL 75 μL SureSelect Primer (brown cap)* 1.25 µL 15.625 µL SureSelect ILM Indexing Pre Capture PCR Reverse Primer (clear cap)† 1.25 µL 15.625 µL 5× Herculase II Rxn Buffer (clear cap)‡ 10 μL 125 μL 0.5 μL 6.25 μL 1 μL 12.5 μL 20 μL 250 µL (20 µL/reaction) 100 mM dNTP Mix (green cap)‡ Herculase II Fusion DNA Polymerase (red cap)‡ Total * Included in the SureSelect Library Prep Kit, ILM. † Included in the SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2. ‡ Included in the Herculase II Fusion DNA Polymerase (Agilent) kit. Do not use the buffer or dNTP mix from any other kit. 2 Run the program in Table 25 in a thermal cycler. Table 25 PCR program Step Temperature Time Step 1 98°C 2 minutes Step 2 98°C 30 seconds Step 3 65°C 30 seconds Step 4 72°C 1 minute Step 5 Repeat Step 2 through Step 4 for a total of 10 times. Step 6 72°C 10 minutes Step 7 4°C Hold SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 53 Step 10. Purify the sample with Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure XP beads to a 1.5-mL LoBind Tube, and add the amplified library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal result. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 step once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol completely evaporates. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 30 μL of Nuclease-free Water, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~30 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point If you do not continue to the next step, store the samples at -20°C. Sample Preparation (200 ng DNA Samples) Step 11. Assess quality and quantity 3 Step 11. Assess quality and quantity Quality assessment can be done with either the 2100 Bioanalyzer instrument or the 2200 TapeStation. 2100 Bioanalyzer System and DNA 1000 Assay 1 Check that the 2100 Bioanalyzer electrodes have been cleaned as instructed in the reagent kit guide. 2 Open the Agilent 2100 Expert Software (version B.02.02 or higher), turn on the 2100 Bioanalyzer and check communication. 3 Prepare the chip, samples and ladder as instructed in the reagent kit guide. 4 Load the prepared chip into the 2100 Bioanalyzer and start the run within five minutes after preparation. 5 Within the instrument context, choose the appropriate assay from the drop down list. 6 Start the run. Enter sample names and comments in the Data and Assay context. 7 Verify the results. Check that the electropherogram shows a distribution with a peak size approximately 225 to 275 bp. Measure the concentration of the library by integrating under the peak. Figure 8 Analysis of amplified prepped library DNA using a DNA 1000 assay. The electropherogram shows a single peak in the size range of 225 to 275 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 55 2200 TapeStation and D1000 ScreenTape You can use the 2200 TapeStation to analyze the amplified libraries. Use the D1000 ScreenTape and D1000 Reagents. For more information to do this step, see the Agilent 2200 TapeStation User Manual. 1 Prepare the TapeStation samples as instructed in the Agilent 2200 TapeStation User Manual. Use 1 μL of each amplified library DNA sample diluted with 3 μL of D1000 sample buffer for the analysis. CAUTION Make sure that you thoroughly mix the combined DNA and D1000 sample buffer on a vortex mixer for 5 seconds or more for accurate quantitation. 2 Load the sample plate or tube strips from step 1, the D1000 ScreenTape, and loading tips into the 2200 TapeStation as instructed in the Agilent 2200 TapeStation User Manual. Start the run. 3 Verify that the electropherogram shows a distribution with a peak size approximately 225 to 275 bp. A sample electropherogram is shown in Figure 9. Stopping Point If you do not continue to the next step, seal the sheared DNA sample plate and store at 4°C overnight or at –20°C for prolonged storage. Sample Preparation (200 ng DNA Samples) Step 11. Assess quality and quantity Figure 9 3 Analysis of amplified library DNA using the 2200 TapeStation with a D1000 ScreenTape. The electropherogram shows a single peak in the size range of 225 to 275 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 57 This page intentionally left blank. 58 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 4 Hybridization Step 1. Hybridize the library 62 Step 2. Prepare magnetic beads 68 Step 3. Select hybrid capture with SureSelect 69 This chapter describes the steps to combine the prepped library with the hybridization reagents, blocking agents and the SureSelect capture library. Each DNA library sample must be hybridized and captured individually prior to addition of the indexing tag by PCR. CAUTION The ratio of SureSelect capture library to prepped library is critical for successful capture. 59 4 Hybridization GENOMIC SAMPLE (Set of chromosomes) SureSelect™ Target Enrichment System Capture Process S¢EEcE3 Kit + GENOMIC SAMPLE (PREPPED) + SureSelect HYB BUFFER SureSelect BIOTINYLATED RNA LIBRARY “BAITS” Hybridization STREPTAVIDIN COATED MAGNETIC BEADS + Bead capture UNBOUND FRACTION DISCARDED Wash Beads and Digest RNA gyc`N§ <<¢c`ycE¦!U Sequencing ¢`goc!yooc`lU oNg¢c`ycE¦E<!gycE Figure 10 60 SureSelect Target Enrichment System Capture Process SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Hybridization 4 Refer to “SureSelect Reagent Kit Content” on page 84 for a complete content listing of each SureSelect Target Enrichment kit. CAUTION You must avoid evaporation from the small volumes of the capture during the 16 or 24 hour incubation. If you want to use a different combination of thermal cycler, lid temperature, plates or strips, and sealing method (strip caps or sealing tape), first test the conditions. Incubate 27 µL of SureSelect Hybridization Buffer (without DNA) at 65°C for 24 hours as a test. Include buffer in each well that you might use, including those in the center and those on the edges. Check that you do not get extensive evaporation. Evaporation should not exceed 3 to 4 µL. For a partial list of tested options showing minimal evaporation, refer to “Alternative Capture Equipment Combinations” on page 88. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 61 4 Hybridization Step 1. Hybridize the library Step 1. Hybridize the library For each sample library prepared, do one hybridization and capture. Do not pool samples at this stage. The hybridization reaction requires 750 ng of DNA with a maximum volume of 3.4 μL. 1 If the prepped library concentration is below 221 ng/μL, use a vacuum concentrator to concentrate the sample at 45°C. a Add the entire 30 μL of prepped library to an Eppendorf tube. Poke one or more holes in the lid with a narrow gauge needle. You can also break off the cap, cover with parafilm, and poke a hole in the parafilm. b Completely lyophilize. Use a vacuum concentrator on low heat (less than 45°C) to dehydrate. c Reconstitute with nuclease-free water to bring the final concentration to 221 ng/μL (or greater if sample recovery is of concern). Pipette up and down along the sides of the tube for optimal recovery. d Mix well on a vortex mixer and spin in a microfuge for 1 minute. 2 Optional. To test recovery after lyophilization, reconstitute the sample to greater than 221 ng/μL and check the concentration on a Bioanalyzer DNA 1000 chip. See “Step 12. Assess quality and quantity” on page 35. After quantitation, adjust the sample to 221 ng/μL. Alternatively, concentrate a 750 ng aliquot at 45°C down to 3.4 μL. If the sample dries up completely, resuspend in 3.4 μL of water and mix on a vortex mixer. If processing multiple samples, adjust to equivalent volumes before concentrating. 3 Mix the components in Table 26 at room temperature to prepare the hybridization buffer. 62 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Hybridization Step 1. Hybridize the library Table 26 4 Hybridization Buffer Reagent Volume for 1 Volume for 6 capture (µL), captures (µL), includes excess includes excess Volume for 12 captures (µL), includes excess SureSelect Hyb #1 (orange cap, or bottle) 25 125 250 SureSelect Hyb #2 (red cap) 1 5 10 SureSelect Hyb #3 (yellow cap) 10 50 100 SureSelect Hyb #4 (black cap, or bottle) 13 65 130 Total 49 (40 µL needed) 245 (40 µL/sample) 490 (40 µL/sample) 4 If precipitate forms, warm the hybridization buffer at 65°C for 5 minutes. 5 In a PCR plate, prepare the SureSelect capture library mix for target enrichment: a Keep capture library mix tubes on ice during preparation and until they are used in step 10. b For each sample, add the amount of SureSelect capture library as listed in Table 27, based on the Mb target size of your design. c Use nuclease-free water to prepare a dilution of the SureSelect RNase Block (purple cap) as listed in Table 27. Prepare enough RNase Block dilution for all samples, plus excess. d Add the amount of diluted SureSelect RNase Block (purple cap) listed in Table 27 to each capture library, and mix by pipetting. Table 27 SureSelect Capture Library. Capture Size Volume of SureSelect Library RNase Block Dilution (Parts RNase block: Parts water) Volume of RNase Block Dilution to Add 3.0 Mb 2 µL 1:9 (10%) 5 µL 3.0 Mb 5 µL 1:3 (25%) 2 µL SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 63 4 Hybridization Step 1. Hybridize the library 6 Mix the contents in Table 28 to make the correct amount of SureSelect Block mix for the number of samples used. Table 28 SureSelect Block Mix Reagent Volume for 1 reaction Volume for 12 reactions (includes excess) SureSelect Indexing Block #1 (green cap) 2.5 µL 31.25 µL SureSelect Block #2 (blue cap) 2.5 µL 31.25 µL SureSelect Indexing Block #3 (brown cap) 0.6 µL 7.5 µL Total 5.6 µL 70 µL 7 In a separate PCR plate, prepare the prepped library for target enrichment. a Add 3.4 μL of 221 ng/μL prepped library to the “B” row in the PCR plate. Put each sample into a separate well. b Add 5.6 μL of the SureSelect Block Mix to each well in row B. c Mix by pipetting up and down. d Seal the wells of row “B” with caps and put the PCR plate in the thermal cycler. Do not heat the Hybridization Buffer or capture library yet, only the prepped library with blockers. e Start the thermal cycler program in Table 29. Prepped Library Figure 11 64 Prepped library shown in red SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Hybridization Step 1. Hybridize the library Table 29 4 PCR program Step Temperature Time Step 1 95°C 5 minutes Step 2 65°C Hold 8 Use a heated lid on the thermal cycler at 105°C to hold the temperature of the plate on the thermal cycler at 65°C. CAUTION The lid of the thermal cycler is hot and can cause burns. Use caution when working near the lid. 9 Add the hybridization buffer to the PCR plate: a Maintain the plate at 65°C while you load 40 μL of hybridization buffer per well into the “A” row of the PCR plate. The number of wells filled in Row A is the number of libraries prepared. The example in Figure 12 is for 12 captures. Hybridization Buffer Prepped Library Figure 12 Hybridization buffer shown in blue b Seal the wells with strip caps. Use a capping tool to make sure the fit is tight. c Keep the plate at 65°C for a minimum of 5 minutes before you go to step 10. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 65 4 Hybridization Step 1. Hybridize the library 10 Add the capture library mix from step 5 to the PCR plate: a Add the capture library mix (7 μL) to the “C” row in the PCR plate. For multiple samples, use a multi-channel pipette to load the capture library mix into the “C” row in the PCR plate. Keep the plate at 65°C during this time. b Seal the wells with strip caps. Use a capping tool to make sure the fit is tight. c Incubate the samples at 65°C for 2 minutes. 11 Maintain the plate at 65°C while you use a multi-channel pipette to take 13 μL of Hybridization Buffer from the “A” row and add it to the SureSelect capture library mix contained in row “C” of the PCR plate for each sample. (See Figure 13.) step 11 step 12 Hybridization Buffer Prepped Library SureSelect Capture Library Figure 13 SureSelect Capture Library, or “Baits”, shown in Green 12 Maintain the plate at 65°C while you use a multi-channel pipette to transfer the entire contents of each prepped library mix in row “B” to the hybridization solution in row “C”. (See Figure 13.) Mix well by slowly pipetting up and down 8 to 10 times. The hybridization mixture is now 27 to 29 μL, depending on degree of evaporation during the preincubations. 13 Seal the wells with strip caps or double adhesive film. Make sure all wells are completely sealed. Use new adhesive seals or strip caps. The structural integrity of the seals and caps can be compromised during the previous incubation steps. 66 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Hybridization Step 1. Hybridize the library CAUTION 4 Wells must be adequately sealed to minimize evaporation, or your results can be negatively impacted. You can use the PlateLoc Thermal Microplate Sealer to minimize evaporation. If you use strip tubes, test for evaporation before you do the first experiment to make sure the tube/capping method is appropriate for the thermal cycler. Check that no more than 3 to 4 μL is lost to evaporation. 14 Incubate the hybridization mixture for 16 or 24 hours at 65°C with a heated lid at 105°C. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 67 4 Hybridization Step 2. Prepare magnetic beads Step 2. Prepare magnetic beads Use these reagents from the SureSelect Target Enrichment Kit Box #1: • SureSelect Binding Buffer • SureSelect Wash 2 1 Prewarm SureSelect Wash 2 at 65°C in a circulating water bath or heat block for use in “Step 3. Select hybrid capture with SureSelect”. 2 Vigorously resuspend the Dynabeads MyOne Streptavidin T1 on a vortex mixer. Magnetic beads settle during storage. 3 For each hybridization, add 50 μL of Dynabeads MyOne Streptavidin T1 to a 1.5-mL LoBind Tube. 4 Wash the beads: a Add 200 μL of SureSelect Binding Buffer. b Mix the beads on a vortex mixer for 5 seconds. c Put the tubes into a magnetic device, such as the Dynal magnetic separator (Life Technologies). d Remove and discard the supernatant. e Repeat step a through step d for a total of 3 washes. 5 Resuspend the beads in 200 μL of SureSelect Binding Buffer. 68 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Hybridization Step 3. Select hybrid capture with SureSelect 4 Step 3. Select hybrid capture with SureSelect Use these reagents from the SureSelect Target Enrichment Kit Box #1: • SureSelect Wash 1 • SureSelect Wash 2 1 Estimate and record the volume of hybridization that remained after 16 or 24 hour incubation. 2 Keep the PCR plate or tubes at 65°C in the PCR machine while you add the hybridization mixture directly from the thermal cycler to the bead solution. Invert the tube to mix 3 to 5 times. Excessive evaporation, such as when less than 20 μL remains after hybridization, can indicate suboptimal capture performance. See Table 43 on page 88 for tips to minimize evaporation. 3 Incubate the hybrid-capture/bead solution on a Nutator or equivalent for 30 minutes at room temperature. Make sure the sample is properly mixing in the tube. 4 Briefly spin in a centrifuge. 5 Separate the beads and buffer on a magnetic separator and remove the supernatant. 6 Resuspend the beads in 500 μL of SureSelect Wash 1 by mixing on a vortex mixer for 5 seconds. 7 Incubate the samples for 15 minutes at room temperature. Occasionally mix on a vortex mixer. 8 Briefly spin in a centrifuge. 9 Separate the beads and buffer on a magnetic separator and remove the supernatant. 10 Wash the beads: a Resuspend the beads in 500 μL of 65°C prewarmed SureSelect Wash 2 and mix on a vortex mixer for 5 seconds to resuspend the beads. b Incubate the samples for 10 minutes at 65°C in a recirculating water bath, heat block or equivalent. Occasionally mix on a vortex mixer. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 69 4 Hybridization Step 3. Select hybrid capture with SureSelect Do not use a tissue incubator. It cannot properly maintain temperature. c Briefly spin in a centrifuge. d Separate the beads and buffer on a magnetic separator and remove the supernatant. e Repeat step a through step d for a total of 3 washes. Make sure all of the wash buffer has been removed. 11 Mix the beads in 30 μL of nuclease-free water on a vortex mixer for 5 seconds to resuspend the beads. x NOTE 70 Captured DNA is retained on the streptavidin beads during the post-capture amplification step. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 5 Addition of Index Tags by Post-Hybridization Amplification Step 1. Amplify the captured library to add index tags 72 Step 2. Purify the sample using Agencourt AMPure XP beads 76 Step 3. Assess quality 77 Step 4. Assess the quantity of each index-tagged library by QPCR (optional) 80 Step 5. Pool samples for Multiplexed Sequencing 81 Step 6. Prepare sample for cluster amplification 82 This chapter describes the steps to add index tags by amplification, purify, assess quality and quantity of the libraries, dilute the sample appropriately for cluster amplification, and pool indexed samples for multiplexed sequencing. 71 5 Addition of Index Tags by Post-Hybridization Amplification Step 1. Amplify the captured library to add index tags Step 1. Amplify the captured library to add index tags Use reagents from: • Herculase II Fusion DNA Polymerase (Agilent) • SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2 • SureSelect Library Prep Kit, ILM CAUTION Do not use amplification enzymes other than Herculase II Fusion DNA Polymerase. Other enzymes have not been validated. CAUTION To avoid cross-contaminating libraries, set up PCR reactions (all components except the library DNA) in a dedicated clean area or PCR hood with UV sterilization and positive air flow. Prepare 1 amplification reaction for each hybrid capture. Include a negative no-template control. To see the nucleotide sequence in each of the index included in SureSelect reagent kits, see “SureSelectXT Indexes for Illumina” on page 87. 1 Prepare reaction mix and DNA samples: a Prepare the reaction mix in Table 30, on ice. Mix well on a vortex mixer. b Add 35 μL of the reaction mix to each well or tube. c Add 1 μL of the appropriate index PCR Primer Index 1 through Index 16 (clear caps) from the SureSelect Library Prep Kit, ILM to each well and mix by pipetting. 72 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Addition of Index Tags by Post-Hybridization Amplification Step 1. Amplify the captured library to add index tags 5 Use a different index primer for each sample to be sequenced in the same lane. Use Table 31 as a guide to determine the number of indexes to pool per sequencing lane. d Pipette each DNA sample up and down to make sure that the bead solution is homogeneous. e Use a pipette to add 14 μL of each DNA sample to each well or tube. Mix by pipetting. Change pipette tips between samples to avoid cross-contamination. If needed, store the remaining bead at -20°C for future use. Table 30 Herculase II Master Mix Reagent Volume for 1 reaction Volume for 12 reactions (includes excess) 22.5 µL 281.25 µL 10 µL 125 µL 1 µL 12.5 µL 0.5 µL 6.25 µL SureSelect ILM Indexing Post Capture Forward PCR Primer (orange cap)† 1 µL 12.5 µL Total 35 µL 437.5 µL (35 µL/reaction) Nuclease-free water 5× Herculase II Rxn Buffer (clear cap) * Herculase II Fusion DNA Polymerase (red cap)* 100 mM dNTP Mix (green cap)* * Included in the Herculase II Fusion DNA Polymerase (Agilent). Do not use the buffer or dNTP mix from any other kit. † Included in the SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2. Table 31 Sequencing data requirement guidelines Capture size Optimal sequencing output per index 1 kb up to 0.5 Mb 0.1 to 50 Mb* 0.5 Mb up to 2.9 Mb 50 to 290 Mb* 3 Mb up to 5.9 Mb 300 to 590 Mb* 6 Mb up to 11.9 Mb 600 to 1190 Mb* SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 73 5 Addition of Index Tags by Post-Hybridization Amplification Step 1. Amplify the captured library to add index tags Table 31 Sequencing data requirement guidelines Capture size Optimal sequencing output per index 12 Mb up to 24 Mb 1.2 to 2.4 Gb* Human All Exon v5 4 Gb Human All Exon v5 + UTRs 6 Gb Human All Exon 50 Mb 5 Gb Human DNA Kinome 320 Mb Mouse All Exon 5 Gb * For custom libraries, Agilent recommends analyzing 100× amount of sequencing data compared to the Capture Library size for each sample. Pool samples according to your expected sequencing output. 2 Put the tubes in a thermal cycler and run the program in Table 32. Store the unused bead-bound captured DNA samples at 4°C overnight, or at -20°C long-term. Table 32 PCR program Step Temperature Time Step 1 98°C 2 minutes Step 2 98°C 30 seconds Step 3 57°C 30 seconds Step 4 72°C 1 minute Step 5 74 • Repeat Step 2 through Step 4 for a total of 12 to 16 times. Step 6 72°C 10 minutes Step 7 4°C Hold SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Addition of Index Tags by Post-Hybridization Amplification Step 1. Amplify the captured library to add index tags 5 As with the pre-capture PCR amplification, minimize the number of PCR cycles used to enrich the captured DNA. The use of only half of the captured DNA for amplification lets you adjust the number of cycles by repeating the PCR if needed. Table 33 Number of cycles Capture Size Cycles 1 kb up to 0.5 Mb 16 cycles 0.5 Mb up to 1.49 Mb 14 cycles > 1.5 Mb 12 cycles All Exon 10 to 12 cycles As an alternative, you can prepare one PCR master mix as outlined in Table 30. Split this master mix into three small-scale 10-μL PCR reactions and cycle for 10, 12, 14 or 16 cycles. Clean these PCR reactions using the AMPure XP protocol outlined in “Step 2. Purify the sample using Agencourt AMPure XP beads” on page 21 with these modifications: use 30 μL of AMPure XP beads and elute with 20 μL of nuclease-free water. Run these cleaned samples on a DNA 1000 chip on the Bioanalyzer, as described in “Step 3. Assess quality (optional)” on page 22. Use the optimal cycle number to repeat PCR at the 50-μL reaction scale. See Table 33 for approximate number of cycles for a given library size. Results may vary based on library content. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 75 5 Addition of Index Tags by Post-Hybridization Amplification Step 2. Purify the sample using Agencourt AMPure XP beads Step 2. Purify the sample using Agencourt AMPure XP beads 1 Let the AMPure XP beads come to room temperature for at least 30 minutes. 2 Mix the reagent well so that the reagent appears homogeneous and consistent in color. Do not freeze. 3 Add 90 μL of homogeneous AMPure beads to a 1.5-mL LoBind Tube, and add amplified library (~50 μL). Mix well on a vortex mixer and incubate for 5 minutes. 4 Put the tube in the magnetic stand. Wait for the solution to clear (approximately 3 to 5 minutes). 5 Keep the tube in the magnetic stand. Do not touch the beads while you carefully discard the cleared solution from the tubes. 6 Continue to keep the tube in the magnetic stand while you dispense 500 μL of 70% Ethanol in each tube. Use fresh 70% Ethanol for optimal results. 7 Let the tube sit for 1 minute to allow any disturbed beads to settle, and remove the Ethanol. 8 Repeat step 6 and step 7 once. 9 Spin briefly in a centrifuge. Return the tube to the magnetic stand for 30 seconds. Remove residual Ethanol with a P20 pipette. 10 Dry the samples on the 37°C heat block for 5 minutes or until the residual Ethanol is completely evaporated. Do not dry the bead pellet to the point that the bead pellet appears cracked. Elution efficiency is significantly decreased when the bead pellet is excessively dried. 11 Add 30 μL of Nuclease-free Water or 1X Low TE Buffer, mix well on a vortex mixer, and incubate for 2 minutes at room temperature. 12 Put the tube in the magnetic stand and leave for 2 to 3 minutes, until the solution is clear. 13 Remove the supernatant (~30 μL) to a fresh 1.5-mL LoBind Tube. You can discard the beads at this time. Stopping Point 76 If you do not continue to the next step, store the samples at 4°C for up to a week, or at -20°C for longer periods. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Addition of Index Tags by Post-Hybridization Amplification Step 3. Assess quality 5 Step 3. Assess quality Use a Bioanalyzer High Sensitivity DNA Assay or the 2200 TapeStation to assess the quality and size range. 2100 Bioanalyzer High Sensitivity DNA Assay You may need to dilute your sample accordingly. Refer to the Agilent High Sensitivity DNA Kit Guide at http://www.chem.agilent.com/en-US /Search/Library/_layouts/Agilent/PublicationSummary.aspx?whid=59504. 1 Check that the 2100 Bioanalyzer electrodes have been cleaned as instructed in the reagent kit guide. 2 Open the Agilent 2100 Expert Software (version B.02.07 or higher required to run the High Sensitivity Kit), turn on the 2100 Bioanalyzer and check communication. 3 Prepare the chip, samples and ladder as instructed in the reagent kit guide. 4 Load the prepared chip into the 2100 Bioanalyzer and start the run within five minutes after preparation. 5 Within the instrument context, choose the appropriate assay from the drop down list. 6 Start the run. Enter sample names and comments in the Data and Assay context. 7 Verify the results. Determine the concentration of the sample by integration under the peak. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 77 5 Addition of Index Tags by Post-Hybridization Amplification Step 3. Assess quality Figure 14 Analysis of Amplified Capture DNA using the High Sensitivity DNA Kit. The electropherogram shows a peak in the size range of approximately 250 to 350 bp. 2200 TapeStation and High Sensitivity D1000 ScreenTape Use the 2200 TapeStation to analyze the barcoded DNA. Use the High Sensitivity D1000 ScreenTape and High Sensitivity D1000 Reagents. For more information to do this step, see the Agilent 2200 TapeStation User Manual. 1 Prepare the TapeStation samples as instructed in the Agilent 2200 TapeStation User Manual. Use 2 μL of each amplified library DNA sample diluted with 2 μL of High-Sensitivity D1000 sample buffer for the analysis. CAUTION Make sure that you thoroughly mix the combined DNA and High-Sensitivity D1000 sample buffer on a vortex mixer for 5 seconds or more for accurate quantitation. 2 Load the sample plate or tube strips from step 1, the High Sensitivity D1000 ScreenTape, and loading tips into the 2200 TapeStation as instructed in the Agilent 2200 TapeStation User Manual. Start the run. 3 Verify that the electropherogram shows an average DNA fragment size of about 300 bp. A sample electropherogram is shown in Figure 15. Stopping Point 78 If you do not continue to the next step, seal the sample plate and store at 4°C overnight or at –20°C for prolonged storage. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Addition of Index Tags by Post-Hybridization Amplification Step 3. Assess quality Figure 15 5 Analysis of amplified library DNA using the 2200 TapeStation with a High Sensitivity D1000 ScreenTape. The electropherogram shows a peak size range of 250 to 350 bp. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 79 5 Addition of Index Tags by Post-Hybridization Amplification Step 4. Assess the quantity of each index-tagged library by QPCR (optional) Step 4. Assess the quantity of each index-tagged library by QPCR (optional) Refer to the protocol that is included with the QPCR NGS Library Quantification Kit (Illumina GA) for more details to do this step. 1 Use the QPCR NGS Library Quantification Kit (Illumina GA) to determine the concentration of each index-tagged captured library. 2 Prepare a standard curve using the quantification standard included in the kit, according to the instructions provided in the user guide. 3 Dilute each index-tagged captured library such that it falls within the range of the standard curve. Typically this corresponds to approximately a 1:1000 to 1:10,000 dilution of the captured DNA. 4 Prepare the QPCR master mix with Illumina adaptor-specific PCR primers according to instructions provided in the kit. 5 Add an aliquot of the master mix to PCR tubes and add template. 6 On a QPCR system, such as the MX3005P, run the thermal profile outlined in the QPCR NGS Library Quantification kit user guide. Use the SYBR Green instrument setting. 7 Use the standard curve to determine the concentration of each unknown index-tagged library, in nM. The concentration will be used to accurately pool samples for multiplexed sequencing. 80 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Addition of Index Tags by Post-Hybridization Amplification Step 5. Pool samples for Multiplexed Sequencing 5 Step 5. Pool samples for Multiplexed Sequencing 1 Combine the libraries such that each index-tagged sample is present in equimolar amounts in the pool. For each library, use the formula below to determine the amount of index sample to use. Vf Cf Volume of Index = ------------------------------ where # Ci V(f) is the final desired volume of the pool, C(f) is the desired final concentration of all the DNA in the pool, for example, 10 nM for the standard Illumina protocol. # is the number of index, and C(i) is the initial concentration of each index sample. Table 34 shows an example of the amount of 4 index-tagged (of different concentrations) and 1X Low TE Buffer needed for a final volume of 20 μL at 10 nM. Table 34 Example of index volume calculation for a total volume of 20 µL Component V(f) C(i) C(f) # Volume to use (µL) Sample 1 20 µL 20 nM 10 nM 4 2.5 Sample 2 20 µL 10 nM 10 nM 4 5 Sample 3 20 µL 17 nM 10 nM 4 2.9 Sample 4 20 µL 25 nM 10 nM 4 2 1X Low TE Buffer 7.6 2 Adjust the final volume of the pooled library to the desired final concentration. • If the final volume of the combined index-tagged samples is less than the desired final volume, V(f), add 1X Low TE Buffer to bring the volume to the desired level. • If the final volume of the combined index-tagged samples is greater than the final desired volume, V(f), lyophilize and reconstitute to the desired volume. SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 81 5 Addition of Index Tags by Post-Hybridization Amplification Step 6. Prepare sample for cluster amplification 3 If you store the library before sequencing, add Tween 20 to 0.1% v/v and store at -20°C short term. 4 Proceed to template denaturation and flow cell preparation. Refer to the appropriate Illumina protocol. Exact library pool dilution and processing can vary based on the flow cell capacity and analysis pipeline versions being used. Refer to the appropriate Illumina user guide for instructions. This protocol has been validated with 100-base paired-end reads. However, read length can be adjusted to achieve the desired research goals. Step 6. Prepare sample for cluster amplification • Use the appropriate Illumina Paired-End Cluster Generation Kit to do cluster amplification. Refer to the instructions that are included with the Illumina Paired-End Cluster Generation Kit. The optimal seeding concentration for SureSelectXT libraries is 6 to pM, depending on the desired output and data quality. 82 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing Protocol 6 Reference SureSelect Reagent Kit Content 84 Other Reagent Kits Content 86 SureSelectXT Indexes for Illumina 87 Alternative Capture Equipment Combinations 88 This chapter contains reference information. 83 6 Reference SureSelect Reagent Kit Content SureSelect Reagent Kit Content NOTE SureSelect capture libraries and reagents must be used within one year of receipt. Each SureSelect Reagent Kit contains one or more of each of these kits: Table 35 SureSelect Reagent Kit Contents Product Storage Condition 16 96 Reactions Reactions 480 Reactions SureSelect Target Enrichment Kit Box #1 Room Temperature 5190-4393 5190-4394 5190-4395 SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2 -20°C 5190-4455 5190-4456 5190-4457 SureSelect Library Prep Kit, ILM -20°C 5500-0105 5500-0075 The content of each of these kits are described in the next tables. Table 36 SureSelect Target Enrichment Kit Box #1 Kit Component SureSelect Hyb #1 (orange cap, or bottle) SureSelect Hyb #2 (red cap) SureSelect Hyb #4 (black cap, or bottle) SureSelect Binding Buffer SureSelect Wash 1 SureSelect Wash 2 SureSelect Elution Buffer* SureSelect Neutralization Buffer* * These reagents are not used in this protocol. 84 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Reference SureSelect Reagent Kit Content Table 37 6 SureSelect Target Enrichment Kit ILM Indexing Hyb Module Box #2 Kit Component SureSelect Hyb #3 (yellow cap) SureSelect Indexing Block #1 (green cap) SureSelect Block #2 (blue cap) SureSelect Indexing Block #3 (brown cap) SureSelect RNase Block (purple cap) SureSelect ILM Indexing Pre Capture PCR Reverse Primer (clear cap) SureSelect ILM Indexing Post Capture Forward PCR Primer (orange cap) Table 38 SureSelect Library Prep Kit, ILM Kit Component 10× End Repair Buffer (clear cap) T4 Polynucleotide Kinase (orange cap) 10× Klenow Polymerase Buffer (blue cap) T4 DNA Ligase (red cap) Exo(-) Klenow (red cap) T4 DNA Polymerase (purple cap) Klenow DNA Polymerase (yellow cap) dATP (green cap) dNTP Mix (green cap) SureSelect Adaptor Oligo Mix (brown cap) SureSelect Primer (brown cap) PCR Primer Index 1 through Index 16 (clear caps) 5× T4 DNA Ligase Buffer SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 85 6 Reference Other Reagent Kits Content Other Reagent Kits Content These reagents are from kits other than the SureSelect Reagent kit. Make sure you use only the reagents listed here. Table 39 Herculase II Fusion DNA Polymerase (Agilent) Component DMSO (green cap) 5× Herculase II Rxn Buffer (clear cap) 100 mM dNTP Mix (green cap) Herculase II Fusion DNA Polymerase (red cap) Table 40 D1000 Reagents (Agilent p/n 5067-5583) Components D1000 ladder D1000 sample buffer Table 41 High Sensitivity D1000 Reagents (Agilent p/n 5067-5585) Components High-Sensitivity D1000 ladder High-Sensitivity D1000 sample buffer 86 SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing Reference SureSelectXT Indexes for Illumina 6 SureSelectXT Indexes for Illumina The nucleotide sequence of each of the SureSelectXT index is listed in Table 42. Table 42 SureSelectXT Indexes 1-16 Index Number Sequence 1 ATCACG 2 CGATGT 3 TTAGGC 4 TGACCA 5 ACAGTG 6 GCCAAT 7 CAGATC 8 ACTTGA 9 GATCAG 10 TAGCTT 11 GGCTAC 12 CTTGTA 13 AAACAT 14 CAAAAG 15 GAAACC 16 AAAGCA SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing 87 6 Reference Alternative Capture Equipment Combinations Alternative Capture Equipment Combinations Table 43 lists combinations of thermal cycler, lid temperature, plates or strips, and sealing method (strip caps or sealing tape) other than those used in this protocol that have shown minimal evaporation. Refer to this list for additional of equipment combination options for hybridization. Note that minimal evaporation is needed to ensure good capture results. Table 43 Tested options that show minimal evaporation PCR Machine Plate/Strips Cover Comments Agilent Mx3005P QPCR Mx3000P Strip Tubes (401428) MX3000P Optical Strip Caps (401425) Heated Lid Agilent Mx3005P QPCR MicroAmp Optical 96-well reaction plate (N801-0560) MicroAmp Clear Adhesive Film (4306311) Heated Lid; ABI compression pad (4312639) Use two layers of film. ABI GeneAmp 9700 MicroAmp Optical 96-well Reaction Plate (N801-0560) MicroAmp Caps (8caps/strip) (N801-0535) Heated Lid ABI Veriti (4375786) MicroAmp Clear Adhesive Film (4306311) Heated Lid; ABI compression pad (4312639) MicroAmp Optical 96-well Reaction Plate (N801-0560) Use two layers of film. 88 Eppendorf Mastercycler Eppendorf 8-Tube PCR Tubes Attached lids Lid heating set to 75°C BioRad (MJ Research) PTC-200 Agilent strip tubes 410022 (Mx4000) Agilent Optical cap 410024 (Mx4000) Heated Lid BioRad (MJ Research) PTC-200 Agilent strip tubes 410022 (Mx4000) Agilent Optical cap 401425 (Mx3000/3005) Heated Lid BioRad (MJ Research) PTC-200 Agilent 96-well Plate 410088 (Mx3000/3005) Agilent Optical cap 401425 (Mx3000/3005) Heated Lid SureSelectXT Target Enrichment System Kit for Illumina Multiplexed Sequencing www.agilent.com In This Book This guide contains information to run the SureSelectXT Target Enrichment System for Illumina Paired-End Sequencing protocol with the Illumina HiSeq and MiSeq Multiplexed Sequencing Platforms. Agilent Technologies, Inc. 2014 Version 1.7, July 2014 *G7530-90000* G7530-90000 Revision A9 Agilent Technologies
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Download PDF
advertisement