NUUO Intelligent Surveillance Solution User's manual
Below you will find brief information for Intelligent Surveillance Solution. This solution provides comprehensive surveillance management software, allowing you to activate, schedule recording, setup smart guard and configure system settings. It includes features like live view, playback, remote live viewer, backup, and verification tool.
Advertisement
Advertisement
The Intelligent Surveillance Solution
Surveillance Management Software user’s manual
Ver. 99.280.7C19.001
Intelligent Surveillance Solution
Table of Contents
TABLE OF CONTENTS
Smart Phone Client Installation...................................................................24
Activate IP Camera License(s)...................................................................25
Start Recording & Smart Guard .................................................................30
1.5.3 Connect/ Disconnect.....................................................................38
1.5.5 Duplicate Camera ..........................................................................38
page1
Intelligent Surveillance Solution
Table of Contents
2.5.2 Record Display Window .................................................................44
2.5.7 To Withdraw the Record.................................................................46
2.6.1 Unusual Event-General Motion......................................................47
2.6.2 Unusual Event-Foreign Object .......................................................48
2.6.3 Unusual Event-Missing Object........................................................49
2.6.4 Unusual Event- Focus Lost / Camera Occlusion .........................49
2.12.3 Counting Application ...................................................................55
2.12.4 Counting Application (Diagram)................................................55
2.12.6 Export and Backup Log ................................................................57
page2
Intelligent Surveillance Solution
Table of Contents
2.13.6 POS Overlay Setting ......................................................................60
2.14.1 Add Remote Playback Site..........................................................61
2.14.2 Access Remote Playback Site.....................................................61
3.1.1 Load Preset Modes..........................................................................63
3.1.2 Insert a New Schedule Manually ..................................................65
3.3 Adjust the Scheduled Setting: ..............................................................67
3.4.1 Pre-record/ Post-record Time.........................................................68
3.4.3 Encoded Options.............................................................................69
4.1.1 Camera Event - Assign a Camera Event.....................................72
4.1.2 Camera Event – Basic Setting of camera event ........................72
4.1.3 Camera Event - Signal Lost ............................................................73
4.1.4 Camera Event - General Motion ..................................................73
4.1.5 Camera Event - Foreign Object....................................................74
4.1.6 Camera Event - Missing Object.....................................................75
4.1.7 Camera Event - Lose Focus ...........................................................77
4.1.8 Camera Event - Camera Occlusion.............................................78
4.1.9 POS Event - Assign a POS Event ....................................................79
4.1.10 Digital Input Event - Digital Input Event......................................80
4.1.11 System Event - Assign a System Event ........................................81
4.1.12 System Event – Basic Setting ........................................................81
4.1.13 System Event - Disk Space Exhausted ........................................82
4.1.14 System Event - System Health Unusual .......................................82
4.1.15 System Event – Resource Depleted............................................82
4.1.16 System Event – Network................................................................83
4.2.1 Action - Assign a action type ........................................................84
4.2.2 Action Type - On Screen display...................................................85
page3
Intelligent Surveillance Solution
Table of Contents
4.2.3 Action Type - Play Sound................................................................85
4.2.4 Action Type - Send E-mail...............................................................86
4.2.5 Action Type - Phone Call................................................................87
4.2.6 Action Type - PTZ Preset Go ...........................................................87
4.2.7 Action Type – DI/DO........................................................................88
4.2.8 Action Type –Send a SMS message..............................................89
4.2.9 Action Type – Send to Central Server...........................................89
4.2.10 Action Type – Send snapshot to FTP ...........................................89
4.2.11 Action Type – Popup E-Map on Event .......................................90
5.2.2 IP Camera / Video Server Setting panel......................................98
5.2.3 Camera Parameter.........................................................................99
5.11 Save/ Load Configuration ................................................................114
5.14.1 Live Streaming Server..................................................................117
5.14.2 Remote Playback Server............................................................120
5.14.4 Remote Desktop ..........................................................................124
5.14.5 Central Management Service...................................................125
5.15 About Main Console..........................................................................127
page4
Intelligent Surveillance Solution
Table of Contents
6.1.1 Add/Edit/Delete Map...................................................................129
6.1.2 Add/Rotate/Delete Device Indicator........................................130
6.2.1 Device and Map Tree list..............................................................132
6.2.3 Information and Preview window...............................................133
6.3.1 Adjust layout window....................................................................134
7.4 Counting Application (Diagram).......................................................139
7.6 Export and Backup Log.......................................................................141
8.1 Backup Recorded file(s)......................................................................144
9.1.7 Monitor Display Setting .................................................................154
9.2 Server/Group/Camera........................................................................157
9.2.2 Connect/Disconnect camera.....................................................157
page5
Intelligent Surveillance Solution
Table of Contents
9.6.1 Add Remote Playback Site..........................................................162
9.6.2 Access Remote Playback Site.....................................................162
1.1Execute Verification Tool ..................................................................166
1.2 Verification Tool Overview ..............................................................167
1.3 Verify Image/Video..........................................................................168
B. License Management Tool ...................................................................169
1.1 License Management Tool Overview ...........................................170
1.2 Activate/Transfer License ................................................................172
C. Resource Management Tool...............................................................176
1.1 Execute Resource Management tool...........................................176
1.2 System Resource Overview.............................................................176
1.3 Advanced Resource Report...........................................................178
1.2 Export Configurations.......................................................................185
1.1 Configuration from NUUO server .......................................................186
1.2 Configuration from 3G Mobile Phone...............................................187
1.2.1 BenQ-Siemens E81 .........................................................................187
page6
Intelligent Surveillance Solution
Table of Contents
APPENDIX B – PDA / SMART PHONE CLIENT....................................................194
1.1 Install PDA / Smart Phone Client ........................................................194
1.2 Execute PDA / Smart Phone Client....................................................194
1.2.1 Main Console setting ....................................................................194
1.2.2 Execute and Login ........................................................................195
1.3 PDA/Smart Phone Client Overview ...................................................196
APPENDIX C - REMOTE DESKTOP TOOL ...........................................................199
page7
SYSTEM REQUIREMENT
Total FPS at CIF
1200~600 600~480
CPU
Intel Core
2 Quad
Q6600
Intel Core
2 Duo
E6400
RAM
2 GB 1 GB
Mother- board
Intelligent Surveillance Solution
System Requirement
480~240
Intel
Pentium D
930
1 GB
240~120
Intel P4 2.8
GHz
512 MB
120~
Intel P4 2.8
GHz
512 MB
Intel 945, 965 chip or above, Intel Chipset and ASUS Vender recommended
Display
Ethernet
ATi Radeon 9200 , nVIDIA GeForce FX-5200 , Intel 945G/965G or above (ATi recommended)
100 baseT or above, Gigabit LAN recommended
Hard Disk
80 GB or above
OS
MS Windows 2000 / XP pro sp2 / 2003/Vista page8
Intelligent Surveillance Solution
Installation
INSTALLATION
The Installation CD contains the software you need to run the complete system. If you are installing the system on multiple PCs, install the appropriate software for each PC:
- Server Application: All functions of NVR/DVR/Hybrid NDVR systems include MainConsole, Playback, Remote Live Viewer, Backup, and
Verification Tool.
- Client Application: Remote functions of NVR/DVR/Hybrid NDVR systems include Playback, Remote Live Viewer, Backup, and Verification Tool.
- Remote Desktop Tool: The tool to access main console and setup configuration remotely.
- DVR Driver: The tool to detect the type of capture cards and install the proper driver automatically.
- PDA Client: Client application in PDA device.
- Smart Phone Client: Client application in smart phone device.
- Related Link: To gather more information, such as User Manual,
Installation guide and Hardware Requirement.
The following sections describe installation of each element of the
Intelligent Surveillance System. page9
Intelligent Surveillance Solution
Installation
Server Application Installation
Step 1: Insert the Installation CD. Run Autorun Tool from the CD-ROM directly to start the installation.
Step 2: Select “Server Application Installation” then click on it.
Step 3: There are 4 system types of options in “System Setup Tool” window, select one and click Next to start the Installshield of Server package.
- NUUO IP Surveillance System/Trial System
- NUUO MPEG-4 Hybrid System
- NUUO H.264 Hybrid System
- NUUO Full D1H.264 Hybrid System
Note:
The SetupTool will detect the type of capture cards installs on PC and enable the options of system types automatically. page10
Intelligent Surveillance Solution
Installation
Step 4: In the InstallShield Wizard dialog box, click Next to continuous.
Step 5: Check the option “I accept the terms of the license agreement”.
Click Next to continuous.
Step 6: Please enter your name and the company name for which you work. Click Next to continuous. page11
Step 7: Select “Complete Setup Type” or “Custom Setup Type” to install the System.
Intelligent Surveillance Solution
Installation
COMPLETE SETUP TYPE
Install all program features into the default directory.
- Check the option “Complete”, and then click “Next”. All program features will be installed. [Require the most disk space.]
CUSTOM SETUP TYPE
Install the system to a preferred directory. Or select whichever program feature(s) to install. This is recommended for advanced users.
- Check the option “Custom”, and then click “Next”.
- Select appointed folder where setup will install files to. Click
“Change” to modify the installation directory.
- Select the features setup will install. There are 4 features to choose in the server setup process: MainConsole, Playback,
LiveView, Backup, and Verification tool. Click “Next” after page12
Intelligent Surveillance Solution
Installation
confirmation.
Step 8: Click install to start the installation.
Step 9: Click Finish after installing the system completely. page13
Intelligent Surveillance Solution
Installation
Client Application Installation
Step 1: Insert the Installation CD. Run autostartup.exe
CD-ROM directly to start the installation.
from the
Step 2: Select “Client Application Installation” then click on it.
Step 3: In the InstallShield Wizard dialog box, click Next to continuous.
Step 4: Check the option “I accept the terms of the license agreement”.
Click Next to continuous. page14
Intelligent Surveillance Solution
Installation
Step 5: Please enter your name and the company name for which you work. Click Next to continuous.
Step 6: Select “Complete Setup Type” or “Custom Setup Type” to install the System.
COMPLETE SETUP TYPE
Install all program features into the default directory.
- Check the option “Complete”, and then click “Next”. All program features will be installed. [Require the most disk space.]
CUSTOM SETUP TYPE
Install the system to a preferred directory. Or select whichever program feature(s) to install. This is recommended for advanced users.
- Check the option “Custom”, and then click “Next”. page15
Intelligent Surveillance Solution
Installation
- Select appointed folder where setup will install files to. Click
“Change” to modify the installation directory.
- Select the features setup will install. There are 3 features to choose in the server setup process: Playback, LiveView,
Backup, and Verification. Click “Next” after confirmation. page16
Intelligent Surveillance Solution
Installation
Step 7: Click “Install” to start the installation.
Step 8: Click “Finish” after installing the system completely. page17
Intelligent Surveillance Solution
Installation
Remote Desktop Tool
Remote Desktop Tool allow user remote to access Main Console System and setup configuration.
Step 1: Insert the Installation CD.
Run autostartup.exe
CD-ROM directly to start the installation.
from the
Step 2: Select “Remote Desktop Tool” then click on it.
Step 3: In the InstallShield Wizard dialog box, click Next to continuous.
Step 4: Check the option “I accept the terms of the license agreement”.
Click Next to continuous. page18
Intelligent Surveillance Solution
Installation
Step 5: Please enter your name and the company name for which you work. Click Next to continuous.
Step 6: Select “Complete Setup Type” or “Custom Setup Type” to install the System.
COMPLETE SETUP TYPE
Install all program features into the default directory.
- Check the option “Complete”, and then click “Next”. All program features will be installed. [Require the most disk space.]
CUSTOM SETUP TYPE
Install the system to a preferred directory. Or select whichever program feature(s) to install. This is recommended for advanced users.
- Check the option “Custom”, and then click “Next”.
- Select appointed folder where setup will install files to. Click
“Change” to modify the installation directory. page19
Intelligent Surveillance Solution
Installation
- Select the features setup will install.
Step 7: Click “Install” to start the installation.
Step 8: Click “Finish” after installing the system completely. page20
Intelligent Surveillance Solution
Installation
DVR Driver Installation
Driver Install Tool help user to auto detect type of capture card and install corresponding drivers.
Step 1: Insert the Installation CD.
Run autostartup.exe
CD-ROM directly to start the installation.
from the
Step 2: Select “DVR Driver Installation” then click on it.
Step 3: In the NUUODriver Setup Wizard dialog box, click Next to continuous.
Step 4: Check the “License agreement”. Click “I Agree” to continuous. page21
Intelligent Surveillance Solution
Installation
Step 5: Installing NUUODriver.
Step 6: Click “Finish” after installing the system completely, and then choose to reboot now or later. page22
Intelligent Surveillance Solution
Installation
PDA Client Installation
Step 1: Connect PDA device to the PC.
Step 2: Insert the installation CD, click “PDA Client Installation” to automatically install the client application in device.
Note:
If you do not have Microsoft® ActiveSync installed, a message will appear “Can not find ActiveSync. Please reinstall
ActiveSync and than run this installation again.”
Step 3: Check the client application is installed completely in PDA device. page23
Intelligent Surveillance Solution
Installation
Smart Phone Client Installation
Step 1: Connect Smart Phone device to the PC.
Step 2: Insert the installation CD, click “Smart Phone Client Installation” to automatically install the client application in device.
Note:
If you do not have Microsoft® ActiveSync installed, a message will appear “Can not find ActiveSync. Please reinstall
ActiveSync and than run this installation again.”
Step 3: Check the client application is installed completely in smart phone device. page24
Intelligent Surveillance Solution
Quick Start
Quick Start
Execute Main Console
Step 1: Execute Main Console.
Step 2: Enter your own password into the edit box, enter it again for double confirm and then click on OK. Enjoy NUUO Intelligent Surveillance
Solution.
Activate IP Camera License(s)
Step 1: Open “License Manager” Tool in Config menu.
Step 2: Select “Activate” tab, check the PC in
“On line” network environment.
Step 3: Insert the SN, SN file or dongle to activate license.
Step 4: After software license is activated successfully, please restart Main Console.
Note:
for advanced settings.
Step2
Step 3 page25
Intelligent Surveillance Solution
Quick Start
Install IP camera(s)
Step 1: Setup the IP camera(s) by referring to the user manual provided by the IP camera manufacturer.
Step 2: Make sure you can access this camera through IE browser.
Step 3: Add the IP camera(s) to the system by following steps.
Add IP camera(s)
Step 1: Go to Start > All Programs > NUUO >
Main Console.
Step 3
Step 2: Type in user name and password and log in to the system.
Step 3: In Main Console, go to Config > Setting to obtain the Setting panel.
Step 4: Go to Camera tab.
Note:
If your IP cameras support UPnP, follow step 5. Otherwise, follow step 8.
Step 5: Click on “Search” to find out the IP cameras at this local area network
(LAN).
Note:
Search function only available when the IP cameras support UPnP.
Step 6: Select one of the IP cameras that are available; check this camera and enter the username and password.
Step 7: Click OK to add the camera.
Step 8: Click “Insert” to insert the IP cameras.
Step 5
Step 4
Step 8
Step 12 page26
Intelligent Surveillance Solution
Quick Start
Step 9: Enter the IP address or domain name (check the “Use DNS” option), Http Port, Username, and Password.
Step 10: Click “Auto Detect”
Step 11: Click OK to add the camera.
Step 12: Click OK to exit Setting panel.
Step 9
Step 10
Step 11 page27
Intelligent Surveillance Solution
Quick Start
Set Schedule
Step 1: Go to Start > All Programs > NUUO > Main Console.
Step 2: Type in user name and password and log in the system.
Step 3: Click on “Schedule".
Step 4: The default schedule is “always record' when a camera is newly inserted.
Step 5: Choose a camera and then click on
“Configure” or just double click on the schedule bar to modify the recording mode.
Step 6: Click OK to update the recording schedule.
Step 4
Step 7: Click OK again to go back to Main Console.
Step 5
Step 3 page28
Intelligent Surveillance Solution
Quick Start
Set Smart Guard
Step 1: Go to Start > All Programs > NUUO > Main
Console.
Step 2: Type in user name and password and log in the system.
Step 3: Click on “Guard”.
Step 4: Select a camera and then click on “Insert
Event.”
Step 5: Take General Motion for example, select
General Motion as the event type and then click on OK.
Step 6: In Alarm Event Configuration panel, define your own detection zone, sensitivity and interval. After that, click on OK to save the configuration.
Step 7: Click OK to go back to Main Console.
Step 4
Step 5
Step 3
Step 6 page29
Start Recording & Smart Guard
Step 1: Go to Start > All Programs >NUUO
> Main Console.
Step 2: Type in user name and password and log in the system.
Step 3: Click on “Start”.
Step 4: Click on “Start Recoding
Schedule” and “Start Smart
Guard System” to enable the two functions.
Intelligent Surveillance Solution
Quick Start
Step 3
Step 4 page30
Intelligent Surveillance Solution
Quick Start
Playback
Step 1: Go to Start > All Programs > NUUO > Main Console.
Step 2: Type in user name and password and log in the system.
Step 3: Click on “Playback”.
Step 4: In Playback, click on “Open Record”
Step 5: Select a specific day from the calendar
Step 3 and click on “Show Records” to make sure the video is available, left click on mouse and drag to select a video clip to replay, user can also select multiple channels to replay at the same time.
Step 6: The recorded files are ready to view now.
Step 5 Step 4 page31
Intelligent Surveillance Solution
1. MainConsole
1. Main Console
This is the main operation system - to activate, schedule recording, setup smart guard and configure system setting. page32
Intelligent Surveillance Solution
1. MainConsole
Exit
Minimize
E X I
I
T :
:
Shut down the Surveillance System or log out current user.
M I
I
N I
I
M I
I
Z E :
:
Screen Division
Minimize the Main Console window.
S C R E E N D I
I
V I
I
S I
I
O N :
:
Allocate the sub-screen display by clicking on the desired layout icon.
To switch to single camera display, double click on a particular sub-screen.
Double click on the screen again to regain previous screen division layout.
Divide into
1 screen(s)
Divide into
4 screen(s)
Divide into
6 screen(s)
Divide into
9 screen(s)
Divide into
10 screen(s)
Divide into
13 screen(s)
Divide into
16 screen(s)
Divide into
N screen(s)
Divide into
13 screen(s)
Divide into
17 screen(s)
Switch to
Full screen
Rotate all screens page33
Intelligent Surveillance Solution
1. MainConsole
1.1 Start
S T A R
Start
R
T :
:
Click on the Start icon and select from the drop down menu to activate/ deactivate: (a) Recording Schedule System, (b) Smart Guard System, or
(c) Counting Application. Or select Start/Stop Monitor All to activate/ deactivate all the functions at once.
The Start menu also include the option to Enable Secondary Display, and open monitor tools, such as open event report to monitor smart guard event; open E-map window to monitor all devices with map indicator; open Resource Report to check system status; open IO Control panel to monitor the DI/DO status and manual triggering the DO devices; or lock
the system here. See page 108 for more details about secondary display.
Note:
1. When activating any of the monitor functions of Smart Guard, system would consider the current screen status as normal. Therefore, if you want to, for example, detect Missing Object, be sure the object needed to be protected is in its position at the moment you click Start button.
2. To automatically activate the Recording Schedule System, Smart
Guard System and Counting Application as the MainConsole starts, go to Config > Setting>General > Startup to setup the auto-startup functions. page34
Intelligent Surveillance Solution
1. MainConsole
3. As for Secondary Display, open event report, open E-map window, open Resource Report and open IO controls panel, MainConsole will keep the behaviors as the latest status when exiting the system.
P L A
Y
B A C K :
:
Playback Schedule Guard
Config
Click on the icon to get Playback Console. You can watch recorded video, search recorded video, adjust image of the stored data, save video/ pictures, print images, check log information and event records,
and set up recording function configuration. See PlayBack on page 41 for
detail.
S C H E
E
D U L E :
:
Organize recording time schedule and setup recorder configuration. See
Schedule on page 62 for detail.
G U A R D :
:
Add/edit type(s) of events that you want to detect; setup action(s)
responding to events. See Guard on page 71 for detail.
page35
C O N F
Intelligent Surveillance Solution
1. MainConsole
F
I
I
G :
Select from the drop down menu to modify general setting, user account settings, save/ load configuration settings, open License Manager, edit counting application and POS application, access log viewer and
backup files, or setup network services. See Config on page 91 for detail.
Note:
User account and License manager could only be enabled for users with administrator privilege.
Crystal Ball
Information
Window
PTZ Camera
Control
1.2 Crystal Ball
Indicate the working status of the system. Gray – at rest, Blue - recording, and Red – events detected. When the crystal ball is red, click it to open the event report then cancel the event(s).
1.3 Information Window
Display date, time, free Disk space, IP Camera Bitrate customized text and
Further information like Temperature, Fan speed, System Resource and
Network Utilization.
Note: To customize Information about window’s setting, go to Config >
Setting > General > Status Display. Click “Advanced Setting” for further information like Temperature, Fan speed, System Resource and Network
Utilization. page36
Intelligent Surveillance Solution
1. MainConsole
1.4 PTZ Camera Control
Control the movement of PTZ cameras. With cameras that support PTZ control, you can move, zoom, patrol, adjust the focus, and set preset points of the cameras.
1.4.1 Preset/ Go
Adjust the camera view until you are satisfied. Click on the Set icon and set up the view as the preset point 01. Adjust the camera view again and set up the preset point 02. Repeat the process until finish setting up all preset points. You can enter any names you want instead of the preset point 01, preset point 02, preset point 03…, click on the Go icon and view the result of your setting.
Note:
For the speed settings of PTZ camera, go to Config > Setting>PTZ
Config to setup the advanced settings.
1.4.2 Zoom
Click on the + and – signs to zoom in and zoom out the view.
1.4.3 Focus
You can select to have the camera focused near or far. To focus near means objects that are closer will be clearer than the objects that are further away. On contrast, to focus far means objects that are further will be clearer than the objects that are closer. Click on the Focus icon and select auto focus if you want the system to decide the focus point for you.
1.4.4 Patrol
Go to Patrol > Set Patrol to obtain the Patrol Setup dialog. From the left window, select the cameras that you would like to have in the patrol group. Align the cameras in order in the right window and adjust the time. Rename the group name if you want. After completing the setup, check the Active option, and then click OK.
You can setup up to four groups of auto patrol. To start or stop, click on the Patrol icon in the Main Console, and select Start Patrol or Stop Patrol. page37
Intelligent Surveillance Solution
1. MainConsole
1.5 On Screen Menu
Right click on the camera screen and get the
“On Screen Menu”, from which you can quickly adjust the setting of camera.
1.5.1 Enable Move
With cameras that support PT function, click the
“Enable move” function to adjust the current camera’s view by clicking on the display screen.
To cancel this function, right click on the screen and select Disable Move.
1.5.2 Enable Talk
With cameras that support two-way audio, select enable talk to utilize the function.
1.5.3 Connect/ Disconnect
Right click on the display screen and select Connect/ Disconnect to modify the connecting status of the camera.
1.5.4 Show Camera
Select the camera from the Show Camera Menu to display video on selected screen.
Note:
1. The camera list of show camera menu shows as the one in the right column of monitor display panel.
2. The change of displayed screen is only applied to the current display divisions.
1.5.5 Duplicate Camera
Select the camera from the Duplicate Camera Menu to duplicate camera video to selected screen.
Note:
1. The duplicated camera would add to the camera list of duplicate camera menu shows as the one in the right column of monitor display panel.
2. The change of display list will apply to all divisions and also the right column of monitor display. page38
Intelligent Surveillance Solution
1. MainConsole
1.5.6 Delete Camera
Click on Delete Camera to remove a camera from the display screen of the display screen.
Note:
1. The camera list of delete camera menu shows as the one in the right column of monitor display panel.
2. The settings will apply to all divisions and also the right column of monitor display.
1.5.7 Enable Digital PTZ
To enable the PTZ functions of the camera, select the “Enable digital PTZ
option”. Use mouse wheel or click on the + and – signs to zoom in and zoom out on the camera. The square flashing on the video grid indicate the correspondent view of the camera.
Note:
Enable Digital PTZ is the option function in IP+ software not in IP software.
1.5.8 Fix Aspect Ratio
For some special camera resolution, user can enable Fix Aspect Ratio to view original ratio video, or disable this option to stretch 3:4 to fit window.
1.5.9 Snapshot
Select the snapshot function to capture a specific video image frame immediately. You have the options to copy the image to clipboard or to save it. For further settings, select OSD option and POS option to export the image with date/time, camera number/name and POS text. If the digital PTZ function is enabled in display view, you can also decide either Full size or Selected
region as your snapshot region.
1.5.10 Manual Record
Start recording video by selecting manual record.
1.5.11 Toggle Fullscreen
Select it to view a specific channel with fullscreen. Press “ESC” to go back to original window. page39
Intelligent Surveillance Solution
1. MainConsole
1.6 Live Display
NUUO Live display is flexible to change channels and screen divisions.
Each screen divisions have the same display list, but have the different sequence.
Such like, when using Show/Duplicate/Delete Camera function to edit camera list, the operator will apply to all different screen divisions.
Note:
The camera list of all divisions is the same as the right column of monitor display tab on Config/Setting window, it means two monitors could have two different list.
Action Current division
Other division
Show camera
(add cam 1)
1
1
add to first free channel
Duplicate camera
(duplicate cam 2)
Delete camera
(delete cam 2”)
1 2
2”
1 2
1 2
add to first free channel
remove cam 2 and keep channel free
When using mouse to drag camera channel, the sequence change would only apply to original division.
Action Original
1 2
3 4
Drag cam 1 to cam 4
Current division
4 2
3 1
Other division
1 2 3
4
Not change sequence
Right click on the camera screen and get the On Screen Menu, from which you can quickly adjust the setting of camera. page40
Intelligent Surveillance Solution
2. Playback
2. PlayBack
Watch the recorded video, view and/or search for unusual events and recorded system information. page41
Intelligent Surveillance Solution
2. Playback
Scroll Bar
Exit
Minimize
Control
Cue Speed Zoom
FWD/REV:
Customize the speed on Setting panel.
Step FWD/REV:
Forward/reverse frame by frame.
M I
I
N I
I
M I
I
Z
E
:
:
Minimize the Playback console.
E X I
I
T :
:
Shut down the Playback console.
S C R O L L B A R :
:
Indicate the status of the playing video; drag it to where you want to review.
C O
N
T
R
O
L
:
:
Play, pause and stop the video.
C U E :
:
When playing video, click on the Cue In/ Cue Out icon at where you want to set as the starting/ ending point of a saved video clip. The Cue In and Cue Out time will be displayed on the Playback Information Window once they are set.
S
Z
P
O
E E
O
D
M
:
:
Control the speed of the playing video. Click + to speed up and – to speed down.
M
:
:
Zoom in and zoom out. Get a close up view of the recorded video; move to the spot you want to view by dragging the screen. page42
Intelligent Surveillance Solution
2. Playback
Browse Mode
Search Mode
Screen Division
Open Record
Audio Volume
Control
Information Window
2.1 Information Window
Display video date and time, current video status, cue in/ out points’ time, and speed.
2.2 Audio Volume Control
Adjust the sound level.
2.3 Screen Division
Allocate the sub-screen display by clicking on the desired layout icon. To switch to single camera display, double click on a particular sub-screen.
Double click on the screen again to regain previous screen division layout.
To view in the fullscreen mode, right click on the screen to trigger Toggle
Fullscreen function.
2.4 Browse Mode
Play the recorded video.
2.5 Open Record
Click on Open Record button to access the Date-Time Panel and withdraw the video record that you want to review. page43
2.5.1 Date Time Panel
Intelligent Surveillance Solution
2. Playback
2.5.2 Record Display Window
The record display window shows the information of the available video clips. It may show in calendar or list control view. For further details about how to modify the
record display window view, see page 59.
y
Remote Server Site: Open Remote
Playback Site Management dialog could select to access local machine or set up remote playback server. Select Folder option could directly access recorded data folder or use Recent List to access previous browser recorded folders.
Note:
To use Select Folder function need password of MainConsole. y
Refresh: To refresh the record display window y y
Log Viewer: To access the Log Viewer Tool
POS Search: To access POS Search Tool page44
Intelligent Surveillance Solution
2. Playback
y
Previous Days: To show recorded of previous recording date y
Next Days: To show recorded of next recording date
2.5.3 Date Time Period
Select the start and end time points that indicate the time period you would like to view.
2.5.4 Video Preview
Check the enable preview option to view the selected video.
2.5.5 Event Type
There are 6 event types; see Chapter 4 Guard for details. You may set up different colors for different event types to help you select events.
2.5.6 Time Table y
Utilize the icon to select all channels; also utilize the icon to deselect all channels. Finally, utilize the scale bar modify the scale of the time table. y
To pressure the button “Show Records” makes Time Table show the period of recording data like below:
Show
Records
to page45
Intelligent Surveillance Solution
2. Playback
y
To pressure the button “Show Event Log” makes Time Table show the time of event detection like below:
Show Event Log
2.5.7 To Withdraw the Record
Step 1: From the record display window at the top left of the Date Time
Panel, select the date you want to withdraw the record from. The red/green/blue lines shown on the time table indicate available recorded video records.
Note:
The record display window can be shown in (a) calendar view or (b) list control view. To modify the setting of the record display window, click
on the Setting button at the right of the Playback Console. See page 59
for more details.
Step 2: Use color bars to differentiate event types from each other. This will help you select video clips.
Step 3: Highlight the video clip you want to review by left-clicking and dragging the time period. You may also utilize the Start Time and
End Time in Date Time Period Section. In addition, modify the scale of the time table with the + and – signs on the bottom left. page46
Intelligent Surveillance Solution
2. Playback
Step 4: Check the Enable Preview option to get the preview of the video you select.
Step 5: Click the camera name to increase or decrease cameras you want to playback.
Step 6: Click OK when completing the setting.
2.6 Search Mode
Click on the Search Mode icon to obtain the Intelligent Search Tool panel.
You can setup unusual events here to detect abnormality occurred during the recoding period. y
Intelligent Search Tool Panel:
Click on the Search Mode icon and get the Intelligent Search Tool panel. Set up unusual events here to detect abnormality that occurred during the recording period.
y
5 events:
There are 5 types of unusual events: General Motion, Foreign
Object, Missing Object, Lose Focus, and Camera Occlusion.
2.6.1 Unusual Event-General Motion y
General Motion:
Detect all movements in the defined area. y
Define Detection Zone:
Left click and drag to draw a detection zone. You may define more than one zone on the screen by repeating the process. y
Sensitivity:
Modify the sensitivity setting by changing the slider control. Move toward right will increase the sensitivity level, which means a relatively small movement will trigger the alarm; in contrast, move the slider control toward left will reduce the sensitivity for movement detection.
Set up an appropriate sensitivity level reduces the frequency of false alarm. For instance, you can lower the sensitivity to avoid the alarm page47
Intelligent Surveillance Solution
2. Playback
being triggered by a swinging tree in the breeze. y
Interval:
Move the slider control to the right to increase time interval so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the time interval. y
Stop When Found:
Check the option to have the video stopped when detecting motion in the detection zone. Uncheck the option to have video kept rolling, and all detected events will show on the list in search result box. Click on the listed event in the box to jump to the point in the video where a motion is detected.
2.6.2 Unusual Event-Foreign Object y
Foreign Object:
Alarm is set off when any additional object appears in the defined area on the screen. y
Define detection zone:
Before detecting foreign object, it is required to define a detection area. In order to do so, left click and drag on the screen. Alarm will be triggered when any additional object appears in the detection zone. y
Define object size:
Drag and draw on the screen to define the size of a foreign object. y
Sensitivity:
Modify the sensitivity setting by changing the slider control.
Move toward right will increase the sensitivity level, which means a relatively small movement will trigger the alarm; in contrast, move the slider control toward left will reduce the sensitivity for movement detection. y
Interval:
Click and move the slider control to the right to increase time interval so that the alarm will only be triggered when the object has been removed from the area for longer. Move to the left to reduce the time interval.
Set up an appropriate Interval value will reduce the chance of false alarm. page48
Intelligent Surveillance Solution
2. Playback
For example, you can lower the Interval to avoid the alarm being triggered by a pedestrian.
2.6.3 Unusual Event-Missing Object y
Missing Object:
Alarm is set off when the selected object is removed from the defined area on the screen. y
Define detection zone:
Before detecting missing object, it is required to define a detection zone.
Left click and drag to draw a detection zone.
Alarm will be triggered when the defined object is removed from the detection zone. y
Sensitivity:
Modify the sensitivity setting by changing the slider control.
Move toward right will increase the sensitivity level and a relatively small movement will trigger the alarm; in contrast, move the slider control toward left will reduce the sensitivity for movement detection. y
Interval:
Click and move the slider control to the right to increase time interval so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the time interval.
2.6.4 Unusual Event- Focus Lost / Camera Occlusion y
Focus Lost:
System will inform you when the camera(s) lose its focus. y
Camera Occlusion:
Alarms when any of the cameras is blocked.
2.7 Enhancement
2.7.1 General Setting
Check the option and chose whether you want to apply the setting to all the channels or only to those currently shown on the screen.
2.7.2 Filter Setting y
Visibility:
Check the option and adjust the gamma value of the image to enhance the image and page49
Intelligent Surveillance Solution
2. Playback
make it cleaner. y
Sharpen:
Check the option to activate the function. Move the slider control to the right to sharpen the image, to the left to soften it. y
Brightness:
Check the option to activate the function. Move the slider control to the right to make the image brighter. y
Contrast:
Check the option to activate the function. Move the slider control to the right to increase contrast. y
Grey Scale:
Check the option to show the record in grey scale mode so the image displays in black and white.
2.8 Save Video
Step 1: Click on the display screen to choose the camera display that you want to save as a video clip.
Step 2: Set up the cue in and cue out points; the cue in and cue out time will show on the information window.
Cue In Cue Out
Step 3: Click Save Video icon, choose the folder where you want to save the file at, enter the file name and click SAVE.
Step 4: Set the Export Format as ASF or AVI
(ASF recommend) and set the Use Profile.
Step 5: Select to export (i.e. save) the record video with Audio, OSD and POS, or export video only. page50
Intelligent Surveillance Solution
2. Playback
Step 6: Click OK to save the video.
2.9 Save Image
Step 1: Click on the display screen to choose the camera display from which you want to save pictures.
Step 2: Click Save Image button when the image you want is shown on the screen. You may click Pause to freeze the video, use Step Forward/
Step Backward function to find the picture(s) that you want to save.
Step 3: Select OSD option and POS option to export the image with date/time, camera number/name and POS text. If the digital PTZ function is enabled in display view, you can also decide either Full size or Selected
region as your image region.
Step 4: You have the options to copy the image to clipboard or to save it. To save image just choose the folder and the format of image (BMP or JPEG) you prefer and then click save.
Note:
You may skip step 3 by pre-setting a folder and format that you want to save the images (refer the section Automatically save the image
2.10 Print
Print the current image of the video you choose.
Page Setting:
Set to print the image with original size or fit the page. Set Align image to Top, Center, or Bottom.
Print Content:
Print the image from currently selected channel or all the channels shown on the screen. page51
Intelligent Surveillance Solution
2. Playback
2.11 Backup
Different from Save Video, the Backup function saves everything from the
Playback panel, including log information.
You can start a full function Playback Console and load the backup files into it on any PC with Windows operating system. This means you may monitor the real time video and work on the backup files on separate computers simultaneously.
Step 1: Press the “Open Record” to select data and press “Backup”.
Step 2: You can adjust the Start Time and End Time you want to backup.
Step 3: You can adjust the Cameras you want to backup.
Step 4: You can calculate the size of the backup data.
Step 5: Select the directory you want to save the backup data including
CDROM, DVD or HardDisk.
Step 6: Check the log you want to backup.
Step 7: Press the “Backup” to start backing up.
Step 2
Step 3
Step 4
Step 6
Step 5
Step 7
page52
Intelligent Surveillance Solution
2. Playback
2.12 Log Viewer
2.12.1 Unusual Event
View the unusual event history that had been detected by the Smart
Guard System.
Step1
Step2
Step 3
Step 4
Step1: Choose the type of events you wish to view or select “All” from the drop-down menu to view all types of events. The types of Unusual Event include General Motion, Foreign Object, Missing Object, Focus Lost,
Camera occlusion, Signal Lost, Disk Space Exhausted, System Health
Unusual and Digital Input Triggered.
Step 2: Choose the camera channel you wish to view or select “All” for all the channels available.
Step 3: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 4: Click Search.
Note:
When working with a video record,
1. Log Viewer will search for Unusual Event in the video record in Date &
Time mode, start from the beginning to the end of the record, which is the default setting of the system.
2. 2. A link ( ) will appear right next to each event time. By clicking on the link, the video will jump to the point where the unusual event takes place. page53
Intelligent Surveillance Solution
2. Playback
2.12.2 System Log
Select Log Type form the drop-down menu. There are total 31 types of log types, including:
1. Main Console Startup
2. Main Console Shutdown
3. User Login
4. User Login Failed
5. Start Schedule
6. Stop Schedule
7. Execute Recycle
8. Enable Channel
9. Disable Channel
10. Start Smart Guard
11. Stop Smart Guard
12. Modify Smart Guard
13. Modify Schedule
14. Modify Configuration
15. Start Live Streaming Server
16. Stop Live Streaming Server
17. Modify Live Streaming Server
18. Start Remote Playback Server
19. Stop Remote Playback Server
20. Modify Remote Playback Server
21. IP Camera Connection Lost
22. Auto Restart Windows
23. Modify POS Setting
24. POS Connection Lost
25. Modify E-Map
26. Start Remote Desktop
27. Stop Remote Desktop
28. Modify Remote Desktop
29. Start Central Management
30. Stop Central Management
31. Modify Central Management
Step 1
Step 2
Step 3
Step1: Choose the type of event you want to check or select “All” from the drop-down menu for all types of events.
Step 2: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search. page54
Intelligent Surveillance Solution
2. Playback
2.12.3 Counting Application
Display the history of Counting Application during a given time period.
Step 4
Step1: Select the channel you want to check or select “All” from the drop-down menu for all channels.
Step 2: Select search period. View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search.
Step 4: Press the button “Export to”.
Step 5: Type the file name and choose the file format (.xls or .txt).
2.12.4 Counting Application (Diagram)
Display the Counting Application data in diagram format.
Step 4
page55
Intelligent Surveillance Solution
2. Playback
Step1: Select the channel you want to check or select “All” from the drop-down menu for all channels.
Step 2: From the drop-down menu, set up how you would like the diagram to be displayed. You have the options of one day, one month, or one year.
Step 3: Select a specific date to make it the start point of the diagram.
Step 4: Click Search.
Step 5: Press the button “Export to”.
Step 6: Type the file name and the file will save as BMP files.
2.12.5 POS Log
View the POS Log history that had been detected by the Smart Guard
System.
Step 5
Step1: Choose the type of events you wish to view or select “All” from the drop-down menu to view all types of events. The types of Unusual Event include Transaction Start, Transaction End, Open Cash Register,
Connection Lost, and special User defined event. Please refer the User manual of POS for detail.
Step 2: Choose the camera channel you wish to view or select “All” for all the channels available.
Step 3: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time. page56
Intelligent Surveillance Solution
2. Playback
Step 4: Click Search.
Step 5: Press the button “Export to”.
Step 6: Type the file name and choose the file format (.xls or .txt).
2.12.6 Export and Backup Log
View the Export and Backup Log history that had been operated by local
or remote user.
Step1: Choose the type of event you want to check or select “All” from the drop-down menu for all types of events.
Step 2: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search page57
Intelligent Surveillance Solution
2. Playback
2.12.7 Export
After search the log you want, just export it to .xls or .txt file.
Step 1
Step1: Press the button “Export to”.
Step2: Type the file name and choose the file format (.xls or .txt).
.xls
.txt
page58
Intelligent Surveillance Solution
2. Playback
2.13 Setting
2.13.1 Record Display
Calendar View:
Make the record display windows as calendar view.
List Control:
Make the record display windows as list control.
2.13.2 Play y
Play when open:
Check the option and set the system to start playing the video clip every time when a record is withdrew. y
Auto skip when record motion only mode:
Check the option to set up the system to automatically skip to the points where there were motions recorded. y
Next interval:
Set the interval with which the video goes forward when you click on the Next icon on the control panel. y
Previous interval:
Set the interval with which the video goes backward when you click on the Previous icon on the control panel.
2.13.3 Capture Image: Setup how you want to save image. y
Save in clipboard:
The image will be saved in the clipboard and can be pasted on other application software. y
Manually save the image file:
You can manually select where you want to save the image, name the saved file, and choose the format you want to save the image. y
Automatically save the image file:
By pre-setting a path/URL and the image format, the system will automatically save the image accordingly when you click the Save button in the control panel. page59
Intelligent Surveillance Solution
2. Playback
2.13.4 Miscellaneous y
Synchronize video frames:
Select it to avoid the tearing problem occurring in video display while increasing the CPU loading.
2.13.5 OSD Setting
Enable Camera OSD to display video information on recording video, information includes camera name, camera number, date and time.
User also can set up OSD font; include the font, size, font color and any font effects desired.
2.13.6 POS Overlay Setting
Enable POS overlay to adjust Font, Size, Color, Bold, Edge in Foreground section, color and Transparency in Background section, and then adjust display settings in Display on Video Preview.
2.14 Remote Server
page60
Intelligent Surveillance Solution
2. Playback
2.14.1 Add Remote Playback Site
Press the “Remote Sever ” can go to remote playback site management to add and setup the remote playback site.
Step 1: Enter the IP address or
DNS, Port, Username, and Password.
Step 2: Click “Add” to add the server.
Step 3: Click OK to exit the Setting panel.
2.14.2 Access Remote Playback Site
Go to Date Time Panel and click on the icon on the top of the display window to access the Remote Playback Site page61
Intelligent Surveillance Solution
3. Schedule
3. Schedule
Click on the Schedule icon on the Main Console and set up the time duration for video recording on the schedule configuration panel. page62
Intelligent Surveillance Solution
3. Schedule
3.1 Day Mode
Schedule the cameras to turn the recorder on and off at the same time every day according to your setting.
Load
Camera /
Channel
Day Mode
To setup the time schedule for each camera, you may
1. Load the preset modes or
2. Insert a new schedule manually or
3. Copy to other cameras after manually setup.
3.1.1 Load Preset Modes
The system provides six modes to quickly setup recording schedule. Simply click on the “ Load” for the drop-down menu to setup.
Refer below tables for the definitions of each mode in each series.
IP+ series (IP camera)
Mode Format Time Record FPS Quality Resolution
Regular
MPEG-4 Max
Office
MPEG-4 Max
Shop
MPEG-4 Max
Highly Secure
MPEG-4 Max
Disk Saving
MPEG-4
Minor
MPEG-4
*The ”Max” means as the same settings as “camera settings” in the page63
Intelligent Surveillance Solution
3. Schedule
config/setting/camera/camera Parameter panel.
SCB-1000, SCB-2000, SCB-3000, SCB-4000 series (Analog camera)
Mode Format Time Record FPS Quality Resolution
Highly Secure MPEG-4 0:00-24:00
Disk Saving MPEG-4 0:00-24:00
Always 30 Normal CIF
Always 30 Highest Max
Motion 30 Normal CIF
SCB-5000 series (Analog camera)
Mode Format Time Record FPS Quality Resolution
Highly Secure
Disk Saving
H.264
H.264
0:00-24:00
0:00-24:00
Always 30 Normal CIF
Always 30 Highest DCIF
Motion 30 Normal CIF
SCB-7000 series (Analog camera)
Mode Format Time Record FPS Quality Resolution
Highly Secure
Disk Saving
H.264
H.264
0:00-24:00
0:00-24:00
Always 30 Normal D1
Always 30 Highest D1
Motion 30 Normal CIF page64
Intelligent Surveillance Solution
3. Schedule
3.1.2 Insert a New Schedule Manually
Step 1: Left-click and draw the bar you want add to the time table. The scheduled time will show as a grey bar.
Step 1
Step 2 Step 3 Step 4
Step 2: Click the Insert icon and add a new schedule in the Regular
Mode, i.e. to record video during the time period you set with 30 FPS,
Normal video quality, and Normal resolution.
Step 3: Change the setting if wished by clicking on the Configure icon
(See 3.7 Encoding Option Panel) or double click the schedule
information.
Step 4: Click OK.
3.1.3 Copy Schedule
You may set up the schedule for each channel/camera by repeating the process above, or simply apply the setting of a single camera to all the others by click the Copy to icon on the top of the display window. page65
Intelligent Surveillance Solution
3. Schedule
3.2 Week Mode
Schedule the cameras for each day of the week differently. In addition, you may assign extra holidays under the Week Mode.
Custom
Holiday
Default
Week Mode
3.2.1 Default
Follow the same process to setup the schedule for every day in a week.
3.2.2 Holiday
You may assign holidays where the system will work according to the setting of Sunday.
3.2.3 Custom
You can assign a particular date(s) on which the system will work according to a special schedule(s) different from the others. page66
Intelligent Surveillance Solution
3. Schedule
3.3 Adjust the Scheduled Setting:
You can manually change the setting at any time after you insert or load a period of schedule. y
Option 1: Move the cursor to the
Time Bar
and change the length or move the bar sideway to change the start and end points. y
Option 2: Click on the Configure icon or double click on schedule information on the screen (highlighted in blue) to obtain the Encoding
Option panel (next page) and change the setting as wished.
Time Bar
Configure
Schedule
Information
page67
Intelligent Surveillance Solution
3. Schedule
3.4 Encoding Option
Original Video Encoded Video
Time Option Record Mode Video Encoder
3.4.1 Pre-record/ Post-record Time
The pre-record/ post-record function saves the recording data accordingly. For instance, to set up a
5 second pre-record time means the system will start saving the recording data 5 seconds before the event happens.
Note:
The maximum of pre-record/post record period is 60 seconds.
3.4.2 Record Mode
Always Record
:
Select this option to record the video continuously.
Record on Event
:
Select this option to obtain the Select Event panel. page68
Intelligent Surveillance Solution
3. Schedule
From the Smart Guard list, check the box of the camera events or digital inputs to trigger the recording action. Click OK to complete the setting.
Note:
A prerequisite to trigger the recording schedule of camera/DI/POS event is to enable Smart Guard function in MainConsole start panel first.
Record on Motion:
Select this option to start recording when motions are detected. Please adjust sensitivity, the frame interval and setup detection zone to detect
Motion. To setup single detection zone, left-click and drag the mouse to draw a rectangle. To setup more than one detection zones, simply repeat the same process. Or just click “All” to select the entire detection zone.
Note:
The rectangle number cannot exceed 10.
3.4.3 Encoded Options
This option is to setup quality of recording video. Original Video window is the original stream form camera, and Encoded Video window is preview of the recording video correspond with the encode settings of below.
For IP camera
The Encode Video function will drop frame or re-encoded original streaming form IP cameras. To save Hard Disk usage, adjust FPS with original video format or re-encode to small size by adjust FPS, resolution and Quality/Bitrate.
Keep Original Video format:
Select this option to drop down frame rate only but not to re-encode video stream to save Hard
Disk usage.
- Adjust MJPEG video frame rate: Leftward indicator slider to reduce frame rate.
Note:
The maximum FPS will be correspond with original video stream set up on camera configuration.
- Keep key-frame only: System will only record key frames of video streaming.
Note:
The key frame interval is controlled by each camera manufacturer and can’t be adjusted with system.
Customized encoding:
The video stream would be decoded then page69
Intelligent Surveillance Solution
3. Schedule
re-encoded by configuration. Click Setup button to adjust Encoder
parameter.
Note:
1. There is only one adjustable option of Quality and Bit rate at one time.
2. Customized encoding function will lead into high CPU usage, please make sure the PC specification is enough (recommend
Core 2 Quad)
For Analog camera
The Encode Video function could setup Frame Rate,
Quality, and resolution which want to record and provide an approximated recorded period.
Note:
The capture devices “SCB series” required. page70
Intelligent Surveillance Solution
4. Guard
4. Guard
Click on the Guard button on the Main Console to start the Event and
Action Configuration panel. You need to specify an event to be detected as well as to set up an action with which the system will take when the specified event is detected.
Note:
y
Crystal Ball: Indicates the working status of the system, in blue color rolling when system is recording; in red when an event is detected. y
Event Report: When the crystal ball is red, you can click it to obtain the Smart
Guard Event Report than cancel the event(s). page71
Intelligent Surveillance Solution
4. Guard
4.1 Event
Insert Event
There are 4 sources of events: Camera (video image), POS, Digital Input
(device connected to your PC) and System (condition of your hardware).
You can assign multiple events by following the instructions below.
4.1.1 Camera Event - Assign a Camera Event
Step 1: Select a channel from the camera list and click the Insert Event icon. .
Step 2
Step 3
Step 2: There are six types of events: Signal Lost, General Motion, Foreign
Object, Missing Object, Lose Focus, and Camera Occlusion. Select the event you want on the Event Type list, and then click OK.
Step 3: Configure the setting of the Event Type. See the following instructions.
4.1.2 Camera Event – Basic Setting of camera event
-Basic setting of vide Signal Lost, General Motion, Foreign Object,
Missing Object, Focus Lost, and Camera Occlusion events.
page72
Intelligent Surveillance Solution
4. Guard
Enable Event:
Check the box to activate the event.
Life Cycle:
y
Automatically cancel event when event disappears: the alarm/action will be cancelled once the abnormality is fixed or ends. y
Manually cancel event or event continues triggered: The alarm/action will continue until being canceled from the Main Console. The user currently not at the seat watching the screen will be notified by the alarm.
Note:
To cancel the event:
1. Start>Open Event Report>Cancel
All Events
2. Click the red crystal ball to obtain the Smart Guard Event Report than cancel the event(s). y
Cancel event after timeout xx seconds:
Enable checkbox and setup the timeout seconds to cancel the event after the time that you set whatever the events disappear or not.
4.1.3 Camera Event - Signal Lost
- Detect the loss of video signal from camera.
4.1.4 Camera Event - General Motion
- Detect any movement in the defined detection zone.
Sensitivity
Interval
Region Definition
Start Simulation
page73
Intelligent Surveillance Solution
4. Guard
Alarm Event Option:
y
Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm.
Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze. y
Interval: Click and move the slider control to the right to increase interval time so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the interval time.
Region Definition:
y
Define detection zone: To detect General Motion, you have to define a detection zone. Left-click and drag the mouse to draw a detection zone. You may define more than one zone on the screen by repeating the same process. User can also click on “All” button to select the entire detection zone.
Start Simulation:
Click the Start Simulation button and test the function on the preview screen.
4.1.5 Camera Event - Foreign Object
- Alarm will be set off when an object appears in the defined area on
the screen.
Sensitivity
Interval
Region Definition
Define object size
Start Simulation
page74
Intelligent Surveillance Solution
4. Guard
Alarm Event Option:
y
Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm.
Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze. y
Interval: Click and move the slider control to the right to increase interval time so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the interval time.
Region Definition:
y
Define detection zone: To detect General Motion, you have to define a detection zone. Left-click and drag the mouse to draw a detection zone. You may define more than one zone on the screen by repeating the same process. User can also click on “All” button to select the entire detection zone. y
Define Object size: After defining the detection zone, select Define
object size and then left-click and drag the mouse to indicate the size of the object you want to detect.
Hint:
For instance, if you want to prevent somebody from leaving a briefcase in a hallway, you may put a briefcase in the hallway where the camera is aiming. On the screen of the camera, draw an area that fits the size of the briefcase and define it as the object size, and then remove the briefcase before activating the Smart Guard function on the Main
Console. The system will consider everything in the screen normal when you click Start to activate the monitor function.
Start Simulation:
Click the Start Simulation button and test the function on the preview screen.
4.1.6 Camera Event - Missing Object
- Alarm will be set off when an object disappears in the defined
area on the screen.
page75
Intelligent Surveillance Solution
4. Guard
Sensitivity
Interval
Region Definition
Start Simulation
Alarm Event Option:
y
Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm.
Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze. y
Interval: Click and move the slider control to the right to increase interval time so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the interval time.
Region Definition:
y
Define detection zone: To detect General Motion, you have to define a detection zone. Left-click and drag the mouse to draw a detection zone. You may define more than one zone on the screen by repeating the same process. User can also click on “All” button to select the entire detection zone.
Hint:
For instance, if you want to prevent somebody from removing the computer monitor on the desk, draw an area that fits the size of the monitor on the screen. page76
Intelligent Surveillance Solution
4. Guard
Start Simulation:
Click the Start Simulation button and test the function on the preview screen.
4.1.7 Camera Event - Lose Focus
- This function alarms you when any of the cameras is losing focus
and has blur image.
Sensitivity
Interval
Ignore Lighting
Start Simulation
Alarm Event Option:
y
Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm.
Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze. page77
Intelligent Surveillance Solution
4. Guard
y
Interval: Click and move the slider control to the right to increase interval time so that the alarm will only be triggered when the movement lasts longer. Move to the left to reduce the interval time. y
Ignore Lighting: Check the box to avoid alarm being set off by light changing.
Region Definition:
y
Define detection zone: To detect General Motion, you have to define a detection zone. Left-click and drag the mouse to draw a detection zone. You may define more than one zone on the screen by repeating the same process. User can also click on “All” button to select the entire detection zone.
Start Simulation:
Click the Start Simulation button and test the function on the preview screen.
4.1.8 Camera Event - Camera Occlusion
- This function alarms you when any of the cameras is blocked.
Sensitivity
Interval
Ignore Lighting
Start Simulation
Alarm Event Option:
y
Sensitivity: Click and move the slider control to the right to increase sensitivity so that a relatively small movement will trigger the alarm.
Move the bar to the left to reduce the sensitivity of movement detection. Set up an appropriate Sensitivity value will reduce the chance of false alarm. For example, you can lower the Sensitivity to avoid the alarm being triggered by a swinging tree in the breeze. y
Interval: Click and move the slider control to the right to increase interval time so that the alarm will only be triggered when the page78
Intelligent Surveillance Solution
4. Guard
movement lasts longer. Move to the left to reduce the interval time. y
Ignore Lighting: Check the box to avoid alarm being set off by light changing.
Region Definition:
y
Define detection zone: To detect General Motion, you have to define a detection zone. Left-click and drag the mouse to draw a detection zone. You may define more than one zone on the screen by repeating the same process. User can also click on “All” button to select the entire detection zone.
Start Simulation:
Click the Start Simulation button and test the function on the preview screen.
4.1.9 POS Event - Assign a POS Event
Step 1: Select a POS device from the list and click to insert event.
Hint:
You should insert the POS device in Config>POS Application first, then you could set the alarm base on it.
Step 2: There are five types of events:
Transaction Start, Transaction End,
Open Cash Register, Connection Lost and User Defined. Select the event you want on the Event Type list, and then click OK.
Transaction Start - Detect any transaction beginning.
Transaction End - Detect any transaction ending.
Open Cash Drawer - Detect any cash drawer opening.
Connection Lost - Detect the connection abnormal event between
POS box and Main Console system.
User Defined - Detect any condition which is defined by user. Click the User Defined number to customize the alarm rule. page79
Intelligent Surveillance Solution
4. Guard
Step 3: Configure the setting of the Event Type. Please refer the User manual of POS for detail.
4.1.10 Digital Input Event - Digital Input Event
Step 1
Step 2
Step 1:
Click and highlight Digital Input on the event type list, and then click the Insert Event icon.
Step 2:
Select the device that is connected to your system, that is, the PC you are working with. page80
Intelligent Surveillance Solution
4. Guard
4.1.11 System Event - Assign a System Event
Step 1
Step 2
Step 1:
Click and highlight System on the event type list, and click the
Insert Event icon.
Step 2:
There are Four events. Select the event you want to detect.
4.1.12 System Event – Basic Setting
- Basic Setting of Disk Space Exh austed, System Health Unusual,
Resource Depleted, and Network Congestion events.
Enable Event:
Check the box to activate the event.
Life Cycle:
y
Automatically cancel event when event disappears: the alarm/action will be cancelled once the abnormality is fixed or ends. y
Manually cancel event or event continues triggered: The alarm/action will continue until being canceled from the Main
Console. The user currently not at the seat watching the screen will be notified by the alarm.
Hint:
To cancel the event:
3. Start>Open Event Report>Cancel All Events
4. Click the red crystal ball to obtain the Smart Guard Event Report than cancel the event(s). y
Cancel event after timeout xx seconds: Enable checkbox and setup the timeout seconds to cancel the event after the time that you set page81
whatever the events disappear or not.
Intelligent Surveillance Solution
4. Guard
Activated Period:
y
Always activated: Select the option to enable event when Main
Console is running (Make sure the smart guard system is enabled in start panel). y
Activated only in the following period: You can set up the system to react during a certain time period; for example, office hours.
4.1.13 System Event - Disk Space Exhausted
- This function alarms you when disk space is exhausted.
4.1.14 System Event - System Health Unusual
- This function alarms you when high
CPU temperature or low fan speed.
Current Status:
Show you the current CPU temperature, Motherboard Temperature,
Fan Speed and Power fan speed.
Options:
Check the Temperature Format
Celsius or Fahrenheit, adjust the High
(Motherboard) Temperature Alarm at what temperature degrees and Low (Power)Fan
Speed Alarm at what RPM(revolutions per minute).
4.1.15 System Event – Resource Depleted
- This function alarms you when CPU or
memory is depleted.
Current Status:
Show you the current Total
CPU Loading and Total Memory Usage.
Options:
Check the High CPU Loading
Alarm and High Memory Usage Alarm at what Percentage. page82
Intelligent Surveillance Solution
4. Guard
4.1.16 System Event – Network
Congestion
- This function alarms you when
network bandwidth is overloading.
Current Status:
Show you the current
Total Upload Bitrate and Total
Download Bitrate.
Options:
Check the High Upload
Bitrate Alarm and High Download
Bitrate Alarm at what Kbps (kilobits per second). page83
Intelligent Surveillance Solution
4. Guard
4.2 Action
4.2.1 Action - Assign a action type
Insert Action:
To setup actions responding to an unusual event.
Step 1
Step 2
Step 1: Choose an event and click the “Insert Action” icon.
Step 2: There are 10 types of actions, Select the action you want on list and then click OK.
1. On Screen Display
2. Play Sound
3. Send E-mail
4. Phone Call
5. PTZ Preset Go
6. DI/DO
7. Send a SMS Message
8. Send to Central Server
9. Send snapshot to FTP
10. Popup E-Map on event.
Step 3: Configure the setting of the Action Type if needed. page84
Intelligent Surveillance Solution
4. Guard
4.2.2 Action Type - On Screen display
- A red warning will be flashing on the screen of Main Console,
indicating which type of unusual event is detected.
Step 1: Select the “On Screen display” action and then click OK.
Step 2: The responding window will popup to Selected Camera. Click the
“On Screen display” indicator to modify the setting.
Camera:
Display the camera applied to this action.
Auto popup:
Click the Auto popup column and select the expected monitor for popping up the event.
Displayed text:
You can follow the default setting to show the event type, or enable “Customized Text” to define the text as your preference.
4.2.3 Action Type - Play Sound
- Sound alarm warning. The system will play the sound as alarm when
an unusual event is detected.
Step 1: Select the “Play Sound” action and then click OK.
Step 2: The responding window will popup to Choose a Wave
file (.wav) from. Click the “Play
Sound” indicator to modify the setting. page85
Intelligent Surveillance Solution
4. Guard
4.2.4 Action Type - Send E-mail
- The system will send an E-mail immediately to given accounts
indicating the type of event, the time, and attaching a picture taken while the event is detected.
Step 1: Select the “Send E-mail” action and then click OK.
Step 2: The responding window will popup to Select Contactor (You can choose one more contacts at once). Click the “Send E-mail” indicator to modify the setting.
Edit Address Book:
You can insert the contact information at this panel.
Note:
To give the system the E-mail accounts, go to Config > Setup >
Hotline. See Configuration at page 105 for detail.
page86
Intelligent Surveillance Solution
4. Guard
4.2.5 Action Type - Phone Call
- The system will call a given phone number when an unusual event is
detected.
Step 1: Select the “Phone Call” action and then click OK.
Step 2: The responding window will popup to Select Contactor (You can choose only one contact at once).
Click the “Phone Call” indicator to modify the setting.
Edit Address Book:
You can insert the contact information at this panel.
The panel is the same as the one in “Send E-mail” action.
Note:
To setup the phone number and make an audio record for the
phone call, go to Config > Setup > Hotline. See Configuration at page 105
for detail.
4.2.6 Action Type - PTZ Preset Go
- The PTZ (pan/tilt/zoom) camera will go to a preset point or auto
patrol when an unusual event is detected.
Step 1: Select the “PTZ Preset Go” action and then click OK.
1.
2.
Step 2: The responding window will popup to PTZ Camera Preset Go.
Click the “PTZ Preset Go” indicator to modify the setting.
Step 3: Set the action of cameras which you want to trigger by events.
For example:
Please follow below steps to setup this function.
y
Set the action of camera 1:
1. Choose camera 1.
3.
2.
page87
Intelligent Surveillance Solution
4. Guard
2. Set the start, end preset points.
3. Select the Life Cycle.
4. Click on Add. y
Set the action of camera 2:
5. Choose camera 2.
6. Set the start patrol and end patrol.
7. Select the Life cycle
8. Click on Add.
9. Finally click on Ok to save all setting of cameras.
Note:
Configure your PTZ camera before using this function. See
Config at page 103 for PTZ camera configuration.
4.2.7 Action Type – DI/DO
- To trigger Digital input/output devices
those connect to the system, such as alarm lights and sirens.
Step 1: Select the “DI/DO” action and then click OK.
Step 2: The responding window will prompt user to Select Digital Input Module. Click the
“DI/DO” indicator to modify the setting.
Step 3: Select the device that is connected to your system, that is, the PC you are working with. You can enable the Automatically popup I/O
control panel check box to obtain the correspondent panel to monitor the I/O status.
Hint:
You should adjust the setting of I/O device in Config>Setting>I/O Device first, the
I/O control panel will display the device status based on it. You can also adjust the size of the panel by dragging a mouse or click the on the right top of the display window. page88
Intelligent Surveillance Solution
4. Guard
4.2.8 Action Type –Send a SMS message
- The system will send a SMS message immediately to given
accounts indicating the type of event, the time.
Step 1: Select the “Send a SMS message” action and then click OK.
Step 2: The responding window will popup to Select Contactor (You can choose one more contact at once).
Click the “Send a SMS message” indicator to modify the setting.
Edit Address Book:
You can insert the contact information at this panel. The panel is the same as the one in “Send
E-mail” and “Phone Call” action.
Note:
To give the system the GSM modem, go to Config > Setup > Hotline.
See Configuration at page 105 for detail.
4.2.9 Action Type – Send to Central Server
- The system will send a Event to Central Server.
Step 1: Select the “Send to Central Server” action and then click OK.
Note:
The detail please refers the user manual of Central Management
System.
4.2.10 Action Type – Send snapshot to FTP
- The system will upload a snapshot immediately to FTP site.
Step 1: Select the “Send snapshot to FTP” action and then click OK.
Note:
To give the system the FTP server, go to Config > Setup > Hotline.
See Configuration at page 105 for detail.
page89
Intelligent Surveillance Solution
4. Guard
4.2.11 Action Type – Popup E-Map on Event
- The system will auto popup E-Map window and show the assigned
map and indicator.
Step 1: Select the “Popup E-Map on Event” action and then click OK.
Step 2: The responding window will popup to Popup e-map on event. Click the
“Popup E-Map on Event” indicator to modify the setting.
Step 3: Select the Map Layer and Indicator, and then click OK.
Note:
To edit E-Map, see Configuration at page 127 for detail.
page90
Intelligent Surveillance Solution
5. Configuration
5. Configuration
Click on the Config icon, select from the drop-down menu and open the
Configuration panel. Modify the setting and access License Manager, Counting application, POS application, Log viewer,
Backup, Network Services. Select
Save/Load Configuration to save/load all the settings.
* Video Source function available only with
MPEG-4 software compression captures devices.
Config
page91
Intelligent Surveillance Solution
5. Configuration
5.1 Setting – General
Startup
Storage
Status Display
Miscellaneous
5.1.1 Startup
Audio Preview Auto Reboot
Check the MainConsole box to execute Main Console system when windows startup.
Check the following 3 main functions and 5 network services to auto activate functions when Main Console system is executing, including
Schedule Recording System, Smart Guard System, Counting Application,
Live Streaming Server, Remote Desktop Server, 3GPP Server, Remote
Desktop Server and Central Management Service.
Check the other options also can setup the startup status as Full screen or allow system to auto login with the preset account.
Setup Auto login: Enable “Auto login” and click the Setup button to obtain the Auto
Login Setup panel, insert the User Account and Password to login automatically when the system starts. Enable the Minimize after
login to minimize the MainConsole window after login. page92
Intelligent Surveillance Solution
5. Configuration
5.1.2 Storage
Location:
Assign the default folder (you can setup several directories for storage) for the system to store all data files. Recommend not to save in system HD (C:\) to avoid PC efficiency drop when free storage is low.
Automatic Recycle:
The system will automatically delete out-dated data to save storage space. y
Recycle when disk space is: Set the standard limit to let the system recycle automatically.
- Less than__MB: The system will start to recycle if the disk space is less than the indicated number.
Note:
1. The system will detect the storage space of default location firstly, if the default storage space is exhausted, the video will be stored to the next directory.
2. If all the status of locations exceeds the storage rule, the system will start recycling in an hour progress. y
Only keep video for: Delete the video records that are older than the number of days set.
Note:
1. If the default storage spaces exhausted (disc space is less than
1200MB), the system will start to recycle by hourly period. y
Log Recycling: Click the button to obtain the Advanced Recycle Setting panel. Set the days that you want to keep the event or Keep all event logs within interval of video files.
1. Event Log: Delete the event log data that is older than the number of days set.
2. System Log: Delete the system log data that is older than the number of days set.
3. Counting: Delete the counting application data that is older than the number of days set. page93
Intelligent Surveillance Solution
5. Configuration
4. POS Transaction: Delete the POS transaction data that is older than the number of days set.
5. Resource Report: Delete the Resource report data that is older than the number of days set.
5.1.3 Status Display
Check the boxes of the information that you wish to see in the information display window in the Main Console. y
Status Display: Select the information like Current Date, Current Time, Free
Disk Space, IP Camera Bitrate and User
Defined Text. y
Advanced Setting: Click the button to obtain the Advanced Setting Panel to select Temperature, Fan Speed, System
Resource and Network Utilization information you wish to display.
5.1.4 Miscellaneous
Automatically Popup Event Report
:
Event report dialog automatically popup when events been detected. Make sure to stop Smart Guard
System before you modify the setting, otherwise the modification will not take place. page94
Intelligent Surveillance Solution
5. Configuration
Minimize to system tray
:
Enable the Option to minimize the Main console to be an icon in notification area of windows task bar when pressing the minimize button.
Minimize
Note:
Insert the username and password of MainConsole again when clicking the minimized MainConsole icon in notification area of windows task bar to start monitoring.
Synchronize video frames: Select it to avoid the tearing problem occurring in video display while increasing the CPU loading. y
DDNS Service: Dynamic Domain Name
Server (DDNS) function allows you to use
Live View or Web View to connect to the Main Console through Internet event if you have a dynamic IP address.
Click on the DDNS button to obtain the
Dynamic DNS Setup panel. Set up the
DDNS function by selecting the provider type, filling with user name, password and hostname, and adjusting the update period.
5.1.5 Audio Preview
Default Channel:
Select the audio channel that you wish to hear from in
“Default Channel”.
Enable Audio on Active Channel:
Select the “Enable Audio on Active
Channel” option to hear the audio from selected video channel
(selected by mouse) on each video grid of Main Console. The default channel plays if the video channel isn’t selected.
Volume:
Adjust the volume with the “volume bar.” page95
Intelligent Surveillance Solution
5. Configuration
System plays the audio of
“default channel”
5.1.6 Auto Reboot
System plays the audio of left-top
“selected channel”
Check the option of “ Enable Auto Reboot ” that you can reboot the system on the time you select.
Step 1: Check the option of “ Enable Auto Reboot. ”
Step 2: Select the time you want to reboot.
Note:
Please also enable “Main Console”, “Auto Login”, “Setup login account” and check other status in Startup section when PC rebooting to ensure all system running normally after Auto Reboot.
page96
Intelligent Surveillance Solution
5. Configuration
5.2 Setting - Camera
Config
Search
Insert
Config
Delete
5.2.1 Add Camera
Four function buttons will be included in the Setting/Camera panel if you have our Hybrid Surveillance System license for IP camera.
Search:
Click on the Search icon to obtain the Search IP Camera panel.
The system will start scanning automatically once the panel is opened; feel free to stop scanning by clicking on the Stop Scan button.
Fill in the user name and password for each IP camera found and click OK to add it to the camera list.
Insert:
Click on the Insert icon to obtain the IP/Video Server Setting panel and add IP cameras to the list. See following part(IP Camera / Video
Server Setting panel) for detail. page97
Intelligent Surveillance Solution
5. Configuration
Delete:
Click on the Delete button to remove the selected IP camera(s) from the system. Click OK to finalize the modification.
Config:
Click on the Config button to obtain the IP/Video Server Setting panel. You can modify the IP camera settings with the Setting panel. See following part(IP Camera / Video Server Setting panel) for detail.
5.2.2 IP Camera / Video Server Setting panel
Network
Device
Description
Network:
Fill up the Network field (including Name, IP Address, Http Port,
User Name, Password and Protocol) referring to the instruction provided by the camera manufacturer. Check “Use DNS” to use domain name instead of IP address.
Device:
Choose the IP camera manufacturer from the drop-down menu.
Click on “Auto Detect” and the model name will show in the box.
Description:
Show information of the IP camera. page98
Intelligent Surveillance Solution
5. Configuration
5.2.3 Camera Parameter
Camera List
Camera Name
Go to Web Interface Camera Settings Video Parameter Stream Profile
Camera List:
The camera(s) connected to the system will show on the panel, click the name of the camera to adjust the setting.
Camera Name:
Name the camera for your convenience.
Go to Web Interface:
Go to Website interface to configure the camera setting (option).
Camera Settings:
Set the camera parameter offered by camera vendor.
Video Parameter:
Adjusts the video’s brightness, contrast, saturation, and color hue values.
Stream Profile:
Stream profiles are pre-defined the prefer settings which will response the query form remote live view function. Each profile has different Format,
Frame, Resolution, Quality and Bitrate(Kbps) settings. page99
Intelligent Surveillance Solution
5. Configuration
Stream Profile
Options
Note:
The types of stream profile and options will different with stream sources. z
IP camera: z
5 profiles with Original (only can drop frame rate), High, Normal, Low and Minimum (for PDA/Smart Phone Client).
Analog camera with SCB-1000-4000s:
4 profiles with High, Normal, Low and Minimum (for PDA/Smart Phone z
Client).
Analog camera with SCB-5000s:
3 profiles with Normal (H.264 format only), Low and Minimum (for z
PDA/Smart Phone Client).
Analog camera with SCB-7000s:
4 profiles with H.264 (H.264 format only), High, Normal, Low and
Minimum (for PDA/Smart Phone Client).
Note:
1. Use Copy to option could apply the setting of a single camera to all the others.
2. To choose stream profile of remote live view, see Live view setting at
page100
Intelligent Surveillance Solution
5. Configuration
5.2.4 OSD Setting
Select the information that you wish to see in the on-screen display, or the sub-screen of the camera. And then, click the Font button to setup the font style. page101
Intelligent Surveillance Solution
5. Configuration
5.3 Setting - I/O Device
I/O Device Setting
List of devices
Device Setting
Input Monitor
Output Monitor
I/O Device Setting:
y
Module Setting: Name the module device and ID that has been connecting the digital input/output device(s) to your system. y
Device: This column displays the device(s) already installed to the system. y
ID: Select the number of the I/O port to which you plug the ribbon cable.
Input Monitor:
The device(s) is turned on if the dot is in red. By triggering the digital input device, the related icon will light up. This is used to check if the device is correctly connected or not.
Output Monitor:
The device(s) is turned on if the dot is in red. By clicking on the icon, you may trigger the digital device connecting to the system. This can be used to test if the output device is correctly connected.
Device Setting
y
Name: Insert the name of the device (input and output). y
Type: Select the device type from the drop-down menu.
1. N/O: Normal Open.
2. N/C: Normal Close. page102
Intelligent Surveillance Solution
5. Configuration
5.4 Setting - PTZ Config
Basic Setting
Advanced Setting
Miscellaneous
Install PTZ cameras and follow the instruction of the camera manufacturers. A PTZ camera is usually connected to the PC with
RS-485/RS-422.
Check the box on the camera list to activate the PTZ control function of a
PTZ camera.
Basic Setting:
Select the camera model, com port, baud rate, and address according to your PTZ camera.
Note:
If the camera model is IP camera, you can work PTZ function directly without the com port, baud rate, and address settings.
Advanced Setting:
You may setup the pan speed, tilt speed, zoom speed and auto pan speed. Adjust the settings by dragging the bars.
Miscellaneous:
y
Patrol Group:
You can setup the Patrol Group, please see page 37 for
the detail. page103
Intelligent Surveillance Solution
5. Configuration
y
User-Define Preset: User-Define Preset for analog speed dome can trigger the extra-function of speed dome itself such as auto-tracking, login menu of camera…etc. You can refer the detail description of each analog speed dome on it’s user manual.
Step 1: Type the Preset Name.
Step 2: Type the Preset Number.
Step 3: Pressure the buttons to Add,
Delete, or Update preset setup. page104
Intelligent Surveillance Solution
5. Configuration
5.5 Setting – Hotline
Configure the settings of hotlines, including E-mail, FTP, GSM modem and
Telephone calls, once an unusual event is detected.
E-mail:
Input the following information: Server, Port, Sender’s E-mail address, E-mail’s subject title, Body content and SSL option for encrypted transmission. Click on the Send Test Mail button to test the settings.
Note:
* indicates mandatory areas
FTP:
Input the following information: server, Port, Login ID, Password, and
Upload directory. According your FTP type to enable/disable Passive mode. You may click on the Upload Test File button to test the settings.
Note:
* indicates mandatory areas
Telephone:
Select the modem that the system is going to dial the info call with, and then insert the phone number you want to dial to. (A modem is required for voice transition.) page105
Intelligent Surveillance Solution
5. Configuration
Note:
1. You must use a modem with voice capability.
2. You may select a Wave format file; it will be played in the phone to alarm the person who picks up the phone call.
GSM modem:
Set the Port and Baud Rate of the GSM modem device, and then enter PIN code. You can setup the interval of send SMS message. You may click on Test to send test SMS message.
Note:
The interval is set to restrict the period of two SMS. If you set as 60 min, the SMS between 60 min would be deleted and didn’t send to user. page106
Intelligent Surveillance Solution
5. Configuration
5.6 Setting - Address Book
Address Book:
Manage the address book from which you may send out a phone call or an E-mail when an unusual event is detected. page107
Intelligent Surveillance Solution
5. Configuration
5.7 Setting – Monitor Display
Playback Option Cameras List
Auto Scan
Layout
Playback Option:
Execute Playback on the secondary monitor by checking the box. Make sure to adjust the display setting of your computer in advance to avoid system error.
Cameras List:
The left side displays a list of all cameras; modify the cameras shown on primary/ secondary monitor in the right window.
Auto Scan:
Activate auto scan to rotate the channels/ cameras on the display screen.
For instance, you may select to show only 4 sub-screens on the main console while having 16 channels connected to the system. With auto scan function, you will be able to see all 16 channels by turns. You can set up a primary channel that will always be on the screen and a secondary channel that has secondary priority.
Layout:
Choose the number of divisions for NxN division on the Main
Console screen.
Note:
For SCB-5000 H.264 Hardware compression system, only network cameras (IP Channels) can be shown on the secondary monitor. page108
Intelligent Surveillance Solution
5. Configuration
5.8 Setting – Joystick
Function Parameter
Import
Export Default
Function:
You can choose the function from the drop-down menu for the button of joystick. page109
Intelligent Surveillance Solution
5. Configuration
Note:
Following is a complete list of all log types:
1. N/A
2. Goto Preset Point
3. Goto Camera
4. Goto Previous Camera
5. Goto Next Camera
6. Switch Screen Layout
7. Toggle Single Camera View
8. Toggle Full Screen
9. Start/Stop Auto Scan
10. PTZ Speed Up
11. PTZ Speed Down
12. Zoom Wide
13. Zoom Tele
14. Start/Stop Patrol
15. Switch Active Monitor
Parameter:
You can choose the parameter of the function from the drop-down menu.
Default:
You can set the default setting for the joystick.
Export:
You can export the setting of the joystick.
Import:
You can import the setting of the joystick. page110
Intelligent Surveillance Solution
5. Configuration
5.9 User Account Setting
Only default admin account could manage the user accounts here. From the list on this tab, highlight each account and modify the privilege setting.
There are 3 default privilege profiles of account groups: y
Admin: Have privileges of all system functions and devices, except add/delete/update privileges of other users. y
Power User: Have limited privileges of system functions and complete privileges of assigned devices. y
User: All the privileges of system functions are forbidden, user could only manage assigned devices.
User account Setting
Privilege
Add Delete Default Update
y
Add: Click it to create a new account after inserting related information.
page111
Intelligent Surveillance Solution
5. Configuration
Note:
The “Add” button is only enabled when filled a new account. y
Delete: Click it to delete the indicated account.
y
Default: Click it to go back to default privilege settings of related user group.
y
Upgrade: Click it to save the modifications of each account.
User Account Setting:
The admin may create and modify the content of user account here. y
Name: Insert the user name.
y
Group: Assign the group for each user.
y
Description: Insert the description related to each user.
y
Password: Insert the password assigned to each user.
y
Password confirm: Insert again to confirm the password.
y
Disable User Account: Check the “Disable User Account” will block this account to access system. The signal “ ” will appear after disabling the account
Note:
Only the default admin account couldn’t be disabled. y
Keep remote login for___minutes: Insert the duration to auto kick out account after logging in from remote LiveViewer or Remote Playback server.
Privilege:
Check each privilege of functions and devices for each user account. y
Function: Check the settings and operations related system configuration, and the privilege of remote access.
y
Device: Check the device privileges of camera, digital output and
POS in MainConsole and client applications.
Note:
The privilege of default admin account couldn’t be edited. page112
Intelligent Surveillance Solution
5. Configuration
5.10 License Manager
The license of the software should be registered first before operating the former version of Intelligent Surveillance System.
Execute the License Management Tool in Config >License Manager to activate the license from dongle or serial number allocated with the software package, or de-activate the license then bring it to another
PC to activate it again.
Note:
Please refer page 169 for the detail setting of License Management
tool. page113
Intelligent Surveillance Solution
5. Configuration
5.11 Save/ Load Configuration
The Save/ Load Configuration function allows system users to save any specific setting as a cfg (config) file. You may save up several different cfg files at any time.
Save Configuration:
To save a specific setting, go to Config > Save/ Load
Configuration > Save. In the popup window, type in the file name and then save it as a cfg file.
Load Configuration:
To load a specific setting, go to Config > Save/ Load
Configuration > Load. In the popup window, go to the directory that you saved the cfg files at, select any one of them and then click OK to load the file.
Note:
MainConsole will be automatically shutdown after loading a new configuration. Please re-start MainConsole manually. page114
Intelligent Surveillance Solution
5. Configuration
5.12 Counting Application
Step 1
Step 2
Step 3
Start Simulation
Options Runtime
Step 1: Check the box of the camera to apply the Counting Application to it.
Step 2: In Operation section, check the option “Define detection zones” and drag the cursor to draw Region 1 and Region 2 on the Video Preview.
Step 3: In Operation section, check the option “Define object size” and drag the cursor to define the object size on the Video Preview. Objects that are about the size will be counted while going across these two regions.
Options:
1Way Counting will take objects going from Region 1 to Region 2 as one count. In 2Way Counting mode, it counts either going from Region
1 to Region 2 or from Region 2 to Region 1.
Runtime:
Check the boxes to show the counting result on the screen and/ or show object bounding box, which draws the shape of the object that the system detects in red squares. You can choose from the drop-down menu of how long you want to reset the counting number.
Start Simulation:
Click to test the setting. page115
Intelligent Surveillance Solution
5. Configuration
5.13 POS Application
Each NUUO Main Console system can manage up to 64 POS cash register devices. The POS Application tool is help to configuration POS devices, please refer the User manual of POS for detail. page116
Intelligent Surveillance Solution
5. Configuration
5.14 Network Service
There are 5 types of network services:
Live streaming server, Remote playback
server, 3GPP service, Remote Desktop, and Central Management Service. From the Main Console, go to Config > Network
Service to obtain the Network Service panel.
5.14.1 Live Streaming Server
When starting the live streaming function of computer, the system allows remote users to log in to the specific computer and view cameras that are connected to it. As system administrator, user could be able to monitor these accounts in order to maintain the system efficiency.
Main
On Live Streaming Server panel, administrator can see all the clients who are currently logging in to the computer and watching the live video from the remote side.
Client
Service
Options
Client list:
y
Client Count: Show the amount of channels that are connecting to system. page117
Intelligent Surveillance Solution
5. Configuration
y
Kill Client: Highlight an IP address and click on the “Kill Client” button to block the client from your client list. y
Kill All Clients: Click on this button, and then block all the clients logging to your system.
Service:
y
Server Status: Click on Start/Stop to turn on/off this option.
Options:
Adjust the setting only when the server is stopped. y
Port: Assign a port for the clients to connect to your system via
Remote Live Viewer. Default port is 5150. y
Maximum Connections: Number of connections that are allowed to connect to the system. Default is 16 channels and maximum is 128, one camera video counts as one connection. y
Use Default Web Server: Activate the Web server by checking the box; clients will be able to watch live video via Internet Explorer. The port for live streaming server is set to 80 by default.
Note:
Must check this item for system access via IE*. y
Save Log: Save the log information at appointed folder. y
Enable Audio: Select this option to enable the audio transmission along with video stream.
Black / White List
Enable list
IP address
Black/
White list
Apply to all
page118
Intelligent Surveillance Solution
5. Configuration
y
White List: Check the “Enable White List” box to activate the white list filter. Only IP from the white list is allowed to log in. y
Black List: Check the “Enable Black List” box to activate the black list filter. IP from the black list will be blocked. y
IP Address: Enter an IP address into the IP address field on the left. To add an IP address range to the system, enter 2 sets of IP address to indicate a series of IP(s). y
Add/Delete: Add the IP(s) onto the list or remove it from the list. y
Apply to All Network Servers: Apply the settings to both live streaming server and remote playback server.
Performance
Total bit rate
Individual Camera bit rate information
Live Streaming Server log information
page119
Intelligent Surveillance Solution
5. Configuration
5.14.2 Remote Playback Server
When starting the remote playback function, the system allows remote users to log in to the specific computer and withdraw data files that are stored on it. As system administrator, user could be able to monitor the accounts logging in to maintain the system efficiency.
Main
On Remote Playback Server panel, administrator can see all the clients who are currently logging in to the computer and watching the playback video from the remote side.
Client
Service
Options
Client list:
y
User Count: Show the amount of users that are connecting to system. y
Kill Client: Highlight an IP address and click on the “Kill Client” button to block the client from your client list. y
Kill All Clients: Click on this button, and then block all the clients logging to your system.
Service:
y
Server Status: Click on Start/Stop to turn on/off this option. page120
Intelligent Surveillance Solution
5. Configuration
Options:
Adjust the setting only when the server is stopped. y
Port: Assign a port for the clients to connect to your system via
Remote playback server. Default port is 5160. y
Maximum Users: Number of connections that are allowed to connect to the system. Default is 8 users and maximum is 64.
Note:
One user counts as one account that is logging in to the server. y
Use Default Web Server: Activate the Web server by checking the box; clients will be able to watch live video via Internet Explorer. The port for live streaming server is set to 80 by default.
Note:
Must check this item for system access via IE*. y
Save Log: Save the log information at appointed folder.
Black / White List
Enable list
IP address
Black/
White list
Apply to all
y
White List: Check the “Enable White List” box to activate the white list filter. Only IP from the white list is allowed to log in. y
Black List: Check the “Enable Black List” box to activate the black list filter. IP from the black list will be blocked. y
IP Address: Enter an IP address into the IP address field on the left. To add an IP address range to the system, enter 2 sets of IP address to indicate a series of IP(s). y
Add/Delete: Add the IP(s) onto the list or remove it from the list. y
Apply to All Network Servers: Apply the settings to both live streaming page121
Intelligent Surveillance Solution
5. Configuration
server and remote playback server.
Performance
Total bit rate Individual Camera bit rate information
Remote playback Server log information
page122
Intelligent Surveillance Solution
5. Configuration
5.14.3 3GPP Service
When starting the 3GPP service function of your computer, the system allows remote users to log in and view cameras that are connecting to it with 3GPP supported mobile phone. See Appendix A for more details about 3GPP Service.
Client
Service
Options
Client list:
y
Client Count: Show the amount of channels that are connecting to system.
Service:
y
Server Status: Click on Start/Stop to turn on/off this option.
Options:
Adjust the setting only when the server is stopped. y
Port: Assign a port for the clients to connect to your system via 3GPP
Service. Default port is 554. y
Enable User Authentication: User need to insert the username and password to login to the 3GPP server and view the video stream. page123
Intelligent Surveillance Solution
5. Configuration
5.14.4 Remote Desktop
When starting the Remote Desktop option, the system allows remote users to use NUUO Remote Desktop Tool to login and configure system. See
Appendix B to install and use this tool.
Option
Authentication
Server Status
Options:
y
Port: Assign a port for NUUO Desktop tool to login and configure system. y
Disconnect idle client after (300~3600 sec): Auto disconnect the on-line user who idled more than setting period.
Authentication:
Enable this option would only allow admin account to use NUUO Desktop tool to login system.
Service:
y
Server Status: Click on Start/Stop to turn on/off this option. page124
Intelligent Surveillance Solution
5. Configuration
5.14.5 Central Management Service
This service only supports NUUO Central Management System (NCS). When starting the Central Management Service option of the system, the Main
Console would send event information to NCS and allow NCS system to control I/O device from remote side.
Note:
1. To enable this action, go Guard >Action and select “Send to Central
Server” to enable the action triggered by preference event.
2. Please refer the user manual of Central Management System for detail information.
Client
Service
Options
Client list:
y
Client Count: Show the amount of NCS Servers that are connecting to system. y
Kill Client: Highlight an IP address and click on the “Kill Client” button to block the client from your client list. y
Kill All Clients: Click on this button and then block all the clients logging to your system.
Service:
y
Server Status: Click on Start/Stop to turn on/off this option.
Options:
Adjust the setting only when the server is stopped. page125
Intelligent Surveillance Solution
5. Configuration
y
Port: Assign a port for NCS System to connect Main Console system.
Default port is 5170. y
Maximum Connections: Number of connections from NCS Servers that are allowed to connect to the system. The default is 8 NCS Servers and maximum is 16. page126
Intelligent Surveillance Solution
5. Configuration
5.15 About Main Console
Go to About Main Console to view the version of your surveillance system and the hardware information.
5.16 Video Source
(For system with MPEG4 capture device only)
Step 1: Go to Video Source to adjust the Video Standard to NTSC or PAL.
Step 2: Adjust the maximum Video Resolution for all analog cameras.
Step 3: Add new cameras in Camera Number.
Step 4: Click “Sync all video signal level after pressing OK” to synchronize video signal level to the optimized display (Auto-gain control). page127
Intelligent Surveillance Solution
6. E-Map
6. E-Map
With E-Map, user can find out or track the actual location and alarm status easily and receive instant response when the event happens.
The arrows and lightening icon on E-Map represent cameras and
I/O devices and these icons will turn red once they are triggered by alarms.
To launch E-Map application, simply click on Start and select
Open E-Map from start menu to open E-Map window. page128
Intelligent Surveillance Solution
6. E-Map
There are 2 modes in E-Map application:
Edit mode: Allow users to add/edit maps and indicators of devices. In
Edit mode, the function buttons on the bottom of the window will be active, and then setup the configuration before running E-map function at the first time.
Operate mode: all settings will be activated in this mode.
6.1 Edit Mode
To carry out edit function, you need to be in Edit Mode.
Function button
6.1.1 Add/Edit/Delete Map
Edit mode/ Operate mode
Switch button
Add E-Map:
Step 1: Make sure being in “Edit Mode” and all devices are connected and inserted.
Step 2: Right click on the “Map ” icon in device and map list to obtain the option menu to add map, or just click “Add Map” button to obtain the “Map Config” dialog.
page129
Intelligent Surveillance Solution
6. E-Map
Step 3: Select the map file and insert the map name. Click “OK”, and then the map you added appears in the tree structure of device and map list.
Step 4: The map indicator appears on the left-up corner of parent map.
Drag it to the position you want on appointed map.
Edit E-Map:
Step 1: Make sure being in “Edit Mode” and all devices are connected and inserted.
Step 2: Right click on the “Map ” icon to obtain the option menu to edit map, or just click “Edit Map” button to obtain the “Map Config” dialog.
Step 3: Modify the required details, and then click “OK” to save configuration.
Delete E-Map:
Step 1: Make sure being in Edit Mode and all devices are connected and inserted.
Step 2: Right click on the “Map ” icon to obtain the option menu to delete map, or just click “Delete” button to remove appointed map from list.
Note:
The root map can’t be deleted.
6.1.2 Add/Rotate/Delete Device Indicator
Add Indicator:
Step 1: Make sure being in Edit Mode and all devices are connected and inserted. page130
Intelligent Surveillance Solution
6. E-Map
Step 2: Select on the icon “ Map” which you want add device indicator to.
Step 3: Before adding indicator, ensure that the map you want is displayed. Select device from list and directly drag a device to the desired location on the map.
Note:
Different device is symbolized by different indicator.
- Camera indicator, - digital Input indicator, -POS indicator.
Rotate Indicator:
Step 1: Ensure being in Edit Mode and all devices are inserted. Select device indicator from map or form Device and Map list. The device indicator will be marked with a green ring .
Step 2: Click “Rotate” button, the indicator will rotate 45 degree.
Note:
Only camera indicators are allowed to be rotated.
Delete Indicator:
Step 1: Ensure being in Edit Mode and all devices are inserted. Select device indicator from map or form Device and Map list. The device indicator will be marked with a green ring .
Step 2: Click “Delete” button, the indicator will be gone. page131
Intelligent Surveillance Solution
6. E-Map
6.2 Operate Mode
To carry out the operation functions in E-Map, you need to be in Operate
Mode.
6.2.1 Device and Map Tree list
Operate mode/ Edit mode
Switch button
This window will list all devices and map hierarchies; click device or map indicator to show related information on E-Map windows.
Map – Select the map you want to show on E-Map Window.
Camera – Select the camera you want to preview video on preview window and mark indicator on E-map.
Digital Input – Select it to highlight the device with green ring on map and show status on Information window. If the Digital Input is from IP camera, the preview window will display live video of the camera.
Digital Output – Select it to highlight the device with green ring on map and show status on Information window. If the Digital Output is from IP camera, the preview window will display live video of the camera.
POS – Select it to highlight the POS device with green ring on map and display live video of first associated camera on preview window.
page132
Intelligent Surveillance Solution
6. E-Map
6.2.2 E-Map picture
This window will show the map layer and indicators.
Device Indicator:
Select device indicator form Device and Map Tree list to show preview video and related information.
Map indicator:
Select map indicator will enter the next map layer. If you want move to upper layer, right click on the map to select Up option or click right on the map layer
6.2.3 Information and Preview window
This window will show the related information of each indicator.
Map Info – Show map name.
Camera – Show camera name and connecting status.
Digital Input – Show Digital Input name and status (0 or 1).
Digital Output –Show Digital Output name and status (0 or 1).
POS – Show POS device name, connecting status, first associated camera name and connecting status. page133
Intelligent Surveillance Solution
6. E-Map
6.3 Layout Adjustment
Triangular
indicator
6.3.1 Adjust layout window
Shrink the window:
Click “ Triangular indicator” to hide the Device and Map/ Preview and
Information window on right and left side. click triangular indicator again to go back to default setting.
Full screen display:
For the system with Dual- Monitor, user can view the MainConsole on primary monitor, and view the full-size E-Map on secondary monitor.
Step 1: Click “ Triangular indicator” to hide the Device and Map/
Preview and Information window on right and left side.
Step 2: Click “ ” on right top of the window, and then get the full screen mode of E-Map. page134
Intelligent Surveillance Solution
7. Log Viewer
7. Log Viewer
View the unusual event history that had been detected by the
Smart Guard System.
To launch Log Viewer and get report, simply click on Config and select Log Viewer from menu to open Log Viewer window page135
Intelligent Surveillance Solution
7. Log Viewer
7.1 Unusual Event
Step1
Step2
Step3
Step 4
Step1: Choose the type of events you wish to view or select “All” from the drop-down menu to view all types of events. The types of Unusual Event include General Motion, Foreign Object, Missing Object, Focus Lost,
Camera occlusion, Signal Lost, Disk Space Exhausted, System Health
Unusual and Digital Input Triggered .
Step 2: Choose the camera channel you wish to view or select “All” for all the channels available.
Step 3: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 4: Click Search.
Note:
When working with a video record,
1. Log Viewer will search for Unusual Event in the video record in Date &
Time mode, start from the beginning to the end of the record, which is the default setting of the system page136
Intelligent Surveillance Solution
7. Log Viewer
7.2 System Log
Select Log Type form the drop-down menu. There are total 31 types of log types, including:
1. Main Console Startup
2. Main Console Shutdown
3. User Login
4. User Login Failed
5. Start Schedule
6. Stop Schedule
7. Execute Recycle
8. Enable Channel
9. Disable Channel
10. Start Smart Guard
11. Stop Smart Guard
12. Modify Smart Guard
13. Modify Schedule
14. Modify Configuration
15. Start Live Streaming Server
16. Stop Live Streaming Server
17. Modify Live Streaming Server
18. Start Remote Playback Server
19. Stop Remote Playback Server
20. Modify Remote Playback Server
21. IP Camera Connection Lost
22. Auto Restart Windows
23. Modify POS Setting
24. POS Connection Lost
25. Modify E-Map
26. Start Remote Desktop
27. Stop Remote Desktop
28. Modify Remote Desktop
29. Start Central Management
30. Stop Central Management
31. Modify Central Management
Step 1
Step 2
Step 3
Step1: Choose the type of event you want to check or select “All” from the drop-down menu for all types of events.
Step 2: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search. page137
Intelligent Surveillance Solution
7. Log Viewer
7.3 Counting Application
Display the history of Counting Application during a given time period.
Step 4
Step1: Select the channel you want to check or select “All” from the drop-down menu for all channels.
Step 2: Select search period. View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search.
Step 4: Press the button “Export to”.
Step 5: Type the file name and choose the file format (.xls or .txt). page138
Intelligent Surveillance Solution
7. Log Viewer
7.4 Counting Application (Diagram)
Display the Counting Application data in diagram format.
Step 4
Step1: Select the channel you want to check or select “All” from the drop-down menu for all channels.
Step 2: From the drop-down menu, set up how you would like the diagram to be displayed. You have the options of one day, one month, or one year.
Step 3: Select a specific date to make it the start point of the diagram.
Step 4: Click Search.
Step 5: Press the button “Export to”.
Step 6: Type the file name and the file will save as BMP files. page139
Intelligent Surveillance Solution
7. Log Viewer
7.5 POS Log
View the POS Log history that had been detected by the Smart Guard
System.
Step 5
Step1: Choose the type of events you wish to view or select “All” from the drop-down menu to view all types of events. The types of Unusual Event include Transaction Start, Transaction End, Open Cash Register,
Connection Lost, and special User defined event. Please refer the User manual of POS for detail.
Step 2: Choose the camera channel you wish to view or select “All” for all the channels available.
Step 3: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 4: Click Search.
Step 5: Press the button “Export to”.
Step 6: Type the file name and choose the file format (.xls or .txt). page140
Intelligent Surveillance Solution
7. Log Viewer
7.6 Export and Backup Log
View the Export and Backup Log history that had been operated by local
or remote user.
Step1: Choose the type of event you want to check or select “All” from the drop-down menu for all types of events.
Step 2: View the events that happened on a particular date or during a given time period by selecting search period.
For a particular data: check the “Date” box right and indicate the date.
For a period: check the “Date&Time” and then enter the date and time.
Step 3: Click Search page141
Intelligent Surveillance Solution
7. Log Viewer
7.7 Export
After search the log you want, just export it to .xls or .txt file.
Step 1
Step1: Press the button “Export to”.
Step2: Type the file name and choose the file format (.xls or .txt).
.xls .txt
page142
Intelligent Surveillance Solution
8. Backup
8. Backup
The backup function saves video record and other log information. User may open backup files on any PC with
Windows Operation System and operate the full function
Playback panel on it. Follow the instructions below to obtain backup files. page143
Intelligent Surveillance Solution
8. Backup
8.1 Backup Recorded file(s)
Step 1
Step 2
Step 3
Step 1: Add (Remote) Backup Site :
Press the “Remote Sever ” can go to remote backup site management to add and setup the backup site. y
Enter the IP address or DNS, Port,
Username, and Password. y
Click “Add” to add the server. y
Click OK to exit the Setting panel.
Step 2: Access (Remote) Backup Site : Click on the icon and insert the username/password of the remote server to access the backup Site.
Step 3: Click on “New Period” to obtain the Select DateTime Period panel.
Step 4: Select the data you want to backup by highlighting the time period. Besides the time-table, you may also set up start time and end time in the Date Time Period section. page144
Intelligent Surveillance Solution
8. Backup
Step 4
Step 5
Step 6
Step 5: Click on the camera number icon to add camera(s)
Step 7
or click to add/delete all the channels.
Step 6: Check the box of Enable Preview to get the preview of the video you select.
Step 7: Click OK when the settings are complete and go back to the
Backup System panel.
Step 8: If there is any data period not wanted, click Remove Period to remove the data period on the backup list.
Step 8
Step 9
page145
Intelligent Surveillance Solution
8. Backup
Step 9: Click the Backup icon to obtain Backup panel.
Step 10
Step 11
Step 12
Step 10: Summary: Check the summary section to see the size of the file(s).
Step 11: Media: Choose the path you want to save the file or burn the file into a CD (direct CD burning for Windows XP only), DVD or on Hard Disk.
Step 12: Option: Select the log information you would like to backup
(Event Log, System Log , Counter Log and POS Transaction), and then click OK.
8.2 Delete Recorded file(s)
Step 1: Click on “New Period” to obtain the Select Date Time Period panel.
Step 3
Step 1
page146
Intelligent Surveillance Solution
8. Backup
Step 2: Follow step 3-7 on above (backup) section to select data period which you want to delete.
Step 3: Click on the “Delete” icon and delete all the data in the backup list from the database.
Note:
The deleted video cannot be recovered.
page147
Intelligent Surveillance Solution
9. Remote Live Viewer
9. Remote Live Viewer
With the Remote Live Viewer console, remote users may watch up to 128 channels real-time video from remote live streaming servers. page148
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1 Setting
Click General Setting to obtain setting dialog.
General Setting
9.1.1 General Setting
Audio preview:
y
Enable audio on active channel: Select it to enable the audio streaming on active channel.
Miscellaneous:
y
Synchronize video frames: Select it to avoid the tearing problem occurring in video display while increasing the CPU loading. page149
9.1.2 Server setting
Intelligent Surveillance Solution
9. Remote Live Viewer
Server List
Step 1: Enter the Server Name as preference.
Step 2: Enter the Address, Port, User Name, Password to log in the server.
Step 3: Enable the Save Password to login without entering the password again.
Step 4: Enable the Auto Login to login automatically when starting the
Remote Live Viewer.
Step 5: Click on Test Server to check if the server is available.
Step 6: Click “Add” to insert the setting to server list.
Note:
To change the setting, select a server on server list and click “Update” after modify setting.
To remove the server, select a server on server list and then click “Delete”. page150
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1.3 Group Setting
Allocate different cameras into each appointed group.
Step 2
Step 4
Step 1
Step 3
Step 1: Log in to all the servers that contain the camera(s) you would like to put into the group(s).
Step 2: Click “Insert” to create a new group; name the group for future reference.
Step 3: From the window at the right, highlight the camera(s) that you would like to add to a group and then click on the “ <-- ” button. Repeat the process until satisfied with the group setting.
Step 4: Click on the “Delete” and “Rename” button to remove or rename a specific group.
Step 5: Repeat Step 2 to 4 to adjust the group setting until satisfied.
Step 6: Click OK. page151
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1.4 Camera Setting
Select prefer stream type of each camera as default live view profile.
Stream Profile Info:
y
Stream profile: The list would different with video input type of server
Auto:
The system will adjust the stream type automatically to fit different screen division.
Recoded:
The system will follow the stream profile set in Main Console >Schedule
> Encoding Options.
High / Normal / Low/ Minimum / H.264 (SCB-7000s only):
The system will follow the stream profile set in Main Console > Setting >
Camera > Stream Profile.
Original (IP only):
The system will display the streaming directly form IP camera and video server. y
Copy to: Select it to copy the preferred stream profile of a channel to all the channels in list. page152
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1.5 OSD Setting
Adjust font style of Camera OSD on this panel.
9.1.6 POS Setting
Adjust font style of POS overlay on this panel. page153
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1.7 Monitor Display Setting
Activate auto scan to rotate the channels/ cameras on screen.
Note:
1. For instance, you may select to show only 4 sub-screens on the live viewer while having 16 channels connected to the system. With auto scan function, you will be able to see all 16 channels by turns.
2. Each monitor support up to 8x8 layout with auto scan function to show
128 channels.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 1: Select the Monitor connected to the system.
Step 2: Auto scan group: Select appointed server group to activate auto scan settings.
Step 3: Primary channel: Select appointed channel that will always be on the screen when activating auto scan settings.
Step 4: Secondary channel: Select appointed channel that has secondary priority then primary channel on the screen when activating auto scan settings. page154
Intelligent Surveillance Solution
9. Remote Live Viewer
Step 5: Layout: Select the screen division of “NxN type”in Remote live viewer panel.
9.1.8 Notification Setting
Status display:
y
Show recording status: Select it to show the crystal ball with recording status on monitor display. y
Show camera event: Select it to show the smart guard detected event appointed in Main Console on each channel.
Note: To execute this function, need setup on screen display as an action of Smart Guard instant response. y
Show counting result: Select it to show the counting result appointed in Main Console on each channel.
Miscellaneous:
y
Popup system event: Select it to allow the System event appointed in Main Console popping up a message to warn. page155
Intelligent Surveillance Solution
9. Remote Live Viewer
9.1.9 Joystick Setting
Please switch to Joystick tab and the configuration is the same as on
Main console, please refer page 109 for details.
page156
Intelligent Surveillance Solution
9. Remote Live Viewer
9.2 Server/Group/Camera
Display a complete list of the server(s),group(s) and camera(s) that are added to the system.
Server View: The cameras would list beyond associated server.
Group View: The cameras would list beyond customized grouping.
Server View Group View
9.2.1 login/logout server
Option1: Select a server on list, and then click on the LOG IN/ LOG OUT icon to access/ leave the server.
Option2: On the server list, right click on it to obtain the menu options.
Log In/Log Out Server
9.2.2 Connect/Disconnect camera
Option1: On the server/camera list, double click on a camera to connect it.
Option2: On the server/ camera list, right click on a camera to obtain the menu options to connect/ disconnect it.
Connect/Disconnect Camera
Option3: Select a camera(s) from the list, and then drag it to where you want the image to be displayed. page157
Intelligent Surveillance Solution
9. Remote Live Viewer
Option4: Play / Stop/ Drop: Select a camera/ video and click on this button to play/stop/disconnect a particular channel.
Play
Stop
Drop
9.2.3 Multiple View:
Step1: On the server/ camera list, select a camera and right click on it to obtain the menu options.
Step2: Select “Duplicate Camera”, and the duplicate camera with green indicator will display below on camera list.
Step3: Double click on the duplicated camera to connect it and display on screen. page158
Intelligent Surveillance Solution
9. Remote Live Viewer
9.3 PTZ Control
Control the movement of PTZ cameras. With cameras that support PTZ control, you can move, zoom, patrol, adjust the focus, and set preset points of the cameras.
9.3.1 Preset/ Go
Adjust the camera view until satisfied. Click on the Set icon and set up the view as the preset point 01. Adjust the camera view again and set up the preset point 02. Repeat the process until finish setting up all preset points.
Enter any names you want instead of the preset point 01, preset point 02, preset point 03…, click on the Go icon and view the result of your setting.
Note:
For the speed settings of PTZ camera, please setup on Main Console
> Config > Setting>PTZ Config.
9.3.2 Zoom
Click on the + and – signs to zoom in and zoom out the view.
9.3.3 Focus
You can select to have the camera focused near or far. To focus near means objects that are closer will be clearer than the objects that are further away. On contrast, to focus far means objects that are further will be clearer than the objects that are closer. Click on the Focus icon and select auto focus if you want the system to decide the focus point for you.
9.3.4 Patrol
To control PTZ camera to patrol around pre-defined path of preset points, please click on Patrol button to start/stop patrol.
Note:
To setup patrol path, please setup on Main Console > Config >
Setting>PTZ Config > Patrol. page159
Intelligent Surveillance Solution
9. Remote Live Viewer
9.4 On Screen Menu
Right click on the camera screen and get the “On
Screen Menu”, from which you can quickly adjust the setting of camera.
9.4.1 Enable Move
With cameras that support PTZ function, the function allows to use mouse to control PTZ function by clicking display screen. To enable function: click the “Enable move” of on screen menu. To disable function: click the
“Disable Move” to cancel this function.
9.4.2 Enable Digital PTZ
To enable the digital PTZ functions of the video, select the “Enable digital
PTZ option”. Use mouse wheel or click on the + and – signs to zoom in and zoom out on the camera. The square flashing on the video grid indicate the correspondent view of the camera.
9.4.3 Stream Profile
The function helps to change video quality quickly by switch Stream
Profile.
9.4.4 Snapshot
The snapshot function could copy and capture a specific video image to the clipboard or to save as bmp file. The snapshot could customize to add
OSD, POS information, and captured selected range only when viewing video with digital zoom in.
9.4.5 Toggle Fullscreen
Switch to view video with full screen display. To disable the function, right click on screen and dis-select option or simply press “ESC” to go back to original window. page160
Intelligent Surveillance Solution
9. Remote Live Viewer
9.5 Start Monitor
Start Monitor
9.5.1 Multiple Monitor
Select open monitor to append monitor to view more live videos on multiple monitors. Each append monitor has the same list and view control buttons with Main monitor, except Start, Playback, and Setting buttons.
9.5.2 E-Map
Select Open E-Map to obtain the E-Map window, the GUI map help to find up devices easily and have information window to show the status of each device.
Map Info – Show map name.
Camera – Show camera name and connecting status.
Digital Input – Show Digital Input name and status (0 or 1).
Digital Output –Show Digital Output name and status (0 or 1).
POS – Show POS device name, connecting status, first associated camera name and connecting status.
9.5.3 I/O Control
Select it to obtain the I/O control panel, the panel helps to view status and control DO devices remotely.
Note:
Adjust the setting of I/O device in
Main console> Config>Setting>I/O
Device first, the I/O control panel will display the device status base on it. page161
Intelligent Surveillance Solution
9. Remote Live Viewer
9.6 Playback
Select it to obtain the Playback panel and view video remotely.
9.6.1 Add Remote Playback Site
Press the “Remote Sever ” can go to remote playback site management to add and setup the remote playback site.
Step 1: Enter the IP address or
DNS, Port, Username, and Password.
Step 2: Click “Add” to add the server.
Step 3: Click OK to exit the Setting panel.
9.6.2 Access Remote Playback Site
Go to Date/Time Panel and click on the icon on the top of the display window to access the Remote Playback Site page162
Intelligent Surveillance Solution
10.WebView
10. Web View
Server IP
Remote Live Viewer
Remote Playback
Note:
Must make sure the Liver Stream Server is enabled. Check 5.14
Network Service for more detail.
page163
Intelligent Surveillance Solution
10.WebView
10.1 Server IP
Open an Internet Explorer browser and enter the IP address or DDNS
“name” of the server followed by the connecting port.
Example: http://192.168.1.16:8080/
Note: 192.168.1.16 is the IP address of the server.
8080 is the port specified in “Use Default Web Server” in Network
Service.
10.2 Remote Live Viewer
Press this icon to use Remote Live Viewer which functions are the same
as Remote Live Viewer. See page148.
10.3 Remote Playback
Press this icon to use Remote Playback which functions are the same as
Playback but remote server and backup functions. See page 41.
page164
Intelligent Surveillance Solution
11.Utilities
11. Utilities
A. Verification Tool
B. License Management Tool
C. Resource Management Tool
D. DB Tool
page165
Intelligent Surveillance Solution
A. Verification Tool
A. Verification Tool
The Verification Tool verifies whether the data created by the system be tampered with or not. It is the process by which a digital watermark (a digital signature) is added to each recorded video frame to ensure its authenticity.
There are 3 types of data could be verified by Verification Tool:
1. File in (.dat) (.264) format will be displayed as .
2. File in (.avi) (.asf) format will be displayed as .
3. File in (.bmp) (.jpg) format will be displayed as .
1.1Execute Verification Tool
Step 1: Execute Verification Tool from program files.
Step 2: Insert the Password of administrator to log in.
Step 3: The verification tool appears after login.
Step 1
page166
Intelligent Surveillance Solution
A. Verification Tool
1.2 Verification Tool Overview
Add File Add Folder Remove File
Select All
Video Preview
Play Verify Pause Stop
Add File:
Click it to insert the single file to list for verification.
Add Folder:
Click it to choose the folder with multiple files to list for verification.
Remove File:
Click it to remove indicated file(s) from list.
Select All:
Click it to select all files in list for verification.
Note:
1. Choose the file type first before selecting files. Only (.dat) (.264)
(.avi) (.asf) (.bmp) (.jpg) are available to open.
2. User could also drag files to the list for verification.
Video Preview:
Check this column to preview indicated file in verification list. Select the button below preview window to play , Pause and
Stop the file previewed.
Note:
Preview of (.bmp) (.jpg) format is not allowed. page167
Intelligent Surveillance Solution
A. Verification Tool
1.3 Verify Image/Video
Step 1: Select single or multiple files for verification.
Step 2: Click “verify ”to start verification.
Step 3: The verification result will show on watermark column.
If a file was tampered with, it will show .
If a file passed verification, it will show .
Watermark
Verification report
Step 4: The verification report will show below to display the information related to verification. page168
Intelligent Surveillance Solution
B. License Management Tool
B. License Management Tool
The license of the software should be registered first before operating the former version of Intelligent Surveillance System.
Execute the License Management Tool to activate the license from dongle or serial number allocated with the software package, or de-activate the license then bring it to another PC to activate it again.
Both “On line” and “Off line” status of PC environment could execute the tool to “activate” or “transfer” the license. Below list 4 types of license management process:
- To “activate” the license with PC connected to network, follow the
“Activation On line” process.
- To “activate” the license with PC not connected to network, follow the
“Activation Off line” process.
- To “de-activate/transfer” the license with PC connected to network, follow the “Transfer On line” process.
- To “de-activate/transfer” the license with PC not connected to network, follow the “Transfer Off line” process.
Please refer below chapter for the detail steps of each process. page169
Intelligent Surveillance Solution
C. Resource Management Too
1.1 License Management Tool Overview
1.1.1 Execute License Management Tool
Step 1: Execute “License Manager” Tool in config menu or installation folders.
Step 2: The “License Management Tool” will appear. Please refer below for the tool overview.
1.1.2 License Management Tool Overview
Activate
Activate tab
SN status
Activate type
SN type
Activate
page170
Intelligent Surveillance Solution
B. License Management Tool
Transfer
Transfer Tab
SN status
Transfer type
Transfer
page171
Intelligent Surveillance Solution
C. Resource Management Too
1.2 Activate/Transfer License
1.2.1 Activate License
Activation Online
Step 1: Open “License Manager” Tool.
Step 2: Select “On line” as Activate type.
Step 3: Input the “SN (Serial number)”or “Import SN file”, and then click on
“Activate” button.
Step 4: Restart MainConsole if activated successfully.
Activation Off line
Step 1: Open “License Manager” Tool.
Step 2: Select “Off line” as Activate type.
Step 3: Insert the “SN”, and then click on “Activate” button. page172
Intelligent Surveillance Solution
B. License Management Tool
Step 4: Save “Request file” , and then take it to another PC connected to
Internet.
Step 5: Execute “ OffLineTool.exe ” in another PC , and then click
“Activate” to send request file to license server.
Step 6: Save “License file”, and then take it to original NVR system.
Step 7: Open “License Manager” Tool again, select “Import license file”, and then click “Activate” button to activate.
Step 8: Restart MainConsole if activated successfully. page173
Intelligent Surveillance Solution
C. Resource Management Too
1.2.2 Transfer License
Transfer On line
Step 1: Open “License Manager” Tool.
Step 2: Select “Transfer” Tab, and then check “On line” as Transfer type.
Step 3: Select “SN" and click on “Transfer” button.
Step 4: Restart MainConsole if activated successfully.
Transfer Off line
Step 1: Open “License Manager” Tool.
Step 2: Select “Transfer” Tab, and then check “Off line” as Transfer type.
Step 3: Select “SN”, and then click “Transfer” button to transfer SN. page174
Intelligent Surveillance Solution
B. License Management Tool
Step 4: Save “Request file”. Restart MainConsole if activated successfully.
Step 5: Copy request file to another PC connected to internet.
Step 6: Execute OffLineTool.exe in another PC, check Transfer SN and click
“Transfer” to send request file to license server.
Note:
User need to copy request file to another PC and send it to license server, otherwise the SN can’t be re-activate again!!
Step 7: Check Transfer Completed. page175
Intelligent Surveillance Solution
C. Resource Management Tool
C. Resource Management Tool
The Resource Management Tool could detect whether the system operation is normal or not.
Note:
For further application of Resource Management Tool, please refer
1.1 Execute Resource Management tool
Step 1: Open Resource Report from start menu.
Step 2: The Resource Management Tool will appear.
Step 1
1.2 System Resource Overview
System Resource History Diagram
Advanced
page176
Intelligent Surveillance Solution
C. Resource Management Tool
1.2.1 System Resource
System Health:
This item shows the system information, including “CPU
Temperature”, “Motherboard Temperature”, “CPU Fan Speed” and
“Power Fan Speed”.
Note:
User needs to install the “SpeedFan” first to gather the CPU and
Motherboard temperature information.
CPU Loading:
This item shows the percentage of CPU usage.
Memory Usage:
This item shows the memory usage of system. “Memory
Used” and “Memory Available” are included.
Logical Disk Free:
This item shows the percentage of available disk space for storage.
Note:
The disk directory will be the same as the one in
MainConsole>Config>Setting>Storage>Location.
Network Utilization :
This item shows the total upload and download bit-rate utilization of the running computer.
1.2.2 Instant Diagram
Click each item in the left list to obtain the instant system diagram. The
“system resource” will be displayed as each variable in Vertical Axis; The unit of Horizontal Axis will be displayed as “Per Second”.
Vertical Axis
Horizontal Axis
page177
Intelligent Surveillance Solution
C. Resource Management Too
1.3 Advanced Resource Report
Click “Advanced button to search and export system logs in “Search” tab and obtain the history diagram of an specified period in “Diagram” tab.
1.3.1 Search
Step 4
Step 3
Step 1
Step 2
Step 5
Step 1: Choose the system event type, and then select the standard percentage to search system log.
Step 2: Select the Date/DateTime duration to search system log.
Step 3: Click “Search” to start searching, the system logs will be listed below.
Step 4: Click “Export to” to save the system log in (*.xls) or (*.txt) format.
Step 5: Click “OK” to close the report window. page178
Intelligent Surveillance Solution
C. Resource Management Tool
1.3.2 Display
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 1: Choose the system event type.
Step 2: Select the DateTime to draft history diagram.
Step 3: Setup the start time and duration for charting. User can choose
“One Day”, “One Hour” or “One Minute” as the duration.
Step 4: Click “Display” to start charting, the diagram will be displayed at below column.
Step 5: Click “Save” to save the diagram in (*.bmp) format.
Step 6: Click “OK” to close the report window. page179
Intelligent Surveillance Solution
D. DB Tool
D. DB Tool
The DB Tool Repair database files and Export configurations.
Warning : improper use of this DB Tool may cause lose of the recorded video data.
Step 1: Execute DB Tool from program files.
Step 1
Step 2: Enter the password of administrator to log in.
Step 2
page180
Intelligent Surveillance Solution
D. DB Tool
1.1 Repair Database
This page has three repair method, Modify Location, Verify Only, and
Repair.
For modify location propose:
NUUO Playback system can recognize all recording video in the folders which list on MainConsole > Config > Setting > General page.
For some reason, user need use Playback system to open recording video beyond storage location setting. For this propose, user could follow below steps to modify location by DB tool.
Note: The default storage location of system is on your_installation_directory, (ex: C:\Program Files\NUUO\SCB_IP)
Step 1: Select Repair database.
Step 2: Select the repair Method as Modify Location.
Step 3: For add database location, please click on button and use
URL to choose location.
For remove database location, please choose location form list and click on button to remove location. page181
Intelligent Surveillance Solution
D. DB Tool
Step 4: Click on Modify button to modify location. After modification, the Modify Result will show on the panel.
Example of modify database:
In certain case that when video data needs to be transfer from old PC to another new PC, user will need to perform the following procedure.
1. Manually copy all recorded video data from the default installation path or other user-defined storage path of the old PC.
Recorded video data
2. Manually paste all recorded video data to the default installation path or other user-defined storage path of the new PC
3. Follow previous page to add new location on new PC.
4. Old recorded video data can be viewed by NUUO playback system on the new PC.
For verify and repair proposes:
This tool is using to check and repair your database and recording video with below problems:
(1) If there are records in database, but no video file, use this DB Tools to delete records.
(2) If there are video files but no record in database, use this DB Tools to rearrange the database and find these records. page182
Intelligent Surveillance Solution
D. DB Tool
Step 1: Switch to Repair database windows.
Step 2: Select the repair Method as Modify Location.
Step 3: Check the video location windows.
The system will list all video locations in table, but if there are any omit, please use to insert.
Note: After inserting location, the system will show files count below table.
Step 4: Choose the method of “Verify Only”, and click “verify”. This method will only check the files without modify. Verify result will show how many files broken or missing.
Step 5: Choose the method of “Repair(Complete)”, and click
“Repair” to repair. The Repair Result will show how many files are fixed and inserted.
Step 6: The repair new database will replace old ones. And the original database will change file names with extend repair date and time as below. page183
Intelligent Surveillance Solution
D. DB Tool
Note: Open Log is a tool to record repair database recode. It will recode repair method, file operation, strat time and end time. page184
Intelligent Surveillance Solution
D. DB Tool
1.2 Export Configurations
This tool is using when user want to export all configuration to backup, take to another PC for NUUO technical trouble shooting.
Step 1: Press “Export”.
Step 2: Select the location you want to Export and type the name of the configurations.
Step 3: Press “Save” to start to import database. page185
Intelligent Surveillance Solution
Appendix A
Appendix A - 3GPP Service
How to setup 3GPP streaming connection (using BenQ-Siemens mobile phones)
System Configuration
NUUO DVR / NVR server v2.6
CPU:
Memory:
Intel core2 Duo 1.86 GHz
512 DDR RAM
Ethernet: Realtek RTL8168/8111 PCI-E
Hard Disk: 160GB
Graphic card: ASUS Extreme AX550
Operating System: Windows XP Professional SP2
Mobile Phone:
BenQ-Siemens E81
1.1 Configuration from NUUO server
Step 1 : Go to Config and select Network Service page186
Intelligent Surveillance Solution
Appendix A
Step 2 : Select 3GPP Service, and then click Start
Note: In the Option item, the “port” selected here is the same port from mobile handset
1.2 Configuration from 3G Mobile Phone
1.2.1 BenQ-Siemens E81
Step 1: Goto Menu, then Internet page187
Step 2: Select Bookmarks
Intelligent Surveillance Solution
Appendix A
Step 3: Add New Bookmark
Step 4: Configure the Adress setting as the following example.
Ex: rtsp://61.216.97.69:554/
media00
.3gp
61.216.97.69:554 is the IP address of NUUO NVR or DVR system
Port :
port specified in 3GPP Service from NUUO NVR or DVR system page188
Intelligent Surveillance Solution
Appendix A
Step 5: Save the settings and start playing page189
1.2.2 BenQ P50
1. Connect GPRS
Intelligent Surveillance Solution
Appendix A
2. Download and install the [PLATFORM4] software.
3. Execute NUUO Main Console. page190
Intelligent Surveillance Solution
Appendix A
4. Press the [Config]Æ[Network Service]Æ[Start]
5. Open [PLATFORM4], press the button framed by red into Option page191
Intelligent Surveillance Solution
Appendix A
6. [Open Url] enter the rtsp address of the camera
(EX: rtsp://61.216.97.69/media00.3gpÆchannel 1
EX: rtsp://61.216.97.69/media01.3gpÆchannel 2
EX: rtsp://61.216.97.69/media02.3gpÆchannel 3)
7. [Setting I]change the setting and press “OK”
[Protocol] TCP
[Buffer Size] 60
[Connection TimeOut] 103
[Data Recept. TimeOut] 100
[Deblocking Filter] check page192
Intelligent Surveillance Solution
Appendix A
8. Go back to PLATFORM4, searching and then getting the video page193
Intelligent Surveillance Solution
Appendix B
Appendix B – PDA / Smart
Phone Client
PDA / SP (Smart Phone) Client are only applied for devices with Windows
Mobile 5.0 platform or above. See the sections below to find how to install and execute PDA / SP Client.
Note:
1. The different between Smart Phone and PDA Client is navigation of operation, user can only control client with phone buttons.
2. The resolution of PDA / SP Client is limited in 240*320 (QVGA).
1.1 Install PDA / Smart Phone Client
Step1: Connect mobile device to the PC.
Step 2: Insert the installation CD and click on PDA Client Installation /
Smart Phone Client Installation to install application in device.
Note:
If you do not have Microsoft® ActiveSync installed, a message will appear “Can not find ActiveSync. Please reinstall
ActiveSync and than run this installation again.”
Step 3: Check the client application is installed completely in the mobile device.
1.2 Execute PDA / Smart Phone Client
1.2.1 Main Console setting
Step 1: Go to “Config” and select
“Network Service”
Network Service
page194
Intelligent Surveillance Solution
Appendix B
Step 2: Select “Live Streaming”, and then click “Start”.
Note:
The “Port” selected here will be the same with the one in PDA/Smart
Phone.
Live Streaming
Start
Port
1.2.2 Execute and Login
Step 1: Check your PDA/Smart Phone device is connected to network, and then go to Start > Programs > NUUO PDA / Smart Phone Client to execute application.
Step 2: Insert Address, Port, Name and Password of the server and click on
to login. page195
Intelligent Surveillance Solution
Appendix B
1.3 PDA/Smart Phone Client Overview
There are 3 main pages of Client application: Monitor Preview, I/O Control and System Info. Switch between these buttons to adjust overall configurations.
1.3.1 Live View
Live View
I/O control
System Info
Log out
Display
Camera List:
Display Live Video Back to Camera List
Display all “snapshots” of channels connected to server as camera list.
Click on indicated snapshot to get the channel information, and then click on to display live video.
Note:
The Screen Division and Refresh option could help to quick find the channel.
Screen Divisions
Refresh
page196
Intelligent Surveillance Solution
Appendix B
Live Video Display:
Live View panel could display “live video”, control PTZ, and snapshot.
Click to go back camera list.
PTZ Control: Click on PT Control Panel and Zoom Out/In to control physical PTZ camera or adjust digital PTZ under digital PTZ mode.
Note: To switch between “Digital PTZ” and “Physical PTZ”, simply click on button.
Zoom Out/In
Preset Go: Click to select indicated preset point.
PT Control
Snapshot: Click to take the snapshot and save it to default folder.
Full Screen: Click to toggle to the “Full Screen Mode”, right click on screen to obtain the PT control panel and disable full screen display.
Disable Full Screen
Enable Audio: Click to enable the audio of current channel.
1.3.2 I/O Control
Select “I/O Control” button to monitor status of DI/DO devices, and control DO devices. page197
Intelligent Surveillance Solution
Appendix B
DI/DO
I/O Device
I/O
I/O Device list :
Select and monitor the device connected with Server.
DI/DO status :
Monitor the DI/DO status synchronized with Server, and then click Output button to trigger the DO action.
Gray icon indicates the normal status of DI/DO devices.
Red icon indicates the alarm status of DI/DO devices.
Green icon indicates the synchronization process.
1.3.3 System Info
Display the server and client information. Server information includes address, post, and version. Client information includes login user, count of camera and I/O device with access authority and version. page198
Intelligent Surveillance Solution
Appendix C
Appendix C - Remote Desktop
Tool
How to install NUUO Remote Desktop Tool
Step 1: Insert the Installation CD.
Step 2: Please go to RemoteDesktopViewer directly and Run Setup.exe file.
How to Start NUUO Remote Desktop Tool
Step 1: Please point to Start > All Programs > NUUO Remote Desktop
Viewer > Remote Desktop Viewer.
Step 2: Please enter address, Port, Password of server. Enable the option
Use 8 bits color level to show steadier screen.
Step 3: Click OK to Start Remote Desktop.
page199
Advertisement
Key Features
- Live view
- Playback
- Remote live viewer
- Backup
- Verification tool
- Smart guard system
- Schedule recording
- System configuration
