ptz keyboard controller gs

ptz keyboard controller gs
PTZ KEYBOARD CONTROLLER
GS-KBC7
USER MANUAL
Page 1
1.
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS
should be observed.
1) All the safety and operating instructions should be read before the
appliance is operated.
2) Do not use this unit near water or watery places.
3) Operate this unit from the type of power source indicated on the marking
label or manual. When the voltage goes beyond the limited, please do not
open the unit.
4) Don’t clean it with the punchy detergent. Please use the soft cleaner, and
only clean the outer.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO
NOT REMOVE COVER(OR BACK).NO USER SERVICEABLE
PARTS INSIDE.
Please thoroughly familiarize yourself with the information in this manual prior
to installation and operation.
2.
DESCRIPTION
It can control output decoders, integrated camera, speed dome, or integrated PT
unit. It can also be used in our DVR system.
3.
Technical Parameter
1.Baud Rate: 1200bps, 2400bps, 4800bps, or 9600pbs.
2.Communication: RS-485
3.Power supply: 9VDC
4.Communication distance: max 1200m
5.Can control Max 32 speed domes.
Page 2
4.
Names and Functions of Each Parts
Rear Panel
D
C
B
A
A. Input power: Connect with DC9V power supply.
B. RS485-1: Connect with speed dome, decoder or receiver
C. RS485-2: No use.
D. RS232 connector: No use.
Front Panel
LCD DISPLAY
This displays the current address, protocol and baud rate.
1) 0~9
They are used to setup the camera address, PRESET No., and to modify
Page 3
the keyboard parameters.
When SHIFT button is in effect, it will be light.2 to 8 to 4 to 6 can also be
used to move the PT unit UP, DOWN, LEFT and RIGHT.
2) CAM
Enter the address (0-255) by the number key then press CAM key. The
number will be displayed after item CAM on the LCD.
3) MON
Selection ( Connect to Matrix )
4) CLOSE/OPEN, NEAR/FAR, and TELE/WIDE
This is used when controlling the actions of the IRIS, FOCUS, and ZOOM
of the zoom lens connected to the speed dome or PT unit. Under Camera
Mode, turn the menu by pressing WIDE and TELE, adjust the parameter
value by pressing FAR, and exit the adjusting by pressing NEAR
5) JOYSTICK
It is 2D or 3D,and used to move the speed dome or PT unit on pan or tilt
direction. The moving speed increases as the offset. Turning the knob on
the 3D joystick can control the camera TELE/WIDE.
6) MENU
Press key MENU to call the camera menu.
Exit the menu from the exit item of the camera menu (recommended) or
press key MENU again. Turn the menu by pressing WIDE and TELE,
adjust the parameter value by pressing FAR, and exit the adjusting by
pressing NEAR
7) Tour
Press key Tour, it gets turned on, and tour begins.
Press key Tour again, it gets turned off, and tour stops.
8) SCAN. (360°pan auto scan)
Press key SCAN, it gets turned on, and auto scan begins.
Press key SCAN again, it gets turned off, and auto scan stops.
Page 4
9) PATTERN
No use
10)
SHIFT
Press key SHIFT, it gets turned on, and SHIFT is in effect.
Press key SHIFT again, it gets turned off, and SHIFT is off no effect.
11)
BEFORE
No use
12)
NEXT
No use
13)
PRESET
This is used when searching for the PRESET position set up in the speed
dome or receiver. Input the Preset No. in the Number area, and press key
PRESET to call it. If succeed, the number input area will reset automatically.
PRESET NO. (1-32) (34-66)
14) Enter
No use.
15) CLEAR
Press key CLEAR, the Number input area will reset
16)
PRE―SET
I.
This is used to set up the Presets. Input the Preset No. in the Number
area, and press key PRE―SET to setup the PRESET. If succeed, the
number input area will reset automatically. PRESET NO. (1-32)
(34-66)
II.
Pressing this key for two seconds can delete the PRESET set up in
the speed dome or receiver. Input the Preset No. in the Number area,
and press key PRESET for seconds to delete the Preset. If succeed,
the number input area will reset automatically. PRESET NO. (1-32)
(34-66)
18) MUX-C
No use
Page 5
19) PGM
input 1-3, and then press key PGM to adjust the speed zoom
Input 50,and then press key PGM to select Protocol P.
Input 44,and then press key PGM to select Protocol D.
Input 12,and then press key PGM to select Baud Rate to1200.
Input 24,and then press key PGM to select Baud Rate to 2400.
Input 48,and then press key PGM to select Baud Rate to 4800.
Input 96,and then press key PGM to select Baud Rate to 9600.
If the above action can succeed, the number input area will reset
automatically
20) AUX1—AUX4
When the shift key is invalidation, AUX1 to AUX4 is slave control1-key
can alternative key. Open and shut.
When the shift key is validation, AUX1 is full-screen, AUX2 is four-screen,
AUX3 is nine-screen, AUX4 is sixteen-screen.
5.
KEY BOARD CONNECTION
Connect O/P with RS-485+ A
Connect Y/L with RS-485- B
Inner connection diagram
B
/
L
O
/
R
S
/
L
B
/
R
B
/
K
Y
/
L
R
/
D
G
/
R
NOTE: There is a film on the LCD. Take it off before using.
Page 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement