TELINK-SNMP2 - RVR Elettronica SpA Documentation Server

TELINK-SNMP2 - RVR Elettronica SpA Documentation Server
TELINK-SNMP2
User Manual
Volume 1
Manufactured by
Italy
File Name:
TELINK-SNMP2_ING_1.1.indb
Version:
1.1
Date:
07/02/2014
Revision history
Date
Version
20/01/2012 1.0
07/02/2014 1.1
Reason
First Edition
SNMP update
Editor
J. H. Berti
J. H. Berti
TELINK-SNMP2 - User Manual
Version 1.1
© Copyright 2012-2014
R.V.R. Elettronica SpA
Via del Fonditore 2/2c - 40138 - Bologna (Italia)
Telephone: +39 051 6010506
Fax:
+39 051 6011104
Email:
[email protected]
Web:
www.rvr.it
All rights reserved
Printed and bound in Italy. No part of this manual may be reproduced,
memorized or transmitted in any form or by any means, electronic
or mechanic, including photocopying, recording or by any information storage and retrieval system, without written permission of the
copyright owner.
All other trademark, trade name or logo used are the property of their
respective owners.
TELINK-SNMP2
Table of Contents
1.
2.
3.
3.1
3.2
4.
4.1
5.
5.1
5.2
5.3
5.4
6.
6.1
6.2
6.3
7.
8.
9.
9.1
10.
Preliminary Instructions
Warranty
First Aid
Treatment of electrical shocks
Treatment of electrical Burns
Unpacking
General Description
Installation and configuration procedure
Preparation
First Power-On and Set-Up
Management Software
SNMP Telemetry
External Description
Front Panel
Rear Panel
Connector Description
Technical Specifications
Working Principles
Identification and Access to the Modules
Upper View
Hardware Restoring IP Address
User Manual
Rev. 1.1 - 07/02/14
1
1
2
2
2
3
3
4
4
6
7
22
25
25
26
27
29
30
31
31
32
i
TELINK-SNMP2
This page was intentionally left blank
ii
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
IMPORTANT
The symbol of lightning inside a triangle placed on the product, evidences the operations for
which is necessary gave it full attention to avoid risk of electric shocks.
The symbol of exclamation mark inside a triangle placed on the product, informs the user
about the presence of instructions inside the manual that accompanies the equipment, important for the efficacy and the maintenance (repairs).
1.
Preliminary Instructions
• General foreword
The equipment in object is to considering for uses,
installation and maintenance from “trained” or “qualified”
staff, they conscious of the risks connected to operate
on electronic and electrical circuits electrical.
The “trained” definition means staff with technical
knowledge about the use of the equipment and with
responsibility regarding the own safety and the other
not qualified staff safety place under his directed
surveillance in case of works on the equipment.
The “qualified” definition means staff with instruction and
experience about the use of the equipment and with
responsibility regarding the own safety and the other not
qualified staff safety place under his directed surveillance
in case of works on the equipment.
WARNING: The machine can be equipped with
an ON/OFF switch which could not remove completely
voltages inside the machine. It is necessary to
have disconnected the feeding cord, or to have
switched off the control panel, before to execute
technical operations, making sure himself that the
safety connection to ground is connected.
The technical interventions that expect the equipment
inspection with circuits under voltage must be carry out
from trained and
qualified staff in presence of a
second trained person that it is ready to intervene
removing voltage in case of need.
R.V.R. Elettronica SpA doesn’t assume responsibility for
injury or damage resulting from improper procedures or
practices by untrained/unqualified personnel in the handling
of this unit.
WIRING: This device has a connection to ground
on the power cord and on the chassis. Check that they
are correctly connected.
Operate with this device in a residential ambient can cause
radio disturbs; in this case, it can be demanded to the user
to take adequate measures.
Specifications and informations contained in this manual
are furnished for information only, and are subject to change
at any time without notice, and should not be construed
as a commitment by R.V.R. Elettronica SpA.
The R.V.R. Elettronica SpA assumes no responsability or
liability for any errors or inaccuracies that may appear in
this manual, including the products and software described
in it;and it reserves the right to modify the design and/or
the technical specifications of the product and this manual
without notice.
• Warning regarding the use designated and the use
limitations of the product.
This product is an transmitter radio indicated
for the audio broadcasting service in frequency
modulation. It uses working frequencies that are not
harmonized in the states of designated user.
The user of this product must obtain from the Authority
for spectrum management in the state of designated
user the appropriate authorization to use the radio
spectrum, before putting in exercise this equipment.
The working frequency, the transmitter power, let alone
other specifications of the transmission system are subject
to limitation and definited in the authorization obtained.
2.
Warranty
R.V.R. Electronics S.P.A. guarantees absence of
manufacturing defect and the good operation for the
products, within the provided terms and conditions.
WARNING: The equipment is not water resistant
and an infiltration could seriously compromise
its correct operation. In order to prevent fires or
electric shocks, do not expose the equipment to rain,
infiltrations or humidity.
Please read the terms carefully, because the purchase of
the product or acceptance of order confirmation, constitutes
acceptance of the terms and conditions.
Please observe all local codes and fire protection standards
during installation and use of this unit.
Warranty will be void in cases of opened products, physical
damage, misuse, modification, repair by unauthorised
persons, carelessness and using the product for other
purpose than its intended use.
WARNING: The equipment has to its inside
exposed parts to risk of electric shock, always
disconnect power before opening covers or removing
any part of this unit.
Fissures and holes are supplied for the ventilation in order
to assure a reliable efficacy of the product that for protect
itself from excessive heating, these fissures do not have
to be obstructed or to be covered. The fissures doesn’t be
obstructed in no case. The product must not be incorporated
in a rack, unless it is supplied with a suitable ventilation or
that the manufacturer’s instructions are been followed.
WIRING: This equipment can irradiate radio
frequency energyand if it’s not installed following
the instructions contained in the manual and local
regulations it could generate interferences in radio
communications.
User Manual
For the last legal terms and conditions, please visit our web
site (WWW.RVR.IT) wich may also be changed, removed
or updated for any reason without prior notice.
In case of defect, proceed like described in the following:
1
Contact the dealer or distributor where you purchased
the unit. Describe the problem and, so that a possible
easy solution can be detected.
Dealers and Distributors are supplied with all the information
about problems that may occur and usually they can repair
the unit quicker than what the manufacturer could do. Very
often installing errors are discovered by dealers.
2
If your dealer cannot help you, contact R.V.R. Elettronica
and explain the problem. If it is decided to return the
unit to the factory, R.V.R. Elettronica will mail you a
regular authorization with all the necessary instructions
to send back the goods;
3
When you receive the authorization, you can return the
unit. Pack it carefully for the shipment, preferably using
the original packing and seal the package perfectly.
The customer always assumes the risks of loss (i.e.,
Rev. 1.1 - 07/02/14
1 / 34
TELINK-SNMP2
R.V.R. is never responsible for damage or loss), until
the package reaches R.V.R. premises. For this reason,
we suggest you to insure the goods for the whole value.
Shipment must be effected C.I.F. (PREPAID) to the
address specified by R.V.R.’s service manager on the
authorization
DO NOT RETURN UNITS WITHOUT OUR
AUTHORIZATION AS THEY WILL BE REFUSED
4
Be sure to enclose a written technical report where
mention all the problems found and a copy of your
original invoice establishing the starting date of the
warranty.
Figure 5
Replacement and warranty parts may be ordered from
the following address. Be sure to include the equipment
model and serial number as well as part description and
part number.
R.V.R. Elettronica SpA
Via del Fonditore, 2/2c
40138 BOLOGNA ITALY
Tel. +39 051 6010506
3.
3.1.2
First Aid
The personnel employed in the installation, use and
maintenance of the device, shall be familiar with theory and
practice of first aid.
3.1
3.1.1
Treatment of electrical shocks
If the victim is not responsive
Follow the A-B-C’s of basic life support.
•
Place victim flat on his backon a hard
surface.
•
Open airway: lift up neck, push forehead back
3.2
3.2.1
•
In case of only one rescuer, 15 compressions
alternated to two breaths.
•
If there are two rescuers, the rythm shall be of
one brath each 5 compressions.
•
Do not interrupt the rythm of compressions
when the second person is giving breath.
•
Call for medical assistance as soon as
possible.
If victim is responsive
•
Keep them warm.
•
Keep them as quiet as possible.
•
Loosen their clothing (a reclining position is
recommended).
•
Call for medical help as soon as possible.
Treatment of electrical Burns
Extensive burned and broken skin
•
Cover area with clean sheet or cloth.
•
Do not break blisters, remove tissue, remove
adhered particles of clothing, or apply any
salve or ointment.
•
Treat victim for shock as required.
•
Arrange transportation to a hospital as quickly
as possible.
•
If arms or legs are affected keep them
elevated.
(Figure 1).
Figure 1
•
clear out mouth if necessary and observe for
breathing
•
if not breathing, begin artificial breathing
(Figure 2): tilt head, pinch nostrils, make airtight
seal, four quick full breaths. Remember mouth
to mouth resuscitation must be commenced as
soon as possible.
If medical help will not be available within an hour and
the victim is conscious and not vomiting, give him a weak
solution of salt and soda: 1 level teaspoonful of salt and
1/2 level teaspoonful of baking soda to each quart of water
(neither hot or cold).
Allow victim to sip slowly about 4 ounces (half a glass) over
a period of 15 minutes.
Discontinue fluid if vomiting occurs.
DO NOT give alcohol.
3.2.2
Figure 2
•
Check carotid pulse (Figure 3); if pulse is
absent, begin artificial circulation (Figure 4)
depressing sternum (Figure 5).
Figure 3
2 / 34
Less severe burns
•
Apply cool (not ice cold) compresses using the
cleansed available cloth article.
•
Do not break blisters, remove tissue, remove
adhered particles of clothing, or apply salve or
ointment.
•
Apply clean dry dressing if necessary.
•
Treat victim for shock as required.
•
Arrange transportation to a hospital as quickly
as possible.
•
If arms or legs are affected keep them
elevated.
Figure 4
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
4. Unpacking
The package contains:
1 TELINK-SNMP2
1 User Manual
1 Mains Power Cable
The following accessories are also available from Your R.V.R. Dealer:
•
4.1
Accessories, spare parts and cables
General Description
Note : The equipment is set to a specific configuration. The change of configuration
is possible only by RVR or expert technical staff recommended by RVR.
The TELINK-SNMP2, manufactured by R.V.R. Elettronica SpA, is an SNMP
telemetry interface via LAN that can be connected to all standard equipment
manufactured by RVR.
The TELINK-SNMP2 have been designed for installation in a 1HE box for 19”
rack.
Two major features of TELINK-SNMP2 are compact design and user-friendliness.
Design is based on a modular concept: the different functions are performed by
modules that, for the most part, are connected through male and female connectors
or through flat cables terminated by connectors. This design facilitates maintenance
and module replacement.
It also include a Web Server and SNMP agent that allows to be connected in
ethernet network and to be explored by a WEB and MIB browser.
The TELINK-SNMP2 can be connected to the internet through the utilization of
special devices properly configured. By default, the device has the 192.168.0.244
like IP address.
The power supply is galvanically isolated and the signals are filtered to have an
high immunity to RF disturbances.
Two LEDs on the front panel provide the following status indications: ON, LOCAL.
On front panel is placed also the modality selector for remote or local control
(REMOTE).
In rear panel there are ten led to a complete synoptic on the serial line traffic and
diagnosis on error type.
TELINK-SNMP2 is equipped with watchdog hardware to reset the equipment
automatically in case of abnormal stop of processor or in case of lowering below
the threshold about power supply voltage.
User Manual
Rev. 1.1 - 07/02/14
3 / 34
TELINK-SNMP2
5.
Installation and configuration procedure
This section provides a step-by-step description of equipment installation and
configuration procedure. Follow these procedures closely upon first power-on
and each time any change is made to general configuration, such as when a new
transmission station is added or the equipment is replaced.
Once the desired configuration has been set up, no more settings are required
for normal operation; at each power-up (even after an accidental shutdown),
the equipment defaults to the parameters set during the initial configuration
procedure.
The topics covered in this section are discussed at greater length in the next
sections, with detailed descriptions of all hardware and firmware features and
capabilities. Please see the relevant sections for additional details.
IMPORTANT: when configuring and testing the transmitter in which this telemetry
unit is integrated, be sure to have the Final Test Table supplied with the equipment
ready at hand throughout the whole procedure; the Final Test Table lists all
operating parameters as set and tested at the factory.
Note : all cases shown below are referred to TELINK-SNMP2 connects to a TEXLCD made by RVR.
5.1
5.1.1
Preparation
Preliminary checks
Unpack the exciter and immediately inspect it for transport damage. Ensure that
all connectors are in perfect condition.
Provide for the following (applicable to operating tests and putting into service):
√ Mains power supply, 230 VAC (-15% / +10%), with adequate earth
connection.
√ Connection cable kit request (not included):
4 / 34
•
Telemetry signal cable;
•
Ethernet cable (cable with RJ45 connector) for connection to ADSL router or
LAN network.
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.1.2
Connections
1) Connect the Remote output of transmitter to the I2C input of the TELINKSNMP2 interface, through the telemetry signal cable.
Figure 5.1
2) Connect the ETHERNET output of TELINK-SNMP2 interface to the appropriate
input of your ADSL router or LAN network. If the connecting device is different,
identify an equivalent.
3) Connect the mains cable to the relevant MAINS connector on TELINK-SNMP2
interface.
User Manual
Rev. 1.1 - 07/02/14
5 / 34
TELINK-SNMP2
5.2
First Power-On and Set-Up
Perform this procedure upon first power-up and each time you make changes to
the configuration this component is integrated into.
5.2.1
Web User Interface (WUI)
Once all connections previously described are performed, the equipment is ready
for commissioning.
The WUI (Web User Interface) allows you to adjust, modify or display the
configuration variables such as IP, netmask and gateway address. Follow the
procedure below to open the WUI:
1) Open your web browser on your PC, and connect to http://192.168.0.244
address to connect to the WUI (if LAN IP address was previously modified, it
is necessary to use the new one). At this point the following page opens.
By factory the RVR uses the following adjustments:
•
•
•
•
•
IP address:
Netmask address:
Gateway address:
Dns 1:
Dns 2:
192.168.0.244
255.255.255.0
192.168.0.1
192.168.0.250
192.168.0.250
Menu 1
Note : If address http://192.168.0.244 does not work, check and set IP address
as 192.168.0.XXX (where XXX is a figure between 0 and 255, excluding 244 that
is TELINK-SNMP2 interface default address). To change the IP address, follow
the instructions in the manual or in the online guide and technical help, specific
for the Operating System you use.
2) If you have changed the access mode , enter the User Name and Password
previously saved. Enter your credentials to log on as administrator, or
maintenance, and then click OK on the item.
6 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
Note : The username to login as a maintenance is username: user and
password: user, while the user name to login as administrator is username:
admin and password: admin.
The user names are not modifiable by the user.
Note : Login as maintenance enables only readings inside the WUI.
3) Modify the parameters in accordance with the own needs.
4) Now interface is ready to remotely read data and modify the various settings
of the equipment.
5.3
Management Software
1) After access is made, the Main menu (main page) opens and shows possible
viewing options. This picture shows the Main menu after access:
Menu 1
To enter in one of the sub-menus, select the name and then click on item to
enter.
To go back to MAIN menu, just click on logo at top left of all sub-menus.
The page that appears is divided into three frames:
1) Title: it has the logo and an identification of the current page displayed. It is
located on the top of the page.
If you still want return to the Main Menu, simply click on the logo sited in all
the submenus on top left.
2) Navigation menu: it allows you to select the page to display.
To enter into a submenu, select the name and then click on the item to enter.
3) Body: area where the page displays information about the selected menu.
4) Password: area where you can login.
User Manual
Rev. 1.1 - 07/02/14
7 / 34
TELINK-SNMP2
5.3.1
Info Menu - Maintenance
Values found here are “live readings”, and as such they can not be modified. To
change the settings, use the General menu.
This page shows the user the data of TELINK-SNMP2 interface:
Menu 2
Web Software Release
Shows the release of WEB firmware.
Web Software Date
Shows the issue date of WEB firmware.
Device Date
Shows the day stored on the equipment (dd/MM/yyyy).
Device Time
Shows the time stored on the equipment (hh:mm).
Local Date
Shows the day stored in your browser/PC (dd/MM/yyyy).
Local Time
Shows the time stored in your browser/PC (hh:mm).
Station Location
Shows the location of transmitting station.
Station Name
Shows the ID name of transmitting station.
Station Description
Shows the additional information about transmitting station.
8 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.2
Measure Menu - Maintenance
Values found here are “live readings”, and as such they can not be modified. To
change power setting use the Command menu.
The upper part allows you to enable or disable the Auto-refresh by clicking on the
relevant box.
With Auto-refresh enabled the measures are taken every 3 seconds (“Get
Data ..”) and gave available in a legible form by the current page (“Ready”).
With Auto-refresh disabled the measures are frozen (“Stopped”) at the time when
you uncheck the box and gave available in a legible form by the current page.
This page shows the user the data of the exciter connected to the TELINK-SNMP2
interface:
Menu 3
REMOTE
Shows the status of remote control.
Forward Power
Shows exciter forward power.
Reflected Power
Shows exciter reflected power.
Temperature
Shows equipment internal temperature reading.
Vpa
Ipa
Freq.
Mod.
User Manual
Shows exciter amplifier module voltage.
Shows exciter amplifier module current.
Shows operating frequency of exciter.
Shows exciter modulation.
Rev. 1.1 - 07/02/14
9 / 34
TELINK-SNMP2
PLL
Shows the lock status at frequency set by PLL.
Audio Alarm
Shows the status of an impasse due to excessive SWR.
Power Good
Shows the status of power good.
Foldback
Shows the triggered status of the foldback function (automatic reduction
of output power).
Ext R.F. Mute
Shows the status of power inhibition by an interlock signal.
Ack ON
Shows the power on status of the exciter.
Ack OFF
Shows the power off status of the exciter.
CMD ON
Not allowed.
CMD OFF
Not allowed.
10 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.3
Alarm List - Maintenance
Values found here are “live readings”, and as such they can not be modified. To
change alarms settings, use the Alarm Delete menu.
Within this menu you can display all alarms saved by the system: any new event
will automatically delete the older ones.
This page shows the user the alarms of the exciter connected to the TELINKSNMP2 interface:
Menu 4
Value
Shows progressive number for event recording.
Date
Shows the day event was recorded (dd/MM/yyyy).
Time
Shows event recording time (hh:mm).
Type
Name
User Manual
Shows the alarm code.
Shows the description for the error that led to event recording.
Rev. 1.1 - 07/02/14
11 / 34
TELINK-SNMP2
5.3.4
Password - Maintenance
This page allows the configuration of login as a maintenance of TELINK-SNMP2
interface via WUI.
Please note that the User Name (user) can not be changed.
Menu 5
Value
12 / 34
Shows and set the password for maintenance user (enables readonly parameter).
The Erase button allows you to delete the password set and restoring
the default credentials (the username to login as a maintenance is
username: user and password: user).
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.5
General Menu - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
This page not only shows the user the information about the TELINK-SNMP2
interface, but also allows setting various parameters.
Following is a description of the items that allow modification of the parameter,
with respect to the Info menu. Press the buttons to confi rm your choice; if you let
timer to time out, the parameter setting will remain as previously set.
Menu 6
Device Date/Time
Allows you to align the date and time stored in the equipment with that
of browser device, by pressing the NTP Sync. button.
Local Date/Time
Allows you to align the date and time stored in the equipment with local
Date, by pressing the Loc. Sync. button.
New Location Name
Setting of the station location. Write the place’s name (maximum of 15
characters) in the box that you want to assign, then press the Change
Location button to apply the choice.
New Station Name
Setting of the station name. Write the name (maximum of 15 characters)
in the box that you want to assign, then press the Change Name button
to apply the choice.
New Station Description
Setting of the additional information. Write the info (maximum of 15
characters) in the box that you want to assign, then press the Change
Descrip. button to apply the choice.
New Sync. Interval
Setting of time interval to adjust system clock. Write the number of
ticks (one is equivalent to 1,33 seconds) that must elapse between
User Manual
Rev. 1.1 - 07/02/14
13 / 34
TELINK-SNMP2
synchronization from a minimum of 300 to a maximum of 86400 ticks.
Set 0 to disable.
New Server Name
Setting of NTP server to adjust system clock. Write the name of NTP
server in the box that you want to assign, then press the Set Server
button to apply the choice.
5.3.6
Command Menu - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
This page not only shows the user the information about the exciter connected to
the TELINK-SNMP2 interface, but also allows setting various parameters.
The upper part allows you to enable or disable the Auto-refresh by clicking on the
relevant box.
With Auto-refresh enabled the measures are taken every 3 seconds (“Get
Data ..”) and gave available in a legible form by the current page (“Ready”).
With Auto-refresh disabled the measures are frozen (“Stopped”) at the time when
you uncheck the box and gave available in a legible form by the current page.
Following is a description of the items that allow modification of the parameter, with
respect to the Measure menu. Press the buttons to confirm your choice, if you let
timer to time out, the parameter setting will remain as previously set.
Menu 7
Freq.
CMD ON
14 / 34
Remote adjustment of exciter frequency. This value, in MHz, can be
modified according to one’s own band in 0.1 MHz steps. Press Set to
confirm the value inserted.
Enables (ON) the exciter power output. Press Set to change the logical
state of the data.
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
CMD OFF
Disables (OFF) the exciter power output. Press Set to change the logical
state of the data.
5.3.7
Alarm Delete - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
Values found here are “live readings”, and as such they can not be modified.
Within this menu you can display the last 20 alarms saved by the system: any new
event will automatically delete the older ones. Using Reset item at bottom right of
the menu, you can delete all pending alarms.
Note : The complete list of alarms, not limited to the 20 viewable through TELINKSNMP2, is available by downloading the log file.
This page shows the user the alarms of the exciter connected to the TELINKSNMP2 interface:
Menu 8
Log File
By pressing the AlmLog.log highlighted you can download onto your
PC, or browser device, the alarm list stored in TELINK-SNMP2.
20-Nov-2013_18:18 - Type 000 “Forward
Power”;
20-Nov-2013_18:20 - Type 000 “Forward
Power”;
20-Nov-2013_18:22 - Type 004 “Mains”;
Figure 5.2 - Example of AlmLog.log file
This is a little part of file (log test made during the firmware debug) that you can
be download. It shows alarms every 2 minutes.
User Manual
Rev. 1.1 - 07/02/14
15 / 34
TELINK-SNMP2
5.3.8
Password - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
This page allows the configuration of login as a maintenance or administrator of
TELINK-SNMP2 interface via WUI.
Please note that the User Name (user) and Admin name (admin) can not be
changed.
Menu 9
Value
16 / 34
Shows and set the password for maintenance and administrator user
(enables read-only parameter).
The Erase button allows you to delete the password set and restoring
the default credentials (the username to login as a maintenance is
username: user and password: user, while the user name to login as
administrator is username: admin and password: admin).
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.9
Network - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
This page not only shows the user the information about TELINK-SNMP2 interface
network connection, but also allows setting various parameters.
Press the Change Settings button then Apply Settings button to confirm selection
and be redirected to modified IP.
Menu 10
Menu 11
Note : to make changes within these sub-menus you need to have through technical
knowledge of network management. It is recommended to have changes performed
by trained or qualifi ed personnel.
IP address
Shows the number that unequivocally identifies, within a single network,
the devices connected to an IT network that uses the IP standard
(Internet Protocol).
User Manual
Rev. 1.1 - 07/02/14
17 / 34
TELINK-SNMP2
Subnet Mask
Shows the subnet mask, necessary for the computer that must
communicate with another IP address to know if it should route packages
toward the gateway of its local network or use the address of the receiver
local network.
Gateway
Shows gateway address. In simpler networks, there is only one gateway
that forwards to the internet network all the outbound traffic. In more
complicated networks where many subnets are available, each of them
refers to a gateway that will route data traffic towards the other subnets
or forward it to other gateways.
DNS1 server
Shows the first DNS server address (Domain Name System); in case the
server should change the server hosting a service, or it is necessary to
change its IP address, it is enough to change the DNS record, without
changing client settings.
DNS2 server
Shows the second DNS server address (Domain Name System); in
case the server should change the server hosting a service, or it is
necessary to change its IP address, it is enough to change the DNS
record, without changing client settings.
MAC Address
Shows the MAC (Media Access Control) address; this address is
uniquely assigned to the ethernet network card present on exciter. It
can be useful if you want to add in your router, or firewall, a list of MAC
addresses of network cards authorized to connect to the network.
New IP address
Set the new IP (Internet Protocol) number.
New Subnet Mask
Set the new subnet mask
New Gateway
Set the new gateway address.
DNS1 server
Set the new first DNS server address (Domain Name System).
DNS2 server
Set the new second DNS server address (Domain Name System).
Download MIB files
By pressing the MIB.ZIP highlighted you can download onto your PC,
or browser device, the MIB files stored in TELINK-SNMP2.
18 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.9
SNMP - Administrator
Note : Access to this menu and modifi cation of these parameters are only possible
after login with administrator rights.
This page not only shows the user the information about TELINK-SNMP2 interface
network connection, but also allows setting various parameters.
Press the Ro Comm. / RW Comm. / Trap Comm. / Trap Dest. button to change
settings, then the relative Confirm button to confirm selection.
Menu 12
Read Community
Shows the set string for Read command that allows you to monitor the
different variables of the system managed.
Write Community
Shows the set string for Write command that allows you to monitor the
different variables of the system managed.
Trap Community
Shows the set string for Trap command that allows you to monitor the
different variables of the system managed.
Trap type
Shows the trap type that can be 0 (trap) or 1 (inform).
Inform Trap type
Shows the inform trap retry number.
Inform Trap Timeout
Shows the inform trap retry timeout.
Dest. 0 trap IP , port , Ty
Shows the first trap destinations with the IP, Port and Type of trap to
which alarm warning mail messages shall be sent.
User Manual
Rev. 1.1 - 07/02/14
19 / 34
TELINK-SNMP2
Dest. 1 trap IP , port , Ty
Shows the second trap destinations with the IP, Port and Type of trap
to which alarm warning mail messages shall be sent.
Dest. 2 trap IP , port , Ty
Shows the third trap destinations with the IP, Port and Type of trap to
which alarm warning mail messages shall be sent.
Dest. 3 trap IP , port , Ty
Shows the fourth trap destinations with the IP, Port and Type of trap to
which alarm warning mail messages shall be sent.
Dest. 4 trap IP , port , Ty
Shows the fifth trap destinations with the IP, Port and Type of trap to
which alarm warning mail messages shall be sent.
New Read Community
Set the string for Read command.
New Write Community
Set the string for Write command.
New Trap Community
Set the string for Trap command.
New Trap type
Set the new Trap type (0 for Trap or 1 for Inform). This set is valid for
all trap.
New Inform Trap type
Setting of inform trap retry number. Write the number of retry from a
minimum of 1 to a maximum of 255 times.
New Inform Trap Timeout
Setting of inform trap retry timeout. Write the number of retry from a
minimum of 1 to a maximum of 255 times.
New Trap Dest N
Setting of Trap destination number. Write the number of trap destination
from a minimum of 0 to a maximum of 5.
New Trap Dest IP
Set the identification number of the IP address set to send the
TRAP signaling. It must be in dotted format XXX.XXX.XXX.XXX (ie:
192.168.0.5)
New Trap Dest Port
Set the the port number set by the TCP transmission protocol for the
TRAP signaling that configures the agent to send a special message
to the occurrence of certain events. Usuallyit is set to 162.
New Trap Dest Ena
Set the trap destination enabling (0 for Disabled or 1 for Enabled).
20 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
5.3.10
Upgrade - Administrator
This page allows the user to update the TELINK-SNMP2 interface.
Press the Send button to confirm the upgrade; press the Cancel button, the
parameter setting will remain as previously set.
Menu 13
Browse
Allows to types the full pathname directly into the input box or you can
search the update file by “Browse” capability. Once you find it, Press
Send to upgrade the TELINK-SNMP2.
Important: do not update with file not certified by RVR Elettronica.
User Manual
Rev. 1.1 - 07/02/14
21 / 34
TELINK-SNMP2
5.4
SNMP Telemetry
The SNMP interface is based on IRT-FM-Single-Transmitter-MIB and the tree
follows.
Menu 14
Note : there is a specific MIB depending on the configuration of the station.
In the IRT MIB you can power on or off the transmitter, view the state of some
parameters like TransmitterOPMode (this is the only state able to write), RFPresent,
Fault state that in the TEX correspond to Unlock state of the PLL, Warning state that
in the TEX correspond to Audio Alarm status and the Local or Remote status.
In addendum at the IRT MIB there is also an RVR-MAIN-MIB to manage the
interface information and mib2 that contain system Name and Location.
22 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
Update OID
Network parameter
Update OID
Trap param
Update OID
Agent
Force NTP
sync. call
Menu 15 - Interface-Info tree and subtree
You can change IP data, NTP data, trap data like via web interface.
Like in WEB interface to enable the new data need to send:
1) OID apply-change to update the IP information of the Ethernet interface.
2) OID rvr-trtap-process-restart to update the trap information changed.
3) OID rvr-agent-restart to update the community information changed.
You can also send a NTP synchronization request using the OID rvr-NTP-manualsync.
Menu 16 - Information/Company-info tree
User Manual
Rev. 1.1 - 07/02/14
23 / 34
TELINK-SNMP2
System Name
and Location
Menu 17 - MIB2/System tree
Menu 18 - Trap receiving
Menu 19 - Received trap details
24 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
6. External Description
This section describes the components found on the front and rear panel of
TELINK-SNMP2.
6.1
Front Panel
Figure 6.1
[1] LOCAL
[2] REMOTE
[3] ON
User Manual
Yellow LED - Lit on when the equipment is in local mode.
Switch to select the local or remote control modes.
Green LED - Lit on when the telemetry unit is feeded by mains.
Rev. 1.1 - 07/02/14
25 / 34
TELINK-SNMP2
6.2
Rear Panel
Figure 6.2
[1] GROUND
[2] FUSE BLOCK
[3]
[4]
[5]
[6]
[7]
PLUG
I2C MASTER
I2C MASTER
RS232/485
RS232
[8] Service
[9] SYNOPTIC 1
[10] SYNOPTIC 2
[11] LAN
[12] SYNOPTIC 3
26 / 34
Ground connection.
Fuse carrier.Use a screwdriver to access the fuse. Contains two
general protection fuses rated 2 A.
VDE plug for mains power supply.
DB9 female connector for I2C bus.
DB9 male connector for I2C bus.
Not used.
DB9 connector for direct serial communications in RS232 standard
for maintenance.
DB9 connector for direct serial communications in RS232 standard
for maintenance.
LEDs for information about the status of communications in RS232
and RS485 standards.
LEDs for information about the status of the card.
RJ45 connector for LAN communication.
LEDs for information about the status of ETHERNET connector.
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
6.3
6.3.1
Connector Description
I2C Connectors
Type: DB9 Male & Female
1
2
3
4
5
6
7
8
9
6.3.2
GND
SDA
SCL
N.C.
GND
N.C.
N.C.
N.C.
N.C.
RS232
Type: DB9 Male
1
2
3
4
5
6
7
8
9
6.3.3
N.C.
RxD
TxD
N.C.
GND
N.C.
N.C.
N.C.
N.C.
SERVICE
Type: DB9 female
1
2
3
4
5
6
7
8
9
User Manual
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RI
Rev. 1.1 - 07/02/14
27 / 34
TELINK-SNMP2
6.3.3
ETHERNET
Type: RJ45 female
1
2
3
4
5
6
7
8
28 / 34
TX+
TXRX+
N.C.
N.C.
RXN.C.
N.C.
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
7. Technical Specifications
Parameters
TELINK-SNMP2
Primary Power
Phisical Dimensions (W x H x D)
Weight
Environmental working temperature
Cooling type
100-240 VAC ±15% , Full-Range
GENERALS
483 x 44 x 238 mm
4 kg
-10 to + 50 °C
Convection cooling
INPUT
Analog
-
Digital/Analog
-
Relay
-
RS232
RS485
IIC BUS
Yes
RJ 45 (LAN)
Yes
OUTPUTS
INTERFACE
Yes
Yes
STANDARD COMPLIANCE
Safety
EMC
Spectrum Optimization
User Manual
EN60215:1997
EN 301 489-11 V1.4.1
-
Rev. 1.1 - 07/02/14
29 / 34
TELINK-SNMP2
8. Synoptics LED Identification
On the back of the card, visible from rear panel, are located 2 synoptics LED
panels. Information is available below.
•
SYNOPTIC 1
RX RS232
Green Led - Blinks during data reception in SERVICE
connector.
RX RS485
Green Led - Blinks during data reception in RS485 standard on
connector internally connected with Main card.
TX RS232
Green Led - Blinks during data transmission in SERVICE
connector.
TX RS485
Green Led - Blinks during data transmission in RS485 standard
on connector internally connected with Main card.
•
SYNOPTIC 2
Green Led - Lit on identifies the correct feeding of card.
Green Led - Lit on indentifies malfunctions on hardware.
Green Led - Blink identifies the proper functioning of watchdog
on card.
SNMP
•
30 / 34
Green Led - Blink during a SNMP interrogation ended
successfully.
SYNOPTIC 3
RTX
Yellow Led - Blinks during data reception on ETHERNET
connector.
LINK
Yellow Led - Blinks during data transmission on ETHERNET
connector.
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
9. Identification and Access to the Modules
The TELINK-SNMP2 is made up of various modules linked to each other through
connectors so as to make maintenance and any required module replacement
easier.
9.1
Upper View
The figure below shows the equipment upper view with the various components
pointed out.
Figure 9.1
[1]
[2]
[3]
[4]
User Manual
Panel Card
Main Card
CPU 16bit Card
WEB & SNMP Card
Rev. 1.1 - 07/02/14
31 / 34
TELINK-SNMP2
10. Hardware Restoring IP Address
Following the procedures described here below, allows you to force an hardware
reset on TELINK-SNMP2 to restore IP address to factory settings.
1) Remove mains supply and the equipment cover.
Figure 10.1
2) Put “ON” the switch number 7.
Figure 10.2
32 / 34
Rev. 1.1 - 07/02/14
User Manual
TELINK-SNMP2
3) Put “ON” the equipment and wait who the led “attention” and “snmp” alternate
blinking.
Figure 10.3
4) Put “OFF” the switch number 7 and restart the equipment.
5) Connect to equipment at default address 192.168.0.244 in WEB mode and in
the page “Network” rewrite all the parameters.
Menu 9
6) Push the button “Change Setting” and “Apply Change”.
User Manual
Rev. 1.1 - 07/02/14
33 / 34
TELINK-SNMP2
This page was intentionally left blank
34 / 34
Rev. 1.1 - 07/02/14
User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement