Protege Manual_REVL
Protege User Guide
PROTEGE PORTABLE GAS
MONITOR
087-0038
Rev L
Protege User Guide
PROTEGE PORTABLE GAS MONITOR
087-0038
Rev L
© 2011 Scott Safety. SCOTT, the SCOTT SAFETY Logo, Scott Safety Health and
Safety, Protege, Proton, Scout, Freedom, Masterdock are registered and/or
unregistered marks of Scott Technologies, Inc. or its affiliates.
All rights reserved. No part of this documentation may be reproduced in any form or
by any means or used to make any derivative work (such as translation,
transformation, or adaptation) without written permission from Scott Safety.
Scott Safety reserves the right to revise this documentation and to make changes in
content from time to time without obligation on the part of Scott Safety to provide
notification of such revision or change.
Scott Safety provides this documentation without warranty, term, or condition of any
kind, either implied or expressed, including, but not limited to, the implied warranties,
terms or conditions of merchantability, satisfactory quality, and fitness for a particular
purpose.Scott Safety may make improvements or changes in the product(s) described
in this documentation at any time.
While every effort has been made to ensure accuracy in this guide, no responsibility
can be accepted for errors or omissions. This publication is not intended to form the
basis of a contract, and the company reserves the right to amend the design, content,
and specifications of the detector without notice.
Scott Safety, 4320 Goldmine Road, Monroe, NC 28110, Telephone 800-247-7257,
FAX 704-291-8330, E-mail techsupport.scotths.us@tycoint.com, Web
www.scottsafety.com
Microsoft, Windows, Windows 2000, Windows Me, Windows XP, Windows NT,
Windows Vista, Windows 7, Internet Explorer and MS-DOS are either trademarks or
registered trademarks of Microsoft Corporation in the United States and other
countries. Solaris and JAVA are either trademarks or registered trademarks of Sun
Microsystems, Inc. All other products or service names are the property of their
respective owners.
The international transport of this device is regulated under United States export
regulations and may be regulated by the import regulations of other countries.
087-0038
Rev L
CONTENTS
About This Guide
Guide Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Using Scott Safety Electronic Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Guide Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Related Product Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Certifications and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix
Warnings and Cautions – Device Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . xx
Warnings and Cautions – Sensor Use and Care . . . . . . . . . . . . . . . . . . . . . . . . xxii
Warnings and Cautions – Battery Use and Care . . . . . . . . . . . . . . . . . . . . . . . . xxiii
Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiv
CHAPTER 1
Introduction
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CHAPTER 2
Installation
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Planning for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Verifying Items Shipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Downloading Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Charging the Battery with the Multi-Charger (Optional) . . . . . . . . . . . . . . . . . . . 8
Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the SGM software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the JAVA Runtime Environment (JRE) Software . . . . . . . . . . . . . . . . 15
Installing the Optional Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing - Device Powered Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installing - Device Powered Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disconnecting the Optional Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
CHAPTER 3
Configuration and Setup
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Configuration and Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting the Device to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Configuring the Scott Gas Monitor Software . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SGM Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SCOTT SAFETY
087-0038 REV L
VI
CONTENTS
CHAPTER 4
Operation
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD Alerts and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 5
Maintenance
Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibrating the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zero Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Span Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintaining the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX A
29
30
31
33
35
37
38
39
40
43
44
44
46
51
Specifications
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
APPENDIX B
Quick Reference
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alerts & Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powering the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daily Bump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daily Zero Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Span Gas Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX C
57
58
58
59
60
60
60
61
Sensor Information
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Sensor K-Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Gas Interferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
APPENDIX D
Support
Appendix Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
68
69
73
74
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
087-0038 REV L
SCOTT SAFETY
087-0038
Rev L
LIST OF FIGURES
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
SCOTT SAFETY
Major Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Multi-Charger Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Multi-Charger Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Multi-Charger Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Windows Vista OS Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Scott Gas Monitor Software Installation (1 of 5) . . . . . . . . . . . . . . . . . . . . . 13
Scott Gas Monitor Software Installation (2 of 5) . . . . . . . . . . . . . . . . . . . . . 13
Scott Gas Monitor Software Installation (3 of 5) . . . . . . . . . . . . . . . . . . . . . 14
Scott Gas Monitor Software Installation (4 of 5) . . . . . . . . . . . . . . . . . . . . . 14
Scott Gas Monitor Software Installation (5 of 5) . . . . . . . . . . . . . . . . . . . . . 15
JAVA JRE Software Installation (1 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
JAVA JRE Software Installation (2 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
JAVA JRE Software Installation (3 of 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Pump Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pump Displays - Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Device Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Connecting the Device to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Scott Gas Monitor (SGM) Software Home Screen . . . . . . . . . . . . . . . . . . . 24
Scott Gas Monitor (SGM) Software Settings Screen . . . . . . . . . . . . . . . . . 24
Scott Gas Monitor (SGM) Software Set Clock Screen . . . . . . . . . . . . . . . . 25
Scott Gas Monitor (SGM) Software View Log Screen. . . . . . . . . . . . . . . . . 26
LCD Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power Up Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Zero Calibration Display - In Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Zero Calibration Display - Passed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Zero Calibration Display - Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Span Calibration - Calibration Adapter Attached. . . . . . . . . . . . . . . . . . . . . 42
Span Calibration - LCD Display Sequence . . . . . . . . . . . . . . . . . . . . . . . . . 42
Bump Test - Calibration Adapter Attached . . . . . . . . . . . . . . . . . . . . . . . . . 43
Removing Device Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Removing Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Sensor Pin Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Removing Pump Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Disassembly of Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Pump Ports and Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setup Syringe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Routing the Pump Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Pump Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Connecting the Device to a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
087-0038 REV L
VIII
LIST OF FIGURES
41
42
43
087-0038 REV L
Left and Right Operation Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Span Calibration - Calibration Adapter Attached . . . . . . . . . . . . . . . . . . . . 60
Pump Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SCOTT SAFETY
087-0038
Rev L
LIST OF TABLES
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SCOTT SAFETY
Navigating Within a PDF Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Scott Safety Documentation Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Protege User Guide Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv
Certifications and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi
Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiv
Major Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Configuration and Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SGM Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
LCD Items and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Recommended Calibration and Test Matrix . . . . . . . . . . . . . . . . . . . . . . . . 39
Recommended Maintenance Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Troubleshooting Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Device Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Hydrogen Sulfide Sensor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Carbon Monoxide Sensor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Oxygen Sensor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Combustible Sensor Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Combustible Sensor K-Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Gas Interferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Applicable Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
087-0038 REV L
X
LIST OF TABLES
087-0038 REV L
SCOTT SAFETY
087-0038
Rev L
ABOUT THIS GUIDE
Guide Overview
This guide describes the steps required to use the Protege. This document is for gas
detection personnel to manage their gas monitoring device. This document contains
information on installation, configuration, operation, maintenance and
troubleshooting.
This user guide assumes a basic knowledge of gas detection procedures.
The user guide is divided into the following topics:
•
•
•
•
•
•
•
•
•
Introduction
Installation
Configuration and Setup
Operation
Maintenance
Quick Reference
Specifications
Sensor Information
Support
Warning: Read, understand and follow the entire content of this guide prior to use.
Failure to do so may result in serious injury or death.
SCOTT SAFETY
087-0038 REV L
XII
ABOUT THIS GUIDE
Using Scott Safety
Electronic Documents
Scott Safety electronic documents are provided as PDF files. Open and view them
using the Adobe® Acrobat® Reader application, version 3.0 or later. If necessary,
download the Acrobat Reader from the Adobe Systems, Inc. web site:
http://www.adobe.com/prodindex/acrobat/readstep.html
Each provided PDF file offers several ways for moving among the document’s pages,
as follows:
To move quickly from section to section within the document, use the Acrobat
bookmarks that appear on the left side of the Acrobat Reader window. The bookmarks
provide an expandable outline view of the document’s contents. To display the
document’s Acrobat bookmarks, press the “Display both bookmarks and page” button
on the Acrobat Reader tool bar.
To move to the referenced page of an entry in the document’s Contents or Index, click
on the entry itself, each of which is hyperlinked.
To follow a cross-reference to a heading, figure, or table, click the blue text.
To move to the beginning or end of the document, to move page by page within the
document, or to navigate among the pages you displayed by clicking on hyperlinks,
use the Acrobat Reader navigation buttons shown in this figure:
Beginning
of document
End of document
Previous or next hyperlink
Previous page
Next page
Table 1 summarizes how to navigate within a Scott Safety electronic document.
Table 1 Navigating Within a PDF Document
TO NAVIGATE THIS WAY
CLICK THIS
Move from section to section within the
document.
A bookmark on the left side of the Acrobat
Reader window
Move to an entry in the Table of Contents.
The entry itself
Move to an entry in the Index.
The page number
Move to an entry in the List of Figures or
List of Tables.
The Figure or Table number
Follow a cross-reference (highlighted in
blue text).
The cross-reference text
Move page by page.
The appropriate Acrobat Reader navigation
buttons
Move to the beginning or end of the
document.
The appropriate Acrobat Reader navigation
buttons
Move backward or forward among a series The appropriate Acrobat Reader navigation
of hyperlinks you have selected.
buttons
087-0038 REV L
SCOTT SAFETY
Guide Conventions
Guide Conventions
xiii
The following visual elements are used throughout this guide, where applicable:
Warning: This icon and text indicate a potentially hazardous situation, which, if not
avoided, could result in death or injury.
Caution: This icon and text indicates a potentially dangerous procedure. Instructions
contained in the warning must be followed. Failure to do so may result in damage to
the device.
This icon and text indicate the possibility of electrostatic discharge (ESD) in a
procedure that requires the reader to take the proper ESD precautions.
This icon and text designates information of special note.
SCOTT SAFETY
087-0038 REV L
XIV
ABOUT THIS GUIDE
Related Product
Documentation
Table 2 lists the Scott Safety Family documentation set.
33339
Table 2 Scott Safety Documentation Set
DOCUMENT NAME
PURPOSE
Protege Masterdock
Covers use, operation and maintenance.
Docking Station Manual
087-0038 REV L
DOCUMENT ID
087-0045
SCOTT SAFETY
Revision History
Revision History
xv
Table 3 shows the revision history for this guide, providing a description of the
changes.
Table 3 Protege User Guide Revision History
REVISION CHANGE
K
Added record of revisions, updated parts list, updated toxic gas interference
table, added Microsoft Windows® 7 as new OS for the SGM software, added a
Note about powering down the device prior to new calibration values being
saved, updated company name, copyright and contact information, updated
content for ease of use and made various corrections throughout. Updated
certifications and approvals section. Updated part numbers. Updated cross
references, tables, figures and headings. As well as, other related maintenance
items.
L
• Re-structured entire manual.
• About This Guide chapter – Added IEC pending approval, Gost approval,
•
•
•
•
•
•
•
•
•
SCOTT SAFETY
Chinese approval, CSA approval and updated Inmetro approval. Added
Protege Masterdock Docking Station Manual to related documents table.
Added European disposal requirements. Added a caution not to operate
device within 1 to 2’ of a high-powered portable radio.
Introduction chapter – Added content about Protege Masterdock Docking
Station. Changed data log up to events from 4000 to 7000. Added 12 hours
typical run time with pump.
Installation chapter – Added content about downloading Scott Gas Monitor
(SGM) software from our Web site, un-installing lower version of SGM and
added content about Multi-Charger. Added requirement for JRE 32-bit
software. Added details for Windows 7 64-bit OS and for Windows Vista.
Added details about administrator privileges.
Configuration and Setup chapter – Updated SGM Home Tab screen to
include Portuguese button.
Maintenance chapter – Corrected location of Inlet and Outlet Ports in figure.
Bump testing section, changed 10% to +/-20% regarding verification of
readings. Added troubleshooting information related to exposure to
high-powered portable radios.
Specifications appendix – Added Data Log Event value. Added Nominal
Voltage value. Corrected CO Sensor range.
Quick Reference appendix – Added to manual.
Support appendix – Added more part numbers with photos to parts list.
Added combustible sensor (CSA) part number. Added two new Calibration
kits.
Added Scott Safety branding items and updated URL for SGM downloads.
Updated cross references, tables, figures and headings. As well as, other
related maintenance items.
087-0038 REV L
XVI
ABOUT THIS GUIDE
Certifications and
Approvals
Table 4 shows the device has been tested and complies with the following directives,
standards, or standardized documents.
Table 4 Certifications and Approvals
SYMBOL
SPECIFIC
DIRECTIVES,
STANDARDS
SKELMER
MONROE, SDALE,
US
UK
FACTORY FACTORY
SHANGHA
I, CHINA
FACTORY
UL913
Applicable N/A
N/A
CSA C22.2 No.
Applicable N/A
152-M1984
CSA C22.2 No. 157-92
CSA C22.2 No. 0-M91
N/A
CLASS I DIVISION 1
GROUPS A B C D
Ambient temperature:
-20°C to +50°C
CLASS I DIVISION 1
GROUPS A B C D T4
Ambient temperature:
-20°C to +50°C
Intrinsically Safe
Sècurité Intrinsèque
Maybe used with Pump
P/N 096-3259
EN 60079-0
EN 60079-1
EN 60079-11
Applicable Applicable N/A
Ex d ia IIC T4
DEMKO 08 ATEX
0813482X
Ambient temperature:
-20°C to +50°C
*See Special Conditions
for Safe Use
087-0038 REV L
SCOTT SAFETY
Certifications and Approvals
xvii
Table 4 Certifications and Approvals (continued)
SYMBOL
SPECIFIC
DIRECTIVES,
STANDARDS
IEC 60079-0
IEC 60079-1
IEC 60079-11
SKELMER
MONROE, SDALE,
US
UK
FACTORY FACTORY
SHANGHA
I, CHINA
FACTORY
Applicable Applicable N/A
Ex d ia IIC T4
IECEx (Pending)
Ambient temperature:
-20°C to +50°C
*See Special Conditions
for Safe Use
INMETRO Portaria 83 Applicable N/A
IEC 60079-0
IEC 60079-1
IEC 60079-11
N/A
BR-Ex d ia IIC T4
10/UL-BRCO-0009X
10/UL-BRCO-0010X
Ambient temperature:
-20°C to +50°C (Protege)
0°C to +45°C
(Accessories)
*See Special Conditions
for Safe Use
GOST R 52350.0
GOST R 52350.1
GOST R 52350.11
N/A
Applicable N/A
GB3836.1
GB3836.2
GB3836.4
N/A
N/A
Ex d ia IIC T4
POCC GB.ГБ05.B03231
Ambient temperature:
-20°C to +50°C
*See Special Conditions
for Safe Use
Applicable
Ex iad II CT4
GYJ011153X
*See Special Conditions
for Safe Use
SCOTT SAFETY
087-0038 REV L
XVIII ABOUT THIS GUIDE
Table 4 Certifications and Approvals (continued)
SYMBOL
SPECIFIC
DIRECTIVES,
STANDARDS
SKELMER
MONROE, SDALE,
US
UK
FACTORY FACTORY
SHANGHA
I, CHINA
FACTORY
Note: This table indicates all applicable certifications and approvals on a factory basis.
However, it does not mean that each individual device has all of the indicated certifications
and approvals for that particular factory. Check your particular device for its certifications
and approvals.
*Special Conditions for Safe Use: The Protege is intended only for use with the
charger/communication board, optional pump assembly, and optional Protege
Multi-Charger.
087-0038 REV L
SCOTT SAFETY
General Safety Information
General Safety
Information
xix
Ensure you adhere to the following for your safety.
Warning: Read and follow the entire content of this guide prior to use. Failure to do
so may result in serious injury or death.
Warning: All individuals who have or will have responsibility for using or testing this
product must read and understand the contents of this manual. The product will
perform as designed only if used and tested in accordance with the manufacturer's
instructions. Failure to follow manufacturer's instructions will render the warranty
and approvals null and void. failure to follow these instructions may also result in
serious injury or death.
Scott Safety can take no responsibility for use of its equipment if it is not used in
accordance with the instructions. If further operational or maintenance details are
required but not provided in this guide, contact Scott Safety or their agent.Scott Safety
shall not be liable for any incidental or consequential damages in connection with any
modifications, errors or omissions in this guide.
All pertinent state, regional, and local safety regulations must be observed when
installing and using this product. For reasons of safety and to assure compliance with
documented system data, repairs to components should be performed only by the
manufacturer.
Additionally, industry standards, codes, and legislation are subject to change. Updated
copies should be obtained by users to ensure the most recently issued regulations,
standards and guidelines are available.
All pertinent state, regional, and local safety regulations must be observed when
handling and disposing of hazardous material, Toxic (E-Chem) Sensors, batteries and
other similar items that may fall under the classification of hazardous material.
The Electrical, Electronic and Battery elements of this product must not be disposed
of via municipal waste streams; they should be delivered to collection facilities.
Information on collection facilities is given by the local authorities or importer's
representative. Correct disposal will contribute to recycling of materials and prevent
negative consequences for the environment.
For products sold in Europe, the end of life procedures for Battery operated Electronic
products must comply with the RoHS Directive 2002/95/EC, the WEEE Directive
2002/96/EC and the Battery Directive 2006/66/EC. These directives dictate how to
dispose of the electronic and battery elements of the product after use. For Protégé
products sold in the UK only, Scott Safety Ltd has provided a collection service. This
service can be accessed by Telephoning Customer Services on 01695 711711 who will
be happy to assist. Please do not send products back to Scott. In other parts of Europe,
other systems are in place. Please contact your local provider of Scott products for
more details.
Only use Scott Safety approved replacement parts.
SCOTT SAFETY
087-0038 REV L
XX
ABOUT THIS GUIDE
Warnings and
Cautions – Device Use
and Care
Ensure you follow the applicable warnings and cautions indicated here.
Warning: This equipment must be operated and serviced by qualified personnel only.
Read and understand the guide completely before operating or servicing. Qualified
personnel as defined according to local, county, state, federal and individual company
standards.
Warning: When in doubt vacate the area immediately. You should vacate the area
immediately should the device indicate a warning or alarm condition. You should
know, understand and follow your company's safety protocols.
Warning: Ensure the atmosphere is free from combustible and/or toxic gases prior to
starting any of the procedures.
Warning: When the primary device is off line, ensure you have another online device
to actively detect gases. The device may be off line due to such activities, like but not
limited to, calibration, installation, maintenance, troubleshooting, configuration,
wiring and other activities.
Warning: If the device does not function as described herein, remove from service and
mark for maintenance. Only use Scott Safety replacement parts.
Warning: Only use the device to monitor the atmosphere for the gases and
concentrations for which it is set-up to detect.
Warning: To prevent ignition of an explosive atmosphere, read and adhere to the
manufacturer's live maintenance procedures.
Warning: Read this manual for intrinsic safety precautions. Substitution of
components may impair intrinsic safety, resulting in serious injury or death.
Warning: To prevent ignition of a hazardous atmosphere, the device must be charged
in an area known to be nonhazardous.
Warning: Pump activation is verified after the block pump, clear pump commands
have been completed. Connecting a pump to the device when the device is already
powered on requires pushing the left button to begin activation.
Warning: A high off-scale reading may indicate explosive concentration.
Warning: Perform a bump test every day. Failure to perform a daily functional test
could lead to serious injury or death.
Caution: Device will not operate without power applied. Thus, it only detects gases
while powered.
Caution: Periodically test for correct operation of the system's alarm events by
exposing the device to a targeted gas concentration above the high alarm set point.
087-0038 REV L
SCOTT SAFETY
Warnings and Cautions – Device Use and Care
xxi
Caution: Calibration is critical. Calibration should be performed periodically that
takes into account device use and environment conditions. Calibrate with known
target gas at start-up and check on a regular schedule. The device should always be
re-calibrated after exposure to high concentrations of toxic or combustible gases or
vapors.
Caution: Verify the gas inlet ports are free of dirt and debris prior to use.
Caution: No gas detections are made while in the set-up mode.
Caution: Do not expose the detector to severe mechanical or electrical shock. Always
conduct device startup and bump test procedures after such exposure to verify the
device's operation and accuracy.
Caution: To ensure proper readings, do not operate the device within 1 to 2’ of a
high-powered portable radio. The radio keying results in reading fluctuations, as well
as, alarm & vibration activations. If this does occur, perform a Bump Test of the
device prior to putting back into service.
SCOTT SAFETY
087-0038 REV L
XXII
ABOUT THIS GUIDE
Warnings and
Cautions – Sensor
Use and Care
Ensure you follow the applicable warnings and cautions indicated here.
Warning: Extended exposure of the detector to high concentrations of toxic or
combustible gases may result in degraded sensor performance. If an alarm occurs due
to high concentration of combustible gases, exit to a safe area, then recalibrate the
device or, if needed, replace the sensor.
Warning: The combustible sensor requires 10% oxygen in the atmosphere to operate.
If you are unaware of the oxygen concentration or if the oxygen concentration is
below 10% do not use the device to monitor for combustible gas concentrations.
Failure to do so may result in injury and death.
Caution: Do not use any solvents, chemicals, or polishes containing silicon
compounds to clean the detector as these can cause damage to the sensor.
Caution: Be aware of poisoned combustible sensors. The operation of catalytic type
combustible gas sensors may be seriously affected by silicones, free halogens,
halogenated hydrocarbons and metallic oxides present in the ambient air being
monitored. If the presence of any of these substances is suspected, increased frequency
of calibration verification is recommended.
Caution: Sensitivity of the combustible gas sensor can be adversely affected by
exposure to sulfur compounds, halogens, silicone or lead containing compounds, or
phosphorus containing compounds. Avoid exposure to these substances. Should the
detector be suspected of being exposed to such substances, perform a gas test to verify
its accuracy and that it is calibrated accordingly.
087-0038 REV L
SCOTT SAFETY
Warnings and Cautions – Battery Use and Care
Warnings and
Cautions – Battery
Use and Care
xxiii
Ensure you follow the applicable warnings and cautions indicated here.
Warning: Do not attempt to charge the battery cells in potentially hazardous areas.
Do not remove battery compartment, charge batteries, change batteries in anything
but a known nonhazardous environment.
Caution: No attempt should be made to alter or repair the charger.
Caution: Do not attempt to replace the device’s battery. Return to Scott Safety for
replacement or repairs.
Caution: A fully discharged battery can lead to the loss of device’s date and time
resulting in the potential for erroneous event logging data. Recharge battery when
warning displays.
Caution: Battery life (instrument run time) reduces at low temperatures.
Caution: Recharge battery pack as soon as the device indicates a low battery alarm.
SCOTT SAFETY
087-0038 REV L
XXIV ABOUT THIS GUIDE
Acronyms
Table 5 provides a quick reference for acronyms used in this guide that may be
unfamiliar.
Table 5 Acronyms
087-0038 REV L
ACRONYM
DEFINITION
AC
Alternating Current
CO
Carbon Monoxide
H 2S
Hydron Sulfide
ID
Inside Diameter
JRE
JAVA Runtime Environment
LCD
Liquid Crystal Display
LED
Light Emitting Device
LEL
Lower Explosive Level
O2
Oxygen
OD
Outside Diameter
PC
Personal Computer
ppm
Parts per million
RH
Relative Humidity
STEL
Short Term Exposure Limit
TWA
Time Weighted Average
USB
Universal Serial Bus
SCOTT SAFETY
087-0038
Chapter 1
Rev L
INTRODUCTION
Chapter Overview
This chapter covers the following topic:
•
SCOTT SAFETY
Device Overview
087-0038 REV L
2
CHAPTER 1: INTRODUCTION
Device Overview
The Protégé comes with a long life rechargeable lithium-ion battery and sensors
already installed and ready for use. The Scott Gas Monitor (SGM) software allows
modification to the device’s settings or capture data from the device once it is
installed.
Depending on the sensors it is equipped with, the multi-gas personal device is
designed for monitoring the atmosphere for potentially hazardous levels of
combustible gases, oxygen enrichment or depletion, carbon monoxide, and hydrogen
sulfide.
Gas indication displays via a direct reading backlit LCD, multiple bright LEDs, a loud
audible alarm, and a vibratory alarm. The device includes a downloadable data log for
up to 7000 events and records STEL / TWA / PEAK exposures, calibrations, and gas
values. A built-in USB port on the charging module allows the device’s data log to be
downloaded and, when used with the device’s SGM software allows you to quickly
configure its operating and alarm parameters.
An optional Sample Draw Pump is available for remote sampling, an optional
Masterdock Docking Station is available for performing automatic Bump Testing and
Calibration, as well as an optional Multi-Charger that charges up to six (6) devices
simultaneously. The optional Multi-Charger does not need to interface with a PC.
The device ships preconfigured and ready for operation using the factory default
settings. However, you my want to reconfigure some of the parameters based upon
your application. See “Configuring the Scott Gas Monitor Software” on page 23.
If you have any questions about the device or its operation contact Scott Safety. See
“Assistance” on page 68.
Figure 1 shows the major parts of the device.
087-0038 REV L
SCOTT SAFETY
Device Overview
3
Figure 1 Major Parts
1
2
3
4
5
6
7
Front View
8
9
10
11
Side View
Rear View
Table 6 lists the major parts of the device.
SCOTT SAFETY
087-0038 REV L
4
CHAPTER 1: INTRODUCTION
Table 6 Major Parts
REFERENCE
NUMBER
ITEM
087-0038 REV L
1
LED alarms (2)
2
LCD
3
Audible Alarm Port
4
Operation Button (2)
5
Threaded Port for Pump
6
Gas Inlet Port (3)
7
Power Contacts for Pump
8
Alligator Clip
9
Charge/Communication Shoe Pad
10
Calibration Adapter Receiving Pad
11
Pump Receiving Tab
SCOTT SAFETY
087-0038
Chapter 2
Rev L
INSTALLATION
Chapter Overview
This chapter covers the following topics:
•
•
SCOTT SAFETY
Planning for Installation
Installation Checklist
087-0038 REV L
6
CHAPTER 2: INSTALLATION
Planning for
Installation
Verifying Items
Shipped
This section provides the pre-installation items.
This section provides a list of the items that typically ship with the device. Ensure you
have all items, if not See “Assistance” on page 68.
•
•
•
Downloading Software
Calibration Adapter
Portable Gas Detectors CD
T-8 Torx Driver
This section describes how to obtain software.
The Scott Gas Monitor (SGM) proprietary software is a GUI that enables you to
modify the device’s settings and access the data log.
The SGM software requires the installation of Sun Microsystems® JAVA Runtime
Environment (JRE) software. If not previously installed on the PC, JRE can be
installed on the PC after installation of the SGM software.
The SGM can be downloaded from our Web site:
•
https://www.scottsafety.com/en/us/Pages/Default.aspx
The SGM also ships on the CD with the Device. Updates to the SGM are typically
posted to our Web site first then to the CD.
The Sun Microsystems® JAVA Runtime Environment (JRE) software can be
downloaded from this Web site:
•
http://www.java.com
JAVA Version 5 or greater is required.
JRE 32-bit software is required to use the SGM on Windows 7 64-bit OS. Having JRE
64-bit software on your system is allowed, but not required.
Charging the Battery
This section describes how to charge the battery.
Caution: The device’s battery must be charged prior to first use and daily after use. It
will not operate without a battery or a battery in a low state of charge.
The device is powered by a rechargeable lithium-ion battery. Typical run time is 18
hours with no pump and 12 hours with pump; however, alarming conditions reduces
operating times. Typical charge time is between 4-6 hours. Verify battery is fully
charged prior to use. Recharge battery pack as soon as the device indicates a low
battery alarm.
Battery life varies depending on the device’s use, environmental conditions, and
battery age.
087-0038 REV L
SCOTT SAFETY
Planning for Installation
7
Required items:
•
•
•
The device
AC Power Adapter
Power & USB Communication Module
Warning: Do not attempt to charge the battery cells in potentially hazardous areas.
Failure to do so could result in death or injury.
1 Plug-in the Power and USB Communications Module
2 Connect the device by sliding the connector Shoe into the device’s pad.The
device’s LCD backlighting illuminates briefly and the battery charge indication
icon begins to blink. The LCD indicates BATTERY CHARGED on the display
when the battery is fully charged. Figure 2 shows the connections and screen
displays.
Figure 2 Charging the Battery
Power & Communication
Module
AC Power Adapter
Shoe Connector Inserts
Shoe Pad at Rear of Unit
If a battery voltage becomes very low, the backlight illuminates when plugged into the
charger, however, the battery charging icon may not appear right away.
A fully discharged battery can lead to loss of the device’s DATE and TIME settings
causing erroneous logging of gas events. If DATE and TIME are lost, See
“Configuring the Scott Gas Monitor Software” on page 23.
SCOTT SAFETY
087-0038 REV L
8
CHAPTER 2: INSTALLATION
Charging the Battery
with the Multi-Charger
(Optional)
This section provides information about charging the battery when using the optional
Multi-Charger.
The Multi-Charger can be used to charge up to six (6) devices simultaneously. Unlike
the single Power and USB Communications Module, the Multi-Charger does not need
to be connected to a PC. It only function is charging the devices.
To wall-mount the Multi-Charger (if desired), use two (2) screws (#8 or #10 Head)
6.0” (15.24cm) apart. Screws should not protrude greater than 0.25” (6.35mm). See
Figure 3.
Figure 3 Multi-Charger Mounting
6”
(15.24 cm)
1.92”
(49 mm)
C
L
To use the Multi-Charger, connect the AC power source to bottom receptacle. Insert
device with the alligator clip in the up position as shown on the front of the
Multi-Charge (decal) and push the device to snap-insert in place. See Figure 4.
087-0038 REV L
SCOTT SAFETY
Planning for Installation
9
Figure 4 Multi-Charger Use
Protégé
®
Protégé
Protégé
Multi-Charger
To clean the Multi-Charger, remove the devices and disconnect from power source.
Use only a soft cloth to wipe surfaces. If necessary, a mild detergent may be used. Dry
thoroughly before applying power or replacing devices. See Figure 5.
SCOTT SAFETY
087-0038 REV L
10
CHAPTER 2: INSTALLATION
Figure 5 Multi-Charger Cleaning
Multi-Protégé
Cha
rger
Protégé
087-0038 REV L
SCOTT SAFETY
Installation Checklist
Installation Checklist
11
This section provides the installation requirements. Table 7 lists the individual items.
Table 7 Installation Checklist
Installing the SGM
software
ITEM
DETAILS
SGM software
See “Installing the SGM software” on page 11.
JAVA Runtime Environment
(JRE) software
See “Installing the JAVA Runtime Environment (JRE)
Software” on page 15.
Optional Pump
See “Installing the Optional Pump” on page 17.
This section describes the installation of the SGM.
The Scott Gas Monitor (SGM) software enables you to modify the device’s settings
and access the data log.
The SGM software requires the installation of Sun Microsystems® JAVA Runtime
Environment (JRE) software. If not previously installed on the PC, JRE can be
installed on the PC after installation of the SGM software.
PC System Requirements:
•
Operating Systems (OS): Microsoft Windows® XP, Microsoft Windows® Vista or
Microsoft Windows® 7.
•
•
JAVA Version 5 or greater
USB port
All Windows OSs require administrator privileges to install SGM, and require power
user privileges to run SGM.
Do not connect the device charger to the PC until after the (JRE) installation is
complete.
For Windows Vista, perform step 2 prior to beginning installation. For Windows 7
proceed to step 3. For Windows XP proceed to step 4.
SCOTT SAFETY
087-0038 REV L
12
CHAPTER 2: INSTALLATION
1 Prior to installing a higher version of (SGM), ensure the lower version is removed.
To remove lower version, select Start > Control Panel > Add or Remove
Programs > Scott Gas Monitor > Remove.
2 For Windows Vista OS, navigate to USER ACCOUNTS AND FAMILY SAFETY
using the control panel and proceed to remove USER ACCOUNT CONTROL
(UAC). The check box must be unchecked for UAC. Restart the PC as necessary.
See Figure 6.
3 For Windows 7 OS, navigate to USER ACCOUNTS using the control panel and
select CHANGE USER ACCOUNT CONTROL SETTINGS. Move the Selector
to the NEVER NOTIFY (lowest level position). Then hit the OK button and next
reboot your PC.
Figure 6 Windows Vista OS Only
4 After downloading the SGM, navigate to the “gasmon.msi” file on the PC and
double click it to start the installation procedure.
5 When prompted, click NEXT to proceed with installation. See Figure 7.
087-0038 REV L
SCOTT SAFETY
Installation Checklist
13
Figure 7 Scott Gas Monitor Software Installation (1 of 5)
6 When prompted, check the box to accept the terms of the License Agreement.
Click NEXT to proceed. See Figure 8.
Figure 8 Scott Gas Monitor Software Installation (2 of 5)
7 If desired, select a custom location to install the SGM software or use the default
location. Click NEXT to proceed. See Figure 9.
SCOTT SAFETY
087-0038 REV L
14
CHAPTER 2: INSTALLATION
Figure 9 Scott Gas Monitor Software Installation (3 of 5)
8 Click INSTALL and monitor installation progress. See Figure 10.
Figure 10 Scott Gas Monitor Software Installation (4 of 5)
087-0038 REV L
SCOTT SAFETY
Installation Checklist
15
9 When prompted, click FINISH to complete the installation. See Figure 11.
Figure 11 Scott Gas Monitor Software Installation (5 of 5)
Installing the JAVA
Runtime Environment
(JRE) Software
This section describes the installation of the JRE.
JAVA Runtime Environment (JRE) software must be installed to use the SGM
software.
JRE 32-bit software is required to use the SGM on Windows 7 64-bit OS. Having JRE
64-bit software on your system is allowed, but not required.
1
Navigate to the Java folder and select the JAVA installation file for the appropriate
operating system of the PC.
2 Double click the file to begin the installation process.
3 Observe the JRE installation begins. Installation files may be unpacked during an
automated process.
4 When prompted, select ACCEPT to agree to the User License Agreement and
proceed with the installation. See Figure 12.
SCOTT SAFETY
087-0038 REV L
16
CHAPTER 2: INSTALLATION
Figure 12 JAVA JRE Software Installation (1 of 3)
5 When prompted, either check (select) or un check (un select) any of the third party
software applications, such as Google Tool bar, that Sun Microsystems provides
bundled with the JRE software installation. See Figure 13.
Figure 13 JAVA JRE Software Installation (2 of 3)
Only JRE software is required to run the SGM software. Installing or not installing
any optional software on this screen will not affect operation of the SGM.
6 Click NEXT to proceed.
087-0038 REV L
SCOTT SAFETY
Installation Checklist
17
7 Observe the installation progress screen through the installation. The Installation
times varies depending on PC performance.
8 When prompted upon successful completion of the JRE software installation, click
FINISH to complete the installation. See Figure 14.
Figure 14 JAVA JRE Software Installation (3 of 3)
Installing the Optional
Pump
This section provides information on installing the optional pump when powered up
or powered down and disconnecting.
The device’s Automatic Sample Draw Pump is powered by the device’s internal
battery. Typical run time with pump is 12 hours; however, environmental conditions
and alarm conditions shorten run time. If the pump is connected to the device when
the device is powered up, it is automatically recognized.
Scott Safety recommends using the pump only when the tubing and sample draw
system including hydrophobic and particulate filters in the probe assembly are
attached to avoid possible contamination of the pump.
To troubleshoot a poorly performing pump, See “Troubleshooting the Device” on
page 51.
Required items:
•
•
SCOTT SAFETY
The device
Optional Pump
087-0038 REV L
18
CHAPTER 2: INSTALLATION
Caution: When using the sample draw pump, allow sufficient sample time based on
the length of sample tubing you are using. Allow a minimum of 1 second for every foot
of sample tubing and wait for the gas readings to stabilize. Failure to do so could lead
to inaccurate readings.
Installing - Device Powered Down
This section describes how to install the optional pump when the device is powered
down.
1 Connect the pump by inserting, at an angle, the pump's back Tab into the device's
Tab. Rotate the pump forward until the pump sits flush with the device. Tighten the
Thumb Screw into the threaded hole located on the front of the device. See
Figure 15.
Figure 15 Pump Installation
Tighten
Thumb Screw
Align Tab
2 Power on the device and allow it to run through its start-up routine. At this point,
the pump is running.
3 Upon completion of the start-up routine, the pump activates and BLOCK PUMP
displays. To block pump inlet, place a finger over the probe. Once the test is
passed, CLEAR PUMP displays. See Figure 16.
087-0038 REV L
SCOTT SAFETY
Installation Checklist
19
Figure 16 Pump Displays - Start Up
O2%
H2S ppm
PUMP
CO ppm
LEL %
If the device fails to indicate clear pump, check for any potential leaks in the
connection of the pump to the device or within the sample draw system including
hydrophobic and particulate filters in the probe assembly.
4 Remove finger from probe and the device is ready for use.
Installing - Device Powered Up
This section describes how to install the optional pump when the device is powered
up.
Warning: Pump is not automatically activated when attached to a powered on device.
You must press the Left Operation Button to begin pump activation. Failure to activate
a pump leads to unreliable monitoring that could lead to death or injury.
1 Connect the pump by inserting, at an angle, the pump's back Tab into the device's
pump receiving Tab. Rotate the pump forward until the pump sits flush with the
device. Screw the pump retaining screw into the threaded hole located on the front
of the device. See Figure 15.
2 At this point, the pump is not running. Push and hold the Left Operation Button to
activate the pump. Release the Left Operation Button when BLOCK PUMP
displays.
3 To block pump inlet, place a finger over the probe. Once the test is passed, CLEAR
PUMP displays.
If the device fails to indicate CLEAR PUMP, check for any potential leaks in the
connection of the pump to the device or within the sample draw system including
hydrophobic and particulate filters in the probe assembly.
4 Remove finger from probe and the device is ready for use.
Disconnecting the Optional Pump
This section describes how to disconnect the optional pump from the device.
1 Unscrew the pump retaining screw while continuing to hold the pump against the
device.
2 If unit is powered on, press and hold the Left Operation Button until the device
starts displaying the PEAK exposures.
If the pump alarm sounds, acknowledge by pressing and releasing the Left or Right
Operation Button, then press and hold the Left Operation Button until the device
starts displaying PEAK EXPOSURES. PEAK EXPOSURES flashes briefly before
returning to a normal monitoring display.
3 Rotate the pump backwards until it comes off the device.
SCOTT SAFETY
087-0038 REV L
20
CHAPTER 2: INSTALLATION
087-0038 REV L
SCOTT SAFETY
087-0038
Chapter 3
Rev L
CONFIGURATION AND SETUP
Chapter Overview
This chapter covers the following topic:
•
SCOTT SAFETY
Configuration and Setup Checklist
087-0038 REV L
22
CHAPTER 3: CONFIGURATION AND SETUP
Configuration and
Setup Checklist
This section provides the configuration and setup requirements. Table 8 lists the
individual items.
Table 8 Configuration and Setup Checklist
Connecting the Device
to a PC
ITEM
DETAILS
Device to PC connection
See “Connecting the Device to a PC” on page 22.
SGM software
See “Configuring the Scott Gas Monitor Software” on page 23.
SGM software (defaults)
See “SGM Defaults” on page 27.
This section describes connecting the device to a PC.
Required items:
This assumes you have already installed both the SGM and JAVA JRE software.
•
•
•
•
•
The device
A PC
USB Cable
Power & USB Communications Module
AC Power Adapter
1 Start the SGM software by double-clicking the Protégé PCI icon. The icon is
loaded onto the Desktop during a typical install of the SGM software. The Protégé
PCI icon may be located in another location if a custom installation was
performed. See Figure 17.
Figure 17 Device Icon
2 Connect the AC Power Adapter cable to the Power & USB Communications
Module, connect the USB cable to the Power & USB Communications Module,
and connect the USB cable to your PC USB cable port.
If this is the initial install of the Power & USB Communications Module, allow the PC
to load and recognize the Power & USB Communications Module before proceeding.
3 Connect the device to the Power & USB Communications Module by sliding the
connector shoe into the back of the device. See Figure 18.
087-0038 REV L
SCOTT SAFETY
Configuration and Setup Checklist
23
Figure 18 Connecting the Device to a PC
Shoe Connector
4 The SGM software confirms connection between the PC and the device via the
HOME tab. CONNECTED or PLEASE CONNECT YOUR INSTRUMENT
displays underneath the picture of the device.
Configuring the Scott
Gas Monitor Software
The SGM software provides a PC interface to the device to download the data log,
adjust settings, and establish alarm set points. Navigation of the software is
accomplished using the PC mouse and keyboard. The four (4) tabs located at the top
of the SGM are described here:
•
Home – Tab is the default screen that appears when starting the SGM software.
You may select the language to display and see the status of the connection to the
device from this tab.
•
Settings – Tab is used to change alarm settings.Tab provides a number of different
options. Alarm set points can be changed, a password can be inserted, timers can
be defined and the length of the LCD backlight can be configured.
•
Set Clock – Tab is used to set the date and time of the device. There is an option to
synchronize the time of the device with the PC for accurate time keeping ability.
•
View Log – Tab does not have any configurable options. Use it to download log
data from the device. This data can be read, saved, cleared, and recalled from
previously saved files.
The device ships preconfigured and ready for operation using the factory default
settings. However, you my want to reconfigure some of the parameters based upon
your application. Table 9 provide the default settings and ranges for the SGM’s five
(5) items under Settings. See “SGM Defaults” on page 27.
Figure 19 shows the Home Tab screen.
SCOTT SAFETY
087-0038 REV L
24
CHAPTER 3: CONFIGURATION AND SETUP
Figure 19 Scott Gas Monitor (SGM) Software Home Screen
Figure 20 shows the Settings Tab screen.
Figure 20 Scott Gas Monitor (SGM) Software Settings Screen
The following options are available:
•
•
•
Restore Default – Restores all device settings to the factory default.
Read – Uploads current device settings for review or modification.
Write – Downloads parameter changes made within the SGM software to the
connected device.
Changing settings within the SGM software does not change the settings on the device
until write has been accomplished.
•
•
087-0038 REV L
Open – Opens and displays previously saved device parameter setting profiles.
Save – Saves device parameter setting profiles.
SCOTT SAFETY
Configuration and Setup Checklist
•
CO, H2S, O2, and Combustible/LEL – Use the up and down arrows to adjust set
points for each alarm as desired.
•
Options – Provides the following items:
25
•
Password – A 4-digit password may be used to limit entry into the Span
calibration of the device. Select the check box that says USE PASSWORD and
enter a 4-digit number into the box. Once written to the device, everyone who
attempts to Span calibrate the device must enter this password. The default
setting is unchecked.
•
Enable Latching Alarms – When checked, this option requires you to
acknowledge all alarms even when the target gas concentration returns to a
non-alarm concentration level. The default setting is unchecked.
•
On/Off Hold Timer – Sets the required time in seconds for you to hold the
Operation Buttons when powering on and off the device. The default setting is
4 seconds.
Figure 21 shows the Set Clock Tab screen.
Figure 21 Scott Gas Monitor (SGM) Software Set Clock Screen
The following options are available:
SCOTT SAFETY
•
Synch with PC Clock – Allows you the option to synchronize the device’s internal
clock with the PC clock.
•
Get – Reads the time setting of the device presently connected and displays it on
the SGM Set Clock dialogue box.
•
Set – Uploads the time displayed on the SGM Set Clock dialogue box to the device
presently connected.
087-0038 REV L
26
CHAPTER 3: CONFIGURATION AND SETUP
Figure 22 shows the View Log Tab screen.
Figure 22 Scott Gas Monitor (SGM) Software View Log Screen
The following options are available:
•
•
•
•
087-0038 REV L
Read – Reads the data log of the device presently connected.
Clear – Clears the data log in the device presently connected.
Open – Opens previously saved data log text files.
Save – Saves data log data to a text file for future use.
SCOTT SAFETY
Configuration and Setup Checklist
SGM Defaults
27
Table 9 provides the default settings and ranges for the SGM’s five (5) items under
Settings.
Warning: Use of the Allow Use with Failed Sensor option is discouraged. Operating
the device with a failed sensor will not provide full monitoring capabilities. Use this
option only after careful consideration and understanding of the device’s reduced
monitoring capabilities and following local regulations. Failure to understand how
operating the device with a failed sensor may lead to death or injury.
Table 9 SGM Defaults
ITEM
SUB ITEM
RANGE
FACTORY
DEFAULT
Carbon
Monoxide
CO Low Alarm
0 to 500ppm
35ppm
CO High Alarm
0 to 500ppm
35ppm
CO STEL Alarm
0 to 250ppm
200ppm
CO TWA Alarm
0 to 100ppm
35ppm
CO Calibration Gas
Concentration
0 to 999ppm
50ppm
H2S Low Alarm
0 to 200ppm
10ppm
H2S High Alarm
0 to 200ppm
10ppm
H2S STEL Alarm
0 to 15ppm
15ppm
H2S TWA Alarm
0 to 15ppm
15ppm
H2S Calibration Gas
Concentration
0 to 500ppm
25ppm
O2 Low Alarm
0 to 25%
19.50%
O2 High Alarm
0 to 25%
23.50%
LEL Low Alarm
0 to 60%
10% LEL
LEL High Alarm
0 to 60%
10% LEL
LEL Calibration Gas
Concentration
0 to 70%
32% LEL
Hydrogen
Sulfide
Oxygen
Combustible
SCOTT SAFETY
087-0038 REV L
28
CHAPTER 3: CONFIGURATION AND SETUP
Table 9 SGM Defaults (continued)
087-0038 REV L
ITEM
SUB ITEM
Options
Password
RANGE
FACTORY
DEFAULT
1234
Backlight Auto Off/Delay
0-255secs
30secs
Silence Alarm
Yes/No
No
Calibration Period
1-180days
30days
Button Hold Timer
1-4secs
2secs
On/Off Hold Timer
0-9secs
2secs
Temp Units
Fahrenheit/
Celsius
Fahrenheit
Zero Calibration on Power-on
On/Off
Off
Use Password
Yes/No
No
Backlight Always On
Yes/No
No
Enable Latching Alarms
Yes/No
No
Require Calibration when
Overdue
Yes/No
No
Allow Use with Failed Sensor
(See WARNING above.)
Yes/No
No
Confidence Beep On
Yes/No
No
SCOTT SAFETY
087-0038
Chapter 4
Rev L
OPERATION
Chapter Overview
This chapter covers the following topics:
•
•
•
SCOTT SAFETY
Operating the Device
Powering Up
Powering Down
087-0038 REV L
30
CHAPTER 4: OPERATION
Operating the Device
This section describes the operational modes of the device. Primary User Interface
(UI) of the device is via the LCD. During operation, the LCD displays continuous data
on gas concentrations and alarm conditions. Additionally, you can monitor peak
values of gas concentrations.
At start up, the LCD shows current alarm set points for each sensor installed, current
date and time, software version installed, and when the next required calibration is
due.
Warning: If Protégé fails to respond properly upon start up, or if calibration is out of
date, do not use the device until it has been properly serviced or calibrated. Failure to
do so could result in death or injury.
Figure 23 shows the LCD items.
Figure 23 LCD Indicators
1
H2S ppm
O2%
9
2
TWA
HIGH
STEL
LOW
3
8
4
CO ppm
5
LEL %
PEAK
6
7
Table 10 lists the LCD items and their descriptions.
Warning: If device does not operate in the manner described here, do not use. Tag it
out of service. Failure to ensure it is properly operating may result in serious injury or
death.
087-0038 REV L
SCOTT SAFETY
Operating the Device
31
Table 10 LCD Items and Descriptions
REFERENCE
NUMBER
ITEM
LCD Alerts and
Displays
DESCRIPTION
1
Gas Type Label Indicates the type gas being detected. Label blinks if an
alarm.
2
TWA
3
Battery Charge Battery charge depletion is indicated as bars disappear to
the left.
4
STEL
STEL displayed when STEL alarm set points have been
reached.
5
PEAK
Indicates highest gas exposure encountered since turning
on the instrument for Combustible (LEL) and Toxic
(E-Chem) sensors; and high and low value for oxygen
sensor. Press and release the Left Button to view.
6
Heart Beat
Blinks to indicate device is in monitoring mode.
Note: Will not blink during start-up routine or calibration.
7
Alarm
Displays when alarm set points have been reached.
8
Low Alarm
Indicates low alarm point settings or when low alarms
point reached.
9
PUMP
Displays when pump is activated.
10
High Alarm
Indicates high alarm point settings or when high alarms
point reached.
Indicates TWA displayed when alarm set points have been
reached.
This section describes various alerts and displays.
•
Gas Warning and Alarm Alerts:
– Both gas warnings and alarms blink the specific gas type that is in alert.
Audible, visual, and vibrating alarms activate and the concentration/value of
the sensor in alarm is indicated.
– If a Gas Type Label blinks with no alarm present, the sensor is detecting a
negative drift. Perform a Zero Calibration to clear the drift. See “Zero
Calibration” on page 39.
– If the option to Allow Use with Failed Sensors is enabled using the SGM
software, the device displays FAL in place of the reading for that particular
sensor.
Warning: The option of Allow Use with Failed Sensors is discouraged. Operating the
device with a failed sensor will not provide full monitoring capabilities. Use this
option only after careful consideration and understanding of the device’s reduced
monitoring capabilities and following local regulations. Failure to understand how
operating the device with a failed sensor may lead to death or injury.
•
SCOTT SAFETY
Low Battery – The battery charge icon blinks and the device activates the visual,
audible, and vibratory alarms when a battery becomes low. Low battery conditions
can be silenced by pressing the left Operation Button. You should immediately exit
the environment and charge the device as soon as a low battery alarm is indicated.
087-0038 REV L
32
CHAPTER 4: OPERATION
•
Over-Range Conditions – If a sensor within the device is exposed to a target gas
concentration that exceeds the sensor’s range, the device activates its visual,
audible, and vibratory alarms and displays +++ at the sensor’s location on the
LCD. Alarm conditions clear when the gas concentration has subsided.
Warning: If an over-range condition is encountered, perform a bump test as soon as
safely possible to ensure device functionality. If the device fails the Bump Test,
perform a full calibration procedure. Failure to do so could result in inaccurate
monitoring by the device and cause death or injury.
Warning: If using the device with a failed sensor, the failed sensor reading will be
wrong, cannot be relied upon and the device should be replaced at the earliest
possible moment.
087-0038 REV L
•
Low Flow Pump Warning – Displays when airflow through the pump is
diminished or restricted and could compromise accurate readings. Device shuts
down the pump and the device goes into audible, visual, and vibratory alarm while
the PUMP icon flashes. After the cause of the low pump flow is cleared, reset the
pump by pressing and releasing the Operation Button (Left or Right).
•
Sensor Failures – FAL indicates each sensor that fails to Zero or Span Calibrate.
Should this occur, recalibrate the device. If a sensor continues to fail, replace the
sensor and recalibrate or contact an authorized service center.
SCOTT SAFETY
Powering Up
Powering Up
33
This section describes the power up sequence.
Warning: If the device does not operate in this fashion, do not use. Tag it out of
service. Failure to do so may result in serious injury or death.
1 Press and hold one (1) of the two Operation Buttons (Left or Right) until the
countdown timer has completed and RELEASE displays on the LCD. If the
Operation Button is held for 5 seconds after RELEASE displays the device will not
turn on. See Figure 24.
Figure 24 Power Up Buttons
Left and Right
Operation Buttons
If battery voltage becomes very low while powered off, the device may display
PLEASE CHARGE when attempting to power on device. Always fully charge battery
prior to use.
The countdown timer parameter varies as set using the SGM software. See
“Configuring the Scott Gas Monitor Software” on page 23.
The device starts its Power-Up Self Test Sequence once the Operation Buttons release.
This sequence consists of the following:
1
LED, vibrating, and Audible Alarm Check – All LED’s are lit, audible alarm is
sounded, and vibrating alarm is activated.
2 Software - The current version displays.
3 Date displays.
SCOTT SAFETY
4
Time displays.
5
Low Alarm settings display.
6
High alarm settings display.
7
STEL alarm setting displays.
8
TWA alarm setting displays.
087-0038 REV L
34
CHAPTER 4: OPERATION
9
Cal Due – Indicates when next calibration is due in days.
Warning: Operating a device that has exceeded its calibration date can cause false
readings of detected gases. Do not trust invalid readings obtained while device is out
of calibration. Operating a device that is out of calibration may not accurately
indicate environmental conditions which can lead to death or injury.
Warning: If CAL EXPIRED is displayed upon power on start up sequence indicating
the device does not have valid current calibration, press the Right Operation Button to
override and immediately calibrate the device. A device that has not been properly
calibrated can lead to death or injury.
Warning: Never operate the device in gas monitoring mode with the calibration
adapter attached. This can cause false readings of detected gases. Failure to do so
can lead to death or injury.
After this sequence is complete, the device resumes typical monitoring.
087-0038 REV L
SCOTT SAFETY
Powering Down
Powering Down
35
This section describes the power down sequence.
1 Press and hold both Operation Buttons (Left and Right) simultaneously until the
countdown timer completes and the LCD is blank.
When the Operation Buttons are held for 5 seconds after the LCD goes blank, the
device attempts to power back on.
The timing parameter varies as set using the SGM software. See “Configuring the
Scott Gas Monitor Software” on page 23.
SCOTT SAFETY
087-0038 REV L
36
CHAPTER 4: OPERATION
087-0038 REV L
SCOTT SAFETY
087-0038
Chapter 5
Rev L
MAINTENANCE
Chapter Overview
This chapter covers the following topics:
•
•
•
SCOTT SAFETY
Calibrating the Device
Maintaining the Device
Troubleshooting the Device
087-0038 REV L
38
CHAPTER 5: MAINTENANCE
Calibrating the Device
This section covers calibration of the device.
Warning: Operating a device that has exceeded its calibration date can cause false
readings of detected gases. Readings obtained while device is out of calibration are
invalid and could lead to death or injury.
Caution: If CAL EXPIRED displays upon power on start up sequence indicating the
device does not have valid current calibration, press the right operation button to
override and immediately calibrate the device. Failure to do could result in
inaccurate monitoring by the device sensors.
Scott Safety recognizes the potential of the device as a life saving device when
operated and maintained correctly. As such, verifying proper operation of the device
in the form of Span Calibration and daily Bump Testing is essential to ensure the
device performs as intended in a potentially hazardous environment.
The frequency at which Span Calibration and Bump Testing occur is best determined
based on local regulatory standards, company policies, and industry best practices.
Scott Safety is not responsible for setting policies or practices.
Calibration and Test methods include the following:
•
Zero Calibration — Is performed to establish baseline readings of atmospheres
that are known to be free of toxic or combustible gases.
•
Span Calibration — Is performed to ensure the device detects target gases within
specified operating parameters. Span Calibration is the adjustment of the device’s
response to match a known concentration of gas. Sensors can lose sensitivity
through normal degradation, exposure to high gas concentrations, or sensor
poisoning. Accurate calibration can be achieved only if specific concentrations of
the correct gases are used. Span Calibration should be performed when a new
sensor is installed or when the device displays CAL EXPIRED. Span Calibration
must be performed anytime a daily Bump Test fails.
•
Bump Testing — Verifies the Span Calibration by subjecting the device to a
known exposure of gas, verifying the response is within +/-20% of actual
concentration and verifies that all alarms work properly. Scott Safety recommends
the following:
– A daily Bump Test be performed prior to each day’s use and whenever the
sensor has been exposed to a high gas concentration, submerged in water, or
exposed to mechanical shock such as being dropped.
– A daily Zero Calibration be performed prior to each day’s use and when the
device displays a reading other than its baseline reading in an atmosphere
known to be free of any toxic or combustible gases. When an atmosphere is not
known to be free of toxic or combustible gases, a Zero Air calibration cylinder
may be used.
Table 11 details the recommended calibration and test items for the device.
087-0038 REV L
SCOTT SAFETY
Calibrating the Device
39
Table 11 Recommended Calibration and Test Matrix
ITEM
FREQUENCY
DETAILS
Zero Calibration
• Daily
• When baseline readings are incorrect or
See “Zero
Calibration” on
page 39.
•
Span Calibration •
•
•
Bump Test
•
•
suspect
Prior to a Span Calibration
CAL EXPIRED is displayed
After installing new sensors
When a Bump Test fails
See “Span
Calibration” on
page 40.
Daily
See “Bump Testing”
on page 43.
When a sensor is exposed to a high
concentration of gas
• When submerged in water
• When exposed to mechanical shock, such as
being dropped
Zero Calibration
This section describes how to perform Zero Calibration.
1 Verify ambient air is free of toxic or combustible gases. If air is not free or cannot
be verified free, obtain a Zero Air gas cylinder.
2 Power on the device.
3 Press and hold the Right Operation Button until PLEASE WAIT displays. It is in
progress. See Figure 25.
Figure 25 Zero Calibration Display - In Progress
Warning: To prevent an erroneous Zero Calibration from occurring, the device
displays IS AIR CLEAR? If the device is indicating a gas reading that is 50% or
higher of an alarm set point for any of the gases it is equipped to detect. You have 20
seconds to acknowledge the alert. If the alert is not acknowledged within 20 seconds,
the device powers off. Do not continue with Zero Calibration until air has been
verified free of toxic and combustible gases. Failure to properly perform a zero
calibration may result in injury or death.
Baseline readings for a Zero Calibration are 0 for H2S, CO, and LEL, and 20.9% for
O2.
SCOTT SAFETY
087-0038 REV L
40
CHAPTER 5: MAINTENANCE
4 If display indicates IS AIR CLEAR?, and atmosphere has been verified free, press
the Right Operation Button to start the Zero Calibration.
5 Wait for device to complete Zero Calibration. If passed, the LCD displays APPLY
GAS. See Figure 26.
Figure 26 Zero Calibration Display - Passed
6 Wait for device to complete Zero calibration. If failed, the LCD displays FAILED
and the appropriate failing sensor(s). See Figure 27.
Figure 27 Zero Calibration Display - Failed
7 If Span calibration is desired, continue to See “Span Calibration” on page 40.
8 If Span Calibration is not desired, either press the Left Operation Button to exit, or
allow 80 second timer to expire.
9 When the LCD displays CAL STOPPED, press either Operation Button (Left or
Right) to exit calibration mode.
Span Calibration
This section describes how to perform Span Calibration.
Warning: Read, understand and follow the instructions, including labels and MSDS
provided by the manufacturer of the calibration gas. Failure to do so may result in
injury or death.
For precise K-Factors when performing a Span Calibration of a combustible sensor.
See “Sensor K-Factors” on page 64.
087-0038 REV L
SCOTT SAFETY
Calibrating the Device
41
Equipment required:
•
Calibration gas – Verify concentration level matches detection set points of
monitor and expiration date of cylinder has not passed.
•
•
•
Tygon tubing – 2 feet of 3/16" ID
Regulator – Set to provide flow at 0.5LPM
Calibration Adapter – Included with the device
Caution: Gas must be applied at a flow rate of 0.5LPM to perform Span Calibration.
Failure to apply gas at the proper flow rate results in failed or inaccurate calibration.
The device can be Span Calibrated using either individual calibration gas cylinders
that contain one specific target gas for the sensor being calibrated or a gas mixture
cylinder that contains a mixture of each of the target gases required to calibrate each
of the sensors the device is presently configured to detect. If using individual gas
cylinders to Span Calibrate, the Span Calibration procedure must be completed for
each sensor.
The device has an automatic 80 second timer that is enabled when APPLY GAS screen
is displayed. If you are unable to apply gas to the sensors within the 80 seconds, CAL
STOPPED displays. Pressing the right or left operational button exits calibration
mode and the procedure must be repeated.
1 Verify the concentration level of the target gas in the cylinder matches the settings
of the device as set using the SGM software. See “Configuring the Scott Gas
Monitor Software” on page 23. If needed.
2
Attach the Regulator to the gas cylinder and verify cylinder pressure.
3
Connect Tygon tubing to both the Regulator and calibration adapter.
4
With the device powered on, and if not already accomplished, press and hold the
Right Operation Button until the Zero Calibration completes and APPLY GAS or
the optional password entry screen displays on the LCD.
If optional password screen is displayed, perform step 5. If not, proceed to step 6.
5 If needed, enter the 4-digit password using the Left Operation Button to scroll
through the numeric characters and the Right Operation Button to accept the entry
and move to the next character.
CAL STOPPED displays if longer than 30 seconds has passed between character
entries. Press either the left or right operation button to exit calibration mode and
restart procedure.
6 Attach the Calibration Adapter to the device and apply gas from the Regulator. See
Figure 28.
SCOTT SAFETY
087-0038 REV L
42
CHAPTER 5: MAINTENANCE
Figure 28 Span Calibration - Calibration Adapter Attached
7 For single gas cylinders, wait for the display to read CAL PASSED then APPLY
GAS. Attach Tygon tubing to next cylinder and apply gas from the Regulator.
When final gas has been applied and passed calibration, REMOVE GAS displays.
Turn off gas cylinder and remove Calibration Adapter. The device automatically
returns to gas monitoring mode. See Figure 29.
8 For gas mixture cylinders, wait for the display to read CAL PASSED then
REMOVE GAS. Turn off gas cylinder and remove Calibration Adapter. The
device automatically returns to gas monitoring mode. See Figure 29.
If you power down the device while the LCD displays CAL PASSED and remove gas
the new calibration values are not saved. Ensure you wait until the LCD returns to the
gas monitoring mode.
Figure 29 Span Calibration - LCD Display Sequence
CALIBRATE
ZERO
H2S ppm
CO ppm
LEL %
O2%
CO ppm
H2S ppm
LEL %
H2S ppm
CO ppm
087-0038 REV L
LEL %
SCOTT SAFETY
Calibrating the Device
Bump Testing
43
This section describes how to perform Bump Test.
Equipment required:
•
Calibration gas – Verify concentration level exceeds set points of monitor and
expiration date of cylinder has not passed.
•
•
•
Tygon tubing – 2 feet of 3/16" ID
Regulator – Set to provide flow at 0.5LPM
Calibration Adapter – Included with the device
1 Verify the concentration level of the target gas in the cylinder exceeds alarm
settings of the Protégé as set using the SGM software. See “Configuring the Scott
Gas Monitor Software” on page 23. If needed.
2 Attach the Regulator to the gas cylinder and verify cylinder pressure.
3 Connect Tygon tubing to both the Regulator and Calibration Adapter.
4 If installed, remove optional pump from device and restart the device.
5 Attach Calibration Adapter to device and apply gas. See Figure 30.
Figure 30 Bump Test - Calibration Adapter Attached
6 Verify device responds to target gas and activates the visual, audible, and vibrating
alarms.
7 Verify readings on the LCD within +/-20% of actual target gas concentration.
8 Turn off gas cylinder and remove Calibration Adapter.
Warning: If the device fails to activate all alarms in a timely manner, the device must
be serviced prior to usage. If the device fails to read target gas concentration within
+/-20%, perform a Span Calibration. Failure to do so could lead to death or injury.
SCOTT SAFETY
087-0038 REV L
44
CHAPTER 5: MAINTENANCE
Maintaining the
Device
This section covers maintenance of the device.Table 12 details the recommend
maintenance item for the device.
Table 12 Recommended Maintenance Matrix
ITEM
ACTIVITY
FREQUENCY
DETAILS
Sensor
Replace
Periodic
See “Replacing the Sensor” on page 44.
Pump
Clean
Periodic
See “Cleaning the Pump” on page 46.
The device comes installed with a rechargeable lithium-ion battery that must be
replaced at the factory if needed. Do not attempt to replace the device’s battery.
Contact Scott Safety if needed. See “Assistance” on page 68.
Replacing the Sensor
This section provides information about the sensors and how to replace them.
The device ships with one of the following sensor configurations:
•
•
•
A single device installed with an LEL sensor.
•
A 4 gas device installed with an O2 sensor, LEL sensor, and a Dual Tox H2S/CO
sensor.
A 2 gas device installed with an O2 sensor and an LEL sensor.
A 3 gas device installed with an O2 sensor, LEL sensor and either a CO or H2S
sensor.
Sensors may be replaced with like sensors or Dummy Plug with another Dummy
Plug. Dummy Plugs and sensors are not interchangeable.
Using a Dummy Plug, the device can be configured with an O2 sensor and LEL
sensor, or just a LEL sensor.
Required Equipment:
•
•
Replacement Sensor or Dummy Plug
T8 Torx® Driver
1 Set or verify the device is turned off.
2 Unscrew and remove the seven (7) Torx head screws from the back of the device.
See Figure 31.
087-0038 REV L
SCOTT SAFETY
Maintaining the Device
45
Figure 31 Removing Device Cover
3 Lift and firmly pull housing cover apart. Do not pull apart at an angle or by
twisting.
4 Rotate the sensor PC board over to expose the three (3) sensors. See Figure 32.
5 Unplug desired sensor and replace with new sensor.
Figure 32 Removing Sensor
Each sensor type has a unique position and pin locations to prevent sensors being
installed in wrong locations.
6 Rotate PC board back to its original position aligning the two (2) pins to their
receptacle socket. See Figure 33.
SCOTT SAFETY
087-0038 REV L
46
CHAPTER 5: MAINTENANCE
Figure 33 Sensor Pin Alignment
2 Recepticle
2 Alignment
7 Replace back cover and install the seven (7) Torx screws. Hand-tighten the screws
taking care not to over torque as this can cause damage to the device housing.
8 Use the SGM software to set or verify settings for the newly installed sensor. See
See “Configuring the Scott Gas Monitor Software” on page 23.
9 Perform Zero and Span Calibrations of the device in accordance with calibration
procedures. See “Zero Calibration” on page 39. See “Span Calibration” on
page 40.
Cleaning the Pump
This section describes how to clean the pump.
Warning: If device does not operate in the manner described, do not use. Tag it out of
service. Failure to ensure it is properly operating may result in serious injury or
death.
Required Equipment:
•
•
•
•
•
087-0038 REV L
10ml Syringe
Tygon Tubing
T8 Torx head screw driver
Isopropyl Alcohol (IPA)
Can of compressed air
SCOTT SAFETY
Maintaining the Device
•
47
Canned compressed air (Electronic Grade)
1 Using the T8 Torx head driver, remove the four (4) Torx head screws located on the
back of the pump assembly. See Figure 34.
Figure 34 Removing Pump Screws
2 Lift the back cover off the pump enclosure and remove the pump retaining plate.
This allows access to the pump. Gently lift the pump out of the pump enclosure.
See Figure 35.
Figure 35 Disassembly of Pump
Pump Retaining
Plate
Pump Access
Back Cover
3 Carefully remove the tubing from the pump ports.
Caution: Use only the minimum force necessary to remove hoses from ports. Pump
ports break easily if excessive force is used.
To easily identify hoses for reinstallation, attach locally generated labels to the hoses.
The short hose is the OUTLET and the long hose is the INLET. See Figure 36.
SCOTT SAFETY
087-0038 REV L
48
CHAPTER 5: MAINTENANCE
Figure 36 Pump Ports and Hoses
4 Connect a piece of the Tygon tubing to the syringe and draw about 3ml of
isopropyl alcohol into the tubing and syringe. See Figure 37.
Figure 37 Setup Syringe
5 Connect the syringe and Tygon tubing to the INLET port.
6 Connect another piece of Tygon tubing to the OUTLET port and run the Tygon
tubing to a catch basin such as a small cup or trash can.
7 Slowly inject the isopropyl alcohol through the pump by pressing the plunger on
the syringe.
8 Once the isopropyl alcohol is inside the pump and tubing, pump the syringe
plunger in and out 5-7 times. Then depress the syringe plunger completely to eject
the isopropyl alcohol from the pump.
9 Carefully disconnect the Tygon tubing from the pump ports.
087-0038 REV L
SCOTT SAFETY
Maintaining the Device
49
10 Use the can of compressed air to blow the excess isopropyl alcohol from the pump.
The thin tube that comes with the can of air may be helpful in directing the air
stream into the pump ports. The pump should make an audible whir as it spins.
11 Re-attach the pump tubing to the INLET (long) and OUTLET (short) ports.
12 Place the pump assembly into the enclosure with the ports positioned over top of
one another. The OUTLET port should be on top and the INLET port should be on
the bottom. Verify the wires are routed on top of the assembly. See Figure 38.
Figure 38 Routing the Pump Wires
Outlet Port
Inlet Port
Wires Routed
on Top of Pump
13 Insert the pump retaining plate.
14 Place the pump inlet barb into the pump enclosure groove. See Figure 39.
SCOTT SAFETY
087-0038 REV L
50
CHAPTER 5: MAINTENANCE
Figure 39 Pump Reassembly
Pump
Retaining
Plate
Rounded
Groove
Pump Inlet
Barb
15 Gently place the back cover onto the pump enclosure and install the four (4) Torx
head screws. Follow an X pattern to ensure that the enclosure halves are seated
together evenly.
Caution: Do not over tighten the screws. Over tightening the screws strips the holes
in the enclosure.
16 Install pump onto an operational device and verify proper flow rate is achieved.
087-0038 REV L
SCOTT SAFETY
Troubleshooting the Device
Troubleshooting the
Device
Refer to Table 13 for troubleshooting assistance.
Table 13 Troubleshooting Matrix
CAUSE
SOLUTION
Low Flow Alarm
•
•
•
•
•
•
•
•
Unexpected chattering
noise coming from pump
during operation
Pump does not run when
activated
SCOTT SAFETY
51
Check for obstructions, kinks in the hose, or other blockage
Verify no moisture has entered the hose or pump
Unscrew probe assembly and replace filter(s) in probe
Clean pump. See “Cleaning the Pump” on page 46.
Verify no moisture has entered the hose or pump
Clean pump. See “Cleaning the Pump” on page 46.
Replace pump
Verify no other alarms are active. Active alarms may inhibit
pump from powering on
• Replace pump
The pump fails the
start-up flow test
• Clean pump. See “Cleaning the Pump” on page 46.
The sample draw reading
indicates less than
300cc/min (0.3LPM)
• Clean pump. See “Cleaning the Pump” on page 46.
Device within 1 to 2’ of a
high-powered portable
radio (reading fluctuates,
alarms & vibrates)
• Perform Bump Test prior to putting device back into service.
See “Bump Testing” on page 43.
087-0038 REV L
52
CHAPTER 5: MAINTENANCE
087-0038 REV L
SCOTT SAFETY
087-0038
Appendix A
Rev L
SPECIFICATIONS
Appendix Overview
This appendix covers the following topic:
•
SCOTT SAFETY
Specifications
087-0038 REV L
54
APPENDIX A: SPECIFICATIONS
Specifications
Table 14 lists the device’s specifications. Table 15, Table 16, Table 17 and Table 18
lists the applicable sensor specifications.
Table 14 Device Specifications
DEVICE SPECIFICATIONS
Nominal Voltage
4.2VDC
Calibration
Automatic calibration and zero
Battery
Lithium ion rechargeable; ~5Hrs. charge time
Battery Life
18Hrs no pump; 12Hrs with pump
Alarms
Audible
90dB @ 6”
Visual
Wide-angle dual red alarm bars
Tactile
Data Log
Up to 7000 events
Housing
ABS/rubber over mold
Dimensions
3.26Hx2.76Wx1.16”D (8.28Hx7.01Wx2.95cmD)
Weight
7.5oz (233.28g)
Operating
Temperature
-4.0 to +122°F (-20 to +50°C)
Operating
Humidity
0 to 90% RH, Non-Condensing
EMI/RFI
EMC 89/336/EEC compliant
Table 15 Hydrogen Sulfide Sensor Specifications
HYDROGEN SULFIDE SENSOR SPECIFICATIONS
Range
0 to 500ppm
Response Time
T90 <30sec
Operating Temp.
-4.0 to +122°F (-20 to +50°C)
Humidity
15 to 90% RH, Non-Condensing
Storage Temp.
+32 to +68°F (0 to 20°C)
Sensor Cross Sensitivity Carbon Monoxide at 300ppm
087-0038 REV L
<2ppm
Sulfur Dioxide, 5ppm
~-1ppm
Nitric Oxide, 25ppm
<1ppm
Hydrogen, 10,000ppm
<10ppm
Nitrogen Dioxide, 5ppm
~ppm
SCOTT SAFETY
Specifications
55
Table 16 Carbon Monoxide Sensor Specifications
CARBON MONOXIDE SENSOR SPECIFICATIONS
Range
0 to 999pm
Response Time
T90 <250Sec
Operating Temp.
-4.0 to +122°F (-20 to +50°C)
Humidity
15 to 90% RH, Non-Condensing
Storage Temp.
+32 to +68°F (0 to 20°C)
Sensor Cross Sensitivity Filtered against H2S, 15ppm
<0.5ppm
Filtered against SO2, 5ppm
~ 0ppm
Nitric Oxide, 35ppm
<3ppm
Nitrogen Dioxide, 5ppm
-1ppm
Chlorine, 1ppm
~0ppm
Hydrogen, 100ppm
<40ppm
Ethylene, 100ppm
<50ppm
Ethanol, 200ppm
~ 0ppm
Table 17 Oxygen Sensor Specifications
OXYGEN SENSOR SPECIFICATIONS
Range
0.0 to 25.0%
Response Time
T95=15Sec
Operating Temp.
-4.0 to +122°F (-20 to +50°C)
Humidity
0 to 90% RH, Non-Condensing
Storage Temp.
+32 to +68°F (0 to 20°C)
Table 18 Combustible Sensor Specifications
COMBUSTIBLE SENSOR SPECIFICATIONS
SCOTT SAFETY
Range
0 to 80%LEL; 0 to 5.0% v/v Gas
Response Time
T50=10Sec; T90=30Sec
Operating Temp.
-40 to +392°F (-40 to +200°C)
Humidity
0 to 90% RH, Non-Condensing
Storage Temp.
+32 to +68°F (0 to 20°C)
087-0038 REV L
56
APPENDIX A: SPECIFICATIONS
087-0038 REV L
SCOTT SAFETY
087-0038
Appendix B
Rev L
QUICK REFERENCE
Appendix Overview
This appendix covers the following topics:
•
•
•
•
•
•
•
SCOTT SAFETY
Quick Setup
Alerts & Messages
Powering the Device
Daily Bump Test
Daily Zero Calibration
Span Gas Calibration
Optional Pump
087-0038 REV L
58
APPENDIX B: QUICK REFERENCE
Quick Setup
This section provides a brief amount of information for a quick setup.
1 Connect cables and Shoe Pad to Protégé. Fully charge the Protégé prior to first use.
2 Install Scott Gas Monitor software (SGM) on PC.
3 Use software to customize alarm settings and write data to monitor.
4 Remove Shoe Pad and Power On the Protege. Perform a ZERO Cal, SPAN Cal,
and daily BUMP test. See Figure 40.
Figure 40 Connecting the Device to a PC
Shoe Connector
Alerts & Messages
087-0038 REV L
This section provides a brief amount of information on alerts and messages.
•
Alarms – The device alerts you of alarm conditions through flashing LEDs, an
audible alarm, and vibration. The specific sensor will flash with a HIGH or LOW
indication on the LCD. Alarm intensity increases from a LOW to a HIGH
condition.
•
•
LowBattery – The battery icon flashes and activate the alarms.
•
Pump – Displays when pump is connected to device. Icon flashes along with
activating alarms when a low flow situation occurs.
•
Sensor Failures – FAILED indicates along with the sensor type for each sensor that
fails to ZERO or SPAN calibrate.
•
Calibration Expired – Indicates device calibration is overdue. A SPAN calibration
must be performed prior to using the device.
•
Heart Beat – Blinking indicates device is actively monitoring properly maintained
sensors.
Over-Range Conditions – Device’s sensor(s) have been exposed to +++ very high
gas concentration exceeding sensor range.
SCOTT SAFETY
Powering the Device
Powering the Device
59
This section provides a brief amount of information on powering the device up and
down.
•
Power Up – Hold down either the Left or Right Operation Button until the LCD
displays RELEASE.
•
Power Down – Push both Left and Right Operation Buttons until timer counts
down and LCD shuts down.
See Figure 41.
Figure 41 Left and Right Operation Buttons
Left and Right
Operation Buttons
SCOTT SAFETY
087-0038 REV L
60
APPENDIX B: QUICK REFERENCE
Daily Bump Test
This section provides a brief amount of information on daily bump testing.
If installed, remove optional pump. Attach the Calibration Adapter and thread
Regulator to the calibration gas cylinder. Connect tubing. Apply gas. Device should
quickly respond to the target gases and begin alarming. Verify proper operation of
alarms. If device fails to respond (or is slow) or readings are not with in 10% of the
actual gas concentration, SPAN Calibration is required. See Figure 42.
Caution: Do not operate the device with the Calibration Adapter attached.
Figure 42 Span Calibration - Calibration Adapter Attached
Daily Zero Calibration
This section provides a brief amount of information on daily zero calibration.
In clean atmosphere, press and hold the Right Operation button. Release when display
reads PLEASE WAIT. Device automatically perform ZERO calibration. Press Left
Operation button when display reads APPLY GAS to exit. See Figure 41.
Span Gas Calibration
This section provides a brief amount of information on span gas calibration.
The device’s calibration gas concentration as set in the Scott Gas Monitor (SGM)
software setting must match actual gas concentration used. Perform ZERO calibration
procedure connecting the Calibration Adapter with hose and regulator when APPLY
GAS displays. Once each sensor is calibrated, the device displays CAL PASSED then
REMOVE GAS. Remove Calibration Adapter and wait for the device’s main display
to return before turning off the device.
087-0038 REV L
SCOTT SAFETY
Optional Pump
Optional Pump
61
This section provides a brief amount of information on the Optional Pump.
Connect pump. See Figure 43. Power on the device or push the Left Operation button
to activate the pump. When BLOCK PUMP displays, place a finger over the probe
until CLEAR PUMP displays. To disconnect pump, press and hold the Left Operation
button until PEAK EXPOSURES displays. Remove pump.
Figure 43 Pump Installation
Tighten
Thumb Screw
Align Tab
SCOTT SAFETY
087-0038 REV L
62
APPENDIX B: QUICK REFERENCE
087-0038 REV L
SCOTT SAFETY
087-0038
Appendix C
Rev L
SENSOR INFORMATION
Appendix Overview
This appendix covers the following topics:
•
•
SCOTT SAFETY
Sensor K-Factors
Gas Interferences
087-0038 REV L
64
APPENDIX C: SENSOR INFORMATION
Sensor K-Factors
Table 19 provides the K-Factors referenced to methane calibration. The factors are the
typical ratios of the response to the listed gases relative to the response to methane.
The values are typical, but will vary from sensor to sensor and over the lifetime of a
given sensor. When a gas other than the calibration gas is detected, divide the reading
by the corresponding factor to estimate the actual gas concentration. For example,
propane may be detected by the device calibrated with methane. If the reading is 32%
LEL: 32% LEL Methane indicated/0.65 = 49% LEL of propane, estimated. Generally,
if there is a potential for methane in the operating environment, the instrument should
be calibrated with methane. If there also is a potential for other gases in the operating
environment, the LEL alarm level should be adjusted according to the lowest
K-Factor of the expected gases. For example, if either methane or propane may be
present, and the desired alarm is 25% LEL, calibrate the instrument with methane and
set the alarm level at (25% x 0.65 = 16% LEL). For best accuracy, calibrate the device
with a gas similar to the monitored target gas.
Table 19 Combustible Sensor K-Factors
KNOWN GAS
PRESENT
087-0038 REV L
K-FACTORS
n-Butane
0.6
Methanol
1.04
Ethane
0.8
Hydrogen
1.1
Methane
1
Propane
0.65
n-Pentane
0.5
n-Hexane
0.45
n-Octane
0.4
Ethanol
0.8
Isopropanol
0.69
Acetone
0.7
Ammonia
1.3
Toluene
0.35
Gasoline
0.6
Isobutanol
0.53
Xylene
0.49
Styrene
0.46
SCOTT SAFETY
Gas Interferences
Gas Interferences
65
There are known gas interferences to a limited number of chemical compounds.Scott
Safety attempts to identify possible gas interferences to which gas sensors may be
exposed; however, not all chemical compounds that presently exist have been tested.
Table 20 provides known toxic gas interferences.
Table 20 does not show, nor should it be implied, that no additional interferences may
occur. these selectivity ratios are used as guides only. They are not to be used as
calibration factors. The gas species’ actual cross-sensitivities may vary from the
values shown.
Table 20 Gas Interferences
SENSOR TYPES (ALL VALUES IN PPM)
Dual-Tox Sensor
CO
Interference
Gas
CO
H 2S
1
H2S
< 0.02
1
NO2
< 0.04
< 0.2
< 0.02
NO
< 0.003
SO2
CO
1
H2S
< 0.02
1
< 0.2
< 0.25
< 0.25
~ -0.2
-0.25 to 0
< -0.3
< 0.03
< 0.5
< 0.02
< 0.001
< 0.001
NH3
< 0.1
H2
~ 0.2
0.003
< 0.6
< 0.005
CL2
0
0
< 0.001
< -0.25
Key: < Less than; ~ Approximate.
For each sensor type, the table shows how 1ppm of an Interference Gas
appears on that specific sensor type. For example, 1ppm CO appears as less
than 0.02ppm on a H2S sensor.
SCOTT SAFETY
087-0038 REV L
66
APPENDIX C: SENSOR INFORMATION
087-0038 REV L
SCOTT SAFETY
087-0038
Appendix D
Rev L
SUPPORT
Appendix Overview
This appendix covers the following topics:
•
•
•
•
SCOTT SAFETY
Assistance
Parts List
Warranty Statement
Product Information
087-0038 REV L
68
APPENDIX D: SUPPORT
Assistance
Congratulations on your purchase of a Scott Safety product. It is designed to provide
you with years of reliable trouble-free service.
•
•
If you have technical questions or need support.
If you need to return a product.
Contact us using the options provided:
– By E-mail: techsupport.scotths.us@tycoint.com
– By Telephone: 1- 800-247-7257
When returning a product, contact Technical Support to obtain a Return Material
Authorization (RMA) number prior to shipping for service repairs using the contact
options.
087-0038 REV L
SCOTT SAFETY
Parts List
Parts List
69
Table 21 provides a parts list.
Table 21 Applicable Parts List
CATEGORY
Accessories
SCOTT SAFETY
ITEM
DESCRIPTION
PART NUMBER
Device Top Case Replacement 096-3249
Kit (Includes case top assembly,
sensor membranes, horn
membranes)
LCD Replacement Assembly
096-3247
Optional Automatic Draw
Pump
096-3259
Portable Gas Detectors CD
096-3366
T-8 Torx Driver
073-0324
14” Probe Assembly
093-0148
Calibration Adapter
074-0547
Optional Automatic Draw
Pump Kit (Includes pump, 10”
of tubing, and probe)
096-3271
Protege Multi-Charger
096-3283
Protege Masterdock Docking
Station
093-0526
087-0038 REV L
70
APPENDIX D: SUPPORT
Table 21 Applicable Parts List (continued)
CATEGORY
Accessories
087-0038 REV L
ITEM
DESCRIPTION
PART NUMBER
Power & USB Communication
Module
096-3257
AC Power Adapter
028-0045
International plug adapters for
AC Power Adapter (028-0045)
International:
028-0046
USB Cable
077-1353
10ML Syringe
077-0422
Carry Case
096-3273
Device Case Replacement Kit
(Includes case top assembly,
case bottom assembly, sensor
membranes, horn membranes,
M2.5x10 delt pt screw, device
serial number label and device
approvals label)
096-3248
Dummy Plug
074-0558
SCOTT SAFETY
Parts List
71
Table 21 Applicable Parts List (continued)
CATEGORY
Sensors
SCOTT SAFETY
ITEM
DESCRIPTION
PART NUMBER
Combustible Sensor
093-0231
Combustible Sensor - CSA
093-0524
Oxygen Sensor
093-0232
CO/H2S Sensor
093-0230
CO Sensor
093-0470
H2S Sensor
093-0471
087-0038 REV L
72
APPENDIX D: SUPPORT
Table 21 Applicable Parts List (continued)
CATEGORY
Calibration
Kits
(The specific
Calibration
Kit depends
on the
sensors in
your device)
ITEM
DESCRIPTION
PART NUMBER
Includes regulator, 24” tubing,
and calibration gas (CO, H2S,
Methane, O2 with balance of
N2 )
096-2506-16
Includes regulator, 24” tubing,
and calibration gas (CO,
Methane, O2 with balance of
N2 )
096-2506-18
Includes regulator, 24” tubing,
and calibration gas (H2S,
Methane, O2 with balance of
N2 )
096-2506-20
Includes regulator, 24” tubing,
and calibration gas (Methane,
with balance of air)
096-3272
Includes regulator, 24” tubing, 096-3392
and calibration gas (CO, H2S,
Propane, O2 with balance of N2)
Includes regulator, 24” tubing, 096-3393
and calibration gas (CO, H2S,
Pentane, O2 with balance of N2)
Note: For calibration equipment, contact your Scott sales representative.
087-0038 REV L
SCOTT SAFETY
Warranty Statement
Warranty Statement
73
Scott Safety (SCOTT), a division of Scott Technologies Inc. warrants the Protege
PORTABLE GAS DETECTION PRODUCTS (THE PRODUCTS) to be free from
defects in workmanship and materials for a period of two (2) years from the date of
original manufacture by SCOTT.
This warranty applies to all components of THE PRODUCTS supplied at the time of
original sale of THE PRODUCTS, EXCEPT pump and consumable filters. SCOTT
warrants pump supplied with THE PRODUCTS to be free from defects in
workmanship and materials for one (1) year from the date of original manufacture by
SCOTT.
SCOTT's obligation under this warranty is limited to replacing or repairing (at
SCOTT's option) THE PRODUCTS or components shown to be defective in either
workmanship or materials.
Only personnel of SCOTT or, when directed by SCOTT, authorized SCOTT agents
are permitted to perform warranty obligations. This warranty does not apply to defects
or damage caused by any repairs of or alterations to THE PRODUCTS made by
owner or any third party unless expressly permitted by SCOTT product manuals or by
written authorization from SCOTT.
To obtain performance under this warranty, and as a condition precedent to any duty
of SCOTT, the purchaser must return such products to SCOTT, a SCOTT authorized
distributor or a SCOTT authorized service center. See “Assistance” on page 68.
This warranty does not apply to any malfunction of or damage to THE PRODUCTS
resulting from accident, alteration, misuse, or abuse.
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIEDINCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. IN ADDITION, SCOTT EXPRESSLY DISCLAIMS
ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES IN ANY WAY CONNECTED WITH THE SALE OR USE OF SCOTT
PRODUCTS, AND NO OTHER FIRM OR PERSON IS AUTHORIZED TO
ASSUME ANY SUCH LIABILITY.
SCOTT SAFETY
087-0038 REV L
74
APPENDIX D: SUPPORT
Product Information
For general information on our products, refer to our Web site:
•
087-0038 REV L
http://www.scottsafety.com/
SCOTT SAFETY
087-0038
Rev L
INDEX
A
E
Approvals and Certifications xvi
Email
Technical Support 68
B
Battery
Charging 7
Battery Use and Care
Warnings and Cautions xxiii
Bump Test
Calibration Adapter Attached 43
Buttons
Power Up 33
C
Calibration Adapter Attached
Bump Test 43
Span Calibration 42
Certifications and Approvals xvi
Charging
Battery 7
Cleaning
Multi-Charger 10
Connecting
Device to a PC 23
D
Device
Major Parts 3
Device Cover
Removing 45
Device Icon
SGM 22
Device to a PC
Connecting 23
Device Use and Care
Warnings and Cautions xx
Disassembly
Pump 47
Display
Failed
Zero Calibration Display 40
SCOTT SAFETY
G
General Safety Information xix
Guide Conventions xiii
Guide Overview xi
H
Home Screen
Scott Gas Monitor (SGM) Software 24
http
//www.scottsafety.com/ 74
I
In Progress
Zero Calibration Display 39
Indicators
LCD 30
Installation
Pump 18
Installation Complete
JAVA JRE Software 17
Installation Completed
Scott Gas Monitor Software 15
Installation Destination Folder
Scott Gas Monitor Software 14
Installation End User License
Scott Gas Monitor Software 13
Installation Google
JAVA JRE Software 16
Installation Setup
Scott Gas Monitor Software 13
Installation Welcome
JVA JRE Software 16
087-0038 REV L
76
INDEX
JAVA JRE Software
Installation Complete 17
Installation Google 16
JVA JRE Software
Installation Welcome 16
Removing
Device Cover 45
Pump Screws 47
Sensor 45
Revision history, for this guide xv
Routing
Pump Wires 49
L
S
LCD
Indicators 30
LCD Display Sequence
Span Calibration 42
Scott Gas Monitor (SGM) Software
Home Screen 24
Set Clock Screen 25
Settings Screen 24
View Log Screen 26
Scott Gas Monitor Software
Installation Completed 15
Installation Destination Folder 14
Installation End User License 13
Installation Ready to Install 14
Installation Setup 13
Sensor
Pin Alignment 46
Removing 45
Sensor Use and Care
Warnings and Cautions xxii
Set Clock Screen
Scott Gas Monitor (SGM) Software 25
Settings Screen
Scott Gas Monitor (SGM) Software 24
Setup
Syringe 48
SGM
Device Icon
22
Span Calibration
Calibration Adapter Attached 42
LCD Display Sequence 42
Start Up
Pump Displays 19
Syringe
Setup 48
J
M
Major Parts
Device 3
Mounting
Multi-Charger
8, 8, 9, 10
Multi-Charger
Cleaning 10
Mounting 8
Use 9
P
Passed
Zero Calibration Display 40
Pin Alignment
Sensor 46
Ports and Hoses
Pump 48
Power Up
Buttons 33
Pump
Disassembly 47
Installation 18
Ports and Hoses 48
Reassembly 50
Pump Displays
Start Up 19
Pump Screws
Removing 47
Pump Wires
Routing 49
R
Ready to Install
Scott Gas Monitor Software Installation 14
Reassembly
Pump 50
Related Product Documentation xiv
087-0038 REV L
T
Technical Support
Email 68
Telephone Number 68
Web Site 68
Telephone Number
Technical Support 68
Troubleshooting 51
SCOTT SAFETY
INDEX
77
U
Use
Multi-Charger 9
Using Scott Safety Electronic Documents xii
V
View Log Screen
Scott Gas Monitor (SGM) Software 26
Vista
Windows 12
W
Warnings and Cautions
Battery Use and Care xxiii
Device Use and Care xx
Sensor Use and Care xxii
Web Site
Technical Support 68
Windows
Vista 12
Vista OS 12
Z
Zero Calibration Display
Failed 40
In Progress 39
Passed 40
SCOTT SAFETY
087-0038 REV L
78
INDEX
087-0038 REV L
SCOTT SAFETY
Monroe Corporate Center
P.O. Box 569
Monroe, NC 28111
Telephone: 800-247-7257
FAX: (704) 291-8330
Web: www.scottsafety.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising