ICPDAS I-8000 I-8094, I-8094F Motion Control Module User Manual
Below you will find brief information for Motion Control Module I-8000 I-8094, Motion Control Module I-8000 I-8094F. This manual explains the I-8094's macro functions (MF), which simplify programming for users developing applications to automate equipment. The DLL file provides a set of functions that can be used on different platforms such as eVC++, VB.net, and C#.net with different OS systems (MiniOS7 / WinCE / Linux). The functions are organized in six chapters, starting with basic settings for each module, then moving on to reading and setting registers. The manual also provides details on how to use the automatic homing feature, general motion control functions, and advanced features like continuous interpolation.
Advertisement
Advertisement
4-axis Motion Control Module
User Manual
(I-8094 and I-8094F)
(Version 2.5)
Macro Function Library in C++ for
WinCon and I-8000 series PAC controllers
ICPDAS I-8094 Software User Manual
Warranty
All products manufactured by ICPDAS Inc. are warranted against defective materials for a period of one year from the date of delivery to the original purchaser.
Warning
ICPDAS Inc. assumes no liability for damages consequent to the use of this product. ICPDAS Inc. reserves the right to change this manual at any time without notice. The information furnished by ICPDAS Inc. is believed to be accurate and reliable. However, no responsibility is assumed by ICPDAS Inc. for its use, or for any infringements of patents or other rights of third parties resulting from its use.
Copyright
Copyright 1997-2009 by ICPDAS Inc., LTD. All rights reserved worldwide.
Trademark
The names used for identification only maybe registered trademarks of their respective companies.
License
The user can use, modify and backup this software on a single machine. The user may not reproduce, transfer or distribute this software, or any copy, in whole or in part.
ICPDAS I-8094 Software User Manual
INDEX
1 PREFACE ............................................................................ 6
2 BASIC SETTINGS.............................................................. 8
2.2 Registration of Modules and getting the LIB version ............................ 8
2.5 Setting the Maximum Speed ................................................................... 13
2.6 Setting the Active Level of the Hardware Limit Switches ................... 13
2.7 Setting the Motion Stop Method When Limit Switch Is Sensed ......... 15
2.8 Setting the Trigger Level of the NHOME Sensor ................................. 15
2.9 Setting Trigger Level of the Home sensor ............................................. 16
2.10 Setting and Clearing the Software Limits ........................................... 16
2.11 Setting the Encoder Related Parameters ............................................. 18
2.12 Setting the Servo Driver (ON/OFF) ..................................................... 18
2.13 Setting the SERVO ALARM Function ................................................ 20
2.14 Setting the Active Level of the In-Position Signals ............................. 20
2.15 Setting the Time Constant of the Digital Filter................................... 22
2.16 Position Counter Variable Ring............................................................ 23
2.17 Triangle prevention of fixed pulse driving .......................................... 25
2.18.4 Disabling the External Signal Input Functions.............................................30
2.19 Configure hardware with pre-defined configuration file................... 31
3 READING AND SETTING THE REGISTERS............. 32
3.1 Setting and Reading the Command Position (LP)................................ 32
3.2 Setting and Reading the Encoder Counter............................................ 33
3.4 Reading the Current Acceleration.......................................................... 34
3.6 Reading and Clearing the ERROR Status ............................................ 37
4 FRNET FUNCTIONS (FOR I8094F ONLY).................. 39
ICPDAS I-8094 Software User Manual
5 AUTO HOMING ............................................................... 41
5.2 Using an Limit Switch as the HOME sensor......................................... 43
5.4 Starting the Homing Sequence ............................................................... 49
5.5 Waiting for the Homing sequence to be Completed ............................. 49
6 GENERAL MOTION CONTROL.................................. 50
6.1 Independent Axis Motion Control.......................................................... 50
6.1.8 Setting the Value of the Remaining Offset Pulses .........................................59
6.2.2 Setting the Speed and Acc/Dec Mode for Interpolation ................................63
6.2.9 Setting the Number of the Remaining Offset Pulses .....................................73
6.2.13 2-Axis Circular Interpolation Motion (a Complete Circle) ...........................78
6.3.4 Set the PRESET data for synchronous action................................................86
ICPDAS I-8094 Software User Manual
6.4.4 Mixed Linear and Circular 2-axis motions in Continuous Interpolation ......93
6.4.5 Multi-Segment Continuous Interpolation (Using Array) ................................96
6.6.2 Release the Holding Status, and Start the Driving.......................................108
ICPDAS I-8094 Software User Manual
1 Preface
1.1 Introduction
This manual provides complete and detailed description of i8094 functions for
users to develop programs for their control of automatic equipments. Many examples are included in this manual for reference to write efficient application programs.
This manual includes six chapters and two appendices. This chapter gives a
brief description of this manual. Chapter 2 to 6 is the explanations of macro functions (MF).
The functions defined in DLL file are explained here. This DLL can be used on
different developing software platforms, such as eVC++, VB.net, and C#.net, and different OS systems ( MiniOS7 / WinCE / Linux).
1.2 Macro functions
Macro functions provide a set of much easy-to-use functions that simplify the
programming for users. Some necessary settings, such as speed range and deceleration point, are calculated inside those functions to ease the loading of users on having to understand the motion chip. Some useful costumed functions are provided for users to develop applications efficiently.
ICPDAS I-8094 Software User Manual
1.3 Funciton description
All functions are listed in following form:
z Function_name (parameter1, parameter2, …)
Description: Explanation of this function.
Parameters: Definitions of the parameters and how to use them.
Return: The return value of this function.
Example: Simple example program in C++.
Remark: Comments.
ICPDAS I-8094 Software User Manual
2 Basic Settings
2.1 Code numbers for axes
The axis assignments follow the definitions listed below: X=1, Y=2, Z=4, and
U=8. If X and Y axes are assigned simultaneously, then the code number is 3. In a similar way, AXIS_YZ = 2+4 =0x6; and AXIS_XYZU = 1+2+4+8 = 0xf. An assignment for either single axis or multiple axes at the same time is possible.
Available axis code numbers are listed below. The type of the axis argument used in the functions is defined as WORD.
Table 2-1 Axis assignments and their corresponding codes
Axis X Y Z U XY XZ XU YZ
Code
0x1 0x2 0x4 0x8 0x3 0x5 0x9 0x6
Name
AXIS_X AXIS_Y AXIS_Z AXIS_U AXIS_XY AXIS_XZ AXIS_XU
Axis
YU ZU XYZ XYU XZU YZU
Code
0xa 0xc 0x7 0xb 0xd 0xe
XYZU
0xf
Name
AXIS_YU AXIS_ZU AXIS_XYZ AXIS_XYU AXIS_XZU AXIS_YZU AXIS_XYZU
2.2 Registration of Modules and getting the LIB version
z
BYTE i8094MF_REGISTRATION( BYTE cardNo, BYTE slot)
Description:
This function registers a module that is installed in slot number, slot, by assigning a card number. Registration must be performed for each I-8094 motion control module before other functions are called.
After registration, each module can be identified by its corresponding module number.
Parameters:
cardNo: Module number for I-8000: 0~7
for WinCon-8000: 1~7
Return:
YES Normal
NO Abnormal
ICPDAS I-8094 Software User Manual
Example:
//================= for WinCon-8000 ==================
//set each module number the same as the slot number, respectively.
//(slot1 ~ slot7)
BYTE cardNo;
BYTE slot; int Found = 0; for (slot = 1; slot < 8; slot++)
{ cardNo = slot; if (i8094MF_REGISTRATION(cardNo, slot) == YES)
{ //slot number begins from 1.
//if a module is found, then it is registered as its slot number. i8094MF_RESET_CARD(cardNo);
Found++;
}
} if (Found == 0)
{
//if Wincon cannot find any I-8094 module,
//please add codes to handle the exception here. return ;
}
//=================== for I-8000 ===================
//set the module number the same as the slot number, respectively.
//(slot1 ~ slot7)
BYTE cardNo;
BYTE slot; int Found = 0; for (slot = 0; slot < 8; slot++)
{ cardNo = slot + 1;
//slot number begins from 0, but module number begin from 1.
if (i8094MF_REGISTRATION(cardNo, slot) == YES)
{
//if a module is found, then it is registered by giving a number. i8094MF_RESET_CARD(cardNo);
Found++;
}
} if (Found == 0)
{
//if Wincon cannot find any I-8094 module,
//please add codes to handle the exception here. return ;
ICPDAS I-8094 Software User Manual
}
z
WORD i8094MF_GET_VERSION( void )
Description:
Read the version of current i8094 library.
Parameters:
cardNo: Module number
Return:
Version code: including information of the year and the month: 0x0000 ~ 0x9999
Example:
WORD VER_No;
VER_No = i8094MF_GET_VERSION();
//Read the version code of i8094.dll
Remark:
If the return value is 0x0607
06 : the year is 2006
07: the month is July.
ICPDAS I-8094 Software User Manual
2.3 Resetting Module
z
void i8094MF_RESET_CARD( BYTE
cardNo)
Description:
This function resets module using a software command.
Parameters:
cardNo: Module number
Return:
None
Example: i8094MF_RESET_CARD(1);
//Reset module 1.
2.4 Pulse Output Mode Setting
z
void i8094MF_SET_PULSE_MODE( BYTE cardNo, WORD axis, BYTE nMode)
Description:
This function sets the pulse output mode as either CW/CCW or PULSE/DIR for the assigned axes and their direction definition.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nMode: Assigned mode (Please refer to Table 2-2)
Return:
None
ICPDAS I-8094 Software User Manual
Example: i8094_SET_PULSE_MODE(1, AXIS_XYZ, 2);
//set the pulse mode of X, Y, and Z axes as mode 2 i8094_SET_PULSE_MODE(1, AXIS_U, 3);
//set the pulse mode of U axis as mode 3
Table 2-2 A List of pulse output modes mode
Pulse output signals nPP nPM
CW / CCW
0
1
CW (rising edge)
CW (falling edge)
PULSE / DIR
2
3
4
5
PULSE (rising edge)
PULSE (falling edge)
PULSE (rising edge)
PULSE (falling edge)
CCW (rising edge)
CCW (falling edge)
DIR
(LOW:+dir/ HIGH:-dir)
DIR
(LOW:+dir/ HIGH:-dir)
DIR
(HIGH:+dir/ LOW:-dir)
DIR
(HIGH:+dir/ LOW:-dir)
ICPDAS I-8094 Software User Manual
2.5 Setting the Maximum Speed
z
void i8094MF_SET_MAX_V( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the maximum rate for the output pulses (speed). A larger value will cause a rougher resolution. For example, when the maximum speed is set as 8000 PPS, the resolution is 1 PPS; when the maximum speed is set as 16000 PPS, the resolution is 2 PPS; when maximum speed is set as 80000 PPS, the resolution is 10 PPS, etc. The maximum value is 4,000,000 PPS, which means the resolution of speed will be 500 PPS. This function change the resolution of speed to reach the desired maximum speed. Since the scale in hardware is changed, other parameters will be influenced too, such as the starting speed, the acceleration, and the jerk. It is recommended to set the maximum speed value as a integral multiplier of 8000.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The assigned maximum speed of each axis when the controller performs an interpolation motion. However, setting the value of axis 1 is enough. For axis 1, the maximum value is 4,000,000 PPS.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_XY, 200000L);
//The maximum speed for the X and Y axes of module 1 is 200KPPS.
//The resolution of the speed will be 200000/8000 = 25 PPS.
2.6 Setting the Active Level of the Hardware Limit Switches
z
void i8094MF_SET_HLMT( BYTE cardNo, WORD axis, BYTE nFLEdge,
BYTE nRLEdge)
Description:
This function sets the active logic level of the hardware limit switch inputs.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
ICPDAS I-8094 Software User Manual
nFLEdge: Active level setting for the forward limit switch.
0 = low active; 1 = high active
nRLEdge: Active level setting for the reverse limit switch.
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_HLMT(1, AXIS_XYZU, 0, 0);
//set all the trigger levels as low-active for all limit switches
//on module 1.
ICPDAS I-8094 Software User Manual
2.7 Setting the Motion Stop Method When Limit Switch Is
Sensed
z
void i8094MF_LIMITSTOP_MODE ( BYTE cardNo, WORD axis, BYTE nMode)
Description:
This function sets the motion stop mode of the axes when the corresponding limit switches are detected.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nMode: 0: stop immediately; 1: decelerating to stop
Return:
None
Example: i8094MF_LIMITSTOP_MODE(1, AXIS_X, 0);
//set X axis to stop immediately if any limit switch on X axis is triggered.
2.8 Setting the Trigger Level of the NHOME Sensor
z
void i8094MF_SET_NHOME( BYTE cardNo, WORD axis, BYTE nNHEdge)
Description:
This function sets the trigger level of the near home sensor (NHOME).
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nNHEdge: Active level setting for the near home sensor.
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_NHOME(1, AXIS_XY, 0);
//set the trigger level of NHOME of X and Y axes on module 1 to be active low.
ICPDAS I-8094 Software User Manual
2.9 Setting Trigger Level of the Home sensor
z
void i8094MF_SET_HOME_EDGE( BYTE cardNo, WORD axis, BYTE nHEdge)
Description:
This function sets the trigger level of the home sensor (HOME).
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nHEdge:
Active level setting for the home sensor.
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_HOME_EDGE(1, AXIS_XYZU, 1);
//set the trigger level as high active for all home sensors on module 1.
2.10 Setting and Clearing the Software Limits
z
void i8094MF_SET_SLMT( BYTE cardNo, WORD axis, long dwFL, long dwRL,
BYTE nType)
Description:
This function sets the software limits.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
dwFL: Value of the forward software limit
(-2,147,483,648 ~ +2,147,483,647)
dwRL: Value of the reverse software limit
(-2,147,483,648 ~ +2,147,483,647)
nType: Position counter to be compared:
0 = logical position counter (LP), i.e., the command position
1 = encoder position counter (EP), i.e., the real position
Return:
None
ICPDAS I-8094 Software User Manual
Example: i8094MF_SET_SLMT(1, AXIS_XYZU, 20000, -3000, 0);
//set the forward software limit as 20000 and the reverse
//software limit as -3000 for all axes on module 1.
z
void i8094MF_CLEAR_SLMT( BYTE cardNo, WORD axis)
Description:
This function clears the software limits.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_CLEAR_SLMT(1, AXIS_XYZU);
//clear the software limits for all axes on module 1.
ICPDAS I-8094 Software User Manual
2.11 Setting the Encoder Related Parameters
z
void i8094MF_SET_ENCODER( BYTE cardNo, WORD axis, BYTE nMode,
BYTE nDivision, BYTE nZEdge)
Description:
This function sets the encoder input related parameters.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nMode: Encoder input type: 0 = A quad B; 1 = up/down
nDivision: Division setting for A quad B input signals:
0 = 1/1
1 = 1/2
2 = 1/4
nZEdge: Sets the trigger level for the Z phase
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_ENCODER(1, AXIS_XYZU, 0, 0, 0);
//set the encoder input type as A quad B; the division is 1;
//and the Z phase is low active.
2.12 Setting the Servo Driver (ON/OFF)
z
void i8094_SERVO_ON( BYTE cardNo, WORD axis)
Description:
This function outputs a DO signal (ENABLE) to enable the motor driver.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example:
ICPDAS I-8094 Software User Manual
//enables all drivers on module 1.
z
void i8094_SERVO_OFF( BYTE cardNo, WORD axis)
Description:
This function outputs a DO signal (ENABLE) to disable the motor driver.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example:
//disables all drivers on module 1.
ICPDAS I-8094 Software User Manual
2.13 Setting the SERVO ALARM Function
z
void i8094MF_SET_ALARM( BYTE cardNo, WORD axis, BYTE nMode,
BYTE nAEdge)
Description:
This function sets the ALARM input signal related parameters.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nMode: Mode: 0 = disable ALARM function;
1 = enable ALARM function
nAEdge: Sets the trigger level
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_ALARM(1, AXIS_ZU, 1, 0);
//enable the ALARM for the Z and U axes on module 1 and set them
//as low-active.
2.14 Setting the Active Level of the In-Position Signals
z
void i8094MF_SET_INPOS( BYTE cardNo, WORD axis, BYTE nMode,
BYTE nIEdge)
Description:
This function sets the INPOS input signal related parameters.
Note: Sometimes, this signal is used to connect the SERVO READY input signal. Users should take care of what signal the daughter board is wired.
Parameters:
cardNo: Module number
ICPDAS I-8094 Software User Manual
axis: Axis or axes (Please refer to Table 2-1)
nMode: Mode: 0 = disable INPOS input;
1 = enable INPOS input
nlEdge: Set the trigger level
0 = low active; 1 = high active
Return:
None
Example: i8094MF_SET_INPOS(1, AXIS_X, 1, 0);
//enable the INPOS function of the X axis on module 1 and set it to be low-active.
Note: Please refer to the example shown in Fig. 2.12 for wiring of the general DI input.
ICPDAS I-8094 Software User Manual
2.15 Setting the Time Constant of the Digital Filter
z
void i8094MF_SET_FILTER( BYTE cardNo, WORD axis, WORD FEn, WORD FLn)
Description:
This function selects the axes and sets the time constant for digital filters of the input signals.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
FEn: Enabled . The sum of the code numbers ( 0~31) are used to select input signals. Please refer to the following table.
Code number Enabling filters
1 EMG, nLMTP, nLMTM, nIN0, nIN1
2 nIN2
8 nEXPP, nEXPM, EXPLSN
16 nIN3
FLn: Sets the filter time constant ( 0~7) as follows.
Code Removable max. noise width Input signal delay time
0 1.75
1 224
μ
SEC 2
μ
SEC
μ
SEC 256
μ
SEC
2 448
3 896
μ
SEC 512
μ
SEC
μ
SEC 1.024mSEC
4 1.792mSEC 2.048mSEC
5 3.584mSEC 4.096mSEC
6 7.168mSEC 8.192mSEC
7 14.336mSEC 16.384mSEC
Return:
None
Example: i8094MF_SET_FILTER(1, AXIS_XYZU, 21, 3);
//set the filter time constants of X, Y, Z, and U axes as 1.024mSEC.
//These filters include EMG, nLMTP, nLMTM, nIN0, nIN1, nINPOS, nALARM,
//and nIN3.
//(21 = 1+4+16) 1: EMG + nLMP + nLMPM + nIN0 + nIN1; nIN3.
Note: The default wiring design is: nIN0 is connected to the NEAR HOME
(NHOME) sensors; nIN1 is connected to the HOME sensors; and nIN2 is connected to the index of Encoder input (Z phase).
ICPDAS I-8094 Software User Manual
2.16 Position Counter Variable Ring
z
void i8094MF_VRING_ENABLE( BYTE cardNo, WORD axis, DWORD nVRing)
Description:
This function enables the linear counter of the assigned axes as variable ring counters.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nVRing: Maximum value of the ring counter
(1 ~ 0xffffffff)
Return:
None
Example: i8094MF_ VRING_ENABLE(1, AXIS_X, 9999);
//set the X axis of module 1 to be a ring counter. The encoder
//values will be 0 to 9999.
The encoder value is 0 to 9999. When the counter value reach 9999, an adding pulse will cause the counter to reset to 0. When the counter value is 0, a lessening pulse will let the counter set to 9999.
Max. ring encoder value = 9999
Note: 1. This function will set the LP and EP simultaneously.
2. If this function is enabled, the software limit function cannot be used.
ICPDAS I-8094 Software User Manual
z
void i8094MF_VRING_DISABLE( BYTE cardNo, WORD axis)
Description:
This function disables the variable ring counter function.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_ VRING_DISABLE(1, AXIS_X);
//disable the ring counter function for the X axis
//on module 1.
ICPDAS I-8094 Software User Manual
2.17 Triangle prevention of fixed pulse driving
z
void i8094MF_AVTRI_ENABLE ( BYTE cardNo, WORD axis)
Description:
This function prevents a triangle form in linear acceleration (T-curve) fixed pulse driving even if the number of output pulses is low.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_ AVTRI_ENABLE(1, AXIS_X);
//set the X axis of module 1 not to generate a triangle form in its speed profile.
z
void i8094MF_AVTRI_DISABLE ( BYTE cardNo, WORD axis)
Description:
This function disable the function that prevents a triangle form in linear acceleration fixed pulse driving.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_ AVTRI_DISABLE(1, AXIS_X);
//enable the X axis of module 1 to generate a triangle form in its
//speed profile if the pulse number for output is too low.
ICPDAS I-8094 Software User Manual
2.18 External Pulse Input
2.18.1 Handwheel (Manual Pulsar) Driving
z
void i8094MF_EXD_MP( BYTE cardNo, WORD axis, long data)
Description:
This function outputs pulses according to the input pulses from a handwheel.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1.)
The axis can be either X, Y, Z, or U.
data: Gain (a multiplier)
Return:
None
Example: i8094MF_EXD_MP(1, AXIS_X, 1);
//Each time the handwheel inputs a pulse to the X axis
//on module 1, the controller will output 1 pulses to the motor driver.
ICPDAS I-8094 Software User Manual
i8094MF_EXD_MP(1, AXIS_X, 2);
//Each time the handwheel inputs a pulse to the X axis
//on module 1, the controller will output 2 pulses to the motor driver.
ICPDAS I-8094 Software User Manual
2.18.2 Fixed Pulse Driving Mode
z
void i8094MF_EXD_FP( BYTE cardNo, WORD axis, long data)
Description:
This function outputs fixed pulses according to the trigger input (the falling edge of the nEXP+ signal) from a handwheel.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1.)
The axis can be either X, Y, Z, or U.
data: Number of fixed pulses.
Return:
None
Example: i8094MF_EXD_FP(1, AXIS_X, 5);
//Each time the controller detects a falling edge of an XEXP+
//signal, it will output 5 pulses to the X axis.
Example of fixed pulse driving using an external signal
ICPDAS I-8094 Software User Manual
2.18.3 Continuous Pulse Driving Mode
z
void i8094MF_EXD_CP( BYTE cardNo, WORD axis, long data)
Description:
The controller will continuously output pulses in positive direction if the falling edge of nEXP+ signal from a handwheel is detected. Conversely, it will continuously output pulses in negative direction if the falling edge of nEXP- signal is detected.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1.)
The axis can be either X, Y, Z, or U.
data: Pulse output speed in PPS
Return:
None
Example: i8094MF_EXD_CP(1, AXIS_X, 20);
//Each time the controller detects a falling edge of an XEXP+
//signal, it will continuously drive X axis at the speed of 20 PPS.
Continuous driving using an external signal
ICPDAS I-8094 Software User Manual
2.18.4 Disabling the External Signal Input Functions
z
void i8094MF_EXD_DISABLE( BYTE cardNo, WORD axis)
Description:
This function turns off the external input driving control functions.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1.)
The axis can be either X, Y, Z, or U.
Return:
None
Example: i8094MF_EXD_DISABLE(1, AXIS_X);
//disable the external input driving control function
//of X axis on module 1
ICPDAS I-8094 Software User Manual
2.19 Configure hardware with pre-defined configuration file
z
short i8094MF_ LOAD_CONFIG ( BYTE cardNo)
Description:
This function loads the pre-defined configuration file and set the target I8094 module automatically. The configuration file is generated by the PACEzGo.
Parameters:
cardNo: Module number
Return:
0: successfully
-1: cannot open the pre-defined configuration file.
Example: i8094MF_ LOAD_CONFIG
(1);
//load the configuration file and configure the module 1.
ICPDAS I-8094 Software User Manual
3 Reading and Setting the Registers
3.1 Setting and Reading the Command Position (LP)
z
void i8094MF_SET_LP( BYTE cardNo, WORD axis, long wdata)
Description:
This function sets the command position counter value (logical position counter, LP).
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
wdata: Position
(-2,147,483,648 ~ +2,147,483,647)
Return:
None
Example: i8094MF_SET_LP(1, AXIS_XYZU, 0);
//Set the LP for the X, Y, Z, and U axes of module 1 as 0,
//which means that all LP counters on module 1 will be cleared.
z
long i8094MF_GET_LP( BYTE cardNo, WORD axis)
Description:
This function reads the command position counter value (logical position counter, LP).
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
The current LP value (-2,147,483,648 ~ +2,147,483,647)
Example: long X_LP;
X_LP = i8094MF_GET_LP(1, AXIS_X);
//Reads the LP value of the X axis on module 1.
ICPDAS I-8094 Software User Manual
3.2 Setting and Reading the Encoder Counter
z
void i8094MF_SET_EP( BYTE cardNo, WORD axis, long wdata)
Description:
This function sets the encoder position counter value (real position counter, or
EP).
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
wdata: Position
(-2,147,483,648 ~ +2,147,483,647)
Return:
None
Example: i8094MF_SET_EP(1, AXIS_XYZU, 0);
//Set the EP for the X, Y, Z, and U axes of module 1 as 0.
//This command clears all EP counters on module 1.
z
long i8094MF_GET_EP( BYTE cardNo, WORD axis)
Description:
This function reads the encoder position counter value (EP).
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
Current EP value (-2,147,483,648 ~ +2,147,483,647)
Example: long X_EP;
X_EP = i8094MF_GET_EP(1, AXIS_X);
//reads the encoder value (EP) of the X axis on module 1.
ICPDAS I-8094 Software User Manual
3.3 Reading the Current Velocity
z
DWORD i8094MF_GET_CV( BYTE cardNo, WORD axis)
Description:
This function reads the current velocity value.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
Current speed (in PPS)
Example:
DWORD dwdata; dwdata = i8094MF_GET_CV(1, AXIS_X);
//reads the current velocity of the X axis on module 1.
3.4 Reading the Current Acceleration
z
DWORD i8094MF_GET_CA( BYTE cardNo, WORD axis)
Description:
This function reads the current acceleration value.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
Current acceleration (in PPS/Sec)
Example:
DWORD dwdata; dwdata = i8094MF_GET_CA(1, AXIS_X);
//reads the current acceleration value of the X axis on module 1.
ICPDAS I-8094 Software User Manual
3.5 Reading the DI Status
z
BYTE i8094MF_GET_DI( BYTE cardNo, WORD axis, WORD nType)
Description:
This function reads the digital input (DI) status.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
nType:
0
Æ DRIVING
(Check whether the axis is driving or not.)
1
Æ LIMIT+
(Check whether the limit+ is engaged or not.)
2
Æ
(Check
3
Æ EMERGENCY (Check whether EMG signal is on or not.)
4
Æ ALARM
(Check the ALARM input signal.)
5
Æ HOME
(Check the HOME input signal)
6
Æ NHOME
(Check the Near HOME input signal)
7
Æ IN3
(Check the IN3 input signal)
8
Æ INPOS
(Check the INPOS input signal)
9
Æ INDEX
(Check the encoder Z-phase input signal)
Return:
YES: on
Example: if (i8094MF_GET_DI(1, AXIS_X, 1) == YES)
{
//get the status of limit+ sensor of X axis on module 1
}
ICPDAS I-8094 Software User Manual
z
WORD i8094MF_GET_DI_ALL( BYTE cardNo, WORD axis)
Description:
This function reads the digital input (DI) status.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
0x0001
Æ DRIVING
(Check whether the axis is driving or not.)
0x0002
Æ LIMIT+
(Check whether the limit+ is engaged or not.)
0x0004
Æ
0x0008
Æ EMERGENCY (Check whether EMG signal is on or not.)
0x0010
Æ ALARM
(Check the ALARM input signal.)
0x0020
Æ HOME
(Check the HOME input signal)
0x0040
Æ NHOME (Check the Near HOME input signal)
0x0080
Æ IN3
(Check the IN3 input signal)
0x0100
Æ INPOS
(Check the INPOS input signal)
0x0200
Æ INDEX
(Check the encoder Z-phase input signal)
Example: wStatus
= i8094MF_GET_DI_ALL(1, AXIS_X
); if ( ( wStatus & 0x002
) == 0x002 )
{
//get the status of limit+ sensor of X axis on module 1
}
ICPDAS I-8094 Software User Manual
3.6 Reading and Clearing the ERROR Status
z
BYTE i8094MF_GET_ERROR( BYTE cardNo)
Description:
This function checks whether an error occurs or not.
Parameters:
cardNo: Module number
Return:
YES: errors
Please use i8094MF_GET_ERROR_CODE () to get more information. If GET_ERROR_CODE =256, it means that the motion stop was due to the “STOP” command, not because an error happened. Please refer to 6.5.5
and following example to clear ERROR.
NO: No error.
EXAMPLE:
If (i8094MF_GET_ERROR(1) == YES)
{
//read module 1 and ERROR is found
WORD ErrorCode_X = i8094MF_GET_ERROR_CODE(1, AXIS_X);
WORD ErrorCode_Y = i8094MF_GET_ERROR_CODE(1, AXIS_Y);
WORD ErrorCode_Z = i8094MF_GET_ERROR_CODE(1, AXIS_Z);
WORD ErrorCode_U = i8094MF_GET_ERROR_CODE(1, AXIS_U); if ((ErrorCode_X || ErrorCode_Y || ErrorCode_Z || ErrorCode_U) == 256)
{
//It means that motion was stopped due to the stop command was issued, not because any error happened. Please take some actions to clear the malfunction; then clear the STOP status.
i8094MF_CLEAR_STOP(1);
}
}
ICPDAS I-8094 Software User Manual
z
WORD i8094MF_GET_ERROR_CODE( BYTE cardNo, WORD axis)
Description:
This function reads the ERROR status.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
Return:
0
Æ no error
For non-zero return values, please refer to the following table. If there are not only one errors, the return value becomes the sum of these error code values.
For example, a return code 48 means that ALARM and EMGERENCY occurs at the same time.
Error Code Cause of stop
1 SOFT LIMIT+
2
4
SOFT LIMIT-
LIMIT+
8 LIMIT-
16 ALARM
32 EMERGENCY
Explanation
Occurs when the forward software limit is asserted
Occurs when the reverse software limit is asserted
Occurs when the forward hardware limit is asserted
Occurs when the reverse hardware limit is asserted
Occurs when the ALARM is asserted
Occurs when the EMG is asserted
64 Reserved
128 HOME
Reserved
Occurs when both Z phase and HOME are asserted
256
Example: refer to 6.5.4
Occurs when the EMG(software) is asserted if (i8094MF_GET_ ERROR_CODE(1, AXIS_X) & 10 )
{
//Check if either the software limit or hardware limit (2+8)
//in the reverse direction is asserted.
}
ICPDAS I-8094 Software User Manual
4 FRnet Functions (for i8094F only)
4.1 Read FRnet DI Signals
z
WORD i8094MF_FRNET_IN( BYTE cardNo, WORD wRA)
Description:
This function reads the FRnet digital input signals. RA means the
R eceiving
A
ddress which can be one of the legal group number of FRnet. One group comprises 16 bits data. Therefore, total 128 DI can be defined for one FRnet interface.
Parameters:
cardNo: Module number
wRA: Group number, range 8~15
Note: 0~7 are used for digital outputs
Return:
Example:
IN_Data = i8094MF_
FRNET_IN(1, 8);
//Read the 16-bit DI which is on module 1 and the group number is 8.
ICPDAS I-8094 Software User Manual
4.2 Write data to FRnet DO
z
void i8094MF_FRNET_OUT( BYTE cardNo,
WORD wSA, WORD
data)
Description:
This function write data to the FRnet digital output. SA means the
S ending
A
ddress which can be one of the legal group number of FRnet. One group comprises 16 bits data. Therefore, total 128 DO can be defined for one FRnet interface.
Parameters:
cardNo: Module number
wSA: Group number, range 0~7
Note: 8~15 are used by digital inputs
data: 16-bit
Return:
None
Example: i8094MF_
FRNET_OUT(1, 0,0xffff);
//Write 0xffff to the 16-bit DO which is on module 1 and the group number is 0.
ICPDAS I-8094 Software User Manual
5 Auto Homing
The I-8094 module provides an automatic homing function. After setting the appropriate parameters, the assigned axes are able to perform automatic homing.
Settings are required to be made in four steps for performing the automatic HOME search:
z Search for the near home sensor (NHOME) at a normal speed (V). z Search for the HOME sensor at low speed (HV). z Search for the Encoder Z-phase (index) at low speed (HV). z Move a specified number of offset pulses to the predefined origin point at
normal speed (V).
Some steps can be omitted. A detailed description of the related functions is provided in the following sections. Fully automated homing can reduce both programming time and CPU processing time.
Home search is often used when the machine was first opened or the system was occurred the alarm or error signal. Both of two above situations, user can take the home search motion to let the machine return the operation origin.
I-8094 provide the functions that automatically executes a home search sequence such as high-speed near home search
→
low-speed home search
→
encoder Z-phase search
→
offset driving without CPU intervention. Users should dispose the hardware signals as the same as the below figure. The figure shown below illustrates the example of 1-axis driving system. 4 axes can be
assigned in the same way.
X-axis hardware signal disposition
ICPDAS I-8094 Software User Manual
The automatic home search function sequentially executes the steps from step1 to step 4 that are listed below.
Note: If your hardware signal doesn’t have the near home signal ( the
slow-down signal), you can connect the near home and home signal in the same pin, and set the step1 disabled.
Prototype of automatic home search
Note: By inputting a home signal in nIN0 and nIN1, high-speed search is enabled by using only one home signal.
ICPDAS I-8094 Software User Manual
5.1 Setting the Homing Speed
z
void i8094MF_SET_HV( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the homing speed.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: Homing speed (in PPS)
Return:
None
EXAMPLE: i8094MF_ SET_HV(1, AXIS_X, 500);
//set the homing speed of the X axis on module 1 to 500 PPS.
5.2 Using an Limit Switch as the HOME sensor
z
void i8094MF_HOME _LIMIT( BYTE cardNo, WORD axis, WORD nType)
Description:
This function sets the Limit Switch to be used as the HOME sensor.
Parameters:
cardNo: Module number
axis: Axis axes (Please refer to Table 2-1)
nType: 0: Does not use the LIMIT SWITCH as the HOME sensor;
1: Use the LIMIT SWITCH as the HOME sensor
Return:
None
EXAMPLE: i8094MF_ HOME_LIMIT(1, AXIS_X, 0);
//Do not use the Limit Switch as the HOME sensor.
ICPDAS I-8094 Software User Manual
5.3 Setting the Homing Mode
5.3.1 Step 1: High-Speed Near Home Search
Drive pulses are output in the specified direction at the speed that is set in the drive speed (V) until the near home signal (nIN0) becomes active. To perform high-speed search operation, set a higher value for the Acceleration/deceleration driving is performed and when the near home signal (nIN0) becomes active, the operation stops by decelerating.
Home search for step1
Irregular operation
(1) The near home signal (nIN0) is already active before Step 1 starts.
→
Proceeds with Step 2.
(2) The limit signal in the detection direction is already active before Step 1 starts.
→
Proceeds with Step 2.
(3) The limit signal in the detection direction is activated during execution.
→
Stops driving and proceeds with Step 2.
ICPDAS I-8094 Software User Manual
5.3.2 Step 2: Low-Speed Home Search
Drive pulses are output in the specified direction at the speed that is set as the home detection speed (HV) until the home signal (nIN1) becomes active. To perform low-search operation, set a lower value for the home search speed (HV) than the initial speed (SV). A constant speed-driving mode is applied and the operation stops instantly when the home signal (nIN1) becomes active.
Home search for step2
Irregular operation
(1) The home signal (nIN1) is already active before Step 2 starts.
→
The motor drives the axis in the direction opposite to the specified search direction at the home search speed (HV) until the home signal (nIN1) becomes inactive. When the home signal (nIN1) becomes inactive, the function executes
Step2 from the beginning.
(2) The limit signal in the search direction is active before Step 2 starts.
→
The motor drives the axis in the direction opposite to the specified search direction at the home search speed (HV) until the home signal (nIN1) becomes active. When the home signal (nIN1) becomes actives, the motor drivers in the direction opposite to the specified search direction at the home search speed (HV) until the home signal (nIN1) becomes inactive, the function executes Step2 from the beginning.
(3) The limit signal in the search direction becomes active during execution.
→
Driving stops and the same operation as for (2)
→
is performed.
ICPDAS I-8094 Software User Manual
5.3.3 Step 3: Low-Speed Z-phase Search
Drive pulses are output in the specified direction at the speed that is set as the home search speed (HV) until the encoder Z-phase signal (nIN2) becomes active.
To perform low-speed search operation, set a lower value for the home search speed (HV than the initial speed (SV)). A fixed speed-driving mode is applied and driving stops instantly when the encoder Z-phase signal (nIN2) becomes active. As the search condition for stopping driving, the AND condition of the encoder
Z-phase signal (nIN2) and the home signal (nIN1) can be applied.
Home search for step3
Note: (1) If the encoder Z-phase signal (nIN2) is already active at the start
of Step 3, an error occurs. Automatic home search ends. Adjust the mechanical system so that Step 3 always starts from an inactive state with a stable encoder Z-phase signal (nIN2).
(2) If the limit signal in the search direction is already active before the start of Step 3. Automatic home search ends.
(3) If the limit signal in the search direction becomes active during execution, search operation is interrupted. Automatic home search ends.
ICPDAS I-8094 Software User Manual
5.3.4 Step 4: High-Speed Offset Drive
The function outputs as many driving pulses as the pulse count (P) that is set, in the specified direction at the speed that is set in the drive speed (V). Use this step to move the axis from the mechanical home position to the operation home position. Through mode setting, the logical position counter and real position counter can be cleared after moving. If the drive direction limit signal becomes active before the start or during execution of Step 4, the operation stops due to an error and 1 is set in the search direction limit error bit (D2 or D3) of the nRR2 register.
z
void i8094MF_SET_HOME_MODE( BYTE cardNo, WORD axis, WORD nStep1,
WORD nStep2, WORD nStep3, WORD nStep4 , long data)
Description:
This function sets the homing method and other related parameters.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
nStep1:
0: Step 1 is not executed
1: Moves in a positive direction
2: Moves in a negative direction
nStep2:
0: Step 2 is not executed
1: Moves in a positive direction
2: Moves in a negative direction
nStep3:
0: Step 3 is not executed
1: Moves in a positive direction
2: Moves in a negative direction
nStep4:
0: Step 4 is not executed
1: Moves in a positive direction
2: Moves in a negative direction
data: Offset value (0 ~ 2,147,483,647)
ICPDAS I-8094 Software User Manual
The Four Steps Required for Automatic Homing
Step
1
2
Action
Searching for the Near Home sensor
Searching for the HOME sensor
Speed
V
HV
Sensor
NHOME (IN0)
HOME (IN1)
3
Searching for the encoder Z-phase signal
4 Moves to the specified position
Return:
None
V
Example:
//Use the following functions to set the homing mode of the X axis. i8094MF_SET_V(1, 0x1, 20000);
Step
1
2
3
4 i8094MF_SET_HOME_MODE(1, 0x1, 2, 2, 1, 1, 3500); i8094MF_HOME_START(1, 0x1); //start auto-homing. i8094MF_WAIT_HOME(1, 0x1); //wait until homing is completed.
Input Signal
Near HOME (IN0) is active
HOME (IN1) is active
Z-phase (IN2) is active
No sensor is required. Move 3500 pulses along the X axis.
Direction
-
-
+
+
Speed
20000 PPS (V)
500 PPS (HV)
500 PPS (HV)
20000 PPS (V)
ICPDAS I-8094 Software User Manual
5.4 Starting the Homing Sequence
z
void i8094MF_HOME _START( BYTE cardNo, WORD axis)
Description:
This function starts the home search of assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_ HOME_START(1, AXIS_X);
//start the automatic homing sequence for the X axis on module 1.
5.5 Waiting for the Homing sequence to be Completed
z
BYTE i8094MF _HOME_WAIT( BYTE cardNo, WORD axis)
Description:
This function assigns commands to be performed while waiting for the automatic home search of all assigned axes to be completed.
Parameters:
cardNo: Module number
axis: Axis axes (Please refer to Table 2-1)
Return:
Example:
YES The Homing sequence has been completed.
NO The Homing sequence is not complete. if (i8094MF_HOME_WAIT(1, AXIS_X) == NO)
{
//perform some actions here if the X axis on module 1 has not completed
//its homing sequence.
}
ICPDAS I-8094 Software User Manual
6 General Motion Control
6.1 Independent Axis Motion Control
z The motion of each axis can be started independently. z Multiple axes are moving at the same time. z Each axis is moving independently. z Each axis can be commanded to change motion, such as changing the number
of pulses or the speed.
z Each axis can be commanded to stop slowly or suddenly to meet the individual
requirements.
z Independent axis motion can work with interpolation or synchrous action to do
more complicated and versatile motion.
6.1.1 Setting the Acceleration/Deceleration Mode
Symmetric T-curve Asymmetric T-curve
Symmetric S-curve
ICPDAS I-8094 Software User Manual
z
void i8094MF_NORMAL_SPEED( BYTE cardNo, WORD axis , WORD nMode)
Description:
The function sets the speed mode.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1)
nMode:
0
Æ Symmetric T-curve (Please set SV, V, A, and AO)
1
Æ Symmetric S-curve (Please set SV, V, K, and AO)
2
Æ Asymmetric T-curve (Please set SV, V, A, D, and AO)
3
Æ Asymmetric S-curve (Please set SV, V, K, L, and AO)
Return:
None
Example:
BYTE cardNo=1; //select module 1. i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the max. speed of XYZU axes to 20K PPS.
//======================================================== i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU, 0);
//use a symmetric T-curve for all axes on module 1.
i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_A(cardNo, AXIS_XYZU,1000);
//set the acceleration of all axes on module 1 to 1000 PPS/Sec.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 2000);
//set the start speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the number of remaining offset pulses for all axes to 9 pulses.
i8094MF_FIXED_MOVE(cardNo, AXIS_XYZU, 10000);
//move all axes on module 1 for 10000 pulses.
//======================================================== i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU,1);
//use a symmetric S-curve for all axes on module 1.
i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_K(cardNo, AXIS_XYZU, 50);
//set the acceleration rate of all axes on module 1 to 500 PPS/Sec^2.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 200);
//set the start speed of all axes on module 1 to 200 PPS.
i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the number of remaining offset pulses to 9 pulses for all axes.
ICPDAS I-8094 Software User Manual
i8094MF_FIXED_MOVE(cardNo, AXIS_XYZU, -10000);
//move all axes on module 1 for 10000 pulses in reverse direction.
//======================================================== i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU,2);
//use an asymmetric T-curve for all axes on module 1.
i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_A(cardNo, AXIS_XYZU,1000 );
//set the acceleration of all axes on module 1 to 1000 PPS/Sec.
i8094MF_SET_D(cardNo, AXIS_XYZU, 500);
//set the deceleration of all axes on module 1 to 500 PPS.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 200);
//set the start speed of all axes on module 1 to 200 PPS.
i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the number of remaining offset pulses to 9 pulses for all axes.
i8094MF_FIXED_MOVE(cardNo, axis, 10000);
//move all axes on module 1 for 10000 pulses.
//======================================================== i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU,3);
//use an asymmetric S-curve for all axes on module 1.
i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_K(cardNo, AXIS_XYZU, 50);
//set the acceleration rate of all axes on module 1 to 500 PPS/Sec^2.
i8094MF_SET_L(cardNo, AXIS_XYZU, 30);
//set the deceleration rate of all axes on module 1 to 300 PPS/Sec^2.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 200);
//set the start speed of all axes on module 1 to 200 PPS.
i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the number of remaining offset pulses to 9 pulses for all axes.
i8094MF_FIXED_MOVE(cardNo, AXIS_XYZU, 10000);
//move all axes on module 1 for 10000 pulses.
Note: Relevant parameters must be set to achieve the desired motion.
ICPDAS I-8094 Software User Manual
6.1.2 Setting the Start Speed
z
void i8094MF_SET_SV( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the start speed for the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The range is the same as for speed, and must not be zero or larger than the maximum speed. The maximum value is
4,000,000 PPS. For interpolation, set the speed value for axis1 is enough.
Return:
None
Example: i8094MF_SET_SV(1, AXIS_X, 1000);
//set the starting speed for the X axis on module 1 to 1000 PPS.
ICPDAS I-8094 Software User Manual
6.1.3 Setting the Desired Speed
z
void i8094MF_SET_V( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the desired speed for the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The range is the same as for speed, and must not be zero or larger than the maximum speed. The maximum value is
4,000,000 PPS. For interpolation, set the speed value for axis1 is enough.
Return:
None
Example: i8094MF_SET_V(1, AXIS_X, 120000L);
//set the speed for the X axis on module 1 to 120000 PPS.
6.1.4 Setting the Acceleration
z
void i8094MF_SET_A( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the acceleration value for the assigned axes.
Parameters:
axis:
data:
Axis or axes (Please refer to Table 2-1)
The acceleration value. The units are PPS/Sec. This value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available acceleration value is MAX_V * 125 . The minimum acceleration value is MAX_V
÷
64 , and all other acceleration values are the integral multipliers of this value. The practical value for application depends on the capability of the motor drive and motor.
ICPDAS I-8094 Software User Manual
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any acceleration value that is larger than
//20,000*125 PPS/sec. And 20,000 *125 = 2,500,000. i8094MF_SET_A(1, AXIS_X, 100000L);
//set the acceleration value of the X axis on module 1 to 100K PPS/Sec.
ICPDAS I-8094 Software User Manual
6.1.5 Setting the Deceleration
z
void i8094MF_SET_D( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the deceleration value for the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The deceleration value. The units are PPS/Sec. This value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available deceleration value is MAX_V * 125 . The minimum deceleration value is MAX_V
÷
64 , and all other deceleration values are the integral multipliers of this value. The practical value for application depends on the capability of the motor drive and motor.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any deceleration value that is larger than
//20,000*125 PPS/sec. And 20,000 *125 = 2,500,000.
i8094MF_SET_D(1, AXIS_X, 100000L);
//set the deceleration value of the X axis on module 1 to 100K PPS/Sec.
ICPDAS I-8094 Software User Manual
6.1.6 Setting the Acceleration Rate
z
void i8094MF_SET_K( BYTE cardNo, WORD axis, DWORD data)
Description:
The function sets the acceleration rate (i.e., Jerk) value for the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The acceleration rate (jerk) value. The units are
2
PPS/Sec . This
value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available acceleration rate value is MAX_V * 781.25
. The minimum acceleration value is MAX_V *
0.0119211
, and all other acceleration values are the integral multipliers of this value.
The practical value for application depends on the capability of the motor drive and motor. Note: since the DWORD can not represent the maximum value; therefore, this value is given by dividing the desired value by 10.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any jerk value that is larger than
//20,000*781.25 PPS/sec^2. And 20,000 *781.25 = 15,625,000. i8094MF_SET_K(1, AXIS_X, 1000);
//set the acceleration rate value of the X axis on module 1 to
//1,000*10 (= 10,000) PPS/Sec^2.
ICPDAS I-8094 Software User Manual
6.1.7 Setting the Deceleration Rate
z
void i8094MF_SET_L( BYTE cardNo, WORD axis, DWORD data)
Description:
This function sets the deceleration rate (i.e., Jerk) value for the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The deceleration rate value. The units are
2
PPS/Sec . This
value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available deceleration rate value is MAX_V * 781.25
. The minimum deceleration value is MAX_V *
0.0119211
, and all other deceleration values are the integral multipliers of this value.
The practical value for application depends on the capability of the motor drive and motor. Note: since the DWORD can not represent the maximum value; therefore, this value is given by dividing the desired value by 10.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any deceleration rate value that is larger
//than 20,000*781.25 PPS/sec^2. And 20,000 *781.25 = 15,625,000. i8094MF_SET_L(1, AXIS_X, 1000);
//set the acceleration rate value of the X axis on module 1 to
//1,000*10 (= 10,000) PPS/Sec^2.
ICPDAS I-8094 Software User Manual
6.1.8 Setting the Value of the Remaining Offset Pulses
z
void i8094MF_SET_AO( BYTE cardNo, WORD axis, short int data)
Description:
This function sets the number of remaining offset pulses for the assigned axes.
Please refer to the figure below for a definition of the remaining offset pulse value.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
data: The number of remaining offset pulses. (-32,768 ~ +32,767)
Return:
None
Example: i8094MF_SET_AO(1, AXIS_X, 200);
//set the number of remaining offset pulses for the X axis on
//module 1 to 200 pulses.
ICPDAS I-8094 Software User Manual
6.1.9 Fixed Pulse Output
z
BYTE i8094MF_FIXED_MOVE( BYTE cardNo, WORD axis, long data)
Description:
Command a point-to-point motion for several independent axes.
Parameters:
cardNo: Module number
axis: Axis (Please refer to Table 2-1.)
The axis can be either X, Y, Z, or U.
data: Pulses (-2,147,483,648 ~ +2,147,483,647)
Return:
YES Some errors happen. Use i8094MF_GET_ERROR_CODE () to
Example:
BYTE cardNo=1; //select module 1 i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the max. velocity of all axes on module 1 to be 20K PPS i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU, 0);
//set the speed profile of all axes on module 1 to be symmetric T-curve i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to be 2000 PPS i8094MF_SET_A(cardNo, AXIS_XYZU,1000);
//set the acceleration value of all axes on module 1 to be 1000 PPS/S i8094MF_SET_SV(cardNo, AXIS_XYZU, 2000);
//set the start velocity of all axes on module 1 to be 2000 PPS i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the remaining offset pulses to be 9 PPS i8094MF_FIXED_MOVE(cardNo, AXIS_XYZU, 10000);
// move 10000 Pulses for each axis on module 1
ICPDAS I-8094 Software User Manual
6.1.10 Continuous Pulse Output
z
BYTE i8094MF_CONTINUE_MOVE( BYTE cardNo, WORD axis, long data)
Description:
This function issues a continuous motion command for several independent axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
The axis can be either X, Y, Z, or U.
data: The specified speed (positive value for CW motion; negative value for CCW motion)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the errors.
Example:
BYTE cardNo=1; //select module 1 i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the maximum speed of all axes on module 1 to 20K PPS. i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU, 0);
//set the speed profile for all axes as a symmetric T-curve.
i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_A(cardNo, AXIS_XYZU, 1000);
//set the acceleration value of all axes to 1000 PPS/S.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 2000);
//set the start velocity of all axes to 2000 PPS i8094MF_CONTINUE_MOVE(cardNo, AXIS_XYZU, 1000);
//move all axes on module 1 at a speed of 1000 PPS.
ICPDAS I-8094 Software User Manual
6.2 Interpolation Commands
6.2.1 Assigning the Axes for Interpolation
z
void i8094MF_AXIS_ASSIGN( BYTE cardNo, WORD axis1, WORD axis2, WORD
axis3)
Description:
This function assigns the axes to be used for interpolation. Either two or three axes can be assigned using this function. Interpolation commands will refer to the assigned axes to construct a working coordinate system. The X axis does not necessarily have to be the first axis. However, it is easier to use the X axis as the first axis, the Y axis as the second axis, and the Z axis as the third axis.
Parameters:
cardNo: Module number
axis1: The first axis and It can be either X, Y, Z, or U.
Please refer to Table 2-1 for the axis definition.
axis2: The second axis and can be either X, Y, Z, or U.
axis3: The third axis and can be either X, Y, Z, or U.
Return:
None
EXAMPLE: i8094MF_AXIS_ASSIGN(1, AXIS_X, AXIS_Y, 0);
//set the X axis of module 1 as the first axis and the Y axis as the second axis.
ICPDAS I-8094 Software User Manual
6.2.2 Setting the Speed and Acc/Dec Mode for Interpolation
z
void i8094MF_VECTOR_SPEED( BYTE cardNo, WORD nMode)
Description:
This function assigns the mode of interpolation. Either two or three axes will join this interpolation. Each interpolation mode will refer to some assigned axes that construct a working coordinate system. The assigned axes are defined by i8094MF_AXIS_ASSIGN() funciton. The X axis does not necessarily have to be the first axis. However, it is easier to let the X axis as the first axis, the Y axis as the second axis, and the Z axis as the third axis in applications. Different modes need different settings. Please refer to the mode definitions.
Parameters:
cardNo: Module number
nMode: 0
Æ 2-axis linear or circular motion at a constant vector speed
(Set VV and VSV; and VV=VSV)
1
Æ 2-axis linear motion using a symmetric T-curve velocity profile
(set VSV, VV, VA, and VAO)
2
Æ 2-axis linear motion using a symmetric S-curve velocity profile
(set VSV, VV, VK, and VAO)
3
Æ 2-axis linear motion using an asymmetric T-curve velocity
profile (set VSV, VV, VA, VD, and VAO)
4
Æ 2-axis linear motion using an asymmetric S-curve velocity
profile (set VSV, VV, VK, VL, and VAO)
5
Æ 2-axis circular motion using a symmetric T-curve velocity
profile (set VSV, VV, VA, and VAO)
6
Æ 2-axis circular motion using an asymmetric T-curve velocity
profile (set VSV, VV, VA, VD, and VAO)
7
Æ 3-axis linear motion at a constant vector speed
(set VV and VSV; and VV=VSV)
8
Æ 3-axis linear motion at using a symmetric T-curve velocity
profile (set VSV, VV, VA, and VAO)
9
Æ 3-axis linear motion using a symmetric S-curve velocity profile
(set VSV, VV, VK, and VAO)
10
Æ3-axis linear motion using an asymmetric T-curve velocity
profile (set VSV, VV, VA, VD, and VAO)
11
Æ3-axis linear motion using an asymmetric S-curve velocity
profile (set VSV, VV, VK, VL, and VAO)
Return:
None
ICPDAS I-8094 Software User Manual
Example:
BYTE cardNo=1; //select module 1. i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the maximum speed of all axes to 20K PPS.
//=============================================== i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 0);
//set module 1 to perform 2-axis linear or circular motion
//at a constant vector speed. i8094MF_SET_VSV(cardNo, 1000);
//set the starting vector speed to 1000 PPS.
1000);
//set the vector speed to 1000 PPS.
i8094MF_LINE_2D(1, 12000, 10000);
//execute the 2-axis linear interpolation motion.
//===============================================
//enable the deceleration function.
i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 1);
//set module 1 to perform 2-axis linear motion using a symmetric
//S-curve velocity profile. i8094MF_SET_VSV(cardNo, 500);
//set the starting vector speed to 500 PPS.
i8094MF_SET_VV(cardNo, 2000);
//set the vector speed to 2000 PPS.
i8094MF_SET_VA(cardNo, 1000);
//set the vector acceleration to 1000 PPS/Sec.
i8094MF_LINE_2D(cardNo, 20000, 10000);
//execute the 2-axis linear interpolation motion.
//=============================================== i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 2);
//2-axis linear motion using a symmetric S-curve velocity profile. i8094MF_SET_VSV(cardNo, 200);
//set the starting vector speed to 200 PPS.
i8094MF_SET_VV(cardNo, 2000);
//set the vector speed to 2000 PPS. i8094MF_SET_VK(cardNo, 50);
//set the acceleration rate to 500 PPS/Sec.
i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20.
ICPDAS I-8094 Software User Manual
i8094MF_LINE_2D(cardNo, 10000, 10000);
//execute the 2-axis linear interpolation motion.
//===============================================
//enable the deceleration function.
i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 3);
//2-axis linear motion using an asymmetric T-curve velocity profile. i8094MF_SET_VSV(cardNo, 100);
//set the start vector speed to 100 PPS.
i8094MF_SET_VV(cardNo, 2000);
//set the vector speed to 2000 PPS. i8094MF_SET_VA(cardNo, 1000);
//set the vector acceleration to 1000 PPS/Sec. i8094MF_SET_VD(cardNo, 500);
//set the vector deceleration to 500 PPS/Sec. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_2D(cardNo, 10000, 5000);
//execute the 2-axis linear interpolation motion.
//=============================================== long fp1=4000; long fp2=10000; int sv=200; int v=2000; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 8000); i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 4);
//2-axis linear motion using an asymmetric S-curve velocity profile. i8094MF_SET_VSV(cardNo, sv);
//set the starting velocity to sv PPS. i8094MF_SET_VV(cardNo, v);
//set the vector speed to v PPS. i8094MF_SET_VK(cardNo, 50);
//set the acceleration rate to 500 PPS/Sec^2. i8094MF_SET_VL(cardNo, 30);
//set the deceleration rate to 300 PPS/Sec^2. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_2D(cardNo, fp1, fp2);
//execute the 2-axis linear motion.
//=============================================== long fp1=11000;
ICPDAS I-8094 Software User Manual
long fp2=9000; long c1=10000; long c2=0; int sv=100; int v=3000; int a=5000; int d=5000; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 8000); i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 5);
//2-axis circular motion using a symmetric T-curve velocity profile i8094MF_SET_VSV(cardNo, sv);
//set the starting vector speed to sv PPS. i8094MF_SET_VV(cardNo, v);
//set vector speed to v PPS. i8094MF_SET_VA(cardNo, a);
//set the vector acceleration to a PPS/Sec. i8094MF_SET_VAO(cardNo, 0);
//set the value of remaining offset pulses to 0 Pulse. i8094MF_ARC_CW(cardNo, c1,c2, fp1, fp2);
//execute the 2-axis CW circular motion.
//=============================================== long c1=300; long c2=0; int sv=100; int v=3000; int a=125; int d=12; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 8000); i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X axis as the first axis and the Y axis as the second axis. i8094MF_VECTOR_SPEED(cardNo, 6);
// 2-axis circular motion using an asymmetric T-curve velocity
//profile.
i8094MF_SET_VSV(cardNo, sv);
//set the starting vector speed to sv PPS. i8094MF_SET_VV(cardNo, v);
//set vector speed to v PPS. i8094MF_SET_VA(cardNo, a);
//set acceleration to a PPS/Sec. i8094MF_SET_VD(cardNo, d);
//set the deceleration to d PPS/Sec. i8094MF_SET_VAO(cardNo, 0);
//set the value of remaining offset pulses to 0. i8094MF_CIRCLE_CW(cardNo, c1, c2);
ICPDAS I-8094 Software User Manual
//execute the 2-axis CW circular motion.
//=============================================== i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, AXIS_Z);
//set axis1 as the X axis, axis2 as the Y axis, and axis3 as the Z axis. i8094MF_VECTOR_SPEED(cardNo, 7);
//3-axis linear motion at a constant vector speed (VSV=VV). i8094MF_SET_VSV(cardNo, 1000);
//set the start speed to 1000 PPS. i8094MF_SET_VV(cardNo, 1000);
//set the constant speed to 1000 PPS. i8094MF_LINE_3D(cardNo, 10000, 10000,10000);
//execute the 3-axis linear motion.
//=============================================== i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, AXIS_Z);
//set axis1 as the X axis, axis2 as the Y axis, and axis3 as the Z-axis. i8094MF_VECTOR_SPEED(cardNo, 8);
// 3-axis linear motion using a symmetric T-curve velocity profile.
i8094MF_SET_VSV(cardNo, 100);
//set the starting speed to 1000 PPS. i8094MF_SET_VV(cardNo, 3000);
//set the vector speed to 3000 PPS. i8094MF_SET_VA(cardNo, 500);
//set the vector acceleration to 500 PPS/Sec. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_3D(cardNo, 10000, 1000,20000);
//execute the 3-axis linear motion
//=============================================== i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, AXIS_Z);
//set the axis1 as the X axis, axis2 as the Y axis, and axis3 as the Z axis. i8094MF_VECTOR_SPEED(cardNo, 9);
//3-axis linear motion using a symmetric S-curve velocity profile. i8094MF_SET_VSV(cardNo, 100);
//set the starting speed to 1000 PPS. i8094MF_SET_VV(cardNo, 3000);
//set the vector speed to 3000 PPS. i8094MF_SET_VK(cardNo, 50);
//set the vector acceleration rate to 500 PPS/Sec^2. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_3D(cardNo, 10000, 1000,1000);
//execute the 3-axis linear motion.
//===============================================
ICPDAS I-8094 Software User Manual
i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, AXIS_Z);
//set the axis1 as the X axis, axis2 as the Y axis, and axis3 as the Z axis. i8094MF_VECTOR_SPEED(cardNo, 10);
//set the module 1 to perform 3-axis linear motion
//using an asymmetric T-curve speed profile. i8094MF_SET_VSV(cardNo, 100);
//set the starting speed to 1000 PPS. i8094MF_SET_VV(cardNo, 2000);
//set the vector speed as 3000 PPS. i8094MF_SET_VA(cardNo, 1000);
//set the vector acceleration to 1000 PPS/Sec. i8094MF_SET_VD(cardNo, 500);
//set the vector deceleration to 500 PPS/Sec. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_3D(cardNo, 10000, 1000,1000);
//execute the 3-axis linear motion.
//=============================================== long fp1=4000; long fp2=10000; long fp3=20000; int sv=200; int v=2000; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 8000); i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, AXIS_Z);
//set axis1 as the X axis, axis2 as the Y axis, and axis3 as the Z axis. i8094MF_VECTOR_SPEED(cardNo, 11);
//3-axis linear motion using an asymmetric S-curve velocity profile. i8094MF_SET_VSV(cardNo, sv);
//set the starting speed to sv PPS. i8094MF_SET_VV(cardNo, v);
//set the vector speed to v PPS. i8094MF_SET_VK(cardNo, 50);
//set the vector acceleration rate to 500 PPS/Sec^2. i8094MF_SET_VL(cardNo, 30);
//set the vector deceleration rate to 300 PPS/Sec^2. i8094MF_SET_VAO(cardNo, 20);
//set the value of remaining offset pulses to 20. i8094MF_LINE_3D(cardNo, fp1, fp2,fp3);
//execute the 3-axis linear motion.
Note: Relevant parameters should be set before issuing the motion command.
6.2.3 Setting the Vector Starting Speed
z
void i8094MF_SET_VSV( BYTE cardNo, DWORD data)
ICPDAS I-8094 Software User Manual
Description:
This function sets the starting speed of the principle axis (axis 1) for the interpolation motion.
Parameters:
cardNo: Module number
data: The vector starting speed value (in PPS)
Return:
None
Example: i8094MF_SET_VSV(1, 1000);
//set the starting speed of the axis 1 for the interpolation motion
//on module 1 to 1000 PPS.
6.2.4 Setting the Vector Speed
z
void i8094MF_SET_VV( BYTE cardNo, DWORD data)
Description:
This function sets the vector speed of the interpolation motion. Users do not need to assign any axes on this function. The speed setting will take effect on the current working coordinate system which is defined by the i8094MF_AXIS_ASSIGN() function.
Parameters:
cardNo: Module number
data: The vector speed value (in PPS)
Return:
None
Example: i8094MF_SET_VV(1, 120000L);
//set the vector speed of the interpolation on module 1
//to 120000 PPS.
6.2.5 Setting the Vector Acceleration
z
void i8094MF_SET_VA( BYTE cardNo, DWORD data)
ICPDAS I-8094 Software User Manual
Description:
This function sets the vector acceleration for interpolation motion. Users do not have to assign any axes on this funciton. This speed setting will take effect on the current working coordinate system which is defined by the i8094MF_AXIS_ASSIGN() function.
Parameters:
cardNo: Module number
data: The vector acceleration value (in PPS/Sec). The units are
PPS/Sec. This value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available acceleration value is MAX_V * 125 . The minimum acceleration value is MAX_V
÷
64 , and all other acceleration values are the integral multipliers of this value. The practical value for application depends on the capability of the motor drive and motor.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any acceleration value that is larger than
//20,000*125 PPS/sec. And 20,000 *125 = 2,500,000.
i8094MF_SET_VA(1, 100000L);
//set the vector acceleration of the interpolation motion
//on module 1 to 100K PPS/Sec.
6.2.6 Setting the Vector Deceleration Value
z
void i8094MF_SET_VD( BYTE cardNo, DWORD data)
Description:
ICPDAS I-8094 Software User Manual
This function sets the deceleration value for the interpolation motion.
Parameters:
cardNo: Module number
data: The vector deceleration value (in PPS/Sec). This value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available deceleration value is MAX_V * 125 . The minimum deceleration value is MAX_V
÷
64 , and all other deceleration values are the integral multipliers of this value. The practical value for application depends on the capability of the motor drive and motor.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any deceleration value that is larger than
//20,000*125 PPS/sec. And 20,000 *125 = 2,500,000. i8094MF_SET_VD(1, 100000L);
//set the vector deceleration value of interpolation motion
//on module 1 to 100K PPS/Sec.
6.2.7 Setting the Vector Acceleration Rate
z
void i8094MF_SET_VK( BYTE cardNo, DWORD data)
Description:
Set the acceleration rate (jerk) value for interpolation motion.
ICPDAS I-8094 Software User Manual
Parameters:
cardNo: Module number
data: The acceleration rate (jerk) value. The units are
2
PPS/Sec . This
value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available acceleration rate value is MAX_V * 781.25
. The minimum acceleration value is MAX_V *
0.0119211
, and all other acceleration values are the integral multipliers of this value.
The practical value for application depends on the capability of the motor drive and motor. Note: since the DWORD can not represent the maximum value; therefore, this value is given by dividing the desired value by 10.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any jerk value that is larger than
//20,000*781.25 PPS/sec^2. And 20,000 *781.25 = 15,625,000. i8094MF_SET_VK(1, 10000);
//set the acceleration rate of the interpolation motion on module
// 1 to 10,000 PPS/ Sec^2.
6.2.8 Setting the Vector Deceleration Rate
z
void i8094MF_SET_VL( BYTE cardNo, DWORD data)
Description:
This function sets the deceleration rate of the interpolation motion.
ICPDAS I-8094 Software User Manual
Parameters:
cardNo: Module number
data: The deceleration rate (Jerk) value. The units are
2
PPS/Sec .
This value is related to the maximum speed value defined by i8094MF_SET_MAX_V() function. The maximum available deceleration rate value is MAX_V * 781.25
. The minimum deceleration value is MAX_V *
0.0119211
, and all other deceleration values are the integral multipliers of this value.
The practical value for application depends on the capability of the motor drive and motor. Note: since the DWORD can not represent the maximum value; therefore, this value is given by dividing the desired value by 10.
Return:
None
Example: i8094MF_SET_MAX_V(1, AXIS_X, 20000);
//set the maximum speed value of the X axis as 20,000 PPS.
//therefore, do not set any deceleration rate value that is larger
//than 20,000*781.25 PPS/sec^2. And 20,000 *781.25 = 15,625,000. i8094MF_SET_VL(1, 10000);
//set the deceleration rate of the interpolation on module 1 to 10,000 PPS/Sec^2.
6.2.9 Setting the Number of the Remaining Offset Pulses
z
void i8094MF_SET_VAO( BYTE cardNo, short int data)
Description:
Setting this value will cause the motion control chip to start deceleration earlier. The remaining offset pulses will be completed at low speed to allow the controller to stop immediately when the offset pulse value has been reached.
ICPDAS I-8094 Software User Manual
Please refer to the figure below for more information.
Parameters:
cardNo: Module number
data: The number of remaining offset pulses (-32,768 ~ +32,767)
Return:
None
Example: i8094MF_SET_VAO(1, 200);
//set the number of remaining offset pulse value on module 1 to 200.
6.2.10 2-Axis Linear Interpolation Motion
z
BYTE i8094MF_LINE_2D( BYTE cardNo, long fp1, long fp2)
Description:
This function executes a 2-axis linear interpolation motion.
Parameters:
ICPDAS I-8094 Software User Manual
cardNo: Module number
fp1: The displacement of the axis 1 in Pulses
(-2,147,483,648 ~ +2,147,483,647)
fp2: The displacement of the axis 2 in Pulses
(-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the error.
Example: i8094MF_LINE_2D(1, 12000, 10000);
//execute the 2-axis linear interpolation motion on module 1.
2-axis linear interpolation motion
6.2.11 3-axis Linear Interpolation Motion
z
BYTE i8094MF_LINE_3D( BYTE cardNo, long fp1, long fp2, long fp3)
Description:
This function executes a 3-axis linear interpolation motion.
Parameters:
ICPDAS I-8094 Software User Manual
cardNo: Module number
fp1: The displacement of the first axis (axis 1) in Pulses
(-2,147,483,648 ~ +2,147,483,647)
fp2: The displacement of the second axis (axis 2) in Pulses
(-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the error.
Example: i8094MF_LINE_3D(1, 10000, 10000, 10000);
//execute the 3-axis linear interpolation motion on module 1.
3-axis linear interpolation motion
6.2.12 2-Axis Circular Interpolation Motion (an Arc)
z
BYTE i8094MF_ARC_CW( BYTE cardNo, long cp1, long cp2, long fp1, long fp2)
Description:
This function executes a 2-axis circular interpolation motion in a clockwise
(CW) direction.
ICPDAS I-8094 Software User Manual
Parameters:
cardNo: Module number
cp1: The relative position of the center to the current position of axis 1 in pulses. (-2,147,483,648 ~ +2,147,483,647)
cp2: The relative position of the center to the current position of axis 2 in pulses. (-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example: i8094MF_ARC_CW(1, -5000, -5000, -10000, -10000);
//Issues a command to perform a circular motion (an arc)
//in a CW direction. Please refer to the following figure.
2-axis circular motion in a CW direction
z
BYTE i8094MF_ARC_CCW( BYTE cardNo, long cp1, long cp2, long fp1, long fp2)
Description:
This function execute a 2-axis circular interpolation motion in a counter-clockwise (CCW) direction.
Parameters:
cardNo: Module number
ICPDAS I-8094 Software User Manual
cp1: The relative position of the center to the current position of axis 1 in pulses. (-2,147,483,648 ~ +2,147,483,647)
cp2: The relative position of the center to the current position of axis 2 in pulses. (-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the errors.
Example: i8094MF_ARC_CCW(1, -5000, -5000, -10000, -10000);
//Issues a command to perform a circular motion (an arc)
//in a CCW direction. Refer to the following figure.
2-axis circular motion in a CCW direction
6.2.13 2-Axis Circular Interpolation Motion (a Complete Circle)
z
BYTE i8094MF_CIRCLE_CW( BYTE cardNo, long cp1, long cp2)
Description:
This function executes a 2-axis circular interpolation motion in a clockwise
(CW) direction.
ICPDAS I-8094 Software User Manual
Parameters:
cardNo: Module number
cp1: The relative position of the center to the current position of axis 1 in pulses. (-2,147,483,648 ~ +2,147,483,647)
cp2: The relative position of the center to the current position of axis 2 in pulses. (-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the errors.
Example: i8094MF_CIRCLE_CW(1, 0, 10000);
//execute a circular motion (a complete circle) in a CW direction on module 1.
z
BYTE i8094MF_CIRCLE_CCW( BYTE cardNo, long cp1, long cp2)
Description:
This function executes a 2-axis circular interpolation motion in a counter-clockwise (CCW) direction.
Parameters:
cardNo: Module number
cp1: The relative position of the center to the current position of axis 1 in pulses. (-2,147,483,648 ~ +2,147,483,647)
cp2: The relative position of the center to the current position of axis 2 in pulses. (-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example: i8094MF_CIRCLE_CCW(1, 0, 10000);
ICPDAS I-8094 Software User Manual
//execute a circular motion (a circle) in CCW direction
//on module 1
6.3 Synchronous Actions
6.3.1 Setting the Synchronous Action
z
void i8094MF_SYNC_ACTION( BYTE cardNo, WORD
axis1,
WORD axis2,
WORD nSYNC, WORD nDRV, WORD nLATCH, WORD nPRESET)
Description:
This function sets the activation factors (provocatives) and the specified
ICPDAS I-8094 Software User Manual
action when a specified activation factor occurs.
Parameters:
cardNo: Module number
axis1: This is the monitored axis. It will be checked by hardware.
The axis can be either X, Y, Z, or U. (Please refer to Table 2-1.)
axis2: This defined the other axes (or axis) that will take action when one of the activation factors occurs. The axes are defined in the following table.
axis1 axis2
X Y Z U
0
1
2
3
4
5 none none none none
Y Z U X
Z U X Y
YZ ZU UX XY
U X Y Z
YU ZX UY XZ
6
7
ZU UX XY YZ
YZU ZUX UXY XYZ
nSYNC: It defines the activation factors. Multiple activation factors can be defined at the same time. Available active factors are listed in the following table.
Value Event Explanation
0x0000 Disable the synchronous action
0x0001 P
≥
C+
The logical/real position counter value exceeded the
COMP+ register value.
Use the i8094MF_SET_COMPARE() function for selection of a logical/real position.
The logical/real position counter value became less
0x0002 P<C+ than the COMP+ register value.
Use the i8094MF_SET_COMPARE() function for selection of a logical/real position.
The logical/real position counter value became less
0x0004 P<C- than the COMP- register value.
Use the i8094MF_SET_COMPARE() function for selection of a logical/real position.
0x0008 P
≥
C-
The logical/real position counter value exceeded the COMP- register value.
Use the i8094MF_SET_COMPARE() function for selection of a logical/real position.
ICPDAS I-8094 Software User Manual
0x0040 IN3
0x0080 IN3
↑
The nIN3 signal rose from the Low to the High level.
↓
The nIN3 signal fell from the High to the Low level.
For example, if the factors P
≥
C+ and IN3
↑
are set, the nSYNC value is 0x0041
(0x0001 + 0x0040 = 0x0041 ).
nDRV: It defines the actions that are related with axial driving.
Available actions are listed in the following table. Only one driving action can be chosen.
Value Symbol Explanation
0 Disable driving action.
Activates fixed pulse driving in the + direction. It must set the nPRESET value to be “ OPSET ” which indicates that i8094MF_SET_PRESET() function will companion function, i8094MF_SET_PRESET(), is necessary. However, this command does not take effect if the assigned axes, axis2, are moving.
Activates fixed pulse driving in the - direction. It must set the nPRESET value to be “ OPSET ” which indicates that i8094MF_SET_PRESET() function will companion function, i8094MF_SET_PRESET(), is necessary. However, this command does not take effect if the assigned axes, axis2, are moving.
Activates continuous pulse driving in the + effect if the assigned axes, axis2, are moving.
Activates continuous pulse driving in the - direction.
5
6 assigned axes, axis2, are moving.
SSTOP Stop driving in deceleration.
ISTOP Stop driving immediately.
nLATCH: It defines the actions that is related of latching position.
Available actions are listed in the following table. Only one of these actions can be chosen.
Value Symbol Explanation
0 Disable position latch function.
Saves the current logical position counter value (LP)
2
[LP
→
LATCH]
EPSAV Saves the current real position counter value (EP) in
ICPDAS I-8094 Software User Manual
the synchronous buffer register (BR).
[EP
→
LATCH]
After the event is occoured, the i8094MF_GET_LATCH() function can be use to get the latched value.
nPRESET: It defines the actions that is related of latching position.
Available actions are listed in the following table. Only one of these actions can be chosen.
Value Symbol Explanation
0 Disable setting function.
Indicates that a new value for the logical position
( LP ) will be set. The new value will be set by
1 LPSET i8094MF_SET_PRESET() function.
[LP
←
PRESET]
Indicates that a new value for the real position ( EP ) will be set. The new value will be set by
2 EPSET i8094MF_SET_PRESET() function.
[EP
←
PRESET]
Indicates that a new offset value ( P ) for the fixed pulse driving will be set. The new value will be set by
3 OPSET i8094MF_SET_PRESET() function.
[P
←
PRESET]
Indicates that a new speed value ( V ) will be set. The new value will be set by i8094MF_SET_PRESET()
4 VLSET function.
[V
←
PRESET]
Return:
None
Example:
//Ex1. When the rising edge event of
IN3 signal of U-axis occurred,
// the real position (EP) is latched and the driving speed of U-axis is changed, too. i8094MF_SYNC_ACTION(cardNo, AXIS_U, 0, 0X0040, 0, 2, 4);
//Set the maximum speed of U-axis to 5K PPS.
//Set the Acc/Dec mode to be symmetric T-curve.
//Set the speed of U-axis to 2000 PPS.
//Set the acceleration of U-axis to 100K PPS/S.
ICPDAS I-8094 Software User Manual
//Set the start speed of U-axis to 100 PPS.
i8094MF_FIXED_MOVE(cardNo, AXIS_U, 10000);
//Set the fixed pulse moving command to 10000 Pulses.
//Set the new speed of U-axis after even activation to 100 PPS.
while (i8094MF_STOP_WAIT(cardNo, AXIS_U) == NO)
{ //If the U-axis of the assigned card is not stop, keep looping
DoEvents();
};
//After the event occurred, following line can get latched position. long Vsb = i8094MF_GET_LATCH(cardNo, AXIS_U);
//Ex2. When the EP value of U-axis exceeds
COMP+ (5,000),
//controller will move the Y-axis by 2,000 PPS.
i8094MF_SYNC_ACTION(cardNo, AXIS_U, 2, 0X0001, 1, 0, 3);
//Set the COMP+ of U-axis 5,000 and te compared source is real position (EP).
//Set the maximum speed of axesY and U to 9K PPS.
AXIS_YU,
//Set the Acc/Dec mode to be symmetric T-curve.
//Set the speed of axes Y and U to 3,000 PPS.
//Set the acceleration of axes Y and U to 200K PPS/S.
//Set the start speed of axes Y and U to 200 PPS.
i8094MF_SET_PRESET(cardNo, AXIS_Y, 2000);
//Set the fixed pulse drive of Y-axis to be 2,000 PPS when the activating
//event occurs.
i8094MF_FIXED_MOVE(cardNo, AXIS_U, 10000);
//Command the U-axis to move 10,000 Pulses and the synchronous action
//will happen after a while.
6.3.2 Setting the COMPARE value
z
void i8094MF_SET_COMPARE( BYTE cardNo, WORD
axis,
WORD
nSELECT,
WORD
nTYPE,
long data)
Description:
This function sets the values of COMPARE registers. Howerer, it will disable the functions of software limits.
Parameters:
cardNo: Module number
ICPDAS I-8094 Software User Manual
axis: Axis or axes (Please refer to Table 2-1)
nSELECT: Select the COMPARE register
0
Æ COMP+
1
Æ
nTYPE: Select the souece for comparison
0
Æ Position(P) = LP
1
Æ Position(P) = EP
data: Set the COMPARE value: -2,147,483,648 ~ +2,147,483,647
Return:
None
Example: i8094MF_SET_COMPARE(cardNo, AXIS_U, 0, 1, 5000);
//Set the comparison function for U-Axis.
//Set the compared source to be
EP; and
the COMP+ value to 5000.
ICPDAS I-8094 Software User Manual
6.3.3 Get the LATCH value
z
long i8094MF_GET_LATCH( BYTE cardNo, WORD axis)
Description:
This function gets the values from the LATCH register.
Parameters:
cardNo: Module number
axis: The axis can be either X, Y, Z, or U. Please refer to Table 2-1.
Return:
Value of the LATCH register: -2,147,483,648 ~ +2,147,483,647
Example: long data = i8094MF_GET_LATCH(1, AXIS_Y);
//Get the latched value which is from Y-axis of card 1.
6.3.4 Set the PRESET data for synchronous action
z
void i8094MF_SET_PRESET( BYTE cardNo, WORD
axis,
long data)
Description:
This function sets the PRESET value for synchronous action.
Parameters:
cardNo: Module number
axis: The axis can be either X, Y, Z, or U. Please refer to Table 2-1.
Return:
data: LP: -2,147,483,648 ~ +2,147,483,647
EP: -2,147,483,648 ~ +2,147,483,647
P : -2,147,483,648 ~ +2,147,483,647
V : Please refer to section 2.5.
None
Example:
Please refer to the examples in section 6.3.1.
ICPDAS I-8094 Software User Manual
6.4 Continuous Interpolation
Some continuous interpolation will (that need CPU resource)block the programe. When you use those API in real time thread, you must take care that.
If it is broken and stopped，please solve it refer in section 6.5.5 !
6.4.1 2-Axis Rectangular Motion
z
BYTE i8094MF_RECTANGLE(
BYTE cardNo, WORD axis1, WORD axis2,
WORD nAcc, WORD Sp, WORD nDir, long Lp, long Wp, long Rp,
DWORD RSV, DWORD RV, DWORD RA, DWORD RD)
Description:
Continuous interpolation will be performed to create a rectangular motion, which is formed by 4 lines and 4 arcs. The length of each side can be changed. The radius of each arc is the same and it can also be changed. The deceleration point will be calculated automatically. This is a command macro command that appears in various motion applications. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Please refer to Table 2-1.
The first axis and It can be either X, Y, Z, or U.
axs2: The second (axis 2). Please refer to Table 2-1.
The first axis and It can be either X, Y, Z, or U.
nAcc: 0
1
Æ symmetric T-curve Acc/Dec interpolation mode
Sp: Start point 0 ~ 7. (Sp0 ~ Sp7 are defined in the following
figure)
nDir: Direction movement
0: CCW; 1: CW
Lp: Length in Pulses (1 ~ 2,147,483,647)
Wp: Width in Pulses (1 ~ 2,147,483,647)
Rp: Radius of each in pulses (1 ~ 2,147,483,647)
RSV: Starting speed (in PPS)
RV: Vector speed (in PPS)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE() function to identify the error.
ICPDAS I-8094 Software User Manual
Example:
BYTE cardNo=1; //select module 1.
int sv=1000; //starting speed: 1000 PPS.
int v=10000; //vector speed: 10000 PPS.
int a=5000; //acceleration: 5000 PPS/Sec.
int d=5000; //deceleration: 5000 PPS/Sec.
i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 16000);
//set the maximum speed to 16000 PPS.
i8094MF_RECTANGLE(cardNo, AXIS_X, AXIS_Y, 1, 0, 0, 20000, 10000, 1000, sv, v, a, d);
//execute a rectangular motion on the XY plane
ICPDAS I-8094 Software User Manual
6.4.2 2-Axis Continuous Linear Interpolation
z
BYTE i8094MF_LINE_2D_INITIAL( BYTE cardNo, WORD axis1, WORD axis2,
DWORD VSV, DWORD VV, DWORD VA)
Description:
This function sets the necessary parameters for a 2-axis continuous linear interpolation using symmetric T-curve speed profile.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Please refer to Table 2-1.
The first axis and It can be either X, Y, Z, or U.
axis2: The second axis (axis 2). Please refer to Table 2-1.
The second axis and It can be either X, Y, Z, or U.
VSV: Starting speed (in PPS)
VV: Vector speed (in PPS)
Return:
None
Example:
i8094MF_LINE_2D_INITIAL(…);
//This function should be defined before the i8094MF_LINE_2D_CONTINUE()
//function is used. Please refer to the example of this function.
z
BYTE i8094MF_LINE_2D_CONTINUE( BYTE cardNo, WORD nType, long fp1, long fp2)
Description:
This function executes a 2-axis continuous linear interpolation. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
nType: 0: 2-axis linear continuous interpolation
1: end of 2-axis linear continuous interpolation
fp1: The assigned number of pulses for the axis 1 (in Pulses)
(-2,147,483,648 ~ +2,147,483,647)
fp2: The assigned number of pulses for the axis 2 (in Pulses)
Return:
YES An error has occurred.
ICPDAS I-8094 Software User Manual
Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example:
BYTE cardNo=1; //select module 1.
int sv=300; //starting speed: 300 PPS.
int v=18000; //vector speed: 18000 PPS.
long a=500000L; //acceleration: 500000 PPS/Sec.
int loop1; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU,160000L); i8094MF_LINE_2D_INITIAL(cardNo, AXIS_X, AXIS_Y, sv, v, a); for (loop1=0; loop1<10000; loop1++)
{ i8094MF_LINE_2D_CONTINUE(cardNo, 0, 100, 100); i8094MF_LINE_2D_CONTINUE(cardNo, 0, -100, -100);
} i8094MF_LINE_2D_CONTINUE(cardNo, 1, 100, 100);
ICPDAS I-8094 Software User Manual
6.4.3 3-Axis Continuous Linear Interpolation
z
BYTE i8094MF_LINE_3D_INITIAL( BYTE cardNo, WORD axis1, WORD axis2,
WORD axis3, DWORD VSV, DWORD VV, DWORD VA)
Description:
This function sets the necessary parameters for a 3-axis continuous linear interpolation using symmetric T-curve speed profile.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Please refer to Table 2-1.
The first axis and It can be either X, Y, Z, or U.
axis2: The second axis (axis 2). Please refer to Table 2-1.
The second axis and It can be either X, Y, Z, or U.
axis3: The third axis (axis 3). Please refer to Table 2-1.
The third axis and It can be either X, Y, Z, or U.
VSV: Starting speed (in PPS)
VV: Vector speed (in PPS)
Return:
None
Example: i8094MF_LINE_3D_INITIAL(…);
//This function should be defined before the i8094MF_LINE_3D_CONTINUE()
//function is used. Please refer to the example of this function.
ICPDAS I-8094 Software User Manual
z
BYTE i8094MF_LINE_3D_CONTINUE( BYTE cardNo, WORD nType, long fp1, long fp2, long fp3)
Description:
This function execute a 3-axis continuous linear interpolation. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
nType: 0: 3-axis linear continuous interpolation
1: end of 2-axis linear continuous interpolation
fp1: The assigned number of pulses for axis 1
fp2: The assigned number of pulses for axis 2
(-2,147,483,648 ~ +2,147,483,647)
fp3: The assigned number of pulses for axis 3
(-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred.
Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example:
BYTE cardNo=1; //select module 1.
int sv=300; int v=18000; //vector speed: 18000 PPS long a=500000L; //acceleration: 500000 PPS/Sec int loop1; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU,160000L); i8094MF_LINE_3D_INITIAL(cardNo, AXIS_X, AXIS_Y, sv, v, a); for (loop1=0; loop1<10000; loop1++)
{ i8094MF_LINE_3D_CONTINUE(cardNo, 0, 100, 100, 100); i8094MF_LINE_3D_CONTINUE(cardNo, 0, -100, -100, -100);
} i8094MF_LINE_3D_CONTINUE(cardNo, 1, 100, 100, 100);
ICPDAS I-8094 Software User Manual
6.4.4 Mixed Linear and Circular 2-axis motions in Continuous
Interpolation
z
void i8094MF_MIX_2D_INITIAL( BYTE cardNo, WORD axis1, WORD axis2,
WORD nAcc, DWORD VSV , DWORD VV , DWORD VA)
Description:
This function does the initial settings for mixed linear and circular 2-axis motions in continuous interpolation.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Please refer to Table 2-1.
The first axis and It can be either X, Y, Z, or U.
axis2: The second axis (axis 2). Please refer to Table 2-1.
1
Æ symmetric T-curve Acc/Dec (VSV、VV、VA)
VSV: Starting speed (in PPS)
VV: Vector speed (in PPS)
Return:
None
Example: i8094MF_MIX_2D_INITIAL(…);
//This function should be defined before the i8094MF_MIX_2D_CONTINUE()
//function is used. Please refer to the example of this function.
ICPDAS I-8094 Software User Manual
z
BYTE i8094MF_MIX_2D_CONTINUE( BYTE cardNo, WORD nAcc,
WORD nType, long cp1, long cp2, long fp1, long fp2)
Description:
This function executes mixed linear and circular 2-axis motion in continuous interpolation. However, it is a software macro-function; therefore, it requires
CPU resource to run this function.
Parameters:
cardNo: Module number
Æ continuous interpolation.
1
Æ it is the last command of this continuous interpolation. In
Acc/Dec mode, it will perform a deceleration stop. In constant speed mode, it will directly stop rather than decelerate.
nType:
1
Æi8094MF_LINE_2D(
BYTE cardNo, long fp1, long fp2);
2
Æi8094MF_ARC_CW(
BYTE cardNo, long cp1, long cp2, long fp1, long fp2);
3
Æi8094MF_ARC_CCW(
BYTE cardNo, long cp1, long cp2, long fp1, long fp2);
4
Æi8094MF_CIRCLE_CW(
BYTE cardNo, long cp1, long cp2);
5
Æi8094MF_CIRCLE_CCW(
BYTE cardNo, long cp1, long cp2);
cp1: It assigns the center point data at axis 1.
(-2,147,483,648 ~ +2,147,483,647)
cp2: It assigns the center point data at axis 2.
(-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
(-2,147,483,648 ~ +2,147,483,647)
fp1: The assigned number of pulses for axis 1
Return:
YES An error has occurred. Use the i8094MF_GET_ERROR_CODE () function to identify the error.
ICPDAS I-8094 Software User Manual
Example: cardNo=1; int sv=300; int v=18000; //vector speed: 18000 PPS long a=500000L; //acceleration: 500000 PPS/Sec unsigned short loop1; i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 160000L); i8094MF_MIX_2D_INITIAL(cardNo, AXIS_X, AXIS_Y, 1, sv, v, a); for (loop1 = 0; loop1 < 10000; loop1++)
{ i8094MF_MIX_2D_CONTINUE (cardNo, 0, 1, 0, 0, 100, 100); i8094MF_MIX_2D_CONTINUE (cardNo, 0, 2, 100, 0, 100, 100);
} i8094MF_MIX_2D_CONTINUE (cardNo, 1, 4, 100, 100, 0, 0);
ICPDAS I-8094 Software User Manual
6.4.5 Multi-Segment Continuous Interpolation (Using Array)
z
BYTE i8094MF_CONTINUE_INTP(
BYTE cardNo, WORD axis1, WORD axis2, WORD axis3,
WORD nAcc, DWORD VSV, DWORD VV, DWORD VA, DWORD VD,
BYTE nType[ ], long cp1[ ], long cp2[ ], long fp1[ ], long fp2[ ], long fp3[ ])
Description:
This function executes a multi-segment continuous interpolation. Those segments are stored in arrays declared in the arguments . The speed profile can be either a constant speed or a symmetric T-curve. The deceleration point will be calculated automatically. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Can be either X, Y, Z, or U axis.
Please refer to Table 2-1 for the axis definition.
axis2: The second axis (axis 2). Can be either X, Y, Z, or U axis.
axis3: The third axis (axis 3). Can be either X, Y, Z, or U axis.
nAcc: 0
1
Æ a symmetric T-curve interpolation. Please set VSV, VV, VA,
and VD.
VSV: The starting speed (in PPS)
VV: Interpolation vector speed (in PPS)
Acceleration PPS/Sec)
VD: Deceleration (in PPS/Sec)
nType[ ]: Maximum segment: 1024 (0 ~ 1023). It contains the interpolation commands defined as follows.
1
Æi8094MF_LINE_2D(
BYTE cardNo, long fp1, long
fp2);
2
Æi8094MF_ARC_CW(
BYTE cardNo, long cp1, long cp2, long fp1, long fp2);
3
Æi8094MF_ARC_CCW(
BYTE cardNo, long cp1, long cp2, long fp1, long fp2);
4
Æi8094MF_CIRCLE_CW(
BYTE cardNo, long cp1, long cp2);
5
Æi8094MF_CIRCLE_CCW(
BYTE cardNo, long cp1, long cp2);
6
Æi8094MF_LINE_3D(
BYTE cardNo, long fp1, long fp2, long fp3);
7
Æ It indicates the end of continuous interpolation.
cp1[ ]: It contains a list of segment center point data at axis 1.
(-2,147,483,648 ~ +2,147,483,647)
cp2[ ]: It contains a list of segment center point data at axis 2.
(-2,147,483,648 ~ +2,147,483,647)
fp1[ ]: This array contains a list of segment end point data at axis 1.
(-2,147,483,648 ~ +2,147,483,647)
fp2[ ]: This array contains a list of segment end point data at axis 2.
(-2,147,483,648 ~ +2,147,483,647)
ICPDAS I-8094 Software User Manual
fp3[ ]: This array contains a list of segment end point data at axis 3.
(-2,147,483,648 ~ +2,147,483,647)
(Note: The 2-axis and 3-axis motion commands can not be mixed together when applying commands. Please fill 0 for the cell values in the array if these cells are not used.)
Return:
YES An error has occurred. Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example:
BYTE cardNo=1; //select module 1.
int sv=100; //set the starting speed to 100 PPS.
int v=3000; //set the speed to 3000 PPS.
int a=2000; //set the acceleration to 2000 PPS/Sec.
in t d=2000; //set the deceleration to 2000 PPS/Sec.
i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the maximum speed to 20K PPS.
BYTE nType[10]= { 1, 2, 1, 2, 1,7,0,0,0,0}; long cp1[10]= { 0, 10000, 0, 0, 0,0,0,0,0,0}; long long long long cp2[10]= { 0, 0, 0,-10000, 0,0,0,0,0,0};
fp1[10]= { 10000, 10000, 1000, 10000,-31000,0,0,0,0,0};
fp2[10]= { 10000, 10000, 0,-10000,-10000,0,0,0,0,0}; fp3[10]= { 0, 0, 0, 0, 0,0,0,0,0,0};
//put data of the required segments in arrays. i8094MF_CONTIUNE_INTP( cardNo, AXIS_X, AXIS_Y, 0, 1, sv, v, a, d, nType, cp1, cp2, fp1, fp2, fp3);
//execute the 2-axis continuous interpolation.
//The deceleration point will be calculated automatically.
//For this example, the final position of this motion will return to the starting point.
ICPDAS I-8094 Software User Manual
6.4.6 3-Axis Helical Motion
z
BYTE i8094MF_HELIX_3D(
BYTE cardNo, WORD axis1, WORD axis2, WORD axis3, WORD nDir,
DWORD VV , long cp1, long cp2, long cycle, long pitch)
Description:
This function performs a 3-axis helical motion. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Can be X, Y, Z, or U axis.
Please refer to Table 2-1 for the axis definition.
Axis2: The second axis (axis 2). Can be either X, Y, Z, or U axis.
Axis3: The third axis (axis 3). Can be either X, Y, Z, or U axis.
1
Æ Move in a CCW direction.
VV: Vector speed (in PPS)
cp1: The value of center at axis 1
(-2,147,483,648 ~ +2,147,483,647)
cp2: The value of center at axis 2
(-2,147,483,648 ~ +2,147,483,647)
cycle: Number of cycles
pitch: Pitch per revolution (the advanced distance for each revolution) (-2,147,483,648 ~ +2,147,483,647)
Return:
YES An error has occurred. Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example:
BYTE cardNo=1; //select module 1.
//=============================================== i8094MF_SET_MAX_V(cardNo, AXIS_XYZU,160000L);
//set maximum speed for all axes to 16K PPS.
long v=50000;
//set vector speed to 50K PPS.
i8094MF_HELIX_3D(cardNo, AXIS_Y, AXIS_Z, AXIS_X, 1, v, 0, 1000, 5, -2000);
//the circular motion is on YZ plane, and the linear motion is
ICPDAS I-8094 Software User Manual
//along the X axis.
//=============================================== i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 160000L);
//set the maximum speed for all axes to 160K PPS.
long v=100000L;
//set vector speed to 100K PPS.
i8094MF_HELIX_3D(cardNo, AXIS_Y, AXIS_Z, AXIS_U, 1, v, 0, 25000, 50, 3600);
//the circular motion is on YZ plane, and the linear motion is along.
//the U axis.
ICPDAS I-8094 Software User Manual
6.4.7 2-Axis Ratio Motion
z
BYTE i8094MF_RATIO_INITIAL( BYTE cardNo, WORD axis1, WORD axis2,
DWORD SV , DWORD V , DWORD A, float ratio)
Description:
This function sets the Initial values for ratio motion (motion in ratio) using a symmetric T-curve speed profile. However, it is a software macro-function; therefore, it requires CPU resource to run this function.
Parameters:
cardNo: Module number
axis1: The first axis (axis 1). Can be either X, Y, Z, or U axis.
Please refer to Table 2-1 for the axis definition.
Axis2: The second axis (axis 2). Can be either X, Y, Z, or U axis.
SV: Set the value for the starting speed ( in PPS).
V: Set the value for the vector speed (in PPS).
A: Set the acceleration value (in PPS/Sec).
ratio: Set the ratio value between the two assigned axes.
Return:
None
Example: i8094MF_RATIO_INITIAL(…);
//Initial setting for i8094MF_RATIO_2D(…) function.
//Please refer to the example of i8094MF_RATIO_2D() function.
z
BYTE i8094MF_RATIO_2D( BYTE cardNo, WORD nType, long data, WORD nDir)
Description:
This function performs a two-axis ratio motion.
Parameters:
cardNo: Module number
nType: 0
1
Æ Declare the end of ratio motion.
data: The pulse number of axis1
(-2,147,483,648 ~ +2,147,483,647)
nDir: Direction of the second axis.
0: CW; 1: CCW
Return:
ICPDAS I-8094 Software User Manual
YES An error has occurred. Use the i8094MF_GET_ERROR_CODE () function to identify the error.
Example:
BYTE cardNo=1; //select module 1. int sv=300; //set starting speed to 300 PPS.
int v=18000; //set vector speed to 18000 PPS.
long a=500000L; //set acceleration value to 500K PPS/Sec.
int loop1, loop2; i8094MF_SET_MAX_V(cardNo, 0Xf,160000L);
//set maximum speed value to 18000 PPS.
i8094MF_RATIO_INITIAL(cardNo,AXIS_U, AXIS_X, sv, v, a, 0.36f);
//assign U axis as the axis 1 and X axis as the axis 2.
//The ratio is 0.36.
for (loop2 = 0; loop2 < 5; loop2++)
{ for (loop1 = 0; loop1 < 5; loop1++)
{
//perform the ratio motion in the CW direction.
//perform the ratio motion in the CCW direction.
}
} i8094MF_RATIO_2D(cardNo, 1, 7200, 0);
//End the ratio motion.
ICPDAS I-8094 Software User Manual
6.5 Set the Interrupt Factors
6.5.1 Set the Interrupt Factors
z
void i8094MF_INTFACTOR_ENABLE( BYTE cardNo, WORD axis,
WORD
nINT)
Description:
This function sets the interrupt factors
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Value Symbol Statement
Return:
None
Interrupt occurs when the value of logical / real position counter is larger than or equal to that of pre-configired with i8094MF_SET_COMPARE( )
(please refer to Section 6.3.2)
Interrupt occurs when the value of logical / real position counter is smaller than that of COMP- i8094MF_SET_COMPARE( ) (please refer to
Section 6.3.2)
Interrupt occurs when the value of logical / real position counter is smaller than that of COMP+ i8094MF_SET_COMPARE( ) (please refer to
Section 6.3.2)
Interrupt occurs when the value of logical / real position counter is larger than or equal to that of pre-configired with i8094MF_SET_COMPARE( )
(please refer to Section 6.3.2)
Interrupt occurs at the end of the constant speed output.
Interrupt occurs at the start of the constant speed
6 C-STA drive or begin of Acceleration Offset Pulse output.
ICPDAS I-8094 Software User Manual
Example:
//Interrupt event handle
HANDLE //IST handle
DWORD WINAPI i8094_ThreadFunction(LPVOID lParam); //IST function
BYTE CardNo=1;
//MFC button event: Create the thread and set the interrupt factor
{
DWORD dwThreadID = 0;
HWND hWnd = NULL;
//Create thread: i8094_ThreadFunction i8094_hThread = CreateThread(NULL, 0, i8094_ThreadFunction, hWnd, 0,
&dwThreadID); axis,
//Initialize the interrupt
hINTP=Slot_Register_Interrupt(Slot1);
//Set the interrupt factor: D-END
// 4-Axis fixed pulse drive while (i8094MF_STOP_WAIT(CardNo, 0xf) == NO)
{ //Wait for motion done
DoEvents();
Sleep(1);
}
}
//IST function
DWORD WINAPI i8094KW_ThreadFunction(LPVOID lParam)
{
{
//Wait the event object
WaitForSingleObject(hINTP, INFINITE);
switch(dwEvent)
ICPDAS I-8094 Software User Manual
{
//Get the interrupt event object successfully
//While the driving stop, clear the position counter
// …
//Other user codes in the IST
// …
//End of the interrupt
Slot_Interrupt_Done(Slot1);
//Get the interrupt status
//Disable the interrupt factor i8094MF_INTFACTOR_DISABLE(CardNo, AXIS_X);
//Close the interrupt
Slot_Interrupt_Close(Slot1);
break;
break;
break;
}
}
}
Note:
Please refer the three functions:
Slot_Register_Interrupt(BYTE Slot),
Slot_Interrupt_Done(BYTE Slot), Slot_Interrupt_Close(BYTE Slot) in the
WinConSDK of Wincon GM1(w-8331-GM1/w-8731-GM1).
ICPDAS I-8094 Software User Manual
6.5.2 Interrupt Disabled
z
void i8094MF_INTFACTOR_DISABLE( BYTE cardNo, WORD axis)
Description:
This function disables the interrupt factors
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example:
Please refer to 6.5.1
ICPDAS I-8094 Software User Manual
6.5.3 Read the Interrupt Occurrence
z
WORD i8094MF_GET_RR3( BYTE cardNo, WORD axis)
Description:
Read the RR3 register that reflects the occurrence of Interrupt.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
The content of RR3 register.
RR3 Value
說明
When the drive pulse is up (drive pulseis set
0x001 PULSE on the positive logical level)
Once the value o flogic / real position counter
0x002 P>=C- is larger than that of COMP- register
Once the value o flogic / real position counter
0x004 P<C- is smaller than that of COMP- register
Once the value o flogic / real position counter
0x008 P<C+ is smaller than that of COMP+ register
Once the value o flogic / real position counter
0x010 P>=C+ is larger than that of COMP+ register
Interrupt occurs at the end of the constant
Offset Pulse output.
Interrupt occurs at the start of the constant
0x080
Pulse output.
D-END Interrupt occurs when the driving is finished
Example: i8094MF_GET_RR3
(cardNo, AXIS_X);
//read the Interrupt status of AXIS_X
ICPDAS I-8094 Software User Manual
6.6 Other functions
6.6.1 Holding the Driving Command
z
void i8094MF_DRV_HOLD( BYTE cardNo, WORD axis)
Description:
This command is usually used when users desire to starti multi-axis driving simultaneously. When this command is issued, users may write other driving commands to the control card. All the driving commands will be held after i8094MF_DRV_HOLD() is issued, and these commands will be started once the i8094MF_DRV_START() is issued. However, if in driving, this command will not cause the driving to be stopped. But the next command will be held.
Parameters:
cardNo: Module number
axis: Axis or Axes (Please refer to Table 2-1 for the axis definition.)
Return:
None
Example:
Please refer to the example in section 6.5.2.
ICPDAS I-8094 Software User Manual
6.6.2 Release the Holding Status, and Start the Driving
z
void i8094MF_DRV_START( BYTE cardNo, WORD axis)
Description:
This command releases the holding status, and start the driving of the assigned axes immediately.
Parameters:
cardNo: Module number
axis: Axis or Axes (Please refer to Table 2-1 for the axis definition.)
Return:
None
Example:
BYTE cardNo=1; //select card 1. i8094MF_DRV_HOLD(cardNo, AXIS_XYU); //hold the driving command to XYU i8094MF_SET_MAX_V(cardNo, AXIS_U, 10000);
//set the maximum speed of U-axis to be 10K PPS. i8094MF_NORMAL_SPEED(cardNo, AXIS_U, 0);
//set the driving mode to be symmetric T-curve.
i8094MF_SET_V(cardNo, AXIS_U, 2000);
//set the speed of U-axis to 2,000 PPS. i8094MF_SET_A(cardNo, AXIS_U, 1000);
//set the acceleration of U-axis to 1,000 PPS/S.
i8094MF_SET_SV(cardNo, AXIS_U, 2000);
//set the starting speed to 2,000 PPS. i8094MF_SET_AO(cardNo, AXIS_U, 9);
// set the AO to 9 Pulses. i8094MF_SET_MAX_V(cardNo, AXIS_XY, 20000);
//set the maximum speed of X and Y axes to 20K PPS.
i8094MF_AXIS_ASSIGN(cardNo, AXIS_X, AXIS_Y, 0);
//set the X-axis as the axis 1 and Y-axis as the axis 2 for a 2-axis interpolation.
i8094MF_VECTOR_SPEED(cardNo, 0);
//set constant speed motion. Therefore, VSV=VV. Only VV is required.
i8094MF_SET_VV(cardNo, 5000);
//set the vector speed for card 1 to 5,000 PPS. i8094MF_FIXED_MOVE(cardNo, AXIS_U, 5000);
//command U-axis to move 5,000 Pulse. This command is be held.
i8094MF_LINE_2D(cardNo, 12000, 10000);
//command a linear interpolation motion on the XY planes. It is held, too. i8094MF_DRV_START(cardNo, AXIS_XYU);
//release the holding status. X,Y , and U axes will start to move simultaneously.
ICPDAS I-8094 Software User Manual
6.6.3 Waiting until the Motion Is Completed
z
BYTE i8094MF_STOP_WAIT( BYTE cardNo, WORD axis)
Description:
This function can be used to assign commands to be performed while waiting for all motion to be completed (stopped).
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
EXAMPLE:
BYTE cardNo=1; //select module 1 i8094MF_SET_MAX_V(cardNo, AXIS_XYZU, 20000);
//set the maximum speed of all axes on module 1 to 20K PPS. i8094MF_NORMAL_SPEED(cardNo, AXIS_XYZU, 0);
//set the speed profile of all axes on module 1 to be symmetric T-curve i8094MF_SET_V(cardNo, AXIS_XYZU, 2000);
//set the speed of all axes on module 1 to 2000 PPS.
i8094MF_SET_A(cardNo, AXIS_XYZU,1000);
//set the acceleration value of all axes on module 1 to 1000 PPS/S.
i8094MF_SET_SV(cardNo, AXIS_XYZU, 2000);
//set the start velocity of all axes on module 1 to 2000 PPS.
i8094MF_SET_AO(cardNo, AXIS_XYZU, 9);
//set the value of remaining offset pulses to 9 pulses.
i8094MF_FIXED_MOVE(cardNo, AXIS_XYZU, 10000);
// move all axes on module 1 for 10000 pulses. if (i8094MF_STOP_WAIT(cardNo, AXIS_X) == NO)
{
//perform some actions here if the X axis has not finished its
//motion.
}
ICPDAS I-8094 Software User Manual
6.6.4 Stopping the Axes
z
void i8094MF_STOP_SLOWLY( BYTE cardNo, WORD axis)
Description:
This function decelerates and finally stops the assigned axes slowly.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_STOP_SLOWLY(1, AXIS_XY);
//decelerate and stop the X and Y axes
z
void i8094MF_STOP_SUDDENLY( BYTE cardNo, WORD axis)
Description:
This function immediately stops the assigned axes.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_STOP_SUDDENLY(1, AXIS_ZU);
//immediately stop the Z and U axes.
ICPDAS I-8094 Software User Manual
z
void i8094MF_VSTOP_SLOWLY( BYTE cardNo)
Description:
This function stops interpolation motion of the assigned module in a decelerating way.
Parameters:
cardNo: Module number
Return:
None
Example: i8094MF_VSTOP_SLOWLY(1);
//stop the interpolation of card 1 in a decelerating way.
z
void i8094MF_VSTOP_SUDDENLY( BYTE cardNo)
Description:
This function stops interpolation motion of the assigned module immediately.
Parameters:
cardNo: Module number
Return:
None
Example: i8094MF_VSTOP_SUDDENLY(1);
// stop the interpolation of card 1 immediately.
z
void i8094MF_SSTOP_SLOWLY( BYTE cardNo, WORD axis)
Description:
Except for State-Control, This function provides the similar feature with i8094MF_STOP_SLOWLY(). Stop pulse output simply ( no ERROR_CODE 256 returned)
.
ICPDAS I-8094 Software User Manual
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_SSTOP_SLOWLY(1, AXIS_XY);
//decelerate and stop the X and Y axes
z
void i8094MF_SSTOP_SUDDENLY( BYTE cardNo, WORD axis)
Description:
Except for State-Control, This function provides the similar feature with i8094MF_STOP_ SUDDENLY (). Stop pulse output simply ( no ERROR_CODE
256 returned)
.
Parameters:
cardNo: Module number
axis: Axis or axes (Please refer to Table 2-1)
Return:
None
Example: i8094MF_SSTOP_SUDDENLY(1, AXIS_ZU);
//immediately stop the Z and U axes.
z
void i8094MF_SVSTOP_SLOWLY( BYTE cardNo)
Description:
Except for State-Control, This function provides the similar feature with i8094MF_ VSTOP_SLOWLY (). Stop pulse output simply ( no ERROR_CODE
256 returned)
.
Parameters:
cardNo: Module number
Return:
None
Example: i8094MF_SVSTOP_SLOWLY(1);
//stop the interpolation of card 1 in a decelerating way.
ICPDAS I-8094 Software User Manual
z
void i8094MF_SVSTOP_SUDDENLY( BYTE cardNo)
Description:
Except for State-Control, This function provides the similar feature with i8094MF_ VSTOP_ SUDDENLY (). Stop pulse output simply ( no
ERROR_CODE 256 returned)
.
Parameters:
cardNo: Module number
Return:
None
Example: i8094MF_SVSTOP_SUDDENLY(1);
// stop the interpolation of card 1 immediately.
ICPDAS I-8094 Software User Manual
6.6.5 Clear the Stop Status
z
void i8094MF_CLEAR_STOP( BYTE cardNo)
Description:
After using anyone of the stop functions mentioned in section 6.5.4, please solve the malfunction, then issue this function to clear the stop status.
Paramters:
cardNo: Module number
Return:
None
Example: i8094MF_VSTOP_SUDDENLY(1);
//command the card 1 to stop motion immediately. i8094MF_CLEAR_STOP(1);
//clear the error status of card 1.
6.6.6 End of Interpolation
z
void i8094MF_INTP_END( BYTE cardNo, WORD
type
)
Description:
1. If the current motion status is running a interpolation motion and you would like to issue a single axis motion or change the coordinate definition, you should call this function before the new command is issued.
2. You can redefine the MAX_V for each axis. In this way, you do not have to execute i8094MF_INTP_END() function.
Parameters:
cardNo: Module number
type: 0
1
Æ 3-axis interpolation
Return:
None
Example: i8094MF_INTP_END(1, 0); //declear the end of a 2-axis interpolation on card 1.
ICPDAS I-8094 Software User Manual
Advertisement
Key Features
- 4-axis control
- Macro functions for C++ programming
- Supports WinCon and I-8000 series PAC controllers
- Automatic Homing
- General Motion Control functions
- Continuous Interpolation
- FRnet functions for I-8094F
- Software Limits
- External Pulse Input driving
