User Manual

Add to my manuals
118 Pages

advertisement

User Manual | Manualzz

SyncMaster P64FP P64FT

PDP Display

User Manual

The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Note

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock

An administration fee may be charged if either

• (a) an engineer is called out at your request and there is no defect in the product

(i.e. where you have failed to read this user manual).

• (b) you bring the unit to a repair centre and there is no defect in the product

(i.e. where you have failed to read this user manual).

The amount of such administration charge will be advised to you before any work or home visit is carried out.

Power

When not used for extended period of time, set your computer to DPM.

If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power outlet.

• Otherwise, this may result in electric shock or fire.

Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.

• Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

• Otherwise, it may result in electric shock or personal injury.

Ensure that the power plug is plugged into the power outlet firmly and correctly.

• Otherwise, this may result in fire.

Safety Instructions

Do not forcefully bend or pull the power plug and do not place any heavy material on it.

• Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

• Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

• Otherwise, this may result in damage to the product due to electric shock.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

• Otherwise, this may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the provided power cord of another product.

• Otherwise, this may result in fire or electric shock.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

• Otherwise, it may be dropped and cause personal injury, and/or damage the product.

When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA-

RETTES AND ANY HEATING APPLIANCES NEAR THE PROD-

UCT.

• Otherwise, this may result in fire.

Keep heating appliances as far away from the power cord or the product as possible.

• Otherwise, this may result in electric shock or fire.

Clean

Safety Instructions

Do not install it in a badly ventilated location such as a bookcase or closet.

• Otherwise, this may result in fire due to an increase in the internal temperature.

When putting the product down, make sure to put it down softly.

• Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

• Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

• Otherwise, it may fall and cause personal injury.

• Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is a clearance of more than 4 inches (10 cm) from the wall.

• Otherwise, it may result in fire due to an increase in the internal temperature.

Ensure that the packaging vinyl is kept away from children.

• Otherwise, it may result in serious harm (suffocation) if children play with it.

If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.

• This may cause damage to the product or the person carrying it.

When cleaning the PDP Display case or the surface of the TFT-PDP screen, wipe with a slightly moistened, soft fabric..

Do not spray cleaner directly onto the surface of the product.

• Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off.

When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.

• Otherwise, it may result in fire.

When cleaning the product, make sure to disconnect the power cord.

• Otherwise, it may result in electric shock or fire.

Others

Safety Instructions

When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth.

• Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.

• These may change the appearance of the product surface and peel off the indication labels on the product.

Since the product housing is easily scratched, make sure to use the specified cloth only.

When cleaning the product, do not spray water directly onto the main body of the product.

• Ensure that water does not enter the product and that it is not wet.

• Otherwise, this may result in electric shock, fire or a malfunction.

The product is a high voltage product. Do not disassemble, repair or modify the product yourself.

• Otherwise, this may result in electric shock or fire.

• If the product needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service

Center.

• Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.

• Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.

• Otherwise, this may result in electric shock or fire.

If thunder or lightning is occurring, do not touch the power cord or antenna cable.

• Otherwise, this may result in electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Safety Instructions

Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.

• Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or curtain.

• Otherwise, it may result in fire due to an increase in the internal temperature.

Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.

• If water or a foreign material enters the product, disconnect the power cord and contact a Service Center.

• This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the product.

• Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc).

• If water or foreign material enters the product, disconnect the power cord and contact a Service Center.

• Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain may occur.

• If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

• Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

• Having the sound too loud may damage your hearing.

To avoid eyestrain, do not sit too close to the product.

Take a rest for at least five (5) minutes after using the monitor for one

(1) hour.

• This reduces eye fatigue.

Safety Instructions

Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.

• Otherwise, it may fall and cause personal injury and/or damage the product.

• If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.

• Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the product.

• The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the power cord from the power outlet.

• Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.

• Your children may hang onto the product causing it to fall and this may result in personal injury or death.

Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.

• If children have had the battery in their mouths, consult your doctor immediately.

When replacing the battery, insert it with the right polarity (+, -).

• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.

• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.

• The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.

Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.

• This may reduce the lifetime of the product, and may result in fire.

Safety Instructions

Do not drop any objects onto the product or cause any impact to the product.

• Otherwise, this may result in electric shock or fire.

Do not use a humidifier near the product.

• Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug; ventilate immediately.

• If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.

Keep the small accessories in a location out of the reach of children.

Do not install the product in a location low enough for children to reach.

• Otherwise, it may fall and result in personal injury.

• Since the front part of the product is heavy, install the product on a level and stable surface.

Do not put any heavy objects on the product.

• This may result in personal injury and/or damage to the product.

Introduction

Package Contents

Note

Please make sure the following items are included with your PDP Display.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Checking the Contents of the Package

Remove the lock from the package box, as shown in the figure above.

Lift up the package box by holding the grooves on both sides of the package box.

Check the contents of the package.

Remove the Styrofoam and vinyl cover.

Note

• After unpacking the package, make sure to check the contents of the package.

• Make sure to keep the package box for transporting the product in the future.

• After unpacking, you may use the lower part of the package box as a temporary stand for product test or operation check.

Unpacking

Introduction

PDP Display

Manuals

Quick Setup Guide Warranty Card

(Not available in all locations)

Cables

User's Guide

D-Sub Cable

Others

Power Cord

Remote Control

Options (P64FT Model Only)

Batteries (AAA X 2)

(Not available in all locations)

Ferrite Core for Power Cord

Pen battery charger Adapter Power Cord

USB Dongle Zigbee Touch Pen(IWB-P1) Samsung Interactive whiteboard

Introduction

Sold separately

DVI Cable Wall Mount KIT BNC to BNC Cable

Network Box RGB to BNC Cable STEREO Cable

HDMI Cable BNC-COMPONENT Cable COMPOSIT Cable

HDMI-DVI Cable

Warning

• The network box is not compatible with the Interactive Whiteboard program.

Ferrite Core

• The ferrite cores are used to shield the cables from interference.

• When connecting a cable, open the ferrite core and clip it around the cable near the plug.

Your PDP Display

Note

The PDP device may interfere with an amateur radio or AM radio.

Front

Introduction

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the PDP Display at the time.

[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [Component] →

[BNC]

Enter button [ ]

Activates a highlighted menu item.

Note

• This product is not compatible with MagicInfo.

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.

- VOL+

Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.

SEL

Moves from one menu item to another vertically or adjusts selected menu values.

Power button [ ]

Use this button for turning the PDP Display on and off.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the PDP Display.

Introduction

Rear

Note

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The

PDP Display's configuration at the back may vary slightly depending on the PDP Display model.

POWER IN

The power cord plugs into the PDP Display and the wall plug.

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

RGB IN (PC Connection Terminal (Input))

• Use a D-Sub Cable (15 pin D-Sub) - PC mode

(Analog PC)

• Connect the RGB IN port on the monitor to the BNC port on the PC using the RGB to

BNC cable.

DVI IN (PC Video Connection Terminal)

Connect the [DVI IN] port on the monitor to the

DVI port on the PC using the DVI cable.

Introduction

DVI/RGB AUDIO IN(PC/DVI Audio Connection Terminal (Input))

Connect an audio cable to [R-AUDIO-L] on the monitor and the audio out port on the source device.

AV/COMPONENT AUDIO IN [R-AUDIO-L]

Connect an audio cable to [R-AUDIO-L] on the monitor and the audio out port on the source device.

DVI OUT

• Connect a monitor to another monitor through a DVI cable.

• Connect the [DVI OUT] port on the monitor to the [HDMI IN] port on the other monitor using the DVI to HDMI cable.

• DVI, HDMI and network signals sent via the

[DVI OUT] port are displayed on the second display which has the DVI IN port.

AV IN [VIDEO]

Connect the [AV IN (VIDEO)] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.

AUDIO OUT

Headphone/External speaker output terminal.

HDMI IN

Connect the HDMI terminal at the back of your

PDP Display to the HDMI terminal of your digital output device using a HDMI cable.

Up to HDMI cable 1.2 can be supported.

Introduction

BNC OUT [R, G, B, H, V] (BNC Terminal

(Output))

BNC (Analog PC) Connection: connecting the R,

G, B, H, V ports.

The number of PDP Displays that can be connected to the loopout depends on the cables, signal source, etc. With cables or signal source where there is no degradation, up to 10 PDP Displays can be connected (May not be supported depending on the connected cable).

BNC/COMPONENT IN [R/P

R

, G/Y, B/P

B

, H,

V] (BNC/Component Connection Terminal (input))

- During BNC input, please check specifications for the input ports below.

• [R/P

R

] --> Red port input

• [G/Y] --> Green port input

• [B/P

B

] --> Blue port input

- During component input, please check specifications for the input ports below.

• [R/Y] --> Green port input

• [G/P

B

] --> Blue port input

• [B/P

R

] --> Red port input

This product has an internal speaker.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating near the PDP Display , causing a malfunction due to interference with the frequency.

Introduction

POWER

OFF

Number Buttons

1. POWER

2. OFF

3. Number Buttons

4. DEL / GUIDE button

DEL

- VOL +

/ GUIDE button

SOURCE

D.MENU

TOOLS

Up-Down Left-Right buttons

INFO

COLOR BUTTONS

TTX/MIX

MTS/DUAL

ENTER/PRE-CH

MUTE

CH/P

TV

MENU

RETURN

EXIT

MagicInfo

Turns the product On.

Turns the product Off.

Used to enter the password during the OSD adjustment or to use

MagicInfo.

The "-" button is used to select Digital channels.

Electronic Program Guide (EPG) display.

5. - VOL +

6. SOURCE

7. D.MENU

Note

- This button is disabled for this PDP display.

Adjusts the audio volume.

Press this button to switch to MagicInfo or PC mode or a connected external input source.

DTV menu display

Introduction

8. TOOLS

Note

- This button is disabled for this PDP display.

Use to quickly select frequently used functions.

Note

- This button is disabled for this PDP display.

9. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

10. INFO

Current picture information is displayed on the upper left corner of the screen.

11. COLOR BUTTONS Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu.

12. TTX/MIX

Note

- This button is disabled for this PDP display.

TV channels provide written information services via teletext.

- Teletext Buttons

13. MTS/DUAL

14. ENTER/PRE-CH

Note

- This button is disabled for this PDP display.

Note

- This button is disabled for this PDP display.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

FM Stereo

Audio Type MTS/S_Mode

Mono Mono

Stereo

SAP

Mono ↔ Stereo

Mono ↔ SAP

Default

Manual Change

Mono

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM

MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV.

This button is used to return to the immediately previous channel.

Introduction

15. MUTE

16. CH/P

17. TV

18. MENU

Note

- This button is disabled for this PDP display.

Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio comes back on if

MUTE or - VOL + is pressed in the Mute mode.

In TV mode, selects TV channels.

Note

- This button is disabled for this PDP display.

Selects the TV mode directly.

Note

- This button is disabled for this PDP display.

Opens the on-screen menu and exits from the menu or closes the adjustment menu.

Returns to the previous menu.

Exits from the menu screen.

MagicInfo Quick Launch Button.

19. RETURN

20. EXIT

21. MagicInfo

Note

This button is disabled for products that do not support MagicIn-

fo.

User Installation Guide

Note

• Be sure to call an installation expert of Samsung Electronics to install the product.

• The warranty becomes invalid if the product is installed by someone other than a professional authorized by Samsung Electronics.

• A Samsung Electronics service center can provide details.

Tilt Angle and Rotation

1 2

Introduction

1.

The product can be tilted up to 15 degrees from a vertical wall.

2.

To use the product in portrait mode, rotate it clockwise so that the LED indicator is at the bottom.

Ventilation requirement

1. Vertical wall mount condition

<Side view>

A : min. 40 mm

B: Ambient temperature Measuring point < 35°C

• When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower.

Note

A Samsung Electronics service center can provide details.

Introduction

2. Embedded Mount guide

<Side view> <Top view>

A : min. 40 mm

B : min. 70 mm

C : min. 50 mm

D : min. 50 mm

E : Ambient temperature Measuring point < 35°C

• When embedding the product in a wall, be sure there is some space behind the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower.

Note

A Samsung Electronics service center can provide details.

3. Floor mount guide

<Side view>

A: min. 50 mm

B: Ambient temperature Measuring point < 20°C

• When embedding the product in the floor, be sure there is a 50 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 20 °C or lower.

Note

A Samsung Electronics service center can provide details.

Mechanical Layout

Introduction

* Unit: mm

Installation VESA Bracket

• When installing VESA, make sure to comply with the international VESA standards.

• Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG

Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.

• At least 2 persons are needed in order to move the PDP Display.

• SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.

Dimensions

* Unit: mm

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Accessories (sold separately)

• Dimension with other accessories

Introduction

* Unit: mm

Wall Bracket Installation

• Contact a technician for installing the wall bracket.

• SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

• This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1) Hinge(Left 1, Right

1)

Plastic

Hanger

(4)

Screw

(A)(11)

Screw(B)

(4)

Anchor

(11)

Introduction

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1.

Remove the 4 screws on the back of the product.

2.

Insert the screw B into the plastic hanger.

Notice

• Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.

• Be careful when installing the product on the bracket as fingers can be caught in the holes.

• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

3.

Tighten the 4 screws in step 2 (plastic hanger + screw B) to the rear holes of the product.

4.

Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1).

Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

Introduction

A -

B -

C -

PDP Display

Wall Bracket

Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1.

Fix the product to the wall bracket.

2.

Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Make sure to use the top center, and not the left or the right side of the product to adjust the angle.

Introduction

Remote Control (RS232C)

Cable connections

interface pin

Bits rate

Data Bits

Parity

Stop Bits

Flow control

Maximum length

RS232C(9 pin)

TxD(No.2) RxD(No.3) GND(No.5)

9600 bps

8 bit

None

1 bit

None

15 m (only shielded type)

• Pin assignment

6

7

8

9

2

3

4

5

Pin

1

• RS232C cable

Connector : 9-pin D-Sub

Cable : Cross (reversed) cable

Signal

Data Carrier Detect

Received Data

Transmitted Data

Data Terminal Ready

Signal Ground

Data Set Ready

Request to Send

Clear to Send

Ring Indicator

-P1-

FEMALE Rx

-P1-

2 --------->

-P2-

3 Rx

-P2-

FEMALE

Tx

Gnd

• Connecting method

3

5

Introduction

<---------

----------

2

5

Tx

Gnd

Control codes

• Get control

Header

0xAA

• Set control command command type

Header command

0xAA command type

• commanding words

ID

ID

DATA

Length

1

DATA Length

0

DATA

Value

CheckSum

CheckSum

7

8

9

3

4

5

6

No.

1

2 command type

Power control

Volume control

Input source control

Screen Mode control

Screen Size control

PIP on/off control

Auto adjustment control

Video wall Mode control

Safety Lock command

0x11

0x12

0x14

0x18

0x19

0x3C

0x3D

0x5C

0x5D

- ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF.

Value range

0~1

0~100

-

-

0~255

0~1

0

0~1

0~1

Introduction

- Every communication will be made in hexadecimals and Checksum is the sum of all remainings.

If it exceeds two digits,for example, it is 11+FF+01+01=112, discard the number in the first digit like below.

example)PowerOn&ID=0

Header

0xAA command

0x11

ID

DATA

Length

1

DATA 1

Power

CheckSum

Header

0xAA command

0x11

ID

DATA

Length

1

DATA 1

1

12

If you want to control every mechanism connected with Serial Cable regardless of its ID, set ID part to "0xFE" and send commands. At the time, each product will follow commands but it will not respond with ACK.

• Power Control

• Function

Personal Computer turns TV / Monitor power ON/OFF.

• Get Power ON/OFF Status

Header

0xAA command

0x11

ID

DATA Length

0

CheckSum

• Set Power ON/OFF

Header command

ID

0xAA 0x11

Power : Power code to be set on TV / Monitor

1 : Power ON

0 : Power OFF

DATA

Length

1

• Ack

Header command

0xAA 0xFF

Power : Same as above

ID

DATA

Length

3

Ack/Nak

‘A’

DATA

Power r-CMD

0x11

Val1

Power

CheckSum

Check

Sum

• Nak

Header command ID

DATA

Length

Ack/Nak r-CMD Val1

Check

Sum

Introduction

0xAA 0xFF 3 ‘N’

ERR : Error code that shows what occurred error is

• Volume Control

• Function

Personal Computer changes volume of TV / Monitor.

• Get Volume Status

Header

0xAA command

0x12

ID

0x11

DATA Length

0

ERR

CheckSum

• Set Volume

Header

0xAA command

0x12

ID

DATA

Length

1

DATA

Volume

Volume : Volume value code to be set on TV / Monitor (0 ~ 100)

• Ack

Header command

0xAA 0xFF

Volume : Same as above

ID

DATA

Length

3

Ack/Nak

‘A’ r-CMD

0x12

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x12

Val1

Volume

Val1

ERR

CheckSum

Check

Sum

Check

Sum

• Input Source Control

• Function

Personal Computer changes input source of TV / Monitor.

• Get Input Source Status

Header

0xAA command

0x14

ID

DATA Length

0

CheckSum

Introduction

• Set Input Source

Header

0xAA command

0x14

ID

DATA

Length

1

Input Source : Input Source code to be set on TV / Monitor

DATA

Input Source

CheckSum

0x08

0x20

0x1F

0x30

0x40

0x21

0x22

0x23

0x24

0x25

0x14

0x1E

0x18

0x0C

0x04

PC

BNC

DVI

AV

S-Video

Component

MagicInfo

DVI_VIDEO

RF(TV)

DTV

HDMI1

HDMI1_PC

HDMI2

HDMI2_PC

DisplayPort

Caution

DVI_VIDEO, HDMI1_PC, HDMI2_PC → Get Only

In the case of MagicInfo, only possible with models include MagicInfo

In the case of TV, only possible with models include TV.

• Ack

Header command

0xAA 0xFF

ID

Input Source : Same as above

DATA

Length

3

Ack/Nak

‘A’ r-CMD

0x14

Val1

Input

Source

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x14

Val1

ERR

Check

Sum

Check

Sum

Introduction

• Screen Mode Control

• Function

Personal Computer changes "Screen Mode" of TV / Monitor

Cannot be controlled when Video Wall is on.

Caution

Only works with models include TV.

• Get Screen Mode Status

Header

0xAA command

0x18

ID

DATA Length

0

CheckSum

• Set Picture Size

Header

0xAA command

0x18

ID

DATA

Length

1

Screen Mode : Screen Mode code to be set on TV / Monitor

DATA

Screen Mode

CheckSum

0x01

0x04

0x31

0x0B

16 : 9

Zoom

Wide Zoom

4 : 3

• Ack

Header command

0xAA 0xFF

ID

Screen Mode : Same as above

DATA

Length

3

Ack/Nak

‘A’ r-CMD

0x18

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x18

Val1

Screen

Mode

Val1

ERR

Check

Sum

Check

Sum

• Screen Size Control

• Function

Personal Computer recognizes the screen size of TV / Monitor.

Introduction

• Get Screen Size Status

Header

0xAA command

0x19

ID

DATA Length

0

CheckSum

• Ack

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘A’ r-CMD

0x19

Val1

Screen

Size

Screen Size : Screen Size of TV / Monitor (Range : 0 ~ 255, Unit : Inch)

Check

Sum

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x19

Val1

ERR

Check

Sum

• PIP ON / OFF Control

• Function

The PC turns the PIP function of a TV or Monitor ON / OFF.

This does not operate in MagicInfo mode.

• Get the PIP ON / OFF Status

Header

0xAA command

0x3C

ID

DATA Length

0

CheckSum

• Set the PIP ON / OFF

Header

0xAA command

0x3C

ID

DATA

Length

1

PIP : The PIP ON / OFF code to set for the TV or Monitor

1 : PIP ON

0 : PIP OFF

• Ack

Header command

0xAA 0xFF

ID

DATA

Length

3

Ack/Nak

‘A’ r-CMD

0x3C

DATA

PIP

Val1

PIP

CheckSum

Check

Sum

Introduction

PIP : Same as above

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x3C

• Auto Adjustment Control (PC, BNC Only)

• Function

Personal Computer controls PC system screen automatically.

Val1

ERR

Check

Sum

• Get Auto Adjustment Status

None

• Set Auto Adjustment

Header

0xAA command

0x3D

ID

DATA

Length

1

DATA

Auto Adjustment

CheckSum

Auto Adjustment : 0x00 (Always)

• Ack

Header command

0xAA 0xFF

ID

DATA

Length

3

Ack/Nak r-CMD

‘A’ 0x3D

Val1

Auto Adjustment

Check

Sum

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x3D

Val1

ERR

Check

Sum

• Video Wall Mode Control

• Function

Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON.

Only works with TV / Monitor where Video Wall is on.

Introduction

Does not operate in MagicInfo

• Get Video Wall Mode

Header

0xAA command

0x5C

ID

DATA Length

0

CheckSum

• Set Video Wall Mode

Header

0xAA command

0x5C

ID

DATA

Length

1

DATA

Video Wall

Mode

Video Wall Mode : Video Wall Mode code to be set on TV / Monitor

1 : Full

0 : Natural

CheckSum

• Ack

Header

0xAA command

0xFF

ID

Video Wall Mode : same as above

DATA

Length

Ack/Nak r-CMD

3 ‘A’ 0x5C

Val1

Video

Wall

Mode

Check

Sum

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x5C

Val1

ERR

Check

Sum

• Safety Lock

• Function

Personal Computer turns Safety Lock function of TV / Monitor ON / OFF.

Can operate regardless of whether power is ON / OFF.

• Get Safety Lock Status

Header

0xAA command

0x5D

ID

DATA Length

0

CheckSum

Introduction

• Set Safety Lock Enable / Disable

Header

0xAA command

0x5D

ID

Safety Lock : Lock code to be set on TV / Monitor

1 : ON

0 : OFF

DATA

Length

1

• Ack

Header command

0xAA 0xFF

ID

Safety Lock : Same as above

DATA

Length

3

Ack/Nak

‘A’

DATA

Safety Lock r-CMD

0x5D

• Nak

Header

0xAA command

0xFF

ID

DATA

Length

3

Ack/Nak

‘N’

ERR : Error code that shows what occurred error is r-CMD

0x5D

Val1

Safety

Lock

Val1

ERR

CheckSum

Check

Sum

Check

Sum

Connections

Connecting a Computer

There are several ways to connect the computer to the monitor. Choose one from the following options.

Using the D-sub (Analog) connector on the video card.

• Connect the D-sub to the 15-pin, [RGB IN] port on the back of your PDP

Display and the 15 pin D-sub Port on the computer.

Using the DVI (Digital) connector on the video card.

• Connect the DVI Cable to the [DVI IN] port on the back of your PDP Display and the DVI port on the computer.

Connections

Using the HDMI (digital) output on the graphics card.

• Connect the [HDMI IN] port on the PDP Display to the HDMI port on the PC using the HDMI cable.

Note

When the HDMI cable to the PC, ensure that you select HDMI from both the

Source List and Edit Name before selecting PC or DVI device so that normal

PC screen and sound can be outputted.

Using the BNC (Analog) connector on the video card.

• Connect the [BNC/COMPONENT IN] port on the monitor to the BNC port on the PC using the BNC to BNC cable.

Connections

Connect the audio cable for your PDP Display to the audio port on the back of the

PDP Display.

Connect the power cord for your PDP Display to the power port on the back of the PDP Display. .

Note

• Turn on both your computer and the PDP Display.

• Contact a local SAMSUNG Electronics Service Center to buy optional items.

Using Whiteboard (P64FT Model Only)

Note

• Whiteboard does not support MagicInfo mode.

• A stylus pen may be subject to electromagnetic interference.

• This wireless device is subject to electromagnetic interference. Do not use this device for a purpose that may affect personal safety.

1. Connecting to a PC

To use Whiteboard, the product should first be connected to a PC.

Refer to "Connecting a Computer" for details about how to connect the product to a PC.

2. Components and Their Functions

2-1. Stylus pen

Connections

2

3

4

No.

1

5

Parts

Pen tip

IR sensor

SW1

SW2

SW3

6 SW4

2-2. Pen Battery Charger

Functions

Enables the stylus pen when the sensor on it is pressed.

Receives IR signals from the panel.

Performs the right-click command.

Functions as the Page Down key on the keyboard. Another function can be assigned as required.

Functions as the Page Up key on the keyboard. Another function can be assigned as required.

power switch

2

3

No.

1

Parts

Power in

Functions

Connects to the power cable via the adapter.

LED Shows the charging status.

Stylus pen holders Charge the batteries on the stylus pens mounted in correct orientation.

Connections

2-3 . Charging a Stylus Pen Battery

Note

• Apply a ferrite core when you charge a pen battery in the charger.

• It is recommended that you use a ferrite core when charging a stylus pen battery to avoid electromagnetic interference.

• Before you connect the cable, open the ferrite core and wrap the cable around the ferrite core as shown below.

• Red LED: Charging / Orange LED: Error / Green LED: Fully charged

Note

• If the LED remains green when you charge a pen battery (indicating fully charged) but the pen cannot power on, contact Samsung Customer Service Center.

• Charging a pen battery may fail unless the pen is mounted in correct orientation on the holder.

Connecting to a Stylus Pen

3-1. Attaching the Dongle

To use a dedicated stylus pen for Whiteboard, insert the dongle into the USB slot on your PC.

Note

• Ensure the dongle is installed 1m or higher from the ground.

3-2. Using a Stylus Pen

To use a stylus pen, press the black button at the upper part of the pen.

Connections

3-3. Pairing Stylus Pens with the Monitor

To connect dual pens to the monitor, install the drawing program in the provided CD on the PC. Refer to "Installing Whiteboard" for details about how to install the drawing program.

• Go to Control Panel and run Samsung Interactive Whiteboard.

(Alternatively, click the star icon[ ] -> Pen Setting in the bottom left corner of the drawing program.)

• Press and hold the (black) power button on the stylus pen for 10 seconds when the power button is turned off.

• Powering on the pen: Press the black power button once. The red LED will blink several times and the pen will power on.

• Powering off the pen: Press and hold the black power button for 3 seconds. The red LED will blink several times and the pen will power off.

• Press Pairing in the Samsung Interactive Whiteboard program. If No Pairing changes to

Conneted, a pairing has been successfully performed and taps of the pen on the screen will immediately be recognized.

• Pairing is required only once. After a pen is paired with the monitor, powering on the pen will enable taps of the pen on the screen to be recognized.

3-4. Activating Calibration

• Go to Control Panel and run Samsung Interactive Whiteboard.

(Alternatively, click the star icon[ ] -> Pen Setting in the bottom left corner of the drawing program.)

• Go to the Calibration tab.

• Click Start Calibration.

• Tap the four circles in sequence using the pen, following the instructions displayed.

Connections

• Click OK.

3-5. Adding Keyboard Commands to Pens

Make better use of Whiteboard by adding keyboard commands to pens.

1.

Go to Pen Setting > Keyboard in the Samsung Interactive Whiteboard program.

2.

Select a button. When the key assignment window appears, press the keyboard key you want to assign. The key will be assigned to the button.

3-6. Right-click Function

Press Button 1 on the pen when the pen contacts the PDP screen. The right-click function of a mouse will be performed.

Connections

Note

• The right-click function does not work unless the pen contacts the PDP screen.

4. Afterimage Burn-in Prevention

Note

• Afterimages can occur on this product due to the nature of PDP devices and the manufacturer shall not be liable for this issue.

• To prevent afterimages, it is recommended that you observe the following instructions when using the product.

Instructions

Ensure the same still image is not displayed for long hours.

• When you need to display the same still image for long hours, be sure to activate Screen saver at regular intervals.

• It is best to activate Screen saver when the Samsung Interactive Whiteboard is not in use.

• Using screen saver

Activating screen saver (when the Interactive Whiteboard software is not in use)

• Go to MENU -> Setup-> Safety Screen in the onscreen display menu and select Pat-

tern mode. A screen saver pattern will activate.

Activating screen saver (when the Interactive Whiteboard software is in use)

Click [ ] and select Eliminate Image Retention in the Interactive Samsung Interactive

Whiteboard. A screen saver pattern will be activated.

Connections

It is recommended that you activate screen saver for a short period of time before you power off the PC.

• Activation of Screen saver after the interactive whiteboard program is closed

• If the PC is turned off: Screen saver will be active for a specified time before the PC powers of

• If the PC is not turned off: The interactive whiteboard program will be closed only.

Connecting to Other devices

• AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your PDP Display.

• The PDP Display's configuration at the back may vary slightly depending on the PDP Display model.

Connecting AV Devices

Connections

1.

Connect an audio cable to the audio output port on the external device and [AV/COMPONENT

AUDIO IN[R-AUDIO-L]] port on the monitor, and connect the video output port on the external device to the [AV IN [VIDEO]] port on the monitor.

2.

Play the DVD, VCR or Camcorder with a DVD disc or tape inserted.

3.

Select AV using the SOURCE button on the front of the PDP display or on the remote.

Connecting to a Camcorder

1.

Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the PDP Display .

2.

Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN

[VIDEO]] on the PDP Display .

3.

Select AV for the Camcorder connection using the SOURCE button on the front of the PDP

Display or on the remote control.

4.

Then, start the Camcorder with a tape inserted.

Note

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.)

If your camcorder is stereo, you need to connect a set of two cables.

Connecting the BNC to BNC cable

Connections

1.

Connect the [BNC/COMPONENT IN [R/P

R

, G/Y, B/P

B

]] ports on the monitor to the BNC port on the external device using the BNC to BNC cable.

2.

Select BNC using the SOURCE button on the front of the PDP Display or on the remote control.

Connecting Using a DVI Cable

1.

Connect between the [DVI OUT] port on the PDP Display and the input port on another monitor using a DVI cable.

2.

Connect between the [AUDIO OUT] port on the PDP Display and the audio input port on another monitor using a stereo cable.

3.

Select DVI using the SOURCE button on the front of the PDP Display or on the remote control.

Note

[DVI OUT] does not support HDCP.

Connecting Using a HDMI Cable

Connections

1.

Connect input devices such as a Blu-Ray/DVD player to the [HDMI IN] terminal of the PDP

Display using an HDMI cable.

2.

Select HDMI using the SOURCE button on the front of the PDP Display or on the remote control.

Note

In HDMI mode, only PCM format audio is supported.

When the HDMI cable to the PC, ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted.

Connecting Using a DVI to HDMI Cable

1.

Connect the DVI output terminal of a digital output device to the [HDMI IN] terminal of the PDP

Display using a DVI to HDMI cable.

Connections

2.

Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [DVI / RGB

AUDIO IN] terminal of the PDP Display.

3.

Select HDMI using the SOURCE button on the front of the PDP Display or on the remote control.

Connecting a DVD Player

1.

Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the PDP Display and the AUDIO OUT jacks on the DVD player.

2.

Connect a Component cable between the [BNC/COMPONENT IN [R/P

R the PDP Display and the P

R

, Y, P

B

jacks on the DVD player.

, G/Y, B/P

B

]] port on

Note

• Select Component for the connection to a DVD player using the SOURCE button on the front of the PDP Display or on the remote control.

• Then, start the DVD Player with a DVD disc inserted.

• A component cable is optional.

• For an explanation of Component video, consult your DVD manual.

Connections

Connecting a DTV Set Top (Cable/Satellite) Box

1.

Connect a Component cable between the [BNC/COMPONENT IN [R/P

R the PDP Display and the P

R

, Y, P

B

jacks on the Set Top Box.

, G/Y, B/P

B

]] port on

2.

Connect a set of audio cables between the [AV COMPONENT AUDIO IN [R-AUDIO-L]] on the PDP Display and the AUDIO OUT jacks on the Set Top Box.

Note

• Select Component for the connection to a DTV Set Top Box using the SOURCE button on the front of the PDP Display or on the remote control.

• For an explanation of Component video, see your Set Top Box owner's manual.

Connecting to an Audio System

1.

Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO

OUT] on PDP Display.

Using the Software

Installing Whiteboard (P64FT Model Only)

1.

First, insert the Whiteboard installation CD into the CD-ROM drive.

2.

Double-click Whiteboard.exe.

3.

Click "Next" in the displayed installation wizard screen.

4.

When the "License Agreement" window appears, select "I accept the terms of the license

agreement" and click "Next."

5.

Select "PC Mode" and click "Next" in the displayed "Setup Type" window.

6.

Select "PDP Monitor" and click "Next."

7.

Click "Install" in the displayed "Ready to Install the Program" window.

8.

A window showing the installation progress will appear.

9.

Click "Finish" in the displayed "InstallShield Wizard Complete" window.

10. After the installation, the Samsung Interactive Whiteboard shortcut icon will be created on the desktop.

MDC (Multiple Display Control)

Installation

1.

Insert the installation CD into the CD-ROM drive.

2.

Click the Serial MDC installation program.

Note

If the screen for installing the software does not appear, install it using the Serial MDC execution file in the MDC folder of the CD-ROM.

3.

If the installation wizard screen does appear, click "Next."

4.

The "License Agreement" screen will appear. Click "Yes."

5.

The "Customer Information" window will appear. Register the user information and click "Yes."

6.

The "Choose Destination Location" window will appear. Specify the file location to install to and click "Next."

Note

If the file location is not specified, the program will be installed in the default file location.

7.

The "Start Copying Files" window will appear. Confirm the file location and click "Next."

8.

The installation progress screen will appear.

Using the Software

9.

The "InstallShield Wizard Complete" screen will appear. Click "Finish."

Note

Select " Launch Serial MDC" and click "Finish." The MDC program will immediately be run.

10. If the installation is successfully completed, the quick Serial MDC execution icon will appear on the desktop.

MDC execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.

Installation Problems

Uninstall

The installation of MDC can be affected by such factors as the video card, motherboard and the network environment.

The MDC program can be removed only by using the "Add or Remove Programs" option of the

Windows ® Control Panel.

Perform the following steps remove MDC.

Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program".

Select Serial MDC from the list and then click the "Add/Delete" button.

Using Serial MDC

Introduction

A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display.

Main Screen

Click Start > Program > Samsung > MDC System to start the program.

Select a set to see the volume of the selected set within the slider.

Main Icons

Remote control

Safety Lock

Port Selection

Lamp Control

Option...

Dropdown Selectors

All

Selection Buttons

Refresh

Display Selection

Info Grid

Control Tools

OSD Display

1.

Use the main icons to switch into each screen.

2.

Allows you to enable or disable the remote control signal receiving function of the display unit.

3.

Set the Safety Lock function.

When setting the Lock function, you can only operate power and lock buttons on the remote control and set.

4.

The setting for the PC Serial Port can change. The original value is COM1.

5.

Selects a Lamp adjustment mode.

6.

Adjusts the number of LFD IDs and the frequency of search repeats.

7.

Defines the range of LFD IDs to display. You can select or deselect the displayed IDs using the Select or Clear button.

8.

All of the monitors can be selected or deselected.

9.

Selects (Select) or deselects (Clear) LFD IDs displayed by configuring 7 and 8.

10. This searches for monitors. The maximum number is indicated in the Max LFD Id field.

11. Select a display from Display Selection.

12. Use Grid to view brief information on selected display.

13. Use Control Tools to control displays.

14. Switches the OSD function On/Off.

- May not be supported depending on the product.

<Note> The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is shut down, the remote control signal receiving function of all displays is initialized to Enable when the

MDC is closed.

Port Selection

1. The Multiple Display Control is originally set to COM1.

2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu.

3. If the exact port name that is connected to the PDP Display using a serial cable is not selected, communication will be unavailable.

4. The selected port is stored in the program and used for the next program as well.

Power Control

1. Click Power Control of the main icons and the Power Control screen appears.

Info Grid shows some basic information necessary to Power Control.

1) (Power Status)

2) Input

3) Image Size

4) On Timer

5) Off Timer

2. Selects displays you want to adjust using the Select button or checkboxes.

Power Control allows controlling some of the functions of the selected display.

1) Power On/Off

- Turns the power of the selected display On/Off.

2) Volume

- Controls the volume level of the selected display.

It receives the volume value of the selected display from the sets and displays it in the slider.

(If you deselect a single display or all displays, the default value 10 will be restored.)

3) (Mute On/Off)

- Turns on/off the Mute function of the selected display.

When selecting one set at a time, turn on the Mute function for the selected set.

The Mute function is disabled automatically when you adjust the volume level.

(The values return to the default settings when you undo the selections or choose "Select All".)

The Power Control feature is available for all displays.

The Volume Control and Mute features are available only for the displays whose power status is ON.

3. Selects whether to display the menu screen using the OSD Display menu.

1) Source OSD

- Sets whether the Source OSD will be displayed to indicate when the Source is changed.

2) Not Optimum Mode OSD

- Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported.

3) No Signal OSD

- Sets whether the No Signal OSD will be displayed to indicate when there is no signal.

4) MDC OSD

- Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.

Input Source

1. Click Input Source of the main icons and the Input Source control screen appears.

Selects displays you want to adjust using the Select button or checkboxes.

• TV Mode

• PC Mode

1)

Info Grid shows some basic information necessary to Input Source Control.

PC

2)

3)

4)

5)

6)

7)

8)

9)

- Changes the Input Source of the selected display to PC.

BNC

- Changes the Input Source of the selected display to BNC.

DVI

- Changes the Input Source of the selected display to DVI.

TV

- Changes the Input Source of the selected display to TV.

DTV

- Changes the Input Source of the selected display to DTV.

AV

- Changes the Input Source of the selected display to AV.

S-Video

- Changes the Input Source of the selected display to S-Video.

Component

- Changes the Input Source of the selected display to Component.

MagicInfo

- The Input source of MagicInfo works only on MagicInfo model.

10) HDMI1/HDMI2

- Changes the Input Source of the selected display to HDMI.

11) DP

- Switches the input source for the selected Display to DP.

12) Channel

- Channel arrow appears when the Input Source is TV.

HDMI2 may not be supported depending on the product.

DP may not be supported depending on the product.

TV Source can be selected only in products with TV and controlling channels is allowed only when

Input Source is TV.

The Input Source Control feature is available only for the displays whose power status is ON.

Image Size

PC, BNC, DVI, DP

1. Click Image Size of the main icons and the Image Size control screen appears.

1)

Info Grid shows some basic information necessary to Image Size Control.

( Power Status)

- Shows the power status of the current display.

2) Image Size

- Shows the current Image Size of the display in use.

3) Input

- Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP.

4) PC Source

- Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs.

- The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.

5) Video Source

- Using the Image Size adjustment button, you can adjust the Image Size to a value available in the PC, BNC, DVI and DP.

DP may not be supported depending on the product.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Image Size Control is available only for the displays for which power status is ON.

Image Size

TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV.

1. Click Image Size of the main icons and the Image Size control screen appears.

Info Grid shows some basic information necessary to Image Size Control.

1) To adjust Image Size in TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV mode, click the Video Source tab.

Select the display you want to adjust by using the Select button or by checking the checkbox.

2) Info Grid displays only the display having TV, AV, S-Video, Component, HDMI1, HDMI2 or DTV as input source.

3) Switch Image Size of the selected display randomly.

4) The screen modes can only be adjusted when a TV (PAL only) is connected and the Image Size item is set to Auto

Wide.

HDMI2 may not be supported depending on the product.

Custom may not be supported depending on the product.

Auto Wide, Zoom1 and Zoom2 are not available for selection when the input signal type for Component and DVI (HDCP) is 720p or 1080i.

(The Auto Wide mode is available only for TV, AV, and S-Video.)

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

The Image Size Control feature is available only for the displays whose power status is ON.

Time

1. Click Time of the main icons and the Time Control screen appears.

Info Grid shows some basic information necessary to Time Control.

1) Set clock

- Set the current time for the selected display (PC Time).

- To change the current time, first change the PC Time.

2) Timer

- Sets up Timer1, Timer2, Timer3 and Holiday Management.

3) Shows whether Timer is activated.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Time Control is available only for the displays for which the power status is ON.

Time

Setting up Timer and Holiday Management

1. 1. Setting up Timer1, Timer2 and Timer3

1) On Time

- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on.

2) Off Time

- Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off.

3) Volume

- Selects the volume when the selected monitor is turned on.

4) Source

- Selects the external input source that will be displayed when the selected monitor is turned on.

5) Holiday

- Applies the Holiday Management function to the Timer.

6) Repeat

- Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual.

z z z z z z

Once : The Timer goes off only once.

EveryDay : EveryDay: The Timer repeats daily.

Mon~Fri : The Timer repeats from Monday through Friday.

Mon~Sat : The Timer repeats from Monday through Saturday.

Sat~Sun : Sat~Sun: The Timer goes off on Saturday and Sunday.

Manual : Select a day of the week you want the Timer to go off.

2. Setting Holiday Management

The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer.

1) Specifies the date.

2) Delete All

- Deletes all of the holidays.

3) Add

- Adds the specified date.

4)

- Deletes the schedule in the selected line.

The Holiday Management function can be turned on or off in the Timer setup menu.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Time Control is available only for the displays for which the power status is ON.

Only enabled for a TV when Source is set to TV in On Time mode.

Only enabled for a model with MagicInfo installed when Source is set to MagicInfo in On Time mode.

PIP

PIP Size

1. Click PIP of the main icons and the PIP control screen appears.

Selects displays you want to adjust using the Select button or checkboxes.

Info Grid shows some basic information necessary to PIP Size Control.

1) PIP Size

- Shows the current PIP Size of the display in use.

2) OFF

- Turns off the PIP of the selected display.

3) Large

- Turns on the PIP of the selected display and changes the size to Large.

4) Small

- Turns on the PIP of the selected display and changes the size to Small.

5) Double 1

- Turns on the PIP of the selected display and changes the size to Double 1.

6) Double 2

- Turns on the PIP of the selected display and changes the size to Double 2.

7) Double 3 (Picture By Picture)

- Turns on the PBP of the selected display and changes the size to Double 3.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

PIP Size can be controlled with turning on the PDP Display power.

PIP

PIP Source

1. Click PIP of the main icons and the PIP control screen appears.

Info Grid shows some basic information necessary to PIP Source Control.

1) PIP Source

- PIP Source can be controlled with turning on the PDP Display power.

2) PC

- Changes the source of the PIP of the selected display to PC.

3) BNC

- Changes the source of the PIP of the selected display to BNC.

4) DVI

- Changes the source of the PIP of the selected display to DVI.

5) TV

- Changes the source of the PIP of the selected display to TV.

6) DTV

- Changes the source of the PIP of the selected display to DTV.

7) AV

- Changes the source of the PIP of the selected display to AV.

8) S-Video

- Changes the source of the PIP of the selected display to S-Video.

9) Component

- Changes the source of the PIP of the selected display to Component.

10) HDMI1/HDMI2

- Changes the source of the PIP of the selected display to HDMI.

11) DP

- Switches the PIP Source of the selected Display to DP.

HDMI2 may not be supported depending on the product.

DP may not be supported depending on the product.

Some of the PIP Sources may not be available for selection, depending on the input source type of the

Main Screen.

The Input source of MagicInfo works only on MagicInfo model.

The PIP Control feature is available only for the displays whose power status is ON and the PIP function is set to ON.

Settings

Picture

1. Click Settings of the main icons and the Settings Control screen appears.

Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.

1) Picture

- Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV.

2) Contrast

- Adjusts Contrast of the selected display.

3) Brightness

- Adjusts Brightness of the selected display.

4) Sharpness

- Adjusts Sharpness of the selected display.

5) Color

- Adjusts Color of the selected display.

6) Tint

- Adjusts Tint of the selected display.

- Available only for NT.

7) Color Tone

- Adjusts the Color Tone for the selected display.

8) Color Temp

- Adjusts the Color Temp for the selected display.

9) Brightness Sensor

- Adjusts the Brightness Sensor for the selected display.

10) Dynamic Contrast

- Adjusts the Dynamic Contrast for the selected display.

HDMI2 may not be supported depending on the product.

Brightness Sensor may not be supported depending on the product.

The Input source of MagicInfo works only on MagicInfo model.

Color Temp is only enabled if the Color Tone is set to Off.

The Input source of TV works only on TV model.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Picture PC

1. Click Settings of the main icons and the Settings Control screen appears.

Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.

1) Picture PC

- Available only for PC, BNC, DVI and DP.

2) Contrast

- Adjusts Contrast of the selected display.

3) Brightness

- Adjusts Brightness for the selected display.

4) Red

- Adjusts red Color of the selected display.

- Available only for NT.

5) Green

- Adjusts green Color of the selected display.

- Available only for NT.

6) Blue

- Adjusts blue Color of the selected display.

- Available only for NT.

7) Color Tone

- Adjusts the Color Tone for the selected display.

8) Color Temp

- Adjusts the Color Temp for the selected display.

9) Brightness Sensor

- Adjusts the Brightness Sensor for the selected display.

10) Dynamic Contrast

- Adjusts the Dynamic Contrast for the selected display.

DP may not be supported depending on the product.

Brightness Sensor may not be supported depending on the product.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Color Temp is only enabled if the Color Tone is set to Off.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Audio

1. Click Settings of the main icons and the Settings Control screen appears.

Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.

1) Audio

- Controls audio settings for all input sources.

2) Bass

- Adjusts Bass of the selected display.

3) Treble

- Adjusts Treble of the selected display.

4) Balance

- Adjusts Balance of the selected display.

5) SRS TS XT

- SRS TS XT Sound ON/OFF of the selected display.

6) Sound Select

- Select either Main or Sub when PIP is On.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.

Settings

Image Lock

1. Click Settings of the main icons and the Settings Control screen appears.

Info Grid shows some basic information necessary to Settings Control.

1) Image Lock

- Available only for PC, BNC.

2) Coarse

- Adjusts Coarse of the selected display.

3) Fine

- Adjusts Fine of the selected display.

4) Position

- Adjusts Position of the selected display.

5) Auto Adjustment

- Self-Adjust to the incoming PC signal.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Settings Control is available only for the displays for which the power status is ON.

Maintenance

Lamp Control

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

An "Info Grid" showing several basic data items appears.

1) Maintenance

- Allows the Maintenance Control function for all input sources.

2) Lamp Control

- Automatically adjusts the backlight of the selected display at a specified time.

The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control.

- Allows you to adjust the backlight of the selected display regardless of the time.

The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.

3) Ambient Light

- Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness.

- You can specify a Reference value and designate a monitor that will automatically determine Lamp Value (the light intensity from the lamp), based on the ambient light intensity.

Ambient Light is only supported for models that have a brightness sensor and is only enabled when

Ambient Brightness Mode is selected in the Lamp Control menu.

Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in the Lamp Control menu.

The Maintenance Control feature is available only for the displays whose power status is ON.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

Maintenance

Scroll

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

1) Scroll

- This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time.

2) Pixel Shift

- This allows the screen to be moved finely at the specified time interval.

3) Safety Screen

- The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time. The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed.

The Type item can be set to Scroll, Pixel, Bar, Eraser, All White, or Pattern.

4) Safety Screen2

- This function is used to prevent afterimages from occurring. There are five (5) types that you can select and control with this function.

For the Scroll type, the Time item can be set to 1, 2, 3, 4 or 5. For the Bar and Eraser types, it can be set

to 10, 20, 30, 40 or 50. For the All White and Pattern type, it can be set to 1, 5, 10, 20 or 30.

The Input source of MagicInfo works only on MagicInfo model.

The Input source of TV works only on TV model.

The Maintenance Control feature is available only for the displays whose power status is ON.

Maintenance

Video Wall

1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.

1) Video Wall

- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen.

2) Video Wall Control

- Video Wall properties can be configured.

1) On / Off

- Turns on/off the Video Wall function of the selected display.

2) Format

- The format can be selected to see a divided screen. z

Full z

Natural

3) Video Wall (Screen divider)

- The screen can be divided into.

You can select a number of screens with a different layout when dividing. z z

Select a mode from Screen divider.

Select a display from Display Selection. z z

The place will be set up by pressing a number in the selected mode.

The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 z

Up to 15 monitors can be arranged in a row. The maximum value for Horizontal is 6 if Vertical is set to 15 while the maximum value for Vertical is 6 if Horizontal is set to 15.

4) Viewing Screen Splits

- You can view and change the layout of screens using the Screen Divider settings.

The range of the Screen Divider setting may differ depending on the model.

You may not operate this function in MagicInfo.

The Input source of TV works only on TV model.

The Maintenance Control function is available only for the displays where the power status is ON.

Troubleshooting

1. The display you wish to control does not appear on the Power Control Info Grid

- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)

- Check the displays to see if any of the other displays connected have the same ID. If more than one displays have the same ID, those displays are not properly detected by the program due to data conflict.

- For monitors that support a Set ID between 0 to 99, you have to set the Set ID to a value between 0 and 99.

Note : Check if the Set ID of the monitor is a value between 0 and 99 (set the value using the Display menu).

2. The display you wish to control does not appear on the other Control Info Grids

- Check to see if the display power is ON. (You can check this in Power Control Info Grid)

- Check if you can change the input source of the display.

3. The dialogue box appears repeatedly.

- Check to see if the display you wish to control is selected.

4. Both On Timer and Off Timer have been set but different time is showing.

- Apply current time to synchronize the display clocks.

5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C cable, or exit the program in an Irregular manner. Rerun the program and turn the remote function again to Restore normal functions.

<Note> This program may malfunction due to problems in communication circuits or interference from electronic appliances nearby.

Settings Value Display In Multiple Display Mode

When there are more than one displays connected, the settings values are displayed as follows.

1. No selection: Displays the Factory Default Value.

2. Selected one display: Fetches and displays the settings value for the selected display.

3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of

ID 1, fetches and displays the value of ID3.

4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.

Adjusting the PDP Display

Input

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Source List

Use to select PC, DVI or other external input sources connected to the PDP Display. Use to select the screen of your choice.

1.

PC

2.

DVI

3.

AV

4.

HDMI

5.

MagicInfo - Enabled when a network box is connected.

6.

Component

7.

BNC

Note

• The direct button on the remote control is the 'SOURCE' button.

Edit Name

Adjusting the PDP Display

Name the input device connected to the input jacks to make your input source selection easier.

VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /

Camcorder / DVD Combo / DHR / PC

Note

• Set Edit Name to PC when a PC is connected via the HDMI or DVI port.

In most other cases, set Edit Name to AV.

Note that Edit Name should be set to the connected source device if the source device's signal is

640 x 480, 720p (1280 x 720), or 1080p (1920 x 1080) because these signals are compatible with both AV and PC input.

• The Picture menu changes depending on the input signal and Edit Name.

Picture [PC / DVI / BNC Mode]

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Note

MagicInfo can only be enabled when a network box is connected.

• The HDMI port and network box cannot be connected at the same time.

MagicBright

The MagicBright function is only enabled in PC mode. The function offers a picture that is twice as bright and vivid as conventional monitors so that users' various needs (to prepare documents, use the

Internet, view videos, etc.) are satisfied.

Adjusting the PDP Display

1.

Entertain

High brightness

For watching motion pictures such as a DVD or VCR.

2.

Internet

Medium brightness

For working with a mixture of images such as texts and graphics.

3.

Text

Normal brightness

For documentations or works involving heavy text.

4.

Custom

Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.

If this is the case, adjust the brightness and contrast by using the OSD menu.

Custom

By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

Note

Contrast

By adjusting the picture using the Custom function, MagicBright will change to Custom mode.

Adjusts the Contrast.

Brightness

Adjusts the Brightness.

Sharpness

Adjusts the Sharpness.

Color Tone

Adjusting the PDP Display

The color tones can be changed.

1.

Off

2.

Cool

3.

Normal

4.

Warm

5.

Custom

Color Control

Adjusts individual Red, Green, Blue color balance.

Note

If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.

Red

Note

If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled.

If you set the Color Tone to Off, the Color Control function is disabled.

Green

Blue

Color Temp.

Color Temp. is a measure of the 'warmth' of the image colors.

Note

This function is only enabled if the Color Tone is set to Off.

Image Lock

Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the

Coarse adjustment and then use Fine again.

Note

Available in PC mode only

Adjusting the PDP Display

Coarse

Fine

Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.

Position

Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).

1.

H-Position

Adjusts the screen location horizontally.

2.

V-Position

Adjusts the screen location vertically.

Auto Adjustment

The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed.

Note

Enabled in PC or BNC mode only.

Signal Balance

Note

• Enabled in PC or BNC mode only.

• This is used to make up for the weak RGB signal transmitted by a long signal cable.

Signal Balance

Adjusting the PDP Display

Selects either On or Off with the signal balance.

Signal Control

1.

R-Gain

2.

G-Gain

3.

B-Gain

4.

R-Offset

5.

G-Offset

6.

B-Offset

Size

The Size can be switched.

1.

16:9

2.

4:3

Picture [ AV / HDMI / Component Mode]

Available Modes

PC / DVI / BNC

AV

HDMI

Mode

Component

Adjusting the PDP Display

The PDP Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Cus-

tom") that are preset at the factory.

Dynamic, Standard, Movie, or Custom can be activated.

1.

Dynamic

2.

Standard

3.

Movie

4.

Custom

Custom

By using the on-screen menus, the contrast and brightness can be changed to your personal preference.

Contrast

Adjusts the Contrast.

Brightness

Adjusts the Brightness.

Sharpness

Color

Adjusts the picture Sharpness.

Tint

Adjusts the picture Color.

Adjusting the PDP Display

Adds a natural tone to the display.

Color Tone

The color tones can be changed. The individual Color components are also user adjustable.

1.

Off

2.

Cool2

3.

Cool1

4.

Normal

5.

Warm1

6.

Warm2

Note

If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled.

Color Temp.

Size

Color temp. is a measure of the 'warmth' of the image colors.

Note

This function is only enabled if the Color Tone is set to Off.

The Size can be switched.

1.

16:9 - Sets the picture to 16:9 wide mode.

Adjusting the PDP Display

2.

Zoom 1 - Magnifies the size of the picture on the screen.

3.

Zoom 2 - Magnifies the size of the picture more than “Zoom 1”.

4.

4:3 - Sets the picture to 4:3 normal mode.

5.

Just Scan - Displays the input scenes as they are without any cutoff when HDMI / Compo-

nent 720p, 1080i, 1080p signals are input.

Note

• Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Screen Fit feature.

Zoom1 and Zoom2 are not available in HDMI or Component mode.

• The Position and Reset functions are available in Zoom 1 or Zoom 2 modes.

Digital NR (Digital Noise Reduction)

Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images.

Deactivated in HDMI / AV with a resolution of 1080p.

1.

Off

2.

On

Note

Digital NR function is not available for all resolutions.

Film Mode

The Film Mode feature offers you a theater-quality viewing experience.

Film Mode is supported in AV, Component (480i / 1080i) and HDMI (480i / 1080i).

Adjusting the PDP Display

Sound

Note

• In HDMI mode, this function can be available when the input signal is interlaced scan; it cannot be available with progressive scan signal.

1.

Off

2.

On

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Mode

Custom

The PDP Display has a built-in high fidelity stereo amplifier.

1.

Standard

Selects Standard for the standard factory settings.

2.

Music

Selects Music when watching music videos or concerts.

3.

Movie

Selects Movie when viewing movies.

4.

Speech

Selects Speech when watching a show that is mostly dialogue (i.e., news).

5.

Custom

Selects Custom if you want to adjust the settings according to your personal preferences.

The sound settings can be adjusted to suit your personal preferences.

Adjusting the PDP Display

Bass

Note

• You can hear the sound even when sound value is set to 0.

• If you adjust sound using Custom function, Mode will turn to Custom mode.

Treble

Emphasizes low frequency audio.

Balance

Emphasizes high frequency audio.

Allows you to Adjusts the sound balance between the left and right speakers.

Auto Volume

Reduces the difference in volume control between broadcasters.

1.

Off

2.

On

SRS TS XT

SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.

1.

Off

2.

On

Setup

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Language

Adjusting the PDP Display

You can choose one of 13 languages.

Note

The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.

Time

You can set the time.

Clock Set

Current Time Setting.

Adjusting the PDP Display

Sleep Timer

Turns the PDP Display off automatically at certain times.

1.

Off

2.

30

3.

60

4.

90

5.

120

6.

150

7.

180

Timer1 / Timer2 / Timer3

You can set the PDP display to automatically turn on or off at a specified time.

Note

• Only enabled when the clock is set using the Clock Set menu.

• The Manual option allows you to select a day of the week.

Holiday : When Choose Apply, timer is not available on holiday; when choose Don't apply, timer is available on holiday.

Holiday Management

• Add

You can register holidays.

• Delete Selected

Adjusting the PDP Display

You can delete selected holidays.

Note

• Only enabled when registered holidays are selected.

• More than one holiday can be selected and deleted.

• Delete All

You can delete all the registered holidays.

Menu Transparency

Change the transparency of the background of the OSD.

1.

High

2.

Medium

3.

Low

4.

Opaque

Safety Lock

Change PIN

Adjusting the PDP Display

Lock

The password can be changed.

The preset password for the PDP Display is "0000".

Note

• If you forgot your password, press the remote buttons INFO + EXIT + MUTE to reset the password to "0000."

This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings.

Energy Saving

This feature adjusts the power consumption of the unit in order to save energy.

1.

Off

2.

On

Note

If Energy Saving mode is Off, you can obtain the maximum display brightness.

HDMI Black Level

Adjusting the PDP Display

When a DVD or set-top box is connected to your Product via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the

HDMI Black Level.

1.

Normal

2.

Low

Video Wall

A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen.

When the Video Wall is on, you can adjust the Video Wall screen setting.

Note

When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available.

Video Wall does not operate in MagicInfo mode.

Video Wall

Format

Turns Off/On the Video Wall function of the selected display Off/On.

1.

Off

2.

On

Adjusting the PDP Display

The Format can be selected to see a divided screen.

1.

Full

Provides a full screen without any margins.

2.

Natural

Displays a natural image with the original aspect ratio intact.

Horizontal

Vertical

Sets how many parts the screen should be divided horizontally.

Five adjustment levels: 1, 2, 3, 4, and 5.

Sets how many parts the screen should be divided vertically.

Five adjustment levels: 1, 2, 3, 4, and 5.

Screen Divider

The screen can be divided into several images. A number of screens can be selected with a different layout when dividing.

• Select a mode in Screen Divider.

• Select a display in Display Selection.

Adjusting the PDP Display

• The selection will be set up by pressing a number in the selected mode.

Safety Screen

The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time.

• The Safety Screen function scrolls the screen for the specified period of time.

• This function is not available when the power is turned off.

Pixel Shift

Pixel Shift

To prevent after-images on the screen you can use this function, so that every minute pixels on the

PDP are moved in horizontal or vertical direction.

1.

Off

2.

On

Horizontal Dot

Sets how many pixels the screen moves horizontally.

Five adjustment levels: 0, 1, 2, 3, and 4.

Vertical Line

Sets how many pixels the screen moves vertically.

Time

Adjusting the PDP Display

Five adjustment levels: 0, 1, 2, 3, and 4.

Timer

Timer

Set the time interval for performing the horizontal or vertical movement, respectively.

Mode

You can set the timer for Screen Burn Protection.

If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish.

1.

Off

2.

On

You can change the Safety Screen Type.

1.

Scroll

2.

Bar

3.

Eraser

4.

All White

5.

Pattern

Adjusting the PDP Display

Period

Time

Use this function to set the execution period for each mode set in the timer.

Scroll

Within the set period of time specify a time for execution.

Mode-Scroll : 1~5 sec

Mode-Bar, Eraser : 10~50 sec

Mode-All White, Pattern : 1, 5, 10, 20 30 min

Bar

This function prevents after-images on the screen by moving all the pixels on the PDP according to a pattern.

Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.

Adjusting the PDP Display

Eraser

This function prevents after-images on the screen by moving long black and white vertical lines.

All White

This function prevents after-images on the screen by moving a rectangular pattern.

Pattern

This function prevents after-images on the screen by changing the color of pixels to white.

Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.

This function prevents after-images on the screen by moving a diagonal pattern stored in the panel repeatedly.

Resolution Select

When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @

Adjusting the PDP Display

60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution.

Note

Available in PC mode only

1.

Off

2.

1024 x 768

3.

1280 x 768

4.

1360 x 768

5.

1366 x 768

Note

Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 @ 60Hz, 1280

x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz.

Power On Adjustment

Adjust the Power On time for the screen.

Caution: Set the Power On time to be longer to avoid overvoltage.

Side Gray

Select the brightness of the grey for the screen background.

1.

Off

2.

Light

3.

Dark

Adjusting the PDP Display

Reset

Reverts the product settings to factory defaults. The Reset function is only available when PC / DVI is being used.

Image Reset

Note

Available in PC mode only

The Reset function is not available when Video Wall is On.

Color Reset

OSD Rotation

OSD Rotate

1.

Landscape

2.

Portrait

Multi Control

Available Modes

PC / DVI / BNC

AV

HDMI

Component

Multi Control

Assigns an individual ID to the SET.

Adjusting the PDP Display

• ID Setup

Assigns distinctive IDs to the SET.

• ID Input

Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated.

Troubleshooting

Self-Test Feature Check

Note

Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself.

Self-Test Feature Check

1.

Turn off both your computer and the PDP Display.

2.

Unplug the video cable from the back of the computer.

3.

Turn on the PDP Display.

The figure shown below ("Check Signal Cable") appears on a black background when the PDP

Display is working normally even though no video signal is detected: While in the Self-Test mode, the LED power indicator remains green and the figure moves around on the screen.

4.

Turn off your PDP Display and reconnect the video cable; then turn on both your computer and the PDP Display

If your PDP Display screen remains blank after using the previous procedure, check your video controller and computer system; your PDP Display is functioning properly.

Warning Messages

You can even view the screen at a resolution of 1920 x 1080. However, you will receive the following message for a minute; You can choose to change the screen resolution or stay in the current mode during that time. And if the resolution is more than 85Hz, you will see the black screen because the

PDP Display does not support over 85Hz.

Note

Refer to Specifications > Preset Timing Modes for the resolutions or frequencies supported by the PDP

Display.

Maintenance and Cleaning

1) Maintaining the PDP Display Case.

Clean with a soft cloth after disconnecting the power cord.

Troubleshooting

• Do not use benzene, thinner or other flammable substances, or a wet cloth.

2) Maintaining the Flat Panel Display Screen.

Clean with a soft cloth (cotton flannel) smoothly.

• Never use acetone, benzene or thinner.

(They may cause flaws or deformation of the screen surface.)

• The user will be required to pay costs and related expenses for repairing damages caused.

Symptoms and Recommended Actions

Note

A PDP Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the PDP Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer.

1.

Check if the power cord and the video cables are properly connected to the computer.

2.

Check if the computer beeps more than 3 times when booting.

(If it does, request an a service for the main board of the computer.)

3.

If you installed a new video card or if you assembled the PC, check if you installed the Adaptor

(video).

4.

Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz.

(Do not exceed 60Hz when using the maximum resolution.)

5.

If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel −> System −> Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver.

Check List

Note

• The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Problems related to the Installation (PC Mode)

Note

Problems related to the PDP Display installation and their solutions are listed.

Q: The PDP Display screen flickers.

A: Check if the signal cable between the computer and the PDP Display is securely connected.

Troubleshooting

(Refer to Connecting a Computer)

Problems related to the Screen

Note

Problems related to the PDP Display screen and their solutions are listed.

Q: The screen is blank and the power indicator is off.

A: Ensure that the power cord is firmly connected and the PDP Display is on.

(Refer to the Connecting a Computer)

Q: "Check Signal Cable" message.

A: Ensure that the signal cable is firmly connected to the PC or video sources.

(Refer to the Connecting a Computer)

A: Ensure that the PC or video sources are turned on.

Q: "Not Optimum Mode" message.

A: Check the maximum resolution and the frequency of the video Adaptor.

A: Compare these values with the data in the Preset Timing Modes Chart.

Q: The picture rolls vertically.

A: Check if the signal cable is securely connected. Re-connect it, if necessary.

(Refer to Connecting a Computer)

Q: The image is not clear; picture is blurred.

A: Run Frequency Coarse and Fine tuning.

A: Turn on again after removing all accessories (video extension cable, etc.)

A: Set the resolution and frequency to the recommended ranges.

Q: The picture image is unstable and shakes.

A: Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display. If not, reset them referring to the current Information under the PDP Display menu and Preset Timing Modes.

Q: Ghost images are shown in the picture.

A: Check if the resolution and frequency set for the computer video card falls in the range supported by the PDP Display. If not, reset them referring to the current Information under the PDP Display menu and Preset Timing Modes.

Q: The image is too light or too dark.

A: Adjusts the Brightness and Contrast.

(Refer to the Brightness, Contrast)

Q: The screen color is inconsistent.

A: Adjust color using Custom under OSD Color Adjustment menu.

Troubleshooting

Q: The color image is distorted by dark shadows.

A: Adjust color using Custom under OSD Color Adjustment menu.

Q: The color white is poor.

A: Adjust color using Custom under OSD Color Adjustment menu.

Q: The Power Indicator blinks.

A: The PDP Display is currently saving the changes made to the settings to the OSD memory.

Q: The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. The PDP Display is using its power management system. Press any key on the keyboard.

A: The PDP Display is using its power management system. Press a key on the keyboard.

Q: The screen is blank and it is blinking.

A: If you see the "TEST GOOD" message on the screen when you pressing the MENU button, check the cable connection between the PDP Display and the computer to ensure that the connector is properly connected.

Problems related to Audio

Note

Problems related to audio signals and their solutions are listed below.

Q: No sound.

A: Ensure that the audio cable is firmly connected to both the audio-in port on your PDP Display and the audio-out port on your sound card.

(Refer to the Connecting a Computer)

A: Check the volume level.

Q: The sound level is too low.

A: Check the volume level.

A: If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program.

Q: The sound is too high or too low.

A: Adjusts the Treble and Bass to the appropriate levels.

Problems related to the Remote Control

Note

Problems related to the remote control and their solutions are listed.

Q: The remote control buttons do not respond.

A: Check the polarities (+/-) of the batteries.

A: Check if the batteries are empty.

A: Check if the power is on.

Troubleshooting

A: Check if the power cord is securely connected.

A: Check if a special fluorescent or neon lamp is on in the vicinity.

Q & A

Q: How can I change the frequency?

A: The frequency can be changed by reconfiguring the video card.

Note

That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

Q: How can I Adjust the resolution?

A: Windows XP:

Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.

A: Windows ME/2000:

Set the resolution in the Control Panel → Display → Settings.

* Contact the video card manufacturer for details.

Q: How can I set the Power Saving function?

A: Windows XP:

Control Panel → Appearance and Themes → Display → Enable the powersaving feature in

Screen Saver.

Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).

A: Windows ME/2000:

Control Panel → Display → Screen Saver.

Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).

Q: How can I clean the outer case/PDP Panel?

A: Disconnect the power cord and then clean the PDP Display with a soft cloth, using either a cleaning solution or plain water.

Do not leave any detergent or scratches on the case. Do not let any water enter the PDP Display.

Q: How can I play the video?

A: The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play the video. Note that some of the codecs can be incompatible.

Note

Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.

Specifications

General

General

Model Name SyncMaster P64FP

SyncMaster P64FT

PDP Panel

Size

Display Area

Pixel Pitch

Synchronization

Horizontal

Vertical

64 inches / 162 cm

1416.96 mm (H) x 797.04 mm (V)

0.738 mm (H) x 0.738 mm (V)

30~81 kHz

56~75 Hz

Display Color

16.77M

Resolution

Optimum resolution

Maximum resolution

Maximum Pixel Clock

165MHz (Analog, Digital)

1920 x 1080 @ 60 Hz

1920 x 1080 @ 60 Hz

Power Supply

This product supports 100 - 240 V.

Since the standard voltage may differ from country to country, please check the label on the back of the product.

Signal connectors

DVI-D In/Out(Can connect up to 10 PDP display units.), D-sub, AV(Composite, CVBS),

HDMI, RS232C In/Out PC Audio In, Audio In(Stereo), Audio Out(Stereo).

Dimensions (W x H x D) / Weight

1503.5 x 894.0 x 99.4 mm / 52.0 kg,

59.1 x 35.1 x 3.9 inches / 114 lbs

VESA Stand

676 mm x 407mm

Environmental considerations

Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)

Humidity : 20 % ~ 80 %, non-condensing

Specifications

Environmental considerations

Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)

Humidity : 5 % ~ 95 %, non-condensing

Plug and Play Capability

This PDP Display can be installed on any Plug & Play compatible system. The interaction of the PDP Display and the computer systems will provide the best operating conditions and PDP Display settings. In most cases, the PDP Display installation will proceed automatically, unless the user wishes to select alternate settings.

Dot Acceptable

TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED,

GREEN, BLUE and WHITE Color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems.

For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800.

Note

Design and specifications are subject to change without prior notice.

Class B (Information Communication equipment for residential use)

This device is registered for EMC requirements for home use (Class B). It can be used in all areas.

(Class B equipment emits less electromagnetic waves than Class A equipment.)

[Recommendation] - EU Only (P64FT Model Only)

Hereby, Samsung Electronics, declares that this [PDP Display] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC

(USA only)

Dispose unwanted electronics through an approved recycler.

To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect Or call, (877) 278 - 0799

FCC INFORMATION FOR THE CONSUMER (P64FT Model Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

Specifications

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technical for help.

This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two

Conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesirable operation.

Note

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

PowerSaver

This PDP Display has a built-in power management system called PowerSaver. This system saves by switching your PDP Display to low-power mode when it has not been used for a certain amount of time. The PDP Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your PDP Display OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.

PowerSaver

State

Power Indicator

Power Consumption

(Typical)

Normal Operation

On

550 watts

Power saving mode

Blinking

2 watts

Power off

Off

0 watt

Note

• The actual power consumption may be different from the indicated power consumption if the system condition or settings are changed.

• To stop any power consumption, disconnect the power cable on the back. Be sure to disconnect the power if you intend to stay away from home for many hours.

Specifications

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows.

Display Mode

IBM, 640 x 350

IBM, 720 x 400

IBM, 640 x 480

MAC, 640 x 480

MAC, 832 x 624

MAC, 1152 x 870

VESA, 640 x 480

VESA, 640 x 480

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 800 x 600

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1024 x 768

VESA, 1152 x 864

VESA, 1280 x 768

VESA, 1280 x 960

VESA, 1280 x 1024

VESA, 1280 x 1024

VESA, 1360 x 768

VESA,1600 x 1200

VESA,1920 x 1080

56.476

60.023

67.500

47.776

60.000

63.981

79.976

47.712

75.000

67.500

Horizontal Vertical Fre- Pixel Clock Sync Polarity

Frequency quency (Hz) (MHz) (H/V)

(kHz)

31.469

31.469

70.086

70.087

25.175

28.322

+/-

-/+

31.469

35.000

49.726

59.940

66.667

74.551

25.175

30.240

57.284

-/-

-/-

-/-

68.681

37.861

37.500

35.156

37.879

48.077

46.875

48.363

75.062

72.809

75.000

56.250

60.317

72.188

75.000

60.004

100.000

31.500

31.500

36.000

40.000

50.000

49.500

65.000

+/+

+/+

+/+

-/-

-/-

-/-

-/-

+/+

70.069

75.029

75.000

59.870

60.000

60.020

75.025

60.015

60.000

60.000

75.000

78.750

108.000

79.500

108.000

108.000

135.000

85.500

162.000

148.500

+/+

+/+

+/+

+/+

-/-

+/+

+/+

-/+

+/+

+/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal

Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency. Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called the Vertical

Frequency or Refresh Rate. Unit: Hz

Information

For Better Display

Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for PDP.

• Resolution: 1920 x 1080

• Vertical frequency (refresh rate): 60 Hz

PDP panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED,

GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems.

• For example, the number of PDP sub pixels contained in this product are 6,220,800.

When cleaning the monitor and the panel outside, please apply the recommended small amount of cleaner by using a soft cloth to polish. Do not force the PDP area but rub softly.

If excessive force is applied, you may stain it.

If you are not satisfied with the picture quality, you can get better quality of picture by performing the "Auto Adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after the automatic adjustment, use the

Fine/Coarse adjustment function.

When viewing a fixed screen for an extended period of time, a residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.

PRODUCT INFORMATION (Image Retention Free)

What is Image Retention ?

Image retention may not occur when a PDP panel is operated under normal conditions.

Normal conditions are defined as continuously changing video patterns. When the PDP panel is operated for a long time with a fixed pattern .

Phosphor degradation may occur and the brightness is decreased. To prevent this, the video pattern should be changed from time to time.

When viewing a still screen for a long time, the brightness of any part which was bright in the previous fixed pattern becomes lower than that of its surroundings.

Information

Power Off, Screen Saver, or Power Save Mode

• Turn the power off for 4 hours after 20 hours in use

• Turn the power off for 2 hours after 12 hours in use

• Set the Monitor to power off with the PC Display Properties Power Scheme.

• Use a Screen saver if possible - Screen saver in one color or a moving image is recommended.

Change the Color Information periodically

Note

Use Two different colors

Rotate the Color Information with 2 different colors every 30 minutes.

• Avoid using a combination of characters and background color with large difference in luminance.

Avoid using Grey colors, which can cause Image retention easily.

Avoid: Colors with big difference in luminance (Black & White, Grey)

Change the characters color periodically

Information

• Use Bright colors with little difference in luminance.

- Cycle : Change the characters color and background color every 30 minutes

• Every 30 minutes, change the characters with movement.

• All area display Moving image together with Logo periodically.

- Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.

• The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also

Warranty service will be limited based on instruction guide.

Apply the Screen Scroll function on Product

• Apply the Screen Scroll function

- Symptom: Horizontal Bar with Black Color move up and down.

Note

Please check CD's User Guide at "OSD Function", some model's will not available.

Apply the Screen Pixel function on Product

• Apply the Screen Pixel function

- Symptom: Dot with Black Color move up and down.

• Apply the Screen Bar function

- Symptom: Horizontal / Vertical Bar with Black Color move up and down.

Information

Note

Please check CD's User Guide at "OSD Function", some model's will not available.

Apply the Screen Erasing function on Product

• Apply the Screen Erasing function

- Symptom: 2 Vertical blocks move with erasing the display

Note

Please check CD's User Guide at "OSD Function", some model's will not available.

Appendix

Contact SAMSUNG WORLDWIDE

Note

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.

U.S.A

CANADA

MEXICO

North America

1-800-SAMSUNG (726-7864) http://www.samsung.com

1-800-SAMSUNG (726-7864) http://www.samsung.com

01-800-SAMSUNG (726-7864) http://www.samsung.com

0800-333-3733

0800-124-421

Latin America

ARGENTINA

BRAZIL http://www.samsung.com

http://www.samsung.com

CHILE

COLOMBIA

COSTA RICA

DOMINICA

ECUADOR

EL SALVADOR

GUATEMALA

HONDURAS

JAMAICA

NICARAGUA

PANAMA

PERU

PUERTO RICO

4004-0000

800-SAMSUNG (726-7864)

01-8000112112

0-800-507-7267

1-800-751-2676

1-800-10-7267

800-6225

1-800-299-0013

800-27919267

1-800-234-7267

00-1800-5077267

800-7267

0-800-777-08

1-800-682-3180 http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

TRINIDAD & TO-

BAGO

1-800-SAMSUNG (726-7864) http://www.samsung.com

VENEZUELA 0-800-100-5303 http://www.samsung.com

ALBANIA

AUSTRIA

BELGIUM

BOSNIA

BULGARIA

CROATIA

Europe

42 27 5755

0810 - SAMSUNG (7267864, €

0.07/min)

02-201-24-18

http://www.samsung.com

http://www.samsung.com/be

(Dutch) http://www.samsung.com/be_fr

(French)

05 133 1999

07001 33 11

http://www.samsung.com

062 SAMSUNG (062 726 7864) http://www.samsung.com

Appendix

Europe

800 - SAMSUNG (800-726786) http://www.samsung.com

CZECH

DENMARK

FINLAND

FRANCE

GERMANY

70 70 19 70

030 - 6227 515

01 48 63 00 00

01805 - SAMSUNG (726-7864,

€ 0,14/Min) http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

GREECE

HUNGARY

ITALIA

KOSOVO

LUXEMBURG

MACEDONIA

MONTENEGRO

NORWAY

POLAND

2106293100 http://www.samsung.com

06-80-SAMSUNG (726-7864) http://www.samsung.com

800-SAMSUNG (726-7864)

+381 0113216899 http://www.samsung.com

261 03 710

023 207 777

020 405 888

NETHERLANDS 0900-SAMSUNG

(0900-7267864) ( € 0,10/Min)

815-56 480

0 801 1SAMSUNG (172678)

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

PORTUGAL

RUMANIA

022-607-93-33

80820 - SAMSUNG (7267864) http://www.samsung.com

http://www.samsung.com

SERBIA

SLOVAKIA

0700 SAMSUNG (0700 726

7864) http://www.samsung.com

0800 - SAMSUNG (0800-726

786) http://www.samsung.com/sk

SPAIN 902 - 1 - SAMSUNG (902 172

678) http://www.samsung.com

SWEDEN

SWITZERLAND

0771 726 7864 (SAMSUNG) http://www.samsung.com

0848 - SAMSUNG (7267864,

CHF 0.08/min) http://www.samsung.com/ch http://www.samsung.com/ ch_fr/(French)

U.K

EIRE

0330 SAMSUNG (7267864)

0818 717100 http://www.samsung.com

http://www.samsung.com

LITHUANIA

LATVIA

ESTONIA

TURKEY

8-800-77777

8000-7267

800-7267

444 77 11 http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

RUSSIA

GEORGIA

8-800-555-55-55

8-800-555-555

CIS

http://www.samsung.com

Appendix

ARMENIA

AZERBAIJAN

KAZAKHSTAN

UZBEKISTAN

KYRGYZSTAN

TADJIKISTAN

UKRAINE

BELARUS

MOLDOVA

CIS

0-800-05-555

088-55-55-555

-

-

8-10-800-500-55-500 (GSM:

7799) http://www.samsung.com

8-10-800-500-55-500

00-800-500-55-500

8-10-800-500-55-500

0-800-502-000 http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com/ua

810-800-500-55-500

00-800-500-55-500 -

http://www.samsung.com/ua_ru

AUSTRALIA 1300 362 603

NEW ZEALAND 0800 SAMSUNG (0800 726

786)

CHINA

HONG KONG

Asia Pacific

400-810-5858

(852) 3698 - 4698 http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com/hk

INDIA http://www.samsung.com/ hk_en/ http://www.samsung.com

INDONESIA

3030 8282

1800 3000 8282

0800-112-8888 http://www.samsung.com

JAPAN

MALAYSIA

PHILIPPINES

SINGAPORE

THAILAND

TAIWAN

VIETNAM

021-5699-7777

0120-327-527

1800-88-9999

1-800-10-SAMSUNG

(726-7864)

1-800-3-SAMSUNG (726-7864)

1-800-8-SAMSUNG (726-7864) http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

02-5805777

1800-SAMSUNG (726-7864) http://www.samsung.com

1800-29-3232 http://www.samsung.com

02-689-3232

0800-329-999

1 800 588 889 http://www.samsung.com

http://www.samsung.com

Middle East

IRAN 021-8255 http://www.samsung.com

http://www.samservice.com

Appendix

OMAN

KUWAIT

BAHRAIN

EGYPT

JORDAN

MOROCCO

183-2255

8000-4726

08000-726786

800-22273

080 100 2255

SAUDI ARABIA 9200-21230

Middle East

800-SAMSUNG (726-7864)

U.A.E

800-SAMSUNG (726-7864) http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

http://www.samsung.com

NIGERIA

Africa

0800-SAMSUNG (726-7864) http://www.samsung.com

SOUTH AFRICA 0860-SAMSUNG (726-7864) http://www.samsung.com

Terms

Dot Pitch

Vertical Frequency

Horizontal Frequency

Interlace and Non-Interlace

Methods

Plug & Play

Resolution

The image on a monitor is composed of red, green and blue dots.

The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm

The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh

Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz

Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non-Interlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.

This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard

VESA DDC for the Plug & Play function.

The number of horizontal and vertical dots used to compose the screen image is called the 'resolution'. This number shows the accuracy of the display. A high resolution is good for performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1920 x 1080, this means the screen is composed of 1920 horizontal dots (horizontal resolution) and

1080 vertical lines (vertical resolution).

Appendix

SRS TS XT

Multiple Display Control

(MDC)

This feature outputs sonorous and vivid 3D sound as for 5.1 channel speaker sound but through a 2-channel speaker. It has a good effect when stereo signals are input.

A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC.

RS-232C, a standard of serial communication, is used for communicating between a PC and a display.

Correct Disposal

Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

Correct disposal of batteries in this product - Europe only

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in

EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment.

To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

Note

The rechargeable battery incorporated in this product is not user replaceable. For information on its replacement, please contact your service provider.

Authority

Information in this document is subject to change without notice.

© 2011 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co.,

Ltd. is strictly forbidden.

Appendix

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPM and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR ® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

TruSurround XT, SRS and the symbol are trademarks of SRS Labs,Inc.

TruSurround XT technology is incorporated under license from SRS Labs,

Inc.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents