AC-3000 - Rice Lake Weighing Systems
AC-3000
Retail Scale
Operating Manual
48743
1
This manual is based on standard
specifications. Therefore, application
of this manual may depend on the
country standards or customer
specifications.
You can help to improve this manual
by calling attention to errors and
by recommending improvements.
Please convey your comments to the
nearest Ishida Company regional
representative.
Thank you!
Copyright  1997 by Ishida Co., Ltd. All Rights Reserved.
No part of this manual may be reproduced in any form, by mimeograph
or any other means, without written permission of the publisher.
CAUTIONS FOR USE
§ Always operate the scale on
a level surface.
§ Do not disassemble the scale.
§ Do not expose the scale to direct
sunlight for long periods.
§ Do not allow any liquids to come
into contact with the scale or
terminal.
§ Do not drop or apply a strong
shock to the scale.
§ When cleaning the scale, only use
a soft dry cloth or a cloth wetted
with a neutral cleanser.
Never use thinner or other volatile
liquids.
A
C
Always operate the scale with
the same rated AC power supply
shown on the specification plate.
SAFETY CONSIDERATIONS
To ensure safe operation, the general safety considerations below must be
followed.
Grounding
This instrument is a Class 1 device which requires protective grounding for safe
operation.
To avoid potential shock hazards, a protective grounding conductor for the
instrument must be securely connected to the main grounding provision by
qualified service personnel.
Do not remove covers or enclosures
To avoid personal injury and shock, do not open or remove any covers or
enclosures of the instrument unless specified in the manual.
Do not perform unspecified maintenance
For your personal safety, do not perform any maintenance procedures which
are not specified in the manual.
Disconnect power supply before servicing
To ensure your personal safety, disconnect the power supply before servicing.
CONTENTS
Chapter 1: Overview
1.1 Appearance ......................................................................................................... 2
1.2 Operator Display .................................................................................................. 2
1.3 Operation Keys ..................................................................................................... 3
1.4 Loading Label/Receipt Roll ................................................................................. 6
1.5 Pre-operation Inspection ..................................................................................... 8
1.6 Power On ............................................................................................................... 9
Chapter 2: Basic Operation for Label Application
2.1 Label Operation Flow ......................................................................................... 12
2.2 Counter Sale of Weighed Item .......................................................................... 13
2.3 Counter Sale of Fixed-price Item ..................................................................... 14
2.4 Prepack for Weighed Item ................................................................................ 15
2.5 Prepack for Fixed-price Item ............................................................................ 16
2.6 Label Batch Print ................................................................................................. 17
2.7 Pack Count Sub-total ......................................................................................... 18
Chapter 3: Basic Operation for Receipt Application
3.1 Receipt Operation Flow ..................................................................................... 20
3.2 Weighted Item Sale ............................................................................................ 21
3.3 Fixed-price Item Sale......................................................................................... 23
3.4 Payment Media .................................................................................................. 25
3.5 Subtotal Discount................................................................................................ 26
3.6 Returned Item ..................................................................................................... 27
Chapter 4: On-demand Operation
4.1 Mark Down Functions......................................................................................... 30
4.2 Unit Price Override ............................................................................................. 31
4.3 Voiding the Last Transaction .............................................................................. 31
4.4 Changing from Weighed Item to Fixed-price Item ......................................... 31
4.5 Fixed Weight Override ....................................................................................... 31
4.6 Date Override ..................................................................................................... 32
4.7 Save ..................................................................................................................... 32
4.8 Logo Print ............................................................................................................. 32
4.9 Store Name Print ................................................................................................. 33
4.10 Extra Text Print ..................................................................................................... 33
4.11 POP Text Print ...................................................................................................... 33
4.12 Coupon Text Print ............................................................................................... 34
Chapter 5:
Subtraction
5.1 Subtraction .......................................................................................................... 36
Chapter 6:
Troubleshooting
6.1 Error Messages .................................................................................................... 40
6.2 How to Release Error Conditions ....................................................................... 41
6.3 How to Replace Fuse ......................................................................................... 41
6.4 Other Problems ................................................................................................... 41
CHAPTER
1
OVERVIEW
Contents
1.1
Appearance ..................................... 2
1.2
Operator Display .............................. 2
1.3
Operation Keys ................................. 3
1.3.1
1.3.2
1.3.3
1.3.4
Operation Key Sheet ....................................... 3
Basic Function Keys .......................................... 4
Additional Function Keys ................................. 5
Preset Key Examples ........................................ 5
1.4
Loading Label/Receipt Roll ............. 6
1.4.1 AC-3000 ............................................................. 6
1.4.2 AC-3000E ........................................................... 7
1.5
Pre-operation Inspection ................. 8
1.6
Power On ........................................... 9
1.1
Appearance
Customer Display
Operator Display
ZERO
NET
SAVE
AUTO
Weigh Platter
Side Cover
Printer
Power Switch
Fuse
Key Sheet
Level Adjustment
Note: The above illustration is of the AC-3000.
1.2
Operator Display
WEIGHT
lb
ZERO
NET
$
UNIT PRICE
SAVE
TOTAL PRICE
$
AUTO
PLU
Capacity 30 × 0.01 lb
AC
AC-3000 Operator Display
E
AC
WEIGHT
lb
ZERO
NET
UNIT PRICE
SAVE
Capacity 30 × 0.01 lb
$
TOTAL PRICE
$
AUTO
PLU
AC-3000E Operator Display
Indicators
ZERO: Lights when weight value is true zero or temporary zero.
NET : Lights when a tare is used.
SAVE : Lights when the SAVE mode is used.
AUTO: Lights when the AUTOMATIC PRINT (prepack) mode is
used.
page 8
AC-3000/3000E • User’s Manual (Operator)• Rev 0
1.3
Operation Keys
1.3.1 Operation Key Sheet
PACK
COUNT
ZERO
HELP
VOID
RESET
PGM
MODE
LABEL LOWER
BATCH PRESET
DATE
X
MULTIPLY
PRE
PACK
7
8
9
4
5
6
1
2
3
0
CLR
TARE
PLU
RE
TURN
ZERO
HELP
VOID
RESET
PGM
MODE
CHANGE
LOWER
PRESET
PAPER
FEED
PRINT
Key Sheet for Label Application
DATE
X
MULTIPLY
PRE
PACK
PAPER
FEED
7
8
9
SUB
TOTAL
4
5
6
AMT
TOTAL
1
2
3
0
CLR
TARE
PLU
Key Sheet for Receipt Application
Preset Keys
Additional Function Keys
Four of the following options can
be preset by the dealer in
accordance with the customer‘s
request.
Program
Key Sheet
Operation
Key Sheet
Insert the Operation Key Sheet
over the Program Key Sheet.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
•
•
•
•
•
•
•
•
•
•
•
•
•
DATE/TIME display
STORE NAME number
LOGO number
EXTRA TEXT number
POP TEXT number
COUPON TEXT number
FIXED PRICE
DISCOUNT
AMOUNT DISCOUNT
PERCENTAGE DISCOUNT
SAVE
FIXED WEIGHT
PRINT
page 9
1.3.2 Basic Function Keys
NUMERIC ENTRY
Keys 0 through 9 are used to enter
numeric data.
TARE
TARE
Used to subtract the tare weight from the
total weight on the weigh platter.
DATE
TEMPORARY DATE
Used to temporarily change the current
date.
VOID
VOID
Used to cancel the previous item registration.
ZERO
ZERO ADJUSTMENT
Used to return the scale to zero when
nothing is on the weigh platter.
HELP
HELP (AC-3000 only)
Used to display an explanation (up to 32
letters) of each function.
PACK
COUNT
PACK COUNT SUB-TOTAL
(label application only)
Used to issue a label that shows the
number of labels (packs), total weight and
amount which have been transacted
since this key was last pressed.
RESET
RESET
Used to forcibly exit a particular mode and
return to the initial status of the operation
mode.
PAPER
FEED
PAPER FEED
Used to advance labels/receipts to the
correct printing position.
RE
TURN
PLU
PLU SELECT
Used to access PLU data.
Also used to display the tare weight.
CHANGE
CHANGE (receipt application only)
Used when exchanging money. Also used
to open the cash drawer.
PRE
PACK
PREPACK
Used to switch between auto printing
mode and manual printing mode.
SUB
TOTAL
SUBTOTAL (receipt application only)
U s e d t o s u b t o t a l t h e c u s t o m e r ’s
purchases.
PRINT
PRINT (label application only)
Used to print labels/receipts.
~
0
~
9
CLR
CLEAR
Used to cancel incorrectly entered
numeric data.
Also used to stop printing labels.
Also used to return to the operation mode.
LABEL
BATCH
LABEL BATCH (label application only)
Used to issue batches of labels.
LOWER
PRESET
LOWER PRESET
Used to access the second level of data
programmed to the preset keys.
X
MULTIPLY
Used to multiply the entered quantity of
fixed-price items.
MULTIPLY
PGM
MODE
page 10
AMT
TOTAL
RETURN (receipt application only)
Used to register the returned item.
AMOUNT TOTAL
(receipt application only)
Used to finalize the cash payment
transaction, and also use to calculate the
change due.
PROGRAM MODE
Used to enter the subtraction mode after
a 4-digit password has been entered.
Also used to exit the subtraction mode.
AC-3000/3000E • User’s Manual (Operator)• Rev 0
1.3.3 Additional Function Keys
DATE
TIME
DATE/TIME
Used to display the current date and time
for a few seconds.
STORE
NAME
STORE NAME
Used to change the store name corresponding to the entered number.
LOGO
LOGO
Used to access a logo message corresponding to the entered number after the
PLU has been accessed.
EXTRA
TEXT
EXTRA TEXT
Used to access an extra message corresponding to the entered number after the
PLU has been accessed.
POP
TEXT
POP TEXT
Used to access the POP text corresponding to the entered number after the
PLU has been accessed.
COUPON
TEXT
COUPON TEXT
Used to access a coupon message
corresponding to the entered number
after the PLU has been accessed.
FIXED
WEIGHT
FIXED WEIGHT
Used to temporarily change a fixed weight
of the fixed price item.
FIXED
PRICE
DISCOUNT
FIXED PRICE
Used to temporarily change from weight
item sales to fixed-price item sales.
Also used to enter a new fixed price.
DISCOUNT
Used to enter a special selling price.
–$
AMOUNT DISCOUNT
Used to subtract the entered amount from
the selling price.
–%
PERCENTAGE DISCOUNT
Used to subtract the entered percentage
from the selling price.
SAVE
SAVE
Used to save PLU data until the SAVE
key is pressed again.
PRINT
PRINT (receipt application only)
Used to print labels.
Also used to start batch printing.
1.3.4 Preset Key Examples
CHECK
CARD
CHECK (receipt application only)
Used to finalize check payment
transactions.
TARE
#1
CARD (receipt application only)
Used to finalize credit card payment
transactions.
–%
OPE
#1
OPERATOR PRESET
Used as a PRINT key by the designated
operator.
PLU10
PLU90
PLU PRESET
Used to access PLU data (from among
two levels).
AC-3000/3000E • User’s Manual (Operator) • Rev 0
–$
TARE PRESET
Used to access preset tare weight.
PERCENT DISCOUNT
Used to access preset discount
percentage.
AMOUNT DISCOUNT
Used to access preset discount amount.
page 11
1.4
Loading Label/Receipt Roll
1.4.1 AC-3000
1.
Pull and remove the cassette from the main body.
CAUTION
2.
When removing or replacing the cassette,
securely grip the handle so as not to drop
the cassette.
Load the new roll into the cassette and secure it with
the roll clasp.
Note: Before installing the label roll, remove labels
from the first 30 cm (12 inches) of backing
paper.
30
cm
A
3.
Thread the paper through positions shown in the
diagram.
B
4.
C
Wind the end of the backing paper around the winding
sleeve, and secure it with the U-pin as shown in the
diagram.
D
5.
6.
Replace the cassette into the main body by pushing it
straight in until it is fully inserted.
Press the PAPER FEED key to advance the label/
receipt to the correct printing position.
page 12
E
PAPER
FEED
AC-3000/3000E • User’s Manual (Operator)• Rev 0
1.4.2 AC-3000E
1.
Make sure that the power is off.
2.
Open the side cover.
3.
Pull the release lever to raise the printer head.
4.
Load the new roll onto the holding shaft.
5.
30
cm
Note: Before installing the label roll, remove labels
from the first 30 cm (12 inches) of backing
paper.
Thread the paper through positions as shown in the diagram.
Check that the backing paper is:
• threaded properly under the guide shaft.
• threaded properly through the label sensor.
• threaded properly over the peeling bar, making sure
it passes through the groove.
Release Lever
Label Holding Shaft
Printer Head
Release Lever
Label Holding Shaft
Printer Head
Label Guide
Label Guide
Printer
Unit
Printer
Unit
U-pin
Peeling Bar
Peeling Bar
Label Sensor
Winding Sleeve
Label Sensor
Guide Shaft
Guide Shaft
6.
When the label needs to be wound up, wind the end
of the backing paper around the winding sleeve and
secure it with the U-pin as shown in the diagram.
7.
Push the printer head down until it locks securely.
8.
Close the side cover.
9.
Turn on the power and press the PAPER FEED key
to advance the label/receipt to the correct printing
position.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
a
PAPER
FEED
page 13
1.5
Pre-operation Inspection
In order to maintain optimum scale performance, perform the following inspection before starting daily operations.
Always turn off the power switch when performing this inspection.
CAUTION
1.
Make sure that the power is off.
2.
Check that the scale and the level device aperture are clean and free of foreign matter, label adhesive,
etc. to make the scale level. If not, wipe any soiled areas with a dry cloth.
3.
In order to maintain good printing quality, clean the thermal head at least once a week with a cotton
swab dipped in cleaning fluid.
Thermal Head
Do not use metal tools to clean the thermal head as they may
damage the head surface.
CAUTION
4.
Adjust the scale to level by using the height adjustment feet.
Level Indicator
Correct
Incorrect
Height Adjustment
5.
page 14
Make sure the label/receipt amount is sufficient.
AC-3000/3000E • User’s Manual (Operator)• Rev 0
1.6
Power On
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Make sure that the power cord is pluged
into the AC outlet.
C
A
2 Turn on the power switch.
3 Make sure that nothing is on the weigh
platter.
4 Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key.
KEY IN ITEM No.
ZERO
Initial display
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 15
CHAPTER
2
BASIC OPERATION
FOR LABEL
APPLICATION
Contents
2.1
Label Operation Flow .................... 12
2.1.1 Start-up Operations ....................................... 12
2.1.2 Operation Flow ............................................... 12
2.2
Counter Sale of Weighed Item ..... 13
2.3
Counter Sale of Fixed-price Item .. 14
2.4
Prepack for Weighed Item ............ 15
2.5
Prepack for Fixed-price Item ......... 16
2.6
Label Batch Print............................. 17
2.7
Pack Count Sub-total ..................... 18
2.1
Label Operation Flow
2.1.1
Start-up Operations
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
(1) Label issuing mode
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• If automatic printing is desired, press the
PREPACK key to turn on the AUTO indicator, if
it is not lit.
(2) Receipt issuing mode
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
2.1.2
PRE
PACK
KEY IN ITEM No.
ZERO
AUTO
KEY IN ITEM No.
ZERO
Operation Flow
Counter Sale
Weighed Item
(Section 2.2)
Fixed Price Item
(Section 2.3)
On-demand Operations
(Chapter 4)
Label Issue
AC-3000/3000E • User’s Manual (Operator) • Rev 0
Prepack
Weighed Item
(Section 2.4)
Fixed Price Item
(Section 2.5)
On-demand Operations
(Chapter 4)
Label Issue
page 17
2.2
Counter Sale of Weighed Item
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Confirm that the initial display appears
on the screen.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
2 Enter the PLU.
§ Entering PLU number
• Enter the PLU number and press the PLU key.
✱TOTAL
MODE
KEY
IN ITEM
No.
PRESS [ ] KEY
ZERO
3
5
0
✱TOTAL
FILET MIGNON
MODE
➔
PLU
PRESS [ ] KEY
Example: PLU no. = 350
--------------------------------------------------------------Example: When accessing PLU10
§ Pressing PLU (preset) key
PLU10
• Press the preset key in which the PLU number
PLU90
is set.
--------------------------------------------------------------Example: When accessing PLU90
Note: When accessing the lower preset PLU
LOWER
number, press the LOWER PRESET key
➔ PLU10
PRESET
PLU90
prior to pressing the preset key.
3 Subtract the tare.
§ Weighing tare
• Place the tare on the weigh platter.
• Press the TARE key.
➔
TARE
NET
---------------------------------------------------------------§ Entering tare weight
• Enter the tare weight and press the TARE key.
8
➔
TARE
Example: Tare weight = 0.08 lb.
§ Pressing tare look-up key
• Press the Tare Look-Up (preset) key.
---------------------------------------------------------------TARE
#1
Example: Tare look up #1 = 0.12 lb.
4 Weigh the item.
• Place the item on the weigh platter.
Example: Net weight = 8.60 lb.
Unit price = $2.20/lb.
✱TOTAL
MODE
FILET MIGNON
PRESS [ ] KEY
5 Issue the label.
§ When the operator system is not used,
• Press the PRINT key.
§ When the operator system is used,
• Press the OPERATOR (preset) key.
page 18
PRINT
--------------------------------------------------------------Susan
AC-3000/3000E • User’s Manual (Operator)• Rev 0
2.3
Counter Sale of Fixed-price Item
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Confirm that the initial display appears
on the screen.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
2 Enter the PLU.
ZERO
5
4
§ Entering PLU number
• Enter the PLU number and press the PLU key.
Example:
KEY IN ITEM No.
➔
0
✱TOTAL MODE
SAUSAGE
PLU
PRESS [ ] KEY
PLU no. = 450
Fixed price = $2.20
§ Pressing PLU (preset) key
• Press the preset key in which the PLU number
is set.
Note: When accessing the lower preset PLU
number, press the LOWER PRESET key
prior to pressing the preset key.
---------------------------------------------------------------Example: When accessing PLU15
PLU15
PLU95
---------------------------------------------------------------Example: When accessing PLU95
3 Multiply the quantity, if any.
• When selling more than one of the same item,
enter the quantity and press the MULTIPLY
key.
➔
LOWER
PRESET
X
MULIPLY
➔
3
PLU15
PLU95
✱TOTAL
SAUSAGEMODE
PRESS [ ] KEY
• Otherwise, go to the next step.
4 Issue the label.
§ Multiple labels
• Enter the number of labels, and press the
PRINT key.
§ One label
• Press the PRINT key when the operator
system is not used.
Example: Ten labels
1
0
➔
PRINT
---------------------------------------------------------------Example: One label
PRINT
OR
Susan
OR
• Press the OPERATOR (preset) key when the
operator system is used.
Note: Press the CLEAR key once to temporarily
stop printing.
To continue printing, press the PRINT key
again.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 19
2.4
Prepack for Weighed Item
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Enter the prepack mode.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Press the PREPACK key to turn on the AUTO
indicator, if it is not lit.
PRE
PACK
KEY IN ITEM No.
2 Enter the PLU.
§ Entering PLU number
• Enter the PLU number and press the PLU key.
AUTO
ZERO
3
5
0
➔
PLU
FILET MIGNON
Example: PLU no. = 350
---------------------------------------------------------------§ Pressing PLU (preset) key
Example: When accessing PLU10
• Press the preset key in which the PLU number
PLU10
is set.
PLU90
Note: When accessing the lower preset PLU ---------------------------------------------------------------Example: When accessing PLU90
number, press the LOWER PRESET key
LOWER
prior to pressing the preset key.
➔ PLU10
PRESET
3 Subtract the tare.
PLU90
➔
TARE
§ Weighing tare
• Place the tare on the weigh platter.
• Press the TARE key.
NET
AUTO
---------------------------------------------------------------§ Entering tare weight
8 ➔ TARE
• Enter the tare weight and press the TARE key.
Example: Tare weight = 0.08 lb.
§ Pressing tare look-up key
• Press the Tare Look-Up (preset) key.
---------------------------------------------------------------TARE
#1
Example: Tare look up #1 = 0.12 lb.
4 4 Weigh the item.
• Place the item on the weigh platter.
Example: Net weight = 8.60 lb.
Unit price = $2.20/lb.
✱TOTAL
FILET MIGNON
MODE
PRESS [ ] KEY
• The label is automatically printed.
• Repeat this step until all the items of the same
PLU are weighed.
5 Exit the prepack mode.
• Press the PREPACK key.
• The AUTO indicator will turn off.
PRE
PACK
KEY IN ITEM No.
ZERO
page 20
AC-3000/3000E • User’s Manual (Operator)• Rev 0
2.5
Prepack for Fixed-price Item
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Enter the prepack mode.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Press the PREPACK key to turn on the AUTO
indicator, if it is not lit.
PRE
PACK
KEY IN ITEM No.
AUTO
ZERO
2 Enter the PLU.
§ Entering PLU number
• Enter the PLU number and press the PLU
key.
Example:
PLU no. = 450
Fixed price = $2.20
§ Pressing PLU (preset) key
• Press the preset key in which the PLU number
is set.
5
4
➔
0
PLU
SAUSAGE
---------------------------------------------------------------Example: When accessing PLU15
PLU15
PLU95
---------------------------------------------------------------Example: When accessing PLU95
Note: When accessing the lower preset PLU
number, press the LOWER PRESET key
prior to pressing the preset key.
➔
LOWER
PRESET
PLU15
PLU95
3 Print labels.
§ Continuous issue
PRINT
• Press the PRINT key to continuously issue
labels.
•••••
• Press the CLEAR key to stop printing.
§ Specified number of labels
CLR
---------------------------------------------------------------Example: Ten labels
• Enter the number of labels, and press the
PRINT key.
1
Note: Press the CLEAR key once to temporarily
stop printing.
To continue printing, press the PRINT key
again.
➔
PRINT
•••••
4 Exit the prepack mode.
• Press the PREPACK key.
• The AUTO indicator will turn off.
0
PRE
PACK
KEY IN ITEM No.
ZERO
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 21
2.6
Label Batch Print
This function presets the number of fixed-price labels (max. 20 PLUs) to be printed. This function is only available
for fixed-price items.
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Enter the label batch print mode.
• Press the LABEL BATCH key to enter the
label batch print mode.
LABEL
BATCH
✱TOTAL
✱BATCH MODE
MODE
PRESS [ ] KEY
2 Enter the PLU.
4
5
➔
0
PLU
§ Entering PLU number
• Enter the PLU number and press the PLU key.
✱TOTAL
✱BATCH MODE
MODE SAUSAGE PRESS [ ] KEY
Example: PLU no. = 450
§ Pressing PLU (preset) key
• Press the preset key in which the PLU number
is set.
Note: When accessing the lower preset PLU
number, press the LOWER PRESET key
prior to pressing the preset key.
3 Enter the desired number of labels.
• Enter the number of labels to be issued.
(Max. 999)
• Press the LABEL BATCH key.
---------------------------------------------------------------Example: When accessing PLU15
PLU15
PLU95
---------------------------------------------------------------Example: When accessing PLU95
➔
LOWER
PRESET
PLU15
PLU95
Example: Twenty labels
2
0
➔
LABEL
BATCH
✱TOTAL MODE SAUSAGE PRESS [ ] KEY
✱BATCH
4 Enter any other PLUs, if necessary.
• Repeat steps 2 and 3 when labels for any
other PLUs are needed. A maximum of 20
PLUs can be entered.
5 Print labels.
• Press the PRINT key.
Note: Press the CLEAR key to temporarily stop
printing.
To continue printing, press the PRINT
key again.
To cancel batch, press CLEAR key
again.
page 22
PRINT
•••••
AC-3000/3000E • User’s Manual (Operator)• Rev 0
2.7
Pack Count Sub-total
This function is used to print the pre-packing information label, including the total quantity, total weight and total
amount which have been issued since the last time the PACK COUNT key was pressed.
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Enter the pack count sub-total mode.
PACK
COUNT
• Press the PACK COUNT key.
✱TOTAL TO
MODE
PRESS [ ] KEY
[PRINT]
PRODUCE SUBTOTAL
2 Print the pack count sub-total.
PRINT
• Press the PRINT key.
• The scale returns to the initial display after
issuing pack count sub-total label.
KEY IN ITEM No.
ZERO
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 23
CHAPTER
3
BASIC OPERATION
FOR RECEIPT
APPLICATION
Contents
3.1
Receipt Operation Flow ................ 20
3.1.1 Start-up Operations ....................................... 20
3.1.2 Operation Flow ............................................... 20
3.2
Weighed Item Sale ......................... 21
3.3
Fixed-price Item Sale ...................... 23
3.4
Payment Method ........................... 25
3.4.1
3.4.2
3.4.3
3.4.4
Cash Payment ................................................ 25
Check Payment ............................................. 25
Card Payment ................................................ 25
Mixed Payments ............................................. 25
3.5
Subtotal Discount ........................... 26
3.5.1 Subtotal Amount Discount ............................ 26
3.5.2 Subtotal Percent Discount ............................ 26
3.5.3 Subtotal Special Price .................................... 26
3.6
Returned Item ................................. 27
3.1
Receipt Operation Flow
3.1.1
Start-up Operations
(1) Label issuing mode
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
PRE
PACK
KEY IN ITEM No.
• Press the PREPACK key to turn on the AUTO
indicator, if it is not lit.
ZERO
(2) Receipt issuing mode
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
KEY IN ITEM No.
ZERO
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
3.1.2
AUTO
Operation Flow
■ On-Demand Operations
(Chapter 4)
• Unit price override
• Item amount discount
• Item percent discount
• Item special price
• Fixed-price sale
Weighed Item Sale
(Section 3.2)
Fixed-price Item Sale
(Section 3.3)
■ On-Demand Operations
(Chapter 4)
• Quantity multiplication
• Fixed-price change
• Item amount discount
• Item percent discount
• Item special price
• Subtotal amount discount (Section 3.5.1)
• Subtotal percent discount (Section 3.5.2)
• Subtotal special price (Section 3.5.3)
• Returned item (Section 3.6)
• Cash payment (Section 3.4.1)
• Check payment (Section 3.4.2)
• Card payment (Section 3.4.3)
• Mixed payments (Section 3.4.4)
Finalizing
Transaction
Issuing Receipts
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 25
3.2
Weighed Item Sale
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Confirm that the initial display appears
on the screen.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
✱TOTAL
KEY IN ITEM
MODE
No.
PRESS [ ] KEY
ZERO
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
2 Enter the PLU.
§ Entering PLU number
• Enter the PLU number and press the PLU key.
3
5
0
➔
✱TOTAL
MODE
FILET MIGNON
PLU
PRESS [ ] KEY
Example: PLU no. = 3 5 0
---------------------------------------------------------------§ Pressing PLU (preset) key
Example: When accessing PLU10
• Press the preset key in which the PLU number
PLU10
is set.
PLU90
---------------------------------------------------------------Example: When accessing PLU90
Note: When accessing the lower preset PLU
LOWER
number, press the LOWER PRESET key
➔ PLU10
PRESET
PLU90
prior to pressing the preset key.
3 Subtract the tare.
➔
§ Weighing tare
• Place the tare on the weigh platter.
• Press the TARE key.
§ Entering tare weight
• Enter the tare weight and press the TARE key.
TARE
NET
---------------------------------------------------------------8
➔
TARE
Example: Tare weight = 0.08 lb.
§ Pressing tare look-up key
• Press the Tare Look-Up (preset) key.
---------------------------------------------------------------TARE
#1
Example: Tare look up #1 = 0.12 lb.
4 Weigh the item.
• Place the item on the weigh platter.
Example: Net weight = 8.60 lb.
Unit price = $2.20/lb.
✱TOTAL
FILET
MIGNON
MODE
Susan
• Press the OPERATOR (preset) key in which the
operator’s number is set.
✱ADD
page 26
PRESS [ ] KEY
OPE:01
TOTAL 18.92
AC-3000/3000E • User’s Manual (Operator)• Rev 0
5 Repeat the item sale, if any.
1
• Repeat steps 2, 3 and 4 for any other items.
5
➔
0
PLU
Example: PLU no. = 1 5 0
Net weight = 2.50 lb.
Unit price = $1.50/lb.
✱TOTAL
MODE
LAMB CHOPS
PRESS [ ] KEY
Susan
✱ADD
6 Issue the receipt.
• Enter the amount tendered by the customer
and press the AMOUNT TOTAL key. Then the
change due will be calculated and the receipt
will be issued.
OPE:01
Example: The customer pays $30.00.
3
0
✱AMOUNT
AC-3000/3000E • User’s Manual (Operator) • Rev 0
TOTAL 22.67
0
0
PCS02
➔
AMT
TOTAL
CHANGE 7.33
page 27
3.3
Fixed-price Item Sale
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Confirm that the initial display appears
on the screen.
• Check that nothing is on the weigh platter.
• Check that the ZERO indicator is lit.
Note: If the ZERO indicator is not lit, press the
ZERO key to turn on the indicator.
• Check that the AUTO indicator is not lit.
Note: If the AUTO indicator is lit, press the
PREPACK key to turn off the indicator.
KEY IN ITEM No.
ZERO
2 Enter the PLU.
4
5
0
➔
PLU
§ Entering PLU number
• Enter the PLU number and press the PLU key.
Example:
✱TOTAL
SAUSAGEMODE
PRESS [ ] KEY
PLU no. = 4 5 0
Fixed price = $2.20
• Press the OPERATOR (preset) key to register
a single item.
Note: The OPERATOR key depression is not
necessary when using the multiply
function (selling more than one of the
same item).
§ Pressing PLU (preset) key
• Press the preset key in which the PLU number
is set.
• Press the OPERATOR (preset) key to register
a single item.
Note 1. The OPERATOR key depression is
not necessary when using the
multiply function (selling more than
one of the same item).
2. When accessing the lower preset
PLU number, press the LOWER
PRESET key prior to pressing the
preset key.
Susan
✱TOTAL MODE OPE:01 PRESS
] KEY
✱ADD
TOTAL[ 2.20
---------------------------------------------------------------Example: When accessing PLU15
PLU15
PLU95
➔
Susan
---------------------------------------------------------------Example: When accessing PLU95
LOWER
PRESET
➔
PLU15
PLU95
➔
Susan
3 Multiply the quantity, if any.
• When selling more than one of the same item,
enter the quantity and press the MULTIPLY
key and then press the OPERATOR (preset)
key to register the multiple items.
3
➔
✱TOTAL MODE
SAUSAGE
X
MULIPLY
PRESS [ ] KEY
• Otherwise, go to the next step.
Susan
page 28
AC-3000/3000E • User’s Manual (Operator)• Rev 0
4 Repeat the item sale, if any.
4
➔
0
8
PLU
• Repeat steps 2 and 3 for any other items.
✱TOTAL
LETTUCEMODE
Example:
PRESS [ ] KEY
PLU no. =
480
Fixed price = $0.98
5
Susan
✱TOTAL
✱ADD MODE OPE:01
5 Issue the receipt.
• Enter the amount tendered by the customer
and press the AMOUNT TOTAL key. Then the
change due will be calculated and the receipt
will be issued.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
PRESS
] KEY
TOTAL[ 7.58
Example: The customer pays $10.00.
1
0
✱AMOUNT
0
0
PCS02
➔
AMT
TOTAL
CHNAGE 2.42
page 29
3.4
3.4.1
Payment Method
Cash Payment
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Finalize the transaction.
✱TOTAL MODE OPE:01 PRESS
✱ADD
TOTAL[ 7.58
] KEY
• Enter the amount tendered by the customer if
any.
• Press the AMOUNT TOTAL key, and the receipt
will be issued.
Note: At this time the change due will be
calculated if the tendered amount has been
entered.
3.4.2
Example: The customer pays $10.00.
1
0
0
➔
0
AMT
TOTAL
✱AMOUNT
PCS02
CHANGE 2.42
✱ADD
OPE:01
TOTAL 7.58
Check Payment
1 Finalize the transaction.
• Press the CHECK key, and the receipt will be
issued.
CHECK
3.4.3
Card Payment
1 Finalize the transaction.
✱ADD
OPE:01
TOTAL 7.58
• Press the CARD key, and the receipt will be
issued.
CARD
3.4.4
Mixed Payments
1 Enter first payment.
✱ADD
OPE:01
TOTAL 70.50
• Enter the first payment amount tendered by
the customer.
• Press the key corresponding to the payment
media.
2 Enter additional payments.
• Repeat the steps above until the complete
payment has been made.
\
Example: The customer pays $10.50 in cash.
1
0
5
✱AMOUNT
0
➔
AMT
TOTAL
PCS02 BALANCE 60.00
Example: The customer pays the balance by check.
CHECK
page 30
AC-3000/3000E • User’s Manual (Operator)• Rev 0
3.5
3.5.1
Subtotal Discount
Subtotal Amount Discount
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Obtain the subtotal amount.
• Press the SUBTOTAL and OPERATOR
(preset) keys.
2 Perform discount operation.
• Enter the discount amount and press the
AMOUNT DISCOUNT key.
➔
SUB
TOTAL
✱SUBTOTAL
Susan
OPE:01
Example: Discount amount = $2.00
2
0
➔
0
PRE
OPE:01
PACK
✱DISCOUNT
✱TOTAL
MODE
KEY IN ITEM
No.
3.5.2
–$
TOTAL 10.02
PRESS [ ] KEY
Subtotal Percent Discount
1 Obtain the subtotal amount.
• Press the SUBTOTAL and OPERATOR
(preset) keys.
➔
SUB
TOTAL
✱SUBTOTAL
Susan
PRE
OPE:01
PACK
✱TOTAL
KEY
IN ITEM
MODE
No.
2 Perform discount operation.
• Enter the discount percentage and press the
PERCENT DISCOUNT key.
TOTAL 12.02
PRESS [ ] KEY
Example: Discount rate= 5%
➔
5
✱DISCOUNT
–%
PRE
OPE:01
PACK
✱TOTAL
MODE
KEY IN ITEM
No.
3.5.3
TOTAL 12.02
TOTAL 11.42
PRESS [ ] KEY
Subtotal Special Price
1 Obtain the subtotal amount.
• Press the SUBTOTAL and OPERATOR
(preset) keys.
➔
SUB
TOTAL
✱SUBTOTAL
Susan
PRE
OPE:01
PACK
✱TOTAL
KEY
IN ITEM
MODE
No.
2 Perform special price operation.
• Enter the special pr ice and press the
DISCOUNT key.
PRESS [ ] KEY
Example: Special price = $10.50
1
0
✱DISCOUNT
✱TOTAL
MODE
KEY IN ITEM
No.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
TOTAL 12.02
5
0
PRE
OPE:01
PACK
➔
DIS
COUNT
TOTAL 10.50
PRESS [ ] KEY
page 31
3.6
Returned Item
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Obtain the subtotal amount.
• Press the SUBTOTAL and OPERATOR
(preset) keys.
➔
SUB
TOTAL
✱SUBTOTAL
Susan
OPE:01
TOTAL 12.02
2 Enter the return mode.
RE
TURN
3 Call up the returned item.
§ Entering PLU number
• Enter the PLU number and press the PLU key,
or press the Price Look-Up (preset) key.
§ Pressing PLU key
• Continue to press the PLU key until the item
to be returned is displayed on the screen.
✱RETURN : KEY IN PLU NO.
Example: Returned item = PLU no. 450
5
4
0
➔
PLU
OR
PLU
PLU
PLU
PLU
✱RETURN : SAUSAGE
➤
• Press the RETURN key.
The first sale
4 Finalize the transaction.
• Press the RETURN key again.
page 32
RE
TURN
✱SUBTOTAL
OPE:01
TOTAL 9.82
AC-3000/3000E • User’s Manual (Operator)• Rev 0
CHAPTER
4
ON-DEMAND
OPERATION
Contents
4.1
Mark Down Functions ..................... 30
4.1.1 Amount Discount ........................................... 30
4.1.2 Percent Discount ............................................ 30
4.1.3 Special Price ................................................... 30
4.2
Unit Price Override .......................... 31
4.3
Voiding the Last Transaction ......... 31
4.4
Changing from Weighed Item
to Fixed-price Item ......................... 31
4.5
Fixed Weight Override ................... 31
4.6
Date Override ................................. 32
4.7
Save ................................................. 32
4.8
Logo Print ......................................... 32
4.9
Store Name Print ............................. 33
4.10 Extra Text Print ................................. 33
4.11 POP Text Print .................................. 33
4.12 Coupon Text Print ........................... 34
4.1
Mark Down Functions
The following three mark down options are available. Only one of these three options may be used at one time.
This function must be used when the PLU is displayed on the screen.
Note: The discounted amount or entered special price must be less than displayed total price.
4.1.1
Amount Discount
1 Enter the discount amount.
Example: Discount amount = $0.50
§ Entering discount amount
• Enter the amount to be discounted and press
the AMOUNT DISCOUNT key.
§ Pressing AMOUNT DISCOUNT (preset) key
• Press the preset key in which the discount
amount is set.
4.1.2
5
0
➔
–$
---------------------------------------------------------------$
–0.50
Percent Discount
1 Enter the discount percentage.
§ Entering discount percentage
• Enter the percentage (1~99) to be discounted
and press the PERCENTAGE DISCOUNT
key.
Example: Discount percentage = 10%
§ Pressing PERCENT DISCOUNT (preset) key
• Press the preset key in which the percent
discount data is set.
----------------------------------------------------------------
4.1.3
1
➔
0
–%
–10%
Special Price
1 Enter the special price.
• Enter the special price and press the DISCOUNT
key.
Example: Special price = $4.50
4
page 34
5
0
➔
DIS
COUNT
AC-3000/3000E • User’s Manual (Operator)• Rev 0
4.2
Unit Price Override
This feature only functions for the weighed PLUs which are programmed to allow unit price override.
This function must be used when the PLU is displayed on the screen.
1 Enter the desired unit price.
Example: New unit price = $3.50
Note 1. If the entered unit price is not accepted at
this point, possibly the PLU has not been
programmed to allow price override.
2. A warning beep will sound when trying to
override a unit price while an item is on
the scale.
3
5
0
2 Place the item on the scale.
4.3
Voiding the Last Transaction
This function cancels the transaction of the previously printed label /receipt.
This function must be used before calling up the next PLU.
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1 Void the transaction.
• Press the VOID key.
• The previous label/receipt issue transaction
will be canceled.
• The voiding display will be displayed for a few
seconds.
4.4
VOID
FILET MIGNON
Changing from Weighed Item to Fixed-price Item
This function is used to change the mode from the weighed item to the fixed-price item.
This function must be used when the PLU is displayed on the screen.
1 Enter the fixed price.
Note: Skip this step if the fixed price is the same
as the preset unit price.
Example: Fixed price = $8.00
8
2 Press the FIXED PRICE key.
4.5
0
0
FIXED
PRICE
Fixed Weight Override
This function is used to temporarily change a fixed weight of the fixed price item.
This function must be used when the PLU is displayed on the screen.
1 Change the fixed weight.
• Enter the new weight and press the FIXED
WEIGHT key.
Example: Current weight = 50 oz.
New weight = 63 oz.
6
AC-3000/3000E • User’s Manual (Operator) • Rev 0
3
➔
FIXED
WEIGHT
page 35
4.6
Date Override
This function is used to temporarily change the current date.
This function must be used when the PLU is displayed on the screen.
Note: This function is not available when printing in the receipt mode.
1 Enter the date (MMDDYY) and press the
DATE key.
Note: The scale may be configured at installation to
override the expire date instead of the current
date.
M : Month
D : Day
Y : Year
4.7
Example: November 20, 1997
1
1
2
0
9
7
➔ DATE
Save
The SAVE key is one of the additional function options.
During a transaction, the SAVE key can be used to maintain accessed PLU data that will be used repeatedly.
This data is reset when the SAVE key is pressed again.
1 Select the desired PLU if not already
displayed.
Select PLU
2 Press the SAVE key. Then the SAVE
indicator will light.
SAVE
Note: To cancel the save mode, press the SAVE
key again.
4.8
Logo Print
With this function, a preset logo can be selected and printed on the labels. This operation should be performed
after the PLU has been accessed and before the label is issued. This function must be used when the PLU is
displayed on the screen.
Note: This function is not available when printing in the receipt mode.
1 Select the desired logo.
• Enter the logo number and press the LOGO
key.
2
➔
LOGO
Note 1. When logo printing is not needed,
press the “0” key followed by the LOGO
key.
2. Label format must be configured to
allow logo printing.
Example: Logo no. 2
page 36
AC-3000/3000E • User’s Manual (Operator)• Rev 0
4.9
Store Name Print
With this function, a preset store name can be selected and printed on the labels. This operation should be
performed after the PLU has been accessed and before the label is issued.
This function can be used at any time.
Note: This function is not available when printing in the receipt mode.
1 Select the desired store name.
➔
2
• Enter the store name number and press the
STORE NAME key.
STORE
NAME
Example: Store name no. 2
4.10 Extra Text Print
With this function, a preset extra text message can be selected and printed on the labels. This operation should
be performed after the PLU has been accessed and before the label is issued. This function must be used when
the PLU is displayed on the screen.
Note: This function is not available when printing in the receipt mode.
1 Select the desired extra text.
• Enter the extra text number and press the
EXTRA TEXT key.
0
1
➔
EXTRA
TEXT
Note: When extra text printing is not needed,
press the “0” key followed by the EXTRA
TEXT key.
Example: Extra text no. 10
4.11 POP Text Print
With this function, a preset POP text can be selected and printed on the labels. This operation should be
performed after the PLU has been accessed and before the label is issued.
This function must be used when the PLU is displayed on the screen.
Note: This function is not available when printing in the receipt mode.
1 Select the desired POP text.
• Enter the POP text number and press the POP
TEXT key.
6
➔
POP
TEXT
Note: When POP text printing is not needed,
press the “ 0 ” key followed by the POP
TEXT key.
Example: POP text no. 6
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 37
4.12 Coupon Text Print
With this function, a preset coupon text can be selected and printed on the labels. This operation should be
performed after the PLU has been accessed and before the label is issued. This function must be used when
the PLU is displayed on the screen.
Note: This function is not available when printing in the receipt mode.
1 Select the desired coupon text.
• Enter the coupon text number and press the
COUPON TEXT key.
3
0
➔
COUPON
TEXT
Note: When coupon text printing is not needed,
press the “ 0 ” key followed by the
COUPON TEXT key.
Example: Coupon text no. 30
page 38
AC-3000/3000E • User’s Manual (Operator)• Rev 0
CHAPTER
5
SUBTRACTION
Contents
5.1
Subtraction ...................................... 36
5.1
Subtraction
The subtraction is used to subtract the transacted total from the running totals. The operator has to enter the
PLU number, quantity, weight, and price. The recommended way to manage subtraction is to keep all incorrectly
produced labels in one place and subtract each label in turn.
Note: Confirm that the Operation Key Sheet, and not the Program Key Sheet, is being used for this operation.
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
1
Enter the subtraction mode.
• Enter the password follo wed by the
PROGRAM MODE key to enter the subtraction mode.
7
0
0
0
➔
PGM
MODE
✱SUBTRACTION MODE PRESS ANY KEY
Example: Password = 7 0 0 0
Note: To exit the subtraction mode, press the
PROGRAM MODE key again.
ENTER
• Press the ENTER key.
2
Enter the PLU.
• Enter the PLU number followed by the PLU
key.
✱TOTAL
MODE
ENTER PLU
NUMBER
Example: PLU no. 2
2
3
➔
PLU
Enter the quantity.
• Enter the quantity of the item (label) to be
subtracted, and press the VOID key.
✱TOTAL
000002✱ENTER
MODE QUANTITY PRESS( [ ] KEY
0)
Example: Three (3) pcs.
3
4
PRESS [ ] KEY
➔
VOID
Enter the weight.
• Enter the weight of the item (label) to be
subtracted, and press the VOID key.
✱TOTAL
MODE WEIGHT
000002✱ENTER
PRESS
KEY
( [ ]0.00)
Example: Five (5) pounds
5
Note: If a mistaken entry was made, use the
VOID key to return to the screen with
the mistake. Then enter the correct data.
page 40
0
0
➔
VOID
AC-3000/3000E • User’s Manual (Operator)• Rev 0
5
Enter the price.
• Enter the price of the item (label) to be
subtracted, and press the VOID key.
✱TOTAL
MODE PRICE
000002✱ENTER
PRESS
KEY
( [ ]0.00)
Example: $3.75
Note: If a mistaken entry was made, use the
VOID key to return to the screen with
the mistake. Then enter the correct data.
6
3
7
5
➔
VOID
Print
§ When not using the operator system,
✱TOTAL MODE [PRINT]
000002✱PRESS
PRESS
KEY
( [ ]0.00)
• Press the PRINT key.
PRINT
---------------------------------------------------------------§ When using the operator system,
✱TOTAL MODE [OPE] KEY PRESS
KEY
000002✱PRESS
( [ ]0.00)
• Press the OPERATOR (preset) key.
Susan
7
Repeat the transaction.
• Repeat steps 2 through 6 for any other items
(labels) to be subtracted.
8
Return to the initial display.
• Press the PROGRAM MODE key to return
to the initial display.
AC-3000/3000E • User’s Manual (Operator) • Rev 0
PGM
MODE
✱TOTAL
MODE
KEY
IN ITEM
No.
PRESS [ ] KEY
page 41
CHAPTER
6
TROUBLESHOOTING
Contents
6.1
Error Messages ................................ 40
6.2
How to Release Error Conditions ... 41
6.3
How to Replace Fuse ..................... 41
6.4
Other Problems ............................... 41
6.1
Error Messages
When errors occur, use the error table below to ascertain the cause of the error and to recover normal operations.
WEIGHT
ZERO
lb
NET
UNIT PRICE
SAVE
E
AC
CHARACTER OVER
$
TOTAL PRICE
$
AUTO
Capacity 30 × 0.01 lb
PLU
WEIGHT
lb
ZERO
NET
UNIT PRICE
SAVE
$
TOTAL PRICE
$
AUTO
Capacity 30 × 0.01 lb
PLU
AC
The displays shown below have both a character and a segment
display. However, the AC-3000E has only a segment display.
Error
No.
Error Message
01
IMPROPER POSITION. CHECK CASSETTE
The cassette is not in the correct position. (AC-3000 only)
02
CHARACTER OVER
PLU name has too many characters per line.
03
POP MESSAGE: OVER CHARACTER
Insufficient space for POP message.
04
AD MESSAGE: OVER CHARACTER
Extra text has too many characters per line.
06
REG. CODE: OVER CHARACTER
Insufficient space for register code.
07
STORE NAME/ADDR.: OVER CHARACTER
Store name and address have too many characters per line.
08
LABEL END
All labels have been used.
09
LABEL SIZE ERROR
Improper label size is used.
10
PRICE DISCOUNT IS TOO LARGE
The discounted price is incorrect.
11
TABLE STRUCTURE CORRUPTION
Table structure has become corrupted.
12
MAX ITEM NUMBER OVERFLOW
Maximum number of items exceeded. (receipt application only)
13
SAME OPR. TOTALING ON MAC.
An operator performed sub-total operation at a different scale.
14
SAME OPR. PROCESSING ON OTHER
The same operator code is used at a different scale.
40
MEMORY NOT INITIAL SET
Memory has not been initialized.
42
SYSTEM ERROR
A fundamental system error has occurred.
43
E2ROM NOT INITIAL SET
E2 ROM has not been initialized.
50
NO POWER SCALE
The internal cables are not properly connected.
56
REMOVE THE ITEM ON THE PLATTER
An item is on the platter when the power is turned ON.
57
REMOVE THE ITEM ON THE PLATTER
An item is on the platter when the power is turned ON.
9380
COMM. ERROR ON RESULT TRANSFER
Communication error when sending transaction data.
9330
MASTER CONNECTION ERROR
The master scale is not properly connected.
9300
SYSTEM ERROR (CHECK CABLE)
System error involving the cable has occurred.
9330
SYSTEM ERROR (CHECK MASTER SCALE)
System error involving the master terminal has occurred.
9316
MASTER IS OFF-LINE
The master scale is not on-line.
MEMORY AREA OVERFLOWED
Too much data is in the memory area.
ERROR ON COMM. CROSSOVER
The same transaction data is received by the master scale.
66
9309
Error Contents
AC-3000/3000E • User’s Manual (Operator) • Rev 0
page 43
6.2
How to Release Error Conditions
• If an error occurs for any reason, use the CLEAR key to release the error condition.
• If trouble occurs during operations and you are unable to return to normal operation, use the RESET key
to re-initialize the scale. (This operation produces the same effect as turning the power off and then
restarting.)
6.3
How to Replace Fuse
If the display does not light when the power is on, this may indicate a problem with the fuse. Use the procedure
below to check and replace the fuse.
(1) Turn off the power, and unplug the power cord from AC outlet.
(2) Use a Philips head screw driver to remove the fuse holder cover located by ON/OFF switch.
(3) Check whether or not the fuse has blown.
(4) If the fuse has blown, replace with the same type of fuse.
Good
Blown
(5) Return and secure the fuse holder cover.
(6) Plug the power cord into AC outlet, and turn on the scale.
6.4
Other Problems
• Poor printing quality.
The thermal head has become soiled. Use the supplied cleaner set to clean the printer head.
• Labels are not printed as soon as an item is placed on the weigh platter.
The scale is set in the MANUAL mode. (AUTO indicator is not lit.)
Press the PREPACK key to turn on the AUTO indicator.
• Labels are not issued.
The printing position may not be properly set. Press the PAPER FEED key to align the paper to the correct
printing position.
page 44
AC-3000/3000E • User’s Manual (Operator)• Rev 0
44 SANNO-CHO, SHOGOIN, SAKYO-KU
KYOTO, 606 JAPAN
PHONE:(075) 771-4141
FACSIMILE: (075) 751-1634
TELEX: 05422065 SCALES J
IW701P1005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement