G-448HD V02 OK
G-448HD
OPERATOR AND MAINTENANCE MANUAL
SPARE PARTS LISTS INCLUDED
SERIAL NUMBER : 1037388 & UP
Printed in Canada
One Year Limited Warranty
Effective April 25, 2005, MOTREC, Inc. (MOTREC) hereby warrants to the Original Retail Purchaser (Owner) that any of its
vehicles shall be free from any defect in materials for a period of 90 DAYS while in the possession of such Original Retail
Purchaser. This warranty IS NOT TRANSFERABLE to any subsequent Buyer.
The warranty period is extended to one year or one thousand (1,000) hours, which ever first occurs, on the electric motor,
differential (parts that bathe in oil) and the electronic speed controller. MOTREC makes no warranty or representation with
respect to the internal combustion engine, tires and batteries, since their respective manufacturers cover such parts.
Accessories (light, gage, horn, etc), electrical contacts (switch, solenoid, contactor, relay), diodes & fuses, belts & pulleys,
filters & spark plugs, lubricants, brake linings & shoes, brake drums & discs, seals, seats, trim and other items subject to
wear are not included in this warranty; nor is any item that in MOTREC sole opinion, shows evidence of neglect, misuse,
abuse, collision or alteration.
This warranty shall not apply to normal maintenance requirements as described in the User Manual, and to damages during
shipment. The latter is the carrier's responsibility. No compensation will be allowed for delays.
To initiate warranty coverage on any MOTREC vehicle, the Dealer must complete and return the “Sales/Installation Report”
to MOTREC within 30 days after delivery to the Original Retail Purchaser; or within 90 days after the delivery date to the
Dealer, which ever occurs first. Failure to follow these procedures will result in considering the warranty coverage effective
as of the shipment date from the factory.
The defective vehicle must be returned, at the Owner's expense, to an authorised MOTREC Dealer within 30 days after
failure. The Owner will not be charged for parts and labour required for warranty repairs, which must be performed by an
authorised MOTREC Dealer only. The vehicle will be returned at the owner’s expense. The Warranty Claim Forms must be
completed and returned with the defective part(s) to MOTREC within 30 days after repair was done. No compensation will be
allowed for damages caused by vehicle downtime.
It is the responsibility of the owner of the vehicle to make sure that the driver is properly trained and instructed in the safety
features and operation of the vehicle, including vehicle stability, as required by OSHA and ANSI-B56. Operators shall read,
understand and follow the safety and operating instructions in MOTREC Manual before driving the vehicle. Operators shall
not be permitted to drive the vehicle unless a complete and adequate training has been provided. Driving a vehicle
constitutes a hazard. The driver is responsible for the control of the vehicle while driving and must always evaluate and care
for all peculiar situations that he or she may meet while driving. The driver assumes the inherent hazards related to this
activity. The vehicle is designed for off-road use only. MOTREC disclaims any liability for incidental or consequential
damages, to include, but not be limited to, personal injury or property damage arising from vehicle misuse, lack of
maintenance or any defect in the vehicle.
It is the responsibility of the Owner of the vehicle to make sure that the service technicians are properly trained as required
by OSHA and ANSI-B56. Service technicians shall read, understand and follow instructions in the MOTREC manual before
servicing the vehicle. Only qualified and authorized personnel shall be permitted to maintain, repair, adjust and inspect the
vehicle.
MOTREC prohibits, and disclaims responsibility for, any vehicle modification altering the weight distribution and stability,
increasing the speed or affecting the safety of the vehicle. Such modifications can cause serious personal injury or property
damage for which MOTREC disclaims any responsibility.
For Owners that are located outside North America, the warranty period starts the date of shipment from the factory, and the
defective parts must be returned at the Owner's expense to MOTREC prior to warranty repair.
26/02/2008
Table of contents
TABLE OF CONTENTS
INSTRUCTIONS
SAFETY WARNINGS FOR OPERATORS
VEHICLE CONTROLS (HYDROSTATIC KUBOTA – G-448HD)
FUEL TANK
MAINTENANCE
SAFETY WARNINGS FOR SERVICE TECHNICIANS
DECALS AND LABELS
PREVENTIVE MAINTENANCE SCHEDULE - MOTREC I.C. UNITS
OIL GRADE CHART
HYDRAULIC & PARKING BRAKES
FRONT AXLE AND STEERING
HYDROSTATIC PUMP – PORTS AND ADJUSTING SCREWS
SPARE PARTS
BODY, CAB, SEATS, TIRE
HYDROSTATIC DRIVE, REAR AXLE AND SUSPENSION
BRAKE CONTROLS
FRONT AXLE, SUSPENSION, STEERING, DISC BRAKES
ENGINE MUFFLER & MOUNTING, KUBOTA ENGINE
ELECTRICAL DIAGRAM – KUBOTA DIESEL START / CHARGE CIRCUIT
ELECTRICAL DIAGRAM – KUBOTA DUAL FUEL START / CHARGE CIRCUIT
ELECTRICAL DIAGRAM – KUBOTA GAS START / CHARGE CIRCUIT
ELECTRICAL DIAGRAM – KUBOTA TRANSMISSION / ENGINE MANAGEMENT
ELECTRICAL DIAGRAM – KUBOTA ACCESSORIES
HYDRAULIC DIAGRAM
MOTREC ILLUSTRATED ACCESSORIES
-3-
4 5 6 6 8 9 10 11 12 13 14 15 16 17 18 19 20 22 24 25 26 27 28 31 34 Instructions
INSTRUCTIONS
-4-
Instructions
SAFETY WARNINGS FOR OPERATORS
FAILURE TO OBEY THE FOLLOWING SAFETY RULES MAY RESULT IN SEVERE INJURY.
It is the responsibility of the owner of this vehicle to train operators to ensure that they understand the operating
characteristics of this vehicle, including training in vehicle stability, and obey the following safety rules and
guidelines. Owner shall comply with OSHA and ANSI/ITSDF B56.8 & B56.9 Standards for vehicle use, safety rules,
operator training and certification. Do not drive this vehicle unless you are a certified operator.
•
Do not drive this vehicle under the influence of drugs or alcohol.
•
Do not drive this vehicle on public roads and highways. This vehicle is designed to be driven in buildings.
•
This vehicle can make sparks which can ignite inflammable materials. Never use the vehicle in hazardous areas
where there are inflammable materials, explosive dust or fumes in the air.
•
Never run the engine in a confined area and avoid inhaling engine poisonous fumes which contain CO.
•
Have your vehicle inspected regularly by trained personnel, and cease operation if a malfunction occurs.
•
Do not open motor compartment. Keep clear from moving, rotating(wheels, sheaves, etc) or lifting parts.
•
Keep clear from hot parts of exhaust system.
•
Never carry more passengers than number allowed for this vehicle. Wait until all occupants are seated and
holding on before moving. Always keep all body parts inside vehicle. Keep both hands on steering wheel.
•
Do not exceed the vehicle cargo load capacity and gross trailing weight capacity, rated for flat hard even surface.
Different operating conditions such as loose terrain or ramps reduce vehicle capacity.
•
Avoid loose, unbalanced or top-heavy loads to keep a good stability and prevent overturn. Do not load cargo that
can fall off the vehicle. Do not carry cargo that is longer, wider or higher than this vehicle.
•
Always depress slowly the accelerator for smooth acceleration. Avoid stunt driving or horseplay.
•
Avoid sharp turns, always slow down before turning, to prevent vehicle overturn or trailer jack knife. Vehicle is
more sensitive to overturn and jack knife when traveling on inclines or when carrying a heavy load.
•
Always drive straight up and down the face of an incline, never across the face, to prevent overturn and trailer
jack knife. Drive slower and start applying brakes sooner on inclines to adjust for longer stopping distance.
•
Use extra care and drive slowly in reverse, in congested areas or on wet or slippery ground.
•
Keep to the right under normal conditions. Maintain a safe distance from all objects.
•
Slow down and sound the horn when approaching a corner or other blind intersections.
•
Before leaving the vehicle, park on level ground flat surface, turn off all switches, set forward/reverse selector to
neutral, set parking brake, remove the key. Do not park the vehicle on an incline.
•
Use another driver to steer this vehicle while it is towed. Be sure the driver uses brakes when you slow or stop
the towing vehicle. Do not exceed 5 MPH or carry any passenger while towing this vehicle.
-5-
Instructions
VEHICLE CONTROLS (HYDROSTATIC KUBOTA – G-448HD)
It is the responsibility of the owner of this vehicle to ensure that the operator understands the operating
characteristics of this vehicle, and obeys the safety instructions in this manual and ANSI/ITSDF B56.8 & 9
Standards. Do not drive this vehicle unless you are a certified operator as required by OSHA.
Fuel Tank
The fuel tank is located on the right at the rear. Do not remove the fuel cap while the engine is running. Do not
fill the fuel tank to point of overflowing. Use clean, fresh, lead-free gasoline intended for automotive use. A
minimum of 85 octane is recommended. Do not mix oil with gasoline.
Engine Oil
Never open engine compartment while engine is running. Before checking engine oil, stop engine. Avoid
touching hot engine, muffler and exhaust parts.
Hydraulic oil tank
The hydraulic oil tank is located on the left at the rear. Do not remove the oil cap while the engine is running. Do
not fill the oil tank to point of overflowing. Use hydraulic oil meeting ISO VG-46
Oil sentry
When the red light on the instrument panel turns on, the engine oil pressure is too low, or engine temperature is
to high. Therefore, the engine must be serviced to avoid serious damage.
Horn button
The horn button is located on the steering column.
Park brake lever
To actuate the parking brake, depress the brake pedal and pull up the hand lever located between the front seats.
Never park on an incline. Always set the parking brake before leaving the vehicle.
Accelerator and brake pedals
The accelerator and brake pedals operate the same way as the pedals of an automobile. Depress the accelerator
pedal with the right foot to speed the vehicle up and release it to slow down. Depress the brake pedal with the
right foot to reduce the vehicle speed.
Forward/Reverse Selector
Shift only when the vehicle is not moving and engine is at idle speed. Before leaving the vehicle, set the
FWD/REV selector to NEUTRAL and set the parking brake.
Manual Choke
GAS ENGINE: before starting a cold engine, pull out the choke knob and depress the accelerator pedal halfway
to the floor; as the engine warms up, push the knob in until the engine responds properly.
LPG ENGINE: before starting the engine, pull out the choke and depress the accelerator pedal halfway to the
floor; while starting, after two seconds, push the knob halfway; as the engine warms up, push the knob in until
the engine responds properly.
Key switch / starter
Before starting set the FWD/REV shifter to NEUTRAL, set parking brake, check for visible damage, check
brake pedal. To avoid starter damage do not crank the engine continuously for more than 10 seconds at a time;
-6-
Instructions
wait 60 seconds before attempting to start again. Before moving check safety devices: reverse alarm, strobe
light, motion beeper and all other safety devices. Before leaving vehicle, set FWD/REV shifter to NEUTRAL,
set parking brake, remove key.
-7-
Maintenance
MAINTENANCE
-8-
Maintenance
SAFETY WARNINGS FOR SERVICE TECHNICIANS
FAILURE TO OBEY THE FOLLOWING SAFETY RULES MAIN RESULT IN SEVERE INJURY.
Owner shall comply with OSHA and ASME/ANSI B56.8 & B56.9 regulations for vehicle maintenance.
Only qualified and authorized personnel shall be permitted to maintain, repair, adjust and inspect carriers,
vehicles, tractors, and batteries.
Maintenance operations must be made by properly trained service technicians.
Before any maintenance work, park the vehicle on a flat level surface, set the shift lever to park, turn off all
the switches, remove the key, lift the wheels off the ground and secure with jack stands of adequate capacity.
Keep clear from moving parts such as tires, sheaves, drive shaft and engine.
Keep clear from hot parts of exhaust system.
Avoid increasing engine RPM and vehicle speed to prevent accident and severe injuries.
Follow the maintenance instructions applicable to the type of repair, maintenance, or service.
Always wear a face shield and gloves when working around batteries. Use insulated tools to avoid sparks
that can cause battery explosion and acid splashing. Use two counteracting tools, double-wrench technique,
when disconnecting or tightening terminals on the battery to avoid damaging battery posts.
Keep cables and wires clear from mechanical and rubbing action. Make sure cable covering is free from
cutting or visible damage.
Before replacing a fuse or circuit breaker, identify the cause of failure and repair.
Always ensure the integrity of the warning labels. If they suffered damage and are not readable, replace them
promptly. The following images depict the dashboard and general security warning labels:
-9-
Maintenance
DECALS AND LABELS
! CAUTION !
The images included in this section depict the decals/markings installed on the vehicle. It is of
the utmost importance that theses decals/markings remain unaltered and readable. Else, the
sticker or the part baring the marking has to be replaced.
Dashboard security warning label:
# 5100000002
General security warning label:
# 5100000001
When an emergency push button is
installed, this label is required (located
under push button): # 3109800006
When a disconnect handle is installed, this label
is required (located in front of handle):
# 4800012J
Respectively, key switch markings, forward/reverse selector markings and light switch marking:
# 266211
# 2819321003
- 10 -
# 1269004
Maintenance
PREVENTIVE MAINTENANCE SCHEDULE - MOTREC I.C. UNITS
! WARNING ! Read safety instructions before maintenance operations to avoid severe injury.
! WARNING ! Maintenance operations must be made by properly trained service technicians.
Follow OSHA and ANSI B56 regulations.
Change engine oil after first 8 hours of use.
S/N: _________________ Hour Meter reading: ________
ESTIMATED TIME (MINUTES)
SHIFT
100H
200 H 1000 H YEAR
DESCRIPTION
START
Stop engine, check engine oil level.
3
Check vehicle for visual damage
2
Examine floor around and beneath unit for signs of
2
transmission oil, differential oil, brake fluid leaks.
Turn steering, check for hard steering, excessive
1
free play, or unusual sound when turning.
Check accelerator for free & smooth movement.
2
Shift in neutral, before starting engine.
1
Check reverse alarm, horn, strobe light.
2
Check brake pedal travel and parking brake for
2
secure hold. Start slowly and check service brake.
Check tire pressure, see pressure rating on tire
5
Check transmission & hydraulic oil level, if appl.
5
Check radiator coolant level, if applicable.
2
Check master cylinder fluid level (DOT 3)
2
Check brake pedal travel
1
Turn front wheels straight, check steering play
1
Check parking brake, requires 10 lbs. force to apply
1
Check brake lines and drive for leaks
5
Check fuel pipe, hose, clamps for damage & leaks
5
Check radiator fan belt, CVT belt, if applicable
3
Service air filter, check intake pipe & clamps
5
Check muffler, exhaust pipe, clamps, spark arrester
5
Air cooled engines only, change engine oil
20(X)
Water-cooled engines only, change engine oil
X(20)
WARNING LABELS & MARKINGS
2
Inspect wheel bearings and king pins for play
8
Inspect steering suspension linkages & frame.
10
Check pedal & master cylinder linkages for wear
10
Check service brake linings and linkages for wear
15
Check Spark Plugs
20
Change Oil Filter
20
Change air filter
10
Clean radiators and engine shrouds
20
Lubricate the vehicle
5
Service fuel filter, LP vaporizer & regulator
20
Check engine valve clearance & seats
40
Check ignition wires, tighten all nuts and bolts
20
Change differential oil, transmission oil & filter
20
Clean & repack front hubs
20
Flush/change brake fluid
30
Flush/change radiator coolant, if applicable
30
TOTAL TIME (MINUTES)
15
60
120
120
60
PERIOD
- 11 -
CHECK
Maintenance
OIL GRADE CHART
Vehicle system
Oil grade
Note
KOHLER engine
Above +32°F
Below +32°F
10W-30
5W-30
KUBOTA engine
Above 77°F
+32°F to 77°F
Below +32°F
30 or 10W-30 or 10W-40
20 or 10W-30 or 10W-40
10W or 10W-30 or 10W-40
Hydrostatic transmission
ISO VG46
Brakes
DOT 3
DMVSS116 standard
- 12 -
Maintenance
HYDRAULIC & PARKING BRAKES
Revision 2008-02-06
DRUM BRAKES
Remove brake drums and check lining wear. Replace shoes and springs if the lining thickness is 1/16"
(2mm) or less. Turn the brake adjustment to reduce the clearance between lining and drum. Wheels must
turn free when the pedal is released.
DISC BRAKES
Check pad linings. Replace pads if lining thickness is 1/16" (2 mm) or less.
PARKING BRAKE
Replace cables and stoppers if cable play exceeds 1/8” (4mm).
Wheels and/or differential pinion must turn freely when the parking brake is released.
On pinion brake, use spacers at pad fixed ends to reduce space between pads and pulley to 1mm.
To install new cables and stoppers:
-insert the new cable through the hand lever end;
-pull the cable out from the brake assembly end;
-insert the stopper on the cable and leave a maximum play of 1mm;
-for a two-cable system, make sure that cable length is the same at hand lever end;
-tighten ¼-ncx3/4 grade-5 bolt in stopper at 8 LbFt (11NM) torque;
-cable must extend 1.5” (4cm) out of the cable stopper, cut cable excess.
Once cable play has been checked and/or adjusted, turn the knob on the brake lever until a force of 75 Lbs
or 34 kg is required on the handle to set the parking brake.
BRAKE PEDAL
If the brake pedal becomes soft or spongy, air may have entered the hydraulic system and the brake system
has to be bled:
1. fill the master cylinder with brake fluid (DOT-3);
2. bleed front callipers one at a time by having someone applying a steady pressure on the brake
pedal, and close the bleeder before allowing the brake pedal to return to up position;
3. fill the master cylinder with brake fluid (DOT-3);
4. bleed rear wheel brakes one at a time, following the same procedure;
5. fill the master cylinder with brake fluid (DOT-3);
6. clean every fitting and line, remove traces of oil;
7. apply a continuous pressure on the brake pedal for about five minutes ;
8. Finally, inspect brake lines and fittings for leaks ;
- 13 -
Maintenance
FRONT AXLE AND STEERING
! CAUTION !
Before maintenance, turn off all switches, set to neutral, set parking brake, remove the key,
and raise the front end of the vehicle supporting it with two jack stands of adequate capacity
STEERING INSPECTION
− Check tire inflation pressure, suspension components, tie rods straightness, tie rod ends play
(wear), play (wear) in wheel bearings, kingpins and bushings.
REPLACING & ADJUSTING THE STEERING GEAR
− Remove the pitman arm;
− The steering box makes 6.5 turns, center the steering gear (3.25 turns from either side);
− Align the front wheel straight. Install the pitman arm.
TOE-IN ADJUSTEMENT
− With the wheels in straight forward direction, measure the inside (left to right) distance between
the front tires, at the front and rear of the tires;
− Turn the rear tie rod until the distances are equal and tighten the two lock nuts on the tie rod.
REMOVING & GREASING OF FRONT HUBS, required once-a-year
− Remove dust cap and cutter pin, unscrew nut, remove hub;
− Inspect bearings and races for wear and replace worn bearings;
− Replace the seal;
− Pack the hub with wheel bearing grease and re-assemble.
ADJUSTING FRONT HUBS
− Tighten spindle nut to 30 ft-lb to seat the bearing and back off the nut to the next slot;
− Install a new cutter pin and the dust cap.
- 14 -
Maintenance
HYDROSTATIC PUMP – PORTS AND ADJUSTING SCREWS
1
MACHINE RPM START-UP
ADJUSTING SCREW
Turn CW to increase RPM
2
POWER LIMITER
ADJUSTING SCREW
Turn CW to increase power
3
MINIMUM CHARGE PRESSURE
ADJUSTING SCREW
Turn CW to increase pressure
4
CHARGE PRESSURE
ADJUSTING SCREW
Turn CW to increase pressure
P1
CHARGE PRESSURE INTAKE
M1 HIGH PRESSURE SIDE A
M2 HIGH PRESSURE SIDE B
- 15 -
Spare Parts
SPARE PARTS
- 16 -
Spare Parts
BODY, CAB, SEATS, TIRE
REF
DESCRIPTION
1 BUCKET SEAT ON
SLIDE ADJUSTERS
2 LEFT ENGINE COVER
RIGHT ENGINE COVER
LPG TANK HOLDER
3 5-B, 18” OD, LUG, SOLID WHEEL
4 FRONT BUMPER
5 MOTOR COMP. GRID
6 STEEL CAB AND DOORS1
STEEL CAB1
RIGHT DOOR
LEFT DOOR
DOOR GLASS LEFT
DOOR GLASS RIGHT
PADDLE LATCH
PART #
REF DESCRIPTION
1005003
CATCH
HANDLE
OPENING HANDLE
OPENING BAR
RIGHT HINGES
LEFT HINGES
REAR VIEW MIRROR
SIDE MIRROR
MIRROR BRACKET FIXE
MIRROR BRACKET FOLDING
WIPER KIT
WIPER MOTOR 12V
ARM
WIPER
*
*
2391501001
2223360001
2314320001
2819449001
2360321002
2360320001
2360320014
2360320015
2367320001
2367320002
2803000003
* Contact manufacturer
1
With A/C, see addendum
- 17 -
PART #
3602024
2366320001
2366320003
2366320004
2365000001
2365000002
480039
480040
2399300014
2399300009
366211K
3113000001
2800000001
2800000002
Spare Parts
HYDROSTATIC DRIVE, REAR AXLE AND SUSPENSION
REF. PART NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DESCRIPTION
481433
5007001
DISC
SPACER
COTTERPIN
2910322001 CASTELLATED HUB NUT
2224322001 HUB
2820007
STUD ½ NF X 1 3/4
BOLT ½ NF X 2 ½
LOCK WASHER ½
CALL FACT. HYDRAULIC MOTOR
5016002
RIGHT CALIPER
5016003
LEFT CALIPER
5016004
L/R PAD SET
NUT ½ NF
LOCKWASHER ½
2177322006 48” HOUSING
BOLT 5/8-NC X 3 ½
362606
SHACKLE LINK
NUT 5/8-NC
LOCKWASHER
5040003
LEAF SPRING
BOLT ½ NF X 9 ½
2185322001 MOUNTING PLATE
- 18 -
Spare Parts
BRAKE CONTROLS
REF PART NO
DESCRIPTION
QTY
REF
PART NO
1
5
6
7
8
9
10
11
12
RUBBER
SPRING
LEVER
PIVOT
LUBRICATING FITTING
CLEVIS PIN 3/8 X 1
YOKE
MASTER CYLINDER
BOLT 3/8-NC X 3
1
1
1
2
1
1
1
1
2
14
15
6685001
ACCELERATOR PEDAL
CALL FACT. ACCELERATOR CABLE
1
1
30
31
32
33
3616013
2129000003
5016001
2130330001
1
2
2
2
242800
242816
2131501001
262807
242817
122813
362805
- 19 -
DESCRIPTION
8 in. HANDBRAKE LEVER
CABLE
CABLE STOP
CABLE RETAINER
QTY
Spare Parts
FRONT AXLE, SUSPENSION, STEERING, DISC BRAKES
- 20 -
Spare Parts
REF
PART NO
DESCRIPTION
REF
1
2
3
4
5
6
7
8
9
2208240001
2910000022
2208240002
2910000023
2104300004
2100300002
2100300003
2200300002
2207000001
2207000002
2910000005
2910000006
2207320001
2207300006
2201360002
2201662002
2201360001
2201662003
2201320001
2201448009
2205250001
2910300001
2103250001
2914364001
2229300002
2103300001
2224300001
2910300003
2103300002
2229300001
481431
481430
2134000001
2120236001
2916000001
2192280001
STEERING WHEEL
NUT 3/4-16
COVER
PIN
OIL SEAL
BUSHING
BUSHING
TUBE
ROD END, LEFT HAND
ROD END, RIGHT HAND
NUT, LEFT HAND
NUT, RIGHT HAND
FRONT TIE ROD
TIE ROD
RIGHT AXLE
31
32
33
34
35
36
37
10
11
11A
12
13
14
15
16
17
19
20
21
22
23
24
25
26
27
28
29
30
RIGHT AXLE , P. STEERING
LEFT AXLE
LEFT AXLE, P. STEERING
AXLE BEAM
AXLE BEAM, P. STEERING
KING PIN
NUT 3/4-NF
THRUST BEARING
BUSHING
OIL SEAL
TAPER BEARING
HUB
WHEEL BOLT
TAPER BEARING
DUST CAP
RIGHT CALIPER
LEFT CALIPER
FLEX. HOSE
DISC
U-BOLT
LEAF SPRINGS
NUT 1/2-NF
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
- 21 -
PART NO
2182320001
2183240002
2180240001
2184448001
2910000017
2910000018
2139000003
2139000002
2200300003
2910000024
2117250001
4430002
2207320009
2910000020
2910000021
2128280001
2206300003
2910300002
2121000005
2121000006
2330014
2330013
2230014
2330015
2200224003
2200224001
2200224002
4430001
2910000024
2392224001
2206224001
2230016
2230017
DESCRIPTION
BOLT 5/8-NC
SHACKLE LINK
BUSHING
NUT 5/8-NC
SHOCK ABSORBER
PLATE
BOLT, LONG
BOLT, SHORT
BOLT
WASHER
SHAFT
SCREW
GEAR
GEAR FOR TILT/TEL. STEERING
ARM
BOLT 7/16-NC
LOCK WASHER
NUT
PADS
STEERING SUPPORT
CASTELLATED NUT
BUSHING, LONG
BUSHING, SHORT
HORN COVER
STEERING WHEEL
ADJUSTABLE COLUMN
UNIVERSAL JOINT
SHAFT
NYLON COUPLER
SHAFT
UNIVERSAL JOINT
SCREW
SELECTOR BOX
COLUMN MOUNTING PLATE
NYLON WASHER
NYLON BUSHING
Spare Parts
ENGINE MUFFLER & MOUNTING, KUBOTA ENGINE
- 22 -
Spare Parts
REF PART NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
2169501036
2169449004
2169661018
2169501027
2819449004
3129501004
246101
2160501006*
2160501002
2150449001
2150449002
2150449003
2157501011
2157501012
2169501030
2169501039
2169501040
2169501041
2157661001
4160322001
2169501034
2169501033
2604501002
2169501026
2169449001
2169449010
2913501002
2169501035
2169449005
consult manuf.
DESCRIPTION
RADIATOR
RADIATOR SUPPORT
AIR DEFLECTOR – TOP
AIR DEFLECTOR – BOTTOM
RADIATOR GRID
COOLING FAN
SOLENOID
ENGINE SUPPORT – FRONT
ENGINE SUPPORT – REAR
KUBOTA DUAL FUEL ENGINE KIT
KUBOTA GAS ENGINE KIT
KUBOTA DIESEL ENGINE KIT
90° EXHAUST
EXHAUST GASKET
AIR FILTER SUPPORT
ADAPTOR – MOTOR / PUMP
PUMP COUPLING
MOTOR COUPLING
CATALITIC MUFFLER
HYDROSTATIC PUMP
AIR CLEANER MOUNTING BAND
AIR CLEANER
RESERVE TANK – PRESTONE
RUBBER MOUNT MUFFLER
HEAT SHIELD
MUFFLER HOLDER
AIR INTAKE FLEXIBLE TUBE
INTAKE – AIR FILTER TUBE
AIR INTAKE TUBE
ENGINE RUBBER MOUNT
* WITH A/C, SEE ADDENDUM
- 23 -
Spare Parts
ELECTRICAL DIAGRAM – KUBOTA DIESEL START / CHARGE CIRCUIT
- 24 -
Spare Parts
ELECTRICAL DIAGRAM – KUBOTA DUAL FUEL START / CHARGE CIRCUIT
- 25 -
Spare Parts
ELECTRICAL DIAGRAM – KUBOTA GAS START / CHARGE CIRCUIT
- 26 -
Spare Parts
ELECTRICAL DIAGRAM – KUBOTA TRANSMISSION / ENGINE MANAGEMENT
- 27 -
Spare Parts
ELECTRICAL DIAGRAM – KUBOTA ACCESSORIES
- 28 -
Spare Parts
PARTS LIST
NO
DESIGNATION
A1
B1
B2
B3
B4
B5
B6
B7
B8
E1
E2
E3-E4
E5-E6
E7-E8
F1
F2-F3
F4
F5-F7
F8
ENGINE CONTROLLER
EMERGENCY TEMPERATURE SWITCH
EMERGENCY PRESSURE SWITCH
THERMOSTATIC SWITCH, RADIATOR
REVERSE ALARM
HORN
COOLANT TEMPERATURE SENDER
OIL PRESSURE SENDER
THERMOSTATIC SWITCH, OIL COOLER
GLOW PLUG TIMER
STROBE LIGHT
HEAD LAMP
SIDEMARKER LAMP
TAIL/BRAKE LIGHT
AGC FUSE HOLDER
IN-LINE FUSE HOLDER
CIRCUIT BREAKER
DIODE
MAXI FUSE HOLDER
MAXI BLADE FUSE 30A
ALTERNATOR
BATTERY
GLOW PLUG LAMP
CHARGE LAMP
EMERGENCY LAMP
RELAY 12V, F/R INTERRUPT
TIMER DELAY SW., SHUT DOWN
FLASHER RELAY
STARTER
ENGINE
RADIATOR FAN
CAB HEATER FAN
WIPER MOTOR
OIL COOLER FAN
CAB HEATER
VOLTMETER
FUEL GAUGE
TEMPERATURE GAUGE
OIL PRESSURE GAUGE
HOUR METER
GLOW PLUGS
FUEL SENDER
IGNITION SWITCH
FOR GAS / DUAL FUEL ENGINE
FOR DIESEL ENGINE
SEAT SWITCH
G1
G2
H1
H2
H3
K1
K2
K3
M1
M2
M3
M4
M5
M6
M7
P1
P2
P3
P4
P5
R1
R2
S1
S2
REF
- 29 -
3109449001
3109501001
3109501004
*
*
3108449004
3108501002
4190501004
*
*
*
*
5069005
3118321006
3107000001
367012
3118501006
3118501005
246212
246212
3069010
3129449001
3064004
3129501004
6690002
*
*
3069007
686203
3108449003
3108501003
3069008
686207
3109449002
3109501005
3109000003
QTY
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Spare Parts
S3
S4
S5
S6
S7
S8
S9
S10
Y1
Y2
Y3
Y4
Y5-Y6
Y7
Y8
Y9
Y10
X1
X2
X3
FORWARD/REVERSE SELECTOR
FREEWHEEL SWITCH
HEADLIGHT SWITCH
HORN BUTTON
BRAKE SWITCH
TURN SIGNAL SWITCH
CAB HEATER SWITCH
FUEL SELECTION MODE
FUEL PUMP
CARBURATOR FUEL VALVE
CARBURATOR LPG VALVE
LPG SHUT-OFF VALVE
FREEWHEEL VALVE
FREEWHEEL BLOCK KIT
HYDRAUSTATIC DISTRIBUTOR
COOLING FAN SOLENOID
DIESEL SOLENOID VALVE (ENGINE)
GLOW PLUG SOLENOID
ALTERNATOR CONNECTOR
FUEL VALVE CONNECTOR
GLOW PLUG TIMER CONNECTOR
- 30 -
266211
55017
1269004
*
246207
246050
55017
5069003
SV16-23
4110501003
246101
246101
-
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
Spare Parts
HYDRAULIC DIAGRAM
- 31 -
Spare Parts
- 32 -
Spare Parts
PARTS LIST
NO
A1
A2
R1
S1
S2
S3
S4
V1-V2
V4
M2-M3
M1
DESIGNATION
HYDROSTATIC PUMP
FREEWHEEL MANIFOLD
OIL COOLER
MACHINE START-UP ADJ. SCREW
POWER LIMITER ADJ. SCREW
CHARGE PRESSURE ADJ. SCREW
MIN. CHARGE PRESSURE ADJ. SCREW
FREEWHEEL SOLENOID
HYDROSTATIC VALVE
HYDRAULIC MOTOR
ENGINE
- 33 -
REF
5070014
4110501003
4190501003
QTY
1
1
1
SV16-23
2
Contact manuf.
-
2
1
Spare Parts
MOTREC ILLUSTRATED ACCESSORIES
Strobelight, polemount
Amber 12-80V: 3116000001
Red 12-80V:
2469001
Blue 12-80V:
3690008
Red Tail/Brake light
Housing:
3069012R
Bulb 12V:
3117240001
Headlight
Left:
Right:
Bulb H/L:
Bulb Turn:
Bulb Mark:
3111480003
3111480004
3117480001
3117480003
3117480002
Horn button VIP
2330014
Horn button, column mount
246210
Strobelight, cab mount
Amber 12-48V: 3116250001
Red 12-48V:
3069026
Blue 12-48V:
3069014
Amber 72-80V:3116720001
Red 72-80V: 3116720002
Blue 72-80V: 3116720003
Back-up lamp
Grommet:
12V:
24V:
Red Tail/Brake light
Grommet:
3269001
Plug:
246012A
12V :
2469021
24V :
2469022
246050
Horn button, dash mount
266210
Clear lamp
12V:
Bulb 12V:
Amber turn lamp
12V:
3069020
Bulb 12V:
3069021
Multi-LED amber turn lamp
Round Light: 3111000010
Grommet:
3111000008
Plug:
3111000009
Turn signal switch
3269001
3669012
3669012A
3069012
1269008
Pedestral head lamp
12V:
2569001
Bulb 12V:
2569001B
Bulb 24V:
4469001
Headlight
Left:
Right:
Bulb H/L:
Bulb Turn:
Bulb Mark:
3111480003
3111480004
3111480006
3111480008
3111480007
Multi-LED Red Tail/Brake
Light:
3111000006
Grommet:
3111000008
Plug:
3119000009
Horn button
3109250001
Limit switch
3030015
Multi-LED Back-up
Light:
3111000007
Strobe light: 3111000013
Grommet:
3111000008
Plug:
3119000009
Horn
12V:
24V:
Red Tail/Brake light
12V:
386002
- 34 -
246003
246013
Spare Parts
Analog Voltmeter
12V :
3069007
24V :
2469002
36-48V :
3669002
Wiper motor
12V:
24V:
Wiper arm
HOBBS Gauge
24V:
36V:
48V:
2469026
3069038
4869037
Wiper blade
14” Blade:
18” Blade:
3113000001
486211
2800000001
2800000002
2800000003
Pantograph wiper blade
246233
Headlamp 12V: 3111250002
Cab heater
12V:
36V:
48V:
3103300001
3669008
4869020
12V Dome light
3669006
Headlamp
12V:
Bulb 12V:
Red Pilot light
12V:
Bulb 12V:
3111300001
3111300002
246212
246212B
DC-DC converter, 10A
12-48V:
3069019
Pantograph wiper arm
246233A
12V Fan
DC-DC Converter, 25A
12-48V:
3124000002
72-80V:
3124880001
- 35 -
3669013
Back-up alarm or
Motion beeper
12-48V :
3100000001
72-80V :
3105720001
12-24V Adjustable:
3100000002
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement