Wolf OG36 Installation guide
INSTALLATION GUIDE
Outdoor Gas Grills
Contents
Important Note
Wolf Outdoor Gas Grills . . . . . . . . . . . . . . . . . . . . . . . . 3
To ensure the safe and efficient use of Wolf equipment,
please take note of the following types of highlighted
information throughout this guide:
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Location Considerations . . . . . . . . . . . . . . . . . . . . . . . 5
Outdoor Grill Specifications . . . . . . . . . . . . . . . . . . . . . 6
Outdoor Grill Installation . . . . . . . . . . . . . . . . . . . . . . . 8
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Features and specifications in this guide and on the website
are subject to change at any time without notice. Check
our website, wolfappliance.com, for the most up-to-date
specifications.
IMPORTANT NOTE highlights information that is
especially important.
CAUTION signals a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
Wolf Outdoor Gas Grills
3
wolfappliance.com
Outdoor Grill Installation
Read this entire installation guide prior to installation and
save for the local inspector’s reference. The homeowner
should keep this installation guide for future reference.
The installation of this appliance must conform with local
codes or, in the absence of local codes, either the National
Fuel Gas Code, ANZI Z223.1/NFPA 54, or CAN/CGAB149.1, Natural Gas Installation Code or CAN/CGAB149.2, Propane Installation Code.
The utilization of an external electrical source requires that
when installed, this outdoor cooking gas appliance must
be electrically grounded in accordance with the local
codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22.1. Keep any electrical supply cord, or the
rotisserie motor cord and the gas supply hose away from
any heated surfaces.
This appliance must be installed in accordance with
National Electrical Codes, as well as all state, municipal
and local codes. The correct voltage, frequency and
amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly
sized circuit breaker or time delay fuse. The proper
voltage, frequency, and amperage ratings are listed on
the product rating plate.
Record the model and serial numbers before installing the
outdoor grill. Both numbers are listed on the product
rating plate, located behind the drip tray, below the logo.
The drip tray must be removed to view the rating plate.
Refer to the illustration below.
Wolf Outdoor Gas Grill
Model Number
Serial Number
RATING PLATE
Location of rating plate.
Safety Instructions
4
IMPORTANT INSTRUCTIONS
• Installation and service must be performed by a
WHAT TO DO IF YOU SMELL GAS:
qualified installer, service agency or the gas supplier.
•
Shut off gas supply to the appliance.
•
Extinguish any open flame.
•
Open hood.
•
If odor continues, keep away from the appliance
and immediately call your gas supplier or fire
department.
• Warranty service must be performed by a Wolf
authorized service center.
• Do not store or use gasoline or other flammable
liquids or vapors in the vicinity of this or any other
appliance. An LP gas cylinder not connected for use
shall not be stored in the vicinity of this or any other
appliance.
• In Massachusetts: All gas products must be installed
using a “Massachusetts” licensed plumber or gasfitter. A “T” handle type manual gas valve must be
installed in the gas supply line to this appliance. This
applies to permanently installed natural gas and
propane installations. This does not apply to propane
portable installations using a 20-lb tank.
BEFORE LIGHTING:
• Read instructions before lighting.
• Open hood during lighting.
• If ignition does not occur in 5 seconds, turn the
control knob off, wait 5 minutes, and repeat the
lighting procedure.
Location Considerations
5
wolfappliance.com
Locating the Grill
Built-In Applications
IMPORTANT NOTE: This gas appliance is designed and
certified for outdoor use only. Do not operate the grill
inside a building, garage, recreation vehicle or any
enclosed area.
Wolf outdoor grills are designed for easy placement into a
built-in enclosure. For installation in a combustible enclosure, the insulating liner must be used. Build the enclosure
according to specifications for your specific installation on
page 7. Note provisions required for the electrical supply
and gas line connection. Maintain specified clearances.
When choosing an area for the grill, whether a portable or
built-in application, consider exposure to wind, proximity
to traffic paths and length of gas supply line. Keep the gas
supply line as short as possible to reduce pressure drop.
Keep the grill away from windy areas but in a well ventilated area. Do not obstruct the flow of combustion and
ventilation air around the grill. The grill must be level and
flat. The supporting deck and countertop should also be
level and flat.
Both installations require a deck to support the grill. The
supporting deck should be level and flat and able to
support 300 lbs (136 kg).
It is recommended that ventilation holes be provided in the
enclosure so that gas will not become entrapped in the
event of a leak.
MINIMUM CLEARANCES
Do not locate grill under overhead combustible
surfaces.
Portable Applications
Wolf portable grill carts are available to fit all Wolf outdoor
grill models.
A minimum clearance of 12" (305) from the sides and 12"
(305) from the back of the grill to adjacent vertical
combustible construction must be maintained.
A minimum clearance of 21/2" (64) from the back of the
grill above cooking surface to non-combustible construction is required.
A minimum of 6" (152) clearance to the sides of the grill
above cooking surface to non-combustible construction is
recommended to provide space for the rotisserie motor
and the spit rod. The grill can be installed directly next to
non-combustible construction below the cooking surface.
INSULATING LINER
If the grill or sear module is being placed in a combustible
enclosure, an insulating liner is necessary to prevent fire,
property damage and bodily injury. Only use a Wolf insulating liner. Refer to the illustrations on page 7 and 9 for
installation specifications.
Outdoor Grill Specifications
6
Overall Dimensions
OUTDOOR GRILL
Model OG36 shown
30" (762)
OVERALL DEPTH
27"
(686)
OVERALL
HEIGHT
2 1/2"
12 1/2" (318)
TO GRILLING
SURFACE
(64)
CLEARANCE
FOR OPEN
HOOD
27 3/4" (705)
OVERALL WIDTH
GRILL CART
Model CART36 shown
12"
(305)
36 1/2"
24" (610)
TO GRILL
PLATFORM
(927)
OVERALL
HEIGHT
3" (76)
27 3/4" (705)
OVERALL WIDTH
MAX DOOR/DRAWER CLEARANCE 22" (559).
Outdoor Grill
Grill Cart
OVERALL WIDTH
Model OG30
Model OG36
Model OG42
W
OVERALL WIDTH
W
30" (762)
36" (914)
42" (1067)
Model CART30
Model CART36
Model CART42
30" (762)
36" (914)
42" (1067)
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are in millimeters unless otherwise specified.
Outdoor Grill Specifications
7
wolfappliance.com
Built-In Installations
COMBUSTIBLE ENCLOSURE
NON-COMBUSTIBLE ENCLOSURE
WITH INSULATING LINER
3/4"
(19)
3/4"
(19)
OPENING
FOR LINER
OPENING
FOR GRILL
COUNTERTOP
OVERHANG
COUNTERTOP
OVERHANG
12" (305) min TO
COMBUSTIBLE REAR SURFACES
2 1/2" (64) min TO
NON-COMBUSTIBLE REAR SURFACES
26"
24 1/4"
(660)
OPENING
DEPTH
GAS SUPPLY
(616)
OPENING
DEPTH
OPTIONAL
GAS SUPPLY
LOCATIONS
TOP VIEW
6" (152) min TO
NON-COMBUSTIBLE
SIDE SURFACES
TOP VIEW
12" (305) min TO
6" (152) min TO
NON-COMBUSTIBLE
SIDE SURFACES
OPENING WIDTH
COMBUSTIBLE
SIDE SURFACES
11 3/4"
COMBUSTIBLE
SIDE SURFACES
12 5/8" (321)
(298)
OPENING
HEIGHT
OPENING
HEIGHT
1" (25) min
GAS SUPPLY
OPENING WIDTH
FOR ACCESS DOORS OR
STORAGE DRAWERS
1" (25) min
GAS SUPPLY
36"
36"
(914)
(914)
OPENING WIDTH
FOR ACCESS DOORS OR
STORAGE DRAWERS
OPENING
HEIGHT
OPENING
HEIGHT
FRONT VIEW
FRONT VIEW
Non-Combustible Enclosure
Combustible Enclosure
OPENING WIDTH
W
28 1/2" (724)
34 1/2" (876)
40 1/2" (1029)
Model OG30
Model OG36
Model OG42
Optional Opening
ACCESS DOORS
18" (457) Single
30" (762) Double
36" (914) Double
42" (1067) Double
12" (305) min TO
OPENING WIDTH
OPENING WIDTH
W
33 1/2" (851)
39 1/2" (1003)
45 1/2" (1156)
Model OG30
Model OG36
Model OG42
Optional Opening
W
H
16 1/4" (413)
28 1/4" (718)
34 1/4" (870)
40 1/4" (1022)
19" (483)
19" (483)
19" (483)
19" (483)
STORAGE DRAWERS
30" (762) Single
13" (330) Double
13" (330) Triple
30" (762) Double with Door
W
H
27 1/4" (692)
12 1/8" (308)
12 1/8" (308)
29 1/4" (743)
9 3/4" (248)
19" (483)
19" (483)
19" (483)
Outdoor Grill Specifications
8
Overall Dimensions
SEAR MODULE
Model SM13
30" (762)
OVERALL DEPTH
12 1/2" (318)
OVERALL
HEIGHT
27 3/4" (705)
13" (330)
OVERALL
WIDTH
BURNER MODULE AND SIDE BURNER
Models BM13 and SB13
30" (762)
OVERALL DEPTH
10 3/4" (273)
OVERALL
HEIGHT
13" (330)
OVERALL
WIDTH
27 3/4" (705)
Outdoor Grill Specifications
9
wolfappliance.com
Module Installations
NON-COMBUSTIBLE ENCLOSURE
COMBUSTIBLE ENCLOSURE
WITH INSULATING LINER (MODEL SM13 ONLY)
3/4"
(19)
OPENING
FOR
MODULE
COUNTERTOP
OVERHANG
TOP VIEW
TOP VIEW
2 1/2" (64) min TO NON-COMBUSTIBLE
12" (305) min TO COMBUSTIBLE
REAR SURFACES
REAR SURFACES
24 1/4"
(616)
OPENING
DEPTH
6" (152) min TO
NON-COMBUSTIBLE
SIDE SURFACES
OPENING
HEIGHT
24" (610)
OPENING
DEPTH
GAS
SUPPLY
12"
(305)
OPENING
WIDTH
6" (152) min TO
NON-COMBUSTIBLE
SIDE SURFACES
OPENING
WIDTH
12" (305) min TO
COMBUSTIBLE
SIDE SURFACES
GAS
SUPPLY
36"
36"
(914)
FRONT VIEW
Non-Combustible Enclosure
Model SM13
Model BM13
17 3/4" (451)
COMBUSTIBLE
SIDE SURFACES
(914)
FRONT VIEW
OPENING HEIGHT
12" (305) min TO
10 3/4" (273)
OPENING HEIGHT
GAS
SUPPLY
GAS
SUPPLY
H
113/4" (298)
10" (254)
Outdoor Grill Installation
10
Electrical Requirements
Gas Safety Requirements
INSTALL THE POWER TRANSFORMER
IMPORTANT NOTE: The outdoor gas grill must be
connected to a regulated gas supply by a qualified technician and in accordance with local codes and ordinances.
Wolf outdoor grills have a power transformer for the lights
and igniters which is concealed in a stainless steel box
with an attached power supply cord.
CART APPLICATION: Two mounting screws with nuts are
provided at the bottom right rear corner of the cart to
secure the transformer box.
BUILT-IN APPLICATION: Secure the transformer box in a
dry location, away from the grill firebox and excessive heat
area, but within 2' (.6 m) of the right rear grill opening.
IMPORTANT NOTE: Do not install the transformer box
inside the insulating liner. The transformer box must be
secured away from excessive heat and in a dry location.
Make the transformer connections to the wire harness
located at the right rear of the grill to the harness of the
transformer box.
Plug the power cord from the transformer into a properly
grounded GFCI 120 V AC outlet. The outlet must be
located within 6' (1.8 m) of the transformer.
ROTISSERIE MOTOR
The rotisserie motor requires a GFCI 120 V AC electrical
supply. The 9' (2.7 m) power cord on the motor is
equipped with a 3-prong grounded plug for protection
against shock hazard.
ELECTRICAL GROUNDING: The outdoor gas grill is
equipped with a 3-prong grounding plug for protection
against shock hazard. It should be plugged directly into
a properly grounded 3-prong outlet. Do not cut or
remove the grounding prong from the plug.
DO NOT use an extension cord or two-prong adapter.
Each appliance is set and tested at the factory for the type
of gas supply to be used. Identify the type of gas, either
natural gas or LP gas, and make sure that the type of gas
specified on the product rating plate matches the gas
being supplied to the grill. Refer to page 3 for location of
the rating plate.
Conversion kits are available for both LP and natural gas
grills. Contact your Wolf dealer for more information.
Outdoor Grill Installation
11
wolfappliance.com
Gas Supply Requirements
Natural Gas Installations
Connect the grill to the gas supply line. The gas supply
line must be of adequate size to properly service all gas
appliances. Wolf recommends the use of a minimum 1/2"
(13) I.D. commercial type flex hose from the gas supply
line to the grill connection. The units will operate on 1/2"
(13) pipe to a maximum run of 30' (9 m). All plumbing to
the flex hose must be 3/4" (19) minimum I.D. pipe.
The natural gas pressure regulator provided with natural
gas grills is set for 4" (10 mb) WC (water column) and is
for use with natural gas only.
IMPORTANT NOTE: For complete gas shutdown, an
external gas shut-off valve must be located near the appliance in an accessible location. Refer to the illustration.
Ensure that the gas supply hose does not come in
contact with any hot surface of the grill.
NATURAL GAS SAFETY REQUIREMENT
This gas appliance and its individual shut-off valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures greater than .5 psi (3.5 kPa).
This gas appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply piping
system at test pressures equal to or less than .5 psi
(3.5 kPa).
NATURAL GAS CONNECTION
OPEN POSITION
TO APPLIANCE
A typical natural gas installation is shown in the illustrations below. Make sure that the pressure regulator
supplied with the grill is used and installed with the arrow
on the regulator pointing towards the grill. Do not use a
replacement regulator other than that specified by Wolf.
Use only gas piping that is approved for use with natural
and LP gases.
GAS SUPPLY
LINE
TO GRILL
Gas supply shut-off valve.
VENT
REGULATOR
REAR GAS
CONNECTION
ADAPTER
REGULATOR
CLOSE NIPPLE
BOTTOM GAS
CONNECTION
SHUT-OFF
VALVE
Natural gas connection.
FROM GAS
SUPPLY
Natural gas regulator.
Outdoor Grill Installation
12
LP Gas Installations
LP (liquefied petroleum) gas is sometimes called propane,
butane or bottled gas. It is a flammable gas which
becomes liquid when stored under high pressure inside a
cylinder and it vaporizes when released.
The LP gas pressure regulator provided with LP gas grills
is set for 10" (25 mb) WC (water column) and is for use
with LP gas only. The regulator comes connected to a
hose for use with a 20-lb LP gas cylinder.
LP GAS SAFETY REQUIREMENT
The LP gas cylinder must be provided with an approved
overfilling preventive device (OPD).
Any LP gas cylinder used with this appliance must be
constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (D.O.T.) or the National Standards of Canada
CAN/CSA-B339, Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods, and Commission, as
applicable. Provided with a listed overfilling prevention
device and a cylinder connection device compatible with
the connection for outdoor cooking appliances.
The LP gas cylinder must be provided with a shut-off valve
terminating in the cylinder valve outlet. It must include a
collar to protect the cylinder valve. The cylinder supply
system must be arranged for vapor withdrawal. Do not use
a cylinder that is dented, rusted or has a damaged valve.
IMPORTANT NOTE: Do not operate the gas grill indoors or
in any enclosed area. If the gas grill is not in use, the gas
must be turned off at the LP gas cylinder. If the grill is to
be stored indoors, disconnect the cylinder and leave it
outdoors.
Outdoor Grill Installation
13
wolfappliance.com
LP Gas Installations
PORTABLE LP CONNECTION
LP GAS CONNECTION
One of the many features of the Wolf grill cart is the
pull-out shelf for easy access to the LP gas cylinder. It is
designed to hold a 20-lb (5 gallon capacity) LP gas
cylinder.
Install the pressure regulator and hose assembly supplied
with the grill as shown in the illustrations below. Connect
the 3/8" flare end of the hose to the grill coupling using a
3/4" open wrench. Do not apply pipe sealant to the 3/8"
flare connection. Connect the regulator to the LP cylinder
hand-tighten, do not use a wrench.
1) To install the LP gas cylinder, pull out the shelf and
place the cylinder on it.
2) Check to ensure that the gas valve on top of the
cylinder is closed.
3) Connect the LP gas regulator to the cylinder and
hand-tighten only. Open the cylinder valve. Check for
leaks according to the gas leak testing procedure on
page 12.
4) Tighten the thumb screw to secure the cylinder to the
shelf.
The LP pressure regulator and hose supplied with the
grill must be used without alteration.
Do not place more than one LP gas cylinder in an
enclosure at one time.
Always check for gas leaks after changing the LP gas
cylinder.
REGULATOR
COUPLING NUT
GRILL
COUPLING
TO GRILL
REGULATOR
VENT
HOSE
ASSEMBLY
VENT
LP GAS
CYLINDER
VENT
LP gas connection.
Grill cart pull-out shelf.
LP GAS
CYLINDER
LP gas regulator.
Outdoor Grill Installation
14
Gas Leak Testing
IMPORTANT NOTE: Never use the outdoor grill without
first testing the gas line connections for gas leaks.
Perform a gas leak test each time the LP gas cylinder is
connected to the regulator and any time part of the gas
system is disconnected or replaced. This applies to
natural gas as well as LP gas. Perform a leak test at least
once each year whether the LP gas cylinder has been
disconnected or not.
IMPORTANT NOTE: To prevent fire or explosion hazard,
do not smoke or permit sources of ignition in the area
while performing a leak test. Perform the gas leak test
outdoors in a well ventilated area.
Have a dealer check the LP gas cylinder for deterioration
when the tank is filled in accordance with regulations.
Immediately replace the cylinder if any deterioration is
found.
DO NOT use an open flame to check for gas leaks.
Use of an open flame could result in a fire, explosion
and bodily harm.
GAS LEAK TESTING PROCEDURE
1) Prepare a leak testing solution of soapy water by
combining a mixture of half liquid soap and half water
in a spray bottle.
2) Verify that all control knobs are in the OFF position.
3) Turn the cylinder valve knob counterclockwise one turn
to open.
4) Apply the leak testing solution by spraying on the pipe
joints, fittings and hose. Bubbles in the soap and water
solution indicate that a gas leak is present.
5) Stop the leak by tightening the loose joint or by
replacing the faulty part with a replacement part
recommended by the Wolf. Do not attempt to repair the
cylinder valve if it should become damaged. The
cylinder must be replaced.
6) If you are unable to stop the leak, shut off the gas
supply at the cylinder valve. Remove the LP gas
cylinder. Call a Wolf authorized service center.
IMPORTANT NOTE: Do not use the grill until the leak
has been fixed.
7) Push in and turn any control knob to the ON position to
release pressure in the hose and manifold.
8) Turn the control knob to the OFF position.
Outdoor Grill Installation
15
wolfappliance.com
Outdoor Grill Assembly
Install Grill to Cart
Wolf outdoor grills are produced fully assembled and
tested in the factory and require no major assembly in the
field. For the purpose of safe shipping and transit, some
parts such as the briquette trays, warming rack and rotisserie components are wrapped inside the grill and require
minor assembly.
Wolf portable grill carts are available to fit all Wolf outdoor
grill models.
Remove all packaging materials, labels and protective
plastic film from the grill.
IMPORTANT NOTE: Do not leave the grill or grill cart in the
sun with the protective plastic film on for an extended
period or it may be difficult to remove.
Verify that all grill components are included: control knobs,
hex-grates, large and small briquette tray assemblies,
rotisserie motor with bracket, spit rod and meat forks,
natural gas or LP gas regulator, basting pan, warming rack
and smoker box assembly.
TO INSTALL BRIQUETTE TRAYS
1) Place the briquette trays into the grill above the
burners with the flash tube at the front as shown in the
illustration below.
2) Place the hex-grates directly above the briquette trays
and make sure the square openings on the hex-grates
are at the front.
FLASH TUBE
Flash tube position.
1) In a cart application, two mounting screws with nuts
are provided at the bottom right rear corner of the cart
for the transformer. If not provided, drill two holes
using the transformer box as a template. Install the
transformer box.
2) Place grill onto cart. Leave enough room at the back
right rear of the cart to make connection to the
transformer.
3) Once connection to the transformer is made, slide the
grill back until it is fully engaged with the cart.
4) With grill in position, secure grill to cart with four
screws provided. Mounting holes in the upper back
corners of the grill will align with holes in the cart.
Secure with two screws. Remove the drip tray. Install
two screws through side mounting holes below the grill
front panel and into the cart.
Outdoor Grill Installation
16
Installation Checklist
Troubleshooting
IMPORTANT NOTE: To ensure a safe and proper installation, the following checklist should be completed by the
installer to ensure that no part of the installation has been
overlooked.
IMPORTANT NOTE: If the outdoor gas grill does not
operate properly, follow these troubleshooting steps:
Any questions or problems about the installation should
be directed to your Wolf dealer or Wolf customer service
at 800-332-9513. You can also visit our website at
wolfappliance.com.
All packaging material has been removed.
Specified clearances to combustible materials have
been maintained.
All burners light properly, individually and with adjacent
burners lit.
All flames appear normal.
• Verify that gas is being supplied to the grill.
• Check the gas supply and electrical connections to
ensure that the installation has been completed
correctly.
• Check that control knobs are turned to the ON position
and held in to active the igniters.
• Follow troubleshooting procedures as described in the
Wolf outdoor gas grills use & care guide.
• If the outdoor grill still does not work, contact a Wolf
authorized service center. Do not attempt to repair the
grill yourself. Wolf is not responsible for service
required to correct a faulty installation.
The drip tray slides freely and is properly placed.
The correct pressure regulator is connected for natural
or LP gas and set for 4" (10 mb) WC for natural gas or
10" (25 mb) WC for LP gas.
The LP gas cylinder is in an upright position and the
hose is not kinked.
The grill has been tested and is free of any gas leak.
The homeowner has been informed of the gas supply
shut-off valve location.
Be sure to disconnect the electrical and gas supply
before servicing.
Service Information
17
wolfappliance.com
Service Information
If service is necessary, maintain the quality built into your
outdoor grill by calling a Wolf authorized service center.
To obtain the name and number of a Wolf authorized
service center, check the contact & support section of our
website, wolfappliance.com or call Wolf customer service
at 800-332-9513.
When calling for service, you will need the outdoor grill
model and serial numbers. Both numbers are listed on the
product rating plate, located under the drip tray, below the
logo. The drip tray must be removed to view the rating
plate. Refer to the illustration on page 3 for location of the
rating plate.
The information and images in this guide are the copyright property of Wolf Appliance, Inc. Neither this guide nor any information or images contained
herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc. ©Wolf Appliance, Inc. all rights reserved.
WOLF APPLIANCE, INC.
P. O. BOX 44848 MADISON, WI 53744
814446 REV-B
5/ 2009
WOLFAPPLIANCE.COM
800.332.9513
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement