Munters ST5026 Owner's manual

Munters ST5026 Owner's manual
Temperature Controller
ST 5026
USER'S MANUAL
67
Aerotech, Inc.
4215 Legion Dr. Mason, MI 48854-1036 USA
Ph. (517) 676-7070 Fax (517) 676-7078
F O R M : QM 1339
January 2000
PRECAUTIONS
TABLE OF CONTENTS
Page
PRECAUTIONS .................................................................. 3
FEATURES ........................................................................ 4
LOCATION OF THE CONTROLS ...................................... 6
Controller Status Leds ...................................................... 7
Internal Switches ............................................................... 7
INSTALLATION .................................................................. 8
Mounting Instructions ......................................................... 8
Connections ..................................................................... 8
Heating / Cooling Option ................................................... 9
Temperature Probes ......................................................... 9
CHANGING THE PARAMETER SETTINGS ...................... 12
The Meaning of a Flashing Display ................................... 12
Locking the Parameters Settings ...................................... 13
TEMPERATURE SETTINGS ............................................. 13
Temperature Units ............................................................ 13
Viewing Temperatures ...................................................... 13
Temperature Set Point ...................................................... 16
Temperature Curve ........................................................... 17
VENTILATION SETTINGS ................................................. 21
Cooling Operation............................................................. 21
Minimum Ventilation Cycle ................................................ 23
Minimum Ventilation Compensation .................................. 27
Ventilation Settings ........................................................... 29
Mist Cooling ..................................................................... 30
HEATER SETTINGS .......................................................... 33
ALARM SETTINGS ............................................................ 35
TROUBLESHOOTING GUIDE ........................................... 37
TECHNICAL SPECIFICATIONS ........................................ 40
FACTORY SETTINGS ........................................................ 41
2
QM 1339.rev.03
We strongly recommend installing supplementary natural
ventilation, a failure alarm system as well as a back-up thermostat on at least one cooling stage (refer to the wiring diagram
enclosed with this user's manual to connect the thermostat).
Although fuses at the input and outputs of the controller
protect its circuits in case of an overload or overvoltage, we
recommend installing an additional protection device on the
supply circuit as well as an external relay on all ON-OFF stages to prolong the life of the controller.
The room temperature where the controller is located MUST
ALWAYS REMAIN BETWEEN 32°F AND 104°F (0°C TO 40°C).
To avoid exposing the controller to harmful gases or excessive humidity, it is preferable to install it in a corridor.
DO NOT SPRAY WATER ON THE CONTROLLER
FOR CUSTOMER USE
Enter below the serial number located on
the side of the controller and retain this
information for future reference.
Model number:
Serial number:
Date installed:
___ST 5026___
_____________
_____________
QM 1339.rev.03
3
ST 5026
FEATURES
The ST 5026 is an electronic device used for environmental control in livestock buildings. It allows the user to maintain a specified target temperature by controlling the operation of ventilation and heating equipment. Six
stages of constant-speed cooling fans can be connected to the controller,
as well as two stages of either constant-speed fans or heating units. In
addition, the last cooling stage can be configured as a mist cooling stage.
The main features of the ST 5026 are as follows:
TEMPERATURE CURVE
The controller can be set to automatically change the temperature set
point over a given period of time in accordance with the user's requirements by specifying a temperature curve with up to six different points.
FOUR INDEPENDENT TEMPERATURE PROBE INPUTS
THREE-DIGIT DISPLAY
Up to four temperature probes can be connected to the controller in order to
obtain a more accurate reading of the average room temperature and a faster
reaction time.
A three-digit display provides a high level of accuracy, allowing the user to
specify a temperature to within one tenth of a degree (in Fahrenheit or Celsius units).
OVERLOAD AND OVERVOLTAGE PROTECTION
PILOT LIGHTS
Pilot lights indicating the state of outputs allow the user to monitor the
operation of the system without having to enter the building.
MINIMUM VENTILATION CYCLE
When ventilation is not required for cooling, the first stage fans can be operated either continuously or intermittently to reduce the level of humidity and
supply oxygen to the room.
MINIMUM VENTILATION COMPENSATION CURVE
An outside probe can be connected to the controller to adjust the minimum
ventilation cycle as a function of outside temperature.
Fuses are installed at the input and outputs of the controller to protect its
circuitry in the case of an overload or overvoltage.
COMPUTER CONTROL
The controller can be connected to a computer, thus making it possible to
centralize the management of information and diversify control strategies.
CONTROL OF AIR INLET MOVEMENT
If the ST 5026 is used in combination with a SB 2000 controller, the movement of the air inlets can be coordinated with the operation of the fans using
a potentiometer located on the curtain machine or baffle actuator. This
allows the air inlets to be adjusted correctly, without the influence of uncontrollable factors such as wind or air from adjoining rooms. When tunnel
ventilation is being used, the SB 2000 closes the air inlets.
HIGH/LOW TEMPERATURE ALARM OUTPUT
RAMPING OPTION
The ramping option periodically calculates an optimal timer cycle to smooth
the transition between minimum ventilation and full operation of stage 1
fans.
4
QM 1339.rev.03
QM 1339.rev.03
5
ST 5026
LOCATION OF THE CONTROLS
CONTROLLER STATUS LEDS
LED
ME AN IN G
S TAGE S 1-2
F L A S H E S W H E N S TA G E 1 F A N S A R E O N . T U R N S O N W H E N S TA G E
2 FA NS A RE ON.
S TAGE S 3-4
F L A S H E S W H E N S TA G E 3 F A N S A R E O N . T U R N S O N W H E N S TA G E
4 FA NS A RE ON.
S TAGE S 5-6
F L A S H E S W H E N S TA G E 5 F A N S A R E O N .
6 FA NS A RE ON.
S TAGE 7 /
H E AT E R B
T U R N S O N W H E N S TA G E 7 F A N S O R H E A T IN G U N IT S A R E O N .
S TAGE 8 /
H E AT E R A
T U R N S O N W H E N S TA G E 8 F A N S O R H E A T IN G U N IT S A R E O N .
T E M P.
CURVE
TU R N S O N W H E N TH E TE M P E R A TU R E C U R V E IS A C TIV A TE D .
D E F. P R O B E
TU R N S O N W H E N A D E F E C T IV E P R O B E IS D E T E C T E D .
ALARM
TU R N S O N W H E N A N A L A R M IS D E T E C T E D .
INTERNAL SWITCHES
T U R N S O N W H E N S TA G E
ON
1
2
3
4
5
6
7
8
9 10 11 12
The internal switches are located on the inside of the front cover. When
the controller is shipped from the factory, all the switches are set to OFF.
ST5026
BFSPUFDI-!JOD/!!!Nbtpo-!NJ!59965!VTB
S E T T IN G S
#
OFF
ON
1
UNLOC KED PARAMETERS
LOC KED PARAMETERS
2
FAHRENHEIT D EGREES
C ELSIUS D EGREES
3
NO HEATING STAGES
HEATING
4
1 HEATER
2 HEATERS
5
STAGE 1 WITHOUT RAMPING
STAGE 1 WITH RAMPING
6
OUTSID E PROBE D ISABLED
OUTSID E PROBE ENABLED
7
RESERVED
8
RESERVED
9
RESERVED
10
RESERVED
11
RESERVED
12
6
QM 1339.rev.03
NORMAL SETTINGS
AD VANC ED SETTINGS
QM 1339.rev.03
7
ST 5026
INSTALLATION
MOUNTING INSTRUCTIONS
HEATING / COOLING OPTION
Open the latch and lift the cover. Remove the black caps located on each of
the four mounting holes. Mount the enclosure on the wall using four screws.
Be sure the electrical knockouts are at the bottom of the enclosure in order
to prevent water from entering the controller. Insert the screws in the mounting
holes and tighten. Fasten the four black caps provided with the controller onto
the four mounting holes. The enclosure must be mounted in a location that
will allow the cover to be completely opened right up against the wall.
Stages 7 and 8 can operate as heating or cooling stages.
ðSet switches # 3 and # 4 to OFF to use both
stages for cooling.
ðSet switch # 3 to ON and switch # 4 to OFF to
use Stage 8 for heating and Stage 7 for cooling.
ðSet switches # 3 and # 4 to ON to use both
stages for heating.
CONNECTIONS
To connect the controller, refer to the wiring diagram enclosed with this user's
manual.
n
Set the voltage switch to the appropriate voltage.
n
Use the electrical knockouts provided at the bottom of the enclosure. Do
not make additional holes in the enclosure, particularly on the top of the
enclosure when using a SL 1400 communication board.
n
If metallic cable holders are used to secure cables entering the
enclosure, use the ground plate provided with the controller. Connect
the ground wire to the ground stud on the plate.
n
For the heating stages, it may be necessary to install a transformer in
order to supply the appropriate voltage to the heating unit.
ALARM CONNECTION: There are two types of alarms on the market. One
type activates when current is cut off at its input, whereas the other activates
when current is supplied at its input. For an alarm of the first type, use the
NO terminal as shown on the wiring diagram. For an alarm of the second type,
use the NC terminal.
!
WARNING
8
ALL WIRING MUST BE DONE BY AN AUTHORIZED ELECTRICIAN AND MUST COMPLY WITH APPLICABLE CODES, LAWS
AND REGULATIONS. BE SURE POWER IS OFF BEFORE DOING ANY WIRING TO AVOID ELECTRICAL SHOCKS AND EQUIPMENT DAMAGE.
QM 1339.rev.03
ON
3
4
Note that if only one stage is used for heating, it must be Stage 8.
TEMPERATURE PROBES
1
Connecting the Probes
The controller is supplied with one indoor temperature probe. Three additional
indoor probes can be connected to obtain more accurate readings or to
control different parts of the building. In addition, an outdoor probe can be
connected if the compensation function on the minimum ventilation cycle is
needed (see the chapter on ventilation).
ð
Use terminals # 2, 3 and 4 to connect additional indoor probes and
terminal # 5 to connect the outdoor probe, as shown on the wiring diagram
enclosed.
CAUTION: Probes operate at low voltage and are isolated from the supply.
Be sure that probe cables remain isolated from all high voltage sources. In
particular, do not route the probe cables through the same electrical knockout
as other cables. Do not connect the shield from the probe cable to an input
or a ground.
QM 1339.rev.03
9
ST 5026
ST 5026
2
Extending the Probes
Each probe can be extended up to 500 feet (150 meters). To extend a probe:
n
Use a shielded cable of outside diameter between 0.245 and 0.260 in
(6.22 and 6.60 mm) (the cable dimensions should not be under 18
AWG) to ensure the cable entry is liquid tight. Do not ground the
shielding.
n
It is preferable to solder the cable joint to ensure a proper contact
between the two cables.
To identify the defective probe:
n
Set the selection knob to ROOM
TEMPERATURE . The room temperature is displayed.
n
Press the push-button. If the probe
connected to input # 1 and supplied with the controller is not defective, the letters"PR1" are displayed, alternating with the temperature measured by the probe.
If the probe is defective, the letters "PR1" are displayed, alternating
with the letter "P".
CAUTION: Do not run probe cables next to other power cables. When
crossing over other cables, cross at 90°.
For each additional probe connected to the controller:
3
Installing the Outside Probe
n
Run the outside probe cable on the north side of the building, 6 ft (2 m)
below the eave, inside a pale colored conduit. Avoid installing the
probe in direct sunlight or exposed to the rain.
n
Be sure the probe cable is isolated from sheet metal or any other
conductive material.
n
Be sure no cable joint is exposed to air or water.
4
n
Press the push-button once again. If the probe is not defective, the
letters "PR#" (where # is the number of the input to which the probe is
connected) are displayed, alternating with the temperature measured
by the probe. If the probe is defective, the letters "PR#" are displayed, alternating with the letter "P".
Outside Probe: If the outside probe is
defective, the display shows the letter
"P" when the parameter selection knob
is set to OUTSIDE TEMP.
Defective Probes
If a defective probe is detected, the Defective Probe Pilot Light turns on. The
room temperature shown on the display is then the average temperature
measured by the probes in working condition. The controller will operate
according to this temperature.
10 QM 1339.rev.03
QM 1339.rev.03
11
CHANGING THE PARAMETER SETTINGS
THE MEANING OF A FLASHING DISPLAY
TEMPERATURE SETTINGS
TEMPERATURE UNITS
Temperatures can be displayed in either Celsius or
Fahrenheit units
The display will flash in certain cases and not in others.
The flashing indicates that the
value shown can be adjusted.
A value that is not flashing
cannot be adjusted.
n
ON
Set internal switch # 2 to the desired position:
• ON to display temperatures in Celsius units.
• OFF to display temperatures in Fahrenheit units.
2
VIEWING TEMPERATURES
LOCKING THE PARAMETER SETTINGS
The parameter settings can be locked to prevent accidentally modifying
them. When the settings are locked, only the temperature set point can be
modified (as long as the temperature curve is deactivated).
To lock the parameter settings:
n
Set internal switch # 1 to ON. The Locked Parameter Pilot Light turns
on.
To unlock the parameter settings:
n
The readout can display values from
-40.0oF to 120oF ( -40.0oC to 48.9oC).
When the temperature drops below
-9.9 degrees, the negative sign is
displayed separately, alternating with
the numerical value.
1
Viewing Room Temperature
The room temperature is the average value of all temperatures measured by
activated probes in proper operating condition.
n
Set internal switch # 1 to OFF. The Locked Parameter Pilot Light
turns off.
2
Set the selection knob to ROOM TEMPERATURE / PROBE TEMP.
The room temperature is displayed.
Viewing Outside Temperature
The outside temperature can be displayed only if an outside probe has been
connected to terminal # 5 and internal switch # 7 is set to ON.
n
12 QM 1339.rev.03
Set the selection knob to OUTSIDE — TEMP. / COMPENSATION.
The outside temperature is displayed.
QM 1339.rev.03
13
ST 5026
ST 5026
3
Viewing Probe Temperatures
The controller can display probe temperatures individually. Probes can also
be turned on or off to control the temperature in different parts of the building.
n
Set selection knob to ROOM TEMPERATURE / PROBE TEMP. The
average room temperature is displayed.
4
Viewing Minimum / Maximum Temperatures
The minimum and maximum temperatures are the lowest and highest temperature values recorded since the last reset. Maximum and minimum
temperatures values are recorded for the average room temperature as well
as for individual probe temperatures.
n
Set the selection knob to ROOM TEMPERATURE / PROBE TEMP.
The room temperature is displayed.
n
Turn the adjustment knob clockwise by one notch. The minimum
temperature is displayed, alternating with the letters "Lo".
n
Press the push-button once again to display the letters "Pr 1" alternating with the state of probe 1, i.e. ON / OFF (flashing). When a
probe is activated, it is used in the calculation of the average room
temperature.
Turn the adjustment knob clockwise one notch further. The maximum temperature is displayed, alternating with the letters "Hi".
n
Turn the adjustment knob clockwise a third notch. The room temperature is displayed again.
n
Use the adjustment knob to change the state of the probe.
n
For each individual probe, press the push-button. The temperature
reading from probe x is displayed, alternating with the letters "Pr x".
n
For each additional probe, press the push-button. The state of probe
is displayed, alternating with the letters "Pr x", etc.
n
Turn the adjustment knob clockwise by one notch. The minimum
temperature is displayed, alternating with the letters "Lo".
n
Turn the adjustment knob clockwise one notch further. The maximum
temperature is displayed, alternating with the letters "Hi".
n
Turn the adjustment knob clockwise a third notch. The probe temperature is displayed again.
n
For each additional probe, press the push-button. The temperature
reading from probe x is displayed, alternating with the letters "Pr x".
n
n
n
Press the push-button. The temperature reading from probe 1 is displayed, alternating with the letters "Pr 1".
For each additional probe, press the push-button. The temperature
reading from probe x is displayed, etc.
NOTES:
i) At least one probe must be activated at all times. If only one probe
remains active, the controller will lock the on/off switch for that probe.
ii) The display returns to the average room temperature after one minute.
iii) Initially, only probe one is activated.
NOTE: If you let the display flash for more than 10 seconds, the controller
resets the minimum and maximum temperatures currently in memory (the
display stops flashing to indicate that the reset has been done).
14 QM 1339.rev.03
QM 1339.rev.03
15
ST 5026
ST 5026
TEMPERATURE SET POINT
TEMPERATURE CURVE
The user can define a temperature curve to adjust the set point automatically
over a given time period.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
curve is deactivated (see following section).
d4
d25
○
○
d50
d70
○
○
○
○
○
d35
○
○
○
○
○
○
○
○
○
NOTE: The temperature set point can be adjusted only if the temperature
○
Use the adjustment knob to adjust the set point to the desired value.
○
n
○
Set the selection knob to SET POINT / TEMP. CURVE.The current set
point flashes on the display.
○
n
○
○
○
○
○
○
Adjusting the Temperature Set Point
To1
To2
To3
To4
To5
To6
○
The temperature set point is the target room temperature. It can be adjusted between -40.0°F and 99.9°F (-40.0°C and 37.7°C).
○
Temperature
d80 Days
A curve is defined using six points. Each point specifies a day number and
a set point for that day. Once the points of the curve are defined, the curve
must be activated. The controller will change the temperature set point every
hour in a linear fashion between consecutive points of the curve. When the
last point of the curve is reached, the temperature set point for that day is
maintained until the curve is reactivated.
NOTES :
i) All six points of the curve must be specified. If six points are not needed,
repeat the last temperature value for each unnecessary point.
ii) Certain restrictions apply to reduce the risk of errors:
− The highest possible day number is 99.
− Decreasing day numbers are not allowed.
− Increasing temperatures are not allowed.
− The temperature variation cannot exceed 3°F (1.6°C) per day.
16 QM 1339.rev.03
QM 1339.rev.03
17
ST 5026
ST 5026
1
n
n
Specifying the Curve
Set the selection knob to SET
POINT / TEMP. CURVE. The
current temperature set point
flashes on the display.
Press the push-button. The word OFF is displayed indicating that the
temperature curve is deactivated. If this is not the case, see below to
deactivate the curve.
Repeat the following steps for each of the six points:
2
Activating the Temperature Curve
If you have just finished specifying the points on the curve:
n
Press the push-button once again. The word OFF flashes on the
display.
n
Turn the adjustment knob clockwise one notch. The word ON flashes
on the display and the Temperature Curve Pilot Light flashes, indicating that the temperature curve is now activated.
n
Set the selection knob to ROOM TEMPERATURE.
n
Press the push-button once again. The day number is displayed,
alternating with the word "day".
If you have previously defined the points on the curve:
n
Using the adjustment knob, set the day number to the desired value.
n
n
Press the push-button once again. The current temperature set point
is displayed, alternating with the word "set".
Set the selection knob to SET POINT / TEMP. CURVE. The current
value of the temperature set point flashes on the display.
n
Press the push-button. The word OFF is displayed.
Using the adjustment knob, adjust the set point to the desired value.
n
Press the push-button to display the points of the curve currently
defined until the word OFF appears (thirteen clicks).
n
Turn the adjustment knob clockwise one notch. The word ON flashes
on the display and the Temperature Curve Pilot Light flashes, indicating that the temperature curve is now activated.
n
Set the selection knob to ROOM TEMPERATURE.
n
Once the six points of the curve have been specified, activate the curve as
explained below.
NOTE: Make sure the temperature curve is deactivated before specifying new points (see below).
18 QM 1339.rev.03
QM 1339.rev.03
19
20 QM 1339.rev.03
Temperature
Set Point
Room
Temp.
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
1234567890
Start Temp Start Temp Start Temp Start Temp Start Temp Start Temp Start Temp
Stage 2
Stage 7
Stage 3
Stage 4
Stage 6
Stage 5
Stage 8
Set the selection knob to ROOM TEMPERATURE.
Timer Temp.
Range
Stage 1
n
Minimum
Ventilation
Cycle
Turn the adjustment knob counterclockwise one notch. The word
OFF flashes on the display and the Temperature Curve Pilot Light
turns off, indicating that the temperature curve is now deactivated.
1.5 oF
n
1.5 oF
Press the push-button to display the points of the curve actually
defined until the word ON appears (fourteen clicks).
1.5 oF
n
STAGE 6
Set the selection knob to SET POINT / TEMP. CURVE. The current
temperature set point is displayed.
Ventilation
Level
n
1.5 oF
Deactivating the Temperature Curve
STAGE 7
4
STAGE 1
Use the adjustment knob to set the day number to the desired value.
STAGE 2
n
STAGE 3
Press the push-button. The current day number is displayed, alternating with the letters "cur.day".
STAGE 4
n
1.5 oF
Set the selection knob to SET POINT / TEMP. CURVE. The current
temperature set point is displayed.
STAGE 5
n
The ST 5026 controls six stages of constant-speed fans (Stages 1 - 6) and
two optional stages of constant-speed fans (Stages 7 & 8).
1.5 oF
When the temperature curve is activated, the current temperature set
point and day number can be viewed at any time. The current day number can also be adjusted in order to move forward or backward on the
temperature curve.
COOLING OPERATION
1.5 oF
Viewing Current Set Point and Day Number
STAGE 8
3
VENTILATION SETTINGS
1.5 oF
ST 5026
QM 1339.rev.03
21
ST 5026
ST 5026
If room temperature rises:
• When room temperature < Set Point + Timer Temp. Range, stage
1 fans run according to the minimum ventilation cycle.
• At Set Point + Timer Temp. Range: stage 1 fans run continuously.
• At Stage 2 Starting Temp: stage 2 fans start running.
MINIMUM VENTILATION CYCLE
When the room temperature is below the set point, the Stage 1 fans operate
according to the minimum ventilation cycle. Running the fans even though
ventilation is not required for a cooling purpose is useful to reduce humidity
levels and supply oxygen to the room. It also prevents the fans from freezing
in winter.
• At Stage 3 Starting Temp: stage 3 fans start running.
• At Stage 4 Starting Temp: stage 4 fans start running.
TIME ON
STAGE 1
STAGE 1 FANS
• At Stage 5 Starting Temp: stage 5 fans start running.
• At Stage 6 Starting Temp: stage 6 fans start running.
• At Stage 7 Starting Temp: stage 7 fans start running.
• At Stage 8 Starting Temp: stage 8 fans start running.
OFF
TIME OFF
STAGE 1
Stage 1 fans run during time on. The Stage 1 Pilot Light turns on. During
time off, the Stage 1 fans do not run. The Stage 1 Pilot Light turns off.
If the room temperature falls:
• At Stage 8 Starting Temp - 1.5oF: stage 8 fans return to a stop.
• At Stage 7 Starting Temp - 1.5oF: stage 7 fans return to a stop.
• At Stage 6 Starting Temp - 1.5oF: stage 6 fans return to a stop.
• At Stage 5 Starting Temp - 1.5oF: stage 5 fans return to a stop.
• At Stage 4 Starting Temp - 1.5oF: stage 4 fans return to a stop.
Minimum Ventilation Cycle Settings
1. To run the fans continuously at minimum speed, set time off to zero and
time on to any value other than zero.
2. To stop the fans, set time on to zero and time off to any value.
3. To run the fans intermittently, set time on to the desired running time
and time off to the desired off time.
• At Stage 3 Starting Temp - 1.5oF: stage 3 fans return to a stop.
• At Stage 2 Starting Temp - 1.5oF: stage 2 fans return to a stop.
• At Set Point + Timer Temp. Range - 1.5oF: Stage 1 fans start to run
according to the minimum ventilation cycle.
22 QM 1339.rev.03
QM 1339.rev.03
23
ST 5026
ST 5026
RAMPING OPTION
Option 2: Without Ramping
The ramping option allows the user to smooth the transition between minimum cycle and full operation of stage 1 fans, i.e. in the temperature interval between the set point and the set point + timer temp. range.
Option 1: With Ramping
Running
Time
1.5 oF
TIME ON =
CYCLE TIME
A
Running
Time
B
C
TIME ON
0.3oF
TIME ON =
CYCLE TIME
A
MINIMUM
VENTILATION
CYCLE
SET POINT
Indoor Temperature
TIMER TEMP.
RANGE
STAGE 1
SET POINT
Indoor Temperature
TIMER TEMP.
RANGE
STAGE 1
TIME ON
MINIMUM
VENTILATION
CYCLE
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
12345678901234567890123456
This option is activated by setting internal switch # 5 to ON. At room
temperatures at or below the set point, the controller operates the Stage 1
fans according to the minimum ventilation cycle.
This option is activated by setting internal switch # 5 to OFF. When the
temperature is less than the set point + timer temp. range, Stage 1 fans run
according to the minimum cycle (see above). When the room temperature
reaches point A, stage 1 fans run continuously with no transition.
When the temperature decreases 1.5oF below point A, Stage 1 fans start
operating according to the minimum ventilation cycle.
If the room temperature rises above the set point, a new TIME ON is calculated periodically as the temperature increases to allow a smooth progression (from point A to point B) up to full operation of the fans when the timer
temp. range is reached.
If the room temperature decreases 0.3oF below the set point + timer temp.
range, the TIME ON value of the minimum ventilation cycle decreases gradually from a value equal to the total cycle time (point C) to the value defined
by the parameter settings (TIMER STAGE 1 - TIME ON).
24 QM 1339.rev.03
QM 1339.rev.03
25
ST 5026
ST 5026
1
Viewing and Adjusting Stage 1 Time On
n
Set the selection knob to STAGE 1
— TIME ON. The current time on
for Stage 1 flashes on the display,
alternating with the letters "On".
n
Use the adjustment knob to adjust
time on to the desired value.
n
If the ramping option has been enabled, the actual time on value may
differ from the user-defined time on. To view the time on value actually
used by the controller, press the push-button. The actual time on value
is displayed for 1 minute, alternating with the letters "CAL". The display
then returns to the user-defined value.
Time on can be adjusted between 0 and 900 seconds, in increments of 15
seconds.
2
n
MINIMUM VENTILATION COMPENSATION
The ST 5026 has the capability of automatically adjusting the running time
of the minimum ventilation fans as a function of outside temperature. As
the weather gets colder, the on time is decreased gradually to compensate
for the change. This can help reduce costs by reducing the ventilation when
it is not required. A curve is used to calculate the required compensation
as a percentage of current on time (see following page). Only the running
time is adjusted; the total cycle time remains unchanged. Note that internal
switch # 6 must be set to ON for this feature to work.
Examples of Ventilation Compensations
Temperature > 50 oF
Compensation = 100%
TIME ON
ON
○
OFF
○
○
○
○
○
Viewing and Adjusting Stage 1 Cycle Time / Time Off
Set the selection knob to STAGE 1 — CYCLE TIME. The current cycle
time for the Stage 1 timer flashes on the display, alternating with the
letters "CyC".
CYCLE TIME
Outdoor Temperature = 25 oF
Compensation = 66.5%
ON
n
Use the adjustment knob to adjust cycle time on to the desired value.
n
If you wish to view time off, press the push-button. This value may not
simply be the difference between the cycle time and time on if the
ramping option has been enabled. The time off value actually used by
the controller is displayed for 1 minute. The display then returns to the
cycle time.
The cycle time can be adjusted between 0 and 900 seconds, in increments of
15 seconds. The counter starts at the current time on value.
26 QM 1339.rev.03
OFF
○
○
○
○
TIME ON
○
○
CYCLE TIME
In the first example given on the following page, compensation is not needed
when the outside temperature is greater than 50 oF. The fans operate
according to the full running time defined by the parameter settings. In the
second example, the running time is decreased to 66.5% of full running
time to compensate for the colder outdoor temperature. Cycle time remains unchanged.
QM 1339.rev.03
27
ST 5026
ST 5026
FIGURE 2: COMPENSATION CURVE
ii) The controller recalculates the compensation factor at the end of the
time on portion of each timer cycle.
Minimum Ventilation Compensation
100
VENTILATION SETTINGS
Ventilation Compensation (%)
90
80
1
70
The stage 1 timer temperature range is the temperature difference between
the set point and the temperature at which stage 1 fans run continuously.
When this value is adjusted, all the starting values for consecutive stages are
adjusted by the same amount. The timer temperature range can go from 0.5°F
to 20.0°F (0.3°C and 11.1°C).
60
50
40
30
20
n
Set the selection knob to STAGE
1 — TIMER TEMP. RANGE. The
current timer temperature range
flashes on the display.
n
Use the adjustment knob to adjust
the range to the desired value.
10
0
-20 -15 -10 -5
0
6
10 15 20 25 30 36 40 45 50 70
Outside Temperature (F)
1
Adjusting Stage 1 Timer Temperature Range
Activating / Deactivating Compensation Factor
n
Set the selection knob to OUTSIDE — TEMP./COMPENSATION. The
current outside temperature is displayed.
n
Press the push-button. The status of the compensation factor is
displayed, i.e. ON / OFF. Use the adjustment knob to set the status to
the desired value. After ten seconds, the display returns to the outside
temperature value.
NOTES:
i) When the compensation factor is activated, the lowest time on value
allowed after zero is 30 seconds.
28 QM 1339.rev.03
2
Adjusting Stages 2 - 8 Starting Temperatures
The starting temperature for a given stage is the temperature at which that
stage starts. The hysteresis is fixed at 1.5oF and determines when the fans
stop operating. When this value is adjusted, all the starting values for
consecutive stages are adjusted by the same amount. The difference
between between two consecutive starting temperatures can go from 0.5°F
to 20.0°F (0.3°C and 11.1°C).
n
Set the selection knob to the desired stage position. If the stage is
combined with other stages, the starting temperature of the first stage
is displayed, alternating with the letters "st.x" where x is the number of
the stage. Otherwise, the starting temperature of the chosen stage
flashes on the display.
QM 1339.rev.03
29
ST 5026
ST 5026
n
If the starting temperature displayed is the one to be adjusted, use the
adjustment knob to set the temperature to the desired value. Othervise,
press the push-button until the starting temperature of the desired stage
is displayed. Then, use the adjustment knob to set the temperature to
the desired value.
Mist units turn on
in timer mode
Mist units turn off
1.5oF
Mist
MIST COOLING
The last cooling stage can be configured as a mist stage. The number of
OFF
heating stages determines which stage this is.
Set Point
NUMBER OF HEATING STAGES
0
1
2
MIST STAGE
8
7
6
To access the parameters, position the selector switch at the starting
temperature of the mist stage. The parameter settings are as follows:
Starting Temperature (oF or oC) - The mist starting temperature is the
temperature at which the mist units turn on (see the diagram below). The
starting temperature minus 1.5 oF is the temperature at which the mist units
turn off.
Time on (minutes) - The mist units operate according to a timer cycle.The
time on is the running time of the mist units.
Time off (minutes) - The time off is the off time of the mist units. Note that
time off must be non-zero in order for the controller to recognize the stage as
a mist stage.
1
Starting
Temperature
Room
Temperature
Adjusting the Mist Starting Temperature
The difference between the mist starting temperature and the starting
temperature of the preceding stage can go from 0.5°F to 20.0°F (0.3°C and
11.1°C).
n Set the parameter selection knob to the starting temperature setting
of the mist stage. The current starting temperature appears flashing
on the display.
n Using the adjustment knob, set the starting temperature to the desired
value.
2
Adjusting the Mist Timer Settings
TIME ON
ON
Time on and Time off can be adjusted between 0 and 60 minutes, in
increments of 1 minute.
OFF
n Set the parameter selection knob to the starting temperature
TIME OFF
30 QM 1339.rev.03
setting of the mist stage. The current starting temperature appears
flashing on the display.
QM 1339.rev.03
31
ST 5026
n Push the push-button. The word "On" flashes on the display, alternat-
HEATER SETTINGS
PRINCIPLE OF OPERATION
ing with the current time on value.
n Turn the adjustment knob to adjust the time on to the desired value (in
The graph below explains the operation of the heaters using sample values.
minutes).
n Press the push-button once again. The word "Off" flashes on the
Heating
n Turn the adjustment knob to adjust the time off to the desired value (in
minutes). Note that time off must be non-zero in order for the controller to operate the stage as a mist stage.
Heater B OFF
Heater B ON
display, alternating with the current time off value.
Heater B
Heater A ON
Heater A
Heater A OFF
HEATER
B / ON
TEMP.
= 70oF
HEATER
A / ON
TEMP.
= 72oF
OFF
TEMP.
= 74oF
Set Point
= 75oF
Room
Temperature
If the room temperature rises:
- at 72oF: Heater B turns off.
- at 74oF: Heater A turns off.
If the room temperature falls:
- at 72oF: Heater A turns on.
- at 70oF: Heater B turns on.
32 QM 1339.rev.03
QM 1339.rev.03
33
ST 5026
1
Adjusting the Heater Off Temperature
The heater off temperature can provide substantial energy savings if correctly adjusted according to the outside temperature. It is the temperature
at which the heating units turn off (see diagram above). The off temperature is bounded above by the set point plus 10oF and below by the set point
— 20oF.
n
n
2
Set selection knob to HEATER
A/B — OFF TEMP. The current
off temperature flashes on the
display.
Use the adjustment knob to adjust the off temperature to the
desired value.
Adjusting the Heater Starting Temperatures
The starting temperature is the temperature at which the heater turns on.
The Heater A starting temperature is bounded above by the off temperature
— 0.5oF and below by the off temperature — 20oF. The Heater B starting
temperature is bounded above by the Heater A starting temperature —
0.5oF and below by the Heater A starting temperature — 20oF.
n
Set the selection knob to HEATER A — START TEMP. or HEATER
B — START TEMP. The current starting temperature for the heater
selected flashes on the display.
n
Use the adjustment knob to adjust the starting temperature to the
desired value.
34 QM 1339.rev.03
ALARM SETTINGS
The controller sets off an alarm in the case of a power failure, a fault in the
supply circuit or a high or low temperature. Temperature alarms are defined according to the set point as shown in the diagram below.
Room
Temperature
High Temperature Alarm
High Alarm Offset
Set Point
Low Alarm Offset
Time
The situation changes for high temperature alarms, however, when the outside
temperature is greater than the set point. In this case, the set point is
replaced by the outside temperature as the reference point. This means an
alarm is set off when the indoor temperature reaches Outside Temperature
+ High Alarm Offset. Internal switch # 7 must be set to ON to use this
feature. A third parameter, called the critical high temperature, is defined to
continue monitoring the indoor temperature for high temperatures. When
the indoor temperature reaches the critical high temperature (defined as
an absolute value), an alarm is set off.
QM 1339.rev.03
35
ST 5026
TROUBLESHOOTING GUIDE
Adjusting the Alarm Settings
PROBLEM
The high and low alarm settings are specified as an offset. The high and low
alarm offsets range from 0.5oF to 40oF. The critical temperature ranges from
-40.0°F to 120.0°F (-40.0°C to 48.9°C).
n
n
Correct the problem and reset
the circuit breaker.
The wiring is incorrect.
Correct the wiring.
The voltage selector
switch is in the
wrong position.
Set the switch to the correct
position.
The display board
interconnect cable is
not properly plugged
into the power supply
board.
Be sure the cable is firmly
plugged in.
The display
shows "P" when
the parameter
selection knob is
set to OUTSIDE
SETTINGS.
The outside probe
is connected improperly.
Correct the outside probe
connection.
The outside probe is
defective.
Refer to "defective probes"
The display
shows "P" when
the parameter
selection knob is
set to ROOM.
A room probe is
connected improperly.
Correct the room probe connection.
A room probe is
defective.
Refer to "defective probes"
Use the adjustment knob to set
the low alarm offset to the desired
value.
Press the push-button. The current high alarm offset is displayed,
alternating with the letters "HI" and "OFT".
n
Use the adjustment knob to set the high alarm offset to the desired
value.
n
Press the push-button. The current critical high temperature is displayed, alternating with the letters "ABS".
n
Use the adjustment knob to set the critical high temperature to the
desired value.
36 QM 1339.rev.03
SOLUTION
The circuit breaker at
the service panel is
off or tripped.
There is no
display.
Set the selection knob to ALARM
— LO / HIGH. The current low
alarm offset is displayed, alternating with the letters "LO" and
"OFT".
n
CAUSE
QM 1339.rev.03
37
ST 5026
ST 5026
PROBLEM
CAUSE
SOLUTION
The defective
probe pilot light
is on.
A room or outside
probe is defective.
Refer to "defective probes"
The display
shows sudden
variations in the
room or outside
temperature.
A variation in resistance is induced on a
probe.
Be sure the probes are dry.
Locate them away from drafts
and sources of radiant heating.
Be sure the outside probe is
installed correctly. Refer to
"Installing the outside probe"
There is electrical
noise near a probe
cable.
Stage 1 fans do
not stop
running when
the controller
is operating in
minimum
ventilation
cycle.
38 QM 1339.rev.03
Isolate the probe cables from all
high voltage sources. Do not
route probe cables and other
power cables through the same
electrical knockout. Do not run
probe cables next to other
power cables. When crossing
other power cables, cross at
90°.
Time off is set to
zero.
Set time off to a value other than
zero.
The wiring is incorrect.
Correct the wiring. In particular,
make sure two different lines
are connected to each motor:
line L1 modulated by the
controller should be combined
with another line (N for 115V or
L2 for 230V) to activate the
motor. Also, be sure the stage 1
COMMON is supplied by line L1.
PROBLEM
CAUSE
The mist is not
operating as
desired.
The mist time on and
time off were incorrectly adjusted.
The mist time on and time off
are in minutes. Adjust the mist
time on and time off correctly.
The cooling fans
are not running.
The wiring is incorrect.
Correct the wiring. Be sure
two different lines are connected
to each fan motor or heater: the
controller's output line L1 should
be combined with another line
(N for 115V or L2 for 230V) to
activate the fan motor or heater.
Also, be sure the stage's
COMMON is supplied by line L1.
The stage's fuse is
open.
Replace the fuse.
The display board
interconnect cable is
not properly plugged
into the power supply
board.
Be sure the cable is firmly
plugged in.
The fan motor or
heater is defective.
Check if the motor or heater is
defective by connecting it to an
alternate power supply. If it still
is not operating, replace the
motor or heater.
The controller is
defective.
Listen to see if there is a clicking
sound when the stage or heater
pilot light turns on. If there is no
clicking sound, contact your
distributor to repair the
controller.
or
The heaters are
not turning on.
SOLUTION
QM 1339.rev.03
39
TECHNICAL SPECIFICATIONS
FACTORY SETTINGS
Supply: - 115/230 VAC (-18%, +8%), 50/60 Hz, overload and overvoltage
protection fuse F10-1A fast blow.
- 12 VDC for AC back-up supply; can activate stages 1 through 8
if supplied with DC back-up voltage.
Stage 1: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F1-10A slow blow.
Stage 2: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F2-10A slow blow.
P A R A M E T E R
Te m p e r a t u r e
S et P oi nt
Ti me
Stage
1
C ycle
On
F A C T O R Y
S E T T I N G
Ti m e r Te m p .
Range
-40
(-40
7 5 oF ( 2 3 . 9 oC )
15
Ti me
R A N G E O F
V A L U E S
300
seconds
seconds
0
to
to
99.9
37.7
o
o
F
C )
to 900 seconds by
i ncrements of 15
seconds
3 oF ( 1 . 7 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC )
Stage
2
Starti ng
Te m p .
8 0 oF ( 2 6 . 7 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
Stage 1 conti nuous
Stage 3: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F3-10A slow blow.
Stage
3
Starti ng
Te m p .
8 2 oF ( 2 7 . 8 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 2 S t a r t i n g Te m p .
Stage 4: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F4-10A slow blow.
Stage
4
Starti ng
Te m p .
8 4 oF ( 2 8 . 9 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 3 S t a r t i n g Te m p .
Stage
5
Starti ng
Te m p .
8 6 oF ( 3 0 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 4 S t a r t i n g Te m p .
Stage
6
Starti ng
Te m p .
8 8 oF ( 3 1 . 1 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 5 S t a r t i n g Te m p .
Stage
7
Starti ng
Te m p .
9 0 oF ( 3 2 . 2 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 6 S t a r t i n g Te m p .
Stage
8
Starti ng
Te m p .
9 1 oF ( 3 2 . 8 oC )
0 . 5 t o 2 0 oF
( 0 . 3 t o 1 1 . 1 oC ) f r o m
S t a g e 7 S t a r t i n g Te m p .
Stage 5: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F5-10A slow blow.
Stage 6: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, fuse F6-10A slow blow.
Stage 7: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, heating or cooling, fuse F7-10A slow blow.
Stage 8: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 6A FAN,10A
RES, heating or cooling, fuse F8-10A slow blow.
Alarm: ON-OFF output, 115/230 VAC, 50/60 Hz, 30VDC, 3A, fuse F9-3A
slow blow.
Probes: Low voltage ( < 5V), isolated from the supply. Operating range:
-40.0° to 120.0°F (-40.0° to 48.9°C). Accuracy: 1.8oF (1oC) between 41o and
95oF (5o and 35oC).
Starti ng
Te m p e r a t u r e
40 QM 1339.rev.03
2 0 oF
1 oC ) f r o m
stage's
Te m p .
Mi st
Heater
Enclosure: ABS, moisture and dust-tight.
The room temperature where the controller is located MUST
ALWAYS REMAIN BETWEEN 32o AND 104oF (0o AND 40oC).
9 1 oF ( 3 2 . 8 oC )
0.5 to
(0.3 to 11.
previ ous
Starti ng
A larm
Ti me
On
Ti me
Off
1
0
mi nute
mi nutes
O f f Te m p e r a t u r e
7 4 . 5 oF ( 2 3 . 6 oC )
Low
Te m p e r a t u r e
6 5 oF ( 1 8 . 3 oC )
Hi gh
Te m p e r a t u r e
8 7 oF ( 3 0 . 6 oC )
C ri ti cal
Te m p e r a t u r e
9 5 oF ( 3 5 oC )
0 to 60 mi nutes by
i ncrements of 1 mi nute
- 2 0 t o 1 0 oF
( - 1 1 . 1 t o 5 . 6 oC ) f r o m
S et P oi nt
(0.3
0 . 5 t o 4 0 oF
t o 2 2 . 2 oC ) f r o m
S et P oi nt
-40 to 120.0
(-40 to 48.9
F
C )
o
o
QM 1339.rev.03
41
ST 5026
NOTES:
i) These initial parameter settings will not be retained in the controller's
memory. Each new setting will replace the preceding one.
ii) If the power supply is cut off, the last parameter settings will be
retained in memory until the power is restored.
42 QM 1339.rev.03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement