Roland M-1000 Owner`s manual

Roland M-1000 Owner`s manual
Owner’s Manual
201b
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY
INSTRUCTIONS” (Owner’s manual p. 2), “USING THE UNIT SAFELY” (Owner’s manual p.
3), and “IMPORTANT NOTES” (Owner’s manual p. 5). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new unit,
Owner’s manual should be read in its entirety. The manual should be saved and kept on
hand as a convenient reference.
202
Copyright © 2002 ROLAND CORPORATION
All rights reserved.
No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
http://www.roland.co.jp/
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Never use with a cart, stand, tripod, bracket,
or table except as specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
204
* Microsoft and Windows are registered trademarks of Microsoft Corporation.
206c
* Windows® 98 is known officially as: “Microsoft® Windows® 98 operating system.”
206f
* Windows® 2000 is known officially as: “Microsoft® Windows® 2000 operating system.”
206g
* Windows® Me is known officially as: “Microsoft® Windows® Millennium Edition operating system.”
206h
* Windows® XP is known officially as: “Microsoft® Windows® XP operating system.”
207
* Apple and Macintosh are registered trademark of Apple Computer, Inc.
209
* MacOS is a trademark of Apple Computer, Inc.
233+
* VST and ASIO are trademark of Steinberg Media Technologies AG.
220
* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
2
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
to damage or
caused with
and all its
to domestic
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
009
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
008a
• The unit should be connected to a power supply
only of the type described in the operating instructions, or as marked on the unit.
..........................................................................................................
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
..........................................................................................................
012a:
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
008e
• Use only the attached power-supply cord.
..........................................................................................................
3
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
023
• DO NOT play a CD-ROM disc on a conventional
audio CD player. The resulting sound may be of a
level that could cause permanent hearing loss.
Damage to speakers or other system components
may result.
..........................................................................................................
101a
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..........................................................................................................
102b
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103a:
• Any accumulation of dust between the power
plug and the power outlet can result in poor
insulation and lead to fire. Periodically wipe away
such dust with a dry cloth. Also, disconnect the
power plug from the power outlet whenever the
unit is to remain unused for an extended period of
time.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107b
• Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from,
an outlet or this unit.
..........................................................................................................
108a
• Before moving the unit, disconnect the power
plug from the outlet, and pull out all cords from
external devices.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (p. 8).
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
118
• Should you remove rubber feet or screws of rack
mount angles, make sure to put them in a safe
place out of children's reach, so there is no chance
of them being swallowed accidentally.
..........................................................................................................
4
IMPORTANT NOTES
291b
In addition to the items listed under “IMPORTANT
SAFETY INSTRUCTIONS” and “USING THE UNIT
SAFELY” on p. 2 and p. 3, please read and observe the
following:
Power Supply
301
• Do not use this unit on the same power circuit with any
device that will generate line noise (such as an electric
motor or variable lighting system).
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this
unit; or move it farther away from the source of interference.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
557
• A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
562
• Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
Handling CD-ROMs
801
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean
using a commercially available CD cleaner.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
Copyright
852a’
• As this product is designed as professional equipment,
this unit can perform recording without being subject to
the restrictions of the Serial Copy Management System
(SCMS) even in case of exchanging audio signals through
a digital connection with an external instrument. This is
because the unit is intended solely for musical production,
and is designed not to be subject to restrictions as long as
it is used to record works (such as your own compositions) that do not infringe on the copyrights of others.
(SCMS is a feature that prohibits second-generation and
later copying through a digital connection. It is built into
MD recorders and other consumer digital-audio
equipment as a copyright-protection feature.)
853
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
Additional Precautions
• Do not use this unit for purposes that could infringe on a
copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of
third-party copyrights arising through your use of this
unit.
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
5
Contents
USING THE UNIT SAFELY......................................................................3
IMPORTANT NOTES ...............................................................................5
Contents ..................................................................................................6
Introduction .............................................................................................7
Main Features.............................................................................................................................................. 7
Accessories .................................................................................................................................................. 7
Basic Operation........................................................................................................................................... 7
Preparation....................................................................................................................................... 7
Turning On the Power.................................................................................................................... 8
Turning Off the Power ................................................................................................................... 8
Functions and Operation of Each Section ............................................................................................... 8
Examples of Use .....................................................................................9
Mixing Analog and Digital Inputs........................................................................................................... 9
Using the M-1000 with a Computer Connected Via USB................................................................... 10
Installing the USB Audio Driver................................................................................................. 11
Matching the Sampling Frequency............................................................................................. 11
Procedure for Changing the Settings ......................................................................................... 11
Indicator Status and Settings Status ........................................................................................... 11
USB Audio .............................................................................................12
What is a Driver?........................................................................................................................... 12
Types of Drivers ............................................................................................................................ 12
Advanced Mode and Standard Driver Mode ...................................................................................... 12
Advanced Mode ............................................................................................................................ 12
Standard Driver Mode ................................................................................................................. 13
Installing the Drivers ............................................................................................................................... 14
Installation Overview ................................................................................................................... 14
Deleting the Special Drivers (Uninstall)................................................................................................ 15
Explanations..........................................................................................16
Digital Connections.................................................................................................................................. 16
Other Points............................................................................................................................................... 17
Other Features ......................................................................................18
Initializing the Settings
---Restoring the M-1000 to Its Original Factory Conditions............................................................... 18
Changing the Signal Path for the Analog Output (MIX OUT)
- If the audio in the inputs is doubled in the output when using the USB connection -............... 18
Troubleshooting....................................................................................19
Concerning Copyright ..........................................................................20
About SCMS .............................................................................................................................................. 20
Disclaimer of liability............................................................................................................................... 20
About the License Agreement ................................................................................................................ 20
Specifications........................................................................................21
block diagram........................................................................................22
Index.......................................................................................................23
6
Introduction
Main Features
• Features four pairs of stereo (eight-channels) digital audio input plus one
pair of stereo (two-channels) analog audio input.
• Connects to computers via USB for input and output of digital audio signals.
• Each digital audio signal input is equipped with a sample rate converter,
thus allowing you to mix even inputs with different sampling frequencies
and phases.
Accessories
The following additional items are shipped with the M-1000. Please take a moment
to confirm that all of the following items have been included in the box.
• Owner's Manual (this volume)
• “Functions and Operations of Each Section” chart
• CD-ROM (Driver)
• USB cable
• Rubber feet (4)
• Power cable
Basic Operation
■ Preparation
Attaching the rubber feet
If necessary, attach the rubber feet on the
bottom panel as shown in the figure.
Setup
Mount the M-1000 in rack mount, set it on a table or desk, or in another suitable
location.
* If the M-1000 is placed directly above a power amp, the heat generated by the amp may
adversely affect the M-1000.
Connecting the Power Source
M-1000
rear panel
Use the included power cable to
connect the unit with a power source.
power cable
The pin assignment for the XLR type connectors
* The pin assignment for the XLR type connectors is as shown below.
Before making any connections, make sure that this pin assignment
is compatible with that of all your other devices.
7
Introduction
■ Turning On the Power
* Once the connections have been completed (p. 7, p. 9, p. 10), turn on power to your
various devices in the order specified. By turning on devices in the wrong order, you risk
causing malfunction and/or damage to speakers and other devices.
1.
Turn down the volume completely on all devices.
2.
Press the POWER switch on the M-1000's front panel to turn on the power.
If the M-1000 is operating properly, the indicators should show the current
settings. If set to the default factory settings, the [INT] and [44.1kHz]
indicators light if no input or output device is connected. In other cases,
indicators show the current settings or connections.
* This unit is equipped with a protection circuit. A brief interval of a few seconds is
required after power up before the unit will operate normally.
■ Turning Off the Power
1.
Turn down the volume completely on all devices.
2.
Press the POWER switch on the M-1000's front panel to turn off the power.
Functions and Operation of
Each Section
For a look at the features found in each section and how to use them,
refer to the A3-size chart “Functions and Operations of Each Section.”
8
“Examples of Use” (p. 9)
Examples of Use
* To prevent malfunction and/or damage to speakers or other devices, always turn down
the volume, and turn off the power on all devices before making any connections.
Mixing Analog and Digital Inputs
As shown in the following figure, you can connect synthesizers and audio sources,
and then mix these inputs.
* For instructions on what to do in each section, refer to the separate “Functions and
Operations of Each Section” chart.
Analog Input
Digital Input
Amp/Digital Recorder
Try inputting signals with the
ANALOG INPUT SENS (sensitivity)
switch set to [-10 dB].
If the PEAK indicator lights, switch
this to [+4 dB].
If using one digital input, set the
DIGITAL INPUT SELECT switch to
match the input (coaxial or optical)
connector being used.
Confirm that the LOCK indicator for
the input being used is lit.
Adjust the volume with the LEVEL
The sampling frequency of the
connected digital recorder is
synchronized to the M-1000.
Adjust the output volume with the
LEVEL (inner) knob.
Adjust the left-right volume balance
with the BALANCE (outer) knob.
Adjust the volume
to a comfortable level.
Headphones
MASTER
OUT
LINE IN
DIGITAL IN
Amp
DIGITAL OUT
Digital
DIGITAL OUT
Analog
Digital Recorder
Digital
9
Examples of Use
Using the M-1000 with a Computer Connected Via USB
You can use the M-1000 with computers by connecting as shown in the following figure.
• Mixing the input from digital inputs 1--3 and the analog input with sounds
played back from the computer
• Mixing the input from digital inputs 1--3 and the analog input, and recording
this to the computer
• Recording the mixed input from digital inputs 1--3 and the analog input to the
computer while playing back previously recorded sounds with the computer.
To record or play audio on computers, application software is necessary. (The
application software pre-installed to MacOS or Windows can be used for such purpose.)
* For instructions on what to do in each section, refer to the separate “Functions and
Operations of Each Section” chart.
Digital Input
Analog Input
Try inputting signals with the
ANALOG INPUT SENS (sensitivity)
switch set to [-10 dB].
If the PEAK indicator lights, switch
this to [+4 dB].
If using one digital input, set the
DIGITAL INPUT SELECT switch to
match the input (coaxial or optical)
connector being used.
Confirm that the LOCK indicator for
the input being used is lit.
Adjust the volume with the LEVEL
knob.
Four digital inputs accept sounds from
computers.
The M-1000 mix output can be
sent to the USB port, and then
the USB port can return this
signal along with its own
audio as the USB input to the
M-1000. However, signals
played back with the computer
cannot be returned and used
by the computer via USB
(computer → USB → M-1000
→ USB → computer).
Outputting to the
Computer (and MASTER
Output)
Adjust the volume level input to the
computer with the LEVEL (inner)
knob.
Adjust the left-right balance of the
sound input to the computer with the
BALANCE (outer) knob.
Adjust the volume
to a comfortable level.
Inputting from the Computer
The LOCK indicator lights up when the M-1000 is
connected to a computer with a USB cable.
Adjust the volume of the sound from the computer.
Headphones
DIGITAL OUT
MASTER
OUT
Digital
USB
Computer
Install the USB audio driver
and make the appropriate settings.
When connecting with USB,
you cannot input signals
through input 4.
DIGITAL OUT
Digital
10
Analog
Examples of Use
■ Installing the USB Audio Driver
To connect a computer via USB, you first need to install the USB audio driver. Read
the section “Installing the Drivers” (p. 14), then perform the installation as
instructed. For better sound, we strongly recommend using the M-1000 in
“Advanced Mode” (p. 12).
■ Matching the Sampling Frequency
When exchanging audio signals between the M-1000 and a computer via a USB
connection, set both the software and the M-1000 to the same sampling frequency.
Although there are applications capable of exchanging audio signals with differing
sampling frequencies, this may reduce the sound quality.
■ Procedure for Changing the Settings
You need to switch off the M-1000, then turn it on again after you've changed the
driver or sampling frequency settings when the M-1000 is connected to a computer
via USB.
1.
Quit all applications that make use of USB audio.
2.
Press the USB driver select button/sampling frequency select buttons a
number of times until the desired indicators flash (reserved status).
3.
Turn off the M-1000, then turn it on again.
4.
Start up your application or applications.
■ Indicator Status and Settings Status
The flashing light indicates
the “reserved” setting;
when the M-1000 is turned
off, then on again, that
setting is enabled, and the
indicator then remains lit.
Lit
Off
Standard Driver Mode
44.1 kHz
Advanced Mode
48 kHz
Standard Driver Mode
48 kHz
Advanced Mode
96 kHz
Input from Computer
Advanced Mode
44.1 kHz
Advanced Mode
96 kHz
Output to Computer
11
USB Audio
If using the M-1000 with a computer connected, you will need to install the USB
audio driver on the computer.
* For latest information about driver etc., please refer to Roland web site.
http://www.roland.co.jp/
USB:
Universal Serial Bus
■ What is a Driver?
application
Drivers are software programs that allow data to be
software
exchanged between computer applications and the
USB cable
driver
M-1000 when the M-1000 is connected to the
M-1000
computer with a USB cable.
computer
The driver transmits data from applications to the
M-1000 and also relays data from the M-1000 back to the applications.
■ Types of Drivers
The following chart shows the drivers that can be used according to your operating
system (such as Windows XP or Mac OS).
WindowsXP/2000
WindowsMe/98
MacOS
M-1000 Special WDM Driver
c c ADVANCED
44.1kHz/48kHz/96kHz:fromPC/96kHz:toPC
M-1000 Special MME Driver
c c ADVANCED
44.1kHz/48kHz/96kHz:fromPC/96kHz:toPC
Windows Standard Driver
c c 44.1kHz/48kHz
M-1000 Special Driver
c c ADVANCED
44.1kHz/48kHz/96kHz:fromPC/96kHz:toPC
Windows Standard Driver
c c 44.1kHz/48kHz
M-1000 Special Driver
(under MacOS 8.6: not supported)
c c ADVANCED
44.1kHz/48kHz/96kHz:fromPC/96kHz:toPC
MacOS Standard Driver
c c 44.1kHz/48kHz
The special driver supports
ASIO.
(under MacOS 9.0.4: not supported)
Advanced Mode and Standard Driver Mode
The M-1000 features two operational modes, Advanced mode and Standard Driver
mode, each of which uses different drivers.
■ Advanced Mode
This mode is operational when the [ADVANCED] USB indicator is lit. Using the
special drivers provided on the M-1000 Driver CD-ROM, you can input and output
high-quality audio data with great stability in timing.
In Advanced mode, audio signals are exchanged between the M-1000 and the
computer using 24-bit resolution, with sampling frequencies of 44.1 kHz, 48 kHz,
and 96 kHz supported. Set the M-1000 to Advanced mode when using software
capable of handling input and output of high-quality audio, including programs by
Cakewalk, Cool Edit, and other 24-bit compatible software, and applications that
support ASIO, such as Cubase VST, Logic Audio, SingerSongWriter, and Metro.
You cannot play back audio data (audio CDs, alert sounds, etc.) from Macintosh's
Sound Manager in Advanced mode.
12
ASIO:
Steinberg Audio Stream In/
Out Interface
USB Audio
When Using Windows XP/2000 (WDM Driver/MME Driver)
The M-1000 Driver CD-ROM includes two different drivers for use with Windows
XP and Windows 2000, the WDM driver and the MME driver.
You cannot have both installed; select one according to the software you are using.
WDM Driver
Use this driver if you have SONAR or a similar application set to WDM Driver
mode. This will allow you to obtain very good audio performance.
* 24-bit resolution is not available with Cool Edit, Media Player, and other applications
that have no WDM Driver mode.
WDM:
Win32 Driver Model
MME Driver
Cool Edit and similar programs that have no WDM Driver mode cannot be used
with 24-bit resolution.
* The MME driver cannot be used with SONAR or similar applications while in WDM
Driver mode.
MME:
Microsoft Multimedia
Extensions
You cannot have both the WDM Driver and MME Driver installed at the
same time. Select one, then install that driver. If after installing one of the
drivers you want to change it, always be sure to delete the installed driver
before installing the new driver.
→ “Deleting the Special Drivers (Uninstall)” (p. 15)
■ Standard Driver Mode
This mode is operational when the [ADVANCED] USB indicator is off.
This mode uses the standard USB drivers included with Windows and Macintosh.
In Standard Driver mode, audio signals exchanged between the M-1000 and the
computer feature 16-bit resolution, with sampling frequencies of 44.1 kHz and 48
kHz supported. Set the M-1000 to this mode when using applications in which audio
CDs are played back with the computer's built-in CD-ROM drive, that involve the
use software synthesizers included with Windows and Macintosh, or that utilize
functions specific to the Windows or Macintosh systems themselves.
* Drivers included with Windows and Macintosh do not support ASIO.
* The use of MacOS under MacOS 9.0.4 is not supported (standard driver mode).
Using the M-1000 After Switching Between Advanced Mode and
Standard Driver Mode
If you have both a special driver and the standard drivers installed, you
can then use the M-1000's USB driver select button (the CLOCK SOURCE
select button) to switch between Advanced mode and Standard Driver
mode.
* To enable the setting, quit all applications using the M-1000, including the
sequencer software, then turn the M-1000's power off, then on again.
→ “Procedure for Changing the Settings” (p. 11)
13
USB Audio
Installing the Drivers
■ Installation Overview
Although you can install the necessary drivers separately, to avoid the complications
involved with repeating installation and switching settings, we recommend starting
out by installing both the standard and special drivers.
The suggested procedure is described below.
* In case you are not familiar with software installation, please refer to the document on the
CD-ROM included with the M-1000 for more detailed instruction.
Windows
for standard driver: CD-ROM → “WinGenericDriver_E.htm”
for special driver:
CD-ROM → “Driver” folder → operating system version
you are using →(“WDM”/”MME”→) “ReadMe_E.htm”
Macintosh
for special driver:
CD-ROM → “Driver” folder → “ReadMe” folder →
“WDM Driver” (p. 13)
“MME Driver” (p. 13)
“English” folder → “ReadMe_E.htm”
for standard driver: CD-ROM → “WinGenericDriver_E.htm”
With Windows
1.
With the M-1000 disconnected, start up your computer.
If the setting is not default factory setting
2.Initialize the M-1000.
3.Turn the M-1000 off temporarily.
4.
Connect the M-1000 and the computer with a USB cable.
5.
Turn on the M-1000.
6.
Follow the instructions displayed to install the standard drivers. The M1000's USB indicator lights.
The instructions are not displayed if the drivers have already been installed; in this case, proceed to step 8.
7.
Re-boot the computer.
8.
During the re-boot procedure,
USB indicator or internal
indicator (INT) of M-1000
Press the CLOCK SOURCE button to switch the M-1000 to Advanced mode
(the light flashes).
irregulary blinks. But this is
not malfunction.
9.
Turn off the M-1000 (do not turn it on again just yet).
10. Open the folder on the included CD-ROM corresponding to the operating
system version you are using, then run “Setupinf.exe” in the “Driver”
folder.
Please confirm USB indicator
lits after re-booting.
11. Turn the M-1000 back on.
You can choose any sampling
rate.
12. Follow the instructions displayed to install the special driver. The M-1000's
USB and ADVANCED indicators light.
13. Go to “Start” → (“Settings” →) “Control Panels” → “Sound and Audio
Device” (, “Sound and Multimedia” or “Multimedia”); specify the M-1000
(or the USB audio device) as the priority device for audio.
14
Initialize:
Set the [SELECT] switch to the
optical setting, then hold down
the CLOCK SOURCE button
while turning on the M-1000
(p. 18).
USB Audio
With Macintosh
1.
With the M-1000 disconnected, start up your computer.
2.
Run “M-1000 USB Installer J” on the included CD-ROM.
3.
Follow the instructions displayed to install the special driver.
4.
Re-boot your computer.
5.
Connect the M-1000 and the computer with a USB cable.
6.
Turn on the M-1000. If in Advanced mode (ADVANCED indicator lit),
press the CLOCK SOURCE button to switch to Standard Driver mode
(ADVANCED indicator off), and turn the M-1000 off and then on again.
7.
Wait five seconds for the standard drivers to be recognized automatically,
then go to Control Panels in the Apple menu and open the “Sound” control
panel. For “Input,” specify “USB Audio” (required when using the
standard driver).
8.
Uncheck the “Play sound through output device” option.
9.
Switch the M-1000 to Advanced mode (the ADVANCED indicator should
flash; turn the M-1000 off and then on again).
During the re-boot procedure,
USB indicator or internal
indicator (INT) of M-1000
irregulary blinks. But this is
not malfunction.
Please confirm USB indicator
lits after re-booting.
You can choose any sampling
rate.
10. On the included CD-ROM, go to “Driver” → “ASIO” → “M-1000 ASIO1.0
16bit” and “M-1000 ASIO1.0 24bit.” Copy all of the drivers in the folder for
the ASIO-supported software you will be using to the “ASIO Drivers”
folder.
11. Specify “M-1000 ASIO1.0 16bit” or “M-1000 ASIO1.0 24bit” in the settings
screen in each ASIO application.
Deleting the Special Drivers (Uninstall)
If the special driver is not installed according to the prescribed procedure, or if there
is some other problem, the computer may fail to recognize the M-1000. If this occurs,
first delete then reinstall the special driver.
For the exact procedure, refer to the document on the CD-ROM included with the M1000.
Windows
CD-ROM → “Driver” folder → operating system version you are using →
“ReadMe_E.htm”
Macintosh
CD-ROM → “Driver” folder → “ReadMe” folder → “English” folder →
“ReadMe_E.htm”
15
Explanations
Digital Connections
Standards for Digital Input/Output
The M-1000 conforms to the “IEC60958,” “IEC 958" (input and output using a fixed
consumer format), and “EIAJ-CP-1201” (consumer format) standards for digital
input and output.
IEC:
International Electrotechnical
Commission
Word Clock and Sampling Frequency
When analog audio signals are converted into digital audio signals, the analog
signals are sampled at extremely short intervals of time, and those samples are
converted into a digital signal. The sampling frequency indicates how many times
this process is performed each second. The finer the divisions of time, the more
precise the conversion becomes.
In order to attain a high level of precision in the processing of digital audio signals
between multiple devices, these time segments must be synchronized. The signal
transmitted to achieve this is known as “word clock.”
When synchronizing, all the connected devices shall be specified as Word Clock
Master or Word Clock Slave (to control or to be controlled). In case you are using M1000 as Word Clock Slave (to be controlled), you need to specify the CLOCK SOURCE.
Word clock is transmitted via a different route (the [WORD CLOCK] connector) than
the audio signals, and all of the devices are synchronized to a single word clock. This
is used when synchronizing three or more devices.
EIAJ:
Electronic Industries
Association of Japan
WORD CLOCK [75Ω] and [THRU]
Example of synchronizing 3 units of M-1000
slave
slave
C
B
master
A
termination
Clock signal passes through
The units A, B and C will be
synchronized in exact timing.
slave
slave
C
B
master
A
termination
Re-create clock signal
The clock signal used for
syncronizaton of B unit will come
out to C unit. The lag between AC will be greater but the decline
of signal to C unit will be smaller.
[75Ω] ON/OFF (Termination ON/OFF)
When the M-1000 is connected as the terminus of a word clock connection,
termination is used (75Ω:ON). The resistance is 75 ohms, the same as that of the word
clock cable, and the signals are terminated.
If termination is not done correctly, it can disrupt the word clock signal's waveform,
causing distortion and noise in the sound. You only need to terminate the last device
in the chain.
16
The word clock signal
includes a high-frequency
component. When relaying
such signals, a measure
known as “termination”
needs to be used, in order
to prevent signals from
being reflected by both
ends of the cable.
Explanations
SRC
Normally, when transmitting digital audio signals between devices, including
digital sources sent to digital mixers, the sampling frequencies (SAMPLING FREQ)
of each device must be the same. If the different devices use differing rates, they
must be converted to the same master rate. In addition, the clocking or timing of the
clock signals of each signals of each signal must be exactly the same. This is usually
achieved by having one master clock and then slaving each digital device to that one
Master or Word Clock.
With the M-1000, each digital input 1--4 features its own sample rate converter
(SRC). This allows you to use devices that are set to different digital clock rates and
also that are not synchronized with each other by use of a master Word Clock. Each
input in the M-1000 is able to receive the following rates.
DIGITAL INPUT 1:
DIGITAL INPUT 2--4:
SRC:
Sample Rate Converter
Rate can be set to any frequency from 32 kHz to 96 kHz
Rate can be set to 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz,
or 96 kHz
The appropriate sample rate conversion is performed internally in the M-1000 and
the signals are all synchronized to the master clock signal according to the clock
source and sample frequency settings on the M-1000. This conversion and clock
synchronization is done automatically, making it very easy to mix multiple digital
devices.
SCMS
→“About SCMS” (p. 20)
Other Points
SCMS:
Serial Copy Management
System
Input Sensitivity Select Switch (SENS) and LEVEL Knobs
The input sensitivity select switch adjusts the input gain.
If the input volume level is set too low when converting an analog signal to digital,
the conversion accuracy suffers. Setting the input volume too high ends up
distorting the sound. Ideally, the input level prior to conversion should be as high as
possible without causing distortion. First, try a high input level with the input
sensitivity select switch set to [-10 dB]. If the PEAK indicator does not light, then use
the signal as is. If the PEAK indicator does light, it means the sound is going to be
distorted, so slide the switch to [+4 dB].
The LEVEL knobs work like channel faders on a digital recorder or similar device.
These adjust the volume level for each input. These affect the signals after they are
digitally converted.
MASTER Output and MONITOR Output
Both of these channel contain the mixed output of the M-1000. Normally, the
MASTER output is connected to house speakers or recording devices, and the
MONITOR output is connected to headphones or monitor speakers.
Although the output to the MONITOR bus is the same as the MASTER output,
changing the MONITOR output volume does not affect the volume of the MASTER
output.
17
Other Features
Initializing the Settings
---Restoring the M-1000 to Its Original Factory Conditions
You can use the following procedure to reset the settings to the default factory
condition.
1.
Set the SELECT switch to OPTICAL.
2.
Hold down the CLOCK SOURCE button and switch on the power to the
M-1000.
This resets the settings to their factory values.
Clock Source:
INT (Internal Clock)
Internal Clock Sampling Frequency:
44.1 kHz
USB Driver Mode:
Standard Driver Mode
Sampling Frequency w/USB Connection: 44.1 kHz
Changing the Signal Path for the Analog Output (MIX OUT)
- If the audio in the inputs is doubled in the output when using the USB connection The M-1000's internal signal
USB
routing incorporates a switch
called [MIX OUT].
Normally, sounds input to the M1000 are output both through the
ANALOG IN
MASTER OUT
USB connection and the MASTER
MIX OUT
output, but you can change the
[MIX OUT] setting to block the path from the analog input to the MASTER output.
When using the M-1000 in combination with another mixer, the way the connections
are made and the mixer is structured can cause sounds to be output twice. This
occurs in the following cases.
When connected via USB, the [MIX OUT] setting (Connect/Disconnect) is enabled.
When not connected via USB, [MIX OUT] remains connected at all times.
* Settings are saved even when the power is turned off.
Disconnecting the Path from ANALOG INPUT to MASTER OUT ([MIX OUT] off)
The analog input is transmitted only though USB.
Hold down the SAMPLING FREQ button for at least one second.
→The [96kHz], [48kHz], and [44.1kHz] indicators light for one second, indicating that the
path from ANALOG INPUT to MASTER OUT is disconnected.
Connecting the Path from ANALOG INPUT to MASTER OUT ([MIX OUT] on)
This is the normal setting. The analog input is sent both to the USB connector and
MASTER OUT.
Hold down the CLOCK SOURCE button for at least one second.
→The [ADVANCE], [96kHz:fromPC], and [96kHz:toPC] indicators light for one second,
indicating that the path from ANALOG INPUT to MASTER OUT is connected.
18
Troubleshooting
If the M-1000 does not operate as you expect, check the problems and solutions listed below first. If this does not solve
the problem, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed
on the “Information” (p. 26) page.
There is no sound.
This may be due to one or more of the following.
• The digital signals being input have a sampling rate that is not compatible with the M-1000.
→ Input signals that are compatible.
• The M-1000 is set to a sampling rate not compatible with the connected device.
→ Select a compatible sampling rate.
• The volume or level knob on the audio device is turned down too low.
→ Adjust to an appropriate level.
• The input sensitivity select switch is not at the right setting.
→ Try setting this to [-10dBu].
The volume level of the instrument connected to [ANALOG INPUT] is too low.
Could you be using a connection cable that contains a resistor?
→ Use a connection cable that does not contain a resistor.
The CLOCK SOURCE indicator is flashing.
This indicates that synchronization with the specified clock source could not be accomplished. In this case, the M-1000
switches to using its internal clock (INT).
This may be due to one or more of the following.
• The right signals are not reaching their corresponding connectors (such as when incompatible sampling rates are used).
• The M-1000 is not properly connected to the corresponding device.
→ Check the settings for the connected device, and make sure it is connected properly.
When connecting via USB, the indicators showing the driver and sampling rate are flashing.
These flash when you change USB-related settings. The flashing light indicates the “reserved” setting; when the M-1000
is turned off, then on again, that setting is enabled, and the indicator then remains lit.
→ When connecting via USB, turn the power off, then on again whenever you change the settings.
DIGITAL INPUT 1 is connected with a coaxial cable, but won't lock.
Is the digital input SELECT switch on the front panel set to OPTICAL?
→ Switch to match the connection.
Sounds cannot be exchanged with the PC after a change in the USB settings.
When changing settings, you need to exit all computer applications and restart the computer.
The volume levels for the device connected to the output connector is too low.
Could you be using a connection cable that contains a resistor?
→ Use a connection cable that doesn't incorporate a resistor (such as one from the Roland PCS Series).
Installation of the driver is requested when attempting to switch to USB Advanced mode.
If no M-1000 special driver has been installed, installation of the driver begins automatically if you try to switch to
Advanced mode.
→ Follow the instructions given to install the driver.
→ You can also follow the instructions in “Initializing the Settings ---Restoring the M-1000 to Its Original Factory
Conditions” (p. 18) to return to Standard Driver mode.
Sounds are doubled (played twice).
→ If using USB, try the procedure in “Disconnecting the Path from ANALOG INPUT to MASTER OUT ([MIX OUT]
off)” (p. 18).
19
Concerning Copyright
The law prohibits the unauthorized recording, public performance, broadcast, sale, or distribution etc. of a
work (CD recording, video recording, broadcast, etc.) whose copyright is owned by a third party.
Roland will take no responsibility for any infringement of copyright that you may commit in using the M1000.
About SCMS
SCMS (Serial Copy Management System) is a function that protects the rights of the copyright owner by
prohibiting second-generation or later copying via a digital connection to a consumer digital audio device
such as a DAT recorder or MD recorder. When a recording is made via a digital connection on a digital
recorder that has this function, SCMS data will be recorded along with the digital audio signal. A digital audio
signal containing this SCMS data cannot be recorded again via a digital connection.
Disclaimer of liability
Roland will take no responsibility for any “direct damages,” “consequential damages,” or “any other
damages” which may result from your use of the M-1000. These damages may include but are not limited to
the following events which can occur when using the M-1000.
• Any loss of profit that may occur to you
• Permanent loss of your music or data
• Inability to continue using the M-1000 itself or a connected device
About the License Agreement
The M-1000 is designed to allow you to reproduce material to which you have copyright, or material which
the copyrighted material without permission of the copyright owner avoiding technical prohibiting feature of
second-generation and later copying like SCMS or others constitutes copyright infringement and may incur
penalties even in case such reproduction is for your own personal use and enjoyment (private use). Consult a
copyright specialist or special publications for more detailed information on obtaining such permission from
copyright holders.
20
Specifications
Signal Processing
AD Conversion:
DA Conversion:
Internal Processing:
Sampling Frequency:
Indicators
24bits,64times oversampling
24bits,128times oversampling
56bits
96kHz,48kHz,44.1kHz
Analog Input
Connector:
1/4 inch phone type (unbalanced)
Input Level:
-10dBu, +4dBu (switchable)
Maximum Input Level: +22 dBu (Input Level:+4dBu)
Digital Input
Connector:
Format:
COAXIAL, OPTICAL
IEC 60958 & EIAJ CP-1201 [TYPEII/
Consumer]
24bits
Digital Input 1:
96kHz to 32kHz (variable)
Digital Input2--4:
96kHz, 88.2kHz, 48kHz,
44.1kHz, 32kHz
Number of Bits:
Sampling frequency:
Analog Output
Connector:
Output Level:
XLR-3-31 type (balanced)
1/4 inch phone type (unbalanced)
+4dBu (XLR-3-31 : Master Out)
-10dBu (1/4 inch phone : Monitor Out)
PEAK, LOCK, LEVEL METER,
CLOCK SOURCE, SAMPLE RATE
Power Supply
AC117V, AC230V, or AC240V
Power Consumption
10W
Dimensions
482 (W) x 167 (D) x 44 (H) mm
19 (W) x 6-5/8 (D) x 1-3/4 (H) inches
EIA-1U rack mount type
Weight
1.9kg
4 lbs 4 oz
Accessories
Owners Manual
Driver CD-ROM (Windows/Macintosh)
AC Cord
USB Cable
Rubber feet
Digital Output
Connector:
Format:
Number of Bits:
COAXIAL, OPTICAL
IEC 60958 & EIAJ CP-1201 [TYPEII/
Consumer]
24bits
Audio Specification
Signal-to-Noise Ratio: 102dB or less (IHF-A. typ.)
Frequency Response: 96.0kHz: 20Hz--40kHz (+0.1 / -2.0dB)
48.0kHz: 20Hz--22kHz (+0.1 / -2.0dB)
44.1kHz: 20Hz--20kHz (+0.1 / -2.0dB)
Total harmonic distortion:
0.001% or less (Input Level: +4dBu,
1kHz, Nominal Output)
USB Audio
Sampling frequency:
Number of Bits:
96kHz, 48kHz, 44.1kHz
24bits
Word Clock Terminal
Connector:
Input Impedance:
Input Signal Level:
Input Signal Frequency:
BNC
75Ω (terminator on)
TTL Level
96KHz, 88.2KHz, 48KHz,
44.1KHz, 32KHz
(0 dBu = 0.775 Vrms)
* In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
21
block diagram
block diagram
22
Index
Numerics
O
75Ω ................................................................................... 16
Operation .......................................................................... 8
A
P
ADVANCED ..................................................................
Advanced Mode ............................................................
ASIO ................................................................................
audio CD ........................................................................
12
12
12
13
PEAK indicator .............................................................. 17
phases ................................................................................ 7
pin assignment ................................................................. 7
Power ................................................................................ 8
B
R
block diagram ................................................................ 22
reserved .......................................................................... 11
resolution ........................................................................ 12
C
CD-ROM drive ..............................................................
Changing the Settings ...................................................
Clock Source ..................................................................
Computer .......................................................................
Copyright .......................................................................
13
11
16
10
20
D
Digital Connections ...................................................... 16
Driver ........................................................................ 12, 14
E
EIAJ ................................................................................. 16
F
flashing ........................................................................... 19
Functions and Operation of Each Section .................... 8
G
gain .................................................................................. 17
I
IEC ...................................................................................
Indicator ..........................................................................
Input Sensitivity Select Switch ....................................
Installing .........................................................................
16
11
17
14
L
LEVEL Knobs ................................................................. 17
M
Master ............................................................................. 16
MASTER Output ........................................................... 17
Matching the Sampling Frequency ............................. 11
Mixing ............................................................................... 9
MME ................................................................................ 13
MONITOR Output ........................................................ 17
S
sample rate converter ............................................... 7, 17
Sampling Frequency ..................................................... 16
SCMS ............................................................................... 20
SENS ................................................................................ 17
Signal Path ...................................................................... 18
Slave ................................................................................ 16
Sound Manager ............................................................. 12
SRC .................................................................................. 17
Standard Driver Mode .................................................. 13
Standards for Digital Input/Output .......................... 16
synchronized .................................................................. 16
T
Termination .................................................................... 16
THRU .............................................................................. 16
Turning Off the Power .................................................... 8
Turning On the Power .................................................... 8
U
Uninstall .......................................................................... 15
USB ............................................................................ 10, 12
USB Audio ...................................................................... 12
W
WDM ............................................................................... 13
Word Clock .................................................................... 16
Word Clock Master ....................................................... 16
Word Clock Slave .......................................................... 16
X
XLR type connectors ....................................................... 7
23
memo
24
memo
25
Information
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as
shown below.
AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
PANAMA
ITALY
ISRAEL
SUPRO MUNDIAL, S.A.
Roland Italy S. p. A.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
Halilit P. Greenspoon &
Sons Ltd.
CRISTOFORI MUSIC PTE
LTD
PARAGUAY
NORWAY
SINGAPORE
Swee Lee Company
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
URUGUAY
POLAND
Easa Husain Al Yousifi Est.
Todo Musica S.A.
P. P. H. Brzostowicz
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
Theera Music Co. , Ltd.
VENEZUELA
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
Musicland Digital C.A.
Tecnologias Musica e Audio,
Roland Portugal, S.A.
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
That Other Music Shop
(PTY) Ltd.
THAILAND
Paul Bothner (PTY) Ltd.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
P.O.BOX 23032, Claremont 7735,
SOUTH AFRICA
TEL: (021) 674 4030
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili
Chaoyang District, Beijing,
CHINA
TEL: (010) 6426-5050
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
TEL: 2415 0911
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
TEL: (022) 493 9051
INDONESIA
VIETNAM
Saigon Music
138 Tran Quang Khai St.,
District 1
Ho Chi Minh City
VIETNAM
TEL: (08) 844-4068
AUSTRALIA/
NEW ZEALAND
AUSTRALIA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
TEL: (02) 9982 8266
NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden,
Auckland, NEW ZEALAND
TEL: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
BRAZIL
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
JUAN Bansbach
Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Cosmos Corporation
CHILE
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
Comercial Fancy
BENTLEY MUSIC SDN BHD
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo ,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: 262-0788
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
TEL: (55) 5668-6699
26
AUSTRIA
PORTUGAL
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: (039)16 6200
FRANCE
Roland France SA
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: 01 600 73 500
FINLAND
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: (061) 043-5400
HUNGARY
FBS LINES
Piata Libertatii 1,
RO-4200 Gheorghehi
TEL: (095) 169-5043
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: (93) 308 1000
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
aDawliah Universal
Electronics APL
Corniche Road, Aldossary Bldg.,
1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
Technical Light & Sound
Center
Khaled Ebn Al Walid St.
Bldg. No. 47, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
SWITZERLAND
Barkat muzik aletleri ithalat
ve ihracat Ltd Sti
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 700139
MIDDLE EAST
BAHRAIN
Moon Stores
IRELAND
CYPRUS
Audio House, Belmont Court,
Donnybrook, Dublin 4.
Republic of IRELAND
TEL: (01) 2603501
SAUDI ARABIA
TURKEY
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 211 005
Roland Ireland
P.O. Box 62,
Doha, QATAR
TEL: 4423-554
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (08) 702 0020
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
Roland East Europe Ltd.
Chahine S.A.L.
Gerge Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
TEL: (01) 20-1441
Al Emadi Co. (Badie Studio
& Stores)
MuTek
DENMARK
LEBANON
ROMANIA
Siemensstrasse 4, P.O. Box 74,
A-6063 RUM, AUSTRIA
TEL: (0512) 26 44 260
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
QATAR
RUSSIA
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V.
KUWAIT
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
PORTUGAL
TEL: (022) 608 00 60
Roland Austria GES.M.B.H.
Roland Brasil Ltda
COSTA RICA
140 & 142, Jalan Bukit Bintang
55100 Kuala Lumpur,MALAYSIA
TEL: (03) 2144-3333
EUROPE
Lauttasaarentie 54 B
Fin-00201 Helsinki, FINLAND
TEL: (9) 682 4020
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
MALAYSIA
Av. Francisco de Miranda,
Centro Parque de Cristal, Nivel
C2 Local 20 Caracas
VENEZUELA
TEL: (212) 285-8586
Roland Scandinavia As,
Filial Finland
PT Citra IntiRama
KOREA
JORDAN
AMMAN Trading Agency
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (021) 492-124
SOUTH AFRICA
P.O.Box 32918, Braamfontein 2017
Johannesbourg, SOUTH AFRICA
TEL: (011) 403 4105
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 273 0074
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
TEL: (02) 2561 3339
11 Melle St., Braamfontein,
Johannesbourg, SOUTH AFRICA
Distribuidora De
Instrumentos Musicales
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
Siraselviler Caddesi Siraselviler
Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2499324
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai, U.A.E.
TEL: (04) 3360715
NORTH AMERICA
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
IRAN
MOCO, INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
As of August 1, 2002 (Roland)
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
27
03129056
’02-10-GE1-11KS
Caution: About Digital Audio Input/Output
The Digital IN connectors of M-1000 are compatible
with 2ch PCM audio only. In case M-1000 receives
audio signal in other formats (DTS, Dolby Surround
etc.), it outputs such signal as noise.
M-1000 does not have any multi-channel digital audio
encoding function such as the DTS format. And do
not input DTS signals or any other this kind of signals
to the digital input on M-1000. If you input DTS
signals to the digital input on M-1000, they cannot be
decoded into multi-channel signals. Please use an
external encode/decode device.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement