Empire P)-1 Owner`s manual

Empire P)-1 Owner`s manual
EMPIRE
Comfort Systems
INSTALLATION INSTRUCTIONS
AND
OWNER’S MANUAL
LOFT FIREPLACE INSERT
DIRECT VENT
GAS FIREPLACE HEATER
MODEL SERIES
DVL25IN33(N,P)-1
DVL33IN33(N,P)-1
DVL25IN73(N,P)-1
DVL33IN73(N,P)-1
GAS-FIRED
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
UL FILE NO. MH30033
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage,
personal injury or loss of life.
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA only)
or mobile home, where not prohibited by state or local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
WARNING: If not installed, operated and maintained
in accordance with the manufacturer’s instructions,
this product could expose you to substances in fuel
or from fuel combustion which can cause death or
serious illness.
Page 1
TABLE OF CONTENTS
SECTIONPAGE
Important Safety Information............................................................................................... 3
Safety Information for Users of LP Gas.............................................................................. 4
Introduction......................................................................................................................... 5
Specifications...................................................................................................................... 6
Fireplace Insert Dimensions............................................................................................... 7
Mantle and Trim Clearances............................................................................................... 8
Gas Supply......................................................................................................................... 9
Venting and Installation................................................................................................10-12
Vertical Termination........................................................................................................... 13
Alternate ON/OFF Switch Installation............................................................................... 14
Surround Panel Installation............................................................................................... 15
Blower Accessory Information........................................................................................... 16
Glass Placement............................................................................................................... 17
Operating Instructions....................................................................................................... 18
Standing Pilot Lighting Instructions................................................................................... 19
Standing Pilot Wiring......................................................................................................... 20
Standing Pilot Troubleshooting......................................................................................... 21
IPI Electronic System Operating Instructions.................................................................... 22
IPI Electronic System Wiring Diagram.............................................................................. 23
Intermittent Pilot Lighting Instructions............................................................................... 24
Intermittent Control System Troubleshooting...............................................................25-27
Insert Maintenance and Service....................................................................................... 28
Decorative Accessories..................................................................................................... 29
Insert Parts View............................................................................................................... 30
Insert Parts List............................................................................................................30-31
Master Parts Distributor List.............................................................................................. 32
How To Order Repair Parts............................................................................................... 32
Appliance Service History............................................................................................33-35
Page 2
29209-0-0911
IMPORTANT SAFETY INFORMATION
Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.
DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED
DANGER: Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
•
Adequate accessibility clearances for servicing and
proper operation should be maintained.
WARNING: Indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
•
Under no circumstances should any solid fuels
(wood, coal, paper or cardboard etc.) be used in
this appliance.
•
Keep the area around your appliance clear of
combustible materials, gasoline and other flammable
vapor and liquids.
•
This appliance must not share or be connected
to a flue serving a separate solid-fuel burning
appliance.
•
The flow of combustion and ventilation air must not
be obstructed in any way.
CAUTION: Indicates a hazardous situation which, if
not avoided, could result in minor or moderate injury.
NOTICE: Addresses practices not related to personal
injury.
•
Children and adults should be alerted to the hazards
of high surface temperatures and should stay away
to avoid burns or clothing ignition.
•
Young children should be carefully supervised when
they are in the same room as the appliance.
•
Clothing or other flammable material should not be
placed on or near the appliance.
•
Due to high temperatures the appliance should be
located out of traffic and away from furniture and
draperies.
•
DO keep the appliance area clear and free from
combustible material, gasoline and other flammable
vapors and liquids.
•
The glass front or any part removed for servicing
the appliance must be replaced prior to operating
the appliance. Work should be done by a qualified
service person.
•
DO examine venting system periodically and replace
damaged parts.
•
DO make a periodic visual check of pilot and burners.
Clean and replace damaged parts.
•
CAUTION: The glass used in your fireplace insert is ceramic glass. If the glass is cracked or damaged
in any way, it should be replaced only with a complete
glass frame assembly from Empire. See parts list
on Pages 30-31 for ordering.
•
Keep burner and control compartment clean.
•
Vent cap is hot while fireplace is in operation.
•
Installation and repair should be done by a
QUALIFIED SERVICE PERSON. The appliance
should be inspected before use and at least annually
by a qualified service person. More frequent
cleaning may be required due to excessive lint from
carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulating
air passageways of the appliance be kept clean.
•
DO NOT use this fireplace insert if any part has been
under water. Immediately call a qualified service
technician to inspect the heater and to replace any
part of the control system and any gas control which
has been under water.
•
DO NOT put anything around the fireplace insert that will obstruct the flow of ventilation air.
•
•
Maintain clearances in accordance with local
installation codes and the requirements of the gas
supplier.
Any safety screen or guard removed for servicing
an appliance must be replaced prior to operating
the appliance.
29209-0-0911
Page 3
SAFETY INFORMATION FOR USERS OF LP GAS
Propane (LP-Gas) is a flammable gas which can cause fires
and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions which can protect both you and your family from an
accident. Read them carefully now, then review them point
by point with the members of your household. Someday
when there may not be a minute to lose, everyone’s safety
will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more
information, please contact your gas supplier.
LP-GAS WARNING ODOR
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.
That’s your signal to go into immediate action!
• Do not operate electric switches, light matches, use your phone.
Do not do anything that could ignite the gas.
• Get everyone out of the building, vehicle, trailer, or area. Do
that IMMEDIATELY.
• Close all gas tank or cylinder supply valves.
• LP-Gas is heavier than air and may settle in low areas such as
basements. When you have reason to suspect a gas leak, keep
out of basements and other low areas. Stay out until firefighters
declare them to be safe.
• Use your neighbor’s phone and call a trained LP-Gas service
person and the fire department. Even though you may not
continue to smell gas, do not turn on the gas again. Do not
re-enter the building, vehicle, trailer, or area.
• Finally, let the service man and firefighters check for escaped
gas. Have them air out the area before you return. Properly
trained LP-Gas service people should repair the leak, then
check and relight the gas appliance for you.
NO ODOR DETECTED - ODOR FADE
Some people cannot smell well. Some people cannot smell the
odor of the chemical put into the gas. You must find out if you
can smell the odorant in propane. Smoking can decrease your
ability to smell. Being around an odor for a time can affect your
sensitivity or ability to detect that odor. Sometimes other odors in
the area mask the gas odor. People may not smell the gas odor
or their minds are on something else. Thinking about smelling a
gas odor can make it easier to smell.
The odorant in LP-Gas is colorless, and it can fade under some
circumstances. For example, if there is an underground leak, the
movement of the gas through soil can filter the odorant. Odorants
in LP-Gas also are subject to oxidation. This fading can occur if
there is rust inside the storage tank or in iron gas pipes.
The odorant in escaped gas can adsorb or absorb onto or into walls,
masonry and other materials and fabrics in a room. That will take
some of the odorant out of the gas, reducing its odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity could
vary at different levels. Since it is heavier than air, there may be
more odor at lower levels. Always be sensitive to the slightest gas
odor. If you detect any odor, treat it as a serious leak. Immediately
go into action as instructed earlier.
SOME POINTS TO REMEMBER
• Learn to recognize the odor of LP-Gas. Your local LP-Gas
Dealer can give you a “Scratch and Sniff” pamphlet. Use it to
find out what the propane odor smells like. If you suspect that
your LP-Gas has a weak or abnormal odor, call your LP-Gas
Dealer.
• If you are not qualified, do not light pilot lights, perform service,
or make adjustments to appliances on the LP-Gas system. If
you are qualified, consciously think about the odor of LP-Gas
prior to and while lighting pilot lights or performing service or
making adjustments.
• Sometimes a basement or a closed-up house has a musty
smell that can cover up the LP-Gas odor. Do not try to light
pilot lights, perform service, or make adjustments in an area
where the conditions are such that you may not detect the odor
if there has been a leak of LP-Gas.
• Odor fade, due to oxidation by rust or adsorption on walls of
new cylinders and tanks, is possible. Therefore, people should
be particularly alert and careful when new tanks or cylinders
are placed in service. Odor fade can occur in new tanks, or
reinstalled old tanks, if they are filled and allowed to set too
long before refilling. Cylinders and tanks which have been out
of service for a time may develop internal rust which will cause
odor fade. If such conditions are suspected to exist, a periodic
Page 4
sniff test of the gas is advisable. If you have any question
about the gas odor, call your LP-Gas dealer. A periodic
sniff test of the LP-Gas is a good safety measure under
any condition.
• If, at any time, you do not smell the LP-Gas odorant and you
think you should, assume you have a leak. Then take the same
immediate action recommended above for the occasion when
you do detect the odorized LP-Gas.
• If you experience a complete “gas out,” (the container is under
no vapor pressure), turn the tank valve off immediately. If the
container valve is left on, the container may draw in some air
through openings such as pilot light orifices. If this occurs, some
new internal rusting could occur. If the valve is left open, then
treat the container as a new tank. Always be sure your container is under vapor pressure by turning it off at the container
before it goes completely empty or having it refilled before it is
completely empty.
29209-0-0911
INTRODUCTION
Instructions to Installer
1. Leave instruction manual with owner after installation.
2. Have owner fill out and mail registration card supplied with the
fireplace.
3. Show owner how to start and operate the fireplace.
This direct-vent gas fireplace heater is designed to operate with
all combustion air being siphoned from the outside of the building
and all exhaust gases expelled to the outside of the building. The
information contained in this manual pertains to all models and gas
control systems unless otherwise noted.
WARNING
This unit is not for use with solid fuels
Appliance Certification
This fireplace is design certified in accordance with American
National Standard/CSA Standard ANSI Z.21-88/CSA 2.33 and by
Underwriters Laboratories as a Direct Vent Gas Fireplace Heater
and shall be installed according to these instructions.
Consult your local building code agency, prior to installation, to ensure
compliance with local codes-including permits and inspections.
The fireplace insert, when installed, must be electrically grounded in
accordance with local codes or, in absence of local codes, with the
National Electric Code ANSI/NFPA 70 or Canadian Electric code,
CSA C22.1, if an external electrical source is utilized.
These models may be installed in a bedroom or bed-sitting room
in the U.S.A. and Canada.
Qualified Installing Agency
Installation and replacement of gas piping, gas utilization equipment
or accessories and repair and servicing of equipment shall be
performed only by a qualified agency. The term “qualified agency”
means any individual, firm, corporation or company which either in
person or through a representative is engaged in and is responsible for
(a) the installation or replacement of gas piping or (b) the connection,
installation, repair or servicing of equipment, who is experienced in
such work, familiar with all precautions required and has complied
with all the requirements of the authority having jurisdiction.
State of Massachusetts: The installation must be made by
a licensed plumber or gas fitter in the Commonwealth of
Massachusetts.
The installation must conform with local codes or, in the absence of
local codes, with the National Fuel Gas Code ANSI Z223.1/NFPA
54* Natural Gas and Propane Installation Code, or CSA B149.1 in
Canada. *Available from the American National Standards Institute,
Inc. 11 West 42nd St., New York, N.Y. 10036.
WARNING
ANY CHANGE TO THIS FIREPLACE OR ITS CONTROLS
CAN BE DANGEROUS.
Improper installation or use of the fireplace can cause
serious injury or death from fire, burns, explosions, or
carbon monoxide poisoning
shown in these instructions or use with a type of gas not
shown on the rating plate is the responsibility of the person
and company making the change.
Important
All correspondence should refer to complete Model Number, Serial
Number and type of gas.
High Altitude
When installing this unit at an elevation above 2000 feet (in the
United States) it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Generally,
input should be reduced 4 percent for each 1000 feet above sea
level. However, if the heating value of the gas has been reduced,
this general rule may not apply. Check with local gas utility for proper
orifice size identification.
Canadian High Altitude
Altitude: 0-4500 feet (0-1370 m)
When installing this unit at an elevation above 4500 feet (in Canada),
check with local authorities.
Consult your local gas utility for assistance in determining the proper
orifice for location.
Preparation
This direct vent gas fireplace insert and its components are tested
and safe when installed in accordance with this Installation Manual.
Report to your dealer any parts damaged in shipment, specifically
check glass condition. Do not install unit with damaged, incomplete,
or substitute parts. Read all instructions before starting installation
and follow these instructions carefully during installation to insure
maximum benefit and safety. Failure to follow them will void your
warranty and may present a fire hazard.
The warranty will be voided by, and the warranter disclaims any
responsibility for the following actions:
• Installation of any damaged fireplace insert or vent system
component.
• Modification of the fireplace insert or direct vent system.
• Installation other than as instructed by Empire Comfort Systems,
Inc.
• Improper positioning of the optional decorative glass or glass
door assembly.
• Installation and/or use of any component part not manufactured
or approved by manufacturer.
NOTICE: Prior to operating this unit, be sure to clean the
interior porcelain coated liner panels and glass door with a
soft clean cloth. Due to normal manufacturing processes,
fingerprints and excess sealing materials may be present and
should be removed. When cleaning, do not use abrasives.
Any alteration of the original design, installed other than as
29209-0-0911
Page 5
SPECIFICATIONS
DVL25IN(3,7)3L MODELS
LP
Nat
Input Btu/hr Maximum
20,000
20,000
Btu/hr Minimum
16,000
14,000
5.9
5.9
4.4
4.4
1.35mm
2.20mm
5/16”
CLOSED
KWH (Maximum)
(Minimum)
Orifice
Air Shutter Opening
LP
Nat
Input Btu/hr Maximum
DVL33IN(3,7)3L MODELS
27,000
27,000
Btu/hr Minimum
22,000
19,000
KWH (Maximum)
7.83
7.83
(Minimum)
6.5
5.51
1.55mm
#39 (.0995)
5/16”
3/32”
Orifice
Air Shutter Opening
Remote Control
Accessories
FRBC
Description
Vertical Vent Kit - 17 1/2’
DVVK3FV
Vertical Vent Kit - 25’
DVK35
Vent Extension Kit
Millivolt Battery Remote ON/OFF
FRBTC
Millivolt Battery Remote Thermostat
TRW
Millivolt WIRELESS Wall Thermostat
TMV
Millivolt Reed Switch Wall Thermostat
FWS-1
Surround Kits
Millivolt Wall Switch
Description
4 Sided Contemporary - Stainless Steel Top & Bottom,
Black Sides
S2562BLSS
Stainless Steel, Black, for use on DVL25IN
models
S3362BLSS
Stainless Steel, Black for use on DVL33IN
models
4 Sided Traditional Black
S2562BL
Black for use on DVL25IN models
S3362BL
Black for use on DVL33IN models
SH-1-BL
Venting Kits
DVKI
Description
Shroud (For fireplace openings up to 48” x 36” Requires surround.)
Contents
One piece of 35’ FlexVent (split for 17 1/2’ vent run), Round Cap, Flashing, connectors,
and clamps.
Recommended when installing to an existing round fireplace chimney pipe.
Two pieces of 25’ FlexVent, Rectangle Cap, Flashing, connectors, and clamps
Recommended when installing to a square or rectangular clay flue.
35’ flex vent extension section with 2 connectors and 4 clamps
NOTICE: When installing vent caps, special locally made flashings may be required to properly seal the vent system to the existing
chimney termination.
Page 6
29209-0-0911
FIREPLACE INSERT DIMENSIONS
•
When planning a fireplace insert installation, it’s necessary to
determine:
• The vent system configuration to be used.
• Gas supply piping.
Whether optional accessories - devices such as a wall switch
or remote control - are desired.
Electrical supply requirements for blower.
Proper opening size of fireplace required for installation of
the fireplace insert.
•
•
G
3”
INTAKE
3” DIA.
FLUE
3” DIA.
3”
3 3/4”
6”
F
K
J
2 3/8”
L
2 3/8”
I
F
1 5/8”
E
M
O
H
D
B
A
N
C
DV FIREPLACE INSERT DIMENSIONS (all dimensions in inches)
MODEL
A
B
C
D
E
F
DVL25IN
28
DVL33IN
31
G
H
I
J
16-1/2
15
10-1/2
25-1/4
19-1/2
16-1/2
13-1/2
28-1/4
K
12-3/4
17
18-5/16
27
6-7/8
14-1/4
18-3/4
21-5/16
30
8-3/8
L
M
N
O
9-1/4
20
22-1/4
40
22-1/2
10-3/4
21-1/2
25-1/4
43
25-1/2
Figure 1
Fireplace Opening Dimensional Information/Sizing
MINIMUM FIREPLACE OPENING DIMENSIONS (inches)
MODEL
NO.
HEIGHT
A*
FRONT
WIDTH
B
DEPTH
C
REAR
WIDTH
D
DVL25IN
18-3/8
27-1/2
12-3/4
17-1/4
DVL33IN
21-3/8
30-1/2
14-1/4
19
D
*NOTICE: If the fireplace lintel is wider than 8” (203mm), the
height of the fireplace opening must be increased a few inches to
allow for a gradual offset in the exhaust and/or intake vent pipes.
C
A
B
Figure 2
29209-0-0911
Page 7
MANTLE AND TRIM CLEARANCES
COMBUSTIBLE
MANTEL/TRIM AREA
12”
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
O
Q
R
S
T
V
8”
U
W
X
Z
Y
MINIMUM CLEARANCE TO PERPENDICULAR
COMBUSTIBLE SIDE-WALL
(FROM EDGE OF DOOR FRAME)
TOP OF INSERT
Figure 3
SURROUND PANELS
Distance from
Face of Fireplace
Height Above Top of Insert
A
10”
N
23”
B
9-1/4”
O
22”
C
8-3/4”
P
21”
D
8”
Q
20”
E
7-1/4”
R
19”
F
6-1/2”
S
18”
G
6”
T
17”
H
5-1/4”
U
16”
I
4-1/2”
V
15”
J
3-3/4”
W
14”
K
3”
X
13”
L
2-1/2”
Y
12”
M
1-3/4”
Z
11”
Figure 4
Combustible Material
No greeting cards, stockings or ornamentation of any type should
be placed on or attached to the fireplace. The flow of heat can
ignite combustibles.
Page 8
29209-0-0911
GAS SUPPLY
The gas pipeline can be brought in through the right or left side of
the appliance. The insert has a Flexline with shutoff valve located on
the right side when facing the unit. See Figures 5 and 6. Consult
the current National Fuel Gas Code, ANSI Z223.1 CAN/CGA-B149
(.1 or .2) installation code.
Recommended Gas Pipe Diameter
Pipe Length
Schedule 40 Pipe
Inside Diameter
Tubing, Type L
Outside Diameter
Nat.
L.P.
Nat.
L.P.
0-10ft
0-3m
1/2"
12.7mm
3/8"
9.5mm
1/2"
12.7mm
3/8"
9.5mm
11-40ft
4-12m
1/2"
12.7mm
1/2"
12.7mm
5/8"
15.9mm
1/2"
12.7mm
41-100ft
13-30m
1/2"
12.7mm
1/2"
12.7mm
3/4"
19mm
1/2"
12.7mm
101-150ft
31-46m
3/4"
19mm
1/2"
12.7mm
7/8"
22.2mm
3/4"
1.9 mm
NOTICE: Never use plastic pipe. Check to confirm whether your
local codes allow copper tubing or galvanized.
NOTICE: Since some municipalities have additional local codes, it is
always best to consult your local authority and installation code.
The use of the following gas connectors is recommended:
— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing
and Fittings.
— ANS Z21.45 Assembled Flexible Appliance Connectors of Other
Than All-Metal Construction
The above connectors may be used if acceptable by the authority
having jurisdiction. The state of Massachusetts requires that a flexible
appliance connector cannot exceed three feet in length.
Installing the Main Gas Cock
Each appliance should have its own manual gas cock.
A manual main gas cock should be located in the vicinity of the unit.
Where none exists, or where its size or location is not adequate,
contact your local authorized installer for installation or relocation.
Compounds used on threaded joints of gas piping shall be resistant
to the action of liquefied petroleum gases. The gas lines must be
checked for leaks by the installer. This should be done with a soap
solution watching for bubbles on all exposed connections, and if
unexposed, a pressure test should be made.
Never use an exposed flame to check for leaks. Appliance must
be disconnected from piping at inlet of control valve and pipe
capped or plugged for pressure test. Never pressure test with
appliance connected; control valve will sustain damage!
NOTICE: The millivolt gas controls are equipped with a captured
screw type pressure test point, therefore it is not necessary to
provide a 1/8" test point up stream of the control.
When using copper or flex connector use only approved fittings.
The appliance and it’s individual shut off valve must be disconnected
from supply piping system during any pressure testing of that system
at test pressures in excess of 1/2 psig (3.5kPa).
The appliance must be isolated from the gas supply piping system
by closing its individual manual shut off valve during any pressure
testing of the gas supply piping system at test pressures equal to
or less than 1/2 psig (3.5kPa).
Attention! If one of the procedures results in pressures in excess of
1/2 psig (14" w.c.) (3.5 kPa) on the fireplace gas valve, it will result
in a hazardous condition.
Checking Manifold Pressures
Both Propane and Natural gas valves have a built-in pressure
regulator in the gas valve. Natural gas models will have a manifold
pressure of approximately 3.5" w.c. (.871kPa) at the valve outlet
with the inlet pressure to the valve from a minimum of 4.5" w.c.
(1.120kPa) for the purpose of input adjustment to a maximum of
14.0" w.c. (3.484kPa). Propane gas models will have a manifold
pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet
with the inlet pressure to the valve from a minimum of 10.8" w.c.
(2.68kPa) for the purpose of input adjustment to a maximum of
14.0" w.c. (3.484kPa).
FRONT OF
INSERT
Figure 5
RIGHT SIDE OF INSERT
Gas Supply Pressure (inches w.c.)
Minimum
Normal
Maximum
Natural Gas
4.5"
7.0"
14.0"
LP (Propane)
10.8"
11.0"
14.0"
Manifold Pressure (inches w.c.)
GAS FLEX LINE WITH
SHUTOFF VALVE
(PROVIDED)
Figure 6
Normal (HI)
Natural Gas
3.5"
LP (Propane)
10.0"
29209-0-0911
Page 9
VENTING AND INSTALLATION
1. To begin, remove the glass door from the unit. Note: The glass
door assembly is secured to the firebox with two (2) spring
clamps at the top of the door, and two (2) spring clamps at
the bottom of the door. Check to make sure there is no hidden
damage to the unit. Take a minute and plan out the gas, venting and electrical route. It is best to start with the gas line first,
followed by the chimney liner and electrical supply requirements.
2. Minimum fireplace opening requirements are shown in
Figure 2 of this installation manual. The firebrick (refractory),
glass doors, screen rails, screen mesh and log grates can be
removed from a factory built fireplace in order to gain minimum gas insert opening requirements prior to installing the
gas fireplace insert.
3. This insert requires no hearth extensions. Combustible material on the floor may be installed up to the insert. Do not
obstruct the lower louver of the insert. The original fireplace
cannot be returned to solid fuel in this condition.
4. The metal floor of the solid fuel firebox may be removed to
facilitate the installation of the insert. CLEARANCE TO COMBUSTIBLE MATERIAL UNDER THE INSERT IS 1/4”. YOU
MUST USE THE LEVELING LEGS TO RAISE THE INSERT
A MINIMUM OF 1/4” IF THE INSERT IS TO SIT ON COMBUSTIBLE MATERIAL. The side walls and top structure of the
firebox may not be altered with the exception of removable
baffles and dampers. Smoke shields, shelves and baffles may
be removed if attached with mechanical fasteners. The original fireplace cannot be returned to solid fuel in this condition.
5. The original specified clearances of a factory-built fireplace must be maintained, with the exception of the hearth.
Clearances on a masonry fireplace must be maintained
at 12” from the opening for combustible projections over
1 1/2”. Clearances for combustible projections under
1 1/2” must be maintained at 6” from the opening per NFPA211.
Plan the surround size accordingly. A surround must be used
with the insert.
WARNING
Under no circumstance can combustible material be placed
behind the surround.
6. The insert surround is tested and approved with this gas insert and may cover existing air circulation vents or grills on the
solid fuel fireplace it is installed into. If the surround does not
cover the entire ventilation grill surface, the exposed grill area
should be left open.
NOTICE: Surround panel kits have been tested and approved
to cover existing air circulation vents or grills.
NOTICE: Cutting of sheet metal parts of a fireplace in order to
install the fireplace insert is prohibited.
WARNING
Only the surround as supplied may be used to cover integral grills on the solid fuel-burning fireplace. No other components such as shrouds, sheet metal plates, etc. may be
used to seal off vents.
Page 10
7. To assure top performance, safety and efficiency, inserts must
be installed with an approved flue liner as per CAN/CGA B-149
or National Fuel Code ANSI Z223 and these instructions.
NOTICE: The following statement is also provided on a separate label plate in the instruction packet. Prior to installation
of the fireplace insert, the installer must mechanically secure
this warning plate to the inside of the fireplace for future reference as required.
WARNING
The solid fuel fireplace has been converted for use with gas
only and cannot be used for burning wood or solid fuels unless all original parts have been replaced and the fireplace
has been reapproved by the authority having jurisdiction.
8. The solid fuel fireplace’s flue damper must be fully locked in
the open position or removed for installation of the gas fireplace insert.
9. The fireplace and fireplace chimney must be cleaned and in
good working order and constructed of noncombustible materials.
10. Make sure that all chimney cleanouts fit properly so air cannot
leak into the chimney.
11. Install the insert without the surround panels attached and
make all gas, venting, and electrical connections.
12. To complete the installation reinstall the glass door assembly,
then install the surround panel assembly. Please refer to instructions included with the surround panel kit.
WARNING
The glass door assembly must be secured with all four (4)
spring latches for proper operation of the fireplace insert.
Do NOT operate without the glass door installed.
CAUTION
Ensure there are no obstructions to side air passages of
decorative trim once installed on insert.
INSTALLING THE VENT SYSTEM
Vent System Installation Precautions
Before starting installation of vent kits, the installer should read
these instructions and the Vent Kit Instructions to ensure that a
proper vent installation is completed. Consult your local Building
Codes before beginning the Installation.
WARNING
THIS GAS INSERT AND VENT ASSEMBLY MUST BE
VENTED DIRECTLY TO THE OUTSIDE AND MUST NEVER BE
ATTACHED TO A CHIMNEY SERVING A SEPARATE SOLID
FUEL BURNING APPLIANCE. EACH GAS APPLIANCE
MUST USE A SEPARATE VENT SYSTEM. COMMON VENT
SYSTEMS ARE PROHIBITED.
29209-0-0911
VENTING AND INSTALLATION
Vent System Approvals
Figure 8 shows the vent termination caps and systems approved
for use with these models. Approved vent system terminations are
labeled for identification. 3-inch diameter listed flexible aluminum
or stainless steel gas vent is used for both the incoming combustion
air and exhaust vent pipes. NO OTHER VENTING SYSTEMS OR
COMPONENTS MAY BE USED. Detailed installation instructions
are included with each vent termination kit and should be used in
conjunction with this manual.
Horizontal Venting
The vent system on this model CANNOT be terminated
horizontally.
Vertical Venting
The inlet and exhaust vent pipes MUST be connected to the proper
collars on the unit AND to the termination cap or the unit will not
operate. The intake vent collar is identified by a stamped “I” on the
top collar sliding vent plate assembly.
WARNING
MAJOR U.S. BUILDING CODES SPECIFY MINIMUM
CHIMNEY AND/OR VENT HEIGHT ABOVE THE ROOF TOP.
THESE MINIMUM HEIGHTS ARE NECESSARY IN THE
INTEREST OF SAFETY. SEE FIGURES 8 THROUGH 10 FOR
MINIMUM HEIGHTS, PROVIDED THE TERMINATION CAP IS
AT LEAST 2-FEET FROM A VERTICAL WALL AND 2-FEET
BELOW A HORIZONTAL OVERHANG.
Note: This also pertains to vertical vent systems installed on the
outside of the building.
WARNING
THE EXHAUST PIPE MUST ONLY BE CONNECTED TO THE
EXHAUST STARTING COLLAR OF THE UNIT AND TO THE
EXHAUST COLLAR OF THE TERMINATION CAP.
THE INLET AIR PIPE MUST ONLY BE CONNECTED TO THE
INLET AIR STARTING COLLAR OF THE UNIT AND TO THE
INLET AIR COLLAR OF THE TERMINATION CAP. BOTH THE
INLET VENT AND THE FLUE VENT MUST BE CONNECTED
FROM THE INSERT TO THE VENT TERMINATION CAP.
Connecting the Vent Pipe
CAUTION
Sharp edges. Always use gloves when installing.
Install the 3-inch flexible vent pipes down through the chimney.
Attach the pipe-to-cap adaptor to the termination cap and the
top of the flexible vent pipe, then install the cap to the top of the
chimney.
Remove the vent slide plate assembly from the top of the insert.
See Figure 7. Trim off excess venting then attach and secure
the bottom ends of the flex pipes to the starting collars with the
adjustable band clamps provided. Slide the gas insert into place,
and position any excess flex vent pipe back up into the chimney.
Begin installation of the insert into the fireplace opening. Align the
vent slide plate assembly with the guides located on top of the
insert. Work the insert inch by inch into the fireplace cavity as you
pull forward on the vent slide plate assembly. Do not use excessive
force on the vent slide plate. Once the vent slide plate is close to
seating, install the vent bolt through the center hole of the insert
top flange, and into the vent slide plate nut. Using a wrench or
socket, tighten the bolt until the vent slide plate is seated forward
completely.
Positioning, Leveling, and Securing Insert
1. Place the insert into position.
NOTICE: The front flanges of the insert (without surround panels)
should be set at approximately 1”(inch) in front of the face of the
fireplace.
2. Level the insert from side to side and front to back.
3. If necessary, use the leveling bolts included in the instruction
pack. Screw the legs into the nuts installed in the bottom of
the insert. Turn legs in until insert is level.
CAUTION
TO AVOID DOWNDRAFTS AND/OR COLD AIR PROBLEMS,
IT IS RECOMMENDED TO SEAL OFF THE AREA BETWEEN
THE TERMINATION CAP AND THE TOP OF THE SOLIDFUEL CHIMNEY OPENING INTO WHICH THE VENT CAP
HAS BEEN INSTALLED.
NOTICE: The minimum vertical vent rise is 10 feet and the
maximum vertical vent rise is 35 feet. These dimensions are
measured from the starting collars of the unit to the end of the last
section of vent pipe. See Figure 8.
NOTICE: The damper of the masonry chimney may need to be
removed to allow installation of the flexible-vent pipe.
When installing into a zero clearance, factory built wood-burning
fireplace, the use of the DVKI Round Vertical Termination Kit should
allow you to mount the vent adaptor and cap to the exposed round
chimney pipe easily.
Figure 7
29209-0-0911
Page 11
VENTING AND INSTALLATION
RECTANGULAR
TERMINATION CAP
(DVVK3FV KIT)
ROUND
TERMINATION CAP
(DVKI KIT)
ROUND CO-LINEAR TO
CO-AXIAL ADAPTOR
INTAKE VENT
10’ MINIMUM
35’ MAXIMUM
FLUE EXHAUST VENT
VENT CLAMPS
OPTIONAL
LOW VOLTAGE
WIRES
BLOWER ACCESS
COVER PLATE
OPTIONAL ON/OFF
SWITCH LOCATION
BLOWER
POWER CORD
Figure 8
Page 12
29209-0-0911
VERTICAL TERMINATION
Determining Minimum Vent Height Above the Roof.
WARNING
Major U.S. building codes specify minimum chimney and/or
vent height above the roof top. These minimum heights are
necessary in the interest of safety. These specifications are
summarized in Figure 9.
Vertical Through the Roof Applications
The Gas Fireplace Insert has been approved for:
a) Vertical installations up to 35 feet in height (top of insert to
cap).
b) Two sets of 45 degree elbow offsets (bends in flexvent) within
the vertical installation. From 0 to a maximum of 8 ft. of vent
pipe can be used between elbows.
c) Wall straps must be used to support offset pipe every 4'.
This application will require that you first determine the roof pitch
and use the appropriate venting components.
ROOF PITCH
H (Min.)
Flat to 6/12
12" (305 mm)
6/12 to 7/12
15" (381 mm)
Over 7/12 to 8/12
18" (457 mm)
Over 8/12 to 16/12
24" (610 mm)
Over 16/12 to 21/12
36" (914 mm)
Figure 9
Note that for steep roof pitches, the vent height must be increased.
In high wind conditions, nearby trees, adjoining roof lines, steep
pitched roofs, and other similar factors can result in poor draft, or
down-drafting. In these cases, increasing the vent height may solve
this problem.
24"
MIN.
General Maintenance
Conduct an inspection of the venting system semi-annually.
Recommended areas to inspect are as follows:
1. Check areas of the venting system which are exposed to the
elements for corrosion. These will appear as rust spots or
streaks and, in extreme cases, holes. These components should
immediately be replaced.
2. Remove the cap and shine a flashlight down the vent. Remove
any bird nests or other foreign material.
3. Check for evidence of excessive condensate, such as water
droplets forming in the flex venting and subsequently dripping
out at joints or seams. Condensate can cause corrosion of caps,
pipe and fittings. It may be caused by having excessive lateral
runs, or having exterior portions of the system exposed to cold
weather.
4. Inspect joints to verify that no pipe sections or fittings have been
disturbed and, consequently, loosened. Also, check mechanical
supports, such as wall straps or plumbers’ tape for rigidity.
Tall Vent Heights
In some circumstances when venting vertically (20 to 30 feet), it
may require that the flue baffle vent door be opened to improve
performance. It is especially important during initial cold start-ups.
To adjust, rotate the vent door enough to encourage better draft for
improved combustion.
C
L
12" MIN.
24"
MIN.
FIREBOX
BAFFLE
FLUE
BAFFLE
VENT
Figure 10
When terminating the vent cap near an exterior wall or overhang,
maintain minimum clearances as shown in Figure 10.
Figure 11
29209-0-0911
Page 13
ALTERNATE ON/OFF SWITCH INSTALLATION
WIRING THE FIREPLACE
NOTICE: Electrical wiring must be installed by a licensed
electrician.
CAUTION
DISCONNECT REMOTE CONTROLS IF YOU ARE ABSENT
FOR EXTENDED TIME PERIODS. THIS WILL PREVENT ACCIDENTAL FIREPLACE OPERATION.
6. Attach the surround panel assembly to the insert. Hang the
surround panel assembly on the face of the insert and center
left to right. Swing the surround panel assembly inward until
the bottom magnets contact the insert body side flanges. This
secures the surround panel assembly to the insert without
screws.
Installation of Alternate Surround Panel ON/OFF Switch
An ON/OFF switch and wire assembly are provided. They are included in the instruction packet.
Do not cut wire or insulation on metal edges.
NOTICE: Refer to surround panel installation section on page
15 for additional information on attachment.
Contemporary Surrounds
1. Find the coiled low voltage wire assembly and ON/OFF switch
located in the instruction packet.
2a. Millivolt Units: Attach the flag terminal ends to the “TH/TP”
and “TH” terminals on the front terminal block of the gas valve.
See Figure 13.
2b. IP Units: Disconnect the (2) black wires from the green
and white wire connectors. Connect alternate On/Off switch
wires to the green and white wires as shown in Figure 13b.
Note: This bypasses the On/Off switch located on the unit’s
left hand side flange.
3. Run the low voltage alternate switch wires over to the right
or left surround panel. Then secure the wires with wire clips
provided. See Figure 12.
Right Side Installation
Left Side Installation
Figure 13a
DFC
ELECTRONIC
CONTROL
MODULE
WHITE
WIRE
GREEN
WIRE
NOTE: OTHER WIRING NOT SHOWN
FOR CLARITY PURPOSES ONLY
ALTERNATE ON/OFF SWITCH
(MOUNT IN LOWER LEFT CORNER
OF THE SURROUND PANEL)
Figure 13b
ON/OFF
SWITCH
ASSEMBLY
WIRING FROM
MILLIVOLT GAS
VALVE
ON/OFF
SWITCH
ASSEMBLY
Figure 12
Insert ON/OFF switch into side panel then attach wire assembly from valve terminals.
4. Remove the switch knockout on the side surround panel, then
install the ON/OFF switch. See Figure 11.
5. Connect the low voltage wires from the gas valve to the
ON/OFF switch.
Page 14
29209-0-0911
SURROUND PANEL INSTALLATION
INSTALLING THE TRIM SURROUNDS
Combustible materials MUST NEVER overlap onto the front face.
WARNING
WHEN FINISHING THE FIREPLACE INSERT, NEVER OBSTRUCT OR MODIFY THE AIR INLET/OUTLET LOUVERS
ON THE FIREPLACE INSERT IN ANY MANNER.
1” Ref.
Figure 14
NOTE: INSTALL SURROUND ASSEMBLY
SO THAT THE TOP PANEL FLANGE
SLIDE’S OVER THE TOP SHIELD
SURROUND ON THE INSERT
CENTER SURROUND LEFT TO RIGHT
ENGAGE SIDE PANEL
MAGNETS TO SIDE
FLANGES ON INSERT
(BACK SIDE)
SURROUND ASSEMBLY
Figure 15
29209-0-0911
Page 15
BLOWER ACCESSORY INFORMATION
The appliance, when installed must be electrically connected and grounded in accordance with local codes or,
in the absence of local codes, with the current CSA C22.1
Canadian Electrical Code.
U.S. Installations, follow local codes and the National
Electrical Code, ANSI/NFPA No. 70.
Should this blower require servicing, the power supply
must be disconnected. For rewiring of any replacement
components, refer to Figures 16 and 17 and the parts list
on pages 30-31.
BLOWER ACCESSORY
Operation
The fireplace insert is equipped with a factory installed blower
accessory that includes a fan control switch, plus a rheostat
(speed control).
The speed control knob is located in the lower compartment at the
right side of the insert.
From a cold start, the temperature activated fan control switch will
normally take 5-10 minutes to heat up and energize the blower.
Once the blower is energized, adjust the blower speed control as
desired.
When the insert is shut off, it may take 30-40 minutes for the
heated unit to dissipate (cool down) enough for the blower to shut
off automatically. NOTICE: The blower shut off times will vary on
blower speed and BTU input level setting control by adjustment of
the HI/LO knob located on the gas valve.
BLOWER ASSEMBLY
FAN CONTROL
SWITCH
MILLIVOLT
VALVE SHOWN
PIEZO IGNITOR
(MILLIVOLT ONLY)
FAN SPEED CONTROL
REMOTE/OFF/ON SWITCH
(MILLIVOLT ONLY)
Figure 16
Blower removal instructions
Servicing or removal of the blower system must be performed by
a qualified service person.
If the blower assembly must be replaced, the following steps are
recommended for removal:
1. Turn off gas and disconnect the electrical supply.
2. Remove the front surround panel assembly by pulling bottom
forward, then upward to detach.
3. Release the two (2) spring latches at the top and two (2) spring
latches at the bottom to remove the glass door assembly.
4. Remove decorative glass from burner cover if used.
5. Remove the 5/16” x 2-1/2” center bolt that retains the Vent
Slide plate assembly.
6. Remove the insert from the fireplace cavity by pulling forward
on the insert, and at the same time, sliding the vent plate
rearward until disengaged.
7. As the insert is moved outward, the gas line may need to be
disconnected at the insert shut off valve. If so, make sure the
main gas line is shut off that supplies gas to the insert.
8. Once the insert is pulled out, the blower assembly can be
removed by locating the (6) screws on the lower back of the
insert that retains the blower base plate.
9. When the screws are removed, gently pull the blower assembly
outward.
10. Disconnect the two ¼” wire terminals from the motor.
11. Remove the (4) screws that retain the blower assembly to the
base plate, and set blower aside.
12. Install the replacement blower, and re-install the insert by
reversing above steps.
Page 16
Figure 17
29209-0-0911
OPTIONAL DECORATIVE GLASS PLACEMENT
WARNING:
Failure to position the parts in accordance with
the diagrams and instructions below or failure
to use only parts specifically approved for use
with this heater may result in property damage
or personal injury.
NOTE: The DVL Fireplace Insert may be operated with or
without the Decorative glass accessory options. Follow the directions below should you choose to enhance your Loft Fireplace Insert with any one of the
available decorative glass options.
DECORATIVE GLASS ACCESSORY PLACEMENT
2. To install the Decorative Glass, cut off a corner of the plastic
bag and proceed to apply the glass to the rear shelf on the
Loft burner (area behind the burner). Apply only enough glass
to the Top Cover to cover the black metal surfaces. Do not
allow the glass to fall around the burner tube. See Figure 18.
Apply the remaining decorative glass to the front sloped
surface of the Top Cover. Start by placing the glass along the
front edge of the top cover, then gradually place the glass
up the sloped top until completely covered. Do not allow the
glass to fall around the burner tube. See Figure 19.
CAUTION: Glass must not be placed on the burner.
The Decorative Glass options are available in various colors and
package sizes. Choose the proper size kit for use with your particular Loft Fireplace Insert. See Page 29.
CAUTION: Use of gloves and eye protection is required while
applying the decorative glass.
INSTALLATION
1. Application of the Decorative Glass should only be
performed after the DVL Fireplace Insert has been fully
installed, secured and tested for leaks. If operating the burner
with a Remote Control, make sure all batteries are installed
and that the burner operates with the remote correctly.
DECORATIVE GLASS
Figure 19
GLASS MUST NOT BE PLACED ON TOP OF OR
NEXT TO BURNER. GLASS TO BE PLACED ONLY
TO THE OUTSIDE OF THE FLANGED OPENING.
Figure 18
Figure 20
29209-0-0911
Page 17
MILLIVOLT OPERATING INSTRUCTIONS
750 Millivolt System
The standing pilot (750 millivolt system) is a continuous burning pilot.
The pilot remains ON even when the main burner is OFF.
The OWNER should carefully read and follow these operating
instructions at all times. Lower the door assembly to view the gas
controls for the fireplace.
When you ignite the pilot, the thermopile produces millivolts (electrical
current) which energizes the magnet in the gas valve. After 30
seconds to 1 minute time period you can release the gas control
knob and the pilot will stay ON. Allow your pilot flame to operate an
additional one (1) to two (2) minutes before you turn the gas control
knob from the PILOT position to the ON position. This time period
allows the millivolts (electrical current) to build-up to a sufficient
level allowing the gas control to operate properly.
Initial Lighting
Upon completing the gas line or turning the gas valve on after it has
been in the “OFF” position, a small amount of air will be in the lines.
When first lighting the fireplace, it will take a few minutes for the
lines to purge themselves of this air. Once the purging is complete,
the fireplace will light and operate satisfactorily.
1. Follow the SAFETY and LIGHTING INSTRUCTIONS for standing
pilot controls found in this manual and on labels found in control
compartment behind the door assembly.
Subsequent lightings of the appliance will not require such purging
if the gas valve is not turned to “OFF.”
Pilot Flame (Figure 22)
The thermopile/thermocouple (standing pilot) tips should be covered
with flame.
WARNING
During the initial purging and subsequent lightings, never
allow the gas valve control knob to remain depressed in the
“pilot” position without pushing the piezo ignitor button at
least once every second.
2. During the operating season, leave the control valve knob in the
“ON” position. This will allow the pilot flame to remain lit. Turn
the burner flame on or off with the fireplace REMOTE/OFF/ON
switch, wall switch or remote controls.
NOTICE: The gas control valve allows you to increase or decrease
the height of the main burner flame. The control valve has a pressure
regulator with a knob as shown in Figure 21. Rotate the knob
clockwise to “HI” to increase the flame height and counterclockwise
to “LO” to decrease the flame height.
3. When the operating season is over, turn the REMOTE/OFF/ON
switch to “OFF” and the control valve to “OFF”. The system,
including the pilot light, will be shut down.
Figure 22
NOTICE: During initial cold start-ups, it is recommended that the
pilot be operated only for a period of 3 to 5 minutes (burner off)
in order to encourage proper draft in the flue vent. Refer to the
“Tall Vent Height” section on page 13 for additional information on
adjustment of the flue baffle vent door in order ro imporve cold
start-up conditions.
NOTICE: On Propane (LP) gas models, when the burner shuts off, a
small secondary flash may occur as the burner flame is extinguished.
This is a normal occurence with LP gas and does not affect the
performance or safety of the appliance.
Figure 21
Page 18
29209-0-0911
STANDING PILOT LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
• If you cannot reach your gas supplier, call the fire department.
B. Before lighting smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it; call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. 2.
3.
4.
5.
Stop! Read the safety information above.
Set REMOTE/OFF/ON switch to OFF.
Turn off all electric power to the appliance (if applicable).
Lower bottom louver assembly.
Push in gas control knob slightly and turn clockwise
to "OFF."
Note:Knob cannot be turned from "PILOT" to "OFF" unless
knob is pushed in slightly. Do not force.
6. Wait ten (10) minutes to clear out any gas. Then smell for gas,
including near the floor. If you then smell gas, STOP! Follow
"B" in the safety information above. If you do not smell gas,
go to the next step.
7. Find pilot - Follow metal tube from gas
control. The pilot is behind the burner
on the right side.
8. Turn gas control knob counterclockwise
to "PILOT."
9. Push in control knob all the way and hold in. Repeatedly push
the piezo ignitor button until the pilot is lit. Continue to hold the
control knob in the for about one (1) minute after the pilot is
lit. Release knob, and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 9.
• If the control knob does not pop up when released, STOP
and IMMEDIATELY call a qualified service technician or
gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician or
gas supplier.
10. Turn gas control knob counterclockwise
to "ON."
11. Close bottom louver assembly.
12. Turn on all electric power to the appliance (if applicable).
13. Set REMOTE/OFF/ON switch to desired setting.
TO TURN OFF GAS TO FIREPLACE
1. Set REMOTE/OFF/ON switch to OFF.
2. Turn off all electric power to the appliance if service is to be
performed (if applicable).
3. Lower bottom louver assembly.
29209-0-0911
4. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
5. Close bottom louver assembly.
Page 19
STANDING PILOT WIRING
For Standing Pilot Ignition Wiring
Optional Wall Switch
Appliance Requirements
Position the wall switch in the desired position on a wall. Run a
maximum of 25 feet (7.8m) or less length of 18 A.W.G. minimum
wire and connect it to the fireplace valve pigtails.
WARNING
DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL
VALVE OR THE APPLIANCE WILL MALFUNCTION AND THE
VALVE WILL BE DESTROYED.
WARNING
DO NOT CONNECT THE 110-120 VAC TO THE WALL SWITCH
OR THE CONTROL VALVE WILL BE DESTROYED.
WARNING
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN
SERVICING CONTROL. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER
OPERATION AFTER SERVICING.
STANDING PILOT WIRING DIAGRAM
REMOTE CONTROL RECEIVER
WIRING DIAGRAM
H
N
(OPTIONAL) THERMOSTAT
(FACULATIVE) THERMOSTAT
GAS VALVE
(OPTIONAL) WALL SWITCH
REMOTE/OFF/ON SWITCH
(OPTIONAL) REMOTE CONTROL RECEIVER
REMOTE/OFF/ON SWITCH
RED
GREEN
BLACK
GREEN
REMOTE
OFF
ON
THERMOPILE
IF ANY OF THE ORIGINAL WIRE
AS SUPPLIED WITH THIS UNIT
MUST BE REPLACED, IT MUST BE
REPLACED WITH NUMBER 18, 150°C
WIRE OR ITS EQUIVALENT.
GAS VALVE
THERMOCOUPLE
Page 20
29209-0-0911
STANDING PILOT TROUBLESHOOTING
With proper installation and maintenance, your new Direct Vent Gas Fireplace will provide years of trouble-free
service. If you do experience a problem, refer to the Trouble Shooting Guide below. This guide will assist a qualified
service person in the diagnosis of problems and the corrective action to be taken.
1. Spark ignitor will not light pilot after repeated triggering
of piezo ignitor button.
a. Defective ignitor (no spark electrode)
— Check for spark at electrode and pilot; if no spark and
electrode wire is properly connected, replace ignitor.
b. No gas or low gas pressure.
— Check remote shut off valves from fireplace. Usually
there is a valve near the main. There can be more than
one (1) valve between the fireplace and main.
— Low pressure can be caused by a variety of situations
such as a bent line, too narrow diameter of pipe, or low
line pressure. Consult with plumber or gas supplier.
c. No LP in tank.
— Check LP (propane) tank. Refill tank.
2. Pilot will not stay lit after carefully following lighting
instructions.
a. Defective thermocouple.
— Check that pilot flame impinges on thermocouple. Clean
and/or adjust pilot for maximum flame impingement.
— Ensure the thermocouple connection at the gas valve
is fully inserted and tight (hand tight plus 1/4 turn). Faulty
thermocouple if reading is below specified minimum of 15
millivolts.
— Disconnect the thermocouple from the valve, place one
millivolt meter lead wire on the end of the thermocouple
and the other millivolt meter lead wire on the thermocouple
copper wire. Start the pilot and hold the valve knob in. If
the millivolt reading is less than 15 millivolt, replace the
thermocouple.
b. Defective valve.
— If thermocouple is producing more than 15 millivolts,
replace faulty valve.
3. Pilot burning, no gas to burner, valve knob “ON”, REMOTE/
OFF/ON switch “ON.”
a. REMOTE/OFF/ON switch, wall switch, remote control or
wires defective.
— Check REMOTE/OFF/ON switch and wires for proper
connections. Place jumper wires across terminal at switch.
If burner comes on, replace defective switch. If OK, place
jumper wires across switch wires at gas valve-if burner
comes on, wires are faulty or connections are bad.
b. Thermopile may not be generating sufficient millivolts.
— If the pilot flame is not close enough physically to the
thermopile, adjust the pilot flame.
— Be sure the wire connections from the thermopile at
the gas valve terminals are tight and the thermopile is fully
inserted into the pilot bracket.
— Check the thermopile with a millivolt meter. Take the
reading at TH-TP & TP terminals of the gas valve. The
meter should read 350 millivolts minimum, while holding the
valve knob depressed in the PILOT position, with the pilot
lit, and the REMOTE/OFF/ON switch in the OFF position.
Replace the faulty thermopile if the reading is below the
specified minimum.
29209-0-0911
4.
5.
6.
7.
— With the pilot in the ON position, disconnect the thermopile
leads from the valve. Take a reading at the thermopile leads.
The reading should be 350 millivolts minimum. Replace
the thermopile if the reading is below the minimum.
c. Defective valve.
— Turn valve knob to ON. Place REMOTE/OFF/ON switch
to ON. Check with millivolt meter at thermopile terminals.
Millivolt meter should read greater than 200 millivolts. If
the reading is okay and the main burner does not ignite,
replace the gas valve.
d. Plugged main burner orifice.
— Check main burner orifice for blockage and remove.
Frequent pilot outage problem.
a. Pilot flame may be too high or too low, or blowing (high),
causing pilot safety to drop out.
— Clean and adjust flame for maximum flame impingement
on the thermocouple. Follow lighting instructions
carefully.
The pilot and main burner extinguish while in operation.
a. No LP (Propane) in tank.
Check LP (Propane) tank. Refill fuel tank.
b. Inner vent pipe leaking exhaust gases back into system.
— Check for leaks.
c. Glass too loose, gasket leaks in corners after usage.
— Be certain glass assembly is installed correctly.
d. Horizontal vent improperly pitched.
— The horizontal vent cap should slope down only enough
to prevent any water from entering the unit. The maximum
downwards slope is 1/4 inch.
e. Bad thermopile or thermocouple.
— Replace if necessary.
f. Improper vent cap installation.
— Check for proper installation and freedom from debris
or blockage.
Glass soots, and/or soot deposits collected internally.
a. Flame impingement on decorative glass.
— Check and adjust glass positioning. See Page 15.
Contact Empire Comfort Systems, Inc.
b. Debris around throat of main burner.
— Inspect the opening at the base of the main burner. It
is imperative that NO material be placed in this opening.
Flame burns blue and lifts off main burner.
a. Insufficient oxygen being supplied.
— Check to make sure vent cap is installed properly and
free of debris. Make sure that vent system joints are tight
and have no leaks.
— Check to make sure that no material has been placed
at the main burner base.
b. On taller vent heights (20-35 feet) it may help to open the
small flue baffle vent located directly above the pilot. This
will help maintain a positive vent draft and balance the
required combustion air flow.
Page 21
IPI ELECTRONIC SYSTEM OPERATING INSTRUCTIONS
Attention: For shipping purposes, the Electronic Control
Module and Receiver Plate assembly is loosely packaged
near the left side of the appliance. It is necessary that the receiver plate assembly be secured to the left front flange of the
appliance at the time of installation. To secure, remove the
two lower screws in the left side flange of the appliance, then
place the receiver plate assembly over the left front flange
and secure with the two screws previously removed. 1. Follow the SAFETY and LIGHTING INSTRUCTIONS for Intermittent Pilot controls found in this manual, and on labels
found in the control compartment located in the lower cavity
of the appliance.
2. During the operating season (or in power outage periods), it is
recommended that the pilot remain in the CPI (standing pilot
mode) to reduce cold start issues, and/or conserve battery
backup power during a power outage.
3. The gas valve has inlet and outlet pressure taps as shown in
Figure 23. Refer to page 9 for gas pressure requirements.
5.25 VDC ELECTRONIC CONTROL VALVE
The electronic control valve system includes the ability to switch
the pilot from a standing pilot mode to an intermittent pilot mode.
• IPI Mode - In the Intermittent Pilot mode, when the unit is
turned ON, it will cause spark to the pilot, light the pilot,
then allow the burner to light. When the unit is turned to
OFF, both the burner and pilot will be OFF.
• CPI Mode - In the Continuess Pilot mode, the pilot remains ON continuously even when the burner is turned
OFF.
Note: A small toggle switch is located on the receiver plate (left
side of unit) that is used to switch from IPI (upward position) to the
CPI (downward position). See Figure 23.
Note:
The gas control has a manual HI/LO flame adjustment
knob (regulator) that allows you to increase or decrease
the height of the burner flame. See Figure 23. Rotate
the HI/LO knob counterclockwise to “HI” to increase the
flame height, and clockwise to “LO” to decrease the flame
height.
OPTIONAL REMOTE CONTROLS
Optional remote controls are available for use with this appliance.
There is an area on the Receiver Plate (between the Electronic
Control module and the back-up battery pack) that the Remote
Receiver should be placed. A velcro pad is pre-attached to the
plate assembly for quick attachment of the remote receiver.
To connect the remote receiver to the appliance, first disconnect
the ON/OFF switch wires from the white and green wire connectors and connect the wires from the remote receiver to the green
and white wire connectors. See Figure 23.
Follow the instructions included with the remote control for programming and other operational information.
When the unit is turned to ON, the electrical current will energize
a spark to the pilot igniter. Once the pilot sensor heats up (after a
few seconds), the valve will be energized, allowing gas to flow to
the burner.
AC/DC Adapter
An AC/DC adapter is located in the Instruction Packet. To install,
connect the adapter to the mating female connector located near
the gas valve. Run the adapter plug out one of the side openings
of the insert in a similar manner as the blower power cord, then
plug the adapter into a 120V receptacle.
9 PIN CONNECTOR
SENSOR
IGNITOR
GROUND
DFC
ELECTRONIC
CONTROL
MODULE
SPARK ROD
RECEIVER PLATE
PILOT
SENSOR
OPTIONAL
REMOTE
CONTROL
RECEIVER
LOCATION
PILOT SELECTOR SWITCH
IPI - INTERMITANT PILOT (UP)
CPI - CONTINUOUS PILOT (DOWN)
PILOT
ASSEMBLY
IPI
GAS VALVE
CPI
AA (4)
BATTERY
BACKUP
MANUAL
HI/LO
REGULATOR
OUTLET
PRESSURE
TAP
INLET
PRESSURE
TAP
MANUAL ON/OFF OPERATIONAL SWITCH
NOTE: ADDITIONAL ON/OFF SWITCH & WIRING INCLUDED
TO INSTALL SWITCH TO SIDE OF SURROUND PANEL.
SEE PAGE 14.
Figure 23
Page 22
29209-0-0911
IPI ELECTRONIC SYSTEM WIRING DIAGRAM
BLUE
BLUE
WHITE
WHITE
GREEN
(
CPI/IPI
SWITCH
ORANGE
ON/OFF
SWITCH
REMOTE RECEIVER
OR
(OPTIONAL)
PILOT
YELLOW
WHITE
+ ON
REMOTE
- OFF
ORANGE
BLACK
WHITE
GAS CONTROL
VALVE
(GND)
WHITE
(
GREEN
(
BLACK
AC/DC
POWER ADAPTOR
RED
BATTERY
BLACK
BACK-UP
RED
ELECTRONIC
CONTROL MODULE
BATTERY HOLDER
If any of the original wire as supplied with this unit must be replaced, it must be replaced with equivalent gauge and temperature
rated wire.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently
located, manufactured (mobile) home where not prohibited by local codes. This appliance is not convertible for use with other gases,
unless a certified kit is used.
CAUTION: Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by
a licensed or qualified service person.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss
of life. Installation and service must be performed by a qualified installer, service agency or the gas supplier.
29209-0-0911
Page 23
INTERMITTENT PILOT LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. Before lighting smell all around the appliance area for gas. Be
sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it; call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Turn OFF electric power to the appliance.
3. Remove front surround panel assembly or bottom louver if
included.
4. Turn gas cock counterclockwise
to “On” position.
5. Wait ten (10) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow “B” in
the safety information above on this page. If you do not smell
gas, go to the next step.
6. Turn ON electric power to teh appliance.
7. Find pilot - Follow metal tube from gas control. The pilot is
behind the burner on the right side.
8. Turn main flame to on. If the pilot does not light within 60
seconds, stop and go to Step 5.
9. Refer to remote control instructions for detailed information,
control features, and operation. Note: There is a CPI/IPI switch
behind the right side panel that allows for a continuous standing
pilot mode or an intermittent pilot mode. See appliance manual
for location of this switch. If the pilot or burner does not stay
lit (in the standing pilot mode), stop and immediately call a
qualified service technician or gas supplier.
10. If the burner or pilot does not operate properly after several
tries, turn the gas cock clockwise
to “OFF” and call
your service technician or gas supplier.
11. Replace the front surround assembly or close bottom louver
assembly.
12. Operation of the gas valve is controlled by a manual on/
off switch or a hand held remote control. Refer to remote
instructions for detailed operation information.
GAS COCK
ELECTRODE
PILOT
FLAME
SENSOR
OFF
ON
TO TURN OFF GAS TO FIREPLACE
1. Set REMOTE/OFF/ON switch to OFF.
2. Turn off all electric power to the appliance if service is to be
performed (if applicable).
3. Lower bottom louver assembly.
Page 24
4. Push in gas control knob slightly and turn clockwise
to "OFF." Do not force.
5. Close bottom louver assembly.
29209-0-0911
INTERMITTENT CONTROL SYSTEM TROUBLESHOOTING
Brief Description of the Components
The gas valve is fitted with a manual HI/LO knob to allow for manual modulation of the gas outlet pressure to the appliance burner.
The controls are designed to be used with either LPG or Natural
Gas and can be converted by use of an OEM supplied conversion
kit.
The Digital Fireplace Control (DFC) is an automatic gas ignition
system based on a single microcontroller core. This control manages all functions related to ignition, flame sensing and supervision for atmospheric applications.
The DFC can be set to provide continuous or intermittent ignition
control sequences and flame monitoring with safety shutdown in
case of failure.
The DFC is set up as a stand alone (AC powered system with
battery back up. See Lighting Instructions on page 24 and Wiring
Diagram on page 23.
Troubleshooting
Before proceeding with the procedures in the following troubleshooting table, verify that the power supply (AC/DC adapter) is
present and that the batteries inside the receiver and/or optional
battery pack are fresh and installed with correct polarity.
Make sure all the connections between the wire harnesses and
system components are proper and positive.
Verify that the static inlet pressure meets the manufacturer’s recommended inlet pressure. If necessary adjust the line pressure
regulator.
If the recommended actions for the following troubleshooting chart
do not help to address the problem consider replacing wiring harnesses.
WARNING:
Any actions performed on the gas valve must be performed
in accordance with this instruction manual. Likewise, any
actions performed on the DFC or other system components
must be done in accordance with the individual component
instructions.
Replacement of components must be performed in accordance with this instructions manual.
29209-0-0911
Page 25
INTERMITTENT CONTROL SYSTEM TROUBLESHOOTING
1
If the DFC giving signal lock out:
The board should be unlocked to
reinitiate a pilot flame ignition (for
the correct unlock sequence refer
to the DFC Use and Installation
Instructions).
NO
Is the DFC board in
lock out?
NO
1.
Verify the electrical connections’ integrity and
make sure they are in accordance with the relevant
system wiring diagram. If necessary replace the
wire harness.
2.
Replace the DFC board.
YES
1. Check the spark electrode positioning - adjust
as necessary.
Was observed spark
at the Pilot Hood
before the DFC
board locked out?
2.
Replace the pilot assembly.
NO
3. Verify the electrical connections’ integrity and
make sure they are in accordance with the
relevant system wiring diagram. If necessary
replace the wire harness.
4.
Replace the DFC board.
YES
YES
1. Verify the electrical connections’ integrity and
make sure they are in accordance with the
relevant system wiring diagram. If necessary
replace the wire harness.
2. If pilot flow adjuster screw is not sealed:
Check if pilot flow adjust screw is set correctly in
accordance with the appliance manufacturer
instructions. If necessary correct it.
3. Replace pilot tube or complete pilot
assembly.
4. Replace the pilot orifice with a new orifice of
correct size, and type, or replace the pilot
assembly. Under all circumstances follow the
appliance manufacturer’s service instructions.
5. Remove the provided wiring harnesses from
Ev1 of gas valve (red base), and verify voltage at
ignition between the Ev1 terminal and the ground
connection on teh valve body. If the voltage is
greater than 0 then Replace Valve. Otherwise
Replace DFC.
Spark continues
while the pilot is ON.
1.
Replace the pilot assembly.
2.
Replace the DFC board.
YES
NO
2
Page 26
29209-0-0911
INTERMITTENT CONTROL SYSTEM TROUBLESHOOTING
2
Main burner lights
when the pilot only
should light.
1.
Replace DFC board.
2.
Replace the gas valve.
YES
1.
Verify the pilot flame fully engulfs the tip of the sense electrode. If not replace the pilot
assembly.
NO
2.
Replace the pilot assembly.
3.
Carefully clean the electrical connections of the sense cable, and the DFC board sense
cable connection.
Pilot holds the flame?.
NO
4.
Replace the sense cable, or the cable-sense electrode assembly, or the pilot assembly.
5.
Verify the pilot is properly grounded.
6.
Replace the pilot orifice with a new orifice of correct size, and type, or replace the pilot
assembly.
7.
YES
If pilot flow adjuster screw is not sealed, correct it.
1.
Verify the electrical connections’ integrity and make sure they are in accordance with the
relevant system wiring diagram. If necessary replace the wire harness.
2.
Check if the optional remote transmitter is in “thermostat” or “on” mode and verifyt there is a
call for heat (f using a thermostat remote). Adjust the setting for heat.
3.
Verify that the pilot hood is properly fitted and a pilot flame is directed to properly ignite the
main appliance burner.
Main burner ignites?
NO
4.
Replace the main burner orifice with a new orifice of correct size and type, or replace the
pilot assembly. Under all circumstances follow the service instructions.
5.
Remove the provided wiring harnesses from EV2 of gas valve (red base), and verify voltage
at ignition between the EV1 terminal and the ground connection on the valve body.
5.1 If the voltage is greater than 0 then Replace Valve.
5.2 Or Replace DFC.
6.
Check the pressure at the outlet pressure test point out according to the manufacturer’s
instruction. If not in accordance, replace the gas valve.
YES
1.
Verify the electrical connections’ integrity and make sure they are in accordance with the
relevant system wiring diagram. If necessary replace the wire harness.
2.
Check the pressure at the outlet pressure test point out according the manufacturer’s
instruction. If not in accordance replace the gas valve.
Main burner remains
ON
NO
3.
With the system in the OFF position, connect the voltmeter between the EV2 terminal
(green base) on the valve, and the ground on the valve body.
Turn the system ON, let pilot light, and observe the following voltage sequence: once the pilot
flame is proved, the voltage on EV2 should spike to approx. 5 VdC for approx. 2 sec and then
drop to approx. 0.6 VdC continuously.
3.1 If the sequence is respected, replace the gas valve.
3.2 If the sequence is not respected, replace the DFC board.
1.
Replace the main burner orifice with a new orifice of correct size (partial blockage possible).
Verify that the main burner flame modulates. If it does not modulate replace the gas valve.
Main burner
modulates
properly?
2.
Verify that the gas valve outlet pressure limits are in accordance with the manufacturer
specifications. If not replace the gas valve.
FOR MANUAL HI/LO VERSION
3.
Verify the flame changes while rotating the HI/LO knob on the front of the gas valve. If there
is no change replace the gas valve.
29209-0-0911
Page 27
INSERT MAINTENANCE AND SERVICE
Although the frequency of servicing and maintenance will depend
on use and the type of installation, you should have a qualified
service technician perform an appliance checkup at the beginning
of each heating season. Specific guidelines regarding each
appliance maintenance task are listed below.
Cleaning
IMPORTANT: TURN OFF THE GAS BEFORE SERVICING YOUR
APPLIANCE.
Frequency: After the first 3 to 4 hours of use. As necessary after
initial cleaning.
Cleaning Burner and Controls
Frequency: Once annually.
By: Qualified service technician.
Task: Brush or vacuum the control compartment, fireplace logs
and burner areas surrounding the logs.
Checking Flame Patterns, Flame Height
Frequency: Periodically.
Use a soft brush attachment on a vacuum cleaner to gently remove
dust or soot deposits from liners and burner.
Cleaning Glass Door
By: Home owner.
Task: Remove and clean glass after the first 3 to 4 hours of use.
After the initial cleaning, clean as necessary. Film deposits on the
inside of the glass door should be cleaned off using a household
glass cleaner.
CAUTION
DO NOT handle or attempt to clean the door when it is hot
and DO NOT use abrasive cleaners.
By: Qualified service technician/Home owner.
Task: Make a visual check of your fireplace’s flame patterns.
Glass Door Replacement
Make sure the flames are steady - not lifting or floating. The
thermopile/thermocouple (standing pilot) tips should be covered
with flame. See Figure 21.
Do not operate the fireplace insert if the high-temperature ceramic
glass is cracked or broken.
Checking Vent System
Do not attempt to replace the ceramic glass panel. A complete
replacement glass door assembly should be ordered as listed in
the Parts List on pages 30-31, if needed.
Frequency: Before initial use and at least annually thereafter,
more frequently if possible.
Do not use substitute materials for replacement of glass door
components.
By: Qualified service technician/Home owner.
Do not abuse the glass door by striking the glass.
Task: Inspect the external vent cap on a regular basis to ensure
that no debris is interfering with the flow of air. Inspect entire vent
system for proper function.
Do not abuse the glass door by slamming or forcing the door
shut.
When installing the glass door assembly, place the top door flange
over the firebox top, center left to right, then gently swing the door
bottom inward. Secure the door with the two (2) spring loaded door
latches to the top door frame flange and the two (2) spring loaded
door latches to the bottom door frame flange.
NOTICE: Prior to operating this unit, be sure to clean the
interior porcelain coated liner panels and glass door with a
soft clean cloth. Due to normal manufacturing processes,
fingerprints along with excess sealing materials may be
present and should be removed. When cleaning, do not use
abrasives on the porcelain liners or the glass door assembly.
Page 28
29209-0-0911
ACCESSORIES
The following accessory parts can be obtained from your Empire Comfort Systems dealer. If you need additional information beyond
what your dealer can furnish, contact Empire Comfort Systems Inc., Nine Eighteen Freeburg Ave., Belleville, Illinois 62220.
40” (DVL25IN)
43” (DVL33IN)
6”
6”
22 1/4” (DVL25IN)
25 1/4” (DVL33IN)
28” (DVL25IN)
31” (DVL33IN)
14” (DVL25IN)
17” (DVL33IN)
2 1/4”
STD Contemporary Surround
•
•
Black
Black & Stainless
1 5/16”
Bottom Cover
•
•
Black
Used to raise insert and surround panels when
installed in a fireplace without a flush hearth
extension. Can be used with contemporary
surround kits.
OPTIONAL DECORATIVE GLASS ACCESSORIES
Accessory Model Number
Description
Loft Burner Model Used On
DG18BUC
Decorative Glass - Blue Clear
DVL(25,33)IN
DG18BKP
Decorative Glass - Black Polished
DVL(25,33)IN
DG18CLF
Decorative Glass - Clear Frosted
DVL(25,33)IN
29209-0-0911
Page 29
INSERT PARTS VIEW
1
1
2
3
37
36
39
4
4
35
34
5
40
8
7
33
32
9
10
7
12
11
13
20
16
19 18 17
15
14
22
42
21
22
45
25
41
23
28
24
43
6
27
4
4
26
38
47
29
31
44
46
30
INSERT PARTS LIST
PART NUMBER
INDEX
NO.
DVL25IN33(N,P)
DVL33IN33(N,P)
DVL25IN73(N,P)
DVL33IN73(N,P)
1
22950
22950
22950
22950
FLUE CONNECTOR GUIDE
2
23309
23211
23309
23211
SLIDE PLATE ASSEMBLY
3
R9188
R9188
R9188
R9188
GASKET, TOP
4
16223
27718
16223
27718
SPRING RETAINER ASSEMBLY
5
27666
27691
27666
27691
LOG SHELF
6
R10882
R10882
R10882
R10882
7
27667
27679
27667
27679
LINER SIDE - PORCELAIN
8
27669
27681
27669
27681
LINER REAR - PORCELAIN
9
27712
27713
27712
27713
GLASS DOOR FRAME ASSEMBLY
10
27726
27727
27726
27727
BURNER COVER, PORCELAIN
Page 30
DESCRIPTION
ELBOW 90° BRASS - 3/8 NPT X 3/8 FLARE
29209-0-0911
INSERT PARTS LIST
PART NUMBER
INDEX
NO.
DVL25IN33(N,P)
DVL33IN33(N,P)
DVL25IN73(N,P)
DVL33IN73(N,P)
11
27731
27856
27731
27856
RESTRICTOR, BURNER - LEFT
12
27855
27857
27855
27857
RESTRICTOR, BURNER - RIGHT
13a
R10737
R10737
R10423
R10423
PILOT ASSEMBLY, PSE NAT
13b
R10738
R10738
R10424
R10424
PILOT ASSEMBLY, PSE LP
14
M173
M173
M173
M173
GASKET, PILOT
15
R10732
R10733
R10732
R10733
TUBE BURNER
16
R7624
R7624
R7624
R7624
AIR SHUTTER
17a
P310
-
P310
-
ORIFICE #2.20mm (NAT)
17b
P289
-
P289
-
ORIFICE 1.35mm (LP)
17c
-
P285
-
P285
ORIFICE #39 (NAT)
ORIFICE 1.55mm (LP)
DESCRIPTION
17d
-
P258
-
P258
18
R7572
R7572
R7572
R7572
JAMB NUT
19
27086
27086
27086
27086
BURNER END SUPPORT
20
P212
P212
P212
P212
FITTING, ORIFICE
21
11269
11269
11269
11269
GAS LINE BRACKET
22
27662
27662
27662
27662
BURNER SUPPORT
23
27659
27686
27659
27686
BURNER BASE
24
28064
28064
-
-
VALVE, SHIELD
25
28063
28063
28683
28683
VALVE BRACKET
26a
R7577
R7577
R11125
R11125
VALVE, SIT - NAT
26b
R7578
R7578
R11126
R11126
VALVE, SIT - LP
27
R6207
R6207
R6207
R6207
ELBOW, 5/16 X 3/8 NPT 90°
28
27147
27672
28791
28793
TUBING ASSEMBLY - INLET
29
22953
22953
-
-
PIEZO BRACKET
30
R9760
R9760
-
-
PIEZO IGNITOR
31
R3436
R3436
-
-
SWITCH, REMOTE OFF/ON
32
R10961
R10961
R10961
R10961
FLEXLINE W/SHUT OFF VALVE
33
R2204
R2204
R2204
R2204
CORD SET
34
R7649
R7649
R7649
R7649
FAN CONTROL
35
R9268
R9268
R9268
R9268
WIRE ASSEMBLY-SWITCH
36
18879
18879
18879
18879
RHEOSTAT ASSEMBLY
37
24925
24925
24925
24925
BLOWER SUB-ASSEMBLY
(INCLUDES MOUNTING PLATE, PAD)
38
R3435
R3435
-
-
39
27660
27687
27660
27687
FIREBOX BAFFLE
40
27860
27860
27860
27860
PLATE, FIREBOX BAFFLE
41
-
-
29054
29054
RECEIVER PLATE
42
-
-
R2566
R2566
WIRE 9” BLACK (QTY. 2)
43
-
-
R2522
R2522
ON/OFF SWITCH
44
-
-
R11122
R11122
BATTERY HOLDER
45
-
-
R11127
R11127
DFC CONTROL BOARD
46
-
-
R11123
R11123
WIRE HARNESS
47
-
-
R11128
R11128
AC ADAPTOR, 7.0 VDC
WIRE ASSEMBLY SWITCH
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.
29209-0-0911
Page 31
MASTER PARTS DISTRIBUTOR LIST
To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort.
com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the
nature of the problem with the unit.
To Order Parts After the Warranty Period, please contact your dealer or one of the Master Parts Distributors listed below.
This list changes from time to time. For the current list, please click on the Master Parts button at www.empirecomfort.
com.
Please note: Master Parts Distributors are independent businesses that stock the most commonly ordered Original Equipment
repair parts for Heaters, Grills, and Fireplaces manufactured by Empire Comfort Systems Inc.
Dey Distributing
1401 Willow Lake Boulevard
Vadnais Heights, MN 55101
Phone: 651-490-9191
Toll Free: 800-397-1339
Website: www.deydistributing.com
Parts: Heater & Hearth
East Coast Energy Products
10 East Route 36
West Long Branch, NJ 07764
Victor Division of F. W. Webb Company
200 Locust Street
Hartford, CT 06114
Phone: 732-870-8809
Toll Free: 800-755-8809
Fax: 732-870-8811
Website: www.eastcoastenergy.com
Parts: Heater & Hearth and Grills
Phone: 860-722-2433
Toll Free: 800-243-9360
Fax: 860-293-0479
Toll Free Fax: 800-274-2004
Websites: www.fwwebb.com & www.victormfg.com
Parts: Heater & Hearth and Grills
HOW TO ORDER REPAIR PARTS
Parts Not Under Warranty
Parts can be ordered through your Service Person, Dealer, or a Master Parts Distributor. See this page for the Master Parts Distributors list. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the
service person/dealer.
Warranty Parts
Warranty parts will need a proof of purchase and can be ordered by your Service Person or Dealer. Proof of purchase is required for
warranty parts.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number and Serial Number from the
name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following illustration and part list. Be sure to give all this information . . .
Appliance Model Number
Appliance Serial Number
Part Description
Part Number
Type of Gas (Propane or Natural)
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
Page 32
29209-0-0911
APPLIANCE SERVICE HISTORY
Date
Dealer Name
29209-0-0911
Service Technician Name
Service Performed/Notes
Page 33
APPLIANCE SERVICE HISTORY
Date
Page 34
Dealer Name
Service Technician Name
Service Performed/Notes
29209-0-0911
APPLIANCE SERVICE HISTORY
Date
Dealer Name
29209-0-0911
Service Technician Name
Service Performed/Notes
Page 35
EMPIRE
Comfort Systems
Empire Comfort Systems Inc.
918 Freeburg Ave. Belleville, IL 62220
If you have a general question about our products, please e-mail us at
[email protected]
If you have a service or repair question, please contact your dealer.
www.empirecomfort.com
Page 36
29209-0-0911
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement