Advertisement
Advertisement
Portable LCD Projector
Models 8767A, 8771, 8070
User's Manual
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your Dukane Projector and keep the manual handy for future reference. Your serial number is located on the bottom of your projector.
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS
CAN BE FULLY INSERTED.
DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST
BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Acoustic Noise Information Ordinance-3. GSGV (for Germany only):
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
CAUTION
• Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will disappear.
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
i
Important Information
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling: a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes.
d. Please consult your dealer for more information.
ii
Important Information
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least 3 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately and have the object removed by a qualified Dukane service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause unpredictable outcome such as fire or injury to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to melting of the cap and possibly burning your hands due to the heat emitted from the light output.
7. The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply fits this requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
11. Do not handle the power plug with wet hands.
CAUTION
• Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated while the projector is turned on.
• Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.
• When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle to the projector cabinet are tight.
Insufficient tightening of the two screws could result in the projector falling and causing injury.
• Do not send the projector in the soft carrying case by parcel delivery service or cargo shipment. The projector inside the soft carrying case could be damaged.
• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[Advanced] → [Fan Mode] → [High].)
• Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
* While the Hour Glass icon appears.
* While the cooling fans are running. (The cooling fans continue to work for 30 seconds after the projector is turned off).
iii
Important Information
Lamp Replacement
• To replace the lamp, follow all instructions provided on page 53 .
• Be sure to replace the lamp when the message “The lamp has reached the end of its usable life. Please
replace the lamp.” appears. If you continue to use the lamp after the lamp has reached the end of its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your Dukane dealer for lamp replacement.
• Allow a minimum of 30 seconds to elapse after turning off the projector. Then turn off the main power switch, disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.
iv
Table of Contents
Important Information .........................................................................
i
1. Introduction ......................................................................................
1
� What's in the Box? ........................................................................................................ 1
� Introduction to the Projector ......................................................................................... 2
� Part Names of the Projector ......................................................................................... 4
Attaching the Supplied Carrying Handle ................................
................................ 5
Top Features ........................................................................................................... 6
Terminal Panel Features ......................................................................................... 7
� Part Names of the Remote Control .............................................................................. 8
8767A/8070 .......................................................................................................... 8
Battery Installation ........................................................................................... 10
Remote Control Precautions ............................................................................ 10
Operating Range for Wireless Remote Control ................................................ 10
8771 ............
.......................................................................................................... 11
Battery Installation ........................................................................................... 12
Remote Control Precautions ............................................................................ 12
Operating Range for Wireless Remote Control ................................................ 12
2. Installation and Connections ....................................................
13
� Setting Up the Screen and the Projector .................................................................... 13
Selecting a Location .............................................................................................. 13
Throw Distance and Screen Size .......................................................................... 15
� Making Connections ................................................................................................... 17
Enabling the computer’s external display .............................................................. 17
Connecting Your PC or Macintosh Computer ........................................................ 17
To connect SCART output (RGB) ......................................................................... 18
Connecting an External Monitor ........................................................................... 19
Connecting Your DVD Player with Component Output .......................................... 20
Connecting Your VCR or Laser Disc Player .......................................................... 21
Connecting the Supplied Power Cable ................................................................. 22
3. Projecting an Image (Basic Operation) .................................
23
� Turning on the Projector ............................................................................................. 23
Note on Startup Screen (Menu Language Select screen) .................................... 24
� Selecting a Source ..................................................................................................... 25
� Adjusting the Picture Size and Position ...................................................................... 27
� Correcting Keystone Distortion ................................................................................... 29
� Optimizing RGB Picture Automatically ....................................................................... 31
� Turning Up or Down Volume ....................................................................................... 31
� Turning off the Projector ............................................................................................. 32
� After Use..................................................................................................................... 32 v
Table of Contents
4. Convenient Features ....................................................................
33
� Turning Off the Image and Sound ............................................................................... 33
� Freezing a Picture ( 8767A/8070 only) ...
..................................................................... 33
� Enlarging and Moving a Picture ( 8767A/8070 only) .....
.............................................. 33
� Using the Remote Mouse Function ( 8767A/8070 only) ..
...
......................................... 34
5. Using On-Screen Menu ................................................................
35
� Using the Menus......................................................................................................... 35
� Menu Elements........................................................................................................... 37
� List of Menu Items ...................................................................................................... 38
� Menu Descriptions & Functions [Picture].................................................................... 40
� Menu Descriptions & Functions [Image] ..................................................................... 42
� Menu Descriptions & Functions [Setup] ..................................................................... 43
� Menu Descriptions & Functions [Advanced] ............................................................... 45
� Menu Descriptions & Functions [Information] ............................................................. 49
� Menu Descriptions & Functions [Default] ................................................................... 50
6. Maintenance ...................................................................................
51
� Cleaning or Replacing the Filter ................................................................................ 51
� Cleaning the Cabinet and the Lens ........................................................................... 52
� Replacing the Lamp................................................................................................... 53
7. Appendix ..........................................................................................
56
� Troubleshooting ......................................................................................................... 56
� Specifications ............................................................................................................ 59
� Cabinet Dimensions .................................................................................................. 61
� Pin Assignments of D-Sub COMPUTER Input Connector ........................................ 63
� Compatible Input Signal List ...................................................................................... 64
� PC Control Codes and Cable Connection ................................................................. 65
� Optional Presentation Remote Control Kit (PR52KIT)............................................... 67
� Troubleshooting Check List ........................................................................................ 71 vi
1. Introduction
� What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
Projector
R-2
PUTE
TER
MPU CO
ADJ.
VIDE
ATUS
LAM
WER
ON
SELECT
Power cable
CU
Soft carrying case
Lens cap
RGB signal cable
User's manual
Important Information
For 8767A and 8070 only
ENTER
UM
E
S-V
IDE
O
VID
EO
2
1
L-C
LICK
MO
USE
PUTE
R
AUTO
ADJ.
PIC
TUR
E
FRE
EZE
HEL
P
R-C
LIC
K
EXIT
OFF
MAG
NIF
Y
PIC
-MU
POW
ER
TE
UP E
ON
Remote control
(7N900521)
Batteries (AAA ⳯2)
For 8771 only
ASPECT
SOURCE
PO
WER
PIC-M
UTE
SELECT
Remote control
(7N900551)
CR
20
25
Lithium battery (CR2032)
Remote mouse receiver
(7N900561)
Carrying handle (24F39671)
Screw (M4
⳯2: 24N07501)
Flathead screwdriver (24H51611)
1
1. Introduction
� Introduction to the Projector
This section introduces you to your new Dukane Projector and describes the features and con trols.
Congratulations on Your Purchase of The Dukane Projector
The 8767A/8070/8771 is one of the very best projectors available today. The this projector enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen, and the projector can be permanently mounted on a ceiling* 1 . The remote control can be used wirelessly.
* 1 Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
• Auto vertical keystone correction up to +/– 30 degrees
• Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white screen material.
• Quick Start & Quick Shutoff
The quick start & quick shutoff function means you can set up or put away the projector without delay.
Nine seconds after turning on the power, the projector is ready to display PC or video images.
When you're finished, the fans stop in 30 seconds after turning off the power, so you can put away the projector quickly after the conference or class.
• Low level operation noise
• Short focal length lens
• 130W lamp (110W Eco mode) : 8771
180W lamp (150W Eco mode) : 8767A/8070
• Direct keys for source selection
• New Color Management system
• New menu design improves operation
• Safety protect by Security function
Security feature prevents the projector from being used by unauthorized individuals.
Keyword prevents unauthorized individuals from changing projector settings or adjustments.
• E xclusive Advanced intelligent pixel blending technology - an extremely accurate image compression technology - offers a crisp image with UXGA (1600 ⳯1200) resolution*
2 .
• Supports most IBM VGA, SVGA, XGA , SXGA/UXGA, Macintosh, component signal
(YCbCr/ YPbPr) or any other RGB signals within a horizontal frequency range of 24 to 100 kHz and a vertical frequency range of 50 to 120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and
NTSC4.43 standard video signals.
* 2 A UXGA (1600 ⳯1200) and SXGA image (1280⳯1024) are on 8767A and 8771.
A UXGA (1600 ⳯1200), SXGA (1280⳯1024) and XGA (1024⳯768) image are displayed on 8070.
2
1. Introduction
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
• You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse wireless from across the room. The remote mouse receiver supports almost any PC using a USB connection
( 8767A AND 8070 ).
• You can control the projector with a PC or control system using the PC Control port.
• The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or auditorium.
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find an overview. If the section doesn't apply, you can skip it.
• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.
• Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of Microsoft Corporation.
• Other product and company names mentioned in this user’s manual may be the trademarks or registered trademarks of their respective holders.
3
1. Introduction
� Part Names of the Projector
Front/Top
Zoom Lever
(See page 28 )
OM
ZO
CU
Controls
(See page 6 )
Ventilation (inlet) / Filter Cover
(See page 51 )
LE
SE
Focus Ring
(See page 28 )
Remote sensor
(See page 10 for 8767A/8070 )
(See page 12 for 8771 )
CU
ZOOM
Built-in Security Slot ( )*
Ventilation (inlet)
Lens
Adjustable Tilt Foot Lever
(See page 27 )
Lens Cap
Adjustable Tilt Foot
(See page 27 )
* This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Rear
FOCU
S
ZOOM
Monaural Speaker
(1W)
Terminal Panel
(See page 7 )
SELECT
ON/STAND BY
LAM
STATUS P
PO
WER
VIDEO
S-VIDEO
COMPUTER-1
COM
PUTER-2
AUTO
ADJ.
VIDEO IN
S-VIDEO IN
L/MONO
AUDIO
R
L/MONO
AUDIO
R
AUDIO
AUDIO OUT
COMPUTER 1 IN
COMPUTER OUT
AUDIO
PC CONTROL
COMPUTER 2 IN
Remote sensor
(See page 10 for 8767A/8070 )
(See page 12 for 8771 )
AC IN
Ventilation (outlet)
Heated air is exhausted from here.
AC Input
Connect the supplied power cable's two-pin plug here, and plug the other end into an active wall outlet. (See page 22 )
Main Power Switch
When you plug the supplied power cable into an active wall outlet and turn on the Main Power, the POWER indicator turns orange and the projector is in standby mode.
(See page 23 )
4
Bottom
Adjustable Tilt Foot
(See page 27 )
Adjustable Tilt Foot Lever
(See page 27 )
Lamp Cover
(See page 53 )
1. Introduction
Adjustable Tilt Foot Lever
(See page 27 )
For 8767A and 8070 only
Attaching the supplied carrying handle
You can carry the projector by attaching the supplied carrying handle securely to the projector.
To attach the supplied carrying handle, use the supplied flathead screwdriver and two screws.
Place a soft cloth on the working surface before turning the projector over to prevent scratching the top cover.
Make sure that the carrying handle is attached with correct orientation as shown below.
Flathead screwdriver
Screw
Carrying handle
CAUTION
When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle to the projector cabinet are tight.
5
1. Introduction
Top Features
11 10 2 3 4
LAMP
STATUS
POWER
9
VIDEO
SELECT
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
AUTO
ADJ.
12 13 1 5 6 7 8
7. COMPUTER1 and 2 Buttons 1. POWER Button (ON / STAND BY) ( )
Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode.
To turn on the projector, press and hold this button for a minimum of two seconds. To turn off the projector, press this button twice.
Press this button to select an RGB source from computer or component equipment connected to your
COMPUTER 1 or 2 port.
8. AUTO ADJ. Button
Use this button to adjust an RGB source for an optimal picture (See page 31 ).
2. POWER Indicator
When this indicator is green, the projector is on; when this indicator is orange, it is in standby mode. See the
Power Indicator section on page 56 for more details.
9. Source Indicators
When one of the COMPUTER, VIDEO or S-VIDEO input is selected, the corresponding source indicator lights.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred, the lamp cover is not attached properly or the projector has overheated. If this light remains orange, it indicates that you have pressed a cabinet key while the Cabinet Button Lock is enabled. See the
Status Indicator section on page 56 for more details.
10. MENU Button
Displays the menu.
4. LAMP Indicator
If this light blinks red rapidly, it's warning you that the lamp has reached the end of its usable life. After this light appears, replace the lamp as soon as possible
(See page 53 ). If this is lit green continually, it indicates that the lamp mode is set to Eco. See the Lamp
Indicator section on page 56 for more details.
11. SELECT 왖왔왗왘 / Volume Buttons
왖왔 : Use these buttons to select the menu of the item you wish to adjust.
왗왘 : Use these buttons to change the level of a selected menu item. A press of the 왘 button executes the selection. When no menus appear, these buttons work as a volume control.
When an image is magnified, the SELECT 왖왔왗왘 button moves the image.
5. VIDEO Button
Press this button to select a video source from a VCR,
DVD player, laser disc player or document camera.
12. ENTER Button
Executes your menu selection and activates items selected from the menu.
6. S-VIDEO Button
Press this button to select an S-Video source from a
VCR, DVD player, laser disc player or document camera.
13. EXIT Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button will close the menu.
6
1. Introduction
Terminal Panel Features
4
VIDEO IN
L/MONO AUDIO R
COMPUTER 1 IN
1
AUDIO
S-VIDEO IN
L/MONO
AUDIO
R
AUDIO OUT
MONITOR OUT
PC CONTROL
COMPUTER 2 IN
3 2 5
1. COMPUTER 1 and 2 IN / Component Input Connector
(Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM compatible or Macintosh computers. Use the supplied RGB cable to connect to your computer. This also serves as a component input connector that allows you to connect a component video output of component equipment such as a DVD player.
This connector also supports SCART output signal.
See page 18 for more details.
COMPUTER AUDIO Input Mini Jack (Stereo Mini)
This is where you connect the audio output from your computer or DVD player when connected to the COM-
PUTER input. A commercially available audio cable is required.
For example, when a cable mini-plug is inserted into the left AUDIO IN jack only, only left sound is output.
3. S-VIDEO IN Connector (Mini DIN 4 Pin)
Here is where you connect the S-Video input from an external source like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than the traditional composite video format.
S-VIDEO AUDIO Input Jacks L/R (RCA)
These are your left and right channel audio inputs for stereo sound from an S-Video source.
2. MONITOR OUT Connector (Mini D-Sub 15 Pin)
You can use this connector to loop your computer image to an external monitor from the RGB input source.
This connector outputs RGB signal in standby mode.
AUDIO OUT Mini Jack (Stereo Mini)
4. VIDEO IN Connector (RCA)
Connect a VCR, DVD player, laser disc player, or document camera here to project video.
VIDEO AUDIO Input Jacks L/R (RCA)
These are your left and right channel audio inputs for stereo sound from a Video source.
You can use this jack to output sound from the currently selected source (COMPUTER, VIDEO or S-
VIDEO). Output sound level can be adjusted in accordance with the sound level of the internal speaker.
Note that this cannot be used as a headphone jack.
(When audio equipment is connected, the projector speaker is disabled.)
When a cable mini-plug is inserted into this jack, both the right and left audio signals are not mixed, but separate.
5. PC CONTROL Port (DIN 8 Pin)
Use this port to connect a PC or control system. This enables you to control the projector using serial communication protocol. If you are writing your own program, typical PC control codes are on page 65 .
7
� Part Names of the Remote Control
For 8767A/8070
OFF ON
1 5. PIC-MUTE Button
This button turns off the image and sound for a short period of time. Press again to restore the image and sound.
3
POWER
2
4
7
MAGNIFY PIC-MUTE
MENU
PAGE
UP
DOWN
6
5
8
6. PAGE UP/DOWN Button
Use these buttons to operate your computer with the supplied remote mouse receiver. See page 34 . You can use these buttons to scroll the viewing area of the window or to move to the previous or next slide in
PowerPoint on your computer.
9
ENTER EXIT
10
7. MENU Button
Displays the menu for various settings and adjustments.
11
13
14
17
L-CLICK R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
1
S-VIDEO
2
VOLUME ASPECT HELP
PICTURE FREEZE
12
16
15
18
20
21
19
1. Introduction
8. SELECT 왖왔왗왘 (Mouse) Button
왖왔 : Use these buttons to select the menu of the item you wish to adjust.
왗왘 : Use these buttons to change the level of a selected menu item. A press of the 왘 button executes the selection.
When an image is magnified, the SELECT 왖왔왗왘 button moves the image. See page 33 .
9. ENTER Button
Use this button to enter your menu selection. It works the same way as the ENTER button on the cabinet.
See page 6 .
NOTE: If you are using a Macintosh computer, you can click either the MOUSE R-CLICK or MOUSE L-CLICK button to activate the mouse.
10. EXIT Button
It works the same way as the EXIT button on the cabinet. See page 6 .
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector cabinet.
11. MOUSE L-CLICK Button
This button works as the mouse left button when the supplied remote mouse receiver is connected with your computer. See page 34 .
2. POWER ON Button
When the main power is on, you can use this button to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER
ON button for a minimum of two seconds.
12. MOUSE R-CLICK Button
This button works as the mouse right button when the supplied remote mouse receiver is connected with your computer. See page 34 .
3. POWER OFF Button
You can use this button to turn your projector off.
13. VIDEO Button
Press this button to select a video source from a VCR,
DVD player, laser disc player or document camera.
NOTE: To turn off the projector, press the POWER OFF button twice.
14. S-VIDEO Button
Press this button to select an S-Video source from a
VCR.
4. MAGNIFY (+)(–) Button
Use this button to adjust the image size up to 400%.
The image is magnified about the center of the screen.
See page 33 .
15. COMPUTER 1/2 Button
Press this button to select COMPUTER 1 or 2 (or Component) input.
8
3
4
7
9
11
13
14
17
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
L-CLICK R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
1
S-VIDEO
VOLUME
2
ASPECT HELP
PICTURE FREEZE
16. AUTO ADJ. Button
Use this button to adjust an RGB source for an optimal picture.
See page 31 .
17. VOLUME (+)(–) Button
Press (+) to increase the volume and (–) to decrease it.
18. ASPECT Button
Press this button once to display the Aspect Ratio select menu. Keep pressing will change aspect ratios.
See page 42 .
19. PICTURE Button
Press this button to display the Picture adjustement menu to adjust Wall Color, Picture Management,
Brightness, Contrast, Sharpness, Color and Hue. See pages 40 to 41 .
20. HELP Button
Provides the information on the current signal and projector settings. See page 49 .
21. FREEZE Button
This button will freeze a picture. Press again to resume motion. See page 33 .
9
1
2
6
5
8
10
12
16
15
18
20
21
19
1. Introduction
1. Introduction
Battery Installation
1
Press firmly and slide the battery cover off.
2
Remove both old batteries and install new ones (AAA). Ensure that you have the batteries' polarity (+/–) aligned correctly.
3
Slip the cover back over the batteries until it snaps into place. Do not mix different types of batteries or new and old batteries.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of batteries together.
Operating Range for Wireless Remote Control
7m/22 feet
Remote sensor on projector cabinet
30
°
30 °
30
°
30 °
7m/22 feet
Remote control
• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
10
1. Introduction
For 8771
1
2
3
4
6
8
SELECT
SOURCE PIC-MUTE
ASPECT POWER
5
7
9
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector cabinet.
2. MENU Button
Displays the menu for various settings and adjustments.
3. SELECT 왖왔왗왘 / Volume Buttons
왖왔 : Use these buttons to select the menu of the item you wish to adjust.
왗왘 : Use these buttons to change the level of a selected menu item. A press of the 왘 button executes the selection. When no menus appear, these buttons work as a volume control.
4. ENTER Button
Executes your menu selection and activates items selected from the menu.
5. EXIT Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button will close the menu.
6. SOURCE Button
Press this button to select a video source such as a
PC, VCR or DVD player. Each time this button is pressed, the input source will change as follows:
8771
Computer1
→ Computer2 → Video → S-Video →
Computer1 → ...
7. PIC-MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
8. ASPECT Button
Press this button once to display the Aspect Ratio select menu. Keep pressing will change aspect ratios.
See page 42 .
9. POWER Button
Use this button to turn the power on and off when the main power is supplied and the projector is in standby mode.
To turn on the projector, press and hold this button for a minimum of two seconds. To turn off the projector, press this button once to display the confirmation message and then press the POWER button or EN-
TER button.
11
1. Introduction
Battery Installation
1
Push the catch to the right and remove the battery holder.
2
Remove the old Lithium coin cell and install new one (CR2032).
Ensure that the side with the mark “+” is up.
CR2025
3
Push the battery holder back into the remote control until you feel a click.
CR2025
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the battery.
• Do not place the battery upside down.
• Keep the coin cell battery out of reach of children so as not to allow them to swallow the cell battery.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
Remote sensor on projector cabinet
7m/22 feet
30 °
30 ° 30 °
30 °
7m/22 feet
Remote control
• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
Weak battery will also prevent the remote control from properly operating the projector.
12
2. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
To the wall outlet.
2
3
1
Your projector is simple to set up and use.
But before you get started, you must first: z Set up a screen and the projector.
x Connect your computer or video equipment to the projector. See pages 17 to
21 .
c Connect the supplied power cable. See page 22 .
NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. When moving the projector or when it is not in use, cover the lens with the lens cap.
� Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 21" (0.53 m) measured diagonally when the projector is roughly 29 inches (0.73 m) from the wall or screen. The largest the image can be is 300" (7.6 m) when the projector is about 393 inches (10 m) from the wall or screen. Use the drawing below as a guide.
Screen Size (Unit: cm/inch
609.6(W) ⳯457.2(H) / 240(W)⳯180(H)
300" Screen Size
487.7(W)
⳯365.8(H) / 192(W)⳯144(H)
406.4(W)
⳯304.8(H) / 160(W)⳯120(H)
365.8(W) ⳯274.3(H) / 144(W)⳯108(H)
200
"
180"
304.8(W)
⳯228.6(H) / 120(W)⳯90(H)
150"
243.8(W)
⳯182.9(H) / 96(W)⳯72(H)
30"
21"
40"
120"
203.2(W)
⳯152.4(H) / 80(W)⳯60(H)
162.6(W)
⳯121.9(H) / 64(W)⳯48(H)
121.9(W) ⳯91.4(H) / 48(W)⳯36(H)
81.3(W) ⳯61.0(H) / 32(W)⳯24(H)
61.0(W)
⳯45.7(H) / 24(W)⳯18(H)
42.7(W) ⳯32(H) / 17(W)⳯13(H)
Lens center
60"
100"
80"
0.7/29
1.0/38
1.3/51 2.0/78 2.6/104 3.3/130
240
"
4.0/157
5.0/196
6.0/236 6.6/262
8.0/314
Distance (Unit: m/inch)
10.0/393
13
14
2. Installation and Connections
2. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.
Distance Chart
Screen Width
Screen Diagonal
Screen center
Screen Height
(B)
(D)
Lens Center
Throw Angle ( 움)
Screen Bottom
Throw Distance (C)
B = Vertical distance between lens center and screen center
C = Throw distance
D = Vertical distance between lens center and bottom of screen (top of screen for ceiling application)
α = Throw angle
NOTE: Distances may vary +/-5%.
AC IN
90
100
120
150
180
200
210
240
270
Diagonal inch
21
25
30
40
60
72
80
84
300
Screen Size
Width inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240
108
120
126
144
162
54
60
72
90
180
Height inch
13
15
18
24
36
43
48
50
B inch
5
6
7
10
14
17
19
20
22
24
50
57
65
72
29
36
43
48
C
Wide – Tele inch
–– –
28 –
29
34
34 –
46 –
42
56
70 – 85
84 – 102
93 – 113
98 – 119
105 – 128
117 – 142
141 – 171
176 – 214
212 – 257
236 – 285
247 – 300
283 – 343
319 – 386
354 – 429
D
-7
-9
-11
-12
-13
-5
-5
-6
-6 inch
-1
-2
-2
-2
-4
-4
-15
-17
-18
α
Wide – Tele degree
–– – 9.9
12.0 – 9.8
11.9 – 9.8
11.7 – 9.7
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.5 – 9.6
11.5 – 9.6
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.4 – 9.5
11.4 – 9.5
Diagonal mm
533
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
Screen Size
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
Width mm
427
508
610
813
1219
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
Height mm
320
381
457
610
914
1097
1219
1280
B
440
490
510
550
610
730
910
1090
1210 mm
130
150
180
240
360
1270
1460
1640
1820
C
Wide – Tele mm
––– – 730
720 – 870
870 – 1060
1170 – 1420
1770 – 2150
2130 – 2590
2370 – 2880
2490 – 3020
2670 – 3240
2970 – 3600
3580 – 4330
4480 – 5420
5380 – 6520
5980 – 7240
6280 – 7610
7190 – 8700
8090 – 9790
8990 – 10880
D mm
-30
-40
-50
-60
-90
-110
-120
-130
-140
-160
-190
-230
-280
-310
-330
-370
-420
-470
α
Wide – Tele degree
–– – 9.9
12.0 – 9.8
11.9 – 9.8
11.7 – 9.7
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.5 – 9.6
11.5 – 9.6
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.4 – 9.5
11.4 – 9.5
15
WARNING
* Installing your projector on the ceiling must be done by a qualified technician. Contact your AV dealer for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.
• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 95˚F (35˚C).
• Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
2. Installation and Connections
• Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the vents on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projector's image enables you to enjoy a much larger image. Contact your dealer if you need a mirror system. If you're using a mirror system and your image is inverted, use the MENU and SELECT buttons on your projector cabinet or your remote control to correct the orientation. See page 44 .
16
2. Installation and Connections
� Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.
Connecting Your PC or Macintosh Computer
NOTE: The COMPUTER 1 connector supports Plug & Play (DDC2).
COMPUTER 1 IN COMPUTER 2 IN
VIDEO IN
L/MONO
AUDIO
R
COMPUTER 1 IN AUDIO
S-VIDEO IN
L/MONO
AUDIO
R
AUDIO OUT
MONITOR OUT
PC CONTROL
COMPUTER 2 IN
AUDIO
AC IN
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended that you use a commercially available distribution amplifier if connecting a signal cable longer than the supplied one.
Audio cable
(not supplied)
PHONE
PHONE
NOTE: For older Macintosh, use a commercially available pin adapter
(not supplied) to connect to your
Mac's video port.
IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)
IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cable. See page 22 .
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector.
17
2. Installation and Connections
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on the projector cabinet.
To connect SCART output (RGB) (Europe Operation)
Video equipment such as DVD player
COMPUTER 1 IN
VIDEO IN
L/MONO AUDIO R
COMPUTER 1 IN AUDIO
S-VIDEO IN
L/MONO
AUDIO
R
AUDIO OUT
MONITOR OUT
PC CONTROL
COMPUTER 2 IN
Projector
Female
AC IN
To COMPUTER 1 input
(COMPUTER input on VT47)
ADP-SC1
Commercially available SCART cable
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are required for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of your projector and a SCART output (RGB) of your video equipment.
3. Connect the supplied power cable. See page 22 .
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER 1 button on the remote control to select the COMPUTER 1 input.
Use the COMPUTER button on the remote control to select the COMPUTER input on VT47.
6. Press the MENU button on the remote control to display the menu.
7. From the menu, select [Advanced] → [Signal Select] → [Computer 1 ([Computer] on VT47)] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as
Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your dealer in Europe. Contact your dealer in Europe for more information.
18
2. Installation and Connections
Connecting an External Monitor
L/MONO AUDIO R
VIDEO IN MONITOR OUT
AUDIO OUT S-VIDEO IN
L/MONO
AUDIO
R
COMPUTER 1 IN
MONITOR OUT
AUDIO COMPUTER 2 IN AUDIO
PC CONTROL
MONITOR OUT
AC IN
RGB signal cable (supplied)
RGB signal cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog image you're projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.
3. Connect the supplied power cable. See page 22 .
4. Turn on the projector, monitor and the computer.
NOTE: Daisy chain connection is not possible.
19
Connecting Your DVD Player with Component Output
2. Installation and Connections
COMPUTER 1 IN AUDIO
VIDEO IN
L/MONO AUDIO R
COMPUTER 1 IN AUDIO
S-VIDEO IN
L/MONO
AUDIO
R
AUDIO OUT
MONITOR OUT
PC CONTROL
COMPUTER 2 IN
AC IN
Optional 15p - to - RCA (female)
⳯3 cable (ADP-CV1)
Component video RCA
⳯3 cable (not supplied)
Y C r L R
Component AUDIO OUT
DVD player
Audio Equipment
AUDIO IN
L R
Audio cable (not supplied)
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable
(RCA
⳯3) and the optional 15-pin-to-RCA (female)⳯3 cable to connect your DVD player to the COMPUTER IN connector on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a composite VIDEO output of the DVD player to the Video Input of the projector.
3. Connect the supplied power cable. See page 22 .
4. Turn on the projector and DVD player.
A component signal will be automatically displayed. If not, from the menu, select [Advanced] → [Signal Select] →
[Computer], and then place a check mark in the Component radio button.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
20
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
VIDEO IN AUDIO
COMPUTER 1 IN AUDIO COMPUTER 2 IN VIDEO IN
L/MONO
AUDIO
R
S-VIDEO IN
L/MONO
AUDIO
R
AUDIO OUT
MONITOR OUT
PC CONTROL
S-VIDEO IN AUDIO
AC IN
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
L R
AUDIO OUT
VIDEO S-VIDEO
VIDEO OUT
Audio equipment
AUDIO IN
L R
Audio cable (not supplied)
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect the audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your
VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on the projector.
Be careful to keep the right and left channel connections correct for stereo sound.
3. Connect the supplied power cable. See page 22 .
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via a scan converter.
21
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of the supplied power cable in the wall outlet.
FOCU
S
ZOOM
SE
LECT
ON
/ST
AND
BY
PO
R
LAM
P
STA
TUS
VID
EO
IDE
O
CO
MPU
TE
R-1
CO
MPU
TER
-2
VIDEO IN
S-VIDEO IN
L/M
ON
O AUDIO
R
L/M
ON
O
AUDIO
R
AUDIO
AUDIO OUT
COMPUTER 1 IN
COMPUTER OUT
AUDIO
PC CONTROL
COMPUTER 2 IN
AC IN
To wall outlet
←
Make sure that the prongs are fully inserted into both the AC IN and the wall outlet.
CAUTION:
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the cooling fans are running. The cooling fans continue to work for 30 seconds after the projector is turned off.
22
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
� Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button.
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off ( 䡬) position. Failure to do so may cause damage to the projector.
1. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).
• The POWER indicator will light orange.
See the Power Indicator section on page 56 for more details.
FO
CU S
ZO
OM
LAMP
STATUS
POWER
IN
AC
2. Press the POWER (ON/STAND BY) button on the projector cabinet or the POWER button on the remote control for a minimum of 2 seconds. The POWER indicator will turn to green and the projector will become ready to use.
After you turn on your projector, ensure that the computer or video source is turned on and that your lens cap is removed.
NOTE: When no signal is available, a blue, black or logo screen is displayed.
When the projector displays a blue or a black screen (not logo), the Eco mode will be automatically selected in "Lamp Mode."
NOTE: If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans runs without displaying an image for some time and then the projector will display the image.
SELECT
8767A8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
LAMP
STATUS
POWER VIDEO S-VIDEO
ON/STAND BY
8771
SOURCE PIC-MUTE
ASPECT POWER
Standby
LAMP
STATUS
POWER
Steady orange light
Blinking
LAMP
STATUS
POWER
Power On
LAMP
STATUS
POWER
Blinking green light
Steady green light
See page 56 for more details.
23
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT 왖 or 왔 button to select one of the 8 languages for the menu.
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
SELECT
ON/STAND BY
AUTO
ADJ.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu operation.
If you want, you can select the menu language later. See "Language" on pages 38 and 44 .
SELECT
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
AUTO
ADJ.
8771
SELECT
SOURCE PIC-MUTE
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
When the Lamp mode is set to Eco, the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and then turn on the power.
24
3. Projecting an Image (Basic Operation)
� Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or VCR connected to the projector.
Using the cabinet buttons
Press any one of the COMPUTER 1/2
VIDEO and S-VIDEO buttons.
The corresponding indicator will light green.
Using the Remote Control (8767A/8070)
Press any one of the COMPUTER 1/2, COMPONENT, VIDEO or S-
VIDEO buttons.
SELECT
8767A/8070
L-CLICK R-CLICK
VIDEO
MOUSE
COMPUTER AUTO ADJ.
1
S-VIDEO
2
VOLUME ASPECT HELP
PICTURE FREEZE
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
AUTO
ADJ.
8771
Selecting from the Source List (8771)
1. Press and quickly release the SOURCE button on the remote control.
The Source list will be displayed.
SOURCE PIC-MUTE
ASPECT POWER
2. Press and quickly release the SOURCE button to select the source in the Source list.
Each time the SOURCE button is pressed, the selection in the
Source list will change as follows:
8771
Computer 1 → Computer 2 → Video → S-Video → Computer 1 → ...
8771
8771
3. Press the ENTER button to display the selected source.
NOTE: Highlighting the source for 2 seconds without pressing the ENTER button will also display the selected source.
SOURCE PIC-MUTE
ASPECT POWER
25
3. Projecting an Image (Basic Operation)
Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 1 second, the projector will search for the next available input source. Each time you press and hold the SOURCE button for a minimum of 1 second, the source will change as follows:
SOURCE
8771
PIC-MUTE
8771
Computer 1 → Computer 2 → Video → S-Video → Computer 1 → ...
ASPECT POWER
If no input signal is present, the input will be skipped.
26
3. Projecting an Image (Basic Operation)
� Adjusting the Picture Size and Position
Place your projector on a flat level surface and ensure that the projector is square to the screen.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See page 29 .
ZOO
FOCU
AC
IN
Move the projector left to center the image horizontally on the screen.
AC I
ZOOM
FOC US
Adjust the Tilt Foot
1. Lift the front edge of the projector.
2. Push up the Adjustable Tilt Foot Levers on the right and left sides of the projector to extend the adjustable tilt feet (maximum height).
2
1
AUTO
Adjustable Tilt
Foot Lever
Adjustable Tilt Foot
2
Adjustable Tilt
Foot Lever
3. Push down the Adjustable Tilt Foot Levers.
4. Lower the front of the projector to the desired height and release the Adjustable Tilt Foot Lever to lock the Adjustable tilt foot. There is approximately 10 degrees of up and down adjustment for the front of the projector.
CAUTION
Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.
4
3
ZOOM
COMPUTER-2
COMPUTER-1
S-VIDEO
VIDEO
STATUS
LAMP
WER
ON/STAND BY
SELECT
4
27
Zoom
Use the ZOOM lever to finely adjust the image size on the screen.
3. Projecting an Image (Basic Operation)
8767A/8070/8771
FOC
US
ZOO
M
NOTE: Digital Zoom can cause result in a blurry image because zooming is made electronically.
Focus
Use the FOCUS ring to obtain the best focus.
AC IN
ZOOM
FOC
US
FOC
US
AC
IN
ZOOM
FOC US
28
3. Projecting an Image (Basic Operation)
� Correcting Keystone Distortion
Auto Keystone Correction
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special operation required. Just put the projector on a flat surface.
Note that the vertical keystone angle can be corrected between 30 degrees upward and 30 degrees downward of projector tilt from level.
NOTE: Auto and Manual Keystone correction angle could be less than 30 degrees depending on some kinds of signal and aspect ratios.
NOTE: The Auto Keystone Correction feature can cause an image to be slightly blurred because the correction is made electronically.
Manual Keystone Correction
You can also correct the vertical keystone distortion manually.
To do so:
1. Press the MENU button.
The menu will be displayed.
2. Turn off the Auto Keystone function.
Use the SELECT 왔 button to select
“Image” and then press the SELECT 왘 button. The “Auto Keystone” will be displayed. Press the SELECT 왘 to select
“Off”.
3. Select the Keystone function.
Use the SELECT 왔 button to select
“Keystone”.
4. Correct the vertical distortion.
Use the SELECT 왗 or 왘 button to correct the vertical keystone distortion.
NOTE: The Keystone Correction feature can cause an image to be slightly blurred because the correction is made electronically.
29
5. Press the MENU button to close the menu.
3. Projecting an Image (Basic Operation)
NOTE: You can save the changes using the Keystone Save feature when you turn off the projector. See page 42 .
30
3. Projecting an Image (Basic Operation)
� Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
AUTO
ADJ.
[Normal picture]
8767A/8070
L-CLICK R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
1
S-VIDEO
2
VOLUME ASPECT HELP
PICTURE FREEZE
8771
SELECT
SOURCE PIC-MUTE
Press the Auto Adjust button to fine-tune the computer image or to remove any vertical banding that might appear and to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmering). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering.)
This adjustment may be necessary when you connect your computer for the first time.
NOTE:
Some signals may not be displayed correctly or take time.
• The Auto Adjust function does not work for component and video signal.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Horizontal/Vertical Position Clock and Phase manually. See page 48 .
� Turning Up or Down Volume
8767A/8070
Increase volume
L-CLICK R-CLICK
MOUSE
VIDEO COMPUTER AUTO ADJ.
1
S-VIDEO
2
VOLUME ASPECT HELP
PICTURE FREEZE
Decrease volume
Sound level from the speaker and the AU-
DIO OUT jack (Stereo mini) on the projector can be adjusted.
8771
SELECT
Decrease volume Increase volume
31
� Turning off the Projector
To turn off the projector:
First, press the POWER (ON/STAND BY) button on the projector cabinet or the POWER OFF button on the remote control. The “Power Off / Are you sure?” message will appear.
3. Projecting an Image (Basic Operation)
SELECT
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
AUTO
ADJ.
Secondly, press the ENTER button or press the POWER
(ON/STAND BY), the POWER OFF or the POWER button again.
The power indicator will glow orange. After the projector turns off, the cooling fans keep operating for 30 seconds
(Cooling-off time).
Immediately after turning on the projector and displaying an image, you cannot turn off the projector for 60 seconds.
Finally, turn off the Main Power switch. The power indicator will go out.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER
L-CLICK
EXIT
R-CLICK
8771
SELECT
SOURCE PIC-MUTE
ASPECT POWER
Power On
LAMP
STATUS
POWER
Steady green light
Fan running
LAMP
STATUS
POWER
Blinking orange light
Standby
LAMP
STATUS
POWER
Steady orange light
CAUTION
Do not unplug the power cable from the wall outlet or do not turn off the main power under any one of the following circumstances. Doing so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the cooling fans are running. (The cooling fans continue to work for 30 seconds after the projector is turned off).
FO CU
S
ZO OM
AC
IN
� After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
5. Put the projector and its accessories in the supplied soft carrying case.
32
4. Convenient Features
쐃 Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
쐇 Freezing a Picture
(8767A/8070 only)
Press the FREEZE button to freeze a picture. Press again to resume motion.
NOTE: The optional remote control PR52 (RD-408E) allows you to use this feature on 8771.
8767A/8070
1
S-VIDEO
VOLUME
2
ASPECT HELP
PICTURE FREEZE
� Enlarging and Moving a Picture
(8767A/8070 only)
You can enlarge the picture up to 400 percent.
To do so: 8767A/8070
1. Press the MAGNIFY (+) button to magnify the picture.
To move the magnified image, use the SELECT button.
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
2. Return the image to the original size.
NOTE: The optional remote control PR52 (RD-408E) allows you to use this feature on 8771.
33
SELECT
LAMP
STATUS
POWER VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
AUTO
ADJ.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
4. Convenient Features
� Using Remote Mouse Receiver
(8767A/8070)
The remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a great convenience for clicking through your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change your computer settings.
Computer
Remote mouse receiver
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver
7m/22 feet
30˚
30˚
Remote sensor on the remote mouse receiver
When connecting using the USB terminal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP* or Windows 2000 operating system.
* NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
Operating your computer’s mouse from the remote control
You can operate your computer's mouse from the remote control.
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer.
왖왔왗왘 / Mouse Buttons: moves the mouse cursor on your computer.
MOUSE L-CLICK Button: works as the mouse left button.
MOUSE R-CLICK Button: works as the mouse right button.
34
5. Using On-Screen Menu
� Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or projector cabinet to display the Menu.
8771 8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
SELECT
SOURCE PIC-MUTE
2. Press the SELECT 왖왔 buttons on the remote control or the projector cabinet to highlight the menu for the item you want to adjust or set.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
3. Press the SELECT 왘 button or the ENTER button on the remote control or the projector cabinet to select a submenu or item.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
35
5. Using On-Screen Menu
4. Use the SELECT 왖왔 buttons on the remote control or the projector cabinet to select the item you want to adjust or set.
8767A/8070 8771
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
SELECT
SOURCE PIC-MUTE ENTER EXIT
5. Adjust the level or turn the selected item on or off by using
SELECT 왗 or 왘 buttons on the remote control or the projector cabinet.
The on-screen slide bar will show you the amount of increase or decrease.
Changes are stored until you adjust it again.
EXIT ...................... Return to the previous menu.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
6. Repeat steps 2-5 to adjust an additional item, or press the
MENU button to close the menu.
8767A/8070
OFF
POWER
MAGNIFY PIC-MUTE
ON
PAGE
UP
DOWN
MENU
ENTER EXIT
8771
SELECT
SOURCE PIC-MUTE
36
쐇 Menu Elements
Highlight
Title
5. Using On-Screen Menu
Slide bar
Source Off Timer remaining time
Radio button
Solid triangle
Check mark
Tab
Thermometer symbol
Key symbol
Menu windows or dialog boxes typically have the following elements:
Title .......................................... Indicates the menu title.
Highlight ................................... Indicates the selected menu or item.
Source ...................................... Indicates the currently selected source.
Remaining countdown time ..... Indicates the remaining countdown time when the Off Timer is preset.
Solid triangle ............................ Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab ........................................... Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ............................ Use this round button to select an option in a dialog box.
Check mark .............................. Indicates the item is selected.
Slide bar ................................... Indicates settings or the direction of adjustment.
Key symbol .............................. Indicates the Cabinet Button Lock is enabled.
Thermometer symbol ............... Indicates the lamp mode is forcibly set to Eco mode because the internal temperature is too high.
37
5. Using On-Screen Menu
쐋 List of Menu Items
Picture
Wall Color Off, Blackboard, Light yellow, Light green, Light blue, Sky blue, Light rose, Pink
Picture Management Presentation, Video, Movie, Graphic, sRGB
User
Base Setting Presentation, Video, Movie, Graphic, sRGB
Gamma Correction Dynamic, Black Detail, Natural
Brightness R,G,B
Contrast R,G,B
Brightness
Contrast
Sharpness
Color
Hue
Image
Auto Keystone
Keystone
Keystone Save
Aspect Ratio
Cinema Position
Setup
Off Timer
Lamp Mode
Language
On, Off
On, Off
Normal, Wide Zoom, Cinema, Native
Menu Color Select
Menu Display Time
Background
Orientation
Beep
Off, 0:30, 1:00, 2:00, 3:00, 4:00, 6:00, 8:00
Normal, Eco
Language-1 English, Deutsch, Français, Italiano, Español, Português, Nederlands
Language-2 Svenska, Norsk, Suomi, Cesky , Magyar, Polski, Türkçe
Language-3 , , , , , , Dansk
Color, Monochrome
Manual, Auto 5 sec, Auto 15sec, Auto 45 sec
Blue, Black, Logo
Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front
On, Off
Advanced
Security
Cabinet Button
Page2
Video
S-Video
On, Off
Lock, Unlock
Fan Mode High, Auto
Signal Select COMPUTER1* RGB/Component, RGB, Component, Scart
COMPUTER2 RGB/Component, RGB, Component
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Power Management On, Off
Noise Reduction On, Off
Flicker Reduction On, Off
Auto Adjust
Horizontal
Vertical
Clock
Off, Normal, Fine
Phase
Communication Speed 4800, 9600, 19200
38
5. Using On-Screen Menu
Information
Page1
Page2
Remaining Lamp Time, Lamp Hour Meter, Filter Usage, Projector Usage,
BIOS Version, Firmware Version, Data Version
Source Index, Horizontal Frequency, Vertical Frequency, Sync Polarity
Signal Type, Video Type, Sync Type, Interlace
Default
Factory Default
Clear Filter Usage
Clear Lamp Hour Meter
Current Signal
All Data
NOTE: Some menu items are not available depending on the input source.
39
쐏 Menu Descriptions & Functions [Picture]
5. Using On-Screen Menu
Using the Wall Color Correction [Wall Color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following eight options are available.
• OFF
• Light yellow
• Light blue
• Light rose
• Blackboard
• Light green
• Sky blue
• Pink
Using Picture Management [Picture Management]
This option allows you to adjust neutral tint for yellow, cyan or magenta.
There are 5 factory presets optimized for various types of images, or you can set user adjustable settings.
Presentation .......... Recommended for making a presentation using a PowerPoint file
Video ..................... Recommended for regular picture such as TV program
Movie .................... Recommended for movies
Graphic .................. Recommended for graphics sRGB ..................... Standard color values
User ...................... User adjustable
40
5. Using On-Screen Menu
NOTE: When “sRGB”, “Graphic”, “Video” or “Movie” is selected, the brightness decreases slightly when compared to “Presentation”. This is not a malfunction.
User Adjust (when using User)
When selecting user adjustable presetting (User), the submenu will be displayed.
You can customize each gamma or color. To do so, first select “User” and press the ENTER button, and then proceed the following steps.
Selecting Base Setting [Base Setting]
This feature allows you to use white balance or gamma values as reference data to optimize for various types of images. You can select one of the following five settings.
• Presentation
• Movie
• sRGB
• Video
• Graphic
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for :
Dynamic ................ Creates a high-contrast picture
Black Detail ........... Emphasizes detail in dark areas of the picture
Natural .................. Natural reproduction of the picture
Adjusting White Balance [Brightness RGB/Contrast RGB]
This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the screen; Contrast for each color (RGB) to adjust the white level of the screen.
Adjusting Brightness, Contrast, Sharpness, Color and Hue
Brightness ............. Adjusts the brightness level or the back raster intensity.
Contrast ................ Adjusts the intensity of the image according to the incoming signal.
Sharpness ............. Controls the detail of the image for Video.
Color ..................... Increases or decreases the color saturation level (not valid for RGB).
Hue ........................ Varies the color level from +/– green to +/– blue. The red level is used as reference. This adjustment is only valid for Video and Component inputs (not valid for RGB).
41
쐄 Menu Descriptions & Functions [Image]
5. Using On-Screen Menu
Enabling Auto Keystone [Auto Keystone]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn on the Auto Keystone feature, select “On”.
Correcting Vertical Keystone Distortion Manually [Keystone]
You can correct vertical distortion manually from the menu when “Auto Keystone” is turned off.
You can save the changes using the Keystone Save feature when you turn off the projector.
Saving Vertical Keystone Correction [Keystone Save]
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved when the projector is off.
Selecting Aspect Ratio [ Aspect Ratio]
Aspect Ratio allows you to select the best Aspect mode to display your source image. You can also display the Aspect
Ratio menu by pressing the “ASPECT” button on the remote control.
Wide Zoom Cinema Native Normal
When 4:3 is selected from the source (i.e. DVD player), the following selections will display:
Standard
4:3 Aspect
Normal
When 16:9 is selected from the source (i.e. DVD player), the following selections will display:
16:9 image displayed in 4:3 mode
Left and right stretched
Wide Zoom
Left and right stretched
Left and right stretched
Cinema
Left and right stretched to display the true aspect
Native
Native (RGB only): Turns off the Advanced AccuBlend feature. The projector displays the current image in its true resolution.
NOTE:
• While you are displaying an image at the projector’s native resolution or higher, “Native” is not available.
• You can adjust the image position for Cinema aspect. See “Cinema Position” for setting the image position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with a "Aspect Ratio" setting may raise concern about the infringement of copyrights which are protected by copyright law.
42
5. Using On-Screen Menu
Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)
This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.
When “Cinema” is selected in “Aspect Ratio”, the image is displayed with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when “Cinema” is selected in Aspect Ratio.
쐂 Menu Descriptions & Functions [Setup]
Using Off Timer [Off Timer]
You can set the timer so that the projector turns itself off at the preset time.
1. Use the SELECT 왖왔 to select your desired time between 30 minutes and 8 hours: Off, 0:30, 1:00, 2:00,
3:00, 4:00, 6:00 and 8:00.
2. Press the ENTER button.
3. The Off Timer starts counting down remaining time.
4. The projector turns off after the countdown is complete.
NOTE:
• To cancel the preset time, select “Off” for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the “Projector will turn off in 3 minutes” message will be displayed on the bottom of the screen.
Selecting Lamp Mode [Lamp Mode]
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
Normal Mode ........ This is the default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life (80% Brightness).
NOTE: If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Eco mode to protect the projector. When the projector is in Eco mode, the picture brightness decreases. When the projector comes back to normal temperature, the Lamp mode returns to Normal mode.
NOTE: Thermometer symbol indicates the lamp mode is automatically set to Eco mode because the internal temperature is too high.
43
Selecting Menu Language [Language]
You can choose one of 21 languages for on-screen instructions.
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and monochrome.
5. Using On-Screen Menu
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.
The preset choices are “Manual”, “Auto 5 sec”, “Auto 15 sec”, and “Auto 45 sec”. The “Auto 45 sec” is the factory preset.
Selecting a Color or Logo for Background [Background]
Use this feature to display a black/ blue screen or logo when no signal is available.
Selecting Projector Orientation [Orientation]
This sets your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
Enabling Key Sound and Error Sound [Beep]
This feature turns on or off the keypad sound or alarm when a button on the cabinet and the remote control is pressed or an error occurs.
44
5. Using On-Screen Menu
쐆 Menu Descriptions & Functions [Advanced]
Security
A keyword can be set for your projector to avoid operation by an unauthorized user using the Menu. When a keyword is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the projector cannot project an image.
To enable the Security function:
1. Select [Advanced] → [Security] and press the 왗 button to select “On”.
The [Keyword] screen will be displayed.
2. Type in a combination of the four SELECT buttons 왖왔왗왘 and press the ENTER button.
NOTE: A keyword must be four to 10 digits in length.
The [Confirm Keyword] screen will be displayed.
45
5. Using On-Screen Menu
3. Type in the same combination of SELECT buttons 왖왔왗왘 and press the ENTER button.
The confirmation screen will be displayed.
4. Select “Yes” and press the ENTER button.
The Security function has been enabled.
To disable the Security function:
1. Select [Advanced] → [Security] and press the 왘 button to select “Off”.
The Keyword confirmation screen will be displayed.
2. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the Security function will be disabled.
When the Security function is enabled and the projector is turned on, the projector will display a blue background.
To display an image at this time, press the MENU button to display the Keyword input screen.
Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE:
• The security disable mode is maintained until the main power is turned off (by setting the main power switch to “O” or unplugging the power cable).
• If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request code. Your request code is displayed in the Keyword Confirmation screen. In this example “K992-45L8-JNGJ-4XU9-1YAT-
EEA2” is a request code.
46
5. Using On-Screen Menu
Disabling the Cabinet Buttons [Cabinet Button Lock]
This option turns on or off the Cabinet Button Lock function.
NOTE:
• This Cabinet Button Lock does not affect the remote control and the PC Control functions.
• When the cabinet buttons are unlocked, pressing and holding the EXIT button for about 10 seconds will change the setting to enable.
• Key symbol indicates the Cabinet Button Lock is enabled.
Enabling High Speed Fan Mode [Fan Mode]
This option allows you to select two modes for fan speed: High speed mode and Auto mode.
High ...................... The built-in fans run at a fixed high speed.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
When you wish to cool down the temperature inside the projector quickly, select “High”.
NOTE: Select “High” if you continue to use the projector for consecutive days.
Selecting Signal Format [Signal Select]
[Computer]
Allows you to choose “Computer” for an RGB source such as a computer, or “Component” for a component video source such as a DVD player. Normally select “RGB/Component” and the projector automatically detects a component signal. However there may be some component signals that the projector is unable to detect. If this is the case, select “Component”. Select “Scart” in Computer 1 for the European Scart signal.
[Video & S-Video System Select]
This feature enables you to select composite video standards manually. Normally select “Auto”.
When you select the video standard for Video and S-Video, select the video standard from the pull-down menu.
This must be done for Video and S-Video respectively.
47
5. Using On-Screen Menu
(Advanced Page 2)
Enabling Power Management [Power Management]
When this option is on and there is no input for five minutes or more, the projector will automatically turn itself off.
Turning On Noise Reduction [Noise Reduction]
(not available for Video and S-Video signals)
Reduces video noise. Select “On” to enable the Noise Reduction feature.
Turning On Flicker Reduction [Flicker Reduction]
Reduces flicker which can occur in an interlaced signal. This feature is not available for RGB and HDTV signals.
NOTE: When the Flicker Reduction is ON, jagged lines can be visible depending on the signal. In that case, select OFF.
NOTE: This feature may not be available depending on your video equipment connected to the projector.
Setting Auto Adjust [Auto Adjust]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and stability. You can automatically make adjustment in two ways: Normal and Fine
Off ......................... The RGB image will not be automatically adjusted.
You can manually optimize the RGB image.
Normal .................. Default setting. The RGB image will be automatically adjusted. Normally select this option.
Fine ....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when “Normal” is selected.
Adjusting Position/Clock (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and vertically, and adjust Clock and Phase.
[Horizontal/Vertical]
Adjusts the image location horizontally and vertically.
This adjustment is made automatically when the Auto Adjust is turned on.
[Clock] (available for RGB and HDTV signals only)
Use this item with the “Auto Adjust off” to fine tune the computer image or to remove any vertical banding that might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be necessary when you connect your computer for the first time. This adjustment is made automatically when the Auto Adjust is turned on.
48
5. Using On-Screen Menu
[Phase] (available for RGB and HDTV signals only)
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident when part of your image appears to be shimmering.)
Use “Phase” only after the “Clock” is complete.
This adjustment is made automatically when the Auto Adjust is turned on.
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (DIN 8 Pin). It supports data rates from 4800 to 19200 bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate may be recommended for long cable runs).
쐊 Menu Descriptions & Functions [Information]
Displays the status of the current signal, remaining lamp (%), lamp/filter/projector usage time (hours) and version information. The Information has two pages. The Information included is as follows:
[Page 1]
Remaining Lamp Time (%)*
Lamp Hour Meter (H)
Filter Usage
Projector Usage
* The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the Remaining Lamp Time bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the lamp mode is set to Normal or Eco.
BIOS Version
Firmware Version
Data Version
[Page 2]
Source Index
Horizontal Frequency
Vertical Frequency
Sync Polarity
Signal Type
Video Type
Sync Type
Interlace
49
쐎 Menu Descriptions & Functions [Default]
5. Using On-Screen Menu
Returning to Factory Default [Factory Default]
The Factory Default feature allows you to change adjustments and setting to the factory preset.
[Current Signal]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: Brightness, Contrast, Color, Hue, Sharpness, Noise Reduction, Aspect Ratio,
Horizontal Position, Vertical Position, Clock, Phase and Picture Management.
[All Data]
Reset all the adjustments and settings for all the signals to the factory preset for source except the following:
Language, Security, Communication Speed, Remaining Lamp Time, Lamp Hour Meter, Filter Usage and Projector
Usage. To reset the lamp usage time, see “Clear Lamp Hour Meter” and “Clear Filter Usage”.
Resetting the Filter Usage Hours [Clear Filter Usage]
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press the ENTER button.
Clearing Lamp Hour Meter [Clear Lamp Hour Meter]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press the ENTER button.
NOTE: The projector will turn off and go into standby mode after 2100 hours (up to 3100 hours in Eco mode) of service. If this happens, do the following while in standby condition to clear values for the Lamp Hour Meter:
For 8767A/8070 press the HELP button on the remote control for a minimum of 10 seconds.
For 8771 press and hold the POWER and the EXIT buttons on the remote control simultaneously for a minimum of 10 seconds.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
Do this only after replacing the lamp.
50
6. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filter and replace the lamp.
� Cleaning or Replacing the Filter
The air-filter sponge keeps dust and dirt from getting inside the projector and should be cleaned after every 100 hours of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat.
CAUTION
• Turn off the projector, turn off the main power switch and unplug the projector before replacing the filter.
• Only clean the outside of the filter cover with a vacuum cleaner.
• Do not attempt to operate the projector without the filter cover.
To clean the air-filter:
Vacuum the filter-through the filter cover.
CU
To reset the filter usage time, from the menu, select [Default]
→ [Clear Filter Usage].
See also page 50 for resetting the filter usage time.
To replace the filter (sponge):
1. Remove the filter cover by pushing down on the catch of the cover until you feel it detach.
Catch
2. Gently peel off the filter (sponge) and replace it with the new one.
51
6. Maintenance
3. Reinstall the new filter cover.
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter, remove dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement lamp.
쐇 Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
ZOOM
SELE
CT
ON
/STA
ND
BY
PO
STA
WE
LAM
P
TUS
VID
EO
IDE
O
CO MPU
TER
-1
TER
-2
ADJ O
VID
EO IN
S-VID
EO IN
L/M
ONO
AUDIO
R
L/M
ONO
R
AUDIO
AU
DIO
OUT
COMPUTER 1 IN
PU
TER O
UT
AU
DIO
PC
CO
NTR
OL
CO
MPUTER 2 IN
AC
IN
FOC
US
CU
COMPUTER-2
COMPUTER-1
S-VIDEO
VIDEO
LAMP
WER
STATUS
ON/STAND BY
SELECT
52
6. Maintenance
쐋 Replacing the Lamp
After your lamp has been operating for 2000 hours (up to 3000 hours in Eco mode) or longer, the LAMP indicator in the cabinet will blink red and the message will appear. Even though the lamp may still be working, replace it at 2000 (up to
3000 hours in Eco mode) hours to maintain optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter. See page 50 .
CAUTION
• DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off, wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour for the lamp to cool before handling.
• DO NOT REMOVE ANY SCREWS except two lamp case screws. You could receive an electric shock.
• Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints in the glass surface might cause an unwanted shadow and poor picture quality.
• The projector will turn off and go into stand by mode after 2100 (up to 3100 hours in Eco mode) hours of service. If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to
3000 hours in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp replacement.
To replace the lamp:
Optional lamp and tools needed for replacement:
• Replacement lamp . 465-8767A (8767A/8070) or 465-8771 (8771).
• Phillips screwdriver or equivalent
NOTE: The two lamp houses are slightly different in appearance.
The following explanation uses drawings for the lamp 465-8767A.
1. Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.
2. Use a Philips screwdriver to push and release the tab.
Push up and remove the lamp cover.
Catch
Philips screwdriver
53
6. Maintenance
3. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condition. The two screws are not removable.
Remove the lamp housing by holding it.
Interlock
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
4. Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the Dukane replacement lamp 465-8767A (8767A/8070) or 465-8771 (8771) .
Order this from your Dukane dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
5. Reattach the lamp cover.
Slip the lamp cover back until it snaps into place.
54
6. Maintenance
6. Finally, select the menu → [Default] → [Clear Lamp Hour Meter] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in Eco mode) of service, the projector cannot turn on and the menu is not displayed. If this happens, do the following while in standby condition to clear values for the Remaining Lamp Time and the
Lamp Hour Meter:
For 8767A/8070 press the HELP button on the remote control for a minimum of 10 seconds.
For 8771 press and hold the POWER and the EXIT buttons on the remote control simultaneously for a minimum of 10 seconds.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
55
7. Appendix
� Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Blinking light
Steady light
Indicator Condition
Off
Green
Orange
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
Green
Orange
Projector Condition
The main power is off
The projector is getting ready to turn on.
Note
–
Wait for a moment.
Off Timer is enabled.
The projector is cooling down.
The projector is turned on.
The projector is in Standby.
–
Wait for a moment.
–
–
Status Indicator
Blinking light
Steady light
Indicator Condition
Off
Red 1 cycle (0.5 sec On,
2.5 sec Off)
2 cycle (0.5 sec On,
0.5 sec Of)
4 cycle (0.5 sec On,
0.5 sec Off)
6 cycle (0.5 sec On,
0.5 sec Off)
Green
Orange
Normal
Lamp cover error or lamp housing error
Temperature error
Fan error
Projector Condition
Lamp error
Re-firing the lamp (The projector is cooling down.)
Cabinet button is locked
Note
–
Replace the lamp cover or lamp housing correctly.
The projector is overheated. Move the projector to a cooler location.
Fans will not work correctly.
Lamp fails to light. Wait a full minute and then turn on again.
The projector is re-firing.
Wait for a moment.
You have pressed cabinet button when Cabinet Button is locked.
Lamp Indicator
Blinking light
Indicator Condition
Off
Red
Steady light Red
Projector Condition
Normal
Lamp has reached its end of life. Lamp replacement message will be displayed.
Lamp has been used beyond its limit. The projector will not turn on until the lamp is replaced.
Lamp mode is set to Eco mode
Note
–
Replace the lamp.
Replace the lamp.
– Green
56
7. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 56 .)
Problem
Does not turn on
Will turn off
No picture
Picture suddenly becomes dark
Color tone or hue is unusual
Image isn’t square to the screen
Picture is blurred
Image is scrolling vertically, horizontally or both
Remote control does not work
Check These Items
• Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on. See pages 22 and 23 .
• Ensure that the lamp cover is installed correctly. See page 54 .
• Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 3100 hours : Eco mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move the projector to a cooler location.
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• The lamp has reached the end of its usable life. Replace the lamp.
• Ensure that the Power Management is off. See page 48 .
• Use the VIDEO, the S-VIDEO or the COMPUTER button (the SOURCE button on 8771) on the remote control to select your source (Computer, Video or S-Video). See page 25 . If there is still no picture, press the button again.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page 41 .
• Remove the lens cap.
• Reset the settings or adjustments to factory preset levels using the “Default” in the Menu. See page 50 .
• Enter your registered keyword if the Security function is enabled. See page 45 .
• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screensaver or power management software.
• See also the next page.
• When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen) → To return to the Normal mode, select another available source.
* When the image is muted using the PIC-MUTE button on the remote control
→ Press the PIC-MUTE button again to return to the Normal mode.
* When the room where you' re presenting is particularly warm → Move the projector to a cooler location.
• Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 40 .
• Adjust "Hue" in "Picture". See page 41 .
• Reposition the projector to improve its angle to the screen. See page 27 .
• Use the Keystone correction function to correct the trapezoid distortion. See page 29 .
• Adjust the focus. See page 28 .
• Reposition the projector to improve its angle to the screen. See page 27 .
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See pages 13.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
• Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO or the COMPUTER button (the
SOURCE button on 8771) on the remote control to select your source (Video, S-Video or Computer).
See page 25 .
• Adjust the computer image manually with the Horizontal/Vertical in the “Advanced → Page 2”. See page 48 .
• Install new batteries.
8767A/8070: AAA
⳯2. See page 10 .
8771: Lithium coin cell (CR2032). See page 12 .
• Make sure there are no obstacles between you and the projector.
• Stand within 22 feet (7 m) of the projector. pages 10 for 8767A/8070 and 12 for 8771.
• See the POWER/STATUS/LAMP Indicator on page 56 .
Indicator is lit or blinking
Cross color in RGB mode
• Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. See page 31 .
• When “Off” is selected in Auto Adjust, adjust the computer image manually with Clock/Phase in “Advanced
→
Page 2” in the menu. See page 48 .
For more information contact your dealer.
57
7. Appendix
If there is no picture, or the picture is not displayed correctly.
• Power on process for the projector and the PC.
Be sure to connect the RGB cable between the projector and the computer before turning on the computer.
There are some notebook PCs, which do not output signal unless there is a projector or monitor connected first.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads
“0kHz”, this means there is no signal being output from the computer. See page 49 or go to next step.
• Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through external display selections.
• Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step. Refer to your computer’s documentation for detailed information.
• Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
• Mirroring on a PowerBook
* When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirroring” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
• Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple menu and arrange icons.
58
7. Appendix
� Specifications
This section provides technical information about the 8767A/8070/8771 Projector's performance.
Model Number 8767A/8070/8771
Optical
LCD Panel
Resolution
Lens
0.7" p-Si TFT active-matrix (with Micro Lens Array on
8767A
only)
8767A/8771: 1024
⳯ 768 pixels* native, up to UXGA
.
8070: 800
⳯ 600 pixels* native, up to UXGA with Advanced AccuBlend
8767A/8070/8771: Manual zoom and manual focus
F1.7 - 2.0 f=21.6 - 25.9 mm
Lamp
Image Size (Diagonal)
Projection Distance
Projection Angle
Keystone Correction
Electrical
Inputs
8767A/8070: 180W DC lamp (150W Eco mode)
8771: 130W DC lamp (110W Eco mode)
21 - 300 inches / 0.5 - 7.6 m
2.4 - 35.89 ft / 0.73 - 10.9 m
Tele: 9.5
° - 9.9°/ Wide: 11.5° - 12.0°
+/- 30
° Vertical (auto)
2 RGB/Component (D-Sub 15 Pin),
1 S-Video (DIN 4 Pin), 1 Video (RCA), 2 (L/R) RCA Audio,
1 Stereo Mini Audio, 1 PC Control (DIN 8 Pin)
Outputs
Video Compatibility
Scan Rate
Video Bandwidth
Color Reproduction
Horizontal Resolution
External Control
Sync Compatibility
Built-in Speaker
1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio (not available on VT47)
NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,
HDTV: 1080i, 1080i/50Hz, 720p, 576p, 480p, 480i/60Hz
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz
RGB: 80 MHz (-3dB)
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 540 TV lines
SECAM: 300 TV lines
YCbCr: 800 TV lines
RGB: 8767A/8771: 1024 dots (H)
⳯768 dots (V),
8070: 800 dots (H)
⳯600 dots (V)
RS232, IR
Separate Sync / Composite Sync / Sync on G
1W (monaural)
* Effective pixels are more than 99.99%.
59
7. Appendix
Power Requirement
Input Current
Power Consumption
100 - 240V AC, 50 / 60 Hz
8767A/8070: 2.7 - 1.4A (100 - 240V AC)
8771: 2.1 - 1.2A (100 - 240V AC)
8767A/8070: 8W in Standby mode /
250W in Lamp Normal mode / 200W in Lamp Eco mode
8771: 8W in Standby mode /
190W in Lamp Normal mode / 155W in Lamp Eco mode
Mechanical
Installation Orientation
Dimensions
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
11.6" (W) ⳯3.7" (H)⳯10.2" (D)
294mm (W) ⳯93mm (H)⳯260mm (D)
(not including protrusions)
Net Weight 6.5 lbs / 2.9 kg
Environmental Considerations Operational Temperatures : 41 ° to 95°F (5° to 35°C),
20% to 80% humidity (non-condensing)
Storage Temperatures : 14 ° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
Regulations For United States:
UL Approved (UL 60950)
Meets FCC Class B requirements
For Canada:
UL Approved (CSA 60950)
Meets DOC Canada Class B requirements
For Australia/New Zealand:
Meets AS/NZS CISPR.22 Class B
For Europe:
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
For additional information visit:
US : http://www.
dukcorp .com
/av
The specifications are subject to change without notice.
60
7. Appendix
� Cabinet Dimensions
AC IN
COMPUTER 2 IN AUDIO
PC CONTROL
MONITOR OUT
COMPUTER 1 IN
AUDIO OUT R
AUDIO
R AUDIO L/MONO
L/MONO
VIDEO IN
S-VIDEO IN
COMPUTER-2
ADJ.
AUTO
COMPUTER-1 S-VIDEO VIDEO
STATUS
LAMP
POWER
ON/STAND BY
SELECT
ZOOM
FOCUS
294 (11.6)
Lens center 71.5 (2.8)
Lens center
Unit: mm (inch)
61
62
7. Appendix
7. Appendix
� Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector
5
15
10
4 3
14
9
13
8
2
12
7
1
11
6
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
Pin No.
RGB Signal (Analog)
12
13
14
15
7
8
9
10
11
1
4
5
2
3
6
Red
Green or Sync on Green
Blue
Ground
Ground
Red Ground
Green Ground
Blue Ground
No Connection
Sync Signal Ground
SCART Sync
Bi-directional DATA (SDA)*
Horizontal Sync or Composite Sync
Vertical Sync
Data Clock*
* Only COMPUTER 1 input connector supported .
YCbCr Signal
Cr
Y
Cb
Cr Ground
Y Ground
Cb Ground
63
� Compatible Input Signal List
@
@
@
@
@
@
@ # VESA
@ # MAC
@ # SUN
@ # SGI
@ # VESA
@ # VESA
@ # MAC
@ # HP
VESA
MAC
VESA
VESA
VESA
MAC
VESA
VESA
IBM
VESA
IBM
IBM
VESA
VESA
VESA
VESA
NTSC
PAL
PAL60
SECAM
VESA
IBM
MAC
MAC
MAC
VESA
VESA
IBM
VESA
@ # SUN
@ # VESA
@ # VESA
@ # SXGA+
@ # HDTV (1080p)
@ # SDTV(576i)(625i)
@ # SDTV(576p)(625p)
@ # HDTV (1080i)(1125i)
@ # HDTV (1080i)(1125i)
@ # HDTV (720p)(750p)
@ # SDTV (480p)(525p)
@ # * VESA
@ # * VESA
@ # * VESA
@ # * VESA
DVD YCbCr
DVD YCbCr
Signal Resolution
( Dots )
–
–
–
–
640 ⳯ 480
640
⳯ 480
640 ⳯ 480
640 ⳯ 480
640 ⳯ 480
640
⳯ 480
640
⳯ 480
640 ⳯ 480
640 ⳯ 480
720
⳯ 350
720
⳯ 400
720 ⳯ 350
720 ⳯ 400
800
⳯ 600
800 ⳯ 600
800 ⳯ 600
800 ⳯ 600
800
⳯ 600
832
⳯ 624
1024 ⳯ 768
1024 ⳯ 768
1024
⳯ 768
1024
⳯ 768
1024 ⳯ 768
1024 ⳯ 768
1152
⳯ 864
1152 ⳯ 870
1152 ⳯ 900
1152 ⳯ 900
1280
⳯ 960
1280
⳯ 1024
1280 ⳯ 1024
1280 ⳯ 1024
1280
⳯ 1024
1280
⳯ 1024
1280 ⳯ 1024
1400 ⳯ 1050
1920
⳯ 1080
–
–
1920 ⳯ 1080
1920
⳯ 1080
1280
⳯ 720
–
1600 ⳯ 1200
1600
⳯ 1200
1600
⳯ 1200
1600 ⳯ 1200
–
–
# : Images in above flagged with # are compressed .
@ : Images in above flagged with @ are compressed .
* : Images in above flagged with * are not supported on other models.
81.13
79.976
91.146
–
67.5
15.6
31.5
33.75
67.5
68.681
61.796
71.736
60
63.981
69.89
78.125
28.125
45
31.47
75.0
81.25
87.5
93.75
15.734
15.625
53.674
49.725
35.5
48.363
56.476
60.241
60.023
68.677
31.469
37.927
39.44
39.44
35.16
37.879
48.077
46.88
Frequency H.
( kHz )
15.734
15.625
15.734
15.625
31.47
31.47
31.47
34.97
35
37.86
37.5
39.375
43.269
75
75.06
65.95
76.05
60
60.02
65.18
72.01
76.11
75.03
85.02
–
60 Progressive
50
50
60 Interlace
50 Interlace
60 Progressive
59.94 Progressive
60
65
70
75
59.94 Interlaced
50 Interlaced
70.09
85.04
87.85
87.85
56.25
60.32
72.19
75
85.06
74.55
43 Interlaced
60
70.07
74.93
75.03
85
60
60
66.67
66.67
72.81
75
75
85.01
Refresh Rate
( Hz )
60
50
60
50
59.94
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600 ⳯1200) is supported for separate sync signal only.
64
7. Appendix
� PC Control Codes and Cable Connection
PC Control Codes
Function
POWER ON
Code Data
02H 00H 00H 00H 00H 02H
POWER OFF 02H 01H 00H 00H 00H 03H
INPUT SELECT COMPUTER 1 02H 03H 00H 00H 02H 01H 01H 09H
INPUT SELECT COMPUTER 2 02H 03H 00H 00H 02H 01H 02H 0AH
INPUT SELECT VIDEO 02H 03H 00H 00H 02H 01H 06H 0EH
INPUT SELECT S-VIDEO
PICTURE MUTE ON
PICTURE MUTE OFF
02H
02H
02H
03H
10H
11H
00H
00H
00H
00H
00H
00H
02H
00H
00H
01H
12H
13H
0BH 13H
SOUND MUTE ON
SOUND MUTE OFF
02H 12H 00H 00H 00H 14H
02H 13H 00H 00H 00H 15H
NOTE: Contact your local dealer for a full list of the PC Contorol Codes if needed.
7. Appendix
Cable Connection
Communication Protocol
Baud rate ........................................ 19200 bps
Data length ..................................... 8 bits
Parity .............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
65
PC Control Connector (DIN-8P)
To RxD of PC
5
8
7
2
4
1
6
3
To GND of PC To TxD of PC
NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.
7. Appendix
66
쐆 Optional Presentation Remote Control Kit (PR52KIT)
7. Appendix
The PR52KIT is an optional remote control kit for operating your projector and performing your computer mouse operations.
Package List
• RD-408E remote control unit ....... 1 • AAA batteries ................... 2
• Mouse receiver ............................ 1 • User's manual .................. 1
Part Names and Functions of the Remote Control
12
15
16
18
19
22
24
25
27
29
6
8
10
1
3
5
OFF
MAGNIFY
POWER
LASER
POINTER
ON
PAGE
UP
DOWN
MENU
R-CLICK
PICTURE SOURCE VIEWER
ASPECT AUTO ADJ.
SLIDE
PIC-MUTE HELP
VOLUME FOCUS ZOOM
FREEZE 3D REFORM
PJ OFF MOUSE
14
2
4
7
9
11
13
17
20
21
23
26
28
67
1. Infrared Transmitter/Laser Pointer
Transmits an infrared signal when any button other than LASER is pressed.
Direct the remote control toward the remote sensor on the projector cabinet.
Beams a laser light when the Laser button is pressed.
CAUTION:
* Do not look into the laser pointer while it is on.
* Do not point the laser beam at a person.
2. Remote Jack
Not available on this model.
3. LED
Flashes when any button is pressed.
4. POWER ON Button
When the main power is on, you can use this button to turn your projector on.
NOTE: To turn on the projector, press and hold the
POWER ON button for a minimum of two seconds.
5. POWER OFF Button
You can use this button to turn your projector off.
NOTE: To turn off the projector, press the POWER OFF button twice.
6. MAGNIFY (+)(–) Buttons
Use these buttons to adjust the image size.
The image can be magnified about the center of the screen up to 400%.
7. LASER Button
Press and hold this button to activate the laser pointer.
When lit, you can use the laser to draw your audience's attention to a red dot that you can place on any object.
8. POINTER Button
Not available on this model.
9. PAGE UP/DOWN Buttons*
Use these buttons to operate your computer with the supplied remote mouse receiver. You can use these buttons to scroll the viewing area of the window or to move to the previous or next slide in PowerPoint on your computer.
10. MENU Button
Displays the menu for various settings and adjustments.
11. Mouse Button
In Mouse mode*, this button works as your computer mouse.
In Projector mode, this button is used for projector’s menu operation and moving the magnified image.
12. ENTER Button
Executes your menu selection and activates items selected from the menu.
13. EXIT Button
Returns to the previous menu.
While you are in the main menu, pressing this button will close the menu.
14. L-CLICK Button*
Works as the mouse left button when the supplied remote mouse receiver is connected with your computer.
15. R-CLICK Button*
Works as the mouse right button when the supplied remote mouse receiver is connected with your computer.
16. PICTURE Button
Press this button to display the Picture window. Each time this button is pressed, the option will be changed:
Wall Color → Picture Management → Brightness →
Contrast → Sharpness → Color → Hue
17. SOURCE Button
Use this button to select a video source such as a
PC, VCR or DVD player.
Press and release this button quickly to display the
Source List.
Each time this button is pressed for a minimum of
ONE second, the input source will change.
If no input signal is present, the input will be skipped.
18. ASPECT Button
Press this button to display the Aspect Ratio select screen.
7. Appendix
19. AUTO ADJ. Button
Use this button to adjust an RGB source for an optimal picture.
20. VIEWER Button
Not available on this model.
21. SLIDE +/- Buttons
Not available on this model.
22. PIC-MUTE Button
This button turns off the image and sound for a short period of time. Press again to restore the image and sound.
23. HELP Button
Provides the Information screen.
24. VOLUME +/– Buttons
Press (+) to increase the volume and (–) to decrease it.
25. FOCUS +/- Buttons
Not available on this model.
26. ZOOM +/- Buttons
Use to finely adjust the image on the screen.
27. FREEZE Button
This button will freeze a picture. Press again to resume motion.
28. 3D REFORM Button
Not available on this model.
29. PJ 왗 OFF 왘 MOUSE Slide Switch
Use to switch mouse button operation modes between
Mouse and Projector. Setting to OFF will disable all the buttons on the remote control.
*NOTE: The PAGE UP/DOWN, L-CLICK, R-CLICK and MOUSE
(as computer mouse) buttons are available only when the PJ
왗 OFF 왘 MOUSE Slide Switch is set to MOUSE.
68
7. Appendix
Battery Installation
1
Remove the battery cover.
NOTE: Do not pull the battery cover by force. Doing so can result in it coming off.
2
2
Remove both old batteries and install new ones (AAA). Ensure that you have the batteries' polarity (+/ –) aligned correctly.
1
2
1
3
Slip the cover back over the batteries until it snaps into place.
NOTE: Do not mix different types of batteries or new and old batteries.
Operating Range for Wireless Remote Control
Remote sensor on projector cabinet
7m/22 feet
30 °
30 °
30 °
30 °
7m/22 feet
Remote control
• The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of the remote sensor on the projector cabinet.
• The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls on the sensor.
Weak batteries will also prevent the remote control from properly operating the projector.
Remote Control Precautions
• Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• If you will not be using the remote control for a long time, remove the batteries.
• Do not place the batteries upside down.
• Do not use new and old batteries together, or use different types of batteries together.
69
7. Appendix
Using the Laser Pointer
You can use the laser to draw your audience's attention to a red dot that you can place on any object.
CAUTION:
• Do not look into the laser pointer while it is on.
• Do not point the laser beam at a person.
• Do not allow children to use the laser pointer.
Press and hold the LASER button to activate the laser pointer.
ZOOM
FOC
US
LASER
AC
IN
To disable the laser pointer, set the function switch to “Off”.
Decide whether to enable or disable laser, then set the switch as necessary using the tip of a thin ball-point pen. On this model, the other selector switch is not used.
ON
OFF
Laser enable/disable switch
Not used
On: Enabled (the laser lights when the LASER button is pressed) [Factory default]
Off: Disabled (the laser does not light even when the LASER button is pressed)
Disable the laser when using in an environment in which the unit is accessible to children.
Using Remote Mouse Receiver (8767A/8070 only)
See page 34 .
70
7. Appendix
쐊 Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem more efficiently.
* Print the following pages.
Frequency of occurrence 䡺 always 䡺 sometimes (How often?_____________________) 䡺 other (__________________)
Power
No power (POWER indicator does not light green) See also “Status Indicator (STATUS)”.
Shut down during operation.
Power cable's plug is fully inserted into the wall outlet.
Main power switch is pressed to the ON position.
Power cable's plug is fully inserted into the wall outlet.
Lamp cover is installed correctly .
Lamp cover is installed correctly .
Power Management is turned off (only models with the Power
Management function).
Lamp Hour Meter (lamp operation hours) was cleared after lamp replacement.
No power even though you press and hold the POWER button for a minimum of 2 seconds.
Video and Audio
Sleep Timer is turned off (only models with the Sleep Timer function ).
No image is displayed from your PC or video equipment to the projector.
Still no image even though you connect the projector to the PC first, then start the PC.
Enabling your notebook PC’s signal output to the projector.
• A combination of function keys will enable/disable the external display. Usually, the combination of the “Fn” key along with one of the 12 function keys turns the external display on or off.
No image (blue background, logo, no display).
Still no image even though you press the AUTO ADJUST button.
Still no image even though you carry out “Reset” in the projector’s menu.
Signal cable's plug is fully inserted into the input connector
A message appears on the screen.
( _____________________________________________ )
The source connected to the projector is active and available.
Still no image even though you adjust the brightness and/or the contrast.
Input source's resolution and frequency are supported by the projector.
Image is too dark.
Remains unchanged even though you adjust the brightness and/or the contrast.
Image is distorted.
Image appears to be trapezoidal (unchanged even though you carry out the “Keystone" or “3D Reform” adjustment).
Other
Remote control does not work.
No obstacles between the sensor of the projector and the remote control.
Projector is placed near a fluorescent light that can disturb the infrared remote controls.
One or more remote sensors are enabled (only models with the Remote Sensor Selection function).
Batteries are new and are not reversed in installation.
If present on the remote control, projector selector switch is not used.
Parts of the image are lost.
Still unchanged even though you press the AUTO ADJUST button.
Still unchanged even though you carry out “Reset” in the projector’s menu.
Image is shifted in the vertical or horizontal direction.
Horizontal and vertical positions are correctly adjusted on a computer signal.
Input source's resolution and frequency are supported by the projector.
Some pixels are lost.
Image is flickering.
Still unchanged even though you press the AUTO ADJUST button.
Still unchanged even though you carry out “Reset” in the projector’s menu.
Image shows flickering or color drift on a computer signal.
Image appears blurry or out of focus.
Still unchanged even though you checked the signal’s resolution on PC and changed it to projector’s native resolution.
Still unchanged even though you adjusted the focus.
No sound.
Audio cable is correctly connected to the audio input of the projector.
Still unchanged even though you adjusted the volume level.
AUDIO OUT is connected to your audio equipment (only models with the AUDIO OUT connector).
Buttons on the projector cabinet do not work ( only models with the Key Lock function).
Cabinet Button Lock is not turned on or is disabled in the menu.
Still unchanged even though you press and hold the EXIT button for a minimum of 10 seconds.
71
7. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector
Model number:
Serial No.:
Date of purchase:
Lamp operating time (hours):
Lamp Mode:
Information on input signal:
䡺 Normal 䡺 Eco
Horizontal synch frequency [ ] kHz
Vertical synch frequency
Synch polarity
Synch type
[ ] Hz
H 䡺 (+) 䡺 (–)
V 䡺 (+) 䡺 (–)
䡺 Separate 䡺 Composite
䡺 Sync on Green
STATUS Indicator:
Steady light
Flashing light
䡺 Orange 䡺 Green
[ ] cycles
Remote control model number:
Installation environment
Screen size: inch
Screen type: 䡺 White matte 䡺 Beads 䡺 Polarization
䡺 Wide angle 䡺 High contrast
Throw distance: feet/inch/m
Orientation: 䡺 Ceiling mount 䡺 Desktop
Power outlet connection:
䡺 Connected directly to wall outlet
䡺 Connected to power cord extender or other (the number of connected equipment______________)
䡺 Connected to a power cord reel or other (the number of connected equipment______________)
Computer
Manufacturer:
Model number:
Notebook PC 䡺 / Desktop 䡺
Native resolution:
Refresh rate:
Video adapter:
Other:
Projector
PC
DVD player
Signal cable
Standard or other manufacturer’s cable?
Model number: Length: inch/m
Distribution amplifier
Model number:
Switcher
Model number:
Adapter
Model number:
Video equipment
VCR, DVD player, Video camera, Video game or other
Manufacturer:
Model number:
72
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [email protected]
Phone: (630) 762-4040
Orders: (800) 676-2485
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Audio Visual Products
Part # 401-8767A_8771_8070-00
Advertisement
