iFace Series User Manual
Facial & Fingerprint Recognition Product
Series User Manual
Version: 2.0
Date: June 2011
About This Manual
This document introduces the user interface and menu operations of the Facial &
Fingerprint Recognition (FFR) terminal series. For the installation of the FFR
terminal, see Facial & Fingerprint Recognition Product Series Installation Manual
iFace Series User Manual
ZKTechnologyEU
Content
1 Instruction for Use .............................................................................1
1.1 The Distance,Facial Expression and Stand Pose ....................1
1.2 Enrollment Pose.........................................................................2
1.3 Finger Placement .......................................................................3
1.4 Use of Touch Screen..................................................................4
1.5 Touch Operations.......................................................................5
1.6 Appearance of the FFR Terminal ...............................................6
1.7 Main Interface............................................................................7
1.8 Verification Modes.....................................................................9
1.8.1 Fingerprint Verification................................................9
1.8.2 Facial Verification ...................................................... 11
1.8.3 Password Verification ...............................................13
1.8.4 ID Card Verification *................................................14
2. Main Menu .......................................................................................16
3. User Management..........................................................................19
3.1. Adding a User .........................................................................20
3.1.1 Entering a User ID ....................................................21
3.1.2 Entering a Name .......................................................23
3.1.3 Enrolling a Fingerprint ..............................................25
3.1.4 Enrolling a Password................................................26
3.1.5 Enrolling a Face ........................................................28
3.1.6 Entering a Group No.................................................30
3.1.7 Enrolling an ID Card * ..............................................32
3.1.8 Enrolling an HID Card * ...........................................33
3.1.9 Enrolling an Mifare Card * .......................................33
3.1.10 Modify User Rights .................................................34
3.1.11 Enroll Photos............................................................35
3.2 Edit a User ...............................................................................36
I
iFace Series User Manual
ZKTechnologyEU
3.3 Delete a User............................................................................37
3.4 Query a User............................................................................38
3.4.1 Query by User ID ......................................................38
3.4.2 Query by Name .........................................................39
4. Communication-related Settings ..................................................40
4.1 Network Settings .....................................................................40
4.2 Serial Port Settings ..................................................................41
4.3 WIFI option * ..........................................................................42
4.4 Modem option * ......................................................................43
4.4.1 GPRS option ..............................................................43
4.4.2 GPRS option ..............................................................45
4.5 Wiegand Input * ......................................................................46
4.6 Wiegand Output.......................................................................46
4.6.1 Wiegand 26-bits Output Description ......................47
4.6.2 Wiegand 34-bits Output Description ......................49
4.6.3 Customized Format...................................................50
5. System Configuration.....................................................................55
5.1 Basic Parameters......................................................................55
5.2 Interface Parameters ................................................................56
5.3 Fingerprint Parameters.............................................................57
5.4 Face Parameters .......................................................................58
5.5 Log Settings .............................................................................60
5.6 Update......................................................................................61
6. Data Management ..........................................................................62
6.1 Query a Record ........................................................................63
6.2 Work Code ...............................................................................64
6.3 SMS * ......................................................................................66
6.3.1 Set Message ..............................................................66
6.3.2 Employee Check Message......................................68
II
iFace Series User Manual
ZKTechnologyEU
7. USB Disk Management .................................................................69
8. Keyboard Definitions ......................................................................71
9 Auto Test ...........................................................................................73
10 Screen Calibration.........................................................................75
11 Bell Setting .....................................................................................76
12 Access Control Setting * ..............................................................78
13 Date/Time Setting..........................................................................80
13.1 Set Date/Time ........................................................................80
13.2 Set Daylight Saving Time (DST)...........................................81
14 System Information .......................................................................83
14.1 Records ..................................................................................83
14.2 Terminal.................................................................................84
Appendix ..............................................................................................85
Appendix 1 Text Input Instructions ...............................................85
Appendix 2 Rules for Uploading Promotional Pictures ................87
Appendix 3 Introduction to Wiegand ............................................88
Appendix 4 Photo ID Function......................................................89
Appendix 5 Attendance Status Selection Function *.....................91
Appendix 6 Anti-pass back *.........................................................92
Appendix 7 Multi- verification methods * ....................................95
Appendix 8 GPRS * ....................................................................100
Appendix 9 Webserver * .............................................................100
Appendix 10 Soap * ...................... ¡Error! Marcador no definido.
Appendix 11 Statement on Human Rights and Privacy...............104
Appendix 12Environment-Friendly Use Description ..................106
III
iFace Series User Manual
ZKTechnologyEU
1 Instruction for Use
1.1 The Distance,Facial Expression and Stand Pose
1)The recommended distance:
The recommended distance between person and
device is 0.5m (applied to height range
1.5~1.85m). According to the obtained face image
from device to adjust, when the face image is
comparatively bright, please move backwards
appropriately; when the face image is
comparatively dark, please move forwards
appropriately.
2)The recommended facial expression and several poor-effect facial
expressions:
3 )The recommded stand pose and several poor-effect stand poses:
Note: During the enrollment and verification, please remain the normal
facial expression and stand pose.
1
iFace Series User Manual
ZKTechnologyEU
1.2 Enrollment Pose
During the enrollment, display the face in the centre of screen as possible. According
to the device’s voice prompts, do some small-scope head actions such as turn left,
turn right, rise, bow and so on to ensure that the different parts of face are inputted
into system to improve the verification accuration. The enrollment poses are as
follows:
Look ahead
(rise)
Focus on
the screen
Focus on
the camera
(bow)
2
Turn left
slightly
Turn right
slightly
iFace Series User Manual
ZKTechnologyEU
1.3 Finger Placement
Recommended fingers: The index finger, middle finger or the ring finger; the thumb
and little finger are not recommended (because they are usually clumsy on the
fingerprint collection screen).
1)
Proper finger placement:
The finger is flat to the surface
and centered in fingered guide.
2)
Improper finger placement:
Not flat to the surface
Off-center
Slanting
Off-center
Please enroll and verify your fingerprint by using the proper finger placement
mode. We shall not be held accountable for any consequences arising out of
the degradation in verification performance due to improper user operations.
We shall reserve the right of final interpretation and revision of this document.
3
iFace Series User Manual
ZKTechnologyEU
1.4 Use of Touch Screen
Touch the screen with one of your fingertips or the top of the forward edge of a
fingernail, as shown in the following figure. A broad point of contact may lead to
inaccurate pointing.
When the touch screen is less sensitive to the touch, you can perform screen
calibration through menu operations. Press [Menu] → [Calibration] on the screen
and a cross icon will be displayed. After you touch the center of the cross at five
locations on the screen correctly, the system automatically returns to the main menu.
Press [Return] to return to the initial interface. For details, see 10 Screen Calibration
in this manual.
Smear or dust on the touch screen may affect the performance of the touch screen.
Therefore, try to keep the screen clean and dust-free.
4
iFace Series User Manual
ZKTechnologyEU
1.5 Touch Operations
1)
Enter numbers. Press the [User ID] key. The system automatically displays the
number input interface. After entering the user ID, press [OK] to save and
return to the previous interface.
2)
Enter Text. Press the [Name] key. The system automatically displays the text
input interface. After entering the user name, press [X] to save and return to the
previous interface.
3)
Modify parameters. Press the default value of a parameter and the system
automatically switches to another value of this parameter.
5
iFace Series User Manual
ZKTechnologyEU
1.6 Appearance of the FFR Terminal
Indicator
Touch screen
Push buttons
Fingerprint
collection area
ID card
area
Camera
6
swipe
iFace Series User Manual
ZKTechnologyEU
1.7 Main Interface
① Menu
② Time
③ Date
④ 1:1 or 1:G Function Key
⑤ Facial/Fingerprint Switch Key
⑥ Current Group No.
⑦ Facial/Fingerprint Image
⑧ Attendance Status
⑨
F1
F2
F3
F4
F5
F6
Screen
Shortcut
Keys
⑩ Keyboard Shortcut Keys
①Menu: You can enter the main menu by touching this key.
②Time: Current time is displayed. Both the 12-hour and 24-hour time systems are
supported.
③Date: Current date is displayed.
④1:1 or 1:G Function Key: You can enter the digital input interface of 1:1 or 1:G
verification mode. You can set the “1:1/1:G” shortcut key through ⑨ Screen Shortcut
Keys. This key is automatically hidden if the [Toolbar Style] is set to “Permanent
Display”.
⑤Facial/Fingerprint Switch Key: By pressing this key, you can switch between the
facial and fingerprint recognition modes. You can set the “Facial/Fingerprint Switch
Key” shortcut key through ⑨ Screen Shortcut Keys. This key is automatically hidden
if the [Toolbar Style] is set to “Permanent Display”.
7
iFace Series User Manual
ZKTechnologyEU
⑥Current Group No.: When the terminal is currently in the facial recognition mode,
users in current group can perform facial comparison directly, while users of another
group need to enter the group No. before performing the facial comparison.
⑦Facial/Fingerprint Image: If a facial image is displayed, the terminal is currently in
the facial recognition mode; if a fingerprint image is displayed, the terminal is
currently in the fingerprint recognition mode. You can change current recognition
mode
of
the
terminal
through
⑤
Facial/Fingerprint
Switch
Key,
the
Facial/Fingerprint Key in ⑨ Screen Shortcut Keys or related key in ⑩ Keyboard
Shortcut Keys.
⑧Attendance Status: Current attendance status is displayed. This key is hidden
when ⑨ Screen Shortcut Keys are displayed.
⑨Screen Shortcut Keys: Press related shortcut keys to display the attendance
status or enter the functional interface quickly. Users can customize the function of
each shortcut key. For details, see 8 Keyboard.
⑩Keyboard Shortcut Keys: The Keyboard Shortcut Keys have a one-to-one
relationship with ⑨ Screen Shortcut Keys. Press related shortcut keys to display the
attendance status or enter the functional interface quickly.
8
iFace Series User Manual
ZKTechnologyEU
1.8 Verification Modes
1.8.1 Fingerprint Verification
(1)
1:N fingerprint verification
In the fingerprint verification mode, the terminal compares current fingerprint
collected by the fingerprint collector with all fingerprint data on the terminal.
1. To enter the fingerprint verification
mode (Figure 1 on the right), you can:
A) Press [Facial/Fingerprint Switch Key]
on the screen, or
B) Press [Facial/Fingerprint] shortcut
key on the screen, or
C) Press the keyboard shortcut key
[F6].
2. Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see 1.1 Finger
Placement.
3. If the verification is successful, an
interface as shown in Figure 2 on the
right will be displayed.
4. If the verification is not successful, an
interface as shown in Figure 3 on the
right will be displayed.
9
iFace Series User Manual
(2)
ZKTechnologyEU
1:1 fingerprint verification
In the 1:1 fingerprint verification mode, the
terminal compares current fingerprint
collected through the fingerprint collector
with that in relation to the user ID entered
through keyboard. Adopt this mode only
when it is difficult to recognize the fingerprint.
1. To enter the 1:1 recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2. Enter user ID and then press the
"Fingerprint” icon (Figure 2 on the right) to
enter 1:1 fingerprint recognition mode. If
the
prompt
“Unregistered
user!”
is
displayed, the user ID is nonexistent or
the user ID bearer has not enrolled his/her
fingerprint.
3. Press your finger on the fingerprint
collector by adopting the proper finger
placement. For details, see 1.1 Finger
Placement.
4. If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. 4. If the verification is not successful, an interface as shown in
Figure 4 on the right will be displayed.
10
iFace Series User Manual
ZKTechnologyEU
1.8.2 Facial Verification
(1)
1:G facial verification
Current group No. is displayed on the facial recognition interface. Users in
current group can perform facial comparison directly. Users of another group
can perform facial comparison only after
entering the group No. or selecting it using
the shortcut key. And the system will set
the group entered or selected by users to
be the current group instantly.
1. To enter the 1:G recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2. Enter user Group No. and then press
the "1:G” icon (Figure 2 on the right) to
enter 1:G fingerprint recognition mode.
3. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression. Current
Group No. is displayed on the comparison
interface, as shown in Figure 3 on the right.
Note: Check whether you are in current
group; if not, return to Step 1.
4. If the verification is successful, an
interface as shown in Figure 4 on the right
will be displayed.
11
iFace Series User Manual
(2)
ZKTechnologyEU
1:1 facial verification
In the 1:1 facial verification mode, the
terminal compares current facial collected
through the facial collector with that in
relation to the user ID entered through
keyboard. Adopt this mode only when it is difficult to recognize the facial.
1. To enter the 1:1 recognition mode, you can:
A) Press [1:1/1:G] on the screen, as shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For details, see 8 Keyboard.
2. Enter user ID and then press the "1:1
Facial” icon (Figure 2 on the right) to enter
1:1 facial recognition mode. If the prompt
“Unregistered user!” is displayed, the user
ID is nonexistent or the user ID bearer has
not enrolled his/her face in the system.
3. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression. Current
Group No. is displayed on the comparison
interface, as shown in Figure 3 on the right.
4. If the verification is successful, an
interface as shown in Figure 4 on the right
will be displayed. The system will return to
the main interface if the verification is not
passed within 20 seconds.
12
iFace Series User Manual
ZKTechnologyEU
1.8.3 Password Verification
In the password verification mode, the terminal compares the password entered with
that in relation to the user ID.
1.
To enter the password verification mode,
you can:
A) Press [1:1/1:G] on the screen, as
shown in Figure 1 on the right, or:
B) Press [1:1/1:G] shortcut key on the
screen, or
C) Press related shortcut key on the keyboard.
Note: You can enter the 1:1 recognition mode through B) and C) only after
setting a shortcut key for “1:1/1:G”. For
details, see 8 Keyboard.
2.
Enter the user ID and then press the "Key”
icon (Figure 2 on the right) to enter
password verification mode. If the prompt
“Unregistered user!” is displayed, the user
ID is nonexistent or the user ID bearer has
not enrolled his/her password in the
system.
3.
Enter the password and press the “OK”
icon to start the password comparison, as
shown in Figure 3 on the right.
4.
If
the
verification
is
successful,
an
interface as shown in Figure 4 on the right
will be displayed.
13
iFace Series User Manual
ZKTechnologyEU
1.8.4 ID Card Verification *
Only the products with a built-in ID card module support the ID card verification. The
products with a built-in ID card module support the following two verification modes:
ID Card Only: Users only need to swipe their ID cards for verification.
ID + Facial Verification: After passing the ID card verification, you also need to
perform facial verification.
For the settings of these two verification modes, see 5.5 Attendance Parameters.
1)
ID Card Only
1. If you have your ID card number enrolled in the system, you can pass the
verification by swiping your ID card at the swiping area in a proper way.
2. If the verification is successful, an
interface as shown in Figure 1 on the
right will be displayed.
3. If the verification is not successful, an
interface as shown in Figure 2 on the
right will be displayed.
14
iFace Series User Manual
2)
ZKTechnologyEU
ID + Facial Verification
1. Swipe your ID card properly at the
swiping area to enter the 1:1 facial
verification mode, as shown in Figure 1 on
the right:
2. Compare the facial in a proper way. For
details, see 1.1 Standing Position and
Posture, and Facial Expression.
3. If the verification is successful, an
interface as shown in Figure 3 on the right
will be displayed. The system will return to
the main interface if the verification is not
passed within 20 seconds.
15
iFace Series User Manual
ZKTechnologyEU
2. Main Menu
There are two types of rights respectively granted to two types of users: the ordinary
users and administrators. Ordinary users are only granted the rights of facial,
fingerprint, password or card verification, while administrators are granted the
access to the main menu for various operations apart from having all the privileges
granted to ordinary users.
Press [Menu] on the initial interface to access the main menu, as shown in the
following figure:
Any user can access the main menu by pressing the [Menu] key if the
system is free from administrators. After administrators are configured
on the terminal, the terminal needs to verify the administrators’ identity
before granting them access to the main menu. To ensure terminal
security, it is recommended to set an administrator when using the
terminal initially. For detailed operations, see 3.1.8.
16
iFace Series User Manual
ZKTechnologyEU
The main menu includes ten submenus and three shortcut keys, as shown in the
following figure:
Return to Initial Interface
Add a User
Set Date/Time
System Information
User Mgt.: Through this submenu, you can browse the user information stored on
the terminal, including the user ID, name, fingerprint, facial, card, password, rights
and group No.; add, modify or delete the user information.
Comm.: Through this submenu, you can set related parameters for communication
between the FFR terminal and PC, including the IP address, gateway, subnet mask,
baud rate, equipment No. and communication password.
System: Through this submenu, you can set system-related parameters, including
the basic parameters, interface parameters, fingerprint, facial and attendance
parameters, to enable the FFR terminal to meet user requirements to the greatest
extent in terms of functions and display.
Data Mgt.: Through this submenu, you can perform management of data stored on
the FFR terminal, for example, deleting the attendance record, all data and
promotional pictures, purging management rights and resetting the FFR terminal to
factory defaults.
Dn/Upload: Through this submenu, you can import user information and attendance
17
iFace Series User Manual
ZKTechnologyEU
data stored in a USB disk to related software or other fingerprint recognition
equipment.
Keyboard: Through this submenu, you can customize six shortcut keys. Related
status will be displayed by pressing related status key.
Auto Test: This submenu enables the system to automatically test whether functions
of various modules are normal, including the screen, collector, voice, facial,
keyboard and clock tests.
Calibration: When the touch screen is less sensitive to the touch, you can calibrate
the screen on the calibration interface through this submenu.
Bell: Through this submenu, you can set the alarm time and duration.
Access: Through this submenu, you can set the parameters of the electronic locks
and related access control devices.
18
iFace Series User Manual
ZKTechnologyEU
3. User Management
Browse the user information, including the user ID, name, fingerprint, face, ID card,
password, rights and the group that the user belongs to. Add, edit or delete the basic
information of users.
Press [User Management] on the main menu interface to display the user
management interface.
①Return to the Menu interface
②Query a user
③Add a user
④Scroll bar
⑤User list area
⑥Character selection area
The user is an administrator.
The user has enrolled his/her fingerprint.
The user has enrolled his/her facial image.
The user has enrolled his/her ID card.
The user has enrolled his/her password.
Note:
1)
In User List Area, users are listed in alphabetical order by last name. If you
select a user in User List Area, you can access the editing interface of this
user to edit or delete related user information.
2)
In Character Selection Bar, users are listed in alphabetical order by last name
by default and you can locate the desired user quickly. You can press [Query]
19
iFace Series User Manual
ZKTechnologyEU
to locate and query a user through the user ID. For details, see Section 3.4
Querying a User.
3.1. Adding a User
Press [Add] on the [User Mgt.] interface to display the [Add User] interface as shown
below.
User ID: Enter a user ID. 1- to 9-digit user IDs are supported by default.
Name: Enter a user name. 12-character user names are supported by default.
Fingerprint: Enroll a user’s fingerprint and the FFR terminal displays the number of
enrolled fingerprints. A user can enroll 10 fingerprints at maximum.
Face: Enroll a user’s face.
Password: Enroll a user’s password. 1- to 8-digit passwords are supported by default.
Role: Set the rights of a user. A user is set to ordinary user by default and can also
be set to administrator. Ordinary users are only granted the rights of facial,
fingerprint or password verification, while administrators are granted the access to
the main menu for various operations apart from having all the privileges granted to
ordinary users.
Group No.: Set the group that the user belongs to. Valid group No.: 1–24.
Photo: Enroll a user’s photo. During user verification, the user’s photo is displayed on screen.
Reg.Duress FP: Enroll a user’s fingerprint, and setting it as Duress FP.
The ID card is an optional function. If you need this function, please consult
our commercial representatives or fore-sale technical support personnel.
20
iFace Series User Manual
ZKTechnologyEU
3.1.1 Entering a User ID
The FFR terminal automatically allocates an ID starting from 1 for every user in
sequence. If you use the ID allocated by the FFR terminal, you may skip this section.
1.
Press [User ID] on the [Add User] interface to display the user ID management
interface, as shown below:
Tip: The user ID can be modified during initial enrollment, but once
enrolled, it cannot be modified.
2.
On the displayed keyboard interface, enter a user ID and press <OK> as
shown below. If a prompt message “The user ID already exists!” is displayed,
enter another ID.
Tip: The FFR terminal supports 1- to 9-digit user IDs by default. If you
need to extend the length of current user ID numbers, please consult our
commercial representatives or fore-sale technical support personnel.
21
iFace Series User Manual
3.
ZKTechnologyEU
After the user ID is entered, an interface is displayed as show below on the
right. Press [Save] to save current information and return to the previous
interface. Press [User Mgt.] to return to the previous interface without saving
current information.
22
iFace Series User Manual
ZKTechnologyEU
3.1.2 Entering a Name
Enter a user name through the keyboard.
1. Press [Name] on the [Add User] interface to display the name input interface, as
shown below.
2.
On the displayed keyboard interface, enter a user name and press [X] as
shown below. For details of operations on keyboard interface, see “Keyboard
Instructions”.
Tip: The FFR terminal supports the 1- to 12-character names by default.
23
iFace Series User Manual
3.
ZKTechnologyEU
After the user name is entered, the interface is displayed as shown below.
Press [Save] to save current information and return to the previous interface.
Press [User Mgt.] to return to the previous interface without saving current
information.
24
iFace Series User Manual
ZKTechnologyEU
3.1.3 Enrolling a Fingerprint
1. Press [Fingerprint] on the [Add User] interface to display the [Enroll Fingerprint]
interface, as shown below.
2.
On the displayed [Enroll Fingerprint]
interface (as shown in the Figure 1 on
the right), place your finger on the
fingerprint collector properly according
to the system prompt. For details, see
“Finger Placement”.
3.
Place the same finger on the fingerprint
collector for three consecutive times
correctly. If the enrollment succeeds,
the system will display a prompt
message “Enrolled Successfully” and
automatically return to the [Add User]
interface (as shown in Figure 2 on the right). If the enrollment fails, the system
will display a prompt message and return to the [Enroll Fingerprint] interface. In
this case, you need to repeat the operations of step 2.
25
iFace Series User Manual
4.
ZKTechnologyEU
You can back up the enrolled fingerprint of a user by pressing [Fingerprint]. A
user can enroll 10 fingerprints at maximum.
5.
Press [Save] to save current information and return to the previous interface.
Press [User Mgt.] to return to the previous interface without saving current
information.
3.1.4 Enrolling a Password
1.
Press [Password] on the [Add User] interface to display the password
management interface, as shown below.
26
iFace Series User Manual
2.
ZKTechnologyEU
On the displayed keyboard interface, enter a password and press <OK> as
shown below. Re-enter the password according to the system prompt and then
press <OK>.
Tip: The FFR terminal supports the 1- to 8-digit passwords by default.
3.
After the password is entered, an interface is displayed as shown below. Press
[Save] to save current information and return to the previous interface. Press
[User Mgt.] to return to the previous interface without saving current information.
27
iFace Series User Manual
ZKTechnologyEU
3.1.5 Enrolling a Face
1.
Press [Face] on the [Add User] interface to display the face enrollment interface,
as shown below.
2.
On the displayed face enrollment interface (as shown below), turn your head to
the left and right slightly, raise and lower your head according to the voice
prompts, so as to enroll different parts of your face into the system to assure
accurate verification. See 1.1 The distance, Facial Expression and Stand Pose.
28
iFace Series User Manual
3.
ZKTechnologyEU
If your facial image is enrolled successfully, the system will display a prompt
message and automatically return to the [Add User] interface (as shown below).
4.
Press [Save] to save current information and return to the previous interface.
Press [User Mgt.] to return to the previous interface without saving current
information.
29
iFace Series User Manual
ZKTechnologyEU
3.1.6 Entering a Group No.
The FFR terminal enables the facial comparison function by default. During face
enrollment, the FFR automatically allocates a group No. starting from 1 for every
user in sequence. When the number of users in Group No.1 reaches the upper limit,
the rest users fall under Group No.2 automatically. Up to 100 facial images can be
enrolled in Group No.1 and only 50 facial images can be enrolled in other groups. If
you use the group No. allocated by the FFR terminal, you may skip this section.
1.
Press [Group No.] on the [Add User] interface to display the group No.
management interface, as shown below.
2.
On the displayed keyboard interface, enter your group No. and press <OK> as
shown below.
Tip: A valid group No. contains 1–24 digits.
30
iFace Series User Manual
3.
ZKTechnologyEU
After the group No. is entered, an interface is displayed as shown below. Press
[Save] to save current information and return to the previous interface. Press
[User Mgt.] to return to the previous interface without saving current information.
Tip: Please remember your own group No.
31
iFace Series User Manual
ZKTechnologyEU
3.1.7 Enrolling an ID Card *
1.
Press [Card] on the [Add User] interface
to display the [Enroll Card] interface, as
shown in Figure 1 on the right.
2. The [Punch Card!] interface pops out as
shown in Figure 2 on the right. Swipe
your ID card properly in the swiping area.
For details, see “1.6 Appearance of the
FFR Terminal”.
3.
If the card passes the verification, the
FFR
terminal
displays
a
prompt
message “Read Successfully! Card No.:
**********”, as shown in Figure 3 on the
right, and returns to the [Add User]
interface. Press [Card] to display the enrolled card number as shown in Figure 4
on the right.
4.
Press [Save] to save current information
and return to the previous interface.
Press [User Mgt.] to return to the
previous interface without saving current
information.
32
iFace Series User Manual
ZKTechnologyEU
3.1.8 Enrolling an HID Card *
This operation procedure is same as ID Card
operation, use HID card only by Using
125MHZ,13.56 MHz contactless smart card
technology only, these fingerprint products
provide users with new options for supporting
multi-authentication of identity. Combine a
contactless
card
presentation
with
a
fingerprint biometric. Or, use a personal identification number (PIN) number along
with a contactless card presentation. (See multi-authentication)
HID standard card is encrypted by using specify format encode card ID and the
equipment code.
Note:HID card apply to fingerprint -machine, this is an option function on the
fingerprint machine, if you want to customize fingerprint machine with HID
card function, please contacts our market supporter and salesman.
3.1.9 Enrolling an Mifare Card *
The iface series only favors Mifare card's
being an ID card use. Use step and ID card
to register an operation to accord.
Note:Mifare card is an option function on
the fingerprint machine, if you want to
customize the fingerprint machine with
Mifare card function, please contacts our
market supporter and salesman’s.
33
iFace Series User Manual
ZKTechnologyEU
3.1.10 Modify User Rights
1.
On the [Add User] interface, press [Role:
User]
to
change
the
user
into
an
administrator, as shown in Figure 1 on the
right.
Note: There are two types of rights
respectively granted to two types of
users: the ordinary users and administrators. Ordinary users are only
granted the rights of facial, fingerprint, or password verification, while
administrators are granted the access to the main menu for various
operations apart from having all the privileges granted to ordinary users.
2.
After
the
modification
is
done,
the
interface is as shown in Figure 2 on the
right.
Press
information
[Save]
and
to
return
save
to
current
previous
interface; press [User Mgt.] to directly
return to previous interface without saving
current information.
34
iFace Series User Manual
ZKTechnologyEU
3.1.11 Enroll Photos
If you have enrolled your photo in the system, the system will display your enrolled
photo in addition to your ID and name after you pass the verification.
1.
Press [Photo]
on the
[Add
User]
interface to display the photo enrollment
interface, as shown in Figure 1 on the
right.
2.
On the photo enrollment interface,
stand naturally in front of the screen.
For details, see 1.1 Standing Position
and Posture, and Facial Expression.
Press [Capture] to display the photo
taken at the lower left corner, as shown
in Figure 3 on the right.
3.
After taking the photo, press [Exit] to
return to previous interface.
4. After the photo is taken, the interface is as
shown in Figure 4 on the right. Press [Save]
to save current information and return to
previous interface; press [User Mgt.] to
directly return to previous interface without
saving current information.
35
iFace Series User Manual
ZKTechnologyEU
3.2 Edit a User
Select a user from the User List to enter [User Info] interface.
The User ID cannot be modified, and the other operations are similar to those
performed to add a user. You can re-enroll your fingerprint and facial image, change
your password and modify the management rights and group No.
36
iFace Series User Manual
ZKTechnologyEU
3.3 Delete a User
On the [User Info] interface, you can delete all or partial user information.
1.
Press [Delete] to delete a user, as shown below.
2.
On the interface displayed (as shown below), click [YES] to delete current user
and [NO] to return to previous interface.
3.
On the [User Info] interface, press [Name], [Fingerprint], [Face] or [Password] to
delete related user information.
37
iFace Series User Manual
ZKTechnologyEU
3.4 Query a User
To facilitate administrators to locate a user quickly from a large number of enrolled
users, the FFR terminal enables user query by his/her “User ID” and “Name”.
(Location Search)
3.4.1 Query by User ID
1. Press [Query] on the [User Management]
interface to display the User ID query
interface, as shown in Figure 1 on the
right.
2.
Enter the user ID on the displayed
interface, and click [OK] (as shown in
Figure 2 on the right) to locate the cursor
to the desired user (as shown in Figure 3
on the right).
38
iFace Series User Manual
ZKTechnologyEU
3.4.2 Query by Name
On the [User Management] interface, enter the user name through the “Character
Selection Bar” to locate the cursor to the desired user, as shown in the following
figure:
By selecting a character from the “Character Selection Bar”, you can quickly locate
the users whose names start with this character. Users are listed in alphabetical
order by last name by default.
39
iFace Series User Manual
ZKTechnologyEU
4. Communication-related Settings
You can set related parameters for the communication between the FFR terminal
and PC, including the IP address, gateway, subnet mask, baud rate, equipment No.
and communication password.
4.1 Network Settings
When the FFR terminal communicates with the PC over Ethernet, you need to check
the following settings:
IP Address: The IP address is 192.168.1.201 by default and can be changed as
required; the IP address of the FFR terminal and that of the PC cannot be duplicated.
Subnet Mask: The subnet mask is 255.255.255.0 by default and can be changed as
required.
Gateway: The gateway is 0.0.0.0 by default. If the FFR terminal and the PC are not
located in the same network segment, you need to set the gateway.
40
iFace Series User Manual
ZKTechnologyEU
4.2 Serial Port Settings
When the FFR terminal communicates with the PC over serial ports (RS232/RS485), you need
to check the following settings:
RS232: This parameter is used to enable or disable the RS232 communication. If the RS232
communication cables are used, set this parameter to “ON”.
RS485: This parameter is used to enable or disable the RS485 communication. If the RS485
communication cables are used, set this parameter to “ON”.
Baud Rate: This parameter is used to set the baud rate for the communication between the
FFR terminal and the PC. It includes five options: 9600, 19200, 38400, 57600, and 115200.
The high baud rate is recommended for the RS232 communication to achieve high
communication speed, while the low baud rate is recommended for the RS485 communication
to achieve stable low-speed communication.
Device ID: This parameter is used to set the ID of device from 1 to 254. If the RS232/RS485
communication is adopted, you need to enter the device ID on the software communication
interface.
Comm Key: To enhance the security of attendance data, you can set a password for the
connection between the FFR terminal and PC. Once the password is set, you can connect the
PC with the FFR terminal to access the attendance data only after entering the correct
password. The default password is 0 (that is, no password). Once a password is set, you need
to enter this password before connecting the PC software with the FFR terminal; otherwise, the
connection is unsuccessful. 1- to 6-digit passwords are supported.
Considering the massive data including the fingerprint and facial templates
stored in the FFR terminal, it is recommended to transfer the data between the
FFR terminal and PC over network to enhance the transfer speed.
41
iFace Series User Manual
ZKTechnologyEU
4.3 WIFI option *
Before the device is used for wireless network, other physical groupware of 802.11
network, such as joint, distributing system, wireless medium must be in existence.
ESSID to connect to the network must be known (network ID).
Network ID: Network ID to be connected to wireless network. (There is difference
between small letter and capital letter.)
Network model: there are two models: infrastructure model (for star structure) and
ad-hoc model (for peer-to-peer-network).
Authentication mode: Infrastructure mode includes five authentication modes: OPEN,
SHARED, WEPAUTO, WPAPSK and WPA2PS002E.
ad-hoc model includes four authentication modes: OPEN, SHARED, WEPAUTO
and WPANONE.
Encrypt type:when the selected encrypt type is NONE,the password in WEP (Wired
equivalent privacy) and WPA (WiFi protested access) cannot be edited, namely, it is
not necessary to input password.
Device IP address :In 802.11 wireless network, there is DHCP. Or enter IP interface
to input correct IP address, subnet mask and so on.
Operation
Press ▲/▼ to switch cursor to the input box or button. Use T9 input to input network
ID, which must be input, or the cursor cannot be moved to other input box. Then
press
/
to select the item to be set or press OK to do corresponding operation.
42
iFace Series User Manual
ZKTechnologyEU
1)set password :
According to the selected authentication mode and different encrypt types, the
interface where password is set is also different. There are two interfaces: WEP and
WPA.
WEP password
2)specify IP:
Specify the device IP in wireless network. It has nothing to do with network option in
communication option.
After IP is specified, press
wireless option interface.
After setting, press
button to save the setting, and then return to
button to return to the last interface.
4.4 Modem option *
4.4.1 GPRS option
When the equipment is in the Dial-Up Network, make sure the device is in the
coverage of GPRS or CDMA signal, and it is must known of the used modem type,
43
iFace Series User Manual
ZKTechnologyEU
APN name and access number and so on.
Frequency: Select the appropriate frequency according to the business operators.
APN Name: Access Point Name, used to identify GPRS / CDMA types of business.
User name and password: Verify whether the user has permission to use this
network.
Access Number: The access number of GPRS / CDMA business.
Redial interval:The interval of automatic redial after the network is disconnected.
Redial times: The times of attempt to redial the number if the network is
disconnected.
Whether Use: According to needs to choose is or otherwise, the choice is when
single-clicks the
button to be possible to enter the GPRS establishment
page, the following chart shows:
Single-clicks the “GPRS Information” item can see the detail, show below:
Notice:Dial-Up setting function is only available on some models.
Operation :
44
iFace Series User Manual
ZKTechnologyEU
Press on the desired item,then start the T9 method to input APN name, user name,
Link Psw and Access Num. directly enter the value in the input box. When finished
all this settings, you just press the
previous screen.
button to save them and return to the
4.4.2 GPRS Use
1) Dial-Up
After dialup settings are completed, reboot the device, the device will automatically
begin dialing, when dial-up is successful, the screen will be displayed the GPRS icon
below:
2) Data download
When Dial-up is successful, open the data download program in the server, when
the user is verified through the terminal, the device will automatically transmit data to
the server, the interface will prompt "in Communication ... ..." when download;
45
iFace Series User Manual
ZKTechnologyEU
4.5 Wiegand Input *
Wiegand Input Format: User defined Wiegand input format. Include three Input
Format: Standard Wiegand 34-bits, Standard Wiegand 34-bits, User Define Format .
Pulse width: Pulse width is 100 microseconds by default, which can be adjusted
from 20 to 800.
Pulse interval:It is 900 microseconds by default, which can adjusted between 200
and 20000.
Input content:Content contained in Wiegand input signal, including User ID or card
number.
Operation
4.6 Wiegand Output
Wiegand Format: The system has two built-in formats Wiegand 26-bits and
Wiegand 34-bits, and also supports the format customization function to meet
individualized requirements.
Failed ID: refers to the value output by the system upon verification failure. The
46
iFace Series User Manual
ZKTechnologyEU
output format is subject to the setting of “Wiegand Format”. The default value scope
of Failed ID is 0–65535.
Site Code: The site code is used for customized Wiegand format. The site code is
similar to the device ID, but the site code is customizable and can be duplicated
among different devices. The default value scope of the site code is 0–255.
Pulse Width: refers to the width of the Wiegand pulse in microseconds. The default
value scope of the pulse width is 1–1000.
Pulse Interval: refers to the interval of the Wiegand pulse in microseconds. The
default value scope of the pulse width is 1–10000.
Output: refers to the contents output upon successful verification. You can select the
“User ID” or “Card Number” as the output.
4.6.1 Wiegand 26-bits Output Description
The system has a built-in Wiegand 26-bits format. Press [Wiegand Format], and
select “Standard Wiegand 26-bits”.
The composition of the Wiegand 26-bits format contains 2 parity bits and 24 bits for
output contents (“User ID” or “Card Number”). The binary code of 24-bits represent
up to 16,777,216 (0–16,777,215) different values.
1
Even parity
2
25 26
User ID/Card Number
Odd parity bit
bit
Definition of Fields:
Field
Meaning
Even parity bit
Judged from bit 2 to bit 13. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
47
iFace Series User Manual
ZKTechnologyEU
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–16777215)
Number (bit 2-bit 25)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 14 to bit 25. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the odd
parity bit is 0.
For example, for a user with user ID of 12345, the enrolled card number is
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
00000000000110000001110011
Even parity bit
User ID = Binary code of 12345
Odd parity bit
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
11100110000100011110100000
Even parity bit User ID = Binary code of 0013378512 Odd parity bit
3) The Wiegand output is as follows upon verification failure:
00000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
Note: If the output contents exceed the scope allowed for the Wiegand format,
the last several bits will be adopted and first several bits are automatically
discarded. For example, the user ID 888 888 888 is 110 100 111 110 110 101 111
48
iFace Series User Manual
ZKTechnologyEU
000 111 000 in binary format. Wiegand26 only supports 24 bits, that is, it only
outputs the last 24 bits, and first 6 bits “110 100” are automatically discarded.
4.6.2 Wiegand 34-bits Output Description
The system has a built-in Wiegand 34-bits format. Press [Wiegand Format], and
select “Standard Wiegand 34-bits”.
The composition of the Wiegand 34-bits format contains 2 parity bits and 32 bits for
output contents (“User ID” or “Card Number”). The binary code of 32-bits represent
up to 4,294,967,296 (0–4,294,967,295) different values.
1
2
33 34
Even
User ID/Card Number
Odd parity bit
parity bit
Table 2 Definition of Fields
Field
Meaning
Even parity bit
Judged from bit 2 to bit 17. The even parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
even parity bit is 1.
User
ID/Card
User ID/Card Number (Card Code, 0–4,294,967,295)
Number (bit 2-bit 33)
Bit 2 is the Most Significant Bit (MSB).
Odd parity bit
Judged from bit 18 to bit 33. The odd parity bit is 1 if the
character has an even number of 1 bits; otherwise, the
odd parity bit is 0.
For example, for a user with user ID of 123456789, the enrolled card number is
49
iFace Series User Manual
ZKTechnologyEU
0013378512 and the failed ID is set to 1.
1) When the output is set to “User ID”, the Wiegand output is as follows upon
successful verification:
0000001110101101111001101000101011
Even parity bit
User ID = Binary code of 123456789
Odd parity bit
2) When the output is set to “Card Number”, the Wiegand output is as follows upon
successful verification:
0000000001100110000100011110100001
Even parity bit
User ID = Binary code of 0013378512
Odd parity bit
3) The Wiegand output is as follows upon verification failure:
0000000000000000000000000000000010
Even parity bit
Failed ID = Binary code of 1
Odd parity bit
4.6.3 Customized Format
Apart from the two built-in formats Wiegand 26-bits and Wiegand 34-bits, the
system also supports the format customization function to meet individualized
requirements.
The customized format consists of two character strings: the data bits and parity
bits. These two character strings need to be defined separately. Data bits define the
number of binary bits output by Wiegand as well as the meaning of each bit. The
data bits output by Wiegand can be a card number (C), site code (s), facility code (f),
manufacturer code (m) and parity bits (p). Parity bits define the check mode of each
bit in data bits and ensure the correctness of data bits during transfer through the
parity check. The parity bits can be set to odd check (o), even check (e) and both
odd check and even check (b). There exists a one-to-one correspondence
50
iFace Series User Manual
ZKTechnologyEU
relationship between the data bits and parity bits.
For example, the Wiegand26 can be customized as follows:
Definition of data bits: pssssssssccccccccccccccccp
Definition of parity bits: eeeeeeeeeeeeeooooooooooooo
Note: Wiegand26 consists of 26 bits. The first bit is the even parity bit of bits 2
th
to 13; the 26 bit is the odd parity bit of bits 14 to 25; the second to the ninth
th
th
bits are the site code; the 10 to the 25 bits are the card number.
For details about the Wiegand protocol, see Appendix 3 Introduction to Wiegand.
To customize Wiegand format, proceed as follows:
1)
Select [Define Format] and the [Set] key is then enabled.
2)
Press [Set] to display the [User Define Format] interface, as shown in the
following figure:
3)
Click the entry box below “Card Format” to display the following interface:
Display input in real-time
Backspace
Display the number of
bits in real-time
Cancel Input
Confirm Input
Clear Input
Characters used to define data bits and their meanings:
c: indicates the card number, that is, the output contents, it can be set to
User ID/Card Number through menu operations.
51
iFace Series User Manual
ZKTechnologyEU
f: indicates the facility code which is 0 by default. It is not configurable. To
modify it, please contact the equipment supplier.
m: indicates the manufacturer code which is 0 by default. It is not
configurable. To modify it, please contact the equipment supplier.
p: indicates the parity position.
s: indicates the site code which can be set from 0 to 255 by default.
4)
Click the entry box below “Parity Format” to display the following interface:
Characters used to define parity bits and their meanings:
o: indicates the odd check, that is, there is an odd number of 1’s in the bit
sequence (including one parity bit). For example, for 1000110(0), the
parity bit is 0 and there are already three 1’s. After 0 is suffixed to 1000110,
there is still an odd number of 1’s.
e: indicates the even check, that is, there is an even number of 1’s in the
bit sequence (including one parity bit). For example, for 1000110(1), the
parity bit is 1 and there are already three 1’s. After 1 is suffixed to 1000110,
there is an even number of 1’s.
b: indicates both odd check and even check.
52
iFace Series User Manual
ZKTechnologyEU
For example: Definitions of several universal Wiegand formats.
Wiegand34
Data bits:
pccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeooooooooooooooooo
Note: Wiegand34 consists of 34 bits. The first bit is the even parity bit of
th
bits 2 to 17; the 34 bit is the odd parity bit of bits 18 to 33; the second to
th
th
the ninth bits are the site code; the 10 to the 25 bits are the card
number.
Wiegand37a
Data bits: pmmmmsssssssssssscccccccccccccccccccp
Parity bits: oeobeobeobeobeobeobeobeobeobeobeobeoe
Note: Wiegand37a consists of 37 bits. The first bit is the odd parity bit of bits 3,
4, 6, 7, 9, 10, 12, 13, 15, 16, 18, 19, 21, 22, 24, 25, 27, 28, 30, 31, 33, 34 and
th
36; the 37 bit is the odd parity bit of bits 2, 4, 5, 7, 8, 10, 11, 13, 14, 16, 17, 19,
20, 22, 23, 25, 26, 28, 29, 31, 32, 34 and 35; bits 4, 7, 10, 13, 16, 19, 22, 25, 28,
31 and 34 participate in both odd and even parity check. Bits 2 to 5 are
manufacturer code; bits 6 to 17 are the site code; bits 18 to 36 are the card
number.
Wiegand37
Data bits:
pmmmffffffffffssssssccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeooooooooooooooooooo
Note: Wiegand37 consists of 37 bits. The first bit is the even parity bit of bits 2
53
iFace Series User Manual
ZKTechnologyEU
th
to 18; the 34 bit is the odd parity bit of bits 19 to 36; the second to the fourth
th
th
bits are the manufacturer code; the 5 to the 14 bits are facilitate code; the
th
th
st
th
15 to the 20 bits are the site code; the 21 to the 36 bits are the card
number.
Wiegand50
Data bits: pssssssssssssssssccccccccccccccccccccccccccccccccp
Parity bits:
eeeeeeeeeeeeeeeeeeeeeeeeeooooooooooooooooooooooooo
Note: Wiegand50 consists of 50 bits. The first bit is the even parity bit of bits 2
th
th
to 25; the 50 bit is the odd parity bit of bits 26 to 49; the second to the 16 bits
th
th
are the site code; the 17 to the 49 bits are the card number.
54
iFace Series User Manual
ZKTechnologyEU
5. System Configuration
Through the [System] menu, you can set system-related parameters, including the
basic parameters, interface parameters, fingerprint, facial and attendance
parameters, to enable the terminal to meet user requirements to the greatest extent
in terms of functions and display.
5.1 Basic Parameters
Date/Time: This parameter is used to set the date and time of the FFR terminal.
Date Format: This parameter is used to set the format of the date displayed on the
initial interface of the FFR terminal.
Keyboard Beep: This parameter is used to set whether to generate beep sound in
response to every keyboard touch. Select “ON” to enable the beep sound, and select
“OFF” to mute.
Voice: This parameter is used to set whether to play voice prompts during the
operation of the FFR terminal. Select “ON” to enable the voice prompt, and select
55
iFace Series User Manual
ZKTechnologyEU
“OFF” to mute.
Volume (%): This parameter is used to adjust the volume of voice prompts.
Power Key: This parameter is used to set whether to lock the power key. Select
“ON” to disable the power key. If you select “OFF” and press the power key, the FFR
terminal will be shut down in three seconds.
5.2 Interface Parameters
Language: This parameter is used to display the current language used by the FFR
terminal. For multilingual-capable FFR terminals, you can switch between different
languages through this parameter.
Display Style: This parameter is used to set the time display mode of the initial
interface. Select “ON” to adopt the 24-hour display mode. Select “OFF” to adopt the
12-hour display mode.
Toolbar Style: This parameter is used to display style of the shortcut keys on the
initial interface. It can be set to “Auto Hide” and “Permanent Display”. By selecting
“Auto Hide”, you can manually display or hide the toolbar. By selecting “Permanent
Display”, you can permanently display the toolbar on the initial interface.
Default Verify Mode: This parameter is used to set the default verification mode, that
is, the "Fingerprint" or “Face” verification mode.
Picture Delay (S): This parameter is used to set the picture cycle interval (value
scope: 3─999 seconds).
Sleep Time (S): This parameter is used to specify a period after which the FFR
terminal is put in sleep mode if not operated within this period. You can bring up the
56
iFace Series User Manual
ZKTechnologyEU
FFR terminal from sleep by pressing any key or touching the screen.
5.3 Fingerprint Parameters
1: 1 Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
1: N Threshold: This parameter is used to set the threshold of matching between
current fingerprint and the fingerprint template enrolled in the FFR terminal in the 1:N
verification mode. If the similarity between current fingerprint and the fingerprint
template enrolled in the FFR terminal is larger than this threshold, the matching is
successful; otherwise, the matching is not successful.
The recommended thresholds are as follows:
57
iFace Series User Manual
ZKTechnologyEU
Threshold
False
Rejection
Rate
False
1: N
1:1
(FRR)
Acceptance
Rate (FAR)
High
Low
45
25
Medium
Medium
35
15
Low
High
25
10
1:1 Retry Times: This parameter is used to set the retry times in the event of failure
of 1:1 verification or password verification due to absence of fingerprint enrollment or
improper finger placement, so as to avoid repetitive operations.
Algorithm Version: This parameter is used to select the fingerprint algorithm
version between 9.0 and 10.0. Please select the algorithm version with caution
because the fingerprint templates of these two algorithm versions are incompatible.
Fingerprint Image: This parameter is used to set whether to display the fingerprint
image on the screen during fingerprint enrollment or comparison. It has two values:
Permanent Display and No Display.
5.4 Face Parameters
1: 1 Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1:1
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
58
iFace Series User Manual
ZKTechnologyEU
otherwise, the matching is not successful. The valid value scope is 55─120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
1:1: N Threshold: This parameter is used to set the threshold of matching between
current face and the facial template enrolled in the FFR terminal in the 1:N
verification mode. If the similarity between current face and the facial template
enrolled in the FFR terminal is larger than this threshold, the matching is successful;
otherwise, the matching is not successful. The valid value scope is 65─120. The
higher the threshold, the lower the FAR and the higher the FRR, and vice versa.
The recommended thresholds are as follows:
FRR
High
FAR
1: N
Low
Medium
Low
Threshold
90
Medium
High
1:1
80
80
75
70
65
Enroll Mode: This parameter is used to select the facial enrollment mode between
“Combined Enroll” and “Face”. In the “Combined Enroll” mode, users need to enroll
their fingerprints or passwords after facial enrollment; in the “Face” mode, users only
need to enroll their facial images. The “Face” mode is unavailable for the
administrators because the “Combined Enroll” mode is mandatory for them by
default.
Exposure: This parameter is used to set the exposure value of the camera.
Gain: This parameter is used to set the gain value of the camera.
Quality: This parameter is used to set a quality threshold for the facial images
obtained. The FFR terminal accepts the facial images and processes them by
adopting the facial algorithm when their quality is higher than the threshold;
otherwise, it filters these facial images.
Algorithm Version: Face Algorithm can choose 5.0Algorithm or 7.0Algorithm.
Note: Improper adjustment of the Exposure, Gain and Quality parameters may
59
iFace Series User Manual
ZKTechnologyEU
severely affect the performance of the FFR terminal. Please adjust the
Exposure parameter only under the guidance of the after-sales service
personnel from our company.
5.5 Log Settings
Log Alert: When the available space is insufficient to store the specified number of
attendance records, the FFR terminal will automatically generate an alarm. (Value
scope: 1─99)
Dup. Punch Period (m): If a user’s attendance record already exists and the user
punches in again within the specified period (unit: minute), his/her second
attendance record will not be stored. (Value scope: 1─60 minutes)
Workcode Mode: This parameter is used to select the work code input mode among
Mode 1, Mode 2 and None during attendance verification. If you select Mode 1, the
attendance verification starts after you input the work code on the initial interface; if
you select Mode 2, the attendance verification starts before you input the work code
on the initial interface; if you select None, you do not need to input the work code
during attendance verification on the initial interface. For the input of the work code,
see 6.2 Workcode.
Card Only: If this parameter is set to “YES”, you pass the verification only after card
verification. If this parameter is set to “NO”, you need to verify your face or fingerprint
after card verification.
60
iFace Series User Manual
ZKTechnologyEU
5.6 Update
You can upgrade the firmware program of the FFR terminal by using the upgrade file
in the USB disk through this parameter.
If you need the firmware upgrade file, please contact our technical
support personnel. Generally the firmware upgrade is not
recommended.
61
iFace Series User Manual
ZKTechnologyEU
6. Data Management
Through the [Data Mgt.] menu, you can perform management of data stored on the
FFR terminal, for example, deleting the attendance record, all data and promotional
pictures, purging management rights and resetting the FFR terminal to factory
defaults.
Delete Transactions: Delete all the attendance records.
Delete All Data: Delete all the information of enrolled personnel, including their
fingerprints, facial images and attendance records.
Clear Administrator: Change all administrators to ordinary users.
Delete Picture: Purge the promotional pictures uploaded from USB disks to the FFR
terminal. (For details on how to upload promotional pictures, see “5.4 Upload
Picture”.)
Restore to Factory Settings: Restore all parameter settings on the FFR terminal to
factory settings.
Record: Query the attendance records of employees within a specified time range.
WorkCode: Add, edit or delete the work codes of employees.
SMS: Checking about message.
The employee information and attendance records
will not be deleted during restoration to factory
settings.
62
iFace Series User Manual
ZKTechnologyEU
6.1 Query a Record
After check-in successfully, the employee’s attendance records are saved in the FFR
terminal. You can easily query these attendance records.
User ID: Enter the user ID of the employee to query. If this field is left blank, you can
query the attendance records of all the employees. If you enter a user ID, you can
query the attendance record of the employee with this user ID.
Query Time Period: Select a time period to query, including the customized time
period, yesterday, this week, last week, this month, last month, and all time periods.
Start and End: When you select a customized time period, you need to input a start
time and an end time. When you select other options for time period, the start and
end time will be automatically adjusted to the related time.
After setting the query conditions, press [Query]
and the records that meet the specified query
conditions will be displayed on screen.
Select the row where the desired record is
located, you can query the detailed information
of this record, for example, the detailed
attendance record of the employee with user ID
th
2 on January 7 .
63
iFace Series User Manual
ZKTechnologyEU
6.2 Work Code
Employees’ salaries are subject to their attendance records. Employees may be
engaged in different types of work which may vary with time periods. Considering the
salaries vary with work types, the FFR terminal provides a parameter to indicate the
corresponding work type for every attendance record
to facilitate rapid
understanding of different attendance situations during the handling of attendance
data.
1.
Add a work code
1) Press [Add] on the [WorkCode]
interface (as shown in Figure 1 on the
right) to display the [Add] interface.
No.: A digital code of the work code.
Label: The meaning of the work code.
2) Press the corresponding entry button
of [No.] on the [Add] interface (as shown
in Figure 2 on the right) to display the
No. entry interface. On this interface,
enter a No.
3) Press the corresponding entry button
of [Label] on the [WorkCode] interface
(as shown in Figure 3 on the right) to
display the text entry interface. On this
interface, enter a label of work code.
(See Appendix 1 Text Entry Operation
Instruction)
64
iFace Series User Manual
2.
ZKTechnologyEU
Edit and delete a work code
1) Press the row of a work code on the
[WorkCode] interface (as shown in
Figure 1 on the right) to display the [Edit]
interface.
2) To edit this work code, enter a new
No. and label with the same operation
steps as described in “Add a work
code”.
3) To delete this work code, press
[Delete] (as shown in Figure 3 on the
right).
4) On the displayed prompt interface,
press <YES> to confirm the deletion of
this work code, and press <NO> to
cancel the deletion operation (as shown
in Figure 4 on the right).
65
iFace Series User Manual
ZKTechnologyEU
6.3 SMS *
SMS is similar to notice. The operator can edit the notice content in advance and make it
into SMS displayed on the screen. SMS includes common SMS and individual SMS. If
common SMS is set, SMS will be displayed in main interface in the specified time. If
individual SMS is set, the employee who can receive SMS can see SMS after successful
attendance.
Operation
Notice: The picture may be different from your device. The real product prevails.
6.3.1 Set Message
1)add SMS
Start time: The time when SMS comes into effect
Valid[minute]: SMS appears in the effective time. After the effective time, it won’t appear.
Information type:
Personal: SMS aimed at individual only
Public: SMS able to be seen by all employees
Reserved: Preset SMS, no difference of individual SMS or common SMS.
Operation:
66
iFace Series User Manual
ZKTechnologyEU
When the cursor is on the text box, press shortcut to enable T9 input, input SMS content.
Show below:
(1)If the selected type is individual SMS, Assign is usable. Here, it is to distribute
individual SMS to employee:
Press on the UserID to search employee.
Press “page down & page up” to search employee.
Press on
the employee will select it, and SMS will be distributed to him.
Press
button to save it and then exit.
Notice: 1. If exit without selecting any employee, the SMS type will become preset.
2. If nobody is selected, it will show a warning " Please choose user! " when
assign or save the message.
67
iFace Series User Manual
ZKTechnologyEU
2) If the selected type is common SMS or preset SMS, Assign cannot be used. After
setting, press menu to save it and return to SMS list.
2. Edit SMS
Press on the message show below to select “edit”, and SMS can be edited. The operation
is the same with that of add SMS.
3. Delete SMS
Press the
button to select “delete”, and the selected SMS can be deleted. At
the same time, all information related with this record can be cleared. Show below:
6.3.2 Employee Check Message
1) check common SMS
When the device is in standby state, the main interface will display pictures and current
effective common SMS content in cycle. The display time interval is the same with that of
68
iFace Series User Manual
ZKTechnologyEU
picture display.
2)check individual SMS
When user passes verification, if the user has SMS, the SMS content will be displayed.
The information display time length is 30 seconds. During this period, user verification
can be done. Close the current display to enter verification interface.
7. USB Disk Management
Through the [Dn/Upload] menu, you can import user information and attendance data
stored in a USB disk to related software or other fingerprint recognition equipment.
Download Transactions: Import all the attendance data from the FFR terminal to a USB
disk.
69
iFace Series User Manual
ZKTechnologyEU
Download User: Import all the user information, fingerprints and facial images from the
FFR terminal to a USB disk.
Download user photos*: Import the employees’ photos from the FFR terminal to a USB
disk.
Download Message: Import the message from the FFR terminal to a USB disk.
Only several types of the FFR terminals support the
download of user photos.
Upload User: Upload the user information, fingerprints and facial images stored in a USB
disk to the FFR terminal.
Upload User: Upload the message stored in a USB disk to the FFR terminal.
Upload User Photo: Upload the JPG documents that are named after the user IDs and
stored in a USB disk to the FFR terminal, so that user photos can be displayed after the
employees pass the verification. See Appendix 4 Photo ID Function.
Upload Picture: Upload the JPG documents with “ad_” as initial letters of document
names stored in a USB disk to the FFR terminal. After the upload, these pictures can be
displayed on the initial interface of the FFR terminal. (For details on picture specifications,
see Appendix 2.)
70
iFace Series User Manual
ZKTechnologyEU
8. Keyboard Definitions
You can define six shortcut keys as attendance status shortcut keys or functional
shortcut keys. On the main interface of the FFR terminal, press corresponding keys
and the attendance status will be displayed or the function interface will be rapidly
displayed.
1.
Press [Keyboard] on the main menu
interface
to
display
the
[Keyboard]
interface, as shown in Figure 1 on the right.
2.
All the defined shortcut keys and their
functions are listed on the [Keyboard]
interface (as shown in Figure 2 on the
right). Press [Add] to display the shortcut
key adding interface. Press a shortcut key
in the list to display the shortcut key
editing interface.
3.
Add and edit the functional introduction of
interface
Shortcut Key: Options include: F1–F6.
Note: When the FFR terminal supports
both fingerprint and face recognition
modes, F6 is defined as a recognition
mode switch key by default and cannot
be modified.
Function: You can set the functions of
71
iFace Series User Manual
ZKTechnologyEU
different shortcut keys, such as functional shortcut keys, attendance status
shortcut key and work code shortcut key.
Functional shortcut status include: 1:1/1:G, Face Group No.1, Face Group
No.2, Face Group No.3, Face Group No.4 and Face Group No.5. The setting
interface is shown in Figure 3 on the right.
The
status
shortcut
Check-In,
Check-Out,
Overtime
Check-In,
keys
include:
Leave,
and
Back,
Overtime
Check-Out. The setting interface is
shown in Figure 4 on the right. When
setting the attendance status shortcut
keys, you can also set the “Auto Switch” parameter. When “Auto Switch” is
enabled, the FFR terminal automatically switches the attendance status at the
specified time. The “Auto Switch” setting
interface is as shown in Figure 5 on the
right.
The work code shortcut key setting
interface is as shown in Figure 6 on the
right.
72
iFace Series User Manual
ZKTechnologyEU
9 Auto Test
The auto test enables the system to automatically test whether functions of various
modules are normal, including the screen, collector, voice, facial, keyboard and
clock tests.
Screen Test: The FFR terminal automatically tests the display effect of the color
TFT display by displaying full color, pure white and pure black and checks whether
the screen displays properly. You can continue the test by touching the screen or
exit it by pressing [Auto Test].
Voice Test: The FFR terminal automatically tests whether the voice files are
complete and the voice quality is good by playing the voice files stored in the
terminal. You can continue the test by touching the screen or exit it by pressing [Auto
Test].
Keyboard Test: The FFR terminal tests whether every key on the keyboard works
normally. Press any key on the [Keyboard Test] interface to check whether the
pressed key matches the key displayed on screen. The keys are dark-gray before
pressed, and turn blue after pressed. Press [Auto Test] to exit the test.
Fingerprint Test: The FFR terminal automatically tests whether the fingerprint
collector works properly by checking whether the fingerprint images are clear and
acceptable. When the user places his/her finger in the fingered guide, the collected
fingerprint image is displayed on the screen in real-time. Press [Auto Test] to exit the
test.
73
iFace Series User Manual
ZKTechnologyEU
Face Test: The FFR terminal automatically tests whether the camera works properly
by checking whether the collected facial images are clear and acceptable. Press
[Auto Test] to exit the test.
Time Test: The FFR terminal tests whether its clock works properly by checking the
stopwatch of the clock. Touch the screen to start counting, and touch it again to stop
to check whether the counting is accurate. Press [Auto Test] to exit the test.
74
iFace Series User Manual
ZKTechnologyEU
10 Screen Calibration
You can perform all the menu operations by touching the screen with one of your
fingers or a touch pen. When the touch screen is less sensitive to the touch, you can
perform screen calibration through menu operations.
1.
Press [Menu] on the initial interface to
display the main menu interface.
2.
Press [Calibration] on the main menu
interface to display the screen calibration
interface.
3.
Touch the center of the cross “+”.
4.
Repeat Step 3 following the move of the
“+” icon to different locations on the
screen.
5.
Touch the center of the cross at five
locations on the screen correctly. When
the message “Calibrating screen, pls
wait……” is displayed on screen, the
calibration succeeds and the system
automatically returns to the main menu.
If the calibration fails, the system will request recalibration starting from Step 3.
75
iFace Series User Manual
ZKTechnologyEU
11 Bell Setting
Lots of companies need to ring their bells to signal the start and end of work shifts,
and they usually manually ring their bells or use electric bells. To lower costs and
facilitate management, we integrate the time bell function into the FFR terminal. You
can set the alarm time and duration for ringing the bell based on your requirements,
so that the FFR terminal will automatically play the selected ring tone and trigger the
relay at the alarm time, and stop playing the ring tone after the set duration.
Press [Bell] on the main menu interface to
display the bell setting interface, as shown in
Figure 1 on the right.
1. Add a bell
1)
The displayed bell setting interface (as
shown in Figure 2 on the right) lists all
the bells. Click [Add] to display the [Add]
interface.
2)
On the [Add] interface, set the following
parameters:
Bell Time: This parameter is used to
set a time point when the FFR terminal
automatically plays a bell ring tone
everyday.
Ring Tone: This parameter is used to set the bell ring tone.
Volume: This parameter is used to set the volume of ring tone.
Repeat: This parameter is used to set the alarm times.
76
iFace Series User Manual
ZKTechnologyEU
State: This parameter is used to set whether to enable the bell.
Bell Type: You can select between internal ringing or external ringing. For
internal ringing, the ring tone is played by the loudspeaker of the FFR terminal.
For external ringing, the ring tone is played by an external electric bell that is
wired with the FFR terminal.
Notice: Only some models have external ringing options.
The alarm sounds of the bell and the access control cannot be
concurrently generated by the loudspeaker of the FFR terminal or
externally connected relay. Therefore, when the bell is set to the
external ringing mode, the access limit alarm will automatically
change to the internal ringing mode, and vice versa.
2.
Edit and delete a bell
Press a bell in the list on the bell setting
interface to display the [Edit] interface,
with the similar operation as “Add a
bell”.
Press [Delete] on the [Edit] interface
and the system displays a prompt
window as shown in the figure on the
right. In the prompt window, press
<YES> to delete the current bell and
<NO> to cancel the deletion.
77
iFace Series User Manual
ZKTechnologyEU
12 Access Control Setting *
Through the [Access] menu, you can set the parameters of the electronic locks and
related access control devices.
Time Zone Set: Is the definition of everyday Time period that can unlock door in one week;
Lock Control Para: setting the Lock Delay[s], Door Sensor Delay[s] and alarm
Delay[s] Para, show below:
(1). Lock Delay[s]: Fingerprint scanner controls the time to open electronic lock.
(Functioning value for 1~10)-the language document apply(second) behind and
check all language documents.
(2). Door Sensor Delay[s]: Some segment time which begin after open door just
begin alarm; (The functioning value is 1~99)
(3). Door Sensor Mode: there are three option that is none( NONE), normal open
(NO), normal close(NC) .the none means the door Sensor doesn’t apply, Normal
Open is defined that Thee door can be set to a Passage Mode in the normal
78
iFace Series User Manual
ZKTechnologyEU
condition, Normal Close means that the door is close in the normal work condition.
Holiday Set: Set special access control time during holiday.
TimeZone Control Para: Can set the NC Time Zone and NO Time Zone, show
below:
Group Settings: Set TimeZone as group.
Duress Alarm Parameter: include 1:1 Trigger, 1:N Trigger Alarm Delasy and
Password Trigger setup item, show below.
Unlock combination Setting: defines different unlocking combinations, each
combination is composed of different groups.
Anti-Passback Setting: APB Direction setting, can set as APB-Out, APB-In,
APB-Out/In and None; Local Status can set as Exit Control, Entry Control and
None. Show below:
79
iFace Series User Manual
ZKTechnologyEU
13 Date/Time Setting
13.1 Set Date/Time
The date and time of the FFR terminal must be set accurately to ensure the accuracy
of attendance time.
1.
Press [Menu] on the initial interface to
display the main menu interface.
2.
Press [Time/Date] on the main menu
interface to
display the time setting
interface.
3.
Select the desired date and time by
pressing ▲ or ▼, or enter the related
values into the date and time entry boxes
through the keyboard (as shown in Figures
3 and 4 on the right).
4.
Press [Save] to save current information
and return to the previous interface. Press
[Cancel] to return to the previous interface
without saving current information.
80
iFace Series User Manual
ZKTechnologyEU
13.2 Set Daylight Saving Time (DST)
The Daylight Saving Time (DST) is a widely used system of adjusting the official
local time forward to save energy. The uniform time adopted during the
implementation of this system is known as the DST. Typically clocks are adjusted
forward one hour in the summer to make people early to bed and early to rise so as
to make full use of illumination resources and save electricity. Clocks are adjusted
backward in autumn. The specific DST regulations vary with countries.
To meet the DST requirement, the FFR terminal supports the DST function to adjust
forward on hour at ×× (Hour): ×× (Minute) ×× (Day) ×× (Month) and backward one
hour at ×× (Hour): ×× (Minute) ×× (Day) ×× (Month).
1.
Press [Menu] on the initial interface to
display the main menu interface.
2.
Press [Time/Date] on the main menu
interface to display the time setting
interface.
3.
Press [DLST] on the time setting
interface to display the DST setting
interface.
81
iFace Series User Manual
4.
ZKTechnologyEU
Set the following parameters on the
DST setting interface:
DST Settings: This parameter is used
to enable or disable the DST.
Mode: You can select between Mode 1
and Mode 2.
In Mode 1 (the default mode), the DST
is set in the “Month-Day Hour: Minute”
format; in Mode 2, the DST is set in the
“Month-Week-Day
Hour:
Minute”
format.
The value scope of week (WS): 1 – 6. 1
means the first week, 2 the second
week and so on and so forth. The value scope of day (WK): 0 – 6. 0 means
Sunday, 1 means Monday and so on and so forth.
Start and End: These two parameters are respectively used to set the start
and end time of the DST.
st
For example, adjust the clock forward one hour at 08: 00 on April 1 , and
st
backward one hour at 08: 00 on October 1 .
5.
After setting the DST, press [Done] to
return to the time setting interface.
Press [Save] on the time setting
interface to save current settings and
return to the previous interface; press
[Cancel] to directly return to previous
interface without saving current information.
82
iFace Series User Manual
ZKTechnologyEU
14 System Information
You can check the storage status as well as version information of the FFR terminal
through the [System Information] option.
14.1 Records
The number of enrolled users, administrators and passwords is displayed on the
[Records] interface; the total fingerprint storage capacity and occupied capacity as
well as the total attendance storage capacity and occupied capacity are graphically
displayed respectively, as shown in the following figure:
83
iFace Series User Manual
ZKTechnologyEU
14.2 Terminal
The terminal name, serial number, version information, vendor and date of
manufacture are displayed on the [Terminal] interface.
84
iFace Series User Manual
ZKTechnologyEU
Appendix
Appendix 1 Text Input Instructions
The FFR terminal supports the input of Chinese and English characters, numbers
and symbols. Press related button to input text. For example, press [Name] to
display the text input interface, as shown in the following figure:
Keyboard Area
Text Display Area
Text List Area
Exit
Delete
Enter
Space
Chinese/English Switch Key
Character/Number Switch Key
Upper/Lower Case Switch Key
85
iFace Series User Manual
ZKTechnologyEU
To enter a name, proceed as follows:
1.
2.
Press [Name] on the [Add] interface, as show below.
Enter the Pinyin characters, and a list of
Chinese characters in relation to the Pinyin is
presented in the text display area, as shown in
Figure 1 on the right.
3.
If the desired character is displayed in the text
display area, press this character. And this
character is at the same time displayed on the
[Name] button, as shown in Figure 2 on the
right. Enter next character by repeating Step 2.
4.
After finishing the entry of name, press [X] to
exit keyboard interface and return to the previous interface.
86
iFace Series User Manual
ZKTechnologyEU
Appendix 2 Rules for Uploading Promotional Pictures
1.
All pictures must be in JPG format as other formats are not supported.
2.
The file name of a promotional picture must be ad_0 - ad_9. For example,
ad_1.jpg is a valid file name.
3.
After a picture is uploaded to the FFR terminal, its name does not change. To
replace this picture, you need to upload a new picture with the same file name to
overwrite it.
4.
The size of each picture cannot exceed 20K; otherwise, the upload will be
unsuccessful.
5.
The recommended resolution of the picture is 320 × 240. Pictures with
resolution higher or lower than 320 × 240 are not recommended.
6.
A maximum of 10 promotion pictures can be uploaded.
87
iFace Series User Manual
ZKTechnologyEU
Appendix 3 Introduction to Wiegand
Wiegand26 is an access control standard protocol established by the Access Control
Standard Subcommittee affiliated to the Security Industry Association (SIA). It is a
non-contact IC card reader interface and output protocol.
Wiegand26 defines the interface between the card reader and controller used in the
access control, security and other related industrial fields. Wiegand26 helps
standardize the work of the card reader designers and controller manufacturers. The
access control products manufactured by our company are also designed by
following this protocol.
Digital Signals
Figure 1 is a sequence diagram in which the card reader sends digital signals in bit
format to the access controller. In this sequence diagram, Wiegand follows the SIA’s
access control standard protocol for the 26-bit Wiegand card reader (one pulse time
ranges between 20us and 100us, and the pulse jump time ranges between 200us
and 20ms). Data1 and Data0 are high level (larger than Voh) signals till the card
reader prepares to send a data stream. The asynchronous low-level pulse (smaller
than Vol) generated by the card reader is sent to the access control panel (The
saw-tooth wave as shown in Figure 1) through Data1 or Data0. Data1 and Data0
pulses will neither overlap nor be generated synchronously. Table 1 lists the
maximum and minimum pulse width (a consecutive pulse) and pulse jump time (time
between pulses) allowed by the F series fingerprint access control terminal.
Table 1 Pulse Time
Symbol
Definition
Typical Value of Reader
Tpw
Pulse Width
100 µs
Tpi
Pulse Interval
1 ms
88
iFace Series User Manual
ZKTechnologyEU
Figure 1 Sequence Diagram
Appendix 4 Photo ID Function
Some FFR terminals also support the Photo ID function. The Photo ID function is
used to display the photo enrolled by a user or stored in a USB disk on the screen in
addition to such information as the user ID and name.
[Operation Steps]
1.
When the photo taken by the FFR terminal is used, the photo can be displayed
upon successful verification.
2.
To use a photo stored in a USB disk, proceed as follows:
1) Create a folder with the name of “photo” in the USB disk, and store users'
2)
photos under this folder.
The user photos must be in JPG format and named after their IDs. For
example, for the user with user ID of 154, the photo name must be
154.jpg.
3)
Insert the USB disk into USB slot on the FFR terminal, and select USB
Disk Management -> Upload -> Upload Photos. Then user photos can be
displayed upon successful verification.
Note: 1) The length of a user name cannot exceed 24 digits.
89
iFace Series User Manual
ZKTechnologyEU
2) The recommended size of a user photo is less than 30K.
3) The uploaded new user photo will overwrite the existing photo in
related to the user ID.
4)
To download user photos, select USB Disk Management -> Download ->
Download User Photos. A folder with the name of “photo” will be
automatically created on the USB disk, and all downloaded user photos
are stored under this folder.
90
iFace Series User Manual
ZKTechnologyEU
Appendix 5 Attendance Status Selection Function *
Some FFR terminals also support the attendance status selection function which
requires users to select attendance status prior to verification. If verification is
performed without selection of the attendance status, the record is “No Work Status”,
that is, the record is not used as the attendance record, as shown in the following
figure:
You cannot set the timed status switch function on the FFR
terminal capable of attendance status selection.
91
iFace Series User Manual
ZKTechnologyEU
Appendix 6 Anti-pass back *
[overview]
Sometimes, some illegal person follows the employee into the gate, which will bring
security problem. To prevent such risk, this function is enabled. In record must match
out record, or the gate won’t be open.
This function needs two machines to work together. One is installed inside the door
(master machine hereinafter), the other is installed outside the door (slave machine
hereinafter). Wigand signal communication is adopted between the two machines.
[working principle]
The master machine has Wigand In and slave machine has Wigand Out. Connect
Wigand Out of slave machine to Wigand In of master machine. Wigand output from
slave machine must not own machine ID. The number sent to master machine from
slave machine must be found in the master machine.
[function]
Judge whether it is anti-pass back according to user’s recent in-out record. In record
92
iFace Series User Manual
ZKTechnologyEU
and out record must be matched. This machine supports out, in, or out-in anti-pass
back (enter machine menu—setting—system setting—advanced setting—anti-pass
back).
When master machine is set as “out anti-pass back”,if user wants to come in and go
out normally, his recent record must be “in”, or he cannot go out. Any “out” record will
be “anti-pass back refused”. For example, a user’s recent record is “in”, his second
record can be “out” or “in”. His third record is based on his second record. Out record
and in record must match.(Notice: if customer has no record before, then he can
come in but cannot go out. )
When the master machine is set as “in anti-pass back”,if the user wants to come in
and go out normally, his recent record must be “out”, or he cannot go out. Any out
record will be “anti-pass back refused” by the system. (Notice: if the customer has
no former record, then he can go out, but cannot come in. )
When the master machine is set as “out-in anti-pass back”,if the user wants to come
in and go out normally, if his recent record is “out” and “in”, then his next record must
be “ in” and “out”.
[operation]
1) Select model
Master machine: Machine with Wiegand in function, except for F10
Reader.
Slave machine: Machine with Wiegand Out function.
2) Menu setting
Anti-pass back:
There are three options: Out anti-pass back, in anti-pass back and nonanti-pass
back.
out anti-pass back: Only user’s last record is in-record, can the door be open.
in anti-pass back: Only user’s last record is out-record, can the door be open.
Device status
There are three options: Control-in, control-out and none.
93
iFace Series User Manual
ZKTechnologyEU
Control-in: When it is set, the verified record on the device is in-record.
Control-out: When it is set, the verified record on the device is out-record.
None: When it is set, close the device’s anti-pass back function.
Press ▲/▼ to switch the input box. Press
/
to modify setting. Then press save
to save it.
3) modify device’s Wiegand output format
When the two devices are communicating, only Wiegand signals without device ID
are received. Enter device menu->communication option->Wiegand option or
enter software-〉basic setting-〉device management-〉Wiegand,to modify “defined
format” as “wiegand26 without device ID”.
4) enroll user
The user must be on master machine and slave machine at the same time, and user
PIN must be the same. Therefore, it is necessary to enroll user on master machine
and slave machine at the same time.
5) connection instruction
Wiegand communication is adopted for master machine and slave machine. Refer to
the following for connection::
Master
Slave
IND0
<----->
WD0
IND1
<----->
WD1
GND
<----->
GND
94
iFace Series User Manual
ZKTechnologyEU
Appendix 7 Multi- verification methods *
To meet the demand of high security, we have provided multi- verification modes.
Aimed at individual or group setting, various verification types are set. They are the
combinations of PIN,FP, PW and RF, for example: single fingerprint, single password,
ID+FP, FP+PW, FP+PW+card, PIN+FP+PW and so on.
Notice: 1)Mifare can be looked as RF in the real dispose. Only
device with Mifare card function can use it.
2 ) Except for some special models, most devices have only fingerprint
verification and password verification. Only device with Mifare card function has
Mifare card verification.
"/"--- or ,"&"--- and "←"---Enter
The following is the description of user enrolled fingerprint card and the verification
mode with password enrolled.
type
FP
description
Only fingerprint verification
1)PIN+FP(1:1 verification )
2)FP (1:N verification )
3)RF+FP(1:1 match )
PIN
only number verification
1)PIN+“←”
PW
only password
verification
1) PIN+“←”+PW
2) RF+PW
RF
only RF Card verification
1)RF+FP
FP/PW
fingerprint or password verification
95
iFace Series User Manual
ZKTechnologyEU
1)PIN+FP(1:1)
2)FP(1:N)
3)PIN+“←”+PW
4)RF+PW
FP/RF
fingerprint or RF verification
1)PIN+FP(1:1)
2)FP(1:N)
3)RF+FP
PW/RF
password or RF verification
1) RF+FP
2) PIN+“←”+PW
FP/PW/RF
fingerprint or password or RF verification
1) PIN+FP(1:1)
2) FP(1:N)
3) PIN+PW
4) RF+FP
FP&PIN
fingerprint and number verification
1)PIN+“←”+FP(1:1)
2)RF +“←”+FP(1:1)
FP&PW
fingerprint and password verification
1) FP(1:N)+PW+“←”
2) PIN+FP(1:1)+PW+“←”
3) RF+PW +“←”+ FP(1:1)
FP&RF
fingerprint and RF verification
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+FP(1:1)+RF
PW&RF
password and RF verification
96
iFace Series User Manual
ZKTechnologyEU
1) RF+PW
2) PIN+“←”+PW+RF
FP&PW&RF
fingerprint, password and RF verification
1) FP(1:N)+PW+RF
2) PIN+FP(1:1)+PW+RF
3) RF+ PW+ FP(1:1)
FP&PIN&PW
fingerprint,number and password
1) PIN+“←”+PW+FP(1:1)
2) RF+“←”+PW+“←”+FP(1:1)
FP&RF/PIN
Fingerprint and RF verification or fingerprint and
number.
1)RF+FP(1:1)
2)FP(1:N)+RF
3)PIN+“←”+FP(1:1)
If enroll user with fingerprint card or password +card, refer to the following for various
verifications:
type
description
fingerprint enroll
FP
Only
password enroll
fingerprint
verification
1
)
PIN+FP
(
1:1
cannot pass
verification )
2)FP (1:N verification
3)RF+FP(1:1)
PIN
only number verification
1)PIN+“←”
PW
1)PIN+“←”
only password verification
97
iFace Series User Manual
ZKTechnologyEU
password error
1) PIN+“←”+PW
2)RF+PW
RF
Only RF Card verification
1)RF+FP
FP/PW
fingerprint
1)RF
or
password
verification
1) PIN+FP(1:1)
1) PIN+“←”+PW
2) FP(1:N)
2) RF+PW
3) PIN+“←”+ FP(1:1)
4) RF+FP(1:1)
FP/RF
fingerprint
or
RF
verification
1)RF
1) PIN+FP(1:1)
2) FP(1:N)
3) RF+FP
PW/RF
password
or
RF
verification
FP/PW/RF
1) RF
1) PIN+”←”+PW
2) PIN+“←”+RF
2) RF
fingerprint
or
password
or RF verification
1) PIN+FP(1:1)
1) PIN+”←”+PW
2) FP(1:N)
2) RF
3) PIN+“←”+ FP(1:1)
4) RF+FP
FP&PIN
fingerprint
and number
verification
98
iFace Series User Manual
ZKTechnologyEU
cannot pass
1) PIN+“←”+FP(1:1)
2) RF+ PIN+“←”+FP(1:1)
FP&PW
fingerprint
password
and
verification
cannot pass
FP&RF
cannot pass
fingerprint
and
RF
verification
cannot pass
1) RF+FP(1:1)
2) FP(1:N)+RF
3) PIN+FP(1:1)+RF
PW&RF
password
and
RF
verification
cannot pass
1) RF+PW
2) PIN+“←”+PW+RF
FP&PW&RF
fingerprint, password
and
RF verification
cannot pass
FP&PIN&PW
cannot pass
fingerprint,number
and
password
cannot pass
FP&RF/PIN
cannot pass
fingerprint
verification
and
RF
or fingerprint
and number
1)RF+FP(1:1)
cannot pass
2)FP(1:N)+RF
3)PIN+“←”+FP(1:1)

Notice:1)If user enrolls a card and fingerprint at the same time.
99
iFace Series User Manual
ZKTechnologyEU
Only card is needed during RF verification.
2)For combined verification, it is better to use fingerprint
+password to enroll user, or verification will fail.
For example:User A use fingerprint for enrollment, while
password is used for verification, then the user cannot pass the verification.
Appendix 8 GPRS *
General Packet Radio Services (GPRS) is a packet-based wireless communication
service that promises data rates from 56 up to 114 Kbps and continuous connection
to the Internet for mobile phone and computer users. The higher data rates allow
users to take part in video conferences and interact with multimedia Web sites and
similar applications using mobile handheld devices as well as notebook computers.
GPRS is based on Global System for Mobile (GSM) communication and
complements existing services such circuit-switched cellular phone connections and
the Short Message Service (SMS).
We fingerprint machine has also realized the GPRS function. GPRS modules can be
built-in fingerprint machine , also can be an external GPRS module to achieve the
GPRS systems for data transfer.
How to operate GPRS fingerprint machine, please see 4.5 dail-up settings.
Appendix 9 Webserver *
At the first time use the Webserver, should be configure the setting, enter menu ->
communications settings fingerprints IP address, such as set up the IP address of
the fingerprint machine to 192.168.1.225; type the “//192.168.1.225 in IE address bar
100
iFace Series User Manual
ZKTechnologyEU
The default the system user name of super administrator: administrator; Password:
123456.
Enter view records
① Left-click option "View In-Out records" interface;
② to select staff you want to view in the list;
③ designate the time scope for view.
2) Export In –Out records: Save these logs to local disk.
① left click "Export logs" option;
101
iFace Series User Manual
ZKTechnologyEU
② choose staff you want save his records in the list; ③ select file format to save.
④ click "start the download" and save the file to the local disk.
synchronization equipment time
① left click "synch equipment time" option on the interface;
② select the adjustment method
Auto: Time of computer and equipment will be automatically synchronized.
Manual adjustments: manually set the time of the equipment and defined time
synchronization.
③ local equipment date
Choose automatic adjustment, this machine‘s date and time is the computer date.
Choice of manual adjustments can manually enter the time.
④ click the "modified" button to change the time of equipment
communication parameter
① left click "communication parameters" option on interface
102
iFace Series User Manual
ZKTechnologyEU
② enter the communications parameters
• Ethernet:
(1) Through the hub: with cable (for connecting Net cards and hubs) connect
machines to the network.
(2) Directly connection: Use the cross-cable (direct connect the two Ethernet
endpoint) to connect machines and PC .
IP Address: The default IP is 192.168.1.201, you can make changes based on the
actual situation;
Subnet Mask: The default subnet mask 255.255.255.0, you can make changes
based on the actual situation;
Gateway Address: default gateway address 0.0.0.0, you can make changes based
on the actual situation;
• RS232: the use of RS232 serial port.
Baud rate: the communications and computer communications rate, high-speed
communications faster, the proposed use of RS232 communications 115200,57600
the baud rate.
RS232/RS485: whether or not to use RS232 communications, select On the RS232
apply .
• RS485 way
Baud rate: the communications and computer communications rate, low-speed
communication stability, the proposed RS485 communications the baud rate
9600,38400.
RS232/RS485: whether or not to use RS485 communications, select On the way to
use RS485.
103
iFace Series User Manual
ZKTechnologyEU
③ click "Save settings" button to write into the parameters of communications
equipment.
Appendix 10 Statement on Human Rights and Privacy
Dear Customers:
Thank you for choosing the hybrid biometric products designed and manufactured
by us. As a world-renowned provider of biometric technologies and services, we pay
much attention to the compliance with the laws related to human rights and privacy
in every country while constantly performing research and development.
We hereby make the following statements:
1.
All of our multibio recognition devices for civil use only collect the characteristic
points of multibio instead of the multibio images, and therefore no privacy issues
are involved.
2.
The characteristic points of multibio collected by our products cannot be used to
restore the original multibio images, and therefore no privacy issues are
involved.
3.
We, as the equipment provider, shall not be held legally accountable, directly or
indirectly, for any consequences arising due to the use of our products.
4.
For any dispute involving the human rights or privacy when using our products,
please contact your employer directly.
Our multibio products for police use or development tools support the collection of
the original multibio images. As for whether such a type of multibio collection
constitutes an infringement of your privacy, please contact the government or the
final equipment provider. We, as the original equipment manufacturer, shall not be
held legally accountable for any infringement arising thereof.
The law of the People’s Republic of China has the following regulations regarding
the personal freedom:
1.
Unlawful arrest, detention or search of citizens of the People's Republic of
China is prohibited; infringement of individual privacy is prohibited.
104
iFace Series User Manual
ZKTechnologyEU
2.
The personal dignity of citizens of the People's Republic of China is inviolable.
3.
The home of citizens of the People's Republic of China is inviolable.
4.
The freedom and privacy of correspondence of citizens of the People's
Republic of China are protected by law.
At last we stress once again that biometrics, as an advanced recognition technology,
will be applied in a lot of sectors including e-commerce, banking, insurance and legal
affairs. Every year people around the globe suffer from great loss due to the
insecurity of passwords. The biometric products actually provide adequate
protection for your identity under a high security environment.
105
iFace Series User Manual
ZKTechnologyEU
Appendix 11 Environment-Friendly Use Description
The Environment Friendly Use Period (EFUP) marked on this product refers to the
safety period of time in which the product is used under the conditions specified in
the product instructions without leakage of noxious and harmful substances.
The EFUP of this product does not cover the consumable parts that need to be
replaced on a regular basis such as batteries and so on. The EFUP of batteries is
5 years.
Names and Concentration of Toxic and Hazardous Substances or Elements
Toxic and Hazardous Substances or Elements
Parts Name
Pb
Hg
Cd
Cr6+
PBB
PBDE
Chip resistor
×
○
○
○
○
○
Chip capacitor
×
○
○
○
○
○
Chip inductor
×
○
○
○
○
○
Chip diode
×
○
○
○
○
○
ESD components
×
○
○
○
○
○
Buzzer
×
○
○
○
○
○
Adapter
×
○
○
○
○
○
Screws
○
○
○
×
○
○
○: Indicates that this toxic or hazardous substance contained in all of the homogeneous
materials for this part is below the limit requirement in SJ/T11363-2006.
×: Indicates that this toxic or hazardous substance contained in at least one of the
homogeneous materials for this part is above the limit requirement in SJ/T11363-2006.
Note: 80% of the parts in this product are manufactured with non-hazardous
environment-friendly materials. The hazardous substances or elements contained cannot be
replaced with environment-friendly materials at present due to technical or economical
constraints.
106
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement